[PATCH v2 0/4] pinctrl: ABX500: fix

[PATCH v2 0/4] pinctrl: ABX500: fix

[patrice.chotard.st]

From: Patrice Chotard <patrice.chotard@st.com>

Patrice Chotard (4):
  pinctrl: abx500: suppress hardcoded value
  pinctrl: abx500: fix abx500_gpio_get()
  pinctrl: abx500: factorize code
  pinctrl: abx500: rework error path

 drivers/pinctrl/pinctrl-abx500.c       |  173 +++++++++++++++++++++++---------
 include/linux/mfd/abx500/ab8500-gpio.h |    5 +
 2 files changed, 132 insertions(+), 46 deletions(-)

-- 
1.7.10

[PATCH v2 1/4] pinctrl: abx500: suppress hardcoded value

[patrice.chotard.st]

From: Patrice Chotard <patrice.chotard@st.com>

Replace hardcoded value by corresponding #define's.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
---
 drivers/pinctrl/pinctrl-abx500.c       |   18 ++++++++++++++----
 include/linux/mfd/abx500/ab8500-gpio.h |    5 +++++
 2 files changed, 19 insertions(+), 4 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-abx500.c b/drivers/pinctrl/pinctrl-abx500.c
index caa7ab6..d1d42e7 100644
--- a/drivers/pinctrl/pinctrl-abx500.c
+++ b/drivers/pinctrl/pinctrl-abx500.c
@@ -264,12 +264,18 @@ static int abx500_gpio_direction_output(struct gpio_chip *chip,
 	int ret;
 
 	/* set direction as output */
-	ret = abx500_gpio_set_bits(chip, AB8500_GPIO_DIR1_REG, offset, 1);
+	ret = abx500_gpio_set_bits(chip,
+				AB8500_GPIO_DIR1_REG,
+				offset,
+				ABX500_GPIO_OUTPUT);
 	if (ret < 0)
 		return ret;
 
 	/* disable pull down */
-	ret = abx500_gpio_set_bits(chip, AB8500_GPIO_PUD1_REG, offset, 1);
+	ret = abx500_gpio_set_bits(chip,
+				AB8500_GPIO_PUD1_REG,
+				offset,
+				ABX500_GPIO_PULL_NONE);
 	if (ret < 0)
 		return ret;
 
@@ -290,7 +296,10 @@ static int abx500_gpio_direction_output(struct gpio_chip *chip,
 static int abx500_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
 {
 	/* set the register as input */
-	return abx500_gpio_set_bits(chip, AB8500_GPIO_DIR1_REG, offset, 0);
+	return abx500_gpio_set_bits(chip,
+				AB8500_GPIO_DIR1_REG,
+				offset,
+				ABX500_GPIO_INPUT);
 }
 
 static int abx500_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
@@ -1018,7 +1027,8 @@ static int abx500_pin_config_set(struct pinctrl_dev *pctldev,
 		else
 			/* Chip only supports pull down */
 			ret = abx500_gpio_set_bits(chip, AB8500_GPIO_PUD1_REG,
-				offset, argument ? 0 : 1);
+				offset,
+				argument ? ABX500_GPIO_PULL_DOWN : ABX500_GPIO_PULL_NONE);
 		break;
 
 	case PIN_CONFIG_BIAS_PULL_UP:
diff --git a/include/linux/mfd/abx500/ab8500-gpio.h b/include/linux/mfd/abx500/ab8500-gpio.h
index 172b2f2..dafeca4 100644
--- a/include/linux/mfd/abx500/ab8500-gpio.h
+++ b/include/linux/mfd/abx500/ab8500-gpio.h
@@ -30,4 +30,9 @@ enum abx500_gpio_vinsel {
 	ABX500_GPIO_VINSEL_VDD_BIF = 0x2,
 };
 
+enum abx500_gpio_direction {
+	ABX500_GPIO_INPUT = 0x0,
+	ABX500_GPIO_OUTPUT = 0x1,
+};
+
 #endif /* _AB8500_GPIO_H */
-- 
1.7.10

[PATCH v2 2/4] pinctrl: abx500: fix abx500_gpio_get()

[patrice.chotard.st]

From: Patrice Chotard <patrice.chotard@st.com>

_ allow to get output GPIO value
_ as there is no GPIO0 on ABX500, use correct offset with
  abx500_gpio_get_bit()

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
---
 drivers/pinctrl/pinctrl-abx500.c |   17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-abx500.c b/drivers/pinctrl/pinctrl-abx500.c
index d1d42e7..5bf66ad 100644
--- a/drivers/pinctrl/pinctrl-abx500.c
+++ b/drivers/pinctrl/pinctrl-abx500.c
@@ -162,10 +162,23 @@ static int abx500_gpio_get(struct gpio_chip *chip, unsigned offset)
 {
 	struct abx500_pinctrl *pct = to_abx500_pinctrl(chip);
 	bool bit;
+	bool is_out;
+	u8 gpio_offset = offset - 1;
 	int ret;
 
-	ret = abx500_gpio_get_bit(chip, AB8500_GPIO_IN1_REG,
-				  offset, &bit);
+	ret = abx500_gpio_get_bit(chip, AB8500_GPIO_DIR1_REG,
+			gpio_offset, &is_out);
+	if (ret < 0) {
+		dev_err(pct->dev, "%s failed\n", __func__);
+		return ret;
+	}
+
+	if (is_out)
+		ret = abx500_gpio_get_bit(chip, AB8500_GPIO_OUT1_REG,
+				gpio_offset, &bit);
+	else
+		ret = abx500_gpio_get_bit(chip, AB8500_GPIO_IN1_REG,
+				gpio_offset, &bit);
 	if (ret < 0) {
 		dev_err(pct->dev, "%s failed\n", __func__);
 		return ret;
-- 
1.7.10

[PATCH v2 3/4] pinctrl: abx500: factorize code

[patrice.chotard.st]

From: Patrice Chotard <patrice.chotard@st.com>

Factorize code by adding abx500_pullud_supported()
which improve code readability.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
---
 drivers/pinctrl/pinctrl-abx500.c |   32 +++++++++++++++-----------------
 1 file changed, 15 insertions(+), 17 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-abx500.c b/drivers/pinctrl/pinctrl-abx500.c
index 5bf66ad..f1ff701 100644
--- a/drivers/pinctrl/pinctrl-abx500.c
+++ b/drivers/pinctrl/pinctrl-abx500.c
@@ -267,12 +267,21 @@ out:
 	return ret;
 }
 
+static bool abx500_pullud_supported(struct gpio_chip *chip, unsigned gpio)
+{
+	struct abx500_pinctrl *pct = to_abx500_pinctrl(chip);
+	struct pullud *pullud = pct->soc->pullud;
+
+	return (pullud &&
+		gpio >= pullud->first_pin &&
+		gpio <= pullud->last_pin);
+}
+
 static int abx500_gpio_direction_output(struct gpio_chip *chip,
 					unsigned offset,
 					int val)
 {
 	struct abx500_pinctrl *pct = to_abx500_pinctrl(chip);
-	struct pullud *pullud = pct->soc->pullud;
 	unsigned gpio;
 	int ret;
 
@@ -294,7 +303,7 @@ static int abx500_gpio_direction_output(struct gpio_chip *chip,
 
 	/* if supported, disable both pull down and pull up */
 	gpio = offset + 1;
-	if (pullud && gpio >= pullud->first_pin && gpio <= pullud->last_pin) {
+	if (abx500_pullud_supported(chip, gpio)) {
 		ret = abx500_set_pull_updown(pct,
 				gpio,
 				ABX500_GPIO_PULL_NONE);
@@ -523,7 +532,6 @@ static void abx500_gpio_dbg_show_one(struct seq_file *s,
 				     unsigned offset, unsigned gpio)
 {
 	struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev);
-	struct pullud *pullud = pct->soc->pullud;
 	const char *label = gpiochip_is_requested(chip, offset - 1);
 	u8 gpio_offset = offset - 1;
 	int mode = -1;
@@ -552,9 +560,7 @@ static void abx500_gpio_dbg_show_one(struct seq_file *s,
 		   is_out ? "out" : "in ");
 
 	if (!is_out) {
-		if (pullud &&
-		   (offset >= pullud->first_pin) &&
-		   (offset <= pullud->last_pin)) {
+		if (abx500_pullud_supported(chip, offset)) {
 			abx500_get_pull_updown(pct, offset, &pud);
 			seq_printf(s, " %-9s", pull_up_down[pud]);
 		} else {
@@ -983,7 +989,6 @@ static int abx500_pin_config_set(struct pinctrl_dev *pctldev,
 			  unsigned long config)
 {
 	struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev);
-	struct pullud *pullud = pct->soc->pullud;
 	struct gpio_chip *chip = &pct->chip;
 	unsigned offset;
 	int ret = -EINVAL;
@@ -1008,9 +1013,7 @@ static int abx500_pin_config_set(struct pinctrl_dev *pctldev,
 		 * both features. If the pin is not within that range, we
 		 * fall back to the old bit set that only support pull down.
 		 */
-		if (pullud &&
-		    pin >= pullud->first_pin &&
-		    pin <= pullud->last_pin)
+		if (abx500_pullud_supported(chip, pin))
 			ret = abx500_set_pull_updown(pct,
 				pin,
 				ABX500_GPIO_PULL_NONE);
@@ -1031,9 +1034,7 @@ static int abx500_pin_config_set(struct pinctrl_dev *pctldev,
 		 * both features. If the pin is not within that range, we
 		 * fall back to the old bit set that only support pull down.
 		 */
-		if (pullud &&
-		    pin >= pullud->first_pin &&
-		    pin <= pullud->last_pin)
+		if (abx500_pullud_supported(chip, pin))
 			ret = abx500_set_pull_updown(pct,
 				pin,
 				argument ? ABX500_GPIO_PULL_DOWN : ABX500_GPIO_PULL_NONE);
@@ -1058,13 +1059,10 @@ static int abx500_pin_config_set(struct pinctrl_dev *pctldev,
 		 * both features. If the pin is not within that range, do
 		 * nothing
 		 */
-		if (pullud &&
-		    pin >= pullud->first_pin &&
-		    pin <= pullud->last_pin) {
+		if (abx500_pullud_supported(chip, pin))
 			ret = abx500_set_pull_updown(pct,
 				pin,
 				argument ? ABX500_GPIO_PULL_UP : ABX500_GPIO_PULL_NONE);
-		}
 		break;
 
 	case PIN_CONFIG_OUTPUT:
-- 
1.7.10

[PATCH v2 4/4] pinctrl: abx500: rework error path

[patrice.chotard.st]

From: Patrice Chotard <patrice.chotard@st.com>

At several places, return value was not tested
and error output was missing.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
---
 drivers/pinctrl/pinctrl-abx500.c |  114 +++++++++++++++++++++++++++++---------
 1 file changed, 87 insertions(+), 27 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-abx500.c b/drivers/pinctrl/pinctrl-abx500.c
index f1ff701..2b1da8f 100644
--- a/drivers/pinctrl/pinctrl-abx500.c
+++ b/drivers/pinctrl/pinctrl-abx500.c
@@ -131,8 +131,8 @@ static int abx500_gpio_get_bit(struct gpio_chip *chip, u8 reg,
 
 	if (ret < 0)
 		dev_err(pct->dev,
-			"%s read reg =%x, offset=%x failed\n",
-			__func__, reg, offset);
+			"%s read reg =%x, offset=%x failed (%d)\n",
+			__func__, reg, offset, ret);
 
 	return ret;
 }
@@ -148,7 +148,8 @@ static int abx500_gpio_set_bits(struct gpio_chip *chip, u8 reg,
 	ret = abx500_mask_and_set_register_interruptible(pct->dev,
 				AB8500_MISC, reg, BIT(pos), val << pos);
 	if (ret < 0)
-		dev_err(pct->dev, "%s write failed\n", __func__);
+		dev_err(pct->dev, "%s write reg, %x offset %x failed (%d)\n",
+				__func__, reg, offset, ret);
 
 	return ret;
 }
@@ -168,10 +169,8 @@ static int abx500_gpio_get(struct gpio_chip *chip, unsigned offset)
 
 	ret = abx500_gpio_get_bit(chip, AB8500_GPIO_DIR1_REG,
 			gpio_offset, &is_out);
-	if (ret < 0) {
-		dev_err(pct->dev, "%s failed\n", __func__);
-		return ret;
-	}
+	if (ret < 0)
+		goto out;
 
 	if (is_out)
 		ret = abx500_gpio_get_bit(chip, AB8500_GPIO_OUT1_REG,
@@ -179,8 +178,9 @@ static int abx500_gpio_get(struct gpio_chip *chip, unsigned offset)
 	else
 		ret = abx500_gpio_get_bit(chip, AB8500_GPIO_IN1_REG,
 				gpio_offset, &bit);
+out:
 	if (ret < 0) {
-		dev_err(pct->dev, "%s failed\n", __func__);
+		dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
 		return ret;
 	}
 
@@ -194,7 +194,7 @@ static void abx500_gpio_set(struct gpio_chip *chip, unsigned offset, int val)
 
 	ret = abx500_gpio_set_bits(chip, AB8500_GPIO_OUT1_REG, offset, val);
 	if (ret < 0)
-		dev_err(pct->dev, "%s write failed\n", __func__);
+		dev_err(pct->dev, "%s write failed (%d)\n", __func__, ret);
 }
 
 static int abx500_get_pull_updown(struct abx500_pinctrl *pct, int offset,
@@ -291,7 +291,7 @@ static int abx500_gpio_direction_output(struct gpio_chip *chip,
 				offset,
 				ABX500_GPIO_OUTPUT);
 	if (ret < 0)
-		return ret;
+		goto out;
 
 	/* disable pull down */
 	ret = abx500_gpio_set_bits(chip,
@@ -299,7 +299,7 @@ static int abx500_gpio_direction_output(struct gpio_chip *chip,
 				offset,
 				ABX500_GPIO_PULL_NONE);
 	if (ret < 0)
-		return ret;
+		goto out;
 
 	/* if supported, disable both pull down and pull up */
 	gpio = offset + 1;
@@ -307,8 +307,11 @@ static int abx500_gpio_direction_output(struct gpio_chip *chip,
 		ret = abx500_set_pull_updown(pct,
 				gpio,
 				ABX500_GPIO_PULL_NONE);
-		if (ret < 0)
-			return ret;
+	}
+out:
+	if (ret < 0) {
+		dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
+		return ret;
 	}
 
 	/* set the output as 1 or 0 */
@@ -406,10 +409,16 @@ static int abx500_set_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip,
 		if (af.alt_bit1 != UNUSED) {
 			ret = abx500_gpio_set_bits(chip, AB8500_GPIO_SEL1_REG,
 					offset, 0);
+			if (ret < 0)
+				goto out;
+
 			ret = abx500_gpio_set_bits(chip,
 					AB8500_GPIO_ALTFUN_REG,
 					af.alt_bit1,
 					!!(af.alta_val && BIT(0)));
+			if (ret < 0)
+				goto out;
+
 			if (af.alt_bit2 != UNUSED)
 				ret = abx500_gpio_set_bits(chip,
 					AB8500_GPIO_ALTFUN_REG,
@@ -423,8 +432,14 @@ static int abx500_set_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip,
 	case ABX500_ALT_B:
 		ret = abx500_gpio_set_bits(chip, AB8500_GPIO_SEL1_REG,
 				offset, 0);
+		if (ret < 0)
+			goto out;
+
 		ret = abx500_gpio_set_bits(chip, AB8500_GPIO_ALTFUN_REG,
 				af.alt_bit1, !!(af.altb_val && BIT(0)));
+		if (ret < 0)
+			goto out;
+
 		if (af.alt_bit2 != UNUSED)
 			ret = abx500_gpio_set_bits(chip,
 					AB8500_GPIO_ALTFUN_REG,
@@ -435,8 +450,14 @@ static int abx500_set_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip,
 	case ABX500_ALT_C:
 		ret = abx500_gpio_set_bits(chip, AB8500_GPIO_SEL1_REG,
 				offset, 0);
+		if (ret < 0)
+			goto out;
+
 		ret = abx500_gpio_set_bits(chip, AB8500_GPIO_ALTFUN_REG,
 				af.alt_bit2, !!(af.altc_val && BIT(0)));
+		if (ret < 0)
+			goto out;
+
 		ret = abx500_gpio_set_bits(chip, AB8500_GPIO_ALTFUN_REG,
 				af.alt_bit2, !!(af.altc_val && BIT(1)));
 		break;
@@ -446,11 +467,14 @@ static int abx500_set_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip,
 
 		return -EINVAL;
 	}
+out:
+	if (ret < 0)
+		dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
 
 	return ret;
 }
 
-static u8 abx500_get_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip,
+static int abx500_get_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip,
 			  unsigned gpio)
 {
 	u8 mode;
@@ -461,6 +485,7 @@ static u8 abx500_get_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip,
 	struct alternate_functions af = pct->soc->alternate_functions[gpio];
 	/* on ABx5xx, there is no GPIO0, so adjust the offset */
 	unsigned offset = gpio - 1;
+	int ret;
 
 	/*
 	 * if gpiosel_bit is set to unused,
@@ -470,8 +495,11 @@ static u8 abx500_get_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip,
 		return ABX500_DEFAULT;
 
 	/* read GpioSelx register */
-	abx500_gpio_get_bit(chip, AB8500_GPIO_SEL1_REG + (offset / 8),
+	ret = abx500_gpio_get_bit(chip, AB8500_GPIO_SEL1_REG + (offset / 8),
 			af.gpiosel_bit, &bit_mode);
+	if (ret < 0)
+		goto out;
+
 	mode = bit_mode;
 
 	/* sanity check */
@@ -503,14 +531,19 @@ static u8 abx500_get_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip,
 	 * pin use the AlternatFunction register
 	 * read alt_bit1 value
 	 */
-	abx500_gpio_get_bit(chip, AB8500_GPIO_ALTFUN_REG,
+	ret = abx500_gpio_get_bit(chip, AB8500_GPIO_ALTFUN_REG,
 			    af.alt_bit1, &alt_bit1);
+	if (ret < 0)
+		goto out;
 
-	if (af.alt_bit2 != UNUSED)
+	if (af.alt_bit2 != UNUSED) {
 		/* read alt_bit2 value */
-		abx500_gpio_get_bit(chip, AB8500_GPIO_ALTFUN_REG, af.alt_bit2,
+		ret = abx500_gpio_get_bit(chip, AB8500_GPIO_ALTFUN_REG,
+				af.alt_bit2,
 				&alt_bit2);
-	else
+		if (ret < 0)
+			goto out;
+	} else
 		alt_bit2 = 0;
 
 	mode = (alt_bit2 << 1) + alt_bit1;
@@ -520,6 +553,10 @@ static u8 abx500_get_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip,
 		return ABX500_ALT_B;
 	else
 		return ABX500_ALT_C;
+
+out:
+	dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
+	return ret;
 }
 
 #ifdef CONFIG_DEBUG_FS
@@ -538,6 +575,7 @@ static void abx500_gpio_dbg_show_one(struct seq_file *s,
 	bool is_out;
 	bool pd;
 	enum abx500_gpio_pull_updown pud = 0;
+	int ret;
 
 	const char *modes[] = {
 		[ABX500_DEFAULT]	= "default",
@@ -553,7 +591,10 @@ static void abx500_gpio_dbg_show_one(struct seq_file *s,
 		[ABX500_GPIO_PULL_UP]		= "pull up",
 	};
 
-	abx500_gpio_get_bit(chip, AB8500_GPIO_DIR1_REG, gpio_offset, &is_out);
+	ret = abx500_gpio_get_bit(chip, AB8500_GPIO_DIR1_REG,
+			gpio_offset, &is_out);
+	if (ret < 0)
+		goto out;
 
 	seq_printf(s, " gpio-%-3d (%-20.20s) %-3s",
 		   gpio, label ?: "(none)",
@@ -561,11 +602,17 @@ static void abx500_gpio_dbg_show_one(struct seq_file *s,
 
 	if (!is_out) {
 		if (abx500_pullud_supported(chip, offset)) {
-			abx500_get_pull_updown(pct, offset, &pud);
+			ret = abx500_get_pull_updown(pct, offset, &pud);
+			if (ret < 0)
+				goto out;
+
 			seq_printf(s, " %-9s", pull_up_down[pud]);
 		} else {
-			abx500_gpio_get_bit(chip, AB8500_GPIO_PUD1_REG,
-					    gpio_offset, &pd);
+			ret = abx500_gpio_get_bit(chip, AB8500_GPIO_PUD1_REG,
+					gpio_offset, &pd);
+			if (ret < 0)
+				goto out;
+
 			seq_printf(s, " %-9s", pull_up_down[pd]);
 		}
 	} else
@@ -575,6 +622,10 @@ static void abx500_gpio_dbg_show_one(struct seq_file *s,
 		mode = abx500_get_mode(pctldev, chip, offset);
 
 	seq_printf(s, " %s", (mode < 0) ? "unknown" : modes[mode]);
+
+out:
+	if (ret < 0)
+		dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
 }
 
 static void abx500_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
@@ -678,6 +729,9 @@ static int abx500_pmx_enable(struct pinctrl_dev *pctldev, unsigned function,
 		ret = abx500_set_mode(pctldev, chip, g->pins[i], g->altsetting);
 	}
 
+	if (ret < 0)
+		dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
+
 	return ret;
 }
 
@@ -726,10 +780,8 @@ static int abx500_gpio_request_enable(struct pinctrl_dev *pctldev,
 
 	ret = abx500_set_mode(pct->pctldev, &pct->chip,
 			      offset, p->altfunc);
-	if (ret < 0) {
+	if (ret < 0)
 		dev_err(pct->dev, "%s setting altfunc failed\n", __func__);
-		return ret;
-	}
 
 	return ret;
 }
@@ -1006,6 +1058,8 @@ static int abx500_pin_config_set(struct pinctrl_dev *pctldev,
 	switch (param) {
 	case PIN_CONFIG_BIAS_DISABLE:
 		ret = abx500_gpio_direction_input(chip, offset);
+		if (ret < 0)
+			goto out;
 		/*
 		 * Some chips only support pull down, while some actually
 		 * support both pull up and pull down. Such chips have
@@ -1025,6 +1079,8 @@ static int abx500_pin_config_set(struct pinctrl_dev *pctldev,
 
 	case PIN_CONFIG_BIAS_PULL_DOWN:
 		ret = abx500_gpio_direction_input(chip, offset);
+		if (ret < 0)
+			goto out;
 		/*
 		 * if argument = 1 set the pull down
 		 * else clear the pull down
@@ -1047,6 +1103,8 @@ static int abx500_pin_config_set(struct pinctrl_dev *pctldev,
 
 	case PIN_CONFIG_BIAS_PULL_UP:
 		ret = abx500_gpio_direction_input(chip, offset);
+		if (ret < 0)
+			goto out;
 		/*
 		 * if argument = 1 set the pull up
 		 * else clear the pull up
@@ -1067,12 +1125,14 @@ static int abx500_pin_config_set(struct pinctrl_dev *pctldev,
 
 	case PIN_CONFIG_OUTPUT:
 		ret = abx500_gpio_direction_output(chip, offset, argument);
-
 		break;
 
 	default:
 		dev_err(chip->dev, "illegal configuration requested\n");
 	}
+out:
+	if (ret < 0)
+		dev_err(pct->dev, "%s failed (%d)\n", __func__, ret);
 
 	return ret;
 }
-- 
1.7.10

Re: [PATCH v2 1/4] pinctrl: abx500: suppress hardcoded value

[Linus Walleij]

On Thu, Jun 20, 2013 at 4:05 PM,  <patrice.chotard.st@gmail.com> wrote:

> From: Patrice Chotard <patrice.chotard@st.com>
>
> Replace hardcoded value by corresponding #define's.
>
> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

This is not so good. The commit message is saying it
replaces values by #defines but is actually replacing it
by an enum.

Then you're in each instance calling

abx500_gpio_set_bits(struct gpio_chip *chip, u8 reg,
                unsigned offset, int val)

The last argument is a hardware register value, but here you
case an enum abx500_gpio_direction to an integer and pass
to this function.

It would be better if the patch did what it says: create a
#define for ABX500_GPIO_INPUT and ABX500_GPIO_OUTPUT
locally in drivers/pinctrl/pinctrl-abx500.c and use it locally
instead of touching <mfd/abx500/ab8500-gpio.h>.

Thanks,
Linus Walleij

Re: [PATCH v2 2/4] pinctrl: abx500: fix abx500_gpio_get()

[Linus Walleij]

On Thu, Jun 20, 2013 at 4:05 PM,  <patrice.chotard.st@gmail.com> wrote:

> From: Patrice Chotard <patrice.chotard@st.com>
>
> _ allow to get output GPIO value
> _ as there is no GPIO0 on ABX500, use correct offset with
>   abx500_gpio_get_bit()

Pls use a common dash "-" to prefix the items instead of
_underscore.

> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

Patch applied (after fixing commit message).

Yours,
Linus Walleij

Re: [PATCH v2 3/4] pinctrl: abx500: factorize code

[Linus Walleij]

On Thu, Jun 20, 2013 at 4:05 PM,  <patrice.chotard.st@gmail.com> wrote:

> From: Patrice Chotard <patrice.chotard@st.com>
>
> Factorize code by adding abx500_pullud_supported()
> which improve code readability.
>
> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

Patch applied, thanks!

Yours,
Linus Walleij

Re: [PATCH v2 4/4] pinctrl: abx500: rework error path

[Linus Walleij]

On Thu, Jun 20, 2013 at 4:05 PM,  <patrice.chotard.st@gmail.com> wrote:

> From: Patrice Chotard <patrice.chotard@st.com>
>
> At several places, return value was not tested
> and error output was missing.
>
> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

This looks fine, but does not apply since I didn't accept patch 1/4.

Please resend 1/4 and this 4/4 after fixing up 1/4.

(You can rebase onto devel if you want to be 100% sure it applies.)

Yours,
Linus Walleij

Re: [PATCH v2 1/4] pinctrl: abx500: suppress hardcoded value

[Patrice CHOTARD]

On 06/24/2013 01:29 PM, Linus Walleij wrote:

> On Thu, Jun 20, 2013 at 4:05 PM,  <patrice.chotard.st@gmail.com> wrote:
> 
>> From: Patrice Chotard <patrice.chotard@st.com>
>>
>> Replace hardcoded value by corresponding #define's.
>>
>> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
> 
> This is not so good. The commit message is saying it
> replaces values by #defines but is actually replacing it
> by an enum.
> 
> Then you're in each instance calling
> 
> abx500_gpio_set_bits(struct gpio_chip *chip, u8 reg,
>                 unsigned offset, int val)
> 
> The last argument is a hardware register value, but here you
> case an enum abx500_gpio_direction to an integer and pass
> to this function.
> 
> It would be better if the patch did what it says: create a
> #define for ABX500_GPIO_INPUT and ABX500_GPIO_OUTPUT
> locally in drivers/pinctrl/pinctrl-abx500.c and use it locally
> instead of touching <mfd/abx500/ab8500-gpio.h>.


Ok, i'll resubmit this

> 
> Thanks,
> Linus Walleij

Re: [PATCH v2 4/4] pinctrl: abx500: rework error path

[Patrice CHOTARD]

On 06/24/2013 01:37 PM, Linus Walleij wrote:

> On Thu, Jun 20, 2013 at 4:05 PM,  <patrice.chotard.st@gmail.com> wrote:
> 
>> From: Patrice Chotard <patrice.chotard@st.com>
>>
>> At several places, return value was not tested
>> and error output was missing.
>>
>> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
> 
> This looks fine, but does not apply since I didn't accept patch 1/4.


I am surprised that patch 4/4 doesn't apply, because in my side i am
able to apply it on your devel branch even without patch 1/4

Anyway, i'll submit 1/4 and 4/4.

Thanks

Patrice

>

> Please resend 1/4 and this 4/4 after fixing up 1/4.
> 
> (You can rebase onto devel if you want to be 100% sure it applies.)
> 
> Yours,
> Linus Walleij