* [PATCH v8 0/5] USB: LPC32xx device tree related OHCI and UDC patch series
@ 2012-04-29 14:47 Roland Stigge
2012-04-29 14:47 ` [PATCH v8 1/5] ohci-nxp: Driver cleanup Roland Stigge
` (5 more replies)
0 siblings, 6 replies; 7+ messages in thread
From: Roland Stigge @ 2012-04-29 14:47 UTC (permalink / raw)
To: gregkh, linux-usb, linux-kernel, kevin.wells, srinivas.bakki,
stern, linux-arm-kernel, arnd, grant.likely, rob.herring,
devicetree-discuss
Cc: Roland Stigge
This series collects the pending LPC32xx patches in one series and forward
ports it onto
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-next
There are no other changes since last post.
Roland Stigge (5):
ohci-nxp: Driver cleanup
ohci-nxp: Device tree support
USB: Add driver for NXP ISP1301 USB transceiver
USB: gadget driver for LPC32xx
USB: ohci-nxp: Use isp1301 driver
Documentation/devicetree/bindings/usb/isp1301.txt | 25 +
.../devicetree/bindings/usb/lpc32xx-udc.txt | 28 +
Documentation/devicetree/bindings/usb/ohci-nxp.txt | 24 +
drivers/usb/Kconfig | 2 +
drivers/usb/Makefile | 1 +
drivers/usb/gadget/Kconfig | 11 +
drivers/usb/gadget/Makefile | 1 +
drivers/usb/gadget/gadget_chips.h | 3 +
drivers/usb/gadget/lpc32xx_udc.c | 3538 ++++++++++++++++++++
drivers/usb/host/Kconfig | 1 +
drivers/usb/host/ohci-nxp.c | 165 +-
drivers/usb/phy/Kconfig | 17 +
drivers/usb/phy/Makefile | 7 +
drivers/usb/phy/isp1301.c | 77 +
include/linux/usb/isp1301.h | 80 +
15 files changed, 3861 insertions(+), 119 deletions(-)
create mode 100644 Documentation/devicetree/bindings/usb/isp1301.txt
create mode 100644 Documentation/devicetree/bindings/usb/lpc32xx-udc.txt
create mode 100644 Documentation/devicetree/bindings/usb/ohci-nxp.txt
create mode 100644 drivers/usb/gadget/lpc32xx_udc.c
create mode 100644 drivers/usb/phy/Kconfig
create mode 100644 drivers/usb/phy/Makefile
create mode 100644 drivers/usb/phy/isp1301.c
create mode 100644 include/linux/usb/isp1301.h
--
1.7.9
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v8 1/5] ohci-nxp: Driver cleanup
2012-04-29 14:47 [PATCH v8 0/5] USB: LPC32xx device tree related OHCI and UDC patch series Roland Stigge
@ 2012-04-29 14:47 ` Roland Stigge
2012-04-29 14:47 ` [PATCH v8 2/5] ohci-nxp: Device tree support Roland Stigge
` (4 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Roland Stigge @ 2012-04-29 14:47 UTC (permalink / raw)
To: gregkh, linux-usb, linux-kernel, kevin.wells, srinivas.bakki,
stern, linux-arm-kernel, arnd, grant.likely, rob.herring,
devicetree-discuss
Cc: Roland Stigge
Cleanup for ohci-nxp.c:
* Cleanup of resource handling (mem and irq), use devm_request_and_ioremap()
* Use DMA_BIT_MASK()
* Don't remove __devinit
* Removed obsolete gpio.h include
* More consistent bit access symbols
* Removed unused extern declaration ocpi_enable()
* Added error handling on i2c_get_adapter()
* Whitespace cleanup
Signed-off-by: Roland Stigge <stigge@antcom.de>
---
drivers/usb/host/ohci-nxp.c | 44 +++++++++++++++++++++++++-----------------
1 files changed, 26 insertions(+), 18 deletions(-)
diff --git a/drivers/usb/host/ohci-nxp.c b/drivers/usb/host/ohci-nxp.c
index d02abc3..63261f7 100644
--- a/drivers/usb/host/ohci-nxp.c
+++ b/drivers/usb/host/ohci-nxp.c
@@ -29,7 +29,6 @@
#include <mach/platform.h>
#include <mach/irqs.h>
-#include <asm/gpio.h>
#define USB_CONFIG_BASE 0x31020000
#define PWRMAN_BASE 0x40004000
@@ -38,7 +37,9 @@
/* USB_CTRL bit defines */
#define USB_SLAVE_HCLK_EN (1 << 24)
+#define USB_DEV_NEED_CLK_EN (1 << 22)
#define USB_HOST_NEED_CLK_EN (1 << 21)
+#define PAD_CONTROL_LAST_DRIVEN (1 << 19)
#define USB_OTG_CLK_CTRL IO_ADDRESS(USB_CONFIG_BASE + 0xFF4)
#define USB_OTG_CLK_STAT IO_ADDRESS(USB_CONFIG_BASE + 0xFF8)
@@ -117,7 +118,6 @@ static struct i2c_driver isp1301_driver;
static struct i2c_client *isp1301_i2c_client;
extern int usb_disabled(void);
-extern int ocpi_enable(void);
static struct clk *usb_clk;
@@ -220,7 +220,7 @@ static void isp1301_configure_lpc32xx(void)
ISP1301_I2C_INTERRUPT_RISING | ISP1301_I2C_REG_CLEAR_ADDR, ~0);
/* Enable usb_need_clk clock after transceiver is initialized */
- __raw_writel((__raw_readl(USB_CTRL) | (1 << 22)), USB_CTRL);
+ __raw_writel(__raw_readl(USB_CTRL) | USB_HOST_NEED_CLK_EN, USB_CTRL);
printk(KERN_INFO "ISP1301 Vendor ID : 0x%04x\n",
i2c_smbus_read_word_data(isp1301_i2c_client, 0x00));
@@ -374,9 +374,13 @@ static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev)
const struct hc_driver *driver = &ohci_nxp_hc_driver;
struct i2c_adapter *i2c_adap;
struct i2c_board_info i2c_info;
+ struct resource *res;
int ret = 0, irq;
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+
dev_dbg(&pdev->dev, "%s: " DRIVER_DESC " (nxp)\n", hcd_name);
if (usb_disabled()) {
dev_err(&pdev->dev, "USB is disabled\n");
@@ -384,16 +388,8 @@ static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev)
goto out;
}
- if (pdev->num_resources != 2
- || pdev->resource[0].flags != IORESOURCE_MEM
- || pdev->resource[1].flags != IORESOURCE_IRQ) {
- dev_err(&pdev->dev, "Invalid resource configuration\\nn");
- ret = -ENODEV;
- goto out;
- }
-
/* Enable AHB slave USB clock, needed for further USB clock control */
- __raw_writel(USB_SLAVE_HCLK_EN | (1 << 19), USB_CTRL);
+ __raw_writel(USB_SLAVE_HCLK_EN | PAD_CONTROL_LAST_DRIVEN, USB_CTRL);
ret = i2c_add_driver(&isp1301_driver);
if (ret < 0) {
@@ -401,6 +397,11 @@ static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev)
goto out;
}
i2c_adap = i2c_get_adapter(2);
+ if (!i2c_adap) {
+ dev_err(&pdev->dev, "failed on i2c_get_adapter");
+ goto out_i2c_driver;
+ }
+
memset(&i2c_info, 0, sizeof(struct i2c_board_info));
strlcpy(i2c_info.type, "isp1301_nxp", I2C_NAME_SIZE);
isp1301_i2c_client = i2c_new_probed_device(i2c_adap, &i2c_info,
@@ -442,7 +443,7 @@ static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev)
while ((__raw_readl(USB_OTG_CLK_STAT) & USB_CLOCK_MASK) !=
USB_CLOCK_MASK) ;
- hcd = usb_create_hcd (driver, &pdev->dev, dev_name(&pdev->dev));
+ hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev));
if (!hcd) {
dev_err(&pdev->dev, "Failed to allocate HC buffer\n");
ret = -ENOMEM;
@@ -452,14 +453,21 @@ static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev)
/* Set all USB bits in the Start Enable register */
nxp_set_usb_bits();
- hcd->rsrc_start = pdev->resource[0].start;
- hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;
- if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
- dev_dbg(&pdev->dev, "request_mem_region failed\n");
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "Failed to get MEM resource\n");
+ ret = -ENOMEM;
+ goto out4;
+ }
+
+ hcd->regs = devm_request_and_ioremap(&pdev->dev, res);
+ if (!hcd->regs) {
+ dev_err(&pdev->dev, "Failed to devm_request_and_ioremap\n");
ret = -ENOMEM;
goto out4;
}
- hcd->regs = (void __iomem *)pdev->resource[0].start;
+ hcd->rsrc_start = res->start;
+ hcd->rsrc_len = resource_size(res);
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
--
1.7.9
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v8 2/5] ohci-nxp: Device tree support
2012-04-29 14:47 [PATCH v8 0/5] USB: LPC32xx device tree related OHCI and UDC patch series Roland Stigge
2012-04-29 14:47 ` [PATCH v8 1/5] ohci-nxp: Driver cleanup Roland Stigge
@ 2012-04-29 14:47 ` Roland Stigge
2012-04-29 14:47 ` [PATCH v8 3/5] USB: Add driver for NXP ISP1301 USB transceiver Roland Stigge
` (3 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Roland Stigge @ 2012-04-29 14:47 UTC (permalink / raw)
To: gregkh, linux-usb, linux-kernel, kevin.wells, srinivas.bakki,
stern, linux-arm-kernel, arnd, grant.likely, rob.herring,
devicetree-discuss
Cc: Roland Stigge
This patch adds device tree support to ohci-nxp.c
Signed-off-by: Roland Stigge <stigge@antcom.de>
---
Documentation/devicetree/bindings/usb/ohci-nxp.txt | 16 ++++++++++++++++
drivers/usb/host/ohci-nxp.c | 10 ++++++++++
2 files changed, 26 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/usb/ohci-nxp.txt
diff --git a/Documentation/devicetree/bindings/usb/ohci-nxp.txt b/Documentation/devicetree/bindings/usb/ohci-nxp.txt
new file mode 100644
index 0000000..b5c3631
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/ohci-nxp.txt
@@ -0,0 +1,16 @@
+* OHCI controller, NXP ohci-nxp variant
+
+Required properties:
+- compatible: must be "nxp,ohci-nxp"
+- reg: physical base address of the controller and length of memory mapped
+ region.
+- interrupts: The OHCI interrupt
+
+Example (LPC32xx):
+
+ ohci@31020000 {
+ compatible = "nxp,ohci-nxp";
+ reg = <0x31020000 0x300>;
+ interrupt-parent = <&mic>;
+ interrupts = <0x3b 0>;
+ };
diff --git a/drivers/usb/host/ohci-nxp.c b/drivers/usb/host/ohci-nxp.c
index 63261f7..bf542e7 100644
--- a/drivers/usb/host/ohci-nxp.c
+++ b/drivers/usb/host/ohci-nxp.c
@@ -22,6 +22,7 @@
#include <linux/clk.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
+#include <linux/of.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@@ -525,10 +526,19 @@ static int usb_hcd_nxp_remove(struct platform_device *pdev)
/* work with hotplug and coldplug */
MODULE_ALIAS("platform:usb-ohci");
+#ifdef CONFIG_OF
+static const struct of_device_id usb_hcd_nxp_match[] = {
+ { .compatible = "nxp,ohci-nxp" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, usb_hcd_nxp_match);
+#endif
+
static struct platform_driver usb_hcd_nxp_driver = {
.driver = {
.name = "usb-ohci",
.owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(usb_hcd_nxp_match),
},
.probe = usb_hcd_nxp_probe,
.remove = usb_hcd_nxp_remove,
--
1.7.9
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v8 3/5] USB: Add driver for NXP ISP1301 USB transceiver
2012-04-29 14:47 [PATCH v8 0/5] USB: LPC32xx device tree related OHCI and UDC patch series Roland Stigge
2012-04-29 14:47 ` [PATCH v8 1/5] ohci-nxp: Driver cleanup Roland Stigge
2012-04-29 14:47 ` [PATCH v8 2/5] ohci-nxp: Device tree support Roland Stigge
@ 2012-04-29 14:47 ` Roland Stigge
2012-04-29 14:47 ` [PATCH v8 4/5] USB: gadget driver for LPC32xx Roland Stigge
` (2 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Roland Stigge @ 2012-04-29 14:47 UTC (permalink / raw)
To: gregkh, linux-usb, linux-kernel, kevin.wells, srinivas.bakki,
stern, linux-arm-kernel, arnd, grant.likely, rob.herring,
devicetree-discuss
Cc: Roland Stigge
This new driver registers the NXP ISP1301 chip via the I2C subsystem. The chip
is the USB transceiver shared by ohci-nxp, lpc32xx_udc (gadget) and
isp1301_omap.
ISP1301 is a very low-level driver that primarily separates out the I2C client
registration of the ISP1301 chip (including instantiation via DT), used by
other drivers, and declares the chip's registers. It's only a helper driver for
some OHCI and USB device drivers. The driver can be considered as a register
set extension of ohci-nxp, lpc32xx-udc and isp1301_omap, which in turn know
best what to do with the low level functionality (individual ISP1301 registers
and timing, see the different initialization strategies in those drivers).
Those drivers previously internally duplicated ISP1301 register definitions
which is solved by this new isp1301 driver. The ISP1301 registers exposed via
isp1301.h can be accessed by other drivers using it with standard i2c_smbus_*()
accesses.
Following patches let the respective USB host and gadget drivers use this
driver, instead of duplicating ISP1301 handling.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
Documentation/devicetree/bindings/usb/isp1301.txt | 25 +++++++
drivers/usb/Kconfig | 2 +
drivers/usb/Makefile | 1 +
drivers/usb/phy/Kconfig | 17 +++++
drivers/usb/phy/Makefile | 7 ++
drivers/usb/phy/isp1301.c | 77 ++++++++++++++++++++
include/linux/usb/isp1301.h | 80 +++++++++++++++++++++
7 files changed, 209 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/usb/isp1301.txt
create mode 100644 drivers/usb/phy/Kconfig
create mode 100644 drivers/usb/phy/Makefile
create mode 100644 drivers/usb/phy/isp1301.c
create mode 100644 include/linux/usb/isp1301.h
diff --git a/Documentation/devicetree/bindings/usb/isp1301.txt b/Documentation/devicetree/bindings/usb/isp1301.txt
new file mode 100644
index 0000000..5405d99
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/isp1301.txt
@@ -0,0 +1,25 @@
+* NXP ISP1301 USB transceiver
+
+Required properties:
+- compatible: must be "nxp,isp1301"
+- reg: I2C address of the ISP1301 device
+
+Optional properties of devices using ISP1301:
+- transceiver: phandle of isp1301 - this helps the ISP1301 driver to find the
+ ISP1301 instance associated with the respective USB driver
+
+Example:
+
+ isp1301: usb-transceiver@2c {
+ compatible = "nxp,isp1301";
+ reg = <0x2c>;
+ };
+
+ usbd@31020000 {
+ compatible = "nxp,lpc3220-udc";
+ reg = <0x31020000 0x300>;
+ interrupt-parent = <&mic>;
+ interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>;
+ transceiver = <&isp1301>;
+ status = "okay";
+ };
diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index 76316a3..4473ae5 100644
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -177,6 +177,8 @@ source "drivers/usb/serial/Kconfig"
source "drivers/usb/misc/Kconfig"
+source "drivers/usb/phy/Kconfig"
+
source "drivers/usb/atm/Kconfig"
source "drivers/usb/gadget/Kconfig"
diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
index 53a7bc0..77c835a 100644
--- a/drivers/usb/Makefile
+++ b/drivers/usb/Makefile
@@ -46,6 +46,7 @@ obj-$(CONFIG_USB_MICROTEK) += image/
obj-$(CONFIG_USB_SERIAL) += serial/
obj-$(CONFIG_USB) += misc/
+obj-$(CONFIG_USB) += phy/
obj-$(CONFIG_EARLY_PRINTK_DBGP) += early/
obj-$(CONFIG_USB_ATM) += atm/
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
new file mode 100644
index 0000000..3cfabcb
--- /dev/null
+++ b/drivers/usb/phy/Kconfig
@@ -0,0 +1,17 @@
+#
+# Physical Layer USB driver configuration
+#
+comment "USB Physical Layer drivers"
+ depends on USB
+
+config USB_ISP1301
+ tristate "NXP ISP1301 USB transceiver support"
+ depends on USB
+ depends on I2C
+ help
+ Say Y here to add support for the NXP ISP1301 USB transceiver driver.
+ This chip is typically used as USB transceiver for USB host, gadget
+ and OTG drivers (to be selected separately).
+
+ To compile this driver as a module, choose M here: the
+ module will be called isp1301.
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
new file mode 100644
index 0000000..eca095b
--- /dev/null
+++ b/drivers/usb/phy/Makefile
@@ -0,0 +1,7 @@
+#
+# Makefile for physical layer USB drivers
+#
+
+ccflags-$(CONFIG_USB_DEBUG) := -DDEBUG
+
+obj-$(CONFIG_USB_ISP1301) += isp1301.o
diff --git a/drivers/usb/phy/isp1301.c b/drivers/usb/phy/isp1301.c
new file mode 100644
index 0000000..b19f493
--- /dev/null
+++ b/drivers/usb/phy/isp1301.c
@@ -0,0 +1,77 @@
+/*
+ * NXP ISP1301 USB transceiver driver
+ *
+ * Copyright (C) 2012 Roland Stigge
+ *
+ * Author: Roland Stigge <stigge@antcom.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/i2c.h>
+
+#define DRV_NAME "isp1301"
+
+#define ISP1301_I2C_ADDR 0x2C
+
+static const unsigned short normal_i2c[] = {
+ ISP1301_I2C_ADDR, ISP1301_I2C_ADDR + 1, I2C_CLIENT_END
+};
+
+static const struct i2c_device_id isp1301_id[] = {
+ { "isp1301", 0 },
+ { }
+};
+
+static struct i2c_client *isp1301_i2c_client;
+
+static int isp1301_probe(struct i2c_client *client,
+ const struct i2c_device_id *i2c_id)
+{
+ isp1301_i2c_client = client;
+ return 0;
+}
+
+static int isp1301_remove(struct i2c_client *client)
+{
+ return 0;
+}
+
+static struct i2c_driver isp1301_driver = {
+ .driver = {
+ .name = DRV_NAME,
+ },
+ .probe = isp1301_probe,
+ .remove = isp1301_remove,
+ .id_table = isp1301_id,
+};
+
+module_i2c_driver(isp1301_driver);
+
+static int match(struct device *dev, void *data)
+{
+ struct device_node *node = (struct device_node *)data;
+ return (dev->of_node == node) &&
+ (dev->driver == &isp1301_driver.driver);
+}
+
+struct i2c_client *isp1301_get_client(struct device_node *node)
+{
+ if (node) { /* reference of ISP1301 I2C node via DT */
+ struct device *dev = bus_find_device(&i2c_bus_type, NULL,
+ node, match);
+ if (!dev)
+ return NULL;
+ return to_i2c_client(dev);
+ } else { /* non-DT: only one ISP1301 chip supported */
+ return isp1301_i2c_client;
+ }
+}
+EXPORT_SYMBOL_GPL(isp1301_get_client);
+
+MODULE_AUTHOR("Roland Stigge <stigge@antcom.de>");
+MODULE_DESCRIPTION("NXP ISP1301 USB transceiver driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/usb/isp1301.h b/include/linux/usb/isp1301.h
new file mode 100644
index 0000000..d3a851c
--- /dev/null
+++ b/include/linux/usb/isp1301.h
@@ -0,0 +1,80 @@
+/*
+ * NXP ISP1301 USB transceiver driver
+ *
+ * Copyright (C) 2012 Roland Stigge <stigge@antcom.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __LINUX_USB_ISP1301_H
+#define __LINUX_USB_ISP1301_H
+
+#include <linux/of.h>
+
+/* I2C Register definitions: */
+
+#define ISP1301_I2C_MODE_CONTROL_1 0x04 /* u8 read, set, +1 clear */
+
+#define MC1_SPEED_REG (1 << 0)
+#define MC1_SUSPEND_REG (1 << 1)
+#define MC1_DAT_SE0 (1 << 2)
+#define MC1_TRANSPARENT (1 << 3)
+#define MC1_BDIS_ACON_EN (1 << 4)
+#define MC1_OE_INT_EN (1 << 5)
+#define MC1_UART_EN (1 << 6)
+#define MC1_MASK 0x7f
+
+#define ISP1301_I2C_MODE_CONTROL_2 0x12 /* u8 read, set, +1 clear */
+
+#define MC2_GLOBAL_PWR_DN (1 << 0)
+#define MC2_SPD_SUSP_CTRL (1 << 1)
+#define MC2_BI_DI (1 << 2)
+#define MC2_TRANSP_BDIR0 (1 << 3)
+#define MC2_TRANSP_BDIR1 (1 << 4)
+#define MC2_AUDIO_EN (1 << 5)
+#define MC2_PSW_EN (1 << 6)
+#define MC2_EN2V7 (1 << 7)
+
+#define ISP1301_I2C_OTG_CONTROL_1 0x06 /* u8 read, set, +1 clear */
+
+#define OTG1_DP_PULLUP (1 << 0)
+#define OTG1_DM_PULLUP (1 << 1)
+#define OTG1_DP_PULLDOWN (1 << 2)
+#define OTG1_DM_PULLDOWN (1 << 3)
+#define OTG1_ID_PULLDOWN (1 << 4)
+#define OTG1_VBUS_DRV (1 << 5)
+#define OTG1_VBUS_DISCHRG (1 << 6)
+#define OTG1_VBUS_CHRG (1 << 7)
+
+#define ISP1301_I2C_OTG_CONTROL_2 0x10 /* u8 readonly */
+
+#define OTG_B_SESS_END (1 << 6)
+#define OTG_B_SESS_VLD (1 << 7)
+
+#define ISP1301_I2C_INTERRUPT_SOURCE 0x8
+#define ISP1301_I2C_INTERRUPT_LATCH 0xA
+#define ISP1301_I2C_INTERRUPT_FALLING 0xC
+#define ISP1301_I2C_INTERRUPT_RISING 0xE
+
+#define INT_VBUS_VLD (1 << 0)
+#define INT_SESS_VLD (1 << 1)
+#define INT_DP_HI (1 << 2)
+#define INT_ID_GND (1 << 3)
+#define INT_DM_HI (1 << 4)
+#define INT_ID_FLOAT (1 << 5)
+#define INT_BDIS_ACON (1 << 6)
+#define INT_CR_INT (1 << 7)
+
+#define ISP1301_I2C_REG_CLEAR_ADDR 1 /* Register Address Modifier */
+
+struct i2c_client *isp1301_get_client(struct device_node *node);
+
+#endif /* __LINUX_USB_ISP1301_H */
--
1.7.9
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v8 4/5] USB: gadget driver for LPC32xx
2012-04-29 14:47 [PATCH v8 0/5] USB: LPC32xx device tree related OHCI and UDC patch series Roland Stigge
` (2 preceding siblings ...)
2012-04-29 14:47 ` [PATCH v8 3/5] USB: Add driver for NXP ISP1301 USB transceiver Roland Stigge
@ 2012-04-29 14:47 ` Roland Stigge
2012-04-29 14:47 ` [PATCH v8 5/5] USB: ohci-nxp: Use isp1301 driver Roland Stigge
2012-05-01 17:37 ` [PATCH v8 0/5] USB: LPC32xx device tree related OHCI and UDC patch series Greg KH
5 siblings, 0 replies; 7+ messages in thread
From: Roland Stigge @ 2012-04-29 14:47 UTC (permalink / raw)
To: gregkh, linux-usb, linux-kernel, kevin.wells, srinivas.bakki,
stern, linux-arm-kernel, arnd, grant.likely, rob.herring,
devicetree-discuss
Cc: Roland Stigge
This patch adds a USB gadget driver for the LPC32xx ARM SoC.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
.../devicetree/bindings/usb/lpc32xx-udc.txt | 28 +
drivers/usb/gadget/Kconfig | 11 +
drivers/usb/gadget/Makefile | 1 +
drivers/usb/gadget/gadget_chips.h | 3 +
drivers/usb/gadget/lpc32xx_udc.c | 3538 ++++++++++++++++++++
5 files changed, 3581 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/usb/lpc32xx-udc.txt
create mode 100644 drivers/usb/gadget/lpc32xx_udc.c
diff --git a/Documentation/devicetree/bindings/usb/lpc32xx-udc.txt b/Documentation/devicetree/bindings/usb/lpc32xx-udc.txt
new file mode 100644
index 0000000..29f12a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/lpc32xx-udc.txt
@@ -0,0 +1,28 @@
+* NXP LPC32xx SoC USB Device Controller (UDC)
+
+Required properties:
+- compatible: Must be "nxp,lpc3220-udc"
+- reg: Physical base address of the controller and length of memory mapped
+ region.
+- interrupts: The USB interrupts:
+ * USB Device Low Priority Interrupt
+ * USB Device High Priority Interrupt
+ * USB Device DMA Interrupt
+ * External USB Transceiver Interrupt (OTG ATX)
+- transceiver: phandle of the associated ISP1301 device - this is necessary for
+ the UDC controller for connecting to the USB physical layer
+
+Example:
+
+ isp1301: usb-transceiver@2c {
+ compatible = "nxp,isp1301";
+ reg = <0x2c>;
+ };
+
+ usbd@31020000 {
+ compatible = "nxp,lpc3220-udc";
+ reg = <0x31020000 0x300>;
+ interrupt-parent = <&mic>;
+ interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>;
+ transceiver = <&isp1301>;
+ };
diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
index 2633f75..8276972 100644
--- a/drivers/usb/gadget/Kconfig
+++ b/drivers/usb/gadget/Kconfig
@@ -147,6 +147,17 @@ config USB_AT91
dynamically linked module called "at91_udc" and force all
gadget drivers to also be dynamically linked.
+config USB_LPC32XX
+ tristate "LPC32XX USB Peripheral Controller"
+ depends on ARCH_LPC32XX
+ select USB_ISP1301
+ help
+ This option selects the USB device controller in the LPC32xx SoC.
+
+ Say "y" to link the driver statically, or "m" to build a
+ dynamically linked module called "lpc32xx_udc" and force all
+ gadget drivers to also be dynamically linked.
+
config USB_ATMEL_USBA
tristate "Atmel USBA"
select USB_GADGET_DUALSPEED
diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile
index b7f6eef..1565253 100644
--- a/drivers/usb/gadget/Makefile
+++ b/drivers/usb/gadget/Makefile
@@ -26,6 +26,7 @@ obj-$(CONFIG_USB_CI13XXX_PCI) += ci13xxx_pci.o
obj-$(CONFIG_USB_S3C_HSOTG) += s3c-hsotg.o
obj-$(CONFIG_USB_S3C_HSUDC) += s3c-hsudc.o
obj-$(CONFIG_USB_LANGWELL) += langwell_udc.o
+obj-$(CONFIG_USB_LPC32XX) += lpc32xx_udc.o
obj-$(CONFIG_USB_EG20T) += pch_udc.o
obj-$(CONFIG_USB_MV_UDC) += mv_udc.o
mv_udc-y := mv_udc_core.o
diff --git a/drivers/usb/gadget/gadget_chips.h b/drivers/usb/gadget/gadget_chips.h
index a8855d0..b8b3a34 100644
--- a/drivers/usb/gadget/gadget_chips.h
+++ b/drivers/usb/gadget/gadget_chips.h
@@ -37,6 +37,7 @@
#define gadget_is_goku(g) (!strcmp("goku_udc", (g)->name))
#define gadget_is_imx(g) (!strcmp("imx_udc", (g)->name))
#define gadget_is_langwell(g) (!strcmp("langwell_udc", (g)->name))
+#define gadget_is_lpc32xx(g) (!strcmp("lpc32xx_udc", (g)->name))
#define gadget_is_m66592(g) (!strcmp("m66592_udc", (g)->name))
#define gadget_is_musbhdrc(g) (!strcmp("musb-hdrc", (g)->name))
#define gadget_is_net2272(g) (!strcmp("net2272", (g)->name))
@@ -118,6 +119,8 @@ static inline int usb_gadget_controller_number(struct usb_gadget *gadget)
return 0x31;
else if (gadget_is_dwc3(gadget))
return 0x32;
+ else if (gadget_is_lpc32xx(gadget))
+ return 0x33;
return -ENOENT;
}
diff --git a/drivers/usb/gadget/lpc32xx_udc.c b/drivers/usb/gadget/lpc32xx_udc.c
new file mode 100644
index 0000000..262acfd
--- /dev/null
+++ b/drivers/usb/gadget/lpc32xx_udc.c
@@ -0,0 +1,3538 @@
+/*
+ * USB Gadget driver for LPC32xx
+ *
+ * Authors:
+ * Kevin Wells <kevin.wells@nxp.com>
+ * Mike James
+ * Roland Stigge <stigge@antcom.de>
+ *
+ * Copyright (C) 2006 Philips Semiconductors
+ * Copyright (C) 2009 NXP Semiconductors
+ * Copyright (C) 2012 Roland Stigge
+ *
+ * Note: This driver is based on original work done by Mike James for
+ * the LPC3180.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/ioport.h>
+#include <linux/slab.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/list.h>
+#include <linux/interrupt.h>
+#include <linux/proc_fs.h>
+#include <linux/clk.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+#include <linux/i2c.h>
+#include <linux/kthread.h>
+#include <linux/freezer.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmapool.h>
+#include <linux/workqueue.h>
+#include <linux/of.h>
+#include <linux/usb/isp1301.h>
+
+#include <asm/byteorder.h>
+#include <mach/hardware.h>
+#include <linux/io.h>
+#include <asm/irq.h>
+#include <asm/system.h>
+
+#include <mach/platform.h>
+#include <mach/irqs.h>
+#include <mach/board.h>
+#ifdef CONFIG_USB_GADGET_DEBUG_FILES
+#include <linux/seq_file.h>
+#endif
+
+/*
+ * USB device configuration structure
+ */
+typedef void (*usc_chg_event)(int);
+struct lpc32xx_usbd_cfg {
+ int vbus_drv_pol; /* 0=active low drive for VBUS via ISP1301 */
+ usc_chg_event conn_chgb; /* Connection change event (optional) */
+ usc_chg_event susp_chgb; /* Suspend/resume event (optional) */
+ usc_chg_event rmwk_chgb; /* Enable/disable remote wakeup */
+};
+
+/*
+ * controller driver data structures
+ */
+
+/* 16 endpoints (not to be confused with 32 hardware endpoints) */
+#define NUM_ENDPOINTS 16
+
+/*
+ * IRQ indices make reading the code a little easier
+ */
+#define IRQ_USB_LP 0
+#define IRQ_USB_HP 1
+#define IRQ_USB_DEVDMA 2
+#define IRQ_USB_ATX 3
+
+#define EP_OUT 0 /* RX (from host) */
+#define EP_IN 1 /* TX (to host) */
+
+/* Returns the interrupt mask for the selected hardware endpoint */
+#define EP_MASK_SEL(ep, dir) (1 << (((ep) * 2) + dir))
+
+#define EP_INT_TYPE 0
+#define EP_ISO_TYPE 1
+#define EP_BLK_TYPE 2
+#define EP_CTL_TYPE 3
+
+/* EP0 states */
+#define WAIT_FOR_SETUP 0 /* Wait for setup packet */
+#define DATA_IN 1 /* Expect dev->host transfer */
+#define DATA_OUT 2 /* Expect host->dev transfer */
+
+/* DD (DMA Descriptor) structure, requires word alignment, this is already
+ * defined in the LPC32XX USB device header file, but this version is slightly
+ * modified to tag some work data with each DMA descriptor. */
+struct lpc32xx_usbd_dd_gad {
+ u32 dd_next_phy;
+ u32 dd_setup;
+ u32 dd_buffer_addr;
+ u32 dd_status;
+ u32 dd_iso_ps_mem_addr;
+ u32 this_dma;
+ u32 iso_status[6]; /* 5 spare */
+ u32 dd_next_v;
+};
+
+/*
+ * Logical endpoint structure
+ */
+struct lpc32xx_ep {
+ struct usb_ep ep;
+ struct list_head queue;
+ struct lpc32xx_udc *udc;
+
+ u32 hwep_num_base; /* Physical hardware EP */
+ u32 hwep_num; /* Maps to hardware endpoint */
+ u32 maxpacket;
+ u32 lep;
+
+ bool is_in;
+ bool req_pending;
+ u32 eptype;
+
+ u32 totalints;
+
+ bool wedge;
+
+ const struct usb_endpoint_descriptor *desc;
+};
+
+/*
+ * Common UDC structure
+ */
+struct lpc32xx_udc {
+ struct usb_gadget gadget;
+ struct usb_gadget_driver *driver;
+ struct platform_device *pdev;
+ struct device *dev;
+ struct dentry *pde;
+ spinlock_t lock;
+ struct i2c_client *isp1301_i2c_client;
+
+ /* Board and device specific */
+ struct lpc32xx_usbd_cfg *board;
+ u32 io_p_start;
+ u32 io_p_size;
+ void __iomem *udp_baseaddr;
+ int udp_irq[4];
+ struct clk *usb_pll_clk;
+ struct clk *usb_slv_clk;
+
+ /* DMA support */
+ u32 *udca_v_base;
+ u32 udca_p_base;
+ struct dma_pool *dd_cache;
+
+ /* Common EP and control data */
+ u32 enabled_devints;
+ u32 enabled_hwepints;
+ u32 dev_status;
+ u32 realized_eps;
+
+ /* VBUS detection, pullup, and power flags */
+ u8 vbus;
+ u8 last_vbus;
+ int pullup;
+ int poweron;
+
+ /* Work queues related to I2C support */
+ struct work_struct pullup_job;
+ struct work_struct vbus_job;
+ struct work_struct power_job;
+
+ /* USB device peripheral - various */
+ struct lpc32xx_ep ep[NUM_ENDPOINTS];
+ bool enabled;
+ bool clocked;
+ bool suspended;
+ bool selfpowered;
+ int ep0state;
+ atomic_t enabled_ep_cnt;
+ wait_queue_head_t ep_disable_wait_queue;
+};
+
+/*
+ * Endpoint request
+ */
+struct lpc32xx_request {
+ struct usb_request req;
+ struct list_head queue;
+ struct lpc32xx_usbd_dd_gad *dd_desc_ptr;
+ bool mapped;
+ bool send_zlp;
+};
+
+static inline struct lpc32xx_udc *to_udc(struct usb_gadget *g)
+{
+ return container_of(g, struct lpc32xx_udc, gadget);
+}
+
+#define ep_dbg(epp, fmt, arg...) \
+ dev_dbg(epp->udc->dev, "%s: " fmt, __func__, ## arg)
+#define ep_err(epp, fmt, arg...) \
+ dev_err(epp->udc->dev, "%s: " fmt, __func__, ## arg)
+#define ep_info(epp, fmt, arg...) \
+ dev_info(epp->udc->dev, "%s: " fmt, __func__, ## arg)
+#define ep_warn(epp, fmt, arg...) \
+ dev_warn(epp->udc->dev, "%s:" fmt, __func__, ## arg)
+
+#define UDCA_BUFF_SIZE (128)
+
+/* TODO: When the clock framework is introduced in LPC32xx, IO_ADDRESS will
+ * be replaced with an inremap()ed pointer, see USB_OTG_CLK_CTRL()
+ * */
+#define USB_CTRL IO_ADDRESS(LPC32XX_CLK_PM_BASE + 0x64)
+#define USB_CLOCK_MASK (AHB_M_CLOCK_ON | OTG_CLOCK_ON | \
+ DEV_CLOCK_ON | I2C_CLOCK_ON)
+
+/* USB_CTRL bit defines */
+#define USB_SLAVE_HCLK_EN (1 << 24)
+#define USB_HOST_NEED_CLK_EN (1 << 21)
+#define USB_DEV_NEED_CLK_EN (1 << 22)
+
+#define USB_OTG_CLK_CTRL(udc) ((udc)->udp_baseaddr + 0xFF4)
+#define USB_OTG_CLK_STAT(udc) ((udc)->udp_baseaddr + 0xFF8)
+
+/* USB_OTG_CLK_CTRL bit defines */
+#define AHB_M_CLOCK_ON (1 << 4)
+#define OTG_CLOCK_ON (1 << 3)
+#define I2C_CLOCK_ON (1 << 2)
+#define DEV_CLOCK_ON (1 << 1)
+#define HOST_CLOCK_ON (1 << 0)
+
+#define USB_OTG_STAT_CONTROL(udc) (udc->udp_baseaddr + 0x110)
+
+/* USB_OTG_STAT_CONTROL bit defines */
+#define TRANSPARENT_I2C_EN (1 << 7)
+#define HOST_EN (1 << 0)
+
+/**********************************************************************
+ * USB device controller register offsets
+ **********************************************************************/
+
+#define USBD_DEVINTST(x) ((x) + 0x200)
+#define USBD_DEVINTEN(x) ((x) + 0x204)
+#define USBD_DEVINTCLR(x) ((x) + 0x208)
+#define USBD_DEVINTSET(x) ((x) + 0x20C)
+#define USBD_CMDCODE(x) ((x) + 0x210)
+#define USBD_CMDDATA(x) ((x) + 0x214)
+#define USBD_RXDATA(x) ((x) + 0x218)
+#define USBD_TXDATA(x) ((x) + 0x21C)
+#define USBD_RXPLEN(x) ((x) + 0x220)
+#define USBD_TXPLEN(x) ((x) + 0x224)
+#define USBD_CTRL(x) ((x) + 0x228)
+#define USBD_DEVINTPRI(x) ((x) + 0x22C)
+#define USBD_EPINTST(x) ((x) + 0x230)
+#define USBD_EPINTEN(x) ((x) + 0x234)
+#define USBD_EPINTCLR(x) ((x) + 0x238)
+#define USBD_EPINTSET(x) ((x) + 0x23C)
+#define USBD_EPINTPRI(x) ((x) + 0x240)
+#define USBD_REEP(x) ((x) + 0x244)
+#define USBD_EPIND(x) ((x) + 0x248)
+#define USBD_EPMAXPSIZE(x) ((x) + 0x24C)
+/* DMA support registers only below */
+/* Set, clear, or get enabled state of the DMA request status. If
+ * enabled, an IN or OUT token will start a DMA transfer for the EP */
+#define USBD_DMARST(x) ((x) + 0x250)
+#define USBD_DMARCLR(x) ((x) + 0x254)
+#define USBD_DMARSET(x) ((x) + 0x258)
+/* DMA UDCA head pointer */
+#define USBD_UDCAH(x) ((x) + 0x280)
+/* EP DMA status, enable, and disable. This is used to specifically
+ * enabled or disable DMA for a specific EP */
+#define USBD_EPDMAST(x) ((x) + 0x284)
+#define USBD_EPDMAEN(x) ((x) + 0x288)
+#define USBD_EPDMADIS(x) ((x) + 0x28C)
+/* DMA master interrupts enable and pending interrupts */
+#define USBD_DMAINTST(x) ((x) + 0x290)
+#define USBD_DMAINTEN(x) ((x) + 0x294)
+/* DMA end of transfer interrupt enable, disable, status */
+#define USBD_EOTINTST(x) ((x) + 0x2A0)
+#define USBD_EOTINTCLR(x) ((x) + 0x2A4)
+#define USBD_EOTINTSET(x) ((x) + 0x2A8)
+/* New DD request interrupt enable, disable, status */
+#define USBD_NDDRTINTST(x) ((x) + 0x2AC)
+#define USBD_NDDRTINTCLR(x) ((x) + 0x2B0)
+#define USBD_NDDRTINTSET(x) ((x) + 0x2B4)
+/* DMA error interrupt enable, disable, status */
+#define USBD_SYSERRTINTST(x) ((x) + 0x2B8)
+#define USBD_SYSERRTINTCLR(x) ((x) + 0x2BC)
+#define USBD_SYSERRTINTSET(x) ((x) + 0x2C0)
+
+/**********************************************************************
+ * USBD_DEVINTST/USBD_DEVINTEN/USBD_DEVINTCLR/USBD_DEVINTSET/
+ * USBD_DEVINTPRI register definitions
+ **********************************************************************/
+#define USBD_ERR_INT (1 << 9)
+#define USBD_EP_RLZED (1 << 8)
+#define USBD_TXENDPKT (1 << 7)
+#define USBD_RXENDPKT (1 << 6)
+#define USBD_CDFULL (1 << 5)
+#define USBD_CCEMPTY (1 << 4)
+#define USBD_DEV_STAT (1 << 3)
+#define USBD_EP_SLOW (1 << 2)
+#define USBD_EP_FAST (1 << 1)
+#define USBD_FRAME (1 << 0)
+
+/**********************************************************************
+ * USBD_EPINTST/USBD_EPINTEN/USBD_EPINTCLR/USBD_EPINTSET/
+ * USBD_EPINTPRI register definitions
+ **********************************************************************/
+/* End point selection macro (RX) */
+#define USBD_RX_EP_SEL(e) (1 << ((e) << 1))
+
+/* End point selection macro (TX) */
+#define USBD_TX_EP_SEL(e) (1 << (((e) << 1) + 1))
+
+/**********************************************************************
+ * USBD_REEP/USBD_DMARST/USBD_DMARCLR/USBD_DMARSET/USBD_EPDMAST/
+ * USBD_EPDMAEN/USBD_EPDMADIS/
+ * USBD_NDDRTINTST/USBD_NDDRTINTCLR/USBD_NDDRTINTSET/
+ * USBD_EOTINTST/USBD_EOTINTCLR/USBD_EOTINTSET/
+ * USBD_SYSERRTINTST/USBD_SYSERRTINTCLR/USBD_SYSERRTINTSET
+ * register definitions
+ **********************************************************************/
+/* Endpoint selection macro */
+#define USBD_EP_SEL(e) (1 << (e))
+
+/**********************************************************************
+ * SBD_DMAINTST/USBD_DMAINTEN
+ **********************************************************************/
+#define USBD_SYS_ERR_INT (1 << 2)
+#define USBD_NEW_DD_INT (1 << 1)
+#define USBD_EOT_INT (1 << 0)
+
+/**********************************************************************
+ * USBD_RXPLEN register definitions
+ **********************************************************************/
+#define USBD_PKT_RDY (1 << 11)
+#define USBD_DV (1 << 10)
+#define USBD_PK_LEN_MASK 0x3FF
+
+/**********************************************************************
+ * USBD_CTRL register definitions
+ **********************************************************************/
+#define USBD_LOG_ENDPOINT(e) ((e) << 2)
+#define USBD_WR_EN (1 << 1)
+#define USBD_RD_EN (1 << 0)
+
+/**********************************************************************
+ * USBD_CMDCODE register definitions
+ **********************************************************************/
+#define USBD_CMD_CODE(c) ((c) << 16)
+#define USBD_CMD_PHASE(p) ((p) << 8)
+
+/**********************************************************************
+ * USBD_DMARST/USBD_DMARCLR/USBD_DMARSET register definitions
+ **********************************************************************/
+#define USBD_DMAEP(e) (1 << (e))
+
+/* DD (DMA Descriptor) structure, requires word alignment */
+struct lpc32xx_usbd_dd {
+ u32 *dd_next;
+ u32 dd_setup;
+ u32 dd_buffer_addr;
+ u32 dd_status;
+ u32 dd_iso_ps_mem_addr;
+};
+
+/* dd_setup bit defines */
+#define DD_SETUP_ATLE_DMA_MODE 0x01
+#define DD_SETUP_NEXT_DD_VALID 0x04
+#define DD_SETUP_ISO_EP 0x10
+#define DD_SETUP_PACKETLEN(n) (((n) & 0x7FF) << 5)
+#define DD_SETUP_DMALENBYTES(n) (((n) & 0xFFFF) << 16)
+
+/* dd_status bit defines */
+#define DD_STATUS_DD_RETIRED 0x01
+#define DD_STATUS_STS_MASK 0x1E
+#define DD_STATUS_STS_NS 0x00 /* Not serviced */
+#define DD_STATUS_STS_BS 0x02 /* Being serviced */
+#define DD_STATUS_STS_NC 0x04 /* Normal completion */
+#define DD_STATUS_STS_DUR 0x06 /* Data underrun (short packet) */
+#define DD_STATUS_STS_DOR 0x08 /* Data overrun */
+#define DD_STATUS_STS_SE 0x12 /* System error */
+#define DD_STATUS_PKT_VAL 0x20 /* Packet valid */
+#define DD_STATUS_LSB_EX 0x40 /* LS byte extracted (ATLE) */
+#define DD_STATUS_MSB_EX 0x80 /* MS byte extracted (ATLE) */
+#define DD_STATUS_MLEN(n) (((n) >> 8) & 0x3F)
+#define DD_STATUS_CURDMACNT(n) (((n) >> 16) & 0xFFFF)
+
+/*
+ *
+ * Protocol engine bits below
+ *
+ */
+/* Device Interrupt Bit Definitions */
+#define FRAME_INT 0x00000001
+#define EP_FAST_INT 0x00000002
+#define EP_SLOW_INT 0x00000004
+#define DEV_STAT_INT 0x00000008
+#define CCEMTY_INT 0x00000010
+#define CDFULL_INT 0x00000020
+#define RxENDPKT_INT 0x00000040
+#define TxENDPKT_INT 0x00000080
+#define EP_RLZED_INT 0x00000100
+#define ERR_INT 0x00000200
+
+/* Rx & Tx Packet Length Definitions */
+#define PKT_LNGTH_MASK 0x000003FF
+#define PKT_DV 0x00000400
+#define PKT_RDY 0x00000800
+
+/* USB Control Definitions */
+#define CTRL_RD_EN 0x00000001
+#define CTRL_WR_EN 0x00000002
+
+/* Command Codes */
+#define CMD_SET_ADDR 0x00D00500
+#define CMD_CFG_DEV 0x00D80500
+#define CMD_SET_MODE 0x00F30500
+#define CMD_RD_FRAME 0x00F50500
+#define DAT_RD_FRAME 0x00F50200
+#define CMD_RD_TEST 0x00FD0500
+#define DAT_RD_TEST 0x00FD0200
+#define CMD_SET_DEV_STAT 0x00FE0500
+#define CMD_GET_DEV_STAT 0x00FE0500
+#define DAT_GET_DEV_STAT 0x00FE0200
+#define CMD_GET_ERR_CODE 0x00FF0500
+#define DAT_GET_ERR_CODE 0x00FF0200
+#define CMD_RD_ERR_STAT 0x00FB0500
+#define DAT_RD_ERR_STAT 0x00FB0200
+#define DAT_WR_BYTE(x) (0x00000100 | ((x) << 16))
+#define CMD_SEL_EP(x) (0x00000500 | ((x) << 16))
+#define DAT_SEL_EP(x) (0x00000200 | ((x) << 16))
+#define CMD_SEL_EP_CLRI(x) (0x00400500 | ((x) << 16))
+#define DAT_SEL_EP_CLRI(x) (0x00400200 | ((x) << 16))
+#define CMD_SET_EP_STAT(x) (0x00400500 | ((x) << 16))
+#define CMD_CLR_BUF 0x00F20500
+#define DAT_CLR_BUF 0x00F20200
+#define CMD_VALID_BUF 0x00FA0500
+
+/* Device Address Register Definitions */
+#define DEV_ADDR_MASK 0x7F
+#define DEV_EN 0x80
+
+/* Device Configure Register Definitions */
+#define CONF_DVICE 0x01
+
+/* Device Mode Register Definitions */
+#define AP_CLK 0x01
+#define INAK_CI 0x02
+#define INAK_CO 0x04
+#define INAK_II 0x08
+#define INAK_IO 0x10
+#define INAK_BI 0x20
+#define INAK_BO 0x40
+
+/* Device Status Register Definitions */
+#define DEV_CON 0x01
+#define DEV_CON_CH 0x02
+#define DEV_SUS 0x04
+#define DEV_SUS_CH 0x08
+#define DEV_RST 0x10
+
+/* Error Code Register Definitions */
+#define ERR_EC_MASK 0x0F
+#define ERR_EA 0x10
+
+/* Error Status Register Definitions */
+#define ERR_PID 0x01
+#define ERR_UEPKT 0x02
+#define ERR_DCRC 0x04
+#define ERR_TIMOUT 0x08
+#define ERR_EOP 0x10
+#define ERR_B_OVRN 0x20
+#define ERR_BTSTF 0x40
+#define ERR_TGL 0x80
+
+/* Endpoint Select Register Definitions */
+#define EP_SEL_F 0x01
+#define EP_SEL_ST 0x02
+#define EP_SEL_STP 0x04
+#define EP_SEL_PO 0x08
+#define EP_SEL_EPN 0x10
+#define EP_SEL_B_1_FULL 0x20
+#define EP_SEL_B_2_FULL 0x40
+
+/* Endpoint Status Register Definitions */
+#define EP_STAT_ST 0x01
+#define EP_STAT_DA 0x20
+#define EP_STAT_RF_MO 0x40
+#define EP_STAT_CND_ST 0x80
+
+/* Clear Buffer Register Definitions */
+#define CLR_BUF_PO 0x01
+
+/* DMA Interrupt Bit Definitions */
+#define EOT_INT 0x01
+#define NDD_REQ_INT 0x02
+#define SYS_ERR_INT 0x04
+
+#define DRIVER_VERSION "1.03"
+static const char driver_name[] = "lpc32xx_udc";
+
+/*
+ *
+ * proc interface support
+ *
+ */
+#ifdef CONFIG_USB_GADGET_DEBUG_FILES
+static char *epnames[] = {"INT", "ISO", "BULK", "CTRL"};
+static const char debug_filename[] = "driver/udc";
+
+static void proc_ep_show(struct seq_file *s, struct lpc32xx_ep *ep)
+{
+ struct lpc32xx_request *req;
+
+ seq_printf(s, "\n");
+ seq_printf(s, "%12s, maxpacket %4d %3s",
+ ep->ep.name, ep->ep.maxpacket,
+ ep->is_in ? "in" : "out");
+ seq_printf(s, " type %4s", epnames[ep->eptype]);
+ seq_printf(s, " ints: %12d", ep->totalints);
+
+ if (list_empty(&ep->queue))
+ seq_printf(s, "\t(queue empty)\n");
+ else {
+ list_for_each_entry(req, &ep->queue, queue) {
+ u32 length = req->req.actual;
+
+ seq_printf(s, "\treq %p len %d/%d buf %p\n",
+ &req->req, length,
+ req->req.length, req->req.buf);
+ }
+ }
+}
+
+static int proc_udc_show(struct seq_file *s, void *unused)
+{
+ struct lpc32xx_udc *udc = s->private;
+ struct lpc32xx_ep *ep;
+ unsigned long flags;
+
+ seq_printf(s, "%s: version %s\n", driver_name, DRIVER_VERSION);
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ seq_printf(s, "vbus %s, pullup %s, %s powered%s, gadget %s\n\n",
+ udc->vbus ? "present" : "off",
+ udc->enabled ? (udc->vbus ? "active" : "enabled") :
+ "disabled",
+ udc->selfpowered ? "self" : "VBUS",
+ udc->suspended ? ", suspended" : "",
+ udc->driver ? udc->driver->driver.name : "(none)");
+
+ if (udc->enabled && udc->vbus) {
+ proc_ep_show(s, &udc->ep[0]);
+ list_for_each_entry(ep, &udc->gadget.ep_list, ep.ep_list) {
+ if (ep->desc)
+ proc_ep_show(s, ep);
+ }
+ }
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ return 0;
+}
+
+static int proc_udc_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, proc_udc_show, PDE(inode)->data);
+}
+
+static const struct file_operations proc_ops = {
+ .owner = THIS_MODULE,
+ .open = proc_udc_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static void create_debug_file(struct lpc32xx_udc *udc)
+{
+ udc->pde = debugfs_create_file(debug_filename, 0, NULL, udc, &proc_ops);
+}
+
+static void remove_debug_file(struct lpc32xx_udc *udc)
+{
+ if (udc->pde)
+ debugfs_remove(udc->pde);
+}
+
+#else
+static inline void create_debug_file(struct lpc32xx_udc *udc) {}
+static inline void remove_debug_file(struct lpc32xx_udc *udc) {}
+#endif
+
+/* Primary initialization sequence for the ISP1301 transceiver */
+static void isp1301_udc_configure(struct lpc32xx_udc *udc)
+{
+ /* LPC32XX only supports DAT_SE0 USB mode */
+ /* This sequence is important */
+
+ /* Disable transparent UART mode first */
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ (ISP1301_I2C_MODE_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR),
+ MC1_UART_EN);
+
+ /* Set full speed and SE0 mode */
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ (ISP1301_I2C_MODE_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR), ~0);
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_MODE_CONTROL_1, (MC1_SPEED_REG | MC1_DAT_SE0));
+
+ /*
+ * The PSW_OE enable bit state is reversed in the ISP1301 User's Guide
+ */
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ (ISP1301_I2C_MODE_CONTROL_2 | ISP1301_I2C_REG_CLEAR_ADDR), ~0);
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_MODE_CONTROL_2, (MC2_BI_DI | MC2_SPD_SUSP_CTRL));
+
+ /* Driver VBUS_DRV high or low depending on board setup */
+ if (udc->board->vbus_drv_pol != 0)
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_OTG_CONTROL_1, OTG1_VBUS_DRV);
+ else
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR,
+ OTG1_VBUS_DRV);
+
+ /* Bi-directional mode with suspend control
+ * Enable both pulldowns for now - the pullup will be enable when VBUS
+ * is detected */
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ (ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR), ~0);
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_OTG_CONTROL_1,
+ (0 | OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN));
+
+ /* Discharge VBUS (just in case) */
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_OTG_CONTROL_1, OTG1_VBUS_DISCHRG);
+ msleep(1);
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ (ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR),
+ OTG1_VBUS_DISCHRG);
+
+ /* Clear and enable VBUS high edge interrupt */
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_INTERRUPT_LATCH | ISP1301_I2C_REG_CLEAR_ADDR, ~0);
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_INTERRUPT_FALLING | ISP1301_I2C_REG_CLEAR_ADDR, ~0);
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_INTERRUPT_FALLING, INT_VBUS_VLD);
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_INTERRUPT_RISING | ISP1301_I2C_REG_CLEAR_ADDR, ~0);
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_INTERRUPT_RISING, INT_VBUS_VLD);
+
+ /* Enable usb_need_clk clock after transceiver is initialized */
+ writel((readl(USB_CTRL) | (1 << 22)), USB_CTRL);
+
+ dev_info(udc->dev, "ISP1301 Vendor ID : 0x%04x\n",
+ i2c_smbus_read_word_data(udc->isp1301_i2c_client, 0x00));
+ dev_info(udc->dev, "ISP1301 Product ID : 0x%04x\n",
+ i2c_smbus_read_word_data(udc->isp1301_i2c_client, 0x02));
+ dev_info(udc->dev, "ISP1301 Version ID : 0x%04x\n",
+ i2c_smbus_read_word_data(udc->isp1301_i2c_client, 0x14));
+}
+
+/* Enables or disables the USB device pullup via the ISP1301 transceiver */
+static void isp1301_pullup_set(struct lpc32xx_udc *udc)
+{
+ if (udc->pullup)
+ /* Enable pullup for bus signalling */
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_OTG_CONTROL_1, OTG1_DP_PULLUP);
+ else
+ /* Enable pullup for bus signalling */
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR,
+ OTG1_DP_PULLUP);
+}
+
+static void pullup_work(struct work_struct *work)
+{
+ struct lpc32xx_udc *udc =
+ container_of(work, struct lpc32xx_udc, pullup_job);
+
+ isp1301_pullup_set(udc);
+}
+
+static void isp1301_pullup_enable(struct lpc32xx_udc *udc, int en_pullup,
+ int block)
+{
+ if (en_pullup == udc->pullup)
+ return;
+
+ udc->pullup = en_pullup;
+ if (block)
+ isp1301_pullup_set(udc);
+ else
+ /* defer slow i2c pull up setting */
+ schedule_work(&udc->pullup_job);
+}
+
+#ifdef CONFIG_PM
+/* Powers up or down the ISP1301 transceiver */
+static void isp1301_set_powerstate(struct lpc32xx_udc *udc, int enable)
+{
+ if (enable != 0)
+ /* Power up ISP1301 - this ISP1301 will automatically wakeup
+ when VBUS is detected */
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_MODE_CONTROL_2 | ISP1301_I2C_REG_CLEAR_ADDR,
+ MC2_GLOBAL_PWR_DN);
+ else
+ /* Power down ISP1301 */
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_MODE_CONTROL_2, MC2_GLOBAL_PWR_DN);
+}
+
+static void power_work(struct work_struct *work)
+{
+ struct lpc32xx_udc *udc =
+ container_of(work, struct lpc32xx_udc, power_job);
+
+ isp1301_set_powerstate(udc, udc->poweron);
+}
+#endif
+
+/*
+ *
+ * USB protocol engine command/data read/write helper functions
+ *
+ */
+/* Issues a single command to the USB device state machine */
+static void udc_protocol_cmd_w(struct lpc32xx_udc *udc, u32 cmd)
+{
+ u32 pass = 0;
+ int to;
+
+ /* EP may lock on CLRI if this read isn't done */
+ u32 tmp = readl(USBD_DEVINTST(udc->udp_baseaddr));
+ (void) tmp;
+
+ while (pass == 0) {
+ writel(USBD_CCEMPTY, USBD_DEVINTCLR(udc->udp_baseaddr));
+
+ /* Write command code */
+ writel(cmd, USBD_CMDCODE(udc->udp_baseaddr));
+ to = 10000;
+ while (((readl(USBD_DEVINTST(udc->udp_baseaddr)) &
+ USBD_CCEMPTY) == 0) && (to > 0)) {
+ to--;
+ }
+
+ if (to > 0)
+ pass = 1;
+
+ cpu_relax();
+ }
+}
+
+/* Issues 2 commands (or command and data) to the USB device state machine */
+static inline void udc_protocol_cmd_data_w(struct lpc32xx_udc *udc, u32 cmd,
+ u32 data)
+{
+ udc_protocol_cmd_w(udc, cmd);
+ udc_protocol_cmd_w(udc, data);
+}
+
+/* Issues a single command to the USB device state machine and reads
+ * response data */
+static u32 udc_protocol_cmd_r(struct lpc32xx_udc *udc, u32 cmd)
+{
+ u32 tmp;
+ int to = 1000;
+
+ /* Write a command and read data from the protocol engine */
+ writel((USBD_CDFULL | USBD_CCEMPTY),
+ USBD_DEVINTCLR(udc->udp_baseaddr));
+
+ /* Write command code */
+ udc_protocol_cmd_w(udc, cmd);
+
+ tmp = readl(USBD_DEVINTST(udc->udp_baseaddr));
+ while ((!(readl(USBD_DEVINTST(udc->udp_baseaddr)) & USBD_CDFULL))
+ && (to > 0))
+ to--;
+ if (!to)
+ dev_dbg(udc->dev,
+ "Protocol engine didn't receive response (CDFULL)\n");
+
+ return readl(USBD_CMDDATA(udc->udp_baseaddr));
+}
+
+/*
+ *
+ * USB device interrupt mask support functions
+ *
+ */
+/* Enable one or more USB device interrupts */
+static inline void uda_enable_devint(struct lpc32xx_udc *udc, u32 devmask)
+{
+ udc->enabled_devints |= devmask;
+ writel(udc->enabled_devints, USBD_DEVINTEN(udc->udp_baseaddr));
+}
+
+/* Disable one or more USB device interrupts */
+static inline void uda_disable_devint(struct lpc32xx_udc *udc, u32 mask)
+{
+ udc->enabled_devints &= ~mask;
+ writel(udc->enabled_devints, USBD_DEVINTEN(udc->udp_baseaddr));
+}
+
+/* Clear one or more USB device interrupts */
+static inline void uda_clear_devint(struct lpc32xx_udc *udc, u32 mask)
+{
+ writel(mask, USBD_DEVINTCLR(udc->udp_baseaddr));
+}
+
+/*
+ *
+ * Endpoint interrupt disable/enable functions
+ *
+ */
+/* Enable one or more USB endpoint interrupts */
+static void uda_enable_hwepint(struct lpc32xx_udc *udc, u32 hwep)
+{
+ udc->enabled_hwepints |= (1 << hwep);
+ writel(udc->enabled_hwepints, USBD_EPINTEN(udc->udp_baseaddr));
+}
+
+/* Disable one or more USB endpoint interrupts */
+static void uda_disable_hwepint(struct lpc32xx_udc *udc, u32 hwep)
+{
+ udc->enabled_hwepints &= ~(1 << hwep);
+ writel(udc->enabled_hwepints, USBD_EPINTEN(udc->udp_baseaddr));
+}
+
+/* Clear one or more USB endpoint interrupts */
+static inline void uda_clear_hwepint(struct lpc32xx_udc *udc, u32 hwep)
+{
+ writel((1 << hwep), USBD_EPINTCLR(udc->udp_baseaddr));
+}
+
+/* Enable DMA for the HW channel */
+static inline void udc_ep_dma_enable(struct lpc32xx_udc *udc, u32 hwep)
+{
+ writel((1 << hwep), USBD_EPDMAEN(udc->udp_baseaddr));
+}
+
+/* Disable DMA for the HW channel */
+static inline void udc_ep_dma_disable(struct lpc32xx_udc *udc, u32 hwep)
+{
+ writel((1 << hwep), USBD_EPDMADIS(udc->udp_baseaddr));
+}
+
+/*
+ *
+ * Endpoint realize/unrealize functions
+ *
+ */
+/* Before an endpoint can be used, it needs to be realized
+ * in the USB protocol engine - this realizes the endpoint.
+ * The interrupt (FIFO or DMA) is not enabled with this function */
+static void udc_realize_hwep(struct lpc32xx_udc *udc, u32 hwep,
+ u32 maxpacket)
+{
+ int to = 1000;
+
+ writel(USBD_EP_RLZED, USBD_DEVINTCLR(udc->udp_baseaddr));
+ writel(hwep, USBD_EPIND(udc->udp_baseaddr));
+ udc->realized_eps |= (1 << hwep);
+ writel(udc->realized_eps, USBD_REEP(udc->udp_baseaddr));
+ writel(maxpacket, USBD_EPMAXPSIZE(udc->udp_baseaddr));
+
+ /* Wait until endpoint is realized in hardware */
+ while ((!(readl(USBD_DEVINTST(udc->udp_baseaddr)) &
+ USBD_EP_RLZED)) && (to > 0))
+ to--;
+ if (!to)
+ dev_dbg(udc->dev, "EP not correctly realized in hardware\n");
+
+ writel(USBD_EP_RLZED, USBD_DEVINTCLR(udc->udp_baseaddr));
+}
+
+/* Unrealize an EP */
+static void udc_unrealize_hwep(struct lpc32xx_udc *udc, u32 hwep)
+{
+ udc->realized_eps &= ~(1 << hwep);
+ writel(udc->realized_eps, USBD_REEP(udc->udp_baseaddr));
+}
+
+/*
+ *
+ * Endpoint support functions
+ *
+ */
+/* Select and clear endpoint interrupt */
+static u32 udc_selep_clrint(struct lpc32xx_udc *udc, u32 hwep)
+{
+ udc_protocol_cmd_w(udc, CMD_SEL_EP_CLRI(hwep));
+ return udc_protocol_cmd_r(udc, DAT_SEL_EP_CLRI(hwep));
+}
+
+/* Disables the endpoint in the USB protocol engine */
+static void udc_disable_hwep(struct lpc32xx_udc *udc, u32 hwep)
+{
+ udc_protocol_cmd_data_w(udc, CMD_SET_EP_STAT(hwep),
+ DAT_WR_BYTE(EP_STAT_DA));
+}
+
+/* Stalls the endpoint - endpoint will return STALL */
+static void udc_stall_hwep(struct lpc32xx_udc *udc, u32 hwep)
+{
+ udc_protocol_cmd_data_w(udc, CMD_SET_EP_STAT(hwep),
+ DAT_WR_BYTE(EP_STAT_ST));
+}
+
+/* Clear stall or reset endpoint */
+static void udc_clrstall_hwep(struct lpc32xx_udc *udc, u32 hwep)
+{
+ udc_protocol_cmd_data_w(udc, CMD_SET_EP_STAT(hwep),
+ DAT_WR_BYTE(0));
+}
+
+/* Select an endpoint for endpoint status, clear, validate */
+static void udc_select_hwep(struct lpc32xx_udc *udc, u32 hwep)
+{
+ udc_protocol_cmd_w(udc, CMD_SEL_EP(hwep));
+}
+
+/*
+ *
+ * Endpoint buffer management functions
+ *
+ */
+/* Clear the current endpoint's buffer */
+static void udc_clr_buffer_hwep(struct lpc32xx_udc *udc, u32 hwep)
+{
+ udc_select_hwep(udc, hwep);
+ udc_protocol_cmd_w(udc, CMD_CLR_BUF);
+}
+
+/* Validate the current endpoint's buffer */
+static void udc_val_buffer_hwep(struct lpc32xx_udc *udc, u32 hwep)
+{
+ udc_select_hwep(udc, hwep);
+ udc_protocol_cmd_w(udc, CMD_VALID_BUF);
+}
+
+static inline u32 udc_clearep_getsts(struct lpc32xx_udc *udc, u32 hwep)
+{
+ /* Clear EP interrupt */
+ uda_clear_hwepint(udc, hwep);
+ return udc_selep_clrint(udc, hwep);
+}
+
+/*
+ *
+ * USB EP DMA support
+ *
+ */
+/* Allocate a DMA Descriptor */
+static struct lpc32xx_usbd_dd_gad *udc_dd_alloc(struct lpc32xx_udc *udc)
+{
+ dma_addr_t dma;
+ struct lpc32xx_usbd_dd_gad *dd;
+
+ dd = (struct lpc32xx_usbd_dd_gad *) dma_pool_alloc(
+ udc->dd_cache, (GFP_KERNEL | GFP_DMA), &dma);
+ if (dd)
+ dd->this_dma = dma;
+
+ return dd;
+}
+
+/* Free a DMA Descriptor */
+static void udc_dd_free(struct lpc32xx_udc *udc, struct lpc32xx_usbd_dd_gad *dd)
+{
+ dma_pool_free(udc->dd_cache, dd, dd->this_dma);
+}
+
+/*
+ *
+ * USB setup and shutdown functions
+ *
+ */
+/* Enables or disables most of the USB system clocks when low power mode is
+ * needed. Clocks are typically started on a connection event, and disabled
+ * when a cable is disconnected */
+#define OTGOFF_CLK_MASK (AHB_M_CLOCK_ON | I2C_CLOCK_ON)
+static void udc_clk_set(struct lpc32xx_udc *udc, int enable)
+{
+ int to = 1000;
+
+ if (enable != 0) {
+ if (udc->clocked)
+ return;
+
+ udc->clocked = 1;
+
+ /* 48MHz PLL up */
+ clk_enable(udc->usb_pll_clk);
+
+ /* Enable the USB device clock */
+ writel(readl(USB_CTRL) | USB_DEV_NEED_CLK_EN,
+ USB_CTRL);
+
+ /* Set to enable all needed USB OTG clocks */
+ writel(USB_CLOCK_MASK, USB_OTG_CLK_CTRL(udc));
+
+ while (((readl(USB_OTG_CLK_STAT(udc)) & USB_CLOCK_MASK) !=
+ USB_CLOCK_MASK) && (to > 0))
+ to--;
+ if (!to)
+ dev_dbg(udc->dev, "Cannot enable USB OTG clocking\n");
+ } else {
+ if (!udc->clocked)
+ return;
+
+ udc->clocked = 0;
+
+ /* Never disable the USB_HCLK during normal operation */
+
+ /* 48MHz PLL dpwn */
+ clk_disable(udc->usb_pll_clk);
+
+ /* Enable the USB device clock */
+ writel(readl(USB_CTRL) & ~USB_DEV_NEED_CLK_EN,
+ USB_CTRL);
+
+ /* Set to enable all needed USB OTG clocks */
+ writel(OTGOFF_CLK_MASK, USB_OTG_CLK_CTRL(udc));
+
+ while (((readl(USB_OTG_CLK_STAT(udc)) &
+ OTGOFF_CLK_MASK) !=
+ OTGOFF_CLK_MASK) && (to > 0))
+ to--;
+ if (!to)
+ dev_dbg(udc->dev, "Cannot disable USB OTG clocking\n");
+ }
+}
+
+/* Set/reset USB device address */
+static void udc_set_address(struct lpc32xx_udc *udc, u32 addr)
+{
+ /* Address will be latched at the end of the status phase, or
+ latched immediately if function is called twice */
+ udc_protocol_cmd_data_w(udc, CMD_SET_ADDR,
+ DAT_WR_BYTE(DEV_EN | addr));
+}
+
+/* Setup up a IN request for DMA transfer - this consists of determining the
+ * list of DMA addresses for the transfer, allocating DMA Descriptors,
+ * installing the DD into the UDCA, and then enabling the DMA for that EP */
+static int udc_ep_in_req_dma(struct lpc32xx_udc *udc, struct lpc32xx_ep *ep)
+{
+ struct lpc32xx_request *req;
+ u32 hwep = ep->hwep_num;
+
+ ep->req_pending = 1;
+
+ /* There will always be a request waiting here */
+ req = list_entry(ep->queue.next, struct lpc32xx_request, queue);
+
+ /* Place the DD Descriptor into the UDCA */
+ udc->udca_v_base[hwep] = req->dd_desc_ptr->this_dma;
+
+ /* Enable DMA and interrupt for the HW EP */
+ udc_ep_dma_enable(udc, hwep);
+
+ /* Clear ZLP if last packet is not of MAXP size */
+ if (req->req.length % ep->ep.maxpacket)
+ req->send_zlp = 0;
+
+ return 0;
+}
+
+/* Setup up a OUT request for DMA transfer - this consists of determining the
+ * list of DMA addresses for the transfer, allocating DMA Descriptors,
+ * installing the DD into the UDCA, and then enabling the DMA for that EP */
+static int udc_ep_out_req_dma(struct lpc32xx_udc *udc, struct lpc32xx_ep *ep)
+{
+ struct lpc32xx_request *req;
+ u32 hwep = ep->hwep_num;
+
+ ep->req_pending = 1;
+
+ /* There will always be a request waiting here */
+ req = list_entry(ep->queue.next, struct lpc32xx_request, queue);
+
+ /* Place the DD Descriptor into the UDCA */
+ udc->udca_v_base[hwep] = req->dd_desc_ptr->this_dma;
+
+ /* Enable DMA and interrupt for the HW EP */
+ udc_ep_dma_enable(udc, hwep);
+ return 0;
+}
+
+static void udc_disable(struct lpc32xx_udc *udc)
+{
+ u32 i;
+
+ /* Disable device */
+ udc_protocol_cmd_data_w(udc, CMD_CFG_DEV, DAT_WR_BYTE(0));
+ udc_protocol_cmd_data_w(udc, CMD_SET_DEV_STAT, DAT_WR_BYTE(0));
+
+ /* Disable all device interrupts (including EP0) */
+ uda_disable_devint(udc, 0x3FF);
+
+ /* Disable and reset all endpoint interrupts */
+ for (i = 0; i < 32; i++) {
+ uda_disable_hwepint(udc, i);
+ uda_clear_hwepint(udc, i);
+ udc_disable_hwep(udc, i);
+ udc_unrealize_hwep(udc, i);
+ udc->udca_v_base[i] = 0;
+
+ /* Disable and clear all interrupts and DMA */
+ udc_ep_dma_disable(udc, i);
+ writel((1 << i), USBD_EOTINTCLR(udc->udp_baseaddr));
+ writel((1 << i), USBD_NDDRTINTCLR(udc->udp_baseaddr));
+ writel((1 << i), USBD_SYSERRTINTCLR(udc->udp_baseaddr));
+ writel((1 << i), USBD_DMARCLR(udc->udp_baseaddr));
+ }
+
+ /* Disable DMA interrupts */
+ writel(0, USBD_DMAINTEN(udc->udp_baseaddr));
+
+ writel(0, USBD_UDCAH(udc->udp_baseaddr));
+}
+
+static void udc_enable(struct lpc32xx_udc *udc)
+{
+ u32 i;
+ struct lpc32xx_ep *ep = &udc->ep[0];
+
+ /* Start with known state */
+ udc_disable(udc);
+
+ /* Enable device */
+ udc_protocol_cmd_data_w(udc, CMD_SET_DEV_STAT, DAT_WR_BYTE(DEV_CON));
+
+ /* EP interrupts on high priority, FRAME interrupt on low priority */
+ writel(USBD_EP_FAST, USBD_DEVINTPRI(udc->udp_baseaddr));
+ writel(0xFFFF, USBD_EPINTPRI(udc->udp_baseaddr));
+
+ /* Clear any pending device interrupts */
+ writel(0x3FF, USBD_DEVINTCLR(udc->udp_baseaddr));
+
+ /* Setup UDCA - not yet used (DMA) */
+ writel(udc->udca_p_base, USBD_UDCAH(udc->udp_baseaddr));
+
+ /* Only enable EP0 in and out for now, EP0 only works in FIFO mode */
+ for (i = 0; i <= 1; i++) {
+ udc_realize_hwep(udc, i, ep->ep.maxpacket);
+ uda_enable_hwepint(udc, i);
+ udc_select_hwep(udc, i);
+ udc_clrstall_hwep(udc, i);
+ udc_clr_buffer_hwep(udc, i);
+ }
+
+ /* Device interrupt setup */
+ uda_clear_devint(udc, (USBD_ERR_INT | USBD_DEV_STAT | USBD_EP_SLOW |
+ USBD_EP_FAST));
+ uda_enable_devint(udc, (USBD_ERR_INT | USBD_DEV_STAT | USBD_EP_SLOW |
+ USBD_EP_FAST));
+
+ /* Set device address to 0 - called twice to force a latch in the USB
+ engine without the need of a setup packet status closure */
+ udc_set_address(udc, 0);
+ udc_set_address(udc, 0);
+
+ /* Enable master DMA interrupts */
+ writel((USBD_SYS_ERR_INT | USBD_EOT_INT),
+ USBD_DMAINTEN(udc->udp_baseaddr));
+
+ udc->dev_status = 0;
+}
+
+/*
+ *
+ * USB device board specific events handled via callbacks
+ *
+ */
+/* Connection change event - notify board function of change */
+static void uda_power_event(struct lpc32xx_udc *udc, u32 conn)
+{
+ /* Just notify of a connection change event (optional) */
+ if (udc->board->conn_chgb != NULL)
+ udc->board->conn_chgb(conn);
+}
+
+/* Suspend/resume event - notify board function of change */
+static void uda_resm_susp_event(struct lpc32xx_udc *udc, u32 conn)
+{
+ /* Just notify of a Suspend/resume change event (optional) */
+ if (udc->board->susp_chgb != NULL)
+ udc->board->susp_chgb(conn);
+
+ if (conn)
+ udc->suspended = 0;
+ else
+ udc->suspended = 1;
+}
+
+/* Remote wakeup enable/disable - notify board function of change */
+static void uda_remwkp_cgh(struct lpc32xx_udc *udc)
+{
+ if (udc->board->rmwk_chgb != NULL)
+ udc->board->rmwk_chgb(udc->dev_status &
+ (1 << USB_DEVICE_REMOTE_WAKEUP));
+}
+
+/* Reads data from FIFO, adjusts for alignment and data size */
+static void udc_pop_fifo(struct lpc32xx_udc *udc, u8 *data, u32 bytes)
+{
+ int n, i, bl;
+ u16 *p16;
+ u32 *p32, tmp, cbytes;
+
+ /* Use optimal data transfer method based on source address and size */
+ switch (((u32) data) & 0x3) {
+ case 0: /* 32-bit aligned */
+ p32 = (u32 *) data;
+ cbytes = (bytes & ~0x3);
+
+ /* Copy 32-bit aligned data first */
+ for (n = 0; n < cbytes; n += 4)
+ *p32++ = readl(USBD_RXDATA(udc->udp_baseaddr));
+
+ /* Handle any remaining bytes */
+ bl = bytes - cbytes;
+ if (bl) {
+ tmp = readl(USBD_RXDATA(udc->udp_baseaddr));
+ for (n = 0; n < bl; n++)
+ data[cbytes + n] = ((tmp >> (n * 8)) & 0xFF);
+
+ }
+ break;
+
+ case 1: /* 8-bit aligned */
+ case 3:
+ /* Each byte has to be handled independently */
+ for (n = 0; n < bytes; n += 4) {
+ tmp = readl(USBD_RXDATA(udc->udp_baseaddr));
+
+ bl = bytes - n;
+ if (bl > 3)
+ bl = 3;
+
+ for (i = 0; i < bl; i++)
+ data[n + i] = (u8) ((tmp >> (n * 8)) & 0xFF);
+ }
+ break;
+
+ case 2: /* 16-bit aligned */
+ p16 = (u16 *) data;
+ cbytes = (bytes & ~0x3);
+
+ /* Copy 32-bit sized objects first with 16-bit alignment */
+ for (n = 0; n < cbytes; n += 4) {
+ tmp = readl(USBD_RXDATA(udc->udp_baseaddr));
+ *p16++ = (u16)(tmp & 0xFFFF);
+ *p16++ = (u16)((tmp >> 16) & 0xFFFF);
+ }
+
+ /* Handle any remaining bytes */
+ bl = bytes - cbytes;
+ if (bl) {
+ tmp = readl(USBD_RXDATA(udc->udp_baseaddr));
+ for (n = 0; n < bl; n++)
+ data[cbytes + n] = ((tmp >> (n * 8)) & 0xFF);
+ }
+ break;
+ }
+}
+
+/* Read data from the FIFO for an endpoint. This function is for endpoints (such
+ * as EP0) that don't use DMA. This function should only be called if a packet
+ * is known to be ready to read for the endpoint. Note that the endpoint must
+ * be selected in the protocol engine prior to this call. */
+static u32 udc_read_hwep(struct lpc32xx_udc *udc, u32 hwep, u32 *data,
+ u32 bytes)
+{
+ u32 tmpv;
+ int to = 1000;
+ u32 tmp, hwrep = ((hwep & 0x1E) << 1) | CTRL_RD_EN;
+
+ /* Setup read of endpoint */
+ writel(hwrep, USBD_CTRL(udc->udp_baseaddr));
+
+ /* Wait until packet is ready */
+ while ((((tmpv = readl(USBD_RXPLEN(udc->udp_baseaddr))) &
+ PKT_RDY) == 0) && (to > 0))
+ to--;
+ if (!to)
+ dev_dbg(udc->dev, "No packet ready on FIFO EP read\n");
+
+ /* Mask out count */
+ tmp = tmpv & PKT_LNGTH_MASK;
+ if (bytes < tmp)
+ tmp = bytes;
+
+ if ((tmp > 0) && (data != NULL))
+ udc_pop_fifo(udc, (u8 *) data, tmp);
+
+ writel(((hwep & 0x1E) << 1), USBD_CTRL(udc->udp_baseaddr));
+
+ /* Clear the buffer */
+ udc_clr_buffer_hwep(udc, hwep);
+
+ return tmp;
+}
+
+/* Stuffs data into the FIFO, adjusts for alignment and data size */
+static void udc_stuff_fifo(struct lpc32xx_udc *udc, u8 *data, u32 bytes)
+{
+ int n, i, bl;
+ u16 *p16;
+ u32 *p32, tmp, cbytes;
+
+ /* Use optimal data transfer method based on source address and size */
+ switch (((u32) data) & 0x3) {
+ case 0: /* 32-bit aligned */
+ p32 = (u32 *) data;
+ cbytes = (bytes & ~0x3);
+
+ /* Copy 32-bit aligned data first */
+ for (n = 0; n < cbytes; n += 4)
+ writel(*p32++, USBD_TXDATA(udc->udp_baseaddr));
+
+ /* Handle any remaining bytes */
+ bl = bytes - cbytes;
+ if (bl) {
+ tmp = 0;
+ for (n = 0; n < bl; n++)
+ tmp |= data[cbytes + n] << (n * 8);
+
+ writel(tmp, USBD_TXDATA(udc->udp_baseaddr));
+ }
+ break;
+
+ case 1: /* 8-bit aligned */
+ case 3:
+ /* Each byte has to be handled independently */
+ for (n = 0; n < bytes; n += 4) {
+ bl = bytes - n;
+ if (bl > 4)
+ bl = 4;
+
+ tmp = 0;
+ for (i = 0; i < bl; i++)
+ tmp |= data[n + i] << (i * 8);
+
+ writel(tmp, USBD_TXDATA(udc->udp_baseaddr));
+ }
+ break;
+
+ case 2: /* 16-bit aligned */
+ p16 = (u16 *) data;
+ cbytes = (bytes & ~0x3);
+
+ /* Copy 32-bit aligned data first */
+ for (n = 0; n < cbytes; n += 4) {
+ tmp = *p16++ & 0xFFFF;
+ tmp |= (*p16++ & 0xFFFF) << 16;
+ writel(tmp, USBD_TXDATA(udc->udp_baseaddr));
+ }
+
+ /* Handle any remaining bytes */
+ bl = bytes - cbytes;
+ if (bl) {
+ tmp = 0;
+ for (n = 0; n < bl; n++)
+ tmp |= data[cbytes + n] << (n * 8);
+
+ writel(tmp, USBD_TXDATA(udc->udp_baseaddr));
+ }
+ break;
+ }
+}
+
+/* Write data to the FIFO for an endpoint. This function is for endpoints (such
+ * as EP0) that don't use DMA. Note that the endpoint must be selected in the
+ * protocol engine prior to this call. */
+static void udc_write_hwep(struct lpc32xx_udc *udc, u32 hwep, u32 *data,
+ u32 bytes)
+{
+ u32 hwwep = ((hwep & 0x1E) << 1) | CTRL_WR_EN;
+
+ if ((bytes > 0) && (data == NULL))
+ return;
+
+ /* Setup write of endpoint */
+ writel(hwwep, USBD_CTRL(udc->udp_baseaddr));
+
+ writel(bytes, USBD_TXPLEN(udc->udp_baseaddr));
+
+ /* Need at least 1 byte to trigger TX */
+ if (bytes == 0)
+ writel(0, USBD_TXDATA(udc->udp_baseaddr));
+ else
+ udc_stuff_fifo(udc, (u8 *) data, bytes);
+
+ writel(((hwep & 0x1E) << 1), USBD_CTRL(udc->udp_baseaddr));
+
+ udc_val_buffer_hwep(udc, hwep);
+}
+
+/* USB device reset - resets USB to a default state with just EP0
+ enabled */
+static void uda_usb_reset(struct lpc32xx_udc *udc)
+{
+ u32 i = 0;
+ /* Re-init device controller and EP0 */
+ udc_enable(udc);
+ udc->gadget.speed = USB_SPEED_FULL;
+
+ for (i = 1; i < NUM_ENDPOINTS; i++) {
+ struct lpc32xx_ep *ep = &udc->ep[i];
+ ep->req_pending = 0;
+ }
+}
+
+/* Send a ZLP on EP0 */
+static void udc_ep0_send_zlp(struct lpc32xx_udc *udc)
+{
+ udc_write_hwep(udc, EP_IN, NULL, 0);
+}
+
+/* Get current frame number */
+static u16 udc_get_current_frame(struct lpc32xx_udc *udc)
+{
+ u16 flo, fhi;
+
+ udc_protocol_cmd_w(udc, CMD_RD_FRAME);
+ flo = (u16) udc_protocol_cmd_r(udc, DAT_RD_FRAME);
+ fhi = (u16) udc_protocol_cmd_r(udc, DAT_RD_FRAME);
+
+ return (fhi << 8) | flo;
+}
+
+/* Set the device as configured - enables all endpoints */
+static inline void udc_set_device_configured(struct lpc32xx_udc *udc)
+{
+ udc_protocol_cmd_data_w(udc, CMD_CFG_DEV, DAT_WR_BYTE(CONF_DVICE));
+}
+
+/* Set the device as unconfigured - disables all endpoints */
+static inline void udc_set_device_unconfigured(struct lpc32xx_udc *udc)
+{
+ udc_protocol_cmd_data_w(udc, CMD_CFG_DEV, DAT_WR_BYTE(0));
+}
+
+/* reinit == restore initial software state */
+static void udc_reinit(struct lpc32xx_udc *udc)
+{
+ u32 i;
+
+ INIT_LIST_HEAD(&udc->gadget.ep_list);
+ INIT_LIST_HEAD(&udc->gadget.ep0->ep_list);
+
+ for (i = 0; i < NUM_ENDPOINTS; i++) {
+ struct lpc32xx_ep *ep = &udc->ep[i];
+
+ if (i != 0)
+ list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list);
+ ep->desc = NULL;
+ ep->ep.maxpacket = ep->maxpacket;
+ INIT_LIST_HEAD(&ep->queue);
+ ep->req_pending = 0;
+ }
+
+ udc->ep0state = WAIT_FOR_SETUP;
+}
+
+/* Must be called with lock */
+static void done(struct lpc32xx_ep *ep, struct lpc32xx_request *req, int status)
+{
+ struct lpc32xx_udc *udc = ep->udc;
+
+ list_del_init(&req->queue);
+ if (req->req.status == -EINPROGRESS)
+ req->req.status = status;
+ else
+ status = req->req.status;
+
+ if (ep->lep) {
+ enum dma_data_direction direction;
+
+ if (ep->is_in)
+ direction = DMA_TO_DEVICE;
+ else
+ direction = DMA_FROM_DEVICE;
+
+ if (req->mapped) {
+ dma_unmap_single(ep->udc->gadget.dev.parent,
+ req->req.dma, req->req.length,
+ direction);
+ req->req.dma = 0;
+ req->mapped = 0;
+ } else
+ dma_sync_single_for_cpu(ep->udc->gadget.dev.parent,
+ req->req.dma, req->req.length,
+ direction);
+
+ /* Free DDs */
+ udc_dd_free(udc, req->dd_desc_ptr);
+ }
+
+ if (status && status != -ESHUTDOWN)
+ ep_dbg(ep, "%s done %p, status %d\n", ep->ep.name, req, status);
+
+ ep->req_pending = 0;
+ spin_unlock(&udc->lock);
+ req->req.complete(&ep->ep, &req->req);
+ spin_lock(&udc->lock);
+}
+
+/* Must be called with lock */
+static void nuke(struct lpc32xx_ep *ep, int status)
+{
+ struct lpc32xx_request *req;
+
+ while (!list_empty(&ep->queue)) {
+ req = list_entry(ep->queue.next, struct lpc32xx_request, queue);
+ done(ep, req, status);
+ }
+
+ if (ep->desc && status == -ESHUTDOWN) {
+ uda_disable_hwepint(ep->udc, ep->hwep_num);
+ udc_disable_hwep(ep->udc, ep->hwep_num);
+ }
+}
+
+/* IN endpoint 0 transfer */
+static int udc_ep0_in_req(struct lpc32xx_udc *udc)
+{
+ struct lpc32xx_request *req;
+ struct lpc32xx_ep *ep0 = &udc->ep[0];
+ u32 tsend, ts = 0;
+
+ if (list_empty(&ep0->queue))
+ /* Nothing to send */
+ return 0;
+ else
+ req = list_entry(ep0->queue.next, struct lpc32xx_request,
+ queue);
+
+ tsend = ts = req->req.length - req->req.actual;
+ if (ts == 0) {
+ /* Send a ZLP */
+ udc_ep0_send_zlp(udc);
+ done(ep0, req, 0);
+ return 1;
+ } else if (ts > ep0->ep.maxpacket)
+ ts = ep0->ep.maxpacket; /* Just send what we can */
+
+ /* Write data to the EP0 FIFO and start transfer */
+ udc_write_hwep(udc, EP_IN, (req->req.buf + req->req.actual), ts);
+
+ /* Increment data pointer */
+ req->req.actual += ts;
+
+ if (tsend >= ep0->ep.maxpacket)
+ return 0; /* Stay in data transfer state */
+
+ /* Transfer request is complete */
+ udc->ep0state = WAIT_FOR_SETUP;
+ done(ep0, req, 0);
+ return 1;
+}
+
+/* OUT endpoint 0 transfer */
+static int udc_ep0_out_req(struct lpc32xx_udc *udc)
+{
+ struct lpc32xx_request *req;
+ struct lpc32xx_ep *ep0 = &udc->ep[0];
+ u32 tr, bufferspace;
+
+ if (list_empty(&ep0->queue))
+ return 0;
+ else
+ req = list_entry(ep0->queue.next, struct lpc32xx_request,
+ queue);
+
+ if (req) {
+ if (req->req.length == 0) {
+ /* Just dequeue request */
+ done(ep0, req, 0);
+ udc->ep0state = WAIT_FOR_SETUP;
+ return 1;
+ }
+
+ /* Get data from FIFO */
+ bufferspace = req->req.length - req->req.actual;
+ if (bufferspace > ep0->ep.maxpacket)
+ bufferspace = ep0->ep.maxpacket;
+
+ /* Copy data to buffer */
+ prefetchw(req->req.buf + req->req.actual);
+ tr = udc_read_hwep(udc, EP_OUT, req->req.buf + req->req.actual,
+ bufferspace);
+ req->req.actual += bufferspace;
+
+ if (tr < ep0->ep.maxpacket) {
+ /* This is the last packet */
+ done(ep0, req, 0);
+ udc->ep0state = WAIT_FOR_SETUP;
+ return 1;
+ }
+ }
+
+ return 0;
+}
+
+/* Must be called with lock */
+static void stop_activity(struct lpc32xx_udc *udc)
+{
+ struct usb_gadget_driver *driver = udc->driver;
+ int i;
+
+ if (udc->gadget.speed == USB_SPEED_UNKNOWN)
+ driver = NULL;
+
+ udc->gadget.speed = USB_SPEED_UNKNOWN;
+ udc->suspended = 0;
+
+ for (i = 0; i < NUM_ENDPOINTS; i++) {
+ struct lpc32xx_ep *ep = &udc->ep[i];
+ nuke(ep, -ESHUTDOWN);
+ }
+ if (driver) {
+ spin_unlock(&udc->lock);
+ driver->disconnect(&udc->gadget);
+ spin_lock(&udc->lock);
+ }
+
+ isp1301_pullup_enable(udc, 0, 0);
+ udc_disable(udc);
+ udc_reinit(udc);
+}
+
+/*
+ * Activate or kill host pullup
+ * Can be called with or without lock
+ */
+static void pullup(struct lpc32xx_udc *udc, int is_on)
+{
+ if (!udc->clocked)
+ return;
+
+ if (!udc->enabled || !udc->vbus)
+ is_on = 0;
+
+ if (is_on != udc->pullup)
+ isp1301_pullup_enable(udc, is_on, 0);
+}
+
+/* Must be called without lock */
+static int lpc32xx_ep_disable(struct usb_ep *_ep)
+{
+ struct lpc32xx_ep *ep = container_of(_ep, struct lpc32xx_ep, ep);
+ struct lpc32xx_udc *udc = ep->udc;
+ unsigned long flags;
+
+ if ((ep->hwep_num_base == 0) || (ep->hwep_num == 0))
+ return -EINVAL;
+ spin_lock_irqsave(&udc->lock, flags);
+
+ nuke(ep, -ESHUTDOWN);
+
+ /* restore the endpoint's pristine config */
+ ep->desc = NULL;
+
+ /* Clear all DMA statuses for this EP */
+ udc_ep_dma_disable(udc, ep->hwep_num);
+ writel(1 << ep->hwep_num, USBD_EOTINTCLR(udc->udp_baseaddr));
+ writel(1 << ep->hwep_num, USBD_NDDRTINTCLR(udc->udp_baseaddr));
+ writel(1 << ep->hwep_num, USBD_SYSERRTINTCLR(udc->udp_baseaddr));
+ writel(1 << ep->hwep_num, USBD_DMARCLR(udc->udp_baseaddr));
+
+ /* Remove the DD pointer in the UDCA */
+ udc->udca_v_base[ep->hwep_num] = 0;
+
+ /* Disable and reset endpoint and interrupt */
+ uda_clear_hwepint(udc, ep->hwep_num);
+ udc_unrealize_hwep(udc, ep->hwep_num);
+
+ ep->hwep_num = 0;
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ atomic_dec(&udc->enabled_ep_cnt);
+ wake_up(&udc->ep_disable_wait_queue);
+
+ return 0;
+}
+
+/* Must be called without lock */
+static int lpc32xx_ep_enable(struct usb_ep *_ep,
+ const struct usb_endpoint_descriptor *desc)
+{
+ struct lpc32xx_ep *ep = container_of(_ep, struct lpc32xx_ep, ep);
+ struct lpc32xx_udc *udc = ep->udc;
+ u16 maxpacket;
+ u32 tmp;
+ unsigned long flags;
+
+ /* Verify EP data */
+ if ((!_ep) || (!ep) || (!desc) || (ep->desc) ||
+ (desc->bDescriptorType != USB_DT_ENDPOINT)) {
+ dev_dbg(udc->dev, "bad ep or descriptor\n");
+ return -EINVAL;
+ }
+ maxpacket = usb_endpoint_maxp(desc);
+ if ((maxpacket == 0) || (maxpacket > ep->maxpacket)) {
+ dev_dbg(udc->dev, "bad ep descriptor's packet size\n");
+ return -EINVAL;
+ }
+
+ /* Don't touch EP0 */
+ if (ep->hwep_num_base == 0) {
+ dev_dbg(udc->dev, "Can't re-enable EP0!!!\n");
+ return -EINVAL;
+ }
+
+ /* Is driver ready? */
+ if ((!udc->driver) || (udc->gadget.speed == USB_SPEED_UNKNOWN)) {
+ dev_dbg(udc->dev, "bogus device state\n");
+ return -ESHUTDOWN;
+ }
+
+ tmp = desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK;
+ switch (tmp) {
+ case USB_ENDPOINT_XFER_CONTROL:
+ return -EINVAL;
+
+ case USB_ENDPOINT_XFER_INT:
+ if (maxpacket > ep->maxpacket) {
+ dev_dbg(udc->dev,
+ "Bad INT endpoint maxpacket %d\n", maxpacket);
+ return -EINVAL;
+ }
+ break;
+
+ case USB_ENDPOINT_XFER_BULK:
+ switch (maxpacket) {
+ case 8:
+ case 16:
+ case 32:
+ case 64:
+ break;
+
+ default:
+ dev_dbg(udc->dev,
+ "Bad BULK endpoint maxpacket %d\n", maxpacket);
+ return -EINVAL;
+ }
+ break;
+
+ case USB_ENDPOINT_XFER_ISOC:
+ break;
+ }
+ spin_lock_irqsave(&udc->lock, flags);
+
+ /* Initialize endpoint to match the selected descriptor */
+ ep->is_in = (desc->bEndpointAddress & USB_DIR_IN) != 0;
+ ep->desc = desc;
+ ep->ep.maxpacket = maxpacket;
+
+ /* Map hardware endpoint from base and direction */
+ if (ep->is_in)
+ /* IN endpoints are offset 1 from the OUT endpoint */
+ ep->hwep_num = ep->hwep_num_base + EP_IN;
+ else
+ ep->hwep_num = ep->hwep_num_base;
+
+ ep_dbg(ep, "EP enabled: %s, HW:%d, MP:%d IN:%d\n", ep->ep.name,
+ ep->hwep_num, maxpacket, (ep->is_in == 1));
+
+ /* Realize the endpoint, interrupt is enabled later when
+ * buffers are queued, IN EPs will NAK until buffers are ready */
+ udc_realize_hwep(udc, ep->hwep_num, ep->ep.maxpacket);
+ udc_clr_buffer_hwep(udc, ep->hwep_num);
+ uda_disable_hwepint(udc, ep->hwep_num);
+ udc_clrstall_hwep(udc, ep->hwep_num);
+
+ /* Clear all DMA statuses for this EP */
+ udc_ep_dma_disable(udc, ep->hwep_num);
+ writel(1 << ep->hwep_num, USBD_EOTINTCLR(udc->udp_baseaddr));
+ writel(1 << ep->hwep_num, USBD_NDDRTINTCLR(udc->udp_baseaddr));
+ writel(1 << ep->hwep_num, USBD_SYSERRTINTCLR(udc->udp_baseaddr));
+ writel(1 << ep->hwep_num, USBD_DMARCLR(udc->udp_baseaddr));
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ atomic_inc(&udc->enabled_ep_cnt);
+ return 0;
+}
+
+/*
+ * Allocate a USB request list
+ * Can be called with or without lock
+ */
+static struct usb_request *lpc32xx_ep_alloc_request(struct usb_ep *_ep,
+ gfp_t gfp_flags)
+{
+ struct lpc32xx_request *req;
+
+ req = kzalloc(sizeof(struct lpc32xx_request), gfp_flags);
+ if (!req)
+ return NULL;
+
+ INIT_LIST_HEAD(&req->queue);
+ return &req->req;
+}
+
+/*
+ * De-allocate a USB request list
+ * Can be called with or without lock
+ */
+static void lpc32xx_ep_free_request(struct usb_ep *_ep,
+ struct usb_request *_req)
+{
+ struct lpc32xx_request *req;
+
+ req = container_of(_req, struct lpc32xx_request, req);
+ BUG_ON(!list_empty(&req->queue));
+ kfree(req);
+}
+
+/* Must be called without lock */
+static int lpc32xx_ep_queue(struct usb_ep *_ep,
+ struct usb_request *_req, gfp_t gfp_flags)
+{
+ struct lpc32xx_request *req;
+ struct lpc32xx_ep *ep;
+ struct lpc32xx_udc *udc;
+ unsigned long flags;
+ int status = 0;
+
+ req = container_of(_req, struct lpc32xx_request, req);
+ ep = container_of(_ep, struct lpc32xx_ep, ep);
+
+ if (!_req || !_req->complete || !_req->buf ||
+ !list_empty(&req->queue))
+ return -EINVAL;
+
+ udc = ep->udc;
+
+ if (!_ep || (!ep->desc && ep->hwep_num_base != 0)) {
+ dev_dbg(udc->dev, "invalid ep\n");
+ return -EINVAL;
+ }
+
+
+ if ((!udc) || (!udc->driver) ||
+ (udc->gadget.speed == USB_SPEED_UNKNOWN)) {
+ dev_dbg(udc->dev, "invalid device\n");
+ return -EINVAL;
+ }
+
+ if (ep->lep) {
+ enum dma_data_direction direction;
+ struct lpc32xx_usbd_dd_gad *dd;
+
+ /* Map DMA pointer */
+ if (ep->is_in)
+ direction = DMA_TO_DEVICE;
+ else
+ direction = DMA_FROM_DEVICE;
+
+ if (req->req.dma == 0) {
+ req->req.dma = dma_map_single(
+ ep->udc->gadget.dev.parent,
+ req->req.buf, req->req.length, direction);
+ req->mapped = 1;
+ } else {
+ dma_sync_single_for_device(
+ ep->udc->gadget.dev.parent, req->req.dma,
+ req->req.length, direction);
+ req->mapped = 0;
+ }
+
+ /* For the request, build a list of DDs */
+ dd = udc_dd_alloc(udc);
+ if (!dd) {
+ /* Error allocating DD */
+ return -ENOMEM;
+ }
+ req->dd_desc_ptr = dd;
+
+ /* Setup the DMA descriptor */
+ dd->dd_next_phy = dd->dd_next_v = 0;
+ dd->dd_buffer_addr = req->req.dma;
+ dd->dd_status = 0;
+
+ /* Special handling for ISO EPs */
+ if (ep->eptype == EP_ISO_TYPE) {
+ dd->dd_setup = DD_SETUP_ISO_EP |
+ DD_SETUP_PACKETLEN(0) |
+ DD_SETUP_DMALENBYTES(1);
+ dd->dd_iso_ps_mem_addr = dd->this_dma + 24;
+ if (ep->is_in)
+ dd->iso_status[0] = req->req.length;
+ else
+ dd->iso_status[0] = 0;
+ } else
+ dd->dd_setup = DD_SETUP_PACKETLEN(ep->ep.maxpacket) |
+ DD_SETUP_DMALENBYTES(req->req.length);
+ }
+
+ ep_dbg(ep, "%s queue req %p len %d buf %p (in=%d) z=%d\n", _ep->name,
+ _req, _req->length, _req->buf, ep->is_in, _req->zero);
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ _req->status = -EINPROGRESS;
+ _req->actual = 0;
+ req->send_zlp = _req->zero;
+
+ /* Kickstart empty queues */
+ if (list_empty(&ep->queue)) {
+ list_add_tail(&req->queue, &ep->queue);
+
+ if (ep->hwep_num_base == 0) {
+ /* Handle expected data direction */
+ if (ep->is_in) {
+ /* IN packet to host */
+ udc->ep0state = DATA_IN;
+ status = udc_ep0_in_req(udc);
+ } else {
+ /* OUT packet from host */
+ udc->ep0state = DATA_OUT;
+ status = udc_ep0_out_req(udc);
+ }
+ } else if (ep->is_in) {
+ /* IN packet to host and kick off transfer */
+ if (!ep->req_pending)
+ udc_ep_in_req_dma(udc, ep);
+ } else
+ /* OUT packet from host and kick off list */
+ if (!ep->req_pending)
+ udc_ep_out_req_dma(udc, ep);
+ } else
+ list_add_tail(&req->queue, &ep->queue);
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ return (status < 0) ? status : 0;
+}
+
+/* Must be called without lock */
+static int lpc32xx_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req)
+{
+ struct lpc32xx_ep *ep;
+ struct lpc32xx_request *req;
+ unsigned long flags;
+
+ ep = container_of(_ep, struct lpc32xx_ep, ep);
+ if (!_ep || ep->hwep_num_base == 0)
+ return -EINVAL;
+
+ spin_lock_irqsave(&ep->udc->lock, flags);
+
+ /* make sure it's actually queued on this endpoint */
+ list_for_each_entry(req, &ep->queue, queue) {
+ if (&req->req == _req)
+ break;
+ }
+ if (&req->req != _req) {
+ spin_unlock_irqrestore(&ep->udc->lock, flags);
+ return -EINVAL;
+ }
+
+ done(ep, req, -ECONNRESET);
+
+ spin_unlock_irqrestore(&ep->udc->lock, flags);
+
+ return 0;
+}
+
+/* Must be called without lock */
+static int lpc32xx_ep_set_halt(struct usb_ep *_ep, int value)
+{
+ struct lpc32xx_ep *ep = container_of(_ep, struct lpc32xx_ep, ep);
+ struct lpc32xx_udc *udc = ep->udc;
+ unsigned long flags;
+
+ if ((!ep) || (ep->desc == NULL) || (ep->hwep_num <= 1))
+ return -EINVAL;
+
+ /* Don't halt an IN EP */
+ if (ep->is_in)
+ return -EAGAIN;
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ if (value == 1) {
+ /* stall */
+ udc_protocol_cmd_data_w(udc, CMD_SET_EP_STAT(ep->hwep_num),
+ DAT_WR_BYTE(EP_STAT_ST));
+ } else {
+ /* End stall */
+ ep->wedge = 0;
+ udc_protocol_cmd_data_w(udc, CMD_SET_EP_STAT(ep->hwep_num),
+ DAT_WR_BYTE(0));
+ }
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ return 0;
+}
+
+/* set the halt feature and ignores clear requests */
+static int lpc32xx_ep_set_wedge(struct usb_ep *_ep)
+{
+ struct lpc32xx_ep *ep = container_of(_ep, struct lpc32xx_ep, ep);
+
+ if (!_ep || !ep->udc)
+ return -EINVAL;
+
+ ep->wedge = 1;
+
+ return usb_ep_set_halt(_ep);
+}
+
+static const struct usb_ep_ops lpc32xx_ep_ops = {
+ .enable = lpc32xx_ep_enable,
+ .disable = lpc32xx_ep_disable,
+ .alloc_request = lpc32xx_ep_alloc_request,
+ .free_request = lpc32xx_ep_free_request,
+ .queue = lpc32xx_ep_queue,
+ .dequeue = lpc32xx_ep_dequeue,
+ .set_halt = lpc32xx_ep_set_halt,
+ .set_wedge = lpc32xx_ep_set_wedge,
+};
+
+/* Send a ZLP on a non-0 IN EP */
+void udc_send_in_zlp(struct lpc32xx_udc *udc, struct lpc32xx_ep *ep)
+{
+ /* Clear EP status */
+ udc_clearep_getsts(udc, ep->hwep_num);
+
+ /* Send ZLP via FIFO mechanism */
+ udc_write_hwep(udc, ep->hwep_num, NULL, 0);
+}
+
+/*
+ * Handle EP completion for ZLP
+ * This function will only be called when a delayed ZLP needs to be sent out
+ * after a DMA transfer has filled both buffers.
+ */
+void udc_handle_eps(struct lpc32xx_udc *udc, struct lpc32xx_ep *ep)
+{
+ u32 epstatus;
+ struct lpc32xx_request *req;
+
+ if (ep->hwep_num <= 0)
+ return;
+
+ uda_clear_hwepint(udc, ep->hwep_num);
+
+ /* If this interrupt isn't enabled, return now */
+ if (!(udc->enabled_hwepints & (1 << ep->hwep_num)))
+ return;
+
+ /* Get endpoint status */
+ epstatus = udc_clearep_getsts(udc, ep->hwep_num);
+
+ /*
+ * This should never happen, but protect against writing to the
+ * buffer when full.
+ */
+ if (epstatus & EP_SEL_F)
+ return;
+
+ if (ep->is_in) {
+ udc_send_in_zlp(udc, ep);
+ uda_disable_hwepint(udc, ep->hwep_num);
+ } else
+ return;
+
+ /* If there isn't a request waiting, something went wrong */
+ req = list_entry(ep->queue.next, struct lpc32xx_request, queue);
+ if (req) {
+ done(ep, req, 0);
+
+ /* Start another request if ready */
+ if (!list_empty(&ep->queue)) {
+ if (ep->is_in)
+ udc_ep_in_req_dma(udc, ep);
+ else
+ udc_ep_out_req_dma(udc, ep);
+ } else
+ ep->req_pending = 0;
+ }
+}
+
+
+/* DMA end of transfer completion */
+static void udc_handle_dma_ep(struct lpc32xx_udc *udc, struct lpc32xx_ep *ep)
+{
+ u32 status, epstatus;
+ struct lpc32xx_request *req;
+ struct lpc32xx_usbd_dd_gad *dd;
+
+#ifdef CONFIG_USB_GADGET_DEBUG_FILES
+ ep->totalints++;
+#endif
+
+ req = list_entry(ep->queue.next, struct lpc32xx_request, queue);
+ if (!req) {
+ ep_err(ep, "DMA interrupt on no req!\n");
+ return;
+ }
+ dd = req->dd_desc_ptr;
+
+ /* DMA descriptor should always be retired for this call */
+ if (!(dd->dd_status & DD_STATUS_DD_RETIRED))
+ ep_warn(ep, "DMA descriptor did not retire\n");
+
+ /* Disable DMA */
+ udc_ep_dma_disable(udc, ep->hwep_num);
+ writel((1 << ep->hwep_num), USBD_EOTINTCLR(udc->udp_baseaddr));
+ writel((1 << ep->hwep_num), USBD_NDDRTINTCLR(udc->udp_baseaddr));
+
+ /* System error? */
+ if (readl(USBD_SYSERRTINTST(udc->udp_baseaddr)) &
+ (1 << ep->hwep_num)) {
+ writel((1 << ep->hwep_num),
+ USBD_SYSERRTINTCLR(udc->udp_baseaddr));
+ ep_err(ep, "AHB critical error!\n");
+ ep->req_pending = 0;
+
+ /* The error could have occurred on a packet of a multipacket
+ * transfer, so recovering the transfer is not possible. Close
+ * the request with an error */
+ done(ep, req, -ECONNABORTED);
+ return;
+ }
+
+ /* Handle the current DD's status */
+ status = dd->dd_status;
+ switch (status & DD_STATUS_STS_MASK) {
+ case DD_STATUS_STS_NS:
+ /* DD not serviced? This shouldn't happen! */
+ ep->req_pending = 0;
+ ep_err(ep, "DMA critical EP error: DD not serviced (0x%x)!\n",
+ status);
+
+ done(ep, req, -ECONNABORTED);
+ return;
+
+ case DD_STATUS_STS_BS:
+ /* Interrupt only fires on EOT - This shouldn't happen! */
+ ep->req_pending = 0;
+ ep_err(ep, "DMA critical EP error: EOT prior to service completion (0x%x)!\n",
+ status);
+ done(ep, req, -ECONNABORTED);
+ return;
+
+ case DD_STATUS_STS_NC:
+ case DD_STATUS_STS_DUR:
+ /* Really just a short packet, not an underrun */
+ /* This is a good status and what we expect */
+ break;
+
+ default:
+ /* Data overrun, system error, or unknown */
+ ep->req_pending = 0;
+ ep_err(ep, "DMA critical EP error: System error (0x%x)!\n",
+ status);
+ done(ep, req, -ECONNABORTED);
+ return;
+ }
+
+ /* ISO endpoints are handled differently */
+ if (ep->eptype == EP_ISO_TYPE) {
+ if (ep->is_in)
+ req->req.actual = req->req.length;
+ else
+ req->req.actual = dd->iso_status[0] & 0xFFFF;
+ } else
+ req->req.actual += DD_STATUS_CURDMACNT(status);
+
+ /* Send a ZLP if necessary. This will be done for non-int
+ * packets which have a size that is a divisor of MAXP */
+ if (req->send_zlp) {
+ /*
+ * If at least 1 buffer is available, send the ZLP now.
+ * Otherwise, the ZLP send needs to be deferred until a
+ * buffer is available.
+ */
+ if (udc_clearep_getsts(udc, ep->hwep_num) & EP_SEL_F) {
+ udc_clearep_getsts(udc, ep->hwep_num);
+ uda_enable_hwepint(udc, ep->hwep_num);
+ epstatus = udc_clearep_getsts(udc, ep->hwep_num);
+
+ /* Let the EP interrupt handle the ZLP */
+ return;
+ } else
+ udc_send_in_zlp(udc, ep);
+ }
+
+ /* Transfer request is complete */
+ done(ep, req, 0);
+
+ /* Start another request if ready */
+ udc_clearep_getsts(udc, ep->hwep_num);
+ if (!list_empty((&ep->queue))) {
+ if (ep->is_in)
+ udc_ep_in_req_dma(udc, ep);
+ else
+ udc_ep_out_req_dma(udc, ep);
+ } else
+ ep->req_pending = 0;
+
+}
+
+/*
+ *
+ * Endpoint 0 functions
+ *
+ */
+static void udc_handle_dev(struct lpc32xx_udc *udc)
+{
+ u32 tmp;
+
+ udc_protocol_cmd_w(udc, CMD_GET_DEV_STAT);
+ tmp = udc_protocol_cmd_r(udc, DAT_GET_DEV_STAT);
+
+ if (tmp & DEV_RST)
+ uda_usb_reset(udc);
+ else if (tmp & DEV_CON_CH)
+ uda_power_event(udc, (tmp & DEV_CON));
+ else if (tmp & DEV_SUS_CH) {
+ if (tmp & DEV_SUS) {
+ if (udc->vbus == 0)
+ stop_activity(udc);
+ else if ((udc->gadget.speed != USB_SPEED_UNKNOWN) &&
+ udc->driver) {
+ /* Power down transceiver */
+ udc->poweron = 0;
+ schedule_work(&udc->pullup_job);
+ uda_resm_susp_event(udc, 1);
+ }
+ } else if ((udc->gadget.speed != USB_SPEED_UNKNOWN) &&
+ udc->driver && udc->vbus) {
+ uda_resm_susp_event(udc, 0);
+ /* Power up transceiver */
+ udc->poweron = 1;
+ schedule_work(&udc->pullup_job);
+ }
+ }
+}
+
+static int udc_get_status(struct lpc32xx_udc *udc, u16 reqtype, u16 wIndex)
+{
+ struct lpc32xx_ep *ep;
+ u32 ep0buff = 0, tmp;
+
+ switch (reqtype & USB_RECIP_MASK) {
+ case USB_RECIP_INTERFACE:
+ break; /* Not supported */
+
+ case USB_RECIP_DEVICE:
+ ep0buff = (udc->selfpowered << USB_DEVICE_SELF_POWERED);
+ if (udc->dev_status & (1 << USB_DEVICE_REMOTE_WAKEUP))
+ ep0buff |= (1 << USB_DEVICE_REMOTE_WAKEUP);
+ break;
+
+ case USB_RECIP_ENDPOINT:
+ tmp = wIndex & USB_ENDPOINT_NUMBER_MASK;
+ ep = &udc->ep[tmp];
+ if ((tmp == 0) || (tmp >= NUM_ENDPOINTS) || (tmp && !ep->desc))
+ return -EOPNOTSUPP;
+
+ if (wIndex & USB_DIR_IN) {
+ if (!ep->is_in)
+ return -EOPNOTSUPP; /* Something's wrong */
+ } else if (ep->is_in)
+ return -EOPNOTSUPP; /* Not an IN endpoint */
+
+ /* Get status of the endpoint */
+ udc_protocol_cmd_w(udc, CMD_SEL_EP(ep->hwep_num));
+ tmp = udc_protocol_cmd_r(udc, DAT_SEL_EP(ep->hwep_num));
+
+ if (tmp & EP_SEL_ST)
+ ep0buff = (1 << USB_ENDPOINT_HALT);
+ else
+ ep0buff = 0;
+ break;
+
+ default:
+ break;
+ }
+
+ /* Return data */
+ udc_write_hwep(udc, EP_IN, &ep0buff, 2);
+
+ return 0;
+}
+
+static void udc_handle_ep0_setup(struct lpc32xx_udc *udc)
+{
+ struct lpc32xx_ep *ep, *ep0 = &udc->ep[0];
+ struct usb_ctrlrequest ctrlpkt;
+ int i, bytes;
+ u16 wIndex, wValue, wLength, reqtype, req, tmp;
+
+ /* Nuke previous transfers */
+ nuke(ep0, -EPROTO);
+
+ /* Get setup packet */
+ bytes = udc_read_hwep(udc, EP_OUT, (u32 *) &ctrlpkt, 8);
+ if (bytes != 8) {
+ ep_warn(ep0, "Incorrectly sized setup packet (s/b 8, is %d)!\n",
+ bytes);
+ return;
+ }
+
+ /* Native endianness */
+ wIndex = le16_to_cpu(ctrlpkt.wIndex);
+ wValue = le16_to_cpu(ctrlpkt.wValue);
+ wLength = le16_to_cpu(ctrlpkt.wLength);
+ reqtype = le16_to_cpu(ctrlpkt.bRequestType);
+
+ /* Set direction of EP0 */
+ if (likely(reqtype & USB_DIR_IN))
+ ep0->is_in = 1;
+ else
+ ep0->is_in = 0;
+
+ /* Handle SETUP packet */
+ req = le16_to_cpu(ctrlpkt.bRequest);
+ switch (req) {
+ case USB_REQ_CLEAR_FEATURE:
+ case USB_REQ_SET_FEATURE:
+ switch (reqtype) {
+ case (USB_TYPE_STANDARD | USB_RECIP_DEVICE):
+ if (wValue != USB_DEVICE_REMOTE_WAKEUP)
+ goto stall; /* Nothing else handled */
+
+ /* Tell board about event */
+ if (req == USB_REQ_CLEAR_FEATURE)
+ udc->dev_status &=
+ ~(1 << USB_DEVICE_REMOTE_WAKEUP);
+ else
+ udc->dev_status |=
+ (1 << USB_DEVICE_REMOTE_WAKEUP);
+ uda_remwkp_cgh(udc);
+ goto zlp_send;
+
+ case (USB_TYPE_STANDARD | USB_RECIP_ENDPOINT):
+ tmp = wIndex & USB_ENDPOINT_NUMBER_MASK;
+ if ((wValue != USB_ENDPOINT_HALT) ||
+ (tmp >= NUM_ENDPOINTS))
+ break;
+
+ /* Find hardware endpoint from logical endpoint */
+ ep = &udc->ep[tmp];
+ tmp = ep->hwep_num;
+ if (tmp == 0)
+ break;
+
+ if (req == USB_REQ_SET_FEATURE)
+ udc_stall_hwep(udc, tmp);
+ else if (!ep->wedge)
+ udc_clrstall_hwep(udc, tmp);
+
+ goto zlp_send;
+
+ default:
+ break;
+ }
+
+
+ case USB_REQ_SET_ADDRESS:
+ if (reqtype == (USB_TYPE_STANDARD | USB_RECIP_DEVICE)) {
+ udc_set_address(udc, wValue);
+ goto zlp_send;
+ }
+ break;
+
+ case USB_REQ_GET_STATUS:
+ udc_get_status(udc, reqtype, wIndex);
+ return;
+
+ default:
+ break; /* Let GadgetFS handle the descriptor instead */
+ }
+
+ if (likely(udc->driver)) {
+ /* device-2-host (IN) or no data setup command, process
+ * immediately */
+ spin_unlock(&udc->lock);
+ i = udc->driver->setup(&udc->gadget, &ctrlpkt);
+
+ spin_lock(&udc->lock);
+ if (req == USB_REQ_SET_CONFIGURATION) {
+ /* Configuration is set after endpoints are realized */
+ if (wValue) {
+ /* Set configuration */
+ udc_set_device_configured(udc);
+
+ udc_protocol_cmd_data_w(udc, CMD_SET_MODE,
+ DAT_WR_BYTE(AP_CLK |
+ INAK_BI | INAK_II));
+ } else {
+ /* Clear configuration */
+ udc_set_device_unconfigured(udc);
+
+ /* Disable NAK interrupts */
+ udc_protocol_cmd_data_w(udc, CMD_SET_MODE,
+ DAT_WR_BYTE(AP_CLK));
+ }
+ }
+
+ if (i < 0) {
+ /* setup processing failed, force stall */
+ dev_err(udc->dev,
+ "req %02x.%02x protocol STALL; stat %d\n",
+ reqtype, req, i);
+ udc->ep0state = WAIT_FOR_SETUP;
+ goto stall;
+ }
+ }
+
+ if (!ep0->is_in)
+ udc_ep0_send_zlp(udc); /* ZLP IN packet on data phase */
+
+ return;
+
+stall:
+ udc_stall_hwep(udc, EP_IN);
+ return;
+
+zlp_send:
+ udc_ep0_send_zlp(udc);
+ return;
+}
+
+/* IN endpoint 0 transfer */
+static void udc_handle_ep0_in(struct lpc32xx_udc *udc)
+{
+ struct lpc32xx_ep *ep0 = &udc->ep[0];
+ u32 epstatus;
+
+ /* Clear EP interrupt */
+ epstatus = udc_clearep_getsts(udc, EP_IN);
+
+#ifdef CONFIG_USB_GADGET_DEBUG_FILES
+ ep0->totalints++;
+#endif
+
+ /* Stalled? Clear stall and reset buffers */
+ if (epstatus & EP_SEL_ST) {
+ udc_clrstall_hwep(udc, EP_IN);
+ nuke(ep0, -ECONNABORTED);
+ udc->ep0state = WAIT_FOR_SETUP;
+ return;
+ }
+
+ /* Is a buffer available? */
+ if (!(epstatus & EP_SEL_F)) {
+ /* Handle based on current state */
+ if (udc->ep0state == DATA_IN)
+ udc_ep0_in_req(udc);
+ else {
+ /* Unknown state for EP0 oe end of DATA IN phase */
+ nuke(ep0, -ECONNABORTED);
+ udc->ep0state = WAIT_FOR_SETUP;
+ }
+ }
+}
+
+/* OUT endpoint 0 transfer */
+static void udc_handle_ep0_out(struct lpc32xx_udc *udc)
+{
+ struct lpc32xx_ep *ep0 = &udc->ep[0];
+ u32 epstatus;
+
+ /* Clear EP interrupt */
+ epstatus = udc_clearep_getsts(udc, EP_OUT);
+
+
+#ifdef CONFIG_USB_GADGET_DEBUG_FILES
+ ep0->totalints++;
+#endif
+
+ /* Stalled? */
+ if (epstatus & EP_SEL_ST) {
+ udc_clrstall_hwep(udc, EP_OUT);
+ nuke(ep0, -ECONNABORTED);
+ udc->ep0state = WAIT_FOR_SETUP;
+ return;
+ }
+
+ /* A NAK may occur if a packet couldn't be received yet */
+ if (epstatus & EP_SEL_EPN)
+ return;
+ /* Setup packet incoming? */
+ if (epstatus & EP_SEL_STP) {
+ nuke(ep0, 0);
+ udc->ep0state = WAIT_FOR_SETUP;
+ }
+
+ /* Data available? */
+ if (epstatus & EP_SEL_F)
+ /* Handle based on current state */
+ switch (udc->ep0state) {
+ case WAIT_FOR_SETUP:
+ udc_handle_ep0_setup(udc);
+ break;
+
+ case DATA_OUT:
+ udc_ep0_out_req(udc);
+ break;
+
+ default:
+ /* Unknown state for EP0 */
+ nuke(ep0, -ECONNABORTED);
+ udc->ep0state = WAIT_FOR_SETUP;
+ }
+}
+
+/* Must be called without lock */
+static int lpc32xx_get_frame(struct usb_gadget *gadget)
+{
+ int frame;
+ unsigned long flags;
+ struct lpc32xx_udc *udc = to_udc(gadget);
+
+ if (!udc->clocked)
+ return -EINVAL;
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ frame = (int) udc_get_current_frame(udc);
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ return frame;
+}
+
+static int lpc32xx_wakeup(struct usb_gadget *gadget)
+{
+ return -ENOTSUPP;
+}
+
+static int lpc32xx_set_selfpowered(struct usb_gadget *gadget, int is_on)
+{
+ struct lpc32xx_udc *udc = to_udc(gadget);
+
+ /* Always self-powered */
+ udc->selfpowered = (is_on != 0);
+
+ return 0;
+}
+
+/*
+ * vbus is here! turn everything on that's ready
+ * Must be called without lock
+ */
+static int lpc32xx_vbus_session(struct usb_gadget *gadget, int is_active)
+{
+ unsigned long flags;
+ struct lpc32xx_udc *udc = to_udc(gadget);
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ /* Doesn't need lock */
+ if (udc->driver) {
+ udc_clk_set(udc, 1);
+ udc_enable(udc);
+ pullup(udc, is_active);
+ } else {
+ stop_activity(udc);
+ pullup(udc, 0);
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+ /*
+ * Wait for all the endpoints to disable,
+ * before disabling clocks. Don't wait if
+ * endpoints are not enabled.
+ */
+ if (atomic_read(&udc->enabled_ep_cnt))
+ wait_event_interruptible(udc->ep_disable_wait_queue,
+ (atomic_read(&udc->enabled_ep_cnt) == 0));
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ udc_clk_set(udc, 0);
+ }
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ return 0;
+}
+
+/* Can be called with or without lock */
+static int lpc32xx_pullup(struct usb_gadget *gadget, int is_on)
+{
+ struct lpc32xx_udc *udc = to_udc(gadget);
+
+ /* Doesn't need lock */
+ pullup(udc, is_on);
+
+ return 0;
+}
+
+static int lpc32xx_start(struct usb_gadget_driver *driver,
+ int (*bind)(struct usb_gadget *));
+static int lpc32xx_stop(struct usb_gadget_driver *driver);
+
+static const struct usb_gadget_ops lpc32xx_udc_ops = {
+ .get_frame = lpc32xx_get_frame,
+ .wakeup = lpc32xx_wakeup,
+ .set_selfpowered = lpc32xx_set_selfpowered,
+ .vbus_session = lpc32xx_vbus_session,
+ .pullup = lpc32xx_pullup,
+ .start = lpc32xx_start,
+ .stop = lpc32xx_stop,
+};
+
+static void nop_release(struct device *dev)
+{
+ /* nothing to free */
+}
+
+static struct lpc32xx_udc controller = {
+ .gadget = {
+ .ops = &lpc32xx_udc_ops,
+ .ep0 = &controller.ep[0].ep,
+ .name = driver_name,
+ .dev = {
+ .init_name = "gadget",
+ .release = nop_release,
+ }
+ },
+ .ep[0] = {
+ .ep = {
+ .name = "ep0",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 64,
+ .hwep_num_base = 0,
+ .hwep_num = 0, /* Can be 0 or 1, has special handling */
+ .lep = 0,
+ .eptype = EP_CTL_TYPE,
+ },
+ .ep[1] = {
+ .ep = {
+ .name = "ep1-int",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 64,
+ .hwep_num_base = 2,
+ .hwep_num = 0, /* 2 or 3, will be set later */
+ .lep = 1,
+ .eptype = EP_INT_TYPE,
+ },
+ .ep[2] = {
+ .ep = {
+ .name = "ep2-bulk",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 64,
+ .hwep_num_base = 4,
+ .hwep_num = 0, /* 4 or 5, will be set later */
+ .lep = 2,
+ .eptype = EP_BLK_TYPE,
+ },
+ .ep[3] = {
+ .ep = {
+ .name = "ep3-iso",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 1023,
+ .hwep_num_base = 6,
+ .hwep_num = 0, /* 6 or 7, will be set later */
+ .lep = 3,
+ .eptype = EP_ISO_TYPE,
+ },
+ .ep[4] = {
+ .ep = {
+ .name = "ep4-int",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 64,
+ .hwep_num_base = 8,
+ .hwep_num = 0, /* 8 or 9, will be set later */
+ .lep = 4,
+ .eptype = EP_INT_TYPE,
+ },
+ .ep[5] = {
+ .ep = {
+ .name = "ep5-bulk",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 64,
+ .hwep_num_base = 10,
+ .hwep_num = 0, /* 10 or 11, will be set later */
+ .lep = 5,
+ .eptype = EP_BLK_TYPE,
+ },
+ .ep[6] = {
+ .ep = {
+ .name = "ep6-iso",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 1023,
+ .hwep_num_base = 12,
+ .hwep_num = 0, /* 12 or 13, will be set later */
+ .lep = 6,
+ .eptype = EP_ISO_TYPE,
+ },
+ .ep[7] = {
+ .ep = {
+ .name = "ep7-int",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 64,
+ .hwep_num_base = 14,
+ .hwep_num = 0,
+ .lep = 7,
+ .eptype = EP_INT_TYPE,
+ },
+ .ep[8] = {
+ .ep = {
+ .name = "ep8-bulk",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 64,
+ .hwep_num_base = 16,
+ .hwep_num = 0,
+ .lep = 8,
+ .eptype = EP_BLK_TYPE,
+ },
+ .ep[9] = {
+ .ep = {
+ .name = "ep9-iso",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 1023,
+ .hwep_num_base = 18,
+ .hwep_num = 0,
+ .lep = 9,
+ .eptype = EP_ISO_TYPE,
+ },
+ .ep[10] = {
+ .ep = {
+ .name = "ep10-int",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 64,
+ .hwep_num_base = 20,
+ .hwep_num = 0,
+ .lep = 10,
+ .eptype = EP_INT_TYPE,
+ },
+ .ep[11] = {
+ .ep = {
+ .name = "ep11-bulk",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 64,
+ .hwep_num_base = 22,
+ .hwep_num = 0,
+ .lep = 11,
+ .eptype = EP_BLK_TYPE,
+ },
+ .ep[12] = {
+ .ep = {
+ .name = "ep12-iso",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 1023,
+ .hwep_num_base = 24,
+ .hwep_num = 0,
+ .lep = 12,
+ .eptype = EP_ISO_TYPE,
+ },
+ .ep[13] = {
+ .ep = {
+ .name = "ep13-int",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 64,
+ .hwep_num_base = 26,
+ .hwep_num = 0,
+ .lep = 13,
+ .eptype = EP_INT_TYPE,
+ },
+ .ep[14] = {
+ .ep = {
+ .name = "ep14-bulk",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 64,
+ .hwep_num_base = 28,
+ .hwep_num = 0,
+ .lep = 14,
+ .eptype = EP_BLK_TYPE,
+ },
+ .ep[15] = {
+ .ep = {
+ .name = "ep15-bulk",
+ .ops = &lpc32xx_ep_ops,
+ },
+ .udc = &controller,
+ .maxpacket = 1023,
+ .hwep_num_base = 30,
+ .hwep_num = 0,
+ .lep = 15,
+ .eptype = EP_BLK_TYPE,
+ },
+};
+
+/* ISO and status interrupts */
+static irqreturn_t lpc32xx_usb_lp_irq(int irq, void *_udc)
+{
+ u32 tmp, devstat;
+ struct lpc32xx_udc *udc = _udc;
+
+ spin_lock(&udc->lock);
+
+ /* Read the device status register */
+ devstat = readl(USBD_DEVINTST(udc->udp_baseaddr));
+
+ devstat &= ~USBD_EP_FAST;
+ writel(devstat, USBD_DEVINTCLR(udc->udp_baseaddr));
+ devstat = devstat & udc->enabled_devints;
+
+ /* Device specific handling needed? */
+ if (devstat & USBD_DEV_STAT)
+ udc_handle_dev(udc);
+
+ /* Start of frame? (devstat & FRAME_INT):
+ * The frame interrupt isn't really needed for ISO support,
+ * as the driver will queue the necessary packets */
+
+ /* Error? */
+ if (devstat & ERR_INT) {
+ /* All types of errors, from cable removal during transfer to
+ * misc protocol and bit errors. These are mostly for just info,
+ * as the USB hardware will work around these. If these errors
+ * happen alot, something is wrong. */
+ udc_protocol_cmd_w(udc, CMD_RD_ERR_STAT);
+ tmp = udc_protocol_cmd_r(udc, DAT_RD_ERR_STAT);
+ dev_dbg(udc->dev, "Device error (0x%x)!\n", tmp);
+ }
+
+ spin_unlock(&udc->lock);
+
+ return IRQ_HANDLED;
+}
+
+/* EP interrupts */
+static irqreturn_t lpc32xx_usb_hp_irq(int irq, void *_udc)
+{
+ u32 tmp;
+ struct lpc32xx_udc *udc = _udc;
+
+ spin_lock(&udc->lock);
+
+ /* Read the device status register */
+ writel(USBD_EP_FAST, USBD_DEVINTCLR(udc->udp_baseaddr));
+
+ /* Endpoints */
+ tmp = readl(USBD_EPINTST(udc->udp_baseaddr));
+
+ /* Special handling for EP0 */
+ if (tmp & (EP_MASK_SEL(0, EP_OUT) | EP_MASK_SEL(0, EP_IN))) {
+ /* Handle EP0 IN */
+ if (tmp & (EP_MASK_SEL(0, EP_IN)))
+ udc_handle_ep0_in(udc);
+
+ /* Handle EP0 OUT */
+ if (tmp & (EP_MASK_SEL(0, EP_OUT)))
+ udc_handle_ep0_out(udc);
+ }
+
+ /* All other EPs */
+ if (tmp & ~(EP_MASK_SEL(0, EP_OUT) | EP_MASK_SEL(0, EP_IN))) {
+ int i;
+
+ /* Handle other EP interrupts */
+ for (i = 1; i < NUM_ENDPOINTS; i++) {
+ if (tmp & (1 << udc->ep[i].hwep_num))
+ udc_handle_eps(udc, &udc->ep[i]);
+ }
+ }
+
+ spin_unlock(&udc->lock);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t lpc32xx_usb_devdma_irq(int irq, void *_udc)
+{
+ struct lpc32xx_udc *udc = _udc;
+
+ int i;
+ u32 tmp;
+
+ spin_lock(&udc->lock);
+
+ /* Handle EP DMA EOT interrupts */
+ tmp = readl(USBD_EOTINTST(udc->udp_baseaddr)) |
+ (readl(USBD_EPDMAST(udc->udp_baseaddr)) &
+ readl(USBD_NDDRTINTST(udc->udp_baseaddr))) |
+ readl(USBD_SYSERRTINTST(udc->udp_baseaddr));
+ for (i = 1; i < NUM_ENDPOINTS; i++) {
+ if (tmp & (1 << udc->ep[i].hwep_num))
+ udc_handle_dma_ep(udc, &udc->ep[i]);
+ }
+
+ spin_unlock(&udc->lock);
+
+ return IRQ_HANDLED;
+}
+
+/*
+ *
+ * VBUS detection, pullup handler, and Gadget cable state notification
+ *
+ */
+static void vbus_work(struct work_struct *work)
+{
+ u8 value;
+ struct lpc32xx_udc *udc = container_of(work, struct lpc32xx_udc,
+ vbus_job);
+
+ if (udc->enabled != 0) {
+ /* Discharge VBUS real quick */
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_OTG_CONTROL_1, OTG1_VBUS_DISCHRG);
+
+ /* Give VBUS some time (100mS) to discharge */
+ msleep(100);
+
+ /* Disable VBUS discharge resistor */
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR,
+ OTG1_VBUS_DISCHRG);
+
+ /* Clear interrupt */
+ i2c_smbus_write_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_INTERRUPT_LATCH |
+ ISP1301_I2C_REG_CLEAR_ADDR, ~0);
+
+ /* Get the VBUS status from the transceiver */
+ value = i2c_smbus_read_byte_data(udc->isp1301_i2c_client,
+ ISP1301_I2C_OTG_CONTROL_2);
+
+ /* VBUS on or off? */
+ if (value & OTG_B_SESS_VLD)
+ udc->vbus = 1;
+ else
+ udc->vbus = 0;
+
+ /* VBUS changed? */
+ if (udc->last_vbus != udc->vbus) {
+ udc->last_vbus = udc->vbus;
+ lpc32xx_vbus_session(&udc->gadget, udc->vbus);
+ }
+ }
+
+ /* Re-enable after completion */
+ enable_irq(udc->udp_irq[IRQ_USB_ATX]);
+}
+
+static irqreturn_t lpc32xx_usb_vbus_irq(int irq, void *_udc)
+{
+ struct lpc32xx_udc *udc = _udc;
+
+ /* Defer handling of VBUS IRQ to work queue */
+ disable_irq_nosync(udc->udp_irq[IRQ_USB_ATX]);
+ schedule_work(&udc->vbus_job);
+
+ return IRQ_HANDLED;
+}
+
+static int lpc32xx_start(struct usb_gadget_driver *driver,
+ int (*bind)(struct usb_gadget *))
+{
+ struct lpc32xx_udc *udc = &controller;
+ int retval, i;
+
+ if (!driver || driver->max_speed < USB_SPEED_FULL ||
+ !bind || !driver->setup) {
+ dev_err(udc->dev, "bad parameter.\n");
+ return -EINVAL;
+ }
+
+ if (udc->driver) {
+ dev_err(udc->dev, "UDC already has a gadget driver\n");
+ return -EBUSY;
+ }
+
+ udc->driver = driver;
+ udc->gadget.dev.driver = &driver->driver;
+ udc->enabled = 1;
+ udc->selfpowered = 1;
+ udc->vbus = 0;
+
+ retval = bind(&udc->gadget);
+ if (retval) {
+ dev_err(udc->dev, "bind() returned %d\n", retval);
+ udc->enabled = 0;
+ udc->selfpowered = 0;
+ udc->driver = NULL;
+ udc->gadget.dev.driver = NULL;
+ return retval;
+ }
+
+ dev_dbg(udc->dev, "bound to %s\n", driver->driver.name);
+
+ /* Force VBUS process once to check for cable insertion */
+ udc->last_vbus = udc->vbus = 0;
+ schedule_work(&udc->vbus_job);
+
+ /* Do not re-enable ATX IRQ (3) */
+ for (i = IRQ_USB_LP; i < IRQ_USB_ATX; i++)
+ enable_irq(udc->udp_irq[i]);
+
+ return 0;
+}
+
+static int lpc32xx_stop(struct usb_gadget_driver *driver)
+{
+ int i;
+ struct lpc32xx_udc *udc = &controller;
+
+ if (!driver || driver != udc->driver || !driver->unbind)
+ return -EINVAL;
+
+ /* Disable USB pullup */
+ isp1301_pullup_enable(udc, 0, 1);
+
+ for (i = IRQ_USB_LP; i <= IRQ_USB_ATX; i++)
+ disable_irq(udc->udp_irq[i]);
+
+ if (udc->clocked) {
+
+ spin_lock(&udc->lock);
+ stop_activity(udc);
+ spin_unlock(&udc->lock);
+
+ /*
+ * Wait for all the endpoints to disable,
+ * before disabling clocks. Don't wait if
+ * endpoints are not enabled.
+ */
+ if (atomic_read(&udc->enabled_ep_cnt))
+ wait_event_interruptible(udc->ep_disable_wait_queue,
+ (atomic_read(&udc->enabled_ep_cnt) == 0));
+
+ spin_lock(&udc->lock);
+ udc_clk_set(udc, 0);
+ spin_unlock(&udc->lock);
+ }
+
+ udc->enabled = 0;
+ pullup(udc, 0);
+
+ driver->unbind(&udc->gadget);
+ udc->gadget.dev.driver = NULL;
+ udc->driver = NULL;
+
+ dev_dbg(udc->dev, "unbound from %s\n", driver->driver.name);
+ return 0;
+}
+
+static void lpc32xx_udc_shutdown(struct platform_device *dev)
+{
+ /* Force disconnect on reboot */
+ struct lpc32xx_udc *udc = &controller;
+
+ pullup(udc, 0);
+}
+
+/*
+ * Callbacks to be overridden by options passed via OF (TODO)
+ */
+
+static void lpc32xx_usbd_conn_chg(int conn)
+{
+ /* Do nothing, it might be nice to enable an LED
+ * based on conn state being !0 */
+}
+
+static void lpc32xx_usbd_susp_chg(int susp)
+{
+ /* Device suspend if susp != 0 */
+}
+
+static void lpc32xx_rmwkup_chg(int remote_wakup_enable)
+{
+ /* Enable or disable USB remote wakeup */
+}
+
+struct lpc32xx_usbd_cfg lpc32xx_usbddata = {
+ .vbus_drv_pol = 0,
+ .conn_chgb = &lpc32xx_usbd_conn_chg,
+ .susp_chgb = &lpc32xx_usbd_susp_chg,
+ .rmwk_chgb = &lpc32xx_rmwkup_chg,
+};
+
+
+static u64 lpc32xx_usbd_dmamask = ~(u32) 0x7F;
+
+static int __init lpc32xx_udc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct lpc32xx_udc *udc = &controller;
+ int retval, i;
+ struct resource *res;
+ dma_addr_t dma_handle;
+ struct device_node *isp1301_node;
+
+ /* init software state */
+ udc->gadget.dev.parent = dev;
+ udc->pdev = pdev;
+ udc->dev = &pdev->dev;
+ udc->enabled = 0;
+
+ if (pdev->dev.of_node) {
+ isp1301_node = of_parse_phandle(pdev->dev.of_node,
+ "transceiver", 0);
+ } else {
+ isp1301_node = NULL;
+ }
+
+ udc->isp1301_i2c_client = isp1301_get_client(isp1301_node);
+ if (!udc->isp1301_i2c_client)
+ return -EPROBE_DEFER;
+
+ dev_info(udc->dev, "ISP1301 I2C device at address 0x%x\n",
+ udc->isp1301_i2c_client->addr);
+
+ pdev->dev.dma_mask = &lpc32xx_usbd_dmamask;
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
+
+ udc->board = &lpc32xx_usbddata;
+
+ /*
+ * Resources are mapped as follows:
+ * IORESOURCE_MEM, base address and size of USB space
+ * IORESOURCE_IRQ, USB device low priority interrupt number
+ * IORESOURCE_IRQ, USB device high priority interrupt number
+ * IORESOURCE_IRQ, USB device interrupt number
+ * IORESOURCE_IRQ, USB transceiver interrupt number
+ */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res)
+ return -ENXIO;
+
+ spin_lock_init(&udc->lock);
+
+ /* Get IRQs */
+ for (i = 0; i < 4; i++) {
+ udc->udp_irq[i] = platform_get_irq(pdev, i);
+ if (udc->udp_irq[i] < 0) {
+ dev_err(udc->dev,
+ "irq resource %d not available!\n", i);
+ return udc->udp_irq[i];
+ }
+ }
+
+ udc->io_p_start = res->start;
+ udc->io_p_size = resource_size(res);
+ if (!request_mem_region(udc->io_p_start, udc->io_p_size, driver_name)) {
+ dev_err(udc->dev, "someone's using UDC memory\n");
+ return -EBUSY;
+ }
+
+ udc->udp_baseaddr = ioremap(udc->io_p_start, udc->io_p_size);
+ if (!udc->udp_baseaddr) {
+ retval = -ENOMEM;
+ dev_err(udc->dev, "IO map failure\n");
+ goto io_map_fail;
+ }
+
+ /* Enable AHB slave USB clock, needed for further USB clock control */
+ writel(USB_SLAVE_HCLK_EN | (1 << 19), USB_CTRL);
+
+ /* Get required clocks */
+ udc->usb_pll_clk = clk_get(&pdev->dev, "ck_pll5");
+ if (IS_ERR(udc->usb_pll_clk)) {
+ dev_err(udc->dev, "failed to acquire USB PLL\n");
+ retval = PTR_ERR(udc->usb_pll_clk);
+ goto pll_get_fail;
+ }
+ udc->usb_slv_clk = clk_get(&pdev->dev, "ck_usbd");
+ if (IS_ERR(udc->usb_slv_clk)) {
+ dev_err(udc->dev, "failed to acquire USB device clock\n");
+ retval = PTR_ERR(udc->usb_slv_clk);
+ goto usb_clk_get_fail;
+ }
+
+ /* Setup PLL clock to 48MHz */
+ retval = clk_enable(udc->usb_pll_clk);
+ if (retval < 0) {
+ dev_err(udc->dev, "failed to start USB PLL\n");
+ goto pll_enable_fail;
+ }
+
+ retval = clk_set_rate(udc->usb_pll_clk, 48000);
+ if (retval < 0) {
+ dev_err(udc->dev, "failed to set USB clock rate\n");
+ goto pll_set_fail;
+ }
+
+ writel(readl(USB_CTRL) | USB_DEV_NEED_CLK_EN, USB_CTRL);
+
+ /* Enable USB device clock */
+ retval = clk_enable(udc->usb_slv_clk);
+ if (retval < 0) {
+ dev_err(udc->dev, "failed to start USB device clock\n");
+ goto usb_clk_enable_fail;
+ }
+
+ /* Set to enable all needed USB OTG clocks */
+ writel(USB_CLOCK_MASK, USB_OTG_CLK_CTRL(udc));
+
+ i = 1000;
+ while (((readl(USB_OTG_CLK_STAT(udc)) & USB_CLOCK_MASK) !=
+ USB_CLOCK_MASK) && (i > 0))
+ i--;
+ if (!i)
+ dev_dbg(udc->dev, "USB OTG clocks not correctly enabled\n");
+
+ /* Setup deferred workqueue data */
+ udc->poweron = udc->pullup = 0;
+ INIT_WORK(&udc->pullup_job, pullup_work);
+ INIT_WORK(&udc->vbus_job, vbus_work);
+#ifdef CONFIG_PM
+ INIT_WORK(&udc->power_job, power_work);
+#endif
+
+ /* All clocks are now on */
+ udc->clocked = 1;
+
+ isp1301_udc_configure(udc);
+ /* Allocate memory for the UDCA */
+ udc->udca_v_base = dma_alloc_coherent(&pdev->dev, UDCA_BUFF_SIZE,
+ &dma_handle,
+ (GFP_KERNEL | GFP_DMA));
+ if (!udc->udca_v_base) {
+ dev_err(udc->dev, "error getting UDCA region\n");
+ retval = -ENOMEM;
+ goto i2c_fail;
+ }
+ udc->udca_p_base = dma_handle;
+ dev_dbg(udc->dev, "DMA buffer(0x%x bytes), P:0x%08x, V:0x%p\n",
+ UDCA_BUFF_SIZE, udc->udca_p_base, udc->udca_v_base);
+
+ /* Setup the DD DMA memory pool */
+ udc->dd_cache = dma_pool_create("udc_dd", udc->dev,
+ sizeof(struct lpc32xx_usbd_dd_gad),
+ sizeof(u32), 0);
+ if (!udc->dd_cache) {
+ dev_err(udc->dev, "error getting DD DMA region\n");
+ retval = -ENOMEM;
+ goto dma_alloc_fail;
+ }
+
+ /* Clear USB peripheral and initialize gadget endpoints */
+ udc_disable(udc);
+ udc_reinit(udc);
+
+ retval = device_register(&udc->gadget.dev);
+ if (retval < 0) {
+ dev_err(udc->dev, "Device registration failure\n");
+ goto dev_register_fail;
+ }
+
+ /* Request IRQs - low and high priority USB device IRQs are routed to
+ * the same handler, while the DMA interrupt is routed elsewhere */
+ retval = request_irq(udc->udp_irq[IRQ_USB_LP], lpc32xx_usb_lp_irq,
+ 0, "udc_lp", udc);
+ if (retval < 0) {
+ dev_err(udc->dev, "LP request irq %d failed\n",
+ udc->udp_irq[IRQ_USB_LP]);
+ goto irq_lp_fail;
+ }
+ retval = request_irq(udc->udp_irq[IRQ_USB_HP], lpc32xx_usb_hp_irq,
+ 0, "udc_hp", udc);
+ if (retval < 0) {
+ dev_err(udc->dev, "HP request irq %d failed\n",
+ udc->udp_irq[IRQ_USB_HP]);
+ goto irq_hp_fail;
+ }
+
+ retval = request_irq(udc->udp_irq[IRQ_USB_DEVDMA],
+ lpc32xx_usb_devdma_irq, 0, "udc_dma", udc);
+ if (retval < 0) {
+ dev_err(udc->dev, "DEV request irq %d failed\n",
+ udc->udp_irq[IRQ_USB_DEVDMA]);
+ goto irq_dev_fail;
+ }
+
+ /* The transceiver interrupt is used for VBUS detection and will
+ kick off the VBUS handler function */
+ retval = request_irq(udc->udp_irq[IRQ_USB_ATX], lpc32xx_usb_vbus_irq,
+ 0, "udc_otg", udc);
+ if (retval < 0) {
+ dev_err(udc->dev, "VBUS request irq %d failed\n",
+ udc->udp_irq[IRQ_USB_ATX]);
+ goto irq_xcvr_fail;
+ }
+
+ /* Initialize wait queue */
+ init_waitqueue_head(&udc->ep_disable_wait_queue);
+ atomic_set(&udc->enabled_ep_cnt, 0);
+
+ /* Keep all IRQs disabled until GadgetFS starts up */
+ for (i = IRQ_USB_LP; i <= IRQ_USB_ATX; i++)
+ disable_irq(udc->udp_irq[i]);
+
+ retval = usb_add_gadget_udc(dev, &udc->gadget);
+ if (retval < 0)
+ goto add_gadget_fail;
+
+ dev_set_drvdata(dev, udc);
+ device_init_wakeup(dev, 1);
+ create_debug_file(udc);
+
+ /* Disable clocks for now */
+ udc_clk_set(udc, 0);
+
+ dev_info(udc->dev, "%s version %s\n", driver_name, DRIVER_VERSION);
+ return 0;
+
+add_gadget_fail:
+ free_irq(udc->udp_irq[IRQ_USB_ATX], udc);
+irq_xcvr_fail:
+ free_irq(udc->udp_irq[IRQ_USB_DEVDMA], udc);
+irq_dev_fail:
+ free_irq(udc->udp_irq[IRQ_USB_HP], udc);
+irq_hp_fail:
+ free_irq(udc->udp_irq[IRQ_USB_LP], udc);
+irq_lp_fail:
+ device_unregister(&udc->gadget.dev);
+dev_register_fail:
+ dma_pool_destroy(udc->dd_cache);
+dma_alloc_fail:
+ dma_free_coherent(&pdev->dev, UDCA_BUFF_SIZE,
+ udc->udca_v_base, udc->udca_p_base);
+i2c_fail:
+ clk_disable(udc->usb_slv_clk);
+usb_clk_enable_fail:
+pll_set_fail:
+ clk_disable(udc->usb_pll_clk);
+pll_enable_fail:
+ clk_put(udc->usb_slv_clk);
+usb_clk_get_fail:
+ clk_put(udc->usb_pll_clk);
+pll_get_fail:
+ iounmap(udc->udp_baseaddr);
+io_map_fail:
+ release_mem_region(udc->io_p_start, udc->io_p_size);
+ dev_err(udc->dev, "%s probe failed, %d\n", driver_name, retval);
+
+ return retval;
+}
+
+static int __devexit lpc32xx_udc_remove(struct platform_device *pdev)
+{
+ struct lpc32xx_udc *udc = platform_get_drvdata(pdev);
+
+ usb_del_gadget_udc(&udc->gadget);
+ if (udc->driver)
+ return -EBUSY;
+
+ udc_clk_set(udc, 1);
+ udc_disable(udc);
+ pullup(udc, 0);
+
+ free_irq(udc->udp_irq[IRQ_USB_ATX], udc);
+
+ device_init_wakeup(&pdev->dev, 0);
+ remove_debug_file(udc);
+
+ dma_pool_destroy(udc->dd_cache);
+ dma_free_coherent(&pdev->dev, UDCA_BUFF_SIZE,
+ udc->udca_v_base, udc->udca_p_base);
+ free_irq(udc->udp_irq[IRQ_USB_DEVDMA], udc);
+ free_irq(udc->udp_irq[IRQ_USB_HP], udc);
+ free_irq(udc->udp_irq[IRQ_USB_LP], udc);
+
+ device_unregister(&udc->gadget.dev);
+
+ clk_disable(udc->usb_slv_clk);
+ clk_put(udc->usb_slv_clk);
+ clk_disable(udc->usb_pll_clk);
+ clk_put(udc->usb_pll_clk);
+ iounmap(udc->udp_baseaddr);
+ release_mem_region(udc->io_p_start, udc->io_p_size);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int lpc32xx_udc_suspend(struct platform_device *pdev, pm_message_t mesg)
+{
+ int to = 1000;
+ struct lpc32xx_udc *udc = platform_get_drvdata(pdev);
+
+ if (udc->clocked) {
+ /* Power down ISP */
+ udc->poweron = 0;
+ isp1301_set_powerstate(udc, 0);
+
+ /* Disable clocking */
+ udc_clk_set(udc, 0);
+
+ /* Keep clock flag on, so we know to re-enable clocks
+ on resume */
+ udc->clocked = 1;
+
+ /* Kill OTG and I2C clocks */
+ writel(0, USB_OTG_CLK_CTRL(udc));
+ while (((readl(USB_OTG_CLK_STAT(udc)) & OTGOFF_CLK_MASK) !=
+ OTGOFF_CLK_MASK) && (to > 0))
+ to--;
+ if (!to)
+ dev_dbg(udc->dev,
+ "USB OTG clocks not correctly enabled\n");
+
+ /* Kill global USB clock */
+ clk_disable(udc->usb_slv_clk);
+ }
+
+ return 0;
+}
+
+static int lpc32xx_udc_resume(struct platform_device *pdev)
+{
+ struct lpc32xx_udc *udc = platform_get_drvdata(pdev);
+
+ if (udc->clocked) {
+ /* Enable global USB clock */
+ clk_enable(udc->usb_slv_clk);
+
+ /* Enable clocking */
+ udc_clk_set(udc, 1);
+
+ /* ISP back to normal power mode */
+ udc->poweron = 1;
+ isp1301_set_powerstate(udc, 1);
+ }
+
+ return 0;
+}
+#else
+#define lpc32xx_udc_suspend NULL
+#define lpc32xx_udc_resume NULL
+#endif
+
+#ifdef CONFIG_OF
+static struct of_device_id lpc32xx_udc_of_match[] = {
+ { .compatible = "nxp,lpc3220-udc", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, lpc32xx_udc_of_match);
+#endif
+
+static struct platform_driver lpc32xx_udc_driver = {
+ .remove = __devexit_p(lpc32xx_udc_remove),
+ .shutdown = lpc32xx_udc_shutdown,
+ .suspend = lpc32xx_udc_suspend,
+ .resume = lpc32xx_udc_resume,
+ .driver = {
+ .name = (char *) driver_name,
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(lpc32xx_udc_of_match),
+ },
+};
+
+static int __init udc_init_module(void)
+{
+ return platform_driver_probe(&lpc32xx_udc_driver, lpc32xx_udc_probe);
+}
+module_init(udc_init_module);
+
+static void __exit udc_exit_module(void)
+{
+ platform_driver_unregister(&lpc32xx_udc_driver);
+}
+module_exit(udc_exit_module);
+
+MODULE_DESCRIPTION("LPC32XX udc driver");
+MODULE_AUTHOR("Kevin Wells <kevin.wells@nxp.com>");
+MODULE_AUTHOR("Roland Stigge <stigge@antcom.de>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:lpc32xx_udc");
--
1.7.9
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v8 5/5] USB: ohci-nxp: Use isp1301 driver
2012-04-29 14:47 [PATCH v8 0/5] USB: LPC32xx device tree related OHCI and UDC patch series Roland Stigge
` (3 preceding siblings ...)
2012-04-29 14:47 ` [PATCH v8 4/5] USB: gadget driver for LPC32xx Roland Stigge
@ 2012-04-29 14:47 ` Roland Stigge
2012-05-01 17:37 ` [PATCH v8 0/5] USB: LPC32xx device tree related OHCI and UDC patch series Greg KH
5 siblings, 0 replies; 7+ messages in thread
From: Roland Stigge @ 2012-04-29 14:47 UTC (permalink / raw)
To: gregkh, linux-usb, linux-kernel, kevin.wells, srinivas.bakki,
stern, linux-arm-kernel, arnd, grant.likely, rob.herring,
devicetree-discuss
Cc: Roland Stigge
ohci-nxp duplicates the isp1301 driver. This patch removes this code and makes
ohci-nxp use the new separate isp1301 driver instead.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
Documentation/devicetree/bindings/usb/ohci-nxp.txt | 8 ++
drivers/usb/host/Kconfig | 1 +
drivers/usb/host/ohci-nxp.c | 121 +++-----------------
3 files changed, 24 insertions(+), 106 deletions(-)
diff --git a/Documentation/devicetree/bindings/usb/ohci-nxp.txt b/Documentation/devicetree/bindings/usb/ohci-nxp.txt
index b5c3631..71e28c1 100644
--- a/Documentation/devicetree/bindings/usb/ohci-nxp.txt
+++ b/Documentation/devicetree/bindings/usb/ohci-nxp.txt
@@ -5,12 +5,20 @@ Required properties:
- reg: physical base address of the controller and length of memory mapped
region.
- interrupts: The OHCI interrupt
+- transceiver: phandle of the associated ISP1301 device - this is necessary for
+ the UDC controller for connecting to the USB physical layer
Example (LPC32xx):
+ isp1301: usb-transceiver@2c {
+ compatible = "nxp,isp1301";
+ reg = <0x2c>;
+ };
+
ohci@31020000 {
compatible = "nxp,ohci-nxp";
reg = <0x31020000 0x300>;
interrupt-parent = <&mic>;
interrupts = <0x3b 0>;
+ transceiver = <&isp1301>;
};
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 896fc91..684a7bb 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -292,6 +292,7 @@ config USB_OHCI_HCD
depends on USB && USB_ARCH_HAS_OHCI
select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
select USB_OTG_UTILS if ARCH_OMAP
+ select USB_ISP1301 if ARCH_LPC32XX || ARCH_PNX4008
---help---
The Open Host Controller Interface (OHCI) is a standard for accessing
USB 1.1 host controller hardware. It does more in hardware than Intel's
diff --git a/drivers/usb/host/ohci-nxp.c b/drivers/usb/host/ohci-nxp.c
index bf542e7..1e364ec 100644
--- a/drivers/usb/host/ohci-nxp.c
+++ b/drivers/usb/host/ohci-nxp.c
@@ -23,6 +23,7 @@
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/of.h>
+#include <linux/usb/isp1301.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@@ -58,54 +59,6 @@
#define TRANSPARENT_I2C_EN (1 << 7)
#define HOST_EN (1 << 0)
-/* ISP1301 USB transceiver I2C registers */
-#define ISP1301_MODE_CONTROL_1 0x04 /* u8 read, set, +1 clear */
-
-#define MC1_SPEED_REG (1 << 0)
-#define MC1_SUSPEND_REG (1 << 1)
-#define MC1_DAT_SE0 (1 << 2)
-#define MC1_TRANSPARENT (1 << 3)
-#define MC1_BDIS_ACON_EN (1 << 4)
-#define MC1_OE_INT_EN (1 << 5)
-#define MC1_UART_EN (1 << 6)
-#define MC1_MASK 0x7f
-
-#define ISP1301_MODE_CONTROL_2 0x12 /* u8 read, set, +1 clear */
-
-#define MC2_GLOBAL_PWR_DN (1 << 0)
-#define MC2_SPD_SUSP_CTRL (1 << 1)
-#define MC2_BI_DI (1 << 2)
-#define MC2_TRANSP_BDIR0 (1 << 3)
-#define MC2_TRANSP_BDIR1 (1 << 4)
-#define MC2_AUDIO_EN (1 << 5)
-#define MC2_PSW_EN (1 << 6)
-#define MC2_EN2V7 (1 << 7)
-
-#define ISP1301_OTG_CONTROL_1 0x06 /* u8 read, set, +1 clear */
-# define OTG1_DP_PULLUP (1 << 0)
-# define OTG1_DM_PULLUP (1 << 1)
-# define OTG1_DP_PULLDOWN (1 << 2)
-# define OTG1_DM_PULLDOWN (1 << 3)
-# define OTG1_ID_PULLDOWN (1 << 4)
-# define OTG1_VBUS_DRV (1 << 5)
-# define OTG1_VBUS_DISCHRG (1 << 6)
-# define OTG1_VBUS_CHRG (1 << 7)
-#define ISP1301_OTG_STATUS 0x10 /* u8 readonly */
-# define OTG_B_SESS_END (1 << 6)
-# define OTG_B_SESS_VLD (1 << 7)
-
-#define ISP1301_I2C_ADDR 0x2C
-
-#define ISP1301_I2C_MODE_CONTROL_1 0x4
-#define ISP1301_I2C_MODE_CONTROL_2 0x12
-#define ISP1301_I2C_OTG_CONTROL_1 0x6
-#define ISP1301_I2C_OTG_CONTROL_2 0x10
-#define ISP1301_I2C_INTERRUPT_SOURCE 0x8
-#define ISP1301_I2C_INTERRUPT_LATCH 0xA
-#define ISP1301_I2C_INTERRUPT_FALLING 0xC
-#define ISP1301_I2C_INTERRUPT_RISING 0xE
-#define ISP1301_I2C_REG_CLEAR_ADDR 1
-
/* On LPC32xx, those are undefined */
#ifndef start_int_set_falling_edge
#define start_int_set_falling_edge(irq)
@@ -115,41 +68,12 @@
#define start_int_umask(irq)
#endif
-static struct i2c_driver isp1301_driver;
static struct i2c_client *isp1301_i2c_client;
extern int usb_disabled(void);
static struct clk *usb_clk;
-static const unsigned short normal_i2c[] =
- { ISP1301_I2C_ADDR, ISP1301_I2C_ADDR + 1, I2C_CLIENT_END };
-
-static int isp1301_probe(struct i2c_client *client,
- const struct i2c_device_id *id)
-{
- return 0;
-}
-
-static int isp1301_remove(struct i2c_client *client)
-{
- return 0;
-}
-
-static const struct i2c_device_id isp1301_id[] = {
- { "isp1301_nxp", 0 },
- { }
-};
-
-static struct i2c_driver isp1301_driver = {
- .driver = {
- .name = "isp1301_nxp",
- },
- .probe = isp1301_probe,
- .remove = isp1301_remove,
- .id_table = isp1301_id,
-};
-
static void isp1301_configure_pnx4008(void)
{
/* PNX4008 only supports DAT_SE0 USB mode */
@@ -373,11 +297,22 @@ static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev)
struct usb_hcd *hcd = 0;
struct ohci_hcd *ohci;
const struct hc_driver *driver = &ohci_nxp_hc_driver;
- struct i2c_adapter *i2c_adap;
- struct i2c_board_info i2c_info;
struct resource *res;
-
int ret = 0, irq;
+ struct device_node *isp1301_node;
+
+ if (pdev->dev.of_node) {
+ isp1301_node = of_parse_phandle(pdev->dev.of_node,
+ "transceiver", 0);
+ } else {
+ isp1301_node = NULL;
+ }
+
+ isp1301_i2c_client = isp1301_get_client(isp1301_node);
+ if (!isp1301_i2c_client) {
+ ret = -EPROBE_DEFER;
+ goto out;
+ }
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
@@ -392,28 +327,6 @@ static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev)
/* Enable AHB slave USB clock, needed for further USB clock control */
__raw_writel(USB_SLAVE_HCLK_EN | PAD_CONTROL_LAST_DRIVEN, USB_CTRL);
- ret = i2c_add_driver(&isp1301_driver);
- if (ret < 0) {
- dev_err(&pdev->dev, "failed to add ISP1301 driver\n");
- goto out;
- }
- i2c_adap = i2c_get_adapter(2);
- if (!i2c_adap) {
- dev_err(&pdev->dev, "failed on i2c_get_adapter");
- goto out_i2c_driver;
- }
-
- memset(&i2c_info, 0, sizeof(struct i2c_board_info));
- strlcpy(i2c_info.type, "isp1301_nxp", I2C_NAME_SIZE);
- isp1301_i2c_client = i2c_new_probed_device(i2c_adap, &i2c_info,
- normal_i2c, NULL);
- i2c_put_adapter(i2c_adap);
- if (!isp1301_i2c_client) {
- dev_err(&pdev->dev, "failed to connect I2C to ISP1301 USB Transceiver\n");
- ret = -ENODEV;
- goto out_i2c_driver;
- }
-
isp1301_configure();
/* Enable USB PLL */
@@ -495,10 +408,7 @@ out3:
out2:
clk_put(usb_clk);
out1:
- i2c_unregister_device(isp1301_i2c_client);
isp1301_i2c_client = NULL;
-out_i2c_driver:
- i2c_del_driver(&isp1301_driver);
out:
return ret;
}
@@ -516,7 +426,6 @@ static int usb_hcd_nxp_remove(struct platform_device *pdev)
clk_put(usb_clk);
i2c_unregister_device(isp1301_i2c_client);
isp1301_i2c_client = NULL;
- i2c_del_driver(&isp1301_driver);
platform_set_drvdata(pdev, NULL);
--
1.7.9
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v8 0/5] USB: LPC32xx device tree related OHCI and UDC patch series
2012-04-29 14:47 [PATCH v8 0/5] USB: LPC32xx device tree related OHCI and UDC patch series Roland Stigge
` (4 preceding siblings ...)
2012-04-29 14:47 ` [PATCH v8 5/5] USB: ohci-nxp: Use isp1301 driver Roland Stigge
@ 2012-05-01 17:37 ` Greg KH
5 siblings, 0 replies; 7+ messages in thread
From: Greg KH @ 2012-05-01 17:37 UTC (permalink / raw)
To: Roland Stigge
Cc: linux-usb, linux-kernel, kevin.wells, srinivas.bakki, stern,
linux-arm-kernel, arnd, grant.likely, rob.herring,
devicetree-discuss
On Sun, Apr 29, 2012 at 04:47:01PM +0200, Roland Stigge wrote:
> This series collects the pending LPC32xx patches in one series and forward
> ports it onto
>
> git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-next
>
> There are no other changes since last post.
All applied, thanks for your persistance.
greg k-h
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2012-05-01 17:37 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-04-29 14:47 [PATCH v8 0/5] USB: LPC32xx device tree related OHCI and UDC patch series Roland Stigge
2012-04-29 14:47 ` [PATCH v8 1/5] ohci-nxp: Driver cleanup Roland Stigge
2012-04-29 14:47 ` [PATCH v8 2/5] ohci-nxp: Device tree support Roland Stigge
2012-04-29 14:47 ` [PATCH v8 3/5] USB: Add driver for NXP ISP1301 USB transceiver Roland Stigge
2012-04-29 14:47 ` [PATCH v8 4/5] USB: gadget driver for LPC32xx Roland Stigge
2012-04-29 14:47 ` [PATCH v8 5/5] USB: ohci-nxp: Use isp1301 driver Roland Stigge
2012-05-01 17:37 ` [PATCH v8 0/5] USB: LPC32xx device tree related OHCI and UDC patch series Greg KH
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).