[PATCH v7 0/6] Build and support rk3036 SoC platform

[PATCH v7 0/6] Build and support rk3036 SoC platform

[Xing Zheng]

Hi,
  We need to support rk3036 soc platform via upstream, there are
some primary parts for the initial release of minimum system: dts,
clk-pll, smp, and clock tree for rk3036, and additional, we can use
these startup and run to init processs.

Thanks.

Changed in v7:
- removed the patch "make sure timer5 is enabled on rk3036 platforms" (applied)
- removed the patch "add support smp for rk3036" (applied)

Changed in v6:
- add hardware timer in dtsi and some the aliases of basic modules

Changed in v5:
- don't use clk_ APIs in the pll init-callback

Changed in v4:
- add some basic IP modules on rk3036.dtsi
- optimized supporting smp codes

Changed in v3:
- optimized some codes based on v2
- removed the patch "initial set time for rtc-hym8563" (useless)
- removed the patch "pinctrl" (approved)

Changed in v2:
- based on v1, add clock controller documentation
- enable timer5 startup
- add smp for cpu1
- initial set time for rtc-hym8563

Changes in v1:
- add dts, pinctrl and clock tree for rk3036 soc platform

The patchset (6):
6) ARM: dts: enable smp for rk3036
5) ARM: dts: rockchip: add core rk3036 dts
4) clk: rockchip: add clock controller for rk3036
3) clk: rockchip: add new pll-type for rk3036 and similar socs
2) clk: rockchip: add dt-binding header for rk3036
1) dt-bindings: add documentation of rk3036 clock controller


Changes in v7:
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>

Xing Zheng (6):
  dt-bindings: add documentation of rk3036 clock controller
  clk: rockchip: add dt-binding header for rk3036
  clk: rockchip: add new pll-type for rk3036 and similar socs
  clk: rockchip: add clock controller for rk3036
  ARM: dts: rockchip: add core rk3036 dts
  ARM: dts: enable smp for rk3036

 .../bindings/clock/rockchip,rk3036-cru.txt         |   56 ++
 arch/arm/boot/dts/Makefile                         |    1 +
 arch/arm/boot/dts/rk3036-evb.dts                   |   64 +++
 arch/arm/boot/dts/rk3036.dtsi                      |  552 ++++++++++++++++++++
 drivers/clk/rockchip/Makefile                      |    1 +
 drivers/clk/rockchip/clk-pll.c                     |  249 ++++++++-
 drivers/clk/rockchip/clk-rk3036.c                  |  478 +++++++++++++++++
 drivers/clk/rockchip/clk.h                         |   32 +-
 include/dt-bindings/clock/rk3036-cru.h             |  193 +++++++
 9 files changed, 1624 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt
 create mode 100644 arch/arm/boot/dts/rk3036-evb.dts
 create mode 100644 arch/arm/boot/dts/rk3036.dtsi
 create mode 100644 drivers/clk/rockchip/clk-rk3036.c
 create mode 100644 include/dt-bindings/clock/rk3036-cru.h

-- 
1.7.9.5

[PATCH v7 1/6] dt-bindings: add documentation of rk3036 clock controller

[Xing Zheng]

Add the devicetree binding for the cru on the rk3036 which quite similar
structured as previous clock controllers.


Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
---

Changes in v7: None

 .../bindings/clock/rockchip,rk3036-cru.txt         |   56 ++++++++++++++++++++
 1 file changed, 56 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt

diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt
new file mode 100644
index 0000000..ace0599
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt
@@ -0,0 +1,56 @@
+* Rockchip RK3036 Clock and Reset Unit
+
+The RK3036 clock controller generates and supplies clock to various
+controllers within the SoC and also implements a reset controller for SoC
+peripherals.
+
+Required Properties:
+
+- compatible: should be "rockchip,rk3036-cru"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- #clock-cells: should be 1.
+- #reset-cells: should be 1.
+
+Optional Properties:
+
+- rockchip,grf: phandle to the syscon managing the "general register files"
+  If missing pll rates are not changeable, due to the missing pll lock status.
+
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume. All available clocks are defined as
+preprocessor macros in the dt-bindings/clock/rk3036-cru.h headers and can be
+used in device tree sources. Similar macros exist for the reset sources in
+these files.
+
+External clocks:
+
+There are several clocks that are generated outside the SoC. It is expected
+that they are defined using standard clock bindings with following
+clock-output-names:
+ - "xin24m" - crystal input - required,
+ - "ext_i2s" - external I2S clock - optional,
+ - "ext_gmac" - external GMAC clock - optional
+
+Example: Clock controller node:
+
+	cru: cru@20000000 {
+		compatible = "rockchip,rk3036-cru";
+		reg = <0x20000000 0x1000>;
+		rockchip,grf = <&grf>;
+
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
+
+Example: UART controller node that consumes the clock generated by the clock
+  controller:
+
+	uart0: serial@20060000 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x20060000 0x100>;
+		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clocks = <&cru SCLK_UART0>;
+	};
-- 
1.7.9.5

[PATCH v7 2/6] clk: rockchip: add dt-binding header for rk3036

[Xing Zheng]

Add the dt-bindings header for the rk3036, that gets shared between
the clock controller and the clock references in the dts.


Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
---

Changes in v7: None

 include/dt-bindings/clock/rk3036-cru.h |  193 ++++++++++++++++++++++++++++++++
 1 file changed, 193 insertions(+)
 create mode 100644 include/dt-bindings/clock/rk3036-cru.h

diff --git a/include/dt-bindings/clock/rk3036-cru.h b/include/dt-bindings/clock/rk3036-cru.h
new file mode 100644
index 0000000..a2763a6
--- /dev/null
+++ b/include/dt-bindings/clock/rk3036-cru.h
@@ -0,0 +1,193 @@
+/*
+ * Copyright (c) 2015 Rockchip Electronics Co. Ltd.
+ * Author: Xing Zheng <zhengxing@rock-chips.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _DT_BINDINGS_CLK_ROCKCHIP_RK3036_H
+#define _DT_BINDINGS_CLK_ROCKCHIP_RK3036_H
+
+/* core clocks */
+#define PLL_APLL		1
+#define PLL_DPLL		2
+#define PLL_GPLL		3
+#define ARMCLK			4
+
+/* sclk gates (special clocks) */
+#define SCLK_GPU		64
+#define SCLK_SPI		65
+#define SCLK_SDMMC		68
+#define SCLK_SDIO		69
+#define SCLK_EMMC		71
+#define SCLK_NANDC		76
+#define SCLK_UART0		77
+#define SCLK_UART1		78
+#define SCLK_UART2		79
+#define SCLK_I2S		82
+#define SCLK_SPDIF		83
+#define SCLK_TIMER0		85
+#define SCLK_TIMER1		86
+#define SCLK_TIMER2		87
+#define SCLK_TIMER3		88
+#define SCLK_OTGPHY0		93
+#define SCLK_LCDC		100
+#define SCLK_HDMI		109
+#define SCLK_HEVC		111
+#define SCLK_I2S_OUT		113
+#define SCLK_SDMMC_DRV		114
+#define SCLK_SDIO_DRV		115
+#define SCLK_EMMC_DRV		117
+#define SCLK_SDMMC_SAMPLE	118
+#define SCLK_SDIO_SAMPLE	119
+#define SCLK_EMMC_SAMPLE	121
+#define SCLK_PVTM_CORE          123
+#define SCLK_PVTM_GPU           124
+#define SCLK_PVTM_VIDEO         125
+#define SCLK_MAC		151
+#define SCLK_MACREF		152
+#define SCLK_SFC		160
+
+/* aclk gates */
+#define ACLK_DMAC2		194
+#define ACLK_LCDC		197
+#define ACLK_VIO		203
+#define ACLK_VCODEC		208
+#define ACLK_CPU		209
+#define ACLK_PERI		210
+
+/* pclk gates */
+#define PCLK_GPIO0		320
+#define PCLK_GPIO1		321
+#define PCLK_GPIO2		322
+#define PCLK_GRF		329
+#define PCLK_I2C0		332
+#define PCLK_I2C1		333
+#define PCLK_I2C2		334
+#define PCLK_SPI		338
+#define PCLK_UART0		341
+#define PCLK_UART1		342
+#define PCLK_UART2		343
+#define PCLK_PWM		350
+#define PCLK_TIMER		353
+#define PCLK_HDMI		360
+#define PCLK_CPU		362
+#define PCLK_PERI		363
+#define PCLK_DDRUPCTL		364
+#define PCLK_WDT		368
+#define PCLK_ACODEC		369
+
+/* hclk gates */
+#define HCLK_OTG0		449
+#define HCLK_OTG1		450
+#define HCLK_NANDC		453
+#define HCLK_SDMMC		456
+#define HCLK_SDIO		457
+#define HCLK_EMMC		459
+#define HCLK_I2S		462
+#define HCLK_LCDC		465
+#define HCLK_ROM		467
+#define HCLK_VIO_BUS		472
+#define HCLK_VCODEC		476
+#define HCLK_CPU		477
+#define HCLK_PERI		478
+
+#define CLK_NR_CLKS		(HCLK_PERI + 1)
+
+/* soft-reset indices */
+#define SRST_CORE0		0
+#define SRST_CORE1		1
+#define SRST_CORE0_DBG		4
+#define SRST_CORE1_DBG		5
+#define SRST_CORE0_POR		8
+#define SRST_CORE1_POR		9
+#define SRST_L2C		12
+#define SRST_TOPDBG		13
+#define SRST_STRC_SYS_A		14
+#define SRST_PD_CORE_NIU	15
+
+#define SRST_TIMER2		16
+#define SRST_CPUSYS_H		17
+#define SRST_AHB2APB_H		19
+#define SRST_TIMER3		20
+#define SRST_INTMEM		21
+#define SRST_ROM		22
+#define SRST_PERI_NIU		23
+#define SRST_I2S		24
+#define SRST_DDR_PLL		25
+#define SRST_GPU_DLL		26
+#define SRST_TIMER0		27
+#define SRST_TIMER1		28
+#define SRST_CORE_DLL		29
+#define SRST_EFUSE_P		30
+#define SRST_ACODEC_P		31
+
+#define SRST_GPIO0		32
+#define SRST_GPIO1		33
+#define SRST_GPIO2		34
+#define SRST_UART0		39
+#define SRST_UART1		40
+#define SRST_UART2		41
+#define SRST_I2C0		43
+#define SRST_I2C1		44
+#define SRST_I2C2		45
+#define SRST_SFC		47
+
+#define SRST_PWM0		48
+#define SRST_DAP		51
+#define SRST_DAP_SYS		52
+#define SRST_GRF		55
+#define SRST_PERIPHSYS_A	57
+#define SRST_PERIPHSYS_H	58
+#define SRST_PERIPHSYS_P	59
+#define SRST_CPU_PERI		61
+#define SRST_EMEM_PERI		62
+#define SRST_USB_PERI		63
+
+#define SRST_DMA2		64
+#define SRST_MAC		66
+#define SRST_NANDC		68
+#define SRST_USBOTG0		69
+#define SRST_OTGC0		71
+#define SRST_USBOTG1		72
+#define SRST_OTGC1		74
+#define SRST_DDRMSCH		79
+
+#define SRST_MMC0		81
+#define SRST_SDIO		82
+#define SRST_EMMC		83
+#define SRST_SPI0		84
+#define SRST_WDT		86
+#define SRST_DDRPHY		88
+#define SRST_DDRPHY_P		89
+#define SRST_DDRCTRL		90
+#define SRST_DDRCTRL_P		91
+
+#define SRST_HDMI_P		96
+#define SRST_VIO_BUS_H		99
+#define SRST_UTMI0		103
+#define SRST_UTMI1		104
+#define SRST_USBPOR		105
+
+#define SRST_VCODEC_A		112
+#define SRST_VCODEC_H		113
+#define SRST_VIO1_A		114
+#define SRST_HEVC		115
+#define SRST_VCODEC_NIU_A	116
+#define SRST_LCDC1_A		117
+#define SRST_LCDC1_H		118
+#define SRST_LCDC1_D		119
+#define SRST_GPU		120
+#define SRST_GPU_NIU_A		122
+
+#define SRST_DBG_P		131
+
+#endif
-- 
1.7.9.5

[PATCH v7 3/6] clk: rockchip: add new pll-type for rk3036 and similar socs

[Xing Zheng]

The rk3036's pll and clock are different with base on the rk3066(rk3188,
rk3288, rk3368 use it), there are different adjust foctors and control
registers, so these should be independent and separate from the series
of rk3066s.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
---

Changes in v7: None

 drivers/clk/rockchip/clk-pll.c |  249 +++++++++++++++++++++++++++++++++++++++-
 drivers/clk/rockchip/clk.h     |   23 ++++
 2 files changed, 271 insertions(+), 1 deletion(-)

diff --git a/drivers/clk/rockchip/clk-pll.c b/drivers/clk/rockchip/clk-pll.c
index 4881eb8..83ba1e9 100644
--- a/drivers/clk/rockchip/clk-pll.c
+++ b/drivers/clk/rockchip/clk-pll.c
@@ -2,6 +2,9 @@
  * Copyright (c) 2014 MundoReader S.L.
  * Author: Heiko Stuebner <heiko@sntech.de>
  *
+ * Copyright (c) 2015 Rockchip Electronics Co. Ltd.
+ * Author: Xing Zheng <zhengxing@rock-chips.com>
+ *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or
@@ -19,6 +22,7 @@
 #include <linux/delay.h>
 #include <linux/clk-provider.h>
 #include <linux/regmap.h>
+#include <linux/clk.h>
 #include "clk.h"
 
 #define PLL_MODE_MASK		0x3
@@ -108,6 +112,243 @@ static int rockchip_pll_wait_lock(struct rockchip_clk_pll *pll)
 }
 
 /**
+ * PLL used in RK3036
+ */
+
+#define RK3036_PLLCON(i)			(i * 0x4)
+#define RK3036_PLLCON0_FBDIV_MASK		0xfff
+#define RK3036_PLLCON0_FBDIV_SHIFT		0
+#define RK3036_PLLCON0_POSTDIV1_MASK		0x7
+#define RK3036_PLLCON0_POSTDIV1_SHIFT		12
+#define RK3036_PLLCON1_REFDIV_MASK		0x3f
+#define RK3036_PLLCON1_REFDIV_SHIFT		0
+#define RK3036_PLLCON1_POSTDIV2_MASK		0x7
+#define RK3036_PLLCON1_POSTDIV2_SHIFT		6
+#define RK3036_PLLCON1_DSMPD_MASK		0x1
+#define RK3036_PLLCON1_DSMPD_SHIFT		12
+#define RK3036_PLLCON2_FRAC_MASK		0xffffff
+#define RK3036_PLLCON2_FRAC_SHIFT		0
+
+#define RK3036_PLLCON1_PWRDOWN			(1 << 13)
+
+static void rockchip_rk3036_pll_get_params(struct rockchip_clk_pll *pll,
+					struct rockchip_pll_rate_table *rate)
+{
+	u32 pllcon;
+
+	pllcon = readl_relaxed(pll->reg_base + RK3036_PLLCON(0));
+	rate->fbdiv = ((pllcon >> RK3036_PLLCON0_FBDIV_SHIFT) & RK3036_PLLCON0_FBDIV_MASK);
+	rate->postdiv1 = ((pllcon >> RK3036_PLLCON0_POSTDIV1_SHIFT) & RK3036_PLLCON0_POSTDIV1_MASK);
+
+	pllcon = readl_relaxed(pll->reg_base + RK3036_PLLCON(1));
+	rate->refdiv = ((pllcon >> RK3036_PLLCON1_REFDIV_SHIFT) & RK3036_PLLCON1_REFDIV_MASK);
+	rate->postdiv2 = ((pllcon >> RK3036_PLLCON1_POSTDIV2_SHIFT) & RK3036_PLLCON1_POSTDIV2_MASK);
+	rate->dsmpd = ((pllcon >> RK3036_PLLCON1_DSMPD_SHIFT) & RK3036_PLLCON1_DSMPD_MASK);
+
+	pllcon = readl_relaxed(pll->reg_base + RK3036_PLLCON(2));
+	rate->frac = ((pllcon >> RK3036_PLLCON2_FRAC_SHIFT) & RK3036_PLLCON2_FRAC_MASK);
+}
+
+static unsigned long rockchip_rk3036_pll_recalc_rate(struct clk_hw *hw,
+						     unsigned long prate)
+{
+	struct rockchip_clk_pll *pll = to_rockchip_clk_pll(hw);
+	struct rockchip_pll_rate_table cur;
+	u64 rate64 = prate;
+
+	rockchip_rk3036_pll_get_params(pll, &cur);
+
+	rate64 *= cur.fbdiv;
+	do_div(rate64, cur.refdiv);
+
+	if (cur.dsmpd == 0) {
+		/* fractional mode */
+		u64 frac_rate64 = prate * cur.frac;
+
+		do_div(frac_rate64, cur.refdiv);
+		rate64 += frac_rate64 >> 24;
+	}
+
+	do_div(rate64, cur.postdiv1);
+	do_div(rate64, cur.postdiv2);
+
+	return (unsigned long)rate64;
+}
+
+static int rockchip_rk3036_pll_set_params(struct rockchip_clk_pll *pll,
+				const struct rockchip_pll_rate_table *rate)
+{
+	const struct clk_ops *pll_mux_ops = pll->pll_mux_ops;
+	struct clk_mux *pll_mux = &pll->pll_mux;
+	struct rockchip_pll_rate_table cur;
+	u32 pllcon;
+	int rate_change_remuxed = 0;
+	int cur_parent;
+	int ret;
+
+	pr_debug("%s: rate settings for %lu fbdiv: %d, postdiv1: %d, refdiv: %d, postdiv2: %d, dsmpd: %d, frac: %d\n",
+		__func__, rate->rate, rate->fbdiv, rate->postdiv1, rate->refdiv,
+		rate->postdiv2, rate->dsmpd, rate->frac);
+
+	rockchip_rk3036_pll_get_params(pll, &cur);
+	cur.rate = 0;
+
+	cur_parent = pll_mux_ops->get_parent(&pll_mux->hw);
+	if (cur_parent == PLL_MODE_NORM) {
+		pll_mux_ops->set_parent(&pll_mux->hw, PLL_MODE_SLOW);
+		rate_change_remuxed = 1;
+	}
+
+	/* update pll values */
+	writel_relaxed(HIWORD_UPDATE(rate->fbdiv, RK3036_PLLCON0_FBDIV_MASK,
+					  RK3036_PLLCON0_FBDIV_SHIFT) |
+		       HIWORD_UPDATE(rate->postdiv1, RK3036_PLLCON0_POSTDIV1_MASK,
+					     RK3036_PLLCON0_POSTDIV1_SHIFT),
+		       pll->reg_base + RK3036_PLLCON(0));
+
+	writel_relaxed(HIWORD_UPDATE(rate->refdiv, RK3036_PLLCON1_REFDIV_MASK,
+						   RK3036_PLLCON1_REFDIV_SHIFT) |
+		       HIWORD_UPDATE(rate->postdiv2, RK3036_PLLCON1_POSTDIV2_MASK,
+						     RK3036_PLLCON1_POSTDIV2_SHIFT) |
+		       HIWORD_UPDATE(rate->dsmpd, RK3036_PLLCON1_DSMPD_MASK,
+						  RK3036_PLLCON1_DSMPD_SHIFT),
+		       pll->reg_base + RK3036_PLLCON(1));
+
+	/* GPLL CON2 is not HIWORD_MASK */
+	pllcon = readl_relaxed(pll->reg_base + RK3036_PLLCON(2));
+	pllcon &= ~(RK3036_PLLCON2_FRAC_MASK << RK3036_PLLCON2_FRAC_SHIFT);
+	pllcon |= rate->frac << RK3036_PLLCON2_FRAC_SHIFT;
+	writel_relaxed(pllcon, pll->reg_base + RK3036_PLLCON(2));
+
+	/* wait for the pll to lock */
+	ret = rockchip_pll_wait_lock(pll);
+	if (ret) {
+		pr_warn("%s: pll update unsucessful, trying to restore old params\n",
+			__func__);
+		rockchip_rk3036_pll_set_params(pll, &cur);
+	}
+
+	if (rate_change_remuxed)
+		pll_mux_ops->set_parent(&pll_mux->hw, PLL_MODE_NORM);
+
+	return ret;
+}
+
+static int rockchip_rk3036_pll_set_rate(struct clk_hw *hw, unsigned long drate,
+					unsigned long prate)
+{
+	struct rockchip_clk_pll *pll = to_rockchip_clk_pll(hw);
+	const struct rockchip_pll_rate_table *rate;
+	unsigned long old_rate = rockchip_rk3036_pll_recalc_rate(hw, prate);
+	struct regmap *grf = rockchip_clk_get_grf();
+
+	if (IS_ERR(grf)) {
+		pr_debug("%s: grf regmap not available, aborting rate change\n",
+			 __func__);
+		return PTR_ERR(grf);
+	}
+
+	pr_debug("%s: changing %s from %lu to %lu with a parent rate of %lu\n",
+		 __func__, __clk_get_name(hw->clk), old_rate, drate, prate);
+
+	/* Get required rate settings from table */
+	rate = rockchip_get_pll_settings(pll, drate);
+	if (!rate) {
+		pr_err("%s: Invalid rate : %lu for pll clk %s\n", __func__,
+			drate, __clk_get_name(hw->clk));
+		return -EINVAL;
+	}
+
+	return rockchip_rk3036_pll_set_params(pll, rate);
+}
+
+static int rockchip_rk3036_pll_enable(struct clk_hw *hw)
+{
+	struct rockchip_clk_pll *pll = to_rockchip_clk_pll(hw);
+
+	writel(HIWORD_UPDATE(0, RK3036_PLLCON1_PWRDOWN, 0),
+	       pll->reg_base + RK3036_PLLCON(1));
+
+	return 0;
+}
+
+static void rockchip_rk3036_pll_disable(struct clk_hw *hw)
+{
+	struct rockchip_clk_pll *pll = to_rockchip_clk_pll(hw);
+
+	writel(HIWORD_UPDATE(RK3036_PLLCON1_PWRDOWN,
+			     RK3036_PLLCON1_PWRDOWN, 0),
+	       pll->reg_base + RK3036_PLLCON(1));
+}
+
+static int rockchip_rk3036_pll_is_enabled(struct clk_hw *hw)
+{
+	struct rockchip_clk_pll *pll = to_rockchip_clk_pll(hw);
+	u32 pllcon = readl(pll->reg_base + RK3036_PLLCON(1));
+
+	return !(pllcon & RK3036_PLLCON1_PWRDOWN);
+}
+
+static void rockchip_rk3036_pll_init(struct clk_hw *hw)
+{
+	struct rockchip_clk_pll *pll = to_rockchip_clk_pll(hw);
+	const struct rockchip_pll_rate_table *rate;
+	struct rockchip_pll_rate_table cur;
+	unsigned long drate;
+
+	if (!(pll->flags & ROCKCHIP_PLL_SYNC_RATE))
+		return;
+
+	drate = clk_hw_get_rate(hw);
+	rate = rockchip_get_pll_settings(pll, drate);
+
+	/* when no rate setting for the current rate, rely on clk_set_rate */
+	if (!rate)
+		return;
+
+	rockchip_rk3036_pll_get_params(pll, &cur);
+
+	pr_debug("%s: pll %s@%lu: Hz\n", __func__, __clk_get_name(hw->clk), drate);
+	pr_debug("old - fbdiv: %d, postdiv1: %d, refdiv: %d, postdiv2: %d, dsmpd: %d, frac: %d\n",
+		cur.fbdiv, cur.postdiv1, cur.refdiv, cur.postdiv2, cur.dsmpd, cur.frac);
+	pr_debug("new - fbdiv: %d, postdiv1: %d, refdiv: %d, postdiv2: %d, dsmpd: %d, frac: %d\n",
+		rate->fbdiv, rate->postdiv1, rate->refdiv, rate->postdiv2, rate->dsmpd, rate->frac);
+
+	if (rate->fbdiv != cur.fbdiv || rate->postdiv1 != cur.postdiv1 ||
+		rate->refdiv != cur.refdiv || rate->postdiv2 != cur.postdiv2 ||
+		rate->dsmpd != cur.dsmpd || rate->frac != cur.frac) {
+		struct clk *parent = clk_get_parent(hw->clk);
+
+		if (!parent) {
+			pr_warn("%s: parent of %s not available\n",
+				__func__, __clk_get_name(hw->clk));
+			return;
+		}
+
+		pr_debug("%s: pll %s: rate params do not match rate table, adjusting\n",
+			 __func__, __clk_get_name(hw->clk));
+		rockchip_rk3036_pll_set_params(pll, rate);
+	}
+}
+
+static const struct clk_ops rockchip_rk3036_pll_clk_norate_ops = {
+	.recalc_rate = rockchip_rk3036_pll_recalc_rate,
+	.enable = rockchip_rk3036_pll_enable,
+	.disable = rockchip_rk3036_pll_disable,
+	.is_enabled = rockchip_rk3036_pll_is_enabled,
+};
+
+static const struct clk_ops rockchip_rk3036_pll_clk_ops = {
+	.recalc_rate = rockchip_rk3036_pll_recalc_rate,
+	.round_rate = rockchip_pll_round_rate,
+	.set_rate = rockchip_rk3036_pll_set_rate,
+	.enable = rockchip_rk3036_pll_enable,
+	.disable = rockchip_rk3036_pll_disable,
+	.is_enabled = rockchip_rk3036_pll_is_enabled,
+	.init = rockchip_rk3036_pll_init,
+};
+
+/**
  * PLL used in RK3066, RK3188 and RK3288
  */
 
@@ -376,7 +617,7 @@ struct clk *rockchip_clk_register_pll(enum rockchip_pll_type pll_type,
 	pll_mux->lock = lock;
 	pll_mux->hw.init = &init;
 
-	if (pll_type == pll_rk3066)
+	if (pll_type == pll_rk3036 || pll_type == pll_rk3066)
 		pll_mux->flags |= CLK_MUX_HIWORD_MASK;
 
 	/* the actual muxing is xin24m, pll-output, xin32k */
@@ -421,6 +662,12 @@ struct clk *rockchip_clk_register_pll(enum rockchip_pll_type pll_type,
 	}
 
 	switch (pll_type) {
+	case pll_rk3036:
+		if (!pll->rate_table)
+			init.ops = &rockchip_rk3036_pll_clk_norate_ops;
+		else
+			init.ops = &rockchip_rk3036_pll_clk_ops;
+		break;
 	case pll_rk3066:
 		if (!pll->rate_table)
 			init.ops = &rockchip_rk3066_pll_clk_norate_ops;
diff --git a/drivers/clk/rockchip/clk.h b/drivers/clk/rockchip/clk.h
index dc8ecb2..61e7b2d 100644
--- a/drivers/clk/rockchip/clk.h
+++ b/drivers/clk/rockchip/clk.h
@@ -2,6 +2,9 @@
  * Copyright (c) 2014 MundoReader S.L.
  * Author: Heiko Stuebner <heiko@sntech.de>
  *
+ * Copyright (c) 2015 Rockchip Electronics Co. Ltd.
+ * Author: Xing Zheng <zhengxing@rock-chips.com>
+ *
  * based on
  *
  * samsung/clk.h
@@ -74,9 +77,22 @@ struct clk;
 #define RK3368_EMMC_CON1		0x41c
 
 enum rockchip_pll_type {
+	pll_rk3036,
 	pll_rk3066,
 };
 
+#define RK3036_PLL_RATE(_rate, _refdiv, _fbdiv, _postdiv1,	\
+			_postdiv2, _dsmpd, _frac)		\
+{								\
+	.rate	= _rate##U,					\
+	.fbdiv = _fbdiv,					\
+	.postdiv1 = _postdiv1,					\
+	.refdiv = _refdiv,					\
+	.postdiv2 = _postdiv2,					\
+	.dsmpd = _dsmpd,					\
+	.frac = _frac,						\
+}
+
 #define RK3066_PLL_RATE(_rate, _nr, _nf, _no)	\
 {						\
 	.rate	= _rate##U,			\
@@ -101,6 +117,13 @@ struct rockchip_pll_rate_table {
 	unsigned int nf;
 	unsigned int no;
 	unsigned int nb;
+	/* for RK3036 */
+	unsigned int fbdiv;
+	unsigned int postdiv1;
+	unsigned int refdiv;
+	unsigned int postdiv2;
+	unsigned int dsmpd;
+	unsigned int frac;
 };
 
 /**
-- 
1.7.9.5

[PATCH v7 4/6] clk: rockchip: add clock controller for rk3036

[Xing Zheng]

Add the clock tree definition for the new rk3036 SoC.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
---

Changes in v7: None

 drivers/clk/rockchip/Makefile     |    1 +
 drivers/clk/rockchip/clk-rk3036.c |  478 +++++++++++++++++++++++++++++++++++++
 drivers/clk/rockchip/clk.h        |    9 +-
 3 files changed, 487 insertions(+), 1 deletion(-)
 create mode 100644 drivers/clk/rockchip/clk-rk3036.c

diff --git a/drivers/clk/rockchip/Makefile b/drivers/clk/rockchip/Makefile
index b27edd6..d599829 100644
--- a/drivers/clk/rockchip/Makefile
+++ b/drivers/clk/rockchip/Makefile
@@ -10,6 +10,7 @@ obj-y	+= clk-inverter.o
 obj-y	+= clk-mmc-phase.o
 obj-$(CONFIG_RESET_CONTROLLER)	+= softrst.o
 
+obj-y	+= clk-rk3036.o
 obj-y	+= clk-rk3188.o
 obj-y	+= clk-rk3288.o
 obj-y	+= clk-rk3368.o
diff --git a/drivers/clk/rockchip/clk-rk3036.c b/drivers/clk/rockchip/clk-rk3036.c
new file mode 100644
index 0000000..75553af
--- /dev/null
+++ b/drivers/clk/rockchip/clk-rk3036.c
@@ -0,0 +1,478 @@
+/*
+ * Copyright (c) 2014 MundoReader S.L.
+ * Author: Heiko Stuebner <heiko@sntech.de>
+ *
+ * Copyright (c) 2015 Rockchip Electronics Co. Ltd.
+ * Author: Xing Zheng <zhengxing@rock-chips.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/syscore_ops.h>
+#include <dt-bindings/clock/rk3036-cru.h>
+#include "clk.h"
+
+#define RK3036_GRF_SOC_STATUS0	0x14c
+
+enum rk3036_plls {
+	apll, dpll, gpll,
+};
+
+static struct rockchip_pll_rate_table rk3036_pll_rates[] = {
+	/* _mhz, _refdiv, _fbdiv, _postdiv1, _postdiv2, _dsmpd, _frac */
+	RK3036_PLL_RATE(1608000000, 1, 67, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1584000000, 1, 66, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1560000000, 1, 65, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1536000000, 1, 64, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1512000000, 1, 63, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1488000000, 1, 62, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1464000000, 1, 61, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1440000000, 1, 60, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1416000000, 1, 59, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1392000000, 1, 58, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1368000000, 1, 57, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1344000000, 1, 56, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1320000000, 1, 55, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1296000000, 1, 54, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1272000000, 1, 53, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1248000000, 1, 52, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1200000000, 1, 50, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1188000000, 2, 99, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1104000000, 1, 46, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1100000000, 12, 550, 1, 1, 1, 0),
+	RK3036_PLL_RATE(1008000000, 1, 84, 2, 1, 1, 0),
+	RK3036_PLL_RATE(1000000000, 6, 500, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 984000000, 1, 82, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 960000000, 1, 80, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 936000000, 1, 78, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 912000000, 1, 76, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 900000000, 4, 300, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 888000000, 1, 74, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 864000000, 1, 72, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 840000000, 1, 70, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 816000000, 1, 68, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 800000000, 6, 400, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 700000000, 6, 350, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 696000000, 1, 58, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 600000000, 1, 75, 3, 1, 1, 0),
+	RK3036_PLL_RATE( 594000000, 2, 99, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 504000000, 1, 63, 3, 1, 1, 0),
+	RK3036_PLL_RATE( 500000000, 6, 250, 2, 1, 1, 0),
+	RK3036_PLL_RATE( 408000000, 1, 68, 2, 2, 1, 0),
+	RK3036_PLL_RATE( 312000000, 1, 52, 2, 2, 1, 0),
+	RK3036_PLL_RATE( 216000000, 1, 72, 4, 2, 1, 0),
+	RK3036_PLL_RATE(  96000000, 1, 64, 4, 4, 1, 0),
+	{ /* sentinel */ },
+};
+
+#define RK3036_DIV_CPU_MASK		0x1f
+#define RK3036_DIV_CPU_SHIFT		8
+
+#define RK3036_DIV_PERI_MASK		0xf
+#define RK3036_DIV_PERI_SHIFT		0
+#define RK3036_DIV_ACLK_MASK		0x7
+#define RK3036_DIV_ACLK_SHIFT		4
+#define RK3036_DIV_HCLK_MASK		0x3
+#define RK3036_DIV_HCLK_SHIFT		8
+#define RK3036_DIV_PCLK_MASK		0x7
+#define RK3036_DIV_PCLK_SHIFT		12
+
+#define RK3036_CLKSEL1(_core_periph_div)					\
+	{									\
+		.reg = RK2928_CLKSEL_CON(1),					\
+		.val = HIWORD_UPDATE(_core_periph_div, RK3036_DIV_PERI_MASK,	\
+				RK3036_DIV_PERI_SHIFT)				\
+	}
+
+#define RK3036_CPUCLK_RATE(_prate, _core_periph_div)			\
+	{								\
+		.prate = _prate,					\
+		.divs = {						\
+			RK3036_CLKSEL1(_core_periph_div),		\
+		},							\
+	}
+
+static struct rockchip_cpuclk_rate_table rk3036_cpuclk_rates[] __initdata = {
+	RK3036_CPUCLK_RATE(816000000, 4),
+	RK3036_CPUCLK_RATE(600000000, 4),
+	RK3036_CPUCLK_RATE(312000000, 4),
+};
+
+static const struct rockchip_cpuclk_reg_data rk3036_cpuclk_data = {
+	.core_reg = RK2928_CLKSEL_CON(0),
+	.div_core_shift = 0,
+	.div_core_mask = 0x1f,
+	.mux_core_shift = 7,
+};
+
+PNAME(mux_pll_p)		= { "xin24m", "xin24m" };
+
+PNAME(mux_armclk_p)		= { "apll", "gpll_armclk" };
+PNAME(mux_busclk_p)		= { "apll", "dpll_cpu", "gpll_cpu" };
+PNAME(mux_ddrphy_p)		= { "dpll_ddr", "gpll_ddr" };
+PNAME(mux_pll_src_3plls_p)	= { "apll", "dpll", "gpll" };
+PNAME(mux_timer_p)		= { "xin24m", "pclk_peri_src" };
+
+PNAME(mux_pll_src_apll_dpll_gpll_usb480m_p)	= { "apll", "dpll", "gpll" "usb480m" };
+
+PNAME(mux_mmc_src_p)	= { "apll", "dpll", "gpll", "xin24m" };
+PNAME(mux_i2s_pre_p)	= { "i2s_src", "i2s_frac", "ext_i2s", "xin12m" };
+PNAME(mux_i2s_clkout_p)	= { "i2s_pre", "xin12m" };
+PNAME(mux_spdif_p)	= { "spdif_src", "spdif_frac", "xin12m" };
+PNAME(mux_uart0_p)	= { "uart0_src", "uart0_frac", "xin24m" };
+PNAME(mux_uart1_p)	= { "uart1_src", "uart1_frac", "xin24m" };
+PNAME(mux_uart2_p)	= { "uart2_src", "uart2_frac", "xin24m" };
+PNAME(mux_mac_p)	= { "mac_pll_src", "ext_gmac" };
+PNAME(mux_dclk_p)	= { "dclk_lcdc", "dclk_cru" };
+
+static struct rockchip_pll_clock rk3036_pll_clks[] __initdata = {
+	[apll] = PLL(pll_rk3036, PLL_APLL, "apll", mux_pll_p, 0, RK2928_PLL_CON(0),
+		     RK2928_MODE_CON, 0, 5, 0, rk3036_pll_rates),
+	[dpll] = PLL(pll_rk3036, PLL_DPLL, "dpll", mux_pll_p, 0, RK2928_PLL_CON(4),
+		     RK2928_MODE_CON, 4, 4, 0, NULL),
+	[gpll] = PLL(pll_rk3036, PLL_GPLL, "gpll", mux_pll_p, 0, RK2928_PLL_CON(12),
+		     RK2928_MODE_CON, 12, 6, ROCKCHIP_PLL_SYNC_RATE, rk3036_pll_rates),
+};
+
+#define MFLAGS CLK_MUX_HIWORD_MASK
+#define DFLAGS CLK_DIVIDER_HIWORD_MASK
+#define GFLAGS (CLK_GATE_HIWORD_MASK | CLK_GATE_SET_TO_DISABLE)
+
+static struct rockchip_clk_branch rk3036_clk_branches[] __initdata = {
+	/*
+	 * Clock-Architecture Diagram 1
+	 */
+
+	GATE(0, "gpll_armclk", "gpll", CLK_IGNORE_UNUSED,
+			RK2928_CLKGATE_CON(0), 6, GFLAGS),
+
+	/*
+	 * Clock-Architecture Diagram 2
+	 */
+
+	GATE(0, "dpll_ddr", "dpll", CLK_IGNORE_UNUSED,
+			RK2928_CLKGATE_CON(0), 2, GFLAGS),
+	GATE(0, "gpll_ddr", "gpll", CLK_IGNORE_UNUSED,
+			RK2928_CLKGATE_CON(0), 8, GFLAGS),
+	COMPOSITE_NOGATE(0, "ddrphy2x", mux_ddrphy_p, CLK_IGNORE_UNUSED,
+			RK2928_CLKSEL_CON(26), 8, 1, MFLAGS, 0, 2, DFLAGS | CLK_DIVIDER_POWER_OF_TWO),
+
+	COMPOSITE_NOMUX(0, "pclk_dbg", "armclk", CLK_IGNORE_UNUSED,
+			RK2928_CLKSEL_CON(1), 0, 4, DFLAGS | CLK_DIVIDER_READ_ONLY,
+			RK2928_CLKGATE_CON(0), 7, GFLAGS),
+	COMPOSITE_NOMUX(0, "aclk_core_pre", "armclk", CLK_IGNORE_UNUSED,
+			RK2928_CLKSEL_CON(1), 4, 3, DFLAGS | CLK_DIVIDER_READ_ONLY,
+			RK2928_CLKGATE_CON(0), 7, GFLAGS),
+
+	GATE(0, "dpll_cpu", "dpll", 0, RK2928_CLKGATE_CON(10), 8, GFLAGS),
+	GATE(0, "gpll_cpu", "gpll", 0, RK2928_CLKGATE_CON(0), 1, GFLAGS),
+	COMPOSITE_NOGATE(0, "aclk_cpu_src", mux_busclk_p, 0,
+			RK2928_CLKSEL_CON(0), 14, 2, MFLAGS, 8, 5, DFLAGS),
+	GATE(ACLK_CPU, "aclk_cpu", "aclk_cpu_src", CLK_IGNORE_UNUSED,
+			RK2928_CLKGATE_CON(0), 3, GFLAGS),
+	COMPOSITE_NOMUX(PCLK_CPU, "pclk_cpu", "aclk_cpu_src", CLK_IGNORE_UNUSED,
+			RK2928_CLKSEL_CON(1), 12, 3, DFLAGS | CLK_DIVIDER_READ_ONLY,
+			RK2928_CLKGATE_CON(0), 5, GFLAGS),
+	COMPOSITE_NOMUX(HCLK_CPU, "hclk_cpu", "aclk_cpu_src", CLK_IGNORE_UNUSED,
+			RK2928_CLKSEL_CON(1), 8, 2, DFLAGS | CLK_DIVIDER_READ_ONLY,
+			RK2928_CLKGATE_CON(0), 4, GFLAGS),
+
+	COMPOSITE(0, "aclk_peri_src", mux_pll_src_3plls_p, 0,
+			RK2928_CLKSEL_CON(10), 14, 2, MFLAGS, 0, 5, DFLAGS,
+			RK2928_CLKGATE_CON(2), 0, GFLAGS),
+
+	GATE(ACLK_PERI, "aclk_peri", "aclk_peri_src", 0,
+			RK2928_CLKGATE_CON(2), 1, GFLAGS),
+	DIV(0, "pclk_peri_src", "aclk_peri_src", CLK_IGNORE_UNUSED,
+			RK2928_CLKSEL_CON(10), 12, 2, DFLAGS | CLK_DIVIDER_POWER_OF_TWO),
+	GATE(PCLK_PERI, "pclk_peri", "pclk_peri_src", 0,
+			RK2928_CLKGATE_CON(2), 3, GFLAGS),
+	DIV(0, "hclk_peri_src", "aclk_peri_src", CLK_IGNORE_UNUSED,
+			RK2928_CLKSEL_CON(10), 8, 2, DFLAGS | CLK_DIVIDER_POWER_OF_TWO),
+	GATE(HCLK_PERI, "hclk_peri", "hclk_peri_src", 0,
+			RK2928_CLKGATE_CON(2), 2, GFLAGS),
+
+	COMPOSITE_NODIV(SCLK_TIMER0, "sclk_timer0", mux_timer_p, CLK_IGNORE_UNUSED,
+			RK2928_CLKSEL_CON(2), 4, 1, DFLAGS,
+			RK2928_CLKGATE_CON(1), 0, GFLAGS),
+	COMPOSITE_NODIV(SCLK_TIMER1, "sclk_timer1", mux_timer_p, CLK_IGNORE_UNUSED,
+			RK2928_CLKSEL_CON(2), 5, 1, DFLAGS,
+			RK2928_CLKGATE_CON(1), 1, GFLAGS),
+	COMPOSITE_NODIV(SCLK_TIMER2, "sclk_timer2", mux_timer_p, CLK_IGNORE_UNUSED,
+			RK2928_CLKSEL_CON(2), 6, 1, DFLAGS,
+			RK2928_CLKGATE_CON(2), 4, GFLAGS),
+	COMPOSITE_NODIV(SCLK_TIMER3, "sclk_timer3", mux_timer_p, CLK_IGNORE_UNUSED,
+			RK2928_CLKSEL_CON(2), 7, 1, DFLAGS,
+			RK2928_CLKGATE_CON(2), 5, GFLAGS),
+
+	MUX(0, "uart_pll_clk", mux_pll_src_apll_dpll_gpll_usb480m_p, 0,
+			RK2928_CLKSEL_CON(13), 10, 2, MFLAGS),
+	COMPOSITE_NOMUX(0, "uart0_src", "uart_pll_clk", 0,
+			RK2928_CLKSEL_CON(13), 0, 7, DFLAGS,
+			RK2928_CLKGATE_CON(1), 8, GFLAGS),
+	COMPOSITE_NOMUX(0, "uart1_src", "uart_pll_clk", 0,
+			RK2928_CLKSEL_CON(13), 0, 7, DFLAGS,
+			RK2928_CLKGATE_CON(1), 8, GFLAGS),
+	COMPOSITE_NOMUX(0, "uart2_src", "uart_pll_clk", 0,
+			RK2928_CLKSEL_CON(13), 0, 7, DFLAGS,
+			RK2928_CLKGATE_CON(1), 8, GFLAGS),
+	COMPOSITE_FRAC(0, "uart0_frac", "uart0_src", CLK_SET_RATE_PARENT,
+			RK2928_CLKSEL_CON(17), 0,
+			RK2928_CLKGATE_CON(1), 9, GFLAGS),
+	COMPOSITE_FRAC(0, "uart1_frac", "uart1_src", CLK_SET_RATE_PARENT,
+			RK2928_CLKSEL_CON(18), 0,
+			RK2928_CLKGATE_CON(1), 11, GFLAGS),
+	COMPOSITE_FRAC(0, "uart2_frac", "uart2_src", CLK_SET_RATE_PARENT,
+			RK2928_CLKSEL_CON(19), 0,
+			RK2928_CLKGATE_CON(1), 13, GFLAGS),
+	MUX(SCLK_UART0, "sclk_uart0", mux_uart0_p, CLK_SET_RATE_PARENT,
+			RK2928_CLKSEL_CON(13), 8, 2, MFLAGS),
+	MUX(SCLK_UART1, "sclk_uart1", mux_uart1_p, CLK_SET_RATE_PARENT,
+			RK2928_CLKSEL_CON(14), 8, 2, MFLAGS),
+	MUX(SCLK_UART2, "sclk_uart2", mux_uart2_p, CLK_SET_RATE_PARENT,
+			RK2928_CLKSEL_CON(15), 8, 2, MFLAGS),
+
+	COMPOSITE(0, "aclk_vcodec", mux_pll_src_3plls_p, 0,
+			RK2928_CLKSEL_CON(32), 14, 2, MFLAGS, 8, 5, DFLAGS,
+			RK2928_CLKGATE_CON(3), 11, GFLAGS),
+
+	COMPOSITE(0, "aclk_hvec", mux_pll_src_3plls_p, 0,
+			RK2928_CLKSEL_CON(20), 0, 2, MFLAGS, 2, 5, DFLAGS,
+			RK2928_CLKGATE_CON(10), 6, GFLAGS),
+
+	COMPOSITE(0, "aclk_disp1_pre", mux_pll_src_3plls_p, 0,
+			RK2928_CLKSEL_CON(31), 14, 2, MFLAGS, 8, 5, DFLAGS,
+			RK2928_CLKGATE_CON(1), 4, GFLAGS),
+	COMPOSITE(0, "hclk_disp_pre", mux_pll_src_3plls_p, 0,
+			RK2928_CLKSEL_CON(30), 14, 2, MFLAGS, 8, 5, DFLAGS,
+			RK2928_CLKGATE_CON(0), 11, GFLAGS),
+	COMPOSITE(SCLK_LCDC, "dclk_lcdc", mux_pll_src_3plls_p, 0,
+			RK2928_CLKSEL_CON(28), 0, 2, MFLAGS, 8, 8, DFLAGS,
+			RK2928_CLKGATE_CON(3), 2, GFLAGS),
+
+	COMPOSITE_NODIV(0, "sclk_sdmmc_src", mux_mmc_src_p, 0,
+			RK2928_CLKSEL_CON(12), 8, 2, DFLAGS,
+			RK2928_CLKGATE_CON(2), 11, GFLAGS),
+	DIV(SCLK_SDMMC, "sclk_sdmmc", "sclk_sdmmc_src", 0,
+			RK2928_CLKSEL_CON(11), 0, 7, DFLAGS),
+
+	COMPOSITE_NODIV(0, "sclk_sdio_src", mux_mmc_src_p, 0,
+			RK2928_CLKSEL_CON(12), 10, 2, DFLAGS,
+			RK2928_CLKGATE_CON(2), 13, GFLAGS),
+	DIV(SCLK_SDIO, "sclk_sdio", "sclk_sdio_src", 0,
+			RK2928_CLKSEL_CON(11), 8, 7, DFLAGS),
+
+	COMPOSITE(SCLK_EMMC, "sclk_emmc", mux_mmc_src_p, 0,
+			RK2928_CLKSEL_CON(12), 12, 2, MFLAGS, 0, 7, DFLAGS,
+			RK2928_CLKGATE_CON(2), 14, GFLAGS),
+
+	MMC(SCLK_SDMMC_DRV,    "sdmmc_drv",    "sclk_sdmmc", RK3036_SDMMC_CON0, 1),
+	MMC(SCLK_SDMMC_SAMPLE, "sdmmc_sample", "sclk_sdmmc", RK3036_SDMMC_CON1, 0),
+
+	MMC(SCLK_SDIO_DRV,     "sdio_drv",     "sclk_sdio",  RK3036_SDIO_CON0, 1),
+	MMC(SCLK_SDIO_SAMPLE,  "sdio_sample",  "sclk_sdio",  RK3036_SDIO_CON1, 0),
+
+	MMC(SCLK_EMMC_DRV,     "emmc_drv",     "sclk_emmc",  RK3036_EMMC_CON0,  1),
+	MMC(SCLK_EMMC_SAMPLE,  "emmc_sample",  "sclk_emmc",  RK3036_EMMC_CON1,  0),
+
+	COMPOSITE(0, "i2s_src", mux_pll_src_3plls_p, 0,
+			RK2928_CLKSEL_CON(3), 14, 2, MFLAGS, 0, 7, DFLAGS,
+			RK2928_CLKGATE_CON(0), 9, GFLAGS),
+	COMPOSITE_FRAC(0, "i2s_frac", "i2s_src", CLK_SET_RATE_PARENT,
+			RK2928_CLKSEL_CON(7), 0,
+			RK2928_CLKGATE_CON(0), 10, GFLAGS),
+	MUX(0, "i2s_pre", mux_i2s_pre_p, CLK_SET_RATE_PARENT,
+			RK2928_CLKSEL_CON(3), 8, 2, MFLAGS),
+	COMPOSITE_NODIV(SCLK_I2S_OUT, "i2s_clkout", mux_i2s_clkout_p, 0,
+			RK2928_CLKSEL_CON(3), 12, 1, MFLAGS,
+			RK2928_CLKGATE_CON(0), 13, GFLAGS),
+	GATE(SCLK_I2S, "sclk_i2s", "i2s_pre", CLK_SET_RATE_PARENT,
+			RK2928_CLKGATE_CON(0), 14, GFLAGS),
+
+	COMPOSITE(0, "spdif_src", mux_pll_src_3plls_p, 0,
+			RK2928_CLKSEL_CON(5), 10, 2, MFLAGS, 0, 7, DFLAGS,
+			RK2928_CLKGATE_CON(2), 10, GFLAGS),
+	COMPOSITE_FRAC(0, "spdif_frac", "spdif_src", 0,
+			RK2928_CLKSEL_CON(9), 0,
+			RK2928_CLKGATE_CON(2), 12, GFLAGS),
+	MUX(SCLK_SPDIF, "sclk_spdif", mux_spdif_p, 0,
+			RK2928_CLKSEL_CON(5), 8, 2, MFLAGS),
+
+	GATE(SCLK_OTGPHY0, "sclk_otgphy0", "xin12m", CLK_IGNORE_UNUSED,
+			RK2928_CLKGATE_CON(1), 5, GFLAGS),
+
+	COMPOSITE(SCLK_GPU, "sclk_gpu", mux_pll_src_3plls_p, 0,
+			RK2928_CLKSEL_CON(34), 8, 2, MFLAGS, 0, 5, DFLAGS,
+			RK2928_CLKGATE_CON(3), 13, GFLAGS),
+
+	COMPOSITE(SCLK_SPI, "sclk_spi", mux_pll_src_3plls_p, 0,
+			RK2928_CLKSEL_CON(25), 8, 2, MFLAGS, 0, 7, DFLAGS,
+			RK2928_CLKGATE_CON(2), 9, GFLAGS),
+
+	COMPOSITE(SCLK_NANDC, "sclk_nandc", mux_pll_src_3plls_p, 0,
+			RK2928_CLKSEL_CON(16), 8, 2, MFLAGS, 10, 5, DFLAGS,
+			RK2928_CLKGATE_CON(10), 4, GFLAGS),
+
+	COMPOSITE(SCLK_SFC, "sclk_sfc", mux_pll_src_apll_dpll_gpll_usb480m_p, 0,
+			RK2928_CLKSEL_CON(16), 0, 2, MFLAGS, 2, 5, DFLAGS,
+			RK2928_CLKGATE_CON(10), 5, GFLAGS),
+
+	COMPOSITE_NOGATE(0, "mac_pll_src", mux_pll_src_3plls_p, 0,
+			RK2928_CLKSEL_CON(21), 0, 2, MFLAGS, 4, 5, DFLAGS),
+	MUX(SCLK_MACREF, "mac_clk_ref", mux_mac_p, CLK_SET_RATE_PARENT,
+			RK2928_CLKSEL_CON(21), 3, 1, MFLAGS),
+
+	COMPOSITE_NOMUX(SCLK_MAC, "mac_clk", "mac_clk_ref", 0,
+			RK2928_CLKSEL_CON(21), 9, 5, DFLAGS,
+			RK2928_CLKGATE_CON(2), 6, GFLAGS),
+
+	MUX(SCLK_HDMI, "dclk_hdmi", mux_dclk_p, 0,
+			RK2928_CLKSEL_CON(31), 0, 1, MFLAGS),
+
+	/*
+	 * Clock-Architecture Diagram 3
+	 */
+
+	/* aclk_cpu gates */
+	GATE(0, "sclk_intmem", "aclk_cpu", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(4), 12, GFLAGS),
+	GATE(0, "aclk_strc_sys", "aclk_cpu", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(4), 10, GFLAGS),
+
+	/* hclk_cpu gates */
+	GATE(HCLK_ROM, "hclk_rom", "hclk_cpu", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(5), 6, GFLAGS),
+
+	/* pclk_cpu gates */
+	GATE(PCLK_GRF, "pclk_grf", "pclk_cpu", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(5), 4, GFLAGS),
+	GATE(PCLK_DDRUPCTL, "pclk_ddrupctl", "pclk_cpu", 0, RK2928_CLKGATE_CON(5), 7, GFLAGS),
+	GATE(PCLK_ACODEC, "pclk_acodec", "pclk_cpu", 0, RK2928_CLKGATE_CON(5), 14, GFLAGS),
+	GATE(PCLK_HDMI, "pclk_hdmi", "pclk_cpu", 0, RK2928_CLKGATE_CON(3), 8, GFLAGS),
+
+	/* aclk_vio gates */
+	GATE(ACLK_VIO, "aclk_vio", "aclk_disp1_pre", 0, RK2928_CLKGATE_CON(6), 13, GFLAGS),
+	GATE(ACLK_LCDC, "aclk_lcdc", "aclk_disp1_pre", 0, RK2928_CLKGATE_CON(9), 6, GFLAGS),
+
+	GATE(HCLK_VIO_BUS, "hclk_vio_bus", "hclk_disp_pre", 0, RK2928_CLKGATE_CON(6), 12, GFLAGS),
+	GATE(HCLK_LCDC, "hclk_lcdc", "hclk_disp_pre", 0, RK2928_CLKGATE_CON(9), 5, GFLAGS),
+
+	/* hclk_video gates */
+	GATE(HCLK_VCODEC, "hclk_vcodec", "hclk_disp_pre", 0, RK2928_CLKGATE_CON(3), 12, GFLAGS),
+
+	/* xin24m gates */
+	GATE(SCLK_PVTM_CORE, "sclk_pvtm_core", "xin24m", 0, RK2928_CLKGATE_CON(10), 0, GFLAGS),
+	GATE(SCLK_PVTM_GPU, "sclk_pvtm_gpu", "xin24m", 0, RK2928_CLKGATE_CON(10), 1, GFLAGS),
+
+	/* aclk_peri gates */
+	GATE(0, "aclk_peri_axi_matrix", "aclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(4), 3, GFLAGS),
+	GATE(0, "aclk_cpu_peri", "aclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(4), 2, GFLAGS),
+	GATE(ACLK_DMAC2, "aclk_dmac2", "aclk_peri", 0, RK2928_CLKGATE_CON(5), 1, GFLAGS),
+	GATE(0, "aclk_peri_niu", "aclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(9), 15, GFLAGS),
+
+	/* hclk_peri gates */
+	GATE(0, "hclk_peri_matrix", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(4), 0, GFLAGS),
+	GATE(0, "hclk_usb_peri", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(9), 13, GFLAGS),
+	GATE(0, "hclk_peri_arbi", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(9), 14, GFLAGS),
+	GATE(HCLK_NANDC, "hclk_nandc", "hclk_peri", 0, RK2928_CLKGATE_CON(5), 9, GFLAGS),
+	GATE(HCLK_SDMMC, "hclk_sdmmc", "hclk_peri", 0, RK2928_CLKGATE_CON(5), 10, GFLAGS),
+	GATE(HCLK_SDIO, "hclk_sdio", "hclk_peri", 0, RK2928_CLKGATE_CON(5), 11, GFLAGS),
+	GATE(HCLK_EMMC, "hclk_emmc", "hclk_peri", 0, RK2928_CLKGATE_CON(7), 0, GFLAGS),
+	GATE(HCLK_OTG0, "hclk_otg0", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(5), 13, GFLAGS),
+	GATE(HCLK_OTG1, "hclk_otg1", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(7), 3, GFLAGS),
+	GATE(HCLK_I2S, "hclk_i2s", "hclk_peri", 0, RK2928_CLKGATE_CON(7), 2, GFLAGS),
+	GATE(0, "hclk_sfc", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(3), 14, GFLAGS),
+	GATE(0, "hclk_mac", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(3), 15, GFLAGS),
+
+	/* pclk_peri gates */
+	GATE(0, "pclk_peri_matrix", "pclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(4), 1, GFLAGS),
+	GATE(0, "pclk_efuse", "pclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(5), 2, GFLAGS),
+	GATE(PCLK_TIMER, "pclk_timer", "pclk_peri", 0, RK2928_CLKGATE_CON(7), 7, GFLAGS),
+	GATE(PCLK_PWM, "pclk_pwm", "pclk_peri", 0, RK2928_CLKGATE_CON(7), 10, GFLAGS),
+	GATE(PCLK_SPI, "pclk_spi", "pclk_peri", 0, RK2928_CLKGATE_CON(7), 12, GFLAGS),
+	GATE(PCLK_WDT, "pclk_wdt", "pclk_peri", 0, RK2928_CLKGATE_CON(7), 15, GFLAGS),
+	GATE(PCLK_UART0, "pclk_uart0", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 0, GFLAGS),
+	GATE(PCLK_UART1, "pclk_uart1", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 1, GFLAGS),
+	GATE(PCLK_UART2, "pclk_uart2", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 2, GFLAGS),
+	GATE(PCLK_I2C0, "pclk_i2c0", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 4, GFLAGS),
+	GATE(PCLK_I2C1, "pclk_i2c1", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 5, GFLAGS),
+	GATE(PCLK_I2C2, "pclk_i2c2", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 6, GFLAGS),
+	GATE(PCLK_GPIO0, "pclk_gpio0", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 9, GFLAGS),
+	GATE(PCLK_GPIO1, "pclk_gpio1", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 10, GFLAGS),
+	GATE(PCLK_GPIO2, "pclk_gpio2", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 11, GFLAGS),
+};
+
+static const char *const rk3036_critical_clocks[] __initconst = {
+	"aclk_cpu",
+	"aclk_peri",
+	"hclk_peri",
+	"pclk_peri",
+};
+
+static void __init rk3036_clk_init(struct device_node *np)
+{
+	void __iomem *reg_base;
+	struct clk *clk;
+
+	reg_base = of_iomap(np, 0);
+	if (!reg_base) {
+		pr_err("%s: could not map cru region\n", __func__);
+		return;
+	}
+
+	rockchip_clk_init(np, reg_base, CLK_NR_CLKS);
+
+	/* xin12m is created by an cru-internal divider */
+	clk = clk_register_fixed_factor(NULL, "xin12m", "xin24m", 0, 1, 2);
+	if (IS_ERR(clk))
+		pr_warn("%s: could not register clock xin12m: %ld\n",
+			__func__, PTR_ERR(clk));
+
+	clk = clk_register_fixed_factor(NULL, "usb480m", "xin24m", 0, 20, 1);
+	if (IS_ERR(clk))
+		pr_warn("%s: could not register clock usb480m: %ld\n",
+			__func__, PTR_ERR(clk));
+
+	clk = clk_register_fixed_factor(NULL, "ddrphy", "ddrphy2x", 0, 1, 2);
+	if (IS_ERR(clk))
+		pr_warn("%s: could not register clock ddrphy: %ld\n",
+			__func__, PTR_ERR(clk));
+
+	clk = clk_register_fixed_factor(NULL, "hclk_vcodec_pre",
+					"aclk_vcodec", 0, 1, 4);
+	if (IS_ERR(clk))
+		pr_warn("%s: could not register clock hclk_vcodec_pre: %ld\n",
+			__func__, PTR_ERR(clk));
+
+	clk = clk_register_fixed_factor(NULL, "sclk_macref_out",
+					"hclk_peri_src", 0, 1, 2);
+	if (IS_ERR(clk))
+		pr_warn("%s: could not register clock sclk_macref_out: %ld\n",
+			__func__, PTR_ERR(clk));
+
+	rockchip_clk_register_plls(rk3036_pll_clks,
+				   ARRAY_SIZE(rk3036_pll_clks),
+				   RK3036_GRF_SOC_STATUS0);
+	rockchip_clk_register_branches(rk3036_clk_branches,
+				  ARRAY_SIZE(rk3036_clk_branches));
+	rockchip_clk_protect_critical(rk3036_critical_clocks,
+				      ARRAY_SIZE(rk3036_critical_clocks));
+
+	rockchip_clk_register_armclk(ARMCLK, "armclk",
+			mux_armclk_p, ARRAY_SIZE(mux_armclk_p),
+			&rk3036_cpuclk_data, rk3036_cpuclk_rates,
+			ARRAY_SIZE(rk3036_cpuclk_rates));
+
+	rockchip_register_softrst(np, 9, reg_base + RK2928_SOFTRST_CON(0),
+				  ROCKCHIP_SOFTRST_HIWORD_MASK);
+
+	rockchip_register_restart_notifier(RK2928_GLB_SRST_FST);
+}
+CLK_OF_DECLARE(rk3036_cru, "rockchip,rk3036-cru", rk3036_clk_init);
diff --git a/drivers/clk/rockchip/clk.h b/drivers/clk/rockchip/clk.h
index 61e7b2d..8d8f942 100644
--- a/drivers/clk/rockchip/clk.h
+++ b/drivers/clk/rockchip/clk.h
@@ -33,7 +33,7 @@ struct clk;
 #define HIWORD_UPDATE(val, mask, shift) \
 		((val) << (shift) | (mask) << ((shift) + 16))
 
-/* register positions shared by RK2928, RK3066 and RK3188 */
+/* register positions shared by RK2928, RK3036, RK3066 and RK3188 */
 #define RK2928_PLL_CON(x)		((x) * 0x4)
 #define RK2928_MODE_CON		0x40
 #define RK2928_CLKSEL_CON(x)	((x) * 0x4 + 0x44)
@@ -43,6 +43,13 @@ struct clk;
 #define RK2928_SOFTRST_CON(x)	((x) * 0x4 + 0x110)
 #define RK2928_MISC_CON		0x134
 
+#define RK3036_SDMMC_CON0		0x144
+#define RK3036_SDMMC_CON1		0x148
+#define RK3036_SDIO_CON0		0x14c
+#define RK3036_SDIO_CON1		0x150
+#define RK3036_EMMC_CON0		0x154
+#define RK3036_EMMC_CON1		0x158
+
 #define RK3288_PLL_CON(x)		RK2928_PLL_CON(x)
 #define RK3288_MODE_CON			0x50
 #define RK3288_CLKSEL_CON(x)		((x) * 0x4 + 0x60)
-- 
1.7.9.5

[PATCH v7 5/6] ARM: dts: rockchip: add core rk3036 dts

[Xing Zheng]

Initial release for rk3036, node definitions rk3036 sdk board.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
---

Changes in v7: None

 arch/arm/boot/dts/Makefile       |    1 +
 arch/arm/boot/dts/rk3036-evb.dts |   64 +++++
 arch/arm/boot/dts/rk3036.dtsi    |  547 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 612 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3036-evb.dts
 create mode 100644 arch/arm/boot/dts/rk3036.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 30bbc37..87c8752 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -512,6 +512,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 dtb-$(CONFIG_ARCH_REALVIEW) += \
 	arm-realview-pb1176.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += \
+	rk3036-evb.dtb \
 	rk3066a-bqcurie2.dtb \
 	rk3066a-marsboard.dtb \
 	rk3066a-rayeager.dtb \
diff --git a/arch/arm/boot/dts/rk3036-evb.dts b/arch/arm/boot/dts/rk3036-evb.dts
new file mode 100644
index 0000000..28a0336
--- /dev/null
+++ b/arch/arm/boot/dts/rk3036-evb.dts
@@ -0,0 +1,64 @@
+/*
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *  Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "rk3036.dtsi"
+
+/ {
+	model = "Rockchip RK3036 Evaluation board";
+	compatible = "rockchip,rk3036-evb", "rockchip,rk3036";
+};
+
+&i2c1 {
+	status = "okay";
+
+	hym8563: hym8563@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xin32k";
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/rk3036.dtsi b/arch/arm/boot/dts/rk3036.dtsi
new file mode 100644
index 0000000..380fe10
--- /dev/null
+++ b/arch/arm/boot/dts/rk3036.dtsi
@@ -0,0 +1,547 @@
+/*
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/clock/rk3036-cru.h>
+#include "skeleton.dtsi"
+
+/ {
+	compatible = "rockchip,rk3036";
+
+	interrupt-parent = <&gic>;
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		mshc0 = &emmc;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x60000000 0x40000000>;
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@f00 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf00>;
+			operating-points = <
+				/* KHz    uV */
+				 816000 1000000
+			>;
+			clock-latency = <40000>;
+			clocks = <&cru ARMCLK>;
+			resets = <&cru SRST_CORE0>;
+		};
+		cpu1: cpu@f01 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf01>;
+			resets = <&cru SRST_CORE1>;
+		};
+	};
+
+	amba {
+		compatible = "arm,amba-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		pdma: pdma@20078000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x20078000 0x4000>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&cru ACLK_DMAC2>;
+			clock-names = "apb_pclk";
+		};
+	};
+
+	xin24m: oscillator {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "xin24m";
+		#clock-cells = <0>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		arm,cpu-registers-not-fw-configured;
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		clock-frequency = <24000000>;
+	};
+
+	timer: timer@20044000 {
+		compatible = "rockchip,rk3036-timer", "rockchip,rk3288-timer";
+		reg = <0x20044000 0x20>;
+		interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&xin24m>, <&cru PCLK_TIMER>;
+		clock-names = "timer", "pclk";
+	};
+
+	gic: interrupt-controller@10139000 {
+		compatible = "arm,gic-400";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+
+		reg = <0x10139000 0x1000>,
+		      <0x1013a000 0x1000>,
+		      <0x1013c000 0x2000>,
+		      <0x1013e000 0x2000>;
+		interrupts = <GIC_PPI 9 0xf04>;
+	};
+
+	bus_intmem@10080000 {
+		compatible = "mmio-sram";
+		reg = <0x10080000 0x2000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x10080000 0x2000>;
+	};
+
+	cru: clock-controller@20000000 {
+		compatible = "rockchip,rk3036-cru";
+		reg = <0x20000000 0x1000>;
+		rockchip,grf = <&grf>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+		assigned-clocks = <&cru PLL_GPLL>;
+		assigned-clock-rates = <594000000>;
+	};
+
+	grf: syscon@20008000 {
+		compatible = "rockchip,rk3036-grf", "syscon";
+		reg = <0x20008000 0x1000>;
+	};
+
+	pwm0: pwm@20050000 {
+		compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm";
+		reg = <0x20050000 0x10>;
+		#pwm-cells = <3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm0_pin>;
+		clocks = <&cru PCLK_PWM>;
+		clock-names = "pwm";
+		status = "disabled";
+	};
+
+	pwm1: pwm@20050010 {
+		compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm";
+		reg = <0x20050010 0x10>;
+		#pwm-cells = <3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm1_pin>;
+		clocks = <&cru PCLK_PWM>;
+		clock-names = "pwm";
+		status = "disabled";
+	};
+
+	pwm2: pwm@20050020 {
+		compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm";
+		reg = <0x20050020 0x10>;
+		#pwm-cells = <3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm2_pin>;
+		clocks = <&cru PCLK_PWM>;
+		clock-names = "pwm";
+		status = "disabled";
+	};
+
+	pwm3: pwm@20050030 {
+		compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm";
+		reg = <0x20050030 0x10>;
+		#pwm-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm3_pin>;
+		clocks = <&cru PCLK_PWM>;
+		clock-names = "pwm";
+		status = "disabled";
+	};
+
+	acodec: acodec-ana@20030000 {
+		compatible = "rk3036-codec";
+		reg = <0x20030000 0x4000>;
+		rockchip,grf = <&grf>;
+		clock-names = "acodec_pclk";
+		clocks = <&cru PCLK_ACODEC>;
+		status = "disabled";
+	};
+
+	emmc: dwmmc@1021c000 {
+		compatible = "rockchip,rk3288-dw-mshc";
+		clock-frequency = <37500000>;
+		clock-freq-min-max = <400000 37500000>;
+		clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
+		<&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu_drv", "ciu_sample";
+		dmas = <&pdma 12>;
+		dma-names = "rx-tx";
+		fifo-depth = <0x100>;
+		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x1021c000 0x4000>;
+		broken-cd;
+		bus-width = <8>;
+		cap-mmc-highspeed;
+		mmc-ddr-1_8v;
+		disable-wp;
+		non-removable;
+		num-slots = <1>;
+		default-sample-phase = <158>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+		status = "disabled";
+	};
+
+	i2c0: i2c@20072000 {
+		compatible = "rockchip,rk3288-i2c";
+		reg = <0x20072000 0x1000>;
+		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clock-names = "i2c";
+		clocks = <&cru PCLK_I2C0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c0_xfer>;
+		status = "disabled";
+	};
+
+	i2c1: i2c@20056000 {
+		compatible = "rockchip,rk3288-i2c";
+		reg = <0x20056000 0x1000>;
+		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clock-names = "i2c";
+		clocks = <&cru PCLK_I2C1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c1_xfer>;
+		status = "disabled";
+	};
+
+	i2c2: i2c@2005a000 {
+		compatible = "rockchip,rk3288-i2c";
+		reg = <0x2005a000 0x1000>;
+		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clock-names = "i2c";
+		clocks = <&cru PCLK_I2C2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c2_xfer>;
+		status = "disabled";
+	};
+
+	i2s: i2s@10220000 {
+		compatible = "rockchip,rk3036-i2s", "rockchip,rk3066-i2s";
+		reg = <0x10220000 0x4000>;
+		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		dmas = <&pdma 0>, <&pdma 1>;
+		dma-names = "tx", "rx";
+		clock-names = "i2s_hclk", "i2s_clk";
+		clocks = <&cru HCLK_I2S>, <&cru SCLK_I2S>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s_bus>;
+		status = "disabled";
+	};
+
+	uart0: serial@20060000 {
+		compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart";
+		reg = <0x20060000 0x100>;
+		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
+		clock-names = "baudclk", "apb_pclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+		status = "disabled";
+	};
+
+	uart1: serial@20064000 {
+		compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart";
+		reg = <0x20064000 0x100>;
+		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
+		clock-names = "baudclk", "apb_pclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart1_xfer>;
+		status = "disabled";
+	};
+
+	uart2: serial@20068000 {
+		compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart";
+		reg = <0x20068000 0x100>;
+		interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
+		clock-names = "baudclk", "apb_pclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart2_xfer>;
+		status = "disabled";
+	};
+
+	usb_otg: usb@10180000 {
+		compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb",
+				"snps,dwc2";
+		reg = <0x10180000 0x40000>;
+		interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_OTG0>;
+		clock-names = "otg";
+		dr_mode = "otg";
+		g-np-tx-fifo-size = <16>;
+		g-rx-fifo-size = <275>;
+		g-tx-fifo-size = <256 128 128 64 64 32>;
+		g-use-dma;
+		status = "disabled";
+	};
+
+	usb_host: usb@101c0000 {
+		compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb",
+				"snps,dwc2";
+		reg = <0x101c0000 0x40000>;
+		interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_OTG1>;
+		clock-names = "otg";
+		dr_mode = "host";
+		status = "disabled";
+	};
+
+	pinctrl: pinctrl {
+		compatible = "rockchip,rk3036-pinctrl";
+		rockchip,grf = <&grf>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gpio0: gpio0@2007c000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x2007c000 0x100>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO0>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio1@20080000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x20080000 0x100>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO1>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio2@20084000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x20084000 0x100>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO2>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pcfg_pull_up: pcfg-pull-up {
+			bias-pull-up;
+		};
+
+		pcfg_pull_down: pcfg-pull-down {
+			bias-pull-down;
+		};
+
+		pcfg_pull_none: pcfg-pull-none {
+			bias-disable;
+		};
+
+		pwm0 {
+			pwm0_pin: pwm0-pin {
+				rockchip,pins = <0 0 RK_FUNC_2 &pcfg_pull_none>;
+			};
+		};
+
+		pwm1 {
+			pwm1_pin: pwm1-pin {
+				rockchip,pins = <0 1 RK_FUNC_2 &pcfg_pull_none>;
+			};
+		};
+
+		pwm2 {
+			pwm2_pin: pwm2-pin {
+				rockchip,pins = <0 1 2 &pcfg_pull_none>;
+			};
+		};
+
+		pwm3 {
+			pwm3_pin: pwm3-pin {
+				rockchip,pins = <0 27 1 &pcfg_pull_none>;
+			};
+		};
+
+		emmc {
+			/*
+			 * We run eMMC at max speed; bump up drive strength.
+			 * We also have external pulls, so disable the internal ones.
+			 */
+			emmc_clk: emmc-clk {
+				rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none>;
+			};
+
+			emmc_cmd: emmc-cmd {
+				rockchip,pins = <2 1 RK_FUNC_2 &pcfg_pull_none>;
+			};
+
+			emmc_bus8: emmc-bus8 {
+				rockchip,pins = <1 24 RK_FUNC_2 &pcfg_pull_none>,
+						<1 25 RK_FUNC_2 &pcfg_pull_none>,
+						<1 26 RK_FUNC_2 &pcfg_pull_none>,
+						<1 27 RK_FUNC_2 &pcfg_pull_none>,
+						<1 28 RK_FUNC_2 &pcfg_pull_none>,
+						<1 29 RK_FUNC_2 &pcfg_pull_none>,
+						<1 30 RK_FUNC_2 &pcfg_pull_none>,
+						<1 31 RK_FUNC_2 &pcfg_pull_none>;
+			};
+		};
+
+		i2c0 {
+			i2c0_xfer: i2c0-xfer {
+				rockchip,pins = <0 0 RK_FUNC_1 &pcfg_pull_none>,
+						<0 1 RK_FUNC_1 &pcfg_pull_none>;
+			};
+		};
+
+		i2c1 {
+			i2c1_xfer: i2c1-xfer {
+				rockchip,pins = <0 2 RK_FUNC_1 &pcfg_pull_none>,
+						<0 3 RK_FUNC_1 &pcfg_pull_none>;
+			};
+		};
+
+		i2c2 {
+			i2c2_xfer: i2c2-xfer {
+				rockchip,pins = <2 20 RK_FUNC_1 &pcfg_pull_none>,
+						<2 21 RK_FUNC_1 &pcfg_pull_none>;
+			};
+		};
+
+		i2s {
+			i2s_bus: i2s-bus {
+				rockchip,pins = <1 0 RK_FUNC_1 &pcfg_pull_none>,
+						<1 1 RK_FUNC_1 &pcfg_pull_none>,
+						<1 2 RK_FUNC_1 &pcfg_pull_none>,
+						<1 3 RK_FUNC_1 &pcfg_pull_none>,
+						<1 4 RK_FUNC_1 &pcfg_pull_none>,
+						<1 5 RK_FUNC_1 &pcfg_pull_none>;
+			};
+		};
+
+		uart0 {
+			uart0_xfer: uart0-xfer {
+				rockchip,pins = <0 16 RK_FUNC_1 &pcfg_pull_up>,
+						<0 17 RK_FUNC_1 &pcfg_pull_none>;
+			};
+
+			uart0_cts: uart0-cts {
+				rockchip,pins = <0 18 RK_FUNC_1 &pcfg_pull_up>;
+			};
+
+			uart0_rts: uart0-rts {
+				rockchip,pins = <0 19 RK_FUNC_1 &pcfg_pull_none>;
+			};
+		};
+
+		uart1 {
+			uart1_xfer: uart1-xfer {
+				rockchip,pins = <2 22 RK_FUNC_1 &pcfg_pull_none>,
+						<2 23 RK_FUNC_1 &pcfg_pull_none>;
+			};
+			/* no rts / cts for uart1 */
+		};
+
+		uart2 {
+			uart2_xfer: uart2-xfer {
+				rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_none>,
+						<1 19 RK_FUNC_2 &pcfg_pull_none>;
+			};
+			/* no rts / cts for uart2 */
+		};
+	};
+};
-- 
1.7.9.5

[PATCH v7 6/6] ARM: dts: enable smp for rk3036

[Xing Zheng]

Enable smp for rk3036, and add the smp sram name for adapting.

---

Changes in v7:
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>

 arch/arm/boot/dts/rk3036.dtsi |    5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/rk3036.dtsi b/arch/arm/boot/dts/rk3036.dtsi
index 380fe10..61b40dd 100644
--- a/arch/arm/boot/dts/rk3036.dtsi
+++ b/arch/arm/boot/dts/rk3036.dtsi
@@ -75,6 +75,7 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		enable-method = "rockchip,rk3036-smp";
 
 		cpu0: cpu@f00 {
 			device_type = "cpu";
@@ -157,6 +158,10 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x10080000 0x2000>;
+		smp-sram@0 {
+			compatible = "rockchip,rk3066-smp-sram";
+			reg = <0x00 0x10>;
+		};
 	};
 
 	cru: clock-controller@20000000 {
-- 
1.7.9.5

Re: [PATCH v7 0/6] Build and support rk3036 SoC platform

[Heiko Stübner]

Hi Xing Zheng,

Am Donnerstag, 5. November 2015, 15:33:54 schrieb Xing Zheng:
> Hi,
>   We need to support rk3036 soc platform via upstream, there are
> some primary parts for the initial release of minimum system: dts,
> clk-pll, smp, and clock tree for rk3036, and additional, we can use
> these startup and run to init processs.

[...]

after talking with Mike and agreeing that I'm again taking the regular
clock patches to them, I've applied all of this to appropriate branches.
I did some cosmetics, as explained below.


> Xing Zheng (6):
>   dt-bindings: add documentation of rk3036 clock controller
>   clk: rockchip: add dt-binding header for rk3036
>   clk: rockchip: add new pll-type for rk3036 and similar socs
- wrapped some overly long lines, otherwise this is similar to what
  Stephen already took for the rk3066-pll-type.


>   clk: rockchip: add clock controller for rk3036
>   ARM: dts: rockchip: add core rk3036 dts
- split off the evb into a separate patch
- reordered some nodes (please order by the address (the @xxxxxxxx)
- reordered some properties
- fixed the gic cpu masks


>   ARM: dts: enable smp for rk3036
folded into the core dtsi addition


Please take a final look at [0] to make sure I didn't mess up anything.


Thanks
Heiko


[0]
https://git.kernel.org/cgit/linux/kernel/git/mmind/linux-rockchip.git/log/?h=v4.5-clk/next
https://git.kernel.org/cgit/linux/kernel/git/mmind/linux-rockchip.git/log/?h=v4.5-armsoc/dts32

Re: [PATCH v7 0/6] Build and support rk3036 SoC platform

[Xing Zheng]

OK, Thanks Heiko. :-)

On 2015年11月24日 08:03, Heiko Stübner wrote:
> Hi Xing Zheng,
>
> Am Donnerstag, 5. November 2015, 15:33:54 schrieb Xing Zheng:
>> Hi,
>>    We need to support rk3036 soc platform via upstream, there are
>> some primary parts for the initial release of minimum system: dts,
>> clk-pll, smp, and clock tree for rk3036, and additional, we can use
>> these startup and run to init processs.
> [...]
>
> after talking with Mike and agreeing that I'm again taking the regular
> clock patches to them, I've applied all of this to appropriate branches.
> I did some cosmetics, as explained below.
>
>
>> Xing Zheng (6):
>>    dt-bindings: add documentation of rk3036 clock controller
>>    clk: rockchip: add dt-binding header for rk3036
>>    clk: rockchip: add new pll-type for rk3036 and similar socs
> - wrapped some overly long lines, otherwise this is similar to what
>    Stephen already took for the rk3066-pll-type.
>
>
>>    clk: rockchip: add clock controller for rk3036
>>    ARM: dts: rockchip: add core rk3036 dts
> - split off the evb into a separate patch
> - reordered some nodes (please order by the address (the @xxxxxxxx)
> - reordered some properties
> - fixed the gic cpu masks
>
>
>>    ARM: dts: enable smp for rk3036
> folded into the core dtsi addition
>
>
> Please take a final look at [0] to make sure I didn't mess up anything.
>
>
> Thanks
> Heiko
>
>
> [0]
> https://git.kernel.org/cgit/linux/kernel/git/mmind/linux-rockchip.git/log/?h=v4.5-clk/next
> https://git.kernel.org/cgit/linux/kernel/git/mmind/linux-rockchip.git/log/?h=v4.5-armsoc/dts32
>
>
>