From: Gyungoh Yoo <gyungoh@gmail.com>
To: robh+dt@kernel.org, pawel.moll@arm.com, mark.rutland@arm.com,
ijc+devicetree@hellion.org.uk, galak@codeaurora.org
Cc: lgirdwood@gmail.com, broonie@kernel.org,
jack.yoo@skyworksinc.com, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH 2/3] Adding Skyworks SKY81452 regulator driver
Date: Fri, 8 Aug 2014 18:10:22 +0900 [thread overview]
Message-ID: <1407489022-31130-1-git-send-email-jack.yoo@skyworksinc.com> (raw)
Signed-off-by: Gyungoh Yoo <jack.yoo@skyworksinc.com>
---
.../bindings/regulator/sky81452-regulator.txt | 16 +++
drivers/regulator/Kconfig | 11 ++
drivers/regulator/Makefile | 1 +
drivers/regulator/sky81452-regulator.c | 130 +++++++++++++++++++++
4 files changed, 158 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/sky81452-regulator.txt
create mode 100644 drivers/regulator/sky81452-regulator.c
diff --git a/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt b/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt
new file mode 100644
index 0000000..f98b5ed
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt
@@ -0,0 +1,16 @@
+SKY81452 voltage regulator
+
+Required properties:
+- any required generic properties defined in regulator.txt
+
+Optional properties:
+- any available generic properties defined in regulator.txt
+
+Example:
+
+ regualtor {
+ /* generic regulator properties */
+ regulator-name = "touch_en";
+ regulator-min-microvolt = <4500000>;
+ regulator-max-microvolt = <8000000>;
+ };
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 2dc8289..f6bf208 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -483,6 +483,17 @@ config REGULATOR_S5M8767
via I2C bus. S5M8767A have 9 Bucks and 28 LDOs output and
supports DVS mode with 8bits of output voltage control.
+config REGULATOR_SKY81452
+ tristate "Skyworks Solutions SKY81452 voltage regulator"
+ depends on SKY81452
+ help
+ This driver supports Skyworks SKY81452 voltage output regulator
+ via I2C bus. SKY81452 has one voltage linear regulator can be
+ programmed from 4.5V to 20V.
+
+ This driver can also be built as a module. If so, the module
+ will be called sky81452-regulator.
+
config REGULATOR_ST_PWM
tristate "STMicroelectronics PWM voltage regulator"
depends on ARCH_STI
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index aa4a6aa..d8206ec 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -65,6 +65,7 @@ obj-$(CONFIG_REGULATOR_RC5T583) += rc5t583-regulator.o
obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
+obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o
obj-$(CONFIG_REGULATOR_ST_PWM) += st-pwm.o
obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o
diff --git a/drivers/regulator/sky81452-regulator.c b/drivers/regulator/sky81452-regulator.c
new file mode 100644
index 0000000..97aff0c
--- /dev/null
+++ b/drivers/regulator/sky81452-regulator.c
@@ -0,0 +1,130 @@
+/*
+ * sky81452-regulator.c SKY81452 regulator driver
+ *
+ * Copyright 2014 Skyworks Solutions Inc.
+ * Author : Gyungoh Yoo <jack.yoo@skyworksinc.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2, or (at your option) any
+ * later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/of.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+/* registers */
+#define SKY81452_REG1 0x01
+#define SKY81452_REG3 0x03
+
+/* bit mask */
+#define SKY81452_LEN 0x40
+#define SKY81452_LOUT 0x1F
+
+static struct regulator_ops sky81452_reg_ops = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+};
+
+static const struct regulator_linear_range sky81452_reg_ranges[] = {
+ REGULATOR_LINEAR_RANGE(4500000, 0, 14, 250000),
+ REGULATOR_LINEAR_RANGE(9000000, 15, 31, 1000000),
+};
+
+static const struct regulator_desc sky81452_reg = {
+ .name = "LOUT",
+ .ops = &sky81452_reg_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .n_voltages = SKY81452_LOUT + 1,
+ .linear_ranges = sky81452_reg_ranges,
+ .n_linear_ranges = ARRAY_SIZE(sky81452_reg_ranges),
+ .vsel_reg = SKY81452_REG3,
+ .vsel_mask = SKY81452_LOUT,
+ .enable_reg = SKY81452_REG1,
+ .enable_mask = SKY81452_LEN,
+};
+
+#ifdef CONFIG_OF
+static struct regulator_init_data *sky81452_reg_parse_dt(struct device *dev)
+{
+ struct regulator_init_data *init_data;
+ struct device_node *np;
+
+ np = of_get_child_by_name(dev->parent->of_node, "regulator");
+ if (unlikely(!np)) {
+ dev_err(dev, "regulator node not found");
+ return NULL;
+ }
+
+ init_data = of_get_regulator_init_data(dev, np);
+
+ of_node_put(np);
+ return init_data;
+}
+#else
+static struct regulator_init_data *sky81452_reg_parse_dt(struct device *dev)
+{
+ return ERR_PTR(-EINVAL);
+}
+#endif
+
+static int sky81452_reg_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ const struct regulator_init_data *init_data = dev_get_platdata(dev);
+ struct regulator_config config = { };
+ struct regulator_dev *rdev;
+
+ if (!init_data) {
+ init_data = sky81452_reg_parse_dt(dev);
+ if (IS_ERR(init_data))
+ return PTR_ERR(init_data);
+ }
+
+ config.dev = dev;
+ config.init_data = init_data;
+ config.of_node = dev->of_node;
+ config.regmap = dev_get_drvdata(dev->parent);
+
+ rdev = devm_regulator_register(dev, &sky81452_reg, &config);
+ if (IS_ERR(rdev))
+ return PTR_ERR(rdev);
+
+ platform_set_drvdata(pdev, rdev);
+
+ return 0;
+}
+
+static struct platform_driver sky81452_reg_driver = {
+ .driver = {
+ .name = "sky81452-regulator",
+ },
+ .probe = sky81452_reg_probe,
+};
+
+module_platform_driver(sky81452_reg_driver);
+
+MODULE_DESCRIPTION("Skyworks SKY81452 Regulator driver");
+MODULE_AUTHOR("Gyungoh Yoo <jack.yoo@skyworksinc.com>");
+MODULE_LICENSE("GPL");
+MODULE_VERSION("1.0");
--
1.9.1
next reply other threads:[~2014-08-08 9:10 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-08-08 9:10 Gyungoh Yoo [this message]
2014-08-13 19:04 ` [PATCH 2/3] Adding Skyworks SKY81452 regulator driver Mark Brown
2014-09-01 2:40 ` [PATCH v2.2 0/2] regulator: sky81452: Adding compatible attribute in DT document Gyungoh Yoo
2014-09-01 2:40 ` [PATCH v2.2 1/2] regulator: sky81452: Adding compatible attribute in DT Gyungoh Yoo
2014-09-01 2:40 ` [PATCH v2.2 2/2] dt-bindings: Adding compatible attribute for SKY81452 regulator Gyungoh Yoo
2014-09-01 10:31 ` Mark Brown
2014-09-05 1:55 ` Gyungoh Yoo
2014-09-06 14:38 ` Mark Brown
2014-09-11 5:22 ` Gyungoh Yoo
2014-09-15 22:35 ` Mark Brown
2014-09-19 6:17 ` Gyungoh Yoo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1407489022-31130-1-git-send-email-jack.yoo@skyworksinc.com \
--to=gyungoh@gmail.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=jack.yoo@skyworksinc.com \
--cc=lgirdwood@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).