[PATCH v2 0/2] ARM: dts: stm32: add SPI on STM32MP13 platform

[PATCH v2 0/2] ARM: dts: stm32: add SPI on STM32MP13 platform

[Alain Volmat]

This series adds DT entries related to all spi nodes for the
STM32MP13 platform.

v2: reorder all node properties, starting with compatible and reg

Alain Volmat (2):
  ARM: dts: stm32: add spi nodes into stm32mp131.dtsi
  ARM: dts: stm32: add pinctrl and disabled spi5 node in stm32mp135f-dk

 arch/arm/boot/dts/stm32mp13-pinctrl.dtsi | 23 ++++++++
 arch/arm/boot/dts/stm32mp131.dtsi        | 70 ++++++++++++++++++++++++
 arch/arm/boot/dts/stm32mp135f-dk.dts     |  7 +++
 3 files changed, 100 insertions(+)

-- 
2.25.1

[PATCH v2 1/2] ARM: dts: stm32: add spi nodes into stm32mp131.dtsi

[Alain Volmat]

Add the 5 instances of spi busses supported by the stm32mp131.

Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
---
 arch/arm/boot/dts/stm32mp131.dtsi | 70 +++++++++++++++++++++++++++++++
 1 file changed, 70 insertions(+)

diff --git a/arch/arm/boot/dts/stm32mp131.dtsi b/arch/arm/boot/dts/stm32mp131.dtsi
index da9e8a6ca663..dd35a607073d 100644
--- a/arch/arm/boot/dts/stm32mp131.dtsi
+++ b/arch/arm/boot/dts/stm32mp131.dtsi
@@ -97,6 +97,34 @@ scmi_shm: scmi-sram@0 {
 			};
 		};
 
+		spi2: spi@4000b000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4000b000 0x400>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI2_K>;
+			resets = <&rcc SPI2_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 39 0x400 0x01>,
+			       <&dmamux1 40 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi3: spi@4000c000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4000c000 0x400>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI3_K>;
+			resets = <&rcc SPI3_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 61 0x400 0x01>,
+			       <&dmamux1 62 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
 		uart4: serial@40010000 {
 			compatible = "st,stm32h7-uart";
 			reg = <0x40010000 0x400>;
@@ -142,6 +170,20 @@ i2c2: i2c@40013000 {
 			status = "disabled";
 		};
 
+		spi1: spi@44004000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x44004000 0x400>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI1_K>;
+			resets = <&rcc SPI1_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 37 0x400 0x01>,
+			       <&dmamux1 38 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
 		dma1: dma-controller@48000000 {
 			compatible = "st,stm32-dma";
 			reg = <0x48000000 0x400>;
@@ -189,6 +231,34 @@ dmamux1: dma-router@48002000 {
 			dma-channels = <16>;
 		};
 
+		spi4: spi@4c002000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4c002000 0x400>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI4_K>;
+			resets = <&rcc SPI4_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 83 0x400 0x01>,
+			       <&dmamux1 84 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi5: spi@4c003000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4c003000 0x400>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI5_K>;
+			resets = <&rcc SPI5_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 85 0x400 0x01>,
+			       <&dmamux1 86 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
 		i2c3: i2c@4c004000 {
 			compatible = "st,stm32mp13-i2c";
 			reg = <0x4c004000 0x400>;
-- 
2.25.1

[PATCH v2 2/2] ARM: dts: stm32: add pinctrl and disabled spi5 node in stm32mp135f-dk

[Alain Volmat]

Add pinctrl information and a disabled spi5 node within
stm32mp135f-dk.dts in order to use the spi5 bus which is
available via the GPIO expansion pins of the STM32MP135 Discovery board.

Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
---
 arch/arm/boot/dts/stm32mp13-pinctrl.dtsi | 23 +++++++++++++++++++++++
 arch/arm/boot/dts/stm32mp135f-dk.dts     |  7 +++++++
 2 files changed, 30 insertions(+)

diff --git a/arch/arm/boot/dts/stm32mp13-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp13-pinctrl.dtsi
index 749078ba9d42..efdd163eba30 100644
--- a/arch/arm/boot/dts/stm32mp13-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp13-pinctrl.dtsi
@@ -142,6 +142,29 @@ pins {
 		};
 	};
 
+	spi5_pins_a: spi5-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 7, AF6)>, /* SPI5_SCK */
+				 <STM32_PINMUX('H', 3, AF5)>; /* SPI5_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 8, AF5)>; /* SPI5_MISO */
+			bias-disable;
+		};
+	};
+
+	spi5_sleep_pins_a: spi5-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 7, ANALOG)>, /* SPI5_SCK */
+				 <STM32_PINMUX('A', 8, ANALOG)>, /* SPI5_MISO */
+				 <STM32_PINMUX('H', 3, ANALOG)>; /* SPI5_MOSI */
+		};
+	};
+
 	uart4_pins_a: uart4-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('D', 6, AF8)>; /* UART4_TX */
diff --git a/arch/arm/boot/dts/stm32mp135f-dk.dts b/arch/arm/boot/dts/stm32mp135f-dk.dts
index 3e2823332d51..de341d17e87d 100644
--- a/arch/arm/boot/dts/stm32mp135f-dk.dts
+++ b/arch/arm/boot/dts/stm32mp135f-dk.dts
@@ -116,6 +116,13 @@ &sdmmc1 {
 	status = "okay";
 };
 
+&spi5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi5_pins_a>;
+	pinctrl-1 = <&spi5_sleep_pins_a>;
+	status = "disabled";
+};
+
 &uart4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart4_pins_a>;
-- 
2.25.1

Re: [PATCH v2 0/2] ARM: dts: stm32: add SPI on STM32MP13 platform

[Alexandre TORGUE]

Hi Alain

On 7/25/22 09:52, Alain Volmat wrote:
> This series adds DT entries related to all spi nodes for the
> STM32MP13 platform.
> 
> v2: reorder all node properties, starting with compatible and reg
> 
> Alain Volmat (2):
>    ARM: dts: stm32: add spi nodes into stm32mp131.dtsi
>    ARM: dts: stm32: add pinctrl and disabled spi5 node in stm32mp135f-dk
> 
>   arch/arm/boot/dts/stm32mp13-pinctrl.dtsi | 23 ++++++++
>   arch/arm/boot/dts/stm32mp131.dtsi        | 70 ++++++++++++++++++++++++
>   arch/arm/boot/dts/stm32mp135f-dk.dts     |  7 +++
>   3 files changed, 100 insertions(+)
> 

Series applied on stm32-next.

Regards
Alex