[PATCH 0/4] Implement device tree support for ab8500 BM Devices

[PATCH 0/4] Implement device tree support for ab8500 BM Devices

[Rajanikanth H.V]

From: "Rajanikanth H.V" <rajanikanth.hv@linaro.org>

This patch-set adds device tree binding for ab8500 battery-managed
devices. Removes the redundant platform structure maintained
across bm devices and implements common DT probe routine across all the
modules.

Test status:
a) Tested across 'legacy platform data' and DT binding support
	a.1) ab8500_charger driver fails to get regulator in the
		legacy platform mode.
b) Interrupt numbers assigned differs between legacy and FDT mode.
    (a) Legacy platform_data Mode:
    root@ME:/ cat /proc/interrupts
               CPU0       CPU1
    483:          0          0    ab8500  ab8500-ponkey-dbf
    484:          0          0    ab8500  ab8500-ponkey-dbr
    485:          0          0    ab8500  BATT_OVV
    494:          0          1    ab8500
    495:          0          0    ab8500  ab8500-rtc
    501:          0         13    ab8500  NCONV_ACCU
    503:          7         22    ab8500  CCEOC
    504:          0          1    ab8500  CC_INT_CALIB
    505:          0          0    ab8500  LOW_BAT_F
    516:          0         34    ab8500  ab8500-gpadc
    556:          0          0    ab8500  usb-link-status
    
    (b) FDT Mode:
    root@ME:/ cat /proc/interrupts
               CPU0       CPU1
      6:          0          0    ab8500  ab8500-ponkey-dbf
      7:          0          0    ab8500  ab8500-ponkey-dbr
      8:          0          0    ab8500  BATT_OVV
    162:          0          7    ab8500  ab8500-gpadc
    163:          0          1    ab8500
    164:          0          0    ab8500  ab8500-rtc
    484:          0          0    ab8500  usb-link-status
    499:          0          4    ab8500  NCONV_ACCU
    500:          0          0    ab8500  LOW_BAT_F
    502:          0          1    ab8500  CC_INT_CALIB
    503:          0          6    ab8500  CCEOC

c) Event handlers across bm-modules have been verified only
   during 'battery discharge process' as 'battery charging process'
   depends on ab8500-usb code

d) observed nested IRQ issue, log below:

root@ME:/ ------------[ cut here ]------------
WARNING: at /home/rhv00000/linaro_work/linux/kernel/irq/manage.c:635 irq_nested_primary_handler+0x20/0x28()
Primary handler called for nested irq 193
Modules linked in:
[<c0014884>] (unwind_backtrace+0x0/0xf8) from [<c001cbb4>] (warn_slowpath_common+0x4c/0x64)
[<c001cbb4>] (warn_slowpath_common+0x4c/0x64) from [<c001cc60>] (warn_slowpath_fmt+0x30/0x40)
[<c001cc60>] (warn_slowpath_fmt+0x30/0x40) from [<c0060f00>] (irq_nested_primary_handler+0x20/0x28)
[<c0060f00>] (irq_nested_primary_handler+0x20/0x28) from [<c0060b80>] (handle_irq_event_percpu+0x50/0x194)
[<c0060b80>] (handle_irq_event_percpu+0x50/0x194) from [<c0060d00>] (handle_irq_event+0x3c/0x5c)
[<c0060d00>] (handle_irq_event+0x3c/0x5c) from [<c0063034>] (handle_simple_irq+0x8c/0xc4)
[<c0063034>] (handle_simple_irq+0x8c/0xc4) from [<c0062d84>] (resend_irqs+0x40/0x68)
[<c0062d84>] (resend_irqs+0x40/0x68) from [<c00236d8>] (tasklet_action+0x84/0x120)
[<c00236d8>] (tasklet_action+0x84/0x120) from [<c0023ae4>] (__do_softirq+0xd8/0x198)
[<c0023ae4>] (__do_softirq+0xd8/0x198) from [<c0023ed4>] (irq_exit+0x90/0x98)
[<c0023ed4>] (irq_exit+0x90/0x98) from [<c000f2cc>] (handle_IRQ+0x50/0xb0)
[<c000f2cc>] (handle_IRQ+0x50/0xb0) from [<c00084f0>] (gic_handle_irq+0x28/0x5c)
[<c00084f0>] (gic_handle_irq+0x28/0x5c) from [<c000df80>] (__irq_svc+0x40/0x70)
Exception stack(0xebc5dea8 to 0xebc5def0)
dea0:                   c0f45340 ebc4cf00 00000000 1f321f32 eb196600 ebc4cf00
dec0: c05a3340 00000002 ebc4c600 00000000 eb1b2c00 ebc5df0c 00000000 ebc5def0
dee0: c0040c7c c02ca5ec 60000013 ffffffff
[<c000df80>] (__irq_svc+0x40/0x70) from [<c02ca5ec>] (_raw_spin_unlock_irq+0x28/0x50)
[<c02ca5ec>] (_raw_spin_unlock_irq+0x28/0x50) from [<c0040c7c>] (finish_task_switch+0x28/0xf0)
[<c0040c7c>] (finish_task_switch+0x28/0xf0) from [<c02c93f0>] (__schedule+0x254/0x548)
[<c02c93f0>] (__schedule+0x254/0x548) from [<c0040088>] (smpboot_thread_fn+0x11c/0x250)
[<c0040088>] (smpboot_thread_fn+0x11c/0x250) from [<c0037fc8>] (kthread+0xa4/0xb0)
[<c0037fc8>] (kthread+0xa4/0xb0) from [<c000e418>] (ret_from_fork+0x14/0x3c)
---[ end trace 1b75b31a2719ed1e ]---

Rajanikanth H.V (4):
  mfd: ab8500: add devicetree support for fuelgauge
  mfd: ab8500: add devicetree support for btemp
  mfd: ab8500: add devicetree support for charger
  mfd: ab8500: add devicetree support for chargalg

 Documentation/devicetree/bindings/mfd/ab8500.txt   |   27 +-
 .../bindings/power_supply/ab8500/btemp.txt         |   16 +
 .../bindings/power_supply/ab8500/chargalg.txt      |   16 +
 .../bindings/power_supply/ab8500/charger.txt       |   25 +
 .../devicetree/bindings/power_supply/ab8500/fg.txt |   58 +++
 arch/arm/boot/dts/dbx5x0.dtsi                      |   26 +
 drivers/mfd/ab8500-core.c                          |   20 +
 drivers/power/Kconfig                              |    6 -
 drivers/power/Makefile                             |    2 +-
 drivers/power/ab8500_bmdata.c                      |  514 ++++++++++++++++++++
 drivers/power/ab8500_btemp.c                       |   75 +--
 drivers/power/ab8500_charger.c                     |   83 ++--
 drivers/power/ab8500_fg.c                          |   81 +--
 drivers/power/abx500_chargalg.c                    |   57 ++-
 include/linux/mfd/abx500.h                         |   34 +-
 15 files changed, 879 insertions(+), 161 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/power_supply/ab8500/btemp.txt
 create mode 100644 Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt
 create mode 100644 Documentation/devicetree/bindings/power_supply/ab8500/charger.txt
 create mode 100644 Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
 create mode 100644 drivers/power/ab8500_bmdata.c

-- 
1.7.10.4

[PATCH 1/4] mfd: ab8500: add devicetree support for fuelgauge

[Rajanikanth H.V]

From: "Rajanikanth H.V" <rajanikanth.hv@linaro.org>

- This patch adds device tree support for fuelgauge driver
- optimize bm devices platform_data usage and of_probe(...)
  Note: of_probe() routine for battery managed devices is made
  common across all bm drivers.
- test status:
  - interrupt numbers assigned differs between legacy and FDT mode.

Signed-off-by: Rajanikanth H.V <rajanikanth.hv@linaro.org>
---
 Documentation/devicetree/bindings/mfd/ab8500.txt   |    7 +-
 .../devicetree/bindings/power_supply/ab8500/fg.txt |   58 +++
 arch/arm/boot/dts/dbx5x0.dtsi                      |   10 +
 drivers/mfd/ab8500-core.c                          |    5 +
 drivers/power/Makefile                             |    2 +-
 drivers/power/ab8500_bmdata.c                      |  514 ++++++++++++++++++++
 drivers/power/ab8500_btemp.c                       |   16 +-
 drivers/power/ab8500_charger.c                     |   16 +-
 drivers/power/ab8500_fg.c                          |   81 +--
 drivers/power/abx500_chargalg.c                    |    7 +-
 include/linux/mfd/abx500.h                         |   36 +-
 11 files changed, 659 insertions(+), 93 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
 create mode 100644 drivers/power/ab8500_bmdata.c

diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt
index ce83c8d..6ca8d81 100644
--- a/Documentation/devicetree/bindings/mfd/ab8500.txt
+++ b/Documentation/devicetree/bindings/mfd/ab8500.txt
@@ -24,7 +24,12 @@ ab8500-bm                :                      :              : Battery Manager
 ab8500-btemp             :                      :              : Battery Temperature
 ab8500-charger           :                      :              : Battery Charger
 ab8500-codec             :                      :              : Audio Codec
-ab8500-fg                :                      :              : Fuel Gauge
+ab8500-fg                : 			: vddadc       : Fuel Gauge
+			 : NCONV_ACCU           :	       : Accumulate N Sample Conversion
+			 : BATT_OVV		:	       : Battery Over Voltage
+			 : LOW_BAT_F		:	       : LOW threshold battery voltage
+			 : CC_INT_CALIB		:	       : Coulomb Counter Internal Calibration
+			 : CCEOC		:	       : Coulomb Counter End of Conversion
 ab8500-gpadc             : HW_CONV_END          : vddadc       : Analogue to Digital Converter
                            SW_CONV_END          :              :
 ab8500-gpio              :                      :              : GPIO Controller
diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt b/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
new file mode 100644
index 0000000..ccafcb9
--- /dev/null
+++ b/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
@@ -0,0 +1,58 @@
+=== AB8500 Fuel Gauge Driver ===
+
+AB8500 is a mixed signal multimedia and power management
+device comprising: power and energy-management-module,
+wall-charger, usb-charger, audio codec, general purpose adc,
+tvout, clock management and sim card interface.
+
+Fuelgauge support is part of energy-management-modules, other
+components of this module are:
+main-charger, usb-combo-charger and battery-temperature-monitoring.
+
+The properties below describes the node for fuelgauge driver.
+
+Required Properties:
+- compatible = This shall be: "stericsson,ab8500-fg"
+- battery = Shall be battery specific information
+	Example:
+	ab8500_fg {
+		compatible = "stericsson,ab8500-fg";
+		battery	   = <&ab8500_battery>;
+	};
+
+dependent node:
+	ab8500_battery: ab8500_battery {
+	};
+	This node will provide information on 'thermistor interface' and
+	'battery technology type' used.
+
+Properties of this node are:
+thermistor-on-batctrl:
+	A boolean value indicating thermistor interface	to battery
+
+	Note:
+	'btemp' and 'batctrl' are the pins interfaced for battery temperature
+	measurement, 'btemp' signal is used when NTC(negative temperature
+	coefficient) resister is interfaced external to battery whereas
+	'batctrl' pin is used when NTC resister is internal to battery.
+
+	Example:
+	ab8500_battery: ab8500_battery {
+		thermistor-on-batctrl;
+	};
+	indicates: NTC resister is internal to battery, 'batctrl' is used
+		for thermal measurement.
+
+	The absence of property 'thermal-on-batctrl' indicates
+	NTC resister is external to battery and  'btemp' signal is used
+	for thermal measurement.
+
+battery-type:
+	This shall be the battery manufacturing technology type,
+	allowed types are:
+		"UNKNOWN" "NiMH" "LION" "LIPO" "LiFe" "NiCd" "LiMn"
+	Example:
+	ab8500_battery: ab8500_battery {
+		stericsson,battery-type = "LIPO";
+	}
+
diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
index 4b0e0ca..155cf53 100644
--- a/arch/arm/boot/dts/dbx5x0.dtsi
+++ b/arch/arm/boot/dts/dbx5x0.dtsi
@@ -352,6 +352,16 @@
 					vddadc-supply = <&ab8500_ldo_tvout_reg>;
 				};
 
+				ab8500_battery: ab8500_battery {
+					stericsson,battery-type = "LIPO";
+					thermistor-on-batctrl;
+				};
+
+				ab8500-fg {
+					compatible = "stericsson,ab8500-fg";
+					battery	   = <&ab8500_battery>;
+				};
+
 				ab8500-usb {
 					compatible = "stericsson,ab8500-usb";
 					interrupts = < 90 0x4
diff --git a/drivers/mfd/ab8500-core.c b/drivers/mfd/ab8500-core.c
index 1667c77..7c3017b 100644
--- a/drivers/mfd/ab8500-core.c
+++ b/drivers/mfd/ab8500-core.c
@@ -1051,8 +1051,13 @@ static struct mfd_cell __devinitdata ab8500_bm_devs[] = {
 	},
 	{
 		.name = "ab8500-fg",
+		.of_compatible = "stericsson,ab8500-fg",
 		.num_resources = ARRAY_SIZE(ab8500_fg_resources),
 		.resources = ab8500_fg_resources,
+#ifndef CONFIG_OF
+		.platform_data = &ab8500_bm_data,
+		.pdata_size = sizeof(ab8500_bm_data),
+#endif
 	},
 	{
 		.name = "ab8500-chargalg",
diff --git a/drivers/power/Makefile b/drivers/power/Makefile
index b949cf8..9103665 100644
--- a/drivers/power/Makefile
+++ b/drivers/power/Makefile
@@ -37,7 +37,7 @@ obj-$(CONFIG_CHARGER_88PM860X)	+= 88pm860x_charger.o
 obj-$(CONFIG_CHARGER_PCF50633)	+= pcf50633-charger.o
 obj-$(CONFIG_BATTERY_JZ4740)	+= jz4740-battery.o
 obj-$(CONFIG_BATTERY_INTEL_MID)	+= intel_mid_battery.o
-obj-$(CONFIG_AB8500_BM)		+= ab8500_charger.o ab8500_btemp.o ab8500_fg.o abx500_chargalg.o
+obj-$(CONFIG_AB8500_BM)		+= ab8500_bmdata.o ab8500_charger.o ab8500_fg.o ab8500_btemp.o abx500_chargalg.o
 obj-$(CONFIG_CHARGER_ISP1704)	+= isp1704_charger.o
 obj-$(CONFIG_CHARGER_MAX8903)	+= max8903_charger.o
 obj-$(CONFIG_CHARGER_TWL4030)	+= twl4030_charger.o
diff --git a/drivers/power/ab8500_bmdata.c b/drivers/power/ab8500_bmdata.c
new file mode 100644
index 0000000..0366270
--- /dev/null
+++ b/drivers/power/ab8500_bmdata.c
@@ -0,0 +1,514 @@
+#include <linux/export.h>
+#include <linux/power_supply.h>
+#include <linux/of.h>
+#include <linux/mfd/abx500.h>
+#include <linux/mfd/abx500/ab8500.h>
+#include <linux/mfd/abx500/ab8500-bm.h>
+
+/*
+ * These are the defined batteries that uses a NTC and ID resistor placed
+ * inside of the battery pack.
+ * Note that the res_to_temp table must be strictly sorted by falling resistance
+ * values to work.
+ */
+static struct abx500_res_to_temp temp_tbl_A_thermistor[] = {
+	{-5, 53407},
+	{ 0, 48594},
+	{ 5, 43804},
+	{10, 39188},
+	{15, 34870},
+	{20, 30933},
+	{25, 27422},
+	{30, 24347},
+	{35, 21694},
+	{40, 19431},
+	{45, 17517},
+	{50, 15908},
+	{55, 14561},
+	{60, 13437},
+	{65, 12500},
+};
+static struct abx500_res_to_temp temp_tbl_B_thermistor[] = {
+	{-5, 165418},
+	{ 0, 159024},
+	{ 5, 151921},
+	{10, 144300},
+	{15, 136424},
+	{20, 128565},
+	{25, 120978},
+	{30, 113875},
+	{35, 107397},
+	{40, 101629},
+	{45,  96592},
+	{50,  92253},
+	{55,  88569},
+	{60,  85461},
+	{65,  82869},
+};
+static struct abx500_v_to_cap cap_tbl_A_thermistor[] = {
+	{4171,	100},
+	{4114,	 95},
+	{4009,	 83},
+	{3947,	 74},
+	{3907,	 67},
+	{3863,	 59},
+	{3830,	 56},
+	{3813,	 53},
+	{3791,	 46},
+	{3771,	 33},
+	{3754,	 25},
+	{3735,	 20},
+	{3717,	 17},
+	{3681,	 13},
+	{3664,	  8},
+	{3651,	  6},
+	{3635,	  5},
+	{3560,	  3},
+	{3408,    1},
+	{3247,	  0},
+};
+static struct abx500_v_to_cap cap_tbl_B_thermistor[] = {
+	{4161,	100},
+	{4124,	 98},
+	{4044,	 90},
+	{4003,	 85},
+	{3966,	 80},
+	{3933,	 75},
+	{3888,	 67},
+	{3849,	 60},
+	{3813,	 55},
+	{3787,	 47},
+	{3772,	 30},
+	{3751,	 25},
+	{3718,	 20},
+	{3681,	 16},
+	{3660,	 14},
+	{3589,	 10},
+	{3546,	  7},
+	{3495,	  4},
+	{3404,	  2},
+	{3250,	  0},
+};
+
+static struct abx500_v_to_cap cap_tbl[] = {
+	{4186,	100},
+	{4163,	 99},
+	{4114,	 95},
+	{4068,	 90},
+	{3990,	 80},
+	{3926,	 70},
+	{3898,	 65},
+	{3866,	 60},
+	{3833,	 55},
+	{3812,	 50},
+	{3787,	 40},
+	{3768,	 30},
+	{3747,	 25},
+	{3730,	 20},
+	{3705,	 15},
+	{3699,	 14},
+	{3684,	 12},
+	{3672,	  9},
+	{3657,	  7},
+	{3638,	  6},
+	{3556,	  4},
+	{3424,	  2},
+	{3317,	  1},
+	{3094,	  0},
+};
+
+/*
+ * Note that the res_to_temp table must be strictly sorted by falling
+ * resistance values to work.
+ */
+static struct abx500_res_to_temp temp_tbl[] = {
+	{-5, 214834},
+	{ 0, 162943},
+	{ 5, 124820},
+	{10,  96520},
+	{15,  75306},
+	{20,  59254},
+	{25,  47000},
+	{30,  37566},
+	{35,  30245},
+	{40,  24520},
+	{45,  20010},
+	{50,  16432},
+	{55,  13576},
+	{60,  11280},
+	{65,   9425},
+};
+
+/*
+ * Note that the batres_vs_temp table must be strictly sorted by falling
+ * temperature values to work.
+ */
+struct batres_vs_temp temp_to_batres_tbl_thermistor[] = {
+	{ 40, 120},
+	{ 30, 135},
+	{ 20, 165},
+	{ 10, 230},
+	{ 00, 325},
+	{-10, 445},
+	{-20, 595},
+};
+
+/*
+ * Note that the batres_vs_temp table must be strictly sorted by falling
+ * temperature values to work.
+ */
+struct batres_vs_temp temp_to_batres_tbl_ext_thermistor[] = {
+	{ 60, 300},
+	{ 30, 300},
+	{ 20, 300},
+	{ 10, 300},
+	{ 00, 300},
+	{-10, 300},
+	{-20, 300},
+};
+
+/* battery resistance table for LI ION 9100 battery */
+struct batres_vs_temp temp_to_batres_tbl_9100[] = {
+	{ 60, 180},
+	{ 30, 180},
+	{ 20, 180},
+	{ 10, 180},
+	{ 00, 180},
+	{-10, 180},
+	{-20, 180},
+};
+
+struct abx500_battery_type bat_type_thermistor[] = {
+[BATTERY_UNKNOWN] = {
+	/* First element always represent the UNKNOWN battery */
+	.name = POWER_SUPPLY_TECHNOLOGY_UNKNOWN,
+	.resis_high = 0,
+	.resis_low = 0,
+	.battery_resistance = 300,
+	.charge_full_design = 612,
+	.nominal_voltage = 3700,
+	.termination_vol = 4050,
+	.termination_curr = 200,
+	.recharge_vol = 3990,
+	.normal_cur_lvl = 400,
+	.normal_vol_lvl = 4100,
+	.maint_a_cur_lvl = 400,
+	.maint_a_vol_lvl = 4050,
+	.maint_a_chg_timer_h = 60,
+	.maint_b_cur_lvl = 400,
+	.maint_b_vol_lvl = 4000,
+	.maint_b_chg_timer_h = 200,
+	.low_high_cur_lvl = 300,
+	.low_high_vol_lvl = 4000,
+	.n_temp_tbl_elements = ARRAY_SIZE(temp_tbl),
+	.r_to_t_tbl = temp_tbl,
+	.n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl),
+	.v_to_cap_tbl = cap_tbl,
+	.n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
+	.batres_tbl = temp_to_batres_tbl_thermistor,
+},
+{
+	.name = POWER_SUPPLY_TECHNOLOGY_LIPO,
+	.resis_high = 53407,
+	.resis_low = 12500,
+	.battery_resistance = 300,
+	.charge_full_design = 900,
+	.nominal_voltage = 3600,
+	.termination_vol = 4150,
+	.termination_curr = 80,
+	.recharge_vol = 4130,
+	.normal_cur_lvl = 700,
+	.normal_vol_lvl = 4200,
+	.maint_a_cur_lvl = 600,
+	.maint_a_vol_lvl = 4150,
+	.maint_a_chg_timer_h = 60,
+	.maint_b_cur_lvl = 600,
+	.maint_b_vol_lvl = 4100,
+	.maint_b_chg_timer_h = 200,
+	.low_high_cur_lvl = 300,
+	.low_high_vol_lvl = 4000,
+	.n_temp_tbl_elements = ARRAY_SIZE(temp_tbl_A_thermistor),
+	.r_to_t_tbl = temp_tbl_A_thermistor,
+	.n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl_A_thermistor),
+	.v_to_cap_tbl = cap_tbl_A_thermistor,
+	.n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
+	.batres_tbl = temp_to_batres_tbl_thermistor,
+
+},
+{
+	.name = POWER_SUPPLY_TECHNOLOGY_LIPO,
+	.resis_high = 165418,
+	.resis_low = 82869,
+	.battery_resistance = 300,
+	.charge_full_design = 900,
+	.nominal_voltage = 3600,
+	.termination_vol = 4150,
+	.termination_curr = 80,
+	.recharge_vol = 4130,
+	.normal_cur_lvl = 700,
+	.normal_vol_lvl = 4200,
+	.maint_a_cur_lvl = 600,
+	.maint_a_vol_lvl = 4150,
+	.maint_a_chg_timer_h = 60,
+	.maint_b_cur_lvl = 600,
+	.maint_b_vol_lvl = 4100,
+	.maint_b_chg_timer_h = 200,
+	.low_high_cur_lvl = 300,
+	.low_high_vol_lvl = 4000,
+	.n_temp_tbl_elements = ARRAY_SIZE(temp_tbl_B_thermistor),
+	.r_to_t_tbl = temp_tbl_B_thermistor,
+	.n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl_B_thermistor),
+	.v_to_cap_tbl = cap_tbl_B_thermistor,
+	.n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
+	.batres_tbl = temp_to_batres_tbl_thermistor,
+},
+};
+
+struct abx500_battery_type bat_type_ext_thermistor[] = {
+[BATTERY_UNKNOWN] = {
+	/* First element always represent the UNKNOWN battery */
+	.name = POWER_SUPPLY_TECHNOLOGY_UNKNOWN,
+	.resis_high = 0,
+	.resis_low = 0,
+	.battery_resistance = 300,
+	.charge_full_design = 612,
+	.nominal_voltage = 3700,
+	.termination_vol = 4050,
+	.termination_curr = 200,
+	.recharge_vol = 3990,
+	.normal_cur_lvl = 400,
+	.normal_vol_lvl = 4100,
+	.maint_a_cur_lvl = 400,
+	.maint_a_vol_lvl = 4050,
+	.maint_a_chg_timer_h = 60,
+	.maint_b_cur_lvl = 400,
+	.maint_b_vol_lvl = 4000,
+	.maint_b_chg_timer_h = 200,
+	.low_high_cur_lvl = 300,
+	.low_high_vol_lvl = 4000,
+	.n_temp_tbl_elements = ARRAY_SIZE(temp_tbl),
+	.r_to_t_tbl = temp_tbl,
+	.n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl),
+	.v_to_cap_tbl = cap_tbl,
+	.n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
+	.batres_tbl = temp_to_batres_tbl_thermistor,
+},
+/*
+ * These are the batteries that doesn't have an internal NTC resistor to measure
+ * its temperature. The temperature in this case is measure with a NTC placed
+ * near the battery but on the PCB.
+ */
+{
+	.name = POWER_SUPPLY_TECHNOLOGY_LIPO,
+	.resis_high = 76000,
+	.resis_low = 53000,
+	.battery_resistance = 300,
+	.charge_full_design = 900,
+	.nominal_voltage = 3700,
+	.termination_vol = 4150,
+	.termination_curr = 100,
+	.recharge_vol = 4130,
+	.normal_cur_lvl = 700,
+	.normal_vol_lvl = 4200,
+	.maint_a_cur_lvl = 600,
+	.maint_a_vol_lvl = 4150,
+	.maint_a_chg_timer_h = 60,
+	.maint_b_cur_lvl = 600,
+	.maint_b_vol_lvl = 4100,
+	.maint_b_chg_timer_h = 200,
+	.low_high_cur_lvl = 300,
+	.low_high_vol_lvl = 4000,
+	.n_temp_tbl_elements = ARRAY_SIZE(temp_tbl),
+	.r_to_t_tbl = temp_tbl,
+	.n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl),
+	.v_to_cap_tbl = cap_tbl,
+	.n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
+	.batres_tbl = temp_to_batres_tbl_thermistor,
+},
+{
+	.name = POWER_SUPPLY_TECHNOLOGY_LION,
+	.resis_high = 30000,
+	.resis_low = 10000,
+	.battery_resistance = 300,
+	.charge_full_design = 950,
+	.nominal_voltage = 3700,
+	.termination_vol = 4150,
+	.termination_curr = 100,
+	.recharge_vol = 4130,
+	.normal_cur_lvl = 700,
+	.normal_vol_lvl = 4200,
+	.maint_a_cur_lvl = 600,
+	.maint_a_vol_lvl = 4150,
+	.maint_a_chg_timer_h = 60,
+	.maint_b_cur_lvl = 600,
+	.maint_b_vol_lvl = 4100,
+	.maint_b_chg_timer_h = 200,
+	.low_high_cur_lvl = 300,
+	.low_high_vol_lvl = 4000,
+	.n_temp_tbl_elements = ARRAY_SIZE(temp_tbl),
+	.r_to_t_tbl = temp_tbl,
+	.n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl),
+	.v_to_cap_tbl = cap_tbl,
+	.n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
+	.batres_tbl = temp_to_batres_tbl_thermistor,
+},
+{
+	.name = POWER_SUPPLY_TECHNOLOGY_LION,
+	.resis_high = 95000,
+	.resis_low = 76001,
+	.battery_resistance = 300,
+	.charge_full_design = 950,
+	.nominal_voltage = 3700,
+	.termination_vol = 4150,
+	.termination_curr = 100,
+	.recharge_vol = 4130,
+	.normal_cur_lvl = 700,
+	.normal_vol_lvl = 4200,
+	.maint_a_cur_lvl = 600,
+	.maint_a_vol_lvl = 4150,
+	.maint_a_chg_timer_h = 60,
+	.maint_b_cur_lvl = 600,
+	.maint_b_vol_lvl = 4100,
+	.maint_b_chg_timer_h = 200,
+	.low_high_cur_lvl = 300,
+	.low_high_vol_lvl = 4000,
+	.n_temp_tbl_elements = ARRAY_SIZE(temp_tbl),
+	.r_to_t_tbl = temp_tbl,
+	.n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl),
+	.v_to_cap_tbl = cap_tbl,
+	.n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
+	.batres_tbl = temp_to_batres_tbl_thermistor,
+},
+};
+
+static const struct abx500_bm_capacity_levels cap_levels = {
+	.critical	= 2,
+	.low		= 10,
+	.normal		= 70,
+	.high		= 95,
+	.full		= 100,
+};
+
+static const struct abx500_fg_parameters fg = {
+	.recovery_sleep_timer = 10,
+	.recovery_total_time = 100,
+	.init_timer = 1,
+	.init_discard_time = 5,
+	.init_total_time = 40,
+	.high_curr_time = 60,
+	.accu_charging = 30,
+	.accu_high_curr = 30,
+	.high_curr_threshold = 50,
+	.lowbat_threshold = 3100,
+	.battok_falling_th_sel0 = 2860,
+	.battok_raising_th_sel1 = 2860,
+	.user_cap_limit = 15,
+	.maint_thres = 97,
+};
+
+static const struct abx500_maxim_parameters maxi_params = {
+	.ena_maxi = true,
+	.chg_curr = 910,
+	.wait_cycles = 10,
+	.charger_curr_step = 100,
+};
+
+static const struct abx500_bm_charger_parameters chg = {
+	.usb_volt_max		= 5500,
+	.usb_curr_max		= 1500,
+	.ac_volt_max		= 7500,
+	.ac_curr_max		= 1500,
+};
+
+struct abx500_bm_data ab8500_bm_data = {
+	.temp_under		= 3,
+	.temp_low		= 8,
+	.temp_high		= 43,
+	.temp_over		= 48,
+	.main_safety_tmr_h	= 4,
+	.temp_interval_chg	= 20,
+	.temp_interval_nochg	= 120,
+	.usb_safety_tmr_h	= 4,
+	.bkup_bat_v		= BUP_VCH_SEL_2P6V,
+	.bkup_bat_i		= BUP_ICH_SEL_150UA,
+	.no_maintenance		= false,
+	.adc_therm		= ABx500_ADC_THERM_BATCTRL,
+	.chg_unknown_bat	= false,
+	.enable_overshoot	= false,
+	.fg_res			= 100,
+	.cap_levels		= &cap_levels,
+	.bat_type		= bat_type_thermistor,
+	.n_btypes		= 3,
+	.batt_id		= 0,
+	.interval_charging	= 5,
+	.interval_not_charging	= 120,
+	.temp_hysteresis	= 3,
+	.gnd_lift_resistance	= 34,
+	.maxi			= &maxi_params,
+	.chg_params		= &chg,
+	.fg_params		= &fg,
+};
+
+int __devinit
+bmdevs_of_probe(struct device *dev,
+		struct device_node *np,
+		struct abx500_bm_data **battery)
+{
+	struct	abx500_battery_type *btype;
+	struct  device_node *np_bat_supply;
+	struct	abx500_bm_data *bat;
+	const char *btech;
+	int i, thermistor;
+
+	*battery = &ab8500_bm_data;
+
+	/* get phandle to 'battery-info' node */
+	np_bat_supply = of_parse_phandle(np, "battery", 0);
+	if (!np_bat_supply) {
+		dev_err(dev, "missing property battery\n");
+		return -EINVAL;
+	}
+	if (of_property_read_bool(np_bat_supply,
+			"thermistor-on-batctrl"))
+		thermistor = NTC_INTERNAL;
+	else
+		thermistor = NTC_EXTERNAL;
+
+	bat = *battery;
+	if (thermistor == NTC_EXTERNAL) {
+		bat->n_btypes  = 4;
+		bat->bat_type  = bat_type_ext_thermistor;
+		bat->adc_therm = ABx500_ADC_THERM_BATTEMP;
+	}
+	btech = of_get_property(np_bat_supply,
+		"stericsson,battery-type", NULL);
+	if (!btech) {
+		dev_warn(dev, "missing property battery-name/type\n");
+		return -EINVAL;
+	}
+	if (strncmp(btech, "LION", 4) == 0) {
+		bat->no_maintenance  = true;
+		bat->chg_unknown_bat = true;
+		bat->bat_type[BATTERY_UNKNOWN].charge_full_design = 2600;
+		bat->bat_type[BATTERY_UNKNOWN].termination_vol    = 4150;
+		bat->bat_type[BATTERY_UNKNOWN].recharge_vol	  = 4130;
+		bat->bat_type[BATTERY_UNKNOWN].normal_cur_lvl	  = 520;
+		bat->bat_type[BATTERY_UNKNOWN].normal_vol_lvl	  = 4200;
+	}
+	/* select the battery resolution table */
+	for (i = 0; i < bat->n_btypes; ++i) {
+		btype = (bat->bat_type + i);
+		if (thermistor == NTC_EXTERNAL) {
+			btype->batres_tbl =
+				temp_to_batres_tbl_ext_thermistor;
+		} else if (strncmp(btech, "LION", 4) == 0) {
+			btype->batres_tbl =
+				temp_to_batres_tbl_9100;
+		} else {
+			btype->batres_tbl =
+				temp_to_batres_tbl_thermistor;
+		}
+	}
+	of_node_put(np_bat_supply);
+	return 0;
+}
diff --git a/drivers/power/ab8500_btemp.c b/drivers/power/ab8500_btemp.c
index e3b6395..abc2abc 100644
--- a/drivers/power/ab8500_btemp.c
+++ b/drivers/power/ab8500_btemp.c
@@ -93,7 +93,7 @@ struct ab8500_btemp {
 	struct ab8500 *parent;
 	struct ab8500_gpadc *gpadc;
 	struct ab8500_fg *fg;
-	struct abx500_btemp_platform_data *pdata;
+	struct abx500_bmdevs_plat_data *pdata;
 	struct abx500_bm_data *bat;
 	struct power_supply btemp_psy;
 	struct ab8500_btemp_events events;
@@ -962,10 +962,10 @@ static int __devexit ab8500_btemp_remove(struct platform_device *pdev)
 
 static int __devinit ab8500_btemp_probe(struct platform_device *pdev)
 {
+	struct abx500_bmdevs_plat_data *plat_data = pdev->dev.platform_data;
+	struct ab8500_btemp *di;
 	int irq, i, ret = 0;
 	u8 val;
-	struct abx500_bm_plat_data *plat_data = pdev->dev.platform_data;
-	struct ab8500_btemp *di;
 
 	if (!plat_data) {
 		dev_err(&pdev->dev, "No platform data\n");
@@ -982,21 +982,13 @@ static int __devinit ab8500_btemp_probe(struct platform_device *pdev)
 	di->gpadc = ab8500_gpadc_get("ab8500-gpadc.0");
 
 	/* get btemp specific platform data */
-	di->pdata = plat_data->btemp;
+	di->pdata = plat_data;
 	if (!di->pdata) {
 		dev_err(di->dev, "no btemp platform data supplied\n");
 		ret = -EINVAL;
 		goto free_device_info;
 	}
 
-	/* get battery specific platform data */
-	di->bat = plat_data->battery;
-	if (!di->bat) {
-		dev_err(di->dev, "no battery platform data supplied\n");
-		ret = -EINVAL;
-		goto free_device_info;
-	}
-
 	/* BTEMP supply */
 	di->btemp_psy.name = "ab8500_btemp";
 	di->btemp_psy.type = POWER_SUPPLY_TYPE_BATTERY;
diff --git a/drivers/power/ab8500_charger.c b/drivers/power/ab8500_charger.c
index 26ff759..723edb4 100644
--- a/drivers/power/ab8500_charger.c
+++ b/drivers/power/ab8500_charger.c
@@ -220,7 +220,7 @@ struct ab8500_charger {
 	bool autopower;
 	struct ab8500 *parent;
 	struct ab8500_gpadc *gpadc;
-	struct abx500_charger_platform_data *pdata;
+	struct abx500_bmdevs_plat_data *pdata;
 	struct abx500_bm_data *bat;
 	struct ab8500_charger_event_flags flags;
 	struct ab8500_charger_usb_state usb_state;
@@ -2533,9 +2533,9 @@ static int __devexit ab8500_charger_remove(struct platform_device *pdev)
 
 static int __devinit ab8500_charger_probe(struct platform_device *pdev)
 {
-	int irq, i, charger_status, ret = 0;
-	struct abx500_bm_plat_data *plat_data = pdev->dev.platform_data;
+	struct abx500_bmdevs_plat_data *plat_data = pdev->dev.platform_data;
 	struct ab8500_charger *di;
+	int irq, i, charger_status, ret = 0;
 
 	if (!plat_data) {
 		dev_err(&pdev->dev, "No platform data\n");
@@ -2555,21 +2555,13 @@ static int __devinit ab8500_charger_probe(struct platform_device *pdev)
 	spin_lock_init(&di->usb_state.usb_lock);
 
 	/* get charger specific platform data */
-	di->pdata = plat_data->charger;
+	di->pdata = plat_data;
 	if (!di->pdata) {
 		dev_err(di->dev, "no charger platform data supplied\n");
 		ret = -EINVAL;
 		goto free_device_info;
 	}
 
-	/* get battery specific platform data */
-	di->bat = plat_data->battery;
-	if (!di->bat) {
-		dev_err(di->dev, "no battery platform data supplied\n");
-		ret = -EINVAL;
-		goto free_device_info;
-	}
-
 	di->autopower = false;
 
 	/* AC supply */
diff --git a/drivers/power/ab8500_fg.c b/drivers/power/ab8500_fg.c
index 2db8cc2..20ac3b8 100644
--- a/drivers/power/ab8500_fg.c
+++ b/drivers/power/ab8500_fg.c
@@ -22,15 +22,16 @@
 #include <linux/platform_device.h>
 #include <linux/power_supply.h>
 #include <linux/kobject.h>
-#include <linux/mfd/abx500/ab8500.h>
-#include <linux/mfd/abx500.h>
 #include <linux/slab.h>
-#include <linux/mfd/abx500/ab8500-bm.h>
 #include <linux/delay.h>
-#include <linux/mfd/abx500/ab8500-gpadc.h>
-#include <linux/mfd/abx500.h>
 #include <linux/time.h>
+#include <linux/of.h>
 #include <linux/completion.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/abx500.h>
+#include <linux/mfd/abx500/ab8500.h>
+#include <linux/mfd/abx500/ab8500-bm.h>
+#include <linux/mfd/abx500/ab8500-gpadc.h>
 
 #define MILLI_TO_MICRO			1000
 #define FG_LSB_IN_MA			1627
@@ -172,7 +173,6 @@ struct inst_curr_result_list {
  * @avg_cap:		Average capacity filter
  * @parent:		Pointer to the struct ab8500
  * @gpadc:		Pointer to the struct gpadc
- * @pdata:		Pointer to the abx500_fg platform data
  * @bat:		Pointer to the abx500_bm platform data
  * @fg_psy:		Structure that holds the FG specific battery properties
  * @fg_wq:		Work queue for running the FG algorithm
@@ -212,7 +212,6 @@ struct ab8500_fg {
 	struct ab8500_fg_avg_cap avg_cap;
 	struct ab8500 *parent;
 	struct ab8500_gpadc *gpadc;
-	struct abx500_fg_platform_data *pdata;
 	struct abx500_bm_data *bat;
 	struct power_supply fg_psy;
 	struct workqueue_struct *fg_wq;
@@ -2429,7 +2428,6 @@ static int __devexit ab8500_fg_remove(struct platform_device *pdev)
 	flush_scheduled_work();
 	power_supply_unregister(&di->fg_psy);
 	platform_set_drvdata(pdev, NULL);
-	kfree(di);
 	return ret;
 }
 
@@ -2442,21 +2440,39 @@ static struct ab8500_fg_interrupts ab8500_fg_irq[] = {
 	{"CCEOC", ab8500_fg_cc_data_end_handler},
 };
 
+static char *supply_interface[] = {
+	"ab8500_chargalg",
+	"ab8500_usb",
+};
+
 static int __devinit ab8500_fg_probe(struct platform_device *pdev)
 {
+	struct device_node *np = pdev->dev.of_node;
+	struct ab8500_fg *di;
 	int i, irq;
 	int ret = 0;
-	struct abx500_bm_plat_data *plat_data = pdev->dev.platform_data;
-	struct ab8500_fg *di;
-
-	if (!plat_data) {
-		dev_err(&pdev->dev, "No platform data\n");
-		return -EINVAL;
-	}
 
-	di = kzalloc(sizeof(*di), GFP_KERNEL);
-	if (!di)
+	di = devm_kzalloc(&pdev->dev, sizeof(*di), GFP_KERNEL);
+	if (!di) {
+		dev_err(&pdev->dev, "%s no mem for ab8500_fg\n", __func__);
 		return -ENOMEM;
+	}
+	di->bat = pdev->mfd_cell->platform_data;
+	if (!di->bat) {
+		if (np) {
+			ret = bmdevs_of_probe(&pdev->dev, np, &di->bat);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"failed to get battery information\n");
+				return ret;
+			}
+		} else {
+			dev_err(&pdev->dev, "missing dt node for ab8500_fg\n");
+			return -EINVAL;
+		}
+	} else {
+		dev_info(&pdev->dev, "falling back to legacy platform data\n");
+	}
 
 	mutex_init(&di->cc_lock);
 
@@ -2465,29 +2481,13 @@ static int __devinit ab8500_fg_probe(struct platform_device *pdev)
 	di->parent = dev_get_drvdata(pdev->dev.parent);
 	di->gpadc = ab8500_gpadc_get("ab8500-gpadc.0");
 
-	/* get fg specific platform data */
-	di->pdata = plat_data->fg;
-	if (!di->pdata) {
-		dev_err(di->dev, "no fg platform data supplied\n");
-		ret = -EINVAL;
-		goto free_device_info;
-	}
-
-	/* get battery specific platform data */
-	di->bat = plat_data->battery;
-	if (!di->bat) {
-		dev_err(di->dev, "no battery platform data supplied\n");
-		ret = -EINVAL;
-		goto free_device_info;
-	}
-
 	di->fg_psy.name = "ab8500_fg";
 	di->fg_psy.type = POWER_SUPPLY_TYPE_BATTERY;
 	di->fg_psy.properties = ab8500_fg_props;
 	di->fg_psy.num_properties = ARRAY_SIZE(ab8500_fg_props);
 	di->fg_psy.get_property = ab8500_fg_get_property;
-	di->fg_psy.supplied_to = di->pdata->supplied_to;
-	di->fg_psy.num_supplicants = di->pdata->num_supplicants;
+	di->fg_psy.supplied_to = supply_interface;
+	di->fg_psy.num_supplicants = ARRAY_SIZE(supply_interface),
 	di->fg_psy.external_power_changed = ab8500_fg_external_power_changed;
 
 	di->bat_cap.max_mah_design = MILLI_TO_MICRO *
@@ -2506,8 +2506,7 @@ static int __devinit ab8500_fg_probe(struct platform_device *pdev)
 	di->fg_wq = create_singlethread_workqueue("ab8500_fg_wq");
 	if (di->fg_wq == NULL) {
 		dev_err(di->dev, "failed to create work queue\n");
-		ret = -ENOMEM;
-		goto free_device_info;
+		return -ENOMEM;
 	}
 
 	/* Init work for running the fg algorithm instantly */
@@ -2606,12 +2605,15 @@ free_irq:
 	}
 free_inst_curr_wq:
 	destroy_workqueue(di->fg_wq);
-free_device_info:
-	kfree(di);
 
 	return ret;
 }
 
+static const struct of_device_id ab8500_fg_match[] = {
+	{ .compatible = "stericsson,ab8500-fg", },
+	{ },
+};
+
 static struct platform_driver ab8500_fg_driver = {
 	.probe = ab8500_fg_probe,
 	.remove = __devexit_p(ab8500_fg_remove),
@@ -2620,6 +2622,7 @@ static struct platform_driver ab8500_fg_driver = {
 	.driver = {
 		.name = "ab8500-fg",
 		.owner = THIS_MODULE,
+		.of_match_table = ab8500_fg_match,
 	},
 };
 
diff --git a/drivers/power/abx500_chargalg.c b/drivers/power/abx500_chargalg.c
index 4d30280..94bf69b 100644
--- a/drivers/power/abx500_chargalg.c
+++ b/drivers/power/abx500_chargalg.c
@@ -231,7 +231,7 @@ struct abx500_chargalg {
 	struct abx500_chargalg_charger_info chg_info;
 	struct abx500_chargalg_battery_data batt_data;
 	struct abx500_chargalg_suspension_status susp_status;
-	struct abx500_chargalg_platform_data *pdata;
+	struct abx500_bmdevs_plat_data *pdata;
 	struct abx500_bm_data *bat;
 	struct power_supply chargalg_psy;
 	struct ux500_charger *ac_chg;
@@ -1802,7 +1802,7 @@ static int __devexit abx500_chargalg_remove(struct platform_device *pdev)
 
 static int __devinit abx500_chargalg_probe(struct platform_device *pdev)
 {
-	struct abx500_bm_plat_data *plat_data;
+	struct abx500_bmdevs_plat_data *plat_data;
 	int ret = 0;
 
 	struct abx500_chargalg *di =
@@ -1814,8 +1814,7 @@ static int __devinit abx500_chargalg_probe(struct platform_device *pdev)
 	di->dev = &pdev->dev;
 
 	plat_data = pdev->dev.platform_data;
-	di->pdata = plat_data->chargalg;
-	di->bat = plat_data->battery;
+	di->pdata = plat_data;
 
 	/* chargalg supply */
 	di->chargalg_psy.name = "abx500_chargalg";
diff --git a/include/linux/mfd/abx500.h b/include/linux/mfd/abx500.h
index 5d5298d..33f2c58 100644
--- a/include/linux/mfd/abx500.h
+++ b/include/linux/mfd/abx500.h
@@ -267,39 +267,27 @@ struct abx500_bm_data {
 	int gnd_lift_resistance;
 	const struct abx500_maxim_parameters *maxi;
 	const struct abx500_bm_capacity_levels *cap_levels;
-	const struct abx500_battery_type *bat_type;
+	struct abx500_battery_type *bat_type;
 	const struct abx500_bm_charger_parameters *chg_params;
 	const struct abx500_fg_parameters *fg_params;
 };
 
-struct abx500_chargalg_platform_data {
-	char **supplied_to;
-	size_t num_supplicants;
-};
-
-struct abx500_charger_platform_data {
-	char **supplied_to;
-	size_t num_supplicants;
-	bool autopower_cfg;
-};
+extern struct abx500_bm_data ab8500_bm_data;
 
-struct abx500_btemp_platform_data {
-	char **supplied_to;
-	size_t num_supplicants;
+struct abx500_bmdevs_plat_data {
+	char	**supplied_to;
+	size_t	num_supplicants;
+	bool	autopower_cfg;
 };
 
-struct abx500_fg_platform_data {
-	char **supplied_to;
-	size_t num_supplicants;
+enum {
+	NTC_EXTERNAL = 0,
+	NTC_INTERNAL,
 };
 
-struct abx500_bm_plat_data {
-	struct abx500_bm_data *battery;
-	struct abx500_charger_platform_data *charger;
-	struct abx500_btemp_platform_data *btemp;
-	struct abx500_fg_platform_data *fg;
-	struct abx500_chargalg_platform_data *chargalg;
-};
+int bmdevs_of_probe(struct device *dev,
+		struct device_node *np,
+		struct abx500_bm_data **battery);
 
 int abx500_set_register_interruptible(struct device *dev, u8 bank, u8 reg,
 	u8 value);
-- 
1.7.10.4

[PATCH 2/4] mfd: ab8500: add devicetree support for btemp

[Rajanikanth H.V]

From: "Rajanikanth H.V" <rajanikanth.hv@stericsson.com>

This patch adds device tree support for
battery-temperature-monitor driver

Signed-off-by: Rajanikanth H.V <rajanikanth.hv@linaro.org>
---
 Documentation/devicetree/bindings/mfd/ab8500.txt   |    6 ++
 .../bindings/power_supply/ab8500/btemp.txt         |   16 +++++
 arch/arm/boot/dts/dbx5x0.dtsi                      |    5 ++
 drivers/mfd/ab8500-core.c                          |    5 ++
 drivers/power/Kconfig                              |    6 --
 drivers/power/ab8500_bmdata.c                      |    4 +-
 drivers/power/ab8500_btemp.c                       |   65 ++++++++++++--------
 7 files changed, 73 insertions(+), 34 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/power_supply/ab8500/btemp.txt

diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt
index 6ca8d81..f2ee0e7 100644
--- a/Documentation/devicetree/bindings/mfd/ab8500.txt
+++ b/Documentation/devicetree/bindings/mfd/ab8500.txt
@@ -30,6 +30,12 @@ ab8500-fg                : 			: vddadc       : Fuel Gauge
 			 : LOW_BAT_F		:	       : LOW threshold battery voltage
 			 : CC_INT_CALIB		:	       : Coulomb Counter Internal Calibration
 			 : CCEOC		:	       : Coulomb Counter End of Conversion
+ab8500-btemp		 :			: vtvout       : Battery Temperature
+			 : BAT_CTRL_INDB        :              : Battery Removal Indicator
+			 : BTEMP_LOW            :              : Btemp < BtempLow, if battery temperature is lower than -10°C
+			 : BTEMP_LOW_MEDIUM     :              : BtempLow < Btemp < BtempMedium,if battery temperature is between -10 and 0°C
+			 : BTEMP_MEDIUM_HIGH    :	       : BtempMedium < Btemp < BtempHigh,if battery temperature is between 0°C and“MaxTemp
+			 : BTEMP_HIGH           :              : Btemp > BtempHigh, if battery temperature is higher than “MaxTemp
 ab8500-gpadc             : HW_CONV_END          : vddadc       : Analogue to Digital Converter
                            SW_CONV_END          :              :
 ab8500-gpio              :                      :              : GPIO Controller
diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/btemp.txt b/Documentation/devicetree/bindings/power_supply/ab8500/btemp.txt
new file mode 100644
index 0000000..0ba1bcc
--- /dev/null
+++ b/Documentation/devicetree/bindings/power_supply/ab8500/btemp.txt
@@ -0,0 +1,16 @@
+=== AB8500 Battery Temperature Monitor Driver ===
+
+The properties below describes the node for btemp driver.
+
+Required Properties:
+- compatible = Shall be: "stericsson,ab8500-btemp"
+- battery = Shall be battery specific information
+
+	Example:
+	ab8500_btemp {
+		compatible = "stericsson,ab8500-btemp";
+		battery	   = <&ab8500_battery>;
+	};
+
+For information on battery specific node, Ref:
+Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
index 155cf53..3f1d899 100644
--- a/arch/arm/boot/dts/dbx5x0.dtsi
+++ b/arch/arm/boot/dts/dbx5x0.dtsi
@@ -357,6 +357,11 @@
 					thermistor-on-batctrl;
 				};
 
+				ab8500-btemp {
+					compatible = "stericsson,ab8500-btemp";
+					battery	   = <&ab8500_battery>;
+				};
+
 				ab8500-fg {
 					compatible = "stericsson,ab8500-fg";
 					battery	   = <&ab8500_battery>;
diff --git a/drivers/mfd/ab8500-core.c b/drivers/mfd/ab8500-core.c
index 7c3017b..94d45be 100644
--- a/drivers/mfd/ab8500-core.c
+++ b/drivers/mfd/ab8500-core.c
@@ -1046,8 +1046,13 @@ static struct mfd_cell __devinitdata ab8500_bm_devs[] = {
 	},
 	{
 		.name = "ab8500-btemp",
+		.of_compatible = "stericsson,ab8500-btemp",
 		.num_resources = ARRAY_SIZE(ab8500_btemp_resources),
 		.resources = ab8500_btemp_resources,
+#ifndef CONFIG_OF
+		.platform_data = &ab8500_bm_data,
+		.pdata_size = sizeof(ab8500_bm_data),
+#endif
 	},
 	{
 		.name = "ab8500-fg",
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index 49a8939..027f74e 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -329,12 +329,6 @@ config AB8500_BM
 	help
 	  Say Y to include support for AB8500 battery management.
 
-config AB8500_BATTERY_THERM_ON_BATCTRL
-	bool "Thermistor connected on BATCTRL ADC"
-	depends on AB8500_BM
-	help
-	  Say Y to enable battery temperature measurements using
-	  thermistor connected on BATCTRL ADC.
 endif # POWER_SUPPLY
 
 source "drivers/power/avs/Kconfig"
diff --git a/drivers/power/ab8500_bmdata.c b/drivers/power/ab8500_bmdata.c
index 0366270..ff8f055 100644
--- a/drivers/power/ab8500_bmdata.c
+++ b/drivers/power/ab8500_bmdata.c
@@ -29,7 +29,7 @@ static struct abx500_res_to_temp temp_tbl_A_thermistor[] = {
 	{65, 12500},
 };
 static struct abx500_res_to_temp temp_tbl_B_thermistor[] = {
-	{-5, 165418},
+	{-5, 200000},
 	{ 0, 159024},
 	{ 5, 151921},
 	{10, 144300},
@@ -237,7 +237,7 @@ struct abx500_battery_type bat_type_thermistor[] = {
 },
 {
 	.name = POWER_SUPPLY_TECHNOLOGY_LIPO,
-	.resis_high = 165418,
+	.resis_high = 200000,
 	.resis_low = 82869,
 	.battery_resistance = 300,
 	.charge_full_design = 900,
diff --git a/drivers/power/ab8500_btemp.c b/drivers/power/ab8500_btemp.c
index abc2abc..b5dfc77 100644
--- a/drivers/power/ab8500_btemp.c
+++ b/drivers/power/ab8500_btemp.c
@@ -20,11 +20,13 @@
 #include <linux/power_supply.h>
 #include <linux/completion.h>
 #include <linux/workqueue.h>
-#include <linux/mfd/abx500/ab8500.h>
+#include <linux/jiffies.h>
+#include <linux/of.h>
+#include <linux/mfd/core.h>
 #include <linux/mfd/abx500.h>
+#include <linux/mfd/abx500/ab8500.h>
 #include <linux/mfd/abx500/ab8500-bm.h>
 #include <linux/mfd/abx500/ab8500-gpadc.h>
-#include <linux/jiffies.h>
 
 #define VTVOUT_V			1800
 
@@ -76,7 +78,6 @@ struct ab8500_btemp_ranges {
  * @parent:		Pointer to the struct ab8500
  * @gpadc:		Pointer to the struct gpadc
  * @fg:			Pointer to the struct fg
- * @pdata:		Pointer to the abx500_btemp platform data
  * @bat:		Pointer to the abx500_bm platform data
  * @btemp_psy:		Structure for BTEMP specific battery properties
  * @events:		Structure for information about events triggered
@@ -93,7 +94,6 @@ struct ab8500_btemp {
 	struct ab8500 *parent;
 	struct ab8500_gpadc *gpadc;
 	struct ab8500_fg *fg;
-	struct abx500_bmdevs_plat_data *pdata;
 	struct abx500_bm_data *bat;
 	struct power_supply btemp_psy;
 	struct ab8500_btemp_events events;
@@ -955,48 +955,58 @@ static int __devexit ab8500_btemp_remove(struct platform_device *pdev)
 	flush_scheduled_work();
 	power_supply_unregister(&di->btemp_psy);
 	platform_set_drvdata(pdev, NULL);
-	kfree(di);
 
 	return 0;
 }
 
+static char *supply_interface[] = {
+	"ab8500_chargalg",
+	"ab8500_fg",
+};
+
 static int __devinit ab8500_btemp_probe(struct platform_device *pdev)
 {
-	struct abx500_bmdevs_plat_data *plat_data = pdev->dev.platform_data;
+	struct device_node *np = pdev->dev.of_node;
 	struct ab8500_btemp *di;
 	int irq, i, ret = 0;
 	u8 val;
 
-	if (!plat_data) {
-		dev_err(&pdev->dev, "No platform data\n");
-		return -EINVAL;
+	di = devm_kzalloc(&pdev->dev, sizeof(*di), GFP_KERNEL);
+	if (!di) {
+		dev_err(&pdev->dev, "%s no mem for ab8500_btemp\n", __func__);
+		return -ENOMEM;
 	}
 
-	di = kzalloc(sizeof(*di), GFP_KERNEL);
-	if (!di)
-		return -ENOMEM;
+	di->bat = pdev->mfd_cell->platform_data;
+	if (!di->bat) {
+		if (np) {
+			ret = bmdevs_of_probe(&pdev->dev, np, &di->bat);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"failed to get battery information\n");
+				return ret;
+			}
+		} else {
+			dev_err(&pdev->dev, "missing dt node for ab8500_btemp\n");
+			return -EINVAL;
+		}
+	} else {
+		dev_info(&pdev->dev, "falling back to legacy platform data\n");
+	}
 
 	/* get parent data */
 	di->dev = &pdev->dev;
 	di->parent = dev_get_drvdata(pdev->dev.parent);
 	di->gpadc = ab8500_gpadc_get("ab8500-gpadc.0");
 
-	/* get btemp specific platform data */
-	di->pdata = plat_data;
-	if (!di->pdata) {
-		dev_err(di->dev, "no btemp platform data supplied\n");
-		ret = -EINVAL;
-		goto free_device_info;
-	}
-
 	/* BTEMP supply */
 	di->btemp_psy.name = "ab8500_btemp";
 	di->btemp_psy.type = POWER_SUPPLY_TYPE_BATTERY;
 	di->btemp_psy.properties = ab8500_btemp_props;
 	di->btemp_psy.num_properties = ARRAY_SIZE(ab8500_btemp_props);
 	di->btemp_psy.get_property = ab8500_btemp_get_property;
-	di->btemp_psy.supplied_to = di->pdata->supplied_to;
-	di->btemp_psy.num_supplicants = di->pdata->num_supplicants;
+	di->btemp_psy.supplied_to = supply_interface;
+	di->btemp_psy.num_supplicants = ARRAY_SIZE(supply_interface);
 	di->btemp_psy.external_power_changed =
 		ab8500_btemp_external_power_changed;
 
@@ -1006,8 +1016,7 @@ static int __devinit ab8500_btemp_probe(struct platform_device *pdev)
 		create_singlethread_workqueue("ab8500_btemp_wq");
 	if (di->btemp_wq == NULL) {
 		dev_err(di->dev, "failed to create work queue\n");
-		ret = -ENOMEM;
-		goto free_device_info;
+		return -ENOMEM;
 	}
 
 	/* Init work for measuring temperature periodically */
@@ -1085,12 +1094,15 @@ free_irq:
 	}
 free_btemp_wq:
 	destroy_workqueue(di->btemp_wq);
-free_device_info:
-	kfree(di);
 
 	return ret;
 }
 
+static const struct of_device_id ab8500_btemp_match[] = {
+	{ .compatible = "stericsson,ab8500-btemp", },
+	{ },
+};
+
 static struct platform_driver ab8500_btemp_driver = {
 	.probe = ab8500_btemp_probe,
 	.remove = __devexit_p(ab8500_btemp_remove),
@@ -1099,6 +1111,7 @@ static struct platform_driver ab8500_btemp_driver = {
 	.driver = {
 		.name = "ab8500-btemp",
 		.owner = THIS_MODULE,
+		.of_match_table = ab8500_btemp_match,
 	},
 };
 
-- 
1.7.10.4

[PATCH 3/4] mfd: ab8500: add devicetree support for charger

[Rajanikanth H.V]

From: "Rajanikanth H.V" <rajanikanth.hv@stericsson.com>

This patch adds device tree support for ab8500-charger
driver

Signed-off-by: Rajanikanth H.V <rajanikanth.hv@linaro.org>
---
 Documentation/devicetree/bindings/mfd/ab8500.txt   |   14 ++++
 .../bindings/power_supply/ab8500/charger.txt       |   25 +++++++
 arch/arm/boot/dts/dbx5x0.dtsi                      |    6 ++
 drivers/mfd/ab8500-core.c                          |    5 ++
 drivers/power/ab8500_charger.c                     |   73 ++++++++++++--------
 5 files changed, 96 insertions(+), 27 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/power_supply/ab8500/charger.txt

diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt
index f2ee0e7..13b707b 100644
--- a/Documentation/devicetree/bindings/mfd/ab8500.txt
+++ b/Documentation/devicetree/bindings/mfd/ab8500.txt
@@ -36,6 +36,20 @@ ab8500-btemp		 :			: vtvout       : Battery Temperature
 			 : BTEMP_LOW_MEDIUM     :              : BtempLow < Btemp < BtempMedium,if battery temperature is between -10 and 0°C
 			 : BTEMP_MEDIUM_HIGH    :	       : BtempMedium < Btemp < BtempHigh,if battery temperature is between 0°C and“MaxTemp
 			 : BTEMP_HIGH           :              : Btemp > BtempHigh, if battery temperature is higher than “MaxTemp
+ab8500-charger		 :			: vddadc       : Charger interface
+			 : MAIN_CH_UNPLUG_DET	:	       : main charger unplug detection management (not in 8505)
+			 : MAIN_CHARGE_PLUG_DET	:	       : main charger plug detection management (not in 8505)
+			 : MAIN_EXT_CH_NOT_OK	:	       : main charger not OK
+			 : MAIN_CH_TH_PROT_R	:	       : Die temp is above main charger
+			 : MAIN_CH_TH_PROT_F	:	       : Die temp is below main charger
+			 : VBUS_DET_F		:	       : VBUS falling detected
+			 : VBUS_DET_R		:	       : VBUS rising detected
+			 : USB_LINK_STATUS	:	       : USB link status has changed
+			 : USB_CH_TH_PROT_R	:	       : Die temp is above usb charger
+			 : USB_CH_TH_PROT_F	:	       : Die temp is below usb charger
+			 : USB_CHARGER_NOT_OKR	:	       : allowed USB charger not ok detection
+			 : VBUS_OVV		:	       : Overvoltage on Vbus ball detected (USB charge is stopped)
+			 : CH_WD_EXP		:	       : Charger watchdog detected
 ab8500-gpadc             : HW_CONV_END          : vddadc       : Analogue to Digital Converter
                            SW_CONV_END          :              :
 ab8500-gpio              :                      :              : GPIO Controller
diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/charger.txt b/Documentation/devicetree/bindings/power_supply/ab8500/charger.txt
new file mode 100644
index 0000000..6bdbb08
--- /dev/null
+++ b/Documentation/devicetree/bindings/power_supply/ab8500/charger.txt
@@ -0,0 +1,25 @@
+=== AB8500 Charger Driver ===
+
+Required Properties:
+- compatible = Shall be "stericsson,ab8500-charger"
+- battery = Shall be battery specific information
+	Example:
+	ab8500_charger {
+		compatible = "stericsson,ab8500-charger";
+		battery	   = <&ab8500_battery>;
+	};
+
+- vddadc-supply: Supply for USB and Main charger
+	Example:
+	ab8500-charger {
+		vddadc-supply	= <&ab8500_ldo_tvout_reg>;
+	}
+- autopower_cfg:
+	Boolean value depicting the presence of 'automatic poweron after powerloss'
+	Example:
+	ab8500-charger {
+		autopower_cfg;
+	};
+
+For information on battery specific node, Ref:
+Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
index 3f1d899..7e9c01a 100644
--- a/arch/arm/boot/dts/dbx5x0.dtsi
+++ b/arch/arm/boot/dts/dbx5x0.dtsi
@@ -357,6 +357,12 @@
 					thermistor-on-batctrl;
 				};
 
+				ab8500-charger {
+					compatible	= "stericsson,ab8500-charger";
+					battery		= <&ab8500_battery>;
+					vddadc-supply	= <&ab8500_ldo_tvout_reg>;
+				};
+
 				ab8500-btemp {
 					compatible = "stericsson,ab8500-btemp";
 					battery	   = <&ab8500_battery>;
diff --git a/drivers/mfd/ab8500-core.c b/drivers/mfd/ab8500-core.c
index 94d45be..c7a120b 100644
--- a/drivers/mfd/ab8500-core.c
+++ b/drivers/mfd/ab8500-core.c
@@ -1041,8 +1041,13 @@ static struct mfd_cell __devinitdata abx500_common_devs[] = {
 static struct mfd_cell __devinitdata ab8500_bm_devs[] = {
 	{
 		.name = "ab8500-charger",
+		.of_compatible = "stericsson,ab8500-charger",
 		.num_resources = ARRAY_SIZE(ab8500_charger_resources),
 		.resources = ab8500_charger_resources,
+#ifndef CONFIG_OF
+		.platform_data = &ab8500_bm_data,
+		.pdata_size = sizeof(ab8500_bm_data),
+#endif
 	},
 	{
 		.name = "ab8500-btemp",
diff --git a/drivers/power/ab8500_charger.c b/drivers/power/ab8500_charger.c
index 723edb4..5156a98 100644
--- a/drivers/power/ab8500_charger.c
+++ b/drivers/power/ab8500_charger.c
@@ -23,6 +23,8 @@
 #include <linux/err.h>
 #include <linux/workqueue.h>
 #include <linux/kobject.h>
+#include <linux/of.h>
+#include <linux/mfd/core.h>
 #include <linux/mfd/abx500/ab8500.h>
 #include <linux/mfd/abx500.h>
 #include <linux/mfd/abx500/ab8500-bm.h>
@@ -181,9 +183,9 @@ struct ab8500_charger_usb_state {
  * @vbat		Battery voltage
  * @old_vbat		Previously measured battery voltage
  * @autopower		Indicate if we should have automatic pwron after pwrloss
+ * @autopower_cfg	platform specific power config support for "pwron after pwrloss"
  * @parent:		Pointer to the struct ab8500
  * @gpadc:		Pointer to the struct gpadc
- * @pdata:		Pointer to the abx500_charger platform data
  * @bat:		Pointer to the abx500_bm platform data
  * @flags:		Structure for information about events triggered
  * @usb_state:		Structure for usb stack information
@@ -218,9 +220,9 @@ struct ab8500_charger {
 	int vbat;
 	int old_vbat;
 	bool autopower;
+	bool autopower_cfg;
 	struct ab8500 *parent;
 	struct ab8500_gpadc *gpadc;
-	struct abx500_bmdevs_plat_data *pdata;
 	struct abx500_bm_data *bat;
 	struct ab8500_charger_event_flags flags;
 	struct ab8500_charger_usb_state usb_state;
@@ -322,7 +324,7 @@ static void ab8500_power_loss_handling(struct ab8500_charger *di)
 static void ab8500_power_supply_changed(struct ab8500_charger *di,
 					struct power_supply *psy)
 {
-	if (di->pdata->autopower_cfg) {
+	if (di->autopower_cfg) {
 		if (!di->usb.charger_connected &&
 		    !di->ac.charger_connected &&
 		    di->autopower) {
@@ -2526,25 +2528,47 @@ static int __devexit ab8500_charger_remove(struct platform_device *pdev)
 	power_supply_unregister(&di->usb_chg.psy);
 	power_supply_unregister(&di->ac_chg.psy);
 	platform_set_drvdata(pdev, NULL);
-	kfree(di);
 
 	return 0;
 }
 
+static char *supply_interface[] = {
+	"ab8500_chargalg",
+	"ab8500_fg",
+	"ab8500_btemp",
+};
+
 static int __devinit ab8500_charger_probe(struct platform_device *pdev)
 {
-	struct abx500_bmdevs_plat_data *plat_data = pdev->dev.platform_data;
+	struct device_node *np = pdev->dev.of_node;
 	struct ab8500_charger *di;
 	int irq, i, charger_status, ret = 0;
 
-	if (!plat_data) {
-		dev_err(&pdev->dev, "No platform data\n");
-		return -EINVAL;
+	di = devm_kzalloc(&pdev->dev, sizeof(*di), GFP_KERNEL);
+	if (!di) {
+		dev_err(&pdev->dev, "%s no mem for ab8500_charger\n", __func__);
+		return -ENOMEM;
 	}
 
-	di = kzalloc(sizeof(*di), GFP_KERNEL);
-	if (!di)
-		return -ENOMEM;
+	di->bat = pdev->mfd_cell->platform_data;
+	if (!di->bat) {
+		if (np) {
+			ret = bmdevs_of_probe(&pdev->dev, np, &di->bat);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"failed to get battery information\n");
+				return ret;
+			}
+			di->autopower_cfg =
+				of_property_read_bool(np, "autopower_cfg");
+		} else {
+			dev_err(&pdev->dev, "missing dt node for ab8500_charger\n");
+			return -EINVAL;
+		}
+	} else {
+		dev_info(&pdev->dev, "falling back to legacy platform data\n");
+		di->autopower_cfg = false;
+	}
 
 	/* get parent data */
 	di->dev = &pdev->dev;
@@ -2554,14 +2578,6 @@ static int __devinit ab8500_charger_probe(struct platform_device *pdev)
 	/* initialize lock */
 	spin_lock_init(&di->usb_state.usb_lock);
 
-	/* get charger specific platform data */
-	di->pdata = plat_data;
-	if (!di->pdata) {
-		dev_err(di->dev, "no charger platform data supplied\n");
-		ret = -EINVAL;
-		goto free_device_info;
-	}
-
 	di->autopower = false;
 
 	/* AC supply */
@@ -2571,8 +2587,8 @@ static int __devinit ab8500_charger_probe(struct platform_device *pdev)
 	di->ac_chg.psy.properties = ab8500_charger_ac_props;
 	di->ac_chg.psy.num_properties = ARRAY_SIZE(ab8500_charger_ac_props);
 	di->ac_chg.psy.get_property = ab8500_charger_ac_get_property;
-	di->ac_chg.psy.supplied_to = di->pdata->supplied_to;
-	di->ac_chg.psy.num_supplicants = di->pdata->num_supplicants;
+	di->ac_chg.psy.supplied_to = supply_interface;
+	di->ac_chg.psy.num_supplicants = ARRAY_SIZE(supply_interface),
 	/* ux500_charger sub-class */
 	di->ac_chg.ops.enable = &ab8500_charger_ac_en;
 	di->ac_chg.ops.kick_wd = &ab8500_charger_watchdog_kick;
@@ -2589,8 +2605,8 @@ static int __devinit ab8500_charger_probe(struct platform_device *pdev)
 	di->usb_chg.psy.properties = ab8500_charger_usb_props;
 	di->usb_chg.psy.num_properties = ARRAY_SIZE(ab8500_charger_usb_props);
 	di->usb_chg.psy.get_property = ab8500_charger_usb_get_property;
-	di->usb_chg.psy.supplied_to = di->pdata->supplied_to;
-	di->usb_chg.psy.num_supplicants = di->pdata->num_supplicants;
+	di->usb_chg.psy.supplied_to = supply_interface;
+	di->usb_chg.psy.num_supplicants = ARRAY_SIZE(supply_interface),
 	/* ux500_charger sub-class */
 	di->usb_chg.ops.enable = &ab8500_charger_usb_en;
 	di->usb_chg.ops.kick_wd = &ab8500_charger_watchdog_kick;
@@ -2606,8 +2622,7 @@ static int __devinit ab8500_charger_probe(struct platform_device *pdev)
 		create_singlethread_workqueue("ab8500_charger_wq");
 	if (di->charger_wq == NULL) {
 		dev_err(di->dev, "failed to create work queue\n");
-		ret = -ENOMEM;
-		goto free_device_info;
+		return -ENOMEM;
 	}
 
 	/* Init work for HW failure check */
@@ -2749,12 +2764,15 @@ free_regulator:
 	regulator_put(di->regu);
 free_charger_wq:
 	destroy_workqueue(di->charger_wq);
-free_device_info:
-	kfree(di);
 
 	return ret;
 }
 
+static const struct of_device_id ab8500_charger_match[] = {
+	{ .compatible = "stericsson,ab8500-charger", },
+	{ },
+};
+
 static struct platform_driver ab8500_charger_driver = {
 	.probe = ab8500_charger_probe,
 	.remove = __devexit_p(ab8500_charger_remove),
@@ -2763,6 +2781,7 @@ static struct platform_driver ab8500_charger_driver = {
 	.driver = {
 		.name = "ab8500-charger",
 		.owner = THIS_MODULE,
+		.of_match_table = ab8500_charger_match,
 	},
 };
 
-- 
1.7.10.4

[PATCH 4/4] mfd: ab8500: add devicetree support for chargalg

[Rajanikanth H.V]

From: "Rajanikanth H.V" <rajanikanth.hv@stericsson.com>

This patch adds device tree support for charging algorithm
driver

Signed-off-by: Rajanikanth H.V <rajanikanth.hv@linaro.org>
---
 .../bindings/power_supply/ab8500/chargalg.txt      |   16 ++++++
 arch/arm/boot/dts/dbx5x0.dtsi                      |    5 ++
 drivers/mfd/ab8500-core.c                          |    5 ++
 drivers/power/abx500_chargalg.c                    |   56 ++++++++++++++------
 include/linux/mfd/abx500.h                         |    6 ---
 5 files changed, 66 insertions(+), 22 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt

diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt b/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt
new file mode 100644
index 0000000..ef53283
--- /dev/null
+++ b/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt
@@ -0,0 +1,16 @@
+=== AB8500 Charging Algorithm Driver ===
+
+The properties below describes the node for chargalg driver.
+
+Required Properties:
+- compatible = Shall be: "stericsson,ab8500-chargalg"
+- battery = Shall be battery specific information
+
+Example:
+ab8500_chargalg {
+	compatible = "stericsson,ab8500-chargalg";
+	battery	   = <&ab8500_battery>;
+};
+
+For information on battery specific node, Ref:
+Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
index 7e9c01a..f1661b3 100644
--- a/arch/arm/boot/dts/dbx5x0.dtsi
+++ b/arch/arm/boot/dts/dbx5x0.dtsi
@@ -357,6 +357,11 @@
 					thermistor-on-batctrl;
 				};
 
+				ab8500-chargalg {
+					compatible	= "stericsson,ab8500-chargalg";
+					battery		= <&ab8500_battery>;
+				};
+
 				ab8500-charger {
 					compatible	= "stericsson,ab8500-charger";
 					battery		= <&ab8500_battery>;
diff --git a/drivers/mfd/ab8500-core.c b/drivers/mfd/ab8500-core.c
index c7a120b..5ec70f2 100644
--- a/drivers/mfd/ab8500-core.c
+++ b/drivers/mfd/ab8500-core.c
@@ -1071,8 +1071,13 @@ static struct mfd_cell __devinitdata ab8500_bm_devs[] = {
 	},
 	{
 		.name = "ab8500-chargalg",
+		.of_compatible = "stericsson,ab8500-chargalg",
 		.num_resources = ARRAY_SIZE(ab8500_chargalg_resources),
 		.resources = ab8500_chargalg_resources,
+#ifndef CONFIG_OF
+		.platform_data = &ab8500_bm_data,
+		.pdata_size = sizeof(ab8500_bm_data),
+#endif
 	},
 };
 
diff --git a/drivers/power/abx500_chargalg.c b/drivers/power/abx500_chargalg.c
index 94bf69b..96eb2c5 100644
--- a/drivers/power/abx500_chargalg.c
+++ b/drivers/power/abx500_chargalg.c
@@ -21,6 +21,8 @@
 #include <linux/completion.h>
 #include <linux/workqueue.h>
 #include <linux/kobject.h>
+#include <linux/of.h>
+#include <linux/mfd/core.h>
 #include <linux/mfd/abx500.h>
 #include <linux/mfd/abx500/ux500_chargalg.h>
 #include <linux/mfd/abx500/ab8500-bm.h>
@@ -205,7 +207,6 @@ enum maxim_ret {
  * @chg_info:		information about connected charger types
  * @batt_data:		data of the battery
  * @susp_status:	current charger suspension status
- * @pdata:		pointer to the abx500_chargalg platform data
  * @bat:		pointer to the abx500_bm platform data
  * @chargalg_psy:	structure that holds the battery properties exposed by
  *			the charging algorithm
@@ -231,7 +232,6 @@ struct abx500_chargalg {
 	struct abx500_chargalg_charger_info chg_info;
 	struct abx500_chargalg_battery_data batt_data;
 	struct abx500_chargalg_suspension_status susp_status;
-	struct abx500_bmdevs_plat_data *pdata;
 	struct abx500_bm_data *bat;
 	struct power_supply chargalg_psy;
 	struct ux500_charger *ac_chg;
@@ -1795,35 +1795,55 @@ static int __devexit abx500_chargalg_remove(struct platform_device *pdev)
 	flush_scheduled_work();
 	power_supply_unregister(&di->chargalg_psy);
 	platform_set_drvdata(pdev, NULL);
-	kfree(di);
 
 	return 0;
 }
 
+static char *supply_interface[] = {
+	"ab8500_fg",
+};
+
 static int __devinit abx500_chargalg_probe(struct platform_device *pdev)
 {
-	struct abx500_bmdevs_plat_data *plat_data;
+	struct device_node *np = pdev->dev.of_node;
+	struct abx500_chargalg *di;
 	int ret = 0;
 
-	struct abx500_chargalg *di =
-		kzalloc(sizeof(struct abx500_chargalg), GFP_KERNEL);
-	if (!di)
+	di = devm_kzalloc(&pdev->dev, sizeof(*di), GFP_KERNEL);
+	if (!di) {
+		dev_err(&pdev->dev, "%s no mem for ab8500_chargalg\n",
+			__func__);
 		return -ENOMEM;
+	}
+
+	di->bat = pdev->mfd_cell->platform_data;
+	if (!di->bat) {
+		if (np) {
+			ret = bmdevs_of_probe(&pdev->dev, np, &di->bat);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"failed to get battery information\n");
+				return ret;
+			}
+		} else {
+			dev_err(&pdev->dev, "missing dt node for ab8500_chargalg\n");
+			return -EINVAL;
+		}
+	} else {
+		dev_info(&pdev->dev, "falling back to legacy platform data\n");
+	}
 
 	/* get device struct */
 	di->dev = &pdev->dev;
 
-	plat_data = pdev->dev.platform_data;
-	di->pdata = plat_data;
-
 	/* chargalg supply */
 	di->chargalg_psy.name = "abx500_chargalg";
 	di->chargalg_psy.type = POWER_SUPPLY_TYPE_BATTERY;
 	di->chargalg_psy.properties = abx500_chargalg_props;
 	di->chargalg_psy.num_properties = ARRAY_SIZE(abx500_chargalg_props);
 	di->chargalg_psy.get_property = abx500_chargalg_get_property;
-	di->chargalg_psy.supplied_to = di->pdata->supplied_to;
-	di->chargalg_psy.num_supplicants = di->pdata->num_supplicants;
+	di->chargalg_psy.supplied_to = supply_interface;
+	di->chargalg_psy.num_supplicants = ARRAY_SIZE(supply_interface),
 	di->chargalg_psy.external_power_changed =
 		abx500_chargalg_external_power_changed;
 
@@ -1843,7 +1863,7 @@ static int __devinit abx500_chargalg_probe(struct platform_device *pdev)
 		create_singlethread_workqueue("abx500_chargalg_wq");
 	if (di->chargalg_wq == NULL) {
 		dev_err(di->dev, "failed to create work queue\n");
-		goto free_device_info;
+		return -ENOMEM;
 	}
 
 	/* Init work for chargalg */
@@ -1884,20 +1904,24 @@ free_psy:
 	power_supply_unregister(&di->chargalg_psy);
 free_chargalg_wq:
 	destroy_workqueue(di->chargalg_wq);
-free_device_info:
-	kfree(di);
 
 	return ret;
 }
 
+static const struct of_device_id ab8500_chargalg_match[] = {
+	{ .compatible = "stericsson,ab8500-chargalg", },
+	{ },
+};
+
 static struct platform_driver abx500_chargalg_driver = {
 	.probe = abx500_chargalg_probe,
 	.remove = __devexit_p(abx500_chargalg_remove),
 	.suspend = abx500_chargalg_suspend,
 	.resume = abx500_chargalg_resume,
 	.driver = {
-		.name = "abx500-chargalg",
+		.name = "ab8500-chargalg",
 		.owner = THIS_MODULE,
+		.of_match_table = ab8500_chargalg_match,
 	},
 };
 
diff --git a/include/linux/mfd/abx500.h b/include/linux/mfd/abx500.h
index 33f2c58..2138bd3 100644
--- a/include/linux/mfd/abx500.h
+++ b/include/linux/mfd/abx500.h
@@ -274,12 +274,6 @@ struct abx500_bm_data {
 
 extern struct abx500_bm_data ab8500_bm_data;
 
-struct abx500_bmdevs_plat_data {
-	char	**supplied_to;
-	size_t	num_supplicants;
-	bool	autopower_cfg;
-};
-
 enum {
 	NTC_EXTERNAL = 0,
 	NTC_INTERNAL,
-- 
1.7.10.4

Re: [PATCH 1/4] mfd: ab8500: add devicetree support for fuelgauge

[Anton Vorontsov]

On Fri, Nov 23, 2012 at 12:13:44AM +0530, Rajanikanth H.V wrote:
[...]
> +/*
> + * Note that the batres_vs_temp table must be strictly sorted by falling
> + * temperature values to work.
> + */
> +struct batres_vs_temp temp_to_batres_tbl_thermistor[] = {

It must be static.

[..]
> +struct batres_vs_temp temp_to_batres_tbl_ext_thermistor[] = {

Ditto.

> +	{ 60, 300},
> +	{ 30, 300},
> +	{ 20, 300},
> +	{ 10, 300},
> +	{ 00, 300},
> +	{-10, 300},
> +	{-20, 300},
> +};
> +
> +/* battery resistance table for LI ION 9100 battery */
> +struct batres_vs_temp temp_to_batres_tbl_9100[] = {

Ditto.

There are other issues, which I fixed in my tree for the previous series.
So the previous series already merged, please post patches on top of it.

Thanks,
Anton.

Re: [PATCH 1/4] mfd: ab8500: add devicetree support for fuelgauge

[Lee Jones]

> On Fri, Nov 23, 2012 at 12:13:44AM +0530, Rajanikanth H.V wrote:
> [...]
> > +/*
> > + * Note that the batres_vs_temp table must be strictly sorted by falling
> > + * temperature values to work.
> > + */
> > +struct batres_vs_temp temp_to_batres_tbl_thermistor[] = {
> 
> It must be static.
> 
> [..]
> > +struct batres_vs_temp temp_to_batres_tbl_ext_thermistor[] = {
> 
> Ditto.
> 
> > +	{ 60, 300},
> > +	{ 30, 300},
> > +	{ 20, 300},
> > +	{ 10, 300},
> > +	{ 00, 300},
> > +	{-10, 300},
> > +	{-20, 300},
> > +};
> > +
> > +/* battery resistance table for LI ION 9100 battery */
> > +struct batres_vs_temp temp_to_batres_tbl_9100[] = {
> 
> Ditto.
> 
> There are other issues, which I fixed in my tree for the previous series.
> So the previous series already merged, please post patches on top of it.

Ah, I see now. My apologies, I'll re-comment.

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH 4/4] mfd: ab8500: add devicetree support for chargalg

[Rajanikanth H.V]

From: "Rajanikanth H.V" <rajanikanth.hv@stericsson.com>

This patch adds device tree support for charging algorithm
driver

Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
---
 .../bindings/power_supply/ab8500/chargalg.txt      |   16 ++++++
 arch/arm/boot/dts/dbx5x0.dtsi                      |    5 ++
 drivers/mfd/ab8500-core.c                          |    5 ++
 drivers/power/abx500_chargalg.c                    |   54 ++++++++++++++------
 include/linux/mfd/abx500.h                         |    6 ---
 5 files changed, 64 insertions(+), 22 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt

diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt b/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt
new file mode 100644
index 0000000..ef53283
--- /dev/null
+++ b/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt
@@ -0,0 +1,16 @@
+=== AB8500 Charging Algorithm Driver ===
+
+The properties below describes the node for chargalg driver.
+
+Required Properties:
+- compatible = Shall be: "stericsson,ab8500-chargalg"
+- battery = Shall be battery specific information
+
+Example:
+ab8500_chargalg {
+	compatible = "stericsson,ab8500-chargalg";
+	battery	   = <&ab8500_battery>;
+};
+
+For information on battery specific node, Ref:
+Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
index b1ecb5d..a678afa 100644
--- a/arch/arm/boot/dts/dbx5x0.dtsi
+++ b/arch/arm/boot/dts/dbx5x0.dtsi
@@ -373,6 +373,11 @@
 					vddadc-supply	= <&ab8500_ldo_tvout_reg>;
 				};
 
+				ab8500_chargalg {
+					compatible	= "stericsson,ab8500-chargalg";
+					battery		= <&ab8500_battery>;
+				};
+
 				ab8500_usb {
 					compatible = "stericsson,ab8500-usb";
 					interrupts = < 90 0x4
diff --git a/drivers/mfd/ab8500-core.c b/drivers/mfd/ab8500-core.c
index c7a120b..5ec70f2 100644
--- a/drivers/mfd/ab8500-core.c
+++ b/drivers/mfd/ab8500-core.c
@@ -1071,8 +1071,13 @@ static struct mfd_cell __devinitdata ab8500_bm_devs[] = {
 	},
 	{
 		.name = "ab8500-chargalg",
+		.of_compatible = "stericsson,ab8500-chargalg",
 		.num_resources = ARRAY_SIZE(ab8500_chargalg_resources),
 		.resources = ab8500_chargalg_resources,
+#ifndef CONFIG_OF
+		.platform_data = &ab8500_bm_data,
+		.pdata_size = sizeof(ab8500_bm_data),
+#endif
 	},
 };
 
diff --git a/drivers/power/abx500_chargalg.c b/drivers/power/abx500_chargalg.c
index 88b5cc1..c603556 100644
--- a/drivers/power/abx500_chargalg.c
+++ b/drivers/power/abx500_chargalg.c
@@ -21,6 +21,8 @@
 #include <linux/completion.h>
 #include <linux/workqueue.h>
 #include <linux/kobject.h>
+#include <linux/of.h>
+#include <linux/mfd/core.h>
 #include <linux/mfd/abx500.h>
 #include <linux/mfd/abx500/ux500_chargalg.h>
 #include <linux/mfd/abx500/ab8500-bm.h>
@@ -205,7 +207,6 @@ enum maxim_ret {
  * @chg_info:		information about connected charger types
  * @batt_data:		data of the battery
  * @susp_status:	current charger suspension status
- * @pdata:		pointer to the abx500_chargalg platform data
  * @bat:		pointer to the abx500_bm platform data
  * @chargalg_psy:	structure that holds the battery properties exposed by
  *			the charging algorithm
@@ -231,7 +232,6 @@ struct abx500_chargalg {
 	struct abx500_chargalg_charger_info chg_info;
 	struct abx500_chargalg_battery_data batt_data;
 	struct abx500_chargalg_suspension_status susp_status;
-	struct abx500_bmdevs_plat_data *pdata;
 	struct abx500_bm_data *bat;
 	struct power_supply chargalg_psy;
 	struct ux500_charger *ac_chg;
@@ -1795,25 +1795,44 @@ static int __devexit abx500_chargalg_remove(struct platform_device *pdev)
 	flush_scheduled_work();
 	power_supply_unregister(&di->chargalg_psy);
 	platform_set_drvdata(pdev, NULL);
-	kfree(di);
 
 	return 0;
 }
 
+static char *supply_interface[] = {
+	"ab8500_fg",
+};
+
 static int __devinit abx500_chargalg_probe(struct platform_device *pdev)
 {
-	struct abx500_bmdevs_plat_data *plat_data;
+	struct device_node *np = pdev->dev.of_node;
+	struct abx500_chargalg *di;
 	int ret = 0;
 
-	struct abx500_chargalg *di =
-		kzalloc(sizeof(struct abx500_chargalg), GFP_KERNEL);
-	if (!di)
+	di = devm_kzalloc(&pdev->dev, sizeof(*di), GFP_KERNEL);
+	if (!di) {
+		dev_err(&pdev->dev, "%s no mem for ab8500_chargalg\n", __func__);
 		return -ENOMEM;
+	}
+	di->bat = pdev->mfd_cell->platform_data;
+	if (!di->bat) {
+		if (np) {
+			ret = bmdevs_of_probe(&pdev->dev, np, &di->bat);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"failed to get battery information\n");
+				return ret;
+			}
+		} else {
+			dev_err(&pdev->dev, "missing dt node for ab8500_chargalg\n");
+			return -EINVAL;
+		}
+	} else {
+		dev_info(&pdev->dev, "falling back to legacy platform data\n");
+	}
 
 	/* get device struct */
 	di->dev = &pdev->dev;
-	plat_data = pdev->dev.platform_data;
-	di->pdata = plat_data;
 
 	/* chargalg supply */
 	di->chargalg_psy.name = "abx500_chargalg";
@@ -1821,8 +1840,8 @@ static int __devinit abx500_chargalg_probe(struct platform_device *pdev)
 	di->chargalg_psy.properties = abx500_chargalg_props;
 	di->chargalg_psy.num_properties = ARRAY_SIZE(abx500_chargalg_props);
 	di->chargalg_psy.get_property = abx500_chargalg_get_property;
-	di->chargalg_psy.supplied_to = di->pdata->supplied_to;
-	di->chargalg_psy.num_supplicants = di->pdata->num_supplicants;
+	di->chargalg_psy.supplied_to = supply_interface;
+	di->chargalg_psy.num_supplicants = ARRAY_SIZE(supply_interface),
 	di->chargalg_psy.external_power_changed =
 		abx500_chargalg_external_power_changed;
 
@@ -1842,7 +1861,7 @@ static int __devinit abx500_chargalg_probe(struct platform_device *pdev)
 		create_singlethread_workqueue("abx500_chargalg_wq");
 	if (di->chargalg_wq == NULL) {
 		dev_err(di->dev, "failed to create work queue\n");
-		goto free_device_info;
+		return -ENOMEM;
 	}
 
 	/* Init work for chargalg */
@@ -1883,20 +1902,23 @@ free_psy:
 	power_supply_unregister(&di->chargalg_psy);
 free_chargalg_wq:
 	destroy_workqueue(di->chargalg_wq);
-free_device_info:
-	kfree(di);
-
 	return ret;
 }
 
+static const struct of_device_id ab8500_chargalg_match[] = {
+	{ .compatible = "stericsson,ab8500-chargalg", },
+	{ },
+};
+
 static struct platform_driver abx500_chargalg_driver = {
 	.probe = abx500_chargalg_probe,
 	.remove = __devexit_p(abx500_chargalg_remove),
 	.suspend = abx500_chargalg_suspend,
 	.resume = abx500_chargalg_resume,
 	.driver = {
-		.name = "abx500-chargalg",
+		.name = "ab8500-chargalg",
 		.owner = THIS_MODULE,
+		.of_match_table = ab8500_chargalg_match,
 	},
 };
 
diff --git a/include/linux/mfd/abx500.h b/include/linux/mfd/abx500.h
index bbf3ad6..a14c1a6 100644
--- a/include/linux/mfd/abx500.h
+++ b/include/linux/mfd/abx500.h
@@ -389,12 +389,6 @@ struct abx500_bm_data {
 
 extern struct abx500_bm_data ab8500_bm_data;
 
-struct abx500_bmdevs_plat_data {
-	char	**supplied_to;
-	size_t	num_supplicants;
-	bool	autopower_cfg;
-};
-
 enum {
 	NTC_EXTERNAL = 0,
 	NTC_INTERNAL,
-- 
1.7.10.4

Re: [PATCH 4/4] mfd: ab8500: add devicetree support for chargalg

[Francesco Lavra]

On 10/25/2012 08:30 AM, Rajanikanth H.V wrote:
> From: "Rajanikanth H.V" <rajanikanth.hv@stericsson.com>
> 
> This patch adds device tree support for charging algorithm
> driver
> 
> Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
[...]
> diff --git a/drivers/power/abx500_chargalg.c b/drivers/power/abx500_chargalg.c
> index 88b5cc1..829fcfd 100644
> --- a/drivers/power/abx500_chargalg.c
> +++ b/drivers/power/abx500_chargalg.c
> @@ -21,6 +21,8 @@
>  #include <linux/completion.h>
>  #include <linux/workqueue.h>
>  #include <linux/kobject.h>
> +#include <linux/of.h>
> +#include <linux/mfd/core.h>
>  #include <linux/mfd/abx500.h>
>  #include <linux/mfd/abx500/ux500_chargalg.h>
>  #include <linux/mfd/abx500/ab8500-bm.h>
> @@ -231,7 +233,6 @@ struct abx500_chargalg {
>  	struct abx500_chargalg_charger_info chg_info;
>  	struct abx500_chargalg_battery_data batt_data;
>  	struct abx500_chargalg_suspension_status susp_status;
> -	struct abx500_bmdevs_plat_data *pdata;

pdata should be removed from the description of the struct members as well.

>  	struct abx500_bm_data *bat;
>  	struct power_supply chargalg_psy;
>  	struct ux500_charger *ac_chg;
> @@ -1795,25 +1796,45 @@ static int __devexit abx500_chargalg_remove(struct platform_device *pdev)
>  	flush_scheduled_work();
>  	power_supply_unregister(&di->chargalg_psy);
>  	platform_set_drvdata(pdev, NULL);
> -	kfree(di);
>  
>  	return 0;
>  }
>  
> +static char *supply_interface[] = {
> +	"ab8500_fg",
> +};
> +
>  static int __devinit abx500_chargalg_probe(struct platform_device *pdev)
>  {
> -	struct abx500_bmdevs_plat_data *plat_data;
> +	struct device_node *np = pdev->dev.of_node;
> +	struct abx500_chargalg *di;
>  	int ret = 0;
>  
> -	struct abx500_chargalg *di =
> -		kzalloc(sizeof(struct abx500_chargalg), GFP_KERNEL);
> -	if (!di)
> +	di = devm_kzalloc(&pdev->dev, sizeof(*di), GFP_KERNEL);
> +	if (!di) {
> +		dev_err(&pdev->dev, "%s no mem for ab8500_chargalg\n", __func__);
>  		return -ENOMEM;
> +	}
> +	di->bat = pdev->mfd_cell->platform_data;
> +	if (!di->bat) {
> +		if (np) {
> +			ret = bmdevs_of_probe(&pdev->dev, np, &di->bat);
> +			if (ret) {
> +				dev_err(&pdev->dev,
> +					"failed to get battery information\n");
> +				return ret;
> +			}
> +		} else {
> +			dev_err(&pdev->dev, "missing dt node for ab8500_chargalg\n");
> +			return -EINVAL;
> +		}
> +	} else {
> +		dev_info(&pdev->dev, "falling back to legacy platform data\n");
> +		printk("%s falling back to legacy platform data\n", __func__);

You forgot to remove the printk() call.

--
Francesco