From: Jaechul Lee <jcsing.lee@samsung.com>
To: Dmitry Torokhov <dmitry.torokhov@gmail.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Catalin Marinas <catalin.marinas@arm.com>,
Will Deacon <will.deacon@arm.com>, Kukjin Kim <kgene@kernel.org>,
Krzysztof Kozlowski <krzk@kernel.org>,
Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Jaechul Lee <jcsing.lee@samsung.com>,
Andi Shyti <andi.shyti@samsung.com>,
Chanwoo Choi <cw00.choi@samsung.com>,
beomho.seo@samsung.com, galaxyra@gmail.com,
linux-arm-kernel@lists.infradead.org,
linux-input@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-samsung-soc@vger.kernel.org
Subject: [PATCH v3 2/5] arm64: dts: exynos: make tm2 and tm2e independent from each other
Date: Fri, 06 Jan 2017 12:59:06 +0900 [thread overview]
Message-ID: <1483675149-32598-3-git-send-email-jcsing.lee@samsung.com> (raw)
In-Reply-To: <1483675149-32598-1-git-send-email-jcsing.lee@samsung.com>
From: Andi Shyti <andi.shyti@samsung.com>
Currently tm2e dts includes tm2 but there are some differences
between the two boards and tm2 has some properties that tm2e
doesn't have.
That's why it's important to keep the two dts files independent
and put all the commonalities in a tm2-common.dtsi file.
At the current status the only two differences between the two
dts files (besides the board name) are ldo31 and ldo38.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
---
.../boot/dts/exynos/exynos5433-tm2-common.dtsi | 1118 +++++++++++++++++++
arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 1153 +-------------------
arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts | 22 +-
3 files changed, 1163 insertions(+), 1130 deletions(-)
create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi
rewrite arch/arm64/boot/dts/exynos/exynos5433-tm2.dts (98%)
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi
new file mode 100644
index 0000000..c43f9a3
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi
@@ -0,0 +1,1118 @@
+/*
+ * SAMSUNG Exynos5433 TM2 board device tree source
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *
+ * Common device tree source file for Samsung's TM2 and TM2E boards
+ * which are based on Samsung Exynos5433 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include "exynos5433.dtsi"
+#include <dt-bindings/clock/samsung,s2mps11.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "Samsung TM2 board";
+ compatible = "samsung,tm2", "samsung,exynos5433";
+
+ aliases {
+ gsc0 = &gsc_0;
+ gsc1 = &gsc_1;
+ gsc2 = &gsc_2;
+ pinctrl0 = &pinctrl_alive;
+ pinctrl1 = &pinctrl_aud;
+ pinctrl2 = &pinctrl_cpif;
+ pinctrl3 = &pinctrl_ese;
+ pinctrl4 = &pinctrl_finger;
+ pinctrl5 = &pinctrl_fsys;
+ pinctrl6 = &pinctrl_imem;
+ pinctrl7 = &pinctrl_nfc;
+ pinctrl8 = &pinctrl_peric;
+ pinctrl9 = &pinctrl_touch;
+ serial0 = &serial_0;
+ serial1 = &serial_1;
+ serial2 = &serial_2;
+ serial3 = &serial_3;
+ spi0 = &spi_0;
+ spi1 = &spi_1;
+ spi2 = &spi_2;
+ spi3 = &spi_3;
+ spi4 = &spi_4;
+ mshc0 = &mshc_0;
+ mshc2 = &mshc_2;
+ };
+
+ chosen {
+ stdout-path = &serial_1;
+ };
+
+ memory@20000000 {
+ device_type = "memory";
+ reg = <0x0 0x20000000 0x0 0xc0000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ power-key {
+ gpios = <&gpa2 7 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ label = "power key";
+ debounce-interval = <10>;
+ };
+
+ volume-up-key {
+ gpios = <&gpa2 0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ label = "volume-up key";
+ debounce-interval = <10>;
+ };
+
+ volume-down-key {
+ gpios = <&gpa2 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ label = "volume-down key";
+ debounce-interval = <10>;
+ };
+
+ homepage-key {
+ gpios = <&gpa0 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_MENU>;
+ label = "homepage key";
+ debounce-interval = <10>;
+ };
+ };
+
+ i2c_max98504: i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ gpios = <&gpd0 1 GPIO_ACTIVE_HIGH /* SPK_AMP_SDA */
+ &gpd0 0 GPIO_ACTIVE_HIGH /* SPK_AMP_SCL */ >;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ max98504: max98504@31 {
+ compatible = "maxim,max98504";
+ reg = <0x31>;
+ maxim,rx-path = <1>;
+ maxim,tx-path = <1>;
+ maxim,tx-channel-mask = <3>;
+ maxim,tx-channel-source = <2>;
+ };
+ };
+
+ sound {
+ compatible = "samsung,tm2-audio";
+ audio-codec = <&wm5110>;
+ i2s-controller = <&i2s0>;
+ audio-amplifier = <&max98504>;
+ mic-bias-gpios = <&gpr3 2 GPIO_ACTIVE_HIGH>;
+ model = "wm5110";
+ samsung,audio-routing =
+ /* Headphone */
+ "HP", "HPOUT1L",
+ "HP", "HPOUT1R",
+
+ /* Speaker */
+ "SPK", "SPKOUT",
+ "SPKOUT", "HPOUT2L",
+ "SPKOUT", "HPOUT2R",
+
+ /* Receiver */
+ "RCV", "HPOUT3L",
+ "RCV", "HPOUT3R";
+ status = "okay";
+ };
+};
+
+&adc {
+ vdd-supply = <&ldo3_reg>;
+ status = "okay";
+
+ thermistor-ap {
+ compatible = "murata,ncp03wf104";
+ pullup-uv = <1800000>;
+ pullup-ohm = <100000>;
+ pulldown-ohm = <0>;
+ io-channels = <&adc 0>;
+ };
+
+ thermistor-battery {
+ compatible = "murata,ncp03wf104";
+ pullup-uv = <1800000>;
+ pullup-ohm = <100000>;
+ pulldown-ohm = <0>;
+ io-channels = <&adc 1>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ thermistor-charger {
+ compatible = "murata,ncp03wf104";
+ pullup-uv = <1800000>;
+ pullup-ohm = <100000>;
+ pulldown-ohm = <0>;
+ io-channels = <&adc 2>;
+ };
+};
+
+&bus_g2d_400 {
+ devfreq-events = <&ppmu_event0_d0_general>, <&ppmu_event0_d1_general>;
+ vdd-supply = <&buck4_reg>;
+ exynos,saturation-ratio = <10>;
+ status = "okay";
+};
+
+&bus_g2d_266 {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_gscl {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_hevc {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_jpeg {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_mfc {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_mscl {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_noc0 {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_noc1 {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_noc2 {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&cmu_aud {
+ assigned-clocks = <&cmu_aud CLK_MOUT_AUD_PLL_USER>;
+ assigned-clock-parents = <&cmu_top CLK_FOUT_AUD_PLL>;
+};
+
+&cmu_fsys {
+ assigned-clocks = <&cmu_top CLK_MOUT_SCLK_USBDRD30>,
+ <&cmu_top CLK_MOUT_SCLK_USBHOST30>,
+ <&cmu_fsys CLK_MOUT_SCLK_USBDRD30_USER>,
+ <&cmu_fsys CLK_MOUT_SCLK_USBHOST30_USER>,
+ <&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_USER>,
+ <&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_USER>,
+ <&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_USER>,
+ <&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_USER>,
+ <&cmu_top CLK_DIV_SCLK_USBDRD30>,
+ <&cmu_top CLK_DIV_SCLK_USBHOST30>;
+ assigned-clock-parents = <&cmu_top CLK_MOUT_BUS_PLL_USER>,
+ <&cmu_top CLK_MOUT_BUS_PLL_USER>,
+ <&cmu_top CLK_SCLK_USBDRD30_FSYS>,
+ <&cmu_top CLK_SCLK_USBHOST30_FSYS>,
+ <&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_PHY>,
+ <&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_PHY>,
+ <&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_PHY>,
+ <&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_PHY>;
+ assigned-clock-rates = <0>, <0>, <0>, <0>, <0>, <0>, <0>, <0>,
+ <66700000>, <66700000>;
+};
+
+&cmu_gscl {
+ assigned-clocks = <&cmu_gscl CLK_MOUT_ACLK_GSCL_111_USER>,
+ <&cmu_gscl CLK_MOUT_ACLK_GSCL_333_USER>;
+ assigned-clock-parents = <&cmu_top CLK_ACLK_GSCL_111>,
+ <&cmu_top CLK_ACLK_GSCL_333>;
+};
+
+&cmu_mfc {
+ assigned-clocks = <&cmu_mfc CLK_MOUT_ACLK_MFC_400_USER>;
+ assigned-clock-parents = <&cmu_top CLK_ACLK_MFC_400>;
+};
+
+&cmu_mscl {
+ assigned-clocks = <&cmu_mscl CLK_MOUT_ACLK_MSCL_400_USER>,
+ <&cmu_mscl CLK_MOUT_SCLK_JPEG_USER>,
+ <&cmu_mscl CLK_MOUT_SCLK_JPEG>,
+ <&cmu_top CLK_MOUT_SCLK_JPEG_A>;
+ assigned-clock-parents = <&cmu_top CLK_ACLK_MSCL_400>,
+ <&cmu_top CLK_SCLK_JPEG_MSCL>,
+ <&cmu_mscl CLK_MOUT_SCLK_JPEG_USER>,
+ <&cmu_top CLK_MOUT_BUS_PLL_USER>;
+};
+
+&cpu0 {
+ cpu-supply = <&buck3_reg>;
+};
+
+&cpu4 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&decon {
+ status = "okay";
+
+ i80-if-timings {
+ };
+};
+
+&dsi {
+ status = "okay";
+ vddcore-supply = <&ldo6_reg>;
+ vddio-supply = <&ldo7_reg>;
+ samsung,pll-clock-frequency = <24000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&te_irq>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+
+ dsi_out: endpoint {
+ samsung,burst-clock-frequency = <512000000>;
+ samsung,esc-clock-frequency = <16000000>;
+ };
+ };
+ };
+};
+
+&hsi2c_0 {
+ status = "okay";
+ clock-frequency = <2500000>;
+
+ s2mps13-pmic@66 {
+ compatible = "samsung,s2mps13-pmic";
+ interrupt-parent = <&gpa0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
+ reg = <0x66>;
+ samsung,s2mps11-wrstbi-ground;
+
+ s2mps13_osc: clocks {
+ compatible = "samsung,s2mps13-clk";
+ #clock-cells = <1>;
+ clock-output-names = "s2mps13_ap", "s2mps13_cp",
+ "s2mps13_bt";
+ };
+
+ regulators: regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE_0.9V_AP";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VDDQ_MMC2_2.8V_AP";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VDD1_E_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VDD10_MIF_PLL_1.0V_AP";
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "VDD10_DPLL_1.0V_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "VDD10_MIPI2L_1.0V_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD18_MIPI2L_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "VDD18_LLI_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "VDD18_ABB_ETC_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "VDD33_USB30_3.0V_AP";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD_INT_M_1.0V_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "VDD_KFC_M_1.1V_AP";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "VDD_G3D_M_0.95V_AP";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <950000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "VDDQ_M1_LDO_1.2V_AP";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "VDDQ_M2_LDO_1.2V_AP";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "VDDQ_EFUSE";
+ regulator-min-microvolt = <1400000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-always-on;
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "V_TFLASH_2.8V_AP";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo18_reg: LDO18 {
+ regulator-name = "V_CODEC_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo19_reg: LDO19 {
+ regulator-name = "VDDA_1.8V_COMP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo20_reg: LDO20 {
+ regulator-name = "VCC_2.8V_AP";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo21_reg: LDO21 {
+ regulator-name = "VT_CAM_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo22_reg: LDO22 {
+ regulator-name = "CAM_IO_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo23_reg: LDO23 {
+ regulator-name = "CAM_SEN_CORE_1.05V_AP";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ ldo24_reg: LDO24 {
+ regulator-name = "VT_CAM_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo25_reg: LDO25 {
+ regulator-name = "UNUSED_LDO25";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-off;
+ };
+
+ ldo26_reg: LDO26 {
+ regulator-name = "CAM_AF_2.8V_AP";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo27_reg: LDO27 {
+ regulator-name = "VCC_3.0V_LCD_AP";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ ldo28_reg: LDO28 {
+ regulator-name = "VCC_1.8V_LCD_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo29_reg: LDO29 {
+ regulator-name = "VT_CAM_2.8V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ ldo30_reg: LDO30 {
+ regulator-name = "TSP_AVDD_3.3V_AP";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ /*
+ * LDO31 differs from target to target,
+ * its definition is in the .dts
+ */
+
+ ldo32_reg: LDO32 {
+ regulator-name = "VTOUCH_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo33_reg: LDO33 {
+ regulator-name = "VTOUCH_LED_3.3V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <12500>;
+ };
+
+ ldo34_reg: LDO34 {
+ regulator-name = "VCC_1.8V_MHL_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <2100000>;
+ };
+
+ ldo35_reg: LDO35 {
+ regulator-name = "OIS_VM_2.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo36_reg: LDO36 {
+ regulator-name = "VSIL_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ ldo37_reg: LDO37 {
+ regulator-name = "VF_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ /*
+ * LDO38 differs from target to target,
+ * its definition is in the .dts
+ */
+
+ ldo39_reg: LDO39 {
+ regulator-name = "V_HRM_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo40_reg: LDO40 {
+ regulator-name = "V_HRM_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "VDD_MIF_0.9V_AP";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "VDD_EGL_1.0V_AP";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "VDD_KFC_1.0V_AP";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "VDD_INT_0.95V_AP";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "VDD_DISP_CAM0_0.9V_AP";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "VDD_G3D_0.9V_AP";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "VDD_MEM1_1.2V_AP";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "VDD_LLDO_1.35V_AP";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ buck9_reg: BUCK9 {
+ regulator-name = "VDD_MLDO_2.0V_AP";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ buck10_reg: BUCK10 {
+ regulator-name = "vdd_mem2";
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&hsi2c_8 {
+ status = "okay";
+
+ max77843@66 {
+ compatible = "maxim,max77843";
+ interrupt-parent = <&gpa1>;
+ interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+ reg = <0x66>;
+
+ muic: max77843-muic {
+ compatible = "maxim,max77843-muic";
+ };
+
+ regulators {
+ compatible = "maxim,max77843-regulator";
+ safeout1_reg: SAFEOUT1 {
+ regulator-name = "SAFEOUT1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <4950000>;
+ };
+
+ safeout2_reg: SAFEOUT2 {
+ regulator-name = "SAFEOUT2";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <4950000>;
+ };
+
+ charger_reg: CHARGER {
+ regulator-name = "CHARGER";
+ regulator-min-microamp = <100000>;
+ regulator-max-microamp = <3150000>;
+ };
+ };
+
+ haptic: max77843-haptic {
+ compatible = "maxim,max77843-haptic";
+ haptic-supply = <&ldo38_reg>;
+ pwms = <&pwm 0 33670 0>;
+ pwm-names = "haptic";
+ };
+ };
+};
+
+&i2s0 {
+ status = "okay";
+};
+
+&mshc_0 {
+ status = "okay";
+ num-slots = <1>;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ cap-mmc-highspeed;
+ non-removable;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <0 4>;
+ samsung,dw-mshc-ddr-timing = <0 2>;
+ samsung,dw-mshc-hs400-timing = <0 3>;
+ samsung,read-strobe-delay = <90>;
+ fifo-depth = <0x80>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_qrdy &sd0_bus1 &sd0_bus4
+ &sd0_bus8 &sd0_rdqs>;
+ bus-width = <8>;
+ assigned-clocks = <&cmu_top CLK_SCLK_MMC0_FSYS>;
+ assigned-clock-rates = <800000000>;
+};
+
+&mshc_2 {
+ status = "okay";
+ num-slots = <1>;
+ cap-sd-highspeed;
+ disable-wp;
+ cd-gpios = <&gpa2 4 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <0 4>;
+ samsung,dw-mshc-ddr-timing = <0 2>;
+ fifo-depth = <0x80>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus1 &sd2_bus4>;
+ bus-width = <4>;
+};
+
+&ppmu_d0_general {
+ status = "okay";
+ events {
+ ppmu_event0_d0_general: ppmu-event0-d0-general {
+ event-name = "ppmu-event0-d0-general";
+ };
+ };
+};
+
+&ppmu_d1_general {
+ status = "okay";
+ events {
+ ppmu_event0_d1_general: ppmu-event0-d1-general {
+ event-name = "ppmu-event0-d1-general";
+ };
+ };
+};
+
+&pinctrl_alive {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_alive>;
+
+ initial_alive: initial-state {
+ PIN(INPUT, gpa0-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpa0-1, NONE, FAST_SR1);
+ PIN(INPUT, gpa0-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpa0-3, NONE, FAST_SR1);
+ PIN(INPUT, gpa0-4, NONE, FAST_SR1);
+ PIN(INPUT, gpa0-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpa0-6, NONE, FAST_SR1);
+ PIN(INPUT, gpa0-7, NONE, FAST_SR1);
+
+ PIN(INPUT, gpa1-0, UP, FAST_SR1);
+ PIN(INPUT, gpa1-1, NONE, FAST_SR1);
+ PIN(INPUT, gpa1-2, NONE, FAST_SR1);
+ PIN(INPUT, gpa1-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpa1-4, DOWN, FAST_SR1);
+ PIN(INPUT, gpa1-5, NONE, FAST_SR1);
+ PIN(INPUT, gpa1-6, NONE, FAST_SR1);
+ PIN(INPUT, gpa1-7, NONE, FAST_SR1);
+
+ PIN(INPUT, gpa2-0, NONE, FAST_SR1);
+ PIN(INPUT, gpa2-1, NONE, FAST_SR1);
+ PIN(INPUT, gpa2-2, NONE, FAST_SR1);
+ PIN(INPUT, gpa2-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpa2-4, NONE, FAST_SR1);
+ PIN(INPUT, gpa2-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpa2-6, DOWN, FAST_SR1);
+ PIN(INPUT, gpa2-7, NONE, FAST_SR1);
+
+ PIN(INPUT, gpa3-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpa3-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpa3-2, NONE, FAST_SR1);
+ PIN(INPUT, gpa3-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpa3-4, NONE, FAST_SR1);
+ PIN(INPUT, gpa3-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpa3-6, DOWN, FAST_SR1);
+ PIN(INPUT, gpa3-7, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpf1-0, NONE, FAST_SR1);
+ PIN(INPUT, gpf1-1, NONE, FAST_SR1);
+ PIN(INPUT, gpf1-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpf1-4, UP, FAST_SR1);
+ PIN(OUTPUT, gpf1-5, NONE, FAST_SR1);
+ PIN(INPUT, gpf1-6, DOWN, FAST_SR1);
+ PIN(INPUT, gpf1-7, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpf2-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpf2-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpf2-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpf2-3, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpf3-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpf3-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpf3-2, NONE, FAST_SR1);
+ PIN(INPUT, gpf3-3, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpf4-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-4, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-6, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-7, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpf5-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpf5-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpf5-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpf5-3, DOWN, FAST_SR1);
+ PIN(OUTPUT, gpf5-4, NONE, FAST_SR1);
+ PIN(INPUT, gpf5-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpf5-6, DOWN, FAST_SR1);
+ PIN(INPUT, gpf5-7, DOWN, FAST_SR1);
+ };
+
+ te_irq: te_irq {
+ samsung,pins = "gpf1-3";
+ samsung,pin-function = <0xf>;
+ };
+};
+
+&pinctrl_cpif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_cpif>;
+
+ initial_cpif: initial-state {
+ PIN(INPUT, gpv6-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpv6-1, DOWN, FAST_SR1);
+ };
+};
+
+&pinctrl_ese {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_ese>;
+
+ initial_ese: initial-state {
+ PIN(INPUT, gpj2-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpj2-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpj2-2, DOWN, FAST_SR1);
+ };
+};
+
+&pinctrl_fsys {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_fsys>;
+
+ initial_fsys: initial-state {
+ PIN(INPUT, gpr3-0, NONE, FAST_SR1);
+ PIN(INPUT, gpr3-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpr3-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpr3-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpr3-7, NONE, FAST_SR1);
+ };
+};
+
+&pinctrl_imem {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_imem>;
+
+ initial_imem: initial-state {
+ PIN(INPUT, gpf0-0, UP, FAST_SR1);
+ PIN(INPUT, gpf0-1, UP, FAST_SR1);
+ PIN(INPUT, gpf0-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpf0-3, UP, FAST_SR1);
+ PIN(INPUT, gpf0-4, DOWN, FAST_SR1);
+ PIN(INPUT, gpf0-5, NONE, FAST_SR1);
+ PIN(INPUT, gpf0-6, DOWN, FAST_SR1);
+ PIN(INPUT, gpf0-7, UP, FAST_SR1);
+ };
+};
+
+&pinctrl_nfc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_nfc>;
+
+ initial_nfc: initial-state {
+ PIN(INPUT, gpj0-2, DOWN, FAST_SR1);
+ };
+};
+
+&pinctrl_peric {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_peric>;
+
+ initial_peric: initial-state {
+ PIN(INPUT, gpv7-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpv7-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpv7-2, NONE, FAST_SR1);
+ PIN(INPUT, gpv7-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpv7-4, DOWN, FAST_SR1);
+ PIN(INPUT, gpv7-5, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpb0-4, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpc0-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpc0-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpc0-7, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpc1-1, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpc3-4, NONE, FAST_SR1);
+ PIN(INPUT, gpc3-5, NONE, FAST_SR1);
+ PIN(INPUT, gpc3-6, NONE, FAST_SR1);
+ PIN(INPUT, gpc3-7, NONE, FAST_SR1);
+
+ PIN(OUTPUT, gpg0-0, NONE, FAST_SR1);
+ PIN(2, gpg0-1, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpd2-5, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpd4-0, NONE, FAST_SR1);
+ PIN(INPUT, gpd4-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpd4-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpd4-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpd4-4, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpd6-3, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpd8-1, UP, FAST_SR1);
+
+ PIN(INPUT, gpg1-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpg1-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpg1-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpg1-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpg1-4, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpg2-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpg2-1, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpg3-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpg3-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpg3-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpg3-7, DOWN, FAST_SR1);
+ };
+};
+
+&pinctrl_touch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_touch>;
+
+ initial_touch: initial-state {
+ PIN(INPUT, gpj1-2, DOWN, FAST_SR1);
+ };
+};
+
+&pwm {
+ pinctrl-0 = <&pwm0_out>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&mic {
+ status = "okay";
+
+ i80-if-timings {
+ };
+};
+
+&pmu_system_controller {
+ assigned-clocks = <&pmu_system_controller 0>;
+ assigned-clock-parents = <&xxti>;
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&spi_1 {
+ cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ wm5110: wm5110-codec@0 {
+ compatible = "wlf,wm5110";
+ reg = <0x0>;
+ spi-max-frequency = <20000000>;
+ interrupt-parent = <&gpa0>;
+ interrupts = <4 IRQ_TYPE_NONE>;
+ clocks = <&pmu_system_controller 0>,
+ <&s2mps13_osc S2MPS11_CLK_BT>;
+ clock-names = "mclk1", "mclk2";
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ wlf,micd-detect-debounce = <300>;
+ wlf,micd-bias-start-time = <0x1>;
+ wlf,micd-rate = <0x7>;
+ wlf,micd-dbtime = <0x1>;
+ wlf,micd-force-micbias;
+ wlf,micd-configs = <0x0 1 0>;
+ wlf,hpdet-channel = <1>;
+ wlf,gpsw = <0x1>;
+ wlf,inmode = <2 0 2 0>;
+
+ wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
+ wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
+
+ /* core supplies */
+ AVDD-supply = <&ldo18_reg>;
+ DBVDD1-supply = <&ldo18_reg>;
+ CPVDD-supply = <&ldo18_reg>;
+ DBVDD2-supply = <&ldo18_reg>;
+ DBVDD3-supply = <&ldo18_reg>;
+
+ controller-data {
+ samsung,spi-feedback-delay = <0>;
+ };
+ };
+};
+
+&timer {
+ clock-frequency = <24000000>;
+};
+
+&tmu_atlas0 {
+ vtmu-supply = <&ldo3_reg>;
+ status = "okay";
+};
+
+&tmu_apollo {
+ vtmu-supply = <&ldo3_reg>;
+ status = "okay";
+};
+
+&tmu_g3d {
+ vtmu-supply = <&ldo3_reg>;
+ status = "okay";
+};
+
+&usbdrd30 {
+ vdd33-supply = <&ldo10_reg>;
+ vdd10-supply = <&ldo6_reg>;
+ status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+ dr_mode = "otg";
+};
+
+&usbdrd30_phy {
+ vbus-supply = <&safeout1_reg>;
+ status = "okay";
+};
+
+&xxti {
+ clock-frequency = <24000000>;
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
dissimilarity index 98%
index e8971f4..d30b45a 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
@@ -1,1120 +1,33 @@
-/*
- * SAMSUNG Exynos5433 TM2 board device tree source
- *
- * Copyright (c) 2016 Samsung Electronics Co., Ltd.
- *
- * Device tree source file for Samsung's TM2 board which is based on
- * Samsung Exynos5433 SoC.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-/dts-v1/;
-#include "exynos5433.dtsi"
-#include <dt-bindings/clock/samsung,s2mps11.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-
-/ {
- model = "Samsung TM2 board";
- compatible = "samsung,tm2", "samsung,exynos5433";
-
- aliases {
- gsc0 = &gsc_0;
- gsc1 = &gsc_1;
- gsc2 = &gsc_2;
- pinctrl0 = &pinctrl_alive;
- pinctrl1 = &pinctrl_aud;
- pinctrl2 = &pinctrl_cpif;
- pinctrl3 = &pinctrl_ese;
- pinctrl4 = &pinctrl_finger;
- pinctrl5 = &pinctrl_fsys;
- pinctrl6 = &pinctrl_imem;
- pinctrl7 = &pinctrl_nfc;
- pinctrl8 = &pinctrl_peric;
- pinctrl9 = &pinctrl_touch;
- serial0 = &serial_0;
- serial1 = &serial_1;
- serial2 = &serial_2;
- serial3 = &serial_3;
- spi0 = &spi_0;
- spi1 = &spi_1;
- spi2 = &spi_2;
- spi3 = &spi_3;
- spi4 = &spi_4;
- mshc0 = &mshc_0;
- mshc2 = &mshc_2;
- };
-
- chosen {
- stdout-path = &serial_1;
- };
-
- memory@20000000 {
- device_type = "memory";
- reg = <0x0 0x20000000 0x0 0xc0000000>;
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- power-key {
- gpios = <&gpa2 7 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- label = "power key";
- debounce-interval = <10>;
- };
-
- volume-up-key {
- gpios = <&gpa2 0 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_VOLUMEUP>;
- label = "volume-up key";
- debounce-interval = <10>;
- };
-
- volume-down-key {
- gpios = <&gpa2 1 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_VOLUMEDOWN>;
- label = "volume-down key";
- debounce-interval = <10>;
- };
-
- homepage-key {
- gpios = <&gpa0 3 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_MENU>;
- label = "homepage key";
- debounce-interval = <10>;
- };
- };
-
- i2c_max98504: i2c-gpio-0 {
- compatible = "i2c-gpio";
- gpios = <&gpd0 1 GPIO_ACTIVE_HIGH /* SPK_AMP_SDA */
- &gpd0 0 GPIO_ACTIVE_HIGH /* SPK_AMP_SCL */ >;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- max98504: max98504@31 {
- compatible = "maxim,max98504";
- reg = <0x31>;
- maxim,rx-path = <1>;
- maxim,tx-path = <1>;
- maxim,tx-channel-mask = <3>;
- maxim,tx-channel-source = <2>;
- };
- };
-
- sound {
- compatible = "samsung,tm2-audio";
- audio-codec = <&wm5110>;
- i2s-controller = <&i2s0>;
- audio-amplifier = <&max98504>;
- mic-bias-gpios = <&gpr3 2 GPIO_ACTIVE_HIGH>;
- model = "wm5110";
- samsung,audio-routing =
- /* Headphone */
- "HP", "HPOUT1L",
- "HP", "HPOUT1R",
-
- /* Speaker */
- "SPK", "SPKOUT",
- "SPKOUT", "HPOUT2L",
- "SPKOUT", "HPOUT2R",
-
- /* Receiver */
- "RCV", "HPOUT3L",
- "RCV", "HPOUT3R";
- status = "okay";
- };
-};
-
-&adc {
- vdd-supply = <&ldo3_reg>;
- status = "okay";
-
- thermistor-ap {
- compatible = "murata,ncp03wf104";
- pullup-uv = <1800000>;
- pullup-ohm = <100000>;
- pulldown-ohm = <0>;
- io-channels = <&adc 0>;
- };
-
- thermistor-battery {
- compatible = "murata,ncp03wf104";
- pullup-uv = <1800000>;
- pullup-ohm = <100000>;
- pulldown-ohm = <0>;
- io-channels = <&adc 1>;
- #thermal-sensor-cells = <0>;
- };
-
- thermistor-charger {
- compatible = "murata,ncp03wf104";
- pullup-uv = <1800000>;
- pullup-ohm = <100000>;
- pulldown-ohm = <0>;
- io-channels = <&adc 2>;
- };
-};
-
-&bus_g2d_400 {
- devfreq-events = <&ppmu_event0_d0_general>, <&ppmu_event0_d1_general>;
- vdd-supply = <&buck4_reg>;
- exynos,saturation-ratio = <10>;
- status = "okay";
-};
-
-&bus_g2d_266 {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_gscl {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_hevc {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_jpeg {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_mfc {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_mscl {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_noc0 {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_noc1 {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_noc2 {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&cmu_aud {
- assigned-clocks = <&cmu_aud CLK_MOUT_AUD_PLL_USER>;
- assigned-clock-parents = <&cmu_top CLK_FOUT_AUD_PLL>;
-};
-
-&cmu_fsys {
- assigned-clocks = <&cmu_top CLK_MOUT_SCLK_USBDRD30>,
- <&cmu_top CLK_MOUT_SCLK_USBHOST30>,
- <&cmu_fsys CLK_MOUT_SCLK_USBDRD30_USER>,
- <&cmu_fsys CLK_MOUT_SCLK_USBHOST30_USER>,
- <&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_USER>,
- <&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_USER>,
- <&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_USER>,
- <&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_USER>,
- <&cmu_top CLK_DIV_SCLK_USBDRD30>,
- <&cmu_top CLK_DIV_SCLK_USBHOST30>;
- assigned-clock-parents = <&cmu_top CLK_MOUT_BUS_PLL_USER>,
- <&cmu_top CLK_MOUT_BUS_PLL_USER>,
- <&cmu_top CLK_SCLK_USBDRD30_FSYS>,
- <&cmu_top CLK_SCLK_USBHOST30_FSYS>,
- <&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_PHY>,
- <&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_PHY>,
- <&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_PHY>,
- <&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_PHY>;
- assigned-clock-rates = <0>, <0>, <0>, <0>, <0>, <0>, <0>, <0>,
- <66700000>, <66700000>;
-};
-
-&cmu_gscl {
- assigned-clocks = <&cmu_gscl CLK_MOUT_ACLK_GSCL_111_USER>,
- <&cmu_gscl CLK_MOUT_ACLK_GSCL_333_USER>;
- assigned-clock-parents = <&cmu_top CLK_ACLK_GSCL_111>,
- <&cmu_top CLK_ACLK_GSCL_333>;
-};
-
-&cmu_mfc {
- assigned-clocks = <&cmu_mfc CLK_MOUT_ACLK_MFC_400_USER>;
- assigned-clock-parents = <&cmu_top CLK_ACLK_MFC_400>;
-};
-
-&cmu_mscl {
- assigned-clocks = <&cmu_mscl CLK_MOUT_ACLK_MSCL_400_USER>,
- <&cmu_mscl CLK_MOUT_SCLK_JPEG_USER>,
- <&cmu_mscl CLK_MOUT_SCLK_JPEG>,
- <&cmu_top CLK_MOUT_SCLK_JPEG_A>;
- assigned-clock-parents = <&cmu_top CLK_ACLK_MSCL_400>,
- <&cmu_top CLK_SCLK_JPEG_MSCL>,
- <&cmu_mscl CLK_MOUT_SCLK_JPEG_USER>,
- <&cmu_top CLK_MOUT_BUS_PLL_USER>;
-};
-
-&cpu0 {
- cpu-supply = <&buck3_reg>;
-};
-
-&cpu4 {
- cpu-supply = <&buck2_reg>;
-};
-
-&decon {
- status = "okay";
-
- i80-if-timings {
- };
-};
-
-&dsi {
- status = "okay";
- vddcore-supply = <&ldo6_reg>;
- vddio-supply = <&ldo7_reg>;
- samsung,pll-clock-frequency = <24000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&te_irq>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@1 {
- reg = <1>;
-
- dsi_out: endpoint {
- samsung,burst-clock-frequency = <512000000>;
- samsung,esc-clock-frequency = <16000000>;
- };
- };
- };
-};
-
-&hsi2c_0 {
- status = "okay";
- clock-frequency = <2500000>;
-
- s2mps13-pmic@66 {
- compatible = "samsung,s2mps13-pmic";
- interrupt-parent = <&gpa0>;
- interrupts = <7 IRQ_TYPE_NONE>;
- reg = <0x66>;
- samsung,s2mps11-wrstbi-ground;
-
- s2mps13_osc: clocks {
- compatible = "samsung,s2mps13-clk";
- #clock-cells = <1>;
- clock-output-names = "s2mps13_ap", "s2mps13_cp",
- "s2mps13_bt";
- };
-
- regulators {
- ldo1_reg: LDO1 {
- regulator-name = "VDD_ALIVE_0.9V_AP";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <900000>;
- regulator-always-on;
- };
-
- ldo2_reg: LDO2 {
- regulator-name = "VDDQ_MMC2_2.8V_AP";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo3_reg: LDO3 {
- regulator-name = "VDD1_E_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo4_reg: LDO4 {
- regulator-name = "VDD10_MIF_PLL_1.0V_AP";
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo5_reg: LDO5 {
- regulator-name = "VDD10_DPLL_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo6_reg: LDO6 {
- regulator-name = "VDD10_MIPI2L_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo7_reg: LDO7 {
- regulator-name = "VDD18_MIPI2L_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo8_reg: LDO8 {
- regulator-name = "VDD18_LLI_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo9_reg: LDO9 {
- regulator-name = "VDD18_ABB_ETC_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo10_reg: LDO10 {
- regulator-name = "VDD33_USB30_3.0V_AP";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo11_reg: LDO11 {
- regulator-name = "VDD_INT_M_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo12_reg: LDO12 {
- regulator-name = "VDD_KFC_M_1.1V_AP";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- };
-
- ldo13_reg: LDO13 {
- regulator-name = "VDD_G3D_M_0.95V_AP";
- regulator-min-microvolt = <950000>;
- regulator-max-microvolt = <950000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo14_reg: LDO14 {
- regulator-name = "VDDQ_M1_LDO_1.2V_AP";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo15_reg: LDO15 {
- regulator-name = "VDDQ_M2_LDO_1.2V_AP";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo16_reg: LDO16 {
- regulator-name = "VDDQ_EFUSE";
- regulator-min-microvolt = <1400000>;
- regulator-max-microvolt = <3400000>;
- regulator-always-on;
- };
-
- ldo17_reg: LDO17 {
- regulator-name = "V_TFLASH_2.8V_AP";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo18_reg: LDO18 {
- regulator-name = "V_CODEC_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo19_reg: LDO19 {
- regulator-name = "VDDA_1.8V_COMP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo20_reg: LDO20 {
- regulator-name = "VCC_2.8V_AP";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- ldo21_reg: LDO21 {
- regulator-name = "VT_CAM_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo22_reg: LDO22 {
- regulator-name = "CAM_IO_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo23_reg: LDO23 {
- regulator-name = "CAM_SEN_CORE_1.05V_AP";
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- };
-
- ldo24_reg: LDO24 {
- regulator-name = "VT_CAM_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- ldo25_reg: LDO25 {
- regulator-name = "UNUSED_LDO25";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-off;
- };
-
- ldo26_reg: LDO26 {
- regulator-name = "CAM_AF_2.8V_AP";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo27_reg: LDO27 {
- regulator-name = "VCC_3.0V_LCD_AP";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- ldo28_reg: LDO28 {
- regulator-name = "VCC_1.8V_LCD_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo29_reg: LDO29 {
- regulator-name = "VT_CAM_2.8V";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- ldo30_reg: LDO30 {
- regulator-name = "TSP_AVDD_3.3V_AP";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo31_reg: LDO31 {
- regulator-name = "TSP_VDD_1.85V_AP";
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <1850000>;
- };
-
- ldo32_reg: LDO32 {
- regulator-name = "VTOUCH_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo33_reg: LDO33 {
- regulator-name = "VTOUCH_LED_3.3V";
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <3300000>;
- regulator-ramp-delay = <12500>;
- };
-
- ldo34_reg: LDO34 {
- regulator-name = "VCC_1.8V_MHL_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <2100000>;
- };
-
- ldo35_reg: LDO35 {
- regulator-name = "OIS_VM_2.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo36_reg: LDO36 {
- regulator-name = "VSIL_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
-
- ldo37_reg: LDO37 {
- regulator-name = "VF_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo38_reg: LDO38 {
- regulator-name = "VCC_3.0V_MOTOR_AP";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- ldo39_reg: LDO39 {
- regulator-name = "V_HRM_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo40_reg: LDO40 {
- regulator-name = "V_HRM_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- buck1_reg: BUCK1 {
- regulator-name = "VDD_MIF_0.9V_AP";
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck2_reg: BUCK2 {
- regulator-name = "VDD_EGL_1.0V_AP";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck3_reg: BUCK3 {
- regulator-name = "VDD_KFC_1.0V_AP";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck4_reg: BUCK4 {
- regulator-name = "VDD_INT_0.95V_AP";
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck5_reg: BUCK5 {
- regulator-name = "VDD_DISP_CAM0_0.9V_AP";
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck6_reg: BUCK6 {
- regulator-name = "VDD_G3D_0.9V_AP";
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck7_reg: BUCK7 {
- regulator-name = "VDD_MEM1_1.2V_AP";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- buck8_reg: BUCK8 {
- regulator-name = "VDD_LLDO_1.35V_AP";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- buck9_reg: BUCK9 {
- regulator-name = "VDD_MLDO_2.0V_AP";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- buck10_reg: BUCK10 {
- regulator-name = "vdd_mem2";
- regulator-min-microvolt = <550000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- };
- };
- };
-};
-
-&hsi2c_8 {
- status = "okay";
-
- max77843@66 {
- compatible = "maxim,max77843";
- interrupt-parent = <&gpa1>;
- interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
- reg = <0x66>;
-
- muic: max77843-muic {
- compatible = "maxim,max77843-muic";
- };
-
- regulators {
- compatible = "maxim,max77843-regulator";
- safeout1_reg: SAFEOUT1 {
- regulator-name = "SAFEOUT1";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <4950000>;
- };
-
- safeout2_reg: SAFEOUT2 {
- regulator-name = "SAFEOUT2";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <4950000>;
- };
-
- charger_reg: CHARGER {
- regulator-name = "CHARGER";
- regulator-min-microamp = <100000>;
- regulator-max-microamp = <3150000>;
- };
- };
-
- haptic: max77843-haptic {
- compatible = "maxim,max77843-haptic";
- haptic-supply = <&ldo38_reg>;
- pwms = <&pwm 0 33670 0>;
- pwm-names = "haptic";
- };
- };
-};
-
-&i2s0 {
- status = "okay";
-};
-
-&mshc_0 {
- status = "okay";
- num-slots = <1>;
- mmc-hs200-1_8v;
- mmc-hs400-1_8v;
- cap-mmc-highspeed;
- non-removable;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <0 4>;
- samsung,dw-mshc-ddr-timing = <0 2>;
- samsung,dw-mshc-hs400-timing = <0 3>;
- samsung,read-strobe-delay = <90>;
- fifo-depth = <0x80>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_qrdy &sd0_bus1 &sd0_bus4
- &sd0_bus8 &sd0_rdqs>;
- bus-width = <8>;
- assigned-clocks = <&cmu_top CLK_SCLK_MMC0_FSYS>;
- assigned-clock-rates = <800000000>;
-};
-
-&mshc_2 {
- status = "okay";
- num-slots = <1>;
- cap-sd-highspeed;
- disable-wp;
- cd-gpios = <&gpa2 4 GPIO_ACTIVE_HIGH>;
- cd-inverted;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <0 4>;
- samsung,dw-mshc-ddr-timing = <0 2>;
- fifo-depth = <0x80>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus1 &sd2_bus4>;
- bus-width = <4>;
-};
-
-&ppmu_d0_general {
- status = "okay";
- events {
- ppmu_event0_d0_general: ppmu-event0-d0-general {
- event-name = "ppmu-event0-d0-general";
- };
- };
-};
-
-&ppmu_d1_general {
- status = "okay";
- events {
- ppmu_event0_d1_general: ppmu-event0-d1-general {
- event-name = "ppmu-event0-d1-general";
- };
- };
-};
-
-&pinctrl_alive {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_alive>;
-
- initial_alive: initial-state {
- PIN(INPUT, gpa0-0, DOWN, FAST_SR1);
- PIN(INPUT, gpa0-1, NONE, FAST_SR1);
- PIN(INPUT, gpa0-2, DOWN, FAST_SR1);
- PIN(INPUT, gpa0-3, NONE, FAST_SR1);
- PIN(INPUT, gpa0-4, NONE, FAST_SR1);
- PIN(INPUT, gpa0-5, DOWN, FAST_SR1);
- PIN(INPUT, gpa0-6, NONE, FAST_SR1);
- PIN(INPUT, gpa0-7, NONE, FAST_SR1);
-
- PIN(INPUT, gpa1-0, UP, FAST_SR1);
- PIN(INPUT, gpa1-1, NONE, FAST_SR1);
- PIN(INPUT, gpa1-2, NONE, FAST_SR1);
- PIN(INPUT, gpa1-3, DOWN, FAST_SR1);
- PIN(INPUT, gpa1-4, DOWN, FAST_SR1);
- PIN(INPUT, gpa1-5, NONE, FAST_SR1);
- PIN(INPUT, gpa1-6, NONE, FAST_SR1);
- PIN(INPUT, gpa1-7, NONE, FAST_SR1);
-
- PIN(INPUT, gpa2-0, NONE, FAST_SR1);
- PIN(INPUT, gpa2-1, NONE, FAST_SR1);
- PIN(INPUT, gpa2-2, NONE, FAST_SR1);
- PIN(INPUT, gpa2-3, DOWN, FAST_SR1);
- PIN(INPUT, gpa2-4, NONE, FAST_SR1);
- PIN(INPUT, gpa2-5, DOWN, FAST_SR1);
- PIN(INPUT, gpa2-6, DOWN, FAST_SR1);
- PIN(INPUT, gpa2-7, NONE, FAST_SR1);
-
- PIN(INPUT, gpa3-0, DOWN, FAST_SR1);
- PIN(INPUT, gpa3-1, DOWN, FAST_SR1);
- PIN(INPUT, gpa3-2, NONE, FAST_SR1);
- PIN(INPUT, gpa3-3, DOWN, FAST_SR1);
- PIN(INPUT, gpa3-4, NONE, FAST_SR1);
- PIN(INPUT, gpa3-5, DOWN, FAST_SR1);
- PIN(INPUT, gpa3-6, DOWN, FAST_SR1);
- PIN(INPUT, gpa3-7, DOWN, FAST_SR1);
-
- PIN(INPUT, gpf1-0, NONE, FAST_SR1);
- PIN(INPUT, gpf1-1, NONE, FAST_SR1);
- PIN(INPUT, gpf1-2, DOWN, FAST_SR1);
- PIN(INPUT, gpf1-4, UP, FAST_SR1);
- PIN(OUTPUT, gpf1-5, NONE, FAST_SR1);
- PIN(INPUT, gpf1-6, DOWN, FAST_SR1);
- PIN(INPUT, gpf1-7, DOWN, FAST_SR1);
-
- PIN(INPUT, gpf2-0, DOWN, FAST_SR1);
- PIN(INPUT, gpf2-1, DOWN, FAST_SR1);
- PIN(INPUT, gpf2-2, DOWN, FAST_SR1);
- PIN(INPUT, gpf2-3, DOWN, FAST_SR1);
-
- PIN(INPUT, gpf3-0, DOWN, FAST_SR1);
- PIN(INPUT, gpf3-1, DOWN, FAST_SR1);
- PIN(INPUT, gpf3-2, NONE, FAST_SR1);
- PIN(INPUT, gpf3-3, DOWN, FAST_SR1);
-
- PIN(INPUT, gpf4-0, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-1, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-2, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-3, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-4, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-5, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-6, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-7, DOWN, FAST_SR1);
-
- PIN(INPUT, gpf5-0, DOWN, FAST_SR1);
- PIN(INPUT, gpf5-1, DOWN, FAST_SR1);
- PIN(INPUT, gpf5-2, DOWN, FAST_SR1);
- PIN(INPUT, gpf5-3, DOWN, FAST_SR1);
- PIN(OUTPUT, gpf5-4, NONE, FAST_SR1);
- PIN(INPUT, gpf5-5, DOWN, FAST_SR1);
- PIN(INPUT, gpf5-6, DOWN, FAST_SR1);
- PIN(INPUT, gpf5-7, DOWN, FAST_SR1);
- };
-
- te_irq: te_irq {
- samsung,pins = "gpf1-3";
- samsung,pin-function = <0xf>;
- };
-};
-
-&pinctrl_cpif {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_cpif>;
-
- initial_cpif: initial-state {
- PIN(INPUT, gpv6-0, DOWN, FAST_SR1);
- PIN(INPUT, gpv6-1, DOWN, FAST_SR1);
- };
-};
-
-&pinctrl_ese {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_ese>;
-
- initial_ese: initial-state {
- PIN(INPUT, gpj2-0, DOWN, FAST_SR1);
- PIN(INPUT, gpj2-1, DOWN, FAST_SR1);
- PIN(INPUT, gpj2-2, DOWN, FAST_SR1);
- };
-};
-
-&pinctrl_fsys {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_fsys>;
-
- initial_fsys: initial-state {
- PIN(INPUT, gpr3-0, NONE, FAST_SR1);
- PIN(INPUT, gpr3-1, DOWN, FAST_SR1);
- PIN(INPUT, gpr3-2, DOWN, FAST_SR1);
- PIN(INPUT, gpr3-3, DOWN, FAST_SR1);
- PIN(INPUT, gpr3-7, NONE, FAST_SR1);
- };
-};
-
-&pinctrl_imem {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_imem>;
-
- initial_imem: initial-state {
- PIN(INPUT, gpf0-0, UP, FAST_SR1);
- PIN(INPUT, gpf0-1, UP, FAST_SR1);
- PIN(INPUT, gpf0-2, DOWN, FAST_SR1);
- PIN(INPUT, gpf0-3, UP, FAST_SR1);
- PIN(INPUT, gpf0-4, DOWN, FAST_SR1);
- PIN(INPUT, gpf0-5, NONE, FAST_SR1);
- PIN(INPUT, gpf0-6, DOWN, FAST_SR1);
- PIN(INPUT, gpf0-7, UP, FAST_SR1);
- };
-};
-
-&pinctrl_nfc {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_nfc>;
-
- initial_nfc: initial-state {
- PIN(INPUT, gpj0-2, DOWN, FAST_SR1);
- };
-};
-
-&pinctrl_peric {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_peric>;
-
- initial_peric: initial-state {
- PIN(INPUT, gpv7-0, DOWN, FAST_SR1);
- PIN(INPUT, gpv7-1, DOWN, FAST_SR1);
- PIN(INPUT, gpv7-2, NONE, FAST_SR1);
- PIN(INPUT, gpv7-3, DOWN, FAST_SR1);
- PIN(INPUT, gpv7-4, DOWN, FAST_SR1);
- PIN(INPUT, gpv7-5, DOWN, FAST_SR1);
-
- PIN(INPUT, gpb0-4, DOWN, FAST_SR1);
-
- PIN(INPUT, gpc0-2, DOWN, FAST_SR1);
- PIN(INPUT, gpc0-5, DOWN, FAST_SR1);
- PIN(INPUT, gpc0-7, DOWN, FAST_SR1);
-
- PIN(INPUT, gpc1-1, DOWN, FAST_SR1);
-
- PIN(INPUT, gpc3-4, NONE, FAST_SR1);
- PIN(INPUT, gpc3-5, NONE, FAST_SR1);
- PIN(INPUT, gpc3-6, NONE, FAST_SR1);
- PIN(INPUT, gpc3-7, NONE, FAST_SR1);
-
- PIN(OUTPUT, gpg0-0, NONE, FAST_SR1);
- PIN(2, gpg0-1, DOWN, FAST_SR1);
-
- PIN(INPUT, gpd2-5, DOWN, FAST_SR1);
-
- PIN(INPUT, gpd4-0, NONE, FAST_SR1);
- PIN(INPUT, gpd4-1, DOWN, FAST_SR1);
- PIN(INPUT, gpd4-2, DOWN, FAST_SR1);
- PIN(INPUT, gpd4-3, DOWN, FAST_SR1);
- PIN(INPUT, gpd4-4, DOWN, FAST_SR1);
-
- PIN(INPUT, gpd6-3, DOWN, FAST_SR1);
-
- PIN(INPUT, gpd8-1, UP, FAST_SR1);
-
- PIN(INPUT, gpg1-0, DOWN, FAST_SR1);
- PIN(INPUT, gpg1-1, DOWN, FAST_SR1);
- PIN(INPUT, gpg1-2, DOWN, FAST_SR1);
- PIN(INPUT, gpg1-3, DOWN, FAST_SR1);
- PIN(INPUT, gpg1-4, DOWN, FAST_SR1);
-
- PIN(INPUT, gpg2-0, DOWN, FAST_SR1);
- PIN(INPUT, gpg2-1, DOWN, FAST_SR1);
-
- PIN(INPUT, gpg3-0, DOWN, FAST_SR1);
- PIN(INPUT, gpg3-1, DOWN, FAST_SR1);
- PIN(INPUT, gpg3-5, DOWN, FAST_SR1);
- PIN(INPUT, gpg3-7, DOWN, FAST_SR1);
- };
-};
-
-&pinctrl_touch {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_touch>;
-
- initial_touch: initial-state {
- PIN(INPUT, gpj1-2, DOWN, FAST_SR1);
- };
-};
-
-&pwm {
- pinctrl-0 = <&pwm0_out>;
- pinctrl-names = "default";
- status = "okay";
-};
-
-&mic {
- status = "okay";
-
- i80-if-timings {
- };
-};
-
-&pmu_system_controller {
- assigned-clocks = <&pmu_system_controller 0>;
- assigned-clock-parents = <&xxti>;
-};
-
-&serial_1 {
- status = "okay";
-};
-
-&spi_1 {
- cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
- status = "okay";
-
- wm5110: wm5110-codec@0 {
- compatible = "wlf,wm5110";
- reg = <0x0>;
- spi-max-frequency = <20000000>;
- interrupt-parent = <&gpa0>;
- interrupts = <4 IRQ_TYPE_NONE>;
- clocks = <&pmu_system_controller 0>,
- <&s2mps13_osc S2MPS11_CLK_BT>;
- clock-names = "mclk1", "mclk2";
-
- gpio-controller;
- #gpio-cells = <2>;
-
- wlf,micd-detect-debounce = <300>;
- wlf,micd-bias-start-time = <0x1>;
- wlf,micd-rate = <0x7>;
- wlf,micd-dbtime = <0x1>;
- wlf,micd-force-micbias;
- wlf,micd-configs = <0x0 1 0>;
- wlf,hpdet-channel = <1>;
- wlf,gpsw = <0x1>;
- wlf,inmode = <2 0 2 0>;
-
- wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
- wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
-
- /* core supplies */
- AVDD-supply = <&ldo18_reg>;
- DBVDD1-supply = <&ldo18_reg>;
- CPVDD-supply = <&ldo18_reg>;
- DBVDD2-supply = <&ldo18_reg>;
- DBVDD3-supply = <&ldo18_reg>;
-
- controller-data {
- samsung,spi-feedback-delay = <0>;
- };
- };
-};
-
-&timer {
- clock-frequency = <24000000>;
-};
-
-&tmu_atlas0 {
- vtmu-supply = <&ldo3_reg>;
- status = "okay";
-};
-
-&tmu_apollo {
- vtmu-supply = <&ldo3_reg>;
- status = "okay";
-};
-
-&tmu_g3d {
- vtmu-supply = <&ldo3_reg>;
- status = "okay";
-};
-
-&usbdrd30 {
- vdd33-supply = <&ldo10_reg>;
- vdd10-supply = <&ldo6_reg>;
- status = "okay";
-};
-
-&usbdrd_dwc3_0 {
- dr_mode = "otg";
-};
-
-&usbdrd30_phy {
- vbus-supply = <&safeout1_reg>;
- status = "okay";
-};
-
-&xxti {
- clock-frequency = <24000000>;
-};
+/*
+ * SAMSUNG Exynos5433 TM2 board device tree source
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *
+ * Device tree source file for Samsung's TM2 board which is based on
+ * Samsung Exynos5433 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "exynos5433-tm2-common.dtsi"
+
+/ {
+ model = "Samsung TM2E board";
+ compatible = "samsung,tm2e", "samsung,exynos5433";
+};
+
+®ulators {
+ ldo31_reg: LDO31 {
+ regulator-name = "TSP_VDD_1.85V_AP";
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <1850000>;
+ };
+
+ ldo38_reg: LDO38 {
+ regulator-name = "VCC_3.0V_MOTOR_AP";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
index 854c583..53e361f 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
@@ -11,21 +11,23 @@
* published by the Free Software Foundation.
*/
-#include "exynos5433-tm2.dts"
+#include "exynos5433-tm2-common.dtsi"
/ {
model = "Samsung TM2E board";
compatible = "samsung,tm2e", "samsung,exynos5433";
};
-&ldo31_reg {
- regulator-name = "TSP_VDD_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-};
+®ulators {
+ ldo31_reg: LDO31 {
+ regulator-name = "TSP_VDD_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
-&ldo38_reg {
- regulator-name = "VCC_3.3V_MOTOR_AP";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
+ ldo38_reg: LDO38 {
+ regulator-name = "VCC_3.3V_MOTOR_AP";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
};
--
2.7.4
next prev parent reply other threads:[~2017-01-06 4:01 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <CGME20170106035913epcas5p2b7d66596e467c6169786eea56beb8ffc@epcas5p2.samsung.com>
2017-01-06 3:59 ` [PATCH v3 0/5] Add touch key driver support for TM2 Jaechul Lee
[not found] ` <CGME20170106035913epcas5p20336406863f1029ccf614520f366ddcf@epcas5p2.samsung.com>
2017-01-06 3:59 ` [PATCH v3 1/5] arm64: dts: exynos5433: TM2/E: Fix wrong information of ldo23 and ldo25 Jaechul Lee
2017-01-06 7:05 ` Krzysztof Kozlowski
2017-01-06 7:20 ` Chanwoo Choi
2017-01-06 8:50 ` Krzysztof Kozlowski
2017-01-06 9:06 ` Chanwoo Choi
2017-01-06 9:12 ` Krzysztof Kozlowski
[not found] ` <CGME20170106035914epcas5p209490dfca8e8ae83c6a9b5aa1408a1ed@epcas5p2.samsung.com>
2017-01-06 3:59 ` Jaechul Lee [this message]
2017-01-06 7:09 ` [PATCH v3 2/5] arm64: dts: exynos: make tm2 and tm2e independent from each other Krzysztof Kozlowski
2017-01-06 7:59 ` Andi Shyti
2017-01-06 8:37 ` Krzysztof Kozlowski
2017-01-06 9:25 ` Andi Shyti
[not found] ` <CGME20170106035914epcas5p2954865ce8060c6aaee61a7526e417b7d@epcas5p2.samsung.com>
2017-01-06 3:59 ` [PATCH v3 3/5] input: Add support for the tm2 touchkey device driver Jaechul Lee
[not found] ` <CGME20170106035914epcas5p20aa47294b5667e8842587c63cd2b4f3e@epcas5p2.samsung.com>
2017-01-06 3:59 ` [PATCH v3 4/5] input: tm2-touchkey: Add touchkey driver support for TM2 Jaechul Lee
[not found] ` <CGME20170106035914epcas5p2bd9b2358c41d32f7a677d75afba95144@epcas5p2.samsung.com>
2017-01-06 3:59 ` [PATCH v3 5/5] arm64: dts: exynos: Add tm2 touchkey node Jaechul Lee
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1483675149-32598-3-git-send-email-jcsing.lee@samsung.com \
--to=jcsing.lee@samsung.com \
--cc=andi.shyti@samsung.com \
--cc=beomho.seo@samsung.com \
--cc=catalin.marinas@arm.com \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.torokhov@gmail.com \
--cc=galaxyra@gmail.com \
--cc=javier@osg.samsung.com \
--cc=kgene@kernel.org \
--cc=krzk@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).