From: Michael Turquette <mturquette@baylibre.com>
To: Kevin Hilman <khilman@baylibre.com>,
"Neil Armstrong" <narmstrong@baylibre.com>
Cc: sboyd@codeaurora.org, carlo@caione.org,
linux-amlogic@lists.infradead.org, linux-clk@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Subject: Re: [PATCH v4 3/3] ARM64: dts: meson-gx: Add MALI nodes for GXBB and GXL
Date: Mon, 27 Mar 2017 12:53:55 -0700 [thread overview]
Message-ID: <149064443540.54062.12740186024138662455@resonance> (raw)
In-Reply-To: <m237e2iirk.fsf@baylibre.com>
Quoting Kevin Hilman (2017-03-24 12:20:31)
> Neil Armstrong <narmstrong@baylibre.com> writes:
>
> > The same MALI-450 MP3 GPU is present in the GXBB and GXL SoCs.
> >
> > The node is simply added in the meson-gxbb.dtsi file.
> >
> > For GXL, since a lot is shared with the GXM that has a MALI-T820 IP, this
> > patch adds a new meson-gxl-mali.dtsi and is included in the SoC specific
> > dtsi files.
> >
> > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
>
> LGTM, I can apply this when the clk driver changes are merged (feel free
> to let me know when that happens, in case I'm not paying attention.)
Applied to clk-meson, a stable branch, which has been merged into
clk-next.
Kevin, the dtsi is all yours.
Regards,
Mike
>
> <bikeshed>
> nit: This series (and previous ones) use MALI, but I believe the correct
> way is Mali. Could you standarize on that throughout the series?
> </bikeshed>
>
> Kevin
>
> > ---
> > arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 37 ++++++++++++++++++++
> > arch/arm64/boot/dts/amlogic/meson-gxl-mali.dtsi | 43 ++++++++++++++++++++++++
> > arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi | 1 +
> > arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi | 1 +
> > 4 files changed, 82 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-mali.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> > index 04b3324..0617a3d 100644
> > --- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> > +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> > @@ -478,6 +478,43 @@
> > };
> > };
> >
> > +&apb {
> > + mali: gpu@c0000 {
> > + compatible = "amlogic,meson-gxbb-mali", "arm,mali-450";
> > + reg = <0x0 0xc0000 0x0 0x40000>;
> > + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-names = "gp", "gpmmu", "pp", "pmu",
> > + "pp0", "ppmmu0", "pp1", "ppmmu1",
> > + "pp2", "ppmmu2";
> > + clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>;
> > + clock-names = "bus", "core";
> > +
> > + /*
> > + * Mali clocking is provided by two identical clock paths
> > + * MALI_0 and MALI_1 muxed to a single clock by a glitch
> > + * free mux to safely change frequency while running.
> > + */
> > + assigned-clocks = <&clkc CLKID_MALI_0_SEL>,
> > + <&clkc CLKID_MALI_0>,
> > + <&clkc CLKID_MALI>; /* Glitch free mux */
> > + assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
> > + <0>, /* Do Nothing */
> > + <&clkc CLKID_MALI_0>;
> > + assigned-clock-rates = <0>, /* Do Nothing */
> > + <666666666>,
> > + <0>; /* Do Nothing */
> > + };
> > +};
> > +
> > &i2c_A {
> > clocks = <&clkc CLKID_I2C>;
> > };
> > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-mali.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-mali.dtsi
> > new file mode 100644
> > index 0000000..f06cc234
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-mali.dtsi
> > @@ -0,0 +1,43 @@
> > +/*
> > + * Copyright (c) 2017 BayLibre SAS
> > + * Author: Neil Armstrong <narmstrong@baylibre.com>
> > + *
> > + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > + */
> > +
> > +&apb {
> > + mali: gpu@c0000 {
> > + compatible = "amlogic,meson-gxbb-mali", "arm,mali-450";
> > + reg = <0x0 0xc0000 0x0 0x40000>;
> > + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-names = "gp", "gpmmu", "pp", "pmu",
> > + "pp0", "ppmmu0", "pp1", "ppmmu1",
> > + "pp2", "ppmmu2";
> > + clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>;
> > + clock-names = "bus", "core";
> > +
> > + /*
> > + * Mali clocking is provided by two identical clock paths
> > + * MALI_0 and MALI_1 muxed to a single clock by a glitch
> > + * free mux to safely change frequency while running.
> > + */
> > + assigned-clocks = <&clkc CLKID_MALI_0_SEL>,
> > + <&clkc CLKID_MALI_0>,
> > + <&clkc CLKID_MALI>; /* Glitch free mux */
> > + assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
> > + <0>, /* Do Nothing */
> > + <&clkc CLKID_MALI_0>;
> > + assigned-clock-rates = <0>, /* Do Nothing */
> > + <666666666>,
> > + <0>; /* Do Nothing */
> > + };
> > +};
> > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi
> > index 615308e..5a90e30 100644
> > --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi
> > +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi
> > @@ -42,6 +42,7 @@
> > */
> >
> > #include "meson-gxl.dtsi"
> > +#include "meson-gxl-mali.dtsi"
> >
> > / {
> > compatible = "amlogic,s905d", "amlogic,meson-gxl";
> > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi
> > index 08237ee..0f78d83 100644
> > --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi
> > +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi
> > @@ -42,6 +42,7 @@
> > */
> >
> > #include "meson-gxl.dtsi"
> > +#include "meson-gxl-mali.dtsi"
> >
> > / {
> > compatible = "amlogic,s905x", "amlogic,meson-gxl";
> --
> To unsubscribe from this list: send the line "unsubscribe linux-clk" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2017-03-27 19:54 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-03-22 10:18 [PATCH v4 0/3] meson-gx: Add mali-450 support Neil Armstrong
2017-03-22 10:18 ` [PATCH v4 1/3] clk: meson-gxbb: Add MALI clock IDS Neil Armstrong
2017-03-22 10:18 ` [PATCH v4 2/3] clk: meson-gxbb: Add MALI clocks Neil Armstrong
2017-04-05 19:43 ` Stephen Boyd
2017-03-22 10:18 ` [PATCH v4 3/3] ARM64: dts: meson-gx: Add MALI nodes for GXBB and GXL Neil Armstrong
2017-03-24 19:20 ` Kevin Hilman
2017-03-27 19:53 ` Michael Turquette [this message]
2017-03-28 14:49 ` Kevin Hilman
2017-03-28 14:51 ` Neil Armstrong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=149064443540.54062.12740186024138662455@resonance \
--to=mturquette@baylibre.com \
--cc=carlo@caione.org \
--cc=devicetree@vger.kernel.org \
--cc=khilman@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=narmstrong@baylibre.com \
--cc=sboyd@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).