From: Marc Titinger <mtitinger@baylibre.com>
To: linux@roeck-us.net, jdelvare@suse.com
Cc: lm-sensors@lm-sensors.org, linux-kernel@vger.kernel.org,
bcousson@baylibre.com, mturquette@baylibre.com,
Marc Titinger <mtitinger@baylibre.com>
Subject: [PATCH v2] hwmon: ina2xx: allow for actual measurement bandwidth above 160 Hz
Date: Tue, 20 Oct 2015 10:20:44 +0200 [thread overview]
Message-ID: <1445329244-21627-1-git-send-email-mtitinger@baylibre.com> (raw)
In-Reply-To: <56259997.6080706@roeck-us.net>
With the current implementation, the driver will prevent a readout at a
pace faster than the default conversion time (2ms) times the averaging
setting, min AVG being 1:1.
Any sysfs "show" read access from the client app faster than 500 Hz will be
'cached' by the driver, but actually since do_update reads all 8 registers,
the best achievable measurement rate is roughly 8*800 us (for the time
spent in i2c-core) i.e. <= 156Hz with Beagle Bone Black.
This change set uses a register mask to allow for the readout of a single
i2c register at a time. Furthermore, performing subsequent reads on the
same register will make use of the ability of the i2c chip to retain the
last reg offset, hence use a shorter i2c message (roughly 400us instead of
800us spent in i2c-core.c).
The best readout rate for a single measurement is now around 2kHz. And for
four measurements around (1/(4*800us) = 312 Hz. Since for any readout rate
faster than 160 Hz the interval is set by the i2c transactions completion,
the 'last-update' anti-flooding code will not have a limiting effect in
practice. Hence I also remove the elapsed time checking in the hwmon driver
for ina2xx.
To summarize, the patch provides a max bandwidth improvement with hwmon
client apps from ~160 Hz to ~320 Hz, and better in single-channel
polling mode.
Signed-off-by: Marc Titinger <mtitinger@baylibre.com>
---
v2: remove local macro for BIT_MASK, use the bitops.h one.
drivers/hwmon/ina2xx.c | 88 +++++++++++++++++++++++++++++++++++++++-----------
1 file changed, 69 insertions(+), 19 deletions(-)
diff --git a/drivers/hwmon/ina2xx.c b/drivers/hwmon/ina2xx.c
index 4d28150..2f82a9b 100644
--- a/drivers/hwmon/ina2xx.c
+++ b/drivers/hwmon/ina2xx.c
@@ -105,9 +105,14 @@ struct ina2xx_data {
struct mutex update_lock;
bool valid;
- unsigned long last_updated;
int update_interval; /* in jiffies */
+ /* Last read register (slave address already set
+ * reading out from this same register repeatedly will
+ * be significantly faster!
+ */
+ int last_reg;
+
int kind;
const struct attribute_group *groups[INA2XX_MAX_ATTRIBUTE_GROUPS];
u16 regs[INA2XX_MAX_REGISTERS];
@@ -203,21 +208,63 @@ static int ina2xx_init(struct ina2xx_data *data)
return ina2xx_calibrate(data);
}
-static int ina2xx_do_update(struct device *dev)
+/*
+ * Most I2c chips will allow reading from the current register pointer
+ * w/o setting the register offset again.
+ */
+static inline s32 __i2c_read_same_word(const struct i2c_client *client)
+{
+ unsigned char msgbuf[2];
+
+ struct i2c_msg msg = {
+ .addr = client->addr,
+ .flags = client->flags | I2C_M_RD,
+ .len = 2,
+ .buf = msgbuf,
+ };
+
+ int status = i2c_transfer(client->adapter, &msg, 1);
+
+ return (status < 0) ? status : (msgbuf[1]|(msgbuf[0]<<8));
+}
+
+static int ina2xx_do_update(struct device *dev, int reg_mask)
{
struct ina2xx_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
- int i, rv, retry;
+ int i = 0, rv, retry;
dev_dbg(&client->dev, "Starting ina2xx update\n");
for (retry = 5; retry; retry--) {
- /* Read all registers */
- for (i = 0; i < data->config->registers; i++) {
- rv = i2c_smbus_read_word_swapped(client, i);
+
+ /* Try to issue a shorter i2c message */
+ if (reg_mask & (1 << data->last_reg)) {
+ rv = __i2c_read_same_word(client);
if (rv < 0)
return rv;
- data->regs[i] = rv;
+
+ reg_mask &= ~(1 << data->last_reg);
+ data->regs[data->last_reg] = rv;
+
+ dev_dbg(&client->dev, "%d, rv = %x, (last_reg)\n",
+ data->last_reg,
+ data->regs[data->last_reg]);
+ }
+
+ /* Check for remaining registers in mask. */
+ while (reg_mask && i < data->config->registers) {
+ if (reg_mask & (1L << i)) {
+ rv = i2c_smbus_read_word_swapped(client, i);
+ if (rv < 0)
+ return rv;
+ data->regs[i] = rv;
+ data->last_reg = i;
+
+ dev_dbg(&client->dev, "%d, rv = %x\n", i,
+ data->regs[i]);
+ }
+ i++;
}
/*
@@ -240,8 +287,6 @@ static int ina2xx_do_update(struct device *dev)
msleep(INA2XX_MAX_DELAY);
continue;
}
-
- data->last_updated = jiffies;
data->valid = 1;
return 0;
@@ -256,22 +301,24 @@ static int ina2xx_do_update(struct device *dev)
return -ENODEV;
}
-static struct ina2xx_data *ina2xx_update_device(struct device *dev)
+static struct ina2xx_data *ina2xx_update_device(struct device *dev,
+ int reg_mask)
{
struct ina2xx_data *data = dev_get_drvdata(dev);
struct ina2xx_data *ret = data;
- unsigned long after;
int rv;
mutex_lock(&data->update_lock);
- after = data->last_updated + data->update_interval;
- if (time_after(jiffies, after) || !data->valid) {
- rv = ina2xx_do_update(dev);
- if (rv < 0)
- ret = ERR_PTR(rv);
+ if (!data->valid) {
+ reg_mask = 0xff; /* do all regs */
+ data->last_reg = 0xff;
}
+ rv = ina2xx_do_update(dev, reg_mask);
+ if (rv < 0)
+ ret = ERR_PTR(rv);
+
mutex_unlock(&data->update_lock);
return ret;
}
@@ -316,7 +363,8 @@ static ssize_t ina2xx_show_value(struct device *dev,
struct device_attribute *da, char *buf)
{
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
- struct ina2xx_data *data = ina2xx_update_device(dev);
+ struct ina2xx_data *data = ina2xx_update_device(dev,
+ BIT_MASK(attr->index));
if (IS_ERR(data))
return PTR_ERR(data);
@@ -329,7 +377,8 @@ static ssize_t ina2xx_set_shunt(struct device *dev,
struct device_attribute *da,
const char *buf, size_t count)
{
- struct ina2xx_data *data = ina2xx_update_device(dev);
+ struct ina2xx_data *data = ina2xx_update_device(dev,
+ BIT_MASK(INA2XX_CONFIG));
unsigned long val;
int status;
@@ -390,7 +439,8 @@ static ssize_t ina226_set_interval(struct device *dev,
static ssize_t ina226_show_interval(struct device *dev,
struct device_attribute *da, char *buf)
{
- struct ina2xx_data *data = ina2xx_update_device(dev);
+ struct ina2xx_data *data = ina2xx_update_device(dev,
+ BIT_MASK(INA2XX_CONFIG));
if (IS_ERR(data))
return PTR_ERR(data);
--
1.9.1
next prev parent reply other threads:[~2015-10-20 8:21 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-10-19 16:21 [RFC] hwmon: ina2xx: allow for actual measurement bandwidth above 160 Hz Marc Titinger
2015-10-20 1:32 ` Guenter Roeck
2015-10-20 7:58 ` Marc Titinger
2015-10-20 8:20 ` Marc Titinger [this message]
2015-10-20 12:54 ` [PATCH v2] " Guenter Roeck
2015-10-20 13:17 ` Marc Titinger
2015-10-20 13:30 ` Guenter Roeck
2015-10-20 13:46 ` Marc Titinger
2015-10-20 17:00 ` Guenter Roeck
2015-10-21 7:46 ` Marc Titinger
2015-10-20 13:52 ` Michael Turquette
2015-10-23 16:13 ` [RFC] hwmon: ina2xx: port to using remap, improve bandwidth Marc Titinger
2015-10-23 16:49 ` kbuild test robot
2015-10-23 16:52 ` Guenter Roeck
2015-10-23 20:35 ` Marc Titinger
2015-10-24 2:21 ` Guenter Roeck
2015-10-24 12:45 ` Guenter Roeck
2015-10-26 16:24 ` [PATCH 0/2] hwmon: ina2xx: convert driver to using regmap Marc Titinger
2015-10-26 16:24 ` [PATCH 1/2] " Marc Titinger
2015-10-27 1:02 ` Guenter Roeck
2015-10-27 1:12 ` Guenter Roeck
2015-10-27 9:51 ` [PATCH v2 " Marc Titinger
2015-10-28 2:47 ` Guenter Roeck
2015-10-28 9:23 ` Marc Titinger
2015-10-26 16:24 ` [PATCH 2/2] hwmon: ina2xx: give precedence to DT over checking for platform data Marc Titinger
2015-10-27 1:10 ` Guenter Roeck
2015-10-27 9:51 ` [PATCH v2 " Marc Titinger
2015-10-23 16:55 ` [RFC] hwmon: ina2xx: port to using remap, improve bandwidth kbuild test robot
2015-10-23 20:10 ` kbuild test robot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1445329244-21627-1-git-send-email-mtitinger@baylibre.com \
--to=mtitinger@baylibre.com \
--cc=bcousson@baylibre.com \
--cc=jdelvare@suse.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@roeck-us.net \
--cc=lm-sensors@lm-sensors.org \
--cc=mturquette@baylibre.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).