From: ayaka <ayaka@soulik.info>
To: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org, mark.rutland@arm.com,
linux@armlinux.org.uk, kgene@kernel.org, krzk@kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-samsung-soc@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH 2/2] ARM: dts: add TOPEET itop elite based board
Date: Wed, 24 Aug 2016 02:36:30 +0800 [thread overview]
Message-ID: <0192d6da-89ce-a158-1c15-48eebba7db3b@soulik.info> (raw)
In-Reply-To: <20160823181402.GA6302@rob-hp-laptop>
On 08/24/2016 02:14 AM, Rob Herring wrote:
> On Mon, Aug 22, 2016 at 10:18:09PM +0800, Randy Li wrote:
>> The TOPEET itop exynos 4412 have three versions base board. The
>> Elite version is the cheap one without too much peripheral devices
>> on it.
>>
>> Currently supported are serial console, wired networking(USB),
>> USB OTG in peripheral mode, USB host, SD storage, GPIO buttons,
>> PWM beeper, ADC and LEDs.
>>
>> Signed-off-by: Randy Li <ayaka@soulik.info>
>> ---
>> .../bindings/arm/samsung/samsung-boards.txt | 3 +
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/exynos4412-itop-elite.dts | 147 +++++++++++++++++++++
>> 3 files changed, 151 insertions(+)
>> create mode 100644 arch/arm/boot/dts/exynos4412-itop-elite.dts
>>
>> diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
>> index 0ea7f14..c5913ba 100644
>> --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
>> +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
>> @@ -22,6 +22,9 @@ Required root node properties:
>> * FriendlyARM
>> - "friendlyarm,tiny4412" - for Exynos4412-based FriendlyARM
>> TINY4412 board.
>> + * Topee
> Topeet?
>
>> + - "topeet,itop4412-elite" - for Exynos4412-based Topeet
>> + Elite base board.
>>
>> * Google
>> - "google,pi" - for Exynos5800-based Google Peach Pi
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 48e1d4e..8f47aa0 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -135,6 +135,7 @@ dtb-$(CONFIG_ARCH_EXYNOS4) += \
>> exynos4412-origen.dtb \
>> exynos4412-smdk4412.dtb \
>> exynos4412-tiny4412.dtb \
>> + exynos4412-itop-elite.dtb \
>> exynos4412-trats2.dtb
>> dtb-$(CONFIG_ARCH_EXYNOS5) += \
>> exynos5250-arndale.dtb \
>> diff --git a/arch/arm/boot/dts/exynos4412-itop-elite.dts b/arch/arm/boot/dts/exynos4412-itop-elite.dts
>> new file mode 100644
>> index 0000000..3e0863b
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/exynos4412-itop-elite.dts
>> @@ -0,0 +1,147 @@
>> +/*
>> + * TOPEET's Exynos4412 based itop board device tree source
>> + *
>> + * Copyright (c) 2016 SUMOMO Computer Association
>> + * https://www.sumomo.mobi
>> + * Randy Li <ayaka@soulik.info>
>> + *
>> + * Device tree source file for TOPEET iTop Exynos 4412 core board
>> + * which is based on Samsung's Exynos4412 SoC.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> +*/
>> +
>> +/dts-v1/;
>> +#include "exynos4412-itop-scp-core.dtsi"
>> +
>> +/ {
>> + model = "TOPEET iTop 4412 Elite board based on Exynos4412";
>> + compatible = "topeet,itop4412-elite", "samsung,exynos4412", "samsung,exynos4";
>> +
>> + chosen {
>> + bootargs ="console=ttySAC2,115200";
> Don't need console set with...
But could I set something like rootfs here ?
As the bootloader(old u-boot) offered by the vendor is brick, it is
impossible to save any something in u-boot.
>
>> + stdout-path = &serial_2;
> this set.
>
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> +
>> + led2 {
>> + label = "red:system";
>> + gpios = <&gpx1 0 GPIO_ACTIVE_HIGH>;
>> + default-state = "off";
>> + linux,default-trigger = "heartbeat";
>> + };
>> +
>> + led3 {
>> + label = "red:user";
>> + gpios = <&gpk1 1 GPIO_ACTIVE_HIGH>;
>> + default-state = "off";
>> + };
>> + };
>> +
>> + gpio-keys {
>> + compatible = "gpio-keys";
>> +
>> + home {
>> + lable = "GPIO Key Home";
> s/lable/label/
>
>> + linux,code = <KEY_HOME>;
>> + gpios = <&gpx1 1 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + back {
>> + lable = "GPIO Key Back";
> ditto...
>
>> + linux,code = <KEY_BACK>;
>> + gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + sleep {
>> + lable = "GPIO Key Sleep";
>> + linux,code = <KEY_POWER>;
>> + gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + vol_up {
>> + lable = "GPIO Key Vol+";
>> + linux,code = <KEY_UP>;
>> + gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + vol_down {
>> + lable = "GPIO Key Vol-";
>> + linux,code = <KEY_DOWN>;
>> + gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
>> + };
>> + };
>> +
>> + beep {
>> + compatible = "pwm-beeper";
>> + pwms = <&pwm>;
>> + pinctrl-0 = <&pwm0_out>;
>> + pinctrl-names = "default";
>> + };
>> +};
>> +
>> +&pinctrl_1 {
>> + ether-reset {
>> + samsung,pins = "gpc0-1";
>> + samsung,pin-function = <1>;
>> + samsung,pin-pud = <0>;
>> + samsung,pin-drv = <0>;
>> + };
>> +};
>> +
>> +&sdhci_2 {
>> + bus-width = <4>;
>> + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
>> + pinctrl-names = "default";
>> + broken-cd;
>> + cap-sd-highspeed;
>> + vmmc-supply = <&ldo23_reg>;
>> + vqmmc-supply = <&ldo17_reg>;
>> + status = "okay";
>> +};
>> +
>> +&ehci {
>> + status = "okay";
>> + /* In order to reset USB ethernet */
>> + samsung,vbus-gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>;
>> +
>> + port@0 {
>> + status = "okay";
>> + };
>> +
>> + port@2 {
>> + status = "okay";
>> + };
>> +};
>> +
>> +&exynos_usbphy {
>> + status = "okay";
>> +};
>> +
>> +&hsotg {
>> + dr_mode = "peripheral";
>> + status = "okay";
>> +};
>> +
>> +&serial_1 {
>> + status = "okay";
>> +};
>> +
>> +&serial_2 {
>> + status = "okay";
>> +};
>> +
>> +&pwm {
>> + pinctrl-0 = <&pwm1_out>;
>> + pinctrl-names = "default";
>> + samsung,pwm-outputs = <1>;
>> + status = "okay";
>> +};
>> +
>> +&adc {
>> + status = "okay";
>> +};
>> --
>> 2.7.4
>>
Thank you for correct my spell mistake. I would resend a new version in
this weekend. After I have done the clock driver samsung s5m8767 regualtor.
next prev parent reply other threads:[~2016-08-23 18:39 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-08-21 20:04 [PATCH 0/2] Add a new board for exynos 4412 Randy Li
2016-08-21 20:04 ` [PATCH 1/2] ARM: dts: Add TOPEET itop core board SCP package version Randy Li
2016-08-22 6:50 ` Marek Szyprowski
2016-08-22 8:28 ` Ayaka
2016-08-22 14:45 ` Chanwoo Choi
2016-08-22 14:49 ` ayaka
2016-08-22 14:18 ` [PATCH 0/2 v2] Add a new board TOPEET iTOP for exynos 4412 Randy Li
2016-08-22 14:18 ` [PATCH 1/2] ARM: dts: Add TOPEET itop core board SCP package version Randy Li
2016-08-22 14:18 ` [PATCH 2/2] ARM: dts: add TOPEET itop elite based board Randy Li
2016-08-22 18:59 ` kbuild test robot
2016-08-23 18:14 ` Rob Herring
2016-08-23 18:36 ` ayaka [this message]
2016-08-23 22:38 ` Rob Herring
2016-08-24 8:29 ` Ayaka
2016-08-28 11:21 ` [PATCH 0/4 v3] Add a new board TOPEET iTOP for exynos 4412 Randy Li
2016-08-28 11:21 ` [PATCH 1/4] ARM: dts: Add TOPEET itop core board SCP package version Randy Li
2016-08-28 21:13 ` Rask Ingemann Lambertsen
2016-08-30 7:16 ` Krzysztof Kozlowski
2016-08-31 12:58 ` [RESEND PATCH 1/3] " Randy Li
2016-08-31 18:42 ` Krzysztof Kozlowski
2016-08-31 19:49 ` Ayaka
2016-09-01 13:03 ` Bartlomiej Zolnierkiewicz
2016-09-01 16:12 ` Krzysztof Kozlowski
2016-08-28 11:21 ` [PATCH 2/4] ARM: dts: add TOPEET itop elite based board Randy Li
2016-08-30 7:32 ` Krzysztof Kozlowski
2016-08-31 12:59 ` [RESEND PATCH 2/3] " Randy Li
2016-09-01 13:07 ` Bartlomiej Zolnierkiewicz
2016-08-28 11:21 ` [PATCH 3/4] ARM: dts: add fimc support in exynos4412 TOPEET iTop Elite board Randy Li
2016-08-30 7:33 ` Krzysztof Kozlowski
2016-08-31 13:00 ` [PATCH 3/3 v3] devicetree: bindings: Add vendor prefix for Topeet Randy Li
2016-08-28 11:21 ` [PATCH 4/4] ARM: dts: samsung: add analog audio codec on TOPEET iTop 4412 Elite Randy Li
2016-08-30 7:35 ` Krzysztof Kozlowski
2016-08-30 7:04 ` [PATCH 0/4 v3] Add a new board TOPEET iTOP for exynos 4412 Krzysztof Kozlowski
2016-08-21 20:04 ` [PATCH 2/2] ARM: dts: add TOPEET itop elite based board Randy Li
2016-08-21 20:12 ` [PATCH 2/2 v2] " Randy Li
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=0192d6da-89ce-a158-1c15-48eebba7db3b@soulik.info \
--to=ayaka@soulik.info \
--cc=devicetree@vger.kernel.org \
--cc=kgene@kernel.org \
--cc=krzk@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=mark.rutland@arm.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).