[PATCH RFC/RFT 1/7] regulator: core: Allow drivers to set voltage mapping table in regulator_desc

[PATCH RFC/RFT 1/7] regulator: core: Allow drivers to set voltage mapping table in regulator_desc

[Axel Lin]

Some regulator hardware use table based mapping can set volt_table in
regulator_desc and use regulator_list_voltage_table() for their list_voltage
callback.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
---
 drivers/regulator/core.c         |   25 +++++++++++++++++++++++++
 include/linux/regulator/driver.h |    5 +++++
 2 files changed, 30 insertions(+), 0 deletions(-)

diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index faa0532..0b15587 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -1880,6 +1880,31 @@ int regulator_list_voltage_linear(struct regulator_dev *rdev,
 EXPORT_SYMBOL_GPL(regulator_list_voltage_linear);
 
 /**
+ * regulator_list_voltage_table - List voltages with table based mapping
+ *
+ * @rdev: Regulator device
+ * @selector: Selector to convert into a voltage
+ *
+ * Regulators with table based mapping between voltages and
+ * selectors can set volt_table in the regulator descriptor
+ * and then use this function as their list_voltage() operation.
+ */
+int regulator_list_voltage_table(struct regulator_dev *rdev,
+				 unsigned int selector)
+{
+	if (!rdev->desc->volt_table) {
+		BUG_ON(!rdev->desc->volt_table);
+		return -EINVAL;
+	}
+
+	if (selector >= rdev->desc->n_voltages)
+		return -EINVAL;
+
+	return rdev->desc->volt_table[selector];
+}
+EXPORT_SYMBOL_GPL(regulator_list_voltage_table);
+
+/**
  * regulator_list_voltage - enumerate supported voltages
  * @regulator: regulator source
  * @selector: identify voltage to list
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index b0432cc..8022638 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -170,6 +170,7 @@ enum regulator_type {
  *
  * @min_uV: Voltage given by the lowest selector (if linear mapping)
  * @uV_step: Voltage increase with each selector (if linear mapping)
+ * @volt_table: Voltage mapping table (if table based mapping)
  *
  * @vsel_reg: Register for selector when using regulator_regmap_X_voltage_
  * @vsel_mask: Mask for register bitfield used for selector
@@ -189,6 +190,8 @@ struct regulator_desc {
 	unsigned int min_uV;
 	unsigned int uV_step;
 
+	const unsigned int *volt_table;
+
 	unsigned int vsel_reg;
 	unsigned int vsel_mask;
 	unsigned int enable_reg;
@@ -271,6 +274,8 @@ int regulator_mode_to_status(unsigned int);
 
 int regulator_list_voltage_linear(struct regulator_dev *rdev,
 				  unsigned int selector);
+int regulator_list_voltage_table(struct regulator_dev *rdev,
+				  unsigned int selector);
 int regulator_map_voltage_linear(struct regulator_dev *rdev,
 				  int min_uV, int max_uV);
 int regulator_map_voltage_iterate(struct regulator_dev *rdev,
-- 
1.7.5.4

[PATCH RFC/RFT 2/7] regulator: ab3100: Use regulator_list_voltage_table()

[Axel Lin]

Signed-off-by: Axel Lin <axel.lin@gmail.com>
---
 drivers/regulator/ab3100.c |   50 ++++++++++++-------------------------------
 1 files changed, 14 insertions(+), 36 deletions(-)

diff --git a/drivers/regulator/ab3100.c b/drivers/regulator/ab3100.c
index 03f4d9c..b088b6c 100644
--- a/drivers/regulator/ab3100.c
+++ b/drivers/regulator/ab3100.c
@@ -45,9 +45,6 @@
  * @regreg: regulator register number in the AB3100
  * @fixed_voltage: a fixed voltage for this regulator, if this
  *          0 the voltages array is used instead.
- * @typ_voltages: an array of available typical voltages for
- *          this regulator
- * @voltages_len: length of the array of available voltages
  */
 struct ab3100_regulator {
 	struct regulator_dev *rdev;
@@ -55,8 +52,6 @@ struct ab3100_regulator {
 	struct ab3100_platform_data *plfdata;
 	u8 regreg;
 	int fixed_voltage;
-	int const *typ_voltages;
-	u8 voltages_len;
 };
 
 /* The order in which registers are initialized */
@@ -80,7 +75,7 @@ static const u8 ab3100_reg_init_order[AB3100_NUM_REGULATORS+2] = {
 #define LDO_C_VOLTAGE 2650000
 #define LDO_D_VOLTAGE 2650000
 
-static const int ldo_e_buck_typ_voltages[] = {
+static const unsigned int ldo_e_buck_typ_voltages[] = {
 	1800000,
 	1400000,
 	1300000,
@@ -90,7 +85,7 @@ static const int ldo_e_buck_typ_voltages[] = {
 	900000,
 };
 
-static const int ldo_f_typ_voltages[] = {
+static const unsigned int ldo_f_typ_voltages[] = {
 	1800000,
 	1400000,
 	1300000,
@@ -101,21 +96,21 @@ static const int ldo_f_typ_voltages[] = {
 	2650000,
 };
 
-static const int ldo_g_typ_voltages[] = {
+static const unsigned int ldo_g_typ_voltages[] = {
 	2850000,
 	2750000,
 	1800000,
 	1500000,
 };
 
-static const int ldo_h_typ_voltages[] = {
+static const unsigned int ldo_h_typ_voltages[] = {
 	2750000,
 	1800000,
 	1500000,
 	1200000,
 };
 
-static const int ldo_k_typ_voltages[] = {
+static const unsigned int ldo_k_typ_voltages[] = {
 	2750000,
 	1800000,
 };
@@ -138,28 +133,18 @@ ab3100_regulators[AB3100_NUM_REGULATORS] = {
 	},
 	{
 		.regreg = AB3100_LDO_E,
-		.typ_voltages = ldo_e_buck_typ_voltages,
-		.voltages_len = ARRAY_SIZE(ldo_e_buck_typ_voltages),
 	},
 	{
 		.regreg = AB3100_LDO_F,
-		.typ_voltages = ldo_f_typ_voltages,
-		.voltages_len = ARRAY_SIZE(ldo_f_typ_voltages),
 	},
 	{
 		.regreg = AB3100_LDO_G,
-		.typ_voltages = ldo_g_typ_voltages,
-		.voltages_len = ARRAY_SIZE(ldo_g_typ_voltages),
 	},
 	{
 		.regreg = AB3100_LDO_H,
-		.typ_voltages = ldo_h_typ_voltages,
-		.voltages_len = ARRAY_SIZE(ldo_h_typ_voltages),
 	},
 	{
 		.regreg = AB3100_LDO_K,
-		.typ_voltages = ldo_k_typ_voltages,
-		.voltages_len = ARRAY_SIZE(ldo_k_typ_voltages),
 	},
 	{
 		.regreg = AB3100_LDO_EXT,
@@ -167,8 +152,6 @@ ab3100_regulators[AB3100_NUM_REGULATORS] = {
 	},
 	{
 		.regreg = AB3100_BUCK,
-		.typ_voltages = ldo_e_buck_typ_voltages,
-		.voltages_len = ARRAY_SIZE(ldo_e_buck_typ_voltages),
 	},
 };
 
@@ -257,16 +240,6 @@ static int ab3100_is_enabled_regulator(struct regulator_dev *reg)
 	return regval & AB3100_REG_ON_MASK;
 }
 
-static int ab3100_list_voltage_regulator(struct regulator_dev *reg,
-					 unsigned selector)
-{
-	struct ab3100_regulator *abreg = reg->reg_data;
-
-	if (selector >= abreg->voltages_len)
-		return -EINVAL;
-	return abreg->typ_voltages[selector];
-}
-
 static int ab3100_get_voltage_regulator(struct regulator_dev *reg)
 {
 	struct ab3100_regulator *abreg = reg->reg_data;
@@ -294,14 +267,14 @@ static int ab3100_get_voltage_regulator(struct regulator_dev *reg)
 	regval &= 0xE0;
 	regval >>= 5;
 
-	if (regval >= abreg->voltages_len) {
+	if (regval >= reg->desc->n_voltages) {
 		dev_err(&reg->dev,
 			"regulator register %02x contains an illegal voltage setting\n",
 			abreg->regreg);
 		return -EINVAL;
 	}
 
-	return abreg->typ_voltages[regval];
+	return reg->desc->volt_table[regval];
 }
 
 static int ab3100_set_voltage_regulator_sel(struct regulator_dev *reg,
@@ -423,7 +396,7 @@ static struct regulator_ops regulator_ops_variable = {
 	.is_enabled  = ab3100_is_enabled_regulator,
 	.get_voltage = ab3100_get_voltage_regulator,
 	.set_voltage_sel = ab3100_set_voltage_regulator_sel,
-	.list_voltage = ab3100_list_voltage_regulator,
+	.list_voltage = regulator_list_voltage_table,
 	.enable_time = ab3100_enable_time_regulator,
 };
 
@@ -434,7 +407,7 @@ static struct regulator_ops regulator_ops_variable_sleepable = {
 	.get_voltage = ab3100_get_voltage_regulator,
 	.set_voltage_sel = ab3100_set_voltage_regulator_sel,
 	.set_suspend_voltage = ab3100_set_suspend_voltage_regulator,
-	.list_voltage = ab3100_list_voltage_regulator,
+	.list_voltage = regulator_list_voltage_table,
 	.enable_time = ab3100_enable_time_regulator,
 };
 
@@ -479,6 +452,7 @@ ab3100_regulator_desc[AB3100_NUM_REGULATORS] = {
 		.id   = AB3100_LDO_E,
 		.ops  = &regulator_ops_variable_sleepable,
 		.n_voltages = ARRAY_SIZE(ldo_e_buck_typ_voltages),
+		.volt_table = ldo_e_buck_typ_voltages,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -487,6 +461,7 @@ ab3100_regulator_desc[AB3100_NUM_REGULATORS] = {
 		.id   = AB3100_LDO_F,
 		.ops  = &regulator_ops_variable,
 		.n_voltages = ARRAY_SIZE(ldo_f_typ_voltages),
+		.volt_table = ldo_f_typ_voltages,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -495,6 +470,7 @@ ab3100_regulator_desc[AB3100_NUM_REGULATORS] = {
 		.id   = AB3100_LDO_G,
 		.ops  = &regulator_ops_variable,
 		.n_voltages = ARRAY_SIZE(ldo_g_typ_voltages),
+		.volt_table = ldo_g_typ_voltages,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -503,6 +479,7 @@ ab3100_regulator_desc[AB3100_NUM_REGULATORS] = {
 		.id   = AB3100_LDO_H,
 		.ops  = &regulator_ops_variable,
 		.n_voltages = ARRAY_SIZE(ldo_h_typ_voltages),
+		.volt_table = ldo_h_typ_voltages,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -511,6 +488,7 @@ ab3100_regulator_desc[AB3100_NUM_REGULATORS] = {
 		.id   = AB3100_LDO_K,
 		.ops  = &regulator_ops_variable,
 		.n_voltages = ARRAY_SIZE(ldo_k_typ_voltages),
+		.volt_table = ldo_k_typ_voltages,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
-- 
1.7.5.4

[PATCH RFC/RFT 3/7] regulator: ab8500: Use regulator_list_voltage_table()

[Axel Lin]

Signed-off-by: Axel Lin <axel.lin@gmail.com>
---
 drivers/regulator/ab8500.c |   64 ++++++++++++++++---------------------------
 1 files changed, 24 insertions(+), 40 deletions(-)

diff --git a/drivers/regulator/ab8500.c b/drivers/regulator/ab8500.c
index e1b8c54..da883e6 100644
--- a/drivers/regulator/ab8500.c
+++ b/drivers/regulator/ab8500.c
@@ -40,8 +40,6 @@
  * @voltage_bank: bank to control regulator voltage
  * @voltage_reg: register to control regulator voltage
  * @voltage_mask: mask to control regulator voltage
- * @voltages: supported voltage table
- * @voltages_len: number of supported voltages for the regulator
  * @delay: startup/set voltage delay in us
  */
 struct ab8500_regulator_info {
@@ -58,13 +56,11 @@ struct ab8500_regulator_info {
 	u8 voltage_bank;
 	u8 voltage_reg;
 	u8 voltage_mask;
-	int const *voltages;
-	int voltages_len;
 	unsigned int delay;
 };
 
 /* voltage tables for the vauxn/vintcore supplies */
-static const int ldo_vauxn_voltages[] = {
+static const unsigned int ldo_vauxn_voltages[] = {
 	1100000,
 	1200000,
 	1300000,
@@ -83,7 +79,7 @@ static const int ldo_vauxn_voltages[] = {
 	3300000,
 };
 
-static const int ldo_vaux3_voltages[] = {
+static const unsigned int ldo_vaux3_voltages[] = {
 	1200000,
 	1500000,
 	1800000,
@@ -94,7 +90,7 @@ static const int ldo_vaux3_voltages[] = {
 	2910000,
 };
 
-static const int ldo_vintcore_voltages[] = {
+static const unsigned int ldo_vintcore_voltages[] = {
 	1200000,
 	1225000,
 	1250000,
@@ -185,25 +181,6 @@ static int ab8500_regulator_is_enabled(struct regulator_dev *rdev)
 		return false;
 }
 
-static int ab8500_list_voltage(struct regulator_dev *rdev, unsigned selector)
-{
-	struct ab8500_regulator_info *info = rdev_get_drvdata(rdev);
-
-	if (info == NULL) {
-		dev_err(rdev_get_dev(rdev), "regulator info null pointer\n");
-		return -EINVAL;
-	}
-
-	/* return the uV for the fixed regulators */
-	if (info->fixed_uV)
-		return info->fixed_uV;
-
-	if (selector >= info->voltages_len)
-		return -EINVAL;
-
-	return info->voltages[selector];
-}
-
 static int ab8500_regulator_get_voltage_sel(struct regulator_dev *rdev)
 {
 	int ret, val;
@@ -296,11 +273,24 @@ static struct regulator_ops ab8500_regulator_ops = {
 	.is_enabled	= ab8500_regulator_is_enabled,
 	.get_voltage_sel = ab8500_regulator_get_voltage_sel,
 	.set_voltage_sel = ab8500_regulator_set_voltage_sel,
-	.list_voltage	= ab8500_list_voltage,
+	.list_voltage	= regulator_list_voltage_table,
 	.enable_time	= ab8500_regulator_enable_time,
 	.set_voltage_time_sel = ab8500_regulator_set_voltage_time_sel,
 };
 
+static int ab8500_fixed_list_voltage(struct regulator_dev *rdev,
+				     unsigned selector)
+{
+	struct ab8500_regulator_info *info = rdev_get_drvdata(rdev);
+
+	if (info == NULL) {
+		dev_err(rdev_get_dev(rdev), "regulator info null pointer\n");
+		return -EINVAL;
+	}
+
+	return info->fixed_uV;
+}
+
 static int ab8500_fixed_get_voltage(struct regulator_dev *rdev)
 {
 	struct ab8500_regulator_info *info = rdev_get_drvdata(rdev);
@@ -318,7 +308,7 @@ static struct regulator_ops ab8500_regulator_fixed_ops = {
 	.disable	= ab8500_regulator_disable,
 	.is_enabled	= ab8500_regulator_is_enabled,
 	.get_voltage	= ab8500_fixed_get_voltage,
-	.list_voltage	= ab8500_list_voltage,
+	.list_voltage	= ab8500_fixed_list_voltage,
 	.enable_time	= ab8500_regulator_enable_time,
 	.set_voltage_time_sel = ab8500_regulator_set_voltage_time_sel,
 };
@@ -329,7 +319,7 @@ static struct ab8500_regulator_info
 	 * Variable Voltage Regulators
 	 *   name, min mV, max mV,
 	 *   update bank, reg, mask, enable val
-	 *   volt bank, reg, mask, table, table length
+	 *   volt bank, reg, mask
 	 */
 	[AB8500_LDO_AUX1] = {
 		.desc = {
@@ -339,6 +329,7 @@ static struct ab8500_regulator_info
 			.id		= AB8500_LDO_AUX1,
 			.owner		= THIS_MODULE,
 			.n_voltages	= ARRAY_SIZE(ldo_vauxn_voltages),
+			.volt_table	= ldo_vauxn_voltages,
 		},
 		.min_uV			= 1100000,
 		.max_uV			= 3300000,
@@ -349,8 +340,6 @@ static struct ab8500_regulator_info
 		.voltage_bank		= 0x04,
 		.voltage_reg		= 0x1f,
 		.voltage_mask		= 0x0f,
-		.voltages		= ldo_vauxn_voltages,
-		.voltages_len		= ARRAY_SIZE(ldo_vauxn_voltages),
 	},
 	[AB8500_LDO_AUX2] = {
 		.desc = {
@@ -360,6 +349,7 @@ static struct ab8500_regulator_info
 			.id		= AB8500_LDO_AUX2,
 			.owner		= THIS_MODULE,
 			.n_voltages	= ARRAY_SIZE(ldo_vauxn_voltages),
+			.volt_table	= ldo_vauxn_voltages,
 		},
 		.min_uV			= 1100000,
 		.max_uV			= 3300000,
@@ -370,8 +360,6 @@ static struct ab8500_regulator_info
 		.voltage_bank		= 0x04,
 		.voltage_reg		= 0x20,
 		.voltage_mask		= 0x0f,
-		.voltages		= ldo_vauxn_voltages,
-		.voltages_len		= ARRAY_SIZE(ldo_vauxn_voltages),
 	},
 	[AB8500_LDO_AUX3] = {
 		.desc = {
@@ -381,6 +369,7 @@ static struct ab8500_regulator_info
 			.id		= AB8500_LDO_AUX3,
 			.owner		= THIS_MODULE,
 			.n_voltages	= ARRAY_SIZE(ldo_vaux3_voltages),
+			.volt_table	= ldo_vaux3_voltages,
 		},
 		.min_uV			= 1100000,
 		.max_uV			= 3300000,
@@ -391,8 +380,6 @@ static struct ab8500_regulator_info
 		.voltage_bank		= 0x04,
 		.voltage_reg		= 0x21,
 		.voltage_mask		= 0x07,
-		.voltages		= ldo_vaux3_voltages,
-		.voltages_len		= ARRAY_SIZE(ldo_vaux3_voltages),
 	},
 	[AB8500_LDO_INTCORE] = {
 		.desc = {
@@ -402,6 +389,7 @@ static struct ab8500_regulator_info
 			.id		= AB8500_LDO_INTCORE,
 			.owner		= THIS_MODULE,
 			.n_voltages	= ARRAY_SIZE(ldo_vintcore_voltages),
+			.volt_table	= ldo_vintcore_voltages,
 		},
 		.min_uV			= 1100000,
 		.max_uV			= 3300000,
@@ -412,8 +400,6 @@ static struct ab8500_regulator_info
 		.voltage_bank		= 0x03,
 		.voltage_reg		= 0x80,
 		.voltage_mask		= 0x38,
-		.voltages		= ldo_vintcore_voltages,
-		.voltages_len		= ARRAY_SIZE(ldo_vintcore_voltages),
 	},
 
 	/*
@@ -769,9 +755,7 @@ static __devinit int ab8500_regulator_register(struct platform_device *pdev,
 		if (info->desc.id == AB8500_LDO_AUX3) {
 			info->desc.n_voltages =
 				ARRAY_SIZE(ldo_vauxn_voltages);
-			info->voltages = ldo_vauxn_voltages;
-			info->voltages_len =
-				ARRAY_SIZE(ldo_vauxn_voltages);
+			info->desc.volt_table = ldo_vauxn_voltages;
 			info->voltage_mask = 0xf;
 		}
 	}
-- 
1.7.5.4

[PATCH RFC/RFT 4/7] regulator: lp3971: Use regulator_list_voltage_table()

[Axel Lin]

Signed-off-by: Axel Lin <axel.lin@gmail.com>
---
 drivers/regulator/lp3971.c |   64 +++++++++++++++----------------------------
 1 files changed, 22 insertions(+), 42 deletions(-)

diff --git a/drivers/regulator/lp3971.c b/drivers/regulator/lp3971.c
index 981bea9..87d0a5b 100644
--- a/drivers/regulator/lp3971.c
+++ b/drivers/regulator/lp3971.c
@@ -65,11 +65,11 @@ static const int buck_base_addr[] = {
 #define LP3971_BUCK_TARGET_VOL1_REG(x) (buck_base_addr[x])
 #define LP3971_BUCK_TARGET_VOL2_REG(x) (buck_base_addr[x]+1)
 
-static const int buck_voltage_map[] = {
-	   0,  800,  850,  900,  950, 1000, 1050, 1100,
-	1150, 1200, 1250, 1300, 1350, 1400, 1450, 1500,
-	1550, 1600, 1650, 1700, 1800, 1900, 2500, 2800,
-	3000, 3300,
+static const unsigned int buck_voltage_map[] = {
+	      0,  800000,  850000,  900000,  950000, 1000000, 1050000, 1100000,
+	1150000, 1200000, 1250000, 1300000, 1350000, 1400000, 1450000, 1500000,
+	1550000, 1600000, 1650000, 1700000, 1800000, 1900000, 2500000, 2800000,
+	3000000, 3300000,
 };
 
 #define BUCK_TARGET_VOL_MASK 0x3f
@@ -98,39 +98,19 @@ static const int buck_voltage_map[] = {
 #define LDO_VOL_CONTR_SHIFT(x) ((x & 1) << 2)
 #define LDO_VOL_CONTR_MASK 0x0f
 
-static const int ldo45_voltage_map[] = {
-	1000, 1050, 1100, 1150, 1200, 1250, 1300, 1350,
-	1400, 1500, 1800, 1900, 2500, 2800, 3000, 3300,
+static const unsigned int ldo45_voltage_map[] = {
+	1000000, 1050000, 1100000, 1150000, 1200000, 1250000, 1300000, 1350000,
+	1400000, 1500000, 1800000, 1900000, 2500000, 2800000, 3000000, 3300000,
 };
 
-static const int ldo123_voltage_map[] = {
-	1800, 1900, 2000, 2100, 2200, 2300, 2400, 2500,
-	2600, 2700, 2800, 2900, 3000, 3100, 3200, 3300,
+static const unsigned int ldo123_voltage_map[] = {
+	1800000, 1900000, 2000000, 2100000, 2200000, 2300000, 2400000, 2500000,
+	2600000, 2700000, 2800000, 2900000, 3000000, 3100000, 3200000, 3300000,
 };
 
-static const int *ldo_voltage_map[] = {
-	ldo123_voltage_map, /* LDO1 */
-	ldo123_voltage_map, /* LDO2 */
-	ldo123_voltage_map, /* LDO3 */
-	ldo45_voltage_map, /* LDO4 */
-	ldo45_voltage_map, /* LDO5 */
-};
-
-#define LDO_VOL_VALUE_MAP(x) (ldo_voltage_map[(x - LP3971_LDO1)])
-
 #define LDO_VOL_MIN_IDX 0x00
 #define LDO_VOL_MAX_IDX 0x0f
 
-static int lp3971_ldo_list_voltage(struct regulator_dev *dev, unsigned index)
-{
-	int ldo = rdev_get_id(dev) - LP3971_LDO1;
-
-	if (index > LDO_VOL_MAX_IDX)
-		return -EINVAL;
-
-	return 1000 * LDO_VOL_VALUE_MAP(ldo)[index];
-}
-
 static int lp3971_ldo_is_enabled(struct regulator_dev *dev)
 {
 	struct lp3971 *lp3971 = rdev_get_drvdata(dev);
@@ -169,7 +149,7 @@ static int lp3971_ldo_get_voltage(struct regulator_dev *dev)
 	reg = lp3971_reg_read(lp3971, LP3971_LDO_VOL_CONTR_REG(ldo));
 	val = (reg >> LDO_VOL_CONTR_SHIFT(ldo)) & LDO_VOL_CONTR_MASK;
 
-	return 1000 * LDO_VOL_VALUE_MAP(ldo)[val];
+	return dev->desc->volt_table[val];
 }
 
 static int lp3971_ldo_set_voltage_sel(struct regulator_dev *dev,
@@ -184,7 +164,7 @@ static int lp3971_ldo_set_voltage_sel(struct regulator_dev *dev,
 }
 
 static struct regulator_ops lp3971_ldo_ops = {
-	.list_voltage = lp3971_ldo_list_voltage,
+	.list_voltage = regulator_list_voltage_table,
 	.is_enabled = lp3971_ldo_is_enabled,
 	.enable = lp3971_ldo_enable,
 	.disable = lp3971_ldo_disable,
@@ -192,14 +172,6 @@ static struct regulator_ops lp3971_ldo_ops = {
 	.set_voltage_sel = lp3971_ldo_set_voltage_sel,
 };
 
-static int lp3971_dcdc_list_voltage(struct regulator_dev *dev, unsigned index)
-{
-	if (index < BUCK_TARGET_VOL_MIN_IDX || index > BUCK_TARGET_VOL_MAX_IDX)
-		return -EINVAL;
-
-	return 1000 * buck_voltage_map[index];
-}
-
 static int lp3971_dcdc_is_enabled(struct regulator_dev *dev)
 {
 	struct lp3971 *lp3971 = rdev_get_drvdata(dev);
@@ -273,7 +245,7 @@ static int lp3971_dcdc_set_voltage_sel(struct regulator_dev *dev,
 }
 
 static struct regulator_ops lp3971_dcdc_ops = {
-	.list_voltage = lp3971_dcdc_list_voltage,
+	.list_voltage = regulator_list_voltage_table,
 	.is_enabled = lp3971_dcdc_is_enabled,
 	.enable = lp3971_dcdc_enable,
 	.disable = lp3971_dcdc_disable,
@@ -287,6 +259,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3971_LDO1,
 		.ops = &lp3971_ldo_ops,
 		.n_voltages = ARRAY_SIZE(ldo123_voltage_map),
+		.volt_table = ldo123_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -295,6 +268,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3971_LDO2,
 		.ops = &lp3971_ldo_ops,
 		.n_voltages = ARRAY_SIZE(ldo123_voltage_map),
+		.volt_table = ldo123_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -303,6 +277,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3971_LDO3,
 		.ops = &lp3971_ldo_ops,
 		.n_voltages = ARRAY_SIZE(ldo123_voltage_map),
+		.volt_table = ldo123_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -311,6 +286,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3971_LDO4,
 		.ops = &lp3971_ldo_ops,
 		.n_voltages = ARRAY_SIZE(ldo45_voltage_map),
+		.volt_table = ldo45_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -319,6 +295,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3971_LDO5,
 		.ops = &lp3971_ldo_ops,
 		.n_voltages = ARRAY_SIZE(ldo45_voltage_map),
+		.volt_table = ldo45_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -327,6 +304,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3971_DCDC1,
 		.ops = &lp3971_dcdc_ops,
 		.n_voltages = ARRAY_SIZE(buck_voltage_map),
+		.volt_table = buck_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -335,6 +313,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3971_DCDC2,
 		.ops = &lp3971_dcdc_ops,
 		.n_voltages = ARRAY_SIZE(buck_voltage_map),
+		.volt_table = buck_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -343,6 +322,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3971_DCDC3,
 		.ops = &lp3971_dcdc_ops,
 		.n_voltages = ARRAY_SIZE(buck_voltage_map),
+		.volt_table = buck_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
-- 
1.7.5.4

[PATCH RFC/RFT 5/7] regulator: lp3972: Use regulator_list_voltage_table()

[Axel Lin]

Signed-off-by: Axel Lin <axel.lin@gmail.com>
---
 drivers/regulator/lp3972.c |  102 +++++++++++++++----------------------------
 1 files changed, 36 insertions(+), 66 deletions(-)

diff --git a/drivers/regulator/lp3972.c b/drivers/regulator/lp3972.c
index de073df..3cdc755 100644
--- a/drivers/regulator/lp3972.c
+++ b/drivers/regulator/lp3972.c
@@ -74,54 +74,40 @@ struct lp3972 {
 #define LP3972_OVER2_LDO4_EN	BIT(4)
 #define LP3972_OVER1_S_EN	BIT(2)
 
-static const int ldo1_voltage_map[] = {
-	1700, 1725, 1750, 1775, 1800, 1825, 1850, 1875,
-	1900, 1925, 1950, 1975, 2000,
+static const unsigned int ldo1_voltage_map[] = {
+	1700000, 1725000, 1750000, 1775000, 1800000, 1825000, 1850000, 1875000,
+	1900000, 1925000, 1950000, 1975000, 2000000,
 };
 
-static const int ldo23_voltage_map[] = {
-	1800, 1900, 2000, 2100, 2200, 2300, 2400, 2500,
-	2600, 2700, 2800, 2900, 3000, 3100, 3200, 3300,
+static const unsigned int ldo23_voltage_map[] = {
+	1800000, 1900000, 2000000, 2100000, 2200000, 2300000, 2400000, 2500000,
+	2600000, 2700000, 2800000, 2900000, 3000000, 3100000, 3200000, 3300000,
 };
 
-static const int ldo4_voltage_map[] = {
-	1000, 1050, 1100, 1150, 1200, 1250, 1300, 1350,
-	1400, 1500, 1800, 1900, 2500, 2800, 3000, 3300,
+static const unsigned int ldo4_voltage_map[] = {
+	1000000, 1050000, 1100000, 1150000, 1200000, 1250000, 1300000, 1350000,
+	1400000, 1500000, 1800000, 1900000, 2500000, 2800000, 3000000, 3300000,
 };
 
-static const int ldo5_voltage_map[] = {
-	   0,    0,    0,    0,    0,  850,  875,  900,
-	 925,  950,  975, 1000, 1025, 1050, 1075, 1100,
-	1125, 1150, 1175, 1200, 1225, 1250, 1275, 1300,
-	1325, 1350, 1375, 1400, 1425, 1450, 1475, 1500,
+static const unsigned int ldo5_voltage_map[] = {
+	      0,       0,       0,       0,       0,  850000,  875000,  900000,
+	 925000,  950000,  975000, 1000000, 1025000, 1050000, 1075000, 1100000,
+	1125000, 1150000, 1175000, 1200000, 1225000, 1250000, 1275000, 1300000,
+	1325000, 1350000, 1375000, 1400000, 1425000, 1450000, 1475000, 1500000,
 };
 
-static const int buck1_voltage_map[] = {
-	 725,  750,  775,  800,  825,  850,  875,  900,
-	 925,  950,  975, 1000, 1025, 1050, 1075, 1100,
-	1125, 1150, 1175, 1200, 1225, 1250, 1275, 1300,
-	1325, 1350, 1375, 1400, 1425, 1450, 1475, 1500,
+static const unsigned int buck1_voltage_map[] = {
+	 725000,  750000,  775000,  800000,  825000,  850000,  875000,  900000,
+	 925000,  950000,  975000, 1000000, 1025000, 1050000, 1075000, 1100000,
+	1125000, 1150000, 1175000, 1200000, 1225000, 1250000, 1275000, 1300000,
+	1325000, 1350000, 1375000, 1400000, 1425000, 1450000, 1475000, 1500000,
 };
 
-static const int buck23_voltage_map[] = {
-	   0,  800,  850,  900,  950, 1000, 1050, 1100,
-	1150, 1200, 1250, 1300, 1350, 1400, 1450, 1500,
-	1550, 1600, 1650, 1700, 1800, 1900, 2500, 2800,
-	3000, 3300,
-};
-
-static const int *ldo_voltage_map[] = {
-	ldo1_voltage_map,
-	ldo23_voltage_map,
-	ldo23_voltage_map,
-	ldo4_voltage_map,
-	ldo5_voltage_map,
-};
-
-static const int *buck_voltage_map[] = {
-	buck1_voltage_map,
-	buck23_voltage_map,
-	buck23_voltage_map,
+static const unsigned int buck23_voltage_map[] = {
+	      0,  800000,  850000,  900000,  950000, 1000000, 1050000, 1100000,
+	1150000, 1200000, 1250000, 1300000, 1350000, 1400000, 1450000, 1500000,
+	1550000, 1600000, 1650000, 1700000, 1800000, 1900000, 2500000, 2800000,
+	3000000, 3300000,
 };
 
 static const int ldo_output_enable_mask[] = {
@@ -160,7 +146,6 @@ static const int buck_base_addr[] = {
 	LP3972_B3TV_REG,
 };
 
-#define LP3972_LDO_VOL_VALUE_MAP(x) (ldo_voltage_map[x])
 #define LP3972_LDO_OUTPUT_ENABLE_MASK(x) (ldo_output_enable_mask[x])
 #define LP3972_LDO_OUTPUT_ENABLE_REG(x) (ldo_output_enable_addr[x])
 
@@ -177,7 +162,6 @@ static const int buck_base_addr[] = {
 #define LP3972_LDO_VOL_MIN_IDX(x) (((x) == 4) ? 0x05 : 0x00)
 #define LP3972_LDO_VOL_MAX_IDX(x) ((x) ? (((x) == 4) ? 0x1f : 0x0f) : 0x0c)
 
-#define LP3972_BUCK_VOL_VALUE_MAP(x) (buck_voltage_map[x])
 #define LP3972_BUCK_VOL_ENABLE_REG(x) (buck_vol_enable_addr[x])
 #define LP3972_BUCK_VOL1_REG(x) (buck_base_addr[x])
 #define LP3972_BUCK_VOL_MASK 0x1f
@@ -242,17 +226,6 @@ static int lp3972_set_bits(struct lp3972 *lp3972, u8 reg, u16 mask, u16 val)
 	return ret;
 }
 
-static int lp3972_ldo_list_voltage(struct regulator_dev *dev, unsigned index)
-{
-	int ldo = rdev_get_id(dev) - LP3972_LDO1;
-
-	if (index < LP3972_LDO_VOL_MIN_IDX(ldo) ||
-	    index > LP3972_LDO_VOL_MAX_IDX(ldo))
-		return -EINVAL;
-
-	return 1000 * LP3972_LDO_VOL_VALUE_MAP(ldo)[index];
-}
-
 static int lp3972_ldo_is_enabled(struct regulator_dev *dev)
 {
 	struct lp3972 *lp3972 = rdev_get_drvdata(dev);
@@ -294,7 +267,7 @@ static int lp3972_ldo_get_voltage(struct regulator_dev *dev)
 	reg = lp3972_reg_read(lp3972, LP3972_LDO_VOL_CONTR_REG(ldo));
 	val = (reg >> LP3972_LDO_VOL_CONTR_SHIFT(ldo)) & mask;
 
-	return 1000 * LP3972_LDO_VOL_VALUE_MAP(ldo)[val];
+	return dev->desc->volt_table[val];
 }
 
 static int lp3972_ldo_set_voltage_sel(struct regulator_dev *dev,
@@ -337,7 +310,7 @@ static int lp3972_ldo_set_voltage_sel(struct regulator_dev *dev,
 }
 
 static struct regulator_ops lp3972_ldo_ops = {
-	.list_voltage = lp3972_ldo_list_voltage,
+	.list_voltage = regulator_list_voltage_table,
 	.is_enabled = lp3972_ldo_is_enabled,
 	.enable = lp3972_ldo_enable,
 	.disable = lp3972_ldo_disable,
@@ -345,17 +318,6 @@ static struct regulator_ops lp3972_ldo_ops = {
 	.set_voltage_sel = lp3972_ldo_set_voltage_sel,
 };
 
-static int lp3972_dcdc_list_voltage(struct regulator_dev *dev, unsigned index)
-{
-	int buck = rdev_get_id(dev) - LP3972_DCDC1;
-
-	if (index < LP3972_BUCK_VOL_MIN_IDX(buck) ||
-	    index > LP3972_BUCK_VOL_MAX_IDX(buck))
-		return -EINVAL;
-
-	return 1000 * buck_voltage_map[buck][index];
-}
-
 static int lp3972_dcdc_is_enabled(struct regulator_dev *dev)
 {
 	struct lp3972 *lp3972 = rdev_get_drvdata(dev);
@@ -401,7 +363,7 @@ static int lp3972_dcdc_get_voltage(struct regulator_dev *dev)
 	reg = lp3972_reg_read(lp3972, LP3972_BUCK_VOL1_REG(buck));
 	reg &= LP3972_BUCK_VOL_MASK;
 	if (reg <= LP3972_BUCK_VOL_MAX_IDX(buck))
-		val = 1000 * buck_voltage_map[buck][reg];
+		val = dev->desc->volt_table[reg];
 	else {
 		val = 0;
 		dev_warn(&dev->dev, "chip reported incorrect voltage value."
@@ -436,7 +398,7 @@ static int lp3972_dcdc_set_voltage_sel(struct regulator_dev *dev,
 }
 
 static struct regulator_ops lp3972_dcdc_ops = {
-	.list_voltage = lp3972_dcdc_list_voltage,
+	.list_voltage = regulator_list_voltage_table,
 	.is_enabled = lp3972_dcdc_is_enabled,
 	.enable = lp3972_dcdc_enable,
 	.disable = lp3972_dcdc_disable,
@@ -450,6 +412,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3972_LDO1,
 		.ops = &lp3972_ldo_ops,
 		.n_voltages = ARRAY_SIZE(ldo1_voltage_map),
+		.volt_table = ldo1_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -458,6 +421,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3972_LDO2,
 		.ops = &lp3972_ldo_ops,
 		.n_voltages = ARRAY_SIZE(ldo23_voltage_map),
+		.volt_table = ldo23_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -466,6 +430,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3972_LDO3,
 		.ops = &lp3972_ldo_ops,
 		.n_voltages = ARRAY_SIZE(ldo23_voltage_map),
+		.volt_table = ldo23_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -474,6 +439,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3972_LDO4,
 		.ops = &lp3972_ldo_ops,
 		.n_voltages = ARRAY_SIZE(ldo4_voltage_map),
+		.volt_table = ldo4_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -482,6 +448,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3972_LDO5,
 		.ops = &lp3972_ldo_ops,
 		.n_voltages = ARRAY_SIZE(ldo5_voltage_map),
+		.volt_table = ldo5_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -490,6 +457,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3972_DCDC1,
 		.ops = &lp3972_dcdc_ops,
 		.n_voltages = ARRAY_SIZE(buck1_voltage_map),
+		.volt_table = buck1_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -498,6 +466,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3972_DCDC2,
 		.ops = &lp3972_dcdc_ops,
 		.n_voltages = ARRAY_SIZE(buck23_voltage_map),
+		.volt_table = buck23_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
@@ -506,6 +475,7 @@ static const struct regulator_desc regulators[] = {
 		.id = LP3972_DCDC3,
 		.ops = &lp3972_dcdc_ops,
 		.n_voltages = ARRAY_SIZE(buck23_voltage_map),
+		.volt_table = buck23_voltage_map,
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 	},
-- 
1.7.5.4

[PATCH RFC/RFT 6/7] regulator: tps6105x: Use regulator_list_voltage_table()

[Axel Lin]

Signed-off-by: Axel Lin <axel.lin@gmail.com>
---
 drivers/regulator/tps6105x-regulator.c |   14 +++-----------
 1 files changed, 3 insertions(+), 11 deletions(-)

diff --git a/drivers/regulator/tps6105x-regulator.c b/drivers/regulator/tps6105x-regulator.c
index d840d84..1378409 100644
--- a/drivers/regulator/tps6105x-regulator.c
+++ b/drivers/regulator/tps6105x-regulator.c
@@ -20,7 +20,7 @@
 #include <linux/mfd/core.h>
 #include <linux/mfd/tps6105x.h>
 
-static const int tps6105x_voltages[] = {
+static const unsigned int tps6105x_voltages[] = {
 	4500000,
 	5000000,
 	5250000,
@@ -105,22 +105,13 @@ static int tps6105x_regulator_set_voltage_sel(struct regulator_dev *rdev,
 	return 0;
 }
 
-static int tps6105x_regulator_list_voltage(struct regulator_dev *rdev,
-					   unsigned selector)
-{
-	if (selector >= ARRAY_SIZE(tps6105x_voltages))
-		return -EINVAL;
-
-	return tps6105x_voltages[selector];
-}
-
 static struct regulator_ops tps6105x_regulator_ops = {
 	.enable		= tps6105x_regulator_enable,
 	.disable	= tps6105x_regulator_disable,
 	.is_enabled	= tps6105x_regulator_is_enabled,
 	.get_voltage_sel = tps6105x_regulator_get_voltage_sel,
 	.set_voltage_sel = tps6105x_regulator_set_voltage_sel,
-	.list_voltage	= tps6105x_regulator_list_voltage,
+	.list_voltage	= regulator_list_voltage_table,
 };
 
 static const struct regulator_desc tps6105x_regulator_desc = {
@@ -130,6 +121,7 @@ static const struct regulator_desc tps6105x_regulator_desc = {
 	.id		= 0,
 	.owner		= THIS_MODULE,
 	.n_voltages	= ARRAY_SIZE(tps6105x_voltages),
+	.volt_table	= tps6105x_voltages,
 };
 
 /*
-- 
1.7.5.4

[PATCH RFC/RFT 7/7] regulator: tps6507x: Use regulator_list_voltage_table()

[Axel Lin]

Signed-off-by: Axel Lin <axel.lin@gmail.com>
---
 drivers/regulator/tps6507x-regulator.c |  100 ++++++++++++++------------------
 1 files changed, 43 insertions(+), 57 deletions(-)

diff --git a/drivers/regulator/tps6507x-regulator.c b/drivers/regulator/tps6507x-regulator.c
index da38be1..c771e10 100644
--- a/drivers/regulator/tps6507x-regulator.c
+++ b/drivers/regulator/tps6507x-regulator.c
@@ -43,50 +43,50 @@
 /* Number of total regulators available */
 #define TPS6507X_NUM_REGULATOR		(TPS6507X_NUM_DCDC + TPS6507X_NUM_LDO)
 
-/* Supported voltage values for regulators (in milliVolts) */
-static const u16 VDCDCx_VSEL_table[] = {
-	725, 750, 775, 800,
-	825, 850, 875, 900,
-	925, 950, 975, 1000,
-	1025, 1050, 1075, 1100,
-	1125, 1150, 1175, 1200,
-	1225, 1250, 1275, 1300,
-	1325, 1350, 1375, 1400,
-	1425, 1450, 1475, 1500,
-	1550, 1600, 1650, 1700,
-	1750, 1800, 1850, 1900,
-	1950, 2000, 2050, 2100,
-	2150, 2200, 2250, 2300,
-	2350, 2400, 2450, 2500,
-	2550, 2600, 2650, 2700,
-	2750, 2800, 2850, 2900,
-	3000, 3100, 3200, 3300,
+/* Supported voltage values for regulators (in microVolts) */
+static const unsigned int VDCDCx_VSEL_table[] = {
+	725000, 750000, 775000, 800000,
+	825000, 850000, 875000, 900000,
+	925000, 950000, 975000, 1000000,
+	1025000, 1050000, 1075000, 1100000,
+	1125000, 1150000, 1175000, 1200000,
+	1225000, 1250000, 1275000, 1300000,
+	1325000, 1350000, 1375000, 1400000,
+	1425000, 1450000, 1475000, 1500000,
+	1550000, 1600000, 1650000, 1700000,
+	1750000, 1800000, 1850000, 1900000,
+	1950000, 2000000, 2050000, 2100000,
+	2150000, 2200000, 2250000, 2300000,
+	2350000, 2400000, 2450000, 2500000,
+	2550000, 2600000, 2650000, 2700000,
+	2750000, 2800000, 2850000, 2900000,
+	3000000, 3100000, 3200000, 3300000,
 };
 
-static const u16 LDO1_VSEL_table[] = {
-	1000, 1100, 1200, 1250,
-	1300, 1350, 1400, 1500,
-	1600, 1800, 2500, 2750,
-	2800, 3000, 3100, 3300,
+static const unsigned int LDO1_VSEL_table[] = {
+	1000000, 1100000, 1200000, 1250000,
+	1300000, 1350000, 1400000, 1500000,
+	1600000, 1800000, 2500000, 2750000,
+	2800000, 3000000, 3100000, 3300000,
 };
 
-static const u16 LDO2_VSEL_table[] = {
-	725, 750, 775, 800,
-	825, 850, 875, 900,
-	925, 950, 975, 1000,
-	1025, 1050, 1075, 1100,
-	1125, 1150, 1175, 1200,
-	1225, 1250, 1275, 1300,
-	1325, 1350, 1375, 1400,
-	1425, 1450, 1475, 1500,
-	1550, 1600, 1650, 1700,
-	1750, 1800, 1850, 1900,
-	1950, 2000, 2050, 2100,
-	2150, 2200, 2250, 2300,
-	2350, 2400, 2450, 2500,
-	2550, 2600, 2650, 2700,
-	2750, 2800, 2850, 2900,
-	3000, 3100, 3200, 3300,
+static const unsigned int LDO2_VSEL_table[] = {
+	725000, 750000, 775000, 800000,
+	825000, 850000, 875000, 900000,
+	925000, 950000, 975000, 1000000,
+	1025000, 1050000, 1075000, 1100000,
+	1125000, 1150000, 1175000, 1200000,
+	1225000, 1250000, 1275000, 1300000,
+	1325000, 1350000, 1375000, 1400000,
+	1425000, 1450000, 1475000, 1500000,
+	1550000, 1600000, 1650000, 1700000,
+	1750000, 1800000, 1850000, 1900000,
+	1950000, 2000000, 2050000, 2100000,
+	2150000, 2200000, 2250000, 2300000,
+	2350000, 2400000, 2450000, 2500000,
+	2550000, 2600000, 2650000, 2700000,
+	2750000, 2800000, 2850000, 2900000,
+	3000000, 3100000, 3200000, 3300000,
 };
 
 struct tps_info {
@@ -94,7 +94,7 @@ struct tps_info {
 	unsigned min_uV;
 	unsigned max_uV;
 	u8 table_len;
-	const u16 *table;
+	const unsigned int *table;
 
 	/* Does DCDC high or the low register defines output voltage? */
 	bool defdcdc_default;
@@ -375,28 +375,13 @@ static int tps6507x_pmic_set_voltage_sel(struct regulator_dev *dev,
 	return tps6507x_pmic_reg_write(tps, reg, data);
 }
 
-static int tps6507x_pmic_list_voltage(struct regulator_dev *dev,
-					unsigned selector)
-{
-	struct tps6507x_pmic *tps = rdev_get_drvdata(dev);
-	int rid = rdev_get_id(dev);
-
-	if (rid < TPS6507X_DCDC_1 || rid > TPS6507X_LDO_2)
-		return -EINVAL;
-
-	if (selector >= tps->info[rid]->table_len)
-		return -EINVAL;
-	else
-		return tps->info[rid]->table[selector] * 1000;
-}
-
 static struct regulator_ops tps6507x_pmic_ops = {
 	.is_enabled = tps6507x_pmic_is_enabled,
 	.enable = tps6507x_pmic_enable,
 	.disable = tps6507x_pmic_disable,
 	.get_voltage_sel = tps6507x_pmic_get_voltage_sel,
 	.set_voltage_sel = tps6507x_pmic_set_voltage_sel,
-	.list_voltage = tps6507x_pmic_list_voltage,
+	.list_voltage = regulator_list_voltage_table,
 };
 
 static __devinit int tps6507x_pmic_probe(struct platform_device *pdev)
@@ -449,6 +434,7 @@ static __devinit int tps6507x_pmic_probe(struct platform_device *pdev)
 		tps->desc[i].name = info->name;
 		tps->desc[i].id = i;
 		tps->desc[i].n_voltages = info->table_len;
+		tps->desc[i].volt_table = info->table;
 		tps->desc[i].ops = &tps6507x_pmic_ops;
 		tps->desc[i].type = REGULATOR_VOLTAGE;
 		tps->desc[i].owner = THIS_MODULE;
-- 
1.7.5.4

Re: [PATCH RFC/RFT 1/7] regulator: core: Allow drivers to set voltage mapping table in regulator_desc

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 243 bytes --]

On Sun, May 20, 2012 at 10:30:21AM +0800, Axel Lin wrote:
> Some regulator hardware use table based mapping can set volt_table in
> regulator_desc and use regulator_list_voltage_table() for their list_voltage
> callback.

Applied all, thanks!

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH RFC/RFT 2/7] regulator: ab3100: Use regulator_list_voltage_table()

[Linus Walleij]

On Sun, May 20, 2012 at 4:31 AM, Axel Lin <axel.lin@gmail.com> wrote:

> Signed-off-by: Axel Lin <axel.lin@gmail.com>
> ---
>  drivers/regulator/ab3100.c |   50 ++++++++++++-------------------------------
>  1 files changed, 14 insertions(+), 36 deletions(-)

Acked-by: Linus Walleij <linus.walleij@linaro.org>

Thanks,
Linus Walleij

Re: [PATCH RFC/RFT 3/7] regulator: ab8500: Use regulator_list_voltage_table()

[Linus Walleij]

On Sun, May 20, 2012 at 4:33 AM, Axel Lin <axel.lin@gmail.com> wrote:

> Signed-off-by: Axel Lin <axel.lin@gmail.com>
> ---
>  drivers/regulator/ab8500.c |   64 ++++++++++++++++---------------------------

Acked-by: Linus Walleij <linus.walleij@linaro.org>

Hm, probably also already applied, whatever.

Yours,
Linus Walleij

Re: [PATCH RFC/RFT 3/7] regulator: ab8500: Use regulator_list_voltage_table()

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 337 bytes --]

On Mon, May 21, 2012 at 12:43:16PM +0200, Linus Walleij wrote:

> Acked-by: Linus Walleij <linus.walleij@linaro.org>

> Hm, probably also already applied, whatever.

It was but it's not made 3.5 so I'll add your ack - review for the
ab8500 has been a bit patchy so I have been tending to apply things
fairly quickly rather than waiting.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH RFC/RFT 6/7] regulator: tps6105x: Use regulator_list_voltage_table()

[Linus Walleij]

On Sun, May 20, 2012 at 4:37 AM, Axel Lin <axel.lin@gmail.com> wrote:

> Signed-off-by: Axel Lin <axel.lin@gmail.com>
> ---
>  drivers/regulator/tps6105x-regulator.c |   14 +++-----------
>  1 files changed, 3 insertions(+), 11 deletions(-)

Acked-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij