[PATCH v11] crypto: Add Allwinner Security System crypto accelerator

[PATCH v11] crypto: Add Allwinner Security System crypto accelerator

[LABBE Corentin]

Hello

This is the driver for the Security System included in Allwinner SoC A20.
The Security System (SS for short) is a hardware cryptographic accelerator that
support AES/MD5/SHA1/DES/3DES/PRNG algorithms.
It could be found on others Allwinner SoC: 
- A10, A10s, A13, A31 and A33 manual give the same datasheet for SS than A20
- A23 speak about a security system but without precisions
- A80 and A83T datasheet speak about a security system with more functions
  (SHA224/SHA256/RSA/CRC), they will be supported in a separate driver.

This driver currently supports:
- MD5 and SHA1 hash algorithms
- AES block cipher in CBC/ECB mode with 128/196/256bits keys.
- DES and 3DES block cipher in CBC/ECB mode
The driver exposes all those algorithms through the kernel cryptographic API.

The driver support only CPU driven (aka poll mode) transfer mode,
since the DMA engine of the A20 does not have a mainline driver yet.

For the moment the driver is fully synchronous.
A patch exists for making the driver asynchronous at the costs of badly decreasing performance.
It will be re-introduced later when DMA will be supported.

Changes since v10
- fix checkpatch --strict issues (except for BIT where it is volontary)
- lots of spelling fix
- add mode to algt
- import/export now initialize correctly op
- replace some dev_err with dev_err_ratelimited

Changes since v9
- use spin_lock_bh instead of spin_lock_irqx
- use sg_miter always with SG_MITER_ATOMIC flag
- rework the hash update functions
- the DES/3DES/AES now uses two functions one for all case and one for SG with
 size not multiple of 4 and so remove the fallback for DES/3DES
- add A10 support, tested by Matthieu CERDA
- fix export/import functions
- do not use any _relaxed read/write
- write IV at end of cipher functions

Changes since v8
- use sg_miter in cipher functions, this clean all kmap stuff (thanks to bbrezillon)
- use GIC in dt interupts
- rename all references (files/dtcompatible) from sunxi to sun4i in prevision of futur A80/A83 driver

Changes since v7
- Add ECB block mode
- split the sunxi_ss_cipher_init in two
- remove sunxi_ss_cipher_encrypt/sunxi_ss_cipher_decrypt
- use now sunxi_ss_block_method_encrypt and sunxi_ss_block_method_decrypt
- Add weak DES key test needed by ECB tests

Changes since v6:
- Use alphabetic ordering for new sections in MAINTAINERS
- Clean remaining PRNG driver header

Changes since v5:
- Hash functions now keep partial hash states in sunxi_ss structures
- Use of spinlock instead of mutex
- Remove the static sunxi_ss structures by using container of
- Add export/import functions
- replace lots of writel by writesl
- replace lots of readl by readsl

Changes since v4:
- Rework all mutex path
- Use ahash_request_ctx() in hash functions
- Major rework of hash functions for solving mutex problems
- Split sunxi_req_ctx in two since ciphers now use struct sunxi_tfm_ctx
- Hash functions now test FIFO space register

Changes since v3:
- Remove all algorithms options from Kconfig, so now only one module is used
- Add the sunxi_ss_cipher function to unify mode calculation
- Remove the sunxi_cipher_exit empty function
- Add some missing mutex_unlock()
- Drop PRNG support, I wait for more comment on its results before re-enabling it.

Changes since v2:
- Fix Makefile and Kconfig for static kernel.

Changes since v1:
- annotate ss->base as __iomem
- regroup all mutex in the ss_ctx structure
- splited driver in 7 modules (core md5 sha1 aes des 3des prng) in sunxi-ss directory
- use dev_exit_p() for .remove
- added missing CRYPTO_BLKCIPHER dep in Kconfig
- use ahash instead of shash
- use ablkcipher instead of blkcipher
- use crypto_rng_ctx instead of crypto_tfm_ctx
- set seed as an u32
- drop useless comment decoration
- drop useless debug
- ss_ctx is now a static pointer and whole structure being allocated
- fix the platform_get_resource/devm_ioremap_resource pattern
- invert getting die id and configuring clock
- set clock value as a const unsigned long
- add MODULE_ALIAS
- use define names more consistency (SS_xxx)
- fix PRNG errors
- respell SS to Security System in DT documentation

[PATCH v11 1/5] ARM: sun4i: dt: Add Security System to A10 SoC DTS

[LABBE Corentin]

The Security System is a hardware cryptographic accelerator that support
AES/MD5/SHA1/DES/3DES/PRNG algorithms.
It could be found on many Allwinner SoC.

This patch enable the Security System on the Allwinner A10 SoC Device-tree.

Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
---
 arch/arm/boot/dts/sun4i-a10.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/sun4i-a10.dtsi
index 61c03d1..551e3d1 100644
--- a/arch/arm/boot/dts/sun4i-a10.dtsi
+++ b/arch/arm/boot/dts/sun4i-a10.dtsi
@@ -643,6 +643,14 @@
 			status = "disabled";
 		};
 
+		crypto: crypto-engine@01c15000 {
+			compatible = "allwinner,sun4i-a10-crypto";
+			reg = <0x01c15000 0x1000>;
+			interrupts = <86>;
+			clocks = <&ahb_gates 5>, <&ss_clk>;
+			clock-names = "ahb", "mod";
+		};
+
 		spi2: spi@01c17000 {
 			compatible = "allwinner,sun4i-a10-spi";
 			reg = <0x01c17000 0x1000>;
-- 
2.3.6

[PATCH v11 2/5] ARM: sun7i: dt: Add Security System to A20 SoC DTS

[LABBE Corentin]

The Security System is a hardware cryptographic accelerator that support
AES/MD5/SHA1/DES/3DES/PRNG algorithms.
It could be found on many Allwinner SoC.

This patch enable the Security System on the Allwinner A20 SoC Device-tree.

Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
---
 arch/arm/boot/dts/sun7i-a20.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
index 6a63f30..ba049d3 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++ b/arch/arm/boot/dts/sun7i-a20.dtsi
@@ -731,6 +731,14 @@
 			status = "disabled";
 		};
 
+		crypto: crypto-engine@01c15000 {
+			compatible = "allwinner,sun4i-a10-crypto";
+			reg = <0x01c15000 0x1000>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ahb_gates 5>, <&ss_clk>;
+			clock-names = "ahb", "mod";
+		};
+
 		spi2: spi@01c17000 {
 			compatible = "allwinner,sun4i-a10-spi";
 			reg = <0x01c17000 0x1000>;
-- 
2.3.6

[PATCH v11 3/5] ARM: sun4i: dt: Add DT bindings documentation for SUN4I Security System

[LABBE Corentin]

This patch adds documentation for Device-Tree bindings for the
Security System cryptographic accelerator driver.

Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
---
 Documentation/devicetree/bindings/crypto/sun4i-ss.txt | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/crypto/sun4i-ss.txt

diff --git a/Documentation/devicetree/bindings/crypto/sun4i-ss.txt b/Documentation/devicetree/bindings/crypto/sun4i-ss.txt
new file mode 100644
index 0000000..1e02d17
--- /dev/null
+++ b/Documentation/devicetree/bindings/crypto/sun4i-ss.txt
@@ -0,0 +1,19 @@
+* Allwinner Security System found on A20 SoC
+
+Required properties:
+- compatible : Should be "allwinner,sun4i-a10-crypto".
+- reg: Should contain the Security System register location and length.
+- interrupts: Should contain the IRQ line for the Security System.
+- clocks : List of clock specifiers, corresponding to ahb and ss.
+- clock-names : Name of the functional clock, should be
+	* "ahb" : AHB gating clock
+	* "mod" : SS controller clock
+
+Example:
+	crypto: crypto-engine@01c15000 {
+		compatible = "allwinner,sun4i-a10-crypto";
+		reg = <0x01c15000 0x1000>;
+		interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&ahb_gates 5>, <&ss_clk>;
+		clock-names = "ahb", "mod";
+	};
-- 
2.3.6

[PATCH v11 4/5] crypto: Add Allwinner Security System crypto accelerator

[LABBE Corentin]

Add support for the Security System included in Allwinner SoC A20.
The Security System is a hardware cryptographic accelerator that support:
- MD5 and SHA1 hash algorithms
- AES block cipher in CBC/ECB mode with 128/196/256bits keys.
- DES and 3DES block cipher in CBC/ECB mode

Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
---
 drivers/crypto/Kconfig                    |  17 +
 drivers/crypto/Makefile                   |   1 +
 drivers/crypto/sunxi-ss/Makefile          |   2 +
 drivers/crypto/sunxi-ss/sun4i-ss-cipher.c | 542 ++++++++++++++++++++++++++++++
 drivers/crypto/sunxi-ss/sun4i-ss-core.c   | 403 ++++++++++++++++++++++
 drivers/crypto/sunxi-ss/sun4i-ss-hash.c   | 492 +++++++++++++++++++++++++++
 drivers/crypto/sunxi-ss/sun4i-ss.h        | 199 +++++++++++
 7 files changed, 1656 insertions(+)
 create mode 100644 drivers/crypto/sunxi-ss/Makefile
 create mode 100644 drivers/crypto/sunxi-ss/sun4i-ss-cipher.c
 create mode 100644 drivers/crypto/sunxi-ss/sun4i-ss-core.c
 create mode 100644 drivers/crypto/sunxi-ss/sun4i-ss-hash.c
 create mode 100644 drivers/crypto/sunxi-ss/sun4i-ss.h

diff --git a/drivers/crypto/Kconfig b/drivers/crypto/Kconfig
index 4044125..07bc7aa 100644
--- a/drivers/crypto/Kconfig
+++ b/drivers/crypto/Kconfig
@@ -480,4 +480,21 @@ config CRYPTO_DEV_IMGTEC_HASH
 	  hardware hash accelerator. Supporting MD5/SHA1/SHA224/SHA256
 	  hashing algorithms.
 
+config CRYPTO_DEV_SUN4I_SS
+	tristate "Support for Allwinner Security System cryptographic accelerator"
+	depends on ARCH_SUNXI
+	select CRYPTO_MD5
+	select CRYPTO_SHA1
+	select CRYPTO_AES
+	select CRYPTO_DES
+	select CRYPTO_BLKCIPHER
+	help
+	  Some Allwinner SoC have a crypto accelerator named
+	  Security System. Select this if you want to use it.
+	  The Security System handle AES/DES/3DES ciphers in CBC mode
+	  and SHA1 and MD5 hash algorithms.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called sun4i-ss.
+
 endif # CRYPTO_HW
diff --git a/drivers/crypto/Makefile b/drivers/crypto/Makefile
index e35c07a..c3ced6f 100644
--- a/drivers/crypto/Makefile
+++ b/drivers/crypto/Makefile
@@ -28,3 +28,4 @@ obj-$(CONFIG_CRYPTO_DEV_UX500) += ux500/
 obj-$(CONFIG_CRYPTO_DEV_QAT) += qat/
 obj-$(CONFIG_CRYPTO_DEV_QCE) += qce/
 obj-$(CONFIG_CRYPTO_DEV_VMX) += vmx/
+obj-$(CONFIG_CRYPTO_DEV_SUN4I_SS) += sunxi-ss/
diff --git a/drivers/crypto/sunxi-ss/Makefile b/drivers/crypto/sunxi-ss/Makefile
new file mode 100644
index 0000000..8f4c7a2
--- /dev/null
+++ b/drivers/crypto/sunxi-ss/Makefile
@@ -0,0 +1,2 @@
+obj-$(CONFIG_CRYPTO_DEV_SUN4I_SS) += sun4i-ss.o
+sun4i-ss-y += sun4i-ss-core.o sun4i-ss-hash.o sun4i-ss-cipher.o
diff --git a/drivers/crypto/sunxi-ss/sun4i-ss-cipher.c b/drivers/crypto/sunxi-ss/sun4i-ss-cipher.c
new file mode 100644
index 0000000..e070c31
--- /dev/null
+++ b/drivers/crypto/sunxi-ss/sun4i-ss-cipher.c
@@ -0,0 +1,542 @@
+/*
+ * sun4i-ss-cipher.c - hardware cryptographic accelerator for Allwinner A20 SoC
+ *
+ * Copyright (C) 2013-2015 Corentin LABBE <clabbe.montjoie@gmail.com>
+ *
+ * This file add support for AES cipher with 128,192,256 bits
+ * keysize in CBC and ECB mode.
+ * Add support also for DES and 3DES in CBC and ECB mode.
+ *
+ * You could find the datasheet in Documentation/arm/sunxi/README
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include "sun4i-ss.h"
+
+static int sun4i_ss_opti_poll(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_ss_ctx *ss = op->ss;
+	unsigned int ivsize = crypto_ablkcipher_ivsize(tfm);
+	struct sun4i_cipher_req_ctx *ctx = ablkcipher_request_ctx(areq);
+	u32 mode = ctx->mode;
+	/* when activating SS, the default FIFO space is SS_RX_DEFAULT(32) */
+	u32 rx_cnt = SS_RX_DEFAULT;
+	u32 tx_cnt = 0;
+	u32 spaces;
+	u32 v;
+	int i, err = 0;
+	unsigned int ileft = areq->nbytes;
+	unsigned int oleft = areq->nbytes;
+	unsigned int todo;
+	struct sg_mapping_iter mi, mo;
+	unsigned int oi, oo; /* offset for in and out */
+
+	if (areq->nbytes == 0)
+		return 0;
+
+	if (!areq->info) {
+		dev_err_ratelimited(ss->dev, "ERROR: Empty IV\n");
+		return -EINVAL;
+	}
+
+	if (!areq->src || !areq->dst) {
+		dev_err_ratelimited(ss->dev, "ERROR: Some SGs are NULL\n");
+		return -EINVAL;
+	}
+
+	spin_lock_bh(&ss->slock);
+
+	for (i = 0; i < op->keylen; i += 4)
+		writel(*(op->key + i / 4), ss->base + SS_KEY0 + i);
+
+	if (areq->info) {
+		for (i = 0; i < 4 && i < ivsize / 4; i++) {
+			v = *(u32 *)(areq->info + i * 4);
+			writel(v, ss->base + SS_IV0 + i * 4);
+		}
+	}
+	writel(mode, ss->base + SS_CTL);
+
+	sg_miter_start(&mi, areq->src, sg_nents(areq->src),
+		       SG_MITER_FROM_SG | SG_MITER_ATOMIC);
+	sg_miter_start(&mo, areq->dst, sg_nents(areq->dst),
+		       SG_MITER_TO_SG | SG_MITER_ATOMIC);
+	sg_miter_next(&mi);
+	sg_miter_next(&mo);
+	if (!mi.addr || !mo.addr) {
+		dev_err_ratelimited(ss->dev, "ERROR: sg_miter return null\n");
+		err = -EINVAL;
+		goto release_ss;
+	}
+
+	ileft = areq->nbytes / 4;
+	oleft = areq->nbytes / 4;
+	oi = 0;
+	oo = 0;
+	do {
+		todo = min3(rx_cnt, ileft, (mi.length - oi) / 4);
+		if (todo > 0) {
+			ileft -= todo;
+			writesl(ss->base + SS_RXFIFO, mi.addr + oi, todo);
+			oi += todo * 4;
+		}
+		if (oi == mi.length) {
+			sg_miter_next(&mi);
+			oi = 0;
+		}
+
+		spaces = readl(ss->base + SS_FCSR);
+		rx_cnt = SS_RXFIFO_SPACES(spaces);
+		tx_cnt = SS_TXFIFO_SPACES(spaces);
+
+		todo = min3(tx_cnt, oleft, (mo.length - oo) / 4);
+		if (todo > 0) {
+			oleft -= todo;
+			readsl(ss->base + SS_TXFIFO, mo.addr + oo, todo);
+			oo += todo * 4;
+		}
+		if (oo == mo.length) {
+			sg_miter_next(&mo);
+			oo = 0;
+		}
+	} while (mo.length > 0);
+
+	if (areq->info) {
+		for (i = 0; i < 4 && i < ivsize / 4; i++) {
+			v = readl(ss->base + SS_IV0 + i * 4);
+			*(u32 *)(areq->info + i * 4) = v;
+		}
+	}
+
+release_ss:
+	sg_miter_stop(&mi);
+	sg_miter_stop(&mo);
+	writel(0, ss->base + SS_CTL);
+	spin_unlock_bh(&ss->slock);
+	return err;
+}
+
+/* Generic function that support SG with size not multiple of 4 */
+static int sun4i_ss_cipher_poll(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_ss_ctx *ss = op->ss;
+	int no_chunk = 1;
+	struct scatterlist *in_sg = areq->src;
+	struct scatterlist *out_sg = areq->dst;
+	unsigned int ivsize = crypto_ablkcipher_ivsize(tfm);
+	struct sun4i_cipher_req_ctx *ctx = ablkcipher_request_ctx(areq);
+	u32 mode = ctx->mode;
+	/* when activating SS, the default FIFO space is SS_RX_DEFAULT(32) */
+	u32 rx_cnt = SS_RX_DEFAULT;
+	u32 tx_cnt = 0;
+	u32 v;
+	u32 spaces;
+	int i, err = 0;
+	unsigned int ileft = areq->nbytes;
+	unsigned int oleft = areq->nbytes;
+	unsigned int todo;
+	struct sg_mapping_iter mi, mo;
+	unsigned int oi, oo;	/* offset for in and out */
+	char buf[4 * SS_RX_MAX];/* buffer for linearize SG src */
+	char bufo[4 * SS_TX_MAX]; /* buffer for linearize SG dst */
+	unsigned int ob = 0;	/* offset in buf */
+	unsigned int obo = 0;	/* offset in bufo*/
+	unsigned int obl = 0;	/* length of data in bufo */
+
+	if (areq->nbytes == 0)
+		return 0;
+
+	if (!areq->info) {
+		dev_err_ratelimited(ss->dev, "ERROR: Empty IV\n");
+		return -EINVAL;
+	}
+
+	if (!areq->src || !areq->dst) {
+		dev_err_ratelimited(ss->dev, "ERROR: Some SGs are NULL\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * if we have only SGs with size multiple of 4,
+	 * we can use the SS optimized function
+	 */
+	while (in_sg && no_chunk == 1) {
+		if ((in_sg->length % 4) != 0)
+			no_chunk = 0;
+		in_sg = sg_next(in_sg);
+	}
+	while (out_sg && no_chunk == 1) {
+		if ((out_sg->length % 4) != 0)
+			no_chunk = 0;
+		out_sg = sg_next(out_sg);
+	}
+
+	if (no_chunk == 1)
+		return sun4i_ss_opti_poll(areq);
+
+	spin_lock_bh(&ss->slock);
+
+	for (i = 0; i < op->keylen; i += 4)
+		writel(*(op->key + i / 4), ss->base + SS_KEY0 + i);
+
+	if (areq->info) {
+		for (i = 0; i < 4 && i < ivsize / 4; i++) {
+			v = *(u32 *)(areq->info + i * 4);
+			writel(v, ss->base + SS_IV0 + i * 4);
+		}
+	}
+	writel(mode, ss->base + SS_CTL);
+
+	sg_miter_start(&mi, areq->src, sg_nents(areq->src),
+		       SG_MITER_FROM_SG | SG_MITER_ATOMIC);
+	sg_miter_start(&mo, areq->dst, sg_nents(areq->dst),
+		       SG_MITER_TO_SG | SG_MITER_ATOMIC);
+	sg_miter_next(&mi);
+	sg_miter_next(&mo);
+	if (!mi.addr || !mo.addr) {
+		dev_err_ratelimited(ss->dev, "ERROR: sg_miter return null\n");
+		err = -EINVAL;
+		goto release_ss;
+	}
+	ileft = areq->nbytes;
+	oleft = areq->nbytes;
+	oi = 0;
+	oo = 0;
+
+	while (oleft > 0) {
+		if (ileft > 0) {
+			/*
+			 * todo is the number of consecutive 4byte word that we
+			 * can read from current SG
+			 */
+			todo = min3(rx_cnt, ileft / 4, (mi.length - oi) / 4);
+			if (todo > 0 && ob == 0) {
+				writesl(ss->base + SS_RXFIFO, mi.addr + oi,
+					todo);
+				ileft -= todo * 4;
+				oi += todo * 4;
+			} else {
+				/*
+				 * not enough consecutive bytes, so we need to
+				 * linearize in buf. todo is in bytes
+				 * After that copy, if we have a multiple of 4
+				 * we need to be able to write all buf in one
+				 * pass, so it is why we min() with rx_cnt
+				 */
+				todo = min3(rx_cnt * 4 - ob, ileft,
+					    mi.length - oi);
+				memcpy(buf + ob, mi.addr + oi, todo);
+				ileft -= todo;
+				oi += todo;
+				ob += todo;
+				if (ob % 4 == 0) {
+					writesl(ss->base + SS_RXFIFO, buf,
+						ob / 4);
+					ob = 0;
+				}
+			}
+			if (oi == mi.length) {
+				sg_miter_next(&mi);
+				oi = 0;
+			}
+		}
+
+		spaces = readl(ss->base + SS_FCSR);
+		rx_cnt = SS_RXFIFO_SPACES(spaces);
+		tx_cnt = SS_TXFIFO_SPACES(spaces);
+		dev_dbg(ss->dev, "%x %u/%u %u/%u cnt=%u %u/%u %u/%u cnt=%u %u %u\n",
+			mode,
+			oi, mi.length, ileft, areq->nbytes, rx_cnt,
+			oo, mo.length, oleft, areq->nbytes, tx_cnt,
+			todo, ob);
+
+		if (tx_cnt == 0)
+			continue;
+		/* todo in 4bytes word */
+		todo = min3(tx_cnt, oleft / 4, (mo.length - oo) / 4);
+		if (todo > 0) {
+			readsl(ss->base + SS_TXFIFO, mo.addr + oo, todo);
+			oleft -= todo * 4;
+			oo += todo * 4;
+			if (oo == mo.length) {
+				sg_miter_next(&mo);
+				oo = 0;
+			}
+		} else {
+			/*
+			 * read obl bytes in bufo, we read at maximum for
+			 * emptying the device
+			 */
+			readsl(ss->base + SS_TXFIFO, bufo, tx_cnt);
+			obl = tx_cnt * 4;
+			obo = 0;
+			do {
+				/*
+				 * how many bytes we can copy ?
+				 * no more than remaining SG size
+				 * no more than remaining buffer
+				 * no need to test against oleft
+				 */
+				todo = min(mo.length - oo, obl - obo);
+				memcpy(mo.addr + oo, bufo + obo, todo);
+				oleft -= todo;
+				obo += todo;
+				oo += todo;
+				if (oo == mo.length) {
+					sg_miter_next(&mo);
+					oo = 0;
+				}
+			} while (obo < obl);
+			/* bufo must be fully used here */
+		}
+	}
+	if (areq->info) {
+		for (i = 0; i < 4 && i < ivsize / 4; i++) {
+			v = readl(ss->base + SS_IV0 + i * 4);
+			*(u32 *)(areq->info + i * 4) = v;
+		}
+	}
+
+release_ss:
+	sg_miter_stop(&mi);
+	sg_miter_stop(&mo);
+	writel(0, ss->base + SS_CTL);
+	spin_unlock_bh(&ss->slock);
+
+	return err;
+}
+
+/* CBC AES */
+int sun4i_ss_cbc_aes_encrypt(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_cipher_req_ctx *rctx = ablkcipher_request_ctx(areq);
+
+	rctx->mode = SS_OP_AES | SS_CBC | SS_ENABLED | SS_ENCRYPTION |
+		op->keymode;
+	return sun4i_ss_cipher_poll(areq);
+}
+
+int sun4i_ss_cbc_aes_decrypt(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_cipher_req_ctx *rctx = ablkcipher_request_ctx(areq);
+
+	rctx->mode = SS_OP_AES | SS_CBC | SS_ENABLED | SS_DECRYPTION |
+		op->keymode;
+	return sun4i_ss_cipher_poll(areq);
+}
+
+/* ECB AES */
+int sun4i_ss_ecb_aes_encrypt(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_cipher_req_ctx *rctx = ablkcipher_request_ctx(areq);
+
+	rctx->mode = SS_OP_AES | SS_ECB | SS_ENABLED | SS_ENCRYPTION |
+		op->keymode;
+	return sun4i_ss_cipher_poll(areq);
+}
+
+int sun4i_ss_ecb_aes_decrypt(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_cipher_req_ctx *rctx = ablkcipher_request_ctx(areq);
+
+	rctx->mode = SS_OP_AES | SS_ECB | SS_ENABLED | SS_DECRYPTION |
+		op->keymode;
+	return sun4i_ss_cipher_poll(areq);
+}
+
+/* CBC DES */
+int sun4i_ss_cbc_des_encrypt(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_cipher_req_ctx *rctx = ablkcipher_request_ctx(areq);
+
+	rctx->mode = SS_OP_DES | SS_CBC | SS_ENABLED | SS_ENCRYPTION |
+		op->keymode;
+	return sun4i_ss_cipher_poll(areq);
+}
+
+int sun4i_ss_cbc_des_decrypt(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_cipher_req_ctx *rctx = ablkcipher_request_ctx(areq);
+
+	rctx->mode = SS_OP_DES | SS_CBC | SS_ENABLED | SS_DECRYPTION |
+		op->keymode;
+	return sun4i_ss_cipher_poll(areq);
+}
+
+/* ECB DES */
+int sun4i_ss_ecb_des_encrypt(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_cipher_req_ctx *rctx = ablkcipher_request_ctx(areq);
+
+	rctx->mode = SS_OP_DES | SS_ECB | SS_ENABLED | SS_ENCRYPTION |
+		op->keymode;
+	return sun4i_ss_cipher_poll(areq);
+}
+
+int sun4i_ss_ecb_des_decrypt(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_cipher_req_ctx *rctx = ablkcipher_request_ctx(areq);
+
+	rctx->mode = SS_OP_DES | SS_ECB | SS_ENABLED | SS_DECRYPTION |
+		op->keymode;
+	return sun4i_ss_cipher_poll(areq);
+}
+
+/* CBC 3DES */
+int sun4i_ss_cbc_des3_encrypt(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_cipher_req_ctx *rctx = ablkcipher_request_ctx(areq);
+
+	rctx->mode = SS_OP_3DES | SS_CBC | SS_ENABLED | SS_ENCRYPTION |
+		op->keymode;
+	return sun4i_ss_cipher_poll(areq);
+}
+
+int sun4i_ss_cbc_des3_decrypt(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_cipher_req_ctx *rctx = ablkcipher_request_ctx(areq);
+
+	rctx->mode = SS_OP_3DES | SS_CBC | SS_ENABLED | SS_DECRYPTION |
+		op->keymode;
+	return sun4i_ss_cipher_poll(areq);
+}
+
+/* ECB 3DES */
+int sun4i_ss_ecb_des3_encrypt(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_cipher_req_ctx *rctx = ablkcipher_request_ctx(areq);
+
+	rctx->mode = SS_OP_3DES | SS_ECB | SS_ENABLED | SS_ENCRYPTION |
+		op->keymode;
+	return sun4i_ss_cipher_poll(areq);
+}
+
+int sun4i_ss_ecb_des3_decrypt(struct ablkcipher_request *areq)
+{
+	struct crypto_ablkcipher *tfm = crypto_ablkcipher_reqtfm(areq);
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_cipher_req_ctx *rctx = ablkcipher_request_ctx(areq);
+
+	rctx->mode = SS_OP_3DES | SS_ECB | SS_ENABLED | SS_DECRYPTION |
+		op->keymode;
+	return sun4i_ss_cipher_poll(areq);
+}
+
+int sun4i_ss_cipher_init(struct crypto_tfm *tfm)
+{
+	struct sun4i_tfm_ctx *op = crypto_tfm_ctx(tfm);
+	struct crypto_alg *alg = tfm->__crt_alg;
+	struct sun4i_ss_alg_template *algt;
+
+	memset(op, 0, sizeof(struct sun4i_tfm_ctx));
+
+	algt = container_of(alg, struct sun4i_ss_alg_template, alg.crypto);
+	op->ss = algt->ss;
+
+	tfm->crt_ablkcipher.reqsize = sizeof(struct sun4i_cipher_req_ctx);
+
+	return 0;
+}
+
+/* check and set the AES key, prepare the mode to be used */
+int sun4i_ss_aes_setkey(struct crypto_ablkcipher *tfm, const u8 *key,
+			unsigned int keylen)
+{
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_ss_ctx *ss = op->ss;
+
+	switch (keylen) {
+	case 128 / 8:
+		op->keymode = SS_AES_128BITS;
+		break;
+	case 192 / 8:
+		op->keymode = SS_AES_192BITS;
+		break;
+	case 256 / 8:
+		op->keymode = SS_AES_256BITS;
+		break;
+	default:
+		dev_err(ss->dev, "ERROR: Invalid keylen %u\n", keylen);
+		crypto_ablkcipher_set_flags(tfm, CRYPTO_TFM_RES_BAD_KEY_LEN);
+		return -EINVAL;
+	}
+	op->keylen = keylen;
+	memcpy(op->key, key, keylen);
+	return 0;
+}
+
+/* check and set the DES key, prepare the mode to be used */
+int sun4i_ss_des_setkey(struct crypto_ablkcipher *tfm, const u8 *key,
+			unsigned int keylen)
+{
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_ss_ctx *ss = op->ss;
+	u32 flags;
+	u32 tmp[DES_EXPKEY_WORDS];
+	int ret;
+
+	if (unlikely(keylen != DES_KEY_SIZE)) {
+		dev_err(ss->dev, "Invalid keylen %u\n", keylen);
+		crypto_ablkcipher_set_flags(tfm, CRYPTO_TFM_RES_BAD_KEY_LEN);
+		return -EINVAL;
+	}
+
+	flags = crypto_ablkcipher_get_flags(tfm);
+
+	ret = des_ekey(tmp, key);
+	if (unlikely(ret == 0) && (flags & CRYPTO_TFM_REQ_WEAK_KEY)) {
+		crypto_ablkcipher_set_flags(tfm, CRYPTO_TFM_RES_WEAK_KEY);
+		dev_dbg(ss->dev, "Weak key %u\n", keylen);
+		return -EINVAL;
+	}
+
+	op->keylen = keylen;
+	memcpy(op->key, key, keylen);
+	return 0;
+}
+
+/* check and set the 3DES key, prepare the mode to be used */
+int sun4i_ss_des3_setkey(struct crypto_ablkcipher *tfm, const u8 *key,
+			 unsigned int keylen)
+{
+	struct sun4i_tfm_ctx *op = crypto_ablkcipher_ctx(tfm);
+	struct sun4i_ss_ctx *ss = op->ss;
+
+	if (unlikely(keylen != 3 * DES_KEY_SIZE)) {
+		dev_err(ss->dev, "Invalid keylen %u\n", keylen);
+		crypto_ablkcipher_set_flags(tfm, CRYPTO_TFM_RES_BAD_KEY_LEN);
+		return -EINVAL;
+	}
+	op->keylen = keylen;
+	memcpy(op->key, key, keylen);
+	return 0;
+}
diff --git a/drivers/crypto/sunxi-ss/sun4i-ss-core.c b/drivers/crypto/sunxi-ss/sun4i-ss-core.c
new file mode 100644
index 0000000..0b79b58
--- /dev/null
+++ b/drivers/crypto/sunxi-ss/sun4i-ss-core.c
@@ -0,0 +1,403 @@
+/*
+ * sun4i-ss-core.c - hardware cryptographic accelerator for Allwinner A20 SoC
+ *
+ * Copyright (C) 2013-2015 Corentin LABBE <clabbe.montjoie@gmail.com>
+ *
+ * Core file which registers crypto algorithms supported by the SS.
+ *
+ * You could find a link for the datasheet in Documentation/arm/sunxi/README
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/clk.h>
+#include <linux/crypto.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <crypto/scatterwalk.h>
+#include <linux/scatterlist.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+
+#include "sun4i-ss.h"
+
+static struct sun4i_ss_alg_template ss_algs[] = {
+{       .type = CRYPTO_ALG_TYPE_AHASH,
+	.mode = SS_OP_MD5,
+	.alg.hash = {
+		.init = sun4i_hash_init,
+		.update = sun4i_hash_update,
+		.final = sun4i_hash_final,
+		.finup = sun4i_hash_finup,
+		.digest = sun4i_hash_digest,
+		.export = sun4i_hash_export_md5,
+		.import = sun4i_hash_import_md5,
+		.halg = {
+			.digestsize = MD5_DIGEST_SIZE,
+			.base = {
+				.cra_name = "md5",
+				.cra_driver_name = "md5-sun4i-ss",
+				.cra_priority = 300,
+				.cra_alignmask = 3,
+				.cra_flags = CRYPTO_ALG_TYPE_AHASH,
+				.cra_blocksize = MD5_HMAC_BLOCK_SIZE,
+				.cra_ctxsize = sizeof(struct sun4i_req_ctx),
+				.cra_module = THIS_MODULE,
+				.cra_type = &crypto_ahash_type,
+				.cra_init = sun4i_hash_crainit
+			}
+		}
+	}
+},
+{       .type = CRYPTO_ALG_TYPE_AHASH,
+	.mode = SS_OP_SHA1,
+	.alg.hash = {
+		.init = sun4i_hash_init,
+		.update = sun4i_hash_update,
+		.final = sun4i_hash_final,
+		.finup = sun4i_hash_finup,
+		.digest = sun4i_hash_digest,
+		.export = sun4i_hash_export_sha1,
+		.import = sun4i_hash_import_sha1,
+		.halg = {
+			.digestsize = SHA1_DIGEST_SIZE,
+			.base = {
+				.cra_name = "sha1",
+				.cra_driver_name = "sha1-sun4i-ss",
+				.cra_priority = 300,
+				.cra_alignmask = 3,
+				.cra_flags = CRYPTO_ALG_TYPE_AHASH,
+				.cra_blocksize = SHA1_BLOCK_SIZE,
+				.cra_ctxsize = sizeof(struct sun4i_req_ctx),
+				.cra_module = THIS_MODULE,
+				.cra_type = &crypto_ahash_type,
+				.cra_init = sun4i_hash_crainit
+			}
+		}
+	}
+},
+{       .type = CRYPTO_ALG_TYPE_ABLKCIPHER,
+	.alg.crypto = {
+		.cra_name = "cbc(aes)",
+		.cra_driver_name = "cbc-aes-sun4i-ss",
+		.cra_priority = 300,
+		.cra_blocksize = AES_BLOCK_SIZE,
+		.cra_flags = CRYPTO_ALG_TYPE_ABLKCIPHER,
+		.cra_ctxsize = sizeof(struct sun4i_tfm_ctx),
+		.cra_module = THIS_MODULE,
+		.cra_alignmask = 3,
+		.cra_type = &crypto_ablkcipher_type,
+		.cra_init = sun4i_ss_cipher_init,
+		.cra_ablkcipher = {
+			.min_keysize	= AES_MIN_KEY_SIZE,
+			.max_keysize	= AES_MAX_KEY_SIZE,
+			.ivsize		= AES_BLOCK_SIZE,
+			.setkey         = sun4i_ss_aes_setkey,
+			.encrypt        = sun4i_ss_cbc_aes_encrypt,
+			.decrypt        = sun4i_ss_cbc_aes_decrypt,
+		}
+	}
+},
+{       .type = CRYPTO_ALG_TYPE_ABLKCIPHER,
+	.alg.crypto = {
+		.cra_name = "ecb(aes)",
+		.cra_driver_name = "ecb-aes-sun4i-ss",
+		.cra_priority = 300,
+		.cra_blocksize = AES_BLOCK_SIZE,
+		.cra_flags = CRYPTO_ALG_TYPE_ABLKCIPHER,
+		.cra_ctxsize = sizeof(struct sun4i_tfm_ctx),
+		.cra_module = THIS_MODULE,
+		.cra_alignmask = 3,
+		.cra_type = &crypto_ablkcipher_type,
+		.cra_init = sun4i_ss_cipher_init,
+		.cra_ablkcipher = {
+			.min_keysize	= AES_MIN_KEY_SIZE,
+			.max_keysize	= AES_MAX_KEY_SIZE,
+			.ivsize		= AES_BLOCK_SIZE,
+			.setkey         = sun4i_ss_aes_setkey,
+			.encrypt        = sun4i_ss_ecb_aes_encrypt,
+			.decrypt        = sun4i_ss_ecb_aes_decrypt,
+		}
+	}
+},
+{       .type = CRYPTO_ALG_TYPE_ABLKCIPHER,
+	.alg.crypto = {
+		.cra_name = "cbc(des)",
+		.cra_driver_name = "cbc-des-sun4i-ss",
+		.cra_priority = 300,
+		.cra_blocksize = DES_BLOCK_SIZE,
+		.cra_flags = CRYPTO_ALG_TYPE_ABLKCIPHER,
+		.cra_ctxsize = sizeof(struct sun4i_req_ctx),
+		.cra_module = THIS_MODULE,
+		.cra_alignmask = 3,
+		.cra_type = &crypto_ablkcipher_type,
+		.cra_init = sun4i_ss_cipher_init,
+		.cra_u.ablkcipher = {
+			.min_keysize    = DES_KEY_SIZE,
+			.max_keysize    = DES_KEY_SIZE,
+			.ivsize         = DES_BLOCK_SIZE,
+			.setkey         = sun4i_ss_des_setkey,
+			.encrypt        = sun4i_ss_cbc_des_encrypt,
+			.decrypt        = sun4i_ss_cbc_des_decrypt,
+		}
+	}
+},
+{       .type = CRYPTO_ALG_TYPE_ABLKCIPHER,
+	.alg.crypto = {
+		.cra_name = "ecb(des)",
+		.cra_driver_name = "ecb-des-sun4i-ss",
+		.cra_priority = 300,
+		.cra_blocksize = DES_BLOCK_SIZE,
+		.cra_flags = CRYPTO_ALG_TYPE_ABLKCIPHER,
+		.cra_ctxsize = sizeof(struct sun4i_req_ctx),
+		.cra_module = THIS_MODULE,
+		.cra_alignmask = 3,
+		.cra_type = &crypto_ablkcipher_type,
+		.cra_init = sun4i_ss_cipher_init,
+		.cra_u.ablkcipher = {
+			.min_keysize    = DES_KEY_SIZE,
+			.max_keysize    = DES_KEY_SIZE,
+			.setkey         = sun4i_ss_des_setkey,
+			.encrypt        = sun4i_ss_ecb_des_encrypt,
+			.decrypt        = sun4i_ss_ecb_des_decrypt,
+		}
+	}
+},
+{       .type = CRYPTO_ALG_TYPE_ABLKCIPHER,
+	.alg.crypto = {
+			.cra_name = "cbc(des3_ede)",
+			.cra_driver_name = "cbc-des3-sun4i-ss",
+			.cra_priority = 300,
+			.cra_blocksize = DES3_EDE_BLOCK_SIZE,
+			.cra_flags = CRYPTO_ALG_TYPE_ABLKCIPHER,
+			.cra_ctxsize = sizeof(struct sun4i_req_ctx),
+			.cra_module = THIS_MODULE,
+			.cra_alignmask = 3,
+			.cra_type = &crypto_ablkcipher_type,
+			.cra_init = sun4i_ss_cipher_init,
+			.cra_u.ablkcipher = {
+				.min_keysize    = DES3_EDE_KEY_SIZE,
+				.max_keysize    = DES3_EDE_KEY_SIZE,
+				.ivsize         = DES3_EDE_BLOCK_SIZE,
+				.setkey         = sun4i_ss_des3_setkey,
+				.encrypt        = sun4i_ss_cbc_des3_encrypt,
+				.decrypt        = sun4i_ss_cbc_des3_decrypt,
+		}
+	}
+},
+{       .type = CRYPTO_ALG_TYPE_ABLKCIPHER,
+	.alg.crypto = {
+			.cra_name = "ecb(des3_ede)",
+			.cra_driver_name = "ecb-des3-sun4i-ss",
+			.cra_priority = 300,
+			.cra_blocksize = DES3_EDE_BLOCK_SIZE,
+			.cra_flags = CRYPTO_ALG_TYPE_ABLKCIPHER,
+			.cra_ctxsize = sizeof(struct sun4i_req_ctx),
+			.cra_module = THIS_MODULE,
+			.cra_alignmask = 3,
+			.cra_type = &crypto_ablkcipher_type,
+			.cra_init = sun4i_ss_cipher_init,
+			.cra_u.ablkcipher = {
+				.min_keysize    = DES3_EDE_KEY_SIZE,
+				.max_keysize    = DES3_EDE_KEY_SIZE,
+				.ivsize         = DES3_EDE_BLOCK_SIZE,
+				.setkey         = sun4i_ss_des3_setkey,
+				.encrypt        = sun4i_ss_ecb_des3_encrypt,
+				.decrypt        = sun4i_ss_ecb_des3_decrypt,
+		}
+	}
+},
+};
+
+static int sun4i_ss_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	u32 v;
+	int err, i;
+	unsigned long cr;
+	const unsigned long cr_ahb = 24 * 1000 * 1000;
+	const unsigned long cr_mod = 150 * 1000 * 1000;
+	struct sun4i_ss_ctx *ss;
+
+	if (!pdev->dev.of_node)
+		return -ENODEV;
+
+	ss = devm_kzalloc(&pdev->dev, sizeof(*ss), GFP_KERNEL);
+	if (!ss)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ss->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ss->base)) {
+		dev_err(&pdev->dev, "Cannot request MMIO\n");
+		return PTR_ERR(ss->base);
+	}
+
+	ss->ssclk = devm_clk_get(&pdev->dev, "mod");
+	if (IS_ERR(ss->ssclk)) {
+		err = PTR_ERR(ss->ssclk);
+		dev_err(&pdev->dev, "Cannot get SS clock err=%d\n", err);
+		return err;
+	}
+	dev_dbg(&pdev->dev, "clock ss acquired\n");
+
+	ss->busclk = devm_clk_get(&pdev->dev, "ahb");
+	if (IS_ERR(ss->busclk)) {
+		err = PTR_ERR(ss->busclk);
+		dev_err(&pdev->dev, "Cannot get AHB SS clock err=%d\n", err);
+		return err;
+	}
+	dev_dbg(&pdev->dev, "clock ahb_ss acquired\n");
+
+	/* Enable both clocks */
+	err = clk_prepare_enable(ss->busclk);
+	if (err != 0) {
+		dev_err(&pdev->dev, "Cannot prepare_enable busclk\n");
+		return err;
+	}
+	err = clk_prepare_enable(ss->ssclk);
+	if (err != 0) {
+		dev_err(&pdev->dev, "Cannot prepare_enable ssclk\n");
+		goto error_ssclk;
+	}
+
+	/*
+	 * Check that clock have the correct rates given in the datasheet
+	 * Try to set the clock to the maximum allowed
+	 */
+	err = clk_set_rate(ss->ssclk, cr_mod);
+	if (err != 0) {
+		dev_err(&pdev->dev, "Cannot set clock rate to ssclk\n");
+		goto error_clk;
+	}
+
+	/*
+	 * The only impact on clocks below requirement are bad performance,
+	 * so do not print "errors"
+	 * warn on Overclocked clocks
+	 */
+	cr = clk_get_rate(ss->busclk);
+	if (cr >= cr_ahb)
+		dev_dbg(&pdev->dev, "Clock bus %lu (%lu MHz) (must be >= %lu)\n",
+			cr, cr / 1000000, cr_ahb);
+	else
+		dev_warn(&pdev->dev, "Clock bus %lu (%lu MHz) (must be >= %lu)\n",
+			 cr, cr / 1000000, cr_ahb);
+
+	cr = clk_get_rate(ss->ssclk);
+	if (cr <= cr_mod)
+		if (cr < cr_mod)
+			dev_warn(&pdev->dev, "Clock ss %lu (%lu MHz) (must be <= %lu)\n",
+				 cr, cr / 1000000, cr_mod);
+		else
+			dev_dbg(&pdev->dev, "Clock ss %lu (%lu MHz) (must be <= %lu)\n",
+				cr, cr / 1000000, cr_mod);
+	else
+		dev_warn(&pdev->dev, "Clock ss is at %lu (%lu MHz) (must be <= %lu)\n",
+			 cr, cr / 1000000, cr_mod);
+
+	/*
+	 * Datasheet named it "Die Bonding ID"
+	 * I expect to be a sort of Security System Revision number.
+	 * Since the A80 seems to have an other version of SS
+	 * this info could be useful
+	 */
+	writel(SS_ENABLED, ss->base + SS_CTL);
+	v = readl(ss->base + SS_CTL);
+	v >>= 16;
+	v &= 0x07;
+	dev_info(&pdev->dev, "Die ID %d\n", v);
+	writel(0, ss->base + SS_CTL);
+
+	ss->dev = &pdev->dev;
+
+	spin_lock_init(&ss->slock);
+
+	for (i = 0; i < ARRAY_SIZE(ss_algs); i++) {
+		ss_algs[i].ss = ss;
+		switch (ss_algs[i].type) {
+		case CRYPTO_ALG_TYPE_ABLKCIPHER:
+			err = crypto_register_alg(&ss_algs[i].alg.crypto);
+			if (err != 0) {
+				dev_err(ss->dev, "Fail to register %s\n",
+					ss_algs[i].alg.crypto.cra_name);
+				goto error_alg;
+			}
+			break;
+		case CRYPTO_ALG_TYPE_AHASH:
+			err = crypto_register_ahash(&ss_algs[i].alg.hash);
+			if (err != 0) {
+				dev_err(ss->dev, "Fail to register %s\n",
+					ss_algs[i].alg.hash.halg.base.cra_name);
+				goto error_alg;
+			}
+			break;
+		}
+	}
+	platform_set_drvdata(pdev, ss);
+	return 0;
+error_alg:
+	i--;
+	for (; i >= 0; i--) {
+		switch (ss_algs[i].type) {
+		case CRYPTO_ALG_TYPE_ABLKCIPHER:
+			crypto_unregister_alg(&ss_algs[i].alg.crypto);
+			break;
+		case CRYPTO_ALG_TYPE_AHASH:
+			crypto_unregister_ahash(&ss_algs[i].alg.hash);
+			break;
+		}
+	}
+error_clk:
+	clk_disable_unprepare(ss->ssclk);
+error_ssclk:
+	clk_disable_unprepare(ss->busclk);
+	return err;
+}
+
+static int sun4i_ss_remove(struct platform_device *pdev)
+{
+	int i;
+	struct sun4i_ss_ctx *ss = platform_get_drvdata(pdev);
+
+	for (i = 0; i < ARRAY_SIZE(ss_algs); i++) {
+		switch (ss_algs[i].type) {
+		case CRYPTO_ALG_TYPE_ABLKCIPHER:
+			crypto_unregister_alg(&ss_algs[i].alg.crypto);
+			break;
+		case CRYPTO_ALG_TYPE_AHASH:
+			crypto_unregister_ahash(&ss_algs[i].alg.hash);
+			break;
+		}
+	}
+
+	writel(0, ss->base + SS_CTL);
+	clk_disable_unprepare(ss->busclk);
+	clk_disable_unprepare(ss->ssclk);
+	return 0;
+}
+
+static const struct of_device_id a20ss_crypto_of_match_table[] = {
+	{ .compatible = "allwinner,sun4i-a10-crypto" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, a20ss_crypto_of_match_table);
+
+static struct platform_driver sun4i_ss_driver = {
+	.probe          = sun4i_ss_probe,
+	.remove         = sun4i_ss_remove,
+	.driver         = {
+		.name           = "sun4i-ss",
+		.of_match_table	= a20ss_crypto_of_match_table,
+	},
+};
+
+module_platform_driver(sun4i_ss_driver);
+
+MODULE_DESCRIPTION("Allwinner Security System cryptographic accelerator");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Corentin LABBE <clabbe.montjoie@gmail.com>");
diff --git a/drivers/crypto/sunxi-ss/sun4i-ss-hash.c b/drivers/crypto/sunxi-ss/sun4i-ss-hash.c
new file mode 100644
index 0000000..ff80314
--- /dev/null
+++ b/drivers/crypto/sunxi-ss/sun4i-ss-hash.c
@@ -0,0 +1,492 @@
+/*
+ * sun4i-ss-hash.c - hardware cryptographic accelerator for Allwinner A20 SoC
+ *
+ * Copyright (C) 2013-2015 Corentin LABBE <clabbe.montjoie@gmail.com>
+ *
+ * This file add support for MD5 and SHA1.
+ *
+ * You could find the datasheet in Documentation/arm/sunxi/README
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include "sun4i-ss.h"
+#include <linux/scatterlist.h>
+
+/* This is a totally arbitrary value */
+#define SS_TIMEOUT 100
+
+int sun4i_hash_crainit(struct crypto_tfm *tfm)
+{
+	crypto_ahash_set_reqsize(__crypto_ahash_cast(tfm),
+				 sizeof(struct sun4i_req_ctx));
+	return 0;
+}
+
+/* sun4i_hash_init: initialize request context */
+int sun4i_hash_init(struct ahash_request *areq)
+{
+	struct sun4i_req_ctx *op = ahash_request_ctx(areq);
+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
+	struct ahash_alg *alg = __crypto_ahash_alg(tfm->base.__crt_alg);
+	struct sun4i_ss_alg_template *algt;
+	struct sun4i_ss_ctx *ss;
+
+	memset(op, 0, sizeof(struct sun4i_req_ctx));
+
+	algt = container_of(alg, struct sun4i_ss_alg_template, alg.hash);
+	ss = algt->ss;
+	op->ss = algt->ss;
+	op->mode = algt->mode;
+
+	return 0;
+}
+
+int sun4i_hash_export_md5(struct ahash_request *areq, void *out)
+{
+	struct sun4i_req_ctx *op = ahash_request_ctx(areq);
+	struct md5_state *octx = out;
+	int i;
+
+	octx->byte_count = op->byte_count + op->len;
+
+	memcpy(octx->block, op->buf, op->len);
+
+	if (op->byte_count > 0) {
+		for (i = 0; i < 4; i++)
+			octx->hash[i] = op->hash[i];
+	} else {
+		octx->hash[0] = SHA1_H0;
+		octx->hash[1] = SHA1_H1;
+		octx->hash[2] = SHA1_H2;
+		octx->hash[3] = SHA1_H3;
+	}
+
+	return 0;
+}
+
+int sun4i_hash_import_md5(struct ahash_request *areq, const void *in)
+{
+	struct sun4i_req_ctx *op = ahash_request_ctx(areq);
+	const struct md5_state *ictx = in;
+	int i;
+
+	sun4i_hash_init(areq);
+
+	op->byte_count = ictx->byte_count & ~0x3F;
+	op->len = ictx->byte_count & 0x3F;
+
+	memcpy(op->buf, ictx->block, op->len);
+
+	for (i = 0; i < 4; i++)
+		op->hash[i] = ictx->hash[i];
+
+	return 0;
+}
+
+int sun4i_hash_export_sha1(struct ahash_request *areq, void *out)
+{
+	struct sun4i_req_ctx *op = ahash_request_ctx(areq);
+	struct sha1_state *octx = out;
+	int i;
+
+	octx->count = op->byte_count + op->len;
+
+	memcpy(octx->buffer, op->buf, op->len);
+
+	if (op->byte_count > 0) {
+		for (i = 0; i < 5; i++)
+			octx->state[i] = op->hash[i];
+	} else {
+		octx->state[0] = SHA1_H0;
+		octx->state[1] = SHA1_H1;
+		octx->state[2] = SHA1_H2;
+		octx->state[3] = SHA1_H3;
+		octx->state[4] = SHA1_H4;
+	}
+
+	return 0;
+}
+
+int sun4i_hash_import_sha1(struct ahash_request *areq, const void *in)
+{
+	struct sun4i_req_ctx *op = ahash_request_ctx(areq);
+	const struct sha1_state *ictx = in;
+	int i;
+
+	sun4i_hash_init(areq);
+
+	op->byte_count = ictx->count & ~0x3F;
+	op->len = ictx->count & 0x3F;
+
+	memcpy(op->buf, ictx->buffer, op->len);
+
+	for (i = 0; i < 5; i++)
+		op->hash[i] = ictx->state[i];
+
+	return 0;
+}
+
+/*
+ * sun4i_hash_update: update hash engine
+ *
+ * Could be used for both SHA1 and MD5
+ * Write data by step of 32bits and put then in the SS.
+ *
+ * Since we cannot leave partial data and hash state in the engine,
+ * we need to get the hash state at the end of this function.
+ * We can get the hash state every 64 bytes
+ *
+ * So the first work is to get the number of bytes to write to SS modulo 64
+ * The extra bytes will go to a temporary buffer op->buf storing op->len bytes
+ *
+ * So at the begin of update()
+ * if op->len + areq->nbytes < 64
+ * => all data will be written to wait buffer (op->buf) and end=0
+ * if not, write all data from op->buf to the device and position end to
+ * complete to 64bytes
+ *
+ * example 1:
+ * update1 60o => op->len=60
+ * update2 60o => need one more word to have 64 bytes
+ * end=4
+ * so write all data from op->buf and one word of SGs
+ * write remaining data in op->buf
+ * final state op->len=56
+ */
+int sun4i_hash_update(struct ahash_request *areq)
+{
+	u32 v, ivmode = 0;
+	unsigned int i = 0;
+	/*
+	 * i is the total bytes read from SGs, to be compared to areq->nbytes
+	 * i is important because we cannot rely on SG length since the sum of
+	 * SG->length could be greater than areq->nbytes
+	 */
+
+	struct sun4i_req_ctx *op = ahash_request_ctx(areq);
+	struct sun4i_ss_ctx *ss = op->ss;
+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
+	unsigned int in_i = 0; /* advancement in the current SG */
+	unsigned int end;
+	/*
+	 * end is the position when we need to stop writing to the device,
+	 * to be compared to i
+	 */
+	int in_r, err = 0;
+	unsigned int todo;
+	u32 spaces, rx_cnt = SS_RX_DEFAULT;
+	size_t copied = 0;
+	struct sg_mapping_iter mi;
+
+	dev_dbg(ss->dev, "%s %s bc=%llu len=%u mode=%x wl=%u h0=%0x",
+		__func__, crypto_tfm_alg_name(areq->base.tfm),
+		op->byte_count, areq->nbytes, op->mode,
+		op->len, op->hash[0]);
+
+	if (areq->nbytes == 0)
+		return 0;
+
+	/* protect against overflow */
+	if (areq->nbytes > UINT_MAX - op->len) {
+		dev_err(ss->dev, "Cannot process too large request\n");
+		return -EINVAL;
+	}
+
+	if (op->len + areq->nbytes < 64) {
+		/* linearize data to op->buf */
+		copied = sg_pcopy_to_buffer(areq->src, sg_nents(areq->src),
+					    op->buf + op->len, areq->nbytes, 0);
+		op->len += copied;
+		return 0;
+	}
+
+	end = ((areq->nbytes + op->len) / 64) * 64 - op->len;
+
+	if (end > areq->nbytes || areq->nbytes - end > 63) {
+		dev_err(ss->dev, "ERROR: Bound error %u %u\n",
+			end, areq->nbytes);
+		return -EINVAL;
+	}
+
+	spin_lock_bh(&ss->slock);
+
+	/*
+	 * if some data have been processed before,
+	 * we need to restore the partial hash state
+	 */
+	if (op->byte_count > 0) {
+		ivmode = SS_IV_ARBITRARY;
+		for (i = 0; i < 5; i++)
+			writel(op->hash[i], ss->base + SS_IV0 + i * 4);
+	}
+	/* Enable the device */
+	writel(op->mode | SS_ENABLED | ivmode, ss->base + SS_CTL);
+
+	i = 0;
+	sg_miter_start(&mi, areq->src, sg_nents(areq->src),
+		       SG_MITER_FROM_SG | SG_MITER_ATOMIC);
+	sg_miter_next(&mi);
+	in_i = 0;
+
+	do {
+		/*
+		 * we need to linearize in two case:
+		 * - the buffer is already used
+		 * - the SG does not have enough byte remaining ( < 4)
+		 */
+		if (op->len > 0 || (mi.length - in_i) < 4) {
+			/*
+			 * if we have entered here we have two reason to stop
+			 * - the buffer is full
+			 * - reach the end
+			 */
+			while (op->len < 64 && i < end) {
+				/* how many bytes we can read from current SG */
+				in_r = min3(mi.length - in_i, end - i,
+					    64 - op->len);
+				memcpy(op->buf + op->len, mi.addr + in_i, in_r);
+				op->len += in_r;
+				i += in_r;
+				in_i += in_r;
+				if (in_i == mi.length) {
+					sg_miter_next(&mi);
+					in_i = 0;
+				}
+			}
+			if (op->len > 3 && (op->len % 4) == 0) {
+				/* write buf to the device */
+				writesl(ss->base + SS_RXFIFO, op->buf,
+					op->len / 4);
+				op->byte_count += op->len;
+				op->len = 0;
+			}
+		}
+		if (mi.length - in_i > 3 && i < end) {
+			/* how many bytes we can read from current SG */
+			in_r = min3(mi.length - in_i, areq->nbytes - i,
+				    ((mi.length - in_i) / 4) * 4);
+			/* how many bytes we can write in the device*/
+			todo = min3((u32)(end - i) / 4, rx_cnt, (u32)in_r / 4);
+			writesl(ss->base + SS_RXFIFO, mi.addr + in_i, todo);
+			op->byte_count += todo * 4;
+			i += todo * 4;
+			in_i += todo * 4;
+			rx_cnt -= todo;
+			if (rx_cnt == 0) {
+				spaces = readl(ss->base + SS_FCSR);
+				rx_cnt = SS_RXFIFO_SPACES(spaces);
+			}
+			if (in_i == mi.length) {
+				sg_miter_next(&mi);
+				in_i = 0;
+			}
+		}
+	} while (i < end);
+	/* final linear */
+	if ((areq->nbytes - i) < 64) {
+		while (i < areq->nbytes && in_i < mi.length && op->len < 64) {
+			/* how many bytes we can read from current SG */
+			in_r = min3(mi.length - in_i, areq->nbytes - i,
+				    64 - op->len);
+			memcpy(op->buf + op->len, mi.addr + in_i, in_r);
+			op->len += in_r;
+			i += in_r;
+			in_i += in_r;
+			if (in_i == mi.length) {
+				sg_miter_next(&mi);
+				in_i = 0;
+			}
+		}
+	}
+
+	sg_miter_stop(&mi);
+
+	writel(op->mode | SS_ENABLED | SS_DATA_END, ss->base + SS_CTL);
+	i = 0;
+	do {
+		v = readl(ss->base + SS_CTL);
+		i++;
+	} while (i < SS_TIMEOUT && (v & SS_DATA_END) > 0);
+	if (i >= SS_TIMEOUT) {
+		dev_err_ratelimited(ss->dev,
+				    "ERROR: hash end timeout %d>%d ctl=%x len=%u\n",
+				    i, SS_TIMEOUT, v, areq->nbytes);
+		err = -EIO;
+		goto release_ss;
+	}
+
+	/* get the partial hash only if something was written */
+	for (i = 0; i < crypto_ahash_digestsize(tfm) / 4; i++)
+		op->hash[i] = readl(ss->base + SS_MD0 + i * 4);
+
+release_ss:
+	writel(0, ss->base + SS_CTL);
+	spin_unlock_bh(&ss->slock);
+	return err;
+}
+
+/*
+ * sun4i_hash_final: finalize hashing operation
+ *
+ * If we have some remaining bytes, we write them.
+ * Then ask the SS for finalizing the hashing operation
+ *
+ * I do not check RX FIFO size in this function since the size is 32
+ * after each enabling and this function neither write more than 32 words.
+ */
+int sun4i_hash_final(struct ahash_request *areq)
+{
+	u32 v, ivmode = 0;
+	unsigned int i;
+	unsigned int j = 0;
+	int zeros, err = 0;
+	unsigned int index, padlen;
+	__be64 bits;
+	struct sun4i_req_ctx *op = ahash_request_ctx(areq);
+	struct sun4i_ss_ctx *ss = op->ss;
+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
+	u32 bf[32];
+	u32 wb = 0;
+	unsigned int nwait, nbw = 0;
+
+	dev_dbg(ss->dev, "%s: byte=%llu len=%u mode=%x wl=%u h=%x",
+		__func__, op->byte_count, areq->nbytes, op->mode,
+		op->len, op->hash[0]);
+
+	spin_lock_bh(&ss->slock);
+
+	/*
+	 * if we have already written something,
+	 * restore the partial hash state
+	 */
+	if (op->byte_count > 0) {
+		ivmode = SS_IV_ARBITRARY;
+		for (i = 0; i < crypto_ahash_digestsize(tfm) / 4; i++)
+			writel(op->hash[i], ss->base + SS_IV0 + i * 4);
+	}
+	writel(op->mode | SS_ENABLED | ivmode, ss->base + SS_CTL);
+
+	/* write the remaining words of the wait buffer */
+	if (op->len > 0) {
+		nwait = op->len / 4;
+		if (nwait > 0) {
+			writesl(ss->base + SS_RXFIFO, op->buf, nwait);
+			op->byte_count += 4 * nwait;
+		}
+		nbw = op->len - 4 * nwait;
+		wb = *(u32 *)(op->buf + nwait * 4);
+		wb &= (0xFFFFFFFF >> (4 - nbw) * 8);
+	}
+
+	/* write the remaining bytes of the nbw buffer */
+	if (nbw > 0) {
+		wb |= ((1 << 7) << (nbw * 8));
+		bf[j++] = wb;
+	} else {
+		bf[j++] = 1 << 7;
+	}
+
+	/*
+	 * number of space to pad to obtain 64o minus 8(size) minus 4 (final 1)
+	 * I take the operations from other MD5/SHA1 implementations
+	 */
+
+	/* we have already send 4 more byte of which nbw data */
+	if (op->mode == SS_OP_MD5) {
+		index = (op->byte_count + 4) & 0x3f;
+		op->byte_count += nbw;
+		if (index > 56)
+			zeros = (120 - index) / 4;
+		else
+			zeros = (56 - index) / 4;
+	} else {
+		op->byte_count += nbw;
+		index = op->byte_count & 0x3f;
+		padlen = (index < 56) ? (56 - index) : ((64 + 56) - index);
+		zeros = (padlen - 1) / 4;
+	}
+
+	memset(bf + j, 0, 4 * zeros);
+	j += zeros;
+
+	/* write the length of data */
+	if (op->mode == SS_OP_SHA1) {
+		bits = cpu_to_be64(op->byte_count << 3);
+		bf[j++] = bits & 0xffffffff;
+		bf[j++] = (bits >> 32) & 0xffffffff;
+	} else {
+		bf[j++] = (op->byte_count << 3) & 0xffffffff;
+		bf[j++] = (op->byte_count >> 29) & 0xffffffff;
+	}
+	writesl(ss->base + SS_RXFIFO, bf, j);
+
+	/* Tell the SS to stop the hashing */
+	writel(op->mode | SS_ENABLED | SS_DATA_END, ss->base + SS_CTL);
+
+	/*
+	 * Wait for SS to finish the hash.
+	 * The timeout could happen only in case of bad overcloking
+	 * or driver bug.
+	 */
+	i = 0;
+	do {
+		v = readl(ss->base + SS_CTL);
+		i++;
+	} while (i < SS_TIMEOUT && (v & SS_DATA_END) > 0);
+	if (i >= SS_TIMEOUT) {
+		dev_err_ratelimited(ss->dev,
+				    "ERROR: hash end timeout %d>%d ctl=%x len=%u\n",
+				    i, SS_TIMEOUT, v, areq->nbytes);
+		err = -EIO;
+		goto release_ss;
+	}
+
+	/* Get the hash from the device */
+	if (op->mode == SS_OP_SHA1) {
+		for (i = 0; i < 5; i++) {
+			v = cpu_to_be32(readl(ss->base + SS_MD0 + i * 4));
+			memcpy(areq->result + i * 4, &v, 4);
+		}
+	} else {
+		for (i = 0; i < 4; i++) {
+			v = readl(ss->base + SS_MD0 + i * 4);
+			memcpy(areq->result + i * 4, &v, 4);
+		}
+	}
+
+release_ss:
+	writel(0, ss->base + SS_CTL);
+	spin_unlock_bh(&ss->slock);
+	return err;
+}
+
+/* sun4i_hash_finup: finalize hashing operation after an update */
+int sun4i_hash_finup(struct ahash_request *areq)
+{
+	int err;
+
+	err = sun4i_hash_update(areq);
+	if (err != 0)
+		return err;
+
+	return sun4i_hash_final(areq);
+}
+
+/* combo of init/update/final functions */
+int sun4i_hash_digest(struct ahash_request *areq)
+{
+	int err;
+
+	err = sun4i_hash_init(areq);
+	if (err != 0)
+		return err;
+
+	err = sun4i_hash_update(areq);
+	if (err != 0)
+		return err;
+
+	return sun4i_hash_final(areq);
+}
diff --git a/drivers/crypto/sunxi-ss/sun4i-ss.h b/drivers/crypto/sunxi-ss/sun4i-ss.h
new file mode 100644
index 0000000..db18b25
--- /dev/null
+++ b/drivers/crypto/sunxi-ss/sun4i-ss.h
@@ -0,0 +1,199 @@
+/*
+ * sun4i-ss.h - hardware cryptographic accelerator for Allwinner A20 SoC
+ *
+ * Copyright (C) 2013-2015 Corentin LABBE <clabbe.montjoie@gmail.com>
+ *
+ * Support AES cipher with 128,192,256 bits keysize.
+ * Support MD5 and SHA1 hash algorithms.
+ * Support DES and 3DES
+ *
+ * You could find the datasheet in Documentation/arm/sunxi/README
+ *
+ * Licensed under the GPL-2.
+ */
+
+#include <linux/clk.h>
+#include <linux/crypto.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <crypto/scatterwalk.h>
+#include <linux/scatterlist.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <crypto/md5.h>
+#include <crypto/sha.h>
+#include <crypto/hash.h>
+#include <crypto/internal/hash.h>
+#include <crypto/aes.h>
+#include <crypto/des.h>
+#include <crypto/internal/rng.h>
+
+#define SS_CTL            0x00
+#define SS_KEY0           0x04
+#define SS_KEY1           0x08
+#define SS_KEY2           0x0C
+#define SS_KEY3           0x10
+#define SS_KEY4           0x14
+#define SS_KEY5           0x18
+#define SS_KEY6           0x1C
+#define SS_KEY7           0x20
+
+#define SS_IV0            0x24
+#define SS_IV1            0x28
+#define SS_IV2            0x2C
+#define SS_IV3            0x30
+
+#define SS_FCSR           0x44
+
+#define SS_MD0            0x4C
+#define SS_MD1            0x50
+#define SS_MD2            0x54
+#define SS_MD3            0x58
+#define SS_MD4            0x5C
+
+#define SS_RXFIFO         0x200
+#define SS_TXFIFO         0x204
+
+/* SS_CTL configuration values */
+
+/* PRNG generator mode - bit 15 */
+#define SS_PRNG_ONESHOT		(0 << 15)
+#define SS_PRNG_CONTINUE	(1 << 15)
+
+/* IV mode for hash */
+#define SS_IV_ARBITRARY		(1 << 14)
+
+/* SS operation mode - bits 12-13 */
+#define SS_ECB			(0 << 12)
+#define SS_CBC			(1 << 12)
+#define SS_CTS			(3 << 12)
+
+/* Counter width for CNT mode - bits 10-11 */
+#define SS_CNT_16BITS		(0 << 10)
+#define SS_CNT_32BITS		(1 << 10)
+#define SS_CNT_64BITS		(2 << 10)
+
+/* Key size for AES - bits 8-9 */
+#define SS_AES_128BITS		(0 << 8)
+#define SS_AES_192BITS		(1 << 8)
+#define SS_AES_256BITS		(2 << 8)
+
+/* Operation direction - bit 7 */
+#define SS_ENCRYPTION		(0 << 7)
+#define SS_DECRYPTION		(1 << 7)
+
+/* SS Method - bits 4-6 */
+#define SS_OP_AES		(0 << 4)
+#define SS_OP_DES		(1 << 4)
+#define SS_OP_3DES		(2 << 4)
+#define SS_OP_SHA1		(3 << 4)
+#define SS_OP_MD5		(4 << 4)
+#define SS_OP_PRNG		(5 << 4)
+
+/* Data end bit - bit 2 */
+#define SS_DATA_END		(1 << 2)
+
+/* PRNG start bit - bit 1 */
+#define SS_PRNG_START		(1 << 1)
+
+/* SS Enable bit - bit 0 */
+#define SS_DISABLED		(0 << 0)
+#define SS_ENABLED		(1 << 0)
+
+/* SS_FCSR configuration values */
+/* RX FIFO status - bit 30 */
+#define SS_RXFIFO_FREE		(1 << 30)
+
+/* RX FIFO empty spaces - bits 24-29 */
+#define SS_RXFIFO_SPACES(val)	(((val) >> 24) & 0x3f)
+
+/* TX FIFO status - bit 22 */
+#define SS_TXFIFO_AVAILABLE	(1 << 22)
+
+/* TX FIFO available spaces - bits 16-21 */
+#define SS_TXFIFO_SPACES(val)	(((val) >> 16) & 0x3f)
+
+#define SS_RX_MAX	32
+#define SS_RX_DEFAULT	SS_RX_MAX
+#define SS_TX_MAX	33
+
+#define SS_RXFIFO_EMP_INT_PENDING	(1 << 10)
+#define SS_TXFIFO_AVA_INT_PENDING	(1 << 8)
+#define SS_RXFIFO_EMP_INT_ENABLE	(1 << 2)
+#define SS_TXFIFO_AVA_INT_ENABLE	(1 << 0)
+
+struct sun4i_ss_ctx {
+	void __iomem *base;
+	int irq;
+	struct clk *busclk;
+	struct clk *ssclk;
+	struct device *dev;
+	struct resource *res;
+	spinlock_t slock; /* control the use of the device */
+};
+
+struct sun4i_ss_alg_template {
+	u32 type;
+	u32 mode;
+	union {
+		struct crypto_alg crypto;
+		struct ahash_alg hash;
+	} alg;
+	struct sun4i_ss_ctx *ss;
+};
+
+struct sun4i_tfm_ctx {
+	u32 key[AES_MAX_KEY_SIZE / 4];/* divided by sizeof(u32) */
+	u32 keylen;
+	u32 keymode;
+	struct sun4i_ss_ctx *ss;
+};
+
+struct sun4i_cipher_req_ctx {
+	u32 mode;
+};
+
+struct sun4i_req_ctx {
+	u32 mode;
+	u64 byte_count; /* number of bytes "uploaded" to the device */
+	u32 hash[5]; /* for storing SS_IVx register */
+	char buf[64];
+	unsigned int len;
+	struct sun4i_ss_ctx *ss;
+};
+
+int sun4i_hash_crainit(struct crypto_tfm *tfm);
+int sun4i_hash_init(struct ahash_request *areq);
+int sun4i_hash_update(struct ahash_request *areq);
+int sun4i_hash_final(struct ahash_request *areq);
+int sun4i_hash_finup(struct ahash_request *areq);
+int sun4i_hash_digest(struct ahash_request *areq);
+int sun4i_hash_export_md5(struct ahash_request *areq, void *out);
+int sun4i_hash_import_md5(struct ahash_request *areq, const void *in);
+int sun4i_hash_export_sha1(struct ahash_request *areq, void *out);
+int sun4i_hash_import_sha1(struct ahash_request *areq, const void *in);
+
+int sun4i_ss_cbc_aes_encrypt(struct ablkcipher_request *areq);
+int sun4i_ss_cbc_aes_decrypt(struct ablkcipher_request *areq);
+int sun4i_ss_ecb_aes_encrypt(struct ablkcipher_request *areq);
+int sun4i_ss_ecb_aes_decrypt(struct ablkcipher_request *areq);
+
+int sun4i_ss_cbc_des_encrypt(struct ablkcipher_request *areq);
+int sun4i_ss_cbc_des_decrypt(struct ablkcipher_request *areq);
+int sun4i_ss_ecb_des_encrypt(struct ablkcipher_request *areq);
+int sun4i_ss_ecb_des_decrypt(struct ablkcipher_request *areq);
+
+int sun4i_ss_cbc_des3_encrypt(struct ablkcipher_request *areq);
+int sun4i_ss_cbc_des3_decrypt(struct ablkcipher_request *areq);
+int sun4i_ss_ecb_des3_encrypt(struct ablkcipher_request *areq);
+int sun4i_ss_ecb_des3_decrypt(struct ablkcipher_request *areq);
+
+int sun4i_ss_cipher_init(struct crypto_tfm *tfm);
+int sun4i_ss_aes_setkey(struct crypto_ablkcipher *tfm, const u8 *key,
+			unsigned int keylen);
+int sun4i_ss_des_setkey(struct crypto_ablkcipher *tfm, const u8 *key,
+			unsigned int keylen);
+int sun4i_ss_des3_setkey(struct crypto_ablkcipher *tfm, const u8 *key,
+			 unsigned int keylen);
-- 
2.3.6

[PATCH v11 5/5] MAINTAINERS: Add myself as maintainer of Allwinner Security System

[LABBE Corentin]

Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
---
 MAINTAINERS | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 2d3d55c..308da53 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -556,6 +556,12 @@ S:	Maintained
 F:	Documentation/i2c/busses/i2c-ali1563
 F:	drivers/i2c/busses/i2c-ali1563.c
 
+ALLWINNER SECURITY SYSTEM
+M:	Corentin Labbe <clabbe.montjoie@gmail.com>
+L:	linux-crypto@vger.kernel.org
+S:	Maintained
+F:	drivers/crypto/sunxi-ss/
+
 ALPHA PORT
 M:	Richard Henderson <rth@twiddle.net>
 M:	Ivan Kokshaysky <ink@jurassic.park.msu.ru>
-- 
2.3.6

Re: [PATCH v11] crypto: Add Allwinner Security System crypto accelerator

[Herbert Xu]

On Fri, Jul 17, 2015 at 04:39:37PM +0200, LABBE Corentin wrote:
> Hello
> 
> This is the driver for the Security System included in Allwinner SoC A20.
> The Security System (SS for short) is a hardware cryptographic accelerator that
> support AES/MD5/SHA1/DES/3DES/PRNG algorithms.
> It could be found on others Allwinner SoC: 
> - A10, A10s, A13, A31 and A33 manual give the same datasheet for SS than A20
> - A23 speak about a security system but without precisions
> - A80 and A83T datasheet speak about a security system with more functions
>   (SHA224/SHA256/RSA/CRC), they will be supported in a separate driver.

All applied.  Thanks a lot!
-- 
Email: Herbert Xu <herbert@gondor.apana.org.au>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt

Re: [PATCH v11] crypto: Add Allwinner Security System crypto accelerator

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 905 bytes --]

On Mon, Jul 20, 2015 at 04:10:50PM +0800, Herbert Xu wrote:
> On Fri, Jul 17, 2015 at 04:39:37PM +0200, LABBE Corentin wrote:
> > Hello
> > 
> > This is the driver for the Security System included in Allwinner SoC A20.
> > The Security System (SS for short) is a hardware cryptographic accelerator that
> > support AES/MD5/SHA1/DES/3DES/PRNG algorithms.
> > It could be found on others Allwinner SoC: 
> > - A10, A10s, A13, A31 and A33 manual give the same datasheet for SS than A20
> > - A23 speak about a security system but without precisions
> > - A80 and A83T datasheet speak about a security system with more functions
> >   (SHA224/SHA256/RSA/CRC), they will be supported in a separate driver.
> 
> All applied.  Thanks a lot!

All applied, DT bits included?

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v11] crypto: Add Allwinner Security System crypto accelerator

[Herbert Xu]

On Mon, Jul 20, 2015 at 10:18:36AM +0200, Maxime Ripard wrote:
> On Mon, Jul 20, 2015 at 04:10:50PM +0800, Herbert Xu wrote:
> > On Fri, Jul 17, 2015 at 04:39:37PM +0200, LABBE Corentin wrote:
> > > Hello
> > > 
> > > This is the driver for the Security System included in Allwinner SoC A20.
> > > The Security System (SS for short) is a hardware cryptographic accelerator that
> > > support AES/MD5/SHA1/DES/3DES/PRNG algorithms.
> > > It could be found on others Allwinner SoC: 
> > > - A10, A10s, A13, A31 and A33 manual give the same datasheet for SS than A20
> > > - A23 speak about a security system but without precisions
> > > - A80 and A83T datasheet speak about a security system with more functions
> > >   (SHA224/SHA256/RSA/CRC), they will be supported in a separate driver.
> > 
> > All applied.  Thanks a lot!
> 
> All applied, DT bits included?

Yes.
-- 
Email: Herbert Xu <herbert@gondor.apana.org.au>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt

Re: [PATCH v11] crypto: Add Allwinner Security System crypto accelerator

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1277 bytes --]

On Mon, Jul 20, 2015 at 04:20:57PM +0800, Herbert Xu wrote:
> On Mon, Jul 20, 2015 at 10:18:36AM +0200, Maxime Ripard wrote:
> > On Mon, Jul 20, 2015 at 04:10:50PM +0800, Herbert Xu wrote:
> > > On Fri, Jul 17, 2015 at 04:39:37PM +0200, LABBE Corentin wrote:
> > > > Hello
> > > > 
> > > > This is the driver for the Security System included in Allwinner SoC A20.
> > > > The Security System (SS for short) is a hardware cryptographic accelerator that
> > > > support AES/MD5/SHA1/DES/3DES/PRNG algorithms.
> > > > It could be found on others Allwinner SoC: 
> > > > - A10, A10s, A13, A31 and A33 manual give the same datasheet for SS than A20
> > > > - A23 speak about a security system but without precisions
> > > > - A80 and A83T datasheet speak about a security system with more functions
> > > >   (SHA224/SHA256/RSA/CRC), they will be supported in a separate driver.
> > > 
> > > All applied.  Thanks a lot!
> > 
> > All applied, DT bits included?
> 
> Yes.

I thought you needed at least my Acked-by for that, but
whatever... How are we supposed to handle subsequent DT patches that
should be merged through arm-soc then?

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v11] crypto: Add Allwinner Security System crypto accelerator

[Herbert Xu]

On Tue, Jul 21, 2015 at 02:38:47PM +0200, Maxime Ripard wrote:
> I thought you needed at least my Acked-by for that, but
> whatever... How are we supposed to handle subsequent DT patches that
> should be merged through arm-soc then?

What subsequent patches are you referring to? The changes in
this series are fairly self-contained so it should be unlikely
to cause serious merge conflicts.

Cheers,
-- 
Email: Herbert Xu <herbert@gondor.apana.org.au>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt

Re: [PATCH v11] crypto: Add Allwinner Security System crypto accelerator

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 683 bytes --]

On Tue, Jul 21, 2015 at 08:50:14PM +0800, Herbert Xu wrote:
> On Tue, Jul 21, 2015 at 02:38:47PM +0200, Maxime Ripard wrote:
> > I thought you needed at least my Acked-by for that, but
> > whatever... How are we supposed to handle subsequent DT patches that
> > should be merged through arm-soc then?
> 
> What subsequent patches are you referring to? The changes in
> this series are fairly self-contained so it should be unlikely
> to cause serious merge conflicts.

Enabling it in other boards / SoCs, and/or any change that might
conflict with this one.

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]