[PATCH v4 0/8] ARM: dts: exynos5: labels for overriding nodes

[PATCH v4 0/8] ARM: dts: exynos5: labels for overriding nodes

[Krzysztof Kozlowski]

Hi,


Changes since v3
================
1. Rebased on current Kukjin's for-next branch:
   v4.1-rc3-34-gfcfae6b049cf

Changes since v2
================
1. New patch 8/8: ARM: dts: Use labels for overriding nodes
   in exynos5422-odroidxu3
2. To avoid conflicts rebased on my "for-next" branch of
   https://github.com/krzk/linux
   The branch above contains some patches for Exynos5 boards
   applied from LKML.

Changes since v1
================
1. Re-phrased the description (phandle->label). Suggested by Arnd.


Description
===========
The label-based notation reduces possible mistakes when overriding
nodes by child DTSI and board files and reduces duplication
of addresses.

The patchset refactors Exynos5 boards to use labels for overriding nodes.

Tested by comparison of decompiled DTB for each commit.


Best regards,
Krzysztof


Krzysztof Kozlowski (8):
  ARM: dts: Add labels to exynos5 nodes
  ARM: dts: Use labels for overriding nodes in exynos5250
  ARM: dts: Remove duplicated I2C7 nodes in exynos5250-snow
  ARM: dts: Use labels for overriding nodes in exynos5420-arndale-octa
  ARM: dts: Use labels for overriding nodes in exynos542x
  ARM: dts: Use labels for overriding nodes in exynos5420-smdk5420
  ARM: dts: Use labels for overriding nodes in exynos5440 boards
  ARM: dts: Use labels for overriding nodes in exynos5422-odroidxu3

 arch/arm/boot/dts/exynos5.dtsi                |   6 +-
 arch/arm/boot/dts/exynos5250-snow.dts         |  46 +-
 arch/arm/boot/dts/exynos5250.dtsi             |  82 ++--
 arch/arm/boot/dts/exynos5420-arndale-octa.dts | 634 ++++++++++++-------------
 arch/arm/boot/dts/exynos5420-peach-pit.dts    |   2 +-
 arch/arm/boot/dts/exynos5420-smdk5420.dts     | 645 +++++++++++++-------------
 arch/arm/boot/dts/exynos5420.dtsi             |  82 ++--
 arch/arm/boot/dts/exynos5422-odroidxu3.dts    | 568 +++++++++++------------
 arch/arm/boot/dts/exynos5440-sd5v1.dts        |  10 +-
 arch/arm/boot/dts/exynos5440-ssdk5440.dts     |  85 ++--
 arch/arm/boot/dts/exynos5440.dtsi             |   4 +-
 arch/arm/boot/dts/exynos5800-peach-pi.dts     |   2 +-
 12 files changed, 1082 insertions(+), 1084 deletions(-)

-- 
2.1.4

[PATCH v4 1/8] ARM: dts: Add labels to exynos5 nodes

[Krzysztof Kozlowski]

Add new labels to certain nodes so they could be easily referenced by
Exynos5 board DTS files.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
 arch/arm/boot/dts/exynos5.dtsi    | 6 +++---
 arch/arm/boot/dts/exynos5440.dtsi | 4 ++--
 2 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5.dtsi b/arch/arm/boot/dts/exynos5.dtsi
index a0cc0b6f8f96..110dbd4fb884 100644
--- a/arch/arm/boot/dts/exynos5.dtsi
+++ b/arch/arm/boot/dts/exynos5.dtsi
@@ -81,14 +81,14 @@
 		interrupts = <0 54 0>;
 	};
 
-	rtc@101E0000 {
+	rtc: rtc@101E0000 {
 		compatible = "samsung,s3c6410-rtc";
 		reg = <0x101E0000 0x100>;
 		interrupts = <0 43 0>, <0 44 0>;
 		status = "disabled";
 	};
 
-	fimd@14400000 {
+	fimd: fimd@14400000 {
 		compatible = "samsung,exynos5250-fimd";
 		interrupt-parent = <&combiner>;
 		reg = <0x14400000 0x40000>;
@@ -98,7 +98,7 @@
 		status = "disabled";
 	};
 
-	dp-controller@145B0000 {
+	dp: dp-controller@145B0000 {
 		compatible = "samsung,exynos5-dp";
 		reg = <0x145B0000 0x1000>;
 		interrupts = <10 3>;
diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi
index 59d9416b3b03..f18b51f2eeaa 100644
--- a/arch/arm/boot/dts/exynos5440.dtsi
+++ b/arch/arm/boot/dts/exynos5440.dtsi
@@ -279,7 +279,7 @@
 		clock-names = "usbhost";
 	};
 
-	pcie@290000 {
+	pcie_0: pcie@290000 {
 		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
 		reg = <0x290000 0x1000
 			0x270000 0x1000
@@ -300,7 +300,7 @@
 		status = "disabled";
 	};
 
-	pcie@2a0000 {
+	pcie_1: pcie@2a0000 {
 		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
 		reg = <0x2a0000 0x1000
 			0x272000 0x1000
-- 
2.1.4

[PATCH v4 2/8] ARM: dts: Use labels for overriding nodes in exynos5250

[Krzysztof Kozlowski]

Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
 arch/arm/boot/dts/exynos5250.dtsi | 82 +++++++++++++++++++--------------------
 1 file changed, 41 insertions(+), 41 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 257e2f10525d..916871bb3f05 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -241,13 +241,6 @@
 		clock-names = "mfc";
 	};
 
-	rtc: rtc@101E0000 {
-		clocks = <&clock CLK_RTC>;
-		clock-names = "rtc";
-		interrupt-parent = <&pmu_system_controller>;
-		status = "disabled";
-	};
-
 	tmu: tmu@10060000 {
 		compatible = "samsung,exynos5250-tmu";
 		reg = <0x10060000 0x100>;
@@ -276,26 +269,6 @@
 		};
 	};
 
-	serial@12C00000 {
-		clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
-		clock-names = "uart", "clk_uart_baud0";
-	};
-
-	serial@12C10000 {
-		clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
-		clock-names = "uart", "clk_uart_baud0";
-	};
-
-	serial@12C20000 {
-		clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
-		clock-names = "uart", "clk_uart_baud0";
-	};
-
-	serial@12C30000 {
-		clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
-		clock-names = "uart", "clk_uart_baud0";
-	};
-
 	sata: sata@122F0000 {
 		compatible = "snps,dwc-ahci";
 		samsung,sata-freq = <66>;
@@ -778,20 +751,6 @@
 		#phy-cells = <0>;
 	};
 
-	dp: dp-controller@145B0000 {
-		power-domains = <&pd_disp1>;
-		clocks = <&clock CLK_DP>;
-		clock-names = "dp";
-		phys = <&dp_phy>;
-		phy-names = "dp";
-	};
-
-	fimd: fimd@14400000 {
-		power-domains = <&pd_disp1>;
-		clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
-		clock-names = "sclk_fimd", "fimd";
-	};
-
 	adc: adc@12D10000 {
 		compatible = "samsung,exynos-adc-v1";
 		reg = <0x12D10000 0x100>;
@@ -812,3 +771,44 @@
 		clock-names = "secss";
 	};
 };
+
+&dp {
+	power-domains = <&pd_disp1>;
+	clocks = <&clock CLK_DP>;
+	clock-names = "dp";
+	phys = <&dp_phy>;
+	phy-names = "dp";
+};
+
+&fimd {
+	power-domains = <&pd_disp1>;
+	clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
+	clock-names = "sclk_fimd", "fimd";
+};
+
+&rtc {
+	clocks = <&clock CLK_RTC>;
+	clock-names = "rtc";
+	interrupt-parent = <&pmu_system_controller>;
+	status = "disabled";
+};
+
+&serial_0 {
+	clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
+	clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_1 {
+	clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
+	clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_2 {
+	clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
+	clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_3 {
+	clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
+	clock-names = "uart", "clk_uart_baud0";
+};
-- 
2.1.4

[PATCH v4 3/8] ARM: dts: Remove duplicated I2C7 nodes in exynos5250-snow

[Krzysztof Kozlowski]

The i2c_7 node (i2c@12CD0000) with LVDS bridge child node was put in
Exynos5250 Snow DTS file twice. Move the LVDS bridge to proper existing
i2c_7 node.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
 arch/arm/boot/dts/exynos5250-snow.dts | 46 +++++++++++++++++------------------
 1 file changed, 22 insertions(+), 24 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index 1eca97ee4bd6..b7f4122df456 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -177,30 +177,6 @@
 		};
 	};
 
-	i2c@12CD0000 {
-		ptn3460: lvds-bridge@20 {
-			compatible = "nxp,ptn3460";
-			reg = <0x20>;
-			powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
-			reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
-			edid-emulation = <5>;
-
-			ports {
-				port@0 {
-					bridge_out: endpoint {
-						remote-endpoint = <&panel_in>;
-					};
-				};
-
-				port@1 {
-					bridge_in: endpoint {
-						remote-endpoint = <&dp_out>;
-					};
-				};
-			};
-		};
-	};
-
 	sound {
 		compatible = "google,snow-audio-max98095";
 
@@ -507,6 +483,28 @@
 	samsung,i2c-sda-delay = <100>;
 	samsung,i2c-max-bus-freq = <66000>;
 
+	ptn3460: lvds-bridge@20 {
+		compatible = "nxp,ptn3460";
+		reg = <0x20>;
+		powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
+		edid-emulation = <5>;
+
+		ports {
+			port@0 {
+				bridge_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+
+			port@1 {
+				bridge_in: endpoint {
+					remote-endpoint = <&dp_out>;
+				};
+			};
+		};
+	};
+
 	max98095: codec@11 {
 		compatible = "maxim,max98095";
 		reg = <0x11>;
-- 
2.1.4

[PATCH v4 4/8] ARM: dts: Use labels for overriding nodes in exynos5420-arndale-octa

[Krzysztof Kozlowski]

Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
 arch/arm/boot/dts/exynos5420-arndale-octa.dts | 634 +++++++++++++-------------
 1 file changed, 317 insertions(+), 317 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5420-arndale-octa.dts b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
index 9924b870423f..eeb4ac22cfce 100644
--- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts
+++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
@@ -39,323 +39,6 @@
 		};
 	};
 
-	codec@11000000 {
-		samsung,mfc-r = <0x43000000 0x800000>;
-		samsung,mfc-l = <0x51000000 0x800000>;
-	};
-
-	mmc@12200000 {
-		status = "okay";
-		broken-cd;
-		card-detect-delay = <200>;
-		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <0 4>;
-		samsung,dw-mshc-ddr-timing = <0 2>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
-		vmmc-supply = <&ldo10_reg>;
-		bus-width = <8>;
-		cap-mmc-highspeed;
-	};
-
-	mmc@12220000 {
-		status = "okay";
-		card-detect-delay = <200>;
-		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <2 3>;
-		samsung,dw-mshc-ddr-timing = <1 2>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
-		vmmc-supply = <&ldo19_reg>;
-		vqmmc-supply = <&ldo13_reg>;
-		bus-width = <4>;
-		cap-sd-highspeed;
-	};
-
-	hsi2c_4: i2c@12CA0000 {
-		status = "okay";
-
-		s2mps11_pmic@66 {
-			compatible = "samsung,s2mps11-pmic";
-			reg = <0x66>;
-			s2mps11,buck2-ramp-delay = <12>;
-			s2mps11,buck34-ramp-delay = <12>;
-			s2mps11,buck16-ramp-delay = <12>;
-			s2mps11,buck6-ramp-enable = <1>;
-			s2mps11,buck2-ramp-enable = <1>;
-			s2mps11,buck3-ramp-enable = <1>;
-			s2mps11,buck4-ramp-enable = <1>;
-
-			interrupt-parent = <&gpx3>;
-			interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&s2mps11_irq>;
-
-			s2mps11_osc: clocks {
-				#clock-cells = <1>;
-				clock-output-names = "s2mps11_ap",
-						"s2mps11_cp", "s2mps11_bt";
-			};
-
-			regulators {
-				ldo1_reg: LDO1 {
-					regulator-name = "PVDD_ALIVE_1V0";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
-					regulator-always-on;
-				};
-
-				ldo2_reg: LDO2 {
-					regulator-name = "PVDD_APIO_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo3_reg: LDO3 {
-					regulator-name = "PVDD_APIO_MMCON_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo4_reg: LDO4 {
-					regulator-name = "PVDD_ADC_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo5_reg: LDO5 {
-					regulator-name = "PVDD_PLL_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo6_reg: LDO6 {
-					regulator-name = "PVDD_ANAIP_1V0";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
-				};
-
-				ldo7_reg: LDO7 {
-					regulator-name = "PVDD_ANAIP_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo8_reg: LDO8 {
-					regulator-name = "PVDD_ABB_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo9_reg: LDO9 {
-					regulator-name = "PVDD_USB_3V3";
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					regulator-always-on;
-				};
-
-				ldo10_reg: LDO10 {
-					regulator-name = "PVDD_PRE_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo11_reg: LDO11 {
-					regulator-name = "PVDD_USB_1V0";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
-					regulator-always-on;
-				};
-
-				ldo12_reg: LDO12 {
-					regulator-name = "PVDD_HSIC_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo13_reg: LDO13 {
-					regulator-name = "PVDD_APIO_MMCOFF_2V8";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-				};
-
-				ldo15_reg: LDO15 {
-					regulator-name = "PVDD_PERI_2V8";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-				};
-
-				ldo16_reg: LDO16 {
-					regulator-name = "PVDD_PERI_3V3";
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-				};
-
-				ldo18_reg: LDO18 {
-					regulator-name = "PVDD_EMMC_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo19_reg: LDO19 {
-					regulator-name = "PVDD_TFLASH_2V8";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-				};
-
-				ldo20_reg: LDO20 {
-					regulator-name = "PVDD_BTWIFI_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo21_reg: LDO21 {
-					regulator-name = "PVDD_CAM1IO_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo23_reg: LDO23 {
-					regulator-name = "PVDD_MIFS_1V1";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					regulator-always-on;
-				};
-
-				ldo24_reg: LDO24 {
-					regulator-name = "PVDD_CAM1_AVDD_2V8";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-				};
-
-				ldo26_reg: LDO26 {
-					regulator-name = "PVDD_CAM0_AF_2V8";
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-				};
-
-				ldo27_reg: LDO27 {
-					regulator-name = "PVDD_G3DS_1V0";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-				};
-
-				ldo28_reg: LDO28 {
-					regulator-name = "PVDD_TSP_3V3";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-				};
-
-				ldo29_reg: LDO29 {
-					regulator-name = "PVDD_AUDIO_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo31_reg: LDO31 {
-					regulator-name = "PVDD_PERI_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo32_reg: LDO32 {
-					regulator-name = "PVDD_LCD_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo33_reg: LDO33 {
-					regulator-name = "PVDD_CAM0IO_1V8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo35_reg: LDO35 {
-					regulator-name = "PVDD_CAM0_DVDD_1V2";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-				};
-
-				ldo38_reg: LDO38 {
-					regulator-name = "PVDD_CAM0_AVDD_2V8";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-				};
-
-				buck1_reg: BUCK1 {
-					regulator-name = "PVDD_MIF_1V1";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1100000>;
-					regulator-always-on;
-				};
-
-				buck2_reg: BUCK2 {
-					regulator-name = "vdd_arm";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1000000>;
-					regulator-always-on;
-				};
-
-				buck3_reg: BUCK3 {
-					regulator-name = "PVDD_INT_1V0";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1000000>;
-					regulator-always-on;
-				};
-
-				buck4_reg: BUCK4 {
-					regulator-name = "PVDD_G3D_1V0";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1000000>;
-				};
-
-				buck5_reg: BUCK5 {
-					regulator-name = "PVDD_LPDDR3_1V2";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1200000>;
-					regulator-always-on;
-				};
-
-				buck6_reg: BUCK6 {
-					regulator-name = "PVDD_KFC_1V0";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1000000>;
-					regulator-always-on;
-				};
-
-				buck7_reg: BUCK7 {
-					regulator-name = "VIN_LLDO_1V4";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1400000>;
-					regulator-always-on;
-				};
-
-				buck8_reg: BUCK8 {
-					regulator-name = "VIN_MLDO_2V0";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <2000000>;
-					regulator-always-on;
-				};
-
-				buck9_reg: BUCK9 {
-					regulator-name = "VIN_HLDO_3V5";
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3500000>;
-					regulator-always-on;
-				};
-
-				buck10_reg: BUCK10 {
-					regulator-name = "PVDD_EMMCF_2V8";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-				};
-			};
-		};
-	};
-
 	gpio_keys {
 		compatible = "gpio-keys";
 
@@ -376,6 +59,323 @@
 	status = "disabled";
 };
 
+&hsi2c_4 {
+	status = "okay";
+
+	s2mps11_pmic@66 {
+		compatible = "samsung,s2mps11-pmic";
+		reg = <0x66>;
+		s2mps11,buck2-ramp-delay = <12>;
+		s2mps11,buck34-ramp-delay = <12>;
+		s2mps11,buck16-ramp-delay = <12>;
+		s2mps11,buck6-ramp-enable = <1>;
+		s2mps11,buck2-ramp-enable = <1>;
+		s2mps11,buck3-ramp-enable = <1>;
+		s2mps11,buck4-ramp-enable = <1>;
+
+		interrupt-parent = <&gpx3>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&s2mps11_irq>;
+
+		s2mps11_osc: clocks {
+			#clock-cells = <1>;
+			clock-output-names = "s2mps11_ap",
+					"s2mps11_cp", "s2mps11_bt";
+		};
+
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "PVDD_ALIVE_1V0";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "PVDD_APIO_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "PVDD_APIO_MMCON_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "PVDD_ADC_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo5_reg: LDO5 {
+				regulator-name = "PVDD_PLL_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "PVDD_ANAIP_1V0";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+			};
+
+			ldo7_reg: LDO7 {
+				regulator-name = "PVDD_ANAIP_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo8_reg: LDO8 {
+				regulator-name = "PVDD_ABB_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "PVDD_USB_3V3";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "PVDD_PRE_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo11_reg: LDO11 {
+				regulator-name = "PVDD_USB_1V0";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			ldo12_reg: LDO12 {
+				regulator-name = "PVDD_HSIC_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo13_reg: LDO13 {
+				regulator-name = "PVDD_APIO_MMCOFF_2V8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			ldo15_reg: LDO15 {
+				regulator-name = "PVDD_PERI_2V8";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			ldo16_reg: LDO16 {
+				regulator-name = "PVDD_PERI_3V3";
+				regulator-min-microvolt = <2200000>;
+				regulator-max-microvolt = <2200000>;
+			};
+
+			ldo18_reg: LDO18 {
+				regulator-name = "PVDD_EMMC_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo19_reg: LDO19 {
+				regulator-name = "PVDD_TFLASH_2V8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			ldo20_reg: LDO20 {
+				regulator-name = "PVDD_BTWIFI_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo21_reg: LDO21 {
+				regulator-name = "PVDD_CAM1IO_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo23_reg: LDO23 {
+				regulator-name = "PVDD_MIFS_1V1";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			ldo24_reg: LDO24 {
+				regulator-name = "PVDD_CAM1_AVDD_2V8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			ldo26_reg: LDO26 {
+				regulator-name = "PVDD_CAM0_AF_2V8";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			ldo27_reg: LDO27 {
+				regulator-name = "PVDD_G3DS_1V0";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			ldo28_reg: LDO28 {
+				regulator-name = "PVDD_TSP_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			ldo29_reg: LDO29 {
+				regulator-name = "PVDD_AUDIO_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo31_reg: LDO31 {
+				regulator-name = "PVDD_PERI_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo32_reg: LDO32 {
+				regulator-name = "PVDD_LCD_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo33_reg: LDO33 {
+				regulator-name = "PVDD_CAM0IO_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo35_reg: LDO35 {
+				regulator-name = "PVDD_CAM0_DVDD_1V2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			ldo38_reg: LDO38 {
+				regulator-name = "PVDD_CAM0_AVDD_2V8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "PVDD_MIF_1V1";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "PVDD_INT_1V0";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "PVDD_G3D_1V0";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1000000>;
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "PVDD_LPDDR3_1V2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "PVDD_KFC_1V0";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			buck7_reg: BUCK7 {
+				regulator-name = "VIN_LLDO_1V4";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+			};
+
+			buck8_reg: BUCK8 {
+				regulator-name = "VIN_MLDO_2V0";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-always-on;
+			};
+
+			buck9_reg: BUCK9 {
+				regulator-name = "VIN_HLDO_3V5";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3500000>;
+				regulator-always-on;
+			};
+
+			buck10_reg: BUCK10 {
+				regulator-name = "PVDD_EMMCF_2V8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+		};
+	};
+};
+
+&mfc {
+	samsung,mfc-r = <0x43000000 0x800000>;
+	samsung,mfc-l = <0x51000000 0x800000>;
+};
+
+&mmc_0 {
+	status = "okay";
+	broken-cd;
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+	vmmc-supply = <&ldo10_reg>;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+};
+
+&mmc_2 {
+	status = "okay";
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+	vmmc-supply = <&ldo19_reg>;
+	vqmmc-supply = <&ldo13_reg>;
+	bus-width = <4>;
+	cap-sd-highspeed;
+};
+
 &pinctrl_0 {
 	s2mps11_irq: s2mps11-irq {
 		samsung,pins = "gpx3-2";
-- 
2.1.4

[PATCH v4 5/8] ARM: dts: Use labels for overriding nodes in exynos542x

[Krzysztof Kozlowski]

Usage of labels instead of full paths reduces possible mistakes when
overriding nodes. Additionally remove duplicated serial and uart labels
for serial.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
 arch/arm/boot/dts/exynos5420-peach-pit.dts |  2 +-
 arch/arm/boot/dts/exynos5420.dtsi          | 82 +++++++++++++++---------------
 arch/arm/boot/dts/exynos5800-peach-pi.dts  |  2 +-
 3 files changed, 43 insertions(+), 43 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
index 146e71118a72..8f4d76c5e11c 100644
--- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
+++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
@@ -1027,7 +1027,7 @@
 	};
 };
 
-&uart_3 {
+&serial_3 {
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi
index db6cd6302667..487d2176605f 100644
--- a/arch/arm/boot/dts/exynos5420.dtsi
+++ b/arch/arm/boot/dts/exynos5420.dtsi
@@ -328,13 +328,6 @@
 		interrupts = <0 47 0>;
 	};
 
-	rtc: rtc@101E0000 {
-		clocks = <&clock CLK_RTC>;
-		clock-names = "rtc";
-		interrupt-parent = <&pmu_system_controller>;
-		status = "disabled";
-	};
-
 	amba {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -505,26 +498,6 @@
 		status = "disabled";
 	};
 
-	uart_0: serial@12C00000 {
-		clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
-		clock-names = "uart", "clk_uart_baud0";
-	};
-
-	uart_1: serial@12C10000 {
-		clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
-		clock-names = "uart", "clk_uart_baud0";
-	};
-
-	uart_2: serial@12C20000 {
-		clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
-		clock-names = "uart", "clk_uart_baud0";
-	};
-
-	uart_3: serial@12C30000 {
-		clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
-		clock-names = "uart", "clk_uart_baud0";
-	};
-
 	pwm: pwm@12dd0000 {
 		compatible = "samsung,exynos4210-pwm";
 		reg = <0x12dd0000 0x100>;
@@ -540,14 +513,6 @@
 		#phy-cells = <0>;
 	};
 
-	dp: dp-controller@145B0000 {
-		clocks = <&clock CLK_DP1>;
-		clock-names = "dp";
-		phys = <&dp_phy>;
-		phy-names = "dp";
-		power-domains = <&disp_pd>;
-	};
-
 	mipi_phy: video-phy@10040714 {
 		compatible = "samsung,s5pv210-mipi-video-phy";
 		syscon = <&pmu_system_controller>;
@@ -567,12 +532,6 @@
 		status = "disabled";
 	};
 
-	fimd: fimd@14400000 {
-		clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
-		clock-names = "sclk_fimd", "fimd";
-		power-domains = <&disp_pd>;
-	};
-
 	adc: adc@12D10000 {
 		compatible = "samsung,exynos-adc-v2";
 		reg = <0x12D10000 0x100>;
@@ -972,3 +931,44 @@
 		samsung,pmureg-phandle = <&pmu_system_controller>;
 	};
 };
+
+&dp {
+	clocks = <&clock CLK_DP1>;
+	clock-names = "dp";
+	phys = <&dp_phy>;
+	phy-names = "dp";
+	power-domains = <&disp_pd>;
+};
+
+&fimd {
+	clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
+	clock-names = "sclk_fimd", "fimd";
+	power-domains = <&disp_pd>;
+};
+
+&rtc {
+	clocks = <&clock CLK_RTC>;
+	clock-names = "rtc";
+	interrupt-parent = <&pmu_system_controller>;
+	status = "disabled";
+};
+
+&serial_0 {
+	clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
+	clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_1 {
+	clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
+	clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_2 {
+	clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
+	clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_3 {
+	clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
+	clock-names = "uart", "clk_uart_baud0";
+};
diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
index 02eb8b15374f..7d5b386b5ae6 100644
--- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
+++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
@@ -990,7 +990,7 @@
 	};
 };
 
-&uart_3 {
+&serial_3 {
 	status = "okay";
 };
 
-- 
2.1.4

[PATCH v4 6/8] ARM: dts: Use labels for overriding nodes in exynos5420-smdk5420

[Krzysztof Kozlowski]

Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
 arch/arm/boot/dts/exynos5420-smdk5420.dts | 645 +++++++++++++++---------------
 1 file changed, 323 insertions(+), 322 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts
index 9103f2381a6d..98871f972c8a 100644
--- a/arch/arm/boot/dts/exynos5420-smdk5420.dts
+++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts
@@ -64,105 +64,6 @@
 		};
 	};
 
-	rtc@101E0000 {
-		status = "okay";
-	};
-
-	codec@11000000 {
-		samsung,mfc-r = <0x43000000 0x800000>;
-		samsung,mfc-l = <0x51000000 0x800000>;
-	};
-
-	mmc@12200000 {
-		status = "okay";
-		broken-cd;
-		card-detect-delay = <200>;
-		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <0 4>;
-		samsung,dw-mshc-ddr-timing = <0 2>;
-		samsung,dw-mshc-hs400-timing = <0 2>;
-		samsung,read-strobe-delay = <90>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8
-			     &sd0_rclk>;
-		bus-width = <8>;
-		cap-mmc-highspeed;
-	};
-
-	mmc@12220000 {
-		status = "okay";
-		card-detect-delay = <200>;
-		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <2 3>;
-		samsung,dw-mshc-ddr-timing = <1 2>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
-		bus-width = <4>;
-		cap-sd-highspeed;
-	};
-
-	dp-controller@145B0000 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&dp_hpd>;
-		samsung,color-space = <0>;
-		samsung,dynamic-range = <0>;
-		samsung,ycbcr-coeff = <0>;
-		samsung,color-depth = <1>;
-		samsung,link-rate = <0x0a>;
-		samsung,lane-count = <4>;
-		status = "okay";
-	};
-
-	fimd@14400000 {
-		status = "okay";
-		display-timings {
-			native-mode = <&timing0>;
-			timing0: timing@0 {
-				clock-frequency = <50000>;
-				hactive = <2560>;
-				vactive = <1600>;
-				hfront-porch = <48>;
-				hback-porch = <80>;
-				hsync-len = <32>;
-				vback-porch = <16>;
-				vfront-porch = <8>;
-				vsync-len = <6>;
-			};
-		};
-	};
-
-	pinctrl@13400000 {
-		hdmi_hpd_irq: hdmi-hpd-irq {
-			samsung,pins = "gpx3-7";
-			samsung,pin-function = <0>;
-			samsung,pin-pud = <1>;
-			samsung,pin-drv = <0>;
-		};
-	};
-
-	pinctrl@14000000 {
-		usb300_vbus_en: usb300-vbus-en {
-			samsung,pins = "gpg0-5";
-			samsung,pin-function = <1>;
-			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
-		};
-
-		usb301_vbus_en: usb301-vbus-en {
-			samsung,pins = "gpg1-4";
-			samsung,pin-function = <1>;
-			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
-		};
-	};
-
-	hdmi@14530000 {
-		status = "okay";
-		hpd-gpio = <&gpx3 7 0>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&hdmi_hpd_irq>;
-	};
-
 	usb300_vbus_reg: regulator-usb300 {
 		compatible = "regulator-fixed";
 		regulator-name = "VBUS0";
@@ -185,238 +86,338 @@
 		enable-active-high;
 	};
 
-	phy@12100000 {
-		vbus-supply = <&usb300_vbus_reg>;
-	};
+};
 
-	phy@12500000 {
-		vbus-supply = <&usb301_vbus_reg>;
+&dp {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dp_hpd>;
+	samsung,color-space = <0>;
+	samsung,dynamic-range = <0>;
+	samsung,ycbcr-coeff = <0>;
+	samsung,color-depth = <1>;
+	samsung,link-rate = <0x0a>;
+	samsung,lane-count = <4>;
+	status = "okay";
+};
+
+&fimd {
+	status = "okay";
+	display-timings {
+		native-mode = <&timing0>;
+		timing0: timing@0 {
+			clock-frequency = <50000>;
+			hactive = <2560>;
+			vactive = <1600>;
+			hfront-porch = <48>;
+			hback-porch = <80>;
+			hsync-len = <32>;
+			vback-porch = <16>;
+			vfront-porch = <8>;
+			vsync-len = <6>;
+		};
 	};
+};
 
-	i2c_2: i2c@12C80000 {
-		samsung,i2c-sda-delay = <100>;
-		samsung,i2c-max-bus-freq = <66000>;
-		status = "okay";
+&hdmi {
+	status = "okay";
+	hpd-gpio = <&gpx3 7 0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_hpd_irq>;
+};
 
-		hdmiddc@50 {
-			compatible = "samsung,exynos4210-hdmiddc";
-			reg = <0x50>;
+&hsi2c_4 {
+	status = "okay";
+
+	s2mps11_pmic@66 {
+		compatible = "samsung,s2mps11-pmic";
+		reg = <0x66>;
+		s2mps11,buck2-ramp-delay = <12>;
+		s2mps11,buck34-ramp-delay = <12>;
+		s2mps11,buck16-ramp-delay = <12>;
+		s2mps11,buck6-ramp-enable = <1>;
+		s2mps11,buck2-ramp-enable = <1>;
+		s2mps11,buck3-ramp-enable = <1>;
+		s2mps11,buck4-ramp-enable = <1>;
+
+		s2mps11_osc: clocks {
+			#clock-cells = <1>;
+			clock-output-names = "s2mps11_ap",
+					"s2mps11_cp", "s2mps11_bt";
 		};
-	};
 
-	hsi2c_4: i2c@12CA0000 {
-		status = "okay";
-
-		s2mps11_pmic@66 {
-			compatible = "samsung,s2mps11-pmic";
-			reg = <0x66>;
-			s2mps11,buck2-ramp-delay = <12>;
-			s2mps11,buck34-ramp-delay = <12>;
-			s2mps11,buck16-ramp-delay = <12>;
-			s2mps11,buck6-ramp-enable = <1>;
-			s2mps11,buck2-ramp-enable = <1>;
-			s2mps11,buck3-ramp-enable = <1>;
-			s2mps11,buck4-ramp-enable = <1>;
-
-			s2mps11_osc: clocks {
-				#clock-cells = <1>;
-				clock-output-names = "s2mps11_ap",
-						"s2mps11_cp", "s2mps11_bt";
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "vdd_ldo1";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "vdd_ldo3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo5_reg: LDO5 {
+				regulator-name = "vdd_ldo5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "vdd_ldo6";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			ldo7_reg: LDO7 {
+				regulator-name = "vdd_ldo7";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo8_reg: LDO8 {
+				regulator-name = "vdd_ldo8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "vdd_ldo9";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "vdd_ldo10";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo11_reg: LDO11 {
+				regulator-name = "vdd_ldo11";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			ldo12_reg: LDO12 {
+				regulator-name = "vdd_ldo12";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
 			};
 
-			regulators {
-				ldo1_reg: LDO1 {
-					regulator-name = "vdd_ldo1";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
-					regulator-always-on;
-				};
-
-				ldo3_reg: LDO3 {
-					regulator-name = "vdd_ldo3";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo5_reg: LDO5 {
-					regulator-name = "vdd_ldo5";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo6_reg: LDO6 {
-					regulator-name = "vdd_ldo6";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
-					regulator-always-on;
-				};
-
-				ldo7_reg: LDO7 {
-					regulator-name = "vdd_ldo7";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo8_reg: LDO8 {
-					regulator-name = "vdd_ldo8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo9_reg: LDO9 {
-					regulator-name = "vdd_ldo9";
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					regulator-always-on;
-				};
-
-				ldo10_reg: LDO10 {
-					regulator-name = "vdd_ldo10";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo11_reg: LDO11 {
-					regulator-name = "vdd_ldo11";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
-					regulator-always-on;
-				};
-
-				ldo12_reg: LDO12 {
-					regulator-name = "vdd_ldo12";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo13_reg: LDO13 {
-					regulator-name = "vdd_ldo13";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					regulator-always-on;
-				};
-
-				ldo15_reg: LDO15 {
-					regulator-name = "vdd_ldo15";
-					regulator-min-microvolt = <3100000>;
-					regulator-max-microvolt = <3100000>;
-					regulator-always-on;
-				};
-
-				ldo16_reg: LDO16 {
-					regulator-name = "vdd_ldo16";
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					regulator-always-on;
-				};
-
-				ldo17_reg: LDO17 {
-					regulator-name = "tsp_avdd";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-always-on;
-				};
-
-				ldo19_reg: LDO19 {
-					regulator-name = "vdd_sd";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					regulator-always-on;
-				};
-
-				ldo24_reg: LDO24 {
-					regulator-name = "tsp_io";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					regulator-always-on;
-				};
-
-				buck1_reg: BUCK1 {
-					regulator-name = "vdd_mif";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1300000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck2_reg: BUCK2 {
-					regulator-name = "vdd_arm";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1500000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck3_reg: BUCK3 {
-					regulator-name = "vdd_int";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1400000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck4_reg: BUCK4 {
-					regulator-name = "vdd_g3d";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1400000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck5_reg: BUCK5 {
-					regulator-name = "vdd_mem";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1400000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck6_reg: BUCK6 {
-					regulator-name = "vdd_kfc";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1500000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck7_reg: BUCK7 {
-					regulator-name = "vdd_1.0v_ldo";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1500000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck8_reg: BUCK8 {
-					regulator-name = "vdd_1.8v_ldo";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1500000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck9_reg: BUCK9 {
-					regulator-name = "vdd_2.8v_ldo";
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3750000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck10_reg: BUCK10 {
-					regulator-name = "vdd_vmem";
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
+			ldo13_reg: LDO13 {
+				regulator-name = "vdd_ldo13";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+			};
+
+			ldo15_reg: LDO15 {
+				regulator-name = "vdd_ldo15";
+				regulator-min-microvolt = <3100000>;
+				regulator-max-microvolt = <3100000>;
+				regulator-always-on;
+			};
+
+			ldo16_reg: LDO16 {
+				regulator-name = "vdd_ldo16";
+				regulator-min-microvolt = <2200000>;
+				regulator-max-microvolt = <2200000>;
+				regulator-always-on;
+			};
+
+			ldo17_reg: LDO17 {
+				regulator-name = "tsp_avdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			ldo19_reg: LDO19 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+			};
+
+			ldo24_reg: LDO24 {
+				regulator-name = "tsp_io";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "vdd_mif";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "vdd_int";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "vdd_g3d";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "vdd_mem";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "vdd_kfc";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck7_reg: BUCK7 {
+				regulator-name = "vdd_1.0v_ldo";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck8_reg: BUCK8 {
+				regulator-name = "vdd_1.8v_ldo";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck9_reg: BUCK9 {
+				regulator-name = "vdd_2.8v_ldo";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3750000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck10_reg: BUCK10 {
+				regulator-name = "vdd_vmem";
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <2850000>;
+				regulator-always-on;
+				regulator-boot-on;
 			};
 		};
 	};
 };
+
+&i2c_2 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <66000>;
+	status = "okay";
+
+	hdmiddc@50 {
+		compatible = "samsung,exynos4210-hdmiddc";
+		reg = <0x50>;
+	};
+};
+
+&mfc {
+	samsung,mfc-r = <0x43000000 0x800000>;
+	samsung,mfc-l = <0x51000000 0x800000>;
+};
+
+&mmc_0 {
+	status = "okay";
+	broken-cd;
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	samsung,dw-mshc-hs400-timing = <0 2>;
+	samsung,read-strobe-delay = <90>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8
+		     &sd0_rclk>;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+};
+
+&mmc_2 {
+	status = "okay";
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+	bus-width = <4>;
+	cap-sd-highspeed;
+};
+
+&pinctrl_0 {
+	hdmi_hpd_irq: hdmi-hpd-irq {
+		samsung,pins = "gpx3-7";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <1>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&pinctrl_2 {
+	usb300_vbus_en: usb300-vbus-en {
+		samsung,pins = "gpg0-5";
+		samsung,pin-function = <1>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	usb301_vbus_en: usb301-vbus-en {
+		samsung,pins = "gpg1-4";
+		samsung,pin-function = <1>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&usbdrd_phy0 {
+	vbus-supply = <&usb300_vbus_reg>;
+};
+
+&usbdrd_phy1 {
+	vbus-supply = <&usb301_vbus_reg>;
+};
-- 
2.1.4

[PATCH v4 7/8] ARM: dts: Use labels for overriding nodes in exynos5440 boards

[Krzysztof Kozlowski]

Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
 arch/arm/boot/dts/exynos5440-sd5v1.dts    | 10 ++--
 arch/arm/boot/dts/exynos5440-ssdk5440.dts | 85 +++++++++++++++----------------
 2 files changed, 47 insertions(+), 48 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5440-sd5v1.dts b/arch/arm/boot/dts/exynos5440-sd5v1.dts
index 268609a42b2c..a98501bab6fc 100644
--- a/arch/arm/boot/dts/exynos5440-sd5v1.dts
+++ b/arch/arm/boot/dts/exynos5440-sd5v1.dts
@@ -27,13 +27,13 @@
 		};
 	};
 
-	gmac: ethernet@00230000 {
-		fixed_phy;
-		phy_addr = <1>;
-	};
-
 	spi {
 		status = "disabled";
 	};
 
 };
+
+&gmac {
+	fixed_phy;
+	phy_addr = <1>;
+};
diff --git a/arch/arm/boot/dts/exynos5440-ssdk5440.dts b/arch/arm/boot/dts/exynos5440-ssdk5440.dts
index ff55dac6e219..e4443f4e6572 100644
--- a/arch/arm/boot/dts/exynos5440-ssdk5440.dts
+++ b/arch/arm/boot/dts/exynos5440-ssdk5440.dts
@@ -20,59 +20,58 @@
 		bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel earlyprintk no_console_suspend mem=2048M@0x80000000 mem=6144M@0x100000000 console=ttySAC0,115200";
 	};
 
-	spi_0: spi@D0000 {
-
-		flash: w25q128@0 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "winbond,w25q128";
-			spi-max-frequency = <15625000>;
-			reg = <0>;
-			controller-data {
-				samsung,spi-feedback-delay = <0>;
-			};
+	fixed-rate-clocks {
+		xtal {
+			compatible = "samsung,clock-xtal";
+			clock-frequency = <50000000>;
+		};
+	};
+};
 
-			partition@00000 {
-				label = "BootLoader";
-				reg = <0x60000 0x80000>;
-				read-only;
-			};
+&pcie_0 {
+	reset-gpio = <&pin_ctrl 5 0>;
+	status = "okay";
+};
 
-			partition@e0000 {
-				label = "Recovery-Kernel";
-				reg = <0xe0000 0x300000>;
-				read-only;
-			};
+&pcie_1 {
+	reset-gpio = <&pin_ctrl 22 0>;
+	status = "okay";
+};
 
-			partition@3e0000 {
-				label = "CRAM-FS";
-				reg = <0x3e0000 0x700000>;
-				read-only;
-			};
+&spi_0 {
+	flash: w25q128@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q128";
+		spi-max-frequency = <15625000>;
+		reg = <0>;
+		controller-data {
+			samsung,spi-feedback-delay = <0>;
+		};
 
-			partition@ae0000 {
-				label = "User-Data";
-				reg = <0xae0000 0x520000>;
-			};
+		partition@00000 {
+			label = "BootLoader";
+			reg = <0x60000 0x80000>;
+			read-only;
+		};
 
+		partition@e0000 {
+			label = "Recovery-Kernel";
+			reg = <0xe0000 0x300000>;
+			read-only;
 		};
 
-	};
+		partition@3e0000 {
+			label = "CRAM-FS";
+			reg = <0x3e0000 0x700000>;
+			read-only;
+		};
 
-	fixed-rate-clocks {
-		xtal {
-			compatible = "samsung,clock-xtal";
-			clock-frequency = <50000000>;
+		partition@ae0000 {
+			label = "User-Data";
+			reg = <0xae0000 0x520000>;
 		};
-	};
 
-	pcie@290000 {
-		reset-gpio = <&pin_ctrl 5 0>;
-		status = "okay";
 	};
 
-	pcie@2a0000 {
-		reset-gpio = <&pin_ctrl 22 0>;
-		status = "okay";
-	};
 };
-- 
2.1.4

[PATCH v4 8/8] ARM: dts: Use labels for overriding nodes in exynos5422-odroidxu3

[Krzysztof Kozlowski]

Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
 arch/arm/boot/dts/exynos5422-odroidxu3.dts | 568 ++++++++++++++---------------
 1 file changed, 284 insertions(+), 284 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3.dts b/arch/arm/boot/dts/exynos5422-odroidxu3.dts
index 6403757011ba..f3f753183f48 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts
@@ -28,10 +28,6 @@
 		linux,stdout-path = &serial_2;
 	};
 
-	fimd@14400000 {
-		status = "okay";
-	};
-
 	firmware@02073000 {
 		compatible = "samsung,secure-firmware";
 		reg = <0x02073000 0x1000>;
@@ -44,229 +40,6 @@
 		};
 	};
 
-	hsi2c_4: i2c@12CA0000 {
-		status = "okay";
-
-		s2mps11_pmic@66 {
-			compatible = "samsung,s2mps11-pmic";
-			reg = <0x66>;
-			s2mps11,buck2-ramp-delay = <12>;
-			s2mps11,buck34-ramp-delay = <12>;
-			s2mps11,buck16-ramp-delay = <12>;
-			s2mps11,buck6-ramp-enable = <1>;
-			s2mps11,buck2-ramp-enable = <1>;
-			s2mps11,buck3-ramp-enable = <1>;
-			s2mps11,buck4-ramp-enable = <1>;
-
-			s2mps11_osc: clocks {
-				#clock-cells = <1>;
-				clock-output-names = "s2mps11_ap",
-						"s2mps11_cp", "s2mps11_bt";
-			};
-
-			regulators {
-				ldo1_reg: LDO1 {
-					regulator-name = "vdd_ldo1";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
-					regulator-always-on;
-				};
-
-				ldo3_reg: LDO3 {
-					regulator-name = "vdd_ldo3";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo5_reg: LDO5 {
-					regulator-name = "vdd_ldo5";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo6_reg: LDO6 {
-					regulator-name = "vdd_ldo6";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
-					regulator-always-on;
-				};
-
-				ldo7_reg: LDO7 {
-					regulator-name = "vdd_ldo7";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo8_reg: LDO8 {
-					regulator-name = "vdd_ldo8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo9_reg: LDO9 {
-					regulator-name = "vdd_ldo9";
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					regulator-always-on;
-				};
-
-				ldo10_reg: LDO10 {
-					regulator-name = "vdd_ldo10";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo11_reg: LDO11 {
-					regulator-name = "vdd_ldo11";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
-					regulator-always-on;
-				};
-
-				ldo12_reg: LDO12 {
-					regulator-name = "vdd_ldo12";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				ldo13_reg: LDO13 {
-					regulator-name = "vdd_ldo13";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					regulator-always-on;
-				};
-
-				ldo15_reg: LDO15 {
-					regulator-name = "vdd_ldo15";
-					regulator-min-microvolt = <3100000>;
-					regulator-max-microvolt = <3100000>;
-					regulator-always-on;
-				};
-
-				ldo16_reg: LDO16 {
-					regulator-name = "vdd_ldo16";
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					regulator-always-on;
-				};
-
-				ldo17_reg: LDO17 {
-					regulator-name = "tsp_avdd";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-always-on;
-				};
-
-				ldo19_reg: LDO19 {
-					regulator-name = "vdd_sd";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					regulator-always-on;
-				};
-
-				ldo24_reg: LDO24 {
-					regulator-name = "tsp_io";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					regulator-always-on;
-				};
-
-				ldo26_reg: LDO26 {
-					regulator-name = "vdd_ldo26";
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					regulator-always-on;
-				};
-
-				buck1_reg: BUCK1 {
-					regulator-name = "vdd_mif";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1300000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck2_reg: BUCK2 {
-					regulator-name = "vdd_arm";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1500000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck3_reg: BUCK3 {
-					regulator-name = "vdd_int";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1400000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck4_reg: BUCK4 {
-					regulator-name = "vdd_g3d";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1400000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck5_reg: BUCK5 {
-					regulator-name = "vdd_mem";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1400000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck6_reg: BUCK6 {
-					regulator-name = "vdd_kfc";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1500000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck7_reg: BUCK7 {
-					regulator-name = "vdd_1.0v_ldo";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1500000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck8_reg: BUCK8 {
-					regulator-name = "vdd_1.8v_ldo";
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1500000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck9_reg: BUCK9 {
-					regulator-name = "vdd_2.8v_ldo";
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3750000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				buck10_reg: BUCK10 {
-					regulator-name = "vdd_vmem";
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-			};
-		};
-	};
-
 	emmc_pwrseq: pwrseq {
 		pinctrl-0 = <&emmc_nrst_pin>;
 		pinctrl-names = "default";
@@ -274,17 +47,6 @@
 		reset-gpios = <&gpd1 0 1>;
 	};
 
-	i2c_2: i2c@12C80000 {
-		samsung,i2c-sda-delay = <100>;
-		samsung,i2c-max-bus-freq = <66000>;
-		status = "okay";
-
-		hdmiddc@50 {
-			compatible = "samsung,exynos4210-hdmiddc";
-			reg = <0x50>;
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 		heartbeat {
@@ -351,6 +113,245 @@
 			<19200000>;
 };
 
+&fimd {
+	status = "okay";
+};
+
+
+&hdmi {
+	status = "okay";
+	hpd-gpio = <&gpx3 7 0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_hpd_irq>;
+
+	vdd_osc-supply = <&ldo7_reg>;
+	vdd_pll-supply = <&ldo6_reg>;
+	vdd-supply = <&ldo6_reg>;
+};
+
+&hsi2c_4 {
+	status = "okay";
+
+	s2mps11_pmic@66 {
+		compatible = "samsung,s2mps11-pmic";
+		reg = <0x66>;
+		s2mps11,buck2-ramp-delay = <12>;
+		s2mps11,buck34-ramp-delay = <12>;
+		s2mps11,buck16-ramp-delay = <12>;
+		s2mps11,buck6-ramp-enable = <1>;
+		s2mps11,buck2-ramp-enable = <1>;
+		s2mps11,buck3-ramp-enable = <1>;
+		s2mps11,buck4-ramp-enable = <1>;
+
+		s2mps11_osc: clocks {
+			#clock-cells = <1>;
+			clock-output-names = "s2mps11_ap",
+					"s2mps11_cp", "s2mps11_bt";
+		};
+
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "vdd_ldo1";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "vdd_ldo3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo5_reg: LDO5 {
+				regulator-name = "vdd_ldo5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "vdd_ldo6";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			ldo7_reg: LDO7 {
+				regulator-name = "vdd_ldo7";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo8_reg: LDO8 {
+				regulator-name = "vdd_ldo8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "vdd_ldo9";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "vdd_ldo10";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo11_reg: LDO11 {
+				regulator-name = "vdd_ldo11";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			ldo12_reg: LDO12 {
+				regulator-name = "vdd_ldo12";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo13_reg: LDO13 {
+				regulator-name = "vdd_ldo13";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+			};
+
+			ldo15_reg: LDO15 {
+				regulator-name = "vdd_ldo15";
+				regulator-min-microvolt = <3100000>;
+				regulator-max-microvolt = <3100000>;
+				regulator-always-on;
+			};
+
+			ldo16_reg: LDO16 {
+				regulator-name = "vdd_ldo16";
+				regulator-min-microvolt = <2200000>;
+				regulator-max-microvolt = <2200000>;
+				regulator-always-on;
+			};
+
+			ldo17_reg: LDO17 {
+				regulator-name = "tsp_avdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			ldo19_reg: LDO19 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+			};
+
+			ldo24_reg: LDO24 {
+				regulator-name = "tsp_io";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+			};
+
+			ldo26_reg: LDO26 {
+				regulator-name = "vdd_ldo26";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "vdd_mif";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "vdd_int";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "vdd_g3d";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "vdd_mem";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "vdd_kfc";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck7_reg: BUCK7 {
+				regulator-name = "vdd_1.0v_ldo";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck8_reg: BUCK8 {
+				regulator-name = "vdd_1.8v_ldo";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck9_reg: BUCK9 {
+				regulator-name = "vdd_2.8v_ldo";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3750000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck10_reg: BUCK10 {
+				regulator-name = "vdd_vmem";
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <2850000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
 &hsi2c_5 {
 	status = "okay";
 	max98090: max98090@10 {
@@ -364,19 +365,50 @@
 	};
 };
 
-&i2s0 {
+&i2c_0 {
 	status = "okay";
+	/* A15 cluster: VDD_ARM */
+	ina231@40 {
+		compatible = "ti,ina231";
+		reg = <0x40>;
+		shunt-resistor = <10000>;
+	};
+
+	/* memory: VDD_MEM */
+	ina231@41 {
+		compatible = "ti,ina231";
+		reg = <0x41>;
+		shunt-resistor = <10000>;
+	};
+
+	/* GPU: VDD_G3D */
+	ina231@44 {
+		compatible = "ti,ina231";
+		reg = <0x44>;
+		shunt-resistor = <10000>;
+	};
+
+	/* A7 cluster: VDD_KFC */
+	ina231@45 {
+		compatible = "ti,ina231";
+		reg = <0x45>;
+		shunt-resistor = <10000>;
+	};
 };
 
-&hdmi {
+&i2c_2 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <66000>;
 	status = "okay";
-	hpd-gpio = <&gpx3 7 0>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&hdmi_hpd_irq>;
 
-	vdd_osc-supply = <&ldo7_reg>;
-	vdd_pll-supply = <&ldo6_reg>;
-	vdd-supply = <&ldo6_reg>;
+	hdmiddc@50 {
+		compatible = "samsung,exynos4210-hdmiddc";
+		reg = <0x50>;
+	};
+};
+
+&i2s0 {
+	status = "okay";
 };
 
 &mfc {
@@ -432,6 +464,12 @@
 	};
 };
 
+&rtc {
+	status = "okay";
+	clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
+	clock-names = "rtc", "rtc_src";
+};
+
 &usbdrd_dwc3_0 {
 	dr_mode = "host";
 };
@@ -439,41 +477,3 @@
 &usbdrd_dwc3_1 {
 	dr_mode = "otg";
 };
-
-&i2c_0 {
-	status = "okay";
-
-	/* A15 cluster: VDD_ARM */
-	ina231@40 {
-		compatible = "ti,ina231";
-		reg = <0x40>;
-		shunt-resistor = <10000>;
-	};
-
-	/* memory: VDD_MEM */
-	ina231@41 {
-		compatible = "ti,ina231";
-		reg = <0x41>;
-		shunt-resistor = <10000>;
-	};
-
-	/* GPU: VDD_G3D */
-	ina231@44 {
-		compatible = "ti,ina231";
-		reg = <0x44>;
-		shunt-resistor = <10000>;
-	};
-
-	/* A7 cluster: VDD_KFC */
-	ina231@45 {
-		compatible = "ti,ina231";
-		reg = <0x45>;
-		shunt-resistor = <10000>;
-	};
-};
-
-&rtc {
-	status = "okay";
-	clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
-	clock-names = "rtc", "rtc_src";
-};
-- 
2.1.4

Re: [PATCH v4 0/8] ARM: dts: exynos5: labels for overriding nodes

[Kukjin Kim]

On 05/17/15 17:26, Krzysztof Kozlowski wrote:
> Hi,
> 
> 
> Changes since v3
> ================
> 1. Rebased on current Kukjin's for-next branch:
>    v4.1-rc3-34-gfcfae6b049cf
> 
> Changes since v2
> ================
> 1. New patch 8/8: ARM: dts: Use labels for overriding nodes
>    in exynos5422-odroidxu3
> 2. To avoid conflicts rebased on my "for-next" branch of
>    https://github.com/krzk/linux
>    The branch above contains some patches for Exynos5 boards
>    applied from LKML.
> 
> Changes since v1
> ================
> 1. Re-phrased the description (phandle->label). Suggested by Arnd.
> 
> 
> Description
> ===========
> The label-based notation reduces possible mistakes when overriding
> nodes by child DTSI and board files and reduces duplication
> of addresses.
> 
> The patchset refactors Exynos5 boards to use labels for overriding nodes.
> 
> Tested by comparison of decompiled DTB for each commit.
> 
Same, will sort out.

Thanks,
Kukjin