[PATCH v3 0/4] Add picoPHY usb phy driver found on stih407 family SoC's

[PATCH v3 0/4] Add picoPHY usb phy driver found on stih407 family SoC's

[Peter Griffin]

This series adds support for the picoPHY usb phy which is used by the usb2
and usb3 host controllers when controlling usb2/1.1 devices. It is found on
stih407 family SoC's from the consumer electronics devision of STMicroelectronics.

Changes since v2:
 - Remove .data and hardcode phy ops in devm_phy_create call (arndb)
 - Add COMPILE_TEST in kconfig (arndb)
 - Add depends on RESET_CONTROLLER in kconfig so COMPILE_TEST works
 - select GENERIC_PHY instead of depends on (Bartlomiej)

Changes since v1:
 - Remove reference to stih410 in dt documentation (kishon)
 - Fix alignment issue in dt example (kishon)
 - usbpicophy@f8 since you have a reg property (kishon)
 - Enable driver in multi_v7_defconfig

Peter Griffin (4):
  phy: phy-stih407-usb: Add usb picoPHY driver found on stih407 SoC
    family
  phy: phy-stih407-usb: Add dt documentation for USB picophy found on
    stih407 SoC family
  MAINTAINERS: Add phy-stih407-usb.c file to ARCH/STI architecture
  ARM: multi_v7_defconfig: Enable stih407 usb picophy

 .../devicetree/bindings/phy/phy-stih407-usb.txt    |  30 ++++
 MAINTAINERS                                        |   1 +
 arch/arm/configs/multi_v7_defconfig                |   1 +
 drivers/phy/Kconfig                                |   9 ++
 drivers/phy/Makefile                               |   2 +
 drivers/phy/phy-stih407-usb.c                      | 177 +++++++++++++++++++++
 6 files changed, 220 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
 create mode 100644 drivers/phy/phy-stih407-usb.c

-- 
1.9.1

[PATCH v3 1/4] phy: phy-stih407-usb: Add usb picoPHY driver found on stih407 SoC family

[Peter Griffin]

This is the generic phy driver for the picoPHY ports used by the
USB2 and USB3 Host controllers when controlling usb2/1.1 devices. It
is found on STiH407 SoC family from STMicroelectronics.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 drivers/phy/Kconfig           |   9 +++
 drivers/phy/Makefile          |   2 +
 drivers/phy/phy-stih407-usb.c | 177 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 188 insertions(+)
 create mode 100644 drivers/phy/phy-stih407-usb.c

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 0dd7427..d361d98 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -230,4 +230,13 @@ config PHY_XGENE
 	help
 	  This option enables support for APM X-Gene SoC multi-purpose PHY.
 
+config PHY_STIH407_USB
+	tristate "STMicroelectronics USB2 picoPHY driver for STiH407 family"
+	depends on RESET_CONTROLLER
+	depends on ARCH_STI || COMPILE_TEST
+	select GENERIC_PHY
+	help
+	  Enable this support to enable the picoPHY device used by USB2
+	  and USB3 controllers on STMicroelectronics STiH407 SoC families.
+
 endmenu
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 95c69ed..c82ac59 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -28,3 +28,5 @@ obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
 obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
 obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o
 obj-$(CONFIG_PHY_XGENE)			+= phy-xgene.o
+obj-$(CONFIG_PHY_STIH407_USB)		+= phy-stih407-usb.o
+
diff --git a/drivers/phy/phy-stih407-usb.c b/drivers/phy/phy-stih407-usb.c
new file mode 100644
index 0000000..42428d4
--- /dev/null
+++ b/drivers/phy/phy-stih407-usb.c
@@ -0,0 +1,177 @@
+/*
+ * Copyright (C) 2014 STMicroelectronics
+ *
+ * STMicroelectronics Generic PHY driver for STiH407 USB2.
+ *
+ * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/clk.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/mfd/syscon.h>
+#include <linux/phy/phy.h>
+
+/* Default PHY_SEL and REFCLKSEL configuration */
+#define STIH407_USB_PICOPHY_CTRL_PORT_CONF	0x6
+#define STIH407_USB_PICOPHY_CTRL_PORT_MASK	0x1f
+
+/* ports parameters overriding */
+#define STIH407_USB_PICOPHY_PARAM_DEF		0x39a4dc
+#define STIH407_USB_PICOPHY_PARAM_MASK		0xffffffff
+
+struct stih407_usb2_picophy {
+	struct phy *phy;
+	struct regmap *regmap;
+	struct device *dev;
+	struct reset_control *rstc;
+	struct reset_control *rstport;
+	int ctrl;
+	int param;
+};
+
+static int stih407_usb2_pico_ctrl(struct stih407_usb2_picophy *phy_dev)
+{
+	reset_control_deassert(phy_dev->rstc);
+
+	return regmap_update_bits(phy_dev->regmap, phy_dev->ctrl,
+				  STIH407_USB_PICOPHY_CTRL_PORT_MASK,
+				  STIH407_USB_PICOPHY_CTRL_PORT_CONF);
+}
+
+static int stih407_usb2_init_port(struct phy *phy)
+{
+	int ret;
+	struct stih407_usb2_picophy *phy_dev = phy_get_drvdata(phy);
+
+	stih407_usb2_pico_ctrl(phy_dev);
+
+	ret = regmap_update_bits(phy_dev->regmap,
+				 phy_dev->param,
+				 STIH407_USB_PICOPHY_PARAM_MASK,
+				 STIH407_USB_PICOPHY_PARAM_DEF);
+	if (ret)
+		return ret;
+
+	return reset_control_deassert(phy_dev->rstport);
+}
+
+static int stih407_usb2_exit_port(struct phy *phy)
+{
+	struct stih407_usb2_picophy *phy_dev = phy_get_drvdata(phy);
+
+	/*
+	 * Only port reset is asserted, phy global reset is kept untouched
+	 * as other ports may still be active. When all ports are in reset
+	 * state, assumption is made that power will be cut off on the phy, in
+	 * case of suspend for instance. Theoretically, asserting individual
+	 * reset (like here) or global reset should be equivalent.
+	 */
+	return reset_control_assert(phy_dev->rstport);
+}
+
+static const struct phy_ops stih407_usb2_picophy_data = {
+	.init = stih407_usb2_init_port,
+	.exit = stih407_usb2_exit_port,
+	.owner = THIS_MODULE,
+};
+
+static int stih407_usb2_picophy_probe(struct platform_device *pdev)
+{
+	struct stih407_usb2_picophy *phy_dev;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct phy_provider *phy_provider;
+	struct phy *phy;
+	struct resource *res;
+
+	phy_dev = devm_kzalloc(dev, sizeof(*phy_dev), GFP_KERNEL);
+	if (!phy_dev)
+		return -ENOMEM;
+
+	phy_dev->dev = dev;
+	dev_set_drvdata(dev, phy_dev);
+
+	phy_dev->rstc = devm_reset_control_get(dev, "global");
+	if (IS_ERR(phy_dev->rstc)) {
+		dev_err(dev, "failed to ctrl picoPHY reset\n");
+		return PTR_ERR(phy_dev->rstc);
+	}
+
+	phy_dev->rstport = devm_reset_control_get(dev, "port");
+	if (IS_ERR(phy_dev->rstport)) {
+		dev_err(dev, "failed to ctrl picoPHY reset\n");
+		return PTR_ERR(phy_dev->rstport);
+	}
+
+	/* Reset port by default: only deassert it in phy init */
+	reset_control_assert(phy_dev->rstport);
+
+	phy_dev->regmap = syscon_regmap_lookup_by_phandle(np, "st,syscfg");
+	if (IS_ERR(phy_dev->regmap)) {
+		dev_err(dev, "No syscfg phandle specified\n");
+		return PTR_ERR(phy_dev->regmap);
+	}
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
+	if (!res) {
+		dev_err(dev, "No ctrl reg found\n");
+		return -ENXIO;
+	}
+	phy_dev->ctrl = res->start;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "param");
+	if (!res) {
+		dev_err(dev, "No param reg found\n");
+		return -ENXIO;
+	}
+	phy_dev->param = res->start;
+
+	phy = devm_phy_create(dev, NULL, &stih407_usb2_picophy_data, NULL);
+	if (IS_ERR(phy)) {
+		dev_err(dev, "failed to create Display Port PHY\n");
+		return PTR_ERR(phy);
+	}
+
+	phy_dev->phy = phy;
+	phy_set_drvdata(phy, phy_dev);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(phy_provider))
+		return PTR_ERR(phy_provider);
+
+	dev_info(dev, "STiH407 USB Generic picoPHY driver probed!");
+
+	return 0;
+}
+
+static const struct of_device_id stih407_usb2_picophy_of_match[] = {
+	{ .compatible = "st,stih407-usb2-phy" },
+	{ /*sentinel */ },
+};
+
+MODULE_DEVICE_TABLE(of, stih407_usb2_picophy_of_match);
+
+static struct platform_driver stih407_usb2_picophy_driver = {
+	.probe = stih407_usb2_picophy_probe,
+	.driver = {
+		   .name = "stih407-usb-genphy",
+		   .of_match_table = stih407_usb2_picophy_of_match,
+		   }
+};
+
+module_platform_driver(stih407_usb2_picophy_driver);
+
+MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
+MODULE_DESCRIPTION("STMicroelectronics Generic picoPHY driver for STiH407");
+MODULE_LICENSE("GPL v2");
-- 
1.9.1

[PATCH v3 2/4] phy: phy-stih407-usb: Add dt documentation for USB picophy found on stih407 SoC family

[Peter Griffin]

This patch adds the dt documentation for the usb picophy found on stih407 SoC family
available from STMicroelectronics.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 .../devicetree/bindings/phy/phy-stih407-usb.txt    | 30 ++++++++++++++++++++++
 1 file changed, 30 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-stih407-usb.txt

diff --git a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
new file mode 100644
index 0000000..1ef8228
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
@@ -0,0 +1,30 @@
+ST STiH407 USB PHY controller
+
+This file documents the dt bindings for the usb picoPHY driver which is the PHY for both USB2 and USB3
+host controllers (when controlling usb2/1.1 devices) available on STiH407 SoC family from STMicroelectronics.
+
+Required properties:
+- compatible		: should be "st,stih407-usb2-phy"
+- reg			: contain the offset and length of the system configuration registers
+			  used as glue logic to control & parameter phy
+- reg-names		: the names of the system configuration registers in "reg", should be "param" and "reg"
+- st,syscfg		: sysconfig register to manage phy parameter at driver level
+- resets		: list of phandle and reset specifier pairs. There should be two entries, one
+			  for the whole phy and one for the port
+- reset-names		: list of reset signal names. Should be "global" and "port"
+See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
+See: Documentation/devicetree/bindings/reset/reset.txt
+
+Example:
+
+usb2_picophy0: usbpicophy@f8 {
+	compatible	= "st,stih407-usb2-phy";
+	reg		= <0xf8 0x04>,	/* syscfg 5062 */
+			  <0xf4 0x04>;	/* syscfg 5061 */
+	reg-names	= "param", "ctrl";
+	#phy-cells	= <0>;
+	st,syscfg	= <&syscfg_core>;
+	resets		= <&softreset STIH407_PICOPHY_SOFTRESET>,
+			  <&picophyreset STIH407_PICOPHY0_RESET>;
+	reset-names	= "global", "port";
+};
-- 
1.9.1

[PATCH v3 3/4] MAINTAINERS: Add phy-stih407-usb.c file to ARCH/STI architecture

[Peter Griffin]

This patch adds the new phy-stih407-usb.c usb phy driver found on
STMicroelectronics stih407 consumer electronics SoC's into the STI
arch section of the maintainers file.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index cf24bb5..3ccb4cc 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1398,6 +1398,7 @@ F:	drivers/media/rc/st_rc.c
 F:	drivers/i2c/busses/i2c-st.c
 F:	drivers/tty/serial/st-asc.c
 F:	drivers/mmc/host/sdhci-st.c
+F:	drivers/phy/phy-stih407-usb.c
 
 ARM/TECHNOLOGIC SYSTEMS TS7250 MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
-- 
1.9.1

[PATCH v3 4/4] ARM: multi_v7_defconfig: Enable stih407 usb picophy

[Peter Griffin]

This patch enables the picoPHY usb phy which is used by
the usb2 and usb3 host controllers when controlling usb2/1.1
devices. It is found in stih407 family SoC's from STMicroelectronics.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 arch/arm/configs/multi_v7_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index 5fb95fb..65f4611 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -387,6 +387,7 @@ CONFIG_PWM_VT8500=y
 CONFIG_OMAP_USB2=y
 CONFIG_TI_PIPE3=y
 CONFIG_PHY_MIPHY365X=y
+CONFIG_PHY_STIH407_USB=y
 CONFIG_PHY_SUN4I_USB=y
 CONFIG_EXT4_FS=y
 CONFIG_VFAT_FS=y
-- 
1.9.1