* [PATCH v1 0/3] net: stmmac: Add STi GMAC ethernet
@ 2014-02-03 11:59 srinivas.kandagatla
2014-02-03 12:01 ` [PATCH v1 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
` (3 more replies)
0 siblings, 4 replies; 17+ messages in thread
From: srinivas.kandagatla @ 2014-02-03 11:59 UTC (permalink / raw)
To: netdev
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Russell King, Srinivas Kandagatla, Stuart Menefy,
Giuseppe Cavallaro, devicetree, linux-doc, linux-kernel,
linux-arm-kernel, kernel, davem
From: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Hi All,
This patch series adds Ethernet support to STi series SOCs STiH415 and STiH416.
STi SOC series integrates dwmac IP from synopsis, however there is a hardware
glue on top of this standard IP, this glue needs to configured before the
actual dwmac can be used. Also the glue logic needs re-configuring when the
link speed changes, This is because the clk source can change as the link
speed.
This patch just adds STi specific callbacks into of_data for configuring the
glue layer.
I have rebased my original patches (http://lkml.org/lkml/2013/11/12/243)
to latest stmmac which updates callbacks to suit glue drivers like this.
These patches are tested on b2000 and B2020 with STiH415 and STiH416.
Thanks,
srini
Srinivas Kandagatla (3):
net: stmmac:sti: Add STi SOC glue driver.
ARM: STi: Add STiH415 ethernet support.
ARM: STi: Add STiH416 ethernet support.
.../devicetree/bindings/net/sti-dwmac.txt | 58 ++++
arch/arm/boot/dts/stih415-clock.dtsi | 14 +
arch/arm/boot/dts/stih415-pinctrl.dtsi | 121 +++++++
arch/arm/boot/dts/stih415.dtsi | 48 +++
arch/arm/boot/dts/stih416-clock.dtsi | 14 +
arch/arm/boot/dts/stih416-pinctrl.dtsi | 109 +++++++
arch/arm/boot/dts/stih416.dtsi | 44 +++
arch/arm/boot/dts/stih41x-b2000.dtsi | 22 ++
arch/arm/boot/dts/stih41x-b2020.dtsi | 26 ++
drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 +
drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c | 331 ++++++++++++++++++++
drivers/net/ethernet/stmicro/stmmac/stmmac.h | 3 +
.../net/ethernet/stmicro/stmmac/stmmac_platform.c | 5 +
14 files changed, 807 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/sti-dwmac.txt
create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c
--
1.7.9.5
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH v1 1/3] net: stmmac:sti: Add STi SOC glue driver.
2014-02-03 11:59 [PATCH v1 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
@ 2014-02-03 12:01 ` srinivas.kandagatla
2014-02-07 3:53 ` David Miller
2014-02-03 12:01 ` [PATCH v1 2/3] ARM: STi: Add STiH415 ethernet support srinivas.kandagatla
` (2 subsequent siblings)
3 siblings, 1 reply; 17+ messages in thread
From: srinivas.kandagatla @ 2014-02-03 12:01 UTC (permalink / raw)
To: netdev
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Russell King, Srinivas Kandagatla, Stuart Menefy,
Giuseppe Cavallaro, devicetree, linux-doc, linux-kernel,
linux-arm-kernel, kernel, davem
From: Srinivas Kandagatla <srinivas.kandagatla@st.com>
STi series SOCs have a glue layer on top of the synopsis gmac IP, this
glue layer needs to be configured before the gmac driver starts using
the IP.
This patch adds a support to this glue layer which is configured via
stmmac setup, init, exit callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
---
.../devicetree/bindings/net/sti-dwmac.txt | 58 ++++
drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 +
drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c | 331 ++++++++++++++++++++
drivers/net/ethernet/stmicro/stmmac/stmmac.h | 3 +
.../net/ethernet/stmicro/stmmac/stmmac_platform.c | 5 +
6 files changed, 409 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/sti-dwmac.txt
create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c
diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt
new file mode 100644
index 0000000..3dd3d0b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt
@@ -0,0 +1,58 @@
+STMicroelectronics SoC DWMAC glue layer controller
+
+The device node has following properties.
+
+Required properties:
+ - compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac" or
+ "st,stid127-dwmac".
+ - reg : Offset of the glue configuration register map in system
+ configuration regmap pointed by st,syscon property and size.
+
+ - reg-names : Should be "sti-ethconf".
+
+ - st,syscon : Should be phandle to system configuration node which
+ encompases this glue registers.
+
+ - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be
+ wired up in from different sources. One via TXCLK pin and other via CLK_125
+ pin. This wiring is totally board dependent. However the retiming glue
+ logic should be configured accordingly. Possible values for this property
+
+ "txclk" - if 125Mhz clock is wired up via txclk line.
+ "clk_125" - if 125Mhz clock is wired up via clk_125 line.
+
+ This property is only valid for Giga bit setup( GMII, RGMII), and it is
+ un-used for non-giga bit (MII and RMII) setups. Also note that internal
+ clockgen can not generate stable 125Mhz clock.
+
+ - st,ext-phyclk: This boolean property indicates who is generating the clock
+ for tx and rx. This property is only valid for RMII case where the clock can
+ be generated from the MAC or PHY.
+
+ - clock-names: should be "sti-ethclk".
+ - clocks: Should point to ethernet clockgen which can generate phyclk.
+
+
+Example:
+
+ethernet0: dwmac@fe810000 {
+ device_type = "network";
+ compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+ reg = <0xfe810000 0x8000>, <0x8bc 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+ interrupts = <0 133 0>, <0 134 0>, <0 135 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+ phy-mode = "mii";
+
+ st,syscon = <&syscfg_rear>;
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+
+ resets = <&softreset STIH416_ETH0_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-0 = <&pinctrl_mii0>;
+ pinctrl-names = "default";
+ clocks = <&CLK_S_GMAC0_PHY>;
+ clock-names = "stmmaceth";
+};
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index e2f202e..f2d7c70 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -37,6 +37,17 @@ config DWMAC_SUNXI
stmmac device driver. This driver is used for A20/A31
GMAC ethernet controller.
+config DWMAC_STI
+ bool "STi GMAC support"
+ depends on STMMAC_PLATFORM && ARCH_STI
+ default y
+ ---help---
+ Support for ethernet controller on STi SOCs.
+
+ This selects STi SoC glue layer support for the stmmac
+ device driver. This driver is used on for the STi series
+ SOCs GMAC ethernet controller.
+
config STMMAC_PCI
bool "STMMAC PCI bus support"
depends on STMMAC_ETH && PCI
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index ecadece..dcef287 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -2,6 +2,7 @@ obj-$(CONFIG_STMMAC_ETH) += stmmac.o
stmmac-$(CONFIG_STMMAC_PLATFORM) += stmmac_platform.o
stmmac-$(CONFIG_STMMAC_PCI) += stmmac_pci.o
stmmac-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o
+stmmac-$(CONFIG_DWMAC_STI) += dwmac-sti.o
stmmac-objs:= stmmac_main.o stmmac_ethtool.o stmmac_mdio.o ring_mode.o \
chain_mode.o dwmac_lib.o dwmac1000_core.o dwmac1000_dma.o \
dwmac100_core.o dwmac100_dma.o enh_desc.o norm_desc.o \
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c
new file mode 100644
index 0000000..d87584cb
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c
@@ -0,0 +1,331 @@
+/**
+ * dwmac-sti.c - STMicroelectronics DWMAC Specific Glue layer
+ *
+ * Copyright (C) 2003-2014 STMicroelectronics (R&D) Limited
+ * Author: Srinivas Kandagatla <srinivas.kandagatla@st.com>
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/stmmac.h>
+#include <linux/phy.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+
+/**
+ * STi GMAC glue logic.
+ * --------------------
+ *
+ * _
+ * | \
+ * --------|0 \ ETH_SEL_INTERNAL_NOTEXT_PHYCLK
+ * phyclk | |___________________________________________
+ * | | | (phyclk-in)
+ * --------|1 / |
+ * int-clk |_ / |
+ * | _
+ * | | \
+ * |_______|0 \ ETH_SEL_TX_RETIME_CLK
+ * | |___________________________
+ * | | (tx-retime-clk)
+ * _______|1 /
+ * | |_ /
+ * _ |
+ * | \ |
+ * --------|0 \ |
+ * clk_125 | |__|
+ * | | ETH_SEL_TXCLK_NOT_CLK125
+ * --------|1 /
+ * txclk |_ /
+ *
+ *
+ * ETH_SEL_INTERNAL_NOTEXT_PHYCLK is valid only for RMII where PHY can
+ * generate 50MHz clock or MAC can generate it.
+ * This bit is configured by "st,ext-phyclk" property.
+ *
+ * ETH_SEL_TXCLK_NOT_CLK125 is only valid for gigabit modes, where the 125Mhz
+ * clock either comes from clk-125 pin or txclk pin. This configuration is
+ * totally driven by the board wiring. This bit is configured by
+ * "st,tx-retime-src" property.
+ *
+ * TXCLK configuration is different for different phy interface modes
+ * and changes according to link speed in modes like RGMII.
+ *
+ * Below table summarizes the clock requirement and clock sources for
+ * supported phy interface modes with link speeds.
+ * ________________________________________________
+ *| PHY_MODE | 1000 Mbit Link | 100 Mbit Link |
+ * ------------------------------------------------
+ *| MII | n/a | 25Mhz |
+ *| | | txclk |
+ * ------------------------------------------------
+ *| GMII | 125Mhz | 25Mhz |
+ *| | clk-125/txclk | txclk |
+ * ------------------------------------------------
+ *| RGMII | 125Mhz | 25Mhz |
+ *| | clk-125/txclk | clkgen |
+ * ------------------------------------------------
+ *| RMII | n/a | 25Mhz |
+ *| | |clkgen/phyclk-in |
+ * ------------------------------------------------
+ *
+ * TX lines are always retimed with a clk, which can vary depending
+ * on the board configuration. Below is the table of these bits
+ * in eth configuration register depending on source of retime clk.
+ *
+ *---------------------------------------------------------------
+ * src | tx_rt_clk | int_not_ext_phyclk | txclk_n_clk125|
+ *---------------------------------------------------------------
+ * txclk | 0 | n/a | 1 |
+ *---------------------------------------------------------------
+ * ck_125| 0 | n/a | 0 |
+ *---------------------------------------------------------------
+ * phyclk| 1 | 0 | n/a |
+ *---------------------------------------------------------------
+ * clkgen| 1 | 1 | n/a |
+ *---------------------------------------------------------------
+ */
+
+ /* Register definition */
+
+ /* 3 bits [8:6]
+ * [6:6] ETH_SEL_TXCLK_NOT_CLK125
+ * [7:7] ETH_SEL_INTERNAL_NOTEXT_PHYCLK
+ * [8:8] ETH_SEL_TX_RETIME_CLK
+ *
+ */
+
+#define TX_RETIME_SRC_MASK GENMASK(8, 6)
+#define ETH_SEL_TX_RETIME_CLK BIT(8)
+#define ETH_SEL_INTERNAL_NOTEXT_PHYCLK BIT(7)
+#define ETH_SEL_TXCLK_NOT_CLK125 BIT(6)
+
+#define ENMII_MASK GENMASK(5, 5)
+#define ENMII BIT(5)
+
+/**
+ * 3 bits [4:2]
+ * 000-GMII/MII
+ * 001-RGMII
+ * 010-SGMII
+ * 100-RMII
+*/
+#define MII_PHY_SEL_MASK GENMASK(4, 2)
+#define ETH_PHY_SEL_RMII BIT(4)
+#define ETH_PHY_SEL_SGMII BIT(3)
+#define ETH_PHY_SEL_RGMII BIT(2)
+#define ETH_PHY_SEL_GMII 0x0
+#define ETH_PHY_SEL_MII 0x0
+
+#define IS_PHY_IF_MODE_RGMII(iface) (iface == PHY_INTERFACE_MODE_RGMII || \
+ iface == PHY_INTERFACE_MODE_RGMII_ID || \
+ iface == PHY_INTERFACE_MODE_RGMII_RXID || \
+ iface == PHY_INTERFACE_MODE_RGMII_TXID)
+
+#define IS_PHY_IF_MODE_GBIT(iface) (IS_PHY_IF_MODE_RGMII(iface) || \
+ iface == PHY_INTERFACE_MODE_GMII)
+
+struct sti_dwmac {
+ int interface;
+ bool ext_phyclk;
+ bool is_tx_retime_src_clk_125;
+ struct clk *clk;
+ int reg;
+ struct device *dev;
+ struct regmap *regmap;
+};
+
+static u32 phy_intf_sels[] = {
+ [PHY_INTERFACE_MODE_MII] = ETH_PHY_SEL_MII,
+ [PHY_INTERFACE_MODE_GMII] = ETH_PHY_SEL_GMII,
+ [PHY_INTERFACE_MODE_RGMII] = ETH_PHY_SEL_RGMII,
+ [PHY_INTERFACE_MODE_RGMII_ID] = ETH_PHY_SEL_RGMII,
+ [PHY_INTERFACE_MODE_SGMII] = ETH_PHY_SEL_SGMII,
+ [PHY_INTERFACE_MODE_RMII] = ETH_PHY_SEL_RMII,
+};
+
+enum {
+ TX_RETIME_SRC_NA = 0,
+ TX_RETIME_SRC_TXCLK = 1,
+ TX_RETIME_SRC_CLK_125,
+ TX_RETIME_SRC_PHYCLK,
+ TX_RETIME_SRC_CLKGEN,
+};
+
+static const char * const tx_retime_srcs[] = {
+ [TX_RETIME_SRC_NA] = "",
+ [TX_RETIME_SRC_TXCLK] = "txclk",
+ [TX_RETIME_SRC_CLK_125] = "clk_125",
+ [TX_RETIME_SRC_PHYCLK] = "phyclk",
+ [TX_RETIME_SRC_CLKGEN] = "clkgen",
+};
+
+static u32 tx_retime_val[] = {
+ [TX_RETIME_SRC_TXCLK] = ETH_SEL_TXCLK_NOT_CLK125,
+ [TX_RETIME_SRC_CLK_125] = 0x0,
+ [TX_RETIME_SRC_PHYCLK] = ETH_SEL_TX_RETIME_CLK,
+ [TX_RETIME_SRC_CLKGEN] = ETH_SEL_TX_RETIME_CLK |
+ ETH_SEL_INTERNAL_NOTEXT_PHYCLK,
+};
+
+static void setup_retime_src(struct sti_dwmac *dwmac, u32 spd)
+{
+ u32 src = 0, freq = 0;
+
+ if (spd == SPEED_100) {
+ if (dwmac->interface == PHY_INTERFACE_MODE_MII ||
+ dwmac->interface == PHY_INTERFACE_MODE_GMII) {
+ src = TX_RETIME_SRC_TXCLK;
+ } else if (dwmac->interface == PHY_INTERFACE_MODE_RMII) {
+ if (dwmac->ext_phyclk) {
+ src = TX_RETIME_SRC_PHYCLK;
+ } else {
+ src = TX_RETIME_SRC_CLKGEN;
+ freq = 50000000;
+ }
+
+ } else if (IS_PHY_IF_MODE_RGMII(dwmac->interface)) {
+ src = TX_RETIME_SRC_CLKGEN;
+ freq = 25000000;
+ }
+
+ if (src == TX_RETIME_SRC_CLKGEN && dwmac->clk)
+ clk_set_rate(dwmac->clk, freq);
+
+ } else if (spd == SPEED_1000) {
+ if (dwmac->is_tx_retime_src_clk_125)
+ src = TX_RETIME_SRC_CLK_125;
+ else
+ src = TX_RETIME_SRC_TXCLK;
+ }
+
+ regmap_update_bits(dwmac->regmap, dwmac->reg,
+ TX_RETIME_SRC_MASK, tx_retime_val[src]);
+}
+
+static void sti_dwmac_exit(struct platform_device *pdev, void *priv)
+{
+ struct sti_dwmac *dwmac = priv;
+
+ if (dwmac->clk)
+ clk_disable_unprepare(dwmac->clk);
+}
+
+static void sti_fix_mac_speed(void *priv, unsigned int spd)
+{
+ struct sti_dwmac *dwmac = priv;
+ setup_retime_src(dwmac, spd);
+ return;
+}
+
+static int sti_dwmac_parse_data(struct sti_dwmac *dwmac,
+ struct platform_device *pdev)
+{
+ struct resource *res;
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct regmap *regmap;
+ int err;
+
+ if (!np)
+ return -EINVAL;
+
+ res = platform_get_resource_byname(pdev,
+ IORESOURCE_MEM, "sti-ethconf");
+ if (!res)
+ return -ENODATA;
+
+ regmap = syscon_regmap_lookup_by_phandle(np, "st,syscon");
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ dwmac->dev = dev;
+ dwmac->interface = of_get_phy_mode(np);
+ dwmac->regmap = regmap;
+ dwmac->reg = res->start;
+ dwmac->ext_phyclk = of_property_read_bool(np, "st,ext-phyclk");
+
+ dwmac->is_tx_retime_src_clk_125 = false;
+
+ if (IS_PHY_IF_MODE_GBIT(dwmac->interface)) {
+ const char *rs;
+ err = of_property_read_string(np, "st,tx-retime-src", &rs);
+ if (err < 0) {
+ dev_err(dev, "st,tx-retime-src not specified\n");
+ return err;
+ }
+
+ if (!strcasecmp(rs, "clk_125"))
+ dwmac->is_tx_retime_src_clk_125 = true;
+
+ }
+
+ dwmac->clk = devm_clk_get(dev, "sti-ethclk");
+
+ if (IS_ERR(dwmac->clk))
+ dwmac->clk = NULL;
+
+ return 0;
+}
+
+static int sti_dwmac_init(struct platform_device *pdev, void *priv)
+{
+ struct sti_dwmac *dwmac = priv;
+ struct regmap *regmap = dwmac->regmap;
+ int iface = dwmac->interface;
+ u32 reg = dwmac->reg;
+ u32 val, spd;
+
+ if (dwmac->clk)
+ clk_prepare_enable(dwmac->clk);
+
+ regmap_update_bits(regmap, reg, MII_PHY_SEL_MASK,
+ phy_intf_sels[iface]);
+
+ val = (iface == PHY_INTERFACE_MODE_REVMII) ? 0 : ENMII;
+ regmap_update_bits(regmap, reg, ENMII_MASK, val);
+
+ if (IS_PHY_IF_MODE_GBIT(iface))
+ spd = SPEED_1000;
+ else
+ spd = SPEED_100;
+
+ setup_retime_src(dwmac, spd);
+
+ return 0;
+}
+
+static void *sti_dwmac_setup(struct platform_device *pdev)
+{
+ struct sti_dwmac *dwmac;
+ int ret;
+
+ dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
+ if (!dwmac)
+ return ERR_PTR(-ENOMEM);
+
+ ret = sti_dwmac_parse_data(dwmac, pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "Unable to parse OF data\n");
+ return ERR_PTR(ret);
+ }
+
+ return dwmac;
+}
+
+const struct stmmac_of_data sti_gmac_data = {
+ .fix_mac_speed = sti_fix_mac_speed,
+ .setup = sti_dwmac_setup,
+ .init = sti_dwmac_init,
+ .exit = sti_dwmac_exit,
+};
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index d9af26e..f9e60d7 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -133,6 +133,9 @@ bool stmmac_eee_init(struct stmmac_priv *priv);
#ifdef CONFIG_DWMAC_SUNXI
extern const struct stmmac_of_data sun7i_gmac_data;
#endif
+#ifdef CONFIG_DWMAC_STI
+extern const struct stmmac_of_data sti_gmac_data;
+#endif
extern struct platform_driver stmmac_pltfr_driver;
static inline int stmmac_register_platform(void)
{
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index 5884a7d..c61bc72b 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -33,6 +33,11 @@ static const struct of_device_id stmmac_dt_ids[] = {
#ifdef CONFIG_DWMAC_SUNXI
{ .compatible = "allwinner,sun7i-a20-gmac", .data = &sun7i_gmac_data},
#endif
+#ifdef CONFIG_DWMAC_STI
+ { .compatible = "st,stih415-dwmac", .data = &sti_gmac_data},
+ { .compatible = "st,stih416-dwmac", .data = &sti_gmac_data},
+ { .compatible = "st,stih127-dwmac", .data = &sti_gmac_data},
+#endif
/* SoC specific glue layers should come before generic bindings */
{ .compatible = "st,spear600-gmac"},
{ .compatible = "snps,dwmac-3.610"},
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v1 2/3] ARM: STi: Add STiH415 ethernet support.
2014-02-03 11:59 [PATCH v1 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
2014-02-03 12:01 ` [PATCH v1 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
@ 2014-02-03 12:01 ` srinivas.kandagatla
2014-02-03 12:02 ` [PATCH v1 3/3] ARM: STi: Add STiH416 " srinivas.kandagatla
2014-02-07 10:54 ` [PATCH v2 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
3 siblings, 0 replies; 17+ messages in thread
From: srinivas.kandagatla @ 2014-02-03 12:01 UTC (permalink / raw)
To: netdev
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Russell King, Srinivas Kandagatla, Stuart Menefy,
Giuseppe Cavallaro, devicetree, linux-doc, linux-kernel,
linux-arm-kernel, kernel, davem
From: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch adds support to STiH415 SOC, which has two ethernet
snps,dwmac controllers version 3.610. With this patch B2000 and B2020
boards can boot with ethernet in MII and RGMII modes.
Tested on both B2020 and B2000.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
---
arch/arm/boot/dts/stih415-clock.dtsi | 14 ++++
arch/arm/boot/dts/stih415-pinctrl.dtsi | 121 ++++++++++++++++++++++++++++++++
arch/arm/boot/dts/stih415.dtsi | 48 +++++++++++++
arch/arm/boot/dts/stih41x-b2000.dtsi | 22 ++++++
arch/arm/boot/dts/stih41x-b2020.dtsi | 26 +++++++
5 files changed, 231 insertions(+)
diff --git a/arch/arm/boot/dts/stih415-clock.dtsi b/arch/arm/boot/dts/stih415-clock.dtsi
index 174c799..d047dbc 100644
--- a/arch/arm/boot/dts/stih415-clock.dtsi
+++ b/arch/arm/boot/dts/stih415-clock.dtsi
@@ -34,5 +34,19 @@
compatible = "fixed-clock";
clock-frequency = <100000000>;
};
+
+ CLKS_GMAC0_PHY: clockgenA1@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLKS_GMAC0_PHY";
+ };
+
+ CLKS_ETH1_PHY: clockgenA0@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLKS_ETH1_PHY";
+ };
};
};
diff --git a/arch/arm/boot/dts/stih415-pinctrl.dtsi b/arch/arm/boot/dts/stih415-pinctrl.dtsi
index 887c5e5..9ca20aa 100644
--- a/arch/arm/boot/dts/stih415-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih415-pinctrl.dtsi
@@ -119,6 +119,56 @@
};
};
};
+
+ gmac1 {
+ pinctrl_mii1: mii1 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+ col = <&PIO0 7 ALT1 IN BYPASS 1000>;
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
+ mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
+ rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT1 IN NICLK 1000 CLK_A>;
+ };
+ };
+
+ pinctrl_rgmii1: rgmii1-0 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT DE_IO 1000 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ rxd0 = <&PIO1 4 ALT1 IN DE_IO 0 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN DE_IO 0 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN DE_IO 0 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN DE_IO 0 CLK_A>;
+
+ rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
+
+ clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
+ };
+ };
+ };
};
pin-controller-front {
@@ -284,6 +334,77 @@
};
};
};
+
+ gmac0{
+ pinctrl_mii0: mii0 {
+ st,pins {
+ mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
+ txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+
+ txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
+ col = <&PIO15 3 ALT2 IN BYPASS 1000>;
+ mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO13 5 ALT2 OUT NICLK 1000 CLK_A>;
+
+ };
+ };
+
+ pinctrl_gmii0: gmii0 {
+ st,pins {
+ mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
+ mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+ txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+
+ txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd4 = <&PIO14 4 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd5 = <&PIO14 5 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd6 = <&PIO14 6 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd7 = <&PIO14 7 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
+ col = <&PIO15 3 ALT2 IN BYPASS 1000>;
+ rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+
+ rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd4 = <&PIO16 4 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd5 = <&PIO16 5 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd6 = <&PIO16 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd7 = <&PIO16 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+
+ rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+ clk125 = <&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
+
+
+ };
+ };
+ };
};
pin-controller-left {
diff --git a/arch/arm/boot/dts/stih415.dtsi b/arch/arm/boot/dts/stih415.dtsi
index d52207c..cc9b22b 100644
--- a/arch/arm/boot/dts/stih415.dtsi
+++ b/arch/arm/boot/dts/stih415.dtsi
@@ -147,5 +147,53 @@
status = "disabled";
};
+
+ ethernet0: dwmac@fe810000 {
+ device_type = "network";
+ compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610";
+ status = "disabled";
+
+ reg = <0xfe810000 0x8000>, <0x148 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+
+ interrupts = <0 147 0>, <0 148 0>, <0 149 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+ resets = <&softreset STIH415_ETH0_SOFTRESET>;
+ reset-names = "stmmaceth";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+ snps,force_sf_dma_mode;
+
+ st,syscon = <&syscfg_rear>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii0>;
+ clock-names = "stmmaceth";
+ clocks = <&CLKS_GMAC0_PHY>;
+ };
+
+ ethernet1: dwmac@fef08000 {
+ device_type = "network";
+ compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610";
+ status = "disabled";
+ reg = <0xfef08000 0x8000>, <0x74 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+ interrupts = <0 150 0>, <0 151 0>, <0 152 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+ snps,force_sf_dma_mode;
+
+ st,syscon = <&syscfg_sbc>;
+
+ resets = <&softreset STIH415_ETH1_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii1>;
+ clock-names = "stmmaceth";
+ clocks = <&CLKS_ETH1_PHY>;
+ };
};
};
diff --git a/arch/arm/boot/dts/stih41x-b2000.dtsi b/arch/arm/boot/dts/stih41x-b2000.dtsi
index 1e6aa92..bf65c49 100644
--- a/arch/arm/boot/dts/stih41x-b2000.dtsi
+++ b/arch/arm/boot/dts/stih41x-b2000.dtsi
@@ -20,6 +20,8 @@
aliases {
ttyAS0 = &serial2;
+ ethernet0 = ðernet0;
+ ethernet1 = ðernet1;
};
soc {
@@ -46,5 +48,25 @@
status = "okay";
};
+
+ ethernet0: dwmac@fe810000 {
+ status = "okay";
+ phy-mode = "mii";
+ pinctrl-0 = <&pinctrl_mii0>;
+
+ snps,reset-gpio = <&PIO106 2>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 10000>;
+ };
+
+ ethernet1: dwmac@fef08000 {
+ status = "disabled";
+ phy-mode = "mii";
+ st,tx-retime-src = "txclk";
+
+ snps,reset-gpio = <&PIO4 7>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 10000>;
+ };
};
};
diff --git a/arch/arm/boot/dts/stih41x-b2020.dtsi b/arch/arm/boot/dts/stih41x-b2020.dtsi
index 0ef0a69..6c9a2ab 100644
--- a/arch/arm/boot/dts/stih41x-b2020.dtsi
+++ b/arch/arm/boot/dts/stih41x-b2020.dtsi
@@ -19,6 +19,7 @@
aliases {
ttyAS0 = &sbc_serial1;
+ ethernet1 = ðernet1;
};
soc {
sbc_serial1: serial@fe531000 {
@@ -60,5 +61,30 @@
i2c@fe541000 {
status = "okay";
};
+
+ /**
+ * ethernet clk routing:
+ * for
+ * max-speed = <1000>;
+ * set
+ * st,tx-retime-src = "clk_125";
+ *
+ * for
+ * max-speed = <100>;
+ * set
+ * st,tx-retime-src = "clkgen";
+ */
+
+ ethernet1: dwmac@fef08000 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ max-speed = <1000>;
+ st,tx-retime-src = "clk_125";
+ snps,reset-gpio = <&PIO3 0>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 10000>;
+
+ pinctrl-0 = <&pinctrl_rgmii1>;
+ };
};
};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v1 3/3] ARM: STi: Add STiH416 ethernet support.
2014-02-03 11:59 [PATCH v1 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
2014-02-03 12:01 ` [PATCH v1 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
2014-02-03 12:01 ` [PATCH v1 2/3] ARM: STi: Add STiH415 ethernet support srinivas.kandagatla
@ 2014-02-03 12:02 ` srinivas.kandagatla
2014-02-07 10:54 ` [PATCH v2 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
3 siblings, 0 replies; 17+ messages in thread
From: srinivas.kandagatla @ 2014-02-03 12:02 UTC (permalink / raw)
To: netdev
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Russell King, Srinivas Kandagatla, Stuart Menefy,
Giuseppe Cavallaro, devicetree, linux-doc, linux-kernel,
linux-arm-kernel, kernel, davem
From: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch adds support to STiH416 SOC, which has two ethernet
snps,dwmac controllers version 3.710. With this patch B2000 and B2020
boards can boot with ethernet in MII and RGMII modes.
Tested on both B2020 and B2000.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
---
arch/arm/boot/dts/stih416-clock.dtsi | 14 ++++
arch/arm/boot/dts/stih416-pinctrl.dtsi | 109 ++++++++++++++++++++++++++++++++
arch/arm/boot/dts/stih416.dtsi | 44 +++++++++++++
3 files changed, 167 insertions(+)
diff --git a/arch/arm/boot/dts/stih416-clock.dtsi b/arch/arm/boot/dts/stih416-clock.dtsi
index 7026bf1..a6942c7 100644
--- a/arch/arm/boot/dts/stih416-clock.dtsi
+++ b/arch/arm/boot/dts/stih416-clock.dtsi
@@ -37,5 +37,19 @@
clock-frequency = <100000000>;
clock-output-names = "CLK_S_ICN_REG_0";
};
+
+ CLK_S_GMAC0_PHY: clockgenA1@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLK_S_GMAC0_PHY";
+ };
+
+ CLK_S_ETH1_PHY: clockgenA0@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLK_S_ETH1_PHY";
+ };
};
};
diff --git a/arch/arm/boot/dts/stih416-pinctrl.dtsi b/arch/arm/boot/dts/stih416-pinctrl.dtsi
index 8863c38..c4beef2 100644
--- a/arch/arm/boot/dts/stih416-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih416-pinctrl.dtsi
@@ -132,6 +132,58 @@
};
};
};
+
+ gmac1 {
+ pinctrl_mii1: mii1 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+ col = <&PIO0 7 ALT1 IN BYPASS 1000>;
+
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 1500>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
+ mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
+ rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+
+ rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT1 OUT NICLK 0 CLK_A>;
+ };
+ };
+ pinctrl_rgmii1: rgmii1-0 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT DE_IO 500 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT DE_IO 500 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT DE_IO 500 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT DE_IO 500 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ rxd0 = <&PIO1 4 ALT1 IN DE_IO 500 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN DE_IO 500 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN DE_IO 500 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN DE_IO 500 CLK_A>;
+
+ rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
+
+ clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
+ };
+ };
+ };
};
pin-controller-front {
@@ -322,6 +374,63 @@
};
};
};
+
+ gmac0 {
+ pinctrl_mii0: mii0 {
+ st,pins {
+ mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
+ txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
+ col = <&PIO15 3 ALT2 IN BYPASS 1000>;
+ mdio= <&PIO15 4 ALT2 OUT BYPASS 1500>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO13 5 ALT2 OUT NICLK 0 CLK_B>;
+ };
+ };
+
+ pinctrl_gmii0: gmii0 {
+ st,pins {
+ };
+ };
+ pinctrl_rgmii0: rgmii0 {
+ st,pins {
+ phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
+ txen = <&PIO13 7 ALT2 OUT DE_IO 0 CLK_A>;
+ txd0 = <&PIO14 0 ALT2 OUT DE_IO 500 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT DE_IO 500 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT DE_IO 500 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT DE_IO 500 CLK_B>;
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+
+ mdio = <&PIO15 4 ALT2 OUT BYPASS 0>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxdv = <&PIO15 6 ALT2 IN DE_IO 500 CLK_A>;
+ rxd0 =<&PIO16 0 ALT2 IN DE_IO 500 CLK_A>;
+ rxd1 =<&PIO16 1 ALT2 IN DE_IO 500 CLK_A>;
+ rxd2 =<&PIO16 2 ALT2 IN DE_IO 500 CLK_A>;
+ rxd3 =<&PIO16 3 ALT2 IN DE_IO 500 CLK_A>;
+ rxclk =<&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+
+ clk125=<&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
+ };
+ };
+ };
};
pin-controller-fvdp-fe {
diff --git a/arch/arm/boot/dts/stih416.dtsi b/arch/arm/boot/dts/stih416.dtsi
index 788ba5b..a96055b 100644
--- a/arch/arm/boot/dts/stih416.dtsi
+++ b/arch/arm/boot/dts/stih416.dtsi
@@ -156,5 +156,49 @@
status = "disabled";
};
+
+ ethernet0: dwmac@fe810000 {
+ device_type = "network";
+ compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+ status = "disabled";
+ reg = <0xfe810000 0x8000>, <0x8bc 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+
+ interrupts = <0 133 0>, <0 134 0>, <0 135 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+
+ st,syscon = <&syscfg_rear>;
+ resets = <&softreset STIH416_ETH0_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii0>;
+ clock-names = "stmmaceth";
+ clocks = <&CLK_S_GMAC0_PHY>;
+ };
+
+ ethernet1: dwmac@fef08000 {
+ device_type = "network";
+ compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+ status = "disabled";
+ reg = <0xfef08000 0x8000>, <0x7f0 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+ interrupts = <0 136 0>, <0 137 0>, <0 138 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+
+ st,syscon = <&syscfg_sbc>;
+
+ resets = <&softreset STIH416_ETH1_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii1>;
+ clock-names = "stmmaceth";
+ clocks = <&CLK_S_ETH1_PHY>;
+ };
};
};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* Re: [PATCH v1 1/3] net: stmmac:sti: Add STi SOC glue driver.
2014-02-03 12:01 ` [PATCH v1 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
@ 2014-02-07 3:53 ` David Miller
2014-02-07 7:54 ` srinivas kandagatla
0 siblings, 1 reply; 17+ messages in thread
From: David Miller @ 2014-02-07 3:53 UTC (permalink / raw)
To: srinivas.kandagatla
Cc: netdev, robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak,
rob, linux, stuart.menefy, peppe.cavallaro, devicetree,
linux-doc, linux-kernel, linux-arm-kernel, kernel
From: <srinivas.kandagatla@st.com>
Date: Mon, 3 Feb 2014 12:01:08 +0000
> + res = platform_get_resource_byname(pdev,
> + IORESOURCE_MEM, "sti-ethconf");
This is not the correct way to format multi-line function calls,
you'll need to fix this up in this entire series.
The arguments on the second and subsequent lines must start at
the first column after the openning parenthesis of the function
call. You must use the appropriate number of both space and
TAB characters necessary to do so.
If you're only using TAB characters to indent, you're doing it
wrong.
Thank you.
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v1 1/3] net: stmmac:sti: Add STi SOC glue driver.
2014-02-07 3:53 ` David Miller
@ 2014-02-07 7:54 ` srinivas kandagatla
0 siblings, 0 replies; 17+ messages in thread
From: srinivas kandagatla @ 2014-02-07 7:54 UTC (permalink / raw)
To: David Miller
Cc: netdev, robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak,
rob, linux, stuart.menefy, peppe.cavallaro, devicetree,
linux-doc, linux-kernel, linux-arm-kernel, kernel
Thankyou Dave,
On 07/02/14 03:53, David Miller wrote:
> From: <srinivas.kandagatla@st.com>
> Date: Mon, 3 Feb 2014 12:01:08 +0000
>
>> + res = platform_get_resource_byname(pdev,
>> + IORESOURCE_MEM, "sti-ethconf");
>
> This is not the correct way to format multi-line function calls,
> you'll need to fix this up in this entire series.
I will fix this in next version.
>
> The arguments on the second and subsequent lines must start at
> the first column after the openning parenthesis of the function
> call. You must use the appropriate number of both space and
> TAB characters necessary to do so.
>
> If you're only using TAB characters to indent, you're doing it
> wrong.
>
> Thank you.
>
>
Thanks,
srini
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH v2 0/3] net: stmmac: Add STi GMAC ethernet
2014-02-03 11:59 [PATCH v1 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
` (2 preceding siblings ...)
2014-02-03 12:02 ` [PATCH v1 3/3] ARM: STi: Add STiH416 " srinivas.kandagatla
@ 2014-02-07 10:54 ` srinivas.kandagatla
2014-02-07 10:55 ` [PATCH v2 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
` (3 more replies)
3 siblings, 4 replies; 17+ messages in thread
From: srinivas.kandagatla @ 2014-02-07 10:54 UTC (permalink / raw)
To: netdev
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Russell King, Srinivas Kandagatla, Stuart Menefy,
Giuseppe Cavallaro, devicetree, linux-doc, linux-kernel,
linux-arm-kernel, kernel, davem
From: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Hi All,
This patch series adds Ethernet support to STi series SOCs STiH415 and STiH416.
STi SOC series integrates dwmac IP from synopsis, however there is a hardware
glue on top of this standard IP, this glue needs to configured before the
actual dwmac can be used. Also the glue logic needs re-configuring when the
link speed changes, This is because the clk source can change as the link
speed changes.
This patch just adds STi specific callbacks into of_data for configuring the
glue layer.
I have rebased my original patches (http://lkml.org/lkml/2013/11/12/243)
to latest stmmac which updates callbacks to suit glue drivers like this.
These patches are tested on b2000 and B2020 with STiH415 and STiH416.
Changes since v1:
- fixed multi-line function call format as suggested by David Miller.
Dave, Can I request you to take the first patch via net tree for v3.15, I can
request Arnd or Olof to take the DT patches via the arm-soc tree for v3.15.
Thanks,
srini
Srinivas Kandagatla (3):
net: stmmac:sti: Add STi SOC glue driver.
ARM: STi: Add STiH415 ethernet support.
ARM: STi: Add STiH416 ethernet support.
.../devicetree/bindings/net/sti-dwmac.txt | 58 ++++
arch/arm/boot/dts/stih415-clock.dtsi | 14 +
arch/arm/boot/dts/stih415-pinctrl.dtsi | 121 +++++++
arch/arm/boot/dts/stih415.dtsi | 48 +++
arch/arm/boot/dts/stih416-clock.dtsi | 14 +
arch/arm/boot/dts/stih416-pinctrl.dtsi | 109 +++++++
arch/arm/boot/dts/stih416.dtsi | 44 +++
arch/arm/boot/dts/stih41x-b2000.dtsi | 22 ++
arch/arm/boot/dts/stih41x-b2020.dtsi | 26 ++
drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 +
drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c | 331 ++++++++++++++++++++
drivers/net/ethernet/stmicro/stmmac/stmmac.h | 3 +
.../net/ethernet/stmicro/stmmac/stmmac_platform.c | 5 +
14 files changed, 807 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/sti-dwmac.txt
create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c
--
1.7.9.5
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH v2 1/3] net: stmmac:sti: Add STi SOC glue driver.
2014-02-07 10:54 ` [PATCH v2 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
@ 2014-02-07 10:55 ` srinivas.kandagatla
2014-02-10 22:40 ` David Miller
2014-02-07 10:55 ` [PATCH v2 2/3] ARM: STi: Add STiH415 ethernet support srinivas.kandagatla
` (2 subsequent siblings)
3 siblings, 1 reply; 17+ messages in thread
From: srinivas.kandagatla @ 2014-02-07 10:55 UTC (permalink / raw)
To: netdev
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Russell King, Srinivas Kandagatla, Stuart Menefy,
Giuseppe Cavallaro, devicetree, linux-doc, linux-kernel,
linux-arm-kernel, kernel, davem
From: Srinivas Kandagatla <srinivas.kandagatla@st.com>
STi series SOCs have a glue layer on top of the synopsis gmac IP, this
glue layer needs to be configured before the gmac driver starts using
the IP.
This patch adds a support to this glue layer which is configured via
stmmac setup, init, exit callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
---
.../devicetree/bindings/net/sti-dwmac.txt | 58 ++++
drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 +
drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c | 331 ++++++++++++++++++++
drivers/net/ethernet/stmicro/stmmac/stmmac.h | 3 +
.../net/ethernet/stmicro/stmmac/stmmac_platform.c | 5 +
6 files changed, 409 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/sti-dwmac.txt
create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c
diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt
new file mode 100644
index 0000000..3dd3d0b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt
@@ -0,0 +1,58 @@
+STMicroelectronics SoC DWMAC glue layer controller
+
+The device node has following properties.
+
+Required properties:
+ - compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac" or
+ "st,stid127-dwmac".
+ - reg : Offset of the glue configuration register map in system
+ configuration regmap pointed by st,syscon property and size.
+
+ - reg-names : Should be "sti-ethconf".
+
+ - st,syscon : Should be phandle to system configuration node which
+ encompases this glue registers.
+
+ - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be
+ wired up in from different sources. One via TXCLK pin and other via CLK_125
+ pin. This wiring is totally board dependent. However the retiming glue
+ logic should be configured accordingly. Possible values for this property
+
+ "txclk" - if 125Mhz clock is wired up via txclk line.
+ "clk_125" - if 125Mhz clock is wired up via clk_125 line.
+
+ This property is only valid for Giga bit setup( GMII, RGMII), and it is
+ un-used for non-giga bit (MII and RMII) setups. Also note that internal
+ clockgen can not generate stable 125Mhz clock.
+
+ - st,ext-phyclk: This boolean property indicates who is generating the clock
+ for tx and rx. This property is only valid for RMII case where the clock can
+ be generated from the MAC or PHY.
+
+ - clock-names: should be "sti-ethclk".
+ - clocks: Should point to ethernet clockgen which can generate phyclk.
+
+
+Example:
+
+ethernet0: dwmac@fe810000 {
+ device_type = "network";
+ compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+ reg = <0xfe810000 0x8000>, <0x8bc 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+ interrupts = <0 133 0>, <0 134 0>, <0 135 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+ phy-mode = "mii";
+
+ st,syscon = <&syscfg_rear>;
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+
+ resets = <&softreset STIH416_ETH0_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-0 = <&pinctrl_mii0>;
+ pinctrl-names = "default";
+ clocks = <&CLK_S_GMAC0_PHY>;
+ clock-names = "stmmaceth";
+};
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index e2f202e..f2d7c70 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -37,6 +37,17 @@ config DWMAC_SUNXI
stmmac device driver. This driver is used for A20/A31
GMAC ethernet controller.
+config DWMAC_STI
+ bool "STi GMAC support"
+ depends on STMMAC_PLATFORM && ARCH_STI
+ default y
+ ---help---
+ Support for ethernet controller on STi SOCs.
+
+ This selects STi SoC glue layer support for the stmmac
+ device driver. This driver is used on for the STi series
+ SOCs GMAC ethernet controller.
+
config STMMAC_PCI
bool "STMMAC PCI bus support"
depends on STMMAC_ETH && PCI
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index ecadece..dcef287 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -2,6 +2,7 @@ obj-$(CONFIG_STMMAC_ETH) += stmmac.o
stmmac-$(CONFIG_STMMAC_PLATFORM) += stmmac_platform.o
stmmac-$(CONFIG_STMMAC_PCI) += stmmac_pci.o
stmmac-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o
+stmmac-$(CONFIG_DWMAC_STI) += dwmac-sti.o
stmmac-objs:= stmmac_main.o stmmac_ethtool.o stmmac_mdio.o ring_mode.o \
chain_mode.o dwmac_lib.o dwmac1000_core.o dwmac1000_dma.o \
dwmac100_core.o dwmac100_dma.o enh_desc.o norm_desc.o \
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c
new file mode 100644
index 0000000..47113c2
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c
@@ -0,0 +1,331 @@
+/**
+ * dwmac-sti.c - STMicroelectronics DWMAC Specific Glue layer
+ *
+ * Copyright (C) 2003-2014 STMicroelectronics (R&D) Limited
+ * Author: Srinivas Kandagatla <srinivas.kandagatla@st.com>
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/stmmac.h>
+#include <linux/phy.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+
+/**
+ * STi GMAC glue logic.
+ * --------------------
+ *
+ * _
+ * | \
+ * --------|0 \ ETH_SEL_INTERNAL_NOTEXT_PHYCLK
+ * phyclk | |___________________________________________
+ * | | | (phyclk-in)
+ * --------|1 / |
+ * int-clk |_ / |
+ * | _
+ * | | \
+ * |_______|0 \ ETH_SEL_TX_RETIME_CLK
+ * | |___________________________
+ * | | (tx-retime-clk)
+ * _______|1 /
+ * | |_ /
+ * _ |
+ * | \ |
+ * --------|0 \ |
+ * clk_125 | |__|
+ * | | ETH_SEL_TXCLK_NOT_CLK125
+ * --------|1 /
+ * txclk |_ /
+ *
+ *
+ * ETH_SEL_INTERNAL_NOTEXT_PHYCLK is valid only for RMII where PHY can
+ * generate 50MHz clock or MAC can generate it.
+ * This bit is configured by "st,ext-phyclk" property.
+ *
+ * ETH_SEL_TXCLK_NOT_CLK125 is only valid for gigabit modes, where the 125Mhz
+ * clock either comes from clk-125 pin or txclk pin. This configuration is
+ * totally driven by the board wiring. This bit is configured by
+ * "st,tx-retime-src" property.
+ *
+ * TXCLK configuration is different for different phy interface modes
+ * and changes according to link speed in modes like RGMII.
+ *
+ * Below table summarizes the clock requirement and clock sources for
+ * supported phy interface modes with link speeds.
+ * ________________________________________________
+ *| PHY_MODE | 1000 Mbit Link | 100 Mbit Link |
+ * ------------------------------------------------
+ *| MII | n/a | 25Mhz |
+ *| | | txclk |
+ * ------------------------------------------------
+ *| GMII | 125Mhz | 25Mhz |
+ *| | clk-125/txclk | txclk |
+ * ------------------------------------------------
+ *| RGMII | 125Mhz | 25Mhz |
+ *| | clk-125/txclk | clkgen |
+ * ------------------------------------------------
+ *| RMII | n/a | 25Mhz |
+ *| | |clkgen/phyclk-in |
+ * ------------------------------------------------
+ *
+ * TX lines are always retimed with a clk, which can vary depending
+ * on the board configuration. Below is the table of these bits
+ * in eth configuration register depending on source of retime clk.
+ *
+ *---------------------------------------------------------------
+ * src | tx_rt_clk | int_not_ext_phyclk | txclk_n_clk125|
+ *---------------------------------------------------------------
+ * txclk | 0 | n/a | 1 |
+ *---------------------------------------------------------------
+ * ck_125| 0 | n/a | 0 |
+ *---------------------------------------------------------------
+ * phyclk| 1 | 0 | n/a |
+ *---------------------------------------------------------------
+ * clkgen| 1 | 1 | n/a |
+ *---------------------------------------------------------------
+ */
+
+ /* Register definition */
+
+ /* 3 bits [8:6]
+ * [6:6] ETH_SEL_TXCLK_NOT_CLK125
+ * [7:7] ETH_SEL_INTERNAL_NOTEXT_PHYCLK
+ * [8:8] ETH_SEL_TX_RETIME_CLK
+ *
+ */
+
+#define TX_RETIME_SRC_MASK GENMASK(8, 6)
+#define ETH_SEL_TX_RETIME_CLK BIT(8)
+#define ETH_SEL_INTERNAL_NOTEXT_PHYCLK BIT(7)
+#define ETH_SEL_TXCLK_NOT_CLK125 BIT(6)
+
+#define ENMII_MASK GENMASK(5, 5)
+#define ENMII BIT(5)
+
+/**
+ * 3 bits [4:2]
+ * 000-GMII/MII
+ * 001-RGMII
+ * 010-SGMII
+ * 100-RMII
+*/
+#define MII_PHY_SEL_MASK GENMASK(4, 2)
+#define ETH_PHY_SEL_RMII BIT(4)
+#define ETH_PHY_SEL_SGMII BIT(3)
+#define ETH_PHY_SEL_RGMII BIT(2)
+#define ETH_PHY_SEL_GMII 0x0
+#define ETH_PHY_SEL_MII 0x0
+
+#define IS_PHY_IF_MODE_RGMII(iface) (iface == PHY_INTERFACE_MODE_RGMII || \
+ iface == PHY_INTERFACE_MODE_RGMII_ID || \
+ iface == PHY_INTERFACE_MODE_RGMII_RXID || \
+ iface == PHY_INTERFACE_MODE_RGMII_TXID)
+
+#define IS_PHY_IF_MODE_GBIT(iface) (IS_PHY_IF_MODE_RGMII(iface) || \
+ iface == PHY_INTERFACE_MODE_GMII)
+
+struct sti_dwmac {
+ int interface;
+ bool ext_phyclk;
+ bool is_tx_retime_src_clk_125;
+ struct clk *clk;
+ int reg;
+ struct device *dev;
+ struct regmap *regmap;
+};
+
+static u32 phy_intf_sels[] = {
+ [PHY_INTERFACE_MODE_MII] = ETH_PHY_SEL_MII,
+ [PHY_INTERFACE_MODE_GMII] = ETH_PHY_SEL_GMII,
+ [PHY_INTERFACE_MODE_RGMII] = ETH_PHY_SEL_RGMII,
+ [PHY_INTERFACE_MODE_RGMII_ID] = ETH_PHY_SEL_RGMII,
+ [PHY_INTERFACE_MODE_SGMII] = ETH_PHY_SEL_SGMII,
+ [PHY_INTERFACE_MODE_RMII] = ETH_PHY_SEL_RMII,
+};
+
+enum {
+ TX_RETIME_SRC_NA = 0,
+ TX_RETIME_SRC_TXCLK = 1,
+ TX_RETIME_SRC_CLK_125,
+ TX_RETIME_SRC_PHYCLK,
+ TX_RETIME_SRC_CLKGEN,
+};
+
+static const char * const tx_retime_srcs[] = {
+ [TX_RETIME_SRC_NA] = "",
+ [TX_RETIME_SRC_TXCLK] = "txclk",
+ [TX_RETIME_SRC_CLK_125] = "clk_125",
+ [TX_RETIME_SRC_PHYCLK] = "phyclk",
+ [TX_RETIME_SRC_CLKGEN] = "clkgen",
+};
+
+static u32 tx_retime_val[] = {
+ [TX_RETIME_SRC_TXCLK] = ETH_SEL_TXCLK_NOT_CLK125,
+ [TX_RETIME_SRC_CLK_125] = 0x0,
+ [TX_RETIME_SRC_PHYCLK] = ETH_SEL_TX_RETIME_CLK,
+ [TX_RETIME_SRC_CLKGEN] = ETH_SEL_TX_RETIME_CLK |
+ ETH_SEL_INTERNAL_NOTEXT_PHYCLK,
+};
+
+static void setup_retime_src(struct sti_dwmac *dwmac, u32 spd)
+{
+ u32 src = 0, freq = 0;
+
+ if (spd == SPEED_100) {
+ if (dwmac->interface == PHY_INTERFACE_MODE_MII ||
+ dwmac->interface == PHY_INTERFACE_MODE_GMII) {
+ src = TX_RETIME_SRC_TXCLK;
+ } else if (dwmac->interface == PHY_INTERFACE_MODE_RMII) {
+ if (dwmac->ext_phyclk) {
+ src = TX_RETIME_SRC_PHYCLK;
+ } else {
+ src = TX_RETIME_SRC_CLKGEN;
+ freq = 50000000;
+ }
+
+ } else if (IS_PHY_IF_MODE_RGMII(dwmac->interface)) {
+ src = TX_RETIME_SRC_CLKGEN;
+ freq = 25000000;
+ }
+
+ if (src == TX_RETIME_SRC_CLKGEN && dwmac->clk)
+ clk_set_rate(dwmac->clk, freq);
+
+ } else if (spd == SPEED_1000) {
+ if (dwmac->is_tx_retime_src_clk_125)
+ src = TX_RETIME_SRC_CLK_125;
+ else
+ src = TX_RETIME_SRC_TXCLK;
+ }
+
+ regmap_update_bits(dwmac->regmap, dwmac->reg,
+ TX_RETIME_SRC_MASK, tx_retime_val[src]);
+}
+
+static void sti_dwmac_exit(struct platform_device *pdev, void *priv)
+{
+ struct sti_dwmac *dwmac = priv;
+
+ if (dwmac->clk)
+ clk_disable_unprepare(dwmac->clk);
+}
+
+static void sti_fix_mac_speed(void *priv, unsigned int spd)
+{
+ struct sti_dwmac *dwmac = priv;
+ setup_retime_src(dwmac, spd);
+ return;
+}
+
+static int sti_dwmac_parse_data(struct sti_dwmac *dwmac,
+ struct platform_device *pdev)
+{
+ struct resource *res;
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct regmap *regmap;
+ int err;
+
+ if (!np)
+ return -EINVAL;
+
+ res = platform_get_resource_byname(pdev,
+ IORESOURCE_MEM, "sti-ethconf");
+ if (!res)
+ return -ENODATA;
+
+ regmap = syscon_regmap_lookup_by_phandle(np, "st,syscon");
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ dwmac->dev = dev;
+ dwmac->interface = of_get_phy_mode(np);
+ dwmac->regmap = regmap;
+ dwmac->reg = res->start;
+ dwmac->ext_phyclk = of_property_read_bool(np, "st,ext-phyclk");
+
+ dwmac->is_tx_retime_src_clk_125 = false;
+
+ if (IS_PHY_IF_MODE_GBIT(dwmac->interface)) {
+ const char *rs;
+ err = of_property_read_string(np, "st,tx-retime-src", &rs);
+ if (err < 0) {
+ dev_err(dev, "st,tx-retime-src not specified\n");
+ return err;
+ }
+
+ if (!strcasecmp(rs, "clk_125"))
+ dwmac->is_tx_retime_src_clk_125 = true;
+
+ }
+
+ dwmac->clk = devm_clk_get(dev, "sti-ethclk");
+
+ if (IS_ERR(dwmac->clk))
+ dwmac->clk = NULL;
+
+ return 0;
+}
+
+static int sti_dwmac_init(struct platform_device *pdev, void *priv)
+{
+ struct sti_dwmac *dwmac = priv;
+ struct regmap *regmap = dwmac->regmap;
+ int iface = dwmac->interface;
+ u32 reg = dwmac->reg;
+ u32 val, spd;
+
+ if (dwmac->clk)
+ clk_prepare_enable(dwmac->clk);
+
+ regmap_update_bits(regmap, reg, MII_PHY_SEL_MASK,
+ phy_intf_sels[iface]);
+
+ val = (iface == PHY_INTERFACE_MODE_REVMII) ? 0 : ENMII;
+ regmap_update_bits(regmap, reg, ENMII_MASK, val);
+
+ if (IS_PHY_IF_MODE_GBIT(iface))
+ spd = SPEED_1000;
+ else
+ spd = SPEED_100;
+
+ setup_retime_src(dwmac, spd);
+
+ return 0;
+}
+
+static void *sti_dwmac_setup(struct platform_device *pdev)
+{
+ struct sti_dwmac *dwmac;
+ int ret;
+
+ dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
+ if (!dwmac)
+ return ERR_PTR(-ENOMEM);
+
+ ret = sti_dwmac_parse_data(dwmac, pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "Unable to parse OF data\n");
+ return ERR_PTR(ret);
+ }
+
+ return dwmac;
+}
+
+const struct stmmac_of_data sti_gmac_data = {
+ .fix_mac_speed = sti_fix_mac_speed,
+ .setup = sti_dwmac_setup,
+ .init = sti_dwmac_init,
+ .exit = sti_dwmac_exit,
+};
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index d9af26e..f9e60d7 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -133,6 +133,9 @@ bool stmmac_eee_init(struct stmmac_priv *priv);
#ifdef CONFIG_DWMAC_SUNXI
extern const struct stmmac_of_data sun7i_gmac_data;
#endif
+#ifdef CONFIG_DWMAC_STI
+extern const struct stmmac_of_data sti_gmac_data;
+#endif
extern struct platform_driver stmmac_pltfr_driver;
static inline int stmmac_register_platform(void)
{
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index 5884a7d..c61bc72b 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -33,6 +33,11 @@ static const struct of_device_id stmmac_dt_ids[] = {
#ifdef CONFIG_DWMAC_SUNXI
{ .compatible = "allwinner,sun7i-a20-gmac", .data = &sun7i_gmac_data},
#endif
+#ifdef CONFIG_DWMAC_STI
+ { .compatible = "st,stih415-dwmac", .data = &sti_gmac_data},
+ { .compatible = "st,stih416-dwmac", .data = &sti_gmac_data},
+ { .compatible = "st,stih127-dwmac", .data = &sti_gmac_data},
+#endif
/* SoC specific glue layers should come before generic bindings */
{ .compatible = "st,spear600-gmac"},
{ .compatible = "snps,dwmac-3.610"},
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v2 2/3] ARM: STi: Add STiH415 ethernet support.
2014-02-07 10:54 ` [PATCH v2 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
2014-02-07 10:55 ` [PATCH v2 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
@ 2014-02-07 10:55 ` srinivas.kandagatla
2014-02-07 10:55 ` [PATCH v2 3/3] ARM: STi: Add STiH416 " srinivas.kandagatla
2014-02-11 9:58 ` [PATCH v3 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
3 siblings, 0 replies; 17+ messages in thread
From: srinivas.kandagatla @ 2014-02-07 10:55 UTC (permalink / raw)
To: netdev
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Russell King, Srinivas Kandagatla, Stuart Menefy,
Giuseppe Cavallaro, devicetree, linux-doc, linux-kernel,
linux-arm-kernel, kernel, davem
From: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch adds support to STiH415 SOC, which has two ethernet
snps,dwmac controllers version 3.610. With this patch B2000 and B2020
boards can boot with ethernet in MII and RGMII modes.
Tested on both B2020 and B2000.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
---
arch/arm/boot/dts/stih415-clock.dtsi | 14 ++++
arch/arm/boot/dts/stih415-pinctrl.dtsi | 121 ++++++++++++++++++++++++++++++++
arch/arm/boot/dts/stih415.dtsi | 48 +++++++++++++
arch/arm/boot/dts/stih41x-b2000.dtsi | 22 ++++++
arch/arm/boot/dts/stih41x-b2020.dtsi | 26 +++++++
5 files changed, 231 insertions(+)
diff --git a/arch/arm/boot/dts/stih415-clock.dtsi b/arch/arm/boot/dts/stih415-clock.dtsi
index 174c799..d047dbc 100644
--- a/arch/arm/boot/dts/stih415-clock.dtsi
+++ b/arch/arm/boot/dts/stih415-clock.dtsi
@@ -34,5 +34,19 @@
compatible = "fixed-clock";
clock-frequency = <100000000>;
};
+
+ CLKS_GMAC0_PHY: clockgenA1@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLKS_GMAC0_PHY";
+ };
+
+ CLKS_ETH1_PHY: clockgenA0@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLKS_ETH1_PHY";
+ };
};
};
diff --git a/arch/arm/boot/dts/stih415-pinctrl.dtsi b/arch/arm/boot/dts/stih415-pinctrl.dtsi
index 887c5e5..9ca20aa 100644
--- a/arch/arm/boot/dts/stih415-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih415-pinctrl.dtsi
@@ -119,6 +119,56 @@
};
};
};
+
+ gmac1 {
+ pinctrl_mii1: mii1 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+ col = <&PIO0 7 ALT1 IN BYPASS 1000>;
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
+ mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
+ rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT1 IN NICLK 1000 CLK_A>;
+ };
+ };
+
+ pinctrl_rgmii1: rgmii1-0 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT DE_IO 1000 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ rxd0 = <&PIO1 4 ALT1 IN DE_IO 0 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN DE_IO 0 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN DE_IO 0 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN DE_IO 0 CLK_A>;
+
+ rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
+
+ clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
+ };
+ };
+ };
};
pin-controller-front {
@@ -284,6 +334,77 @@
};
};
};
+
+ gmac0{
+ pinctrl_mii0: mii0 {
+ st,pins {
+ mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
+ txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+
+ txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
+ col = <&PIO15 3 ALT2 IN BYPASS 1000>;
+ mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO13 5 ALT2 OUT NICLK 1000 CLK_A>;
+
+ };
+ };
+
+ pinctrl_gmii0: gmii0 {
+ st,pins {
+ mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
+ mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+ txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+
+ txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd4 = <&PIO14 4 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd5 = <&PIO14 5 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd6 = <&PIO14 6 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd7 = <&PIO14 7 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
+ col = <&PIO15 3 ALT2 IN BYPASS 1000>;
+ rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+
+ rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd4 = <&PIO16 4 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd5 = <&PIO16 5 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd6 = <&PIO16 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd7 = <&PIO16 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+
+ rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+ clk125 = <&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
+
+
+ };
+ };
+ };
};
pin-controller-left {
diff --git a/arch/arm/boot/dts/stih415.dtsi b/arch/arm/boot/dts/stih415.dtsi
index d52207c..cc9b22b 100644
--- a/arch/arm/boot/dts/stih415.dtsi
+++ b/arch/arm/boot/dts/stih415.dtsi
@@ -147,5 +147,53 @@
status = "disabled";
};
+
+ ethernet0: dwmac@fe810000 {
+ device_type = "network";
+ compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610";
+ status = "disabled";
+
+ reg = <0xfe810000 0x8000>, <0x148 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+
+ interrupts = <0 147 0>, <0 148 0>, <0 149 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+ resets = <&softreset STIH415_ETH0_SOFTRESET>;
+ reset-names = "stmmaceth";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+ snps,force_sf_dma_mode;
+
+ st,syscon = <&syscfg_rear>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii0>;
+ clock-names = "stmmaceth";
+ clocks = <&CLKS_GMAC0_PHY>;
+ };
+
+ ethernet1: dwmac@fef08000 {
+ device_type = "network";
+ compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610";
+ status = "disabled";
+ reg = <0xfef08000 0x8000>, <0x74 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+ interrupts = <0 150 0>, <0 151 0>, <0 152 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+ snps,force_sf_dma_mode;
+
+ st,syscon = <&syscfg_sbc>;
+
+ resets = <&softreset STIH415_ETH1_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii1>;
+ clock-names = "stmmaceth";
+ clocks = <&CLKS_ETH1_PHY>;
+ };
};
};
diff --git a/arch/arm/boot/dts/stih41x-b2000.dtsi b/arch/arm/boot/dts/stih41x-b2000.dtsi
index 1e6aa92..bf65c49 100644
--- a/arch/arm/boot/dts/stih41x-b2000.dtsi
+++ b/arch/arm/boot/dts/stih41x-b2000.dtsi
@@ -20,6 +20,8 @@
aliases {
ttyAS0 = &serial2;
+ ethernet0 = ðernet0;
+ ethernet1 = ðernet1;
};
soc {
@@ -46,5 +48,25 @@
status = "okay";
};
+
+ ethernet0: dwmac@fe810000 {
+ status = "okay";
+ phy-mode = "mii";
+ pinctrl-0 = <&pinctrl_mii0>;
+
+ snps,reset-gpio = <&PIO106 2>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 10000>;
+ };
+
+ ethernet1: dwmac@fef08000 {
+ status = "disabled";
+ phy-mode = "mii";
+ st,tx-retime-src = "txclk";
+
+ snps,reset-gpio = <&PIO4 7>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 10000>;
+ };
};
};
diff --git a/arch/arm/boot/dts/stih41x-b2020.dtsi b/arch/arm/boot/dts/stih41x-b2020.dtsi
index 0ef0a69..6c9a2ab 100644
--- a/arch/arm/boot/dts/stih41x-b2020.dtsi
+++ b/arch/arm/boot/dts/stih41x-b2020.dtsi
@@ -19,6 +19,7 @@
aliases {
ttyAS0 = &sbc_serial1;
+ ethernet1 = ðernet1;
};
soc {
sbc_serial1: serial@fe531000 {
@@ -60,5 +61,30 @@
i2c@fe541000 {
status = "okay";
};
+
+ /**
+ * ethernet clk routing:
+ * for
+ * max-speed = <1000>;
+ * set
+ * st,tx-retime-src = "clk_125";
+ *
+ * for
+ * max-speed = <100>;
+ * set
+ * st,tx-retime-src = "clkgen";
+ */
+
+ ethernet1: dwmac@fef08000 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ max-speed = <1000>;
+ st,tx-retime-src = "clk_125";
+ snps,reset-gpio = <&PIO3 0>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 10000>;
+
+ pinctrl-0 = <&pinctrl_rgmii1>;
+ };
};
};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v2 3/3] ARM: STi: Add STiH416 ethernet support.
2014-02-07 10:54 ` [PATCH v2 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
2014-02-07 10:55 ` [PATCH v2 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
2014-02-07 10:55 ` [PATCH v2 2/3] ARM: STi: Add STiH415 ethernet support srinivas.kandagatla
@ 2014-02-07 10:55 ` srinivas.kandagatla
2014-02-11 9:58 ` [PATCH v3 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
3 siblings, 0 replies; 17+ messages in thread
From: srinivas.kandagatla @ 2014-02-07 10:55 UTC (permalink / raw)
To: netdev
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Russell King, Srinivas Kandagatla, Stuart Menefy,
Giuseppe Cavallaro, devicetree, linux-doc, linux-kernel,
linux-arm-kernel, kernel, davem
From: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch adds support to STiH416 SOC, which has two ethernet
snps,dwmac controllers version 3.710. With this patch B2000 and B2020
boards can boot with ethernet in MII and RGMII modes.
Tested on both B2020 and B2000.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
---
arch/arm/boot/dts/stih416-clock.dtsi | 14 ++++
arch/arm/boot/dts/stih416-pinctrl.dtsi | 109 ++++++++++++++++++++++++++++++++
arch/arm/boot/dts/stih416.dtsi | 44 +++++++++++++
3 files changed, 167 insertions(+)
diff --git a/arch/arm/boot/dts/stih416-clock.dtsi b/arch/arm/boot/dts/stih416-clock.dtsi
index 7026bf1..a6942c7 100644
--- a/arch/arm/boot/dts/stih416-clock.dtsi
+++ b/arch/arm/boot/dts/stih416-clock.dtsi
@@ -37,5 +37,19 @@
clock-frequency = <100000000>;
clock-output-names = "CLK_S_ICN_REG_0";
};
+
+ CLK_S_GMAC0_PHY: clockgenA1@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLK_S_GMAC0_PHY";
+ };
+
+ CLK_S_ETH1_PHY: clockgenA0@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLK_S_ETH1_PHY";
+ };
};
};
diff --git a/arch/arm/boot/dts/stih416-pinctrl.dtsi b/arch/arm/boot/dts/stih416-pinctrl.dtsi
index 8863c38..c4beef2 100644
--- a/arch/arm/boot/dts/stih416-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih416-pinctrl.dtsi
@@ -132,6 +132,58 @@
};
};
};
+
+ gmac1 {
+ pinctrl_mii1: mii1 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+ col = <&PIO0 7 ALT1 IN BYPASS 1000>;
+
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 1500>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
+ mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
+ rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+
+ rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT1 OUT NICLK 0 CLK_A>;
+ };
+ };
+ pinctrl_rgmii1: rgmii1-0 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT DE_IO 500 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT DE_IO 500 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT DE_IO 500 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT DE_IO 500 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ rxd0 = <&PIO1 4 ALT1 IN DE_IO 500 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN DE_IO 500 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN DE_IO 500 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN DE_IO 500 CLK_A>;
+
+ rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
+
+ clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
+ };
+ };
+ };
};
pin-controller-front {
@@ -322,6 +374,63 @@
};
};
};
+
+ gmac0 {
+ pinctrl_mii0: mii0 {
+ st,pins {
+ mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
+ txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
+ col = <&PIO15 3 ALT2 IN BYPASS 1000>;
+ mdio= <&PIO15 4 ALT2 OUT BYPASS 1500>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO13 5 ALT2 OUT NICLK 0 CLK_B>;
+ };
+ };
+
+ pinctrl_gmii0: gmii0 {
+ st,pins {
+ };
+ };
+ pinctrl_rgmii0: rgmii0 {
+ st,pins {
+ phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
+ txen = <&PIO13 7 ALT2 OUT DE_IO 0 CLK_A>;
+ txd0 = <&PIO14 0 ALT2 OUT DE_IO 500 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT DE_IO 500 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT DE_IO 500 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT DE_IO 500 CLK_B>;
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+
+ mdio = <&PIO15 4 ALT2 OUT BYPASS 0>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxdv = <&PIO15 6 ALT2 IN DE_IO 500 CLK_A>;
+ rxd0 =<&PIO16 0 ALT2 IN DE_IO 500 CLK_A>;
+ rxd1 =<&PIO16 1 ALT2 IN DE_IO 500 CLK_A>;
+ rxd2 =<&PIO16 2 ALT2 IN DE_IO 500 CLK_A>;
+ rxd3 =<&PIO16 3 ALT2 IN DE_IO 500 CLK_A>;
+ rxclk =<&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+
+ clk125=<&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
+ };
+ };
+ };
};
pin-controller-fvdp-fe {
diff --git a/arch/arm/boot/dts/stih416.dtsi b/arch/arm/boot/dts/stih416.dtsi
index 788ba5b..a96055b 100644
--- a/arch/arm/boot/dts/stih416.dtsi
+++ b/arch/arm/boot/dts/stih416.dtsi
@@ -156,5 +156,49 @@
status = "disabled";
};
+
+ ethernet0: dwmac@fe810000 {
+ device_type = "network";
+ compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+ status = "disabled";
+ reg = <0xfe810000 0x8000>, <0x8bc 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+
+ interrupts = <0 133 0>, <0 134 0>, <0 135 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+
+ st,syscon = <&syscfg_rear>;
+ resets = <&softreset STIH416_ETH0_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii0>;
+ clock-names = "stmmaceth";
+ clocks = <&CLK_S_GMAC0_PHY>;
+ };
+
+ ethernet1: dwmac@fef08000 {
+ device_type = "network";
+ compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+ status = "disabled";
+ reg = <0xfef08000 0x8000>, <0x7f0 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+ interrupts = <0 136 0>, <0 137 0>, <0 138 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+
+ st,syscon = <&syscfg_sbc>;
+
+ resets = <&softreset STIH416_ETH1_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii1>;
+ clock-names = "stmmaceth";
+ clocks = <&CLK_S_ETH1_PHY>;
+ };
};
};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* Re: [PATCH v2 1/3] net: stmmac:sti: Add STi SOC glue driver.
2014-02-07 10:55 ` [PATCH v2 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
@ 2014-02-10 22:40 ` David Miller
2014-02-11 9:01 ` srinivas kandagatla
0 siblings, 1 reply; 17+ messages in thread
From: David Miller @ 2014-02-10 22:40 UTC (permalink / raw)
To: srinivas.kandagatla
Cc: netdev, robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak,
rob, linux, stuart.menefy, peppe.cavallaro, devicetree,
linux-doc, linux-kernel, linux-arm-kernel, kernel
From: <srinivas.kandagatla@st.com>
Date: Fri, 7 Feb 2014 10:55:25 +0000
> + if (dwmac->interface == PHY_INTERFACE_MODE_MII ||
> + dwmac->interface == PHY_INTERFACE_MODE_GMII) {
This is not indented correctly, the first character on the second line should
line up exactly at the column after the openning parenthesis on the first
line.
The objective is not to indent using only TAB characters, which you
are doing here.
Rather, the objective is to use the appropriate number of TAB _and_
space characters necessary to reach the proper column.
> + const char *rs;
> + err = of_property_read_string(np, "st,tx-retime-src", &rs);
Please add an empty line after the local variable declaration.
> + if (!strcasecmp(rs, "clk_125"))
> + dwmac->is_tx_retime_src_clk_125 = true;
> +
> + }
That empty line is superfluous, please delete it.
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v2 1/3] net: stmmac:sti: Add STi SOC glue driver.
2014-02-10 22:40 ` David Miller
@ 2014-02-11 9:01 ` srinivas kandagatla
0 siblings, 0 replies; 17+ messages in thread
From: srinivas kandagatla @ 2014-02-11 9:01 UTC (permalink / raw)
To: David Miller
Cc: netdev, robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak,
rob, linux, stuart.menefy, peppe.cavallaro, devicetree,
linux-doc, linux-kernel, linux-arm-kernel, kernel
Thankyou Dave,
I will fix these in next version.
On 10/02/14 22:40, David Miller wrote:
> From: <srinivas.kandagatla@st.com>
> Date: Fri, 7 Feb 2014 10:55:25 +0000
>
>> + if (dwmac->interface == PHY_INTERFACE_MODE_MII ||
>> + dwmac->interface == PHY_INTERFACE_MODE_GMII) {
>
> This is not indented correctly, the first character on the second line should
> line up exactly at the column after the openning parenthesis on the first
> line.
>
> The objective is not to indent using only TAB characters, which you
> are doing here.
>
> Rather, the objective is to use the appropriate number of TAB _and_
> space characters necessary to reach the proper column.
>
>> + const char *rs;
>> + err = of_property_read_string(np, "st,tx-retime-src", &rs);
>
> Please add an empty line after the local variable declaration.
>
>> + if (!strcasecmp(rs, "clk_125"))
>> + dwmac->is_tx_retime_src_clk_125 = true;
>> +
>> + }
>
> That empty line is superfluous, please delete it.
>
>
Thanks,
srini
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH v3 0/3] net: stmmac: Add STi GMAC ethernet
2014-02-07 10:54 ` [PATCH v2 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
` (2 preceding siblings ...)
2014-02-07 10:55 ` [PATCH v2 3/3] ARM: STi: Add STiH416 " srinivas.kandagatla
@ 2014-02-11 9:58 ` srinivas.kandagatla
2014-02-11 9:59 ` [PATCH v3 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
` (3 more replies)
3 siblings, 4 replies; 17+ messages in thread
From: srinivas.kandagatla @ 2014-02-11 9:58 UTC (permalink / raw)
To: netdev
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Russell King, Srinivas Kandagatla, Stuart Menefy,
Giuseppe Cavallaro, devicetree, linux-doc, linux-kernel,
linux-arm-kernel, kernel, davem
From: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Hi All,
This patch series adds Ethernet support to STi series SOCs STiH415 and STiH416.
STi SOC series integrates dwmac IP from synopsis, however there is a hardware
glue on top of this standard IP, this glue needs to configured before the
actual dwmac can be used. Also the glue logic needs re-configuring when the
link speed changes, This is because the clk source can change as the link
speed changes.
This patch just adds STi specific callbacks into of_data for configuring the
glue layer.
I have rebased my original patches (http://lkml.org/lkml/2013/11/12/243)
to latest stmmac which updates callbacks to suit glue drivers like this.
These patches are tested on b2000 and B2020 with STiH415 and STiH416.
Changes since v1:
- fixed multi-line function call format as suggested by David Miller.
Changes since v2:
- fix indenting issues & superfluous empty lines as suggested by David Miller.
- Run the code through scripts/Lindent.
Dave, Can I request you to take the first patch via net tree for v3.15, I can
request Arnd or Olof to take the DT patches via the arm-soc tree for v3.15.
Thanks,
srini
Srinivas Kandagatla (3):
net: stmmac:sti: Add STi SOC glue driver.
ARM: STi: Add STiH415 ethernet support.
ARM: STi: Add STiH416 ethernet support.
.../devicetree/bindings/net/sti-dwmac.txt | 58 ++++
arch/arm/boot/dts/stih415-clock.dtsi | 14 +
arch/arm/boot/dts/stih415-pinctrl.dtsi | 121 +++++++
arch/arm/boot/dts/stih415.dtsi | 48 +++
arch/arm/boot/dts/stih416-clock.dtsi | 14 +
arch/arm/boot/dts/stih416-pinctrl.dtsi | 109 +++++++
arch/arm/boot/dts/stih416.dtsi | 44 +++
arch/arm/boot/dts/stih41x-b2000.dtsi | 22 ++
arch/arm/boot/dts/stih41x-b2020.dtsi | 26 ++
drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 +
drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c | 330 ++++++++++++++++++++
drivers/net/ethernet/stmicro/stmmac/stmmac.h | 3 +
.../net/ethernet/stmicro/stmmac/stmmac_platform.c | 5 +
14 files changed, 806 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/sti-dwmac.txt
create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c
--
1.7.9.5
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH v3 1/3] net: stmmac:sti: Add STi SOC glue driver.
2014-02-11 9:58 ` [PATCH v3 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
@ 2014-02-11 9:59 ` srinivas.kandagatla
2014-02-11 10:00 ` [PATCH v3 2/3] ARM: STi: Add STiH415 ethernet support srinivas.kandagatla
` (2 subsequent siblings)
3 siblings, 0 replies; 17+ messages in thread
From: srinivas.kandagatla @ 2014-02-11 9:59 UTC (permalink / raw)
To: netdev
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Russell King, Srinivas Kandagatla, Stuart Menefy,
Giuseppe Cavallaro, devicetree, linux-doc, linux-kernel,
linux-arm-kernel, kernel, davem
From: Srinivas Kandagatla <srinivas.kandagatla@st.com>
STi series SOCs have a glue layer on top of the synopsis gmac IP, this
glue layer needs to be configured before the gmac driver starts using
the IP.
This patch adds a support to this glue layer which is configured via
stmmac setup, init, exit callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
---
.../devicetree/bindings/net/sti-dwmac.txt | 58 ++++
drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 +
drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c | 330 ++++++++++++++++++++
drivers/net/ethernet/stmicro/stmmac/stmmac.h | 3 +
.../net/ethernet/stmicro/stmmac/stmmac_platform.c | 5 +
6 files changed, 408 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/sti-dwmac.txt
create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c
diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt
new file mode 100644
index 0000000..3dd3d0b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt
@@ -0,0 +1,58 @@
+STMicroelectronics SoC DWMAC glue layer controller
+
+The device node has following properties.
+
+Required properties:
+ - compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac" or
+ "st,stid127-dwmac".
+ - reg : Offset of the glue configuration register map in system
+ configuration regmap pointed by st,syscon property and size.
+
+ - reg-names : Should be "sti-ethconf".
+
+ - st,syscon : Should be phandle to system configuration node which
+ encompases this glue registers.
+
+ - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be
+ wired up in from different sources. One via TXCLK pin and other via CLK_125
+ pin. This wiring is totally board dependent. However the retiming glue
+ logic should be configured accordingly. Possible values for this property
+
+ "txclk" - if 125Mhz clock is wired up via txclk line.
+ "clk_125" - if 125Mhz clock is wired up via clk_125 line.
+
+ This property is only valid for Giga bit setup( GMII, RGMII), and it is
+ un-used for non-giga bit (MII and RMII) setups. Also note that internal
+ clockgen can not generate stable 125Mhz clock.
+
+ - st,ext-phyclk: This boolean property indicates who is generating the clock
+ for tx and rx. This property is only valid for RMII case where the clock can
+ be generated from the MAC or PHY.
+
+ - clock-names: should be "sti-ethclk".
+ - clocks: Should point to ethernet clockgen which can generate phyclk.
+
+
+Example:
+
+ethernet0: dwmac@fe810000 {
+ device_type = "network";
+ compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+ reg = <0xfe810000 0x8000>, <0x8bc 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+ interrupts = <0 133 0>, <0 134 0>, <0 135 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+ phy-mode = "mii";
+
+ st,syscon = <&syscfg_rear>;
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+
+ resets = <&softreset STIH416_ETH0_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-0 = <&pinctrl_mii0>;
+ pinctrl-names = "default";
+ clocks = <&CLK_S_GMAC0_PHY>;
+ clock-names = "stmmaceth";
+};
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index e2f202e..f2d7c70 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -37,6 +37,17 @@ config DWMAC_SUNXI
stmmac device driver. This driver is used for A20/A31
GMAC ethernet controller.
+config DWMAC_STI
+ bool "STi GMAC support"
+ depends on STMMAC_PLATFORM && ARCH_STI
+ default y
+ ---help---
+ Support for ethernet controller on STi SOCs.
+
+ This selects STi SoC glue layer support for the stmmac
+ device driver. This driver is used on for the STi series
+ SOCs GMAC ethernet controller.
+
config STMMAC_PCI
bool "STMMAC PCI bus support"
depends on STMMAC_ETH && PCI
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index ecadece..dcef287 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -2,6 +2,7 @@ obj-$(CONFIG_STMMAC_ETH) += stmmac.o
stmmac-$(CONFIG_STMMAC_PLATFORM) += stmmac_platform.o
stmmac-$(CONFIG_STMMAC_PCI) += stmmac_pci.o
stmmac-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o
+stmmac-$(CONFIG_DWMAC_STI) += dwmac-sti.o
stmmac-objs:= stmmac_main.o stmmac_ethtool.o stmmac_mdio.o ring_mode.o \
chain_mode.o dwmac_lib.o dwmac1000_core.o dwmac1000_dma.o \
dwmac100_core.o dwmac100_dma.o enh_desc.o norm_desc.o \
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c
new file mode 100644
index 0000000..552bbc1
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c
@@ -0,0 +1,330 @@
+/**
+ * dwmac-sti.c - STMicroelectronics DWMAC Specific Glue layer
+ *
+ * Copyright (C) 2003-2014 STMicroelectronics (R&D) Limited
+ * Author: Srinivas Kandagatla <srinivas.kandagatla@st.com>
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/stmmac.h>
+#include <linux/phy.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+
+/**
+ * STi GMAC glue logic.
+ * --------------------
+ *
+ * _
+ * | \
+ * --------|0 \ ETH_SEL_INTERNAL_NOTEXT_PHYCLK
+ * phyclk | |___________________________________________
+ * | | | (phyclk-in)
+ * --------|1 / |
+ * int-clk |_ / |
+ * | _
+ * | | \
+ * |_______|1 \ ETH_SEL_TX_RETIME_CLK
+ * | |___________________________
+ * | | (tx-retime-clk)
+ * _______|0 /
+ * | |_ /
+ * _ |
+ * | \ |
+ * --------|0 \ |
+ * clk_125 | |__|
+ * | | ETH_SEL_TXCLK_NOT_CLK125
+ * --------|1 /
+ * txclk |_ /
+ *
+ *
+ * ETH_SEL_INTERNAL_NOTEXT_PHYCLK is valid only for RMII where PHY can
+ * generate 50MHz clock or MAC can generate it.
+ * This bit is configured by "st,ext-phyclk" property.
+ *
+ * ETH_SEL_TXCLK_NOT_CLK125 is only valid for gigabit modes, where the 125Mhz
+ * clock either comes from clk-125 pin or txclk pin. This configuration is
+ * totally driven by the board wiring. This bit is configured by
+ * "st,tx-retime-src" property.
+ *
+ * TXCLK configuration is different for different phy interface modes
+ * and changes according to link speed in modes like RGMII.
+ *
+ * Below table summarizes the clock requirement and clock sources for
+ * supported phy interface modes with link speeds.
+ * ________________________________________________
+ *| PHY_MODE | 1000 Mbit Link | 100 Mbit Link |
+ * ------------------------------------------------
+ *| MII | n/a | 25Mhz |
+ *| | | txclk |
+ * ------------------------------------------------
+ *| GMII | 125Mhz | 25Mhz |
+ *| | clk-125/txclk | txclk |
+ * ------------------------------------------------
+ *| RGMII | 125Mhz | 25Mhz |
+ *| | clk-125/txclk | clkgen |
+ * ------------------------------------------------
+ *| RMII | n/a | 25Mhz |
+ *| | |clkgen/phyclk-in |
+ * ------------------------------------------------
+ *
+ * TX lines are always retimed with a clk, which can vary depending
+ * on the board configuration. Below is the table of these bits
+ * in eth configuration register depending on source of retime clk.
+ *
+ *---------------------------------------------------------------
+ * src | tx_rt_clk | int_not_ext_phyclk | txclk_n_clk125|
+ *---------------------------------------------------------------
+ * txclk | 0 | n/a | 1 |
+ *---------------------------------------------------------------
+ * ck_125| 0 | n/a | 0 |
+ *---------------------------------------------------------------
+ * phyclk| 1 | 0 | n/a |
+ *---------------------------------------------------------------
+ * clkgen| 1 | 1 | n/a |
+ *---------------------------------------------------------------
+ */
+
+ /* Register definition */
+
+ /* 3 bits [8:6]
+ * [6:6] ETH_SEL_TXCLK_NOT_CLK125
+ * [7:7] ETH_SEL_INTERNAL_NOTEXT_PHYCLK
+ * [8:8] ETH_SEL_TX_RETIME_CLK
+ *
+ */
+
+#define TX_RETIME_SRC_MASK GENMASK(8, 6)
+#define ETH_SEL_TX_RETIME_CLK BIT(8)
+#define ETH_SEL_INTERNAL_NOTEXT_PHYCLK BIT(7)
+#define ETH_SEL_TXCLK_NOT_CLK125 BIT(6)
+
+#define ENMII_MASK GENMASK(5, 5)
+#define ENMII BIT(5)
+
+/**
+ * 3 bits [4:2]
+ * 000-GMII/MII
+ * 001-RGMII
+ * 010-SGMII
+ * 100-RMII
+*/
+#define MII_PHY_SEL_MASK GENMASK(4, 2)
+#define ETH_PHY_SEL_RMII BIT(4)
+#define ETH_PHY_SEL_SGMII BIT(3)
+#define ETH_PHY_SEL_RGMII BIT(2)
+#define ETH_PHY_SEL_GMII 0x0
+#define ETH_PHY_SEL_MII 0x0
+
+#define IS_PHY_IF_MODE_RGMII(iface) (iface == PHY_INTERFACE_MODE_RGMII || \
+ iface == PHY_INTERFACE_MODE_RGMII_ID || \
+ iface == PHY_INTERFACE_MODE_RGMII_RXID || \
+ iface == PHY_INTERFACE_MODE_RGMII_TXID)
+
+#define IS_PHY_IF_MODE_GBIT(iface) (IS_PHY_IF_MODE_RGMII(iface) || \
+ iface == PHY_INTERFACE_MODE_GMII)
+
+struct sti_dwmac {
+ int interface;
+ bool ext_phyclk;
+ bool is_tx_retime_src_clk_125;
+ struct clk *clk;
+ int reg;
+ struct device *dev;
+ struct regmap *regmap;
+};
+
+static u32 phy_intf_sels[] = {
+ [PHY_INTERFACE_MODE_MII] = ETH_PHY_SEL_MII,
+ [PHY_INTERFACE_MODE_GMII] = ETH_PHY_SEL_GMII,
+ [PHY_INTERFACE_MODE_RGMII] = ETH_PHY_SEL_RGMII,
+ [PHY_INTERFACE_MODE_RGMII_ID] = ETH_PHY_SEL_RGMII,
+ [PHY_INTERFACE_MODE_SGMII] = ETH_PHY_SEL_SGMII,
+ [PHY_INTERFACE_MODE_RMII] = ETH_PHY_SEL_RMII,
+};
+
+enum {
+ TX_RETIME_SRC_NA = 0,
+ TX_RETIME_SRC_TXCLK = 1,
+ TX_RETIME_SRC_CLK_125,
+ TX_RETIME_SRC_PHYCLK,
+ TX_RETIME_SRC_CLKGEN,
+};
+
+static const char *const tx_retime_srcs[] = {
+ [TX_RETIME_SRC_NA] = "",
+ [TX_RETIME_SRC_TXCLK] = "txclk",
+ [TX_RETIME_SRC_CLK_125] = "clk_125",
+ [TX_RETIME_SRC_PHYCLK] = "phyclk",
+ [TX_RETIME_SRC_CLKGEN] = "clkgen",
+};
+
+static u32 tx_retime_val[] = {
+ [TX_RETIME_SRC_TXCLK] = ETH_SEL_TXCLK_NOT_CLK125,
+ [TX_RETIME_SRC_CLK_125] = 0x0,
+ [TX_RETIME_SRC_PHYCLK] = ETH_SEL_TX_RETIME_CLK,
+ [TX_RETIME_SRC_CLKGEN] = ETH_SEL_TX_RETIME_CLK |
+ ETH_SEL_INTERNAL_NOTEXT_PHYCLK,
+};
+
+static void setup_retime_src(struct sti_dwmac *dwmac, u32 spd)
+{
+ u32 src = 0, freq = 0;
+
+ if (spd == SPEED_100) {
+ if (dwmac->interface == PHY_INTERFACE_MODE_MII ||
+ dwmac->interface == PHY_INTERFACE_MODE_GMII) {
+ src = TX_RETIME_SRC_TXCLK;
+ } else if (dwmac->interface == PHY_INTERFACE_MODE_RMII) {
+ if (dwmac->ext_phyclk) {
+ src = TX_RETIME_SRC_PHYCLK;
+ } else {
+ src = TX_RETIME_SRC_CLKGEN;
+ freq = 50000000;
+ }
+
+ } else if (IS_PHY_IF_MODE_RGMII(dwmac->interface)) {
+ src = TX_RETIME_SRC_CLKGEN;
+ freq = 25000000;
+ }
+
+ if (src == TX_RETIME_SRC_CLKGEN && dwmac->clk)
+ clk_set_rate(dwmac->clk, freq);
+
+ } else if (spd == SPEED_1000) {
+ if (dwmac->is_tx_retime_src_clk_125)
+ src = TX_RETIME_SRC_CLK_125;
+ else
+ src = TX_RETIME_SRC_TXCLK;
+ }
+
+ regmap_update_bits(dwmac->regmap, dwmac->reg,
+ TX_RETIME_SRC_MASK, tx_retime_val[src]);
+}
+
+static void sti_dwmac_exit(struct platform_device *pdev, void *priv)
+{
+ struct sti_dwmac *dwmac = priv;
+
+ if (dwmac->clk)
+ clk_disable_unprepare(dwmac->clk);
+}
+
+static void sti_fix_mac_speed(void *priv, unsigned int spd)
+{
+ struct sti_dwmac *dwmac = priv;
+
+ setup_retime_src(dwmac, spd);
+
+ return;
+}
+
+static int sti_dwmac_parse_data(struct sti_dwmac *dwmac,
+ struct platform_device *pdev)
+{
+ struct resource *res;
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct regmap *regmap;
+ int err;
+
+ if (!np)
+ return -EINVAL;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "sti-ethconf");
+ if (!res)
+ return -ENODATA;
+
+ regmap = syscon_regmap_lookup_by_phandle(np, "st,syscon");
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ dwmac->dev = dev;
+ dwmac->interface = of_get_phy_mode(np);
+ dwmac->regmap = regmap;
+ dwmac->reg = res->start;
+ dwmac->ext_phyclk = of_property_read_bool(np, "st,ext-phyclk");
+ dwmac->is_tx_retime_src_clk_125 = false;
+
+ if (IS_PHY_IF_MODE_GBIT(dwmac->interface)) {
+ const char *rs;
+
+ err = of_property_read_string(np, "st,tx-retime-src", &rs);
+ if (err < 0) {
+ dev_err(dev, "st,tx-retime-src not specified\n");
+ return err;
+ }
+
+ if (!strcasecmp(rs, "clk_125"))
+ dwmac->is_tx_retime_src_clk_125 = true;
+ }
+
+ dwmac->clk = devm_clk_get(dev, "sti-ethclk");
+
+ if (IS_ERR(dwmac->clk))
+ dwmac->clk = NULL;
+
+ return 0;
+}
+
+static int sti_dwmac_init(struct platform_device *pdev, void *priv)
+{
+ struct sti_dwmac *dwmac = priv;
+ struct regmap *regmap = dwmac->regmap;
+ int iface = dwmac->interface;
+ u32 reg = dwmac->reg;
+ u32 val, spd;
+
+ if (dwmac->clk)
+ clk_prepare_enable(dwmac->clk);
+
+ regmap_update_bits(regmap, reg, MII_PHY_SEL_MASK, phy_intf_sels[iface]);
+
+ val = (iface == PHY_INTERFACE_MODE_REVMII) ? 0 : ENMII;
+ regmap_update_bits(regmap, reg, ENMII_MASK, val);
+
+ if (IS_PHY_IF_MODE_GBIT(iface))
+ spd = SPEED_1000;
+ else
+ spd = SPEED_100;
+
+ setup_retime_src(dwmac, spd);
+
+ return 0;
+}
+
+static void *sti_dwmac_setup(struct platform_device *pdev)
+{
+ struct sti_dwmac *dwmac;
+ int ret;
+
+ dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
+ if (!dwmac)
+ return ERR_PTR(-ENOMEM);
+
+ ret = sti_dwmac_parse_data(dwmac, pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "Unable to parse OF data\n");
+ return ERR_PTR(ret);
+ }
+
+ return dwmac;
+}
+
+const struct stmmac_of_data sti_gmac_data = {
+ .fix_mac_speed = sti_fix_mac_speed,
+ .setup = sti_dwmac_setup,
+ .init = sti_dwmac_init,
+ .exit = sti_dwmac_exit,
+};
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index d9af26e..f9e60d7 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -133,6 +133,9 @@ bool stmmac_eee_init(struct stmmac_priv *priv);
#ifdef CONFIG_DWMAC_SUNXI
extern const struct stmmac_of_data sun7i_gmac_data;
#endif
+#ifdef CONFIG_DWMAC_STI
+extern const struct stmmac_of_data sti_gmac_data;
+#endif
extern struct platform_driver stmmac_pltfr_driver;
static inline int stmmac_register_platform(void)
{
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index 5884a7d..c61bc72b 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -33,6 +33,11 @@ static const struct of_device_id stmmac_dt_ids[] = {
#ifdef CONFIG_DWMAC_SUNXI
{ .compatible = "allwinner,sun7i-a20-gmac", .data = &sun7i_gmac_data},
#endif
+#ifdef CONFIG_DWMAC_STI
+ { .compatible = "st,stih415-dwmac", .data = &sti_gmac_data},
+ { .compatible = "st,stih416-dwmac", .data = &sti_gmac_data},
+ { .compatible = "st,stih127-dwmac", .data = &sti_gmac_data},
+#endif
/* SoC specific glue layers should come before generic bindings */
{ .compatible = "st,spear600-gmac"},
{ .compatible = "snps,dwmac-3.610"},
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v3 2/3] ARM: STi: Add STiH415 ethernet support.
2014-02-11 9:58 ` [PATCH v3 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
2014-02-11 9:59 ` [PATCH v3 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
@ 2014-02-11 10:00 ` srinivas.kandagatla
2014-02-11 10:00 ` [PATCH v3 3/3] ARM: STi: Add STiH416 " srinivas.kandagatla
2014-02-13 21:25 ` [PATCH v3 0/3] net: stmmac: Add STi GMAC ethernet David Miller
3 siblings, 0 replies; 17+ messages in thread
From: srinivas.kandagatla @ 2014-02-11 10:00 UTC (permalink / raw)
To: netdev
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Russell King, Srinivas Kandagatla, Stuart Menefy,
Giuseppe Cavallaro, devicetree, linux-doc, linux-kernel,
linux-arm-kernel, kernel, davem
From: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch adds support to STiH415 SOC, which has two ethernet
snps,dwmac controllers version 3.610. With this patch B2000 and B2020
boards can boot with ethernet in MII and RGMII modes.
Tested on both B2020 and B2000.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
---
arch/arm/boot/dts/stih415-clock.dtsi | 14 ++++
arch/arm/boot/dts/stih415-pinctrl.dtsi | 121 ++++++++++++++++++++++++++++++++
arch/arm/boot/dts/stih415.dtsi | 48 +++++++++++++
arch/arm/boot/dts/stih41x-b2000.dtsi | 22 ++++++
arch/arm/boot/dts/stih41x-b2020.dtsi | 26 +++++++
5 files changed, 231 insertions(+)
diff --git a/arch/arm/boot/dts/stih415-clock.dtsi b/arch/arm/boot/dts/stih415-clock.dtsi
index 174c799..d047dbc 100644
--- a/arch/arm/boot/dts/stih415-clock.dtsi
+++ b/arch/arm/boot/dts/stih415-clock.dtsi
@@ -34,5 +34,19 @@
compatible = "fixed-clock";
clock-frequency = <100000000>;
};
+
+ CLKS_GMAC0_PHY: clockgenA1@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLKS_GMAC0_PHY";
+ };
+
+ CLKS_ETH1_PHY: clockgenA0@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLKS_ETH1_PHY";
+ };
};
};
diff --git a/arch/arm/boot/dts/stih415-pinctrl.dtsi b/arch/arm/boot/dts/stih415-pinctrl.dtsi
index 887c5e5..9ca20aa 100644
--- a/arch/arm/boot/dts/stih415-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih415-pinctrl.dtsi
@@ -119,6 +119,56 @@
};
};
};
+
+ gmac1 {
+ pinctrl_mii1: mii1 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+ col = <&PIO0 7 ALT1 IN BYPASS 1000>;
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
+ mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
+ rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT1 IN NICLK 1000 CLK_A>;
+ };
+ };
+
+ pinctrl_rgmii1: rgmii1-0 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT DE_IO 1000 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ rxd0 = <&PIO1 4 ALT1 IN DE_IO 0 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN DE_IO 0 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN DE_IO 0 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN DE_IO 0 CLK_A>;
+
+ rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
+
+ clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
+ };
+ };
+ };
};
pin-controller-front {
@@ -284,6 +334,77 @@
};
};
};
+
+ gmac0{
+ pinctrl_mii0: mii0 {
+ st,pins {
+ mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
+ txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+
+ txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
+ col = <&PIO15 3 ALT2 IN BYPASS 1000>;
+ mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO13 5 ALT2 OUT NICLK 1000 CLK_A>;
+
+ };
+ };
+
+ pinctrl_gmii0: gmii0 {
+ st,pins {
+ mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
+ mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+ txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+
+ txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd4 = <&PIO14 4 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd5 = <&PIO14 5 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd6 = <&PIO14 6 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd7 = <&PIO14 7 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
+ col = <&PIO15 3 ALT2 IN BYPASS 1000>;
+ rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+
+ rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd4 = <&PIO16 4 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd5 = <&PIO16 5 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd6 = <&PIO16 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd7 = <&PIO16 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+
+ rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+ clk125 = <&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
+
+
+ };
+ };
+ };
};
pin-controller-left {
diff --git a/arch/arm/boot/dts/stih415.dtsi b/arch/arm/boot/dts/stih415.dtsi
index d52207c..cc9b22b 100644
--- a/arch/arm/boot/dts/stih415.dtsi
+++ b/arch/arm/boot/dts/stih415.dtsi
@@ -147,5 +147,53 @@
status = "disabled";
};
+
+ ethernet0: dwmac@fe810000 {
+ device_type = "network";
+ compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610";
+ status = "disabled";
+
+ reg = <0xfe810000 0x8000>, <0x148 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+
+ interrupts = <0 147 0>, <0 148 0>, <0 149 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+ resets = <&softreset STIH415_ETH0_SOFTRESET>;
+ reset-names = "stmmaceth";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+ snps,force_sf_dma_mode;
+
+ st,syscon = <&syscfg_rear>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii0>;
+ clock-names = "stmmaceth";
+ clocks = <&CLKS_GMAC0_PHY>;
+ };
+
+ ethernet1: dwmac@fef08000 {
+ device_type = "network";
+ compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610";
+ status = "disabled";
+ reg = <0xfef08000 0x8000>, <0x74 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+ interrupts = <0 150 0>, <0 151 0>, <0 152 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+ snps,force_sf_dma_mode;
+
+ st,syscon = <&syscfg_sbc>;
+
+ resets = <&softreset STIH415_ETH1_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii1>;
+ clock-names = "stmmaceth";
+ clocks = <&CLKS_ETH1_PHY>;
+ };
};
};
diff --git a/arch/arm/boot/dts/stih41x-b2000.dtsi b/arch/arm/boot/dts/stih41x-b2000.dtsi
index 1e6aa92..bf65c49 100644
--- a/arch/arm/boot/dts/stih41x-b2000.dtsi
+++ b/arch/arm/boot/dts/stih41x-b2000.dtsi
@@ -20,6 +20,8 @@
aliases {
ttyAS0 = &serial2;
+ ethernet0 = ðernet0;
+ ethernet1 = ðernet1;
};
soc {
@@ -46,5 +48,25 @@
status = "okay";
};
+
+ ethernet0: dwmac@fe810000 {
+ status = "okay";
+ phy-mode = "mii";
+ pinctrl-0 = <&pinctrl_mii0>;
+
+ snps,reset-gpio = <&PIO106 2>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 10000>;
+ };
+
+ ethernet1: dwmac@fef08000 {
+ status = "disabled";
+ phy-mode = "mii";
+ st,tx-retime-src = "txclk";
+
+ snps,reset-gpio = <&PIO4 7>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 10000>;
+ };
};
};
diff --git a/arch/arm/boot/dts/stih41x-b2020.dtsi b/arch/arm/boot/dts/stih41x-b2020.dtsi
index 0ef0a69..6c9a2ab 100644
--- a/arch/arm/boot/dts/stih41x-b2020.dtsi
+++ b/arch/arm/boot/dts/stih41x-b2020.dtsi
@@ -19,6 +19,7 @@
aliases {
ttyAS0 = &sbc_serial1;
+ ethernet1 = ðernet1;
};
soc {
sbc_serial1: serial@fe531000 {
@@ -60,5 +61,30 @@
i2c@fe541000 {
status = "okay";
};
+
+ /**
+ * ethernet clk routing:
+ * for
+ * max-speed = <1000>;
+ * set
+ * st,tx-retime-src = "clk_125";
+ *
+ * for
+ * max-speed = <100>;
+ * set
+ * st,tx-retime-src = "clkgen";
+ */
+
+ ethernet1: dwmac@fef08000 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ max-speed = <1000>;
+ st,tx-retime-src = "clk_125";
+ snps,reset-gpio = <&PIO3 0>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 10000>;
+
+ pinctrl-0 = <&pinctrl_rgmii1>;
+ };
};
};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v3 3/3] ARM: STi: Add STiH416 ethernet support.
2014-02-11 9:58 ` [PATCH v3 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
2014-02-11 9:59 ` [PATCH v3 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
2014-02-11 10:00 ` [PATCH v3 2/3] ARM: STi: Add STiH415 ethernet support srinivas.kandagatla
@ 2014-02-11 10:00 ` srinivas.kandagatla
2014-02-13 21:25 ` [PATCH v3 0/3] net: stmmac: Add STi GMAC ethernet David Miller
3 siblings, 0 replies; 17+ messages in thread
From: srinivas.kandagatla @ 2014-02-11 10:00 UTC (permalink / raw)
To: netdev
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Russell King, Srinivas Kandagatla, Stuart Menefy,
Giuseppe Cavallaro, devicetree, linux-doc, linux-kernel,
linux-arm-kernel, kernel, davem
From: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch adds support to STiH416 SOC, which has two ethernet
snps,dwmac controllers version 3.710. With this patch B2000 and B2020
boards can boot with ethernet in MII and RGMII modes.
Tested on both B2020 and B2000.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
---
arch/arm/boot/dts/stih416-clock.dtsi | 14 ++++
arch/arm/boot/dts/stih416-pinctrl.dtsi | 109 ++++++++++++++++++++++++++++++++
arch/arm/boot/dts/stih416.dtsi | 44 +++++++++++++
3 files changed, 167 insertions(+)
diff --git a/arch/arm/boot/dts/stih416-clock.dtsi b/arch/arm/boot/dts/stih416-clock.dtsi
index 7026bf1..a6942c7 100644
--- a/arch/arm/boot/dts/stih416-clock.dtsi
+++ b/arch/arm/boot/dts/stih416-clock.dtsi
@@ -37,5 +37,19 @@
clock-frequency = <100000000>;
clock-output-names = "CLK_S_ICN_REG_0";
};
+
+ CLK_S_GMAC0_PHY: clockgenA1@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLK_S_GMAC0_PHY";
+ };
+
+ CLK_S_ETH1_PHY: clockgenA0@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLK_S_ETH1_PHY";
+ };
};
};
diff --git a/arch/arm/boot/dts/stih416-pinctrl.dtsi b/arch/arm/boot/dts/stih416-pinctrl.dtsi
index 8863c38..c4beef2 100644
--- a/arch/arm/boot/dts/stih416-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih416-pinctrl.dtsi
@@ -132,6 +132,58 @@
};
};
};
+
+ gmac1 {
+ pinctrl_mii1: mii1 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+ col = <&PIO0 7 ALT1 IN BYPASS 1000>;
+
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 1500>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
+ mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
+ rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+
+ rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT1 OUT NICLK 0 CLK_A>;
+ };
+ };
+ pinctrl_rgmii1: rgmii1-0 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT DE_IO 500 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT DE_IO 500 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT DE_IO 500 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT DE_IO 500 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ rxd0 = <&PIO1 4 ALT1 IN DE_IO 500 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN DE_IO 500 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN DE_IO 500 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN DE_IO 500 CLK_A>;
+
+ rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
+
+ clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
+ };
+ };
+ };
};
pin-controller-front {
@@ -322,6 +374,63 @@
};
};
};
+
+ gmac0 {
+ pinctrl_mii0: mii0 {
+ st,pins {
+ mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
+ txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
+ col = <&PIO15 3 ALT2 IN BYPASS 1000>;
+ mdio= <&PIO15 4 ALT2 OUT BYPASS 1500>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO13 5 ALT2 OUT NICLK 0 CLK_B>;
+ };
+ };
+
+ pinctrl_gmii0: gmii0 {
+ st,pins {
+ };
+ };
+ pinctrl_rgmii0: rgmii0 {
+ st,pins {
+ phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
+ txen = <&PIO13 7 ALT2 OUT DE_IO 0 CLK_A>;
+ txd0 = <&PIO14 0 ALT2 OUT DE_IO 500 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT DE_IO 500 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT DE_IO 500 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT DE_IO 500 CLK_B>;
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+
+ mdio = <&PIO15 4 ALT2 OUT BYPASS 0>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxdv = <&PIO15 6 ALT2 IN DE_IO 500 CLK_A>;
+ rxd0 =<&PIO16 0 ALT2 IN DE_IO 500 CLK_A>;
+ rxd1 =<&PIO16 1 ALT2 IN DE_IO 500 CLK_A>;
+ rxd2 =<&PIO16 2 ALT2 IN DE_IO 500 CLK_A>;
+ rxd3 =<&PIO16 3 ALT2 IN DE_IO 500 CLK_A>;
+ rxclk =<&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+
+ clk125=<&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
+ };
+ };
+ };
};
pin-controller-fvdp-fe {
diff --git a/arch/arm/boot/dts/stih416.dtsi b/arch/arm/boot/dts/stih416.dtsi
index 788ba5b..a96055b 100644
--- a/arch/arm/boot/dts/stih416.dtsi
+++ b/arch/arm/boot/dts/stih416.dtsi
@@ -156,5 +156,49 @@
status = "disabled";
};
+
+ ethernet0: dwmac@fe810000 {
+ device_type = "network";
+ compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+ status = "disabled";
+ reg = <0xfe810000 0x8000>, <0x8bc 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+
+ interrupts = <0 133 0>, <0 134 0>, <0 135 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+
+ st,syscon = <&syscfg_rear>;
+ resets = <&softreset STIH416_ETH0_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii0>;
+ clock-names = "stmmaceth";
+ clocks = <&CLK_S_GMAC0_PHY>;
+ };
+
+ ethernet1: dwmac@fef08000 {
+ device_type = "network";
+ compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+ status = "disabled";
+ reg = <0xfef08000 0x8000>, <0x7f0 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+ interrupts = <0 136 0>, <0 137 0>, <0 138 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+
+ st,syscon = <&syscfg_sbc>;
+
+ resets = <&softreset STIH416_ETH1_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii1>;
+ clock-names = "stmmaceth";
+ clocks = <&CLK_S_ETH1_PHY>;
+ };
};
};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 17+ messages in thread
* Re: [PATCH v3 0/3] net: stmmac: Add STi GMAC ethernet
2014-02-11 9:58 ` [PATCH v3 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
` (2 preceding siblings ...)
2014-02-11 10:00 ` [PATCH v3 3/3] ARM: STi: Add STiH416 " srinivas.kandagatla
@ 2014-02-13 21:25 ` David Miller
3 siblings, 0 replies; 17+ messages in thread
From: David Miller @ 2014-02-13 21:25 UTC (permalink / raw)
To: srinivas.kandagatla
Cc: netdev, robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak,
rob, linux, stuart.menefy, peppe.cavallaro, devicetree,
linux-doc, linux-kernel, linux-arm-kernel, kernel
From: <srinivas.kandagatla@st.com>
Date: Tue, 11 Feb 2014 09:58:36 +0000
> Dave, Can I request you to take the first patch via net tree for v3.15, I can
> request Arnd or Olof to take the DT patches via the arm-soc tree for v3.15.
Since it's a new driver, I decided to add it to the plain 'net' tree.
Thanks.
^ permalink raw reply [flat|nested] 17+ messages in thread
end of thread, other threads:[~2014-02-13 21:26 UTC | newest]
Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-02-03 11:59 [PATCH v1 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
2014-02-03 12:01 ` [PATCH v1 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
2014-02-07 3:53 ` David Miller
2014-02-07 7:54 ` srinivas kandagatla
2014-02-03 12:01 ` [PATCH v1 2/3] ARM: STi: Add STiH415 ethernet support srinivas.kandagatla
2014-02-03 12:02 ` [PATCH v1 3/3] ARM: STi: Add STiH416 " srinivas.kandagatla
2014-02-07 10:54 ` [PATCH v2 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
2014-02-07 10:55 ` [PATCH v2 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
2014-02-10 22:40 ` David Miller
2014-02-11 9:01 ` srinivas kandagatla
2014-02-07 10:55 ` [PATCH v2 2/3] ARM: STi: Add STiH415 ethernet support srinivas.kandagatla
2014-02-07 10:55 ` [PATCH v2 3/3] ARM: STi: Add STiH416 " srinivas.kandagatla
2014-02-11 9:58 ` [PATCH v3 0/3] net: stmmac: Add STi GMAC ethernet srinivas.kandagatla
2014-02-11 9:59 ` [PATCH v3 1/3] net: stmmac:sti: Add STi SOC glue driver srinivas.kandagatla
2014-02-11 10:00 ` [PATCH v3 2/3] ARM: STi: Add STiH415 ethernet support srinivas.kandagatla
2014-02-11 10:00 ` [PATCH v3 3/3] ARM: STi: Add STiH416 " srinivas.kandagatla
2014-02-13 21:25 ` [PATCH v3 0/3] net: stmmac: Add STi GMAC ethernet David Miller
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).