[PATCH 00/10] ASoC: ARM: ux500: Better prepare for full Device Tree

[PATCH 00/10] ASoC: ARM: ux500: Better prepare for full Device Tree

[Lee Jones]

At this moment in time the Ux500 ASoC driver obtains its DMA information
via AUXDATA platform data passing. To make the driver more independent
we have to start extracting it from the Device Tree. This patch-set goes
some way to ensure the ux500 Audio driver is ready for the switch over.

 arch/arm/mach-ux500/board-mop500-audio.c     |   8 +++----
 include/linux/platform_data/asoc-ux500-msp.h |   9 +-------
 sound/soc/codecs/ab8500-codec.c              |   4 ++--
 sound/soc/ux500/mop500.c                     |   2 ++
 sound/soc/ux500/ux500_msp_dai.c              | 146 +++++++++++++++++++++++++++++++++++++++++++++++--------------------------------------------------------------------
 sound/soc/ux500/ux500_msp_i2s.c              |  56 ++++++++++++++++++++++++++++++++------------
 sound/soc/ux500/ux500_msp_i2s.h              |   2 +-
 sound/soc/ux500/ux500_pcm.c                  |  50 ++++++++++++++++++++++++++--------------
 8 files changed, 144 insertions(+), 133 deletions(-)

[PATCH 01/11] ARM: ux500: Don't use enums for MSP IDs - for easy DT conversion

[Lee Jones]

Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 arch/arm/mach-ux500/board-mop500-audio.c     | 8 ++++----
 include/linux/platform_data/asoc-ux500-msp.h | 9 +--------
 sound/soc/ux500/ux500_msp_i2s.h              | 2 +-
 3 files changed, 6 insertions(+), 13 deletions(-)

diff --git a/arch/arm/mach-ux500/board-mop500-audio.c b/arch/arm/mach-ux500/board-mop500-audio.c
index 154e15f..43d6cb8 100644
--- a/arch/arm/mach-ux500/board-mop500-audio.c
+++ b/arch/arm/mach-ux500/board-mop500-audio.c
@@ -31,7 +31,7 @@ static struct stedma40_chan_cfg msp0_dma_tx = {
 };
 
 struct msp_i2s_platform_data msp0_platform_data = {
-	.id = MSP_I2S_0,
+	.id = 0,
 	.msp_i2s_dma_rx = &msp0_dma_rx,
 	.msp_i2s_dma_tx = &msp0_dma_tx,
 };
@@ -49,7 +49,7 @@ static struct stedma40_chan_cfg msp1_dma_tx = {
 };
 
 struct msp_i2s_platform_data msp1_platform_data = {
-	.id = MSP_I2S_1,
+	.id = 1,
 	.msp_i2s_dma_rx = NULL,
 	.msp_i2s_dma_tx = &msp1_dma_tx,
 };
@@ -69,13 +69,13 @@ static struct stedma40_chan_cfg msp2_dma_tx = {
 };
 
 struct msp_i2s_platform_data msp2_platform_data = {
-	.id = MSP_I2S_2,
+	.id = 2,
 	.msp_i2s_dma_rx = &msp2_dma_rx,
 	.msp_i2s_dma_tx = &msp2_dma_tx,
 };
 
 struct msp_i2s_platform_data msp3_platform_data = {
-	.id		= MSP_I2S_3,
+	.id		= 3,
 	.msp_i2s_dma_rx	= &msp1_dma_rx,
 	.msp_i2s_dma_tx	= NULL,
 };
diff --git a/include/linux/platform_data/asoc-ux500-msp.h b/include/linux/platform_data/asoc-ux500-msp.h
index 9991aea..2f34bb9 100644
--- a/include/linux/platform_data/asoc-ux500-msp.h
+++ b/include/linux/platform_data/asoc-ux500-msp.h
@@ -10,16 +10,9 @@
 
 #include <linux/platform_data/dma-ste-dma40.h>
 
-enum msp_i2s_id {
-	MSP_I2S_0 = 0,
-	MSP_I2S_1,
-	MSP_I2S_2,
-	MSP_I2S_3,
-};
-
 /* Platform data structure for a MSP I2S-device */
 struct msp_i2s_platform_data {
-	enum msp_i2s_id id;
+	int id;
 	struct stedma40_chan_cfg *msp_i2s_dma_rx;
 	struct stedma40_chan_cfg *msp_i2s_dma_tx;
 };
diff --git a/sound/soc/ux500/ux500_msp_i2s.h b/sound/soc/ux500/ux500_msp_i2s.h
index 258d0bce..875de0f 100644
--- a/sound/soc/ux500/ux500_msp_i2s.h
+++ b/sound/soc/ux500/ux500_msp_i2s.h
@@ -475,7 +475,7 @@ struct ux500_msp_dma_params {
 };
 
 struct ux500_msp {
-	enum msp_i2s_id id;
+	int id;
 	void __iomem *registers;
 	struct device *dev;
 	struct ux500_msp_dma_params playback_dma_data;
-- 
1.8.3.2

[PATCH 02/11] ASoC: ab8500: Revert back to find_next_bit()

[Lee Jones]

Commit '166a34d ASoC: ab8500: Fix invalid cast to long pointer'
rather carelessly converts find_next_bit() to fls() (find last
bit set), which are not the same.

Although this implementation may not be portable, the alternative
breaks audio on anything using the AB8500 CODEC, which is a much
greater evil. Besides, this driver will never run on anything
else.

Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 sound/soc/codecs/ab8500-codec.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/sound/soc/codecs/ab8500-codec.c b/sound/soc/codecs/ab8500-codec.c
index 1ad92cb..51ae3e9 100644
--- a/sound/soc/codecs/ab8500-codec.c
+++ b/sound/soc/codecs/ab8500-codec.c
@@ -2322,7 +2322,7 @@ static int ab8500_codec_set_dai_tdm_slot(struct snd_soc_dai *dai,
 		slot = ffs(tx_mask);
 		snd_soc_update_bits(codec, AB8500_DASLOTCONF1, mask, slot);
 		snd_soc_update_bits(codec, AB8500_DASLOTCONF3, mask, slot);
-		slot = fls(tx_mask);
+		slot = find_next_bit((unsigned long *)&tx_mask, 32, slot + 1);
 		snd_soc_update_bits(codec, AB8500_DASLOTCONF2, mask, slot);
 		snd_soc_update_bits(codec, AB8500_DASLOTCONF4, mask, slot);
 		break;
@@ -2364,7 +2364,7 @@ static int ab8500_codec_set_dai_tdm_slot(struct snd_soc_dai *dai,
 				AB8500_ADSLOTSEL(slot),
 				AB8500_MASK_SLOT(slot),
 				AB8500_ADSLOTSELX_AD_OUT_TO_SLOT(AB8500_AD_OUT3, slot));
-		slot = fls(rx_mask);
+		slot = find_next_bit((unsigned long *)&rx_mask, 32, slot + 1);
 		snd_soc_update_bits(codec,
 				AB8500_ADSLOTSEL(slot),
 				AB8500_MASK_SLOT(slot),
-- 
1.8.3.2

[PATCH 03/11] ASoC: ux500: Provide better checking for Device Tree and/or Platform Data

[Lee Jones]

These drivers will not work without platform specific data, which is
passed in via Device Tree or Platform Data. To avoid the chance of
NULL pointer dereferencing and alike, let's ensure we have at least
one of the methods in play before continuing.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 sound/soc/ux500/ux500_msp_dai.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/sound/soc/ux500/ux500_msp_dai.c b/sound/soc/ux500/ux500_msp_dai.c
index c6fb5cc..bc042cc 100644
--- a/sound/soc/ux500/ux500_msp_dai.c
+++ b/sound/soc/ux500/ux500_msp_dai.c
@@ -771,10 +771,14 @@ static const struct snd_soc_component_driver ux500_msp_component = {
 static int ux500_msp_drv_probe(struct platform_device *pdev)
 {
 	struct ux500_msp_i2s_drvdata *drvdata;
+	struct msp_i2s_platform_data *pdata = pdev->dev.platform_data;
+	struct device_node *np = pdev->dev.of_node;
 	int ret = 0;
 
-	dev_dbg(&pdev->dev, "%s: Enter (pdev->name = %s).\n", __func__,
-		pdev->name);
+	if (!pdata && !np) {
+		dev_err(&pdev->dev, "No platform data or Device Tree found\n");
+		return -ENODEV;
+	}
 
 	drvdata = devm_kzalloc(&pdev->dev,
 				sizeof(struct ux500_msp_i2s_drvdata),
-- 
1.8.3.2

[PATCH 04/11] ASoC: Ux500: Match platform by device node when booting Device Tree

[Lee Jones]

We're getting closer to fully enabling the Ux500 ASoC driver for Device
Tree. When we switch over from using AUXDATA we'll need to match platform
by only Device Tree nodes. In this patch we NULL out the platform_name,
and supply nodes for each platform device.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 sound/soc/ux500/mop500.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/sound/soc/ux500/mop500.c b/sound/soc/ux500/mop500.c
index 178d1ba..b3b66aa 100644
--- a/sound/soc/ux500/mop500.c
+++ b/sound/soc/ux500/mop500.c
@@ -91,6 +91,8 @@ static int mop500_of_probe(struct platform_device *pdev,
 	for (i = 0; i < 2; i++) {
 		mop500_dai_links[i].cpu_of_node = msp_np[i];
 		mop500_dai_links[i].cpu_dai_name = NULL;
+		mop500_dai_links[i].platform_of_node = msp_np[i];
+		mop500_dai_links[i].platform_name = NULL;
 		mop500_dai_links[i].codec_of_node = codec_np;
 		mop500_dai_links[i].codec_name = NULL;
 	}
-- 
1.8.3.2

[PATCH 05/11] ASoC: ux500_pcm: Stop pretending that we support varying address widths

[Lee Jones]

The Slave Config's addr_width attribute is populated by data_width of
dma_cfg, which in turn is derived from dma_params' data_size attribute
and that comes from the slot_width which is always 16 bits (2 Bytes).
We're cutting out the middle man here and just setting the DMA Slave
Config directly.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 sound/soc/ux500/ux500_pcm.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/sound/soc/ux500/ux500_pcm.c b/sound/soc/ux500/ux500_pcm.c
index ce554de..32d4572 100644
--- a/sound/soc/ux500/ux500_pcm.c
+++ b/sound/soc/ux500/ux500_pcm.c
@@ -109,20 +109,19 @@ static int ux500_pcm_prepare_slave_config(struct snd_pcm_substream *substream,
 {
 	struct snd_soc_pcm_runtime *rtd = substream->private_data;
 	struct ux500_msp_dma_params *dma_params;
-	struct stedma40_chan_cfg *dma_cfg;
 	int ret;
 
 	dma_params = snd_soc_dai_get_dma_data(rtd->cpu_dai, substream);
-	dma_cfg = dma_params->dma_cfg;
 
 	ret = snd_hwparams_to_dma_slave_config(substream, params, slave_config);
 	if (ret)
 		return ret;
 
 	slave_config->dst_maxburst = 4;
-	slave_config->dst_addr_width = dma_cfg->dst_info.data_width;
 	slave_config->src_maxburst = 4;
-	slave_config->src_addr_width = dma_cfg->src_info.data_width;
+
+	slave_config->src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+	slave_config->dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
 
 	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
 		slave_config->dst_addr = dma_params->tx_rx_addr;
-- 
1.8.3.2

[PATCH 06/11] ASoC: ux500_pcm: Expect different saved DMA data when obtaining from DAI store

[Lee Jones]

In preparation for full Device Tree enablement we must differentiate
between the two varying ways DMA data can be held in the DAI store. If
we're booting with Device Tree the provided 'snd_dmaengine_dai_dma_data'
data structure shall be used, whereas in order to avoid breaking legacy
platform data we also need to be able to translate DMA data stored using
the UX500 specific 'ux500_msp_dma_params' method.

Once we move over to solely use Device Tree, we can enforce the use of
'snd_dmaengine_dai_dma_data' and this code can be removed altogether.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 sound/soc/ux500/ux500_pcm.c | 19 +++++++++++++++----
 1 file changed, 15 insertions(+), 4 deletions(-)

diff --git a/sound/soc/ux500/ux500_pcm.c b/sound/soc/ux500/ux500_pcm.c
index 32d4572..8b53f22 100644
--- a/sound/soc/ux500/ux500_pcm.c
+++ b/sound/soc/ux500/ux500_pcm.c
@@ -108,10 +108,21 @@ static int ux500_pcm_prepare_slave_config(struct snd_pcm_substream *substream,
 		struct dma_slave_config *slave_config)
 {
 	struct snd_soc_pcm_runtime *rtd = substream->private_data;
-	struct ux500_msp_dma_params *dma_params;
+	struct msp_i2s_platform_data *pdata = rtd->cpu_dai->dev->platform_data;
+	struct snd_dmaengine_dai_dma_data *snd_dma_params;
+	struct ux500_msp_dma_params *ste_dma_params;
+	dma_addr_t dma_addr;
 	int ret;
 
-	dma_params = snd_soc_dai_get_dma_data(rtd->cpu_dai, substream);
+	if (pdata) {
+		ste_dma_params =
+			snd_soc_dai_get_dma_data(rtd->cpu_dai, substream);
+		dma_addr = ste_dma_params->tx_rx_addr;
+	} else {
+		snd_dma_params =
+			snd_soc_dai_get_dma_data(rtd->cpu_dai, substream);
+		dma_addr = snd_dma_params->addr;
+	}
 
 	ret = snd_hwparams_to_dma_slave_config(substream, params, slave_config);
 	if (ret)
@@ -124,9 +135,9 @@ static int ux500_pcm_prepare_slave_config(struct snd_pcm_substream *substream,
 	slave_config->dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
 
 	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
-		slave_config->dst_addr = dma_params->tx_rx_addr;
+		slave_config->dst_addr = dma_addr;
 	else
-		slave_config->src_addr = dma_params->tx_rx_addr;
+		slave_config->src_addr = dma_addr;
 
 	return 0;
 }
-- 
1.8.3.2

[PATCH 07/11] ASoC: ux500_pcm: Extend Device Tree support to deal with DMA data

[Lee Jones]

Soon we will strip out pdata support from the Ux500 set of ASoC drivers.
When this happens it will have to supply a DMA slave_config to the
dmaengine. At the moment a great deal of this comes from pdata via
AUXDATA. We need to become independent of this soon. This patch starts
the process by allocating memory for the associated data structures and
fetches the MSP id used for const struct indexing.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 sound/soc/ux500/ux500_msp_i2s.c | 56 ++++++++++++++++++++++++++++++-----------
 1 file changed, 41 insertions(+), 15 deletions(-)

diff --git a/sound/soc/ux500/ux500_msp_i2s.c b/sound/soc/ux500/ux500_msp_i2s.c
index 1ca8b08..7f2a4ac 100644
--- a/sound/soc/ux500/ux500_msp_i2s.c
+++ b/sound/soc/ux500/ux500_msp_i2s.c
@@ -646,6 +646,34 @@ int ux500_msp_i2s_close(struct ux500_msp *msp, unsigned int dir)
 
 }
 
+int ux500_msp_i2s_of_init_msp(struct platform_device *pdev,
+			      struct ux500_msp *msp,
+			      struct msp_i2s_platform_data **platform_data)
+{
+	struct msp_i2s_platform_data *pdata;
+
+	*platform_data = devm_kzalloc(&pdev->dev,
+				     sizeof(struct msp_i2s_platform_data),
+				     GFP_KERNEL);
+	pdata = *platform_data;
+	if (!pdata)
+		return -ENOMEM;
+
+	msp->playback_dma_data.dma_cfg = devm_kzalloc(&pdev->dev,
+					sizeof(struct stedma40_chan_cfg),
+					GFP_KERNEL);
+	if (!msp->playback_dma_data.dma_cfg)
+		return -ENOMEM;
+
+	msp->capture_dma_data.dma_cfg = devm_kzalloc(&pdev->dev,
+					sizeof(struct stedma40_chan_cfg),
+					GFP_KERNEL);
+	if (!msp->capture_dma_data.dma_cfg)
+		return -ENOMEM;
+
+	return 0;
+}
+
 int ux500_msp_i2s_init_msp(struct platform_device *pdev,
 			struct ux500_msp **msp_p,
 			struct msp_i2s_platform_data *platform_data)
@@ -653,30 +681,28 @@ int ux500_msp_i2s_init_msp(struct platform_device *pdev,
 	struct resource *res = NULL;
 	struct device_node *np = pdev->dev.of_node;
 	struct ux500_msp *msp;
+	int ret;
 
 	*msp_p = devm_kzalloc(&pdev->dev, sizeof(struct ux500_msp), GFP_KERNEL);
 	msp = *msp_p;
 	if (!msp)
 		return -ENOMEM;
 
-	if (np) {
-		if (!platform_data) {
-			platform_data = devm_kzalloc(&pdev->dev,
-				sizeof(struct msp_i2s_platform_data), GFP_KERNEL);
-			if (!platform_data)
-				return -ENOMEM;
-		}
-	} else
-		if (!platform_data)
+	if (!platform_data) {
+		if (np) {
+			ret = ux500_msp_i2s_of_init_msp(pdev, msp,
+							&platform_data);
+			if (ret)
+				return ret;
+		} else
 			return -EINVAL;
+	} else {
+		msp->playback_dma_data.dma_cfg = platform_data->msp_i2s_dma_tx;
+		msp->capture_dma_data.dma_cfg = platform_data->msp_i2s_dma_rx;
+		msp->id = platform_data->id;
+	}
 
-	dev_dbg(&pdev->dev, "%s: Enter (name: %s, id: %d).\n", __func__,
-		pdev->name, platform_data->id);
-
-	msp->id = platform_data->id;
 	msp->dev = &pdev->dev;
-	msp->playback_dma_data.dma_cfg = platform_data->msp_i2s_dma_tx;
-	msp->capture_dma_data.dma_cfg = platform_data->msp_i2s_dma_rx;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (res == NULL) {
-- 
1.8.3.2

[PATCH 08/11] ASoC: ux500: Store DMA data in the DAI differently in the pdata and DT case

[Lee Jones]

In this patch we do two things. Firstly, instead of open coding the
store of DMA data in to the DAI for later use, we use the API provided.
Secondly we create and store similar DMA data for the DT case, only
this time we use 'struct snd_dmaengine_dai_dma_data' which is provided
by the core for this very reason.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 sound/soc/ux500/ux500_msp_dai.c | 42 +++++++++++++++++++++++++++++++++++++++--
 1 file changed, 40 insertions(+), 2 deletions(-)

diff --git a/sound/soc/ux500/ux500_msp_dai.c b/sound/soc/ux500/ux500_msp_dai.c
index bc042cc..f4d607a 100644
--- a/sound/soc/ux500/ux500_msp_dai.c
+++ b/sound/soc/ux500/ux500_msp_dai.c
@@ -17,12 +17,14 @@
 #include <linux/bitops.h>
 #include <linux/platform_device.h>
 #include <linux/clk.h>
+#include <linux/of.h>
 #include <linux/regulator/consumer.h>
 #include <linux/mfd/dbx500-prcmu.h>
 #include <linux/platform_data/asoc-ux500-msp.h>
 
 #include <sound/soc.h>
 #include <sound/soc-dai.h>
+#include <sound/dmaengine_pcm.h>
 
 #include "ux500_msp_i2s.h"
 #include "ux500_msp_dai.h"
@@ -654,16 +656,52 @@ static int ux500_msp_dai_trigger(struct snd_pcm_substream *substream,
 	return ret;
 }
 
+static int ux500_msp_dai_of_probe(struct snd_soc_dai *dai)
+{
+	struct ux500_msp_i2s_drvdata *drvdata = dev_get_drvdata(dai->dev);
+	struct snd_dmaengine_dai_dma_data *playback_dma_data;
+	struct snd_dmaengine_dai_dma_data *capture_dma_data;
+
+	playback_dma_data = devm_kzalloc(dai->dev,
+					 sizeof(*playback_dma_data),
+					 GFP_KERNEL);
+	if (!playback_dma_data)
+		return -ENOMEM;
+
+	capture_dma_data = devm_kzalloc(dai->dev,
+					sizeof(*capture_dma_data),
+					GFP_KERNEL);
+	if (!capture_dma_data)
+		return -ENOMEM;
+
+	playback_dma_data->addr = drvdata->msp->playback_dma_data.tx_rx_addr;
+	capture_dma_data->addr = drvdata->msp->capture_dma_data.tx_rx_addr;
+
+	playback_dma_data->maxburst = 4;
+	capture_dma_data->maxburst = 4;
+
+	snd_soc_dai_init_dma_data(dai, playback_dma_data, capture_dma_data);
+
+	return 0;
+}
+
 static int ux500_msp_dai_probe(struct snd_soc_dai *dai)
 {
 	struct ux500_msp_i2s_drvdata *drvdata = dev_get_drvdata(dai->dev);
+	struct msp_i2s_platform_data *pdata = dai->dev->platform_data;
+	int ret;
 
-	dai->playback_dma_data = &drvdata->msp->playback_dma_data;
-	dai->capture_dma_data = &drvdata->msp->capture_dma_data;
+	if (!pdata) {
+		ret = ux500_msp_dai_of_probe(dai);
+		return ret;
+	}
 
 	drvdata->msp->playback_dma_data.data_size = drvdata->slot_width;
 	drvdata->msp->capture_dma_data.data_size = drvdata->slot_width;
 
+	snd_soc_dai_init_dma_data(dai,
+				  &drvdata->msp->playback_dma_data,
+				  &drvdata->msp->capture_dma_data);
 	return 0;
 }
 
-- 
1.8.3.2

[PATCH 09/11] ASoC: ux500_pcm: Take out pointless dev_dbg() call

[Lee Jones]

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 sound/soc/ux500/ux500_pcm.c | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/sound/soc/ux500/ux500_pcm.c b/sound/soc/ux500/ux500_pcm.c
index 8b53f22..3d1c342 100644
--- a/sound/soc/ux500/ux500_pcm.c
+++ b/sound/soc/ux500/ux500_pcm.c
@@ -65,14 +65,10 @@ static struct dma_chan *ux500_pcm_request_chan(struct snd_soc_pcm_runtime *rtd,
 	struct snd_pcm_substream *substream)
 {
 	struct snd_soc_dai *dai = rtd->cpu_dai;
-	struct device *dev = dai->dev;
 	u16 per_data_width, mem_data_width;
 	struct stedma40_chan_cfg *dma_cfg;
 	struct ux500_msp_dma_params *dma_params;
 
-	dev_dbg(dev, "%s: MSP %d (%s): Enter.\n", __func__, dai->id,
-		snd_pcm_stream_str(substream));
-
 	dma_params = snd_soc_dai_get_dma_data(dai, substream);
 	dma_cfg = dma_params->dma_cfg;
 
-- 
1.8.3.2

[PATCH 10/11] ASoC: ux500_pcm: Differentiate between pdata and DT initialisation

[Lee Jones]

If booting with full DT support (i.e. DMA too, the last piece of the
puzzle), then we don't need to use the compatible_request_channel call
back or require some of the historical bumph which probably isn't
required by a platform data start-up now either. This will also be
ripped out in upcoming commits.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 sound/soc/ux500/ux500_pcm.c | 20 +++++++++++++++-----
 1 file changed, 15 insertions(+), 5 deletions(-)

diff --git a/sound/soc/ux500/ux500_pcm.c b/sound/soc/ux500/ux500_pcm.c
index 3d1c342..55a8634 100644
--- a/sound/soc/ux500/ux500_pcm.c
+++ b/sound/soc/ux500/ux500_pcm.c
@@ -145,15 +145,25 @@ static const struct snd_dmaengine_pcm_config ux500_dmaengine_pcm_config = {
 	.prepare_slave_config = ux500_pcm_prepare_slave_config,
 };
 
+static const struct snd_dmaengine_pcm_config ux500_dmaengine_of_pcm_config = {
+	.compat_request_channel = ux500_pcm_request_chan,
+	.prepare_slave_config = ux500_pcm_prepare_slave_config,
+};
+
 int ux500_pcm_register_platform(struct platform_device *pdev)
 {
+	const struct snd_dmaengine_pcm_config *pcm_config;
+	struct device_node *np = pdev->dev.of_node;
 	int ret;
 
-	ret = snd_dmaengine_pcm_register(&pdev->dev,
-			&ux500_dmaengine_pcm_config,
-			SND_DMAENGINE_PCM_FLAG_NO_RESIDUE |
-			SND_DMAENGINE_PCM_FLAG_COMPAT |
-			SND_DMAENGINE_PCM_FLAG_NO_DT);
+	if (np)
+		pcm_config = &ux500_dmaengine_of_pcm_config;
+	else
+		pcm_config = &ux500_dmaengine_pcm_config;
+
+	ret = snd_dmaengine_pcm_register(&pdev->dev, pcm_config,
+					 SND_DMAENGINE_PCM_FLAG_NO_RESIDUE |
+					 SND_DMAENGINE_PCM_FLAG_COMPAT);
 	if (ret < 0) {
 		dev_err(&pdev->dev,
 			"%s: ERROR: Failed to register platform '%s' (%d)!\n",
-- 
1.8.3.2

[PATCH 11/11] ASoC: ux500: Dramatically reduce the size of the DAI driver data struct

[Lee Jones]

We no longer have a means to differentiate between MSP devices at probe
time, mainly because we don't really have to. So rather than have an over-
sized static data structure in place, where the only difference between
devices is the ID and name (which are unused), we'll just create one
succinct, statically assigned and shared one instead.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 sound/soc/ux500/ux500_msp_dai.c | 96 ++++++-----------------------------------
 1 file changed, 14 insertions(+), 82 deletions(-)

diff --git a/sound/soc/ux500/ux500_msp_dai.c b/sound/soc/ux500/ux500_msp_dai.c
index f4d607a..5f4807b 100644
--- a/sound/soc/ux500/ux500_msp_dai.c
+++ b/sound/soc/ux500/ux500_msp_dai.c
@@ -718,87 +718,19 @@ static struct snd_soc_dai_ops ux500_msp_dai_ops[] = {
 	}
 };
 
-static struct snd_soc_dai_driver ux500_msp_dai_drv[UX500_NBR_OF_DAI] = {
-	{
-		.name = "ux500-msp-i2s.0",
-		.probe = ux500_msp_dai_probe,
-		.id = 0,
-		.suspend = NULL,
-		.resume = NULL,
-		.playback = {
-			.channels_min = UX500_MSP_MIN_CHANNELS,
-			.channels_max = UX500_MSP_MAX_CHANNELS,
-			.rates = UX500_I2S_RATES,
-			.formats = UX500_I2S_FORMATS,
-		},
-		.capture = {
-			.channels_min = UX500_MSP_MIN_CHANNELS,
-			.channels_max = UX500_MSP_MAX_CHANNELS,
-			.rates = UX500_I2S_RATES,
-			.formats = UX500_I2S_FORMATS,
-		},
-		.ops = ux500_msp_dai_ops,
-	},
-	{
-		.name = "ux500-msp-i2s.1",
-		.probe = ux500_msp_dai_probe,
-		.id = 1,
-		.suspend = NULL,
-		.resume = NULL,
-		.playback = {
-			.channels_min = UX500_MSP_MIN_CHANNELS,
-			.channels_max = UX500_MSP_MAX_CHANNELS,
-			.rates = UX500_I2S_RATES,
-			.formats = UX500_I2S_FORMATS,
-		},
-		.capture = {
-			.channels_min = UX500_MSP_MIN_CHANNELS,
-			.channels_max = UX500_MSP_MAX_CHANNELS,
-			.rates = UX500_I2S_RATES,
-			.formats = UX500_I2S_FORMATS,
-		},
-		.ops = ux500_msp_dai_ops,
-	},
-	{
-		.name = "ux500-msp-i2s.2",
-		.id = 2,
-		.probe = ux500_msp_dai_probe,
-		.suspend = NULL,
-		.resume = NULL,
-		.playback = {
-			.channels_min = UX500_MSP_MIN_CHANNELS,
-			.channels_max = UX500_MSP_MAX_CHANNELS,
-			.rates = UX500_I2S_RATES,
-			.formats = UX500_I2S_FORMATS,
-		},
-		.capture = {
-			.channels_min = UX500_MSP_MIN_CHANNELS,
-			.channels_max = UX500_MSP_MAX_CHANNELS,
-			.rates = UX500_I2S_RATES,
-			.formats = UX500_I2S_FORMATS,
-		},
-		.ops = ux500_msp_dai_ops,
-	},
-	{
-		.name = "ux500-msp-i2s.3",
-		.probe = ux500_msp_dai_probe,
-		.id = 3,
-		.suspend = NULL,
-		.resume = NULL,
-		.playback = {
-			.channels_min = UX500_MSP_MIN_CHANNELS,
-			.channels_max = UX500_MSP_MAX_CHANNELS,
-			.rates = UX500_I2S_RATES,
-			.formats = UX500_I2S_FORMATS,
-		},
-		.capture = {
-			.channels_min = UX500_MSP_MIN_CHANNELS,
-			.channels_max = UX500_MSP_MAX_CHANNELS,
-			.rates = UX500_I2S_RATES,
-			.formats = UX500_I2S_FORMATS,
-		},
-		.ops = ux500_msp_dai_ops,
-	},
+static struct snd_soc_dai_driver ux500_msp_dai_drv = {
+	.probe                 = ux500_msp_dai_probe,
+	.suspend               = NULL,
+	.resume                = NULL,
+	.playback.channels_min = UX500_MSP_MIN_CHANNELS,
+	.playback.channels_max = UX500_MSP_MAX_CHANNELS,
+	.playback.rates        = UX500_I2S_RATES,
+	.playback.formats      = UX500_I2S_FORMATS,
+	.capture.channels_min  = UX500_MSP_MIN_CHANNELS,
+	.capture.channels_max  = UX500_MSP_MAX_CHANNELS,
+	.capture.rates         = UX500_I2S_RATES,
+	.capture.formats       = UX500_I2S_FORMATS,
+	.ops                   = ux500_msp_dai_ops,
 };
 
 static const struct snd_soc_component_driver ux500_msp_component = {
@@ -868,7 +800,7 @@ static int ux500_msp_drv_probe(struct platform_device *pdev)
 	dev_set_drvdata(&pdev->dev, drvdata);
 
 	ret = snd_soc_register_component(&pdev->dev, &ux500_msp_component,
-					 &ux500_msp_dai_drv[drvdata->msp->id], 1);
+					 &ux500_msp_dai_drv, 1);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "Error: %s: Failed to register MSP%d!\n",
 			__func__, drvdata->msp->id);
-- 
1.8.3.2

Re: [PATCH 02/11] ASoC: ab8500: Revert back to find_next_bit()

[Takashi Iwai]

At Thu, 19 Dec 2013 15:54:59 +0000,
Lee Jones wrote:
> 
> Commit '166a34d ASoC: ab8500: Fix invalid cast to long pointer'
> rather carelessly converts find_next_bit() to fls() (find last
> bit set), which are not the same.

Does it break on the real machines?

fls() behaves differently from find_next_bit(), of course, but in this
case, it should work same in the end, since there are at most two
bits.


Takashi


> Although this implementation may not be portable, the alternative
> breaks audio on anything using the AB8500 CODEC, which is a much
> greater evil. Besides, this driver will never run on anything
> else.
> 
> Cc: Takashi Iwai <tiwai@suse.de>
> Signed-off-by: Lee Jones <lee.jones@linaro.org>
> ---
>  sound/soc/codecs/ab8500-codec.c | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/sound/soc/codecs/ab8500-codec.c b/sound/soc/codecs/ab8500-codec.c
> index 1ad92cb..51ae3e9 100644
> --- a/sound/soc/codecs/ab8500-codec.c
> +++ b/sound/soc/codecs/ab8500-codec.c
> @@ -2322,7 +2322,7 @@ static int ab8500_codec_set_dai_tdm_slot(struct snd_soc_dai *dai,
>  		slot = ffs(tx_mask);
>  		snd_soc_update_bits(codec, AB8500_DASLOTCONF1, mask, slot);
>  		snd_soc_update_bits(codec, AB8500_DASLOTCONF3, mask, slot);
> -		slot = fls(tx_mask);
> +		slot = find_next_bit((unsigned long *)&tx_mask, 32, slot + 1);
>  		snd_soc_update_bits(codec, AB8500_DASLOTCONF2, mask, slot);
>  		snd_soc_update_bits(codec, AB8500_DASLOTCONF4, mask, slot);
>  		break;
> @@ -2364,7 +2364,7 @@ static int ab8500_codec_set_dai_tdm_slot(struct snd_soc_dai *dai,
>  				AB8500_ADSLOTSEL(slot),
>  				AB8500_MASK_SLOT(slot),
>  				AB8500_ADSLOTSELX_AD_OUT_TO_SLOT(AB8500_AD_OUT3, slot));
> -		slot = fls(rx_mask);
> +		slot = find_next_bit((unsigned long *)&rx_mask, 32, slot + 1);
>  		snd_soc_update_bits(codec,
>  				AB8500_ADSLOTSEL(slot),
>  				AB8500_MASK_SLOT(slot),
> -- 
> 1.8.3.2
> 

Re: [PATCH 02/11] ASoC: ab8500: Revert back to find_next_bit()

[Lee Jones]

> > Commit '166a34d ASoC: ab8500: Fix invalid cast to long pointer'
> > rather carelessly converts find_next_bit() to fls() (find last
> > bit set), which are not the same.
> 
> Does it break on the real machines?

It does, that's how I found the bug.

> fls() behaves differently from find_next_bit(), of course, but in this
> case, it should work same in the end, since there are at most two
> bits.

Unfortunately it doesn't work at all. This patch brings audio back to
a working state. It took me the best part of a day to track down the
issue. :(

> > Although this implementation may not be portable, the alternative
> > breaks audio on anything using the AB8500 CODEC, which is a much
> > greater evil. Besides, this driver will never run on anything
> > else.
> > 
> > Cc: Takashi Iwai <tiwai@suse.de>
> > Signed-off-by: Lee Jones <lee.jones@linaro.org>
> > ---
> >  sound/soc/codecs/ab8500-codec.c | 4 ++--
> >  1 file changed, 2 insertions(+), 2 deletions(-)
> > 
> > diff --git a/sound/soc/codecs/ab8500-codec.c b/sound/soc/codecs/ab8500-codec.c
> > index 1ad92cb..51ae3e9 100644
> > --- a/sound/soc/codecs/ab8500-codec.c
> > +++ b/sound/soc/codecs/ab8500-codec.c
> > @@ -2322,7 +2322,7 @@ static int ab8500_codec_set_dai_tdm_slot(struct snd_soc_dai *dai,
> >  		slot = ffs(tx_mask);
> >  		snd_soc_update_bits(codec, AB8500_DASLOTCONF1, mask, slot);
> >  		snd_soc_update_bits(codec, AB8500_DASLOTCONF3, mask, slot);
> > -		slot = fls(tx_mask);
> > +		slot = find_next_bit((unsigned long *)&tx_mask, 32, slot + 1);
> >  		snd_soc_update_bits(codec, AB8500_DASLOTCONF2, mask, slot);
> >  		snd_soc_update_bits(codec, AB8500_DASLOTCONF4, mask, slot);
> >  		break;
> > @@ -2364,7 +2364,7 @@ static int ab8500_codec_set_dai_tdm_slot(struct snd_soc_dai *dai,
> >  				AB8500_ADSLOTSEL(slot),
> >  				AB8500_MASK_SLOT(slot),
> >  				AB8500_ADSLOTSELX_AD_OUT_TO_SLOT(AB8500_AD_OUT3, slot));
> > -		slot = fls(rx_mask);
> > +		slot = find_next_bit((unsigned long *)&rx_mask, 32, slot + 1);
> >  		snd_soc_update_bits(codec,
> >  				AB8500_ADSLOTSEL(slot),
> >  				AB8500_MASK_SLOT(slot),

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH 02/11] ASoC: ab8500: Revert back to find_next_bit()

[Takashi Iwai]

At Thu, 19 Dec 2013 16:48:24 +0000,
Lee Jones wrote:
> 
> > > Commit '166a34d ASoC: ab8500: Fix invalid cast to long pointer'
> > > rather carelessly converts find_next_bit() to fls() (find last
> > > bit set), which are not the same.
> > 
> > Does it break on the real machines?
> 
> It does, that's how I found the bug.
> 
> > fls() behaves differently from find_next_bit(), of course, but in this
> > case, it should work same in the end, since there are at most two
> > bits.
> 
> Unfortunately it doesn't work at all. This patch brings audio back to
> a working state. It took me the best part of a day to track down the
> issue. :(

Hmm, then isn't the original code rather buggy?

Check the values set there by ffs(), fls() and the original
find_next_bit(), especially whether find_next_bit() gives a valid
value fitting with the mask bits.


Takashi

Re: [PATCH 02/11] ASoC: ab8500: Revert back to find_next_bit()

[Lee Jones]

> > > > Commit '166a34d ASoC: ab8500: Fix invalid cast to long pointer'
> > > > rather carelessly converts find_next_bit() to fls() (find last
> > > > bit set), which are not the same.
> > > 
> > > Does it break on the real machines?
> > 
> > It does, that's how I found the bug.
> > 
> > > fls() behaves differently from find_next_bit(), of course, but in this
> > > case, it should work same in the end, since there are at most two
> > > bits.
> > 
> > Unfortunately it doesn't work at all. This patch brings audio back to
> > a working state. It took me the best part of a day to track down the
> > issue. :(
> 
> Hmm, then isn't the original code rather buggy?
> 
> Check the values set there by ffs(), fls() and the original
> find_next_bit(), especially whether find_next_bit() gives a valid
> value fitting with the mask bits.

I wish I had the time to delve into exactly what's happening. All I
can tell you is your patch broke audio and this one fixes it again. If
you have time for a deep dive and produce a permanent solution I'd be
much obliged and will of course test anything you send me. In the mean
time, this patch should definitely be applied, as sound is crippled
without it. 

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH 02/11] ASoC: ab8500: Revert back to find_next_bit()

[Takashi Iwai]

At Fri, 20 Dec 2013 14:02:11 +0000,
Lee Jones wrote:
> 
> > > > > Commit '166a34d ASoC: ab8500: Fix invalid cast to long pointer'
> > > > > rather carelessly converts find_next_bit() to fls() (find last
> > > > > bit set), which are not the same.
> > > > 
> > > > Does it break on the real machines?
> > > 
> > > It does, that's how I found the bug.
> > > 
> > > > fls() behaves differently from find_next_bit(), of course, but in this
> > > > case, it should work same in the end, since there are at most two
> > > > bits.
> > > 
> > > Unfortunately it doesn't work at all. This patch brings audio back to
> > > a working state. It took me the best part of a day to track down the
> > > issue. :(
> > 
> > Hmm, then isn't the original code rather buggy?
> > 
> > Check the values set there by ffs(), fls() and the original
> > find_next_bit(), especially whether find_next_bit() gives a valid
> > value fitting with the mask bits.
> 
> I wish I had the time to delve into exactly what's happening. All I
> can tell you is your patch broke audio and this one fixes it again. If
> you have time for a deep dive and produce a permanent solution I'd be
> much obliged and will of course test anything you send me. In the mean
> time, this patch should definitely be applied, as sound is crippled
> without it. 

The driver code was buggy from the beginning, but it looked as if
casually working in stereo mode.  May patch corrected things to what
it should be :)

I already have a fix patch, but need to check the information above at
first to see whether it can be used as is.  So, check the value set
there, and ffs(), fls() and find_next_bit() values.  Also, check
whether the stereo left/right channels are really output as expected
with the original driver code.


Takashi

Re: [PATCH 00/10] ASoC: ARM: ux500: Better prepare for full Device Tree

[Mark Brown]

On Thu, Dec 19, 2013 at 03:54:57PM +0000, Lee Jones wrote:
> At this moment in time the Ux500 ASoC driver obtains its DMA information
> via AUXDATA platform data passing. To make the driver more independent
> we have to start extracting it from the Device Tree. This patch-set goes
> some way to ensure the ux500 Audio driver is ready for the switch over.

This all looks good to me, I guess it's OK if I merge the ARM patch?

Re: [PATCH 00/10] ASoC: ARM: ux500: Better prepare for full Device Tree

[Lee Jones]

> > At this moment in time the Ux500 ASoC driver obtains its DMA information
> > via AUXDATA platform data passing. To make the driver more independent
> > we have to start extracting it from the Device Tree. This patch-set goes
> > some way to ensure the ux500 Audio driver is ready for the switch over.
> 
> This all looks good to me, I guess it's OK if I merge the ARM patch?

That would be up to Linus.

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH 02/11] ASoC: ab8500: Revert back to find_next_bit()

[Takashi Iwai]

At Thu, 19 Dec 2013 18:29:09 +0100,
Takashi Iwai wrote:
> 
> At Thu, 19 Dec 2013 16:48:24 +0000,
> Lee Jones wrote:
> > 
> > > > Commit '166a34d ASoC: ab8500: Fix invalid cast to long pointer'
> > > > rather carelessly converts find_next_bit() to fls() (find last
> > > > bit set), which are not the same.
> > > 
> > > Does it break on the real machines?
> > 
> > It does, that's how I found the bug.
> > 
> > > fls() behaves differently from find_next_bit(), of course, but in this
> > > case, it should work same in the end, since there are at most two
> > > bits.
> > 
> > Unfortunately it doesn't work at all. This patch brings audio back to
> > a working state. It took me the best part of a day to track down the
> > issue. :(
> 
> Hmm, then isn't the original code rather buggy?
> 
> Check the values set there by ffs(), fls() and the original
> find_next_bit(), especially whether find_next_bit() gives a valid
> value fitting with the mask bits.

Meanwhile, it's not good to keep the broken code in the upstream, and
the bug is obvious.  Below is the fixed patch, applicable with git am
scissors option.  Lee, let me know if this still doesn't fix.


thanks,

Takashi

-- 8< --
From: Takashi Iwai <tiwai@suse.de>
Subject: [PATCH] ASoC: ab8500: Back to first_find_bit() & co

ffs() and fls() give the off-by-one value in comparison with
find_*_bit() helpers, and find_first_bit() and find_next_bit() are
more intuitive in the case of two bits.  So, back to find_*_bit() but
call them properly without invalid cast.  This fixes the slot
assignment regression introduced by commit 166a34d27fca.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/soc/codecs/ab8500-codec.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/sound/soc/codecs/ab8500-codec.c b/sound/soc/codecs/ab8500-codec.c
index 1ad92cbf0b24..cf53c1e2fabc 100644
--- a/sound/soc/codecs/ab8500-codec.c
+++ b/sound/soc/codecs/ab8500-codec.c
@@ -2242,6 +2242,7 @@ static int ab8500_codec_set_dai_tdm_slot(struct snd_soc_dai *dai,
 {
 	struct snd_soc_codec *codec = dai->codec;
 	unsigned int val, mask, slot, slots_active;
+	unsigned long tmp;
 
 	mask = BIT(AB8500_DIGIFCONF2_IF0WL0) |
 		BIT(AB8500_DIGIFCONF2_IF0WL1);
@@ -2308,21 +2309,22 @@ static int ab8500_codec_set_dai_tdm_slot(struct snd_soc_dai *dai,
 	dev_dbg(dai->codec->dev, "%s: Slots, active, TX: %d\n", __func__,
 		slots_active);
 
+	tmp = tx_mask;
 	switch (slots_active) {
 	case 0:
 		break;
 	case 1:
-		slot = ffs(tx_mask);
+		slot = find_first_bit(&tmp, 32);
 		snd_soc_update_bits(codec, AB8500_DASLOTCONF1, mask, slot);
 		snd_soc_update_bits(codec, AB8500_DASLOTCONF3, mask, slot);
 		snd_soc_update_bits(codec, AB8500_DASLOTCONF2, mask, slot);
 		snd_soc_update_bits(codec, AB8500_DASLOTCONF4, mask, slot);
 		break;
 	case 2:
-		slot = ffs(tx_mask);
+		slot = find_first_bit(&tmp, 32);
 		snd_soc_update_bits(codec, AB8500_DASLOTCONF1, mask, slot);
 		snd_soc_update_bits(codec, AB8500_DASLOTCONF3, mask, slot);
-		slot = fls(tx_mask);
+		slot = find_next_bit(&tmp, 32, slot + 1);
 		snd_soc_update_bits(codec, AB8500_DASLOTCONF2, mask, slot);
 		snd_soc_update_bits(codec, AB8500_DASLOTCONF4, mask, slot);
 		break;
@@ -2349,22 +2351,23 @@ static int ab8500_codec_set_dai_tdm_slot(struct snd_soc_dai *dai,
 	dev_dbg(dai->codec->dev, "%s: Slots, active, RX: %d\n", __func__,
 		slots_active);
 
+	tmp = rx_mask;
 	switch (slots_active) {
 	case 0:
 		break;
 	case 1:
-		slot = ffs(rx_mask);
+		slot = find_first_bit(&tmp, 32);
 		snd_soc_update_bits(codec, AB8500_ADSLOTSEL(slot),
 				AB8500_MASK_SLOT(slot),
 				AB8500_ADSLOTSELX_AD_OUT_TO_SLOT(AB8500_AD_OUT3, slot));
 		break;
 	case 2:
-		slot = ffs(rx_mask);
+		slot = find_first_bit(&tmp, 32);
 		snd_soc_update_bits(codec,
 				AB8500_ADSLOTSEL(slot),
 				AB8500_MASK_SLOT(slot),
 				AB8500_ADSLOTSELX_AD_OUT_TO_SLOT(AB8500_AD_OUT3, slot));
-		slot = fls(rx_mask);
+		slot = find_next_bit(&tmp, 32, slot + 1);
 		snd_soc_update_bits(codec,
 				AB8500_ADSLOTSEL(slot),
 				AB8500_MASK_SLOT(slot),
-- 
1.8.5.2

Re: [PATCH 01/11] ARM: ux500: Don't use enums for MSP IDs - for easy DT conversion

[Linus Walleij]

On Thu, Dec 19, 2013 at 4:54 PM, Lee Jones <lee.jones@linaro.org> wrote:

> Signed-off-by: Lee Jones <lee.jones@linaro.org>

I guess it's best to merge this with the other ASoC patches
through Mark's tree?
Acked-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij

Re: [PATCH 00/10] ASoC: ARM: ux500: Better prepare for full Device Tree

[Linus Walleij]

On Sat, Dec 21, 2013 at 3:29 PM, Mark Brown <broonie@kernel.org> wrote:
> On Thu, Dec 19, 2013 at 03:54:57PM +0000, Lee Jones wrote:
>> At this moment in time the Ux500 ASoC driver obtains its DMA information
>> via AUXDATA platform data passing. To make the driver more independent
>> we have to start extracting it from the Device Tree. This patch-set goes
>> some way to ensure the ux500 Audio driver is ready for the switch over.
>
> This all looks good to me, I guess it's OK if I merge the ARM patch?

Yes I ACKed it now.

Sorry for slow response & thanks Mark.

Yours,
Linus Walleij

Re: [PATCH 01/11] ARM: ux500: Don't use enums for MSP IDs - for easy DT conversion

[Lee Jones]

On Tue, 07 Jan 2014, Linus Walleij wrote:

> On Thu, Dec 19, 2013 at 4:54 PM, Lee Jones <lee.jones@linaro.org> wrote:
> 
> > Signed-off-by: Lee Jones <lee.jones@linaro.org>
> 
> I guess it's best to merge this with the other ASoC patches
> through Mark's tree?
> Acked-by: Linus Walleij <linus.walleij@linaro.org>

I'm happy with that, although I haven't heard from Mark for ages.

Mark, are you still tracking this?

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH 01/11] ARM: ux500: Don't use enums for MSP IDs - for easy DT conversion

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 296 bytes --]

On Tue, Jan 07, 2014 at 02:11:54PM +0000, Lee Jones wrote:

> > Acked-by: Linus Walleij <linus.walleij@linaro.org>

> I'm happy with that, although I haven't heard from Mark for ages.

> Mark, are you still tracking this?

Yes, I've been waiting for both Linus and your testing of Takashi's fix.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH 01/11] ARM: ux500: Don't use enums for MSP IDs - for easy DT conversion

[Lee Jones]

On Tue, 07 Jan 2014, Mark Brown wrote:

> On Tue, Jan 07, 2014 at 02:11:54PM +0000, Lee Jones wrote:
> 
> > > Acked-by: Linus Walleij <linus.walleij@linaro.org>
> 
> > I'm happy with that, although I haven't heard from Mark for ages.
> 
> > Mark, are you still tracking this?
> 
> Yes, I've been waiting for both Linus and your testing of Takashi's fix.

Hmm... yes I need to get round to that, but it's not dependant on the
other patches in the set.

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH 01/11] ARM: ux500: Don't use enums for MSP IDs - for easy DT conversion

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 127 bytes --]

On Thu, Dec 19, 2013 at 03:54:58PM +0000, Lee Jones wrote:
> Signed-off-by: Lee Jones <lee.jones@linaro.org>

Applied, thanks.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH 03/11] ASoC: ux500: Provide better checking for Device Tree and/or Platform Data

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 335 bytes --]

On Thu, Dec 19, 2013 at 03:55:00PM +0000, Lee Jones wrote:
> These drivers will not work without platform specific data, which is
> passed in via Device Tree or Platform Data. To avoid the chance of
> NULL pointer dereferencing and alike, let's ensure we have at least
> one of the methods in play before continuing.

Applied, thanks.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH 04/11] ASoC: Ux500: Match platform by device node when booting Device Tree

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 346 bytes --]

On Thu, Dec 19, 2013 at 03:55:01PM +0000, Lee Jones wrote:
> We're getting closer to fully enabling the Ux500 ASoC driver for Device
> Tree. When we switch over from using AUXDATA we'll need to match platform
> by only Device Tree nodes. In this patch we NULL out the platform_name,
> and supply nodes for each platform device.

Applied, thanks.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH 05/11] ASoC: ux500_pcm: Stop pretending that we support varying address widths

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 384 bytes --]

On Thu, Dec 19, 2013 at 03:55:02PM +0000, Lee Jones wrote:
> The Slave Config's addr_width attribute is populated by data_width of
> dma_cfg, which in turn is derived from dma_params' data_size attribute
> and that comes from the slot_width which is always 16 bits (2 Bytes).
> We're cutting out the middle man here and just setting the DMA Slave
> Config directly.

Applied, thanks.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH 06/11] ASoC: ux500_pcm: Expect different saved DMA data when obtaining from DAI store

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 497 bytes --]

On Thu, Dec 19, 2013 at 03:55:03PM +0000, Lee Jones wrote:
> In preparation for full Device Tree enablement we must differentiate
> between the two varying ways DMA data can be held in the DAI store. If
> we're booting with Device Tree the provided 'snd_dmaengine_dai_dma_data'
> data structure shall be used, whereas in order to avoid breaking legacy
> platform data we also need to be able to translate DMA data stored using
> the UX500 specific 'ux500_msp_dma_params' method.

Applied, thanks.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH 07/11] ASoC: ux500_pcm: Extend Device Tree support to deal with DMA data

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 490 bytes --]

On Thu, Dec 19, 2013 at 03:55:04PM +0000, Lee Jones wrote:
> Soon we will strip out pdata support from the Ux500 set of ASoC drivers.
> When this happens it will have to supply a DMA slave_config to the
> dmaengine. At the moment a great deal of this comes from pdata via
> AUXDATA. We need to become independent of this soon. This patch starts
> the process by allocating memory for the associated data structures and
> fetches the MSP id used for const struct indexing.

Applied, thanks.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH 08/11] ASoC: ux500: Store DMA data in the DAI differently in the pdata and DT case

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 400 bytes --]

On Thu, Dec 19, 2013 at 03:55:05PM +0000, Lee Jones wrote:
> In this patch we do two things. Firstly, instead of open coding the
> store of DMA data in to the DAI for later use, we use the API provided.
> Secondly we create and store similar DMA data for the DT case, only
> this time we use 'struct snd_dmaengine_dai_dma_data' which is provided
> by the core for this very reason.

Applied, thanks.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH 09/11] ASoC: ux500_pcm: Take out pointless dev_dbg() call

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 180 bytes --]

On Thu, Dec 19, 2013 at 03:55:06PM +0000, Lee Jones wrote:
> Acked-by: Linus Walleij <linus.walleij@linaro.org>
> Signed-off-by: Lee Jones <lee.jones@linaro.org>

Applied, thanks.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH 10/11] ASoC: ux500_pcm: Differentiate between pdata and DT initialisation

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 392 bytes --]

On Thu, Dec 19, 2013 at 03:55:07PM +0000, Lee Jones wrote:
> If booting with full DT support (i.e. DMA too, the last piece of the
> puzzle), then we don't need to use the compatible_request_channel call
> back or require some of the historical bumph which probably isn't
> required by a platform data start-up now either. This will also be
> ripped out in upcoming commits.

Applied, thanks.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH 11/11] ASoC: ux500: Dramatically reduce the size of the DAI driver data struct

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 429 bytes --]

On Thu, Dec 19, 2013 at 03:55:08PM +0000, Lee Jones wrote:
> We no longer have a means to differentiate between MSP devices at probe
> time, mainly because we don't really have to. So rather than have an over-
> sized static data structure in place, where the only difference between
> devices is the ID and name (which are unused), we'll just create one
> succinct, statically assigned and shared one instead.

Applied, thanks.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]