* [PATCH v7 0/4] pci: iproc: Add Broadcom iProc PCIe support
@ 2015-03-13 0:48 Ray Jui
2015-03-13 0:48 ` [PATCH v7 1/4] PCI: Export symbols of PCI functions Ray Jui
` (4 more replies)
0 siblings, 5 replies; 6+ messages in thread
From: Ray Jui @ 2015-03-13 0:48 UTC (permalink / raw)
To: Bjorn Helgaas, Arnd Bergmann, Hauke Mehrtens, Paul Bolle,
Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
Cc: Florian Fainelli, Dmitry Torokhov, Anatol Pomazau, Scott Branden,
linux-pci, linux-kernel, linux-arm-kernel,
bcm-kernel-feedback-list, devicetree, Ray Jui
This patch series adds the support for Broadcom iProc PCIe controller
pcie-iproc.c servers as the common core driver, and front-end bus
interface needs to be added to support different bus interfaces
pcie-iproc-pltfm.c contains the support for the platform bus interface
Changes from v6:
- Fix print formatting
- Fix section mismatch warning by removing __init from the probe function
- Fix Kconfig to force it only compiling for ARM based platforms
Changes from v5:
- Sync code base to v4.0-rc2
- Change export symbols of common PCI functions to GPL only
- Add comment to describe how configuration register access are protected
at the higher layer through 'pci_lock'
- Use generic PCI functions for configuration register access and implement
'map_bus' callback to support it
- Move 'pci_fixup_irqs' to before devices are added to the bus
- Remove 'extern' from function prototype declared in the header
Changes from v4:
- iProc PCIe driver module support was not included in patch series v4.
This patch series (v5) fixes it
Changes from v3:
- Export symbols of several PCI functions so they can be used by drivers
compiled as kernel module
- Add additional support to the Broadcom iProc PCIe driver so it can be
installed/uninstalled as kernel loadable module
Changes from v2:
- Major rework of the PCIe driver to factor out common generic code from
front-end bus interface. Support for generic platform bus interface is
also added
- Adapt to several new PCI APIs that have been introduced lately
Changes from v1:
- Add standard PCI interrupt DT properties "#interrupt-cells",
"interrupt-map-mask" and "interrupt-map" so legacy INTx interrupts can be
supported by using standard PCI OF IRQ parsing function
- Get rid of custom IRQ mapping function in the driver. Use
of_irq_parse_and_map_pci instead
Ray Jui (4):
PCI: Export symbols of PCI functions
pci: iProc: define iProc PCIe platform bus binding
pci: iproc: Add Broadcom iProc PCIe support
ARM: dts: enable PCIe support for Cygnus
.../devicetree/bindings/pci/brcm,iproc-pcie.txt | 63 +++++
arch/arm/boot/dts/bcm-cygnus.dtsi | 42 +++
arch/arm/boot/dts/bcm958300k.dts | 8 +
drivers/pci/host/Kconfig | 17 ++
drivers/pci/host/Makefile | 2 +
drivers/pci/host/pcie-iproc-pltfm.c | 108 ++++++++
drivers/pci/host/pcie-iproc.c | 268 ++++++++++++++++++++
drivers/pci/host/pcie-iproc.h | 42 +++
drivers/pci/pci.c | 1 +
drivers/pci/probe.c | 1 +
drivers/pci/remove.c | 2 +
drivers/pci/setup-bus.c | 1 +
drivers/pci/setup-irq.c | 1 +
13 files changed, 556 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
create mode 100644 drivers/pci/host/pcie-iproc-pltfm.c
create mode 100644 drivers/pci/host/pcie-iproc.c
create mode 100644 drivers/pci/host/pcie-iproc.h
--
1.7.9.5
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v7 1/4] PCI: Export symbols of PCI functions
2015-03-13 0:48 [PATCH v7 0/4] pci: iproc: Add Broadcom iProc PCIe support Ray Jui
@ 2015-03-13 0:48 ` Ray Jui
2015-03-13 0:48 ` [PATCH v7 2/4] pci: iProc: define iProc PCIe platform bus binding Ray Jui
` (3 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Ray Jui @ 2015-03-13 0:48 UTC (permalink / raw)
To: Bjorn Helgaas, Arnd Bergmann, Hauke Mehrtens, Paul Bolle,
Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
Cc: Florian Fainelli, Dmitry Torokhov, Anatol Pomazau, Scott Branden,
linux-pci, linux-kernel, linux-arm-kernel,
bcm-kernel-feedback-list, devicetree, Ray Jui
Export symbols of the following PCI functions so they can be referenced
by a PCI driver compiled as a kernel loadable module:
pci_common_swizzle
pci_create_root_bus
pci_stop_root_bus
pci_remove_root_bus
pci_assign_unassigned_bus_resources
pci_fixup_irqs
Signed-off-by: Ray Jui <rjui@broadcom.com>
---
drivers/pci/pci.c | 1 +
drivers/pci/probe.c | 1 +
drivers/pci/remove.c | 2 ++
drivers/pci/setup-bus.c | 1 +
drivers/pci/setup-irq.c | 1 +
5 files changed, 6 insertions(+)
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index 81f06e8..14e7f3c 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -2492,6 +2492,7 @@ u8 pci_common_swizzle(struct pci_dev *dev, u8 *pinp)
*pinp = pin;
return PCI_SLOT(dev->devfn);
}
+EXPORT_SYMBOL_GPL(pci_common_swizzle);
/**
* pci_release_region - Release a PCI bar
diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index 8d2f400..f13a78a 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -1993,6 +1993,7 @@ err_out:
kfree(b);
return NULL;
}
+EXPORT_SYMBOL_GPL(pci_create_root_bus);
int pci_bus_insert_busn_res(struct pci_bus *b, int bus, int bus_max)
{
diff --git a/drivers/pci/remove.c b/drivers/pci/remove.c
index 8bd76c9..8a280e9 100644
--- a/drivers/pci/remove.c
+++ b/drivers/pci/remove.c
@@ -139,6 +139,7 @@ void pci_stop_root_bus(struct pci_bus *bus)
/* stop the host bridge */
device_release_driver(&host_bridge->dev);
}
+EXPORT_SYMBOL_GPL(pci_stop_root_bus);
void pci_remove_root_bus(struct pci_bus *bus)
{
@@ -158,3 +159,4 @@ void pci_remove_root_bus(struct pci_bus *bus)
/* remove the host bridge */
device_unregister(&host_bridge->dev);
}
+EXPORT_SYMBOL_GPL(pci_remove_root_bus);
diff --git a/drivers/pci/setup-bus.c b/drivers/pci/setup-bus.c
index e3e17f3..8169597 100644
--- a/drivers/pci/setup-bus.c
+++ b/drivers/pci/setup-bus.c
@@ -1750,3 +1750,4 @@ void pci_assign_unassigned_bus_resources(struct pci_bus *bus)
__pci_bus_assign_resources(bus, &add_list, NULL);
BUG_ON(!list_empty(&add_list));
}
+EXPORT_SYMBOL_GPL(pci_assign_unassigned_bus_resources);
diff --git a/drivers/pci/setup-irq.c b/drivers/pci/setup-irq.c
index 4e2d595..95c225b 100644
--- a/drivers/pci/setup-irq.c
+++ b/drivers/pci/setup-irq.c
@@ -65,3 +65,4 @@ void pci_fixup_irqs(u8 (*swizzle)(struct pci_dev *, u8 *),
for_each_pci_dev(dev)
pdev_fixup_irq(dev, swizzle, map_irq);
}
+EXPORT_SYMBOL_GPL(pci_fixup_irqs);
--
1.7.9.5
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v7 2/4] pci: iProc: define iProc PCIe platform bus binding
2015-03-13 0:48 [PATCH v7 0/4] pci: iproc: Add Broadcom iProc PCIe support Ray Jui
2015-03-13 0:48 ` [PATCH v7 1/4] PCI: Export symbols of PCI functions Ray Jui
@ 2015-03-13 0:48 ` Ray Jui
2015-03-13 0:48 ` [PATCH v7 3/4] pci: iproc: Add Broadcom iProc PCIe support Ray Jui
` (2 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Ray Jui @ 2015-03-13 0:48 UTC (permalink / raw)
To: Bjorn Helgaas, Arnd Bergmann, Hauke Mehrtens, Paul Bolle,
Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
Cc: Florian Fainelli, Dmitry Torokhov, Anatol Pomazau, Scott Branden,
linux-pci, linux-kernel, linux-arm-kernel,
bcm-kernel-feedback-list, devicetree, Ray Jui
Document the Broadcom iProc PCIe platform interface device tree binding
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
.../devicetree/bindings/pci/brcm,iproc-pcie.txt | 63 ++++++++++++++++++++
1 file changed, 63 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
diff --git a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
new file mode 100644
index 0000000..f7ce50e
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
@@ -0,0 +1,63 @@
+* Broadcom iProc PCIe controller with the platform bus interface
+
+Required properties:
+- compatible: Must be "brcm,iproc-pcie"
+- reg: base address and length of the PCIe controller I/O register space
+- #interrupt-cells: set to <1>
+- interrupt-map-mask and interrupt-map, standard PCI properties to define the
+ mapping of the PCIe interface to interrupt numbers
+- linux,pci-domain: PCI domain ID. Should be unique for each host controller
+- bus-range: PCI bus numbers covered
+- #address-cells: set to <3>
+- #size-cells: set to <2>
+- device_type: set to "pci"
+- ranges: ranges for the PCI memory and I/O regions
+
+Optional properties:
+- phys: phandle of the PCIe PHY device
+- phy-names: must be "pcie-phy"
+
+Example:
+ pcie0: pcie@18012000 {
+ compatible = "brcm,iproc-pcie";
+ reg = <0x18012000 0x1000>;
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
+
+ linux,pci-domain = <0>;
+
+ bus-range = <0x00 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x81000000 0 0 0x28000000 0 0x00010000
+ 0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
+
+ phys = <&phy 0 5>;
+ phy-names = "pcie-phy";
+ };
+
+ pcie1: pcie@18013000 {
+ compatible = "brcm,iproc-pcie";
+ reg = <0x18013000 0x1000>;
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
+
+ linux,pci-domain = <1>;
+
+ bus-range = <0x00 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x81000000 0 0 0x48000000 0 0x00010000
+ 0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
+
+ phys = <&phy 1 6>;
+ phy-names = "pcie-phy";
+ };
--
1.7.9.5
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v7 3/4] pci: iproc: Add Broadcom iProc PCIe support
2015-03-13 0:48 [PATCH v7 0/4] pci: iproc: Add Broadcom iProc PCIe support Ray Jui
2015-03-13 0:48 ` [PATCH v7 1/4] PCI: Export symbols of PCI functions Ray Jui
2015-03-13 0:48 ` [PATCH v7 2/4] pci: iProc: define iProc PCIe platform bus binding Ray Jui
@ 2015-03-13 0:48 ` Ray Jui
2015-03-13 0:48 ` [PATCH v7 4/4] ARM: dts: enable PCIe support for Cygnus Ray Jui
2015-03-19 21:05 ` [PATCH v7 0/4] pci: iproc: Add Broadcom iProc PCIe support Bjorn Helgaas
4 siblings, 0 replies; 6+ messages in thread
From: Ray Jui @ 2015-03-13 0:48 UTC (permalink / raw)
To: Bjorn Helgaas, Arnd Bergmann, Hauke Mehrtens, Paul Bolle,
Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
Cc: Florian Fainelli, Dmitry Torokhov, Anatol Pomazau, Scott Branden,
linux-pci, linux-kernel, linux-arm-kernel,
bcm-kernel-feedback-list, devicetree, Ray Jui
This adds the support for Broadcom iProc PCIe controller
pcie-iproc.c servers as the common core driver, and front-end bus
interface needs to be added to support different bus interfaces
pcie-iproc-pltfm.c contains the support for the platform bus interface
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
drivers/pci/host/Kconfig | 17 +++
drivers/pci/host/Makefile | 2 +
drivers/pci/host/pcie-iproc-pltfm.c | 108 ++++++++++++++
drivers/pci/host/pcie-iproc.c | 268 +++++++++++++++++++++++++++++++++++
drivers/pci/host/pcie-iproc.h | 42 ++++++
5 files changed, 437 insertions(+)
create mode 100644 drivers/pci/host/pcie-iproc-pltfm.c
create mode 100644 drivers/pci/host/pcie-iproc.c
create mode 100644 drivers/pci/host/pcie-iproc.h
diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
index 7b892a9..feccd0d 100644
--- a/drivers/pci/host/Kconfig
+++ b/drivers/pci/host/Kconfig
@@ -106,4 +106,21 @@ config PCI_VERSATILE
bool "ARM Versatile PB PCI controller"
depends on ARCH_VERSATILE
+config PCIE_IPROC
+ tristate "Broadcom iProc PCIe controller"
+ help
+ This enables the iProc PCIe core controller support for Broadcom's
+ iProc family of SoCs. An appropriate bus interface driver also needs
+ to be enabled
+
+config PCIE_IPROC_PLTFM
+ tristate "Broadcom iProc PCIe platform bus driver"
+ depends on ARCH_BCM_IPROC || (ARM && COMPILE_TEST)
+ depends on OF
+ select PCIE_IPROC
+ default ARCH_BCM_IPROC
+ help
+ Say Y here if you want to use the Broadcom iProc PCIe controller
+ through the generic platform bus interface
+
endmenu
diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile
index e61d91c..2e02d20 100644
--- a/drivers/pci/host/Makefile
+++ b/drivers/pci/host/Makefile
@@ -13,3 +13,5 @@ obj-$(CONFIG_PCIE_XILINX) += pcie-xilinx.o
obj-$(CONFIG_PCI_XGENE) += pci-xgene.o
obj-$(CONFIG_PCI_LAYERSCAPE) += pci-layerscape.o
obj-$(CONFIG_PCI_VERSATILE) += pci-versatile.o
+obj-$(CONFIG_PCIE_IPROC) += pcie-iproc.o
+obj-$(CONFIG_PCIE_IPROC_PLTFM) += pcie-iproc-pltfm.o
diff --git a/drivers/pci/host/pcie-iproc-pltfm.c b/drivers/pci/host/pcie-iproc-pltfm.c
new file mode 100644
index 0000000..afad6c2
--- /dev/null
+++ b/drivers/pci/host/pcie-iproc-pltfm.c
@@ -0,0 +1,108 @@
+/*
+ * Copyright (C) 2015 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/of_address.h>
+#include <linux/of_pci.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+
+#include "pcie-iproc.h"
+
+static int iproc_pcie_pltfm_probe(struct platform_device *pdev)
+{
+ struct iproc_pcie *pcie;
+ struct device_node *np = pdev->dev.of_node;
+ struct resource reg;
+ resource_size_t iobase = 0;
+ LIST_HEAD(res);
+ int ret;
+
+ pcie = devm_kzalloc(&pdev->dev, sizeof(struct iproc_pcie), GFP_KERNEL);
+ if (!pcie)
+ return -ENOMEM;
+
+ pcie->dev = &pdev->dev;
+ platform_set_drvdata(pdev, pcie);
+
+ ret = of_address_to_resource(np, 0, ®);
+ if (ret < 0) {
+ dev_err(pcie->dev, "unable to obtain controller resources\n");
+ return ret;
+ }
+
+ pcie->base = devm_ioremap(pcie->dev, reg.start, resource_size(®));
+ if (!pcie->base) {
+ dev_err(pcie->dev, "unable to map controller registers\n");
+ return -ENOMEM;
+ }
+
+ /* PHY use is optional */
+ pcie->phy = devm_phy_get(&pdev->dev, "pcie-phy");
+ if (IS_ERR(pcie->phy)) {
+ if (PTR_ERR(pcie->phy) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+ pcie->phy = NULL;
+ }
+
+ ret = of_pci_get_host_bridge_resources(np, 0, 0xff, &res, &iobase);
+ if (ret) {
+ dev_err(pcie->dev,
+ "unable to get PCI host bridge resources\n");
+ return ret;
+ }
+
+ pcie->resources = &res;
+
+ ret = iproc_pcie_setup(pcie);
+ if (ret) {
+ dev_err(pcie->dev, "PCIe controller setup failed\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int iproc_pcie_pltfm_remove(struct platform_device *pdev)
+{
+ struct iproc_pcie *pcie = platform_get_drvdata(pdev);
+
+ return iproc_pcie_remove(pcie);
+}
+
+static const struct of_device_id iproc_pcie_of_match_table[] = {
+ { .compatible = "brcm,iproc-pcie", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, iproc_pcie_of_match_table);
+
+static struct platform_driver iproc_pcie_pltfm_driver = {
+ .driver = {
+ .name = "iproc-pcie",
+ .of_match_table = of_match_ptr(iproc_pcie_of_match_table),
+ },
+ .probe = iproc_pcie_pltfm_probe,
+ .remove = iproc_pcie_pltfm_remove,
+};
+module_platform_driver(iproc_pcie_pltfm_driver);
+
+MODULE_AUTHOR("Ray Jui <rjui@broadcom.com>");
+MODULE_DESCRIPTION("Broadcom iPROC PCIe platform driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/pci/host/pcie-iproc.c b/drivers/pci/host/pcie-iproc.c
new file mode 100644
index 0000000..329e1b5
--- /dev/null
+++ b/drivers/pci/host/pcie-iproc.c
@@ -0,0 +1,268 @@
+/*
+ * Copyright (C) 2014 Hauke Mehrtens <hauke@hauke-m.de>
+ * Copyright (C) 2015 Broadcom Corporatcommon ion
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/msi.h>
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/mbus.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/of_address.h>
+#include <linux/of_pci.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+
+#include "pcie-iproc.h"
+
+#define CLK_CONTROL_OFFSET 0x000
+#define EP_MODE_SURVIVE_PERST_SHIFT 1
+#define EP_MODE_SURVIVE_PERST BIT(EP_MODE_SURVIVE_PERST_SHIFT)
+#define RC_PCIE_RST_OUTPUT_SHIFT 0
+#define RC_PCIE_RST_OUTPUT BIT(RC_PCIE_RST_OUTPUT_SHIFT)
+
+#define CFG_IND_ADDR_OFFSET 0x120
+#define CFG_IND_ADDR_MASK 0x00001ffc
+
+#define CFG_IND_DATA_OFFSET 0x124
+
+#define CFG_ADDR_OFFSET 0x1f8
+#define CFG_ADDR_BUS_NUM_SHIFT 20
+#define CFG_ADDR_BUS_NUM_MASK 0x0ff00000
+#define CFG_ADDR_DEV_NUM_SHIFT 15
+#define CFG_ADDR_DEV_NUM_MASK 0x000f8000
+#define CFG_ADDR_FUNC_NUM_SHIFT 12
+#define CFG_ADDR_FUNC_NUM_MASK 0x00007000
+#define CFG_ADDR_REG_NUM_SHIFT 2
+#define CFG_ADDR_REG_NUM_MASK 0x00000ffc
+#define CFG_ADDR_CFG_TYPE_SHIFT 0
+#define CFG_ADDR_CFG_TYPE_MASK 0x00000003
+
+#define CFG_DATA_OFFSET 0x1fc
+
+#define SYS_RC_INTX_EN 0x330
+#define SYS_RC_INTX_MASK 0xf
+
+static inline struct iproc_pcie *sys_to_pcie(struct pci_sys_data *sys)
+{
+ return sys->private_data;
+}
+
+/**
+ * Note access to the configuration registers are protected at the higher layer
+ * by 'pci_lock' in drivers/pci/access.c
+ */
+static void __iomem *iproc_pcie_map_cfg_bus(struct pci_bus *bus,
+ unsigned int devfn,
+ int where)
+{
+ struct pci_sys_data *sys = bus->sysdata;
+ struct iproc_pcie *pcie = sys_to_pcie(sys);
+ unsigned slot = PCI_SLOT(devfn);
+ unsigned fn = PCI_FUNC(devfn);
+ unsigned busno = bus->number;
+ u32 val;
+
+ /* root complex access */
+ if (busno == 0) {
+ if (slot >= 1)
+ return NULL;
+ writel(where & CFG_IND_ADDR_MASK,
+ pcie->base + CFG_IND_ADDR_OFFSET);
+ return (pcie->base + CFG_IND_DATA_OFFSET);
+ }
+
+ if (fn > 1)
+ return NULL;
+
+ /* EP device access */
+ val = (busno << CFG_ADDR_BUS_NUM_SHIFT) |
+ (slot << CFG_ADDR_DEV_NUM_SHIFT) |
+ (fn << CFG_ADDR_FUNC_NUM_SHIFT) |
+ (where & CFG_ADDR_REG_NUM_MASK) |
+ (1 & CFG_ADDR_CFG_TYPE_MASK);
+ writel(val, pcie->base + CFG_ADDR_OFFSET);
+
+ return (pcie->base + CFG_DATA_OFFSET);
+}
+
+static struct pci_ops iproc_pcie_ops = {
+ .map_bus = iproc_pcie_map_cfg_bus,
+ .read = pci_generic_config_read32,
+ .write = pci_generic_config_write32,
+};
+
+static void iproc_pcie_reset(struct iproc_pcie *pcie)
+{
+ u32 val;
+
+ /*
+ * Configure the PCIe controller as root complex and send a downstream
+ * reset
+ */
+ val = EP_MODE_SURVIVE_PERST | RC_PCIE_RST_OUTPUT;
+ writel(val, pcie->base + CLK_CONTROL_OFFSET);
+ udelay(250);
+ val &= ~EP_MODE_SURVIVE_PERST;
+ writel(val, pcie->base + CLK_CONTROL_OFFSET);
+ msleep(250);
+}
+
+static int iproc_pcie_check_link(struct iproc_pcie *pcie, struct pci_bus *bus)
+{
+ u8 hdr_type;
+ u32 link_ctrl;
+ u16 pos, link_status;
+ int link_is_active = 0;
+
+ /* make sure we are not in EP mode */
+ pci_bus_read_config_byte(bus, 0, PCI_HEADER_TYPE, &hdr_type);
+ if ((hdr_type & 0x7f) != PCI_HEADER_TYPE_BRIDGE) {
+ dev_err(pcie->dev, "in EP mode, hdr=%#02x\n", hdr_type);
+ return -EFAULT;
+ }
+
+ /* force class to PCI_CLASS_BRIDGE_PCI (0x0604) */
+ pci_bus_write_config_word(bus, 0, PCI_CLASS_DEVICE,
+ PCI_CLASS_BRIDGE_PCI);
+
+ /* check link status to see if link is active */
+ pos = pci_bus_find_capability(bus, 0, PCI_CAP_ID_EXP);
+ pci_bus_read_config_word(bus, 0, pos + PCI_EXP_LNKSTA, &link_status);
+ if (link_status & PCI_EXP_LNKSTA_NLW)
+ link_is_active = 1;
+
+ if (!link_is_active) {
+ /* try GEN 1 link speed */
+#define PCI_LINK_STATUS_CTRL_2_OFFSET 0x0dc
+#define PCI_TARGET_LINK_SPEED_MASK 0xf
+#define PCI_TARGET_LINK_SPEED_GEN2 0x2
+#define PCI_TARGET_LINK_SPEED_GEN1 0x1
+ pci_bus_read_config_dword(bus, 0,
+ PCI_LINK_STATUS_CTRL_2_OFFSET,
+ &link_ctrl);
+ if ((link_ctrl & PCI_TARGET_LINK_SPEED_MASK) ==
+ PCI_TARGET_LINK_SPEED_GEN2) {
+ link_ctrl &= ~PCI_TARGET_LINK_SPEED_MASK;
+ link_ctrl |= PCI_TARGET_LINK_SPEED_GEN1;
+ pci_bus_write_config_dword(bus, 0,
+ PCI_LINK_STATUS_CTRL_2_OFFSET,
+ link_ctrl);
+ msleep(100);
+
+ pos = pci_bus_find_capability(bus, 0, PCI_CAP_ID_EXP);
+ pci_bus_read_config_word(bus, 0, pos + PCI_EXP_LNKSTA,
+ &link_status);
+ if (link_status & PCI_EXP_LNKSTA_NLW)
+ link_is_active = 1;
+ }
+ }
+
+ dev_info(pcie->dev, "link: %s\n", link_is_active ? "UP" : "DOWN");
+
+ return link_is_active ? 0 : -ENODEV;
+}
+
+static void iproc_pcie_enable(struct iproc_pcie *pcie)
+{
+ writel(SYS_RC_INTX_MASK, pcie->base + SYS_RC_INTX_EN);
+}
+
+int iproc_pcie_setup(struct iproc_pcie *pcie)
+{
+ int ret;
+ struct pci_bus *bus;
+
+ if (!pcie || !pcie->dev || !pcie->base)
+ return -EINVAL;
+
+ if (pcie->phy) {
+ ret = phy_init(pcie->phy);
+ if (ret) {
+ dev_err(pcie->dev, "unable to initialize PCIe PHY\n");
+ return ret;
+ }
+
+ ret = phy_power_on(pcie->phy);
+ if (ret) {
+ dev_err(pcie->dev, "unable to power on PCIe PHY\n");
+ goto err_exit_phy;
+ }
+
+ }
+
+ iproc_pcie_reset(pcie);
+
+ pcie->sysdata.private_data = pcie;
+
+ bus = pci_create_root_bus(pcie->dev, 0, &iproc_pcie_ops,
+ &pcie->sysdata, pcie->resources);
+ if (!bus) {
+ dev_err(pcie->dev, "unable to create PCI root bus\n");
+ ret = -ENOMEM;
+ goto err_power_off_phy;
+ }
+ pcie->root_bus = bus;
+
+ ret = iproc_pcie_check_link(pcie, bus);
+ if (ret) {
+ dev_err(pcie->dev, "no PCIe EP device detected\n");
+ goto err_rm_root_bus;
+ }
+
+ iproc_pcie_enable(pcie);
+
+ pci_scan_child_bus(bus);
+ pci_assign_unassigned_bus_resources(bus);
+ pci_fixup_irqs(pci_common_swizzle, of_irq_parse_and_map_pci);
+ pci_bus_add_devices(bus);
+
+ return 0;
+
+err_rm_root_bus:
+ pci_stop_root_bus(bus);
+ pci_remove_root_bus(bus);
+
+err_power_off_phy:
+ if (pcie->phy)
+ phy_power_off(pcie->phy);
+err_exit_phy:
+ if (pcie->phy)
+ phy_exit(pcie->phy);
+
+ return ret;
+}
+EXPORT_SYMBOL(iproc_pcie_setup);
+
+int iproc_pcie_remove(struct iproc_pcie *pcie)
+{
+ pci_stop_root_bus(pcie->root_bus);
+ pci_remove_root_bus(pcie->root_bus);
+
+ if (pcie->phy) {
+ phy_power_off(pcie->phy);
+ phy_exit(pcie->phy);
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(iproc_pcie_remove);
+
+MODULE_AUTHOR("Ray Jui <rjui@broadcom.com>");
+MODULE_DESCRIPTION("Broadcom iPROC PCIe common driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/pci/host/pcie-iproc.h b/drivers/pci/host/pcie-iproc.h
new file mode 100644
index 0000000..e28075e
--- /dev/null
+++ b/drivers/pci/host/pcie-iproc.h
@@ -0,0 +1,42 @@
+/*
+ * Copyright (C) 2014-2015 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _PCIE_IPROC_H
+#define _PCIE_IPROC_H
+
+#define IPROC_PCIE_MAX_NUM_IRQS 6
+
+/**
+ * iProc PCIe device
+ * @dev: pointer to device data structure
+ * @base: PCIe host controller I/O register base
+ * @resources: linked list of all PCI resources
+ * @sysdata: Per PCI controller data
+ * @root_bus: pointer to root bus
+ * @phy: optional PHY device that controls the Serdes
+ * @irqs: interrupt IDs
+ */
+struct iproc_pcie {
+ struct device *dev;
+ void __iomem *base;
+ struct list_head *resources;
+ struct pci_sys_data sysdata;
+ struct pci_bus *root_bus;
+ struct phy *phy;
+ int irqs[IPROC_PCIE_MAX_NUM_IRQS];
+};
+
+int iproc_pcie_setup(struct iproc_pcie *pcie);
+int iproc_pcie_remove(struct iproc_pcie *pcie);
+
+#endif /* _PCIE_IPROC_H */
--
1.7.9.5
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v7 4/4] ARM: dts: enable PCIe support for Cygnus
2015-03-13 0:48 [PATCH v7 0/4] pci: iproc: Add Broadcom iProc PCIe support Ray Jui
` (2 preceding siblings ...)
2015-03-13 0:48 ` [PATCH v7 3/4] pci: iproc: Add Broadcom iProc PCIe support Ray Jui
@ 2015-03-13 0:48 ` Ray Jui
2015-03-19 21:05 ` [PATCH v7 0/4] pci: iproc: Add Broadcom iProc PCIe support Bjorn Helgaas
4 siblings, 0 replies; 6+ messages in thread
From: Ray Jui @ 2015-03-13 0:48 UTC (permalink / raw)
To: Bjorn Helgaas, Arnd Bergmann, Hauke Mehrtens, Paul Bolle,
Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
Cc: Florian Fainelli, Dmitry Torokhov, Anatol Pomazau, Scott Branden,
linux-pci, linux-kernel, linux-arm-kernel,
bcm-kernel-feedback-list, devicetree, Ray Jui
Add PCIe device nodes in bcm-cygnus.dtsi but keep them disabled there.
Only enable them for bcm958300k where PCIe interfaces are populated
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
arch/arm/boot/dts/bcm-cygnus.dtsi | 42 +++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/bcm958300k.dts | 8 +++++++
2 files changed, 50 insertions(+)
diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index ff5fb6a..ee0c6e4 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -90,6 +90,48 @@
status = "disabled";
};
+ pcie0: pcie@18012000 {
+ compatible = "brcm,iproc-pcie";
+ reg = <0x18012000 0x1000>;
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
+
+ linux,pci-domain = <0>;
+
+ bus-range = <0x00 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x81000000 0 0 0x28000000 0 0x00010000
+ 0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
+
+ status = "disabled";
+ };
+
+ pcie1: pcie@18013000 {
+ compatible = "brcm,iproc-pcie";
+ reg = <0x18013000 0x1000>;
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
+
+ linux,pci-domain = <1>;
+
+ bus-range = <0x00 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x81000000 0 0 0x48000000 0 0x00010000
+ 0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
+
+ status = "disabled";
+ };
+
uart0: serial@18020000 {
compatible = "snps,dw-apb-uart";
reg = <0x18020000 0x100>;
diff --git a/arch/arm/boot/dts/bcm958300k.dts b/arch/arm/boot/dts/bcm958300k.dts
index f1bb36f..c9eb856 100644
--- a/arch/arm/boot/dts/bcm958300k.dts
+++ b/arch/arm/boot/dts/bcm958300k.dts
@@ -47,6 +47,14 @@
bootargs = "console=ttyS0,115200";
};
+ pcie0: pcie@18012000 {
+ status = "okay";
+ };
+
+ pcie1: pcie@18013000 {
+ status = "okay";
+ };
+
uart3: serial@18023000 {
status = "okay";
};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v7 0/4] pci: iproc: Add Broadcom iProc PCIe support
2015-03-13 0:48 [PATCH v7 0/4] pci: iproc: Add Broadcom iProc PCIe support Ray Jui
` (3 preceding siblings ...)
2015-03-13 0:48 ` [PATCH v7 4/4] ARM: dts: enable PCIe support for Cygnus Ray Jui
@ 2015-03-19 21:05 ` Bjorn Helgaas
4 siblings, 0 replies; 6+ messages in thread
From: Bjorn Helgaas @ 2015-03-19 21:05 UTC (permalink / raw)
To: Ray Jui
Cc: Arnd Bergmann, Hauke Mehrtens, Paul Bolle, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Florian Fainelli, Dmitry Torokhov, Anatol Pomazau, Scott Branden,
linux-pci, linux-kernel, linux-arm-kernel,
bcm-kernel-feedback-list, devicetree
[+cc Florian]
On Thu, Mar 12, 2015 at 05:48:48PM -0700, Ray Jui wrote:
> This patch series adds the support for Broadcom iProc PCIe controller
>
> pcie-iproc.c servers as the common core driver, and front-end bus
> interface needs to be added to support different bus interfaces
>
> pcie-iproc-pltfm.c contains the support for the platform bus interface
>
> Changes from v6:
> - Fix print formatting
> - Fix section mismatch warning by removing __init from the probe function
> - Fix Kconfig to force it only compiling for ARM based platforms
>
> Changes from v5:
> - Sync code base to v4.0-rc2
> - Change export symbols of common PCI functions to GPL only
> - Add comment to describe how configuration register access are protected
> at the higher layer through 'pci_lock'
> - Use generic PCI functions for configuration register access and implement
> 'map_bus' callback to support it
> - Move 'pci_fixup_irqs' to before devices are added to the bus
> - Remove 'extern' from function prototype declared in the header
>
> Changes from v4:
> - iProc PCIe driver module support was not included in patch series v4.
> This patch series (v5) fixes it
>
> Changes from v3:
> - Export symbols of several PCI functions so they can be used by drivers
> compiled as kernel module
> - Add additional support to the Broadcom iProc PCIe driver so it can be
> installed/uninstalled as kernel loadable module
>
> Changes from v2:
> - Major rework of the PCIe driver to factor out common generic code from
> front-end bus interface. Support for generic platform bus interface is
> also added
> - Adapt to several new PCI APIs that have been introduced lately
>
> Changes from v1:
> - Add standard PCI interrupt DT properties "#interrupt-cells",
> "interrupt-map-mask" and "interrupt-map" so legacy INTx interrupts can be
> supported by using standard PCI OF IRQ parsing function
> - Get rid of custom IRQ mapping function in the driver. Use
> of_irq_parse_and_map_pci instead
>
> Ray Jui (4):
> PCI: Export symbols of PCI functions
> pci: iProc: define iProc PCIe platform bus binding
> pci: iproc: Add Broadcom iProc PCIe support
> ARM: dts: enable PCIe support for Cygnus
I applied patches 1-3 to pci/host-iproc for v4.1, thanks! I didn't apply
patch 4 because Florian said he'd already applied it to devicetree/next.
I normally look for a MAINTAINERS entry, but your existing entry for
"BROADCOM CYGNUS/IPROC ARM ARCHITECTURE" has wildcards that already include
these new files.
> .../devicetree/bindings/pci/brcm,iproc-pcie.txt | 63 +++++
> arch/arm/boot/dts/bcm-cygnus.dtsi | 42 +++
> arch/arm/boot/dts/bcm958300k.dts | 8 +
> drivers/pci/host/Kconfig | 17 ++
> drivers/pci/host/Makefile | 2 +
> drivers/pci/host/pcie-iproc-pltfm.c | 108 ++++++++
> drivers/pci/host/pcie-iproc.c | 268 ++++++++++++++++++++
> drivers/pci/host/pcie-iproc.h | 42 +++
> drivers/pci/pci.c | 1 +
> drivers/pci/probe.c | 1 +
> drivers/pci/remove.c | 2 +
> drivers/pci/setup-bus.c | 1 +
> drivers/pci/setup-irq.c | 1 +
> 13 files changed, 556 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
> create mode 100644 drivers/pci/host/pcie-iproc-pltfm.c
> create mode 100644 drivers/pci/host/pcie-iproc.c
> create mode 100644 drivers/pci/host/pcie-iproc.h
>
> --
> 1.7.9.5
>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2015-03-19 21:05 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-03-13 0:48 [PATCH v7 0/4] pci: iproc: Add Broadcom iProc PCIe support Ray Jui
2015-03-13 0:48 ` [PATCH v7 1/4] PCI: Export symbols of PCI functions Ray Jui
2015-03-13 0:48 ` [PATCH v7 2/4] pci: iProc: define iProc PCIe platform bus binding Ray Jui
2015-03-13 0:48 ` [PATCH v7 3/4] pci: iproc: Add Broadcom iProc PCIe support Ray Jui
2015-03-13 0:48 ` [PATCH v7 4/4] ARM: dts: enable PCIe support for Cygnus Ray Jui
2015-03-19 21:05 ` [PATCH v7 0/4] pci: iproc: Add Broadcom iProc PCIe support Bjorn Helgaas
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).