[PATCH v6 0/6] mmc: imx: a few fixes and new feature

[PATCH v6 0/6] mmc: imx: a few fixes and new feature

[Haibo Chen]

Changes for v6:
-remove duplicate code in esdhc_set_uhs_signaling().
-fix a typo for patch-2.
-make commit log of patch-3 more specific.

Haibo Chen (6):
  mmc: sdhci-esdhc-imx: add imx7d support and support HS400
  mmc: sdhci-esdhc-imx: add tuning-step setting support
  mmc: sdhci-esdhc-imx: add imx7d support in bingding doc
  ARM: dts: imx7d-sdb: add eMMC5.0 support
  mmc: sdhci-esdhc-imx: set back the burst_length_enable bit to 1
  mmc: sdhci-esdhc-imx: change default watermark level and burst length

 .../devicetree/bindings/mmc/fsl-imx-esdhc.txt      |   6 ++
 arch/arm/boot/dts/imx7d-sdb.dts                    |  13 +++
 drivers/mmc/host/sdhci-esdhc-imx.c                 | 114 ++++++++++++++++++++-
 include/linux/platform_data/mmc-esdhc-imx.h        |   1 +
 4 files changed, 130 insertions(+), 4 deletions(-)

-- 
1.9.1

[PATCH v6 1/6] mmc: sdhci-esdhc-imx: add imx7d support and support HS400

[Haibo Chen]

The imx7d usdhc is derived from imx6sx, the difference is that
imx7d support HS400.

So introduce a new compatible string for imx7d and add HS400
support for imx7d usdhc.

Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
---
 drivers/mmc/host/sdhci-esdhc-imx.c | 86 ++++++++++++++++++++++++++++++++++++--
 1 file changed, 83 insertions(+), 3 deletions(-)

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index c6b9f64..b8b7e88 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -44,6 +44,7 @@
 #define  ESDHC_MIX_CTRL_EXE_TUNE	(1 << 22)
 #define  ESDHC_MIX_CTRL_SMPCLK_SEL	(1 << 23)
 #define  ESDHC_MIX_CTRL_FBCLK_SEL	(1 << 25)
+#define  ESDHC_MIX_CTRL_HS400_EN	(1 << 26)
 /* Bits 3 and 6 are not SDHCI standard definitions */
 #define  ESDHC_MIX_CTRL_SDHCI_MASK	0xb7
 /* Tuning bits */
@@ -60,6 +61,16 @@
 #define  ESDHC_TUNE_CTRL_MIN		0
 #define  ESDHC_TUNE_CTRL_MAX		((1 << 7) - 1)
 
+/* strobe dll register */
+#define ESDHC_STROBE_DLL_CTRL		0x70
+#define ESDHC_STROBE_DLL_CTRL_ENABLE	(1 << 0)
+#define ESDHC_STROBE_DLL_CTRL_RESET	(1 << 1)
+#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT	3
+
+#define ESDHC_STROBE_DLL_STATUS		0x74
+#define ESDHC_STROBE_DLL_STS_REF_LOCK	(1 << 1)
+#define ESDHC_STROBE_DLL_STS_SLV_LOCK	0x1
+
 #define ESDHC_TUNING_CTRL		0xcc
 #define ESDHC_STD_TUNING_EN		(1 << 24)
 /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
@@ -120,6 +131,11 @@
 #define ESDHC_FLAG_ERR004536		BIT(7)
 /* The IP supports HS200 mode */
 #define ESDHC_FLAG_HS200		BIT(8)
+/* The IP supports HS400 mode */
+#define ESDHC_FLAG_HS400		BIT(9)
+
+/* A higher clock ferquency than this rate requires strobell dll control */
+#define ESDHC_STROBE_DLL_CLK_FREQ	100000000
 
 struct esdhc_soc_data {
 	u32 flags;
@@ -156,6 +172,12 @@ static struct esdhc_soc_data usdhc_imx6sx_data = {
 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200,
 };
 
+static struct esdhc_soc_data usdhc_imx7d_data = {
+	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
+			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
+			| ESDHC_FLAG_HS400,
+};
+
 struct pltfm_imx_data {
 	u32 scratchpad;
 	struct pinctrl *pinctrl;
@@ -199,6 +221,7 @@ static const struct of_device_id imx_esdhc_dt_ids[] = {
 	{ .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
 	{ .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
 	{ .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
+	{ .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
@@ -274,6 +297,9 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
 				val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
 					| SDHCI_SUPPORT_SDR50
 					| SDHCI_USE_SDR50_TUNING;
+
+			if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
+				val |= SDHCI_SUPPORT_HS400;
 		}
 	}
 
@@ -774,6 +800,7 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
 		break;
 	case MMC_TIMING_UHS_SDR104:
 	case MMC_TIMING_MMC_HS200:
+	case MMC_TIMING_MMC_HS400:
 		pinctrl = imx_data->pins_200mhz;
 		break;
 	default:
@@ -784,24 +811,68 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
 	return pinctrl_select_state(imx_data->pinctrl, pinctrl);
 }
 
+/*
+ * For HS400 eMMC, there is a data_strobe line, this signal is generated
+ * by the device and used for data output and CRC status response output
+ * in HS400 mode. The frequency of this signal follows the frequency of
+ * CLK generated by host. Host receive the data which is aligned to the
+ * edge of data_strobe line. Due to the time delay between CLK line and
+ * data_strobe line, if the delay time is larger than one clock cycle,
+ * then CLK and data_strobe line will misaligned, read error shows up.
+ * So when the CLK is higher than 100MHz, each clock cycle is short enough,
+ * host should config the delay target.
+ */
+static void esdhc_set_strobe_dll(struct sdhci_host *host)
+{
+	u32 v;
+
+	if (host->mmc->actual_clock > ESDHC_STROBE_DLL_CLK_FREQ) {
+		/* force a reset on strobe dll */
+		writel(ESDHC_STROBE_DLL_CTRL_RESET,
+			host->ioaddr + ESDHC_STROBE_DLL_CTRL);
+		/*
+		 * enable strobe dll ctrl and adjust the delay target
+		 * for the uSDHC loopback read clock
+		 */
+		v = ESDHC_STROBE_DLL_CTRL_ENABLE |
+			(7 << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
+		writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
+		/* wait 1us to make sure strobe dll status register stable */
+		udelay(1);
+		v = readl(host->ioaddr + ESDHC_STROBE_DLL_STATUS);
+		if (!(v & ESDHC_STROBE_DLL_STS_REF_LOCK))
+			dev_warn(mmc_dev(host->mmc),
+				"warning! HS400 strobe DLL status REF not lock!\n");
+		if (!(v & ESDHC_STROBE_DLL_STS_SLV_LOCK))
+			dev_warn(mmc_dev(host->mmc),
+				"warning! HS400 strobe DLL status SLV not lock!\n");
+	}
+}
+
 static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
 {
+	u32 m;
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct pltfm_imx_data *imx_data = pltfm_host->priv;
 	struct esdhc_platform_data *boarddata = &imx_data->boarddata;
 
+	/* disable ddr mode and disable HS400 mode */
+	m = readl(host->ioaddr + ESDHC_MIX_CTRL);
+	m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN);
+	imx_data->is_ddr = 0;
+
 	switch (timing) {
 	case MMC_TIMING_UHS_SDR12:
 	case MMC_TIMING_UHS_SDR25:
 	case MMC_TIMING_UHS_SDR50:
 	case MMC_TIMING_UHS_SDR104:
 	case MMC_TIMING_MMC_HS200:
+		writel(m, host->ioaddr + ESDHC_MIX_CTRL);
 		break;
 	case MMC_TIMING_UHS_DDR50:
 	case MMC_TIMING_MMC_DDR52:
-		writel(readl(host->ioaddr + ESDHC_MIX_CTRL) |
-				ESDHC_MIX_CTRL_DDREN,
-				host->ioaddr + ESDHC_MIX_CTRL);
+		m |= ESDHC_MIX_CTRL_DDREN;
+		writel(m, host->ioaddr + ESDHC_MIX_CTRL);
 		imx_data->is_ddr = 1;
 		if (boarddata->delay_line) {
 			u32 v;
@@ -813,6 +884,12 @@ static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
 			writel(v, host->ioaddr + ESDHC_DLL_CTRL);
 		}
 		break;
+	case MMC_TIMING_MMC_HS400:
+		m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
+		writel(m, host->ioaddr + ESDHC_MIX_CTRL);
+		imx_data->is_ddr = 1;
+		esdhc_set_strobe_dll(host);
+		break;
 	}
 
 	esdhc_change_pinstate(host, timing);
@@ -1100,6 +1177,9 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
 	if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536)
 		host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
 
+	if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
+		host->quirks2 |= SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400;
+
 	if (of_id)
 		err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data);
 	else
-- 
1.9.1

[PATCH v6 2/6] mmc: sdhci-esdhc-imx: add tuning-step setting support

[Haibo Chen]

tuning-step is the delay cell steps in tuning procedure. The default value
of tuning-step is 1. Some boards or cards need another value to pass the
tuning procedure. For example, imx7d-sdb board need the tuning-step value
as 2, otherwise it can't pass the tuning procedure.

So this patch add the tuning-step setting in driver, so that user can set
the tuning-step value in dts.

Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
---
 drivers/mmc/host/sdhci-esdhc-imx.c          | 9 +++++++++
 include/linux/platform_data/mmc-esdhc-imx.h | 1 +
 2 files changed, 10 insertions(+)

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index b8b7e88..298551d 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -75,6 +75,7 @@
 #define ESDHC_STD_TUNING_EN		(1 << 24)
 /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
 #define ESDHC_TUNING_START_TAP		0x1
+#define ESDHC_TUNING_STEP_SHIFT		16
 
 /* pinctrl state */
 #define ESDHC_PINCTRL_STATE_100MHZ	"state_100mhz"
@@ -474,6 +475,7 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
 		} else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
 			u32 v = readl(host->ioaddr + SDHCI_ACMD12_ERR);
 			u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
+			u32 tuning_ctrl;
 			if (val & SDHCI_CTRL_TUNED_CLK) {
 				v |= ESDHC_MIX_CTRL_SMPCLK_SEL;
 			} else {
@@ -484,6 +486,11 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
 			if (val & SDHCI_CTRL_EXEC_TUNING) {
 				v |= ESDHC_MIX_CTRL_EXE_TUNE;
 				m |= ESDHC_MIX_CTRL_FBCLK_SEL;
+				tuning_ctrl = readl(host->ioaddr + ESDHC_TUNING_CTRL);
+				tuning_ctrl |= ESDHC_STD_TUNING_EN | ESDHC_TUNING_START_TAP;
+				if (imx_data->boarddata.tuning_step)
+					tuning_ctrl |= imx_data->boarddata.tuning_step << ESDHC_TUNING_STEP_SHIFT;
+					writel(tuning_ctrl, host->ioaddr + ESDHC_TUNING_CTRL);
 			} else {
 				v &= ~ESDHC_MIX_CTRL_EXE_TUNE;
 			}
@@ -963,6 +970,8 @@ sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
 	if (gpio_is_valid(boarddata->wp_gpio))
 		boarddata->wp_type = ESDHC_WP_GPIO;
 
+	of_property_read_u32(np, "fsl,tuning-step", &boarddata->tuning_step);
+
 	if (of_find_property(np, "no-1-8-v", NULL))
 		boarddata->support_vsel = false;
 	else
diff --git a/include/linux/platform_data/mmc-esdhc-imx.h b/include/linux/platform_data/mmc-esdhc-imx.h
index e1571ef..95ccab3 100644
--- a/include/linux/platform_data/mmc-esdhc-imx.h
+++ b/include/linux/platform_data/mmc-esdhc-imx.h
@@ -45,5 +45,6 @@ struct esdhc_platform_data {
 	int max_bus_width;
 	bool support_vsel;
 	unsigned int delay_line;
+	unsigned int tuning_step;       /* The delay cell steps in tuning procedure */
 };
 #endif /* __ASM_ARCH_IMX_ESDHC_H */
-- 
1.9.1

[PATCH v6 3/6] mmc: sdhci-esdhc-imx: add imx7d support in bingding doc

[Haibo Chen]

Add a required property "fsl,imx7d-usdhc" in binding doc.
Add an optional property "fsl,tuning-step" in binding doc.

Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
---
 Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
index 211e778..dca56d6 100644
--- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
+++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
@@ -15,6 +15,7 @@ Required properties:
 	       "fsl,imx6q-usdhc"
 	       "fsl,imx6sl-usdhc"
 	       "fsl,imx6sx-usdhc"
+	       "fsl,imx7d-usdhc"
 
 Optional properties:
 - fsl,wp-controller : Indicate to use controller internal write protection
@@ -27,6 +28,11 @@ Optional properties:
   transparent level shifters on the outputs of the controller. Two cells are
   required, first cell specifies minimum slot voltage (mV), second cell
   specifies maximum slot voltage (mV). Several ranges could be specified.
+- fsl,tuning-step: Specify the increasing delay cell steps in tuning procedure.
+  The uSDHC use one delay cell as default increasing step to do tuning process.
+  This property allows user to change the tuning step to more than one delay
+  cells which is useful for some special boards or cards when the default
+  tuning step can't find the proper delay window within limited tuning retries.
 
 Examples:
 
-- 
1.9.1

[PATCH v6 4/6] ARM: dts: imx7d-sdb: add eMMC5.0 support

[Haibo Chen]

imx7d-sdb board has a eMMC5.0 on usdhc3. This eMMC support HS400.
This patch add usdhc3 support for HS400

Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
---
 arch/arm/boot/dts/imx7d-sdb.dts | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index fdd1d7c..8059458 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -241,6 +241,19 @@
 	status = "okay";
 };
 
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
+	assigned-clock-rates = <400000000>;
+	bus-width = <8>;
+	fsl,tuning-step = <2>;
+	non-removable;
+	status = "okay";
+};
+
 &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
-- 
1.9.1

[PATCH v6 5/6] mmc: sdhci-esdhc-imx: set back the burst_length_enable bit to 1

[Haibo Chen]

Currently we find that if a usdhc is choosed to boot system, then ROM
code will set the burst length enable bit of this usdhc as 0.

This will make performance drop a lot if this usdhc's burst length is
configed. So this patch set back the burst_length_enable bit as 1,
which is the default value, and means burst length is enabled for INCR.

Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
---
 drivers/mmc/host/sdhci-esdhc-imx.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index 298551d..ac8ec01 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -32,6 +32,7 @@
 #include "sdhci-esdhc.h"
 
 #define	ESDHC_CTRL_D3CD			0x08
+#define ESDHC_BURST_LEN_EN_INCR		(1 << 27)
 /* VENDOR SPEC register */
 #define ESDHC_VENDOR_SPEC		0xc0
 #define  ESDHC_VENDOR_SPEC_SDIO_QUIRK	(1 << 1)
@@ -1163,6 +1164,21 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
 		host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
 		host->mmc->caps |= MMC_CAP_1_8V_DDR;
 
+		/*
+		 * ROM code will change the bit burst_length_enable setting
+		 * to zero if this usdhc is choosed to boot system. Change
+		 * it back here, otherwise it will impact the performance a
+		 * lot. This bit is used to enable/disable the burst length
+		 * for the external AHB2AXI bridge, it's usefully especially
+		 * for INCR transfer because without burst length indicator,
+		 * the AHB2AXI bridge does not know the burst length in
+		 * advance. And without burst length indicator, AHB INCR
+		 * transfer can only be converted to singles on the AXI side.
+		 */
+		writel(readl(host->ioaddr + SDHCI_HOST_CONTROL)
+			| ESDHC_BURST_LEN_EN_INCR,
+			host->ioaddr + SDHCI_HOST_CONTROL);
+
 		if (!(imx_data->socdata->flags & ESDHC_FLAG_HS200))
 			host->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200;
 
-- 
1.9.1

[PATCH v6 6/6] mmc: sdhci-esdhc-imx: change default watermark level and burst length

[Haibo Chen]

By default, for all imx SoC types, the watermark level is 16, and the
burst length is 8. But if the SDIO/SD/MMC I/O speed is fast enough,
this default watermark level and burst length will be the performance
bottleneck.

For example, i.MX7D support eMMC HS400 mode, this mode can run in 8 bit,
200MHZ DDR mode. So the I/O speed improve a lot compare to SD3.0.
The default burst length is 8, if we don't change this value, in
HS400 mode, when we do eMMC read operation, we can find that the
clock signal will stop for a period of time. This means the speed
of data moving on AHB bus is slower than I/O speed. So we should
improve the speed of data moving on AHB bus.

This patch set the default burst length as 16, and set the default
watermark level as 64. The test result is the clock signal has
no stop during the eMMC HS400 operation.

Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
---
 drivers/mmc/host/sdhci-esdhc-imx.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index ac8ec01..886d230 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -1160,7 +1160,8 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
 	 * to something insane.  Change it back here.
 	 */
 	if (esdhc_is_usdhc(imx_data)) {
-		writel(0x08100810, host->ioaddr + ESDHC_WTMK_LVL);
+		writel(0x10401040, host->ioaddr + ESDHC_WTMK_LVL);
+
 		host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
 		host->mmc->caps |= MMC_CAP_1_8V_DDR;
 
-- 
1.9.1

Re: [PATCH v6 0/6] mmc: imx: a few fixes and new feature

[Dong Aisheng]

On Tue, Aug 11, 2015 at 07:38:25PM +0800, Haibo Chen wrote:
> Changes for v6:
> -remove duplicate code in esdhc_set_uhs_signaling().
> -fix a typo for patch-2.
> -make commit log of patch-3 more specific.
> 
> Haibo Chen (6):
>   mmc: sdhci-esdhc-imx: add imx7d support and support HS400
>   mmc: sdhci-esdhc-imx: add tuning-step setting support
>   mmc: sdhci-esdhc-imx: add imx7d support in bingding doc
>   ARM: dts: imx7d-sdb: add eMMC5.0 support
>   mmc: sdhci-esdhc-imx: set back the burst_length_enable bit to 1
>   mmc: sdhci-esdhc-imx: change default watermark level and burst length
> 
>  .../devicetree/bindings/mmc/fsl-imx-esdhc.txt      |   6 ++
>  arch/arm/boot/dts/imx7d-sdb.dts                    |  13 +++
>  drivers/mmc/host/sdhci-esdhc-imx.c                 | 114 ++++++++++++++++++++-
>  include/linux/platform_data/mmc-esdhc-imx.h        |   1 +
>  4 files changed, 130 insertions(+), 4 deletions(-)
> 
> -- 
> 1.9.1
> 

The patch set looks good to me.

Acked-by: Dong Aisheng <aisheng.dong@freescale.com>

Regards
Dong Aisheng

Re: [PATCH v6 0/6] mmc: imx: a few fixes and new feature

[Haibo Chen]

On Thu, Aug 13, 2015 at 04:58:56PM +0800, Dong Aisheng wrote:
> On Tue, Aug 11, 2015 at 07:38:25PM +0800, Haibo Chen wrote:
> > Changes for v6:
> > -remove duplicate code in esdhc_set_uhs_signaling().
> > -fix a typo for patch-2.
> > -make commit log of patch-3 more specific.
> > 
> > Haibo Chen (6):
> >   mmc: sdhci-esdhc-imx: add imx7d support and support HS400
> >   mmc: sdhci-esdhc-imx: add tuning-step setting support
> >   mmc: sdhci-esdhc-imx: add imx7d support in bingding doc
> >   ARM: dts: imx7d-sdb: add eMMC5.0 support
> >   mmc: sdhci-esdhc-imx: set back the burst_length_enable bit to 1
> >   mmc: sdhci-esdhc-imx: change default watermark level and burst length
> > 
> >  .../devicetree/bindings/mmc/fsl-imx-esdhc.txt      |   6 ++
> >  arch/arm/boot/dts/imx7d-sdb.dts                    |  13 +++
> >  drivers/mmc/host/sdhci-esdhc-imx.c                 | 114 ++++++++++++++++++++-
> >  include/linux/platform_data/mmc-esdhc-imx.h        |   1 +
> >  4 files changed, 130 insertions(+), 4 deletions(-)
> > 
> > -- 
> > 1.9.1
> > 
> 
> The patch set looks good to me.
> 
> Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
> 
> Regards
> Dong Aisheng

Hi Ulf,

Can you help pull these patches into your branch?


Best regards

Haibo
-- 

Re: [PATCH v6 0/6] mmc: imx: a few fixes and new feature

[Ulf Hansson]

On 11 August 2015 at 13:38, Haibo Chen <haibo.chen@freescale.com> wrote:
> Changes for v6:
> -remove duplicate code in esdhc_set_uhs_signaling().
> -fix a typo for patch-2.
> -make commit log of patch-3 more specific.
>
> Haibo Chen (6):
>   mmc: sdhci-esdhc-imx: add imx7d support and support HS400
>   mmc: sdhci-esdhc-imx: add tuning-step setting support
>   mmc: sdhci-esdhc-imx: add imx7d support in bingding doc
>   ARM: dts: imx7d-sdb: add eMMC5.0 support
>   mmc: sdhci-esdhc-imx: set back the burst_length_enable bit to 1
>   mmc: sdhci-esdhc-imx: change default watermark level and burst length
>
>  .../devicetree/bindings/mmc/fsl-imx-esdhc.txt      |   6 ++
>  arch/arm/boot/dts/imx7d-sdb.dts                    |  13 +++
>  drivers/mmc/host/sdhci-esdhc-imx.c                 | 114 ++++++++++++++++++++-
>  include/linux/platform_data/mmc-esdhc-imx.h        |   1 +
>  4 files changed, 130 insertions(+), 4 deletions(-)
>
> --
> 1.9.1
>

I have applied this for next - except patch4 as it needs and ack from
the IMX SOC maintainer, or it may be better to take that patch through
ARM soc...

Regarding patch3, which document the new bindings and the compatible
string, I moved this to be the first patch and fixed the spelling of
the commit message header.

Thanks!

Kind regards
Uffe

Re: [PATCH v6 4/6] ARM: dts: imx7d-sdb: add eMMC5.0 support

[Shawn Guo]

On Tue, Aug 11, 2015 at 07:38:29PM +0800, Haibo Chen wrote:
> imx7d-sdb board has a eMMC5.0 on usdhc3. This eMMC support HS400.
> This patch add usdhc3 support for HS400
> 
> Signed-off-by: Haibo Chen <haibo.chen@freescale.com>

Applied, thanks.