[PATCH v3 00/19] drm: Add Allwinner A10 display engine support

[PATCH v3 00/19] drm: Add Allwinner A10 display engine support

[Maxime Ripard]

Hi everyone,

The Allwinner SoCs (except for the very latest ones) all share the
same set of controllers, loosely coupled together to form the display
pipeline.

Depending on the SoC, the number of instances of the controller will
change (2 instances of each in the A10, only one in the A13, for
example), and the output availables will change too (HDMI, composite,
VGA on the A20, none of them on the A13).

On most featured SoCs, it looks like that:

+--------------------------------------------+
|                    RAM                     |
+--------------------------------------------+
      |            |      |            |
      v            |      |            v
+----------------+ |      | +----------------+
|    Frontend    | |      | |    Frontend    |
+----------------+ |      | +----------------+
        |          |      |         |
        v          |      |         v
+----------------+ |      | +----------------+
|    Backend     |<+      +>|    Backend     |
+----------------+          +----------------+
        |                           |
        v                           v
+----------------+          +----------------+---> LVDS
|      TCON      |          |      TCON      |---> RGB
+----------------+          +----------------+
       |       +---+       +---+          |
       |           |       |              |
       v           v       v              v
+------------+  +------------+  +------------+---> VGA
| TV Encoder |  |    HDMI    |  | TV Encoder |---> Composite
+------------+  +------------+  +------------+

The current code only assumes that there is a single instance of all
the controllers. It also supports only the RGB and Composite
interfaces.

Let me know what you think,
Maxime

Changes from v2:
  - Rebased on top of next-20160318

  - Dropped the generic clock regmap conversion and implemented a
    custom clock for our pixel clock, backed by a regmap
  - Added the reset bits for the tcon channel 0 and display clocks
  - Used the new generic gates compatible for the DRAM gates
  - Few clock fixes (missing iounmap, return error checks, etc)
  - Found out that the TCON channel 1 clock was not operating properly
    because of some weird rounding down and up between the various
    generic clocks involved. Rewrote it using custom operations

  - Removed some TODO that were still there
  - Converted our panel DT description to the OF graph instead of a
    custom property
  - Tested the driver on a setup where U-Boot was not initialising the
    display, or initialising it on a different output, and fixed a
    number of associated bugs (mostly related to missing
    initialisation bits, missing reset handles, and so on)
  - Fixed the layer code that was assuming that the X and Y
    coordinates were in pixels, leading to a miscalculation of the
    buffer address when those coordinates where set.
  - Added the missing EXPORT_SYMBOL calls

  - Fixed our VBLANK interrupt code that was completely broken (and
    not usable, which is why it was unnoticed)

Changes from v1:
  - Rebased on top of 4.4

  - Merged the clock drivers for the display and TCON channel 0 clocks
  - Replaced the container_of calls in the display reset clocks to an
    inline function
  - Checked the return code of of_clk_parent_fill in the clocks
    drivers
  - Checked the return code of of_clk_add_provider in the tcon-ch1 and
    PLL3 clocks
  - Added missing clocks headers
  - Created a composite clock unregister function

  - Moved the binding documentation to
    Documentation/devicetree/bindings/display
  - Added the clocks binding documentation
  - Added the Olimex vendor to the list of DT vendors
  - Moved to the OF graph representation and the component framework

  - Moved the reset cells count check into the reset framework to
    avoid duplicating the code in every xlate implementation.
  - Made the reset_ops const

  - Reworked the DRM cmdline mode parsing code to allow named mode
  - Fixed the TV mode lookup when the mode name is not present (for
    example because it was given by the userspace)

  - Made the driver outputs optional (to avoid crashing when a board
    doesn't have either a panel or a composite output enabled)
  - Added multiple plane support with transparency
  - Moved the backend registers writes commit in the CRTC atomic_flush
    callback
  - Removed the load / unload functions
  - Removed the enabled booleans in my private structure and removed
    the implicit call to disable_unused_functions in the DRM core to
    push it in the drivers.
  - Fixed a few bitmasks on some bitfields definition
  - Fixed the RGB connector mode validation that was not testing the
    right values

Maxime Ripard (19):
  clk: composite: Add unregister function
  clk: sunxi: Add display and TCON0 clocks driver
  clk: sunxi: Add PLL3 clock
  clk: sunxi: Add TCON channel1 clock
  dt-bindings: clk: sun5i: add DRAM gates compatible
  ARM: sun5i: dt: Add pll3 and pll7 clocks
  ARM: sun5i: a13: Add display and TCON clocks
  ARM: sun5i: Add DRAM gates
  ARM: sun5i: Add TV encoder gate to the DTSI
  drm: fb: Add seq_file definition
  drm/panel: simple: Add timings for the Olimex LCD-OLinuXino-4.3TS
  drm: Add Allwinner A10 Display Engine support
  drm: sun4i: Add DT bindings documentation
  drm: sun4i: Add RGB output
  drm: sun4i: Add composite output
  drm: sun4i: tv: Add PAL output standard
  drm: sun4i: tv: Add NTSC output standard
  ARM: sun5i: r8: Add display blocks to the DTSI
  ARM: sun5i: chip: Enable the TV Encoder

 Documentation/devicetree/bindings/clock/sunxi.txt  |   5 +
 .../display/panel/olimex,lcd-olinuxino-43-ts.txt   |   7 +
 .../bindings/display/sunxi/sun4i-drm.txt           | 254 ++++++++
 arch/arm/boot/dts/sun5i-a13.dtsi                   |  66 +-
 arch/arm/boot/dts/sun5i-r8-chip.dts                |  12 +
 arch/arm/boot/dts/sun5i-r8.dtsi                    | 142 ++++-
 arch/arm/boot/dts/sun5i.dtsi                       |  43 ++
 drivers/clk/clk-composite.c                        |  15 +
 drivers/clk/sunxi/Makefile                         |   3 +
 drivers/clk/sunxi/clk-sun4i-display.c              | 262 ++++++++
 drivers/clk/sunxi/clk-sun4i-pll3.c                 |  98 +++
 drivers/clk/sunxi/clk-sun4i-tcon-ch1.c             | 300 +++++++++
 drivers/gpu/drm/Kconfig                            |   2 +
 drivers/gpu/drm/Makefile                           |   3 +-
 drivers/gpu/drm/panel/panel-simple.c               |  26 +
 drivers/gpu/drm/sun4i/Kconfig                      |  14 +
 drivers/gpu/drm/sun4i/Makefile                     |  13 +
 drivers/gpu/drm/sun4i/sun4i_backend.c              | 364 +++++++++++
 drivers/gpu/drm/sun4i/sun4i_backend.h              | 165 +++++
 drivers/gpu/drm/sun4i/sun4i_crtc.c                 | 120 ++++
 drivers/gpu/drm/sun4i/sun4i_crtc.h                 |  30 +
 drivers/gpu/drm/sun4i/sun4i_dotclock.c             | 160 +++++
 drivers/gpu/drm/sun4i/sun4i_dotclock.h             |  21 +
 drivers/gpu/drm/sun4i/sun4i_drv.c                  | 326 ++++++++++
 drivers/gpu/drm/sun4i/sun4i_drv.h                  |  30 +
 drivers/gpu/drm/sun4i/sun4i_framebuffer.c          |  54 ++
 drivers/gpu/drm/sun4i/sun4i_framebuffer.h          |  19 +
 drivers/gpu/drm/sun4i/sun4i_layer.c                | 161 +++++
 drivers/gpu/drm/sun4i/sun4i_layer.h                |  30 +
 drivers/gpu/drm/sun4i/sun4i_rgb.c                  | 234 +++++++
 drivers/gpu/drm/sun4i/sun4i_rgb.h                  |  18 +
 drivers/gpu/drm/sun4i/sun4i_tcon.c                 | 538 ++++++++++++++++
 drivers/gpu/drm/sun4i/sun4i_tcon.h                 | 186 ++++++
 drivers/gpu/drm/sun4i/sun4i_tv.c                   | 708 +++++++++++++++++++++
 include/drm/drm_fb_cma_helper.h                    |   2 +
 include/linux/clk-provider.h                       |   1 +
 36 files changed, 4424 insertions(+), 8 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt
 create mode 100644 Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
 create mode 100644 drivers/clk/sunxi/clk-sun4i-display.c
 create mode 100644 drivers/clk/sunxi/clk-sun4i-pll3.c
 create mode 100644 drivers/clk/sunxi/clk-sun4i-tcon-ch1.c
 create mode 100644 drivers/gpu/drm/sun4i/Kconfig
 create mode 100644 drivers/gpu/drm/sun4i/Makefile
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_backend.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_backend.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_crtc.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_crtc.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_dotclock.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_dotclock.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_drv.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_drv.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_framebuffer.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_framebuffer.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_layer.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_layer.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_rgb.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_rgb.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_tcon.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_tcon.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_tv.c

-- 
2.7.3

[PATCH v3 01/19] clk: composite: Add unregister function

[Maxime Ripard]

The composite clock didn't have any unregistration function, which forced
us to use clk_unregister directly on it.

While it was already not great from an API point of view, it also meant
that we were leaking the clk_composite structure allocated in
clk_register_composite.

Add a clk_unregister_composite function to fix this.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 drivers/clk/clk-composite.c  | 15 +++++++++++++++
 include/linux/clk-provider.h |  1 +
 2 files changed, 16 insertions(+)

diff --git a/drivers/clk/clk-composite.c b/drivers/clk/clk-composite.c
index 1f903e1f86a2..b0f3b84ebd13 100644
--- a/drivers/clk/clk-composite.c
+++ b/drivers/clk/clk-composite.c
@@ -286,3 +286,18 @@ err:
 	kfree(composite);
 	return clk;
 }
+
+void clk_unregister_composite(struct clk *clk)
+{
+	struct clk_composite *composite;
+	struct clk_hw *hw;
+
+	hw = __clk_get_hw(clk);
+	if (!hw)
+		return;
+
+	composite = to_clk_composite(hw);
+
+	clk_unregister(clk);
+	kfree(composite);
+}
diff --git a/include/linux/clk-provider.h b/include/linux/clk-provider.h
index da95258127aa..26a8c9b7be71 100644
--- a/include/linux/clk-provider.h
+++ b/include/linux/clk-provider.h
@@ -603,6 +603,7 @@ struct clk *clk_register_composite(struct device *dev, const char *name,
 		struct clk_hw *rate_hw, const struct clk_ops *rate_ops,
 		struct clk_hw *gate_hw, const struct clk_ops *gate_ops,
 		unsigned long flags);
+void clk_unregister_composite(struct clk *clk);
 
 /***
  * struct clk_gpio_gate - gpio gated clock
-- 
2.7.3

[PATCH v3 02/19] clk: sunxi: Add display and TCON0 clocks driver

[Maxime Ripard]

The A10 SoCs and its relatives has a special clock controller to drive the
display engines (both frontend and backend), that have a lot in common with
the clock to drive the first TCON channel.

Add a driver to support both.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/clock/sunxi.txt |   2 +
 drivers/clk/sunxi/Makefile                        |   1 +
 drivers/clk/sunxi/clk-sun4i-display.c             | 262 ++++++++++++++++++++++
 3 files changed, 265 insertions(+)
 create mode 100644 drivers/clk/sunxi/clk-sun4i-display.c

diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index 834436fbe83d..50e212bc8923 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -64,6 +64,7 @@ Required properties:
 	"allwinner,sun8i-h3-bus-gates-clk" - for the bus gates on H3
 	"allwinner,sun9i-a80-apbs-gates-clk" - for the APBS gates on A80
 	"allwinner,sun4i-a10-dram-gates-clk" - for the DRAM gates on A10
+	"allwinner,sun4i-a10-display-clk" - for the display clocks on the A10
 	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
 	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
 	"allwinner,sun9i-a80-mmc-clk" - for mmc module clocks on A80
@@ -73,6 +74,7 @@ Required properties:
 	"allwinner,sun8i-a23-mbus-clk" - for the MBUS clock on A23
 	"allwinner,sun7i-a20-out-clk" - for the external output clocks
 	"allwinner,sun7i-a20-gmac-clk" - for the GMAC clock module on A20/A31
+	"allwinner,sun4i-a10-tcon-ch0-clk" - for the TCON channel 0 clock on the A10
 	"allwinner,sun4i-a10-usb-clk" - for usb gates + resets on A10 / A20
 	"allwinner,sun5i-a13-usb-clk" - for usb gates + resets on A13
 	"allwinner,sun6i-a31-usb-clk" - for usb gates + resets on A31
diff --git a/drivers/clk/sunxi/Makefile b/drivers/clk/sunxi/Makefile
index 3fd7901d48e4..37a6a642a037 100644
--- a/drivers/clk/sunxi/Makefile
+++ b/drivers/clk/sunxi/Makefile
@@ -11,6 +11,7 @@ obj-y += clk-a10-ve.o
 obj-y += clk-a20-gmac.o
 obj-y += clk-mod0.o
 obj-y += clk-simple-gates.o
+obj-y += clk-sun4i-display.o
 obj-y += clk-sun8i-bus-gates.o
 obj-y += clk-sun8i-mbus.o
 obj-y += clk-sun9i-core.o
diff --git a/drivers/clk/sunxi/clk-sun4i-display.c b/drivers/clk/sunxi/clk-sun4i-display.c
new file mode 100644
index 000000000000..af7d1faebdec
--- /dev/null
+++ b/drivers/clk/sunxi/clk-sun4i-display.c
@@ -0,0 +1,262 @@
+/*
+ * Copyright 2015 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/kernel.h>
+#include <linux/of_address.h>
+#include <linux/reset-controller.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+
+struct sun4i_a10_display_clk_data {
+	bool	has_div;
+	u8	has_rst;
+	u8	parents;
+
+	u8	offset_en;
+	u8	offset_div;
+	u8	offset_mux;
+	u8	offset_rst;
+
+	u8	width_div;
+	u8	width_mux;
+};
+
+struct reset_data {
+	void __iomem			*reg;
+	spinlock_t			*lock;
+	struct reset_controller_dev	rcdev;
+	u8				offset;
+};
+
+static DEFINE_SPINLOCK(sun4i_a10_display_lock);
+
+static inline struct reset_data *rcdev_to_reset_data(struct reset_controller_dev *rcdev)
+{
+	return container_of(rcdev, struct reset_data, rcdev);
+};
+
+static int sun4i_a10_display_assert(struct reset_controller_dev *rcdev,
+				    unsigned long id)
+{
+	struct reset_data *data = rcdev_to_reset_data(rcdev);
+	unsigned long flags;
+	u32 reg;
+
+	spin_lock_irqsave(data->lock, flags);
+
+	reg = readl(data->reg);
+	writel(reg & ~BIT(data->offset + id), data->reg);
+
+	spin_unlock_irqrestore(data->lock, flags);
+
+	return 0;
+}
+
+static int sun4i_a10_display_deassert(struct reset_controller_dev *rcdev,
+				      unsigned long id)
+{
+	struct reset_data *data = rcdev_to_reset_data(rcdev);
+	unsigned long flags;
+	u32 reg;
+
+	spin_lock_irqsave(data->lock, flags);
+
+	reg = readl(data->reg);
+	writel(reg | BIT(data->offset + id), data->reg);
+
+	spin_unlock_irqrestore(data->lock, flags);
+
+	return 0;
+}
+
+static int sun4i_a10_display_status(struct reset_controller_dev *rcdev,
+				    unsigned long id)
+{
+	struct reset_data *data = rcdev_to_reset_data(rcdev);
+
+	return !(readl(data->reg) & BIT(data->offset + id));
+}
+
+static const struct reset_control_ops sun4i_a10_display_reset_ops = {
+	.assert		= sun4i_a10_display_assert,
+	.deassert	= sun4i_a10_display_deassert,
+	.status		= sun4i_a10_display_status,
+};
+
+static int sun4i_a10_display_reset_xlate(struct reset_controller_dev *rcdev,
+					 const struct of_phandle_args *spec)
+{
+	/* We only have a single reset signal */
+	return 0;
+}
+
+static void __init sun4i_a10_display_init(struct device_node *node,
+					  struct sun4i_a10_display_clk_data *data)
+{
+	const char *parents[data->parents];
+	const char *clk_name = node->name;
+	struct reset_data *reset_data;
+	struct clk_divider *div = NULL;
+	struct clk_gate *gate;
+	struct resource res;
+	struct clk_mux *mux;
+	void __iomem *reg;
+	struct clk *clk;
+	int ret;
+
+	of_property_read_string(node, "clock-output-names", &clk_name);
+
+	reg = of_io_request_and_map(node, 0, of_node_full_name(node));
+	if (IS_ERR(reg)) {
+		pr_err("%s: Could not map the clock registers\n", clk_name);
+		return;
+	}
+
+	ret = of_clk_parent_fill(node, parents, data->parents);
+	if (ret != data->parents) {
+		pr_err("%s Could not retrieve the parents\n", clk_name);
+		goto unmap;
+	}
+
+	mux = kzalloc(sizeof(*mux), GFP_KERNEL);
+	if (!mux)
+		goto unmap;
+
+	mux->reg = reg;
+	mux->shift = data->offset_mux;
+	mux->mask = (1 << data->width_mux) - 1;
+	mux->lock = &sun4i_a10_display_lock;
+
+	gate = kzalloc(sizeof(*gate), GFP_KERNEL);
+	if (!gate)
+		goto free_mux;
+
+	gate->reg = reg;
+	gate->bit_idx = data->offset_en;
+	gate->lock = &sun4i_a10_display_lock;
+
+	if (data->has_div) {
+		div = kzalloc(sizeof(*div), GFP_KERNEL);
+		if (!div)
+			goto free_gate;
+
+		div->reg = reg;
+		div->shift = data->offset_div;
+		div->width = data->width_div;
+		div->lock = &sun4i_a10_display_lock;
+	}
+
+	clk = clk_register_composite(NULL, clk_name,
+				     parents, data->parents,
+				     &mux->hw, &clk_mux_ops,
+				     data->has_div ? &div->hw : NULL,
+				     data->has_div ? &clk_divider_ops : NULL,
+				     &gate->hw, &clk_gate_ops,
+				     0);
+	if (IS_ERR(clk)) {
+		pr_err("%s: Couldn't register the clock\n", clk_name);
+		goto free_div;
+	}
+
+	ret = of_clk_add_provider(node, of_clk_src_simple_get, clk);
+	if (ret) {
+		pr_err("%s: Couldn't register DT provider\n", clk_name);
+		goto free_clk;
+	}
+
+	if (!data->has_rst)
+		return;
+
+	reset_data = kzalloc(sizeof(*reset_data), GFP_KERNEL);
+	if (!reset_data)
+		goto free_of_clk;
+
+	reset_data->reg = reg;
+	reset_data->offset = data->offset_rst;
+	reset_data->lock = &sun4i_a10_display_lock;
+	reset_data->rcdev.nr_resets = data->has_rst;
+	reset_data->rcdev.ops = &sun4i_a10_display_reset_ops;
+	reset_data->rcdev.of_node = node;
+
+	if (data->has_rst == 1) {
+		reset_data->rcdev.of_reset_n_cells = 0;
+		reset_data->rcdev.of_xlate = &sun4i_a10_display_reset_xlate;
+	} else {
+		reset_data->rcdev.of_reset_n_cells = 1;
+	}
+
+	if (reset_controller_register(&reset_data->rcdev)) {
+		pr_err("%s: Couldn't register the reset controller\n",
+		       clk_name);
+		goto free_reset;
+	}
+
+	return;
+
+free_reset:
+	kfree(reset_data);
+free_of_clk:
+	of_clk_del_provider(node);
+free_clk:
+	clk_unregister_composite(clk);
+free_div:
+	if (data->has_div)
+		kfree(div);
+free_gate:
+	kfree(gate);
+free_mux:
+	kfree(mux);
+unmap:
+	iounmap(reg);
+	of_address_to_resource(node, 0, &res);
+	release_mem_region(res.start, resource_size(&res));
+}
+
+static struct sun4i_a10_display_clk_data sun4i_a10_tcon_ch0_data = {
+	.has_rst	= 2,
+	.parents	= 4,
+	.offset_en	= 31,
+	.offset_rst	= 29,
+	.offset_mux	= 24,
+	.width_mux	= 2,
+};
+
+static void __init sun4i_a10_tcon_ch0_setup(struct device_node *node)
+{
+	sun4i_a10_display_init(node, &sun4i_a10_tcon_ch0_data);
+}
+CLK_OF_DECLARE(sun4i_a10_tcon_ch0, "allwinner,sun4i-a10-tcon-ch0-clk",
+	       sun4i_a10_tcon_ch0_setup);
+
+static struct sun4i_a10_display_clk_data sun4i_a10_display_data = {
+	.has_div	= true,
+	.has_rst	= 1,
+	.parents	= 3,
+	.offset_en	= 31,
+	.offset_rst	= 30,
+	.offset_mux	= 24,
+	.offset_div	= 0,
+	.width_mux	= 2,
+	.width_div	= 4,
+};
+
+static void __init sun4i_a10_display_setup(struct device_node *node)
+{
+	sun4i_a10_display_init(node, &sun4i_a10_display_data);
+}
+CLK_OF_DECLARE(sun4i_a10_display, "allwinner,sun4i-a10-display-clk",
+	       sun4i_a10_display_setup);
-- 
2.7.3

[PATCH v3 03/19] clk: sunxi: Add PLL3 clock

[Maxime Ripard]

The A10 SoCs and relatives have a PLL controller to drive the PLL3 and
PLL7, clocked from a 3MHz oscillator, that drives the display related
clocks (GPU, display engine, TCON, etc.)

Add a driver for it.

Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 Documentation/devicetree/bindings/clock/sunxi.txt |  1 +
 drivers/clk/sunxi/Makefile                        |  1 +
 drivers/clk/sunxi/clk-sun4i-pll3.c                | 98 +++++++++++++++++++++++
 3 files changed, 100 insertions(+)
 create mode 100644 drivers/clk/sunxi/clk-sun4i-pll3.c

diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index 50e212bc8923..0e1e2c0eee61 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -10,6 +10,7 @@ Required properties:
 	"allwinner,sun4i-a10-pll1-clk" - for the main PLL clock and PLL4
 	"allwinner,sun6i-a31-pll1-clk" - for the main PLL clock on A31
 	"allwinner,sun8i-a23-pll1-clk" - for the main PLL clock on A23
+	"allwinner,sun4i-a10-pll3-clk" - for the video PLL clock on A10
 	"allwinner,sun9i-a80-pll4-clk" - for the peripheral PLLs on A80
 	"allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
 	"allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
diff --git a/drivers/clk/sunxi/Makefile b/drivers/clk/sunxi/Makefile
index 37a6a642a037..244defcfa5db 100644
--- a/drivers/clk/sunxi/Makefile
+++ b/drivers/clk/sunxi/Makefile
@@ -12,6 +12,7 @@ obj-y += clk-a20-gmac.o
 obj-y += clk-mod0.o
 obj-y += clk-simple-gates.o
 obj-y += clk-sun4i-display.o
+obj-y += clk-sun4i-pll3.o
 obj-y += clk-sun8i-bus-gates.o
 obj-y += clk-sun8i-mbus.o
 obj-y += clk-sun9i-core.o
diff --git a/drivers/clk/sunxi/clk-sun4i-pll3.c b/drivers/clk/sunxi/clk-sun4i-pll3.c
new file mode 100644
index 000000000000..f66267e77d9c
--- /dev/null
+++ b/drivers/clk/sunxi/clk-sun4i-pll3.c
@@ -0,0 +1,98 @@
+/*
+ * Copyright 2015 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+
+#define SUN4I_A10_PLL3_GATE_BIT	31
+#define SUN4I_A10_PLL3_DIV_WIDTH	7
+#define SUN4I_A10_PLL3_DIV_SHIFT	0
+
+static DEFINE_SPINLOCK(sun4i_a10_pll3_lock);
+
+static void __init sun4i_a10_pll3_setup(struct device_node *node)
+{
+	const char *clk_name = node->name, *parent;
+	struct clk_multiplier *mult;
+	struct clk_gate *gate;
+	struct resource res;
+	void __iomem *reg;
+	struct clk *clk;
+	int ret;
+
+	of_property_read_string(node, "clock-output-names", &clk_name);
+	parent = of_clk_get_parent_name(node, 0);
+
+	reg = of_io_request_and_map(node, 0, of_node_full_name(node));
+	if (IS_ERR(reg)) {
+		pr_err("%s: Could not map the clock registers\n", clk_name);
+		return;
+	}
+
+	gate = kzalloc(sizeof(*gate), GFP_KERNEL);
+	if (!gate)
+		goto err_unmap;
+
+	gate->reg = reg;
+	gate->bit_idx = SUN4I_A10_PLL3_GATE_BIT;
+	gate->lock = &sun4i_a10_pll3_lock;
+
+	mult = kzalloc(sizeof(*mult), GFP_KERNEL);
+	if (!mult)
+		goto err_free_gate;
+
+	mult->reg = reg;
+	mult->shift = SUN4I_A10_PLL3_DIV_SHIFT;
+	mult->width = SUN4I_A10_PLL3_DIV_WIDTH;
+	mult->lock = &sun4i_a10_pll3_lock;
+
+	clk = clk_register_composite(NULL, clk_name,
+				     &parent, 1,
+				     NULL, NULL,
+				     &mult->hw, &clk_multiplier_ops,
+				     &gate->hw, &clk_gate_ops,
+				     0);
+	if (IS_ERR(clk)) {
+		pr_err("%s: Couldn't register the clock\n", clk_name);
+		goto err_free_mult;
+	}
+
+	ret = of_clk_add_provider(node, of_clk_src_simple_get, clk);
+	if (ret) {
+		pr_err("%s: Couldn't register DT provider\n",
+		       clk_name);
+		goto err_clk_unregister;
+	}
+
+	return;
+
+err_clk_unregister:
+	clk_unregister_composite(clk);
+err_free_mult:
+	kfree(mult);
+err_free_gate:
+	kfree(gate);
+err_unmap:
+	iounmap(reg);
+	of_address_to_resource(node, 0, &res);
+	release_mem_region(res.start, resource_size(&res));
+}
+
+CLK_OF_DECLARE(sun4i_a10_pll3, "allwinner,sun4i-a10-pll3-clk",
+	       sun4i_a10_pll3_setup);
-- 
2.7.3

[PATCH v3 04/19] clk: sunxi: Add TCON channel1 clock

[Maxime Ripard]

The TCON is a controller generating the timings to output videos signals,
acting like both a CRTC and an encoder.

It has two channels depending on the output, each channel being driven by
its own clock (and own clock controller).

Add a driver for the channel 1 clock.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/clock/sunxi.txt |   1 +
 drivers/clk/sunxi/Makefile                        |   1 +
 drivers/clk/sunxi/clk-sun4i-tcon-ch1.c            | 300 ++++++++++++++++++++++
 3 files changed, 302 insertions(+)
 create mode 100644 drivers/clk/sunxi/clk-sun4i-tcon-ch1.c

diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index 0e1e2c0eee61..54192c1a98dc 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -76,6 +76,7 @@ Required properties:
 	"allwinner,sun7i-a20-out-clk" - for the external output clocks
 	"allwinner,sun7i-a20-gmac-clk" - for the GMAC clock module on A20/A31
 	"allwinner,sun4i-a10-tcon-ch0-clk" - for the TCON channel 0 clock on the A10
+	"allwinner,sun4i-a10-tcon-ch1-clk" - for the TCON channel 1 clock on the A10
 	"allwinner,sun4i-a10-usb-clk" - for usb gates + resets on A10 / A20
 	"allwinner,sun5i-a13-usb-clk" - for usb gates + resets on A13
 	"allwinner,sun6i-a31-usb-clk" - for usb gates + resets on A31
diff --git a/drivers/clk/sunxi/Makefile b/drivers/clk/sunxi/Makefile
index 244defcfa5db..39d2044a1f49 100644
--- a/drivers/clk/sunxi/Makefile
+++ b/drivers/clk/sunxi/Makefile
@@ -13,6 +13,7 @@ obj-y += clk-mod0.o
 obj-y += clk-simple-gates.o
 obj-y += clk-sun4i-display.o
 obj-y += clk-sun4i-pll3.o
+obj-y += clk-sun4i-tcon-ch1.o
 obj-y += clk-sun8i-bus-gates.o
 obj-y += clk-sun8i-mbus.o
 obj-y += clk-sun9i-core.o
diff --git a/drivers/clk/sunxi/clk-sun4i-tcon-ch1.c b/drivers/clk/sunxi/clk-sun4i-tcon-ch1.c
new file mode 100644
index 000000000000..98a4582de56a
--- /dev/null
+++ b/drivers/clk/sunxi/clk-sun4i-tcon-ch1.c
@@ -0,0 +1,300 @@
+/*
+ * Copyright 2015 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+
+#define TCON_CH1_SCLK2_PARENTS		4
+
+#define TCON_CH1_SCLK2_GATE_BIT		BIT(31)
+#define TCON_CH1_SCLK2_MUX_MASK		3
+#define TCON_CH1_SCLK2_MUX_SHIFT	24
+#define TCON_CH1_SCLK2_DIV_MASK		0xf
+#define TCON_CH1_SCLK2_DIV_SHIFT	0
+
+#define TCON_CH1_SCLK1_GATE_BIT		BIT(15)
+#define TCON_CH1_SCLK1_HALF_BIT		BIT(11)
+
+struct tcon_ch1_clk {
+	struct clk_hw	hw;
+	spinlock_t	lock;
+	void __iomem	*reg;
+};
+
+#define hw_to_tclk(hw)	container_of(hw, struct tcon_ch1_clk, hw)
+
+static void tcon_ch1_disable(struct clk_hw *hw)
+{
+	struct tcon_ch1_clk *tclk = hw_to_tclk(hw);
+	unsigned long flags;
+	u32 reg;
+
+	spin_lock_irqsave(&tclk->lock, flags);
+	reg = readl(tclk->reg);
+	reg &= ~(TCON_CH1_SCLK2_GATE_BIT | TCON_CH1_SCLK1_GATE_BIT);
+	writel(reg, tclk->reg);
+	spin_unlock_irqrestore(&tclk->lock, flags);
+}
+
+static int tcon_ch1_enable(struct clk_hw *hw)
+{
+	struct tcon_ch1_clk *tclk = hw_to_tclk(hw);
+	unsigned long flags;
+	u32 reg;
+
+	spin_lock_irqsave(&tclk->lock, flags);
+	reg = readl(tclk->reg);
+	reg |= TCON_CH1_SCLK2_GATE_BIT | TCON_CH1_SCLK1_GATE_BIT;
+	writel(reg, tclk->reg);
+	spin_unlock_irqrestore(&tclk->lock, flags);
+
+	return 0;
+}
+
+static int tcon_ch1_is_enabled(struct clk_hw *hw)
+{
+	struct tcon_ch1_clk *tclk = hw_to_tclk(hw);
+	u32 reg;
+
+	reg = readl(tclk->reg);
+	return reg & (TCON_CH1_SCLK2_GATE_BIT | TCON_CH1_SCLK1_GATE_BIT);
+}
+
+static u8 tcon_ch1_get_parent(struct clk_hw *hw)
+{
+	struct tcon_ch1_clk *tclk = hw_to_tclk(hw);
+	int num_parents = clk_hw_get_num_parents(hw);
+	u32 reg;
+
+	reg = readl(tclk->reg) >> TCON_CH1_SCLK2_MUX_SHIFT;
+	reg &= reg >> TCON_CH1_SCLK2_MUX_MASK;
+
+	if (reg >= num_parents)
+		return -EINVAL;
+
+	return reg;
+}
+
+static int tcon_ch1_set_parent(struct clk_hw *hw, u8 index)
+{
+	struct tcon_ch1_clk *tclk = hw_to_tclk(hw);
+	unsigned long flags;
+	u32 reg;
+
+	spin_lock_irqsave(&tclk->lock, flags);
+	reg = readl(tclk->reg);
+	reg &= ~(TCON_CH1_SCLK2_MUX_MASK << TCON_CH1_SCLK2_MUX_SHIFT);
+	reg |= index << TCON_CH1_SCLK2_MUX_SHIFT;
+	writel(reg, tclk->reg);
+	spin_unlock_irqrestore(&tclk->lock, flags);
+
+	return 0;
+};
+
+static unsigned long tcon_ch1_calc_divider(unsigned long rate,
+					   unsigned long parent_rate,
+					   u8 *div,
+					   bool *half)
+{
+	unsigned long best_rate = 0;
+	u8 best_m = 0, m;
+	bool is_double;
+
+	for (m = 1; m < 16; m++) {
+		u8 d;
+
+		for (d = 1; d < 3; d++) {
+			unsigned long tmp_rate;
+
+			tmp_rate = parent_rate / m / d;
+
+			if (tmp_rate > rate)
+				continue;
+
+			if (!best_rate ||
+			    (rate - tmp_rate) < (rate - best_rate)) {
+				best_rate = tmp_rate;
+				best_m = m;
+				is_double = d;
+			}
+		}
+	}
+
+	if (div && half) {
+		*div = best_m;
+		*half = is_double;
+	}
+
+	return best_rate;
+}
+
+static int tcon_ch1_determine_rate(struct clk_hw *hw,
+				   struct clk_rate_request *req)
+{
+	long best_rate = -EINVAL;
+	int i;
+
+	for (i = 0; i < clk_hw_get_num_parents(hw); i++) {
+		unsigned long parent_rate;
+		unsigned long tmp_rate;
+		struct clk_hw *parent;
+
+		parent = clk_hw_get_parent_by_index(hw, i);
+		if (!parent)
+			continue;
+
+		parent_rate = clk_hw_get_rate(parent);
+
+		tmp_rate = tcon_ch1_calc_divider(req->rate, parent_rate,
+						 NULL, NULL);
+
+		if (best_rate < 0 ||
+		    (req->rate - tmp_rate) < (req->rate - best_rate)) {
+			best_rate = tmp_rate;
+			req->best_parent_rate = parent_rate;
+			req->best_parent_hw = parent;
+		}
+	}
+
+	if (best_rate < 0)
+		return best_rate;
+
+	req->rate = best_rate;
+	return 0;
+}
+
+static unsigned long tcon_ch1_recalc_rate(struct clk_hw *hw,
+					  unsigned long parent_rate)
+{
+	struct tcon_ch1_clk *tclk = hw_to_tclk(hw);
+	u32 reg;
+
+	reg = readl(tclk->reg);
+
+	parent_rate /= (reg & TCON_CH1_SCLK2_DIV_MASK) + 1;
+
+	if (reg & TCON_CH1_SCLK1_HALF_BIT)
+		parent_rate /= 2;
+
+	return parent_rate;
+}
+
+static int tcon_ch1_set_rate(struct clk_hw *hw, unsigned long rate,
+			     unsigned long parent_rate)
+{
+	struct tcon_ch1_clk *tclk = hw_to_tclk(hw);
+	unsigned long flags;
+	bool half;
+	u8 div_m;
+	u32 reg;
+
+	tcon_ch1_calc_divider(rate, parent_rate, &div_m, &half);
+
+	spin_lock_irqsave(&tclk->lock, flags);
+	reg = readl(tclk->reg);
+	reg &= ~(TCON_CH1_SCLK2_DIV_MASK | TCON_CH1_SCLK1_HALF_BIT);
+	reg |= (div_m - 1) & TCON_CH1_SCLK2_DIV_MASK;
+
+	if (half)
+		reg |= TCON_CH1_SCLK1_HALF_BIT;
+
+	writel(reg, tclk->reg);
+	spin_unlock_irqrestore(&tclk->lock, flags);
+
+	return 0;
+}
+
+static const struct clk_ops tcon_ch1_ops = {
+	.disable	= tcon_ch1_disable,
+	.enable		= tcon_ch1_enable,
+	.is_enabled	= tcon_ch1_is_enabled,
+
+	.get_parent	= tcon_ch1_get_parent,
+	.set_parent	= tcon_ch1_set_parent,
+
+	.determine_rate	= tcon_ch1_determine_rate,
+	.recalc_rate	= tcon_ch1_recalc_rate,
+	.set_rate	= tcon_ch1_set_rate,
+};
+
+static void __init tcon_ch1_setup(struct device_node *node)
+{
+	const char *parents[TCON_CH1_SCLK2_PARENTS];
+	const char *clk_name = node->name;
+	struct clk_init_data init;
+	struct tcon_ch1_clk *tclk;
+	struct resource res;
+	struct clk *clk;
+	void __iomem *reg;
+	int ret;
+
+	of_property_read_string(node, "clock-output-names", &clk_name);
+
+	reg = of_io_request_and_map(node, 0, of_node_full_name(node));
+	if (IS_ERR(reg)) {
+		pr_err("%s: Could not map the clock registers\n", clk_name);
+		return;
+	}
+
+	ret = of_clk_parent_fill(node, parents, TCON_CH1_SCLK2_PARENTS);
+	if (ret != TCON_CH1_SCLK2_PARENTS) {
+		pr_err("%s Could not retrieve the parents\n", clk_name);
+		goto err_unmap;
+	}
+
+	tclk = kzalloc(sizeof(*tclk), GFP_KERNEL);
+	if (!tclk)
+		goto err_unmap;
+
+	init.name = clk_name;
+	init.ops = &tcon_ch1_ops;
+	init.parent_names = parents;
+	init.num_parents = TCON_CH1_SCLK2_PARENTS;
+	init.flags = CLK_SET_RATE_PARENT;
+
+	tclk->reg = reg;
+	tclk->hw.init = &init;
+	spin_lock_init(&tclk->lock);
+
+	clk = clk_register(NULL, &tclk->hw);
+	if (IS_ERR(clk)) {
+		pr_err("%s: Couldn't register the clock\n", clk_name);
+		goto err_free_data;
+	}
+
+	ret = of_clk_add_provider(node, of_clk_src_simple_get, clk);
+	if (ret) {
+		pr_err("%s: Couldn't register our clock provider\n", clk_name);
+		goto err_unregister_clk;
+	}
+
+	return;
+
+err_unregister_clk:
+	clk_unregister(clk);
+err_free_data:
+	kfree(tclk);
+err_unmap:
+	iounmap(reg);
+	of_address_to_resource(node, 0, &res);
+	release_mem_region(res.start, resource_size(&res));
+}
+
+CLK_OF_DECLARE(tcon_ch1, "allwinner,sun4i-a10-tcon-ch1-clk",
+	       tcon_ch1_setup);
-- 
2.7.3

[PATCH v3 05/19] dt-bindings: clk: sun5i: add DRAM gates compatible

[Maxime Ripard]

The Allwinner SoCs have a gate controller to gate the access to the DRAM
clock to the some devices that need to access the DRAM directly (mostly
display / image related IPs).

Use a simple gates driver to support the one found in the A13 / R8 SoCs.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/clock/sunxi.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index 54192c1a98dc..e194cda2f469 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -66,6 +66,7 @@ Required properties:
 	"allwinner,sun9i-a80-apbs-gates-clk" - for the APBS gates on A80
 	"allwinner,sun4i-a10-dram-gates-clk" - for the DRAM gates on A10
 	"allwinner,sun4i-a10-display-clk" - for the display clocks on the A10
+	"allwinner,sun5i-a13-dram-gates-clk" - for the DRAM gates on A13
 	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
 	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
 	"allwinner,sun9i-a80-mmc-clk" - for mmc module clocks on A80
-- 
2.7.3

[PATCH v3 06/19] ARM: sun5i: dt: Add pll3 and pll7 clocks

[Maxime Ripard]

Enable the pll3 and pll7 clocks in the DT that are used to drive the
display-related clocks.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm/boot/dts/sun5i.dtsi | 43 +++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 43 insertions(+)

diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi
index 59a9426e3bd4..0840612b5ed6 100644
--- a/arch/arm/boot/dts/sun5i.dtsi
+++ b/arch/arm/boot/dts/sun5i.dtsi
@@ -88,6 +88,15 @@
 			clock-output-names = "osc24M";
 		};
 
+		osc3M: osc3M_clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clock-div = <8>;
+			clock-mult = <1>;
+			clocks = <&osc24M>;
+			clock-output-names = "osc3M";
+		};
+
 		osc32k: clk@0 {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
@@ -112,6 +121,23 @@
 					     "pll2-4x", "pll2-8x";
 		};
 
+		pll3: clk@01c20010 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-pll3-clk";
+			reg = <0x01c20010 0x4>;
+			clocks = <&osc3M>;
+			clock-output-names = "pll3";
+		};
+
+		pll3x2: pll3x2_clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clock-div = <1>;
+			clock-mult = <2>;
+			clocks = <&pll3>;
+			clock-output-names = "pll3-2x";
+		};
+
 		pll4: clk@01c20018 {
 			#clock-cells = <0>;
 			compatible = "allwinner,sun4i-a10-pll1-clk";
@@ -136,6 +162,23 @@
 			clock-output-names = "pll6_sata", "pll6_other", "pll6";
 		};
 
+		pll7: clk@01c20030 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-pll3-clk";
+			reg = <0x01c20030 0x4>;
+			clocks = <&osc3M>;
+			clock-output-names = "pll7";
+		};
+
+		pll7x2: pll7x2_clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clock-div = <1>;
+			clock-mult = <2>;
+			clocks = <&pll7>;
+			clock-output-names = "pll7-2x";
+		};
+
 		/* dummy is 200M */
 		cpu: cpu@01c20054 {
 			#clock-cells = <0>;
-- 
2.7.3

[PATCH v3 07/19] ARM: sun5i: a13: Add display and TCON clocks

[Maxime Ripard]

Enable the display and TCON (channel 0 and channel 1) clocks that are going
to be needed to drive the display engine, tcon and TV encoders.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/sun5i-a13.dtsi | 38 +++++++++++++++++++++++++++++++++++++-
 arch/arm/boot/dts/sun5i-r8.dtsi  |  5 +++--
 2 files changed, 40 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/sun5i-a13.dtsi
index d910d3a6c41c..9669b03f20f3 100644
--- a/arch/arm/boot/dts/sun5i-a13.dtsi
+++ b/arch/arm/boot/dts/sun5i-a13.dtsi
@@ -61,7 +61,8 @@
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0";
-			clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>;
+			clocks = <&ahb_gates 36>, <&ahb_gates 44>, <&de_be_clk>,
+				 <&tcon_ch0_clk>;
 			status = "disabled";
 		};
 	};
@@ -149,6 +150,41 @@
 					     "apb1_i2c2", "apb1_uart1",
 					     "apb1_uart3";
 		};
+
+		de_be_clk: clk@01c20104 {
+			#clock-cells = <0>;
+			#reset-cells = <0>;
+			compatible = "allwinner,sun4i-a10-display-clk";
+			reg = <0x01c20104 0x4>;
+			clocks = <&pll3>, <&pll7>, <&pll5 1>;
+			clock-output-names = "de-be";
+		};
+
+		de_fe_clk: clk@01c2010c {
+			#clock-cells = <0>;
+			#reset-cells = <0>;
+			compatible = "allwinner,sun4i-a10-display-clk";
+			reg = <0x01c2010c 0x4>;
+			clocks = <&pll3>, <&pll7>, <&pll5 1>;
+			clock-output-names = "de-fe";
+		};
+
+		tcon_ch0_clk: clk@01c20118 {
+			#clock-cells = <0>;
+			#reset-cells = <1>;
+			compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
+			reg = <0x01c20118 0x4>;
+			clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+			clock-output-names = "tcon-ch0-sclk";
+		};
+
+		tcon_ch1_clk: clk@01c2012c {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
+			reg = <0x01c2012c 0x4>;
+			clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+			clock-output-names = "tcon-ch1-sclk";
+		};
 	};
 
 	soc@01c00000 {
diff --git a/arch/arm/boot/dts/sun5i-r8.dtsi b/arch/arm/boot/dts/sun5i-r8.dtsi
index 0ef865601ac9..b1e4e0170d51 100644
--- a/arch/arm/boot/dts/sun5i-r8.dtsi
+++ b/arch/arm/boot/dts/sun5i-r8.dtsi
@@ -51,8 +51,9 @@
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0-tve0";
-			clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>,
-				 <&ahb_gates 44>;
+			clocks = <&ahb_gates 34>, <&ahb_gates 36>,
+				 <&ahb_gates 44>, <&de_be_clk>,
+				 <&tcon_ch1_clk>;
 			status = "disabled";
 		};
 	};
-- 
2.7.3

[PATCH v3 08/19] ARM: sun5i: Add DRAM gates

[Maxime Ripard]

The DRAM gates control whether the image / display devices on the SoC have
access to the DRAM clock or not.

Enable it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/sun5i-a13.dtsi | 22 +++++++++++++++++++++-
 arch/arm/boot/dts/sun5i-r8.dtsi  |  2 +-
 2 files changed, 22 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/sun5i-a13.dtsi
index 9669b03f20f3..d3d2b19c97f1 100644
--- a/arch/arm/boot/dts/sun5i-a13.dtsi
+++ b/arch/arm/boot/dts/sun5i-a13.dtsi
@@ -62,7 +62,7 @@
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0";
 			clocks = <&ahb_gates 36>, <&ahb_gates 44>, <&de_be_clk>,
-				 <&tcon_ch0_clk>;
+				 <&tcon_ch0_clk>, <&dram_gates 26>;
 			status = "disabled";
 		};
 	};
@@ -151,6 +151,26 @@
 					     "apb1_uart3";
 		};
 
+		dram_gates: clk@01c20100 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun5i-a13-dram-gates-clk",
+				     "allwinner,sun4i-a10-gates-clk";
+			reg = <0x01c20100 0x4>;
+			clocks = <&pll5 0>;
+			clock-indices = <0>,
+					<1>,
+					<25>,
+					<26>,
+					<29>,
+					<31>;
+			clock-output-names = "dram_ve",
+					     "dram_csi",
+					     "dram_de_fe",
+					     "dram_de_be",
+					     "dram_ace",
+					     "dram_iep";
+		};
+
 		de_be_clk: clk@01c20104 {
 			#clock-cells = <0>;
 			#reset-cells = <0>;
diff --git a/arch/arm/boot/dts/sun5i-r8.dtsi b/arch/arm/boot/dts/sun5i-r8.dtsi
index b1e4e0170d51..691d3de75b35 100644
--- a/arch/arm/boot/dts/sun5i-r8.dtsi
+++ b/arch/arm/boot/dts/sun5i-r8.dtsi
@@ -53,7 +53,7 @@
 			allwinner,pipeline = "de_be0-lcd0-tve0";
 			clocks = <&ahb_gates 34>, <&ahb_gates 36>,
 				 <&ahb_gates 44>, <&de_be_clk>,
-				 <&tcon_ch1_clk>;
+				 <&tcon_ch1_clk>, <&dram_gates 26>;
 			status = "disabled";
 		};
 	};
-- 
2.7.3

[PATCH v3 09/19] ARM: sun5i: Add TV encoder gate to the DTSI

[Maxime Ripard]

It turns out that the A13 / R8 also have a tve encoder block, and a gate
for it.

Add it to the DT.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm/boot/dts/sun5i-a13.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/sun5i-a13.dtsi
index d3d2b19c97f1..263d46dbc7e6 100644
--- a/arch/arm/boot/dts/sun5i-a13.dtsi
+++ b/arch/arm/boot/dts/sun5i-a13.dtsi
@@ -111,8 +111,8 @@
 					<10>, <13>,
 					<14>, <20>,
 					<21>, <22>,
-				        <28>, <32>, <36>,
-				        <40>, <44>,
+					<28>, <32>, <34>,
+					<36>, <40>, <44>,
 					<46>, <51>,
 					<52>;
 			clock-output-names = "ahb_usbotg", "ahb_ehci",
@@ -121,8 +121,8 @@
 					     "ahb_mmc2", "ahb_nand",
 					     "ahb_sdram", "ahb_spi0",
 					     "ahb_spi1", "ahb_spi2",
-					     "ahb_stimer", "ahb_ve", "ahb_lcd",
-					     "ahb_csi", "ahb_de_be",
+					     "ahb_stimer", "ahb_ve", "ahb_tve",
+					     "ahb_lcd", "ahb_csi", "ahb_de_be",
 					     "ahb_de_fe", "ahb_iep",
 					     "ahb_mali400";
 		};
-- 
2.7.3

[PATCH v3 10/19] drm: fb: Add seq_file definition

[Maxime Ripard]

Otherwise, building with DEBUG_FS enabled will trigger a build warning
because we're using a structure that has not been declared.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 include/drm/drm_fb_cma_helper.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/include/drm/drm_fb_cma_helper.h b/include/drm/drm_fb_cma_helper.h
index be62bd321e75..ae49c24fbf50 100644
--- a/include/drm/drm_fb_cma_helper.h
+++ b/include/drm/drm_fb_cma_helper.h
@@ -24,6 +24,8 @@ struct drm_gem_cma_object *drm_fb_cma_get_gem_obj(struct drm_framebuffer *fb,
 	unsigned int plane);
 
 #ifdef CONFIG_DEBUG_FS
+struct seq_file;
+
 int drm_fb_cma_debugfs_show(struct seq_file *m, void *arg);
 #endif
 
-- 
2.7.3

[PATCH v3 11/19] drm/panel: simple: Add timings for the Olimex LCD-OLinuXino-4.3TS

[Maxime Ripard]

Add support for the Olimex LCD-OLinuXino-4.3TS panel to the DRM simple
panel driver.

It is a 480x272 panel connected through a 24-bits RGB interface.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/olimex,lcd-olinuxino-43-ts.txt   |  7 ++++++
 drivers/gpu/drm/panel/panel-simple.c               | 26 ++++++++++++++++++++++
 2 files changed, 33 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt

diff --git a/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt b/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt
new file mode 100644
index 000000000000..74540a090669
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt
@@ -0,0 +1,7 @@
+Olimex 4.3" TFT LCD panel
+
+Required properties:
+- compatible: should be "olimex,lcd-olinuxino-43-ts"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index ceb20486dacf..f95abdbde147 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -1084,6 +1084,29 @@ static const struct panel_desc okaya_rs800480t_7x0gp = {
 	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
 };
 
+static const struct drm_display_mode olimex_lcd_olinuxino_43ts_mode = {
+	.clock = 9000,
+	.hdisplay = 480,
+	.hsync_start = 480 + 5,
+	.hsync_end = 480 + 5 + 30,
+	.htotal = 480 + 5 + 30 + 10,
+	.vdisplay = 272,
+	.vsync_start = 272 + 8,
+	.vsync_end = 272 + 8 + 5,
+	.vtotal = 272 + 8 + 5 + 3,
+	.vrefresh = 60,
+};
+
+static const struct panel_desc olimex_lcd_olinuxino_43ts = {
+	.modes = &olimex_lcd_olinuxino_43ts_mode,
+	.num_modes = 1,
+	.size = {
+		.width = 105,
+		.height = 67,
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
+};
+
 static const struct drm_display_mode ortustech_com43h4m85ulc_mode  = {
 	.clock = 25000,
 	.hdisplay = 480,
@@ -1329,6 +1352,9 @@ static const struct of_device_id platform_of_match[] = {
 		.compatible = "okaya,rs800480t-7x0gp",
 		.data = &okaya_rs800480t_7x0gp,
 	}, {
+		.compatible = "olimex,lcd-olinuxino-43-ts",
+		.data = &olimex_lcd_olinuxino_43ts,
+	}, {
 		.compatible = "ortustech,com43h4m85ulc",
 		.data = &ortustech_com43h4m85ulc,
 	}, {
-- 
2.7.3

[PATCH v3 12/19] drm: Add Allwinner A10 Display Engine support

[Maxime Ripard]

The Allwinner A10 and subsequent SoCs share the same display pipeline, with
variations in the number of controllers (1 or 2), or the presence or not of
some output (HDMI, TV, VGA) or not.

Add a driver with a limited set of features for now, and we will hopefully
support all of them eventually

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 drivers/gpu/drm/Kconfig                   |   2 +
 drivers/gpu/drm/Makefile                  |   3 +-
 drivers/gpu/drm/sun4i/Kconfig             |  14 +
 drivers/gpu/drm/sun4i/Makefile            |  10 +
 drivers/gpu/drm/sun4i/sun4i_backend.c     | 364 ++++++++++++++++++++++
 drivers/gpu/drm/sun4i/sun4i_backend.h     | 165 ++++++++++
 drivers/gpu/drm/sun4i/sun4i_crtc.c        | 120 ++++++++
 drivers/gpu/drm/sun4i/sun4i_crtc.h        |  30 ++
 drivers/gpu/drm/sun4i/sun4i_dotclock.c    | 160 ++++++++++
 drivers/gpu/drm/sun4i/sun4i_dotclock.h    |  21 ++
 drivers/gpu/drm/sun4i/sun4i_drv.c         | 319 +++++++++++++++++++
 drivers/gpu/drm/sun4i/sun4i_drv.h         |  30 ++
 drivers/gpu/drm/sun4i/sun4i_framebuffer.c |  54 ++++
 drivers/gpu/drm/sun4i/sun4i_framebuffer.h |  19 ++
 drivers/gpu/drm/sun4i/sun4i_layer.c       | 161 ++++++++++
 drivers/gpu/drm/sun4i/sun4i_layer.h       |  30 ++
 drivers/gpu/drm/sun4i/sun4i_tcon.c        | 492 ++++++++++++++++++++++++++++++
 drivers/gpu/drm/sun4i/sun4i_tcon.h        | 184 +++++++++++
 18 files changed, 2177 insertions(+), 1 deletion(-)
 create mode 100644 drivers/gpu/drm/sun4i/Kconfig
 create mode 100644 drivers/gpu/drm/sun4i/Makefile
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_backend.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_backend.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_crtc.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_crtc.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_dotclock.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_dotclock.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_drv.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_drv.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_framebuffer.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_framebuffer.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_layer.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_layer.h
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_tcon.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_tcon.h

diff --git a/drivers/gpu/drm/Kconfig b/drivers/gpu/drm/Kconfig
index f2a74d0b68ae..420779064e49 100644
--- a/drivers/gpu/drm/Kconfig
+++ b/drivers/gpu/drm/Kconfig
@@ -252,6 +252,8 @@ source "drivers/gpu/drm/rcar-du/Kconfig"
 
 source "drivers/gpu/drm/shmobile/Kconfig"
 
+source "drivers/gpu/drm/sun4i/Kconfig"
+
 source "drivers/gpu/drm/omapdrm/Kconfig"
 
 source "drivers/gpu/drm/tilcdc/Kconfig"
diff --git a/drivers/gpu/drm/Makefile b/drivers/gpu/drm/Makefile
index 6eb94fc561dc..e163fd3cd604 100644
--- a/drivers/gpu/drm/Makefile
+++ b/drivers/gpu/drm/Makefile
@@ -1,4 +1,4 @@
-#
+
 # Makefile for the drm device driver.  This driver provides support for the
 # Direct Rendering Infrastructure (DRI) in XFree86 4.1.0 and higher.
 
@@ -65,6 +65,7 @@ obj-$(CONFIG_DRM_ATMEL_HLCDC)	+= atmel-hlcdc/
 obj-$(CONFIG_DRM_RCAR_DU) += rcar-du/
 obj-$(CONFIG_DRM_SHMOBILE) +=shmobile/
 obj-y			+= omapdrm/
+obj-$(CONFIG_DRM_SUN4I) += sun4i/
 obj-y			+= tilcdc/
 obj-$(CONFIG_DRM_QXL) += qxl/
 obj-$(CONFIG_DRM_BOCHS) += bochs/
diff --git a/drivers/gpu/drm/sun4i/Kconfig b/drivers/gpu/drm/sun4i/Kconfig
new file mode 100644
index 000000000000..99510e64e91a
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/Kconfig
@@ -0,0 +1,14 @@
+config DRM_SUN4I
+	tristate "DRM Support for Allwinner A10 Display Engine"
+	depends on DRM && ARM
+	depends on ARCH_SUNXI || COMPILE_TEST
+	select DRM_GEM_CMA_HELPER
+	select DRM_KMS_HELPER
+	select DRM_KMS_CMA_HELPER
+	select DRM_PANEL
+	select REGMAP_MMIO
+	select VIDEOMODE_HELPERS
+	help
+	  Choose this option if you have an Allwinner SoC with a
+	  Display Engine. If M is selected the module will be called
+	  sun4i-drm.
diff --git a/drivers/gpu/drm/sun4i/Makefile b/drivers/gpu/drm/sun4i/Makefile
new file mode 100644
index 000000000000..6df3ef32732d
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/Makefile
@@ -0,0 +1,10 @@
+sun4i-drm-y += sun4i_crtc.o
+sun4i-drm-y += sun4i_drv.o
+sun4i-drm-y += sun4i_framebuffer.o
+sun4i-drm-y += sun4i_layer.o
+
+sun4i-tcon-y += sun4i_tcon.o
+sun4i-tcon-y += sun4i_dotclock.o
+
+obj-$(CONFIG_DRM_SUN4I)		+= sun4i-drm.o sun4i-tcon.o
+obj-$(CONFIG_DRM_SUN4I)		+= sun4i_backend.o
diff --git a/drivers/gpu/drm/sun4i/sun4i_backend.c b/drivers/gpu/drm/sun4i/sun4i_backend.c
new file mode 100644
index 000000000000..f7a15c1a93bf
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_backend.c
@@ -0,0 +1,364 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <drm/drmP.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_fb_cma_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_plane_helper.h>
+
+#include <linux/component.h>
+#include <linux/reset.h>
+
+#include "sun4i_backend.h"
+#include "sun4i_drv.h"
+
+static u32 sunxi_rgb2yuv_coef[12] = {
+	0x00000107, 0x00000204, 0x00000064, 0x00000108,
+	0x00003f69, 0x00003ed6, 0x000001c1, 0x00000808,
+	0x000001c1, 0x00003e88, 0x00003fb8, 0x00000808
+};
+
+void sun4i_backend_apply_color_correction(struct sun4i_backend *backend)
+{
+	int i;
+
+	DRM_DEBUG_DRIVER("Applying RGB to YUV color correction\n");
+
+	/* Set color correction */
+	regmap_write(backend->regs, SUN4I_BACKEND_OCCTL_REG,
+		     SUN4I_BACKEND_OCCTL_ENABLE);
+
+	for (i = 0; i < 12; i++)
+		regmap_write(backend->regs, SUN4I_BACKEND_OCRCOEF_REG(i),
+			     sunxi_rgb2yuv_coef[i]);
+}
+EXPORT_SYMBOL(sun4i_backend_apply_color_correction);
+
+void sun4i_backend_disable_color_correction(struct sun4i_backend *backend)
+{
+	DRM_DEBUG_DRIVER("Disabling color correction\n");
+
+	/* Disable color correction */
+	regmap_update_bits(backend->regs, SUN4I_BACKEND_OCCTL_REG,
+			   SUN4I_BACKEND_OCCTL_ENABLE, 0);
+}
+EXPORT_SYMBOL(sun4i_backend_disable_color_correction);
+
+void sun4i_backend_commit(struct sun4i_backend *backend)
+{
+	DRM_DEBUG_DRIVER("Committing changes\n");
+
+	regmap_write(backend->regs, SUN4I_BACKEND_REGBUFFCTL_REG,
+		     SUN4I_BACKEND_REGBUFFCTL_AUTOLOAD_DIS |
+		     SUN4I_BACKEND_REGBUFFCTL_LOADCTL);
+}
+EXPORT_SYMBOL(sun4i_backend_commit);
+
+void sun4i_backend_layer_enable(struct sun4i_backend *backend,
+				int layer, bool enable)
+{
+	u32 val;
+
+	DRM_DEBUG_DRIVER("Enabling layer %d\n", layer);
+
+	if (enable)
+		val = SUN4I_BACKEND_MODCTL_LAY_EN(layer);
+	else
+		val = 0;
+
+	regmap_update_bits(backend->regs, SUN4I_BACKEND_MODCTL_REG,
+			   SUN4I_BACKEND_MODCTL_LAY_EN(layer), val);
+}
+EXPORT_SYMBOL(sun4i_backend_layer_enable);
+
+static int sun4i_backend_drm_format_to_layer(u32 format, u32 *mode)
+{
+	switch (format) {
+	case DRM_FORMAT_ARGB8888:
+		*mode = SUN4I_BACKEND_LAY_FBFMT_ARGB8888;
+		break;
+
+	case DRM_FORMAT_XRGB8888:
+		*mode = SUN4I_BACKEND_LAY_FBFMT_XRGB8888;
+		break;
+
+	case DRM_FORMAT_RGB888:
+		*mode = SUN4I_BACKEND_LAY_FBFMT_RGB888;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+int sun4i_backend_update_layer_coord(struct sun4i_backend *backend,
+				     int layer, struct drm_plane *plane)
+{
+	struct drm_plane_state *state = plane->state;
+	struct drm_framebuffer *fb = state->fb;
+
+	DRM_DEBUG_DRIVER("Updating layer %d\n", layer);
+
+	if (plane->type == DRM_PLANE_TYPE_PRIMARY) {
+		DRM_DEBUG_DRIVER("Primary layer, updating global size W: %u H: %u\n",
+				 state->crtc_w, state->crtc_h);
+		regmap_write(backend->regs, SUN4I_BACKEND_DISSIZE_REG,
+			     SUN4I_BACKEND_DISSIZE(state->crtc_w,
+						   state->crtc_h));
+	}
+
+	/* Set the line width */
+	DRM_DEBUG_DRIVER("Layer line width: %d bits\n", fb->pitches[0] * 8);
+	regmap_write(backend->regs, SUN4I_BACKEND_LAYLINEWIDTH_REG(layer),
+		     fb->pitches[0] * 8);
+
+	/* Set height and width */
+	DRM_DEBUG_DRIVER("Layer size W: %u H: %u\n",
+			 state->crtc_w, state->crtc_h);
+	regmap_write(backend->regs, SUN4I_BACKEND_LAYSIZE_REG(layer),
+		     SUN4I_BACKEND_LAYSIZE(state->crtc_w,
+					   state->crtc_h));
+
+	/* Set base coordinates */
+	DRM_DEBUG_DRIVER("Layer coordinates X: %d Y: %d\n",
+			 state->crtc_x, state->crtc_y);
+	regmap_write(backend->regs, SUN4I_BACKEND_LAYCOOR_REG(layer),
+		     SUN4I_BACKEND_LAYCOOR(state->crtc_x,
+					   state->crtc_y));
+
+	return 0;
+}
+EXPORT_SYMBOL(sun4i_backend_update_layer_coord);
+
+int sun4i_backend_update_layer_formats(struct sun4i_backend *backend,
+				       int layer, struct drm_plane *plane)
+{
+	struct drm_plane_state *state = plane->state;
+	struct drm_framebuffer *fb = state->fb;
+	bool interlaced = false;
+	u32 val;
+	int ret;
+
+	if (plane->state->crtc)
+		interlaced = plane->state->crtc->state->adjusted_mode.flags
+			& DRM_MODE_FLAG_INTERLACE;
+
+	regmap_update_bits(backend->regs, SUN4I_BACKEND_MODCTL_REG,
+			   SUN4I_BACKEND_MODCTL_ITLMOD_EN,
+			   interlaced ? SUN4I_BACKEND_MODCTL_ITLMOD_EN : 0);
+
+	DRM_DEBUG_DRIVER("Switching display backend interlaced mode %s\n",
+			 interlaced ? "on" : "off");
+
+	ret = sun4i_backend_drm_format_to_layer(fb->pixel_format, &val);
+	if (ret) {
+		DRM_DEBUG_DRIVER("Invalid format\n");
+		return val;
+	}
+
+	regmap_update_bits(backend->regs, SUN4I_BACKEND_ATTCTL_REG1(layer),
+			   SUN4I_BACKEND_ATTCTL_REG1_LAY_FBFMT, val);
+
+	return 0;
+}
+EXPORT_SYMBOL(sun4i_backend_update_layer_formats);
+
+int sun4i_backend_update_layer_buffer(struct sun4i_backend *backend,
+				      int layer, struct drm_plane *plane)
+{
+	struct drm_plane_state *state = plane->state;
+	struct drm_framebuffer *fb = state->fb;
+	struct drm_gem_cma_object *gem;
+	u32 lo_paddr, hi_paddr;
+	dma_addr_t paddr;
+	int bpp;
+
+	/* Get the physical address of the buffer in memory */
+	gem = drm_fb_cma_get_gem_obj(fb, 0);
+
+	DRM_DEBUG_DRIVER("Using GEM @ 0x%x\n", gem->paddr);
+
+	/* Compute the start of the displayed memory */
+	bpp = drm_format_plane_cpp(fb->pixel_format, 0);
+	paddr = gem->paddr + fb->offsets[0];
+	paddr += (state->src_x >> 16) * bpp;
+	paddr += (state->src_y >> 16) * fb->pitches[0];
+
+	DRM_DEBUG_DRIVER("Setting buffer address to 0x%x\n", paddr);
+
+	/* Write the 32 lower bits of the address (in bits) */
+	lo_paddr = paddr << 3;
+	DRM_DEBUG_DRIVER("Setting address lower bits to 0x%x\n", lo_paddr);
+	regmap_write(backend->regs, SUN4I_BACKEND_LAYFB_L32ADD_REG(layer),
+		     lo_paddr);
+
+	/* And the upper bits */
+	hi_paddr = paddr >> 29;
+	DRM_DEBUG_DRIVER("Setting address high bits to 0x%x\n", hi_paddr);
+	regmap_update_bits(backend->regs, SUN4I_BACKEND_LAYFB_H4ADD_REG,
+			   SUN4I_BACKEND_LAYFB_H4ADD_MSK(layer),
+			   SUN4I_BACKEND_LAYFB_H4ADD(layer, hi_paddr));
+
+	return 0;
+}
+EXPORT_SYMBOL(sun4i_backend_update_layer_buffer);
+
+static struct regmap_config sun4i_backend_regmap_config = {
+	.reg_bits	= 32,
+	.val_bits	= 32,
+	.reg_stride	= 4,
+	.max_register	= 0x5800,
+};
+
+static int sun4i_backend_bind(struct device *dev, struct device *master,
+			      void *data)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct drm_device *drm = data;
+	struct sun4i_drv *drv = drm->dev_private;
+	struct sun4i_backend *backend;
+	struct resource *res;
+	void __iomem *regs;
+	int i, ret;
+
+	backend = devm_kzalloc(dev, sizeof(*backend), GFP_KERNEL);
+	if (!backend)
+		return -ENOMEM;
+	dev_set_drvdata(dev, backend);
+	drv->backend = backend;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(regs)) {
+		dev_err(dev, "Couldn't map the backend registers\n");
+		return PTR_ERR(regs);
+	}
+
+	backend->regs = devm_regmap_init_mmio(dev, regs,
+					      &sun4i_backend_regmap_config);
+	if (IS_ERR(backend->regs)) {
+		dev_err(dev, "Couldn't create the backend0 regmap\n");
+		return PTR_ERR(backend->regs);
+	}
+
+	backend->reset = devm_reset_control_get(dev, NULL);
+	if (IS_ERR(backend->reset)) {
+		dev_err(dev, "Couldn't get our reset line\n");
+		return PTR_ERR(backend->reset);
+	}
+
+	ret = reset_control_deassert(backend->reset);
+	if (ret) {
+		dev_err(dev, "Couldn't deassert our reset line\n");
+		return ret;
+	}
+
+	backend->bus_clk = devm_clk_get(dev, "ahb");
+	if (IS_ERR(backend->bus_clk)) {
+		dev_err(dev, "Couldn't get the backend bus clock\n");
+		ret = PTR_ERR(backend->bus_clk);
+		goto err_assert_reset;
+	}
+	clk_prepare_enable(backend->bus_clk);
+
+	backend->mod_clk = devm_clk_get(dev, "mod");
+	if (IS_ERR(backend->mod_clk)) {
+		dev_err(dev, "Couldn't get the backend module clock\n");
+		ret = PTR_ERR(backend->mod_clk);
+		goto err_disable_bus_clk;
+	}
+	clk_prepare_enable(backend->mod_clk);
+
+	backend->ram_clk = devm_clk_get(dev, "ram");
+	if (IS_ERR(backend->ram_clk)) {
+		dev_err(dev, "Couldn't get the backend RAM clock\n");
+		ret = PTR_ERR(backend->ram_clk);
+		goto err_disable_mod_clk;
+	}
+	clk_prepare_enable(backend->ram_clk);
+
+	/* Reset the registers */
+	for (i = 0x800; i < 0x1000; i += 4)
+		regmap_write(backend->regs, i, 0);
+
+	/* Disable registers autoloading */
+	regmap_write(backend->regs, SUN4I_BACKEND_REGBUFFCTL_REG,
+		     SUN4I_BACKEND_REGBUFFCTL_AUTOLOAD_DIS);
+
+	/* Enable the backend */
+	regmap_write(backend->regs, SUN4I_BACKEND_MODCTL_REG,
+		     SUN4I_BACKEND_MODCTL_DEBE_EN |
+		     SUN4I_BACKEND_MODCTL_START_CTL);
+
+	return 0;
+
+err_disable_mod_clk:
+	clk_disable_unprepare(backend->mod_clk);
+err_disable_bus_clk:
+	clk_disable_unprepare(backend->bus_clk);
+err_assert_reset:
+	reset_control_assert(backend->reset);
+	return ret;
+}
+
+static void sun4i_backend_unbind(struct device *dev, struct device *master,
+				 void *data)
+{
+	struct sun4i_backend *backend = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(backend->ram_clk);
+	clk_disable_unprepare(backend->mod_clk);
+	clk_disable_unprepare(backend->bus_clk);
+	reset_control_assert(backend->reset);
+}
+
+static struct component_ops sun4i_backend_ops = {
+	.bind	= sun4i_backend_bind,
+	.unbind	= sun4i_backend_unbind,
+};
+
+static int sun4i_backend_probe(struct platform_device *pdev)
+{
+	return component_add(&pdev->dev, &sun4i_backend_ops);
+}
+
+static int sun4i_backend_remove(struct platform_device *pdev)
+{
+	component_del(&pdev->dev, &sun4i_backend_ops);
+
+	return 0;
+}
+
+static const struct of_device_id sun4i_backend_of_table[] = {
+	{ .compatible = "allwinner,sun5i-a13-display-backend" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, sun4i_backend_of_table);
+
+static struct platform_driver sun4i_backend_platform_driver = {
+	.probe		= sun4i_backend_probe,
+	.remove		= sun4i_backend_remove,
+	.driver		= {
+		.name		= "sun4i-backend",
+		.of_match_table	= sun4i_backend_of_table,
+	},
+};
+module_platform_driver(sun4i_backend_platform_driver);
+
+MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>");
+MODULE_DESCRIPTION("Allwinner A10 Display Backend Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/gpu/drm/sun4i/sun4i_backend.h b/drivers/gpu/drm/sun4i/sun4i_backend.h
new file mode 100644
index 000000000000..7070bb3434e5
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_backend.h
@@ -0,0 +1,165 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef _SUN4I_BACKEND_H_
+#define _SUN4I_BACKEND_H_
+
+#include <linux/clk.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#define SUN4I_BACKEND_MODCTL_REG		0x800
+#define SUN4I_BACKEND_MODCTL_LINE_SEL			BIT(29)
+#define SUN4I_BACKEND_MODCTL_ITLMOD_EN			BIT(28)
+#define SUN4I_BACKEND_MODCTL_OUT_SEL			GENMASK(22, 20)
+#define SUN4I_BACKEND_MODCTL_OUT_LCD				(0 << 20)
+#define SUN4I_BACKEND_MODCTL_OUT_FE0				(6 << 20)
+#define SUN4I_BACKEND_MODCTL_OUT_FE1				(7 << 20)
+#define SUN4I_BACKEND_MODCTL_HWC_EN			BIT(16)
+#define SUN4I_BACKEND_MODCTL_LAY_EN(l)			BIT(8 + l)
+#define SUN4I_BACKEND_MODCTL_OCSC_EN			BIT(5)
+#define SUN4I_BACKEND_MODCTL_DFLK_EN			BIT(4)
+#define SUN4I_BACKEND_MODCTL_DLP_START_CTL		BIT(2)
+#define SUN4I_BACKEND_MODCTL_START_CTL			BIT(1)
+#define SUN4I_BACKEND_MODCTL_DEBE_EN			BIT(0)
+
+#define SUN4I_BACKEND_BACKCOLOR_REG		0x804
+#define SUN4I_BACKEND_BACKCOLOR(r, g, b)		(((r) << 16) | ((g) << 8) | (b))
+
+#define SUN4I_BACKEND_DISSIZE_REG		0x808
+#define SUN4I_BACKEND_DISSIZE(w, h)			(((((h) - 1) & 0xffff) << 16) | \
+							 (((w) - 1) & 0xffff))
+
+#define SUN4I_BACKEND_LAYSIZE_REG(l)		(0x810 + (0x4 * (l)))
+#define SUN4I_BACKEND_LAYSIZE(w, h)			(((((h) - 1) & 0x1fff) << 16) | \
+							 (((w) - 1) & 0x1fff))
+
+#define SUN4I_BACKEND_LAYCOOR_REG(l)		(0x820 + (0x4 * (l)))
+#define SUN4I_BACKEND_LAYCOOR(x, y)			((((u32)(y) & 0xffff) << 16) | \
+							 ((u32)(x) & 0xffff))
+
+#define SUN4I_BACKEND_LAYLINEWIDTH_REG(l)	(0x840 + (0x4 * (l)))
+
+#define SUN4I_BACKEND_LAYFB_L32ADD_REG(l)	(0x850 + (0x4 * (l)))
+
+#define SUN4I_BACKEND_LAYFB_H4ADD_REG		0x860
+#define SUN4I_BACKEND_LAYFB_H4ADD_MSK(l)		GENMASK(3 + ((l) * 8), 0)
+#define SUN4I_BACKEND_LAYFB_H4ADD(l, val)			((val) << ((l) * 8))
+
+#define SUN4I_BACKEND_REGBUFFCTL_REG		0x870
+#define SUN4I_BACKEND_REGBUFFCTL_AUTOLOAD_DIS		BIT(1)
+#define SUN4I_BACKEND_REGBUFFCTL_LOADCTL		BIT(0)
+
+#define SUN4I_BACKEND_CKMAX_REG			0x880
+#define SUN4I_BACKEND_CKMIN_REG			0x884
+#define SUN4I_BACKEND_CKCFG_REG			0x888
+#define SUN4I_BACKEND_ATTCTL_REG0(l)		(0x890 + (0x4 * (l)))
+#define SUN4I_BACKEND_ATTCTL_REG0_LAY_PIPESEL_MASK	BIT(15)
+#define SUN4I_BACKEND_ATTCTL_REG0_LAY_PIPESEL(x)		((x) << 15)
+#define SUN4I_BACKEND_ATTCTL_REG0_LAY_PRISEL_MASK	GENMASK(11, 10)
+#define SUN4I_BACKEND_ATTCTL_REG0_LAY_PRISEL(x)			((x) << 10)
+
+#define SUN4I_BACKEND_ATTCTL_REG1(l)		(0x8a0 + (0x4 * (l)))
+#define SUN4I_BACKEND_ATTCTL_REG1_LAY_HSCAFCT		GENMASK(15, 14)
+#define SUN4I_BACKEND_ATTCTL_REG1_LAY_WSCAFCT		GENMASK(13, 12)
+#define SUN4I_BACKEND_ATTCTL_REG1_LAY_FBFMT		GENMASK(11, 8)
+#define SUN4I_BACKEND_LAY_FBFMT_1BPP				(0 << 8)
+#define SUN4I_BACKEND_LAY_FBFMT_2BPP				(1 << 8)
+#define SUN4I_BACKEND_LAY_FBFMT_4BPP				(2 << 8)
+#define SUN4I_BACKEND_LAY_FBFMT_8BPP				(3 << 8)
+#define SUN4I_BACKEND_LAY_FBFMT_RGB655				(4 << 8)
+#define SUN4I_BACKEND_LAY_FBFMT_RGB565				(5 << 8)
+#define SUN4I_BACKEND_LAY_FBFMT_RGB556				(6 << 8)
+#define SUN4I_BACKEND_LAY_FBFMT_ARGB1555			(7 << 8)
+#define SUN4I_BACKEND_LAY_FBFMT_RGBA5551			(8 << 8)
+#define SUN4I_BACKEND_LAY_FBFMT_XRGB8888			(9 << 8)
+#define SUN4I_BACKEND_LAY_FBFMT_ARGB8888			(10 << 8)
+#define SUN4I_BACKEND_LAY_FBFMT_RGB888				(11 << 8)
+#define SUN4I_BACKEND_LAY_FBFMT_ARGB4444			(12 << 8)
+#define SUN4I_BACKEND_LAY_FBFMT_RGBA4444			(13 << 8)
+
+#define SUN4I_BACKEND_DLCDPCTL_REG		0x8b0
+#define SUN4I_BACKEND_DLCDPFRMBUF_ADDRCTL_REG	0x8b4
+#define SUN4I_BACKEND_DLCDPCOOR_REG0		0x8b8
+#define SUN4I_BACKEND_DLCDPCOOR_REG1		0x8bc
+
+#define SUN4I_BACKEND_INT_EN_REG		0x8c0
+#define SUN4I_BACKEND_INT_FLAG_REG		0x8c4
+#define SUN4I_BACKEND_REG_LOAD_FINISHED			BIT(1)
+
+#define SUN4I_BACKEND_HWCCTL_REG		0x8d8
+#define SUN4I_BACKEND_HWCFBCTL_REG		0x8e0
+#define SUN4I_BACKEND_WBCTL_REG			0x8f0
+#define SUN4I_BACKEND_WBADD_REG			0x8f4
+#define SUN4I_BACKEND_WBLINEWIDTH_REG		0x8f8
+#define SUN4I_BACKEND_SPREN_REG			0x900
+#define SUN4I_BACKEND_SPRFMTCTL_REG		0x908
+#define SUN4I_BACKEND_SPRALPHACTL_REG		0x90c
+#define SUN4I_BACKEND_IYUVCTL_REG		0x920
+#define SUN4I_BACKEND_IYUVADD_REG(c)		(0x930 + (0x4 * (c)))
+#define SUN4I_BACKEND_IYUVLINEWITDTH_REG(c)	(0x940 + (0x4 * (c)))
+#define SUN4I_BACKEND_YGCOEF_REG(c)		(0x950 + (0x4 * (c)))
+#define SUN4I_BACKEND_YGCONS_REG		0x95c
+#define SUN4I_BACKEND_URCOEF_REG(c)		(0x960 + (0x4 * (c)))
+#define SUN4I_BACKEND_URCONS_REG		0x96c
+#define SUN4I_BACKEND_VBCOEF_REG(c)		(0x970 + (0x4 * (c)))
+#define SUN4I_BACKEND_VBCONS_REG		0x97c
+#define SUN4I_BACKEND_KSCTL_REG			0x980
+#define SUN4I_BACKEND_KSBKCOLOR_REG		0x984
+#define SUN4I_BACKEND_KSFSTLINEWIDTH_REG	0x988
+#define SUN4I_BACKEND_KSVSCAFCT_REG		0x98c
+#define SUN4I_BACKEND_KSHSCACOEF_REG(x)		(0x9a0 + (0x4 * (x)))
+#define SUN4I_BACKEND_OCCTL_REG			0x9c0
+#define SUN4I_BACKEND_OCCTL_ENABLE			BIT(0)
+
+#define SUN4I_BACKEND_OCRCOEF_REG(x)		(0x9d0 + (0x4 * (x)))
+#define SUN4I_BACKEND_OCRCONS_REG		0x9dc
+#define SUN4I_BACKEND_OCGCOEF_REG(x)		(0x9e0 + (0x4 * (x)))
+#define SUN4I_BACKEND_OCGCONS_REG		0x9ec
+#define SUN4I_BACKEND_OCBCOEF_REG(x)		(0x9f0 + (0x4 * (x)))
+#define SUN4I_BACKEND_OCBCONS_REG		0x9fc
+#define SUN4I_BACKEND_SPRCOORCTL_REG(s)		(0xa00 + (0x4 * (s)))
+#define SUN4I_BACKEND_SPRATTCTL_REG(s)		(0xb00 + (0x4 * (s)))
+#define SUN4I_BACKEND_SPRADD_REG(s)		(0xc00 + (0x4 * (s)))
+#define SUN4I_BACKEND_SPRLINEWIDTH_REG(s)	(0xd00 + (0x4 * (s)))
+
+#define SUN4I_BACKEND_SPRPALTAB_OFF		0x4000
+#define SUN4I_BACKEND_GAMMATAB_OFF		0x4400
+#define SUN4I_BACKEND_HWCPATTERN_OFF		0x4800
+#define SUN4I_BACKEND_HWCCOLORTAB_OFF		0x4c00
+#define SUN4I_BACKEND_PIPE_OFF(p)		(0x5000 + (0x400 * (p)))
+
+struct sun4i_backend {
+	struct regmap		*regs;
+
+	struct reset_control	*reset;
+
+	struct clk		*bus_clk;
+	struct clk		*mod_clk;
+	struct clk		*ram_clk;
+};
+
+void sun4i_backend_apply_color_correction(struct sun4i_backend *backend);
+void sun4i_backend_disable_color_correction(struct sun4i_backend *backend);
+
+void sun4i_backend_commit(struct sun4i_backend *backend);
+
+void sun4i_backend_layer_enable(struct sun4i_backend *backend,
+				int layer, bool enable);
+int sun4i_backend_update_layer_coord(struct sun4i_backend *backend,
+				     int layer, struct drm_plane *plane);
+int sun4i_backend_update_layer_formats(struct sun4i_backend *backend,
+				       int layer, struct drm_plane *plane);
+int sun4i_backend_update_layer_buffer(struct sun4i_backend *backend,
+				      int layer, struct drm_plane *plane);
+
+#endif /* _SUN4I_BACKEND_H_ */
diff --git a/drivers/gpu/drm/sun4i/sun4i_crtc.c b/drivers/gpu/drm/sun4i/sun4i_crtc.c
new file mode 100644
index 000000000000..4182a21f5923
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_crtc.c
@@ -0,0 +1,120 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <drm/drmP.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_modes.h>
+
+#include <linux/clk-provider.h>
+#include <linux/ioport.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/regmap.h>
+
+#include <video/videomode.h>
+
+#include "sun4i_backend.h"
+#include "sun4i_crtc.h"
+#include "sun4i_drv.h"
+#include "sun4i_tcon.h"
+
+static void sun4i_crtc_atomic_begin(struct drm_crtc *crtc,
+				    struct drm_crtc_state *old_state)
+{
+	struct sun4i_crtc *scrtc = drm_crtc_to_sun4i_crtc(crtc);
+	struct drm_device *dev = crtc->dev;
+	unsigned long flags;
+
+	if (crtc->state->event) {
+		WARN_ON(drm_crtc_vblank_get(crtc) != 0);
+
+		spin_lock_irqsave(&dev->event_lock, flags);
+		scrtc->event = crtc->state->event;
+		spin_unlock_irqrestore(&dev->event_lock, flags);
+		crtc->state->event = NULL;
+	 }
+}
+
+static void sun4i_crtc_atomic_flush(struct drm_crtc *crtc,
+				    struct drm_crtc_state *old_state)
+{
+	struct sun4i_crtc *scrtc = drm_crtc_to_sun4i_crtc(crtc);
+	struct sun4i_drv *drv = scrtc->drv;
+
+	DRM_DEBUG_DRIVER("Committing plane changes\n");
+
+	sun4i_backend_commit(drv->backend);
+}
+
+static void sun4i_crtc_disable(struct drm_crtc *crtc)
+{
+	struct sun4i_crtc *scrtc = drm_crtc_to_sun4i_crtc(crtc);
+	struct sun4i_drv *drv = scrtc->drv;
+
+	DRM_DEBUG_DRIVER("Disabling the CRTC\n");
+
+	sun4i_tcon_disable(drv->tcon);
+}
+
+static void sun4i_crtc_enable(struct drm_crtc *crtc)
+{
+	struct sun4i_crtc *scrtc = drm_crtc_to_sun4i_crtc(crtc);
+	struct sun4i_drv *drv = scrtc->drv;
+
+	DRM_DEBUG_DRIVER("Enabling the CRTC\n");
+
+	sun4i_tcon_enable(drv->tcon);
+}
+
+static const struct drm_crtc_helper_funcs sun4i_crtc_helper_funcs = {
+	.atomic_begin	= sun4i_crtc_atomic_begin,
+	.atomic_flush	= sun4i_crtc_atomic_flush,
+	.disable	= sun4i_crtc_disable,
+	.enable		= sun4i_crtc_enable,
+};
+
+static const struct drm_crtc_funcs sun4i_crtc_funcs = {
+	.atomic_destroy_state	= drm_atomic_helper_crtc_destroy_state,
+	.atomic_duplicate_state	= drm_atomic_helper_crtc_duplicate_state,
+	.destroy		= drm_crtc_cleanup,
+	.page_flip		= drm_atomic_helper_page_flip,
+	.reset			= drm_atomic_helper_crtc_reset,
+	.set_config		= drm_atomic_helper_set_config,
+};
+
+struct sun4i_crtc *sun4i_crtc_init(struct drm_device *drm)
+{
+	struct sun4i_drv *drv = drm->dev_private;
+	struct sun4i_crtc *scrtc;
+	int ret;
+
+	scrtc = devm_kzalloc(drm->dev, sizeof(*scrtc), GFP_KERNEL);
+	if (!scrtc)
+		return NULL;
+	scrtc->drv = drv;
+
+	ret = drm_crtc_init_with_planes(drm, &scrtc->crtc,
+					drv->primary,
+					NULL,
+					&sun4i_crtc_funcs,
+					NULL);
+	if (ret) {
+		dev_err(drm->dev, "Couldn't init DRM CRTC\n");
+		return NULL;
+	}
+
+	drm_crtc_helper_add(&scrtc->crtc, &sun4i_crtc_helper_funcs);
+
+	return scrtc;
+}
diff --git a/drivers/gpu/drm/sun4i/sun4i_crtc.h b/drivers/gpu/drm/sun4i/sun4i_crtc.h
new file mode 100644
index 000000000000..dec8ce4d9b25
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_crtc.h
@@ -0,0 +1,30 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef _SUN4I_CRTC_H_
+#define _SUN4I_CRTC_H_
+
+struct sun4i_crtc {
+	struct drm_crtc			crtc;
+	struct drm_pending_vblank_event	*event;
+
+	struct sun4i_drv		*drv;
+};
+
+static inline struct sun4i_crtc *drm_crtc_to_sun4i_crtc(struct drm_crtc *crtc)
+{
+	return container_of(crtc, struct sun4i_crtc, crtc);
+}
+
+struct sun4i_crtc *sun4i_crtc_init(struct drm_device *drm);
+
+#endif /* _SUN4I_CRTC_H_ */
diff --git a/drivers/gpu/drm/sun4i/sun4i_dotclock.c b/drivers/gpu/drm/sun4i/sun4i_dotclock.c
new file mode 100644
index 000000000000..3ff668cb463c
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_dotclock.c
@@ -0,0 +1,160 @@
+/*
+ * Copyright (C) 2016 Free Electrons
+ * Copyright (C) 2016 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/regmap.h>
+
+#include "sun4i_tcon.h"
+
+struct sun4i_dclk {
+	struct clk_hw	hw;
+	struct regmap	*regmap;
+};
+
+static inline struct sun4i_dclk *hw_to_dclk(struct clk_hw *hw)
+{
+	return container_of(hw, struct sun4i_dclk, hw);
+}
+
+static void sun4i_dclk_disable(struct clk_hw *hw)
+{
+	struct sun4i_dclk *dclk = hw_to_dclk(hw);
+
+	regmap_update_bits(dclk->regmap, SUN4I_TCON0_DCLK_REG,
+			   BIT(SUN4I_TCON0_DCLK_GATE_BIT), 0);
+}
+
+static int sun4i_dclk_enable(struct clk_hw *hw)
+{
+	struct sun4i_dclk *dclk = hw_to_dclk(hw);
+
+	return regmap_update_bits(dclk->regmap, SUN4I_TCON0_DCLK_REG,
+				  BIT(SUN4I_TCON0_DCLK_GATE_BIT),
+				  BIT(SUN4I_TCON0_DCLK_GATE_BIT));
+}
+
+static int sun4i_dclk_is_enabled(struct clk_hw *hw)
+{
+	struct sun4i_dclk *dclk = hw_to_dclk(hw);
+	u32 val;
+
+	regmap_read(dclk->regmap, SUN4I_TCON0_DCLK_REG, &val);
+
+	return val & BIT(SUN4I_TCON0_DCLK_GATE_BIT);
+}
+
+static unsigned long sun4i_dclk_recalc_rate(struct clk_hw *hw,
+					    unsigned long parent_rate)
+{
+	struct sun4i_dclk *dclk = hw_to_dclk(hw);
+	u32 val;
+
+	regmap_read(dclk->regmap, SUN4I_TCON0_DCLK_REG, &val);
+
+	val >>= SUN4I_TCON0_DCLK_DIV_SHIFT;
+	val &= SUN4I_TCON0_DCLK_DIV_WIDTH;
+
+	if (!val)
+		val = 1;
+
+	return parent_rate / val;
+}
+
+static long sun4i_dclk_round_rate(struct clk_hw *hw, unsigned long rate,
+				  unsigned long *parent_rate)
+{
+	return *parent_rate / DIV_ROUND_CLOSEST(*parent_rate, rate);
+}
+
+static int sun4i_dclk_set_rate(struct clk_hw *hw, unsigned long rate,
+			       unsigned long parent_rate)
+{
+	struct sun4i_dclk *dclk = hw_to_dclk(hw);
+	int div = DIV_ROUND_CLOSEST(parent_rate, rate);
+
+	return regmap_update_bits(dclk->regmap, SUN4I_TCON0_DCLK_REG,
+				  GENMASK(6, 0), div);
+}
+
+static int sun4i_dclk_get_phase(struct clk_hw *hw)
+{
+	struct sun4i_dclk *dclk = hw_to_dclk(hw);
+	u32 val;
+
+	regmap_read(dclk->regmap, SUN4I_TCON0_IO_POL_REG, &val);
+
+	val >>= 28;
+	val &= 3;
+
+	return val * 120;
+}
+
+static int sun4i_dclk_set_phase(struct clk_hw *hw, int degrees)
+{
+	struct sun4i_dclk *dclk = hw_to_dclk(hw);
+
+	regmap_update_bits(dclk->regmap, SUN4I_TCON0_IO_POL_REG,
+			   GENMASK(29, 28),
+			   degrees / 120);
+
+	return 0;
+}
+
+static const struct clk_ops sun4i_dclk_ops = {
+	.disable	= sun4i_dclk_disable,
+	.enable		= sun4i_dclk_enable,
+	.is_enabled	= sun4i_dclk_is_enabled,
+
+	.recalc_rate	= sun4i_dclk_recalc_rate,
+	.round_rate	= sun4i_dclk_round_rate,
+	.set_rate	= sun4i_dclk_set_rate,
+
+	.get_phase	= sun4i_dclk_get_phase,
+	.set_phase	= sun4i_dclk_set_phase,
+};
+
+int sun4i_dclk_create(struct device *dev, struct sun4i_tcon *tcon)
+{
+	const char *clk_name, *parent_name;
+	struct clk_init_data init;
+	struct sun4i_dclk *dclk;
+
+	parent_name = __clk_get_name(tcon->sclk0);
+	of_property_read_string_index(dev->of_node, "clock-output-names", 0,
+				      &clk_name);
+
+	dclk = devm_kzalloc(dev, sizeof(*dclk), GFP_KERNEL);
+	if (!dclk)
+		return -ENOMEM;
+
+	init.name = clk_name;
+	init.ops = &sun4i_dclk_ops;
+	init.parent_names = &parent_name;
+	init.num_parents = 1;
+
+	dclk->regmap = tcon->regs;
+	dclk->hw.init = &init;
+
+	tcon->dclk = clk_register(dev, &dclk->hw);
+	if (IS_ERR(tcon->dclk))
+		return PTR_ERR(tcon->dclk);
+
+	return 0;
+}
+EXPORT_SYMBOL(sun4i_dclk_create);
+
+int sun4i_dclk_free(struct sun4i_tcon *tcon)
+{
+	clk_unregister(tcon->dclk);
+	return 0;
+}
+EXPORT_SYMBOL(sun4i_dclk_free);
diff --git a/drivers/gpu/drm/sun4i/sun4i_dotclock.h b/drivers/gpu/drm/sun4i/sun4i_dotclock.h
new file mode 100644
index 000000000000..d5e25fa9eff1
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_dotclock.h
@@ -0,0 +1,21 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef _SUN4I_DOTCLOCK_H_
+#define _SUN4I_DOTCLOCK_H_
+
+struct sun4i_tcon;
+
+int sun4i_dclk_create(struct device *dev, struct sun4i_tcon *tcon);
+int sun4i_dclk_free(struct sun4i_tcon *tcon);
+
+#endif /* _SUN4I_DOTCLOCK_H_ */
diff --git a/drivers/gpu/drm/sun4i/sun4i_drv.c b/drivers/gpu/drm/sun4i/sun4i_drv.c
new file mode 100644
index 000000000000..5c64d2105dc7
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_drv.c
@@ -0,0 +1,319 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/component.h>
+#include <linux/of_graph.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_fb_cma_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+
+#include "sun4i_crtc.h"
+#include "sun4i_drv.h"
+#include "sun4i_framebuffer.h"
+#include "sun4i_layer.h"
+#include "sun4i_tcon.h"
+
+static int sun4i_drv_connector_plug_all(struct drm_device *drm)
+{
+	struct drm_connector *connector, *failed;
+	int ret;
+
+	mutex_lock(&drm->mode_config.mutex);
+	list_for_each_entry(connector, &drm->mode_config.connector_list, head) {
+		ret = drm_connector_register(connector);
+		if (ret) {
+			failed = connector;
+			goto err;
+		}
+	}
+	mutex_unlock(&drm->mode_config.mutex);
+	return 0;
+
+err:
+	list_for_each_entry(connector, &drm->mode_config.connector_list, head) {
+		if (failed == connector)
+			break;
+
+		drm_connector_unregister(connector);
+	}
+	mutex_unlock(&drm->mode_config.mutex);
+
+	return ret;
+}
+
+static int sun4i_drv_enable_vblank(struct drm_device *drm, unsigned int pipe)
+{
+	struct sun4i_drv *drv = drm->dev_private;
+	struct sun4i_tcon *tcon = drv->tcon;
+
+	DRM_DEBUG_DRIVER("Enabling VBLANK on pipe %d\n", pipe);
+
+	sun4i_tcon_enable_vblank(tcon, true);
+
+	return 0;
+}
+
+static void sun4i_drv_disable_vblank(struct drm_device *drm, unsigned int pipe)
+{
+	struct sun4i_drv *drv = drm->dev_private;
+	struct sun4i_tcon *tcon = drv->tcon;
+
+	DRM_DEBUG_DRIVER("Disabling VBLANK on pipe %d\n", pipe);
+
+	sun4i_tcon_enable_vblank(tcon, false);
+}
+
+static const struct file_operations sun4i_drv_fops = {
+	.owner		= THIS_MODULE,
+	.open		= drm_open,
+	.release	= drm_release,
+	.unlocked_ioctl	= drm_ioctl,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl	= drm_compat_ioctl,
+#endif
+	.poll		= drm_poll,
+	.read		= drm_read,
+	.llseek		= no_llseek,
+	.mmap		= drm_gem_cma_mmap,
+};
+
+static struct drm_driver sun4i_drv_driver = {
+	.driver_features	= DRIVER_GEM | DRIVER_MODESET | DRIVER_PRIME | DRIVER_ATOMIC,
+
+	/* Generic Operations */
+	.fops			= &sun4i_drv_fops,
+	.name			= "sun4i-drm",
+	.desc			= "Allwinner sun4i Display Engine",
+	.date			= "20150629",
+	.major			= 1,
+	.minor			= 0,
+
+	/* GEM Operations */
+	.dumb_create		= drm_gem_cma_dumb_create,
+	.dumb_destroy		= drm_gem_dumb_destroy,
+	.dumb_map_offset	= drm_gem_cma_dumb_map_offset,
+	.gem_free_object	= drm_gem_cma_free_object,
+	.gem_vm_ops		= &drm_gem_cma_vm_ops,
+
+	/* PRIME Operations */
+	.prime_handle_to_fd	= drm_gem_prime_handle_to_fd,
+	.prime_fd_to_handle	= drm_gem_prime_fd_to_handle,
+	.gem_prime_import	= drm_gem_prime_import,
+	.gem_prime_export	= drm_gem_prime_export,
+	.gem_prime_get_sg_table	= drm_gem_cma_prime_get_sg_table,
+	.gem_prime_import_sg_table = drm_gem_cma_prime_import_sg_table,
+	.gem_prime_vmap		= drm_gem_cma_prime_vmap,
+	.gem_prime_vunmap	= drm_gem_cma_prime_vunmap,
+	.gem_prime_mmap		= drm_gem_cma_prime_mmap,
+
+	/* Frame Buffer Operations */
+
+	/* VBlank Operations */
+	.get_vblank_counter	= drm_vblank_count,
+	.enable_vblank		= sun4i_drv_enable_vblank,
+	.disable_vblank		= sun4i_drv_disable_vblank,
+};
+
+static int sun4i_drv_bind(struct device *dev)
+{
+	struct drm_device *drm;
+	struct sun4i_drv *drv;
+	int ret;
+
+	drm = drm_dev_alloc(&sun4i_drv_driver, dev);
+	if (!drm)
+		return -ENOMEM;
+
+	ret = drm_dev_set_unique(drm, dev_name(drm->dev));
+	if (ret)
+		goto free_drm;
+
+	drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL);
+	if (!drv) {
+		ret = -ENOMEM;
+		goto free_drm;
+	}
+	drm->dev_private = drv;
+
+	drm_vblank_init(drm, 1);
+	drm_mode_config_init(drm);
+
+	ret = component_bind_all(drm->dev, drm);
+	if (ret) {
+		dev_err(drm->dev, "Couldn't bind all pipelines components\n");
+		goto free_drm;
+	}
+
+	/* Create our layers */
+	drv->layers = sun4i_layers_init(drm);
+	if (!drv->layers) {
+		dev_err(drm->dev, "Couldn't create the planes\n");
+		ret = -EINVAL;
+		goto free_drm;
+	}
+
+	/* Create our CRTC */
+	drv->crtc = sun4i_crtc_init(drm);
+	if (!drv->crtc) {
+		dev_err(drm->dev, "Couldn't create the CRTC\n");
+		ret = -EINVAL;
+		goto free_drm;
+	}
+	drm->irq_enabled = true;
+
+	/* Create our framebuffer */
+	drv->fbdev = sun4i_framebuffer_init(drm);
+	if (IS_ERR(drv->fbdev)) {
+		dev_err(drm->dev, "Couldn't create our framebuffer\n");
+		ret = PTR_ERR(drv->fbdev);
+		goto free_drm;
+	}
+
+	/* Enable connectors polling */
+	drm_kms_helper_poll_init(drm);
+
+	ret = drm_dev_register(drm, 0);
+	if (ret)
+		goto free_drm;
+
+	ret = sun4i_drv_connector_plug_all(drm);
+	if (ret)
+		goto unregister_drm;
+
+	return 0;
+
+unregister_drm:
+	drm_dev_unregister(drm);
+free_drm:
+	drm_dev_unref(drm);
+	return ret;
+}
+
+static void sun4i_drv_unbind(struct device *dev)
+{
+	struct drm_device *drm = dev_get_drvdata(dev);
+
+	drm_dev_unregister(drm);
+	drm_kms_helper_poll_fini(drm);
+	sun4i_framebuffer_free(drm);
+	drm_vblank_cleanup(drm);
+	drm_dev_unref(drm);
+}
+
+static const struct component_master_ops sun4i_drv_master_ops = {
+	.bind	= sun4i_drv_bind,
+	.unbind	= sun4i_drv_unbind,
+};
+
+static int compare_of(struct device *dev, void *data)
+{
+	DRM_DEBUG_DRIVER("Comparing of node %s with %s\n",
+			 of_node_full_name(dev->of_node),
+			 of_node_full_name(data));
+
+	return dev->of_node == data;
+}
+
+static int sun4i_drv_add_endpoints(struct device *dev,
+				   struct component_match **match,
+				   struct device_node *node)
+{
+	struct device_node *port, *ep, *remote;
+	int count = 0;
+
+	/* Add current component */
+	component_match_add(dev, match, compare_of, node);
+	count++;
+
+	/* Inputs are listed first, then outputs */
+	port = of_graph_get_port_by_id(node, 1);
+	if (!port) {
+		DRM_DEBUG_DRIVER("No output to bind\n");
+		return count;
+	}
+
+	for_each_available_child_of_node(port, ep) {
+		remote = of_graph_get_remote_port_parent(ep);
+		if (!remote) {
+			DRM_DEBUG_DRIVER("Error retrieving the output node\n");
+			of_node_put(remote);
+			continue;
+		}
+
+		/* Walk down our tree */
+		count += sun4i_drv_add_endpoints(dev, match, remote);
+
+		of_node_put(remote);
+	}
+
+	return count;
+}
+
+static int sun4i_drv_probe(struct platform_device *pdev)
+{
+	struct component_match *match = NULL;
+	struct device_node *np = pdev->dev.of_node;
+	int i, count = 0;
+
+	for (i = 0;; i++) {
+		struct device_node *pipeline = of_parse_phandle(np, "pipelines",
+								i);
+		if (!pipeline)
+			break;
+
+		if (!of_device_is_available(pipeline)) {
+			of_node_put(pipeline);
+			continue;
+		}
+
+		count += sun4i_drv_add_endpoints(&pdev->dev, &match,
+						pipeline);
+
+		DRM_DEBUG_DRIVER("Queued %d outputs on pipeline %d\n",
+				 count, i);
+	}
+
+	if (count)
+		return component_master_add_with_match(&pdev->dev,
+						       &sun4i_drv_master_ops,
+						       match);
+	else
+		return 0;
+}
+
+static int sun4i_drv_remove(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static const struct of_device_id sun4i_drv_of_table[] = {
+	{ .compatible = "allwinner,sun5i-a13-display-engine" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, sun4i_drv_of_table);
+
+static struct platform_driver sun4i_drv_platform_driver = {
+	.probe		= sun4i_drv_probe,
+	.remove		= sun4i_drv_remove,
+	.driver		= {
+		.name		= "sun4i-drm",
+		.of_match_table	= sun4i_drv_of_table,
+	},
+};
+module_platform_driver(sun4i_drv_platform_driver);
+
+MODULE_AUTHOR("Boris Brezillon <boris.brezillon@free-electrons.com>");
+MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>");
+MODULE_DESCRIPTION("Allwinner A10 Display Engine DRM/KMS Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/gpu/drm/sun4i/sun4i_drv.h b/drivers/gpu/drm/sun4i/sun4i_drv.h
new file mode 100644
index 000000000000..597353eab728
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_drv.h
@@ -0,0 +1,30 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef _SUN4I_DRV_H_
+#define _SUN4I_DRV_H_
+
+#include <linux/clk.h>
+#include <linux/regmap.h>
+
+struct sun4i_drv {
+	struct sun4i_backend	*backend;
+	struct sun4i_crtc	*crtc;
+	struct sun4i_tcon	*tcon;
+
+	struct drm_plane	*primary;
+	struct drm_fbdev_cma	*fbdev;
+
+	struct sun4i_layer	**layers;
+};
+
+#endif /* _SUN4I_DRV_H_ */
diff --git a/drivers/gpu/drm/sun4i/sun4i_framebuffer.c b/drivers/gpu/drm/sun4i/sun4i_framebuffer.c
new file mode 100644
index 000000000000..a0b30c216a5b
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_framebuffer.c
@@ -0,0 +1,54 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_fb_cma_helper.h>
+#include <drm/drmP.h>
+
+#include "sun4i_drv.h"
+
+static void sun4i_de_output_poll_changed(struct drm_device *drm)
+{
+	struct sun4i_drv *drv = drm->dev_private;
+
+	if (drv->fbdev)
+		drm_fbdev_cma_hotplug_event(drv->fbdev);
+}
+
+static const struct drm_mode_config_funcs sun4i_de_mode_config_funcs = {
+	.output_poll_changed	= sun4i_de_output_poll_changed,
+	.atomic_check		= drm_atomic_helper_check,
+	.atomic_commit		= drm_atomic_helper_commit,
+	.fb_create		= drm_fb_cma_create,
+};
+
+struct drm_fbdev_cma *sun4i_framebuffer_init(struct drm_device *drm)
+{
+	drm_mode_config_reset(drm);
+
+	drm->mode_config.max_width = 8192;
+	drm->mode_config.max_height = 8192;
+
+	drm->mode_config.funcs = &sun4i_de_mode_config_funcs;
+
+	return drm_fbdev_cma_init(drm, 32,
+				  drm->mode_config.num_crtc,
+				  drm->mode_config.num_connector);
+}
+
+void sun4i_framebuffer_free(struct drm_device *drm)
+{
+	struct sun4i_drv *drv = drm->dev_private;
+
+	drm_fbdev_cma_fini(drv->fbdev);
+	drm_mode_config_cleanup(drm);
+}
diff --git a/drivers/gpu/drm/sun4i/sun4i_framebuffer.h b/drivers/gpu/drm/sun4i/sun4i_framebuffer.h
new file mode 100644
index 000000000000..3afd65252ee0
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_framebuffer.h
@@ -0,0 +1,19 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef _SUN4I_FRAMEBUFFER_H_
+#define _SUN4I_FRAMEBUFFER_H_
+
+struct drm_fbdev_cma *sun4i_framebuffer_init(struct drm_device *drm);
+void sun4i_framebuffer_free(struct drm_device *drm);
+
+#endif /* _SUN4I_FRAMEBUFFER_H_ */
diff --git a/drivers/gpu/drm/sun4i/sun4i_layer.c b/drivers/gpu/drm/sun4i/sun4i_layer.c
new file mode 100644
index 000000000000..068ab806309b
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_layer.c
@@ -0,0 +1,161 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_plane_helper.h>
+#include <drm/drmP.h>
+
+#include "sun4i_backend.h"
+#include "sun4i_drv.h"
+#include "sun4i_layer.h"
+
+#define SUN4I_NUM_LAYERS	2
+
+static int sun4i_backend_layer_atomic_check(struct drm_plane *plane,
+					    struct drm_plane_state *state)
+{
+	return 0;
+}
+
+static void sun4i_backend_layer_atomic_disable(struct drm_plane *plane,
+					       struct drm_plane_state *old_state)
+{
+	struct sun4i_layer *layer = plane_to_sun4i_layer(plane);
+	struct sun4i_drv *drv = layer->drv;
+	struct sun4i_backend *backend = drv->backend;
+
+	sun4i_backend_layer_enable(backend, layer->id, false);
+}
+
+static void sun4i_backend_layer_atomic_update(struct drm_plane *plane,
+					      struct drm_plane_state *old_state)
+{
+	struct sun4i_layer *layer = plane_to_sun4i_layer(plane);
+	struct sun4i_drv *drv = layer->drv;
+	struct sun4i_backend *backend = drv->backend;
+
+	sun4i_backend_update_layer_coord(backend, layer->id, plane);
+	sun4i_backend_update_layer_formats(backend, layer->id, plane);
+	sun4i_backend_update_layer_buffer(backend, layer->id, plane);
+	sun4i_backend_layer_enable(backend, layer->id, true);
+}
+
+static struct drm_plane_helper_funcs sun4i_backend_layer_helper_funcs = {
+	.atomic_check	= sun4i_backend_layer_atomic_check,
+	.atomic_disable	= sun4i_backend_layer_atomic_disable,
+	.atomic_update	= sun4i_backend_layer_atomic_update,
+};
+
+static const struct drm_plane_funcs sun4i_backend_layer_funcs = {
+	.atomic_destroy_state	= drm_atomic_helper_plane_destroy_state,
+	.atomic_duplicate_state	= drm_atomic_helper_plane_duplicate_state,
+	.destroy		= drm_plane_cleanup,
+	.disable_plane		= drm_atomic_helper_disable_plane,
+	.reset			= drm_atomic_helper_plane_reset,
+	.update_plane		= drm_atomic_helper_update_plane,
+};
+
+static const uint32_t sun4i_backend_layer_formats[] = {
+	DRM_FORMAT_ARGB8888,
+	DRM_FORMAT_XRGB8888,
+	DRM_FORMAT_RGB888,
+};
+
+static struct sun4i_layer *sun4i_layer_init_one(struct drm_device *drm,
+						enum drm_plane_type type)
+{
+	struct sun4i_drv *drv = drm->dev_private;
+	struct sun4i_layer *layer;
+	int ret;
+
+	layer = devm_kzalloc(drm->dev, sizeof(*layer), GFP_KERNEL);
+	if (!layer)
+		return ERR_PTR(-ENOMEM);
+
+	ret = drm_universal_plane_init(drm, &layer->plane, BIT(0),
+				       &sun4i_backend_layer_funcs,
+				       sun4i_backend_layer_formats,
+				       ARRAY_SIZE(sun4i_backend_layer_formats),
+				       type,
+				       NULL);
+	if (ret) {
+		dev_err(drm->dev, "Couldn't initialize layer\n");
+		return ERR_PTR(ret);
+	}
+
+	drm_plane_helper_add(&layer->plane,
+			     &sun4i_backend_layer_helper_funcs);
+	layer->drv = drv;
+
+	if (type == DRM_PLANE_TYPE_PRIMARY)
+		drv->primary = &layer->plane;
+
+	return layer;
+}
+
+struct sun4i_layer **sun4i_layers_init(struct drm_device *drm)
+{
+	struct sun4i_drv *drv = drm->dev_private;
+	struct sun4i_layer **layers;
+	int i;
+
+	layers = devm_kcalloc(drm->dev, SUN4I_NUM_LAYERS, sizeof(**layers),
+			      GFP_KERNEL);
+	if (!layers)
+		return ERR_PTR(-ENOMEM);
+
+	/*
+	 * The hardware is a bit unusual here.
+	 *
+	 * Even though it supports 4 layers, it does the composition
+	 * in two separate steps.
+	 *
+	 * The first one is assigning a layer to one of its two
+	 * pipes. If more that 1 layer is assigned to the same pipe,
+	 * and if pixels overlaps, the pipe will take the pixel from
+	 * the layer with the highest priority.
+	 *
+	 * The second step is the actual alpha blending, that takes
+	 * the two pipes as input, and uses the eventual alpha
+	 * component to do the transparency between the two.
+	 *
+	 * This two steps scenario makes us unable to guarantee a
+	 * robust alpha blending between the 4 layers in all
+	 * situations. So we just expose two layers, one per pipe. On
+	 * SoCs that support it, sprites could fill the need for more
+	 * layers.
+	 */
+	for (i = 0; i < SUN4I_NUM_LAYERS; i++) {
+		enum drm_plane_type type = (i == 0)
+					 ? DRM_PLANE_TYPE_PRIMARY
+					 : DRM_PLANE_TYPE_OVERLAY;
+		struct sun4i_layer *layer = layers[i];
+
+		layer = sun4i_layer_init_one(drm, type);
+		if (IS_ERR(layer)) {
+			dev_err(drm->dev, "Couldn't initialize %s plane\n",
+				i ? "overlay" : "primary");
+			return ERR_CAST(layer);
+		};
+
+		DRM_DEBUG_DRIVER("Assigning %s plane to pipe %d\n",
+				 i ? "overlay" : "primary", i);
+		regmap_update_bits(drv->backend->regs, SUN4I_BACKEND_ATTCTL_REG0(i),
+				   SUN4I_BACKEND_ATTCTL_REG0_LAY_PIPESEL_MASK,
+				   SUN4I_BACKEND_ATTCTL_REG0_LAY_PIPESEL(i));
+
+		layer->id = i;
+	};
+
+	return layers;
+}
diff --git a/drivers/gpu/drm/sun4i/sun4i_layer.h b/drivers/gpu/drm/sun4i/sun4i_layer.h
new file mode 100644
index 000000000000..a2f65d7a3f4e
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_layer.h
@@ -0,0 +1,30 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef _SUN4I_LAYER_H_
+#define _SUN4I_LAYER_H_
+
+struct sun4i_layer {
+	struct drm_plane	plane;
+	struct sun4i_drv	*drv;
+	int			id;
+};
+
+static inline struct sun4i_layer *
+plane_to_sun4i_layer(struct drm_plane *plane)
+{
+	return container_of(plane, struct sun4i_layer, plane);
+}
+
+struct sun4i_layer **sun4i_layers_init(struct drm_device *drm);
+
+#endif /* _SUN4I_LAYER_H_ */
diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c b/drivers/gpu/drm/sun4i/sun4i_tcon.c
new file mode 100644
index 000000000000..b6e57ed79df4
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
@@ -0,0 +1,492 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <drm/drmP.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_modes.h>
+
+#include <linux/component.h>
+#include <linux/ioport.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include "sun4i_crtc.h"
+#include "sun4i_dotclock.h"
+#include "sun4i_drv.h"
+#include "sun4i_tcon.h"
+
+void sun4i_tcon_disable(struct sun4i_tcon *tcon)
+{
+	DRM_DEBUG_DRIVER("Disabling TCON\n");
+
+	/* Disable the TCON */
+	regmap_update_bits(tcon->regs, SUN4I_TCON_GCTL_REG,
+			   SUN4I_TCON_GCTL_TCON_ENABLE, 0);
+}
+EXPORT_SYMBOL(sun4i_tcon_disable);
+
+void sun4i_tcon_enable(struct sun4i_tcon *tcon)
+{
+	DRM_DEBUG_DRIVER("Enabling TCON\n");
+
+	/* Enable the TCON */
+	regmap_update_bits(tcon->regs, SUN4I_TCON_GCTL_REG,
+			   SUN4I_TCON_GCTL_TCON_ENABLE,
+			   SUN4I_TCON_GCTL_TCON_ENABLE);
+}
+EXPORT_SYMBOL(sun4i_tcon_enable);
+
+void sun4i_tcon_channel_disable(struct sun4i_tcon *tcon, int channel)
+{
+	/* Disable the TCON's channel */
+	if (channel == 0) {
+		regmap_update_bits(tcon->regs, SUN4I_TCON0_CTL_REG,
+				   SUN4I_TCON0_CTL_TCON_ENABLE, 0);
+		clk_disable_unprepare(tcon->dclk);
+	} else if (channel == 1) {
+		regmap_update_bits(tcon->regs, SUN4I_TCON1_CTL_REG,
+				   SUN4I_TCON1_CTL_TCON_ENABLE, 0);
+		clk_disable_unprepare(tcon->sclk1);
+	}
+}
+EXPORT_SYMBOL(sun4i_tcon_channel_disable);
+
+void sun4i_tcon_channel_enable(struct sun4i_tcon *tcon, int channel)
+{
+	/* Enable the TCON's channel */
+	if (channel == 0) {
+		regmap_update_bits(tcon->regs, SUN4I_TCON0_CTL_REG,
+				   SUN4I_TCON0_CTL_TCON_ENABLE,
+				   SUN4I_TCON0_CTL_TCON_ENABLE);
+		clk_prepare_enable(tcon->dclk);
+	} else if (channel == 1) {
+		regmap_update_bits(tcon->regs, SUN4I_TCON1_CTL_REG,
+				   SUN4I_TCON1_CTL_TCON_ENABLE,
+				   SUN4I_TCON1_CTL_TCON_ENABLE);
+		clk_prepare_enable(tcon->sclk1);
+	}
+}
+EXPORT_SYMBOL(sun4i_tcon_channel_enable);
+
+void sun4i_tcon_enable_vblank(struct sun4i_tcon *tcon, bool enable)
+{
+	u32 mask, val = 0;
+
+	DRM_DEBUG_DRIVER("%sabling VBLANK interrupt\n", enable ? "En" : "Dis");
+
+	mask = SUN4I_TCON_GINT0_VBLANK_ENABLE(0) |
+	       SUN4I_TCON_GINT0_VBLANK_ENABLE(1);
+
+	if (enable)
+		val = mask;
+
+	regmap_update_bits(tcon->regs, SUN4I_TCON_GINT0_REG, mask, val);
+}
+EXPORT_SYMBOL(sun4i_tcon_enable_vblank);
+
+static int sun4i_tcon_get_clk_delay(struct drm_display_mode *mode,
+				    int channel)
+{
+	int delay = mode->vtotal - mode->vdisplay;
+
+	if (mode->flags & DRM_MODE_FLAG_INTERLACE)
+		delay /= 2;
+
+	if (channel == 1)
+		delay -= 2;
+
+	delay = min(delay, 30);
+
+	DRM_DEBUG_DRIVER("TCON %d clock delay %u\n", channel, delay);
+
+	return delay;
+}
+
+void sun4i_tcon0_mode_set(struct sun4i_tcon *tcon,
+			  struct drm_display_mode *mode)
+{
+	unsigned int bp, hsync, vsync;
+	u8 clk_delay;
+	u32 val = 0;
+
+	/* Adjust clock delay */
+	clk_delay = sun4i_tcon_get_clk_delay(mode, 1);
+	regmap_update_bits(tcon->regs, SUN4I_TCON0_CTL_REG,
+			   SUN4I_TCON0_CTL_CLK_DELAY_MASK,
+			   SUN4I_TCON0_CTL_CLK_DELAY(clk_delay));
+
+	/* Set the resolution */
+	regmap_write(tcon->regs, SUN4I_TCON0_BASIC0_REG,
+		     SUN4I_TCON0_BASIC0_X(mode->crtc_hdisplay) |
+		     SUN4I_TCON0_BASIC0_Y(mode->crtc_vdisplay));
+
+	/* Set horizontal display timings */
+	bp = mode->crtc_htotal - mode->crtc_hsync_end;
+	DRM_DEBUG_DRIVER("Setting horizontal total %d, backporch %d\n",
+			 mode->crtc_htotal, bp);
+	regmap_write(tcon->regs, SUN4I_TCON0_BASIC1_REG,
+		     SUN4I_TCON0_BASIC1_H_TOTAL(mode->crtc_htotal) |
+		     SUN4I_TCON0_BASIC1_H_BACKPORCH(bp));
+
+	/* Set vertical display timings */
+	bp = mode->crtc_vtotal - mode->crtc_vsync_end;
+	DRM_DEBUG_DRIVER("Setting vertical total %d, backporch %d\n",
+			 mode->crtc_vtotal, bp);
+	regmap_write(tcon->regs, SUN4I_TCON0_BASIC2_REG,
+		     SUN4I_TCON0_BASIC2_V_TOTAL(mode->crtc_vtotal) |
+		     SUN4I_TCON0_BASIC2_V_BACKPORCH(bp));
+
+	/* Set Hsync and Vsync length */
+	hsync = mode->crtc_hsync_end - mode->crtc_hsync_start;
+	vsync = mode->crtc_vsync_end - mode->crtc_vsync_start;
+	DRM_DEBUG_DRIVER("Setting HSYNC %d, VSYNC %d\n", hsync, vsync);
+	regmap_write(tcon->regs, SUN4I_TCON0_BASIC3_REG,
+		     SUN4I_TCON0_BASIC3_V_SYNC(vsync) |
+		     SUN4I_TCON0_BASIC3_H_SYNC(hsync));
+
+	/* Setup the polarity of the various signals */
+	if (!(mode->flags & DRM_MODE_FLAG_PHSYNC))
+		val |= SUN4I_TCON0_IO_POL_HSYNC_POSITIVE;
+
+	if (!(mode->flags & DRM_MODE_FLAG_PVSYNC))
+		val |= SUN4I_TCON0_IO_POL_VSYNC_POSITIVE;
+
+	regmap_update_bits(tcon->regs, SUN4I_TCON0_IO_POL_REG,
+			   SUN4I_TCON0_IO_POL_HSYNC_POSITIVE | SUN4I_TCON0_IO_POL_VSYNC_POSITIVE,
+			   val);
+
+	/* Map output pins to channel 0 */
+	regmap_update_bits(tcon->regs, SUN4I_TCON_GCTL_REG,
+			   SUN4I_TCON_GCTL_IOMAP_MASK,
+			   SUN4I_TCON_GCTL_IOMAP_TCON0);
+
+	/* Enable the output on the pins */
+	regmap_write(tcon->regs, SUN4I_TCON0_IO_TRI_REG, 0);
+}
+EXPORT_SYMBOL(sun4i_tcon0_mode_set);
+
+void sun4i_tcon1_mode_set(struct sun4i_tcon *tcon,
+			  struct drm_display_mode *mode)
+{
+	unsigned int bp, hsync, vsync;
+	u8 clk_delay;
+	u32 val;
+
+	/* Adjust clock delay */
+	clk_delay = sun4i_tcon_get_clk_delay(mode, 1);
+	regmap_update_bits(tcon->regs, SUN4I_TCON1_CTL_REG,
+			   SUN4I_TCON1_CTL_CLK_DELAY_MASK,
+			   SUN4I_TCON1_CTL_CLK_DELAY(clk_delay));
+
+	/* Set interlaced mode */
+	if (mode->flags & DRM_MODE_FLAG_INTERLACE)
+		val = SUN4I_TCON1_CTL_INTERLACE_ENABLE;
+	else
+		val = 0;
+	regmap_update_bits(tcon->regs, SUN4I_TCON1_CTL_REG,
+			   SUN4I_TCON1_CTL_INTERLACE_ENABLE,
+			   val);
+
+	/* Set the input resolution */
+	regmap_write(tcon->regs, SUN4I_TCON1_BASIC0_REG,
+		     SUN4I_TCON1_BASIC0_X(mode->crtc_hdisplay) |
+		     SUN4I_TCON1_BASIC0_Y(mode->crtc_vdisplay));
+
+	/* Set the upscaling resolution */
+	regmap_write(tcon->regs, SUN4I_TCON1_BASIC1_REG,
+		     SUN4I_TCON1_BASIC1_X(mode->crtc_hdisplay) |
+		     SUN4I_TCON1_BASIC1_Y(mode->crtc_vdisplay));
+
+	/* Set the output resolution */
+	regmap_write(tcon->regs, SUN4I_TCON1_BASIC2_REG,
+		     SUN4I_TCON1_BASIC2_X(mode->crtc_hdisplay) |
+		     SUN4I_TCON1_BASIC2_Y(mode->crtc_vdisplay));
+
+	/* Set horizontal display timings */
+	bp = mode->crtc_htotal - mode->crtc_hsync_end;
+	DRM_DEBUG_DRIVER("Setting horizontal total %d, backporch %d\n",
+			 mode->htotal, bp);
+	regmap_write(tcon->regs, SUN4I_TCON1_BASIC3_REG,
+		     SUN4I_TCON1_BASIC3_H_TOTAL(mode->crtc_htotal) |
+		     SUN4I_TCON1_BASIC3_H_BACKPORCH(bp));
+
+	/* Set vertical display timings */
+	bp = mode->crtc_vtotal - mode->crtc_vsync_end;
+	DRM_DEBUG_DRIVER("Setting vertical total %d, backporch %d\n",
+			 mode->vtotal, bp);
+	regmap_write(tcon->regs, SUN4I_TCON1_BASIC4_REG,
+		     SUN4I_TCON1_BASIC4_V_TOTAL(mode->vtotal) |
+		     SUN4I_TCON1_BASIC4_V_BACKPORCH(bp));
+
+	/* Set Hsync and Vsync length */
+	hsync = mode->crtc_hsync_end - mode->crtc_hsync_start;
+	vsync = mode->crtc_vsync_end - mode->crtc_vsync_start;
+	DRM_DEBUG_DRIVER("Setting HSYNC %d, VSYNC %d\n", hsync, vsync);
+	regmap_write(tcon->regs, SUN4I_TCON1_BASIC5_REG,
+		     SUN4I_TCON1_BASIC5_V_SYNC(vsync) |
+		     SUN4I_TCON1_BASIC5_H_SYNC(hsync));
+
+	/* Map output pins to channel 1 */
+	regmap_update_bits(tcon->regs, SUN4I_TCON_GCTL_REG,
+			   SUN4I_TCON_GCTL_IOMAP_MASK,
+			   SUN4I_TCON_GCTL_IOMAP_TCON1);
+
+	/*
+	 * FIXME: Undocumented bits
+	 */
+	if (tcon->has_mux)
+		regmap_write(tcon->regs, SUN4I_TCON_MUX_CTRL_REG, 1);
+}
+EXPORT_SYMBOL(sun4i_tcon1_mode_set);
+
+static void sun4i_tcon_finish_page_flip(struct drm_device *dev,
+					struct sun4i_crtc *scrtc)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&dev->event_lock, flags);
+	if (scrtc->event) {
+		drm_crtc_send_vblank_event(&scrtc->crtc, scrtc->event);
+		drm_crtc_vblank_put(&scrtc->crtc);
+		scrtc->event = NULL;
+	}
+	spin_unlock_irqrestore(&dev->event_lock, flags);
+}
+
+static irqreturn_t sun4i_tcon_handler(int irq, void *private)
+{
+	struct sun4i_tcon *tcon = private;
+	struct drm_device *drm = tcon->drm;
+	struct sun4i_drv *drv = drm->dev_private;
+	struct sun4i_crtc *scrtc = drv->crtc;
+	unsigned int status;
+
+	regmap_read(tcon->regs, SUN4I_TCON_GINT0_REG, &status);
+
+	if (!(status & (SUN4I_TCON_GINT0_VBLANK_INT(0) |
+			SUN4I_TCON_GINT0_VBLANK_INT(1))))
+		return IRQ_NONE;
+
+	drm_crtc_handle_vblank(&scrtc->crtc);
+	sun4i_tcon_finish_page_flip(drm, scrtc);
+
+	/* Acknowledge the interrupt */
+	regmap_update_bits(tcon->regs, SUN4I_TCON_GINT0_REG,
+			   SUN4I_TCON_GINT0_VBLANK_INT(0) |
+			   SUN4I_TCON_GINT0_VBLANK_INT(1),
+			   0);
+
+	return IRQ_HANDLED;
+}
+
+static int sun4i_tcon_init_clocks(struct device *dev,
+				  struct sun4i_tcon *tcon)
+{
+	tcon->clk = devm_clk_get(dev, "ahb");
+	if (IS_ERR(tcon->clk)) {
+		dev_err(dev, "Couldn't get the TCON bus clock\n");
+		return PTR_ERR(tcon->clk);
+	}
+	clk_prepare_enable(tcon->clk);
+
+	tcon->sclk0 = devm_clk_get(dev, "tcon-ch0");
+	if (IS_ERR(tcon->sclk0)) {
+		dev_err(dev, "Couldn't get the TCON channel 0 clock\n");
+		return PTR_ERR(tcon->sclk0);
+	}
+
+	tcon->sclk1 = devm_clk_get(dev, "tcon-ch1");
+	if (IS_ERR(tcon->sclk1)) {
+		dev_err(dev, "Couldn't get the TCON channel 1 clock\n");
+		return PTR_ERR(tcon->sclk1);
+	}
+
+	return sun4i_dclk_create(dev, tcon);
+}
+
+static void sun4i_tcon_free_clocks(struct sun4i_tcon *tcon)
+{
+	sun4i_dclk_free(tcon);
+	clk_disable_unprepare(tcon->clk);
+}
+
+static int sun4i_tcon_init_irq(struct device *dev,
+			       struct sun4i_tcon *tcon)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	int irq, ret;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "Couldn't retrieve the TCON interrupt\n");
+		return irq;
+	}
+
+	ret = devm_request_irq(dev, irq, sun4i_tcon_handler, 0,
+			       dev_name(dev), tcon);
+	if (ret) {
+		dev_err(dev, "Couldn't request the IRQ\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static struct regmap_config sun4i_tcon_regmap_config = {
+	.reg_bits	= 32,
+	.val_bits	= 32,
+	.reg_stride	= 4,
+	.max_register	= 0x800,
+};
+
+static int sun4i_tcon_init_regmap(struct device *dev,
+				  struct sun4i_tcon *tcon)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct resource *res;
+	void __iomem *regs;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(regs)) {
+		dev_err(dev, "Couldn't map the TCON registers\n");
+		return PTR_ERR(regs);
+	}
+
+	tcon->regs = devm_regmap_init_mmio(dev, regs,
+					   &sun4i_tcon_regmap_config);
+	if (IS_ERR(tcon->regs)) {
+		dev_err(dev, "Couldn't create the TCON regmap\n");
+		return PTR_ERR(tcon->regs);
+	}
+
+	/* Make sure the TCON is disabled and all IRQs are off */
+	regmap_write(tcon->regs, SUN4I_TCON_GCTL_REG, 0);
+	regmap_write(tcon->regs, SUN4I_TCON_GINT0_REG, 0);
+	regmap_write(tcon->regs, SUN4I_TCON_GINT1_REG, 0);
+
+	/* Disable IO lines and set them to tristate */
+	regmap_write(tcon->regs, SUN4I_TCON0_IO_TRI_REG, ~0);
+	regmap_write(tcon->regs, SUN4I_TCON1_IO_TRI_REG, ~0);
+
+	return 0;
+}
+
+static int sun4i_tcon_bind(struct device *dev, struct device *master,
+			   void *data)
+{
+	struct drm_device *drm = data;
+	struct sun4i_drv *drv = drm->dev_private;
+	struct sun4i_tcon *tcon;
+	int ret;
+
+	tcon = devm_kzalloc(dev, sizeof(*tcon), GFP_KERNEL);
+	if (!tcon)
+		return -ENOMEM;
+	dev_set_drvdata(dev, tcon);
+	drv->tcon = tcon;
+	tcon->drm = drm;
+
+	if (of_device_is_compatible(dev->of_node, "allwinner,sun5i-a13-tcon"))
+		tcon->has_mux = true;
+
+	tcon->lcd_rst = devm_reset_control_get(dev, "lcd");
+	if (IS_ERR(tcon->lcd_rst)) {
+		dev_err(dev, "Couldn't get our reset line\n");
+		return PTR_ERR(tcon->lcd_rst);
+	}
+
+	/* Make sure our TCON is reset */
+	if (!reset_control_status(tcon->lcd_rst))
+		reset_control_assert(tcon->lcd_rst);
+
+	ret = reset_control_deassert(tcon->lcd_rst);
+	if (ret) {
+		dev_err(dev, "Couldn't deassert our reset line\n");
+		return ret;
+	}
+
+	ret = sun4i_tcon_init_regmap(dev, tcon);
+	if (ret) {
+		dev_err(dev, "Couldn't init our TCON regmap\n");
+		goto err_assert_reset;
+	}
+
+	ret = sun4i_tcon_init_clocks(dev, tcon);
+	if (ret) {
+		dev_err(dev, "Couldn't init our TCON clocks\n");
+		goto err_assert_reset;
+	}
+
+	ret = sun4i_tcon_init_irq(dev, tcon);
+	if (ret) {
+		dev_err(dev, "Couldn't init our TCON interrupts\n");
+		goto err_free_clocks;
+	}
+
+	return 0;
+
+err_free_clocks:
+	sun4i_tcon_free_clocks(tcon);
+err_assert_reset:
+	reset_control_assert(tcon->lcd_rst);
+	return ret;
+}
+
+static void sun4i_tcon_unbind(struct device *dev, struct device *master,
+			      void *data)
+{
+	struct sun4i_tcon *tcon = dev_get_drvdata(dev);
+
+	sun4i_tcon_free_clocks(tcon);
+}
+
+static struct component_ops sun4i_tcon_ops = {
+	.bind	= sun4i_tcon_bind,
+	.unbind	= sun4i_tcon_unbind,
+};
+
+static int sun4i_tcon_probe(struct platform_device *pdev)
+{
+	return component_add(&pdev->dev, &sun4i_tcon_ops);
+}
+
+static int sun4i_tcon_remove(struct platform_device *pdev)
+{
+	component_del(&pdev->dev, &sun4i_tcon_ops);
+
+	return 0;
+}
+
+static const struct of_device_id sun4i_tcon_of_table[] = {
+	{ .compatible = "allwinner,sun5i-a13-tcon" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, sun4i_tcon_of_table);
+
+static struct platform_driver sun4i_tcon_platform_driver = {
+	.probe		= sun4i_tcon_probe,
+	.remove		= sun4i_tcon_remove,
+	.driver		= {
+		.name		= "sun4i-tcon",
+		.of_match_table	= sun4i_tcon_of_table,
+	},
+};
+module_platform_driver(sun4i_tcon_platform_driver);
+
+MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>");
+MODULE_DESCRIPTION("Allwinner A10 Timing Controller Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.h b/drivers/gpu/drm/sun4i/sun4i_tcon.h
new file mode 100644
index 000000000000..35161218c2c1
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.h
@@ -0,0 +1,184 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Boris Brezillon <boris.brezillon@free-electrons.com>
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef __SUN4I_TCON_H__
+#define __SUN4I_TCON_H__
+
+#include <drm/drm_crtc.h>
+
+#include <linux/kernel.h>
+#include <linux/reset.h>
+
+#define SUN4I_TCON_GCTL_REG			0x0
+#define SUN4I_TCON_GCTL_TCON_ENABLE			BIT(31)
+#define SUN4I_TCON_GCTL_IOMAP_MASK			BIT(0)
+#define SUN4I_TCON_GCTL_IOMAP_TCON1			(1 << 0)
+#define SUN4I_TCON_GCTL_IOMAP_TCON0			(0 << 0)
+
+#define SUN4I_TCON_GINT0_REG			0x4
+#define SUN4I_TCON_GINT0_VBLANK_ENABLE(pipe)		BIT(31 - (pipe))
+#define SUN4I_TCON_GINT0_VBLANK_INT(pipe)		BIT(15 - (pipe))
+
+#define SUN4I_TCON_GINT1_REG			0x8
+#define SUN4I_TCON_FRM_CTL_REG			0x10
+
+#define SUN4I_TCON0_CTL_REG			0x40
+#define SUN4I_TCON0_CTL_TCON_ENABLE			BIT(31)
+#define SUN4I_TCON0_CTL_CLK_DELAY_MASK			GENMASK(8, 4)
+#define SUN4I_TCON0_CTL_CLK_DELAY(delay)		((delay << 4) & SUN4I_TCON0_CTL_CLK_DELAY_MASK)
+
+#define SUN4I_TCON0_DCLK_REG			0x44
+#define SUN4I_TCON0_DCLK_GATE_BIT			(31)
+#define SUN4I_TCON0_DCLK_DIV_SHIFT			(0)
+#define SUN4I_TCON0_DCLK_DIV_WIDTH			(7)
+
+#define SUN4I_TCON0_BASIC0_REG			0x48
+#define SUN4I_TCON0_BASIC0_X(width)			((((width) - 1) & 0xfff) << 16)
+#define SUN4I_TCON0_BASIC0_Y(height)			(((height) - 1) & 0xfff)
+
+#define SUN4I_TCON0_BASIC1_REG			0x4c
+#define SUN4I_TCON0_BASIC1_H_TOTAL(total)		((((total) - 1) & 0x1fff) << 16)
+#define SUN4I_TCON0_BASIC1_H_BACKPORCH(bp)		(((bp) - 1) & 0xfff)
+
+#define SUN4I_TCON0_BASIC2_REG			0x50
+#define SUN4I_TCON0_BASIC2_V_TOTAL(total)		((((total) * 2) & 0x1fff) << 16)
+#define SUN4I_TCON0_BASIC2_V_BACKPORCH(bp)		(((bp) - 1) & 0xfff)
+
+#define SUN4I_TCON0_BASIC3_REG			0x54
+#define SUN4I_TCON0_BASIC3_H_SYNC(width)		((((width) - 1) & 0x7ff) << 16)
+#define SUN4I_TCON0_BASIC3_V_SYNC(height)		(((height) - 1) & 0x7ff)
+
+#define SUN4I_TCON0_HV_IF_REG			0x58
+#define SUN4I_TCON0_CPU_IF_REG			0x60
+#define SUN4I_TCON0_CPU_WR_REG			0x64
+#define SUN4I_TCON0_CPU_RD0_REG			0x68
+#define SUN4I_TCON0_CPU_RDA_REG			0x6c
+#define SUN4I_TCON0_TTL0_REG			0x70
+#define SUN4I_TCON0_TTL1_REG			0x74
+#define SUN4I_TCON0_TTL2_REG			0x78
+#define SUN4I_TCON0_TTL3_REG			0x7c
+#define SUN4I_TCON0_TTL4_REG			0x80
+#define SUN4I_TCON0_LVDS_IF_REG			0x84
+#define SUN4I_TCON0_IO_POL_REG			0x88
+#define SUN4I_TCON0_IO_POL_DCLK_PHASE(phase)		((phase & 3) << 28)
+#define SUN4I_TCON0_IO_POL_HSYNC_POSITIVE		BIT(25)
+#define SUN4I_TCON0_IO_POL_VSYNC_POSITIVE		BIT(24)
+
+#define SUN4I_TCON0_IO_TRI_REG			0x8c
+#define SUN4I_TCON0_IO_TRI_HSYNC_DISABLE		BIT(25)
+#define SUN4I_TCON0_IO_TRI_VSYNC_DISABLE		BIT(24)
+#define SUN4I_TCON0_IO_TRI_DATA_PINS_DISABLE(pins)	GENMASK(pins, 0)
+
+#define SUN4I_TCON1_CTL_REG			0x90
+#define SUN4I_TCON1_CTL_TCON_ENABLE			BIT(31)
+#define SUN4I_TCON1_CTL_INTERLACE_ENABLE		BIT(20)
+#define SUN4I_TCON1_CTL_CLK_DELAY_MASK			GENMASK(8, 4)
+#define SUN4I_TCON1_CTL_CLK_DELAY(delay)		((delay << 4) & SUN4I_TCON1_CTL_CLK_DELAY_MASK)
+
+#define SUN4I_TCON1_BASIC0_REG			0x94
+#define SUN4I_TCON1_BASIC0_X(width)			((((width) - 1) & 0xfff) << 16)
+#define SUN4I_TCON1_BASIC0_Y(height)			(((height) - 1) & 0xfff)
+
+#define SUN4I_TCON1_BASIC1_REG			0x98
+#define SUN4I_TCON1_BASIC1_X(width)			((((width) - 1) & 0xfff) << 16)
+#define SUN4I_TCON1_BASIC1_Y(height)			(((height) - 1) & 0xfff)
+
+#define SUN4I_TCON1_BASIC2_REG			0x9c
+#define SUN4I_TCON1_BASIC2_X(width)			((((width) - 1) & 0xfff) << 16)
+#define SUN4I_TCON1_BASIC2_Y(height)			(((height) - 1) & 0xfff)
+
+#define SUN4I_TCON1_BASIC3_REG			0xa0
+#define SUN4I_TCON1_BASIC3_H_TOTAL(total)		((((total) - 1) & 0x1fff) << 16)
+#define SUN4I_TCON1_BASIC3_H_BACKPORCH(bp)		(((bp) - 1) & 0xfff)
+
+#define SUN4I_TCON1_BASIC4_REG			0xa4
+#define SUN4I_TCON1_BASIC4_V_TOTAL(total)		(((total) & 0x1fff) << 16)
+#define SUN4I_TCON1_BASIC4_V_BACKPORCH(bp)		(((bp) - 1) & 0xfff)
+
+#define SUN4I_TCON1_BASIC5_REG			0xa8
+#define SUN4I_TCON1_BASIC5_H_SYNC(width)		((((width) - 1) & 0x3ff) << 16)
+#define SUN4I_TCON1_BASIC5_V_SYNC(height)		(((height) - 1) & 0x3ff)
+
+#define SUN4I_TCON1_IO_POL_REG			0xf0
+#define SUN4I_TCON1_IO_TRI_REG			0xf4
+#define SUN4I_TCON_CEU_CTL_REG			0x100
+#define SUN4I_TCON_CEU_MUL_RR_REG		0x110
+#define SUN4I_TCON_CEU_MUL_RG_REG		0x114
+#define SUN4I_TCON_CEU_MUL_RB_REG		0x118
+#define SUN4I_TCON_CEU_ADD_RC_REG		0x11c
+#define SUN4I_TCON_CEU_MUL_GR_REG		0x120
+#define SUN4I_TCON_CEU_MUL_GG_REG		0x124
+#define SUN4I_TCON_CEU_MUL_GB_REG		0x128
+#define SUN4I_TCON_CEU_ADD_GC_REG		0x12c
+#define SUN4I_TCON_CEU_MUL_BR_REG		0x130
+#define SUN4I_TCON_CEU_MUL_BG_REG		0x134
+#define SUN4I_TCON_CEU_MUL_BB_REG		0x138
+#define SUN4I_TCON_CEU_ADD_BC_REG		0x13c
+#define SUN4I_TCON_CEU_RANGE_R_REG		0x140
+#define SUN4I_TCON_CEU_RANGE_G_REG		0x144
+#define SUN4I_TCON_CEU_RANGE_B_REG		0x148
+#define SUN4I_TCON_MUX_CTRL_REG			0x200
+#define SUN4I_TCON1_FILL_CTL_REG		0x300
+#define SUN4I_TCON1_FILL_BEG0_REG		0x304
+#define SUN4I_TCON1_FILL_END0_REG		0x308
+#define SUN4I_TCON1_FILL_DATA0_REG		0x30c
+#define SUN4I_TCON1_FILL_BEG1_REG		0x310
+#define SUN4I_TCON1_FILL_END1_REG		0x314
+#define SUN4I_TCON1_FILL_DATA1_REG		0x318
+#define SUN4I_TCON1_FILL_BEG2_REG		0x31c
+#define SUN4I_TCON1_FILL_END2_REG		0x320
+#define SUN4I_TCON1_FILL_DATA2_REG		0x324
+#define SUN4I_TCON1_GAMMA_TABLE_REG		0x400
+
+#define SUN4I_TCON_MAX_CHANNELS		2
+
+struct sun4i_tcon {
+	struct drm_device		*drm;
+	struct regmap			*regs;
+
+	/* Main bus clock */
+	struct clk			*clk;
+
+	/* Clocks for the TCON channels */
+	struct clk			*sclk0;
+	struct clk			*sclk1;
+
+	/* Pixel clock */
+	struct clk			*dclk;
+
+	/* Reset control */
+	struct reset_control		*lcd_rst;
+
+	/* Platform adjustments */
+	bool				has_mux;
+};
+
+/* Global Control */
+void sun4i_tcon_disable(struct sun4i_tcon *tcon);
+void sun4i_tcon_enable(struct sun4i_tcon *tcon);
+
+/* Channel Control */
+void sun4i_tcon_channel_disable(struct sun4i_tcon *tcon, int channel);
+void sun4i_tcon_channel_enable(struct sun4i_tcon *tcon, int channel);
+
+void sun4i_tcon_enable_vblank(struct sun4i_tcon *tcon, bool enable);
+
+/* Mode Related Controls */
+void sun4i_tcon_switch_interlace(struct sun4i_tcon *tcon,
+				 bool enable);
+void sun4i_tcon0_mode_set(struct sun4i_tcon *tcon,
+			  struct drm_display_mode *mode);
+void sun4i_tcon1_mode_set(struct sun4i_tcon *tcon,
+			  struct drm_display_mode *mode);
+
+#endif /* __SUN4I_TCON_H__ */
-- 
2.7.3

[PATCH v3 13/19] drm: sun4i: Add DT bindings documentation

[Maxime Ripard]

The display pipeline of the Allwinner A10 is involving several loosely
coupled components.

Add a documentation for the bindings.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 .../bindings/display/sunxi/sun4i-drm.txt           | 254 +++++++++++++++++++++
 1 file changed, 254 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt

diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
new file mode 100644
index 000000000000..378edb919eae
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
@@ -0,0 +1,254 @@
+Allwinner A10 Display Pipeline
+==============================
+
+The Allwinner A10 Display pipeline is composed of several components
+that are going to be documented below:
+
+TV Encoder
+----------
+
+The TV Encoder supports the composite and VGA output. It is one end of
+the pipeline.
+
+Required properties:
+ - compatible: value should be "allwinner,sun4i-a10-tv-encoder".
+ - reg: base address and size of memory-mapped region
+ - clocks: the clocks driving the TV encoder
+ - resets: phandle to the reset controller driving the encoder
+
+- ports: A ports node with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt. The
+  first port should be the input endpoint.
+
+TCON
+----
+
+The TCON acts as a timing controller for RGB, LVDS and TV interfaces.
+
+Required properties:
+ - compatible: value should be "allwinner,sun5i-a13-tcon".
+ - reg: base address and size of memory-mapped region
+ - interrupts: interrupt associated to this IP
+ - clocks: phandles to the clocks feeding the TCON. Three are needed:
+   - 'ahb': the interface clocks
+   - 'tcon-ch0': The clock driving the TCON channel 0
+   - 'tcon-ch1': The clock driving the TCON channel 1
+ - resets: phandles to the reset controllers driving the encoder
+   - "lcd": the reset line for the TCON channel 0
+
+ - clock-names: the clock names mentioned above
+ - reset-names: the reset names mentioned above
+ - clock-output-names: Name of the pixel clock created
+
+- ports: A ports node with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt. The
+  first port should be the input endpoint, the second one the output
+
+Endpoints optional property:
+  - allwinner,panel: boolean to indicate that the endpoint is a panel
+
+
+Display Engine Backend
+----------------------
+
+The display engine backend exposes layers and sprites to the
+system.
+
+Required properties:
+  - compatible: value must be one of:
+    * allwinner,sun5i-a13-display-backend
+  - reg: base address and size of the memory-mapped region.
+  - clocks: phandles to the clocks feeding the frontend and backend
+    * ahb: the backend interface clock
+    * mod: the backend module clock
+    * ram: the backend DRAM clock
+  - clock-names: the clock names mentioned above
+  - resets: phandles to the reset controllers driving the backend
+
+- ports: A ports node with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt. The
+  first port should be the input endpoints, the second one the output
+
+Display Engine Frontend
+-----------------------
+
+The display engine frontend does formats conversion, scaling,
+deinterlacing and color space conversion.
+
+Required properties:
+  - compatible: value must be one of:
+    * allwinner,sun5i-a13-display-frontend
+  - reg: base address and size of the memory-mapped region.
+  - interrupts: interrupt associated to this IP
+  - clocks: phandles to the clocks feeding the frontend and backend
+    * ahb: the backend interface clock
+    * mod: the backend module clock
+    * ram: the backend DRAM clock
+  - clock-names: the clock names mentioned above
+  - resets: phandles to the reset controllers driving the backend
+
+Display Engine Pipeline
+-----------------------
+
+The display engine pipeline (and its entry point, since it can be
+either directly the backend or the frontend) is represented as an
+extra node.
+
+Required properties:
+  - compatible: value must be one of:
+    * allwinner,sun5i-a13-display-engine
+  - allwinner,pipelines: list of phandle to the entry points of the
+    pipelines (either to the frontend or backend)
+
+Example:
+
+panel: panel {
+	compatible = "olimex,lcd-olinuxino-43-ts";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		panel_input: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&tcon0_out_panel>;
+		};
+	};
+};
+
+tve0: tv-encoder@01c0a000 {
+	compatible = "allwinner,sun4i-a10-tv-encoder";
+	reg = <0x01c0a000 0x1000>;
+	clocks = <&ahb_gates 34>;
+	resets = <&tcon_ch0_clk 0>;
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		tve0_in_tcon0: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&tcon0_out_tve0>;
+		};
+	};
+};
+
+tcon0: lcd-controller@01c0c000 {
+	compatible = "allwinner,sun5i-a13-tcon";
+	reg = <0x01c0c000 0x1000>;
+	interrupts = <44>;
+	resets = <&tcon_ch0_clk 1>;
+	reset-names = "lcd";
+	clocks = <&ahb_gates 36>,
+		 <&tcon_ch0_clk>,
+		 <&tcon_ch1_clk>;
+	clock-names = "ahb",
+		      "tcon-ch0",
+		      "tcon-ch1";
+	clock-output-names = "tcon-pixel-clock";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		tcon0_in: port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			tcon0_in_be0: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&be0_out_tcon0>;
+			};
+		};
+
+		tcon0_out: port@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			tcon0_out_tve0: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&tve0_in_tcon0>;
+			};
+
+			tcon0_out_panel: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&panel_input>;
+				allwinner,panel;
+			};
+		};
+	};
+};
+
+fe0: display-frontend@01e00000 {
+	compatible = "allwinner,sun5i-a13-display-frontend";
+	reg = <0x01e00000 0x20000>;
+	interrupts = <47>;
+	clocks = <&ahb_gates 46>, <&de_fe_clk>,
+		 <&dram_gates 25>;
+	clock-names = "ahb", "mod",
+		      "ram";
+	resets = <&de_fe_clk>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fe0_out: port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			fe0_out_be0: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&be0_in_fe0>;
+			};
+		};
+	};
+};
+
+be0: display-backend@01e60000 {
+	compatible = "allwinner,sun5i-a13-display-backend";
+	reg = <0x01e60000 0x10000>;
+	clocks = <&ahb_gates 44>, <&de_be_clk>,
+		 <&dram_gates 26>;
+	clock-names = "ahb", "mod",
+		      "ram";
+	resets = <&de_be_clk>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		be0_in: port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			be0_in_fe0: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&fe0_out_be0>;
+			};
+		};
+
+		be0_out: port@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			be0_out_tcon0: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&tcon0_in_be0>;
+			};
+		};
+	};
+};
+
+display-engine {
+	compatible = "allwinner,sun5i-a13-display-engine";
+	pipelines = <&be0>;
+};
-- 
2.7.3

[PATCH v3 14/19] drm: sun4i: Add RGB output

[Maxime Ripard]

One of the A10 display pipeline possible output is an RGB interface to
drive LCD panels directly. This is done through the first channel of the
TCON that will output our video signals directly.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 drivers/gpu/drm/sun4i/Makefile     |   1 +
 drivers/gpu/drm/sun4i/sun4i_drv.c  |   7 ++
 drivers/gpu/drm/sun4i/sun4i_rgb.c  | 234 +++++++++++++++++++++++++++++++++++++
 drivers/gpu/drm/sun4i/sun4i_rgb.h  |  18 +++
 drivers/gpu/drm/sun4i/sun4i_tcon.c |  48 +++++++-
 drivers/gpu/drm/sun4i/sun4i_tcon.h |   2 +
 6 files changed, 309 insertions(+), 1 deletion(-)
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_rgb.c
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_rgb.h

diff --git a/drivers/gpu/drm/sun4i/Makefile b/drivers/gpu/drm/sun4i/Makefile
index 6df3ef32732d..830abb9b2b74 100644
--- a/drivers/gpu/drm/sun4i/Makefile
+++ b/drivers/gpu/drm/sun4i/Makefile
@@ -2,6 +2,7 @@ sun4i-drm-y += sun4i_crtc.o
 sun4i-drm-y += sun4i_drv.o
 sun4i-drm-y += sun4i_framebuffer.o
 sun4i-drm-y += sun4i_layer.o
+sun4i-drm-y += sun4i_rgb.o
 
 sun4i-tcon-y += sun4i_tcon.o
 sun4i-tcon-y += sun4i_dotclock.o
diff --git a/drivers/gpu/drm/sun4i/sun4i_drv.c b/drivers/gpu/drm/sun4i/sun4i_drv.c
index 5c64d2105dc7..5ba66ca5258b 100644
--- a/drivers/gpu/drm/sun4i/sun4i_drv.c
+++ b/drivers/gpu/drm/sun4i/sun4i_drv.c
@@ -244,6 +244,13 @@ static int sun4i_drv_add_endpoints(struct device *dev,
 	}
 
 	for_each_available_child_of_node(port, ep) {
+		/*
+		 * If the node is a panel, don't register it into the
+		 * component framework
+		 */
+		if (of_property_read_bool(ep, "allwinner,panel"))
+			continue;
+
 		remote = of_graph_get_remote_port_parent(ep);
 		if (!remote) {
 			DRM_DEBUG_DRIVER("Error retrieving the output node\n");
diff --git a/drivers/gpu/drm/sun4i/sun4i_rgb.c b/drivers/gpu/drm/sun4i/sun4i_rgb.c
new file mode 100644
index 000000000000..dd0dcc6cdc26
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_rgb.c
@@ -0,0 +1,234 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_panel.h>
+
+#include "sun4i_drv.h"
+#include "sun4i_tcon.h"
+
+struct sun4i_rgb {
+	struct drm_connector	connector;
+	struct drm_encoder	encoder;
+
+	struct sun4i_drv	*drv;
+};
+
+static inline struct sun4i_rgb *
+drm_connector_to_sun4i_rgb(struct drm_connector *connector)
+{
+	return container_of(connector, struct sun4i_rgb,
+			    connector);
+}
+
+static inline struct sun4i_rgb *
+drm_encoder_to_sun4i_rgb(struct drm_encoder *encoder)
+{
+	return container_of(encoder, struct sun4i_rgb,
+			    encoder);
+}
+
+static int sun4i_rgb_get_modes(struct drm_connector *connector)
+{
+	struct sun4i_rgb *rgb =
+		drm_connector_to_sun4i_rgb(connector);
+	struct sun4i_drv *drv = rgb->drv;
+	struct sun4i_tcon *tcon = drv->tcon;
+
+	return drm_panel_get_modes(tcon->panel);
+}
+
+static int sun4i_rgb_mode_valid(struct drm_connector *connector,
+				struct drm_display_mode *mode)
+{
+	u32 hsync = mode->hsync_end - mode->hsync_start;
+	u32 vsync = mode->vsync_end - mode->vsync_start;
+
+	DRM_DEBUG_DRIVER("Validating modes...\n");
+
+	if ((hsync < 1) || (hsync > 0x3ff) ||
+	    (mode->htotal < 1) || (mode->htotal > 0xfff))
+		return MODE_H_ILLEGAL;
+
+	DRM_DEBUG_DRIVER("Horizontal parameters OK\n");
+
+	if ((vsync < 1) || (vsync > 0x3ff) ||
+	    (mode->vtotal < 1) || (mode->vtotal > 0xfff))
+		return MODE_V_ILLEGAL;
+
+	DRM_DEBUG_DRIVER("Vertical parameters OK\n");
+
+	return MODE_OK;
+}
+
+static struct drm_encoder *
+sun4i_rgb_best_encoder(struct drm_connector *connector)
+{
+	struct sun4i_rgb *rgb =
+		drm_connector_to_sun4i_rgb(connector);
+
+	return &rgb->encoder;
+}
+
+static struct drm_connector_helper_funcs sun4i_rgb_con_helper_funcs = {
+	.get_modes	= sun4i_rgb_get_modes,
+	.mode_valid	= sun4i_rgb_mode_valid,
+	.best_encoder	= sun4i_rgb_best_encoder,
+};
+
+static enum drm_connector_status
+sun4i_rgb_connector_detect(struct drm_connector *connector, bool force)
+{
+	return connector_status_connected;
+}
+
+static void
+sun4i_rgb_connector_destroy(struct drm_connector *connector)
+{
+	struct sun4i_rgb *rgb = drm_connector_to_sun4i_rgb(connector);
+	struct sun4i_drv *drv = rgb->drv;
+	struct sun4i_tcon *tcon = drv->tcon;
+
+	drm_panel_detach(tcon->panel);
+	drm_connector_cleanup(connector);
+}
+
+static struct drm_connector_funcs sun4i_rgb_con_funcs = {
+	.dpms			= drm_atomic_helper_connector_dpms,
+	.detect			= sun4i_rgb_connector_detect,
+	.fill_modes		= drm_helper_probe_single_connector_modes,
+	.destroy		= sun4i_rgb_connector_destroy,
+	.reset			= drm_atomic_helper_connector_reset,
+	.atomic_duplicate_state	= drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state	= drm_atomic_helper_connector_destroy_state,
+};
+
+static int sun4i_rgb_atomic_check(struct drm_encoder *encoder,
+				  struct drm_crtc_state *crtc_state,
+				  struct drm_connector_state *conn_state)
+{
+	return 0;
+}
+
+static void sun4i_rgb_encoder_enable(struct drm_encoder *encoder)
+{
+	struct sun4i_rgb *rgb = drm_encoder_to_sun4i_rgb(encoder);
+	struct sun4i_drv *drv = rgb->drv;
+	struct sun4i_tcon *tcon = drv->tcon;
+
+	DRM_DEBUG_DRIVER("Enabling RGB output\n");
+
+	drm_panel_enable(tcon->panel);
+	sun4i_tcon_channel_enable(tcon, 0);
+}
+
+static void sun4i_rgb_encoder_disable(struct drm_encoder *encoder)
+{
+	struct sun4i_rgb *rgb = drm_encoder_to_sun4i_rgb(encoder);
+	struct sun4i_drv *drv = rgb->drv;
+	struct sun4i_tcon *tcon = drv->tcon;
+
+	DRM_DEBUG_DRIVER("Disabling RGB output\n");
+
+	sun4i_tcon_channel_disable(tcon, 0);
+	drm_panel_disable(tcon->panel);
+}
+
+static void sun4i_rgb_encoder_mode_set(struct drm_encoder *encoder,
+				       struct drm_display_mode *mode,
+				       struct drm_display_mode *adjusted_mode)
+{
+	struct sun4i_rgb *rgb = drm_encoder_to_sun4i_rgb(encoder);
+	struct sun4i_drv *drv = rgb->drv;
+	struct sun4i_tcon *tcon = drv->tcon;
+
+	sun4i_tcon0_mode_set(tcon, mode);
+
+	clk_set_rate(tcon->dclk, mode->crtc_clock * 1000);
+
+	/* FIXME: This seems to be board specific */
+	clk_set_phase(tcon->dclk, 120);
+}
+
+static struct drm_encoder_helper_funcs sun4i_rgb_enc_helper_funcs = {
+	.atomic_check	= sun4i_rgb_atomic_check,
+	.mode_set	= sun4i_rgb_encoder_mode_set,
+	.disable	= sun4i_rgb_encoder_disable,
+	.enable		= sun4i_rgb_encoder_enable,
+};
+
+static void sun4i_rgb_enc_destroy(struct drm_encoder *encoder)
+{
+	drm_encoder_cleanup(encoder);
+}
+
+static struct drm_encoder_funcs sun4i_rgb_enc_funcs = {
+	.destroy	= sun4i_rgb_enc_destroy,
+};
+
+int sun4i_rgb_init(struct drm_device *drm)
+{
+	struct sun4i_drv *drv = drm->dev_private;
+	struct sun4i_tcon *tcon = drv->tcon;
+	struct sun4i_rgb *rgb;
+	int ret;
+
+	/* If we don't have a panel, there's no point in going on */
+	if (!tcon->panel)
+		return -ENODEV;
+
+	rgb = devm_kzalloc(drm->dev, sizeof(*rgb), GFP_KERNEL);
+	if (!rgb)
+		return -ENOMEM;
+	rgb->drv = drv;
+
+	drm_encoder_helper_add(&rgb->encoder,
+			       &sun4i_rgb_enc_helper_funcs);
+	ret = drm_encoder_init(drm,
+			       &rgb->encoder,
+			       &sun4i_rgb_enc_funcs,
+			       DRM_MODE_ENCODER_NONE,
+			       NULL);
+	if (ret) {
+		dev_err(drm->dev, "Couldn't initialise the rgb encoder\n");
+		goto err_out;
+	}
+
+	/* The RGB encoder can only work with the TCON channel 0 */
+	rgb->encoder.possible_crtcs = BIT(0);
+
+	drm_connector_helper_add(&rgb->connector,
+				 &sun4i_rgb_con_helper_funcs);
+	ret = drm_connector_init(drm, &rgb->connector,
+				 &sun4i_rgb_con_funcs,
+				 DRM_MODE_CONNECTOR_Unknown);
+	if (ret) {
+		dev_err(drm->dev, "Couldn't initialise the rgb connector\n");
+		goto err_cleanup_connector;
+	}
+
+	drm_mode_connector_attach_encoder(&rgb->connector, &rgb->encoder);
+
+	drm_panel_attach(tcon->panel, &rgb->connector);
+
+	return 0;
+
+err_cleanup_connector:
+	drm_encoder_cleanup(&rgb->encoder);
+err_out:
+	return ret;
+}
+EXPORT_SYMBOL(sun4i_rgb_init);
diff --git a/drivers/gpu/drm/sun4i/sun4i_rgb.h b/drivers/gpu/drm/sun4i/sun4i_rgb.h
new file mode 100644
index 000000000000..7c4da4c8acdd
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_rgb.h
@@ -0,0 +1,18 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef _SUN4I_RGB_H_
+#define _SUN4I_RGB_H_
+
+int sun4i_rgb_init(struct drm_device *drm);
+
+#endif /* _SUN4I_RGB_H_ */
diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c b/drivers/gpu/drm/sun4i/sun4i_tcon.c
index b6e57ed79df4..8ae0b20055ee 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tcon.c
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
@@ -15,10 +15,12 @@
 #include <drm/drm_crtc.h>
 #include <drm/drm_crtc_helper.h>
 #include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
 
 #include <linux/component.h>
 #include <linux/ioport.h>
 #include <linux/of_address.h>
+#include <linux/of_graph.h>
 #include <linux/of_irq.h>
 #include <linux/regmap.h>
 #include <linux/reset.h>
@@ -26,6 +28,7 @@
 #include "sun4i_crtc.h"
 #include "sun4i_dotclock.h"
 #include "sun4i_drv.h"
+#include "sun4i_rgb.h"
 #include "sun4i_tcon.h"
 
 void sun4i_tcon_disable(struct sun4i_tcon *tcon)
@@ -385,12 +388,29 @@ static int sun4i_tcon_init_regmap(struct device *dev,
 	return 0;
 }
 
+static struct device_node *sun4i_tcon_find_panel(struct device_node *node)
+{
+	struct device_node *port, *end_node;
+
+	/* Inputs are listed first, then outputs */
+	port = of_graph_get_port_by_id(node, 1);
+
+	/* Iterate over the endpoints to find a panel */
+	for_each_child_of_node(port, end_node)
+		/* If the endpoint is not a panel, go on */
+		if (of_property_read_bool(end_node, "allwinner,panel"))
+			return of_graph_get_remote_port_parent(end_node);
+
+	return NULL;
+}
+
 static int sun4i_tcon_bind(struct device *dev, struct device *master,
 			   void *data)
 {
 	struct drm_device *drm = data;
 	struct sun4i_drv *drv = drm->dev_private;
 	struct sun4i_tcon *tcon;
+	struct device_node *np;
 	int ret;
 
 	tcon = devm_kzalloc(dev, sizeof(*tcon), GFP_KERNEL);
@@ -437,7 +457,20 @@ static int sun4i_tcon_bind(struct device *dev, struct device *master,
 		goto err_free_clocks;
 	}
 
-	return 0;
+	np = sun4i_tcon_find_panel(dev->of_node);
+	if (!np) {
+		dev_info(dev, "No panel found... RGB output disabled\n");
+		return 0;
+	}
+
+	tcon->panel = of_drm_find_panel(np);
+	if (!tcon->panel) {
+		dev_err(dev, "Couldn't find our panel\n");
+		ret = -ENODEV;
+		goto err_free_clocks;
+	}
+
+	return sun4i_rgb_init(drm);
 
 err_free_clocks:
 	sun4i_tcon_free_clocks(tcon);
@@ -461,6 +494,19 @@ static struct component_ops sun4i_tcon_ops = {
 
 static int sun4i_tcon_probe(struct platform_device *pdev)
 {
+	struct device_node *node = pdev->dev.of_node;
+	struct device_node *panel_node;
+
+	panel_node = sun4i_tcon_find_panel(node);
+	if (panel_node) {
+		/*
+		 * If the panel is not ready yet, defer the probe
+		 * before registering into the component framework.
+		 */
+		if (!of_drm_find_panel(panel_node))
+			return -EPROBE_DEFER;
+	}
+
 	return component_add(&pdev->dev, &sun4i_tcon_ops);
 }
 
diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.h b/drivers/gpu/drm/sun4i/sun4i_tcon.h
index 35161218c2c1..0e0b11db401b 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tcon.h
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.h
@@ -161,6 +161,8 @@ struct sun4i_tcon {
 
 	/* Platform adjustments */
 	bool				has_mux;
+
+	struct drm_panel		*panel;
 };
 
 /* Global Control */
-- 
2.7.3

[PATCH v3 15/19] drm: sun4i: Add composite output

[Maxime Ripard]

Some Allwinner SoCs have an IP called the TV encoder that is used to output
composite and VGA signals. In such a case, we need to use the second TCON
channel.

Add support for that TV encoder.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 drivers/gpu/drm/sun4i/Makefile   |   2 +
 drivers/gpu/drm/sun4i/sun4i_tv.c | 621 +++++++++++++++++++++++++++++++++++++++
 2 files changed, 623 insertions(+)
 create mode 100644 drivers/gpu/drm/sun4i/sun4i_tv.c

diff --git a/drivers/gpu/drm/sun4i/Makefile b/drivers/gpu/drm/sun4i/Makefile
index 830abb9b2b74..c93498f6a795 100644
--- a/drivers/gpu/drm/sun4i/Makefile
+++ b/drivers/gpu/drm/sun4i/Makefile
@@ -9,3 +9,5 @@ sun4i-tcon-y += sun4i_dotclock.o
 
 obj-$(CONFIG_DRM_SUN4I)		+= sun4i-drm.o sun4i-tcon.o
 obj-$(CONFIG_DRM_SUN4I)		+= sun4i_backend.o
+
+obj-$(CONFIG_DRM_SUN4I)		+= sun4i_tv.o
diff --git a/drivers/gpu/drm/sun4i/sun4i_tv.c b/drivers/gpu/drm/sun4i/sun4i_tv.c
new file mode 100644
index 000000000000..78634dfc0f77
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun4i_tv.c
@@ -0,0 +1,621 @@
+/*
+ * Copyright (C) 2015 Free Electrons
+ * Copyright (C) 2015 NextThing Co
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/component.h>
+#include <linux/of_address.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_panel.h>
+
+#include "sun4i_backend.h"
+#include "sun4i_drv.h"
+#include "sun4i_tcon.h"
+
+#define SUN4I_TVE_EN_REG		0x000
+#define SUN4I_TVE_EN_DAC_MAP_MASK		GENMASK(19, 4)
+#define SUN4I_TVE_EN_DAC_MAP(dac, out)		(((out) & 0xf) << (dac + 1) * 4)
+#define SUN4I_TVE_EN_ENABLE			BIT(0)
+
+#define SUN4I_TVE_CFG0_REG		0x004
+#define SUN4I_TVE_CFG0_DAC_CONTROL_54M		BIT(26)
+#define SUN4I_TVE_CFG0_CORE_DATAPATH_54M	BIT(25)
+#define SUN4I_TVE_CFG0_CORE_CONTROL_54M		BIT(24)
+#define SUN4I_TVE_CFG0_YC_EN			BIT(17)
+#define SUN4I_TVE_CFG0_COMP_EN			BIT(16)
+#define SUN4I_TVE_CFG0_RES(x)			((x) & 0xf)
+#define SUN4I_TVE_CFG0_RES_480i			SUN4I_TVE_CFG0_RES(0)
+#define SUN4I_TVE_CFG0_RES_576i			SUN4I_TVE_CFG0_RES(1)
+
+#define SUN4I_TVE_DAC0_REG		0x008
+#define SUN4I_TVE_DAC0_CLOCK_INVERT		BIT(24)
+#define SUN4I_TVE_DAC0_LUMA(x)			(((x) & 3) << 20)
+#define SUN4I_TVE_DAC0_LUMA_0_4			SUN4I_TVE_DAC0_LUMA(3)
+#define SUN4I_TVE_DAC0_CHROMA(x)		(((x) & 3) << 18)
+#define SUN4I_TVE_DAC0_CHROMA_0_75		SUN4I_TVE_DAC0_CHROMA(3)
+#define SUN4I_TVE_DAC0_INTERNAL_DAC(x)		(((x) & 3) << 16)
+#define SUN4I_TVE_DAC0_INTERNAL_DAC_37_5_OHMS	SUN4I_TVE_DAC0_INTERNAL_DAC(3)
+#define SUN4I_TVE_DAC0_DAC_EN(dac)		BIT(dac)
+
+#define SUN4I_TVE_NOTCH_REG		0x00c
+#define SUN4I_TVE_NOTCH_DAC0_TO_DAC_DLY(dac, x)	((4 - (x)) << (dac * 3))
+
+#define SUN4I_TVE_CHROMA_FREQ_REG	0x010
+
+#define SUN4I_TVE_PORCH_REG		0x014
+#define SUN4I_TVE_PORCH_BACK(x)			((x) << 16)
+#define SUN4I_TVE_PORCH_FRONT(x)		(x)
+
+#define SUN4I_TVE_LINE_REG		0x01c
+#define SUN4I_TVE_LINE_FIRST(x)			((x) << 16)
+#define SUN4I_TVE_LINE_NUMBER(x)		(x)
+
+#define SUN4I_TVE_LEVEL_REG		0x020
+#define SUN4I_TVE_LEVEL_BLANK(x)		((x) << 16)
+#define SUN4I_TVE_LEVEL_BLACK(x)		(x)
+
+#define SUN4I_TVE_DAC1_REG		0x024
+#define SUN4I_TVE_DAC1_AMPLITUDE(dac, x)	((x) << (dac * 8))
+
+#define SUN4I_TVE_DETECT_STA_REG	0x038
+#define SUN4I_TVE_DETECT_STA_DAC(dac)		BIT((dac * 8))
+#define SUN4I_TVE_DETECT_STA_UNCONNECTED		0
+#define SUN4I_TVE_DETECT_STA_CONNECTED			1
+#define SUN4I_TVE_DETECT_STA_GROUND			2
+
+#define SUN4I_TVE_CB_CR_LVL_REG		0x10c
+#define SUN4I_TVE_CB_CR_LVL_CR_BURST(x)		((x) << 8)
+#define SUN4I_TVE_CB_CR_LVL_CB_BURST(x)		(x)
+
+#define SUN4I_TVE_TINT_BURST_PHASE_REG	0x110
+#define SUN4I_TVE_TINT_BURST_PHASE_CHROMA(x)	(x)
+
+#define SUN4I_TVE_BURST_WIDTH_REG	0x114
+#define SUN4I_TVE_BURST_WIDTH_BREEZEWAY(x)	((x) << 16)
+#define SUN4I_TVE_BURST_WIDTH_BURST_WIDTH(x)	((x) << 8)
+#define SUN4I_TVE_BURST_WIDTH_HSYNC_WIDTH(x)	(x)
+
+#define SUN4I_TVE_CB_CR_GAIN_REG	0x118
+#define SUN4I_TVE_CB_CR_GAIN_CR(x)		((x) << 8)
+#define SUN4I_TVE_CB_CR_GAIN_CB(x)		(x)
+
+#define SUN4I_TVE_SYNC_VBI_REG		0x11c
+#define SUN4I_TVE_SYNC_VBI_SYNC(x)		((x) << 16)
+#define SUN4I_TVE_SYNC_VBI_VBLANK(x)		(x)
+
+#define SUN4I_TVE_ACTIVE_LINE_REG	0x124
+#define SUN4I_TVE_ACTIVE_LINE(x)		(x)
+
+#define SUN4I_TVE_CHROMA_REG		0x128
+#define SUN4I_TVE_CHROMA_COMP_GAIN(x)		((x) & 3)
+#define SUN4I_TVE_CHROMA_COMP_GAIN_50		SUN4I_TVE_CHROMA_COMP_GAIN(2)
+
+#define SUN4I_TVE_12C_REG		0x12c
+#define SUN4I_TVE_12C_NOTCH_WIDTH_WIDE		BIT(8)
+#define SUN4I_TVE_12C_COMP_YUV_EN		BIT(0)
+
+#define SUN4I_TVE_RESYNC_REG		0x130
+#define SUN4I_TVE_RESYNC_FIELD			BIT(31)
+#define SUN4I_TVE_RESYNC_LINE(x)		((x) << 16)
+#define SUN4I_TVE_RESYNC_PIXEL(x)		(x)
+
+#define SUN4I_TVE_SLAVE_REG		0x134
+
+#define SUN4I_TVE_WSS_DATA2_REG		0x244
+
+struct color_gains {
+	u16	cb;
+	u16	cr;
+};
+
+struct burst_levels {
+	u16	cb;
+	u16	cr;
+};
+
+struct video_levels {
+	u16	black;
+	u16	blank;
+};
+
+struct resync_parameters {
+	bool	field;
+	u16	line;
+	u16	pixel;
+};
+
+struct tv_mode {
+	char		*name;
+
+	u32		mode;
+	u32		chroma_freq;
+	u16		back_porch;
+	u16		front_porch;
+	u16		line_number;
+	u16		vblank_level;
+
+	u32		hdisplay;
+	u16		hfront_porch;
+	u16		hsync_len;
+	u16		hback_porch;
+
+	u32		vdisplay;
+	u16		vfront_porch;
+	u16		vsync_len;
+	u16		vback_porch;
+
+	bool		yc_en;
+	bool		dac3_en;
+	bool		dac_bit25_en;
+
+	struct color_gains		*color_gains;
+	struct burst_levels		*burst_levels;
+	struct video_levels		*video_levels;
+	struct resync_parameters	*resync_params;
+};
+
+struct sun4i_tv {
+	struct drm_connector	connector;
+	struct drm_encoder	encoder;
+
+	struct clk		*clk;
+	struct regmap		*regs;
+	struct reset_control	*reset;
+
+	struct sun4i_drv	*drv;
+};
+
+struct tv_mode tv_modes[] = {
+};
+
+static inline struct sun4i_tv *
+drm_encoder_to_sun4i_tv(struct drm_encoder *encoder)
+{
+	return container_of(encoder, struct sun4i_tv,
+			    encoder);
+}
+
+static inline struct sun4i_tv *
+drm_connector_to_sun4i_tv(struct drm_connector *connector)
+{
+	return container_of(connector, struct sun4i_tv,
+			    connector);
+}
+
+/*
+ * FIXME: If only the drm_display_mode private field was usable, this
+ * could go away...
+ *
+ * So far, it doesn't seem to be preserved when the mode is passed by
+ * to mode_set for some reason.
+ */
+static struct tv_mode *sun4i_tv_find_tv_by_mode(struct drm_display_mode *mode)
+{
+	int i;
+
+	/* First try to identify the mode by name */
+	for (i = 0; i < ARRAY_SIZE(tv_modes); i++) {
+		struct tv_mode *tv_mode = &tv_modes[i];
+
+		DRM_DEBUG_DRIVER("Comparing mode %s vs %s",
+				 mode->name, tv_mode->name);
+
+		if (!strcmp(mode->name, tv_mode->name))
+			return tv_mode;
+	}
+
+	/* Then by number of lines */
+	for (i = 0; i < ARRAY_SIZE(tv_modes); i++) {
+		struct tv_mode *tv_mode = &tv_modes[i];
+
+		DRM_DEBUG_DRIVER("Comparing mode %s vs %s (X: %d vs %d)",
+				 mode->name, tv_mode->name,
+				 mode->vdisplay, tv_mode->vdisplay);
+
+		if (mode->vdisplay == tv_mode->vdisplay)
+			return tv_mode;
+	}
+
+	return NULL;
+}
+
+static void sun4i_tv_mode_to_drm_mode(struct tv_mode *tv_mode,
+				      struct drm_display_mode *mode)
+{
+	DRM_DEBUG_DRIVER("Creating mode %s\n", mode->name);
+
+	mode->type = DRM_MODE_TYPE_DRIVER;
+	mode->clock = 13500;
+	mode->flags = DRM_MODE_FLAG_INTERLACE;
+
+	mode->hdisplay = tv_mode->hdisplay;
+	mode->hsync_start = mode->hdisplay + tv_mode->hfront_porch;
+	mode->hsync_end = mode->hsync_start + tv_mode->hsync_len;
+	mode->htotal = mode->hsync_end  + tv_mode->hback_porch;
+
+	mode->vdisplay = tv_mode->vdisplay;
+	mode->vsync_start = mode->vdisplay + tv_mode->vfront_porch;
+	mode->vsync_end = mode->vsync_start + tv_mode->vsync_len;
+	mode->vtotal = mode->vsync_end  + tv_mode->vback_porch;
+}
+
+static int sun4i_tv_atomic_check(struct drm_encoder *encoder,
+				 struct drm_crtc_state *crtc_state,
+				 struct drm_connector_state *conn_state)
+{
+	return 0;
+}
+
+static void sun4i_tv_disable(struct drm_encoder *encoder)
+{
+	struct sun4i_tv *tv = drm_encoder_to_sun4i_tv(encoder);
+	struct sun4i_drv *drv = tv->drv;
+	struct sun4i_tcon *tcon = drv->tcon;
+
+	DRM_DEBUG_DRIVER("Disabling the TV Output\n");
+
+	sun4i_tcon_channel_disable(tcon, 1);
+
+	regmap_update_bits(tv->regs, SUN4I_TVE_EN_REG,
+			   SUN4I_TVE_EN_ENABLE,
+			   0);
+	sun4i_backend_disable_color_correction(drv->backend);
+}
+
+static void sun4i_tv_enable(struct drm_encoder *encoder)
+{
+	struct sun4i_tv *tv = drm_encoder_to_sun4i_tv(encoder);
+	struct sun4i_drv *drv = tv->drv;
+	struct sun4i_tcon *tcon = drv->tcon;
+
+	DRM_DEBUG_DRIVER("Enabling the TV Output\n");
+
+	sun4i_backend_apply_color_correction(drv->backend);
+
+	regmap_update_bits(tv->regs, SUN4I_TVE_EN_REG,
+			   SUN4I_TVE_EN_ENABLE,
+			   SUN4I_TVE_EN_ENABLE);
+
+	sun4i_tcon_channel_enable(tcon, 1);
+}
+
+static void sun4i_tv_mode_set(struct drm_encoder *encoder,
+			      struct drm_display_mode *mode,
+			      struct drm_display_mode *adjusted_mode)
+{
+	struct sun4i_tv *tv = drm_encoder_to_sun4i_tv(encoder);
+	struct sun4i_drv *drv = tv->drv;
+	struct sun4i_tcon *tcon = drv->tcon;
+	struct tv_mode *tv_mode = sun4i_tv_find_tv_by_mode(mode);
+
+	sun4i_tcon1_mode_set(tcon, mode);
+
+	/* Enable and map the DAC to the output */
+	regmap_update_bits(tv->regs, SUN4I_TVE_EN_REG,
+			   SUN4I_TVE_EN_DAC_MAP_MASK,
+			   SUN4I_TVE_EN_DAC_MAP(0, 1) |
+			   SUN4I_TVE_EN_DAC_MAP(1, 2) |
+			   SUN4I_TVE_EN_DAC_MAP(2, 3) |
+			   SUN4I_TVE_EN_DAC_MAP(3, 4));
+
+	/* Set PAL settings */
+	regmap_write(tv->regs, SUN4I_TVE_CFG0_REG,
+		     tv_mode->mode |
+		     (tv_mode->yc_en ? SUN4I_TVE_CFG0_YC_EN : 0) |
+		     SUN4I_TVE_CFG0_COMP_EN |
+		     SUN4I_TVE_CFG0_DAC_CONTROL_54M |
+		     SUN4I_TVE_CFG0_CORE_DATAPATH_54M |
+		     SUN4I_TVE_CFG0_CORE_CONTROL_54M);
+
+	/* Configure the DAC for a composite output */
+	regmap_write(tv->regs, SUN4I_TVE_DAC0_REG,
+		     SUN4I_TVE_DAC0_DAC_EN(0) |
+		     (tv_mode->dac3_en ? SUN4I_TVE_DAC0_DAC_EN(3) : 0) |
+		     SUN4I_TVE_DAC0_INTERNAL_DAC_37_5_OHMS |
+		     SUN4I_TVE_DAC0_CHROMA_0_75 |
+		     SUN4I_TVE_DAC0_LUMA_0_4 |
+		     SUN4I_TVE_DAC0_CLOCK_INVERT |
+		     (tv_mode->dac_bit25_en ? BIT(25) : 0) |
+		     BIT(30));
+
+	/* Configure the sample delay between DAC0 and the other DAC */
+	regmap_write(tv->regs, SUN4I_TVE_NOTCH_REG,
+		     SUN4I_TVE_NOTCH_DAC0_TO_DAC_DLY(1, 0) |
+		     SUN4I_TVE_NOTCH_DAC0_TO_DAC_DLY(2, 0));
+
+	regmap_write(tv->regs, SUN4I_TVE_CHROMA_FREQ_REG,
+		     tv_mode->chroma_freq);
+
+	/* Set the front and back porch */
+	regmap_write(tv->regs, SUN4I_TVE_PORCH_REG,
+		     SUN4I_TVE_PORCH_BACK(tv_mode->back_porch) |
+		     SUN4I_TVE_PORCH_FRONT(tv_mode->front_porch));
+
+	/* Set the lines setup */
+	regmap_write(tv->regs, SUN4I_TVE_LINE_REG,
+		     SUN4I_TVE_LINE_FIRST(22) |
+		     SUN4I_TVE_LINE_NUMBER(tv_mode->line_number));
+
+	regmap_write(tv->regs, SUN4I_TVE_LEVEL_REG,
+		     SUN4I_TVE_LEVEL_BLANK(tv_mode->video_levels->blank) |
+		     SUN4I_TVE_LEVEL_BLACK(tv_mode->video_levels->black));
+
+	regmap_write(tv->regs, SUN4I_TVE_DAC1_REG,
+		     SUN4I_TVE_DAC1_AMPLITUDE(0, 0x18) |
+		     SUN4I_TVE_DAC1_AMPLITUDE(1, 0x18) |
+		     SUN4I_TVE_DAC1_AMPLITUDE(2, 0x18) |
+		     SUN4I_TVE_DAC1_AMPLITUDE(3, 0x18));
+
+	regmap_write(tv->regs, SUN4I_TVE_CB_CR_LVL_REG,
+		     SUN4I_TVE_CB_CR_LVL_CB_BURST(tv_mode->burst_levels->cb) |
+		     SUN4I_TVE_CB_CR_LVL_CR_BURST(tv_mode->burst_levels->cr));
+
+	/* Set burst width for a composite output */
+	regmap_write(tv->regs, SUN4I_TVE_BURST_WIDTH_REG,
+		     SUN4I_TVE_BURST_WIDTH_HSYNC_WIDTH(126) |
+		     SUN4I_TVE_BURST_WIDTH_BURST_WIDTH(68) |
+		     SUN4I_TVE_BURST_WIDTH_BREEZEWAY(22));
+
+	regmap_write(tv->regs, SUN4I_TVE_CB_CR_GAIN_REG,
+		     SUN4I_TVE_CB_CR_GAIN_CB(tv_mode->color_gains->cb) |
+		     SUN4I_TVE_CB_CR_GAIN_CR(tv_mode->color_gains->cr));
+
+	regmap_write(tv->regs, SUN4I_TVE_SYNC_VBI_REG,
+		     SUN4I_TVE_SYNC_VBI_SYNC(0x10) |
+		     SUN4I_TVE_SYNC_VBI_VBLANK(tv_mode->vblank_level));
+
+	regmap_write(tv->regs, SUN4I_TVE_ACTIVE_LINE_REG,
+		     SUN4I_TVE_ACTIVE_LINE(1440));
+
+	/* Set composite chroma gain to 50 % */
+	regmap_write(tv->regs, SUN4I_TVE_CHROMA_REG,
+		     SUN4I_TVE_CHROMA_COMP_GAIN_50);
+
+	regmap_write(tv->regs, SUN4I_TVE_12C_REG,
+		     SUN4I_TVE_12C_COMP_YUV_EN |
+		     SUN4I_TVE_12C_NOTCH_WIDTH_WIDE);
+
+	regmap_write(tv->regs, SUN4I_TVE_RESYNC_REG,
+		     SUN4I_TVE_RESYNC_PIXEL(tv_mode->resync_params->pixel) |
+		     SUN4I_TVE_RESYNC_LINE(tv_mode->resync_params->line) |
+		     (tv_mode->resync_params->field ?
+		      SUN4I_TVE_RESYNC_FIELD : 0));
+
+	regmap_write(tv->regs, SUN4I_TVE_SLAVE_REG, 0);
+
+	clk_set_rate(tcon->sclk1, mode->crtc_clock * 1000);
+}
+
+static struct drm_encoder_helper_funcs sun4i_tv_helper_funcs = {
+	.atomic_check	= sun4i_tv_atomic_check,
+	.disable	= sun4i_tv_disable,
+	.enable		= sun4i_tv_enable,
+	.mode_set	= sun4i_tv_mode_set,
+};
+
+static void sun4i_tv_destroy(struct drm_encoder *encoder)
+{
+	drm_encoder_cleanup(encoder);
+}
+
+static struct drm_encoder_funcs sun4i_tv_funcs = {
+	.destroy	= sun4i_tv_destroy,
+};
+
+static int sun4i_tv_comp_get_modes(struct drm_connector *connector)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(tv_modes); i++) {
+		struct drm_display_mode *mode = drm_mode_create(connector->dev);
+		struct tv_mode *tv_mode = &tv_modes[i];
+
+		strcpy(mode->name, tv_mode->name);
+
+		sun4i_tv_mode_to_drm_mode(tv_mode, mode);
+		drm_mode_probed_add(connector, mode);
+	}
+
+	return i;
+}
+
+static int sun4i_tv_comp_mode_valid(struct drm_connector *connector,
+				    struct drm_display_mode *mode)
+{
+	/* TODO */
+	return MODE_OK;
+}
+
+static struct drm_encoder *
+sun4i_tv_comp_best_encoder(struct drm_connector *connector)
+{
+	struct sun4i_tv *tv = drm_connector_to_sun4i_tv(connector);
+
+	return &tv->encoder;
+}
+
+static struct drm_connector_helper_funcs sun4i_tv_comp_connector_helper_funcs = {
+	.get_modes	= sun4i_tv_comp_get_modes,
+	.mode_valid	= sun4i_tv_comp_mode_valid,
+	.best_encoder	= sun4i_tv_comp_best_encoder,
+};
+
+static enum drm_connector_status
+sun4i_tv_comp_connector_detect(struct drm_connector *connector, bool force)
+{
+	return connector_status_connected;
+}
+
+static void
+sun4i_tv_comp_connector_destroy(struct drm_connector *connector)
+{
+	drm_connector_cleanup(connector);
+}
+
+static struct drm_connector_funcs sun4i_tv_comp_connector_funcs = {
+	.dpms			= drm_atomic_helper_connector_dpms,
+	.detect			= sun4i_tv_comp_connector_detect,
+	.fill_modes		= drm_helper_probe_single_connector_modes,
+	.destroy		= sun4i_tv_comp_connector_destroy,
+	.reset			= drm_atomic_helper_connector_reset,
+	.atomic_duplicate_state	= drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state	= drm_atomic_helper_connector_destroy_state,
+};
+
+static struct regmap_config sun4i_tv_regmap_config = {
+	.reg_bits	= 32,
+	.val_bits	= 32,
+	.reg_stride	= 4,
+	.max_register	= SUN4I_TVE_WSS_DATA2_REG,
+	.name		= "tv-encoder",
+};
+
+static int sun4i_tv_bind(struct device *dev, struct device *master,
+			 void *data)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct drm_device *drm = data;
+	struct sun4i_drv *drv = drm->dev_private;
+	struct sun4i_tv *tv;
+	struct resource *res;
+	void __iomem *regs;
+	int ret;
+
+	tv = devm_kzalloc(dev, sizeof(*tv), GFP_KERNEL);
+	if (!tv)
+		return -ENOMEM;
+	tv->drv = drv;
+	dev_set_drvdata(dev, tv);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(regs)) {
+		dev_err(dev, "Couldn't map the TV encoder registers\n");
+		return PTR_ERR(regs);
+	}
+
+	tv->regs = devm_regmap_init_mmio(dev, regs,
+					 &sun4i_tv_regmap_config);
+	if (IS_ERR(tv->regs)) {
+		dev_err(dev, "Couldn't create the TV encoder regmap\n");
+		return PTR_ERR(tv->regs);
+	}
+
+	tv->reset = devm_reset_control_get(dev, NULL);
+	if (IS_ERR(tv->reset)) {
+		dev_err(dev, "Couldn't get our reset line\n");
+		return PTR_ERR(tv->reset);
+	}
+
+	ret = reset_control_deassert(tv->reset);
+	if (ret) {
+		dev_err(dev, "Couldn't deassert our reset line\n");
+		return ret;
+	}
+
+	tv->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(tv->clk)) {
+		dev_err(dev, "Couldn't get the TV encoder clock\n");
+		ret = PTR_ERR(tv->clk);
+		goto err_assert_reset;
+	}
+	clk_prepare_enable(tv->clk);
+
+	drm_encoder_helper_add(&tv->encoder,
+			       &sun4i_tv_helper_funcs);
+	ret = drm_encoder_init(drm,
+			       &tv->encoder,
+			       &sun4i_tv_funcs,
+			       DRM_MODE_ENCODER_TVDAC,
+			       NULL);
+	if (ret) {
+		dev_err(dev, "Couldn't initialise the TV encoder\n");
+		goto err_disable_clk;
+	}
+
+	tv->encoder.possible_crtcs = BIT(0);
+
+	drm_connector_helper_add(&tv->connector,
+				 &sun4i_tv_comp_connector_helper_funcs);
+	ret = drm_connector_init(drm, &tv->connector,
+				 &sun4i_tv_comp_connector_funcs,
+				 DRM_MODE_CONNECTOR_Composite);
+	if (ret) {
+		dev_err(dev,
+			"Couldn't initialise the Composite connector\n");
+		goto err_cleanup_connector;
+	}
+	tv->connector.interlace_allowed = true;
+
+	drm_mode_connector_attach_encoder(&tv->connector, &tv->encoder);
+
+	return 0;
+
+err_cleanup_connector:
+	drm_encoder_cleanup(&tv->encoder);
+err_disable_clk:
+	clk_disable_unprepare(tv->clk);
+err_assert_reset:
+	reset_control_assert(tv->reset);
+	return ret;
+}
+
+static void sun4i_tv_unbind(struct device *dev, struct device *master,
+			    void *data)
+{
+	struct sun4i_tv *tv = dev_get_drvdata(dev);
+
+	drm_connector_cleanup(&tv->connector);
+	drm_encoder_cleanup(&tv->encoder);
+	clk_disable_unprepare(tv->clk);
+}
+
+static struct component_ops sun4i_tv_ops = {
+	.bind	= sun4i_tv_bind,
+	.unbind	= sun4i_tv_unbind,
+};
+
+static int sun4i_tv_probe(struct platform_device *pdev)
+{
+	return component_add(&pdev->dev, &sun4i_tv_ops);
+}
+
+static int sun4i_tv_remove(struct platform_device *pdev)
+{
+	component_del(&pdev->dev, &sun4i_tv_ops);
+
+	return 0;
+}
+
+static const struct of_device_id sun4i_tv_of_table[] = {
+	{ .compatible = "allwinner,sun4i-a10-tv-encoder" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, sun4i_tv_of_table);
+
+static struct platform_driver sun4i_tv_platform_driver = {
+	.probe		= sun4i_tv_probe,
+	.remove		= sun4i_tv_remove,
+	.driver		= {
+		.name		= "sun4i-tve",
+		.of_match_table	= sun4i_tv_of_table,
+	},
+};
+module_platform_driver(sun4i_tv_platform_driver);
+
+MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>");
+MODULE_DESCRIPTION("Allwinner A10 TV Encoder Driver");
+MODULE_LICENSE("GPL");
-- 
2.7.3

[PATCH v3 16/19] drm: sun4i: tv: Add PAL output standard

[Maxime Ripard]

Now that we have support for the composite output, we can start adding new
supported standards. Start with PAL, and we will add other eventually.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 drivers/gpu/drm/sun4i/sun4i_tv.c | 42 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 42 insertions(+)

diff --git a/drivers/gpu/drm/sun4i/sun4i_tv.c b/drivers/gpu/drm/sun4i/sun4i_tv.c
index 78634dfc0f77..ccf275a90132 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tv.c
+++ b/drivers/gpu/drm/sun4i/sun4i_tv.c
@@ -178,7 +178,49 @@ struct sun4i_tv {
 	struct sun4i_drv	*drv;
 };
 
+struct video_levels pal_video_levels = {
+	.black = 252,	.blank = 252,
+};
+
+struct burst_levels pal_burst_levels = {
+	.cb = 40,	.cr = 40,
+};
+
+struct color_gains pal_color_gains = {
+	.cb = 224,	.cr = 224,
+};
+
+struct resync_parameters pal_resync_parameters = {
+	.field = true,	.line = 13,	.pixel = 12,
+};
+
 struct tv_mode tv_modes[] = {
+	{
+		.name		= "PAL",
+		.mode		= SUN4I_TVE_CFG0_RES_576i,
+		.chroma_freq	= 0x2a098acb,
+
+		.back_porch	= 138,
+		.front_porch	= 24,
+		.line_number	= 625,
+
+		.hdisplay	= 720,
+		.hfront_porch	= 3,
+		.hsync_len	= 2,
+		.hback_porch	= 139,
+
+		.vdisplay	= 576,
+		.vfront_porch	= 28,
+		.vsync_len	= 2,
+		.vback_porch	= 19,
+
+		.vblank_level	= 252,
+
+		.color_gains	= &pal_color_gains,
+		.burst_levels	= &pal_burst_levels,
+		.video_levels	= &pal_video_levels,
+		.resync_params	= &pal_resync_parameters,
+	},
 };
 
 static inline struct sun4i_tv *
-- 
2.7.3

[PATCH v3 17/19] drm: sun4i: tv: Add NTSC output standard

[Maxime Ripard]

Add the settings to support the NTSC standard.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 drivers/gpu/drm/sun4i/sun4i_tv.c | 45 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 45 insertions(+)

diff --git a/drivers/gpu/drm/sun4i/sun4i_tv.c b/drivers/gpu/drm/sun4i/sun4i_tv.c
index ccf275a90132..bc047f923508 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tv.c
+++ b/drivers/gpu/drm/sun4i/sun4i_tv.c
@@ -178,24 +178,69 @@ struct sun4i_tv {
 	struct sun4i_drv	*drv;
 };
 
+struct video_levels ntsc_video_levels = {
+	.black = 282,	.blank = 240,
+};
+
 struct video_levels pal_video_levels = {
 	.black = 252,	.blank = 252,
 };
 
+struct burst_levels ntsc_burst_levels = {
+	.cb = 79,	.cr = 0,
+};
+
 struct burst_levels pal_burst_levels = {
 	.cb = 40,	.cr = 40,
 };
 
+struct color_gains ntsc_color_gains = {
+	.cb = 160,	.cr = 160,
+};
+
 struct color_gains pal_color_gains = {
 	.cb = 224,	.cr = 224,
 };
 
+struct resync_parameters ntsc_resync_parameters = {
+	.field = false,	.line = 14,	.pixel = 12,
+};
+
 struct resync_parameters pal_resync_parameters = {
 	.field = true,	.line = 13,	.pixel = 12,
 };
 
 struct tv_mode tv_modes[] = {
 	{
+		.name		= "NTSC",
+		.mode		= SUN4I_TVE_CFG0_RES_480i,
+		.chroma_freq	= 0x21f07c1f,
+		.yc_en		= true,
+		.dac3_en	= true,
+		.dac_bit25_en	= true,
+
+		.back_porch	= 118,
+		.front_porch	= 32,
+		.line_number	= 525,
+
+		.hdisplay	= 720,
+		.hfront_porch	= 18,
+		.hsync_len	= 2,
+		.hback_porch	= 118,
+
+		.vdisplay	= 480,
+		.vfront_porch	= 26,
+		.vsync_len	= 2,
+		.vback_porch	= 17,
+
+		.vblank_level	= 240,
+
+		.color_gains	= &ntsc_color_gains,
+		.burst_levels	= &ntsc_burst_levels,
+		.video_levels	= &ntsc_video_levels,
+		.resync_params	= &ntsc_resync_parameters,
+	},
+	{
 		.name		= "PAL",
 		.mode		= SUN4I_TVE_CFG0_RES_576i,
 		.chroma_freq	= 0x2a098acb,
-- 
2.7.3

[PATCH v3 18/19] ARM: sun5i: r8: Add display blocks to the DTSI

[Maxime Ripard]

The TCON, tv-encoder and display engine backends and frontends are combined
to create our display pipeline.

Add them to the R8 DTSI. It's supposed to be perfectly compatible with the
A10s and A13, but since we haven't tested it on them yet, it's safer to
just enable it on the R8. Eventually, it should be moved to sun5i.dtsi

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/sun5i-r8.dtsi | 137 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 137 insertions(+)

diff --git a/arch/arm/boot/dts/sun5i-r8.dtsi b/arch/arm/boot/dts/sun5i-r8.dtsi
index 691d3de75b35..df20b3b3ecfb 100644
--- a/arch/arm/boot/dts/sun5i-r8.dtsi
+++ b/arch/arm/boot/dts/sun5i-r8.dtsi
@@ -57,4 +57,141 @@
 			status = "disabled";
 		};
 	};
+
+	soc@01c00000 {
+		tve0: tv-encoder@01c0a000 {
+			compatible = "allwinner,sun4i-a10-tv-encoder";
+			reg = <0x01c0a000 0x1000>;
+			clocks = <&ahb_gates 34>;
+			resets = <&tcon_ch0_clk 0>;
+			status = "disabled";
+
+			port {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tve0_in_tcon0: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&tcon0_out_tve0>;
+				};
+			};
+		};
+
+		tcon0: lcd-controller@01c0c000 {
+			compatible = "allwinner,sun5i-a13-tcon";
+			reg = <0x01c0c000 0x1000>;
+			interrupts = <44>;
+			resets = <&tcon_ch0_clk 1>;
+			reset-names = "lcd";
+			clocks = <&ahb_gates 36>,
+				 <&tcon_ch0_clk>,
+				 <&tcon_ch1_clk>;
+			clock-names = "ahb",
+				      "tcon-ch0",
+				      "tcon-ch1";
+			clock-output-names = "tcon-pixel-clock";
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tcon0_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					tcon0_in_be0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&be0_out_tcon0>;
+					};
+				};
+
+				tcon0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					tcon0_out_tve0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&tve0_in_tcon0>;
+					};
+				};
+			};
+		};
+
+		fe0: display-frontend@01e00000 {
+			compatible = "allwinner,sun5i-a13-display-frontend";
+			reg = <0x01e00000 0x20000>;
+			interrupts = <47>;
+			clocks = <&ahb_gates 46>, <&de_fe_clk>,
+				 <&dram_gates 25>;
+			clock-names = "ahb", "mod",
+				      "ram";
+			resets = <&de_fe_clk>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fe0_out: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					fe0_out_be0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&be0_in_fe0>;
+					};
+				};
+			};
+		};
+
+		be0: display-backend@01e60000 {
+			compatible = "allwinner,sun5i-a13-display-backend";
+			reg = <0x01e60000 0x10000>;
+			clocks = <&ahb_gates 44>, <&de_be_clk>,
+				 <&dram_gates 26>;
+			clock-names = "ahb", "mod",
+				      "ram";
+			resets = <&de_be_clk>;
+			status = "disabled";
+
+			assigned-clocks = <&de_be_clk>;
+			assigned-clock-rates = <300000000>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				be0_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					be0_in_fe0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&fe0_out_be0>;
+					};
+				};
+
+				be0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					be0_out_tcon0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&tcon0_in_be0>;
+					};
+				};
+			};
+		};
+	};
+
+	display-engine {
+		compatible = "allwinner,sun5i-a13-display-engine";
+		pipelines = <&be0>;
+	};
 };
-- 
2.7.3

[PATCH v3 19/19] ARM: sun5i: chip: Enable the TV Encoder

[Maxime Ripard]

The CHIP has a composite output available muxed with the microphone in the
micro-jack plug.

Enable the composite output in its DTS.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/sun5i-r8-chip.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/sun5i-r8-chip.dts b/arch/arm/boot/dts/sun5i-r8-chip.dts
index f6898c6b84d4..a8d8b4582397 100644
--- a/arch/arm/boot/dts/sun5i-r8-chip.dts
+++ b/arch/arm/boot/dts/sun5i-r8-chip.dts
@@ -66,6 +66,10 @@
 	};
 };
 
+&be0 {
+	status = "okay";
+};
+
 &codec {
 	status = "okay";
 };
@@ -188,6 +192,14 @@
 	status = "okay";
 };
 
+&tcon0 {
+	status = "okay";
+};
+
+&tve0 {
+	status = "okay";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins_b>;
-- 
2.7.3

Re: [linux-sunxi] [PATCH v3 08/19] ARM: sun5i: Add DRAM gates

[Chen-Yu Tsai]

On Thu, Mar 24, 2016 at 12:38 AM, Maxime Ripard
<maxime.ripard@free-electrons.com> wrote:
> The DRAM gates control whether the image / display devices on the SoC have
> access to the DRAM clock or not.
>
> Enable it.
>
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Acked-by: Chen-Yu Tsai <wens@csie.org>

I assume you'll add another version for A10s, or move the whole thing
to sun5i.dtsi later?

Re: [PATCH v3 13/19] drm: sun4i: Add DT bindings documentation

[Rob Herring]

On Wed, Mar 23, 2016 at 05:38:36PM +0100, Maxime Ripard wrote:
> The display pipeline of the Allwinner A10 is involving several loosely
> coupled components.
> 
> Add a documentation for the bindings.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> ---
>  .../bindings/display/sunxi/sun4i-drm.txt           | 254 +++++++++++++++++++++
>  1 file changed, 254 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> 
> diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> new file mode 100644
> index 000000000000..378edb919eae
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> @@ -0,0 +1,254 @@
> +Allwinner A10 Display Pipeline
> +==============================
> +
> +The Allwinner A10 Display pipeline is composed of several components
> +that are going to be documented below:
> +
> +TV Encoder
> +----------
> +
> +The TV Encoder supports the composite and VGA output. It is one end of
> +the pipeline.
> +
> +Required properties:
> + - compatible: value should be "allwinner,sun4i-a10-tv-encoder".
> + - reg: base address and size of memory-mapped region
> + - clocks: the clocks driving the TV encoder
> + - resets: phandle to the reset controller driving the encoder
> +
> +- ports: A ports node with endpoint definitions as defined in
> +  Documentation/devicetree/bindings/media/video-interfaces.txt. The
> +  first port should be the input endpoint.
> +
> +TCON
> +----
> +
> +The TCON acts as a timing controller for RGB, LVDS and TV interfaces.
> +
> +Required properties:
> + - compatible: value should be "allwinner,sun5i-a13-tcon".
> + - reg: base address and size of memory-mapped region
> + - interrupts: interrupt associated to this IP
> + - clocks: phandles to the clocks feeding the TCON. Three are needed:
> +   - 'ahb': the interface clocks
> +   - 'tcon-ch0': The clock driving the TCON channel 0
> +   - 'tcon-ch1': The clock driving the TCON channel 1
> + - resets: phandles to the reset controllers driving the encoder
> +   - "lcd": the reset line for the TCON channel 0
> +
> + - clock-names: the clock names mentioned above
> + - reset-names: the reset names mentioned above
> + - clock-output-names: Name of the pixel clock created
> +
> +- ports: A ports node with endpoint definitions as defined in
> +  Documentation/devicetree/bindings/media/video-interfaces.txt. The
> +  first port should be the input endpoint, the second one the output

The example shows 2 output endpoints. Your diagram shows up to 4 
outputs. The number should be how ever many could coexist in a given h/w 
design. In other words, I'm assuming all 4 can't be used simultaneously, 
but can all 4 be wired up in a h/w design and switched in s/w? 

Just be clear on the numbering.

> +
> +Endpoints optional property:
> +  - allwinner,panel: boolean to indicate that the endpoint is a panel

This can be determined by the endpoint not being TV Encoder (or HDMI).

> +
> +
> +Display Engine Backend
> +----------------------
> +
> +The display engine backend exposes layers and sprites to the
> +system.
> +
> +Required properties:
> +  - compatible: value must be one of:
> +    * allwinner,sun5i-a13-display-backend
> +  - reg: base address and size of the memory-mapped region.
> +  - clocks: phandles to the clocks feeding the frontend and backend
> +    * ahb: the backend interface clock
> +    * mod: the backend module clock
> +    * ram: the backend DRAM clock
> +  - clock-names: the clock names mentioned above
> +  - resets: phandles to the reset controllers driving the backend
> +
> +- ports: A ports node with endpoint definitions as defined in
> +  Documentation/devicetree/bindings/media/video-interfaces.txt. The
> +  first port should be the input endpoints, the second one the output
> +
> +Display Engine Frontend
> +-----------------------
> +
> +The display engine frontend does formats conversion, scaling,
> +deinterlacing and color space conversion.
> +
> +Required properties:
> +  - compatible: value must be one of:
> +    * allwinner,sun5i-a13-display-frontend
> +  - reg: base address and size of the memory-mapped region.
> +  - interrupts: interrupt associated to this IP
> +  - clocks: phandles to the clocks feeding the frontend and backend
> +    * ahb: the backend interface clock
> +    * mod: the backend module clock
> +    * ram: the backend DRAM clock
> +  - clock-names: the clock names mentioned above
> +  - resets: phandles to the reset controllers driving the backend
> +
> +Display Engine Pipeline
> +-----------------------
> +
> +The display engine pipeline (and its entry point, since it can be
> +either directly the backend or the frontend) is represented as an
> +extra node.
> +
> +Required properties:
> +  - compatible: value must be one of:
> +    * allwinner,sun5i-a13-display-engine
> +  - allwinner,pipelines: list of phandle to the entry points of the
> +    pipelines (either to the frontend or backend)

Seems like using FE or BE would be a function of your framebuffers' 
formats and shouldn't be defined in DT.


> +
> +Example:
> +
> +panel: panel {
> +	compatible = "olimex,lcd-olinuxino-43-ts";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	port@0 {
> +		reg = <0>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		panel_input: endpoint@0 {
> +			reg = <0>;
> +			remote-endpoint = <&tcon0_out_panel>;

You can drop the unit-addresses and reg when there is only 1 (or 
leaving is fine too).

> +		};
> +	};
> +};
> +
> +tve0: tv-encoder@01c0a000 {

Drop the leading 0.

> +	compatible = "allwinner,sun4i-a10-tv-encoder";
> +	reg = <0x01c0a000 0x1000>;
> +	clocks = <&ahb_gates 34>;
> +	resets = <&tcon_ch0_clk 0>;
> +
> +	port {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		tve0_in_tcon0: endpoint@0 {
> +			reg = <0>;
> +			remote-endpoint = <&tcon0_out_tve0>;
> +		};
> +	};
> +};
> +
> +tcon0: lcd-controller@01c0c000 {

ditto...

> +	compatible = "allwinner,sun5i-a13-tcon";
> +	reg = <0x01c0c000 0x1000>;
> +	interrupts = <44>;
> +	resets = <&tcon_ch0_clk 1>;
> +	reset-names = "lcd";
> +	clocks = <&ahb_gates 36>,
> +		 <&tcon_ch0_clk>,
> +		 <&tcon_ch1_clk>;
> +	clock-names = "ahb",
> +		      "tcon-ch0",
> +		      "tcon-ch1";
> +	clock-output-names = "tcon-pixel-clock";

Re: [linux-sunxi] [PATCH v3 08/19] ARM: sun5i: Add DRAM gates

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 653 bytes --]

On Thu, Mar 24, 2016 at 12:31:13PM +0800, Chen-Yu Tsai wrote:
> On Thu, Mar 24, 2016 at 12:38 AM, Maxime Ripard
> <maxime.ripard@free-electrons.com> wrote:
> > The DRAM gates control whether the image / display devices on the SoC have
> > access to the DRAM clock or not.
> >
> > Enable it.
> >
> > Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> 
> Acked-by: Chen-Yu Tsai <wens@csie.org>
> 
> I assume you'll add another version for A10s, or move the whole thing
> to sun5i.dtsi later?

Indeed.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 13/19] drm: sun4i: Add DT bindings documentation

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 7581 bytes --]

Hi Rob,

On Fri, Mar 25, 2016 at 09:11:18AM -0500, Rob Herring wrote:
> On Wed, Mar 23, 2016 at 05:38:36PM +0100, Maxime Ripard wrote:
> > The display pipeline of the Allwinner A10 is involving several loosely
> > coupled components.
> > 
> > Add a documentation for the bindings.
> > 
> > Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> > ---
> >  .../bindings/display/sunxi/sun4i-drm.txt           | 254 +++++++++++++++++++++
> >  1 file changed, 254 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> > 
> > diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> > new file mode 100644
> > index 000000000000..378edb919eae
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> > @@ -0,0 +1,254 @@
> > +Allwinner A10 Display Pipeline
> > +==============================
> > +
> > +The Allwinner A10 Display pipeline is composed of several components
> > +that are going to be documented below:
> > +
> > +TV Encoder
> > +----------
> > +
> > +The TV Encoder supports the composite and VGA output. It is one end of
> > +the pipeline.
> > +
> > +Required properties:
> > + - compatible: value should be "allwinner,sun4i-a10-tv-encoder".
> > + - reg: base address and size of memory-mapped region
> > + - clocks: the clocks driving the TV encoder
> > + - resets: phandle to the reset controller driving the encoder
> > +
> > +- ports: A ports node with endpoint definitions as defined in
> > +  Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > +  first port should be the input endpoint.
> > +
> > +TCON
> > +----
> > +
> > +The TCON acts as a timing controller for RGB, LVDS and TV interfaces.
> > +
> > +Required properties:
> > + - compatible: value should be "allwinner,sun5i-a13-tcon".
> > + - reg: base address and size of memory-mapped region
> > + - interrupts: interrupt associated to this IP
> > + - clocks: phandles to the clocks feeding the TCON. Three are needed:
> > +   - 'ahb': the interface clocks
> > +   - 'tcon-ch0': The clock driving the TCON channel 0
> > +   - 'tcon-ch1': The clock driving the TCON channel 1
> > + - resets: phandles to the reset controllers driving the encoder
> > +   - "lcd": the reset line for the TCON channel 0
> > +
> > + - clock-names: the clock names mentioned above
> > + - reset-names: the reset names mentioned above
> > + - clock-output-names: Name of the pixel clock created
> > +
> > +- ports: A ports node with endpoint definitions as defined in
> > +  Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > +  first port should be the input endpoint, the second one the output
> 
> The example shows 2 output endpoints. Your diagram shows up to 4 
> outputs. The number should be how ever many could coexist in a given h/w 
> design. In other words, I'm assuming all 4 can't be used simultaneously, 
> but can all 4 be wired up in a h/w design and switched in s/w? 
> 
> Just be clear on the numbering.

Yes, each TCON has two channels, the first one being usable for
RGB/LVDS, the second one for TV/VGA. HDMI is basically implemented
using an in-SoC RGB-to-HDMI bridge, so it would use the first channel
as well.

I don't see how a particular design could use several devices on the
first channel, because they would share the same timings, and I don't
really see how it would work out.

> > +
> > +Endpoints optional property:
> > +  - allwinner,panel: boolean to indicate that the endpoint is a panel
> 
> This can be determined by the endpoint not being TV Encoder (or HDMI).

It wouldn't really scale if you start to consider the bridges
too. Then, you would have to duplicate and maintain a list of all the
bridges supported in Linux and a list of all the panels supported in
Linux, and try to match that to see if it's a panel, a bridge or an
element of our pipeline.

> 
> > +
> > +
> > +Display Engine Backend
> > +----------------------
> > +
> > +The display engine backend exposes layers and sprites to the
> > +system.
> > +
> > +Required properties:
> > +  - compatible: value must be one of:
> > +    * allwinner,sun5i-a13-display-backend
> > +  - reg: base address and size of the memory-mapped region.
> > +  - clocks: phandles to the clocks feeding the frontend and backend
> > +    * ahb: the backend interface clock
> > +    * mod: the backend module clock
> > +    * ram: the backend DRAM clock
> > +  - clock-names: the clock names mentioned above
> > +  - resets: phandles to the reset controllers driving the backend
> > +
> > +- ports: A ports node with endpoint definitions as defined in
> > +  Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > +  first port should be the input endpoints, the second one the output
> > +
> > +Display Engine Frontend
> > +-----------------------
> > +
> > +The display engine frontend does formats conversion, scaling,
> > +deinterlacing and color space conversion.
> > +
> > +Required properties:
> > +  - compatible: value must be one of:
> > +    * allwinner,sun5i-a13-display-frontend
> > +  - reg: base address and size of the memory-mapped region.
> > +  - interrupts: interrupt associated to this IP
> > +  - clocks: phandles to the clocks feeding the frontend and backend
> > +    * ahb: the backend interface clock
> > +    * mod: the backend module clock
> > +    * ram: the backend DRAM clock
> > +  - clock-names: the clock names mentioned above
> > +  - resets: phandles to the reset controllers driving the backend
> > +
> > +Display Engine Pipeline
> > +-----------------------
> > +
> > +The display engine pipeline (and its entry point, since it can be
> > +either directly the backend or the frontend) is represented as an
> > +extra node.
> > +
> > +Required properties:
> > +  - compatible: value must be one of:
> > +    * allwinner,sun5i-a13-display-engine
> > +  - allwinner,pipelines: list of phandle to the entry points of the
> > +    pipelines (either to the frontend or backend)
> 
> Seems like using FE or BE would be a function of your framebuffers' 
> formats and shouldn't be defined in DT.

Well, they are different IP blocks, so it should be defined in DT,
shouldn't it?

> 
> > +
> > +Example:
> > +
> > +panel: panel {
> > +	compatible = "olimex,lcd-olinuxino-43-ts";
> > +	#address-cells = <1>;
> > +	#size-cells = <0>;
> > +
> > +	port@0 {
> > +		reg = <0>;
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +
> > +		panel_input: endpoint@0 {
> > +			reg = <0>;
> > +			remote-endpoint = <&tcon0_out_panel>;
> 
> You can drop the unit-addresses and reg when there is only 1 (or 
> leaving is fine too).
> 
> > +		};
> > +	};
> > +};
> > +
> > +tve0: tv-encoder@01c0a000 {
> 
> Drop the leading 0.

Ok.

> 
> > +	compatible = "allwinner,sun4i-a10-tv-encoder";
> > +	reg = <0x01c0a000 0x1000>;
> > +	clocks = <&ahb_gates 34>;
> > +	resets = <&tcon_ch0_clk 0>;
> > +
> > +	port {
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +
> > +		tve0_in_tcon0: endpoint@0 {
> > +			reg = <0>;
> > +			remote-endpoint = <&tcon0_out_tve0>;
> > +		};
> > +	};
> > +};
> > +
> > +tcon0: lcd-controller@01c0c000 {
> 
> ditto...

Ok.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 13/19] drm: sun4i: Add DT bindings documentation

[Rob Herring]

On Tue, Mar 29, 2016 at 12:33:14PM +0200, Maxime Ripard wrote:
> Hi Rob,
> 
> On Fri, Mar 25, 2016 at 09:11:18AM -0500, Rob Herring wrote:
> > On Wed, Mar 23, 2016 at 05:38:36PM +0100, Maxime Ripard wrote:
> > > The display pipeline of the Allwinner A10 is involving several loosely
> > > coupled components.
> > > 
> > > Add a documentation for the bindings.
> > > 
> > > Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> > > ---
> > >  .../bindings/display/sunxi/sun4i-drm.txt           | 254 +++++++++++++++++++++
> > >  1 file changed, 254 insertions(+)
> > >  create mode 100644 Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> > > 
> > > diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> > > new file mode 100644
> > > index 000000000000..378edb919eae
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> > > @@ -0,0 +1,254 @@
> > > +Allwinner A10 Display Pipeline
> > > +==============================
> > > +
> > > +The Allwinner A10 Display pipeline is composed of several components
> > > +that are going to be documented below:
> > > +
> > > +TV Encoder
> > > +----------
> > > +
> > > +The TV Encoder supports the composite and VGA output. It is one end of
> > > +the pipeline.
> > > +
> > > +Required properties:
> > > + - compatible: value should be "allwinner,sun4i-a10-tv-encoder".
> > > + - reg: base address and size of memory-mapped region
> > > + - clocks: the clocks driving the TV encoder
> > > + - resets: phandle to the reset controller driving the encoder
> > > +
> > > +- ports: A ports node with endpoint definitions as defined in
> > > +  Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > > +  first port should be the input endpoint.
> > > +
> > > +TCON
> > > +----
> > > +
> > > +The TCON acts as a timing controller for RGB, LVDS and TV interfaces.
> > > +
> > > +Required properties:
> > > + - compatible: value should be "allwinner,sun5i-a13-tcon".
> > > + - reg: base address and size of memory-mapped region
> > > + - interrupts: interrupt associated to this IP
> > > + - clocks: phandles to the clocks feeding the TCON. Three are needed:
> > > +   - 'ahb': the interface clocks
> > > +   - 'tcon-ch0': The clock driving the TCON channel 0
> > > +   - 'tcon-ch1': The clock driving the TCON channel 1
> > > + - resets: phandles to the reset controllers driving the encoder
> > > +   - "lcd": the reset line for the TCON channel 0
> > > +
> > > + - clock-names: the clock names mentioned above
> > > + - reset-names: the reset names mentioned above
> > > + - clock-output-names: Name of the pixel clock created
> > > +
> > > +- ports: A ports node with endpoint definitions as defined in
> > > +  Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > > +  first port should be the input endpoint, the second one the output
> > 
> > The example shows 2 output endpoints. Your diagram shows up to 4 
> > outputs. The number should be how ever many could coexist in a given h/w 
> > design. In other words, I'm assuming all 4 can't be used simultaneously, 
> > but can all 4 be wired up in a h/w design and switched in s/w? 
> > 
> > Just be clear on the numbering.
> 
> Yes, each TCON has two channels, the first one being usable for
> RGB/LVDS, the second one for TV/VGA. HDMI is basically implemented
> using an in-SoC RGB-to-HDMI bridge, so it would use the first channel
> as well.

So I think you should have 2 ports (1 per channel) and then 2 endpoints 
for 1st (RGB/LVDS/ExtBridge and HDMI) and 1 endpoint (TV/VGA) for 2nd 
port.

> I don't see how a particular design could use several devices on the
> first channel, because they would share the same timings, and I don't
> really see how it would work out.
> 
> > > +
> > > +Endpoints optional property:
> > > +  - allwinner,panel: boolean to indicate that the endpoint is a panel
> > 
> > This can be determined by the endpoint not being TV Encoder (or HDMI).
> 
> It wouldn't really scale if you start to consider the bridges
> too. Then, you would have to duplicate and maintain a list of all the
> bridges supported in Linux and a list of all the panels supported in
> Linux, and try to match that to see if it's a panel, a bridge or an
> element of our pipeline.

So my concern is that no one else has needed this, so why do you? Based 
on the above, you know that a panel is always connected to port 0, 
endpoint 0. If it is an external bridge instead, then that can be 
determined when the bridge driver is bound.


> > > +Display Engine Backend
> > > +----------------------
> > > +
> > > +The display engine backend exposes layers and sprites to the
> > > +system.
> > > +
> > > +Required properties:
> > > +  - compatible: value must be one of:
> > > +    * allwinner,sun5i-a13-display-backend
> > > +  - reg: base address and size of the memory-mapped region.
> > > +  - clocks: phandles to the clocks feeding the frontend and backend
> > > +    * ahb: the backend interface clock
> > > +    * mod: the backend module clock
> > > +    * ram: the backend DRAM clock
> > > +  - clock-names: the clock names mentioned above
> > > +  - resets: phandles to the reset controllers driving the backend
> > > +
> > > +- ports: A ports node with endpoint definitions as defined in
> > > +  Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > > +  first port should be the input endpoints, the second one the output
> > > +
> > > +Display Engine Frontend
> > > +-----------------------
> > > +
> > > +The display engine frontend does formats conversion, scaling,
> > > +deinterlacing and color space conversion.
> > > +
> > > +Required properties:
> > > +  - compatible: value must be one of:
> > > +    * allwinner,sun5i-a13-display-frontend
> > > +  - reg: base address and size of the memory-mapped region.
> > > +  - interrupts: interrupt associated to this IP
> > > +  - clocks: phandles to the clocks feeding the frontend and backend
> > > +    * ahb: the backend interface clock
> > > +    * mod: the backend module clock
> > > +    * ram: the backend DRAM clock
> > > +  - clock-names: the clock names mentioned above
> > > +  - resets: phandles to the reset controllers driving the backend
> > > +
> > > +Display Engine Pipeline
> > > +-----------------------
> > > +
> > > +The display engine pipeline (and its entry point, since it can be
> > > +either directly the backend or the frontend) is represented as an
> > > +extra node.
> > > +
> > > +Required properties:
> > > +  - compatible: value must be one of:
> > > +    * allwinner,sun5i-a13-display-engine
> > > +  - allwinner,pipelines: list of phandle to the entry points of the
> > > +    pipelines (either to the frontend or backend)
> > 
> > Seems like using FE or BE would be a function of your framebuffers' 
> > formats and shouldn't be defined in DT.
> 
> Well, they are different IP blocks, so it should be defined in DT,
> shouldn't it?

They should, but allwinner,sun5i-a13-display-engine is not really an IP 
block. Again, what decides if you use the FE or not?

Rob

Re: [PATCH v3 13/19] drm: sun4i: Add DT bindings documentation

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 8205 bytes --]

Hi Rob,

On Tue, Mar 29, 2016 at 01:50:35PM -0500, Rob Herring wrote:
> On Tue, Mar 29, 2016 at 12:33:14PM +0200, Maxime Ripard wrote:
> > Hi Rob,
> > 
> > On Fri, Mar 25, 2016 at 09:11:18AM -0500, Rob Herring wrote:
> > > On Wed, Mar 23, 2016 at 05:38:36PM +0100, Maxime Ripard wrote:
> > > > The display pipeline of the Allwinner A10 is involving several loosely
> > > > coupled components.
> > > > 
> > > > Add a documentation for the bindings.
> > > > 
> > > > Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> > > > ---
> > > >  .../bindings/display/sunxi/sun4i-drm.txt           | 254 +++++++++++++++++++++
> > > >  1 file changed, 254 insertions(+)
> > > >  create mode 100644 Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> > > > 
> > > > diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> > > > new file mode 100644
> > > > index 000000000000..378edb919eae
> > > > --- /dev/null
> > > > +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> > > > @@ -0,0 +1,254 @@
> > > > +Allwinner A10 Display Pipeline
> > > > +==============================
> > > > +
> > > > +The Allwinner A10 Display pipeline is composed of several components
> > > > +that are going to be documented below:
> > > > +
> > > > +TV Encoder
> > > > +----------
> > > > +
> > > > +The TV Encoder supports the composite and VGA output. It is one end of
> > > > +the pipeline.
> > > > +
> > > > +Required properties:
> > > > + - compatible: value should be "allwinner,sun4i-a10-tv-encoder".
> > > > + - reg: base address and size of memory-mapped region
> > > > + - clocks: the clocks driving the TV encoder
> > > > + - resets: phandle to the reset controller driving the encoder
> > > > +
> > > > +- ports: A ports node with endpoint definitions as defined in
> > > > +  Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > > > +  first port should be the input endpoint.
> > > > +
> > > > +TCON
> > > > +----
> > > > +
> > > > +The TCON acts as a timing controller for RGB, LVDS and TV interfaces.
> > > > +
> > > > +Required properties:
> > > > + - compatible: value should be "allwinner,sun5i-a13-tcon".
> > > > + - reg: base address and size of memory-mapped region
> > > > + - interrupts: interrupt associated to this IP
> > > > + - clocks: phandles to the clocks feeding the TCON. Three are needed:
> > > > +   - 'ahb': the interface clocks
> > > > +   - 'tcon-ch0': The clock driving the TCON channel 0
> > > > +   - 'tcon-ch1': The clock driving the TCON channel 1
> > > > + - resets: phandles to the reset controllers driving the encoder
> > > > +   - "lcd": the reset line for the TCON channel 0
> > > > +
> > > > + - clock-names: the clock names mentioned above
> > > > + - reset-names: the reset names mentioned above
> > > > + - clock-output-names: Name of the pixel clock created
> > > > +
> > > > +- ports: A ports node with endpoint definitions as defined in
> > > > +  Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > > > +  first port should be the input endpoint, the second one the output
> > > 
> > > The example shows 2 output endpoints. Your diagram shows up to 4 
> > > outputs. The number should be how ever many could coexist in a given h/w 
> > > design. In other words, I'm assuming all 4 can't be used simultaneously, 
> > > but can all 4 be wired up in a h/w design and switched in s/w? 
> > > 
> > > Just be clear on the numbering.
> > 
> > Yes, each TCON has two channels, the first one being usable for
> > RGB/LVDS, the second one for TV/VGA. HDMI is basically implemented
> > using an in-SoC RGB-to-HDMI bridge, so it would use the first channel
> > as well.
> 
> So I think you should have 2 ports (1 per channel) and then 2 endpoints 
> for 1st (RGB/LVDS/ExtBridge and HDMI) and 1 endpoint (TV/VGA) for 2nd 
> port.

Yes, that makes sense.

> > I don't see how a particular design could use several devices on the
> > first channel, because they would share the same timings, and I don't
> > really see how it would work out.
> > 
> > > > +
> > > > +Endpoints optional property:
> > > > +  - allwinner,panel: boolean to indicate that the endpoint is a panel
> > > 
> > > This can be determined by the endpoint not being TV Encoder (or HDMI).
> > 
> > It wouldn't really scale if you start to consider the bridges
> > too. Then, you would have to duplicate and maintain a list of all the
> > bridges supported in Linux and a list of all the panels supported in
> > Linux, and try to match that to see if it's a panel, a bridge or an
> > element of our pipeline.
> 
> So my concern is that no one else has needed this, so why do you? Based 
> on the above, you know that a panel is always connected to port 0, 
> endpoint 0. If it is an external bridge instead, then that can be 
> determined when the bridge driver is bound.

Indeed, I'll try to use the panel and bridge API to retrieve the panel
and bridges drivers, and try to derive the information from that
instead of this DT property.

> > > > +Display Engine Backend
> > > > +----------------------
> > > > +
> > > > +The display engine backend exposes layers and sprites to the
> > > > +system.
> > > > +
> > > > +Required properties:
> > > > +  - compatible: value must be one of:
> > > > +    * allwinner,sun5i-a13-display-backend
> > > > +  - reg: base address and size of the memory-mapped region.
> > > > +  - clocks: phandles to the clocks feeding the frontend and backend
> > > > +    * ahb: the backend interface clock
> > > > +    * mod: the backend module clock
> > > > +    * ram: the backend DRAM clock
> > > > +  - clock-names: the clock names mentioned above
> > > > +  - resets: phandles to the reset controllers driving the backend
> > > > +
> > > > +- ports: A ports node with endpoint definitions as defined in
> > > > +  Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > > > +  first port should be the input endpoints, the second one the output
> > > > +
> > > > +Display Engine Frontend
> > > > +-----------------------
> > > > +
> > > > +The display engine frontend does formats conversion, scaling,
> > > > +deinterlacing and color space conversion.
> > > > +
> > > > +Required properties:
> > > > +  - compatible: value must be one of:
> > > > +    * allwinner,sun5i-a13-display-frontend
> > > > +  - reg: base address and size of the memory-mapped region.
> > > > +  - interrupts: interrupt associated to this IP
> > > > +  - clocks: phandles to the clocks feeding the frontend and backend
> > > > +    * ahb: the backend interface clock
> > > > +    * mod: the backend module clock
> > > > +    * ram: the backend DRAM clock
> > > > +  - clock-names: the clock names mentioned above
> > > > +  - resets: phandles to the reset controllers driving the backend
> > > > +
> > > > +Display Engine Pipeline
> > > > +-----------------------
> > > > +
> > > > +The display engine pipeline (and its entry point, since it can be
> > > > +either directly the backend or the frontend) is represented as an
> > > > +extra node.
> > > > +
> > > > +Required properties:
> > > > +  - compatible: value must be one of:
> > > > +    * allwinner,sun5i-a13-display-engine
> > > > +  - allwinner,pipelines: list of phandle to the entry points of the
> > > > +    pipelines (either to the frontend or backend)
> > > 
> > > Seems like using FE or BE would be a function of your framebuffers' 
> > > formats and shouldn't be defined in DT.
> > 
> > Well, they are different IP blocks, so it should be defined in DT,
> > shouldn't it?
> 
> They should, but allwinner,sun5i-a13-display-engine is not really an IP 
> block. Again, what decides if you use the FE or not?

I'd say we would always want to use it, but we don't have support for
it right now. You can use the backend directly, and this is what we're
doing right now.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 01/19] clk: composite: Add unregister function

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 702 bytes --]

Hi Stephen, Mike,

On Wed, Mar 23, 2016 at 05:38:24PM +0100, Maxime Ripard wrote:
> The composite clock didn't have any unregistration function, which forced
> us to use clk_unregister directly on it.
> 
> While it was already not great from an API point of view, it also meant
> that we were leaking the clk_composite structure allocated in
> clk_register_composite.
> 
> Add a clk_unregister_composite function to fix this.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Any comment on this one ?

(and the other clock patches)

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 11/19] drm/panel: simple: Add timings for the Olimex LCD-OLinuXino-4.3TS

[Thierry Reding]

[-- Attachment #1: Type: text/plain, Size: 669 bytes --]

On Wed, Mar 23, 2016 at 05:38:34PM +0100, Maxime Ripard wrote:
> Add support for the Olimex LCD-OLinuXino-4.3TS panel to the DRM simple
> panel driver.
> 
> It is a 480x272 panel connected through a 24-bits RGB interface.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> Acked-by: Rob Herring <robh@kernel.org>
> ---
>  .../display/panel/olimex,lcd-olinuxino-43-ts.txt   |  7 ++++++
>  drivers/gpu/drm/panel/panel-simple.c               | 26 ++++++++++++++++++++++
>  2 files changed, 33 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt

Applied, thanks.

Thierry

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 01/19] clk: composite: Add unregister function

[Stephen Boyd]

On 03/23, Maxime Ripard wrote:
> The composite clock didn't have any unregistration function, which forced
> us to use clk_unregister directly on it.
> 
> While it was already not great from an API point of view, it also meant
> that we were leaking the clk_composite structure allocated in
> clk_register_composite.
> 
> Add a clk_unregister_composite function to fix this.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> ---

I'm currently attempting to change the way clks are registered so
that we don't return clk pointers from clk_register and have
users add OF clk providers that return clk_hw pointers instead of
clk pointers. Just a note, that this whole thing should be
deleted in the next cycle if I can convert everything!

>  drivers/clk/clk-composite.c  | 15 +++++++++++++++
>  include/linux/clk-provider.h |  1 +
>  2 files changed, 16 insertions(+)
> 
> diff --git a/drivers/clk/clk-composite.c b/drivers/clk/clk-composite.c
> index 1f903e1f86a2..b0f3b84ebd13 100644
> --- a/drivers/clk/clk-composite.c
> +++ b/drivers/clk/clk-composite.c
> @@ -286,3 +286,18 @@ err:
>  	kfree(composite);
>  	return clk;
>  }
> +
> +void clk_unregister_composite(struct clk *clk)
> +{
> +	struct clk_composite *composite;
> +	struct clk_hw *hw;
> +
> +	hw = __clk_get_hw(clk);
> +	if (!hw)
> +		return;
> +
> +	composite = to_clk_composite(hw);
> +
> +	clk_unregister(clk);
> +	kfree(composite);
> +}

EXPORT_SYMBOL_GPL?

Do I need to pick this up?

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH v3 05/19] dt-bindings: clk: sun5i: add DRAM gates compatible

[Stephen Boyd]

On 03/23, Maxime Ripard wrote:
> The Allwinner SoCs have a gate controller to gate the access to the DRAM
> clock to the some devices that need to access the DRAM directly (mostly
> display / image related IPs).
> 
> Use a simple gates driver to support the one found in the A13 / R8 SoCs.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> Acked-by: Chen-Yu Tsai <wens@csie.org>
> Acked-by: Rob Herring <robh@kernel.org>
> ---

Acked-by: Stephen Boyd <sboyd@codeaurora.org>

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH v3 02/19] clk: sunxi: Add display and TCON0 clocks driver

[Stephen Boyd]

On 03/23, Maxime Ripard wrote:
> diff --git a/drivers/clk/sunxi/clk-sun4i-display.c b/drivers/clk/sunxi/clk-sun4i-display.c
> new file mode 100644
> index 000000000000..af7d1faebdec
> --- /dev/null
> +++ b/drivers/clk/sunxi/clk-sun4i-display.c
> @@ -0,0 +1,262 @@
> +#include <linux/clk-provider.h>
> +#include <linux/kernel.h>
> +#include <linux/of_address.h>
> +#include <linux/reset-controller.h>
> +#include <linux/slab.h>
> +#include <linux/spinlock.h>
> +
> +struct sun4i_a10_display_clk_data {
> +	bool	has_div;
> +	u8	has_rst;

Can this be num_resets? It's not a bool but name starts with
"has".

> +	u8	parents;
> +
> +	u8	offset_en;
> +	u8	offset_div;
> +	u8	offset_mux;
> +	u8	offset_rst;
> +
> +	u8	width_div;
> +	u8	width_mux;
> +};
> +
> +
> +static int sun4i_a10_display_reset_xlate(struct reset_controller_dev *rcdev,
> +					 const struct of_phandle_args *spec)
> +{
> +	/* We only have a single reset signal */
> +	return 0;
> +}

Is there a default function for this case in the reset framework?

> +
> +static void __init sun4i_a10_display_init(struct device_node *node,
> +					  struct sun4i_a10_display_clk_data *data)

const?

> +{
> +	const char *parents[data->parents];
> +	const char *clk_name = node->name;
> +	struct reset_data *reset_data;
> +	struct clk_divider *div = NULL;
> +	struct clk_gate *gate;
> +	struct resource res;
> +	struct clk_mux *mux;
> +	void __iomem *reg;
> +	struct clk *clk;
> +	int ret;
> +
> +	of_property_read_string(node, "clock-output-names", &clk_name);
> +
> +	reg = of_io_request_and_map(node, 0, of_node_full_name(node));
> +	if (IS_ERR(reg)) {
> +		pr_err("%s: Could not map the clock registers\n", clk_name);
> +		return;
> +	}
> +
> +	ret = of_clk_parent_fill(node, parents, data->parents);
> +	if (ret != data->parents) {
> +		pr_err("%s Could not retrieve the parents\n", clk_name);

Missing ':'?

> +		goto unmap;
> +	}
> +
[..]
> +
> +	ret = of_clk_add_provider(node, of_clk_src_simple_get, clk);
> +	if (ret) {
> +		pr_err("%s: Couldn't register DT provider\n", clk_name);
> +		goto free_clk;
> +	}
> +
> +	if (!data->has_rst)
> +		return;
> +
> +	reset_data = kzalloc(sizeof(*reset_data), GFP_KERNEL);
> +	if (!reset_data)
> +		goto free_of_clk;
> +
> +	reset_data->reg = reg;
> +	reset_data->offset = data->offset_rst;
> +	reset_data->lock = &sun4i_a10_display_lock;
> +	reset_data->rcdev.nr_resets = data->has_rst;
> +	reset_data->rcdev.ops = &sun4i_a10_display_reset_ops;
> +	reset_data->rcdev.of_node = node;
> +
> +	if (data->has_rst == 1) {
> +		reset_data->rcdev.of_reset_n_cells = 0;
> +		reset_data->rcdev.of_xlate = &sun4i_a10_display_reset_xlate;
> +	} else {
> +		reset_data->rcdev.of_reset_n_cells = 1;
> +	}
> +
> +	if (reset_controller_register(&reset_data->rcdev)) {
> +		pr_err("%s: Couldn't register the reset controller\n",
> +		       clk_name);
> +		goto free_reset;
> +	}
> +
> +	return;
> +
> +free_reset:
> +	kfree(reset_data);
> +free_of_clk:
> +	of_clk_del_provider(node);
> +free_clk:
> +	clk_unregister_composite(clk);
> +free_div:
> +	if (data->has_div)

Do you need this check? div is NULL so I think no.

> +		kfree(div);
> +free_gate:
> +	kfree(gate);
> +free_mux:
> +	kfree(mux);
> +unmap:
> +	iounmap(reg);
> +	of_address_to_resource(node, 0, &res);
> +	release_mem_region(res.start, resource_size(&res));
> +}
> +
> +static struct sun4i_a10_display_clk_data sun4i_a10_tcon_ch0_data = {

const?

> +	.has_rst	= 2,
> +	.parents	= 4,
> +	.offset_en	= 31,
> +	.offset_rst	= 29,
> +	.offset_mux	= 24,
> +	.width_mux	= 2,
> +};
> +
> +static void __init sun4i_a10_tcon_ch0_setup(struct device_node *node)
> +{
> +	sun4i_a10_display_init(node, &sun4i_a10_tcon_ch0_data);
> +}
> +CLK_OF_DECLARE(sun4i_a10_tcon_ch0, "allwinner,sun4i-a10-tcon-ch0-clk",
> +	       sun4i_a10_tcon_ch0_setup);
> +
> +static struct sun4i_a10_display_clk_data sun4i_a10_display_data = {

const?

> +	.has_div	= true,
> +	.has_rst	= 1,
> +	.parents	= 3,
> +	.offset_en	= 31,
> +	.offset_rst	= 30,
> +	.offset_mux	= 24,
> +	.offset_div	= 0,
> +	.width_mux	= 2,
> +	.width_div	= 4,
> +};
> +
> +static void __init sun4i_a10_display_setup(struct device_node *node)
> +{
> +	sun4i_a10_display_init(node, &sun4i_a10_display_data);
> +}
> +CLK_OF_DECLARE(sun4i_a10_display, "allwinner,sun4i-a10-display-clk",
> +	       sun4i_a10_display_setup);

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH v3 03/19] clk: sunxi: Add PLL3 clock

[Stephen Boyd]

On 03/23, Maxime Ripard wrote:
> The A10 SoCs and relatives have a PLL controller to drive the PLL3 and
> PLL7, clocked from a 3MHz oscillator, that drives the display related
> clocks (GPU, display engine, TCON, etc.)
> 
> Add a driver for it.
> 
> Acked-by: Rob Herring <robh@kernel.org>
> Acked-by: Chen-Yu Tsai <wens@csie.org>
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> ---

Acked-by: Stephen Boyd <sboyd@codeaurora.org>

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH v3 04/19] clk: sunxi: Add TCON channel1 clock

[Stephen Boyd]

On 03/23, Maxime Ripard wrote:
> The TCON is a controller generating the timings to output videos signals,
> acting like both a CRTC and an encoder.
> 
> It has two channels depending on the output, each channel being driven by
> its own clock (and own clock controller).
> 
> Add a driver for the channel 1 clock.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> Acked-by: Rob Herring <robh@kernel.org>
> ---

Acked-by: Stephen Boyd <sboyd@codeaurora.org>

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH v3 05/19] dt-bindings: clk: sun5i: add DRAM gates compatible

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 738 bytes --]

On Fri, Apr 15, 2016 at 03:29:11PM -0700, Stephen Boyd wrote:
> On 03/23, Maxime Ripard wrote:
> > The Allwinner SoCs have a gate controller to gate the access to the DRAM
> > clock to the some devices that need to access the DRAM directly (mostly
> > display / image related IPs).
> > 
> > Use a simple gates driver to support the one found in the A13 / R8 SoCs.
> > 
> > Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> > Acked-by: Chen-Yu Tsai <wens@csie.org>
> > Acked-by: Rob Herring <robh@kernel.org>
> > ---
> 
> Acked-by: Stephen Boyd <sboyd@codeaurora.org>

Applied, thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 03/19] clk: sunxi: Add PLL3 clock

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 693 bytes --]

On Fri, Apr 15, 2016 at 03:34:41PM -0700, Stephen Boyd wrote:
> On 03/23, Maxime Ripard wrote:
> > The A10 SoCs and relatives have a PLL controller to drive the PLL3 and
> > PLL7, clocked from a 3MHz oscillator, that drives the display related
> > clocks (GPU, display engine, TCON, etc.)
> > 
> > Add a driver for it.
> > 
> > Acked-by: Rob Herring <robh@kernel.org>
> > Acked-by: Chen-Yu Tsai <wens@csie.org>
> > Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> > ---
> 
> Acked-by: Stephen Boyd <sboyd@codeaurora.org>

Applied, thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 01/19] clk: composite: Add unregister function

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 2121 bytes --]

Hi,

On Fri, Apr 15, 2016 at 03:28:56PM -0700, Stephen Boyd wrote:
> On 03/23, Maxime Ripard wrote:
> > The composite clock didn't have any unregistration function, which forced
> > us to use clk_unregister directly on it.
> > 
> > While it was already not great from an API point of view, it also meant
> > that we were leaking the clk_composite structure allocated in
> > clk_register_composite.
> > 
> > Add a clk_unregister_composite function to fix this.
> > 
> > Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> > ---
> 
> I'm currently attempting to change the way clks are registered so
> that we don't return clk pointers from clk_register and have
> users add OF clk providers that return clk_hw pointers instead of
> clk pointers. Just a note, that this whole thing should be
> deleted in the next cycle if I can convert everything!

Ok.

> 
> >  drivers/clk/clk-composite.c  | 15 +++++++++++++++
> >  include/linux/clk-provider.h |  1 +
> >  2 files changed, 16 insertions(+)
> > 
> > diff --git a/drivers/clk/clk-composite.c b/drivers/clk/clk-composite.c
> > index 1f903e1f86a2..b0f3b84ebd13 100644
> > --- a/drivers/clk/clk-composite.c
> > +++ b/drivers/clk/clk-composite.c
> > @@ -286,3 +286,18 @@ err:
> >  	kfree(composite);
> >  	return clk;
> >  }
> > +
> > +void clk_unregister_composite(struct clk *clk)
> > +{
> > +	struct clk_composite *composite;
> > +	struct clk_hw *hw;
> > +
> > +	hw = __clk_get_hw(clk);
> > +	if (!hw)
> > +		return;
> > +
> > +	composite = to_clk_composite(hw);
> > +
> > +	clk_unregister(clk);
> > +	kfree(composite);
> > +}
> 
> EXPORT_SYMBOL_GPL?

The register function is not registered, so I don't think that's
necessary.

> Do I need to pick this up?

I have a bunch of other clock patches that need this, so I guess it
would be easier if applied it directly with your acked-by, or if you
could apply it and give a stable branch I can base my future PR on.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 06/19] ARM: sun5i: dt: Add pll3 and pll7 clocks

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 411 bytes --]

On Wed, Mar 23, 2016 at 05:38:29PM +0100, Maxime Ripard wrote:
> Enable the pll3 and pll7 clocks in the DT that are used to drive the
> display-related clocks.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> Acked-by: Chen-Yu Tsai <wens@csie.org>

Applied,

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 09/19] ARM: sun5i: Add TV encoder gate to the DTSI

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 424 bytes --]

On Wed, Mar 23, 2016 at 05:38:32PM +0100, Maxime Ripard wrote:
> It turns out that the A13 / R8 also have a tve encoder block, and a gate
> for it.
> 
> Add it to the DT.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> Acked-by: Chen-Yu Tsai <wens@csie.org>

Applied,

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 08/19] ARM: sun5i: Add DRAM gates

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 400 bytes --]

On Wed, Mar 23, 2016 at 05:38:31PM +0100, Maxime Ripard wrote:
> The DRAM gates control whether the image / display devices on the SoC have
> access to the DRAM clock or not.
> 
> Enable it.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Applied,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 02/19] clk: sunxi: Add display and TCON0 clocks driver

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 682 bytes --]

Hi Stephen,

On Fri, Apr 15, 2016 at 03:34:10PM -0700, Stephen Boyd wrote:
> > +static int sun4i_a10_display_reset_xlate(struct reset_controller_dev *rcdev,
> > +					 const struct of_phandle_args *spec)
> > +{
> > +	/* We only have a single reset signal */
> > +	return 0;
> > +}
> 
> Is there a default function for this case in the reset framework?

No, the reset bindings assumes that you have a cell size of 1, and
it's the only case that's supported by the reset framework default
xlate.

I adressed the rest of your comments.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 04/19] clk: sunxi: Add TCON channel1 clock

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 725 bytes --]

On Fri, Apr 15, 2016 at 03:39:36PM -0700, Stephen Boyd wrote:
> On 03/23, Maxime Ripard wrote:
> > The TCON is a controller generating the timings to output videos signals,
> > acting like both a CRTC and an encoder.
> > 
> > It has two channels depending on the output, each channel being driven by
> > its own clock (and own clock controller).
> > 
> > Add a driver for the channel 1 clock.
> > 
> > Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> > Acked-by: Rob Herring <robh@kernel.org>
> > ---
> 
> Acked-by: Stephen Boyd <sboyd@codeaurora.org>

Applied, thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v3 01/19] clk: composite: Add unregister function

[Stephen Boyd]

On 04/19, Maxime Ripard wrote:
> 
> I have a bunch of other clock patches that need this, so I guess it
> would be easier if applied it directly with your acked-by, or if you
> could apply it and give a stable branch I can base my future PR on.

Ok. I pushed it to stable branch 'clk-composite-unregister' in
the clk.git repo. That way I can go ahead and delete this API
assuming I get around to converting all the composite users in
the next few days.

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project