From: Jon Smirl <jonsmirl@gmail.com>
To: Grant Likely <grant.likely@secretlab.ca>
Cc: linuxppc-dev@ozlabs.org
Subject: Re: [PATCH] powerpc/mpc52xx: add Phytec phyCORE-MPC5200B-IO board (pcm032)
Date: Sun, 1 Mar 2009 19:46:20 -0500 [thread overview]
Message-ID: <9e4733910903011646g43b151c2m7c6dfe80ac07e80a@mail.gmail.com> (raw)
In-Reply-To: <9e4733910903011637q246eb82al140e87242f695413@mail.gmail.com>
On Sun, Mar 1, 2009 at 7:37 PM, Jon Smirl <jonsmirl@gmail.com> wrote:
> Just tried it on pcm030. If I uncomment the reg line the kernel won't
> boot at all. I don't get any output.
I hooked up a serial console instead of netcat.
## Booting image at 00500000 ...
Image Name: Linux-2.6.29-rc6-efika
Created: 2009-03-02 0:28:31 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1776985 Bytes = 1.7 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Booting using flat device tree at 0x400000
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 61028k/65536k available (3520k kernel code, 4448k reserved,
156k data, 122k bss, 168k init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 66.28 BogoMIPS (lpj=110848)
Mount-cache hash table entries: 512
net_namespace: 296 bytes
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Scanning bus 0000:00
Machine check in kernel mode.
Caused by (from SRR1=41030): Transfer error ack signal
Oops: Machine check, sig: 7 [#1]
dspeak01
Modules linked in:
NIP: c001be94 LR: c0158cb4 CTR: c001be04
REGS: c3823de0 TRAP: 0200 Not tainted (2.6.29-rc6-efika)
MSR: 00041030 <ME,IR,DR> CR: 28000022 XER: 20000000
TASK = c3824000[1] 'swapper' THREAD: c3822000
GPR00: 80000000 c3823e90 c3824000 c3856000 00000000 00000000 00000004 c3823eb8
GPR08: c03a9848 fcffc000 000008bc 0020213c 82000022 ffefffff 03ffe000 ffffffff
GPR16: 00000001 00000000 007ffc00 00000000 00000000 03ff8838 00000000 00000004
GPR24: 00000000 00000000 c3823eb8 00000000 00000004 00000000 c03c0000 c3856000
NIP [c001be94] mpc52xx_pci_read_config+0x90/0xec
LR [c0158cb4] pci_bus_read_config_dword+0x4c/0x74
Call Trace:
[c3823e90] [c0091238] ifind+0x18/0x6c (unreliable)
[c3823eb0] [c0158cb4] pci_bus_read_config_dword+0x4c/0x74
[c3823ee0] [c0278a90] pci_scan_single_device+0x24/0x4b0
[c3823f10] [c0159d50] pci_scan_slot+0x2c/0x84
[c3823f30] [c027b2d4] pci_scan_child_bus+0x40/0x108
[c3823f50] [c0351c34] pcibios_init+0xdc/0x190
[c3823f70] [c00038f4] do_one_initcall+0x58/0x19c
[c3823fe0] [c034614c] kernel_init+0x74/0xe0
[c3823ff0] [c00133d4] kernel_thread+0x4c/0x68
Instruction dump:
817e0040 5400801e 7c004b78 5769063a 64008000 7d290378 7c0004ac 912b0000
7c0004ac 813e0044 7c0004ac 7d604c2c <0c0b0000> 4c00012c 2f9c0004 57601ef8
---[ end trace 31fd0ba7d8756001 ]---
Kernel panic - not syncing: Attempted to kill init!
Rebooting in 180 seconds..
--
Jon Smirl
jonsmirl@gmail.com
next prev parent reply other threads:[~2009-03-02 0:46 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-02-25 15:32 [PATCH] powerpc/mpc52xx: add Phytec phyCORE-MPC5200B-IO board (pcm032) Wolfram Sang
2009-02-25 15:40 ` Wolfram Sang
2009-02-27 5:31 ` Grant Likely
2009-03-01 10:18 ` Wolfram Sang
2009-03-01 14:48 ` Grant Likely
2009-03-01 15:54 ` Jon Smirl
2009-03-01 22:47 ` Grant Likely
2009-03-02 0:37 ` Jon Smirl
2009-03-02 0:46 ` Jon Smirl [this message]
2009-03-02 1:07 ` Grant Likely
2009-03-02 2:15 ` Jon Smirl
2009-03-02 2:19 ` Jon Smirl
2009-03-02 4:33 ` Grant Likely
2009-03-03 8:12 ` Robert Schwebel
2009-03-07 2:01 ` Jon Smirl
2009-03-10 16:03 ` [PATCH v2] " Wolfram Sang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=9e4733910903011646g43b151c2m7c6dfe80ac07e80a@mail.gmail.com \
--to=jonsmirl@gmail.com \
--cc=grant.likely@secretlab.ca \
--cc=linuxppc-dev@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).