[PATCH v2 00/15] ARM: dts: i.MX6: Add lcdif/sound nodes on Engicam SOMs

[PATCH v2 00/15] ARM: dts: i.MX6: Add lcdif/sound nodes on Engicam SOMs

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

This patchset, add support for backlight, lcdif, touchscreen,
sound card and related codec and can nodes all Engicam SOM's
which are supporting mainline as of now.

Jagan Teki (15):
  ARM: dts: imx6ul-geam: Add backlight support for lcdif
  ARM: dts: imx6ul-isiot: Add backlight support for lcdif
  ARM: dts: imx6ul-isiot: Add imx6ul-isiot-common.dtsi
  ARM: dts: imx6ul-isiot: Add i2c nodes
  ARM: dts: imx6ul-isiot-common: Add touchscreen node
  ARM: dts: imx6ul-[geam|isiot]: Add sai2 node
  ARM: dts: imx6ul-isiot: Add Sound card with codec node
  ARM: dts: imx6ul-geam: Add Sound card with codec node
  ARM: dts: imx6qdl-icore: Add Sound card with codec node
  ARM: dts: imx6dl-icore-rqs: Add sgtl5000 codec node
  ARM: dts: imx6qdl-icore-rqs: Replace codec 'lable: node@addr'
  ARM: dts: imx6dl-icore: Add LVDS support
  ARM: dts: imx6dl-icore: Add touchscreen node
  ARM: dts: imx6qdl-icore-rqs: Add CAN nodes
  ARM: dts: imx6ul-isiot: Add FEC node support

 arch/arm/boot/dts/imx6dl-icore-rqs.dts     |  19 ++++
 arch/arm/boot/dts/imx6dl-icore.dts         |  45 +++++++++
 arch/arm/boot/dts/imx6q-icore-ofcap10.dts  |  11 +++
 arch/arm/boot/dts/imx6q-icore-ofcap12.dts  |  11 +++
 arch/arm/boot/dts/imx6q-icore-rqs.dts      |  21 ++--
 arch/arm/boot/dts/imx6q-icore.dts          |  11 +++
 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi   |  39 ++++++++
 arch/arm/boot/dts/imx6qdl-icore.dtsi       |  37 +++++++
 arch/arm/boot/dts/imx6ul-geam-kit.dts      |  12 +++
 arch/arm/boot/dts/imx6ul-geam.dtsi         |  56 +++++++++++
 arch/arm/boot/dts/imx6ul-isiot-common.dtsi | 151 +++++++++++++++++++++++++++++
 arch/arm/boot/dts/imx6ul-isiot-emmc.dts    |   1 +
 arch/arm/boot/dts/imx6ul-isiot-nand.dts    |   1 +
 arch/arm/boot/dts/imx6ul-isiot.dtsi        | 135 ++++++++++++++++++++++++++
 14 files changed, 537 insertions(+), 13 deletions(-)
 create mode 100644 arch/arm/boot/dts/imx6ul-isiot-common.dtsi

-- 
1.9.1

[PATCH v2 01/15] ARM: dts: imx6ul-geam: Add backlight support for lcdif

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

This patch add support for lcdif backlight on GEAM6UL
variant boards.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- none

 arch/arm/boot/dts/imx6ul-geam.dtsi | 29 +++++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-geam.dtsi b/arch/arm/boot/dts/imx6ul-geam.dtsi
index 940aef6..ee5220c 100644
--- a/arch/arm/boot/dts/imx6ul-geam.dtsi
+++ b/arch/arm/boot/dts/imx6ul-geam.dtsi
@@ -49,6 +49,23 @@
 		reg = <0x80000000 0x08000000>;
 	};
 
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm8 0 100000>;
+		brightness-levels = < 0  1  2  3  4  5  6  7  8  9
+				     10 11 12 13 14 15 16 17 18 19
+				     20 21 22 23 24 25 26 27 28 29
+				     30 31 32 33 34 35 36 37 38 39
+				     40 41 42 43 44 45 46 47 48 49
+				     50 51 52 53 54 55 56 57 58 59
+				     60 61 62 63 64 65 66 67 68 69
+				     70 71 72 73 74 75 76 77 78 79
+				     80 81 82 83 84 85 86 87 88 89
+				     90 91 92 93 94 95 96 97 98 99
+				    100>;
+		default-brightness-level = <100>;
+	};
+
 	chosen {
 		stdout-path = &uart1;
 	};
@@ -143,6 +160,12 @@
 	display = <&display0>;
 };
 
+&pwm8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm8>;
+	status = "okay";
+};
+
 &tsc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_tsc>;
@@ -290,6 +313,12 @@
 		>;
 	};
 
+	pinctrl_pwm8: pwm8grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_ER__PWM8_OUT   0x110b0
+		>;
+	};
+
 	pinctrl_tsc: tscgrp {
 		fsl,pin = <
 			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0xb0
-- 
1.9.1

[PATCH v2 02/15] ARM: dts: imx6ul-isiot: Add backlight support for lcdif

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

This patch add support for lcdif backlight on Is.IoT MX6UL
variant boards.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- none

 arch/arm/boot/dts/imx6ul-isiot.dtsi | 29 +++++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-isiot.dtsi b/arch/arm/boot/dts/imx6ul-isiot.dtsi
index 0b43699..5ccc3df 100644
--- a/arch/arm/boot/dts/imx6ul-isiot.dtsi
+++ b/arch/arm/boot/dts/imx6ul-isiot.dtsi
@@ -52,6 +52,29 @@
 	chosen {
 		stdout-path = &uart1;
 	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm8 0 100000>;
+		brightness-levels = < 0  1  2  3  4  5  6  7  8  9
+				     10 11 12 13 14 15 16 17 18 19
+				     20 21 22 23 24 25 26 27 28 29
+				     30 31 32 33 34 35 36 37 38 39
+				     40 41 42 43 44 45 46 47 48 49
+				     50 51 52 53 54 55 56 57 58 59
+				     60 61 62 63 64 65 66 67 68 69
+				     70 71 72 73 74 75 76 77 78 79
+				     80 81 82 83 84 85 86 87 88 89
+				     90 91 92 93 94 95 96 97 98 99
+				    100>;
+		default-brightness-level = <100>;
+	};
+};
+
+&pwm8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm8>;
+	status = "okay";
 };
 
 &uart1 {
@@ -72,6 +95,12 @@
 };
 
 &iomuxc {
+	pinctrl_pwm8: pwm8grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_ER__PWM8_OUT   0x110b0
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
-- 
1.9.1

[PATCH v2 03/15] ARM: dts: imx6ul-isiot: Add imx6ul-isiot-common.dtsi

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

lcdif nodes are differ wrt specific LCD connected on Is.IoT MX6UL
module, so create separate file 'imx6ul-isiot-common.dtsi' for common
lcdif node structure and include the same on respective dts.

More common nodes will add in future patches.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- none

 arch/arm/boot/dts/imx6ul-isiot-common.dtsi | 107 +++++++++++++++++++++++++++++
 arch/arm/boot/dts/imx6ul-isiot-emmc.dts    |   1 +
 arch/arm/boot/dts/imx6ul-isiot-nand.dts    |   1 +
 3 files changed, 109 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6ul-isiot-common.dtsi

diff --git a/arch/arm/boot/dts/imx6ul-isiot-common.dtsi b/arch/arm/boot/dts/imx6ul-isiot-common.dtsi
new file mode 100644
index 0000000..9660e20
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-isiot-common.dtsi
@@ -0,0 +1,107 @@
+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcdif_dat
+		     &pinctrl_lcdif_ctrl>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display {
+		bits-per-pixel = <16>;
+		bus-width = <18>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <28000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hfront-porch = <30>;
+				hback-porch = <30>;
+				hsync-len = <64>;
+				vback-porch = <5>;
+				vfront-porch = <5>;
+				vsync-len = <20>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_lcdif_ctrl: lcdifctrlgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__LCDIF_CLK	    0x79
+			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE  0x79
+			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC    0x79
+			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC    0x79
+		>;
+	};
+
+	pinctrl_lcdif_dat: lcdifdatgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00  0x79
+			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01  0x79
+			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02  0x79
+			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03  0x79
+			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04  0x79
+			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05  0x79
+			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06  0x79
+			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07  0x79
+			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08  0x79
+			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09  0x79
+			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10  0x79
+			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11  0x79
+			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12  0x79
+			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13  0x79
+			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14  0x79
+			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15  0x79
+			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16  0x79
+			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17  0x79
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-isiot-emmc.dts b/arch/arm/boot/dts/imx6ul-isiot-emmc.dts
index f5b4228..73a1d0f 100644
--- a/arch/arm/boot/dts/imx6ul-isiot-emmc.dts
+++ b/arch/arm/boot/dts/imx6ul-isiot-emmc.dts
@@ -43,6 +43,7 @@
 /dts-v1/;
 
 #include "imx6ul-isiot.dtsi"
+#include "imx6ul-isiot-common.dtsi"
 
 / {
 	model = "Engicam Is.IoT MX6UL eMMC Starter kit";
diff --git a/arch/arm/boot/dts/imx6ul-isiot-nand.dts b/arch/arm/boot/dts/imx6ul-isiot-nand.dts
index de15e1c..da29a86 100644
--- a/arch/arm/boot/dts/imx6ul-isiot-nand.dts
+++ b/arch/arm/boot/dts/imx6ul-isiot-nand.dts
@@ -43,6 +43,7 @@
 /dts-v1/;
 
 #include "imx6ul-isiot.dtsi"
+#include "imx6ul-isiot-common.dtsi"
 
 / {
 	model = "Engicam Is.IoT MX6UL NAND Starter kit";
-- 
1.9.1

[PATCH v2 04/15] ARM: dts: imx6ul-isiot: Add i2c nodes

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

Add support for i2c nodes i2c1 and i2c2 on Is.IoT MX6UL
eMMC variant boards.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- none

 arch/arm/boot/dts/imx6ul-isiot.dtsi | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-isiot.dtsi b/arch/arm/boot/dts/imx6ul-isiot.dtsi
index 5ccc3df..4697a04 100644
--- a/arch/arm/boot/dts/imx6ul-isiot.dtsi
+++ b/arch/arm/boot/dts/imx6ul-isiot.dtsi
@@ -71,6 +71,20 @@
 	};
 };
 
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock_frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
 &pwm8 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm8>;
@@ -95,6 +109,20 @@
 };
 
 &iomuxc {
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
+			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__I2C2_SCL 0x4001b8b0
+			MX6UL_PAD_GPIO1_IO01__I2C2_SDA 0x4001b8b0
+		>;
+	};
+
 	pinctrl_pwm8: pwm8grp {
 		fsl,pins = <
 			MX6UL_PAD_ENET1_RX_ER__PWM8_OUT   0x110b0
-- 
1.9.1

[PATCH v2 05/15] ARM: dts: imx6ul-isiot-common: Add touchscreen node

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

Add touchscreen node as i2c1 slave device on Engicam Is.IoT MX6UL
modules, the touchscreen controlled 'st,stmpe-ts' connected via
i2c with st,stmpe811 mfd interface.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- Fix commit message s/mfb/mfd
- Use proper [label:] node-name[@unit-address] for mfd device 
- Use pinctrl-names as pinctrl_stmpe instead of pinctrl_stmpe_ts
- Use proper [label:] node-name[@unit-address] for stmpe_touchscreen

 arch/arm/boot/dts/imx6ul-isiot-common.dtsi | 34 ++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-isiot-common.dtsi b/arch/arm/boot/dts/imx6ul-isiot-common.dtsi
index 9660e20..827f0dc 100644
--- a/arch/arm/boot/dts/imx6ul-isiot-common.dtsi
+++ b/arch/arm/boot/dts/imx6ul-isiot-common.dtsi
@@ -40,6 +40,34 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
+&i2c1 {
+	stmpe811: gpio-expander@44 {
+		compatible = "st,stmpe811";
+		reg = <0x44>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_stmpe>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		stmpe: touchscreen {
+			compatible = "st,stmpe-ts";
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <1>;
+			st,touch-det-delay = <2>;
+			st,settling = <2>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
+		};
+	};
+};
+
 &lcdif {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lcdif_dat
@@ -104,4 +132,10 @@
 			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17  0x79
 		>;
 	};
+
+	pinctrl_stmpe: stmpegrp  {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x1b0b0
+		>;
+	};
 };
-- 
1.9.1

[PATCH v2 06/15] ARM: dts: imx6ul-[geam|isiot]: Add sai2 node

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

Add Synchronous Audio Interface(SAI) node for Engicam GEAM6UL
and Is.IoT MX6UL variant module boards.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- none

 arch/arm/boot/dts/imx6ul-geam.dtsi  | 16 ++++++++++++++++
 arch/arm/boot/dts/imx6ul-isiot.dtsi | 16 ++++++++++++++++
 2 files changed, 32 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-geam.dtsi b/arch/arm/boot/dts/imx6ul-geam.dtsi
index ee5220c..eb94d95 100644
--- a/arch/arm/boot/dts/imx6ul-geam.dtsi
+++ b/arch/arm/boot/dts/imx6ul-geam.dtsi
@@ -172,6 +172,12 @@
 	xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
 };
 
+&sai2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	status = "okay";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
@@ -328,6 +334,16 @@
 		>;
 	};
 
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x130b0
+			MX6UL_PAD_JTAG_TMS__CCM_CLKO1		0x4001b031
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x120b0
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
diff --git a/arch/arm/boot/dts/imx6ul-isiot.dtsi b/arch/arm/boot/dts/imx6ul-isiot.dtsi
index 4697a04..ea30380 100644
--- a/arch/arm/boot/dts/imx6ul-isiot.dtsi
+++ b/arch/arm/boot/dts/imx6ul-isiot.dtsi
@@ -91,6 +91,12 @@
 	status = "okay";
 };
 
+&sai2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	status = "okay";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
@@ -129,6 +135,16 @@
 		>;
 	};
 
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x130b0
+			MX6UL_PAD_JTAG_TMS__CCM_CLKO1		0x4001b031
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x120b0
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
-- 
1.9.1

[PATCH v2 07/15] ARM: dts: imx6ul-isiot: Add Sound card with codec node

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

Add support for Sound card and related codec(via i2c1) nodes
on Engicam Is.IoT MX6UL variant module boards.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- Use proper [label:] node-name[@unit-address] for codec
- Remove incorrect codec property 'wlf,shared-lrclk'
- Remove 'gpr' from sound card node

 arch/arm/boot/dts/imx6ul-isiot-common.dtsi | 10 ++++++++++
 arch/arm/boot/dts/imx6ul-isiot.dtsi        | 29 +++++++++++++++++++++++++++++
 2 files changed, 39 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-isiot-common.dtsi b/arch/arm/boot/dts/imx6ul-isiot-common.dtsi
index 827f0dc..15dcf5f 100644
--- a/arch/arm/boot/dts/imx6ul-isiot-common.dtsi
+++ b/arch/arm/boot/dts/imx6ul-isiot-common.dtsi
@@ -41,6 +41,16 @@
  */
 
 &i2c1 {
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		clocks = <&clks IMX6UL_CLK_OSC>;
+		clock-names = "mclk";
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+		VDDD-supply = <&reg_1p8v>;
+	};
+
 	stmpe811: gpio-expander@44 {
 		compatible = "st,stmpe811";
 		reg = <0x44>;
diff --git a/arch/arm/boot/dts/imx6ul-isiot.dtsi b/arch/arm/boot/dts/imx6ul-isiot.dtsi
index ea30380..9648de9 100644
--- a/arch/arm/boot/dts/imx6ul-isiot.dtsi
+++ b/arch/arm/boot/dts/imx6ul-isiot.dtsi
@@ -69,6 +69,35 @@
 				    100>;
 		default-brightness-level = <100>;
 	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "imx6ul-isiot-sgtl5000";
+		cpu-dai = <&sai2>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+	};
 };
 
 &i2c1 {
-- 
1.9.1

[PATCH v2 08/15] ARM: dts: imx6ul-geam: Add Sound card with codec node

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

Add support for Sound card and related codec(via i2c1) nodes
on Engicam GEAM6UL variant module boards.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- Use proper [label:] node-name[@unit-address] for codec
- Remove incorrect codec property 'wlf,shared-lrclk'
- Remove 'gpr' from sound card node

 arch/arm/boot/dts/imx6ul-geam-kit.dts | 12 ++++++++++++
 arch/arm/boot/dts/imx6ul-geam.dtsi    | 11 +++++++++++
 2 files changed, 23 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-geam-kit.dts b/arch/arm/boot/dts/imx6ul-geam-kit.dts
index 142e60c..02edcba 100644
--- a/arch/arm/boot/dts/imx6ul-geam-kit.dts
+++ b/arch/arm/boot/dts/imx6ul-geam-kit.dts
@@ -58,6 +58,18 @@
 	status = "okay";
 };
 
+&i2c1 {
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		clocks = <&clks IMX6UL_CLK_OSC>;
+		clock-names = "mclk";
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+		VDDD-supply = <&reg_1p8v>;
+	};
+};
+
 &lcdif {
 	display = <&display0>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6ul-geam.dtsi b/arch/arm/boot/dts/imx6ul-geam.dtsi
index eb94d95..1ffca2b 100644
--- a/arch/arm/boot/dts/imx6ul-geam.dtsi
+++ b/arch/arm/boot/dts/imx6ul-geam.dtsi
@@ -87,6 +87,17 @@
 		regulator-always-on;
 		regulator-boot-on;
 	};
+
+	sound {
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "imx6q-geam-sgtl5000";
+		cpu-dai = <&sai2>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+	};
 };
 
 &can1 {
-- 
1.9.1

[PATCH v2 09/15] ARM: dts: imx6qdl-icore: Add Sound card with codec node

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

Add support for Sound card and related codec(via i2c1) nodes
on below Engicam module boards.
- i.CoreM6 DualLite/Solo Starter kit
- i.CoreM6 Quad/Dual Starter kit
- i.CoreM6 Quad/Dual OpenFrame Cap touch 10.1
- i.CoreM6 Quad/Dual OpenFrame Cap touch 12.3

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- Use proper [label:] node-name[@unit-address] for codec

 arch/arm/boot/dts/imx6dl-icore.dts        | 11 +++++++++
 arch/arm/boot/dts/imx6q-icore-ofcap10.dts | 11 +++++++++
 arch/arm/boot/dts/imx6q-icore-ofcap12.dts | 11 +++++++++
 arch/arm/boot/dts/imx6q-icore.dts         | 11 +++++++++
 arch/arm/boot/dts/imx6qdl-icore.dtsi      | 37 +++++++++++++++++++++++++++++++
 5 files changed, 81 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-icore.dts b/arch/arm/boot/dts/imx6dl-icore.dts
index 6de83c7..0562ce4 100644
--- a/arch/arm/boot/dts/imx6dl-icore.dts
+++ b/arch/arm/boot/dts/imx6dl-icore.dts
@@ -57,3 +57,14 @@
 &can2 {
 	status = "okay";
 };
+
+&i2c3 {
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+		VDDD-supply = <&reg_1p8v>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-icore-ofcap10.dts b/arch/arm/boot/dts/imx6q-icore-ofcap10.dts
index 49b60ca..f63b87f 100644
--- a/arch/arm/boot/dts/imx6q-icore-ofcap10.dts
+++ b/arch/arm/boot/dts/imx6q-icore-ofcap10.dts
@@ -50,6 +50,17 @@
 	compatible = "engicam,imx6-icore", "fsl,imx6q";
 };
 
+&i2c3 {
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+		VDDD-supply = <&reg_1p8v>;
+	};
+};
+
 &ldb {
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/imx6q-icore-ofcap12.dts b/arch/arm/boot/dts/imx6q-icore-ofcap12.dts
index 9e230f5..68ca828 100644
--- a/arch/arm/boot/dts/imx6q-icore-ofcap12.dts
+++ b/arch/arm/boot/dts/imx6q-icore-ofcap12.dts
@@ -50,6 +50,17 @@
 	compatible = "engicam,imx6-icore", "fsl,imx6q";
 };
 
+&i2c3 {
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+		VDDD-supply = <&reg_1p8v>;
+	};
+};
+
 &ldb {
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/imx6q-icore.dts b/arch/arm/boot/dts/imx6q-icore.dts
index 5613dd9..1ae7294 100644
--- a/arch/arm/boot/dts/imx6q-icore.dts
+++ b/arch/arm/boot/dts/imx6q-icore.dts
@@ -67,6 +67,17 @@
 	};
 };
 
+&i2c3 {
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+		VDDD-supply = <&reg_1p8v>;
+	};
+};
+
 &ldb {
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/imx6qdl-icore.dtsi b/arch/arm/boot/dts/imx6qdl-icore.dtsi
index 56d0c5d..09600eb 100644
--- a/arch/arm/boot/dts/imx6qdl-icore.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-icore.dtsi
@@ -55,6 +55,25 @@
 		default-brightness-level = <7>;
 	};
 
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+
+	reg_2p5v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "3P3V";
@@ -87,6 +106,20 @@
 		#clock-cells = <0>;
 		clock-frequency = <25000000>;  /* 25MHz for example */
 	};
+
+	sound {
+		compatible = "fsl,imx6-icore-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx6q-icore-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <4>;
+	};
 };
 
 &can1 {
@@ -149,6 +182,10 @@
 	status = "okay";
 };
 
+&ssi1 {
+	status = "okay";
+};
+
 &uart4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart4>;
-- 
1.9.1

[PATCH v2 10/15] ARM: dts: imx6dl-icore-rqs: Add sgtl5000 codec node

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

- Moved sound card node on imx6qdl-icore-rqs.dtsi
- Added codec node in imx6dl-icore-rqs from imx6q-icore-rqs

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- Newly added patch

 arch/arm/boot/dts/imx6dl-icore-rqs.dts   | 11 +++++++++++
 arch/arm/boot/dts/imx6q-icore-rqs.dts    | 13 -------------
 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 13 +++++++++++++
 3 files changed, 24 insertions(+), 13 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-icore-rqs.dts b/arch/arm/boot/dts/imx6dl-icore-rqs.dts
index cf42c2f..5b4c14c 100644
--- a/arch/arm/boot/dts/imx6dl-icore-rqs.dts
+++ b/arch/arm/boot/dts/imx6dl-icore-rqs.dts
@@ -49,3 +49,14 @@
 	model = "Engicam i.CoreM6 DualLite/Solo RQS Starter Kit";
 	compatible = "engicam,imx6-icore-rqs", "fsl,imx6dl";
 };
+
+&i2c3 {
+	codec: sgtl5000@0a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+		VDDD-supply = <&reg_1p8v>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/imx6q-icore-rqs.dts
index e451b4c..441a28e5 100644
--- a/arch/arm/boot/dts/imx6q-icore-rqs.dts
+++ b/arch/arm/boot/dts/imx6q-icore-rqs.dts
@@ -47,19 +47,6 @@
 / {
 	model = "Engicam i.CoreM6 Quad/Dual RQS Starter Kit";
 	compatible = "engicam,imx6-icore-rqs", "fsl,imx6q";
-
-	sound {
-		compatible = "fsl,imx-audio-sgtl5000";
-		model = "imx-audio-sgtl5000";
-		ssi-controller = <&ssi1>;
-		audio-codec = <&codec>;
-		audio-routing =
-			"MIC_IN", "Mic Jack",
-			"Mic Jack", "Mic Bias",
-			"Headphone Jack", "HP_OUT";
-		mux-int-port = <1>;
-		mux-ext-port = <4>;
-	};
 };
 
 &i2c3 {
diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
index 5fab5be..4032d38 100644
--- a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
@@ -118,6 +118,19 @@
 		clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>;
 		clock-names = "refclk";
 	};
+
+	sound {
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "imx-audio-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <4>;
+	};
 };
 
 &clks {
-- 
1.9.1

[PATCH v2 11/15] ARM: dts: imx6qdl-icore-rqs: Replace codec 'lable: node@addr'

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

According to devicetree specification from ePAPER v1.1
[label:] node-name[@unit-address] { };

label: should be human readable string describing a device.
node-name: The name of a node should be somewhat generic,
reflecting the function of the device and not its
unit-address: match the first address specified in the
reg property of the node and shouldn't have leading zeros.

So replaced
codec: sgtl5000@0a => sgtl5000: codec@a

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- Newly added patch

 arch/arm/boot/dts/imx6dl-icore-rqs.dts   | 2 +-
 arch/arm/boot/dts/imx6q-icore-rqs.dts    | 2 +-
 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-icore-rqs.dts b/arch/arm/boot/dts/imx6dl-icore-rqs.dts
index 5b4c14c..053e7cb 100644
--- a/arch/arm/boot/dts/imx6dl-icore-rqs.dts
+++ b/arch/arm/boot/dts/imx6dl-icore-rqs.dts
@@ -51,7 +51,7 @@
 };
 
 &i2c3 {
-	codec: sgtl5000@0a {
+	sgtl5000: codec@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/imx6q-icore-rqs.dts
index 441a28e5..d45e4f5 100644
--- a/arch/arm/boot/dts/imx6q-icore-rqs.dts
+++ b/arch/arm/boot/dts/imx6q-icore-rqs.dts
@@ -50,7 +50,7 @@
 };
 
 &i2c3 {
-	codec: sgtl5000@0a {
+	sgtl5000: codec@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
index 4032d38..d24e531 100644
--- a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
@@ -123,7 +123,7 @@
 		compatible = "fsl,imx-audio-sgtl5000";
 		model = "imx-audio-sgtl5000";
 		ssi-controller = <&ssi1>;
-		audio-codec = <&codec>;
+		audio-codec = <&sgtl5000>;
 		audio-routing =
 			"MIC_IN", "Mic Jack",
 			"Mic Jack", "Mic Bias",
-- 
1.9.1

[PATCH v2 12/15] ARM: dts: imx6dl-icore: Add LVDS support

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

Add LVDS display support for OpenFrame Capacitive touch 7 inc
display which is supported by Engicam i.CoreM6 DualLite/Solo Starter Kit.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- none

 arch/arm/boot/dts/imx6dl-icore.dts | 25 +++++++++++++++++++++++++
 1 file changed, 25 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-icore.dts b/arch/arm/boot/dts/imx6dl-icore.dts
index 0562ce4..ea9ab05 100644
--- a/arch/arm/boot/dts/imx6dl-icore.dts
+++ b/arch/arm/boot/dts/imx6dl-icore.dts
@@ -68,3 +68,28 @@
 		VDDD-supply = <&reg_1p8v>;
 	};
 };
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <18>;
+		status = "okay";
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <60000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <30>;
+				hfront-porch = <30>;
+				vback-porch = <5>;
+				vfront-porch = <5>;
+				hsync-len = <64>;
+				vsync-len = <20>;
+			};
+		};
+	};
+};
-- 
1.9.1

[PATCH v2 13/15] ARM: dts: imx6dl-icore: Add touchscreen node

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

max11801 touchscreen on Engicam iCoreM6 DualLite/Solo module is
connected via i2c1, so add max11801: touchscreen@48 on i2c1.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- none

 arch/arm/boot/dts/imx6dl-icore.dts | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-icore.dts b/arch/arm/boot/dts/imx6dl-icore.dts
index ea9ab05..27f37cd 100644
--- a/arch/arm/boot/dts/imx6dl-icore.dts
+++ b/arch/arm/boot/dts/imx6dl-icore.dts
@@ -58,6 +58,15 @@
 	status = "okay";
 };
 
+&i2c1 {
+	max11801: touchscreen@48 {
+		compatible = "maxim,max11801";
+		reg = <0x48>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
 &i2c3 {
 	sgtl5000: codec@a {
 		compatible = "fsl,sgtl5000";
-- 
1.9.1

[PATCH v2 14/15] ARM: dts: imx6qdl-icore-rqs: Add CAN nodes

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

Add support for can1 and can2 nodes on Engicam i.CoreM6 RQS
QDL module boards.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- s/flexcan/can
- s/pinctrl_flexcan/pinctrl_can 

 arch/arm/boot/dts/imx6dl-icore-rqs.dts   |  8 ++++++++
 arch/arm/boot/dts/imx6q-icore-rqs.dts    |  8 ++++++++
 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 26 ++++++++++++++++++++++++++
 3 files changed, 42 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-icore-rqs.dts b/arch/arm/boot/dts/imx6dl-icore-rqs.dts
index 053e7cb..74335c4 100644
--- a/arch/arm/boot/dts/imx6dl-icore-rqs.dts
+++ b/arch/arm/boot/dts/imx6dl-icore-rqs.dts
@@ -60,3 +60,11 @@
 		VDDD-supply = <&reg_1p8v>;
 	};
 };
+
+&can1 {
+	status = "okay";
+};
+
+&can2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/imx6q-icore-rqs.dts
index d45e4f5..2d4539a 100644
--- a/arch/arm/boot/dts/imx6q-icore-rqs.dts
+++ b/arch/arm/boot/dts/imx6q-icore-rqs.dts
@@ -49,6 +49,14 @@
 	compatible = "engicam,imx6-icore-rqs", "fsl,imx6q";
 };
 
+&can1 {
+	status = "okay";
+};
+
+&can2 {
+	status = "okay";
+};
+
 &i2c3 {
 	sgtl5000: codec@a {
 		compatible = "fsl,sgtl5000";
diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
index d24e531..1bd3f4a 100644
--- a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
@@ -133,6 +133,18 @@
 	};
 };
 
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_3p3v>;
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	xceiver-supply = <&reg_3p3v>;
+};
+
 &clks {
 	assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>;
 	assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
@@ -284,6 +296,20 @@
 		>;
 	};
 
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b020
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b020
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b020
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b020
+		>;
+	};
+
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
-- 
1.9.1

[PATCH v2 15/15] ARM: dts: imx6ul-isiot: Add FEC node support

[Jagan Teki]

From: Jagan Teki <jagan@amarulasolutions.com>

Add support for fec1 node on Engicam Is.IoT variant boards.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- Newly added patch

 arch/arm/boot/dts/imx6ul-isiot.dtsi | 33 +++++++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-isiot.dtsi b/arch/arm/boot/dts/imx6ul-isiot.dtsi
index 9648de9..34a39c7 100644
--- a/arch/arm/boot/dts/imx6ul-isiot.dtsi
+++ b/arch/arm/boot/dts/imx6ul-isiot.dtsi
@@ -114,6 +114,24 @@
 	status = "okay";
 };
 
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+		};
+	};
+};
+
 &pwm8 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm8>;
@@ -144,6 +162,21 @@
 };
 
 &iomuxc {
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_DATA0__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET1_MDC	0x1b0b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
+			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10	0x1b0b0
+		>;
+	};
+
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
-- 
1.9.1

Re: [PATCH v2 07/15] ARM: dts: imx6ul-isiot: Add Sound card with codec node

[Shawn Guo]

On Fri, Mar 24, 2017 at 09:48:42PM +0530, Jagan Teki wrote:
> From: Jagan Teki <jagan@amarulasolutions.com>
> 
> Add support for Sound card and related codec(via i2c1) nodes
> on Engicam Is.IoT MX6UL variant module boards.
> 
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: Matteo Lisi <matteo.lisi@engicam.com>
> Cc: Michael Trimarchi <michael@amarulasolutions.com>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

<snip>

> diff --git a/arch/arm/boot/dts/imx6ul-isiot.dtsi b/arch/arm/boot/dts/imx6ul-isiot.dtsi
> index ea30380..9648de9 100644
> --- a/arch/arm/boot/dts/imx6ul-isiot.dtsi
> +++ b/arch/arm/boot/dts/imx6ul-isiot.dtsi
> @@ -69,6 +69,35 @@
>  				    100>;
>  		default-brightness-level = <100>;
>  	};
> +
> +	reg_1p8v: regulator-1p8v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "1P8V";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3P3V";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	sound {
> +		compatible = "fsl,imx-audio-sgtl5000";
> +		model = "imx6ul-isiot-sgtl5000";
> +		cpu-dai = <&sai2>;
> +		audio-codec = <&sgtl5000>;
> +		audio-routing =
> +			"MIC_IN", "Mic Jack",
> +			"Mic Jack", "Mic Bias",
> +			"Headphone Jack", "HP_OUT";
> +	};

Can you consider to use simple-audio-card bindings instead?

Shawn

>  };
>  
>  &i2c1 {
> -- 
> 1.9.1
> 

Re: [PATCH v2 10/15] ARM: dts: imx6dl-icore-rqs: Add sgtl5000 codec node

[Shawn Guo]

On Fri, Mar 24, 2017 at 09:48:45PM +0530, Jagan Teki wrote:
> From: Jagan Teki <jagan@amarulasolutions.com>
> 
> - Moved sound card node on imx6qdl-icore-rqs.dtsi
> - Added codec node in imx6dl-icore-rqs from imx6q-icore-rqs
> 
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: Matteo Lisi <matteo.lisi@engicam.com>
> Cc: Michael Trimarchi <michael@amarulasolutions.com>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> Changes for v2:
> - Newly added patch
> 
>  arch/arm/boot/dts/imx6dl-icore-rqs.dts   | 11 +++++++++++
>  arch/arm/boot/dts/imx6q-icore-rqs.dts    | 13 -------------
>  arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 13 +++++++++++++
>  3 files changed, 24 insertions(+), 13 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6dl-icore-rqs.dts b/arch/arm/boot/dts/imx6dl-icore-rqs.dts
> index cf42c2f..5b4c14c 100644
> --- a/arch/arm/boot/dts/imx6dl-icore-rqs.dts
> +++ b/arch/arm/boot/dts/imx6dl-icore-rqs.dts
> @@ -49,3 +49,14 @@
>  	model = "Engicam i.CoreM6 DualLite/Solo RQS Starter Kit";
>  	compatible = "engicam,imx6-icore-rqs", "fsl,imx6dl";
>  };
> +
> +&i2c3 {
> +	codec: sgtl5000@0a {

Why adding something that the following patch will change right away?

Shawn

> +		compatible = "fsl,sgtl5000";
> +		reg = <0x0a>;
> +		clocks = <&clks IMX6QDL_CLK_CKO>;
> +		VDDA-supply = <&reg_2p5v>;
> +		VDDIO-supply = <&reg_3p3v>;
> +		VDDD-supply = <&reg_1p8v>;
> +	};
> +};
> diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/imx6q-icore-rqs.dts
> index e451b4c..441a28e5 100644
> --- a/arch/arm/boot/dts/imx6q-icore-rqs.dts
> +++ b/arch/arm/boot/dts/imx6q-icore-rqs.dts
> @@ -47,19 +47,6 @@
>  / {
>  	model = "Engicam i.CoreM6 Quad/Dual RQS Starter Kit";
>  	compatible = "engicam,imx6-icore-rqs", "fsl,imx6q";
> -
> -	sound {
> -		compatible = "fsl,imx-audio-sgtl5000";
> -		model = "imx-audio-sgtl5000";
> -		ssi-controller = <&ssi1>;
> -		audio-codec = <&codec>;
> -		audio-routing =
> -			"MIC_IN", "Mic Jack",
> -			"Mic Jack", "Mic Bias",
> -			"Headphone Jack", "HP_OUT";
> -		mux-int-port = <1>;
> -		mux-ext-port = <4>;
> -	};
>  };
>  
>  &i2c3 {
> diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
> index 5fab5be..4032d38 100644
> --- a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
> @@ -118,6 +118,19 @@
>  		clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>;
>  		clock-names = "refclk";
>  	};
> +
> +	sound {
> +		compatible = "fsl,imx-audio-sgtl5000";
> +		model = "imx-audio-sgtl5000";
> +		ssi-controller = <&ssi1>;
> +		audio-codec = <&codec>;
> +		audio-routing =
> +			"MIC_IN", "Mic Jack",
> +			"Mic Jack", "Mic Bias",
> +			"Headphone Jack", "HP_OUT";
> +		mux-int-port = <1>;
> +		mux-ext-port = <4>;
> +	};
>  };
>  
>  &clks {
> -- 
> 1.9.1
> 

Re: [PATCH v2 00/15] ARM: dts: i.MX6: Add lcdif/sound nodes on Engicam SOMs

[Shawn Guo]

On Fri, Mar 24, 2017 at 09:48:35PM +0530, Jagan Teki wrote:
> Jagan Teki (15):
>   ARM: dts: imx6ul-geam: Add backlight support for lcdif
>   ARM: dts: imx6ul-isiot: Add backlight support for lcdif
>   ARM: dts: imx6ul-isiot: Add imx6ul-isiot-common.dtsi
>   ARM: dts: imx6ul-isiot: Add i2c nodes
>   ARM: dts: imx6ul-isiot-common: Add touchscreen node
>   ARM: dts: imx6ul-[geam|isiot]: Add sai2 node

Applied above ones.

Shawn

>   ARM: dts: imx6ul-isiot: Add Sound card with codec node
>   ARM: dts: imx6ul-geam: Add Sound card with codec node
>   ARM: dts: imx6qdl-icore: Add Sound card with codec node
>   ARM: dts: imx6dl-icore-rqs: Add sgtl5000 codec node
>   ARM: dts: imx6qdl-icore-rqs: Replace codec 'lable: node@addr'
>   ARM: dts: imx6dl-icore: Add LVDS support
>   ARM: dts: imx6dl-icore: Add touchscreen node
>   ARM: dts: imx6qdl-icore-rqs: Add CAN nodes
>   ARM: dts: imx6ul-isiot: Add FEC node support