* [PATCH 1/6] usb: mtu3: get resources that cause deferred probe earlier
@ 2017-01-18 6:08 Chunfeng Yun
2017-01-18 6:08 ` [PATCH 2/6] usb: mtu3: add reference clock Chunfeng Yun
` (4 more replies)
0 siblings, 5 replies; 19+ messages in thread
From: Chunfeng Yun @ 2017-01-18 6:08 UTC (permalink / raw)
To: Mathias Nyman, Felipe Balbi
Cc: Greg Kroah-Hartman, Matthias Brugger, Rob Herring, Mark Rutland,
Ian Campbell, Chunfeng Yun, linux-kernel, linux-arm-kernel,
linux-usb, linux-mediatek, devicetree
Some resources such as regulator, clock usually cause deferred
probe, get them earlier to avoid more ineffective processing.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
drivers/usb/mtu3/mtu3_plat.c | 24 ++++++++++++------------
1 file changed, 12 insertions(+), 12 deletions(-)
diff --git a/drivers/usb/mtu3/mtu3_plat.c b/drivers/usb/mtu3/mtu3_plat.c
index 7833678..6344859 100644
--- a/drivers/usb/mtu3/mtu3_plat.c
+++ b/drivers/usb/mtu3/mtu3_plat.c
@@ -204,6 +204,18 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb)
int i;
int ret;
+ ssusb->vusb33 = devm_regulator_get(&pdev->dev, "vusb33");
+ if (IS_ERR(ssusb->vusb33)) {
+ dev_err(dev, "failed to get vusb33\n");
+ return PTR_ERR(ssusb->vusb33);
+ }
+
+ ssusb->sys_clk = devm_clk_get(dev, "sys_ck");
+ if (IS_ERR(ssusb->sys_clk)) {
+ dev_err(dev, "failed to get sys clock\n");
+ return PTR_ERR(ssusb->sys_clk);
+ }
+
ssusb->num_phys = of_count_phandle_with_args(node,
"phys", "#phy-cells");
if (ssusb->num_phys > 0) {
@@ -230,18 +242,6 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb)
return PTR_ERR(ssusb->ippc_base);
}
- ssusb->vusb33 = devm_regulator_get(&pdev->dev, "vusb33");
- if (IS_ERR(ssusb->vusb33)) {
- dev_err(dev, "failed to get vusb33\n");
- return PTR_ERR(ssusb->vusb33);
- }
-
- ssusb->sys_clk = devm_clk_get(dev, "sys_ck");
- if (IS_ERR(ssusb->sys_clk)) {
- dev_err(dev, "failed to get sys clock\n");
- return PTR_ERR(ssusb->sys_clk);
- }
-
ssusb->dr_mode = usb_get_dr_mode(dev);
if (ssusb->dr_mode == USB_DR_MODE_UNKNOWN) {
dev_err(dev, "dr_mode is error\n");
--
1.7.9.5
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 2/6] usb: mtu3: add reference clock
2017-01-18 6:08 [PATCH 1/6] usb: mtu3: get resources that cause deferred probe earlier Chunfeng Yun
@ 2017-01-18 6:08 ` Chunfeng Yun
2017-01-19 12:22 ` Matthias Brugger
2017-01-18 6:08 ` [PATCH 3/6] usb: xhci-mtk: " Chunfeng Yun
` (3 subsequent siblings)
4 siblings, 1 reply; 19+ messages in thread
From: Chunfeng Yun @ 2017-01-18 6:08 UTC (permalink / raw)
To: Mathias Nyman, Felipe Balbi
Cc: Greg Kroah-Hartman, Matthias Brugger, Rob Herring, Mark Rutland,
Ian Campbell, Chunfeng Yun, linux-kernel, linux-arm-kernel,
linux-usb, linux-mediatek, devicetree
usually, the reference clock comes from 26M oscillator directly,
but some SoCs are not, add it for compatibility.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
drivers/usb/mtu3/mtu3.h | 1 +
drivers/usb/mtu3/mtu3_plat.c | 21 +++++++++++++++++++--
2 files changed, 20 insertions(+), 2 deletions(-)
diff --git a/drivers/usb/mtu3/mtu3.h b/drivers/usb/mtu3/mtu3.h
index ba9df71..aa6fd6a 100644
--- a/drivers/usb/mtu3/mtu3.h
+++ b/drivers/usb/mtu3/mtu3.h
@@ -225,6 +225,7 @@ struct ssusb_mtk {
/* common power & clock */
struct regulator *vusb33;
struct clk *sys_clk;
+ struct clk *ref_clk;
/* otg */
struct otg_switch_mtk otg_switch;
enum usb_dr_mode dr_mode;
diff --git a/drivers/usb/mtu3/mtu3_plat.c b/drivers/usb/mtu3/mtu3_plat.c
index 6344859..19a345d 100644
--- a/drivers/usb/mtu3/mtu3_plat.c
+++ b/drivers/usb/mtu3/mtu3_plat.c
@@ -123,7 +123,13 @@ static int ssusb_rscs_init(struct ssusb_mtk *ssusb)
ret = clk_prepare_enable(ssusb->sys_clk);
if (ret) {
dev_err(ssusb->dev, "failed to enable sys_clk\n");
- goto clk_err;
+ goto sys_clk_err;
+ }
+
+ ret = clk_prepare_enable(ssusb->ref_clk);
+ if (ret) {
+ dev_err(ssusb->dev, "failed to enable ref_clk\n");
+ goto ref_clk_err;
}
ret = ssusb_phy_init(ssusb);
@@ -143,8 +149,10 @@ static int ssusb_rscs_init(struct ssusb_mtk *ssusb)
phy_err:
ssusb_phy_exit(ssusb);
phy_init_err:
+ clk_disable_unprepare(ssusb->ref_clk);
+ref_clk_err:
clk_disable_unprepare(ssusb->sys_clk);
-clk_err:
+sys_clk_err:
regulator_disable(ssusb->vusb33);
vusb33_err:
@@ -154,6 +162,7 @@ static int ssusb_rscs_init(struct ssusb_mtk *ssusb)
static void ssusb_rscs_exit(struct ssusb_mtk *ssusb)
{
clk_disable_unprepare(ssusb->sys_clk);
+ clk_disable_unprepare(ssusb->ref_clk);
regulator_disable(ssusb->vusb33);
ssusb_phy_power_off(ssusb);
ssusb_phy_exit(ssusb);
@@ -216,6 +225,12 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb)
return PTR_ERR(ssusb->sys_clk);
}
+ ssusb->ref_clk = devm_clk_get(dev, "ref_ck");
+ if (IS_ERR(ssusb->ref_clk)) {
+ dev_err(dev, "failed to get ref clock\n");
+ return PTR_ERR(ssusb->ref_clk);
+ }
+
ssusb->num_phys = of_count_phandle_with_args(node,
"phys", "#phy-cells");
if (ssusb->num_phys > 0) {
@@ -428,6 +443,7 @@ static int __maybe_unused mtu3_suspend(struct device *dev)
ssusb_host_disable(ssusb, true);
ssusb_phy_power_off(ssusb);
clk_disable_unprepare(ssusb->sys_clk);
+ clk_disable_unprepare(ssusb->ref_clk);
ssusb_wakeup_enable(ssusb);
return 0;
@@ -445,6 +461,7 @@ static int __maybe_unused mtu3_resume(struct device *dev)
ssusb_wakeup_disable(ssusb);
clk_prepare_enable(ssusb->sys_clk);
+ clk_prepare_enable(ssusb->ref_clk);
ssusb_phy_power_on(ssusb);
ssusb_host_enable(ssusb);
--
1.7.9.5
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 3/6] usb: xhci-mtk: add reference clock
2017-01-18 6:08 [PATCH 1/6] usb: mtu3: get resources that cause deferred probe earlier Chunfeng Yun
2017-01-18 6:08 ` [PATCH 2/6] usb: mtu3: add reference clock Chunfeng Yun
@ 2017-01-18 6:08 ` Chunfeng Yun
2017-01-18 6:08 ` [PATCH 4/6] arm64: dts: mt8173: add reference clock for usb Chunfeng Yun
` (2 subsequent siblings)
4 siblings, 0 replies; 19+ messages in thread
From: Chunfeng Yun @ 2017-01-18 6:08 UTC (permalink / raw)
To: Mathias Nyman, Felipe Balbi
Cc: Greg Kroah-Hartman, Matthias Brugger, Rob Herring, Mark Rutland,
Ian Campbell, Chunfeng Yun, linux-kernel, linux-arm-kernel,
linux-usb, linux-mediatek, devicetree
usually, the reference clock comes from 26M oscillator directly,
but some SoCs are not, add it for compatibility.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
drivers/usb/host/xhci-mtk.c | 15 +++++++++++++++
drivers/usb/host/xhci-mtk.h | 1 +
2 files changed, 16 insertions(+)
diff --git a/drivers/usb/host/xhci-mtk.c b/drivers/usb/host/xhci-mtk.c
index 1094ebd..4d75ac5 100644
--- a/drivers/usb/host/xhci-mtk.c
+++ b/drivers/usb/host/xhci-mtk.c
@@ -212,6 +212,12 @@ static int xhci_mtk_clks_enable(struct xhci_hcd_mtk *mtk)
{
int ret;
+ ret = clk_prepare_enable(mtk->ref_clk);
+ if (ret) {
+ dev_err(mtk->dev, "failed to enable ref_clk\n");
+ goto ref_clk_err;
+ }
+
ret = clk_prepare_enable(mtk->sys_clk);
if (ret) {
dev_err(mtk->dev, "failed to enable sys_clk\n");
@@ -238,6 +244,8 @@ static int xhci_mtk_clks_enable(struct xhci_hcd_mtk *mtk)
usb_p0_err:
clk_disable_unprepare(mtk->sys_clk);
sys_clk_err:
+ clk_disable_unprepare(mtk->ref_clk);
+ref_clk_err:
return -EINVAL;
}
@@ -248,6 +256,7 @@ static void xhci_mtk_clks_disable(struct xhci_hcd_mtk *mtk)
clk_disable_unprepare(mtk->wk_deb_p0);
}
clk_disable_unprepare(mtk->sys_clk);
+ clk_disable_unprepare(mtk->ref_clk);
}
/* only clocks can be turn off for ip-sleep wakeup mode */
@@ -550,6 +559,12 @@ static int xhci_mtk_probe(struct platform_device *pdev)
return PTR_ERR(mtk->sys_clk);
}
+ mtk->ref_clk = devm_clk_get(dev, "ref_ck");
+ if (IS_ERR(mtk->ref_clk)) {
+ dev_err(dev, "fail to get ref_ck\n");
+ return PTR_ERR(mtk->ref_clk);
+ }
+
mtk->lpm_support = of_property_read_bool(node, "usb3-lpm-capable");
ret = usb_wakeup_of_property_parse(mtk, node);
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index 2845c49..3aa5e1d 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -124,6 +124,7 @@ struct xhci_hcd_mtk {
struct regulator *vusb33;
struct regulator *vbus;
struct clk *sys_clk; /* sys and mac clock */
+ struct clk *ref_clk;
struct clk *wk_deb_p0; /* port0's wakeup debounce clock */
struct clk *wk_deb_p1;
struct regmap *pericfg;
--
1.7.9.5
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 4/6] arm64: dts: mt8173: add reference clock for usb
2017-01-18 6:08 [PATCH 1/6] usb: mtu3: get resources that cause deferred probe earlier Chunfeng Yun
2017-01-18 6:08 ` [PATCH 2/6] usb: mtu3: add reference clock Chunfeng Yun
2017-01-18 6:08 ` [PATCH 3/6] usb: xhci-mtk: " Chunfeng Yun
@ 2017-01-18 6:08 ` Chunfeng Yun
2017-01-19 9:37 ` Greg Kroah-Hartman
2017-01-18 6:08 ` [PATCH 5/6] dt-bindings: mt8173-xhci: add reference clock Chunfeng Yun
2017-01-18 6:08 ` [PATCH 6/6] dt-bindings: mt8173-mtu3: " Chunfeng Yun
4 siblings, 1 reply; 19+ messages in thread
From: Chunfeng Yun @ 2017-01-18 6:08 UTC (permalink / raw)
To: Mathias Nyman, Felipe Balbi
Cc: Greg Kroah-Hartman, Matthias Brugger, Rob Herring, Mark Rutland,
Ian Campbell, Chunfeng Yun, linux-kernel, linux-arm-kernel,
linux-usb, linux-mediatek, devicetree
add 26M reference clock for ssusb and xhci nodes
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
arch/arm64/boot/dts/mediatek/mt8173.dtsi | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
index 07fd2eb..e2862b6 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -729,9 +729,11 @@
<&u2port1 PHY_TYPE_USB2>;
power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
clocks = <&topckgen CLK_TOP_USB30_SEL>,
+ <&clk26m>,
<&pericfg CLK_PERI_USB0>,
<&pericfg CLK_PERI_USB1>;
clock-names = "sys_ck",
+ "ref_ck",
"wakeup_deb_p0",
"wakeup_deb_p1";
mediatek,syscon-wakeup = <&pericfg>;
@@ -746,8 +748,8 @@
reg-names = "mac";
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
- clocks = <&topckgen CLK_TOP_USB30_SEL>;
- clock-names = "sys_ck";
+ clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
+ clock-names = "sys_ck", "ref_ck";
status = "disabled";
};
};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 5/6] dt-bindings: mt8173-xhci: add reference clock
2017-01-18 6:08 [PATCH 1/6] usb: mtu3: get resources that cause deferred probe earlier Chunfeng Yun
` (2 preceding siblings ...)
2017-01-18 6:08 ` [PATCH 4/6] arm64: dts: mt8173: add reference clock for usb Chunfeng Yun
@ 2017-01-18 6:08 ` Chunfeng Yun
2017-01-21 20:10 ` Rob Herring
2017-01-21 20:12 ` Rob Herring
2017-01-18 6:08 ` [PATCH 6/6] dt-bindings: mt8173-mtu3: " Chunfeng Yun
4 siblings, 2 replies; 19+ messages in thread
From: Chunfeng Yun @ 2017-01-18 6:08 UTC (permalink / raw)
To: Mathias Nyman, Felipe Balbi
Cc: Greg Kroah-Hartman, Matthias Brugger, Rob Herring, Mark Rutland,
Ian Campbell, Chunfeng Yun, linux-kernel, linux-arm-kernel,
linux-usb, linux-mediatek, devicetree
add a reference clock for compatibility
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
.../devicetree/bindings/usb/mt8173-xhci.txt | 10 ++++++----
1 file changed, 6 insertions(+), 4 deletions(-)
diff --git a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
index 2a930bd..ab8bb27 100644
--- a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
+++ b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
@@ -23,6 +23,7 @@ Required properties:
entry in clock-names
- clock-names : must contain
"sys_ck": for clock of xHCI MAC
+ "ref_ck": for reference clock of xHCI MAC
"wakeup_deb_p0": for USB wakeup debounce clock of port0
"wakeup_deb_p1": for USB wakeup debounce clock of port1
@@ -47,10 +48,10 @@ usb30: usb@11270000 {
reg-names = "mac", "ippc";
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
- clocks = <&topckgen CLK_TOP_USB30_SEL>,
+ clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>,
<&pericfg CLK_PERI_USB0>,
<&pericfg CLK_PERI_USB1>;
- clock-names = "sys_ck",
+ clock-names = "sys_ck", "ref_ck",
"wakeup_deb_p0",
"wakeup_deb_p1";
phys = <&phy_port0 PHY_TYPE_USB3>,
@@ -82,6 +83,7 @@ Required properties:
entry in clock-names
- clock-names : must be
"sys_ck": for clock of xHCI MAC
+ "ref_ck": for reference clock of xHCI MAC
Optional properties:
- vbus-supply : reference to the VBUS regulator;
@@ -94,8 +96,8 @@ usb30: usb@11270000 {
reg-names = "mac";
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
- clocks = <&topckgen CLK_TOP_USB30_SEL>;
- clock-names = "sys_ck";
+ clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
+ clock-names = "sys_ck", "ref_ck";
vusb33-supply = <&mt6397_vusb_reg>;
usb3-lpm-capable;
};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 6/6] dt-bindings: mt8173-mtu3: add reference clock
2017-01-18 6:08 [PATCH 1/6] usb: mtu3: get resources that cause deferred probe earlier Chunfeng Yun
` (3 preceding siblings ...)
2017-01-18 6:08 ` [PATCH 5/6] dt-bindings: mt8173-xhci: add reference clock Chunfeng Yun
@ 2017-01-18 6:08 ` Chunfeng Yun
2017-01-21 20:11 ` Rob Herring
4 siblings, 1 reply; 19+ messages in thread
From: Chunfeng Yun @ 2017-01-18 6:08 UTC (permalink / raw)
To: Mathias Nyman, Felipe Balbi
Cc: Greg Kroah-Hartman, Matthias Brugger, Rob Herring, Mark Rutland,
Ian Campbell, Chunfeng Yun, linux-kernel, linux-arm-kernel,
linux-usb, linux-mediatek, devicetree
add a reference clock for compatibility
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
.../devicetree/bindings/usb/mt8173-mtu3.txt | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
index e049d19..8c976cd 100644
--- a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
+++ b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
@@ -10,7 +10,7 @@ Required properties:
- vusb33-supply : regulator of USB avdd3.3v
- clocks : a list of phandle + clock-specifier pairs, one for each
entry in clock-names
- - clock-names : must contain "sys_ck" for clock of controller;
+ - clock-names : must contain "sys_ck" and "ref_ck" for clock of controller;
"wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are
depends on "mediatek,enable-wakeup"
- phys : a list of phandle + phy specifier pairs
@@ -56,10 +56,10 @@ ssusb: usb@11271000 {
phys = <&phy_port0 PHY_TYPE_USB3>,
<&phy_port1 PHY_TYPE_USB2>;
power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
- clocks = <&topckgen CLK_TOP_USB30_SEL>,
+ clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>,
<&pericfg CLK_PERI_USB0>,
<&pericfg CLK_PERI_USB1>;
- clock-names = "sys_ck",
+ clock-names = "sys_ck", "ref_ck",
"wakeup_deb_p0",
"wakeup_deb_p1";
vusb33-supply = <&mt6397_vusb_reg>;
@@ -79,8 +79,8 @@ ssusb: usb@11271000 {
reg-names = "mac";
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
- clocks = <&topckgen CLK_TOP_USB30_SEL>;
- clock-names = "sys_ck";
+ clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
+ clock-names = "sys_ck", "ref_ck";
vusb33-supply = <&mt6397_vusb_reg>;
status = "disabled";
};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH 4/6] arm64: dts: mt8173: add reference clock for usb
2017-01-18 6:08 ` [PATCH 4/6] arm64: dts: mt8173: add reference clock for usb Chunfeng Yun
@ 2017-01-19 9:37 ` Greg Kroah-Hartman
2017-01-19 12:23 ` Matthias Brugger
0 siblings, 1 reply; 19+ messages in thread
From: Greg Kroah-Hartman @ 2017-01-19 9:37 UTC (permalink / raw)
To: Chunfeng Yun
Cc: Mathias Nyman, Felipe Balbi, Matthias Brugger, Rob Herring,
Mark Rutland, Ian Campbell, linux-kernel, linux-arm-kernel,
linux-usb, linux-mediatek, devicetree
On Wed, Jan 18, 2017 at 02:08:25PM +0800, Chunfeng Yun wrote:
> add 26M reference clock for ssusb and xhci nodes
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> arch/arm64/boot/dts/mediatek/mt8173.dtsi | 6 ++++--
> 1 file changed, 4 insertions(+), 2 deletions(-)
This patch doesn't apply to my tree :(
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 2/6] usb: mtu3: add reference clock
2017-01-18 6:08 ` [PATCH 2/6] usb: mtu3: add reference clock Chunfeng Yun
@ 2017-01-19 12:22 ` Matthias Brugger
2017-01-20 2:20 ` Chunfeng Yun
0 siblings, 1 reply; 19+ messages in thread
From: Matthias Brugger @ 2017-01-19 12:22 UTC (permalink / raw)
To: Chunfeng Yun, Mathias Nyman, Felipe Balbi
Cc: Greg Kroah-Hartman, Rob Herring, Mark Rutland, Ian Campbell,
linux-kernel, linux-arm-kernel, linux-usb, linux-mediatek,
devicetree
On 18/01/17 07:08, Chunfeng Yun wrote:
> usually, the reference clock comes from 26M oscillator directly,
> but some SoCs are not, add it for compatibility.
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> drivers/usb/mtu3/mtu3.h | 1 +
> drivers/usb/mtu3/mtu3_plat.c | 21 +++++++++++++++++++--
> 2 files changed, 20 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/usb/mtu3/mtu3.h b/drivers/usb/mtu3/mtu3.h
> index ba9df71..aa6fd6a 100644
> --- a/drivers/usb/mtu3/mtu3.h
> +++ b/drivers/usb/mtu3/mtu3.h
> @@ -225,6 +225,7 @@ struct ssusb_mtk {
> /* common power & clock */
> struct regulator *vusb33;
> struct clk *sys_clk;
> + struct clk *ref_clk;
> /* otg */
> struct otg_switch_mtk otg_switch;
> enum usb_dr_mode dr_mode;
> diff --git a/drivers/usb/mtu3/mtu3_plat.c b/drivers/usb/mtu3/mtu3_plat.c
> index 6344859..19a345d 100644
> --- a/drivers/usb/mtu3/mtu3_plat.c
> +++ b/drivers/usb/mtu3/mtu3_plat.c
> @@ -123,7 +123,13 @@ static int ssusb_rscs_init(struct ssusb_mtk *ssusb)
> ret = clk_prepare_enable(ssusb->sys_clk);
> if (ret) {
> dev_err(ssusb->dev, "failed to enable sys_clk\n");
> - goto clk_err;
> + goto sys_clk_err;
> + }
> +
> + ret = clk_prepare_enable(ssusb->ref_clk);
> + if (ret) {
> + dev_err(ssusb->dev, "failed to enable ref_clk\n");
> + goto ref_clk_err;
> }
>
> ret = ssusb_phy_init(ssusb);
> @@ -143,8 +149,10 @@ static int ssusb_rscs_init(struct ssusb_mtk *ssusb)
> phy_err:
> ssusb_phy_exit(ssusb);
> phy_init_err:
> + clk_disable_unprepare(ssusb->ref_clk);
> +ref_clk_err:
> clk_disable_unprepare(ssusb->sys_clk);
> -clk_err:
> +sys_clk_err:
> regulator_disable(ssusb->vusb33);
> vusb33_err:
>
> @@ -154,6 +162,7 @@ static int ssusb_rscs_init(struct ssusb_mtk *ssusb)
> static void ssusb_rscs_exit(struct ssusb_mtk *ssusb)
> {
> clk_disable_unprepare(ssusb->sys_clk);
> + clk_disable_unprepare(ssusb->ref_clk);
> regulator_disable(ssusb->vusb33);
> ssusb_phy_power_off(ssusb);
> ssusb_phy_exit(ssusb);
> @@ -216,6 +225,12 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb)
> return PTR_ERR(ssusb->sys_clk);
> }
>
> + ssusb->ref_clk = devm_clk_get(dev, "ref_ck");
> + if (IS_ERR(ssusb->ref_clk)) {
> + dev_err(dev, "failed to get ref clock\n");
> + return PTR_ERR(ssusb->ref_clk);
> + }
> +
That would break older dts bindings, right?
ref_ck must be optional for the code.
Regards,
Matthias
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 4/6] arm64: dts: mt8173: add reference clock for usb
2017-01-19 9:37 ` Greg Kroah-Hartman
@ 2017-01-19 12:23 ` Matthias Brugger
0 siblings, 0 replies; 19+ messages in thread
From: Matthias Brugger @ 2017-01-19 12:23 UTC (permalink / raw)
To: Greg Kroah-Hartman, Chunfeng Yun
Cc: Mathias Nyman, Felipe Balbi, Rob Herring, Mark Rutland,
Ian Campbell, linux-kernel, linux-arm-kernel, linux-usb,
linux-mediatek, devicetree
On 19/01/17 10:37, Greg Kroah-Hartman wrote:
> On Wed, Jan 18, 2017 at 02:08:25PM +0800, Chunfeng Yun wrote:
>> add 26M reference clock for ssusb and xhci nodes
>>
>> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
>> ---
>> arch/arm64/boot/dts/mediatek/mt8173.dtsi | 6 ++++--
>> 1 file changed, 4 insertions(+), 2 deletions(-)
>
> This patch doesn't apply to my tree :(
>
This patch should go through my tree, but take into account my comment
on patch 3/6. From my point of view this series is not ready to be merged.
Regards,
Matthias
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 2/6] usb: mtu3: add reference clock
2017-01-19 12:22 ` Matthias Brugger
@ 2017-01-20 2:20 ` Chunfeng Yun
2017-01-24 23:23 ` Matthias Brugger
0 siblings, 1 reply; 19+ messages in thread
From: Chunfeng Yun @ 2017-01-20 2:20 UTC (permalink / raw)
To: Matthias Brugger
Cc: Mathias Nyman, Felipe Balbi, Greg Kroah-Hartman, Rob Herring,
Mark Rutland, Ian Campbell, linux-kernel, linux-arm-kernel,
linux-usb, linux-mediatek, devicetree
On Thu, 2017-01-19 at 13:22 +0100, Matthias Brugger wrote:
>
> On 18/01/17 07:08, Chunfeng Yun wrote:
> > usually, the reference clock comes from 26M oscillator directly,
> > but some SoCs are not, add it for compatibility.
> >
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> > drivers/usb/mtu3/mtu3.h | 1 +
> > drivers/usb/mtu3/mtu3_plat.c | 21 +++++++++++++++++++--
> > 2 files changed, 20 insertions(+), 2 deletions(-)
[...]
> > @@ -154,6 +162,7 @@ static int ssusb_rscs_init(struct ssusb_mtk *ssusb)
> > static void ssusb_rscs_exit(struct ssusb_mtk *ssusb)
> > {
> > clk_disable_unprepare(ssusb->sys_clk);
> > + clk_disable_unprepare(ssusb->ref_clk);
> > regulator_disable(ssusb->vusb33);
> > ssusb_phy_power_off(ssusb);
> > ssusb_phy_exit(ssusb);
> > @@ -216,6 +225,12 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb)
> > return PTR_ERR(ssusb->sys_clk);
> > }
> >
> > + ssusb->ref_clk = devm_clk_get(dev, "ref_ck");
> > + if (IS_ERR(ssusb->ref_clk)) {
> > + dev_err(dev, "failed to get ref clock\n");
> > + return PTR_ERR(ssusb->ref_clk);
> > + }
> > +
>
> That would break older dts bindings, right?
Yes, So I send a new patch for the related dts. Maybe it's not a
problem, only one dts file need be updated currently.
> ref_ck must be optional for the code.
I tend to make it be optional for the dts, but not for the code.
There are some "fixed-clock" which can be treated as dummy ones, and if
a clock is really optional, we can use one fixed-clock in dts, and keep
the code simple.
In fact, the reference clock is essential for usb controller.
>
> Regards,
> Matthias
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 5/6] dt-bindings: mt8173-xhci: add reference clock
2017-01-18 6:08 ` [PATCH 5/6] dt-bindings: mt8173-xhci: add reference clock Chunfeng Yun
@ 2017-01-21 20:10 ` Rob Herring
2017-01-21 20:12 ` Rob Herring
1 sibling, 0 replies; 19+ messages in thread
From: Rob Herring @ 2017-01-21 20:10 UTC (permalink / raw)
To: Chunfeng Yun
Cc: Mathias Nyman, Felipe Balbi, Greg Kroah-Hartman,
Matthias Brugger, Mark Rutland, Ian Campbell, linux-kernel,
linux-arm-kernel, linux-usb, linux-mediatek, devicetree
On Wed, Jan 18, 2017 at 02:08:26PM +0800, Chunfeng Yun wrote:
> add a reference clock for compatibility
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> .../devicetree/bindings/usb/mt8173-xhci.txt | 10 ++++++----
> 1 file changed, 6 insertions(+), 4 deletions(-)
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 6/6] dt-bindings: mt8173-mtu3: add reference clock
2017-01-18 6:08 ` [PATCH 6/6] dt-bindings: mt8173-mtu3: " Chunfeng Yun
@ 2017-01-21 20:11 ` Rob Herring
2017-01-22 1:49 ` Chunfeng Yun
0 siblings, 1 reply; 19+ messages in thread
From: Rob Herring @ 2017-01-21 20:11 UTC (permalink / raw)
To: Chunfeng Yun
Cc: Mathias Nyman, Felipe Balbi, Greg Kroah-Hartman,
Matthias Brugger, Mark Rutland, Ian Campbell, linux-kernel,
linux-arm-kernel, linux-usb, linux-mediatek, devicetree
On Wed, Jan 18, 2017 at 02:08:27PM +0800, Chunfeng Yun wrote:
> add a reference clock for compatibility
Why? This block suddenly has 2 clocks instead of 1?
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> .../devicetree/bindings/usb/mt8173-mtu3.txt | 10 +++++-----
> 1 file changed, 5 insertions(+), 5 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
> index e049d19..8c976cd 100644
> --- a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
> +++ b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
> @@ -10,7 +10,7 @@ Required properties:
> - vusb33-supply : regulator of USB avdd3.3v
> - clocks : a list of phandle + clock-specifier pairs, one for each
> entry in clock-names
> - - clock-names : must contain "sys_ck" for clock of controller;
> + - clock-names : must contain "sys_ck" and "ref_ck" for clock of controller;
> "wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are
> depends on "mediatek,enable-wakeup"
> - phys : a list of phandle + phy specifier pairs
> @@ -56,10 +56,10 @@ ssusb: usb@11271000 {
> phys = <&phy_port0 PHY_TYPE_USB3>,
> <&phy_port1 PHY_TYPE_USB2>;
> power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
> - clocks = <&topckgen CLK_TOP_USB30_SEL>,
> + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>,
> <&pericfg CLK_PERI_USB0>,
> <&pericfg CLK_PERI_USB1>;
> - clock-names = "sys_ck",
> + clock-names = "sys_ck", "ref_ck",
> "wakeup_deb_p0",
> "wakeup_deb_p1";
> vusb33-supply = <&mt6397_vusb_reg>;
> @@ -79,8 +79,8 @@ ssusb: usb@11271000 {
> reg-names = "mac";
> interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
> power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
> - clocks = <&topckgen CLK_TOP_USB30_SEL>;
> - clock-names = "sys_ck";
> + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
> + clock-names = "sys_ck", "ref_ck";
> vusb33-supply = <&mt6397_vusb_reg>;
> status = "disabled";
> };
> --
> 1.7.9.5
>
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 5/6] dt-bindings: mt8173-xhci: add reference clock
2017-01-18 6:08 ` [PATCH 5/6] dt-bindings: mt8173-xhci: add reference clock Chunfeng Yun
2017-01-21 20:10 ` Rob Herring
@ 2017-01-21 20:12 ` Rob Herring
2017-01-22 1:53 ` Chunfeng Yun
1 sibling, 1 reply; 19+ messages in thread
From: Rob Herring @ 2017-01-21 20:12 UTC (permalink / raw)
To: Chunfeng Yun
Cc: Mathias Nyman, Felipe Balbi, Greg Kroah-Hartman,
Matthias Brugger, Mark Rutland, Ian Campbell, linux-kernel,
linux-arm-kernel, linux-usb, linux-mediatek, devicetree
On Wed, Jan 18, 2017 at 02:08:26PM +0800, Chunfeng Yun wrote:
> add a reference clock for compatibility
Same question here, too.
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 6/6] dt-bindings: mt8173-mtu3: add reference clock
2017-01-21 20:11 ` Rob Herring
@ 2017-01-22 1:49 ` Chunfeng Yun
2017-01-23 14:02 ` Rob Herring
0 siblings, 1 reply; 19+ messages in thread
From: Chunfeng Yun @ 2017-01-22 1:49 UTC (permalink / raw)
To: Rob Herring
Cc: Mathias Nyman, Felipe Balbi, Greg Kroah-Hartman,
Matthias Brugger, Mark Rutland, Ian Campbell, linux-kernel,
linux-arm-kernel, linux-usb, linux-mediatek, devicetree
Hi,
On Sat, 2017-01-21 at 14:11 -0600, Rob Herring wrote:
> On Wed, Jan 18, 2017 at 02:08:27PM +0800, Chunfeng Yun wrote:
> > add a reference clock for compatibility
>
> Why? This block suddenly has 2 clocks instead of 1?
In fact, there is a reference clock which comes from 26M oscillator
directly. I ignore it because it is a fixed-clock in DTS, and always
turned on for mt8173. But later, I find that I made a mistake before
when I bring up it on a new platform whose reference clock comes from
PLL, and need control it. So here add it, no matter it is a fixed-clock
or not.
>
> >
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> > .../devicetree/bindings/usb/mt8173-mtu3.txt | 10 +++++-----
> > 1 file changed, 5 insertions(+), 5 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
> > index e049d19..8c976cd 100644
> > --- a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
> > +++ b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
> > @@ -10,7 +10,7 @@ Required properties:
> > - vusb33-supply : regulator of USB avdd3.3v
> > - clocks : a list of phandle + clock-specifier pairs, one for each
> > entry in clock-names
> > - - clock-names : must contain "sys_ck" for clock of controller;
> > + - clock-names : must contain "sys_ck" and "ref_ck" for clock of controller;
> > "wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are
> > depends on "mediatek,enable-wakeup"
> > - phys : a list of phandle + phy specifier pairs
> > @@ -56,10 +56,10 @@ ssusb: usb@11271000 {
> > phys = <&phy_port0 PHY_TYPE_USB3>,
> > <&phy_port1 PHY_TYPE_USB2>;
> > power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
> > - clocks = <&topckgen CLK_TOP_USB30_SEL>,
> > + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>,
> > <&pericfg CLK_PERI_USB0>,
> > <&pericfg CLK_PERI_USB1>;
> > - clock-names = "sys_ck",
> > + clock-names = "sys_ck", "ref_ck",
> > "wakeup_deb_p0",
> > "wakeup_deb_p1";
> > vusb33-supply = <&mt6397_vusb_reg>;
> > @@ -79,8 +79,8 @@ ssusb: usb@11271000 {
> > reg-names = "mac";
> > interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
> > power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
> > - clocks = <&topckgen CLK_TOP_USB30_SEL>;
> > - clock-names = "sys_ck";
> > + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
> > + clock-names = "sys_ck", "ref_ck";
> > vusb33-supply = <&mt6397_vusb_reg>;
> > status = "disabled";
> > };
> > --
> > 1.7.9.5
> >
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 5/6] dt-bindings: mt8173-xhci: add reference clock
2017-01-21 20:12 ` Rob Herring
@ 2017-01-22 1:53 ` Chunfeng Yun
0 siblings, 0 replies; 19+ messages in thread
From: Chunfeng Yun @ 2017-01-22 1:53 UTC (permalink / raw)
To: Rob Herring
Cc: Mathias Nyman, Felipe Balbi, Greg Kroah-Hartman,
Matthias Brugger, Mark Rutland, Ian Campbell, linux-kernel,
linux-arm-kernel, linux-usb, linux-mediatek, devicetree
On Sat, 2017-01-21 at 14:12 -0600, Rob Herring wrote:
> On Wed, Jan 18, 2017 at 02:08:26PM +0800, Chunfeng Yun wrote:
> > add a reference clock for compatibility
>
> Same question here, too.
The reason is the same as mt8173-mtu3
thanks a lot
>
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 6/6] dt-bindings: mt8173-mtu3: add reference clock
2017-01-22 1:49 ` Chunfeng Yun
@ 2017-01-23 14:02 ` Rob Herring
2017-02-06 7:06 ` Chunfeng Yun
0 siblings, 1 reply; 19+ messages in thread
From: Rob Herring @ 2017-01-23 14:02 UTC (permalink / raw)
To: Chunfeng Yun
Cc: Mathias Nyman, Felipe Balbi, Greg Kroah-Hartman,
Matthias Brugger, Mark Rutland, Ian Campbell, linux-kernel,
linux-arm-kernel, Linux USB List, linux-mediatek, devicetree
On Sat, Jan 21, 2017 at 7:49 PM, Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
> Hi,
>
> On Sat, 2017-01-21 at 14:11 -0600, Rob Herring wrote:
>> On Wed, Jan 18, 2017 at 02:08:27PM +0800, Chunfeng Yun wrote:
>> > add a reference clock for compatibility
>>
>> Why? This block suddenly has 2 clocks instead of 1?
> In fact, there is a reference clock which comes from 26M oscillator
> directly. I ignore it because it is a fixed-clock in DTS, and always
> turned on for mt8173. But later, I find that I made a mistake before
> when I bring up it on a new platform whose reference clock comes from
> PLL, and need control it. So here add it, no matter it is a fixed-clock
> or not.
Add this explanation to the changelog.
Rob
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 2/6] usb: mtu3: add reference clock
2017-01-20 2:20 ` Chunfeng Yun
@ 2017-01-24 23:23 ` Matthias Brugger
2017-02-06 7:03 ` Chunfeng Yun
0 siblings, 1 reply; 19+ messages in thread
From: Matthias Brugger @ 2017-01-24 23:23 UTC (permalink / raw)
To: Chunfeng Yun
Cc: Mathias Nyman, Felipe Balbi, Greg Kroah-Hartman, Rob Herring,
Mark Rutland, Ian Campbell, linux-kernel, linux-arm-kernel,
linux-usb, linux-mediatek, devicetree
On 01/20/2017 03:20 AM, Chunfeng Yun wrote:
> On Thu, 2017-01-19 at 13:22 +0100, Matthias Brugger wrote:
>>
>> On 18/01/17 07:08, Chunfeng Yun wrote:
>>> usually, the reference clock comes from 26M oscillator directly,
>>> but some SoCs are not, add it for compatibility.
>>>
>>> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
>>> ---
>>> drivers/usb/mtu3/mtu3.h | 1 +
>>> drivers/usb/mtu3/mtu3_plat.c | 21 +++++++++++++++++++--
>>> 2 files changed, 20 insertions(+), 2 deletions(-)
> [...]
>>> @@ -154,6 +162,7 @@ static int ssusb_rscs_init(struct ssusb_mtk *ssusb)
>>> static void ssusb_rscs_exit(struct ssusb_mtk *ssusb)
>>> {
>>> clk_disable_unprepare(ssusb->sys_clk);
>>> + clk_disable_unprepare(ssusb->ref_clk);
>>> regulator_disable(ssusb->vusb33);
>>> ssusb_phy_power_off(ssusb);
>>> ssusb_phy_exit(ssusb);
>>> @@ -216,6 +225,12 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb)
>>> return PTR_ERR(ssusb->sys_clk);
>>> }
>>>
>>> + ssusb->ref_clk = devm_clk_get(dev, "ref_ck");
>>> + if (IS_ERR(ssusb->ref_clk)) {
>>> + dev_err(dev, "failed to get ref clock\n");
>>> + return PTR_ERR(ssusb->ref_clk);
>>> + }
>>> +
>>
>> That would break older dts bindings, right?
> Yes, So I send a new patch for the related dts. Maybe it's not a
> problem, only one dts file need be updated currently.
>
>> ref_ck must be optional for the code.
> I tend to make it be optional for the dts, but not for the code.
> There are some "fixed-clock" which can be treated as dummy ones, and if
> a clock is really optional, we can use one fixed-clock in dts, and keep
> the code simple.
> In fact, the reference clock is essential for usb controller.
Well the thing is that there are devices in the field with an older dtb
which would break on a newer kernel. That's why we need to make it work
with the old dtb in the code as well.
Regards,
Matthias
>>
>> Regards,
>> Matthias
>
>
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 2/6] usb: mtu3: add reference clock
2017-01-24 23:23 ` Matthias Brugger
@ 2017-02-06 7:03 ` Chunfeng Yun
0 siblings, 0 replies; 19+ messages in thread
From: Chunfeng Yun @ 2017-02-06 7:03 UTC (permalink / raw)
To: Matthias Brugger
Cc: Mathias Nyman, Felipe Balbi, Greg Kroah-Hartman, Rob Herring,
Mark Rutland, Ian Campbell, linux-kernel, linux-arm-kernel,
linux-usb, linux-mediatek, devicetree
On Wed, 2017-01-25 at 00:23 +0100, Matthias Brugger wrote:
>
> On 01/20/2017 03:20 AM, Chunfeng Yun wrote:
> > On Thu, 2017-01-19 at 13:22 +0100, Matthias Brugger wrote:
> >>
> >> On 18/01/17 07:08, Chunfeng Yun wrote:
> >>> usually, the reference clock comes from 26M oscillator directly,
> >>> but some SoCs are not, add it for compatibility.
> >>>
> >>> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> >>> ---
> >>> drivers/usb/mtu3/mtu3.h | 1 +
> >>> drivers/usb/mtu3/mtu3_plat.c | 21 +++++++++++++++++++--
> >>> 2 files changed, 20 insertions(+), 2 deletions(-)
> > [...]
> >>> @@ -154,6 +162,7 @@ static int ssusb_rscs_init(struct ssusb_mtk *ssusb)
> >>> static void ssusb_rscs_exit(struct ssusb_mtk *ssusb)
> >>> {
> >>> clk_disable_unprepare(ssusb->sys_clk);
> >>> + clk_disable_unprepare(ssusb->ref_clk);
> >>> regulator_disable(ssusb->vusb33);
> >>> ssusb_phy_power_off(ssusb);
> >>> ssusb_phy_exit(ssusb);
> >>> @@ -216,6 +225,12 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb)
> >>> return PTR_ERR(ssusb->sys_clk);
> >>> }
> >>>
> >>> + ssusb->ref_clk = devm_clk_get(dev, "ref_ck");
> >>> + if (IS_ERR(ssusb->ref_clk)) {
> >>> + dev_err(dev, "failed to get ref clock\n");
> >>> + return PTR_ERR(ssusb->ref_clk);
> >>> + }
> >>> +
> >>
> >> That would break older dts bindings, right?
> > Yes, So I send a new patch for the related dts. Maybe it's not a
> > problem, only one dts file need be updated currently.
> >
> >> ref_ck must be optional for the code.
> > I tend to make it be optional for the dts, but not for the code.
> > There are some "fixed-clock" which can be treated as dummy ones, and if
> > a clock is really optional, we can use one fixed-clock in dts, and keep
> > the code simple.
> > In fact, the reference clock is essential for usb controller.
>
> Well the thing is that there are devices in the field with an older dtb
> which would break on a newer kernel. That's why we need to make it work
> with the old dtb in the code as well.
>
Happy Chinese New Year!
Ok, I will make it optional.
Thanks and sorry for later reply.
> Regards,
> Matthias
>
> >>
> >> Regards,
> >> Matthias
> >
> >
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 6/6] dt-bindings: mt8173-mtu3: add reference clock
2017-01-23 14:02 ` Rob Herring
@ 2017-02-06 7:06 ` Chunfeng Yun
0 siblings, 0 replies; 19+ messages in thread
From: Chunfeng Yun @ 2017-02-06 7:06 UTC (permalink / raw)
To: Rob Herring
Cc: Mathias Nyman, Felipe Balbi, Greg Kroah-Hartman,
Matthias Brugger, Mark Rutland, Ian Campbell, linux-kernel,
linux-arm-kernel, Linux USB List, linux-mediatek, devicetree
On Mon, 2017-01-23 at 08:02 -0600, Rob Herring wrote:
> On Sat, Jan 21, 2017 at 7:49 PM, Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
> > Hi,
> >
> > On Sat, 2017-01-21 at 14:11 -0600, Rob Herring wrote:
> >> On Wed, Jan 18, 2017 at 02:08:27PM +0800, Chunfeng Yun wrote:
> >> > add a reference clock for compatibility
> >>
> >> Why? This block suddenly has 2 clocks instead of 1?
> > In fact, there is a reference clock which comes from 26M oscillator
> > directly. I ignore it because it is a fixed-clock in DTS, and always
> > turned on for mt8173. But later, I find that I made a mistake before
> > when I bring up it on a new platform whose reference clock comes from
> > PLL, and need control it. So here add it, no matter it is a fixed-clock
> > or not.
>
> Add this explanation to the changelog.
>
Happy Chinese New Year!
Ok, I'll add it.
Thanks and sorry for later reply.
> Rob
^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2017-02-06 7:09 UTC | newest]
Thread overview: 19+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-01-18 6:08 [PATCH 1/6] usb: mtu3: get resources that cause deferred probe earlier Chunfeng Yun
2017-01-18 6:08 ` [PATCH 2/6] usb: mtu3: add reference clock Chunfeng Yun
2017-01-19 12:22 ` Matthias Brugger
2017-01-20 2:20 ` Chunfeng Yun
2017-01-24 23:23 ` Matthias Brugger
2017-02-06 7:03 ` Chunfeng Yun
2017-01-18 6:08 ` [PATCH 3/6] usb: xhci-mtk: " Chunfeng Yun
2017-01-18 6:08 ` [PATCH 4/6] arm64: dts: mt8173: add reference clock for usb Chunfeng Yun
2017-01-19 9:37 ` Greg Kroah-Hartman
2017-01-19 12:23 ` Matthias Brugger
2017-01-18 6:08 ` [PATCH 5/6] dt-bindings: mt8173-xhci: add reference clock Chunfeng Yun
2017-01-21 20:10 ` Rob Herring
2017-01-21 20:12 ` Rob Herring
2017-01-22 1:53 ` Chunfeng Yun
2017-01-18 6:08 ` [PATCH 6/6] dt-bindings: mt8173-mtu3: " Chunfeng Yun
2017-01-21 20:11 ` Rob Herring
2017-01-22 1:49 ` Chunfeng Yun
2017-01-23 14:02 ` Rob Herring
2017-02-06 7:06 ` Chunfeng Yun
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).