[PATCH v2 00/11] memory: add Atmel EBI (External Bus Interface) driver

[PATCH v2 00/11] memory: add Atmel EBI (External Bus Interface) driver

[Boris Brezillon]

The EBI (External Bus Interface) is used to access external peripherals
(NOR, SRAM, NAND, and other specific devices like ethernet controllers).
Each device is assigned a CS line and an address range and can have its
own configuration (timings, access mode, bus width, ...).
This driver provides a generic DT binding to configure a device according
to its requirements.
For specific device controllers (like the NAND one) the SMC timings
should be configured by the controller driver through the matrix and
smc syscon regmaps.

The first 4 patches introduce 2 syscon devices needed to configure the
EBI bus, patch 5 and 6 adds support for the EBI bus, and the remaining
patches declares the EBI related nodes in sama5d3 dts[i] files.

The converters approach I suggested to Jean-Jacques has been dropped
and only SMC specific timing properties are supported.

Arnd, you've commented the first version of this driver (IIRC, you
focused on the DT binding part), could you give your feedback on this
version (I based the new DT binding on TI's aemif driver).

Changes since v1:
- almost everything :-)

Boris Brezillon (11):
  mfd: syscon: Add atmel-matrix registers definition
  mfd: syscon: Add Atmel Matrix bus DT binding documentation
  mfd: syscon: Add atmel-smc registers definition
  mfd: syscon: Add Atmel SMC binding doc
  memory: add Atmel EBI (External Bus Interface) driver
  memory: atmel-ebi: add DT bindings documentation
  ARM: at91: select ATMEL_EBI when compiling a kernel for at91sam9 or
    sama5d3
  ARM: at91/dt: add HSMC (Static Memory Controller) node in sama5d3 dtsi
  ARM: at91/dt: add matrix node in sama5d3 dtsi
  ARM: at91/dt: add EBI (External Bus Interface) node in sama5d3 dtsi
  ARM: at91/dt: add NOR definition in sama5d3xcm dtsi

 .../bindings/memory-controllers/atmel-ebi.txt      | 153 +++++
 .../devicetree/bindings/mfd/atmel-matrix.txt       |  24 +
 .../devicetree/bindings/mfd/atmel-smc.txt          |  19 +
 arch/arm/boot/dts/sama5d3.dtsi                     |  93 ++++
 arch/arm/boot/dts/sama5d3xcm.dtsi                  |  34 ++
 arch/arm/mach-at91/Kconfig                         |   2 +
 drivers/memory/Kconfig                             |  11 +
 drivers/memory/Makefile                            |   1 +
 drivers/memory/atmel-ebi.c                         | 615 +++++++++++++++++++++
 include/linux/mfd/syscon/atmel-matrix.h            | 114 ++++
 include/linux/mfd/syscon/atmel-smc.h               |  60 ++
 11 files changed, 1126 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt
 create mode 100644 Documentation/devicetree/bindings/mfd/atmel-matrix.txt
 create mode 100644 Documentation/devicetree/bindings/mfd/atmel-smc.txt
 create mode 100644 drivers/memory/atmel-ebi.c
 create mode 100644 include/linux/mfd/syscon/atmel-matrix.h
 create mode 100644 include/linux/mfd/syscon/atmel-smc.h

-- 
1.9.1

[PATCH v2 01/11] mfd: syscon: Add atmel-matrix registers definition

[Boris Brezillon]

AT91 SoCs have a memory range reserved for internal bus configuration.
Expose those registers so that drivers can make use of the matrix syscon
declared in at91 DTs.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
---
 include/linux/mfd/syscon/atmel-matrix.h | 114 ++++++++++++++++++++++++++++++++
 1 file changed, 114 insertions(+)
 create mode 100644 include/linux/mfd/syscon/atmel-matrix.h

diff --git a/include/linux/mfd/syscon/atmel-matrix.h b/include/linux/mfd/syscon/atmel-matrix.h
new file mode 100644
index 0000000..c3faa18
--- /dev/null
+++ b/include/linux/mfd/syscon/atmel-matrix.h
@@ -0,0 +1,114 @@
+/*
+ *  Copyright (C) 2007 Atmel Corporation.
+ *
+ * Memory Controllers (MATRIX, EBI) - System peripherals registers.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef _LINUX_MFD_SYSCON_ATMEL_MATRIX_H
+#define _LINUX_MFD_SYSCON_ATMEL_MATRIX_H
+
+#define AT91SAM9260_MATRIX_MCFG_OFF	0x00
+#define AT91SAM9260_MATRIX_SCFG_OFF	0x40
+#define AT91SAM9260_MATRIX_PRS_OFF	0x80
+#define AT91SAM9260_MATRIX_MRCR_OFF	0x100
+#define AT91SAM9260_MATRIX_EBICSA_OFF	0x11c
+
+#define AT91SAM9261_MATRIX_MRCR_OFF	0x0
+#define AT91SAM9261_MATRIX_SCFG_OFF	0x4
+#define AT91SAM9261_MATRIX_TCR_OFF	0x24
+#define AT91SAM9261_MATRIX_EBICSA_OFF	0x30
+#define AT91SAM9261_MATRIX_USBPUCR_OFF	0x34
+
+#define AT91SAM9263_MATRIX_MCFG_OFF	0x00
+#define AT91SAM9263_MATRIX_SCFG_OFF	0x40
+#define AT91SAM9263_MATRIX_PRS_OFF	0x80
+#define AT91SAM9263_MATRIX_MRCR_OFF	0x100
+#define AT91SAM9263_MATRIX_TCR_OFF	0x114
+#define AT91SAM9263_MATRIX_EBI0CSA_OFF	0x120
+#define AT91SAM9263_MATRIX_EBI1CSA_OFF	0x124
+
+#define AT91SAM9G45_MATRIX_MCFG_OFF	0x00
+#define AT91SAM9G45_MATRIX_SCFG_OFF	0x40
+#define AT91SAM9G45_MATRIX_PRS_OFF	0x80
+#define AT91SAM9G45_MATRIX_MRCR_OFF	0x100
+#define AT91SAM9G45_MATRIX_TCR_OFF	0x110
+#define AT91SAM9G45_MATRIX_DDRMPR_OFF	0x118
+#define AT91SAM9G45_MATRIX_EBICSA_OFF	0x128
+
+#define AT91SAM9N12_MATRIX_MCFG_OFF	0x00
+#define AT91SAM9N12_MATRIX_SCFG_OFF	0x40
+#define AT91SAM9N12_MATRIX_PRS_OFF	0x80
+#define AT91SAM9N12_MATRIX_MRCR_OFF	0x100
+#define AT91SAM9N12_MATRIX_EBICSA_OFF	0x118
+
+#define AT91SAM9X5_MATRIX_MCFG_OFF	0x00
+#define AT91SAM9X5_MATRIX_SCFG_OFF	0x40
+#define AT91SAM9X5_MATRIX_PRS_OFF	0x80
+#define AT91SAM9X5_MATRIX_MRCR_OFF	0x100
+#define AT91SAM9X5_MATRIX_EBICSA_OFF	0x120
+
+#define SAMA5D3_MATRIX_MCFG_OFF		0x00
+#define SAMA5D3_MATRIX_SCFG_OFF		0x40
+#define SAMA5D3_MATRIX_PRS_OFF		0x80
+#define SAMA5D3_MATRIX_MRCR_OFF		0x100
+
+#define AT91_MATRIX_MCFG(o, x)		((o) + ((x) * 0x4))
+#define AT91_MATRIX_ULBT		(7 << 0)
+#define AT91_MATRIX_ULBT_INFINITE	(0 << 0)
+#define AT91_MATRIX_ULBT_SINGLE		(1 << 0)
+#define AT91_MATRIX_ULBT_FOUR		(2 << 0)
+#define AT91_MATRIX_ULBT_EIGHT		(3 << 0)
+#define AT91_MATRIX_ULBT_SIXTEEN	(4 << 0)
+
+#define AT91_MATRIX_SCFG(o, x)		((o) + ((x) * 0x4))
+#define AT91_MATRIX_SLOT_CYCLE		(0xff <<  0)
+#define AT91_MATRIX_DEFMSTR_TYPE	(3 << 16)
+#define AT91_MATRIX_DEFMSTR_TYPE_NONE	(0 << 16)
+#define AT91_MATRIX_DEFMSTR_TYPE_LAST	(1 << 16)
+#define AT91_MATRIX_DEFMSTR_TYPE_FIXED	(2 << 16)
+#define AT91_MATRIX_FIXED_DEFMSTR	(7 << 18)
+#define AT91_MATRIX_ARBT		(3 << 24)
+#define AT91_MATRIX_ARBT_ROUND_ROBIN	(0 << 24)
+#define AT91_MATRIX_ARBT_FIXED_PRIORITY	(1 << 24)
+
+#define AT91_MATRIX_TCR(o)		(o)
+#define AT91_MATRIX_ITCM_SIZE		(0xf << 0)
+#define AT91_MATRIX_ITCM_0		(0 << 0)
+#define AT91_MATRIX_ITCM_16		(5 << 0)
+#define AT91_MATRIX_ITCM_32		(6 << 0)
+#define AT91_MATRIX_ITCM_64		(7 << 0)
+#define	AT91_MATRIX_DTCM_SIZE		(0xf << 4)
+#define	AT91_MATRIX_DTCM_0		(0 << 4)
+#define	AT91_MATRIX_DTCM_16		(5 << 4)
+#define AT91_MATRIX_DTCM_32		(6 << 4)
+#define AT91_MATRIX_DTCM_64		(7 << 4)
+
+#define AT91_MATRIX_PRAS(o, x)		((o) + ((x) * 0x8))
+#define AT91_MATRIX_PRBS(o, x)		((o) + ((x) * 0x8) + 0x4)
+#define AT91_MATRIX_MPR_MSK(x)		(3 << ((x) * 0x4))
+
+#define AT91_MATRIX_MRC(o)		(o)
+#define AT91_MATRIX_RCB(x)		BIT(x)
+
+#define AT91_MATRIX_EBICSA(o)		(o)
+#define AT91_MATRIX_CSA(cs, val)	(val << (cs))
+#define AT91_MATRIX_DBPUC		BIT(8)
+#define AT91_MATRIX_DBPDC		BIT(9)
+#define AT91_MATRIX_VDDIOMSEL		BIT(16)
+#define AT91_MATRIX_VDDIOMSEL_1_8V	(0 << 16)
+#define AT91_MATRIX_VDDIOMSEL_3_3V	(1 << 16)
+#define AT91_MATRIX_EBI_IOSR		BIT(17)
+#define AT91_MATRIX_DDR_IOSR		BIT(18)
+#define AT91_MATRIX_NFD0_SELECT		BIT(24)
+#define AT91_MATRIX_DDR_MP_EN		BIT(25)
+#define AT91_MATRIX_EBI_NUM_CS		8
+
+#define AT91_MATRIX_WPMR(o)		(o)
+#define AT91_MATRIX_WPSR(o)		(o)
+
+#endif /* _LINUX_MFD_SYSCON_ATMEL_MATRIX_H */
-- 
1.9.1

[PATCH v2 02/11] mfd: syscon: Add Atmel Matrix bus DT binding documentation

[Boris Brezillon]

The Matrix registers are provided to configure internal bus behavior on
at91 SoCs.
Some registers might be access by several drivers (e.g. to configure
external memory bus timings), hence we declare this register set as a
syscon device.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
---
 .../devicetree/bindings/mfd/atmel-matrix.txt       | 24 ++++++++++++++++++++++
 1 file changed, 24 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/atmel-matrix.txt

diff --git a/Documentation/devicetree/bindings/mfd/atmel-matrix.txt b/Documentation/devicetree/bindings/mfd/atmel-matrix.txt
new file mode 100644
index 0000000..405cac9
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-matrix.txt
@@ -0,0 +1,24 @@
+* Device tree bindings for Atmel Bus Matrix
+
+The Bus Matrix registers are used to configure Atmel SoCs internal bus
+behavior (master/slave priorities, undefined burst length type, ...)
+
+Required properties:
+- compatible:		should be one of the following
+			"atmel,at91sam9260-matrix", "syscon"
+			"atmel,at91sam9261-matrix", "syscon"
+			"atmel,at91sam9263-matrix", "syscon"
+			"atmel,at91sam9263-matrix", "syscon"
+			"atmel,at91sam9g45-matrix", "syscon"
+			"atmel,at91sam9n12-matrix", "syscon"
+			"atmel,at91sam9x5-matrix", "syscon"
+			"atmel,sama5d3-matrix", "syscon"
+- reg:			contains offset/length value of the Bus Matrix
+			memory region.
+
+Example:
+
+matrix: matrix@ffffec00 {
+	compatible = "atmel,sama5d3-matrix", "syscon";
+	reg = <0xffffec00 0x200>;
+};
-- 
1.9.1

[PATCH v2 03/11] mfd: syscon: Add atmel-smc registers definition

[Boris Brezillon]

Atmel AT91 SoCs have a memory range reserved for SMC (Static Memory
Controller) configuration.
Expose those registers so that drivers can make use of the smc syscon
declared in at91 DTs.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
---
 include/linux/mfd/syscon/atmel-smc.h | 60 ++++++++++++++++++++++++++++++++++++
 1 file changed, 60 insertions(+)
 create mode 100644 include/linux/mfd/syscon/atmel-smc.h

diff --git a/include/linux/mfd/syscon/atmel-smc.h b/include/linux/mfd/syscon/atmel-smc.h
new file mode 100644
index 0000000..430f486
--- /dev/null
+++ b/include/linux/mfd/syscon/atmel-smc.h
@@ -0,0 +1,60 @@
+/*
+ * Atmel SMC (Static Memory Controller) register offsets and bit definitions.
+ *
+ * Copyright (C) 2014 Atmel
+ * Copyright (C) 2014 Free Electrons
+ *
+ * Author: Boris Brezillon <boris.brezillon@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _LINUX_MFD_SYSCON_ATMEL_SMC_H_
+#define _LINUX_MFD_SYSCON_ATMEL_SMC_H_
+
+#include <linux/regmap.h>
+
+#define AT91SAM9_SMC_GENERIC_OFFSET	0x00
+#define AT91SAM9_SMC_GENERIC_BLK_SZ	0x10
+
+#define SAMA5_SMC_GENERIC_OFFSET	0x600
+#define SAMA5_SMC_GENERIC_BLK_SZ	0x14
+
+#define AT91SAM9_SMC_SETUP(o)		((o) + 0x00)
+#define AT91SAM9_SMC_NWESETUP_SHFT	0
+#define AT91SAM9_SMC_NCS_WRSETUP_SHFT	8
+#define AT91SAM9_SMC_NRDSETUP_SHFT	16
+#define AT91SAM9_SMC_NCS_NRDSETUP_SHFT	24
+
+#define AT91SAM9_SMC_PULSE(o)		((o) + 0x04)
+
+#define AT91SAM9_SMC_CYCLE(o)		((o) + 0x08)
+
+#define AT91SAM9_SMC_MODE(o)		((o) + 0x0c)
+#define SAMA5_SMC_MODE(o)		((o) + 0x10)
+#define AT91_SMC_READMODE		BIT(0)
+#define AT91_SMC_WRITEMODE		BIT(1)
+#define AT91_SMC_EXNWMODE		GENMASK(5, 4)
+#define AT91_SMC_EXNWMODE_DISABLE	(0 << 4)
+#define AT91_SMC_EXNWMODE_FROZEN	(2 << 4)
+#define AT91_SMC_EXNWMODE_READY		(3 << 4)
+#define AT91_SMC_BAT			BIT(8)
+#define AT91_SMC_BAT_SELECT		(0 << 8)
+#define AT91_SMC_BAT_WRITE		(1 << 8)
+#define AT91_SMC_DBW			GENMASK(13, 12)
+#define AT91_SMC_DBW_8			(0 << 12)
+#define AT91_SMC_DBW_16			(1 << 12)
+#define AT91_SMC_DBW_32			(2 << 12)
+#define AT91_SMC_TDF			GENMASK(19, 16)
+#define AT91_SMC_TDF_(x)		(((x) & 0xf) << 16)
+#define AT91_SMC_TDFMODE		BIT(20)
+#define AT91_SMC_PMEN			BIT(24)
+#define AT91_SMC_PS			GENMASK(29, 28)
+#define AT91_SMC_PS_4			(0 << 28)
+#define AT91_SMC_PS_8			(1 << 28)
+#define AT91_SMC_PS_16			(2 << 28)
+#define AT91_SMC_PS_32			(3 << 28)
+
+#endif /* _LINUX_MFD_SYSCON_ATMEL_SMC_H_ */
-- 
1.9.1

[PATCH v2 04/11] mfd: syscon: Add Atmel SMC binding doc

[Boris Brezillon]

The SMC registers are used to configure Atmel EBI (External Bus Interface)
to interface with standard memory devices (NAND, NOR, SRAM or specialized
devices like FPGAs).

Declare this memory region as a syscon, so that different drivers can
configure the SMC interface (mostly timing configuration) according to
their need.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
---
 Documentation/devicetree/bindings/mfd/atmel-smc.txt | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/atmel-smc.txt

diff --git a/Documentation/devicetree/bindings/mfd/atmel-smc.txt b/Documentation/devicetree/bindings/mfd/atmel-smc.txt
new file mode 100644
index 0000000..0c0cc3d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-smc.txt
@@ -0,0 +1,19 @@
+* Device tree bindings for Atmel SMC (Static Memory Controller)
+
+The SMC registers are used to configure Atmel EBI (External Bus Interface)
+to interface with standard memory devices (NAND, NOR, SRAM or specialized
+devices like FPGAs).
+
+Required properties:
+- compatible:		should be one of the following
+			"atmel,at91sam9260-smc", "syscon"
+			"atmel,sama5d3-smc", "syscon"
+- reg:			contains offset/length value of the SMC memory
+			region.
+
+Example:
+
+smc: smc@ffffc000 {
+	compatible = "atmel,sama5d3-smc", "syscon";
+	reg = <0xffffc000 0x1000>;
+};
-- 
1.9.1

[PATCH v2 05/11] memory: add Atmel EBI (External Bus Interface) driver

[Boris Brezillon]

The EBI (External Bus Interface) is used to access external peripherals
(NOR, SRAM, NAND, and other specific devices like ethernet controllers).
Each device is assigned a CS line and an address range and can have its
own configuration (timings, access mode, bus width, ...).
This driver provides a generic DT binding to configure a device according
to its requirements.
For specific device controllers (like the NAND one) the SMC timings
should be configured by the controller driver through the matrix and
smc syscon regmaps.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
---
 drivers/memory/Kconfig     |  11 +
 drivers/memory/Makefile    |   1 +
 drivers/memory/atmel-ebi.c | 615 +++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 627 insertions(+)
 create mode 100644 drivers/memory/atmel-ebi.c

diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
index 6d91c27..dfe24a2 100644
--- a/drivers/memory/Kconfig
+++ b/drivers/memory/Kconfig
@@ -17,6 +17,17 @@ config ATMEL_SDRAMC
 	  Starting with the at91sam9g45, this controller supports SDR, DDR and
 	  LP-DDR memories.
 
+config ATMEL_EBI
+	bool "Atmel EBI driver"
+	default y
+	depends on ARCH_AT91 && OF
+	select MFD_SYSCON
+	help
+	  Driver for Atmel EBI controller.
+	  Used to configure the EBI (external bus interface) when the device-
+	  tree is used. This bus supports NANDs, external ethernet controller,
+	  SRAMs, ATA devices, etc.
+
 config TI_AEMIF
 	tristate "Texas Instruments AEMIF driver"
 	depends on (ARCH_DAVINCI || ARCH_KEYSTONE) && OF
diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile
index c32d319..7ca2c19 100644
--- a/drivers/memory/Makefile
+++ b/drivers/memory/Makefile
@@ -6,6 +6,7 @@ ifeq ($(CONFIG_DDR),y)
 obj-$(CONFIG_OF)		+= of_memory.o
 endif
 obj-$(CONFIG_ATMEL_SDRAMC)	+= atmel-sdramc.o
+obj-$(CONFIG_ATMEL_EBI)		+= atmel-ebi.o
 obj-$(CONFIG_TI_AEMIF)		+= ti-aemif.o
 obj-$(CONFIG_TI_EMIF)		+= emif.o
 obj-$(CONFIG_FSL_CORENET_CF)	+= fsl-corenet-cf.o
diff --git a/drivers/memory/atmel-ebi.c b/drivers/memory/atmel-ebi.c
new file mode 100644
index 0000000..41bc893
--- /dev/null
+++ b/drivers/memory/atmel-ebi.c
@@ -0,0 +1,615 @@
+/*
+ * EBI driver for Atmel SAM9 chips
+ * inspired by the fsl weim bus driver
+ *
+ * Copyright (C) 2013 JJ Hiblot.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/atmel-matrix.h>
+#include <linux/mfd/syscon/atmel-smc.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+
+#define AT91SAM9_SMC_READ_MODE_MSK	BIT(0)
+#define AT91SAM9_SMC_READ_NCS_MODE	0
+#define AT91SAM9_SMC_READ_NRD_MODE	1
+#define AT91SAM9_SMC_WRITE_MODE_MSK	BIT(1)
+#define AT91SAM9_SMC_WRITE_NCS_MODE	(0 << 1)
+#define AT91SAM9_SMC_WRITE_NWE_MODE	(1 << 1)
+#define AT91SAM9_SMC_EXNW_MODE_MSK	GENMASK(5, 4)
+#define AT91SAM9_SMC_EXNW_DIS		(0 << 4)
+#define AT91SAM9_SMC_EXNW_FROZEN	(2 << 4)
+#define AT91SAM9_SMC_EXNW_READY		(3 << 4)
+#define AT91SAM9_SMC_BAT_MSK		BIT(8)
+#define AT91SAM9_SMC_BAT_SELECT		(0 << 8)
+#define AT91SAM9_SMC_BAT_WRITE		(1 << 8)
+#define AT91SAM9_SMC_DBW_MSK		GENMASK(13, 12)
+#define AT91SAM9_SMC_DBW(x)		((((x) / 16) & 0x3) << 12)
+#define AT91SAM9_SMC_TDF_CYCLES_MSK	GENMASK(19, 16)
+#define AT91SAM9_SMC_TDF_CYCLES(x)	(((x) & 0xf) << 16)
+#define AT91SAM9_SMC_TDF_MODE_MSK	BIT(20)
+#define AT91SAM9_SMC_TDF_OPTIMIZED	(1 << 20)
+#define AT91SAM9_SMC_PMEN		BIT(24)
+#define AT91SAM9_SMC_PS(x)		((((x) / 4) & 0x3) << 28)
+
+#define AT91_EBICSA_REGFIELD(soc)			\
+	REG_FIELD(soc ## _MATRIX_EBICSA_OFF, 0,		\
+		  AT91_MATRIX_EBI_NUM_CS - 1)
+
+#define AT91_MULTI_EBICSA_REGFIELD(soc, n)		\
+	REG_FIELD(soc ## _MATRIX_EBI ## n ## CSA_OFF,	\
+		  0, AT91_MATRIX_EBI_NUM_CS - 1)
+
+struct at91sam9_smc_timings {
+	u32 ncs_rd_setup_ns;
+	u32 nrd_setup_ns;
+	u32 ncs_wr_setup_ns;
+	u32 nwe_setup_ns;
+	u32 ncs_rd_pulse_ns;
+	u32 nrd_pulse_ns;
+	u32 ncs_wr_pulse_ns;
+	u32 nwe_pulse_ns;
+	u32 nrd_cycle_ns;
+	u32 nwe_cycle_ns;
+	u32 tdf_ns;
+};
+
+struct at91sam9_smc_generic_fields {
+	struct regmap_field *setup;
+	struct regmap_field *pulse;
+	struct regmap_field *cycle;
+	struct regmap_field *mode;
+};
+
+struct at91sam9_ebi_dev_config {
+	struct at91sam9_smc_timings timings;
+	u32 mode;
+};
+
+struct at91_ebi;
+
+struct at91_ebi_dev {
+	struct device_node *np;
+	struct at91_smc_timings *timings;
+	struct at91_ebi *ebi;
+	u32 mode;
+	int cs;
+	void *config;
+};
+
+struct at91_ebi_caps {
+	unsigned int available_cs;
+	const struct reg_field *ebi_csa;
+	int (*xlate_config)(struct at91_ebi_dev *ebid);
+	int (*apply_config)(struct at91_ebi_dev *ebid);
+	int (*init)(struct at91_ebi *ebi);
+};
+
+struct at91_ebi {
+	struct clk *clk;
+	struct regmap *smc;
+	struct regmap *matrix;
+
+	struct regmap_field *ebi_csa;
+
+	struct device *dev;
+	const struct at91_ebi_caps *caps;
+	struct at91_ebi_dev *devs[AT91_MATRIX_EBI_NUM_CS];
+	void *priv;
+};
+
+static u32 at91sam9_smc_setup_ns_to_cycles(unsigned int clk_rate,
+					   u32 timing_ns)
+{
+	u32 clk_period = DIV_ROUND_UP(NSEC_PER_SEC, clk_rate);
+	u32 coded_cycles = 0;
+	u32 cycles;
+
+	cycles = DIV_ROUND_UP(timing_ns, clk_period);
+	if (cycles / 32) {
+		coded_cycles |= 1 << 5;
+		if (cycles < 128)
+			cycles = 0;
+	}
+
+	coded_cycles |= cycles % 32;
+
+	return coded_cycles;
+}
+
+static u32 at91sam9_smc_pulse_ns_to_cycles(unsigned int clk_rate,
+					   u32 timing_ns)
+{
+	u32 clk_period = DIV_ROUND_UP(NSEC_PER_SEC, clk_rate);
+	u32 coded_cycles = 0;
+	u32 cycles;
+
+	cycles = DIV_ROUND_UP(timing_ns, clk_period);
+	if (cycles / 64) {
+		coded_cycles |= 1 << 6;
+		if (cycles < 256)
+			cycles = 0;
+	}
+
+	coded_cycles |= cycles % 64;
+
+	return coded_cycles;
+}
+
+static u32 at91sam9_smc_cycle_ns_to_cycles(unsigned int clk_rate,
+					   u32 timing_ns)
+{
+	u32 clk_period = DIV_ROUND_UP(NSEC_PER_SEC, clk_rate);
+	u32 coded_cycles = 0;
+	u32 cycles;
+
+	cycles = DIV_ROUND_UP(timing_ns, clk_period);
+	if (cycles / 128) {
+		coded_cycles = cycles / 256;
+		cycles %= 256;
+		if (cycles >= 128) {
+			coded_cycles++;
+			cycles = 0;
+		}
+
+		if (coded_cycles > 0x3) {
+			coded_cycles = 0x3;
+			cycles = 0x7f;
+		}
+
+		coded_cycles <<= 7;
+	}
+
+	coded_cycles |= cycles % 128;
+
+	return coded_cycles;
+}
+
+static int at91sam9_ebi_apply_config(struct at91_ebi_dev *ebid)
+{
+	unsigned int clk_rate = clk_get_rate(ebid->ebi->clk);
+	struct at91sam9_ebi_dev_config *config = ebid->config;
+	struct at91sam9_smc_timings *timings = &config->timings;
+	struct at91sam9_smc_generic_fields *fields = ebid->ebi->priv;
+	u32 val;
+
+	val = at91sam9_smc_setup_ns_to_cycles(clk_rate,
+					      timings->ncs_rd_setup_ns) << 24;
+	val |= at91sam9_smc_setup_ns_to_cycles(clk_rate,
+					       timings->nrd_setup_ns) << 16;
+	val |= at91sam9_smc_setup_ns_to_cycles(clk_rate,
+					       timings->ncs_wr_setup_ns) << 8;
+	val |= at91sam9_smc_setup_ns_to_cycles(clk_rate,
+					       timings->nwe_setup_ns);
+	regmap_fields_write(fields->setup, ebid->cs, val);
+
+	val = at91sam9_smc_pulse_ns_to_cycles(clk_rate,
+					      timings->ncs_rd_pulse_ns) << 24;
+	val |= at91sam9_smc_pulse_ns_to_cycles(clk_rate,
+					       timings->nrd_pulse_ns) << 16;
+	val |= at91sam9_smc_pulse_ns_to_cycles(clk_rate,
+					       timings->ncs_wr_pulse_ns) << 8;
+	val |= at91sam9_smc_pulse_ns_to_cycles(clk_rate,
+					       timings->nwe_pulse_ns);
+	regmap_fields_write(fields->pulse, ebid->cs, val);
+
+	val = at91sam9_smc_cycle_ns_to_cycles(clk_rate,
+					      timings->nrd_cycle_ns) << 16;
+	val |= at91sam9_smc_cycle_ns_to_cycles(clk_rate,
+					       timings->nwe_cycle_ns);
+	regmap_fields_write(fields->cycle, ebid->cs, val);
+
+	val = DIV_ROUND_UP(timings->tdf_ns, clk_rate);
+	if (val > 16)
+		val = 16;
+	regmap_fields_write(fields->mode, ebid->cs, config->mode | val << 16);
+
+	return 0;
+}
+
+static int at91sam9_smc_xslate_timings(struct at91_ebi_dev *ebid)
+{
+	struct at91sam9_ebi_dev_config *config = ebid->config;
+	struct at91sam9_smc_timings *timings;
+	struct device_node *np = ebid->np;
+
+	timings = &config->timings;
+
+	of_property_read_u32(np, "atmel,ncs-rd-setup-ns",
+			     &timings->ncs_rd_setup_ns);
+	of_property_read_u32(np, "atmel,nrd-setup-ns",
+			     &timings->nrd_setup_ns);
+	of_property_read_u32(np, "atmel,ncs-wr-setup-ns",
+			     &timings->ncs_wr_setup_ns);
+	of_property_read_u32(np, "atmel,nwe-setup-ns",
+			     &timings->nwe_setup_ns);
+	of_property_read_u32(np, "atmel,ncs-rd-pulse-ns",
+			     &timings->ncs_rd_pulse_ns);
+	of_property_read_u32(np, "atmel,nrd-pulse-ns",
+			     &timings->nrd_pulse_ns);
+	of_property_read_u32(np, "atmel,ncs-wr-pulse-ns",
+			     &timings->ncs_wr_pulse_ns);
+	of_property_read_u32(np, "atmel,nwe-pulse-ns", &timings->nwe_pulse_ns);
+	of_property_read_u32(np, "atmel,nwe-cycle-ns", &timings->nwe_cycle_ns);
+	of_property_read_u32(np, "atmel,nrd-cycle-ns", &timings->nrd_cycle_ns);
+	of_property_read_u32(np, "atmel,tdf-ns", &timings->tdf_ns);
+
+	return 0;
+}
+
+static int at91sam9_ebi_xslate_config(struct at91_ebi_dev *ebid)
+{
+	struct at91sam9_ebi_dev_config *config = ebid->config;
+	struct device_node *np = ebid->np;
+	const char *tmp_str;
+	u32 tmp;
+	int ret;
+
+	config = devm_kzalloc(ebid->ebi->dev, sizeof(*config), GFP_KERNEL);
+	if (!config)
+		return -ENOMEM;
+
+	ebid->config = config;
+
+	ret = of_property_read_u32(np, "atmel,bus-width", &tmp);
+	if (ret)
+		return ret;
+
+	if (tmp != 8 && tmp != 16 && tmp != 32)
+		return -EINVAL;
+
+	config->mode |= AT91SAM9_SMC_DBW(tmp);
+
+	if (of_property_read_bool(np, "atmel,tdf-optimized"))
+		config->mode |= AT91SAM9_SMC_TDF_OPTIMIZED;
+
+	tmp_str = NULL;
+	of_property_read_string(np, "atmel,byte-access-type", &tmp_str);
+	if (tmp_str && !strcmp(tmp_str, "write"))
+		config->mode |= AT91SAM9_SMC_BAT_WRITE;
+
+	tmp_str = NULL;
+	of_property_read_string(np, "atmel,read-mode", &tmp_str);
+	if (tmp_str && !strcmp(tmp_str, "nrd"))
+		config->mode |= AT91SAM9_SMC_READ_NRD_MODE;
+
+	tmp_str = NULL;
+	of_property_read_string(np, "atmel,write-mode", &tmp_str);
+	if (tmp_str && !strcmp(tmp_str, "nwe"))
+		config->mode |= AT91SAM9_SMC_WRITE_NWE_MODE;
+
+	tmp_str = NULL;
+	of_property_read_string(np, "atmel,exnw-mode", &tmp_str);
+	if (tmp_str) {
+		if (!strcmp(tmp_str, "frozen"))
+			config->mode |= AT91SAM9_SMC_EXNW_FROZEN;
+		else if (!strcmp(tmp_str, "ready"))
+			config->mode |= AT91SAM9_SMC_EXNW_READY;
+	}
+
+	tmp = 0;
+	of_property_read_u32(np, "atmel,page-mode", &tmp);
+	if (tmp)
+		config->mode |= AT91SAM9_SMC_PS(tmp) | AT91SAM9_SMC_PMEN;
+
+	return at91sam9_smc_xslate_timings(ebid);
+}
+
+static int at91sam9_ebi_init(struct at91_ebi *ebi)
+{
+	struct at91sam9_smc_generic_fields *fields;
+	struct reg_field field = REG_FIELD(0, 0, 31);
+
+	fields = devm_kzalloc(ebi->dev, sizeof(*fields), GFP_KERNEL);
+	if (!fields)
+		return -ENOMEM;
+
+	field.id_size = fls(ebi->caps->available_cs);
+	field.id_offset = 0x10;
+
+	field.reg = AT91SAM9_SMC_SETUP(AT91SAM9_SMC_GENERIC_OFFSET);
+	fields->setup = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->setup))
+		return PTR_ERR(fields->setup);
+
+	field.reg = AT91SAM9_SMC_PULSE(AT91SAM9_SMC_GENERIC_OFFSET);
+	fields->pulse = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->pulse))
+		return PTR_ERR(fields->pulse);
+
+	field.reg = AT91SAM9_SMC_CYCLE(AT91SAM9_SMC_GENERIC_OFFSET);
+	fields->cycle = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->cycle))
+		return PTR_ERR(fields->cycle);
+
+	field.reg = AT91SAM9_SMC_MODE(AT91SAM9_SMC_GENERIC_OFFSET);
+	fields->mode = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->mode))
+		return PTR_ERR(fields->mode);
+
+	ebi->priv = fields;
+
+	return 0;
+}
+
+static int sama5d3_ebi_init(struct at91_ebi *ebi)
+{
+	struct at91sam9_smc_generic_fields *fields;
+	struct reg_field field = REG_FIELD(0, 0, 31);
+
+	fields = devm_kzalloc(ebi->dev, sizeof(*fields), GFP_KERNEL);
+	if (!fields)
+		return -ENOMEM;
+
+	field.id_size = fls(ebi->caps->available_cs);
+	field.id_offset = SAMA5_SMC_GENERIC_BLK_SZ;
+
+	field.reg = AT91SAM9_SMC_SETUP(SAMA5_SMC_GENERIC_OFFSET);
+	fields->setup = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->setup))
+		return PTR_ERR(fields->setup);
+
+	field.reg = AT91SAM9_SMC_PULSE(SAMA5_SMC_GENERIC_OFFSET);
+	fields->pulse = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->pulse))
+		return PTR_ERR(fields->pulse);
+
+	field.reg = AT91SAM9_SMC_CYCLE(SAMA5_SMC_GENERIC_OFFSET);
+	fields->cycle = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->cycle))
+		return PTR_ERR(fields->cycle);
+
+	field.reg = SAMA5_SMC_MODE(SAMA5_SMC_GENERIC_OFFSET);
+	fields->mode = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->mode))
+		return PTR_ERR(fields->mode);
+
+	ebi->priv = fields;
+
+	return 0;
+}
+
+static int at91_ebi_dev_setup(struct at91_ebi *ebi, struct device_node *np)
+{
+	struct device *dev = ebi->dev;
+	struct device_node *dev_np;
+	struct at91_ebi_dev *ebid;
+	u32 tmp;
+	int ret;
+
+	dev_np = of_get_next_child(np, NULL);
+	if (!dev_np)
+		return -EINVAL;
+
+	if (!of_device_is_available(dev_np))
+		return 0;
+
+	ebid = devm_kzalloc(ebi->dev, sizeof(*ebid), GFP_KERNEL);
+	if (!ebid)
+		return -ENOMEM;
+
+	ret = of_property_read_u32(dev_np, "reg" , &tmp);
+	if (ret < 0) {
+		dev_err(dev, "missing mandatory reg property\n");
+		return ret;
+	}
+
+	if (tmp > AT91_MATRIX_EBI_NUM_CS ||
+	    !(BIT(tmp) & ebi->caps->available_cs)) {
+		dev_err(dev, "invalid reg property\n");
+		return -EINVAL;
+	}
+
+	ebid->cs = tmp;
+	ebid->np = np;
+	ebid->ebi = ebi;
+
+	if (!of_property_read_bool(np, "atmel,generic-dev"))
+		goto populate;
+
+	if (ebid->ebi->ebi_csa)
+		regmap_field_update_bits(ebid->ebi->ebi_csa,
+					 BIT(ebid->cs),
+					 ~BIT(ebid->cs));
+
+	ret = ebid->ebi->caps->xlate_config(ebid);
+	if (ret)
+		return ret;
+
+	ret = ebid->ebi->caps->apply_config(ebid);
+	if (ret)
+		return ret;
+	ebi->devs[ebid->cs] = ebid;
+
+populate:
+	return of_platform_populate(np, of_default_bus_match_table, NULL, dev);
+}
+
+static const struct reg_field at91sam9260_ebi_csa =
+				AT91_EBICSA_REGFIELD(AT91SAM9260);
+
+static const struct at91_ebi_caps at91sam9260_ebi_caps = {
+	.available_cs = 0xff,
+	.ebi_csa = &at91sam9260_ebi_csa,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9261_ebi_csa =
+				AT91_EBICSA_REGFIELD(AT91SAM9261);
+
+static const struct at91_ebi_caps at91sam9261_ebi_caps = {
+	.available_cs = 0xff,
+	.ebi_csa = &at91sam9261_ebi_csa,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9263_ebi0_csa =
+				AT91_MULTI_EBICSA_REGFIELD(AT91SAM9263, 0);
+
+static const struct at91_ebi_caps at91sam9263_ebi0_caps = {
+	.available_cs = 0x3f,
+	.ebi_csa = &at91sam9263_ebi0_csa,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9263_ebi1_csa =
+				AT91_MULTI_EBICSA_REGFIELD(AT91SAM9263, 1);
+
+static const struct at91_ebi_caps at91sam9263_ebi1_caps = {
+	.available_cs = 0x7,
+	.ebi_csa = &at91sam9263_ebi1_csa,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9g45_ebi_csa =
+				AT91_EBICSA_REGFIELD(AT91SAM9G45);
+
+static const struct at91_ebi_caps at91sam9g45_ebi_caps = {
+	.available_cs = 0x3f,
+	.ebi_csa = &at91sam9g45_ebi_csa,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = at91sam9_ebi_init,
+};
+
+static const struct at91_ebi_caps at91sam9x5_ebi_caps = {
+	.available_cs = 0x3f,
+	.ebi_csa = &at91sam9263_ebi0_csa,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = at91sam9_ebi_init,
+};
+
+static const struct at91_ebi_caps sama5d3_ebi_caps = {
+	.available_cs = 0xf,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = sama5d3_ebi_init,
+};
+
+static const struct of_device_id at91_ebi_id_table[] = {
+	{
+		.compatible = "atmel,at91sam9260-ebi",
+		.data = &at91sam9260_ebi_caps,
+	},
+	{
+		.compatible = "atmel,at91sam9261-ebi",
+		.data = &at91sam9261_ebi_caps,
+	},
+	{
+		.compatible = "atmel,at91sam9263-ebi0",
+		.data = &at91sam9263_ebi0_caps,
+	},
+	{
+		.compatible = "atmel,at91sam9263-ebi1",
+		.data = &at91sam9263_ebi1_caps,
+	},
+	{
+		.compatible = "atmel,at91sam9g45-ebi",
+		.data = &at91sam9g45_ebi_caps,
+	},
+	{
+		.compatible = "atmel,at91sam9x5-ebi",
+		.data = &at91sam9x5_ebi_caps,
+	},
+	{
+		.compatible = "atmel,sama5d3-ebi",
+		.data = &sama5d3_ebi_caps,
+	},
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, at91_ebi_id_table);
+
+static int at91_ebi_probe(struct platform_device *pdev)
+{
+	const struct of_device_id *match;
+	struct device_node *child;
+	struct device_node *np;
+	struct at91_ebi *ebi;
+	struct clk *clk;
+	int ret;
+
+	match = of_match_device(at91_ebi_id_table, &pdev->dev);
+	if (!match || !match->data)
+		return -EINVAL;
+
+	ebi = devm_kzalloc(&pdev->dev, sizeof(*ebi), GFP_KERNEL);
+	if (!ebi)
+		return -ENOMEM;
+
+	ebi->caps = match->data;
+	ebi->dev = &pdev->dev;
+
+	clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+
+	ebi->clk = clk;
+
+	np = of_parse_phandle(pdev->dev.of_node, "atmel,smc", 0);
+	if (!np)
+		return -EINVAL;
+
+	ebi->smc = syscon_node_to_regmap(np);
+	if (IS_ERR(ebi->smc))
+		return PTR_ERR(ebi->smc);
+
+	/*
+	 * The sama5d3 does not provide an EBICSA register and thus does need
+	 * to access the matrix registers.
+	 */
+	if (ebi->caps->ebi_csa) {
+		np = of_parse_phandle(pdev->dev.of_node, "atmel,matrix", 0);
+		if (np)
+			return -EINVAL;
+
+		ebi->matrix = syscon_node_to_regmap(np);
+		if (IS_ERR(ebi->matrix))
+			return PTR_ERR(ebi->matrix);
+
+		ebi->ebi_csa = regmap_field_alloc(ebi->matrix,
+						  *ebi->caps->ebi_csa);
+		if (IS_ERR(ebi->ebi_csa))
+			return PTR_ERR(ebi->ebi_csa);
+	}
+
+	ret = ebi->caps->init(ebi);
+	if (ret)
+		return ret;
+
+	for_each_child_of_node(pdev->dev.of_node, child) {
+		ret = at91_ebi_dev_setup(ebi, child);
+		if (ret)
+			return ret;
+	}
+
+	return ret;
+}
+
+static struct platform_driver at91_ebi_driver = {
+	.driver = {
+		.name = "atmel-ebi",
+		.of_match_table	= at91_ebi_id_table,
+	},
+};
+module_platform_driver_probe(at91_ebi_driver, at91_ebi_probe);
+
+MODULE_AUTHOR("JJ Hiblot");
+MODULE_DESCRIPTION("Atmel's EBI driver");
+MODULE_LICENSE("GPL");
-- 
1.9.1

[PATCH v2 06/11] memory: atmel-ebi: add DT bindings documentation

[Boris Brezillon]

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
---
 .../bindings/memory-controllers/atmel-ebi.txt      | 153 +++++++++++++++++++++
 1 file changed, 153 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt

diff --git a/Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt b/Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt
new file mode 100644
index 0000000..dc2c34f
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt
@@ -0,0 +1,153 @@
+* Device tree bindings for Atmel EBI
+
+The External Bus Interface (EBI) controller is a bus where you can connect
+asynchronous (NAND, NOR, SRAM, ....) and synchronous memories (SDR/DDR SDRAMs).
+The EBI provides a glue-less interface to asynchronous memories though the SMC
+(Static Memory Controller).
+Synchronous memories (and some asynchronous memories like NANDs) can be
+attached to specialized controllers which are responsible for configuring the
+bus appropriately according to the connected device.
+In the other hand, the bus interface can be automated for simple asynchronous
+devices.
+
+Required properties:
+
+- compatible:		"atmel,at91sam9260-ebi"
+			"atmel,at91sam9261-ebi"
+			"atmel,at91sam9263-ebi0"
+			"atmel,at91sam9263-ebi1"
+			"atmel,at91sam9g45-ebi"
+			"atmel,at91sam9x5-ebi"
+			"atmel,sama5d3-ebi"
+
+- reg:			Contains offset/length value for EBI memory mapping.
+			This property might contain several entries if the EBI
+			memory range is not contiguous
+
+- #address-cells:	Must be 2.
+			The first cell encodes the CS.
+			The second cell encode the offset into the CS memory
+			range.
+
+- #size-cells:		Must be set to 1.
+
+- ranges:		Encodes CS to memory region association.
+
+- clocks:		Clock feeding the EBI controller.
+			See clock-bindings.txt
+
+Child chip-select (cs) nodes contain the memory devices nodes connected to
+such as NOR (e.g. cfi-flash) and NAND.
+There might be board specific devices like FPGAs.
+You'll define you device requirements in these child nodes.
+
+Required child cs node properties:
+
+- #address-cells:	Must be 2.
+
+- #size-cells:		Must be 1.
+
+- ranges:		Empty property indicating that child nodes can inherit
+			memory layout.
+
+Optional child cs node properties:
+- atmel,generic-dev		boolean property specifying if the device is
+				a generic device.
+				The following properties are only parsed if
+				this property is present.
+				Specialized devices are attached to specialized
+				controllers which should configure the bus
+				appropriately.
+
+- atmel,bus-width:		width of the asynchronous device's data bus
+				8, 16 or 32.
+				8 if not present.
+
+- atmel,byte-access-type	"write" or "select" (see Atmel datasheet).
+				"select" if not present.
+
+- atmel,read-mode		"nrd" or "ncs".
+				"ncs" is not present.
+
+- atmel,write-mode		"nwe" or "ncs".
+				"ncs" is not present.
+
+- atmel,exnw-mode		"disabled", "frozen" or "ready".
+				"disabled" if not present.
+
+- atmel,page-mode		enable page mode if present. The provided value
+				defines the page size (supported values: 4, 8,
+				16 and 32).
+
+Optional device timings expressed in nanoseconds (if the property is not
+present 0 is assumed):
+
+- atmel,ncs-rd-setup-ns
+- atmel,nrd-setup-ns
+- atmel,ncs-wr-setup-ns
+- atmel,nwe-setup-ns
+- atmel,ncs-rd-pulse-ns
+- atmel,nrd-pulse-ns
+- atmel,ncs-wr-pulse-ns
+- atmel,nwe-pulse-ns
+- atmel,nwe-cycle-ns
+- atmel,nrd-cycle-ns
+- atmel,tdf-ns
+
+- atmel,tdf-optimized		data float optimized mode. If present the data
+				float time is optimized depending on the next
+				device being accessed (next device setup
+				time is substracted to the current devive data
+				float time).
+
+
+
+Example:
+
+	ebi: ebi@10000000 {
+		compatible = "atmel,sama5d3-ebi", "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		atmel,smc = <&hsmc>;
+		atmel,matrix = <&matrix>;
+		reg = <0x10000000 0x10000000
+		       0x40000000 0x30000000>;
+		ranges = <0x0 0x0 0x10000000 0x10000000
+			  0x1 0x0 0x40000000 0x10000000
+			  0x2 0x0 0x50000000 0x10000000
+			  0x3 0x0 0x60000000 0x10000000>;
+		clocks = <&mck>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ebi_addr>;
+
+		cs@0 {
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges;
+			atmel,generic-dev;
+			atmel,read-mode = "nrd";
+			atmel,write-mode = "nwe";
+			atmel,bus-width = <16>;
+			atmel,ncs-rd-setup-ns = <0>;
+			atmel,ncs-wr-setup-ns = <0>;
+			atmel,nwe-setup-ns = <8>;
+			atmel,nrd-setup-ns = <16>;
+			atmel,ncs-rd-pulse-ns = <84>;
+			atmel,ncs-wr-pulse-ns = <84>;
+			atmel,nrd-pulse-ns = <76>;
+			atmel,nwe-pulse-ns = <76>;
+			atmel,nrd-cycle-ns = <107>;
+			atmel,nwe-cycle-ns = <84>;
+			atmel,tdf-ns = <16>;
+
+			nor: flash@0,0 {
+				compatible = "cfi-flash";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0x0 0x0 0x1000000>;
+				bank-width = <2>;
+			};
+		};
+	};
+
-- 
1.9.1

[PATCH v2 07/11] ARM: at91: select ATMEL_EBI when compiling a kernel for at91sam9 or sama5d3

[Boris Brezillon]

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
---
 arch/arm/mach-at91/Kconfig | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 0e6d548..a72402a 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -49,6 +49,7 @@ config SOC_AT91SAM9
 	select GENERIC_CLOCKEVENTS
 	select MEMORY if USE_OF
 	select ATMEL_SDRAMC if USE_OF
+	select ATMEL_EBI if USE_OF
 
 config SOC_SAMA5
 	bool
@@ -58,6 +59,7 @@ config SOC_SAMA5
 	select USE_OF
 	select MEMORY
 	select ATMEL_SDRAMC
+	select ATMEL_EBI
 
 menu "Atmel AT91 System-on-Chip"
 
-- 
1.9.1

[PATCH v2 08/11] ARM: at91/dt: add HSMC (Static Memory Controller) node in sama5d3 dtsi

[Boris Brezillon]

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
---
 arch/arm/boot/dts/sama5d3.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index 5f4144d..9f1eed5 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -395,6 +395,11 @@
 				clock-names = "tdes_clk";
 			};
 
+			hsmc: hsmc@ffffc000 {
+				compatible = "atmel,sama5d3-smc", "syscon";
+				reg = <0xffffc000 0x1000>;
+			};
+
 			dma0: dma-controller@ffffe600 {
 				compatible = "atmel,at91sam9g45-dma";
 				reg = <0xffffe600 0x200>;
-- 
1.9.1

[PATCH v2 09/11] ARM: at91/dt: add matrix node in sama5d3 dtsi

[Boris Brezillon]

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
---
 arch/arm/boot/dts/sama5d3.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index 9f1eed5..d49dab7 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -425,6 +425,11 @@
 				clock-names = "ddrck", "mpddr";
 			};
 
+			matrix: matrix@ffffec00 {
+				compatible = "atmel,sama5d3-matrix", "syscon";
+				reg = <0xffffec00 0x200>;
+			};
+
 			dbgu: serial@ffffee00 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xffffee00 0x200>;
-- 
1.9.1

[PATCH v2 10/11] ARM: at91/dt: add EBI (External Bus Interface) node in sama5d3 dtsi

[Boris Brezillon]

Add EBI node and EBI pin muxing.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
---
 arch/arm/boot/dts/sama5d3.dtsi | 83 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 83 insertions(+)

diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index d49dab7..d011ade 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -530,6 +530,63 @@
 					};
 				};
 
+				ebi {
+					pinctrl_ebi_addr: ebi-addr-0 {
+						atmel,pins =
+							<AT91_PIOE 0 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 1 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 2 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 3 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 4 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 5 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 6 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 7 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 8 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 9 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 10 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 11 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 12 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 13 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 14 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 15 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 16 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 17 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 18 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 19 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 20 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 21 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 22 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 23 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 24 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOE 25 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_ebi_cs0: ebi-cs0-0 {
+						atmel,pins =
+							<AT91_PIOE 26 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_ebi_cs1: ebi-cs1-0 {
+						atmel,pins =
+							<AT91_PIOE 27 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_ebi_cs2: ebi-cs2-0 {
+						atmel,pins =
+							<AT91_PIOE 28 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_ebi_nwr1_nbs1: ebi-nwr1-nbs1-0 {
+						atmel,pins =
+							<AT91_PIOE 29 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_ebi_nwait: ebi-nwait-0 {
+						atmel,pins =
+							<AT91_PIOE 30 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+				};
+
 				i2c0 {
 					pinctrl_i2c0: i2c0-0 {
 						atmel,pins =
@@ -1407,6 +1464,32 @@
 			status = "disabled";
 		};
 
+		ebi: ebi@10000000 {
+			compatible = "atmel,sama5d3-ebi", "simple-bus";
+			#address-cells = <2>;
+			#size-cells = <1>;
+			atmel,smc = <&hsmc>;
+			atmel,matrix = <&matrix>;
+			reg = <0x10000000 0x10000000
+			       0x40000000 0x30000000>;
+			ranges = <0x0 0x0 0x10000000 0x10000000
+				  0x1 0x0 0x40000000 0x10000000
+				  0x2 0x0 0x50000000 0x10000000
+				  0x3 0x0 0x60000000 0x10000000>;
+			clocks = <&mck>;
+
+			/*
+			 * TODO: EBI pins should be referenced here, but they
+			 * conflict with NAND pins, which should actually be a
+			 * sub device of the EBI bus and thus should not
+			 * request it's own set of pins as they are shared
+			 * with other devices connected on the EBI bus.
+			 *
+			 * pinctrl-names = "default";
+			 * pinctrl-0 = <&pinctrl_ebi_addr>;
+			 */
+		};
+
 		nand0: nand@60000000 {
 			compatible = "atmel,at91rm9200-nand";
 			#address-cells = <1>;
-- 
1.9.1

[PATCH v2 11/11] ARM: at91/dt: add NOR definition in sama5d3xcm dtsi

[Boris Brezillon]

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
---
 arch/arm/boot/dts/sama5d3xcm.dtsi | 34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm/boot/dts/sama5d3xcm.dtsi b/arch/arm/boot/dts/sama5d3xcm.dtsi
index 962dc28..857ef05 100644
--- a/arch/arm/boot/dts/sama5d3xcm.dtsi
+++ b/arch/arm/boot/dts/sama5d3xcm.dtsi
@@ -75,6 +75,40 @@
 			};
 		};
 
+		ebi@10000000 {
+			pinctrl-0 = <&pinctrl_ebi_addr &pinctrl_ebi_cs0>;
+
+			cs@0 {
+				#address-cells = <2>;
+				#size-cells = <1>;
+				ranges;
+				atmel,generic-dev;
+				atmel,read-mode = "nrd";
+				atmel,write-mode = "nwe";
+				atmel,bus-width = <16>;
+				atmel,ncs-rd-setup-ns = <0>;
+				atmel,ncs-wr-setup-ns = <0>;
+				atmel,nwe-setup-ns = <8>;
+				atmel,nrd-setup-ns = <16>;
+				atmel,ncs-rd-pulse-ns = <84>;
+				atmel,ncs-wr-pulse-ns = <84>;
+				atmel,nrd-pulse-ns = <76>;
+				atmel,nwe-pulse-ns = <76>;
+				atmel,nrd-cycle-ns = <107>;
+				atmel,nwe-cycle-ns = <84>;
+				atmel,tdf-ns = <16>;
+
+				nor: flash@0,0 {
+					compatible = "cfi-flash";
+					linux,mtd-name = "physmap-flash.0";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					reg = <0x0 0x0 0x1000000>;
+					bank-width = <2>;
+				};
+			};
+		};
+
 		nand0: nand@60000000 {
 			nand-bus-width = <8>;
 			nand-ecc-mode = "hw";
-- 
1.9.1

Re: [PATCH v2 06/11] memory: atmel-ebi: add DT bindings documentation

[Jean-Jacques Hiblot]

Hi Boris,

2014-11-05 17:01 GMT+01:00 Boris Brezillon <boris.brezillon@free-electrons.com>:
> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> ---
>  .../bindings/memory-controllers/atmel-ebi.txt      | 153 +++++++++++++++++++++
>  1 file changed, 153 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt
>
> diff --git a/Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt b/Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt
> new file mode 100644
> index 0000000..dc2c34f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt
> @@ -0,0 +1,153 @@
> +* Device tree bindings for Atmel EBI
> +
> +The External Bus Interface (EBI) controller is a bus where you can connect
> +asynchronous (NAND, NOR, SRAM, ....) and synchronous memories (SDR/DDR SDRAMs).
> +The EBI provides a glue-less interface to asynchronous memories though the SMC
> +(Static Memory Controller).
> +Synchronous memories (and some asynchronous memories like NANDs) can be
> +attached to specialized controllers which are responsible for configuring the
> +bus appropriately according to the connected device.
> +In the other hand, the bus interface can be automated for simple asynchronous
> +devices.
> +
> +Required properties:
> +
> +- compatible:          "atmel,at91sam9260-ebi"
> +                       "atmel,at91sam9261-ebi"
> +                       "atmel,at91sam9263-ebi0"
> +                       "atmel,at91sam9263-ebi1"
> +                       "atmel,at91sam9g45-ebi"
> +                       "atmel,at91sam9x5-ebi"
> +                       "atmel,sama5d3-ebi"
> +
> +- reg:                 Contains offset/length value for EBI memory mapping.
> +                       This property might contain several entries if the EBI
> +                       memory range is not contiguous
> +
> +- #address-cells:      Must be 2.
> +                       The first cell encodes the CS.
> +                       The second cell encode the offset into the CS memory
> +                       range.
> +
> +- #size-cells:         Must be set to 1.
> +
> +- ranges:              Encodes CS to memory region association.
> +
> +- clocks:              Clock feeding the EBI controller.
> +                       See clock-bindings.txt
> +
> +Child chip-select (cs) nodes contain the memory devices nodes connected to
> +such as NOR (e.g. cfi-flash) and NAND.
> +There might be board specific devices like FPGAs.
> +You'll define you device requirements in these child nodes.
> +
> +Required child cs node properties:
> +
> +- #address-cells:      Must be 2.
> +
> +- #size-cells:         Must be 1.
> +
> +- ranges:              Empty property indicating that child nodes can inherit
> +                       memory layout.
> +
> +Optional child cs node properties:
> +- atmel,generic-dev            boolean property specifying if the device is
> +                               a generic device.
> +                               The following properties are only parsed if
> +                               this property is present.
> +                               Specialized devices are attached to specialized
> +                               controllers which should configure the bus
> +                               appropriately.

What do you mean by specialized devices ? Can you give an example ?

> +
> +- atmel,bus-width:             width of the asynchronous device's data bus
> +                               8, 16 or 32.
> +                               8 if not present.
> +
> +- atmel,byte-access-type       "write" or "select" (see Atmel datasheet).
> +                               "select" if not present.
> +
> +- atmel,read-mode              "nrd" or "ncs".
> +                               "ncs" is not present.
> +
> +- atmel,write-mode             "nwe" or "ncs".
> +                               "ncs" is not present.
> +
> +- atmel,exnw-mode              "disabled", "frozen" or "ready".
> +                               "disabled" if not present.
> +
> +- atmel,page-mode              enable page mode if present. The provided value
> +                               defines the page size (supported values: 4, 8,
> +                               16 and 32).
> +
> +Optional device timings expressed in nanoseconds (if the property is not
> +present 0 is assumed):
> +
> +- atmel,ncs-rd-setup-ns
> +- atmel,nrd-setup-ns
> +- atmel,ncs-wr-setup-ns
> +- atmel,nwe-setup-ns
> +- atmel,ncs-rd-pulse-ns
> +- atmel,nrd-pulse-ns
> +- atmel,ncs-wr-pulse-ns
> +- atmel,nwe-pulse-ns
> +- atmel,nwe-cycle-ns
> +- atmel,nrd-cycle-ns
> +- atmel,tdf-ns
> +
> +- atmel,tdf-optimized          data float optimized mode. If present the data
> +                               float time is optimized depending on the next
> +                               device being accessed (next device setup
> +                               time is substracted to the current devive data
> +                               float time).
> +
> +
> +
> +Example:
> +
> +       ebi: ebi@10000000 {
> +               compatible = "atmel,sama5d3-ebi", "simple-bus";
> +               #address-cells = <2>;
> +               #size-cells = <1>;
> +               atmel,smc = <&hsmc>;
> +               atmel,matrix = <&matrix>;
> +               reg = <0x10000000 0x10000000
> +                      0x40000000 0x30000000>;
> +               ranges = <0x0 0x0 0x10000000 0x10000000
> +                         0x1 0x0 0x40000000 0x10000000
> +                         0x2 0x0 0x50000000 0x10000000
> +                         0x3 0x0 0x60000000 0x10000000>;
> +               clocks = <&mck>;
> +
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&pinctrl_ebi_addr>;
> +
> +               cs@0 {
> +                       #address-cells = <2>;
> +                       #size-cells = <1>;
> +                       ranges;
> +                       atmel,generic-dev;
> +                       atmel,read-mode = "nrd";
> +                       atmel,write-mode = "nwe";
> +                       atmel,bus-width = <16>;
> +                       atmel,ncs-rd-setup-ns = <0>;
> +                       atmel,ncs-wr-setup-ns = <0>;
> +                       atmel,nwe-setup-ns = <8>;
> +                       atmel,nrd-setup-ns = <16>;
> +                       atmel,ncs-rd-pulse-ns = <84>;
> +                       atmel,ncs-wr-pulse-ns = <84>;
> +                       atmel,nrd-pulse-ns = <76>;
> +                       atmel,nwe-pulse-ns = <76>;
> +                       atmel,nrd-cycle-ns = <107>;
> +                       atmel,nwe-cycle-ns = <84>;
> +                       atmel,tdf-ns = <16>;
> +
> +                       nor: flash@0,0 {
> +                               compatible = "cfi-flash";
> +                               #address-cells = <1>;
> +                               #size-cells = <1>;
> +                               reg = <0x0 0x0 0x1000000>;
> +                               bank-width = <2>;
> +                       };
> +               };
> +       };
> +
> --
> 1.9.1
>

Re: [PATCH v2 06/11] memory: atmel-ebi: add DT bindings documentation

[Boris Brezillon]

On Wed, 5 Nov 2014 17:22:57 +0100
Jean-Jacques Hiblot <jjhiblot@traphandler.com> wrote:

> Hi Boris,
> 
> 2014-11-05 17:01 GMT+01:00 Boris Brezillon <boris.brezillon@free-electrons.com>:
> > Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> > ---
> >  .../bindings/memory-controllers/atmel-ebi.txt      | 153 +++++++++++++++++++++
> >  1 file changed, 153 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt
> >
> > diff --git a/Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt b/Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt
> > new file mode 100644
> > index 0000000..dc2c34f
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt
> > @@ -0,0 +1,153 @@
> > +* Device tree bindings for Atmel EBI
> > +
> > +The External Bus Interface (EBI) controller is a bus where you can connect
> > +asynchronous (NAND, NOR, SRAM, ....) and synchronous memories (SDR/DDR SDRAMs).
> > +The EBI provides a glue-less interface to asynchronous memories though the SMC
> > +(Static Memory Controller).
> > +Synchronous memories (and some asynchronous memories like NANDs) can be
> > +attached to specialized controllers which are responsible for configuring the
> > +bus appropriately according to the connected device.
> > +In the other hand, the bus interface can be automated for simple asynchronous
> > +devices.

[...]

> > +
> > +Optional child cs node properties:
> > +- atmel,generic-dev            boolean property specifying if the device is
> > +                               a generic device.
> > +                               The following properties are only parsed if
> > +                               this property is present.
> > +                               Specialized devices are attached to specialized
> > +                               controllers which should configure the bus
> > +                               appropriately.
> 
> What do you mean by specialized devices ? Can you give an example ?

The ones I have in mind are NAND chips: the NAND controller can
automatically discover the required timings and configure the SMC
accordingly. In that case there's no need to specify timings in the DT,
because they will/should be dynalically configured by the NAND
controller driver.

But more generally, the datasheet describe 2 modes for some CS ports:
1) the generic mode, which bind the device to the generic SMC engine
2) the specialized mode which binds it to a specific HW block

This mode can be configured in CCFG_EBICSA, and the specialized mode
supported by each CS depends on each SoC.
For example, for the at91sam9x5:
CS1 => DDR2SDR controller
CS3 => NAND Flash Controller/Logic

-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Re: [PATCH v2 05/11] memory: add Atmel EBI (External Bus Interface) driver

[Jean-Jacques Hiblot]

2014-11-05 17:01 GMT+01:00 Boris Brezillon <boris.brezillon@free-electrons.com>:
> The EBI (External Bus Interface) is used to access external peripherals
> (NOR, SRAM, NAND, and other specific devices like ethernet controllers).
> Each device is assigned a CS line and an address range and can have its
> own configuration (timings, access mode, bus width, ...).
> This driver provides a generic DT binding to configure a device according
> to its requirements.
> For specific device controllers (like the NAND one) the SMC timings
> should be configured by the controller driver through the matrix and
> smc syscon regmaps.
>
> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> ---
>  drivers/memory/Kconfig     |  11 +
>  drivers/memory/Makefile    |   1 +
>  drivers/memory/atmel-ebi.c | 615 +++++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 627 insertions(+)
>  create mode 100644 drivers/memory/atmel-ebi.c
>
> diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
> index 6d91c27..dfe24a2 100644
> --- a/drivers/memory/Kconfig
> +++ b/drivers/memory/Kconfig
> @@ -17,6 +17,17 @@ config ATMEL_SDRAMC
>           Starting with the at91sam9g45, this controller supports SDR, DDR and
>           LP-DDR memories.
>
> +config ATMEL_EBI
> +       bool "Atmel EBI driver"
> +       default y
> +       depends on ARCH_AT91 && OF
> +       select MFD_SYSCON
> +       help
> +         Driver for Atmel EBI controller.
> +         Used to configure the EBI (external bus interface) when the device-
> +         tree is used. This bus supports NANDs, external ethernet controller,
> +         SRAMs, ATA devices, etc.
> +
>  config TI_AEMIF
>         tristate "Texas Instruments AEMIF driver"
>         depends on (ARCH_DAVINCI || ARCH_KEYSTONE) && OF
> diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile
> index c32d319..7ca2c19 100644
> --- a/drivers/memory/Makefile
> +++ b/drivers/memory/Makefile
> @@ -6,6 +6,7 @@ ifeq ($(CONFIG_DDR),y)
>  obj-$(CONFIG_OF)               += of_memory.o
>  endif
>  obj-$(CONFIG_ATMEL_SDRAMC)     += atmel-sdramc.o
> +obj-$(CONFIG_ATMEL_EBI)                += atmel-ebi.o
>  obj-$(CONFIG_TI_AEMIF)         += ti-aemif.o
>  obj-$(CONFIG_TI_EMIF)          += emif.o
>  obj-$(CONFIG_FSL_CORENET_CF)   += fsl-corenet-cf.o
> diff --git a/drivers/memory/atmel-ebi.c b/drivers/memory/atmel-ebi.c
> new file mode 100644
> index 0000000..41bc893
> --- /dev/null
> +++ b/drivers/memory/atmel-ebi.c
> @@ -0,0 +1,615 @@
> +/*
> + * EBI driver for Atmel SAM9 chips
> + * inspired by the fsl weim bus driver
> + *
> + * Copyright (C) 2013 JJ Hiblot.
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/mfd/syscon/atmel-matrix.h>
> +#include <linux/mfd/syscon/atmel-smc.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/regmap.h>
> +
> +#define AT91SAM9_SMC_READ_MODE_MSK     BIT(0)
> +#define AT91SAM9_SMC_READ_NCS_MODE     0
> +#define AT91SAM9_SMC_READ_NRD_MODE     1
> +#define AT91SAM9_SMC_WRITE_MODE_MSK    BIT(1)
> +#define AT91SAM9_SMC_WRITE_NCS_MODE    (0 << 1)
> +#define AT91SAM9_SMC_WRITE_NWE_MODE    (1 << 1)
> +#define AT91SAM9_SMC_EXNW_MODE_MSK     GENMASK(5, 4)
> +#define AT91SAM9_SMC_EXNW_DIS          (0 << 4)
> +#define AT91SAM9_SMC_EXNW_FROZEN       (2 << 4)
> +#define AT91SAM9_SMC_EXNW_READY                (3 << 4)
> +#define AT91SAM9_SMC_BAT_MSK           BIT(8)
> +#define AT91SAM9_SMC_BAT_SELECT                (0 << 8)
> +#define AT91SAM9_SMC_BAT_WRITE         (1 << 8)
> +#define AT91SAM9_SMC_DBW_MSK           GENMASK(13, 12)
> +#define AT91SAM9_SMC_DBW(x)            ((((x) / 16) & 0x3) << 12)
> +#define AT91SAM9_SMC_TDF_CYCLES_MSK    GENMASK(19, 16)
> +#define AT91SAM9_SMC_TDF_CYCLES(x)     (((x) & 0xf) << 16)
> +#define AT91SAM9_SMC_TDF_MODE_MSK      BIT(20)
> +#define AT91SAM9_SMC_TDF_OPTIMIZED     (1 << 20)
> +#define AT91SAM9_SMC_PMEN              BIT(24)
> +#define AT91SAM9_SMC_PS(x)             ((((x) / 4) & 0x3) << 28)

Those definitions are now also available in
linux/mfd/syscon/atmel-smc.h.For consistency sake, this driver should
probably use the new ones.
BTW this patch should probably be applied after patch 3 "mfd: syscon:
Add atmel-smc registers definition" and patch 1 "mfd: syscon: Add
atmel-matrix registers definition"

> +
> +#define AT91_EBICSA_REGFIELD(soc)                      \
> +       REG_FIELD(soc ## _MATRIX_EBICSA_OFF, 0,         \
> +                 AT91_MATRIX_EBI_NUM_CS - 1)
> +
> +#define AT91_MULTI_EBICSA_REGFIELD(soc, n)             \
> +       REG_FIELD(soc ## _MATRIX_EBI ## n ## CSA_OFF,   \
> +                 0, AT91_MATRIX_EBI_NUM_CS - 1)
> +
> +struct at91sam9_smc_timings {
> +       u32 ncs_rd_setup_ns;
> +       u32 nrd_setup_ns;
> +       u32 ncs_wr_setup_ns;
> +       u32 nwe_setup_ns;
> +       u32 ncs_rd_pulse_ns;
> +       u32 nrd_pulse_ns;
> +       u32 ncs_wr_pulse_ns;
> +       u32 nwe_pulse_ns;
> +       u32 nrd_cycle_ns;
> +       u32 nwe_cycle_ns;
> +       u32 tdf_ns;
> +};
> +
> +struct at91sam9_smc_generic_fields {
> +       struct regmap_field *setup;
> +       struct regmap_field *pulse;
> +       struct regmap_field *cycle;
> +       struct regmap_field *mode;
> +};
> +
> +struct at91sam9_ebi_dev_config {
> +       struct at91sam9_smc_timings timings;
> +       u32 mode;
> +};
> +
> +struct at91_ebi;
> +
> +struct at91_ebi_dev {
> +       struct device_node *np;
> +       struct at91_smc_timings *timings;
> +       struct at91_ebi *ebi;
> +       u32 mode;
> +       int cs;
> +       void *config;
> +};
> +
> +struct at91_ebi_caps {
> +       unsigned int available_cs;
> +       const struct reg_field *ebi_csa;
> +       int (*xlate_config)(struct at91_ebi_dev *ebid);
> +       int (*apply_config)(struct at91_ebi_dev *ebid);
> +       int (*init)(struct at91_ebi *ebi);
> +};
> +
> +struct at91_ebi {
> +       struct clk *clk;
> +       struct regmap *smc;
> +       struct regmap *matrix;
> +
> +       struct regmap_field *ebi_csa;
> +
> +       struct device *dev;
> +       const struct at91_ebi_caps *caps;
> +       struct at91_ebi_dev *devs[AT91_MATRIX_EBI_NUM_CS];
> +       void *priv;
> +};
> +
> +static u32 at91sam9_smc_setup_ns_to_cycles(unsigned int clk_rate,
> +                                          u32 timing_ns)
> +{
> +       u32 clk_period = DIV_ROUND_UP(NSEC_PER_SEC, clk_rate);
> +       u32 coded_cycles = 0;
> +       u32 cycles;
> +
> +       cycles = DIV_ROUND_UP(timing_ns, clk_period);
> +       if (cycles / 32) {
> +               coded_cycles |= 1 << 5;
> +               if (cycles < 128)
> +                       cycles = 0;
> +       }
> +
> +       coded_cycles |= cycles % 32;
> +
> +       return coded_cycles;
> +}
> +
> +static u32 at91sam9_smc_pulse_ns_to_cycles(unsigned int clk_rate,
> +                                          u32 timing_ns)
> +{
> +       u32 clk_period = DIV_ROUND_UP(NSEC_PER_SEC, clk_rate);
> +       u32 coded_cycles = 0;
> +       u32 cycles;
> +
> +       cycles = DIV_ROUND_UP(timing_ns, clk_period);
> +       if (cycles / 64) {
> +               coded_cycles |= 1 << 6;
> +               if (cycles < 256)
> +                       cycles = 0;
> +       }
> +
> +       coded_cycles |= cycles % 64;
> +
> +       return coded_cycles;
> +}
> +
> +static u32 at91sam9_smc_cycle_ns_to_cycles(unsigned int clk_rate,
> +                                          u32 timing_ns)
> +{
> +       u32 clk_period = DIV_ROUND_UP(NSEC_PER_SEC, clk_rate);
> +       u32 coded_cycles = 0;
> +       u32 cycles;
> +
> +       cycles = DIV_ROUND_UP(timing_ns, clk_period);
> +       if (cycles / 128) {
> +               coded_cycles = cycles / 256;
> +               cycles %= 256;
> +               if (cycles >= 128) {
> +                       coded_cycles++;
> +                       cycles = 0;
> +               }
> +
> +               if (coded_cycles > 0x3) {
> +                       coded_cycles = 0x3;
> +                       cycles = 0x7f;
> +               }
> +
> +               coded_cycles <<= 7;
> +       }
> +
> +       coded_cycles |= cycles % 128;
> +
> +       return coded_cycles;
> +}
> +
> +static int at91sam9_ebi_apply_config(struct at91_ebi_dev *ebid)
> +{
> +       unsigned int clk_rate = clk_get_rate(ebid->ebi->clk);
> +       struct at91sam9_ebi_dev_config *config = ebid->config;
> +       struct at91sam9_smc_timings *timings = &config->timings;
> +       struct at91sam9_smc_generic_fields *fields = ebid->ebi->priv;
> +       u32 val;
> +
> +       val = at91sam9_smc_setup_ns_to_cycles(clk_rate,
> +                                             timings->ncs_rd_setup_ns) << 24;
> +       val |= at91sam9_smc_setup_ns_to_cycles(clk_rate,
> +                                              timings->nrd_setup_ns) << 16;
> +       val |= at91sam9_smc_setup_ns_to_cycles(clk_rate,
> +                                              timings->ncs_wr_setup_ns) << 8;
> +       val |= at91sam9_smc_setup_ns_to_cycles(clk_rate,
> +                                              timings->nwe_setup_ns);
> +       regmap_fields_write(fields->setup, ebid->cs, val);
> +
> +       val = at91sam9_smc_pulse_ns_to_cycles(clk_rate,
> +                                             timings->ncs_rd_pulse_ns) << 24;
> +       val |= at91sam9_smc_pulse_ns_to_cycles(clk_rate,
> +                                              timings->nrd_pulse_ns) << 16;
> +       val |= at91sam9_smc_pulse_ns_to_cycles(clk_rate,
> +                                              timings->ncs_wr_pulse_ns) << 8;
> +       val |= at91sam9_smc_pulse_ns_to_cycles(clk_rate,
> +                                              timings->nwe_pulse_ns);
> +       regmap_fields_write(fields->pulse, ebid->cs, val);
> +
> +       val = at91sam9_smc_cycle_ns_to_cycles(clk_rate,
> +                                             timings->nrd_cycle_ns) << 16;
> +       val |= at91sam9_smc_cycle_ns_to_cycles(clk_rate,
> +                                              timings->nwe_cycle_ns);
> +       regmap_fields_write(fields->cycle, ebid->cs, val);
> +
> +       val = DIV_ROUND_UP(timings->tdf_ns, clk_rate);
> +       if (val > 16)
> +               val = 16;
> +       regmap_fields_write(fields->mode, ebid->cs, config->mode | val << 16);
> +
> +       return 0;
> +}
> +
> +static int at91sam9_smc_xslate_timings(struct at91_ebi_dev *ebid)
> +{
> +       struct at91sam9_ebi_dev_config *config = ebid->config;
> +       struct at91sam9_smc_timings *timings;
> +       struct device_node *np = ebid->np;
> +
> +       timings = &config->timings;
> +
> +       of_property_read_u32(np, "atmel,ncs-rd-setup-ns",
> +                            &timings->ncs_rd_setup_ns);
> +       of_property_read_u32(np, "atmel,nrd-setup-ns",
> +                            &timings->nrd_setup_ns);
> +       of_property_read_u32(np, "atmel,ncs-wr-setup-ns",
> +                            &timings->ncs_wr_setup_ns);
> +       of_property_read_u32(np, "atmel,nwe-setup-ns",
> +                            &timings->nwe_setup_ns);
> +       of_property_read_u32(np, "atmel,ncs-rd-pulse-ns",
> +                            &timings->ncs_rd_pulse_ns);
> +       of_property_read_u32(np, "atmel,nrd-pulse-ns",
> +                            &timings->nrd_pulse_ns);
> +       of_property_read_u32(np, "atmel,ncs-wr-pulse-ns",
> +                            &timings->ncs_wr_pulse_ns);
> +       of_property_read_u32(np, "atmel,nwe-pulse-ns", &timings->nwe_pulse_ns);
> +       of_property_read_u32(np, "atmel,nwe-cycle-ns", &timings->nwe_cycle_ns);
> +       of_property_read_u32(np, "atmel,nrd-cycle-ns", &timings->nrd_cycle_ns);
> +       of_property_read_u32(np, "atmel,tdf-ns", &timings->tdf_ns);
> +
> +       return 0;
> +}
> +
> +static int at91sam9_ebi_xslate_config(struct at91_ebi_dev *ebid)
> +{
> +       struct at91sam9_ebi_dev_config *config = ebid->config;
> +       struct device_node *np = ebid->np;
> +       const char *tmp_str;
> +       u32 tmp;
> +       int ret;
> +
> +       config = devm_kzalloc(ebid->ebi->dev, sizeof(*config), GFP_KERNEL);
> +       if (!config)
> +               return -ENOMEM;
> +
> +       ebid->config = config;
> +
> +       ret = of_property_read_u32(np, "atmel,bus-width", &tmp);
> +       if (ret)
> +               return ret;
> +
> +       if (tmp != 8 && tmp != 16 && tmp != 32)
> +               return -EINVAL;
> +
> +       config->mode |= AT91SAM9_SMC_DBW(tmp);
> +
> +       if (of_property_read_bool(np, "atmel,tdf-optimized"))
> +               config->mode |= AT91SAM9_SMC_TDF_OPTIMIZED;
> +
> +       tmp_str = NULL;
> +       of_property_read_string(np, "atmel,byte-access-type", &tmp_str);
> +       if (tmp_str && !strcmp(tmp_str, "write"))
> +               config->mode |= AT91SAM9_SMC_BAT_WRITE;
> +
> +       tmp_str = NULL;
> +       of_property_read_string(np, "atmel,read-mode", &tmp_str);
> +       if (tmp_str && !strcmp(tmp_str, "nrd"))
> +               config->mode |= AT91SAM9_SMC_READ_NRD_MODE;
> +
> +       tmp_str = NULL;
> +       of_property_read_string(np, "atmel,write-mode", &tmp_str);
> +       if (tmp_str && !strcmp(tmp_str, "nwe"))
> +               config->mode |= AT91SAM9_SMC_WRITE_NWE_MODE;
> +
> +       tmp_str = NULL;
> +       of_property_read_string(np, "atmel,exnw-mode", &tmp_str);
> +       if (tmp_str) {
> +               if (!strcmp(tmp_str, "frozen"))
> +                       config->mode |= AT91SAM9_SMC_EXNW_FROZEN;
> +               else if (!strcmp(tmp_str, "ready"))
> +                       config->mode |= AT91SAM9_SMC_EXNW_READY;
> +       }
> +
> +       tmp = 0;
> +       of_property_read_u32(np, "atmel,page-mode", &tmp);
> +       if (tmp)
> +               config->mode |= AT91SAM9_SMC_PS(tmp) | AT91SAM9_SMC_PMEN;
> +
> +       return at91sam9_smc_xslate_timings(ebid);
> +}
> +
> +static int at91sam9_ebi_init(struct at91_ebi *ebi)
> +{
> +       struct at91sam9_smc_generic_fields *fields;
> +       struct reg_field field = REG_FIELD(0, 0, 31);
> +
> +       fields = devm_kzalloc(ebi->dev, sizeof(*fields), GFP_KERNEL);
> +       if (!fields)
> +               return -ENOMEM;
> +
> +       field.id_size = fls(ebi->caps->available_cs);
> +       field.id_offset = 0x10;
> +
> +       field.reg = AT91SAM9_SMC_SETUP(AT91SAM9_SMC_GENERIC_OFFSET);
> +       fields->setup = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
> +       if (IS_ERR(fields->setup))
> +               return PTR_ERR(fields->setup);
> +
> +       field.reg = AT91SAM9_SMC_PULSE(AT91SAM9_SMC_GENERIC_OFFSET);
> +       fields->pulse = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
> +       if (IS_ERR(fields->pulse))
> +               return PTR_ERR(fields->pulse);
> +
> +       field.reg = AT91SAM9_SMC_CYCLE(AT91SAM9_SMC_GENERIC_OFFSET);
> +       fields->cycle = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
> +       if (IS_ERR(fields->cycle))
> +               return PTR_ERR(fields->cycle);
> +
> +       field.reg = AT91SAM9_SMC_MODE(AT91SAM9_SMC_GENERIC_OFFSET);
> +       fields->mode = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
> +       if (IS_ERR(fields->mode))
> +               return PTR_ERR(fields->mode);
> +
> +       ebi->priv = fields;
> +
> +       return 0;
> +}
> +
> +static int sama5d3_ebi_init(struct at91_ebi *ebi)
> +{
> +       struct at91sam9_smc_generic_fields *fields;
> +       struct reg_field field = REG_FIELD(0, 0, 31);
> +
> +       fields = devm_kzalloc(ebi->dev, sizeof(*fields), GFP_KERNEL);
> +       if (!fields)
> +               return -ENOMEM;
> +
> +       field.id_size = fls(ebi->caps->available_cs);
> +       field.id_offset = SAMA5_SMC_GENERIC_BLK_SZ;
> +
> +       field.reg = AT91SAM9_SMC_SETUP(SAMA5_SMC_GENERIC_OFFSET);
> +       fields->setup = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
> +       if (IS_ERR(fields->setup))
> +               return PTR_ERR(fields->setup);
> +
> +       field.reg = AT91SAM9_SMC_PULSE(SAMA5_SMC_GENERIC_OFFSET);
> +       fields->pulse = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
> +       if (IS_ERR(fields->pulse))
> +               return PTR_ERR(fields->pulse);
> +
> +       field.reg = AT91SAM9_SMC_CYCLE(SAMA5_SMC_GENERIC_OFFSET);
> +       fields->cycle = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
> +       if (IS_ERR(fields->cycle))
> +               return PTR_ERR(fields->cycle);
> +
> +       field.reg = SAMA5_SMC_MODE(SAMA5_SMC_GENERIC_OFFSET);
> +       fields->mode = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
> +       if (IS_ERR(fields->mode))
> +               return PTR_ERR(fields->mode);
> +
> +       ebi->priv = fields;
> +
> +       return 0;
> +}
> +
> +static int at91_ebi_dev_setup(struct at91_ebi *ebi, struct device_node *np)
> +{
> +       struct device *dev = ebi->dev;
> +       struct device_node *dev_np;
> +       struct at91_ebi_dev *ebid;
> +       u32 tmp;
> +       int ret;
> +
> +       dev_np = of_get_next_child(np, NULL);
> +       if (!dev_np)
> +               return -EINVAL;
> +
> +       if (!of_device_is_available(dev_np))
> +               return 0;
> +
> +       ebid = devm_kzalloc(ebi->dev, sizeof(*ebid), GFP_KERNEL);
> +       if (!ebid)
> +               return -ENOMEM;
> +
> +       ret = of_property_read_u32(dev_np, "reg" , &tmp);
> +       if (ret < 0) {
> +               dev_err(dev, "missing mandatory reg property\n");
> +               return ret;
> +       }
> +
> +       if (tmp > AT91_MATRIX_EBI_NUM_CS ||
> +           !(BIT(tmp) & ebi->caps->available_cs)) {
> +               dev_err(dev, "invalid reg property\n");
> +               return -EINVAL;
> +       }
> +
> +       ebid->cs = tmp;
> +       ebid->np = np;
> +       ebid->ebi = ebi;
> +
> +       if (!of_property_read_bool(np, "atmel,generic-dev"))
> +               goto populate;
> +
> +       if (ebid->ebi->ebi_csa)
> +               regmap_field_update_bits(ebid->ebi->ebi_csa,
> +                                        BIT(ebid->cs),
> +                                        ~BIT(ebid->cs));
> +
> +       ret = ebid->ebi->caps->xlate_config(ebid);
> +       if (ret)
> +               return ret;
> +
> +       ret = ebid->ebi->caps->apply_config(ebid);
> +       if (ret)
> +               return ret;
> +       ebi->devs[ebid->cs] = ebid;
> +
> +populate:
> +       return of_platform_populate(np, of_default_bus_match_table, NULL, dev);
> +}
> +
> +static const struct reg_field at91sam9260_ebi_csa =
> +                               AT91_EBICSA_REGFIELD(AT91SAM9260);
> +
> +static const struct at91_ebi_caps at91sam9260_ebi_caps = {
> +       .available_cs = 0xff,
> +       .ebi_csa = &at91sam9260_ebi_csa,
> +       .xlate_config = at91sam9_ebi_xslate_config,
> +       .apply_config = at91sam9_ebi_apply_config,
> +       .init = at91sam9_ebi_init,
> +};
> +
> +static const struct reg_field at91sam9261_ebi_csa =
> +                               AT91_EBICSA_REGFIELD(AT91SAM9261);
> +
> +static const struct at91_ebi_caps at91sam9261_ebi_caps = {
> +       .available_cs = 0xff,
> +       .ebi_csa = &at91sam9261_ebi_csa,
> +       .xlate_config = at91sam9_ebi_xslate_config,
> +       .apply_config = at91sam9_ebi_apply_config,
> +       .init = at91sam9_ebi_init,
> +};
> +
> +static const struct reg_field at91sam9263_ebi0_csa =
> +                               AT91_MULTI_EBICSA_REGFIELD(AT91SAM9263, 0);
> +
> +static const struct at91_ebi_caps at91sam9263_ebi0_caps = {
> +       .available_cs = 0x3f,
> +       .ebi_csa = &at91sam9263_ebi0_csa,
> +       .xlate_config = at91sam9_ebi_xslate_config,
> +       .apply_config = at91sam9_ebi_apply_config,
> +       .init = at91sam9_ebi_init,
> +};
> +
> +static const struct reg_field at91sam9263_ebi1_csa =
> +                               AT91_MULTI_EBICSA_REGFIELD(AT91SAM9263, 1);
> +
> +static const struct at91_ebi_caps at91sam9263_ebi1_caps = {
> +       .available_cs = 0x7,
> +       .ebi_csa = &at91sam9263_ebi1_csa,
> +       .xlate_config = at91sam9_ebi_xslate_config,
> +       .apply_config = at91sam9_ebi_apply_config,
> +       .init = at91sam9_ebi_init,
> +};
> +
> +static const struct reg_field at91sam9g45_ebi_csa =
> +                               AT91_EBICSA_REGFIELD(AT91SAM9G45);
> +
> +static const struct at91_ebi_caps at91sam9g45_ebi_caps = {
> +       .available_cs = 0x3f,
> +       .ebi_csa = &at91sam9g45_ebi_csa,
> +       .xlate_config = at91sam9_ebi_xslate_config,
> +       .apply_config = at91sam9_ebi_apply_config,
> +       .init = at91sam9_ebi_init,
> +};
> +
> +static const struct at91_ebi_caps at91sam9x5_ebi_caps = {
> +       .available_cs = 0x3f,
> +       .ebi_csa = &at91sam9263_ebi0_csa,
> +       .xlate_config = at91sam9_ebi_xslate_config,
> +       .apply_config = at91sam9_ebi_apply_config,
> +       .init = at91sam9_ebi_init,
> +};
> +
> +static const struct at91_ebi_caps sama5d3_ebi_caps = {
> +       .available_cs = 0xf,
> +       .xlate_config = at91sam9_ebi_xslate_config,
> +       .apply_config = at91sam9_ebi_apply_config,
> +       .init = sama5d3_ebi_init,
> +};
> +
> +static const struct of_device_id at91_ebi_id_table[] = {
> +       {
> +               .compatible = "atmel,at91sam9260-ebi",
> +               .data = &at91sam9260_ebi_caps,
> +       },
> +       {
> +               .compatible = "atmel,at91sam9261-ebi",
> +               .data = &at91sam9261_ebi_caps,
> +       },
> +       {
> +               .compatible = "atmel,at91sam9263-ebi0",
> +               .data = &at91sam9263_ebi0_caps,
> +       },
> +       {
> +               .compatible = "atmel,at91sam9263-ebi1",
> +               .data = &at91sam9263_ebi1_caps,
> +       },
> +       {
> +               .compatible = "atmel,at91sam9g45-ebi",
> +               .data = &at91sam9g45_ebi_caps,
> +       },
> +       {
> +               .compatible = "atmel,at91sam9x5-ebi",
> +               .data = &at91sam9x5_ebi_caps,
> +       },
> +       {
> +               .compatible = "atmel,sama5d3-ebi",
> +               .data = &sama5d3_ebi_caps,
> +       },
> +       { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, at91_ebi_id_table);
> +
> +static int at91_ebi_probe(struct platform_device *pdev)
> +{
> +       const struct of_device_id *match;
> +       struct device_node *child;
> +       struct device_node *np;
> +       struct at91_ebi *ebi;
> +       struct clk *clk;
> +       int ret;
> +
> +       match = of_match_device(at91_ebi_id_table, &pdev->dev);
> +       if (!match || !match->data)
> +               return -EINVAL;
> +
> +       ebi = devm_kzalloc(&pdev->dev, sizeof(*ebi), GFP_KERNEL);
> +       if (!ebi)
> +               return -ENOMEM;
> +
> +       ebi->caps = match->data;
> +       ebi->dev = &pdev->dev;
> +
> +       clk = devm_clk_get(&pdev->dev, NULL);
> +       if (IS_ERR(clk))
> +               return PTR_ERR(clk);
> +
> +       ebi->clk = clk;
> +
> +       np = of_parse_phandle(pdev->dev.of_node, "atmel,smc", 0);
> +       if (!np)
> +               return -EINVAL;
> +
> +       ebi->smc = syscon_node_to_regmap(np);
> +       if (IS_ERR(ebi->smc))
> +               return PTR_ERR(ebi->smc);
> +
> +       /*
> +        * The sama5d3 does not provide an EBICSA register and thus does need
> +        * to access the matrix registers.
> +        */
> +       if (ebi->caps->ebi_csa) {
> +               np = of_parse_phandle(pdev->dev.of_node, "atmel,matrix", 0);
> +               if (np)
> +                       return -EINVAL;
> +
> +               ebi->matrix = syscon_node_to_regmap(np);
> +               if (IS_ERR(ebi->matrix))
> +                       return PTR_ERR(ebi->matrix);
> +
> +               ebi->ebi_csa = regmap_field_alloc(ebi->matrix,
> +                                                 *ebi->caps->ebi_csa);
> +               if (IS_ERR(ebi->ebi_csa))
> +                       return PTR_ERR(ebi->ebi_csa);
> +       }
> +
> +       ret = ebi->caps->init(ebi);
> +       if (ret)
> +               return ret;
> +
> +       for_each_child_of_node(pdev->dev.of_node, child) {
> +               ret = at91_ebi_dev_setup(ebi, child);
> +               if (ret)
> +                       return ret;
> +       }
> +
> +       return ret;
> +}
> +
> +static struct platform_driver at91_ebi_driver = {
> +       .driver = {
> +               .name = "atmel-ebi",
> +               .of_match_table = at91_ebi_id_table,
> +       },
> +};
> +module_platform_driver_probe(at91_ebi_driver, at91_ebi_probe);
> +
> +MODULE_AUTHOR("JJ Hiblot");
> +MODULE_DESCRIPTION("Atmel's EBI driver");
> +MODULE_LICENSE("GPL");
> --
> 1.9.1
>

Re: [PATCH v2 05/11] memory: add Atmel EBI (External Bus Interface) driver

[Boris Brezillon]

On Wed, 5 Nov 2014 17:53:42 +0100
Jean-Jacques Hiblot <jjhiblot@traphandler.com> wrote:

> 2014-11-05 17:01 GMT+01:00 Boris Brezillon <boris.brezillon@free-electrons.com>:
> > The EBI (External Bus Interface) is used to access external peripherals
> > (NOR, SRAM, NAND, and other specific devices like ethernet controllers).
> > Each device is assigned a CS line and an address range and can have its
> > own configuration (timings, access mode, bus width, ...).
> > This driver provides a generic DT binding to configure a device according
> > to its requirements.
> > For specific device controllers (like the NAND one) the SMC timings
> > should be configured by the controller driver through the matrix and
> > smc syscon regmaps.
> >
> > Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
> > Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> > ---
> >  drivers/memory/Kconfig     |  11 +
> >  drivers/memory/Makefile    |   1 +
> >  drivers/memory/atmel-ebi.c | 615 +++++++++++++++++++++++++++++++++++++++++++++
> >  3 files changed, 627 insertions(+)
> >  create mode 100644 drivers/memory/atmel-ebi.c
> >
> > diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
> > index 6d91c27..dfe24a2 100644
> > --- a/drivers/memory/Kconfig
> > +++ b/drivers/memory/Kconfig
> > @@ -17,6 +17,17 @@ config ATMEL_SDRAMC
> >           Starting with the at91sam9g45, this controller supports SDR, DDR and
> >           LP-DDR memories.
> >
> > +config ATMEL_EBI
> > +       bool "Atmel EBI driver"
> > +       default y
> > +       depends on ARCH_AT91 && OF
> > +       select MFD_SYSCON
> > +       help
> > +         Driver for Atmel EBI controller.
> > +         Used to configure the EBI (external bus interface) when the device-
> > +         tree is used. This bus supports NANDs, external ethernet controller,
> > +         SRAMs, ATA devices, etc.
> > +
> >  config TI_AEMIF
> >         tristate "Texas Instruments AEMIF driver"
> >         depends on (ARCH_DAVINCI || ARCH_KEYSTONE) && OF
> > diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile
> > index c32d319..7ca2c19 100644
> > --- a/drivers/memory/Makefile
> > +++ b/drivers/memory/Makefile
> > @@ -6,6 +6,7 @@ ifeq ($(CONFIG_DDR),y)
> >  obj-$(CONFIG_OF)               += of_memory.o
> >  endif
> >  obj-$(CONFIG_ATMEL_SDRAMC)     += atmel-sdramc.o
> > +obj-$(CONFIG_ATMEL_EBI)                += atmel-ebi.o
> >  obj-$(CONFIG_TI_AEMIF)         += ti-aemif.o
> >  obj-$(CONFIG_TI_EMIF)          += emif.o
> >  obj-$(CONFIG_FSL_CORENET_CF)   += fsl-corenet-cf.o
> > diff --git a/drivers/memory/atmel-ebi.c b/drivers/memory/atmel-ebi.c
> > new file mode 100644
> > index 0000000..41bc893
> > --- /dev/null
> > +++ b/drivers/memory/atmel-ebi.c
> > @@ -0,0 +1,615 @@
> > +/*
> > + * EBI driver for Atmel SAM9 chips
> > + * inspired by the fsl weim bus driver
> > + *
> > + * Copyright (C) 2013 JJ Hiblot.
> > + *
> > + * This file is licensed under the terms of the GNU General Public
> > + * License version 2. This program is licensed "as is" without any
> > + * warranty of any kind, whether express or implied.
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/io.h>
> > +#include <linux/mfd/syscon.h>
> > +#include <linux/mfd/syscon/atmel-matrix.h>
> > +#include <linux/mfd/syscon/atmel-smc.h>
> > +#include <linux/module.h>
> > +#include <linux/of_device.h>
> > +#include <linux/regmap.h>
> > +
> > +#define AT91SAM9_SMC_READ_MODE_MSK     BIT(0)
> > +#define AT91SAM9_SMC_READ_NCS_MODE     0
> > +#define AT91SAM9_SMC_READ_NRD_MODE     1
> > +#define AT91SAM9_SMC_WRITE_MODE_MSK    BIT(1)
> > +#define AT91SAM9_SMC_WRITE_NCS_MODE    (0 << 1)
> > +#define AT91SAM9_SMC_WRITE_NWE_MODE    (1 << 1)
> > +#define AT91SAM9_SMC_EXNW_MODE_MSK     GENMASK(5, 4)
> > +#define AT91SAM9_SMC_EXNW_DIS          (0 << 4)
> > +#define AT91SAM9_SMC_EXNW_FROZEN       (2 << 4)
> > +#define AT91SAM9_SMC_EXNW_READY                (3 << 4)
> > +#define AT91SAM9_SMC_BAT_MSK           BIT(8)
> > +#define AT91SAM9_SMC_BAT_SELECT                (0 << 8)
> > +#define AT91SAM9_SMC_BAT_WRITE         (1 << 8)
> > +#define AT91SAM9_SMC_DBW_MSK           GENMASK(13, 12)
> > +#define AT91SAM9_SMC_DBW(x)            ((((x) / 16) & 0x3) << 12)
> > +#define AT91SAM9_SMC_TDF_CYCLES_MSK    GENMASK(19, 16)
> > +#define AT91SAM9_SMC_TDF_CYCLES(x)     (((x) & 0xf) << 16)
> > +#define AT91SAM9_SMC_TDF_MODE_MSK      BIT(20)
> > +#define AT91SAM9_SMC_TDF_OPTIMIZED     (1 << 20)
> > +#define AT91SAM9_SMC_PMEN              BIT(24)
> > +#define AT91SAM9_SMC_PS(x)             ((((x) / 4) & 0x3) << 28)
> 
> Those definitions are now also available in
> linux/mfd/syscon/atmel-smc.h.For consistency sake, this driver should
> probably use the new ones.

That was my intention, I just forgot to cleanup this part...

> BTW this patch should probably be applied after patch 3 "mfd: syscon:
> Add atmel-smc registers definition" and patch 1 "mfd: syscon: Add
> atmel-matrix registers definition"
> 

And it is: patch 05/11 :-)

-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Re: [PATCH v2 05/11] memory: add Atmel EBI (External Bus Interface) driver

[Jean-Jacques Hiblot]

2014-11-05 17:59 GMT+01:00 Boris Brezillon <boris.brezillon@free-electrons.com>:
> On Wed, 5 Nov 2014 17:53:42 +0100
> Jean-Jacques Hiblot <jjhiblot@traphandler.com> wrote:
>
>> 2014-11-05 17:01 GMT+01:00 Boris Brezillon <boris.brezillon@free-electrons.com>:
>> > The EBI (External Bus Interface) is used to access external peripherals
>> > (NOR, SRAM, NAND, and other specific devices like ethernet controllers).
>> > Each device is assigned a CS line and an address range and can have its
>> > own configuration (timings, access mode, bus width, ...).
>> > This driver provides a generic DT binding to configure a device according
>> > to its requirements.
>> > For specific device controllers (like the NAND one) the SMC timings
>> > should be configured by the controller driver through the matrix and
>> > smc syscon regmaps.
>> >
>> > Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
>> > Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
>> > ---
>> >  drivers/memory/Kconfig     |  11 +
>> >  drivers/memory/Makefile    |   1 +
>> >  drivers/memory/atmel-ebi.c | 615 +++++++++++++++++++++++++++++++++++++++++++++
>> >  3 files changed, 627 insertions(+)
>> >  create mode 100644 drivers/memory/atmel-ebi.c
>> >
>> > diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
>> > index 6d91c27..dfe24a2 100644
>> > --- a/drivers/memory/Kconfig
>> > +++ b/drivers/memory/Kconfig
>> > @@ -17,6 +17,17 @@ config ATMEL_SDRAMC
>> >           Starting with the at91sam9g45, this controller supports SDR, DDR and
>> >           LP-DDR memories.
>> >
>> > +config ATMEL_EBI
>> > +       bool "Atmel EBI driver"
>> > +       default y
>> > +       depends on ARCH_AT91 && OF
>> > +       select MFD_SYSCON
>> > +       help
>> > +         Driver for Atmel EBI controller.
>> > +         Used to configure the EBI (external bus interface) when the device-
>> > +         tree is used. This bus supports NANDs, external ethernet controller,
>> > +         SRAMs, ATA devices, etc.
>> > +
>> >  config TI_AEMIF
>> >         tristate "Texas Instruments AEMIF driver"
>> >         depends on (ARCH_DAVINCI || ARCH_KEYSTONE) && OF
>> > diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile
>> > index c32d319..7ca2c19 100644
>> > --- a/drivers/memory/Makefile
>> > +++ b/drivers/memory/Makefile
>> > @@ -6,6 +6,7 @@ ifeq ($(CONFIG_DDR),y)
>> >  obj-$(CONFIG_OF)               += of_memory.o
>> >  endif
>> >  obj-$(CONFIG_ATMEL_SDRAMC)     += atmel-sdramc.o
>> > +obj-$(CONFIG_ATMEL_EBI)                += atmel-ebi.o
>> >  obj-$(CONFIG_TI_AEMIF)         += ti-aemif.o
>> >  obj-$(CONFIG_TI_EMIF)          += emif.o
>> >  obj-$(CONFIG_FSL_CORENET_CF)   += fsl-corenet-cf.o
>> > diff --git a/drivers/memory/atmel-ebi.c b/drivers/memory/atmel-ebi.c
>> > new file mode 100644
>> > index 0000000..41bc893
>> > --- /dev/null
>> > +++ b/drivers/memory/atmel-ebi.c
>> > @@ -0,0 +1,615 @@
>> > +/*
>> > + * EBI driver for Atmel SAM9 chips
>> > + * inspired by the fsl weim bus driver
>> > + *
>> > + * Copyright (C) 2013 JJ Hiblot.
>> > + *
>> > + * This file is licensed under the terms of the GNU General Public
>> > + * License version 2. This program is licensed "as is" without any
>> > + * warranty of any kind, whether express or implied.
>> > + */
>> > +
>> > +#include <linux/clk.h>
>> > +#include <linux/io.h>
>> > +#include <linux/mfd/syscon.h>
>> > +#include <linux/mfd/syscon/atmel-matrix.h>
>> > +#include <linux/mfd/syscon/atmel-smc.h>
>> > +#include <linux/module.h>
>> > +#include <linux/of_device.h>
>> > +#include <linux/regmap.h>
>> > +
>> > +#define AT91SAM9_SMC_READ_MODE_MSK     BIT(0)
>> > +#define AT91SAM9_SMC_READ_NCS_MODE     0
>> > +#define AT91SAM9_SMC_READ_NRD_MODE     1
>> > +#define AT91SAM9_SMC_WRITE_MODE_MSK    BIT(1)
>> > +#define AT91SAM9_SMC_WRITE_NCS_MODE    (0 << 1)
>> > +#define AT91SAM9_SMC_WRITE_NWE_MODE    (1 << 1)
>> > +#define AT91SAM9_SMC_EXNW_MODE_MSK     GENMASK(5, 4)
>> > +#define AT91SAM9_SMC_EXNW_DIS          (0 << 4)
>> > +#define AT91SAM9_SMC_EXNW_FROZEN       (2 << 4)
>> > +#define AT91SAM9_SMC_EXNW_READY                (3 << 4)
>> > +#define AT91SAM9_SMC_BAT_MSK           BIT(8)
>> > +#define AT91SAM9_SMC_BAT_SELECT                (0 << 8)
>> > +#define AT91SAM9_SMC_BAT_WRITE         (1 << 8)
>> > +#define AT91SAM9_SMC_DBW_MSK           GENMASK(13, 12)
>> > +#define AT91SAM9_SMC_DBW(x)            ((((x) / 16) & 0x3) << 12)
>> > +#define AT91SAM9_SMC_TDF_CYCLES_MSK    GENMASK(19, 16)
>> > +#define AT91SAM9_SMC_TDF_CYCLES(x)     (((x) & 0xf) << 16)
>> > +#define AT91SAM9_SMC_TDF_MODE_MSK      BIT(20)
>> > +#define AT91SAM9_SMC_TDF_OPTIMIZED     (1 << 20)
>> > +#define AT91SAM9_SMC_PMEN              BIT(24)
>> > +#define AT91SAM9_SMC_PS(x)             ((((x) / 4) & 0x3) << 28)
>>
>> Those definitions are now also available in
>> linux/mfd/syscon/atmel-smc.h.For consistency sake, this driver should
>> probably use the new ones.
>
> That was my intention, I just forgot to cleanup this part...
>
>> BTW this patch should probably be applied after patch 3 "mfd: syscon:
>> Add atmel-smc registers definition" and patch 1 "mfd: syscon: Add
>> atmel-matrix registers definition"
>>
>
> And it is: patch 05/11 :-)

Damn gmail again for showing it under [Patch 00/11] ! It's definitely
not the ideal review tool :-)
>
> --
> Boris Brezillon, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com

Re: [PATCH v2 00/11] memory: add Atmel EBI (External Bus Interface) driver

[Alexandre Belloni]

On 05/11/2014 at 17:01:16 +0100, Boris Brezillon wrote :
> Arnd, you've commented the first version of this driver (IIRC, you
> focused on the DT binding part), could you give your feedback on this
> version (I based the new DT binding on TI's aemif driver).
> 

Shouldn't you Cc Arnd then? ;)


-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Re: [PATCH v2 01/11] mfd: syscon: Add atmel-matrix registers definition

[Alexandre Belloni]

On 05/11/2014 at 17:01:17 +0100, Boris Brezillon wrote :
> AT91 SoCs have a memory range reserved for internal bus configuration.
> Expose those registers so that drivers can make use of the matrix syscon
> declared in at91 DTs.
> 
> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> ---
>  include/linux/mfd/syscon/atmel-matrix.h | 114 ++++++++++++++++++++++++++++++++

I think we should stop cluttering the include/linux directory and start
doing what has been done for tegra and create an include/soc/atmel or
include/soc/at91 directory. that's what I was planning to do in my
sdramc/reset series but I didn't get any comment on it.

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Re: [PATCH v2 06/11] memory: atmel-ebi: add DT bindings documentation

[Alexandre Belloni]

We probabyl should start making sure we have a commit log for every
patches ;)

On 05/11/2014 at 17:01:22 +0100, Boris Brezillon wrote :
> +Child chip-select (cs) nodes contain the memory devices nodes connected to
> +such as NOR (e.g. cfi-flash) and NAND.
> +There might be board specific devices like FPGAs.
> +You'll define you device requirements in these child nodes.
                 your


-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Re: [PATCH v2 01/11] mfd: syscon: Add atmel-matrix registers definition

[Boris Brezillon]

Hi Alexandre,

On Fri, 7 Nov 2014 14:45:10 +0100
Alexandre Belloni <alexandre.belloni@free-electrons.com> wrote:

> On 05/11/2014 at 17:01:17 +0100, Boris Brezillon wrote :
> > AT91 SoCs have a memory range reserved for internal bus configuration.
> > Expose those registers so that drivers can make use of the matrix syscon
> > declared in at91 DTs.
> > 
> > Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> > ---
> >  include/linux/mfd/syscon/atmel-matrix.h | 114 ++++++++++++++++++++++++++++++++
> 
> I think we should stop cluttering the include/linux directory and start
> doing what has been done for tegra and create an include/soc/atmel or
> include/soc/at91 directory. that's what I was planning to do in my
> sdramc/reset series but I didn't get any comment on it.
> 

I'll let MFD and ARM maintainers decide, but other syscon drivers are
using this directory to define their registers...

Regards,

Boris
-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Re: [PATCH v2 00/11] memory: add Atmel EBI (External Bus Interface) driver

[Boris Brezillon]

On Fri, 7 Nov 2014 14:41:12 +0100
Alexandre Belloni <alexandre.belloni@free-electrons.com> wrote:

> On 05/11/2014 at 17:01:16 +0100, Boris Brezillon wrote :
> > Arnd, you've commented the first version of this driver (IIRC, you
> > focused on the DT binding part), could you give your feedback on this
> > version (I based the new DT binding on TI's aemif driver).
> > 
> 
> Shouldn't you Cc Arnd then? ;)

I bounced the series a few minutes after realizing I had forgotten to
add him in Cc ;-)



-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Re: [PATCH v2 06/11] memory: atmel-ebi: add DT bindings documentation

[Rob Herring]

On Wed, Nov 5, 2014 at 10:01 AM, Boris Brezillon
<boris.brezillon@free-electrons.com> wrote:
> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Perhaps some commit msg?

While this binding seems mostly okay to me, this is the 2nd memory
controller binding I've looked at in the last day [1]. There are
probably some others already as well. This makes me think we need a
generic binding here. At least the node structure and how we define
chip selects should be common.

While I like timing information in time units over magic register
values in the Tegra binding, the reality is converting timing info to
register values is generally very hard to get both correct and
optimal. In the end, you probably need to hand tweak the register
settings anyway. So I'm hesitant to say it must be done 1 way here.

Rob

[1] http://lwn.net/Articles/618466/

> ---
>  .../bindings/memory-controllers/atmel-ebi.txt      | 153 +++++++++++++++++++++
>  1 file changed, 153 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt
>
> diff --git a/Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt b/Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt
> new file mode 100644
> index 0000000..dc2c34f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/memory-controllers/atmel-ebi.txt
> @@ -0,0 +1,153 @@
> +* Device tree bindings for Atmel EBI
> +
> +The External Bus Interface (EBI) controller is a bus where you can connect
> +asynchronous (NAND, NOR, SRAM, ....) and synchronous memories (SDR/DDR SDRAMs).
> +The EBI provides a glue-less interface to asynchronous memories though the SMC
> +(Static Memory Controller).
> +Synchronous memories (and some asynchronous memories like NANDs) can be
> +attached to specialized controllers which are responsible for configuring the
> +bus appropriately according to the connected device.
> +In the other hand, the bus interface can be automated for simple asynchronous
> +devices.
> +
> +Required properties:
> +
> +- compatible:          "atmel,at91sam9260-ebi"
> +                       "atmel,at91sam9261-ebi"
> +                       "atmel,at91sam9263-ebi0"
> +                       "atmel,at91sam9263-ebi1"
> +                       "atmel,at91sam9g45-ebi"
> +                       "atmel,at91sam9x5-ebi"
> +                       "atmel,sama5d3-ebi"
> +
> +- reg:                 Contains offset/length value for EBI memory mapping.
> +                       This property might contain several entries if the EBI
> +                       memory range is not contiguous
> +
> +- #address-cells:      Must be 2.
> +                       The first cell encodes the CS.
> +                       The second cell encode the offset into the CS memory
> +                       range.
> +
> +- #size-cells:         Must be set to 1.
> +
> +- ranges:              Encodes CS to memory region association.
> +
> +- clocks:              Clock feeding the EBI controller.
> +                       See clock-bindings.txt
> +
> +Child chip-select (cs) nodes contain the memory devices nodes connected to
> +such as NOR (e.g. cfi-flash) and NAND.
> +There might be board specific devices like FPGAs.
> +You'll define you device requirements in these child nodes.
> +
> +Required child cs node properties:
> +
> +- #address-cells:      Must be 2.
> +
> +- #size-cells:         Must be 1.
> +
> +- ranges:              Empty property indicating that child nodes can inherit
> +                       memory layout.
> +
> +Optional child cs node properties:
> +- atmel,generic-dev            boolean property specifying if the device is
> +                               a generic device.
> +                               The following properties are only parsed if
> +                               this property is present.
> +                               Specialized devices are attached to specialized
> +                               controllers which should configure the bus
> +                               appropriately.
> +
> +- atmel,bus-width:             width of the asynchronous device's data bus
> +                               8, 16 or 32.
> +                               8 if not present.
> +
> +- atmel,byte-access-type       "write" or "select" (see Atmel datasheet).
> +                               "select" if not present.
> +
> +- atmel,read-mode              "nrd" or "ncs".
> +                               "ncs" is not present.
> +
> +- atmel,write-mode             "nwe" or "ncs".
> +                               "ncs" is not present.
> +
> +- atmel,exnw-mode              "disabled", "frozen" or "ready".
> +                               "disabled" if not present.
> +
> +- atmel,page-mode              enable page mode if present. The provided value
> +                               defines the page size (supported values: 4, 8,
> +                               16 and 32).
> +
> +Optional device timings expressed in nanoseconds (if the property is not
> +present 0 is assumed):
> +
> +- atmel,ncs-rd-setup-ns
> +- atmel,nrd-setup-ns
> +- atmel,ncs-wr-setup-ns
> +- atmel,nwe-setup-ns
> +- atmel,ncs-rd-pulse-ns
> +- atmel,nrd-pulse-ns
> +- atmel,ncs-wr-pulse-ns
> +- atmel,nwe-pulse-ns
> +- atmel,nwe-cycle-ns
> +- atmel,nrd-cycle-ns
> +- atmel,tdf-ns
> +
> +- atmel,tdf-optimized          data float optimized mode. If present the data
> +                               float time is optimized depending on the next
> +                               device being accessed (next device setup
> +                               time is substracted to the current devive data
> +                               float time).
> +
> +
> +
> +Example:
> +
> +       ebi: ebi@10000000 {
> +               compatible = "atmel,sama5d3-ebi", "simple-bus";
> +               #address-cells = <2>;
> +               #size-cells = <1>;
> +               atmel,smc = <&hsmc>;
> +               atmel,matrix = <&matrix>;
> +               reg = <0x10000000 0x10000000
> +                      0x40000000 0x30000000>;
> +               ranges = <0x0 0x0 0x10000000 0x10000000
> +                         0x1 0x0 0x40000000 0x10000000
> +                         0x2 0x0 0x50000000 0x10000000
> +                         0x3 0x0 0x60000000 0x10000000>;
> +               clocks = <&mck>;
> +
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&pinctrl_ebi_addr>;
> +
> +               cs@0 {
> +                       #address-cells = <2>;
> +                       #size-cells = <1>;
> +                       ranges;
> +                       atmel,generic-dev;
> +                       atmel,read-mode = "nrd";
> +                       atmel,write-mode = "nwe";
> +                       atmel,bus-width = <16>;
> +                       atmel,ncs-rd-setup-ns = <0>;
> +                       atmel,ncs-wr-setup-ns = <0>;
> +                       atmel,nwe-setup-ns = <8>;
> +                       atmel,nrd-setup-ns = <16>;
> +                       atmel,ncs-rd-pulse-ns = <84>;
> +                       atmel,ncs-wr-pulse-ns = <84>;
> +                       atmel,nrd-pulse-ns = <76>;
> +                       atmel,nwe-pulse-ns = <76>;
> +                       atmel,nrd-cycle-ns = <107>;
> +                       atmel,nwe-cycle-ns = <84>;
> +                       atmel,tdf-ns = <16>;
> +
> +                       nor: flash@0,0 {
> +                               compatible = "cfi-flash";
> +                               #address-cells = <1>;
> +                               #size-cells = <1>;
> +                               reg = <0x0 0x0 0x1000000>;
> +                               bank-width = <2>;
> +                       };
> +               };
> +       };
> +
> --
> 1.9.1
>

Re: [PATCH v2 06/11] memory: atmel-ebi: add DT bindings documentation

[Boris Brezillon]

On Fri, 7 Nov 2014 09:21:39 -0600
Rob Herring <robherring2@gmail.com> wrote:

> On Wed, Nov 5, 2014 at 10:01 AM, Boris Brezillon
> <boris.brezillon@free-electrons.com> wrote:
> > Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> 
> Perhaps some commit msg?

Yes, I was just lazy and though this series would make another round
anyway :-).

I'll add a commit log to all my commits...

> 
> While this binding seems mostly okay to me, this is the 2nd memory
> controller binding I've looked at in the last day [1]. There are
> probably some others already as well. This makes me think we need a
> generic binding here. At least the node structure and how we define
> chip selects should be common.

Sure.
Any suggestion ?

BTW, I don't use any specific property to define the chip select
associated to a device, because it's already encoded in the reg
property.
TI AEMIF binding define an ti,cs-chipselect property, is there any
reason for doing that ?

Moreover, IMHO it would even make sense to have some sort of
framework/helper functions for those kind of interfaces to external
memories, but this is another story :-).

> 
> While I like timing information in time units over magic register
> values in the Tegra binding, the reality is converting timing info to
> register values is generally very hard to get both correct and
> optimal. In the end, you probably need to hand tweak the register
> settings anyway. So I'm hesitant to say it must be done 1 way here.

Well, I'm not a big fan of timings expressed in clock cycles, cause
this implies changing your DT when you tweak your master/bus clk.
Expressing those timings in nano or pico seconds let the driver figure
out what's the best value according to the current source clk rate.

Regards,

Boris


-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Re: [PATCH v2 06/11] memory: atmel-ebi: add DT bindings documentation

[Tomeu Vizoso]

On 7 November 2014 16:49, Boris Brezillon
<boris.brezillon@free-electrons.com> wrote:
> On Fri, 7 Nov 2014 09:21:39 -0600
> Rob Herring <robherring2@gmail.com> wrote:
>
>> On Wed, Nov 5, 2014 at 10:01 AM, Boris Brezillon
>> <boris.brezillon@free-electrons.com> wrote:
>> > Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
>>
>> Perhaps some commit msg?
>
> Yes, I was just lazy and though this series would make another round
> anyway :-).
>
> I'll add a commit log to all my commits...
>
>>
>> While this binding seems mostly okay to me, this is the 2nd memory
>> controller binding I've looked at in the last day [1]. There are
>> probably some others already as well. This makes me think we need a
>> generic binding here. At least the node structure and how we define
>> chip selects should be common.
>
> Sure.
> Any suggestion ?

I unfortunately cannot see much benefit to a generic binding, but
maybe that's because the one in T124 is a bit special? I'm very
interested in hearing proposals though.

Thanks,

Tomeu

Re: [PATCH v2 01/11] mfd: syscon: Add atmel-matrix registers definition

[Lee Jones]

On Wed, 05 Nov 2014, Boris Brezillon wrote:

> AT91 SoCs have a memory range reserved for internal bus configuration.
> Expose those registers so that drivers can make use of the matrix syscon
> declared in at91 DTs.
> 
> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> ---
>  include/linux/mfd/syscon/atmel-matrix.h | 114 ++++++++++++++++++++++++++++++++
>  1 file changed, 114 insertions(+)
>  create mode 100644 include/linux/mfd/syscon/atmel-matrix.h
> 
> diff --git a/include/linux/mfd/syscon/atmel-matrix.h b/include/linux/mfd/syscon/atmel-matrix.h
> new file mode 100644
> index 0000000..c3faa18
> --- /dev/null
> +++ b/include/linux/mfd/syscon/atmel-matrix.h
> @@ -0,0 +1,114 @@
> +/*
> + *  Copyright (C) 2007 Atmel Corporation.

You need to update this.

Assuming this gets fixed and all of the misalignments are patchisums
i.e. everything is in fact nice lined up in the source file:

Acked-by: Lee Jones <lee.jones@linaro.org>

> + * Memory Controllers (MATRIX, EBI) - System peripherals registers.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + */
> +
> +#ifndef _LINUX_MFD_SYSCON_ATMEL_MATRIX_H
> +#define _LINUX_MFD_SYSCON_ATMEL_MATRIX_H
> +
> +#define AT91SAM9260_MATRIX_MCFG_OFF	0x00
> +#define AT91SAM9260_MATRIX_SCFG_OFF	0x40
> +#define AT91SAM9260_MATRIX_PRS_OFF	0x80
> +#define AT91SAM9260_MATRIX_MRCR_OFF	0x100
> +#define AT91SAM9260_MATRIX_EBICSA_OFF	0x11c
> +
> +#define AT91SAM9261_MATRIX_MRCR_OFF	0x0
> +#define AT91SAM9261_MATRIX_SCFG_OFF	0x4
> +#define AT91SAM9261_MATRIX_TCR_OFF	0x24
> +#define AT91SAM9261_MATRIX_EBICSA_OFF	0x30
> +#define AT91SAM9261_MATRIX_USBPUCR_OFF	0x34
> +
> +#define AT91SAM9263_MATRIX_MCFG_OFF	0x00
> +#define AT91SAM9263_MATRIX_SCFG_OFF	0x40
> +#define AT91SAM9263_MATRIX_PRS_OFF	0x80
> +#define AT91SAM9263_MATRIX_MRCR_OFF	0x100
> +#define AT91SAM9263_MATRIX_TCR_OFF	0x114
> +#define AT91SAM9263_MATRIX_EBI0CSA_OFF	0x120
> +#define AT91SAM9263_MATRIX_EBI1CSA_OFF	0x124
> +
> +#define AT91SAM9G45_MATRIX_MCFG_OFF	0x00
> +#define AT91SAM9G45_MATRIX_SCFG_OFF	0x40
> +#define AT91SAM9G45_MATRIX_PRS_OFF	0x80
> +#define AT91SAM9G45_MATRIX_MRCR_OFF	0x100
> +#define AT91SAM9G45_MATRIX_TCR_OFF	0x110
> +#define AT91SAM9G45_MATRIX_DDRMPR_OFF	0x118
> +#define AT91SAM9G45_MATRIX_EBICSA_OFF	0x128
> +
> +#define AT91SAM9N12_MATRIX_MCFG_OFF	0x00
> +#define AT91SAM9N12_MATRIX_SCFG_OFF	0x40
> +#define AT91SAM9N12_MATRIX_PRS_OFF	0x80
> +#define AT91SAM9N12_MATRIX_MRCR_OFF	0x100
> +#define AT91SAM9N12_MATRIX_EBICSA_OFF	0x118
> +
> +#define AT91SAM9X5_MATRIX_MCFG_OFF	0x00
> +#define AT91SAM9X5_MATRIX_SCFG_OFF	0x40
> +#define AT91SAM9X5_MATRIX_PRS_OFF	0x80
> +#define AT91SAM9X5_MATRIX_MRCR_OFF	0x100
> +#define AT91SAM9X5_MATRIX_EBICSA_OFF	0x120
> +
> +#define SAMA5D3_MATRIX_MCFG_OFF		0x00
> +#define SAMA5D3_MATRIX_SCFG_OFF		0x40
> +#define SAMA5D3_MATRIX_PRS_OFF		0x80
> +#define SAMA5D3_MATRIX_MRCR_OFF		0x100
> +
> +#define AT91_MATRIX_MCFG(o, x)		((o) + ((x) * 0x4))
> +#define AT91_MATRIX_ULBT		(7 << 0)
> +#define AT91_MATRIX_ULBT_INFINITE	(0 << 0)
> +#define AT91_MATRIX_ULBT_SINGLE		(1 << 0)
> +#define AT91_MATRIX_ULBT_FOUR		(2 << 0)
> +#define AT91_MATRIX_ULBT_EIGHT		(3 << 0)
> +#define AT91_MATRIX_ULBT_SIXTEEN	(4 << 0)
> +
> +#define AT91_MATRIX_SCFG(o, x)		((o) + ((x) * 0x4))
> +#define AT91_MATRIX_SLOT_CYCLE		(0xff <<  0)
> +#define AT91_MATRIX_DEFMSTR_TYPE	(3 << 16)
> +#define AT91_MATRIX_DEFMSTR_TYPE_NONE	(0 << 16)
> +#define AT91_MATRIX_DEFMSTR_TYPE_LAST	(1 << 16)
> +#define AT91_MATRIX_DEFMSTR_TYPE_FIXED	(2 << 16)
> +#define AT91_MATRIX_FIXED_DEFMSTR	(7 << 18)
> +#define AT91_MATRIX_ARBT		(3 << 24)
> +#define AT91_MATRIX_ARBT_ROUND_ROBIN	(0 << 24)
> +#define AT91_MATRIX_ARBT_FIXED_PRIORITY	(1 << 24)
> +
> +#define AT91_MATRIX_TCR(o)		(o)
> +#define AT91_MATRIX_ITCM_SIZE		(0xf << 0)
> +#define AT91_MATRIX_ITCM_0		(0 << 0)
> +#define AT91_MATRIX_ITCM_16		(5 << 0)
> +#define AT91_MATRIX_ITCM_32		(6 << 0)
> +#define AT91_MATRIX_ITCM_64		(7 << 0)
> +#define	AT91_MATRIX_DTCM_SIZE		(0xf << 4)
> +#define	AT91_MATRIX_DTCM_0		(0 << 4)
> +#define	AT91_MATRIX_DTCM_16		(5 << 4)
> +#define AT91_MATRIX_DTCM_32		(6 << 4)
> +#define AT91_MATRIX_DTCM_64		(7 << 4)
> +
> +#define AT91_MATRIX_PRAS(o, x)		((o) + ((x) * 0x8))
> +#define AT91_MATRIX_PRBS(o, x)		((o) + ((x) * 0x8) + 0x4)
> +#define AT91_MATRIX_MPR_MSK(x)		(3 << ((x) * 0x4))
> +
> +#define AT91_MATRIX_MRC(o)		(o)
> +#define AT91_MATRIX_RCB(x)		BIT(x)
> +
> +#define AT91_MATRIX_EBICSA(o)		(o)
> +#define AT91_MATRIX_CSA(cs, val)	(val << (cs))
> +#define AT91_MATRIX_DBPUC		BIT(8)
> +#define AT91_MATRIX_DBPDC		BIT(9)
> +#define AT91_MATRIX_VDDIOMSEL		BIT(16)
> +#define AT91_MATRIX_VDDIOMSEL_1_8V	(0 << 16)
> +#define AT91_MATRIX_VDDIOMSEL_3_3V	(1 << 16)
> +#define AT91_MATRIX_EBI_IOSR		BIT(17)
> +#define AT91_MATRIX_DDR_IOSR		BIT(18)
> +#define AT91_MATRIX_NFD0_SELECT		BIT(24)
> +#define AT91_MATRIX_DDR_MP_EN		BIT(25)
> +#define AT91_MATRIX_EBI_NUM_CS		8
> +
> +#define AT91_MATRIX_WPMR(o)		(o)
> +#define AT91_MATRIX_WPSR(o)		(o)
> +
> +#endif /* _LINUX_MFD_SYSCON_ATMEL_MATRIX_H */

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v2 04/11] mfd: syscon: Add Atmel SMC binding doc

[Lee Jones]

On Wed, 05 Nov 2014, Boris Brezillon wrote:

> The SMC registers are used to configure Atmel EBI (External Bus Interface)
> to interface with standard memory devices (NAND, NOR, SRAM or specialized
> devices like FPGAs).
> 
> Declare this memory region as a syscon, so that different drivers can
> configure the SMC interface (mostly timing configuration) according to
> their need.
> 
> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> ---
>  Documentation/devicetree/bindings/mfd/atmel-smc.txt | 19 +++++++++++++++++++
>  1 file changed, 19 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/atmel-smc.txt
> 
> diff --git a/Documentation/devicetree/bindings/mfd/atmel-smc.txt b/Documentation/devicetree/bindings/mfd/atmel-smc.txt
> new file mode 100644
> index 0000000..0c0cc3d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/atmel-smc.txt
> @@ -0,0 +1,19 @@
> +* Device tree bindings for Atmel SMC (Static Memory Controller)
> +
> +The SMC registers are used to configure Atmel EBI (External Bus Interface)
> +to interface with standard memory devices (NAND, NOR, SRAM or specialized
> +devices like FPGAs).
> +
> +Required properties:
> +- compatible:		should be one of the following
> +			"atmel,at91sam9260-smc", "syscon"
> +			"atmel,sama5d3-smc", "syscon"
> +- reg:			contains offset/length value of the SMC memory
> +			region.

I'd be happier if the sentences started with uppercase letters, but
nothing too offensive or controversial here:

Acked-by: Lee Jones <lee.jones@linaro.org>

> +Example:
> +
> +smc: smc@ffffc000 {
> +	compatible = "atmel,sama5d3-smc", "syscon";
> +	reg = <0xffffc000 0x1000>;
> +};

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v2 02/11] mfd: syscon: Add Atmel Matrix bus DT binding documentation

[Lee Jones]

On Wed, 05 Nov 2014, Boris Brezillon wrote:

> The Matrix registers are provided to configure internal bus behavior on
> at91 SoCs.
> Some registers might be access by several drivers (e.g. to configure
> external memory bus timings), hence we declare this register set as a
> syscon device.
> 
> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> ---
>  .../devicetree/bindings/mfd/atmel-matrix.txt       | 24 ++++++++++++++++++++++
>  1 file changed, 24 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/atmel-matrix.txt
> 
> diff --git a/Documentation/devicetree/bindings/mfd/atmel-matrix.txt b/Documentation/devicetree/bindings/mfd/atmel-matrix.txt
> new file mode 100644
> index 0000000..405cac9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/atmel-matrix.txt
> @@ -0,0 +1,24 @@
> +* Device tree bindings for Atmel Bus Matrix
> +
> +The Bus Matrix registers are used to configure Atmel SoCs internal bus
> +behavior (master/slave priorities, undefined burst length type, ...)
> +
> +Required properties:
> +- compatible:		should be one of the following
> +			"atmel,at91sam9260-matrix", "syscon"
> +			"atmel,at91sam9261-matrix", "syscon"
> +			"atmel,at91sam9263-matrix", "syscon"
> +			"atmel,at91sam9263-matrix", "syscon"
> +			"atmel,at91sam9g45-matrix", "syscon"
> +			"atmel,at91sam9n12-matrix", "syscon"
> +			"atmel,at91sam9x5-matrix", "syscon"
> +			"atmel,sama5d3-matrix", "syscon"
> +- reg:			contains offset/length value of the Bus Matrix
> +			memory region.

Same comments as before:

Acked-by: Lee Jones <lee.jones@linaro.org>

> +Example:
> +
> +matrix: matrix@ffffec00 {
> +	compatible = "atmel,sama5d3-matrix", "syscon";
> +	reg = <0xffffec00 0x200>;
> +};

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v2 03/11] mfd: syscon: Add atmel-smc registers definition

[Lee Jones]

On Wed, 05 Nov 2014, Boris Brezillon wrote:

> Atmel AT91 SoCs have a memory range reserved for SMC (Static Memory
> Controller) configuration.
> Expose those registers so that drivers can make use of the smc syscon
> declared in at91 DTs.
> 
> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> ---
>  include/linux/mfd/syscon/atmel-smc.h | 60 ++++++++++++++++++++++++++++++++++++
>  1 file changed, 60 insertions(+)
>  create mode 100644 include/linux/mfd/syscon/atmel-smc.h

Acked-by: Lee Jones <lee.jones@linaro.org>

Any idea who will take this set?

> diff --git a/include/linux/mfd/syscon/atmel-smc.h b/include/linux/mfd/syscon/atmel-smc.h
> new file mode 100644
> index 0000000..430f486
> --- /dev/null
> +++ b/include/linux/mfd/syscon/atmel-smc.h
> @@ -0,0 +1,60 @@
> +/*
> + * Atmel SMC (Static Memory Controller) register offsets and bit definitions.
> + *
> + * Copyright (C) 2014 Atmel
> + * Copyright (C) 2014 Free Electrons
> + *
> + * Author: Boris Brezillon <boris.brezillon@free-electrons.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#ifndef _LINUX_MFD_SYSCON_ATMEL_SMC_H_
> +#define _LINUX_MFD_SYSCON_ATMEL_SMC_H_
> +
> +#include <linux/regmap.h>
> +
> +#define AT91SAM9_SMC_GENERIC_OFFSET	0x00
> +#define AT91SAM9_SMC_GENERIC_BLK_SZ	0x10
> +
> +#define SAMA5_SMC_GENERIC_OFFSET	0x600
> +#define SAMA5_SMC_GENERIC_BLK_SZ	0x14
> +
> +#define AT91SAM9_SMC_SETUP(o)		((o) + 0x00)
> +#define AT91SAM9_SMC_NWESETUP_SHFT	0
> +#define AT91SAM9_SMC_NCS_WRSETUP_SHFT	8
> +#define AT91SAM9_SMC_NRDSETUP_SHFT	16
> +#define AT91SAM9_SMC_NCS_NRDSETUP_SHFT	24
> +
> +#define AT91SAM9_SMC_PULSE(o)		((o) + 0x04)
> +
> +#define AT91SAM9_SMC_CYCLE(o)		((o) + 0x08)
> +
> +#define AT91SAM9_SMC_MODE(o)		((o) + 0x0c)
> +#define SAMA5_SMC_MODE(o)		((o) + 0x10)
> +#define AT91_SMC_READMODE		BIT(0)
> +#define AT91_SMC_WRITEMODE		BIT(1)
> +#define AT91_SMC_EXNWMODE		GENMASK(5, 4)
> +#define AT91_SMC_EXNWMODE_DISABLE	(0 << 4)
> +#define AT91_SMC_EXNWMODE_FROZEN	(2 << 4)
> +#define AT91_SMC_EXNWMODE_READY		(3 << 4)
> +#define AT91_SMC_BAT			BIT(8)
> +#define AT91_SMC_BAT_SELECT		(0 << 8)
> +#define AT91_SMC_BAT_WRITE		(1 << 8)
> +#define AT91_SMC_DBW			GENMASK(13, 12)
> +#define AT91_SMC_DBW_8			(0 << 12)
> +#define AT91_SMC_DBW_16			(1 << 12)
> +#define AT91_SMC_DBW_32			(2 << 12)
> +#define AT91_SMC_TDF			GENMASK(19, 16)
> +#define AT91_SMC_TDF_(x)		(((x) & 0xf) << 16)
> +#define AT91_SMC_TDFMODE		BIT(20)
> +#define AT91_SMC_PMEN			BIT(24)
> +#define AT91_SMC_PS			GENMASK(29, 28)
> +#define AT91_SMC_PS_4			(0 << 28)
> +#define AT91_SMC_PS_8			(1 << 28)
> +#define AT91_SMC_PS_16			(2 << 28)
> +#define AT91_SMC_PS_32			(3 << 28)
> +
> +#endif /* _LINUX_MFD_SYSCON_ATMEL_SMC_H_ */

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v2 03/11] mfd: syscon: Add atmel-smc registers definition

[Boris Brezillon]

Hi Lee,

Sorry for the late reply.

On Mon, 10 Nov 2014 09:57:28 +0000
Lee Jones <lee.jones@linaro.org> wrote:

> On Wed, 05 Nov 2014, Boris Brezillon wrote:
> 
> > Atmel AT91 SoCs have a memory range reserved for SMC (Static Memory
> > Controller) configuration.
> > Expose those registers so that drivers can make use of the smc syscon
> > declared in at91 DTs.
> > 
> > Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> > ---
> >  include/linux/mfd/syscon/atmel-smc.h | 60 ++++++++++++++++++++++++++++++++++++
> >  1 file changed, 60 insertions(+)
> >  create mode 100644 include/linux/mfd/syscon/atmel-smc.h
> 
> Acked-by: Lee Jones <lee.jones@linaro.org>
> 
> Any idea who will take this set?

I guess you could take patch 1 to 4 and Nicolas would take the other
ones (unless there's a maintainer for memory controller drivers).
Or, if we don't want to have dependency issues, Nicolas can take all of
them.

Nicolas, any preference ?

Regards,

Boris

-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Re: [PATCH v2 03/11] mfd: syscon: Add atmel-smc registers definition

[Nicolas Ferre]

Le 01/12/2014 10:38, Boris Brezillon a écrit :
> Hi Lee,
> 
> Sorry for the late reply.
> 
> On Mon, 10 Nov 2014 09:57:28 +0000
> Lee Jones <lee.jones@linaro.org> wrote:
> 
>> On Wed, 05 Nov 2014, Boris Brezillon wrote:
>>
>>> Atmel AT91 SoCs have a memory range reserved for SMC (Static Memory
>>> Controller) configuration.
>>> Expose those registers so that drivers can make use of the smc syscon
>>> declared in at91 DTs.
>>>
>>> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
>>> ---
>>>  include/linux/mfd/syscon/atmel-smc.h | 60 ++++++++++++++++++++++++++++++++++++
>>>  1 file changed, 60 insertions(+)
>>>  create mode 100644 include/linux/mfd/syscon/atmel-smc.h
>>
>> Acked-by: Lee Jones <lee.jones@linaro.org>
>>
>> Any idea who will take this set?
> 
> I guess you could take patch 1 to 4 and Nicolas would take the other
> ones (unless there's a maintainer for memory controller drivers).
> Or, if we don't want to have dependency issues, Nicolas can take all of
> them.
> 
> Nicolas, any preference ?

Yes, I'd prefer to take the whole series. So add your Acked-by tags and
I take all in one of my at91-x.yy-drivers branches.

Bye,
-- 
Nicolas Ferre