* [PATCH 1/3] Convert cris to arch_gettimeoffset()
@ 2010-03-01 22:51 john stultz
2010-03-01 22:54 ` [PATCH 2/3] arm: Convert arm " john stultz
0 siblings, 1 reply; 5+ messages in thread
From: john stultz @ 2010-03-01 22:51 UTC (permalink / raw)
To: starvik, jesper.nilsson
Cc: lkml, Andrew Morton, linux-cris-kernel, Thomas Gleixner
This patch converts cris to use GENERIC_TIME via the arch_getoffset()
infrastructure, reducing the amount of arch specific code we need to
maintain.
The cris architecture is one of the last 2 arches that need to be
converted.
This patch applies on top of Linus' current -git tree
I've taken my best swing at converting this, but I'm not 100% confident
I got it right. My cross-compiler is now out of date (gcc4.2) so I
wasn't able to check if it compiled. Any assistance from arch
maintainers or testers to get this merged would be great.
thanks
-john
Signed-off-by: John Stultz <johnstul@us.ibm.com>
---
arch/cris/Kconfig | 6 ++++
arch/cris/kernel/time.c | 68 +---------------------------------------------
2 files changed, 8 insertions(+), 66 deletions(-)
diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig
index 7adac38..059eac6 100644
--- a/arch/cris/Kconfig
+++ b/arch/cris/Kconfig
@@ -20,6 +20,12 @@ config RWSEM_GENERIC_SPINLOCK
config RWSEM_XCHGADD_ALGORITHM
bool
+config GENERIC_TIME
+ def_bool y
+
+config ARCH_USES_GETTIMEOFFSET
+ def_bool y
+
config GENERIC_IOMAP
bool
default y
diff --git a/arch/cris/kernel/time.c b/arch/cris/kernel/time.c
index 074fe7d..a05dd31 100644
--- a/arch/cris/kernel/time.c
+++ b/arch/cris/kernel/time.c
@@ -42,75 +42,11 @@ unsigned long loops_per_usec;
extern unsigned long do_slow_gettimeoffset(void);
static unsigned long (*do_gettimeoffset)(void) = do_slow_gettimeoffset;
-/*
- * This version of gettimeofday has near microsecond resolution.
- *
- * Note: Division is quite slow on CRIS and do_gettimeofday is called
- * rather often. Maybe we should do some kind of approximation here
- * (a naive approximation would be to divide by 1024).
- */
-void do_gettimeofday(struct timeval *tv)
-{
- unsigned long flags;
- signed long usec, sec;
- local_irq_save(flags);
- usec = do_gettimeoffset();
-
- /*
- * If time_adjust is negative then NTP is slowing the clock
- * so make sure not to go into next possible interval.
- * Better to lose some accuracy than have time go backwards..
- */
- if (unlikely(time_adjust < 0) && usec > tickadj)
- usec = tickadj;
-
- sec = xtime.tv_sec;
- usec += xtime.tv_nsec / 1000;
- local_irq_restore(flags);
-
- while (usec >= 1000000) {
- usec -= 1000000;
- sec++;
- }
-
- tv->tv_sec = sec;
- tv->tv_usec = usec;
-}
-
-EXPORT_SYMBOL(do_gettimeofday);
-
-int do_settimeofday(struct timespec *tv)
+u32 arch_gettimeoffset(void)
{
- time_t wtm_sec, sec = tv->tv_sec;
- long wtm_nsec, nsec = tv->tv_nsec;
-
- if ((unsigned long)tv->tv_nsec >= NSEC_PER_SEC)
- return -EINVAL;
-
- write_seqlock_irq(&xtime_lock);
- /*
- * This is revolting. We need to set "xtime" correctly. However, the
- * value in this location is the value at the most recent update of
- * wall time. Discover what correction gettimeofday() would have
- * made, and then undo it!
- */
- nsec -= do_gettimeoffset() * NSEC_PER_USEC;
-
- wtm_sec = wall_to_monotonic.tv_sec + (xtime.tv_sec - sec);
- wtm_nsec = wall_to_monotonic.tv_nsec + (xtime.tv_nsec - nsec);
-
- set_normalized_timespec(&xtime, sec, nsec);
- set_normalized_timespec(&wall_to_monotonic, wtm_sec, wtm_nsec);
-
- ntp_clear();
- write_sequnlock_irq(&xtime_lock);
- clock_was_set();
- return 0;
+ return do_gettimeoffset() * 1000;
}
-EXPORT_SYMBOL(do_settimeofday);
-
-
/*
* BUG: This routine does not handle hour overflow properly; it just
* sets the minutes. Usually you'll only notice that after reboot!
--
1.6.0.4
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 2/3] arm: Convert arm to arch_gettimeoffset()
2010-03-01 22:51 [PATCH 1/3] Convert cris to arch_gettimeoffset() john stultz
@ 2010-03-01 22:54 ` john stultz
2010-03-01 22:56 ` [PATCH 3/3] time: Kill off CONFIG_GENERIC_TIME john stultz
2010-03-03 0:07 ` [PATCH 2/3] arm: Convert arm to arch_gettimeoffset() Andrew Morton
0 siblings, 2 replies; 5+ messages in thread
From: john stultz @ 2010-03-01 22:54 UTC (permalink / raw)
To: Russell King; +Cc: lkml, Andrew Morton, Thomas Gleixner, linux-arm-kernel
This patch converts arm to use GENERIC_TIME via the arch_getoffset()
infrastructure, reducing the amount of arch specific code we need to
maintain.
The arm architecture is one of the last 2 arches that need to be
converted.
This patch applies on top of Linus' current -git tree
I've taken my best swing at converting this, but I'm not 100% confident
I got it right. My cross-compiler is now out of date (gcc4.2) so I
wasn't able to check if it compiled. Any assistance from arch
maintainers or testers to get this merged would be great.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
---
arch/arm/Kconfig | 51 ++++++++++++++-------------
arch/arm/include/asm/mach/time.h | 2 +-
arch/arm/kernel/time.c | 70 +++----------------------------------
arch/arm/mach-at91/Kconfig | 11 +-----
4 files changed, 35 insertions(+), 99 deletions(-)
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 3b18128..ff8e0b4 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -42,6 +42,11 @@ config GENERIC_GPIO
config GENERIC_TIME
bool
+ default y
+
+config ARCH_USES_GETTIMEOFFSET
+ bool
+ default n
config GENERIC_CLOCKEVENTS
bool
@@ -224,6 +229,7 @@ config ARCH_AAEC2000
select CPU_ARM920T
select ARM_AMBA
select HAVE_CLK
+ select ARCH_USES_GETTIMEOFFSET
help
This enables support for systems based on the Agilent AAEC-2000
@@ -234,6 +240,7 @@ config ARCH_INTEGRATOR
select HAVE_CLK
select COMMON_CLKDEV
select ICST525
+ select ARCH_USES_GETTIMEOFFSET
help
Support for ARM's Integrator platform.
@@ -243,7 +250,6 @@ config ARCH_REALVIEW
select HAVE_CLK
select COMMON_CLKDEV
select ICST307
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select ARCH_WANT_OPTIONAL_GPIOLIB
help
@@ -256,7 +262,6 @@ config ARCH_VERSATILE
select HAVE_CLK
select COMMON_CLKDEV
select ICST307
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select ARCH_WANT_OPTIONAL_GPIOLIB
help
@@ -267,6 +272,7 @@ config ARCH_AT91
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
select HAVE_CLK
+ select ARCH_USES_GETTIMEOFFSET
help
This enables support for systems based on the Atmel AT91RM9200,
AT91SAM9 and AT91CAP9 processors.
@@ -274,6 +280,7 @@ config ARCH_AT91
config ARCH_CLPS711X
bool "Cirrus Logic CLPS711x/EP721x-based"
select CPU_ARM720T
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Cirrus Logic 711x/721x based boards.
@@ -282,6 +289,7 @@ config ARCH_GEMINI
select CPU_FA526
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
+ select ARCH_USES_GETTIMEOFFSET
help
Support for the Cortina Systems Gemini family SoCs
@@ -290,6 +298,7 @@ config ARCH_EBSA110
select CPU_SA110
select ISA
select NO_IOPORT
+ select ARCH_USES_GETTIMEOFFSET
help
This is an evaluation board for the StrongARM processor available
from Digital. It has limited hardware on-board, including an
@@ -306,6 +315,7 @@ config ARCH_EP93XX
select COMMON_CLKDEV
select ARCH_REQUIRE_GPIOLIB
select ARCH_HAS_HOLES_MEMORYMODEL
+ select ARCH_USES_GETTIMEOFFSET
help
This enables support for the Cirrus EP93xx series of CPUs.
@@ -313,13 +323,13 @@ config ARCH_FOOTBRIDGE
bool "FootBridge"
select CPU_SA110
select FOOTBRIDGE
+ select ARCH_USES_GETTIMEOFFSET
help
Support for systems based on the DC21285 companion chip
("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
config ARCH_MXC
bool "Freescale MXC/iMX-based"
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select ARCH_MTD_XIP
select GENERIC_GPIO
@@ -334,7 +344,6 @@ config ARCH_STMP3XXX
select HAVE_CLK
select COMMON_CLKDEV
select ARCH_REQUIRE_GPIOLIB
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select GENERIC_GPIO
select USB_ARCH_HAS_EHCI
@@ -346,7 +355,6 @@ config ARCH_NETX
select CPU_ARM926T
select ARM_VIC
select GENERIC_CLOCKEVENTS
- select GENERIC_TIME
help
This enables support for systems based on the Hilscher NetX Soc
@@ -354,6 +362,7 @@ config ARCH_H720X
bool "Hynix HMS720x-based"
select CPU_ARM720T
select ISA_DMA_API
+ select ARCH_USES_GETTIMEOFFSET
help
This enables support for systems based on the Hynix HMS720x
@@ -364,7 +373,6 @@ config ARCH_NOMADIK
select CPU_ARM926T
select HAVE_CLK
select COMMON_CLKDEV
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
@@ -379,6 +387,7 @@ config ARCH_IOP13XX
select PCI
select ARCH_SUPPORTS_MSI
select VMSPLIT_1G
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Intel's IOP13XX (XScale) family of processors.
@@ -390,6 +399,7 @@ config ARCH_IOP32X
select PCI
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Intel's 80219 and IOP32X (XScale) family of
processors.
@@ -402,6 +412,7 @@ config ARCH_IOP33X
select PCI
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Intel's IOP33X (XScale) family of processors.
@@ -410,6 +421,7 @@ config ARCH_IXP23XX
depends on MMU
select CPU_XSC3
select PCI
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Intel's IXP23xx (XScale) family of processors.
@@ -418,6 +430,7 @@ config ARCH_IXP2000
depends on MMU
select CPU_XSCALE
select PCI
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Intel's IXP2400/2800 (XScale) family of processors.
@@ -426,7 +439,6 @@ config ARCH_IXP4XX
depends on MMU
select CPU_XSCALE
select GENERIC_GPIO
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select DMABOUNCE if PCI
help
@@ -436,6 +448,7 @@ config ARCH_L7200
bool "LinkUp-L7200"
select CPU_ARM720T
select FIQ
+ select ARCH_USES_GETTIMEOFFSET
help
Say Y here if you intend to run this kernel on a LinkUp Systems
L7200 Software Development Board which uses an ARM720T processor.
@@ -451,7 +464,6 @@ config ARCH_DOVE
select PCI
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select PLAT_ORION
help
@@ -463,7 +475,6 @@ config ARCH_KIRKWOOD
select PCI
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select PLAT_ORION
help
@@ -473,7 +484,6 @@ config ARCH_KIRKWOOD
config ARCH_LOKI
bool "Marvell Loki (88RC8480)"
select CPU_FEROCEON
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select PLAT_ORION
help
@@ -485,7 +495,6 @@ config ARCH_MV78XX0
select PCI
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select PLAT_ORION
help
@@ -499,7 +508,6 @@ config ARCH_ORION5X
select PCI
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select PLAT_ORION
help
@@ -514,7 +522,6 @@ config ARCH_MMP
select ARCH_REQUIRE_GPIOLIB
select HAVE_CLK
select COMMON_CLKDEV
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select TICK_ONESHOT
select PLAT_PXA
@@ -526,6 +533,7 @@ config ARCH_KS8695
select CPU_ARM922T
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Micrel/Kendin KS8695 "Centaur" (ARM922T) based
System-on-Chip devices.
@@ -534,7 +542,6 @@ config ARCH_NS9XXX
bool "NetSilicon NS9xxx"
select CPU_ARM926T
select GENERIC_GPIO
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_CLK
help
@@ -550,7 +557,6 @@ config ARCH_W90X900
select GENERIC_GPIO
select HAVE_CLK
select COMMON_CLKDEV
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
help
Support for Nuvoton (Winbond logic dept.) ARM9 processor,
@@ -575,6 +581,7 @@ config ARCH_PNX4008
select CPU_ARM926T
select HAVE_CLK
select COMMON_CLKDEV
+ select ARCH_USES_GETTIMEOFFSET
help
This enables support for Philips PNX4008 mobile platform.
@@ -587,7 +594,6 @@ config ARCH_PXA
select HAVE_CLK
select COMMON_CLKDEV
select ARCH_REQUIRE_GPIOLIB
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select TICK_ONESHOT
select PLAT_PXA
@@ -597,7 +603,6 @@ config ARCH_PXA
config ARCH_MSM
bool "Qualcomm MSM"
select CPU_V6
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
help
Support for Qualcomm MSM7K based systems. This runs on the ARM11
@@ -615,6 +620,7 @@ config ARCH_RPC
select ISA_DMA_API
select NO_IOPORT
select ARCH_SPARSEMEM_ENABLE
+ select ARCH_USES_GETTIMEOFFSET
help
On the Acorn Risc-PC, Linux can support the internal IDE disk and
CD-ROM interface, serial and parallel port, and the floppy drive.
@@ -628,7 +634,6 @@ config ARCH_SA1100
select ARCH_HAS_CPUFREQ
select CPU_FREQ
select GENERIC_GPIO
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_CLK
select TICK_ONESHOT
@@ -641,6 +646,7 @@ config ARCH_S3C2410
select GENERIC_GPIO
select ARCH_HAS_CPUFREQ
select HAVE_CLK
+ select ARCH_USES_GETTIMEOFFSET
help
Samsung S3C2410X CPU based systems, such as the Simtec Electronics
BAST (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or
@@ -650,6 +656,7 @@ config ARCH_S3C64XX
bool "Samsung S3C64XX"
select GENERIC_GPIO
select HAVE_CLK
+ select ARCH_USES_GETTIMEOFFSET
select ARCH_HAS_CPUFREQ
help
Samsung S3C64XX series based systems
@@ -670,6 +677,7 @@ config ARCH_SHARK
select ISA_DMA
select ZONE_DMA
select PCI
+ select ARCH_USES_GETTIMEOFFSET
help
Support for the StrongARM based Digital DNARD machine, also known
as "Shark" (<http://www.shark-linux.de/shark.html>).
@@ -679,6 +687,7 @@ config ARCH_LH7A40X
select CPU_ARM922T
select ARCH_DISCONTIGMEM_ENABLE if !LH7A40X_CONTIGMEM
select ARCH_SPARSEMEM_ENABLE if !LH7A40X_CONTIGMEM
+ select ARCH_USES_GETTIMEOFFSET
help
Say Y here for systems based on one of the Sharp LH7A40X
System on a Chip processors. These CPUs include an ARM922T
@@ -692,7 +701,6 @@ config ARCH_U300
select HAVE_TCM
select ARM_AMBA
select ARM_VIC
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_CLK
select COMMON_CLKDEV
@@ -703,7 +711,6 @@ config ARCH_U300
config ARCH_DAVINCI
bool "TI DaVinci"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
@@ -722,7 +729,6 @@ config ARCH_OMAP
select HAVE_CLK
select ARCH_REQUIRE_GPIOLIB
select ARCH_HAS_CPUFREQ
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select ARCH_HAS_HOLES_MEMORYMODEL
help
@@ -734,7 +740,6 @@ config ARCH_BCMRING
select CPU_V6
select ARM_AMBA
select COMMON_CLKDEV
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select ARCH_WANT_OPTIONAL_GPIOLIB
help
@@ -744,7 +749,6 @@ config ARCH_U8500
bool "ST-Ericsson U8500 Series"
select CPU_V7
select ARM_AMBA
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select COMMON_CLKDEV
help
@@ -867,7 +871,6 @@ config ARCH_ACORN
config PLAT_IOP
bool
select GENERIC_CLOCKEVENTS
- select GENERIC_TIME
config PLAT_ORION
bool
diff --git a/arch/arm/include/asm/mach/time.h b/arch/arm/include/asm/mach/time.h
index 8bffc3f..35d408f 100644
--- a/arch/arm/include/asm/mach/time.h
+++ b/arch/arm/include/asm/mach/time.h
@@ -38,7 +38,7 @@ struct sys_timer {
void (*init)(void);
void (*suspend)(void);
void (*resume)(void);
-#ifndef CONFIG_GENERIC_TIME
+#ifdef CONFIG_ARCH_USES_GETTIMEOFFSET
unsigned long (*offset)(void);
#endif
};
diff --git a/arch/arm/kernel/time.c b/arch/arm/kernel/time.c
index 2875380..38c261f 100644
--- a/arch/arm/kernel/time.c
+++ b/arch/arm/kernel/time.c
@@ -72,12 +72,15 @@ unsigned long profile_pc(struct pt_regs *regs)
EXPORT_SYMBOL(profile_pc);
#endif
-#ifndef CONFIG_GENERIC_TIME
-static unsigned long dummy_gettimeoffset(void)
+#ifdef CONFIG_ARCH_USES_GETTIMEOFFSET
+u32 arch_gettimeoffset(void)
{
+ if (system_timer->offset != NULL)
+ return system_timer->offset() * 1000;
+
return 0;
}
-#endif
+#endif /* CONFIG_ARCH_USES_GETTIMEOFFSET */
#ifdef CONFIG_LEDS_TIMER
static inline void do_leds(void)
@@ -93,63 +96,6 @@ static inline void do_leds(void)
#define do_leds()
#endif
-#ifndef CONFIG_GENERIC_TIME
-void do_gettimeofday(struct timeval *tv)
-{
- unsigned long flags;
- unsigned long seq;
- unsigned long usec, sec;
-
- do {
- seq = read_seqbegin_irqsave(&xtime_lock, flags);
- usec = system_timer->offset();
- sec = xtime.tv_sec;
- usec += xtime.tv_nsec / 1000;
- } while (read_seqretry_irqrestore(&xtime_lock, seq, flags));
-
- /* usec may have gone up a lot: be safe */
- while (usec >= 1000000) {
- usec -= 1000000;
- sec++;
- }
-
- tv->tv_sec = sec;
- tv->tv_usec = usec;
-}
-
-EXPORT_SYMBOL(do_gettimeofday);
-
-int do_settimeofday(struct timespec *tv)
-{
- time_t wtm_sec, sec = tv->tv_sec;
- long wtm_nsec, nsec = tv->tv_nsec;
-
- if ((unsigned long)tv->tv_nsec >= NSEC_PER_SEC)
- return -EINVAL;
-
- write_seqlock_irq(&xtime_lock);
- /*
- * This is revolting. We need to set "xtime" correctly. However, the
- * value in this location is the value at the most recent update of
- * wall time. Discover what correction gettimeofday() would have
- * done, and then undo it!
- */
- nsec -= system_timer->offset() * NSEC_PER_USEC;
-
- wtm_sec = wall_to_monotonic.tv_sec + (xtime.tv_sec - sec);
- wtm_nsec = wall_to_monotonic.tv_nsec + (xtime.tv_nsec - nsec);
-
- set_normalized_timespec(&xtime, sec, nsec);
- set_normalized_timespec(&wall_to_monotonic, wtm_sec, wtm_nsec);
-
- ntp_clear();
- write_sequnlock_irq(&xtime_lock);
- clock_was_set();
- return 0;
-}
-
-EXPORT_SYMBOL(do_settimeofday);
-#endif /* !CONFIG_GENERIC_TIME */
#ifndef CONFIG_GENERIC_CLOCKEVENTS
/*
@@ -214,10 +160,6 @@ device_initcall(timer_init_sysfs);
void __init time_init(void)
{
-#ifndef CONFIG_GENERIC_TIME
- if (system_timer->offset == NULL)
- system_timer->offset = dummy_gettimeoffset;
-#endif
system_timer->init();
}
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 2db43a5..2d040a4 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -23,14 +23,12 @@ choice
config ARCH_AT91RM9200
bool "AT91RM9200"
select CPU_ARM920T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_AT91_USART3
config ARCH_AT91SAM9260
bool "AT91SAM9260 or AT91SAM9XE"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_AT91_USART3
select HAVE_AT91_USART4
@@ -39,28 +37,24 @@ config ARCH_AT91SAM9260
config ARCH_AT91SAM9261
bool "AT91SAM9261"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_FB_ATMEL
config ARCH_AT91SAM9G10
bool "AT91SAM9G10"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_FB_ATMEL
config ARCH_AT91SAM9263
bool "AT91SAM9263"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_FB_ATMEL
config ARCH_AT91SAM9RL
bool "AT91SAM9RL"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_AT91_USART3
select HAVE_FB_ATMEL
@@ -68,7 +62,6 @@ config ARCH_AT91SAM9RL
config ARCH_AT91SAM9G20
bool "AT91SAM9G20"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_AT91_USART3
select HAVE_AT91_USART4
@@ -77,7 +70,6 @@ config ARCH_AT91SAM9G20
config ARCH_AT91SAM9G45
bool "AT91SAM9G45"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_AT91_USART3
select HAVE_FB_ATMEL
@@ -85,18 +77,17 @@ config ARCH_AT91SAM9G45
config ARCH_AT91CAP9
bool "AT91CAP9"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_FB_ATMEL
config ARCH_AT572D940HF
bool "AT572D940HF"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
config ARCH_AT91X40
bool "AT91x40"
+ select ARCH_USES_GETTIMEOFFSET
endchoice
--
1.6.0.4
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 3/3] time: Kill off CONFIG_GENERIC_TIME
2010-03-01 22:54 ` [PATCH 2/3] arm: Convert arm " john stultz
@ 2010-03-01 22:56 ` john stultz
2010-03-03 0:07 ` [PATCH 2/3] arm: Convert arm to arch_gettimeoffset() Andrew Morton
1 sibling, 0 replies; 5+ messages in thread
From: john stultz @ 2010-03-01 22:56 UTC (permalink / raw)
To: Thomas Gleixner
Cc: lkml, Andrew Morton, starvik, jesper.nilsson, Russell King
Now that all arches have been converted over to use generic time via
clocksources or arch_gettimeoffset(), we can remove the GENERIC_TIME
config option and simplify the generic code.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
---
Documentation/kernel-parameters.txt | 3 +-
arch/alpha/Kconfig | 4 --
arch/arm/Kconfig | 4 --
arch/avr32/Kconfig | 3 --
arch/blackfin/Kconfig | 3 --
arch/cris/Kconfig | 3 --
arch/frv/Kconfig | 4 --
arch/h8300/Kconfig | 4 --
arch/ia64/Kconfig | 4 --
arch/m32r/Kconfig | 3 --
arch/m68k/Kconfig | 3 --
arch/m68knommu/Kconfig | 4 --
arch/microblaze/Kconfig | 3 --
arch/mips/Kconfig | 4 --
arch/mn10300/Kconfig | 3 --
arch/parisc/Kconfig | 4 --
arch/powerpc/Kconfig | 3 --
arch/s390/Kconfig | 3 --
arch/sh/Kconfig | 3 --
arch/sparc/Kconfig | 3 --
arch/um/Kconfig.common | 4 --
arch/x86/Kconfig | 5 +--
arch/xtensa/Kconfig | 3 --
drivers/Makefile | 4 ++-
drivers/acpi/acpi_pad.c | 2 +-
drivers/acpi/processor_idle.c | 2 +-
drivers/clocksource/Kconfig | 2 +-
drivers/misc/Kconfig | 2 +-
kernel/time.c | 16 ----------
kernel/time/Kconfig | 4 +-
kernel/time/clocksource.c | 4 +-
kernel/time/timekeeping.c | 55 ++--------------------------------
kernel/trace/Kconfig | 4 +-
33 files changed, 19 insertions(+), 156 deletions(-)
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 8c666d8..87ea67b 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -71,7 +71,6 @@ parameter is applicable:
MTD MTD (Memory Technology Device) support is enabled.
NET Appropriate network support is enabled.
NUMA NUMA support is enabled.
- GENERIC_TIME The generic timeofday code is enabled.
NFS Appropriate NFS support is enabled.
OSS OSS sound support is enabled.
PV_OPS A paravirtualized kernel is enabled.
@@ -472,7 +471,7 @@ and is between 256 and 4096 characters. It is defined in the file
clocksource is not available, it defaults to PIT.
Format: { pit | tsc | cyclone | pmtmr }
- clocksource= [GENERIC_TIME] Override the default clocksource
+ clocksource= Override the default clocksource
Format: <string>
Override the default clocksource and use the clocksource
with the name specified.
diff --git a/arch/alpha/Kconfig b/arch/alpha/Kconfig
index bd7261e..b7dbb7f 100644
--- a/arch/alpha/Kconfig
+++ b/arch/alpha/Kconfig
@@ -46,10 +46,6 @@ config GENERIC_CALIBRATE_DELAY
bool
default y
-config GENERIC_TIME
- bool
- default y
-
config ARCH_USES_GETTIMEOFFSET
bool
default y
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index ff8e0b4..cec899f 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -40,10 +40,6 @@ config SYS_SUPPORTS_APM_EMULATION
config GENERIC_GPIO
bool
-config GENERIC_TIME
- bool
- default y
-
config ARCH_USES_GETTIMEOFFSET
bool
default n
diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig
index f2b3193..f515727 100644
--- a/arch/avr32/Kconfig
+++ b/arch/avr32/Kconfig
@@ -45,9 +45,6 @@ config GENERIC_IRQ_PROBE
config RWSEM_GENERIC_SPINLOCK
def_bool y
-config GENERIC_TIME
- def_bool y
-
config GENERIC_CLOCKEVENTS
def_bool y
diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index 53c1e1d..a891f0a 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -602,9 +602,6 @@ comment "Kernel Timer/Scheduler"
source kernel/Kconfig.hz
-config GENERIC_TIME
- def_bool y
-
config GENERIC_CLOCKEVENTS
bool "Generic clock events"
default y
diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig
index 059eac6..a668ce1 100644
--- a/arch/cris/Kconfig
+++ b/arch/cris/Kconfig
@@ -20,9 +20,6 @@ config RWSEM_GENERIC_SPINLOCK
config RWSEM_XCHGADD_ALGORITHM
bool
-config GENERIC_TIME
- def_bool y
-
config ARCH_USES_GETTIMEOFFSET
def_bool y
diff --git a/arch/frv/Kconfig b/arch/frv/Kconfig
index 4b5830b..16399bd 100644
--- a/arch/frv/Kconfig
+++ b/arch/frv/Kconfig
@@ -40,10 +40,6 @@ config GENERIC_HARDIRQS_NO__DO_IRQ
bool
default y
-config GENERIC_TIME
- bool
- default y
-
config TIME_LOW_RES
bool
default y
diff --git a/arch/h8300/Kconfig b/arch/h8300/Kconfig
index 53cc669..988b6ff 100644
--- a/arch/h8300/Kconfig
+++ b/arch/h8300/Kconfig
@@ -62,10 +62,6 @@ config GENERIC_CALIBRATE_DELAY
bool
default y
-config GENERIC_TIME
- bool
- default y
-
config GENERIC_BUG
bool
depends on BUG
diff --git a/arch/ia64/Kconfig b/arch/ia64/Kconfig
index 9a50d7d..177d0db 100644
--- a/arch/ia64/Kconfig
+++ b/arch/ia64/Kconfig
@@ -79,10 +79,6 @@ config GENERIC_CALIBRATE_DELAY
bool
default y
-config GENERIC_TIME
- bool
- default y
-
config GENERIC_TIME_VSYSCALL
bool
default y
diff --git a/arch/m32r/Kconfig b/arch/m32r/Kconfig
index 3a9319f..836abbb 100644
--- a/arch/m32r/Kconfig
+++ b/arch/m32r/Kconfig
@@ -44,9 +44,6 @@ config HZ
int
default 100
-config GENERIC_TIME
- def_bool y
-
config ARCH_USES_GETTIMEOFFSET
def_bool y
diff --git a/arch/m68k/Kconfig b/arch/m68k/Kconfig
index b5da298..ee3ed05 100644
--- a/arch/m68k/Kconfig
+++ b/arch/m68k/Kconfig
@@ -58,9 +58,6 @@ config HZ
int
default 100
-config GENERIC_TIME
- def_bool y
-
config ARCH_USES_GETTIMEOFFSET
def_bool y
diff --git a/arch/m68knommu/Kconfig b/arch/m68knommu/Kconfig
index 064f591..fb61afe 100644
--- a/arch/m68knommu/Kconfig
+++ b/arch/m68knommu/Kconfig
@@ -63,10 +63,6 @@ config GENERIC_CALIBRATE_DELAY
bool
default y
-config GENERIC_TIME
- bool
- default y
-
config GENERIC_CMOS_UPDATE
bool
default y
diff --git a/arch/microblaze/Kconfig b/arch/microblaze/Kconfig
index b008168..adbfd0c 100644
--- a/arch/microblaze/Kconfig
+++ b/arch/microblaze/Kconfig
@@ -46,9 +46,6 @@ config GENERIC_IRQ_PROBE
config GENERIC_CALIBRATE_DELAY
def_bool y
-config GENERIC_TIME
- def_bool y
-
config GENERIC_TIME_VSYSCALL
def_bool n
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index 591ca0c..1448600 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -731,10 +731,6 @@ config GENERIC_CLOCKEVENTS
bool
default y
-config GENERIC_TIME
- bool
- default y
-
config GENERIC_CMOS_UPDATE
bool
default y
diff --git a/arch/mn10300/Kconfig b/arch/mn10300/Kconfig
index 89faaca..fb2d232 100644
--- a/arch/mn10300/Kconfig
+++ b/arch/mn10300/Kconfig
@@ -43,9 +43,6 @@ config GENERIC_FIND_NEXT_BIT
config GENERIC_HWEIGHT
def_bool y
-config GENERIC_TIME
- def_bool y
-
config GENERIC_BUG
def_bool y
diff --git a/arch/parisc/Kconfig b/arch/parisc/Kconfig
index f388dc6..f7a4d3e 100644
--- a/arch/parisc/Kconfig
+++ b/arch/parisc/Kconfig
@@ -66,10 +66,6 @@ config GENERIC_CALIBRATE_DELAY
bool
default y
-config GENERIC_TIME
- bool
- default y
-
config TIME_LOW_RES
bool
depends on SMP
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 155d571..68d9df6 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -29,9 +29,6 @@ config MMU
config GENERIC_CMOS_UPDATE
def_bool y
-config GENERIC_TIME
- def_bool y
-
config GENERIC_TIME_VSYSCALL
def_bool y
diff --git a/arch/s390/Kconfig b/arch/s390/Kconfig
index 0d8cd9b..07ecd67 100644
--- a/arch/s390/Kconfig
+++ b/arch/s390/Kconfig
@@ -40,9 +40,6 @@ config ARCH_HAS_ILOG2_U64
config GENERIC_HWEIGHT
def_bool y
-config GENERIC_TIME
- def_bool y
-
config GENERIC_TIME_VSYSCALL
def_bool y
diff --git a/arch/sh/Kconfig b/arch/sh/Kconfig
index 05cef50..5819a92 100644
--- a/arch/sh/Kconfig
+++ b/arch/sh/Kconfig
@@ -97,9 +97,6 @@ config GENERIC_CALIBRATE_DELAY
config GENERIC_IOMAP
bool
-config GENERIC_TIME
- def_bool y
-
config GENERIC_CLOCKEVENTS
def_bool y
diff --git a/arch/sparc/Kconfig b/arch/sparc/Kconfig
index 4097f6a..49611c0 100644
--- a/arch/sparc/Kconfig
+++ b/arch/sparc/Kconfig
@@ -63,9 +63,6 @@ config BITS
default 32 if SPARC32
default 64 if SPARC64
-config GENERIC_TIME
- def_bool y
-
config ARCH_USES_GETTIMEOFFSET
bool
default y if SPARC32
diff --git a/arch/um/Kconfig.common b/arch/um/Kconfig.common
index 0d207e7..7c8e277 100644
--- a/arch/um/Kconfig.common
+++ b/arch/um/Kconfig.common
@@ -55,10 +55,6 @@ config GENERIC_BUG
default y
depends on BUG
-config GENERIC_TIME
- bool
- default y
-
config GENERIC_CLOCKEVENTS
bool
default y
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 0896008..014b8bc 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -67,9 +67,6 @@ config ARCH_DEFCONFIG
default "arch/x86/configs/i386_defconfig" if X86_32
default "arch/x86/configs/x86_64_defconfig" if X86_64
-config GENERIC_TIME
- def_bool y
-
config GENERIC_CMOS_UPDATE
def_bool y
@@ -2006,7 +2003,7 @@ config SCx200
config SCx200HR_TIMER
tristate "NatSemi SCx200 27MHz High-Resolution Timer Support"
- depends on SCx200 && GENERIC_TIME
+ depends on SCx200
default y
---help---
This driver provides a clocksource built upon the on-chip
diff --git a/arch/xtensa/Kconfig b/arch/xtensa/Kconfig
index ebe228d..0859bfd 100644
--- a/arch/xtensa/Kconfig
+++ b/arch/xtensa/Kconfig
@@ -48,9 +48,6 @@ config HZ
int
default 100
-config GENERIC_TIME
- def_bool y
-
source "init/Kconfig"
source "kernel/Kconfig.freezer"
diff --git a/drivers/Makefile b/drivers/Makefile
index 6ee53c7..a059f91 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -99,7 +99,9 @@ obj-$(CONFIG_SGI_SN) += sn/
obj-y += firmware/
obj-$(CONFIG_CRYPTO) += crypto/
obj-$(CONFIG_SUPERH) += sh/
-obj-$(CONFIG_GENERIC_TIME) += clocksource/
+ifndef CONFIG_ARCH_USES_GETTIMEOFFSET
+obj-y += clocksource/
+endif
obj-$(CONFIG_DMA_ENGINE) += dma/
obj-$(CONFIG_DCA) += dca/
obj-$(CONFIG_HID) += hid/
diff --git a/drivers/acpi/acpi_pad.c b/drivers/acpi/acpi_pad.c
index 7e52295..d144710 100644
--- a/drivers/acpi/acpi_pad.c
+++ b/drivers/acpi/acpi_pad.c
@@ -73,7 +73,7 @@ static void power_saving_mwait_init(void)
for_each_online_cpu(i)
clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ON, &i);
-#if defined(CONFIG_GENERIC_TIME) && defined(CONFIG_X86)
+#if defined(CONFIG_X86)
switch (boot_cpu_data.x86_vendor) {
case X86_VENDOR_AMD:
case X86_VENDOR_INTEL:
diff --git a/drivers/acpi/processor_idle.c b/drivers/acpi/processor_idle.c
index 37dfce7..60efa42 100644
--- a/drivers/acpi/processor_idle.c
+++ b/drivers/acpi/processor_idle.c
@@ -258,7 +258,7 @@ int acpi_processor_resume(struct acpi_device * device)
return 0;
}
-#if defined (CONFIG_GENERIC_TIME) && defined (CONFIG_X86)
+#if defined(CONFIG_X86)
static void tsc_check_state(int state)
{
switch (boot_cpu_data.x86_vendor) {
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index 08f726c..f8d1d73 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -1,6 +1,6 @@
config CS5535_CLOCK_EVENT_SRC
tristate "CS5535/CS5536 high-res timer (MFGPT) events"
- depends on GENERIC_TIME && GENERIC_CLOCKEVENTS && CS5535_MFGPT
+ depends on GENERIC_CLOCKEVENTS && CS5535_MFGPT
help
This driver provides a clock event source based on the MFGPT
timer(s) in the CS5535 and CS5536 companion chips.
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index e3551d2..9da7433 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -46,7 +46,7 @@ config ATMEL_TCLIB
config ATMEL_TCB_CLKSRC
bool "TC Block Clocksource"
- depends on ATMEL_TCLIB && GENERIC_TIME
+ depends on ATMEL_TCLIB
default y
help
Select this to get a high precision clocksource based on a
diff --git a/kernel/time.c b/kernel/time.c
index 8047980..19f7b37 100644
--- a/kernel/time.c
+++ b/kernel/time.c
@@ -302,22 +302,6 @@ struct timespec timespec_trunc(struct timespec t, unsigned gran)
}
EXPORT_SYMBOL(timespec_trunc);
-#ifndef CONFIG_GENERIC_TIME
-/*
- * Simulate gettimeofday using do_gettimeofday which only allows a timeval
- * and therefore only yields usec accuracy
- */
-void getnstimeofday(struct timespec *tv)
-{
- struct timeval x;
-
- do_gettimeofday(&x);
- tv->tv_sec = x.tv_sec;
- tv->tv_nsec = x.tv_usec * NSEC_PER_USEC;
-}
-EXPORT_SYMBOL_GPL(getnstimeofday);
-#endif
-
/* Converts Gregorian date to seconds since 1970-01-01 00:00:00.
* Assumes input in normal date format, i.e. 1980-12-31 23:59:59
* => year=1980, mon=12, day=31, hour=23, min=59, sec=59.
diff --git a/kernel/time/Kconfig b/kernel/time/Kconfig
index 95ed429..f06a8a3 100644
--- a/kernel/time/Kconfig
+++ b/kernel/time/Kconfig
@@ -6,7 +6,7 @@ config TICK_ONESHOT
config NO_HZ
bool "Tickless System (Dynamic Ticks)"
- depends on GENERIC_TIME && GENERIC_CLOCKEVENTS
+ depends on !ARCH_USES_GETTIMEOFFSET && GENERIC_CLOCKEVENTS
select TICK_ONESHOT
help
This option enables a tickless system: timer interrupts will
@@ -15,7 +15,7 @@ config NO_HZ
config HIGH_RES_TIMERS
bool "High Resolution Timer Support"
- depends on GENERIC_TIME && GENERIC_CLOCKEVENTS
+ depends on !ARCH_USES_GETTIMEOFFSET && GENERIC_CLOCKEVENTS
select TICK_ONESHOT
help
This option enables high resolution timer support. If your
diff --git a/kernel/time/clocksource.c b/kernel/time/clocksource.c
index 1f663d2..208d1db 100644
--- a/kernel/time/clocksource.c
+++ b/kernel/time/clocksource.c
@@ -531,7 +531,7 @@ static u64 clocksource_max_deferment(struct clocksource *cs)
return max_nsecs - (max_nsecs >> 5);
}
-#ifdef CONFIG_GENERIC_TIME
+#ifndef CONFIG_ARCH_USES_GETTIMEOFFSET
/**
* clocksource_select - Select the best clocksource available
@@ -577,7 +577,7 @@ static void clocksource_select(void)
}
}
-#else /* CONFIG_GENERIC_TIME */
+#else /* !CONFIG_ARCH_USES_GETTIMEOFFSET */
static inline void clocksource_select(void) { }
diff --git a/kernel/time/timekeeping.c b/kernel/time/timekeeping.c
index 1673637..e81d319 100644
--- a/kernel/time/timekeeping.c
+++ b/kernel/time/timekeeping.c
@@ -180,8 +180,6 @@ void timekeeping_leap_insert(int leapsecond)
update_vsyscall(&xtime, timekeeper.clock, timekeeper.mult);
}
-#ifdef CONFIG_GENERIC_TIME
-
/**
* timekeeping_forward_now - update clock to the current time
*
@@ -385,52 +383,6 @@ void timekeeping_notify(struct clocksource *clock)
tick_clock_notify();
}
-#else /* GENERIC_TIME */
-
-static inline void timekeeping_forward_now(void) { }
-
-/**
- * ktime_get - get the monotonic time in ktime_t format
- *
- * returns the time in ktime_t format
- */
-ktime_t ktime_get(void)
-{
- struct timespec now;
-
- ktime_get_ts(&now);
-
- return timespec_to_ktime(now);
-}
-EXPORT_SYMBOL_GPL(ktime_get);
-
-/**
- * ktime_get_ts - get the monotonic clock in timespec format
- * @ts: pointer to timespec variable
- *
- * The function calculates the monotonic clock from the realtime
- * clock and the wall_to_monotonic offset and stores the result
- * in normalized timespec format in the variable pointed to by @ts.
- */
-void ktime_get_ts(struct timespec *ts)
-{
- struct timespec tomono;
- unsigned long seq;
-
- do {
- seq = read_seqbegin(&xtime_lock);
- getnstimeofday(ts);
- tomono = wall_to_monotonic;
-
- } while (read_seqretry(&xtime_lock, seq));
-
- set_normalized_timespec(ts, ts->tv_sec + tomono.tv_sec,
- ts->tv_nsec + tomono.tv_nsec);
-}
-EXPORT_SYMBOL_GPL(ktime_get_ts);
-
-#endif /* !GENERIC_TIME */
-
/**
* ktime_get_real - get the real (wall-) time in ktime_t format
*
@@ -796,10 +748,11 @@ void update_wall_time(void)
return;
clock = timekeeper.clock;
-#ifdef CONFIG_GENERIC_TIME
- offset = (clock->read(clock) - clock->cycle_last) & clock->mask;
-#else
+
+#ifdef CONFIG_ARCH_USES_GETTIMEOFFSET
offset = timekeeper.cycle_interval;
+#else
+ offset = (clock->read(clock) - clock->cycle_last) & clock->mask;
#endif
timekeeper.xtime_nsec = (s64)xtime.tv_nsec << timekeeper.shift;
diff --git a/kernel/trace/Kconfig b/kernel/trace/Kconfig
index 13e13d4..8930ba3 100644
--- a/kernel/trace/Kconfig
+++ b/kernel/trace/Kconfig
@@ -156,7 +156,7 @@ config IRQSOFF_TRACER
bool "Interrupts-off Latency Tracer"
default n
depends on TRACE_IRQFLAGS_SUPPORT
- depends on GENERIC_TIME
+ depends on !ARCH_USES_GETTIMEOFFSET
select TRACE_IRQFLAGS
select GENERIC_TRACER
select TRACER_MAX_TRACE
@@ -178,7 +178,7 @@ config IRQSOFF_TRACER
config PREEMPT_TRACER
bool "Preemption-off Latency Tracer"
default n
- depends on GENERIC_TIME
+ depends on !ARCH_USES_GETTIMEOFFSET
depends on PREEMPT
select GENERIC_TRACER
select TRACER_MAX_TRACE
--
1.6.0.4
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH 2/3] arm: Convert arm to arch_gettimeoffset()
2010-03-01 22:54 ` [PATCH 2/3] arm: Convert arm " john stultz
2010-03-01 22:56 ` [PATCH 3/3] time: Kill off CONFIG_GENERIC_TIME john stultz
@ 2010-03-03 0:07 ` Andrew Morton
2010-03-03 0:28 ` john stultz
1 sibling, 1 reply; 5+ messages in thread
From: Andrew Morton @ 2010-03-03 0:07 UTC (permalink / raw)
To: john stultz; +Cc: Russell King, lkml, Thomas Gleixner, linux-arm-kernel
On Mon, 01 Mar 2010 14:54:14 -0800
john stultz <johnstul@us.ibm.com> wrote:
> This patch converts arm to use GENERIC_TIME via the arch_getoffset()
> infrastructure, reducing the amount of arch specific code we need to
> maintain.
It runs afoul of the pending changes in linux-next:
patching file arch/arm/Kconfig
Hunk #3 FAILED at 240.
Hunk #4 FAILED at 250.
Hunk #5 FAILED at 262.
Hunk #6 succeeded at 293 (offset 21 lines).
Hunk #7 succeeded at 301 (offset 21 lines).
Hunk #8 succeeded at 310 (offset 21 lines).
Hunk #9 succeeded at 319 (offset 21 lines).
Hunk #10 succeeded at 336 (offset 21 lines).
Hunk #11 FAILED at 344.
Hunk #12 succeeded at 364 (offset 20 lines).
Hunk #13 succeeded at 375 (offset 20 lines).
Hunk #14 succeeded at 382 (offset 20 lines).
Hunk #15 succeeded at 393 (offset 20 lines).
Hunk #16 succeeded at 407 (offset 20 lines).
Hunk #17 succeeded at 419 (offset 20 lines).
Hunk #18 succeeded at 432 (offset 20 lines).
Hunk #19 succeeded at 441 (offset 20 lines).
Hunk #20 succeeded at 450 (offset 20 lines).
Hunk #21 succeeded at 459 (offset 20 lines).
Hunk #22 succeeded at 468 (offset 20 lines).
Hunk #23 succeeded at 484 (offset 20 lines).
Hunk #24 succeeded at 495 (offset 20 lines).
Hunk #25 succeeded at 504 (offset 20 lines).
Hunk #26 succeeded at 515 (offset 20 lines).
Hunk #27 succeeded at 528 (offset 20 lines).
Hunk #28 succeeded at 542 (offset 20 lines).
Hunk #29 succeeded at 553 (offset 20 lines).
Hunk #30 succeeded at 562 (offset 20 lines).
Hunk #31 succeeded at 577 (offset 20 lines).
Hunk #32 succeeded at 601 (offset 20 lines).
Hunk #33 succeeded at 614 (offset 20 lines).
Hunk #34 FAILED at 623.
Hunk #35 succeeded at 646 (offset 26 lines).
Hunk #36 succeeded at 660 (offset 26 lines).
Hunk #37 succeeded at 672 (offset 26 lines).
Hunk #38 FAILED at 682.
Hunk #39 succeeded at 743 (offset 66 lines).
Hunk #40 succeeded at 753 (offset 66 lines).
Hunk #41 succeeded at 767 (offset 66 lines).
Hunk #42 succeeded at 777 (offset 66 lines).
Hunk #43 succeeded at 795 (offset 66 lines).
Hunk #44 succeeded at 806 (offset 66 lines).
Hunk #45 succeeded at 815 (offset 66 lines).
Hunk #46 succeeded at 944 (offset 73 lines).
6 out of 46 hunks FAILED -- saving rejects to file arch/arm/Kconfig.rej
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 2/3] arm: Convert arm to arch_gettimeoffset()
2010-03-03 0:07 ` [PATCH 2/3] arm: Convert arm to arch_gettimeoffset() Andrew Morton
@ 2010-03-03 0:28 ` john stultz
0 siblings, 0 replies; 5+ messages in thread
From: john stultz @ 2010-03-03 0:28 UTC (permalink / raw)
To: Andrew Morton; +Cc: Russell King, lkml, Thomas Gleixner, linux-arm-kernel
On Tue, 2010-03-02 at 16:07 -0800, Andrew Morton wrote:
> On Mon, 01 Mar 2010 14:54:14 -0800
> john stultz <johnstul@us.ibm.com> wrote:
>
> > This patch converts arm to use GENERIC_TIME via the arch_getoffset()
> > infrastructure, reducing the amount of arch specific code we need to
> > maintain.
>
> It runs afoul of the pending changes in linux-next:
Sigh. Yea, there's a lot of simple changes in Kconfig, and as long as
this stays out of the upstream tree, its going to be a bit of a
treadmill.
Russell, any help here would be appreciated!
Here's the patch against linux-next.
thanks
-john
This patch converts arm to use GENERIC_TIME via the arch_getoffset()
infrastructure, reducing the amount of arch specific code we need to
maintain.
The arm architecture is one of the last 2 arches that need to be
converted.
This patch applies on top the current -next tree
I've taken my best swing at converting this, but I'm not 100% confident
I got it right. My cross-compiler is now out of date (gcc4.2) so I
wasn't able to check if it compiled. Any assistance from arch
maintainers or testers to get this merged would be great.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index adbbaf3..6ebe0cd 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -42,6 +42,11 @@ config GENERIC_GPIO
config GENERIC_TIME
bool
+ default y
+
+config ARCH_USES_GETTIMEOFFSET
+ bool
+ default n
config GENERIC_CLOCKEVENTS
bool
@@ -224,6 +229,7 @@ config ARCH_AAEC2000
select CPU_ARM920T
select ARM_AMBA
select HAVE_CLK
+ select ARCH_USES_GETTIMEOFFSET
help
This enables support for systems based on the Agilent AAEC-2000
@@ -234,7 +240,6 @@ config ARCH_INTEGRATOR
select HAVE_CLK
select COMMON_CLKDEV
select ICST
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select PLAT_VERSATILE
help
@@ -246,7 +251,6 @@ config ARCH_REALVIEW
select HAVE_CLK
select COMMON_CLKDEV
select ICST
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select ARCH_WANT_OPTIONAL_GPIOLIB
select PLAT_VERSATILE
@@ -261,7 +265,6 @@ config ARCH_VERSATILE
select HAVE_CLK
select COMMON_CLKDEV
select ICST
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select ARCH_WANT_OPTIONAL_GPIOLIB
select PLAT_VERSATILE
@@ -276,7 +279,6 @@ config ARCH_VEXPRESS
select ARM_TIMER_SP804
select COMMON_CLKDEV
select GENERIC_CLOCKEVENTS
- select GENERIC_TIME
select HAVE_CLK
select ICST
select PLAT_VERSATILE
@@ -288,6 +290,7 @@ config ARCH_AT91
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
select HAVE_CLK
+ select ARCH_USES_GETTIMEOFFSET
help
This enables support for systems based on the Atmel AT91RM9200,
AT91SAM9 and AT91CAP9 processors.
@@ -295,6 +298,7 @@ config ARCH_AT91
config ARCH_CLPS711X
bool "Cirrus Logic CLPS711x/EP721x-based"
select CPU_ARM720T
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Cirrus Logic 711x/721x based boards.
@@ -303,6 +307,7 @@ config ARCH_GEMINI
select CPU_FA526
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
+ select ARCH_USES_GETTIMEOFFSET
help
Support for the Cortina Systems Gemini family SoCs
@@ -311,6 +316,7 @@ config ARCH_EBSA110
select CPU_SA110
select ISA
select NO_IOPORT
+ select ARCH_USES_GETTIMEOFFSET
help
This is an evaluation board for the StrongARM processor available
from Digital. It has limited hardware on-board, including an
@@ -327,6 +333,7 @@ config ARCH_EP93XX
select COMMON_CLKDEV
select ARCH_REQUIRE_GPIOLIB
select ARCH_HAS_HOLES_MEMORYMODEL
+ select ARCH_USES_GETTIMEOFFSET
help
This enables support for the Cirrus EP93xx series of CPUs.
@@ -334,13 +341,13 @@ config ARCH_FOOTBRIDGE
bool "FootBridge"
select CPU_SA110
select FOOTBRIDGE
+ select ARCH_USES_GETTIMEOFFSET
help
Support for systems based on the DC21285 companion chip
("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
config ARCH_MXC
bool "Freescale MXC/iMX-based"
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select ARCH_REQUIRE_GPIOLIB
select HAVE_CLK
@@ -354,7 +361,6 @@ config ARCH_STMP3XXX
select HAVE_CLK
select COMMON_CLKDEV
select ARCH_REQUIRE_GPIOLIB
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select GENERIC_GPIO
select USB_ARCH_HAS_EHCI
@@ -366,7 +372,6 @@ config ARCH_NETX
select CPU_ARM926T
select ARM_VIC
select GENERIC_CLOCKEVENTS
- select GENERIC_TIME
help
This enables support for systems based on the Hilscher NetX Soc
@@ -374,6 +379,7 @@ config ARCH_H720X
bool "Hynix HMS720x-based"
select CPU_ARM720T
select ISA_DMA_API
+ select ARCH_USES_GETTIMEOFFSET
help
This enables support for systems based on the Hynix HMS720x
@@ -384,7 +390,6 @@ config ARCH_NOMADIK
select CPU_ARM926T
select HAVE_CLK
select COMMON_CLKDEV
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
@@ -399,6 +404,7 @@ config ARCH_IOP13XX
select PCI
select ARCH_SUPPORTS_MSI
select VMSPLIT_1G
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Intel's IOP13XX (XScale) family of processors.
@@ -410,6 +416,7 @@ config ARCH_IOP32X
select PCI
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Intel's 80219 and IOP32X (XScale) family of
processors.
@@ -422,6 +429,7 @@ config ARCH_IOP33X
select PCI
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Intel's IOP33X (XScale) family of processors.
@@ -430,6 +438,7 @@ config ARCH_IXP23XX
depends on MMU
select CPU_XSC3
select PCI
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Intel's IXP23xx (XScale) family of processors.
@@ -438,6 +447,7 @@ config ARCH_IXP2000
depends on MMU
select CPU_XSCALE
select PCI
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Intel's IXP2400/2800 (XScale) family of processors.
@@ -446,7 +456,6 @@ config ARCH_IXP4XX
depends on MMU
select CPU_XSCALE
select GENERIC_GPIO
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select DMABOUNCE if PCI
help
@@ -456,6 +465,7 @@ config ARCH_L7200
bool "LinkUp-L7200"
select CPU_ARM720T
select FIQ
+ select ARCH_USES_GETTIMEOFFSET
help
Say Y here if you intend to run this kernel on a LinkUp Systems
L7200 Software Development Board which uses an ARM720T processor.
@@ -471,7 +481,6 @@ config ARCH_DOVE
select PCI
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select PLAT_ORION
help
@@ -483,7 +492,6 @@ config ARCH_KIRKWOOD
select PCI
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select PLAT_ORION
help
@@ -493,7 +501,6 @@ config ARCH_KIRKWOOD
config ARCH_LOKI
bool "Marvell Loki (88RC8480)"
select CPU_FEROCEON
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select PLAT_ORION
help
@@ -505,7 +512,6 @@ config ARCH_MV78XX0
select PCI
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select PLAT_ORION
help
@@ -519,7 +525,6 @@ config ARCH_ORION5X
select PCI
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select PLAT_ORION
help
@@ -534,7 +539,6 @@ config ARCH_MMP
select ARCH_REQUIRE_GPIOLIB
select HAVE_CLK
select COMMON_CLKDEV
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select TICK_ONESHOT
select PLAT_PXA
@@ -546,6 +550,7 @@ config ARCH_KS8695
select CPU_ARM922T
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
+ select ARCH_USES_GETTIMEOFFSET
help
Support for Micrel/Kendin KS8695 "Centaur" (ARM922T) based
System-on-Chip devices.
@@ -554,7 +559,6 @@ config ARCH_NS9XXX
bool "NetSilicon NS9xxx"
select CPU_ARM926T
select GENERIC_GPIO
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_CLK
help
@@ -570,7 +574,6 @@ config ARCH_W90X900
select GENERIC_GPIO
select HAVE_CLK
select COMMON_CLKDEV
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
help
Support for Nuvoton (Winbond logic dept.) ARM9 processor,
@@ -595,6 +598,7 @@ config ARCH_PNX4008
select CPU_ARM926T
select HAVE_CLK
select COMMON_CLKDEV
+ select ARCH_USES_GETTIMEOFFSET
help
This enables support for Philips PNX4008 mobile platform.
@@ -607,7 +611,6 @@ config ARCH_PXA
select HAVE_CLK
select COMMON_CLKDEV
select ARCH_REQUIRE_GPIOLIB
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select TICK_ONESHOT
select PLAT_PXA
@@ -617,7 +620,6 @@ config ARCH_PXA
config ARCH_MSM
bool "Qualcomm MSM"
select GENERIC_GPIO
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
help
Support for Qualcomm MSM/QSD based systems. This runs on the
@@ -641,6 +643,7 @@ config ARCH_RPC
select ISA_DMA_API
select NO_IOPORT
select ARCH_SPARSEMEM_ENABLE
+ select ARCH_USES_GETTIMEOFFSET
help
On the Acorn Risc-PC, Linux can support the internal IDE disk and
CD-ROM interface, serial and parallel port, and the floppy drive.
@@ -654,7 +657,6 @@ config ARCH_SA1100
select ARCH_HAS_CPUFREQ
select CPU_FREQ
select GENERIC_GPIO
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_CLK
select TICK_ONESHOT
@@ -667,6 +669,7 @@ config ARCH_S3C2410
select GENERIC_GPIO
select ARCH_HAS_CPUFREQ
select HAVE_CLK
+ select ARCH_USES_GETTIMEOFFSET
help
Samsung S3C2410X CPU based systems, such as the Simtec Electronics
BAST (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or
@@ -679,6 +682,7 @@ config ARCH_S3C64XX
select GENERIC_GPIO
select ARM_VIC
select HAVE_CLK
+ select ARCH_USES_GETTIMEOFFSET
select NO_IOPORT
select ARCH_HAS_CPUFREQ
select ARCH_REQUIRE_GPIOLIB
@@ -736,6 +740,7 @@ config ARCH_SHARK
select ISA_DMA
select ZONE_DMA
select PCI
+ select ARCH_USES_GETTIMEOFFSET
help
Support for the StrongARM based Digital DNARD machine, also known
as "Shark" (<http://www.shark-linux.de/shark.html>).
@@ -745,6 +750,7 @@ config ARCH_LH7A40X
select CPU_ARM922T
select ARCH_DISCONTIGMEM_ENABLE if !LH7A40X_CONTIGMEM
select ARCH_SPARSEMEM_ENABLE if !LH7A40X_CONTIGMEM
+ select ARCH_USES_GETTIMEOFFSET
help
Say Y here for systems based on one of the Sharp LH7A40X
System on a Chip processors. These CPUs include an ARM922T
@@ -758,7 +764,6 @@ config ARCH_U300
select HAVE_TCM
select ARM_AMBA
select ARM_VIC
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_CLK
select COMMON_CLKDEV
@@ -769,7 +774,6 @@ config ARCH_U300
config ARCH_DAVINCI
bool "TI DaVinci"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
@@ -788,7 +792,6 @@ config ARCH_OMAP
select HAVE_CLK
select ARCH_REQUIRE_GPIOLIB
select ARCH_HAS_CPUFREQ
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select ARCH_HAS_HOLES_MEMORYMODEL
help
@@ -800,7 +803,6 @@ config ARCH_BCMRING
select CPU_V6
select ARM_AMBA
select COMMON_CLKDEV
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select ARCH_WANT_OPTIONAL_GPIOLIB
help
@@ -810,7 +812,6 @@ config ARCH_U8500
bool "ST-Ericsson U8500 Series"
select CPU_V7
select ARM_AMBA
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select COMMON_CLKDEV
help
@@ -940,7 +941,6 @@ config ARCH_ACORN
config PLAT_IOP
bool
select GENERIC_CLOCKEVENTS
- select GENERIC_TIME
config PLAT_ORION
bool
diff --git a/arch/arm/include/asm/mach/time.h b/arch/arm/include/asm/mach/time.h
index 8bffc3f..35d408f 100644
--- a/arch/arm/include/asm/mach/time.h
+++ b/arch/arm/include/asm/mach/time.h
@@ -38,7 +38,7 @@ struct sys_timer {
void (*init)(void);
void (*suspend)(void);
void (*resume)(void);
-#ifndef CONFIG_GENERIC_TIME
+#ifdef CONFIG_ARCH_USES_GETTIMEOFFSET
unsigned long (*offset)(void);
#endif
};
diff --git a/arch/arm/kernel/time.c b/arch/arm/kernel/time.c
index 2875380..38c261f 100644
--- a/arch/arm/kernel/time.c
+++ b/arch/arm/kernel/time.c
@@ -72,12 +72,15 @@ unsigned long profile_pc(struct pt_regs *regs)
EXPORT_SYMBOL(profile_pc);
#endif
-#ifndef CONFIG_GENERIC_TIME
-static unsigned long dummy_gettimeoffset(void)
+#ifdef CONFIG_ARCH_USES_GETTIMEOFFSET
+u32 arch_gettimeoffset(void)
{
+ if (system_timer->offset != NULL)
+ return system_timer->offset() * 1000;
+
return 0;
}
-#endif
+#endif /* CONFIG_ARCH_USES_GETTIMEOFFSET */
#ifdef CONFIG_LEDS_TIMER
static inline void do_leds(void)
@@ -93,63 +96,6 @@ static inline void do_leds(void)
#define do_leds()
#endif
-#ifndef CONFIG_GENERIC_TIME
-void do_gettimeofday(struct timeval *tv)
-{
- unsigned long flags;
- unsigned long seq;
- unsigned long usec, sec;
-
- do {
- seq = read_seqbegin_irqsave(&xtime_lock, flags);
- usec = system_timer->offset();
- sec = xtime.tv_sec;
- usec += xtime.tv_nsec / 1000;
- } while (read_seqretry_irqrestore(&xtime_lock, seq, flags));
-
- /* usec may have gone up a lot: be safe */
- while (usec >= 1000000) {
- usec -= 1000000;
- sec++;
- }
-
- tv->tv_sec = sec;
- tv->tv_usec = usec;
-}
-
-EXPORT_SYMBOL(do_gettimeofday);
-
-int do_settimeofday(struct timespec *tv)
-{
- time_t wtm_sec, sec = tv->tv_sec;
- long wtm_nsec, nsec = tv->tv_nsec;
-
- if ((unsigned long)tv->tv_nsec >= NSEC_PER_SEC)
- return -EINVAL;
-
- write_seqlock_irq(&xtime_lock);
- /*
- * This is revolting. We need to set "xtime" correctly. However, the
- * value in this location is the value at the most recent update of
- * wall time. Discover what correction gettimeofday() would have
- * done, and then undo it!
- */
- nsec -= system_timer->offset() * NSEC_PER_USEC;
-
- wtm_sec = wall_to_monotonic.tv_sec + (xtime.tv_sec - sec);
- wtm_nsec = wall_to_monotonic.tv_nsec + (xtime.tv_nsec - nsec);
-
- set_normalized_timespec(&xtime, sec, nsec);
- set_normalized_timespec(&wall_to_monotonic, wtm_sec, wtm_nsec);
-
- ntp_clear();
- write_sequnlock_irq(&xtime_lock);
- clock_was_set();
- return 0;
-}
-
-EXPORT_SYMBOL(do_settimeofday);
-#endif /* !CONFIG_GENERIC_TIME */
#ifndef CONFIG_GENERIC_CLOCKEVENTS
/*
@@ -214,10 +160,6 @@ device_initcall(timer_init_sysfs);
void __init time_init(void)
{
-#ifndef CONFIG_GENERIC_TIME
- if (system_timer->offset == NULL)
- system_timer->offset = dummy_gettimeoffset;
-#endif
system_timer->init();
}
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 2db43a5..2d040a4 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -23,14 +23,12 @@ choice
config ARCH_AT91RM9200
bool "AT91RM9200"
select CPU_ARM920T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_AT91_USART3
config ARCH_AT91SAM9260
bool "AT91SAM9260 or AT91SAM9XE"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_AT91_USART3
select HAVE_AT91_USART4
@@ -39,28 +37,24 @@ config ARCH_AT91SAM9260
config ARCH_AT91SAM9261
bool "AT91SAM9261"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_FB_ATMEL
config ARCH_AT91SAM9G10
bool "AT91SAM9G10"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_FB_ATMEL
config ARCH_AT91SAM9263
bool "AT91SAM9263"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_FB_ATMEL
config ARCH_AT91SAM9RL
bool "AT91SAM9RL"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_AT91_USART3
select HAVE_FB_ATMEL
@@ -68,7 +62,6 @@ config ARCH_AT91SAM9RL
config ARCH_AT91SAM9G20
bool "AT91SAM9G20"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_AT91_USART3
select HAVE_AT91_USART4
@@ -77,7 +70,6 @@ config ARCH_AT91SAM9G20
config ARCH_AT91SAM9G45
bool "AT91SAM9G45"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_AT91_USART3
select HAVE_FB_ATMEL
@@ -85,18 +77,17 @@ config ARCH_AT91SAM9G45
config ARCH_AT91CAP9
bool "AT91CAP9"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select HAVE_FB_ATMEL
config ARCH_AT572D940HF
bool "AT572D940HF"
select CPU_ARM926T
- select GENERIC_TIME
select GENERIC_CLOCKEVENTS
config ARCH_AT91X40
bool "AT91x40"
+ select ARCH_USES_GETTIMEOFFSET
endchoice
^ permalink raw reply related [flat|nested] 5+ messages in thread
end of thread, other threads:[~2010-03-03 0:28 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-03-01 22:51 [PATCH 1/3] Convert cris to arch_gettimeoffset() john stultz
2010-03-01 22:54 ` [PATCH 2/3] arm: Convert arm " john stultz
2010-03-01 22:56 ` [PATCH 3/3] time: Kill off CONFIG_GENERIC_TIME john stultz
2010-03-03 0:07 ` [PATCH 2/3] arm: Convert arm to arch_gettimeoffset() Andrew Morton
2010-03-03 0:28 ` john stultz
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).