[PATCH v6 00/8] Renesas RZ/A1 pin and gpio controller

[PATCH v6 00/8] Renesas RZ/A1 pin and gpio controller

[Jacopo Mondi]

Hello,
   this is 6th round of RZ/A1 pin controller patch series.

Where did we stop: discussion from pin controller driver shifted toward two
new generic pin configuration properties I added to the previous series
(bi-directional and output-enable).

After a really long discussion, we decided to go for handling internally all
bi-directional use cases, making the generic property not a requirement for the
series. Interestingly, we recently found out the number of pins actually
requiring this flag is less (~half) than what reported by the processor manual,
so we could have handled these internally from day one :(

We also now manage internally pins requiring IO direction specified in software
even when configured in alternate function mode (SWIO mode). Most of them are
handled by the driver, some of them have to come from DTS as the user can freely
select if they have to be inputs or outputs. For those pins, and after another
discussion involving NXP developers, we decided to use input-enable and
output-enable properties. I have just sent a patch to add output-enable to the
generic pin configuration properties, but it is currently under discussion.

However, none of the pins currently configured by mainline DTS require those
properties to be specified, so I have dropped in this driver any dependency on
output-enable property, and I'm using instead the already in place
PIN_CONFIG_OUTPUT one. Once output-enable will eventually be accepted, we can
update the driver to make use of it, but since there are no use cases for that
at the moment, it makes not too much sense holding this series back for that.

The total memory occupation we were so worried about of bi-directional and swio
pin tables is now around 100 bytes, because of how the number of pins actually
needing those flags has  reduced and because of how we have arranged the
tables using bitfield structures (credits to Geert here).

Having cleared out dependencies on new pin configuration properties and having
made configuration flags a driver specific issue, I hope this version can be
accepted and land in forthcoming pull request for Renesas PFC updates from
Geert, pending some feedback from the linux-gpio community.

Thanks
   j

v1 -> v2:
- change pin configuration flags as suggested by Chris
- gpio set direction function fixed as suggested by Chris
- add some more example on pin configuration flag usage to dt-binding doc
- fix gpio-controller names to remove unit address as suggested by Geert
- some comments chopped here and there to make the driver less verbose

v2 -> v3:
- fix grammar and syntax in comment and documentation
- fix code style (reverse xmas tree ordering in variable declaration)
- use irqsave/irqrestore in spinlock lock/unlock
- use devm_ version of kasprintf (memory returned was not properly free)
- use bitops.h operation ffs and fls to make sure a single bit is set in pmx
  mask
- Add Geert's reviewed-by to DTS patches

v3 -> v4:
- use "pinmux" property in pmx sub-nodes in place of "renesas,pins"
- use pinconf standard properties to set pin mux additional flags
- add "bi-directional" and "output-enable" to pinconf generic properties
- perform pmx function parsing at dt_node_to_map() time
- change DT bindings to use GENERIC_PINCONF
- change DT bindings to allow sub-nodes to have "pinmux" property specified
- several renames (register names, DT parse functions, set_mux() function)

v4 -> v5:
- use pinctrl_enable() function in pin controller registration function
- update bindings documentation to incorporate Geert's comments
- add generic properties unpack macros

v5 -> v6:
- add tables in driver to manage bi-directional and swio flags
- drop dependecies on new generic pin configuration properties

Jacopo Mondi (8):
  pinctrl: Renesas RZ/A1 pin and gpio controller
  dt-bindings: pinctrl: Add RZ/A1 bindings doc
  arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
  arm: dts: r7s72100: Add pin controller node
  arm: dts: genmai: Add SCIF2 pin group
  arm: dts: genmai: Add RIIC2 pin group
  arm: dts: genmai: Add user led device nodes
  arm: dts: genmai: Add ethernet pin group

 .../bindings/pinctrl/renesas,rza1-pinctrl.txt      |  218 ++++
 arch/arm/boot/dts/r7s72100-genmai.dts              |   69 ++
 arch/arm/boot/dts/r7s72100.dtsi                    |   78 ++
 drivers/pinctrl/Kconfig                            |   11 +
 drivers/pinctrl/Makefile                           |    1 +
 drivers/pinctrl/pinctrl-rza1.c                     | 1309 ++++++++++++++++++++
 include/dt-bindings/pinctrl/r7s72100-pinctrl.h     |   16 +
 7 files changed, 1702 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt
 create mode 100644 drivers/pinctrl/pinctrl-rza1.c
 create mode 100644 include/dt-bindings/pinctrl/r7s72100-pinctrl.h

--
2.7.4

[PATCH v6 1/8] pinctrl: Renesas RZ/A1 pin and gpio controller

[Jacopo Mondi]

Add combined gpio and pin controller driver for Renesas RZ/A1
r7s72100 SoC.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
 drivers/pinctrl/Kconfig        |   11 +
 drivers/pinctrl/Makefile       |    1 +
 drivers/pinctrl/pinctrl-rza1.c | 1309 ++++++++++++++++++++++++++++++++++++++++
 3 files changed, 1321 insertions(+)
 create mode 100644 drivers/pinctrl/pinctrl-rza1.c

diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 37af5e3..d338a33 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -174,6 +174,17 @@ config PINCTRL_ROCKCHIP
 	select GENERIC_IRQ_CHIP
 	select MFD_SYSCON
 
+config PINCTRL_RZA1
+	bool "Renesas RZ/A1 gpio and pinctrl driver"
+	depends on OF
+	depends on ARCH_R7S72100 || COMPILE_TEST
+	select GPIOLIB
+	select GENERIC_PINCTRL_GROUPS
+	select GENERIC_PINMUX_FUNCTIONS
+	select GENERIC_PINCONF
+	help
+	  This selects pinctrl driver for Renesas RZ/A1 platforms.
+
 config PINCTRL_SINGLE
 	tristate "One-register-per-pin type device tree based pinctrl driver"
 	depends on OF
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index 0e9b222..5e52814 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -25,6 +25,7 @@ obj-$(CONFIG_PINCTRL_PALMAS)	+= pinctrl-palmas.o
 obj-$(CONFIG_PINCTRL_PIC32)	+= pinctrl-pic32.o
 obj-$(CONFIG_PINCTRL_PISTACHIO)	+= pinctrl-pistachio.o
 obj-$(CONFIG_PINCTRL_ROCKCHIP)	+= pinctrl-rockchip.o
+obj-$(CONFIG_PINCTRL_RZA1)	+= pinctrl-rza1.o
 obj-$(CONFIG_PINCTRL_SINGLE)	+= pinctrl-single.o
 obj-$(CONFIG_PINCTRL_SIRF)	+= sirf/
 obj-$(CONFIG_PINCTRL_SX150X)	+= pinctrl-sx150x.o
diff --git a/drivers/pinctrl/pinctrl-rza1.c b/drivers/pinctrl/pinctrl-rza1.c
new file mode 100644
index 0000000..a2c535c
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-rza1.c
@@ -0,0 +1,1309 @@
+/*
+ * Combined GPIO and pin controller support for Renesas RZ/A1 (r7s72100) SoC
+ *
+ * Copyright (C) 2017 Jacopo Mondi
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/*
+ * This pin controller/gpio combined driver supports Renesas devices of RZ/A1
+ * family.
+ * This includes SoCs which are sub- or super- sets of this particular line,
+ * as RZ/A1H (r7s721000), RZ/A1M (r7s721010) and RZ/A1L (r7s721020).
+ */
+
+#include <linux/bitops.h>
+#include <linux/err.h>
+#include <linux/gpio/driver.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/slab.h>
+
+#include "core.h"
+#include "devicetree.h"
+#include "pinconf.h"
+#include "pinmux.h"
+
+#define DRIVER_NAME			"pinctrl-rza1"
+
+#define RZA1_P_REG			0x0000
+#define RZA1_PPR_REG			0x0200
+#define RZA1_PM_REG			0x0300
+#define RZA1_PMC_REG			0x0400
+#define RZA1_PFC_REG			0x0500
+#define RZA1_PFCE_REG			0x0600
+#define RZA1_PFCEA_REG			0x0a00
+#define RZA1_PIBC_REG			0x4000
+#define RZA1_PBDC_REG			0x4100
+#define RZA1_PIPC_REG			0x4200
+
+#define RZA1_ADDR(mem, reg, port)	((mem) + (reg) + ((port) * 4))
+
+#define RZA1_NPORTS			12
+#define RZA1_PINS_PER_PORT		16
+#define RZA1_NPINS			(RZA1_PINS_PER_PORT * RZA1_NPORTS)
+#define RZA1_PIN_ID_TO_PORT(id)		((id) / RZA1_PINS_PER_PORT)
+#define RZA1_PIN_ID_TO_PIN(id)		((id) % RZA1_PINS_PER_PORT)
+
+/*
+ * Use 16 lower bits [15:0] for pin identifier
+ * Use 16 higher bits [31:16] for pin mux function
+ */
+#define MUX_PIN_ID_MASK			GENMASK(15, 0)
+#define MUX_FUNC_MASK			GENMASK(31, 16)
+
+#define MUX_FUNC_OFFS			16
+#define MUX_FUNC(pinconf)		\
+	((pinconf & MUX_FUNC_MASK) >> MUX_FUNC_OFFS)
+#define MUX_FUNC_PFC_MASK		BIT(0)
+#define MUX_FUNC_PFCE_MASK		BIT(1)
+#define MUX_FUNC_PFCEA_MASK		BIT(2)
+
+/* Pin mux flags */
+#define MUX_FLAGS_BIDIR			BIT(0)
+#define MUX_FLAGS_SWIO_INPUT		BIT(1)
+#define MUX_FLAGS_SWIO_OUTPUT		BIT(2)
+
+/* ----------------------------------------------------------------------------
+ * RZ/A1 pinmux flags
+ */
+
+/**
+ * rza1_bidir_pin - describe a single pin that needs bidir flag applied.
+ */
+struct rza1_bidir_pin {
+	u8 pin: 4;
+	u8 func: 4;
+};
+
+/**
+ * rza1_bidir_entry - describe a list of pins that needs bidir flag applied.
+ *		      Each struct rza1_bidir_entry describes a port.
+ */
+struct rza1_bidir_entry {
+	const unsigned int npins;
+	const struct rza1_bidir_pin *pins;
+};
+
+/**
+ * rza1_swio_pin - describe a single pin that needs bidir flag applied.
+ */
+struct rza1_swio_pin {
+	u16 pin: 4;
+	u16 port: 4;
+	u16 func: 4;
+	u16 input: 1;
+};
+
+/**
+ * rza1_swio_entry - describe a list of pins that needs swio flag applied
+ */
+struct rza1_swio_entry {
+	const unsigned int npins;
+	const struct rza1_swio_pin *pins;
+};
+
+/**
+ * rza1_pinmux_conf - group together bidir and swio pinmux flag tables
+ */
+struct rza1_pinmux_conf {
+	const struct rza1_bidir_entry *bidir_entries;
+	const struct rza1_swio_entry *swio_entries;
+};
+
+/* ----------------------------------------------------------------------------
+ * RZ/A1H (r7s72100) pinmux flags
+ */
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p1[] = {
+	{ .pin = 0, .func = 1 },
+	{ .pin = 1, .func = 1 },
+	{ .pin = 2, .func = 1 },
+	{ .pin = 3, .func = 1 },
+	{ .pin = 4, .func = 1 },
+	{ .pin = 5, .func = 1 },
+	{ .pin = 6, .func = 1 },
+	{ .pin = 7, .func = 1 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p2[] = {
+	{ .pin = 0, .func = 1 },
+	{ .pin = 1, .func = 1 },
+	{ .pin = 2, .func = 1 },
+	{ .pin = 3, .func = 1 },
+	{ .pin = 4, .func = 1 },
+	{ .pin = 0, .func = 4 },
+	{ .pin = 1, .func = 4 },
+	{ .pin = 2, .func = 4 },
+	{ .pin = 3, .func = 4 },
+	{ .pin = 5, .func = 1 },
+	{ .pin = 6, .func = 1 },
+	{ .pin = 7, .func = 1 },
+	{ .pin = 8, .func = 1 },
+	{ .pin = 9, .func = 1 },
+	{ .pin = 10, .func = 1 },
+	{ .pin = 11, .func = 1 },
+	{ .pin = 12, .func = 1 },
+	{ .pin = 13, .func = 1 },
+	{ .pin = 14, .func = 1 },
+	{ .pin = 15, .func = 1 },
+	{ .pin = 12, .func = 4 },
+	{ .pin = 13, .func = 4 },
+	{ .pin = 14, .func = 4 },
+	{ .pin = 15, .func = 4 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p3[] = {
+	{ .pin = 3, .func = 2 },
+	{ .pin = 10, .func = 7 },
+	{ .pin = 11, .func = 7 },
+	{ .pin = 13, .func = 7 },
+	{ .pin = 14, .func = 7 },
+	{ .pin = 15, .func = 7 },
+	{ .pin = 10, .func = 8 },
+	{ .pin = 11, .func = 8 },
+	{ .pin = 13, .func = 8 },
+	{ .pin = 14, .func = 8 },
+	{ .pin = 15, .func = 8 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p4[] = {
+	{ .pin = 0, .func = 8 },
+	{ .pin = 1, .func = 8 },
+	{ .pin = 2, .func = 8 },
+	{ .pin = 3, .func = 8 },
+	{ .pin = 10, .func = 3 },
+	{ .pin = 11, .func = 3 },
+	{ .pin = 13, .func = 3 },
+	{ .pin = 14, .func = 3 },
+	{ .pin = 15, .func = 3 },
+	{ .pin = 10, .func = 4 },
+	{ .pin = 11, .func = 4 },
+	{ .pin = 13, .func = 4 },
+	{ .pin = 14, .func = 4 },
+	{ .pin = 15, .func = 4 },
+	{ .pin = 12, .func = 5 },
+	{ .pin = 13, .func = 5 },
+	{ .pin = 14, .func = 5 },
+	{ .pin = 15, .func = 5 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p6[] = {
+	{ .pin = 0, .func = 1 },
+	{ .pin = 1, .func = 1 },
+	{ .pin = 2, .func = 1 },
+	{ .pin = 3, .func = 1 },
+	{ .pin = 4, .func = 1 },
+	{ .pin = 5, .func = 1 },
+	{ .pin = 6, .func = 1 },
+	{ .pin = 7, .func = 1 },
+	{ .pin = 8, .func = 1 },
+	{ .pin = 9, .func = 1 },
+	{ .pin = 10, .func = 1 },
+	{ .pin = 11, .func = 1 },
+	{ .pin = 12, .func = 1 },
+	{ .pin = 13, .func = 1 },
+	{ .pin = 14, .func = 1 },
+	{ .pin = 15, .func = 1 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p7[] = {
+	{ .pin = 13, .func = 3 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p8[] = {
+	{ .pin = 8, .func = 3 },
+	{ .pin = 9, .func = 3 },
+	{ .pin = 10, .func = 3 },
+	{ .pin = 11, .func = 3 },
+	{ .pin = 14, .func = 2 },
+	{ .pin = 15, .func = 2 },
+	{ .pin = 14, .func = 3 },
+	{ .pin = 15, .func = 3 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p9[] = {
+	{ .pin = 0, .func = 2 },
+	{ .pin = 1, .func = 2 },
+	{ .pin = 4, .func = 2 },
+	{ .pin = 5, .func = 2 },
+	{ .pin = 6, .func = 2 },
+	{ .pin = 7, .func = 2 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p11[] = {
+	{ .pin = 6, .func = 2 },
+	{ .pin = 7, .func = 2 },
+	{ .pin = 9, .func = 2 },
+	{ .pin = 6, .func = 4 },
+	{ .pin = 7, .func = 4 },
+	{ .pin = 9, .func = 4 },
+	{ .pin = 10, .func = 2 },
+	{ .pin = 11, .func = 2 },
+	{ .pin = 10, .func = 4 },
+	{ .pin = 11, .func = 4 },
+	{ .pin = 12, .func = 4 },
+	{ .pin = 13, .func = 4 },
+	{ .pin = 14, .func = 4 },
+	{ .pin = 15, .func = 4 },
+};
+
+static const struct rza1_swio_pin rza1h_swio_pins[] = {
+	{ .port = 2, .pin = 7, .func = 4, .input = 0 },
+	{ .port = 2, .pin = 11, .func = 4, .input = 0 },
+	{ .port = 3, .pin = 7, .func = 3, .input = 0 },
+	{ .port = 3, .pin = 7, .func = 8, .input = 0 },
+	{ .port = 4, .pin = 7, .func = 5, .input = 0 },
+	{ .port = 4, .pin = 7, .func = 11, .input = 0 },
+	{ .port = 4, .pin = 15, .func = 6, .input = 0 },
+	{ .port = 5, .pin = 0, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 1, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 2, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 3, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 4, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 5, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 6, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 7, .func = 1, .input = 1 },
+	{ .port = 7, .pin = 4, .func = 6, .input = 0 },
+	{ .port = 7, .pin = 11, .func = 2, .input = 0 },
+	{ .port = 8, .pin = 10, .func = 8, .input = 0 },
+	{ .port = 10, .pin = 15, .func = 2, .input = 0 },
+};
+
+static const struct rza1_bidir_entry rza1h_bidir_entries[RZA1_NPORTS] = {
+	[1] = { ARRAY_SIZE(rza1h_bidir_pins_p1), rza1h_bidir_pins_p1 },
+	[2] = { ARRAY_SIZE(rza1h_bidir_pins_p2), rza1h_bidir_pins_p2 },
+	[3] = { ARRAY_SIZE(rza1h_bidir_pins_p3), rza1h_bidir_pins_p3 },
+	[4] = { ARRAY_SIZE(rza1h_bidir_pins_p4), rza1h_bidir_pins_p4 },
+	[6] = { ARRAY_SIZE(rza1h_bidir_pins_p6), rza1h_bidir_pins_p6 },
+	[7] = { ARRAY_SIZE(rza1h_bidir_pins_p7), rza1h_bidir_pins_p7 },
+	[8] = { ARRAY_SIZE(rza1h_bidir_pins_p8), rza1h_bidir_pins_p8 },
+	[9] = { ARRAY_SIZE(rza1h_bidir_pins_p9), rza1h_bidir_pins_p9 },
+	[11] = { ARRAY_SIZE(rza1h_bidir_pins_p11), rza1h_bidir_pins_p11 },
+};
+
+static const struct rza1_swio_entry rza1h_swio_entries[] = {
+	[0] = { ARRAY_SIZE(rza1h_swio_pins), rza1h_swio_pins },
+};
+
+/* RZ/A1H (r7s72100x) pinmux flags table */
+static const struct rza1_pinmux_conf rza1h_pmx_conf = {
+	.bidir_entries	= rza1h_bidir_entries,
+	.swio_entries	= rza1h_swio_entries,
+};
+
+/* ----------------------------------------------------------------------------
+ * RZ/A1 types
+ */
+/**
+ * rza1_mux_conf - describes a pin multiplexing operation
+ *
+ * @id: the pin identifier from 0 to RZA1_NPINS
+ * @port: the port where pin sits on
+ * @pin: pin id
+ * @mux_func: alternate function id number
+ * @mux_flags: alternate function flags
+ * @value: output value to set the pin to
+ */
+struct rza1_mux_conf {
+	u16 id;
+	u8 port;
+	u8 pin;
+	u8 mux_func;
+	u8 mux_flags;
+	u8 value;
+};
+
+/**
+ * rza1_port - describes a pin port
+ *
+ * This is mostly useful to lock register writes per-bank and not globally.
+ *
+ * @lock: protect access to HW registers
+ * @id: port number
+ * @base: logical address base
+ * @pins: pins sitting on this port
+ */
+struct rza1_port {
+	spinlock_t lock;
+	unsigned int id;
+	void __iomem *base;
+	struct pinctrl_pin_desc *pins;
+};
+
+/**
+ * rza1_pinctrl - RZ pincontroller device
+ *
+ * @dev: parent device structure
+ * @mutex: protect [pinctrl|pinmux]_generic functions
+ * @base: logical address base
+ * @nports: number of pin controller ports
+ * @ports: pin controller banks
+ * @pins: pin array for pinctrl core
+ * @desc: pincontroller desc for pinctrl core
+ * @pctl: pinctrl device
+ * @data: device specific data
+ */
+struct rza1_pinctrl {
+	struct device *dev;
+
+	struct mutex mutex;
+
+	void __iomem *base;
+
+	unsigned int nport;
+	struct rza1_port *ports;
+
+	struct pinctrl_pin_desc *pins;
+	struct pinctrl_desc desc;
+	struct pinctrl_dev *pctl;
+
+	const void *data;
+};
+
+/* ----------------------------------------------------------------------------
+ * RZ/A1 pinmux flags
+ */
+static inline bool rza1_pinmux_get_bidir(unsigned int port,
+					 unsigned int pin,
+					 unsigned int func,
+					 const struct rza1_bidir_entry *table)
+{
+	const struct rza1_bidir_entry *entry = &table[port];
+	const struct rza1_bidir_pin *bidir_pin;
+	unsigned int i;
+
+	for (i = 0; i < entry->npins; ++i) {
+		bidir_pin = &entry->pins[i];
+		if (bidir_pin->pin == pin && bidir_pin->func == func)
+			return true;
+	}
+
+	return false;
+}
+
+static inline int rza1_pinmux_get_swio(unsigned int port,
+				       unsigned int pin,
+				       unsigned int func,
+				       const struct rza1_swio_entry *table)
+{
+	const struct rza1_swio_pin *swio_pin;
+	unsigned int i;
+
+
+	for (i = 0; i < table->npins; ++i) {
+		swio_pin = &table->pins[i];
+		if (swio_pin->port == port && swio_pin->pin == pin &&
+		    swio_pin->func == func)
+			return swio_pin->input;
+	}
+
+	return -ENOENT;
+}
+
+/**
+ * rza1_pinmux_get_flags() - return pinmux flags associated to a pin
+ */
+static unsigned int rza1_pinmux_get_flags(unsigned int port, unsigned int pin,
+					  unsigned int func,
+					  struct rza1_pinctrl *rza1_pctl)
+
+{
+	const struct rza1_pinmux_conf *pmx_conf = rza1_pctl->data;
+	const struct rza1_bidir_entry *bidir_entries = pmx_conf->bidir_entries;
+	const struct rza1_swio_entry *swio_entries = pmx_conf->swio_entries;
+	unsigned int pmx_flags = 0;
+	int ret;
+
+	if (rza1_pinmux_get_bidir(port, pin, func, bidir_entries))
+		pmx_flags |= MUX_FLAGS_BIDIR;
+
+	ret = rza1_pinmux_get_swio(port, pin, func, swio_entries);
+	if (ret == 0)
+		pmx_flags |= MUX_FLAGS_SWIO_OUTPUT;
+	else if (ret > 0)
+		pmx_flags |= MUX_FLAGS_SWIO_INPUT;
+
+	return pmx_flags;
+}
+
+/* ----------------------------------------------------------------------------
+ * RZ/A1 SoC operations
+ */
+
+/**
+ * rza1_set_bit() - un-locked set/clear a single bit in pin configuration
+ *		    registers
+ */
+static inline void rza1_set_bit(struct rza1_port *port, unsigned int reg,
+				unsigned int bit, bool set)
+{
+	void __iomem *mem = RZA1_ADDR(port->base, reg, port->id);
+	u16 val = ioread16(mem);
+
+	if (set)
+		val |= BIT(bit);
+	else
+		val &= ~BIT(bit);
+
+	iowrite16(val, mem);
+}
+
+static inline unsigned int rza1_get_bit(struct rza1_port *port,
+					unsigned int reg, unsigned int bit)
+{
+	void __iomem *mem = RZA1_ADDR(port->base, reg, port->id);
+
+	return ioread16(mem) & BIT(bit);
+}
+
+/**
+ * rza1_pin_reset() - reset a pin to default initial state
+ *
+ * Reset pin state disabling input buffer and bi-directional control,
+ * and configure it as input port.
+ * Note that pin is now configured with direction as input but with input
+ * buffer disabled. This implies the pin value cannot be read in this state.
+ *
+ * @port: port where pin sits on
+ * @pin: pin offset
+ */
+static void rza1_pin_reset(struct rza1_port *port, unsigned int pin)
+{
+	unsigned long irqflags;
+
+	spin_lock_irqsave(&port->lock, irqflags);
+	rza1_set_bit(port, RZA1_PIBC_REG, pin, 0);
+	rza1_set_bit(port, RZA1_PBDC_REG, pin, 0);
+
+	rza1_set_bit(port, RZA1_PM_REG, pin, 1);
+	rza1_set_bit(port, RZA1_PMC_REG, pin, 0);
+	rza1_set_bit(port, RZA1_PIPC_REG, pin, 0);
+	spin_unlock_irqrestore(&port->lock, irqflags);
+}
+
+static inline int rza1_pin_get_direction(struct rza1_port *port,
+					 unsigned int pin)
+{
+	unsigned long irqflags;
+	int input;
+
+	spin_lock_irqsave(&port->lock, irqflags);
+	input = rza1_get_bit(port, RZA1_PM_REG, pin);
+	spin_unlock_irqrestore(&port->lock, irqflags);
+
+	return !!input;
+}
+
+/**
+ * rza1_pin_set_direction() - set I/O direction on a pin in port mode
+ *
+ * When running in output port mode keep PBDC enabled to allow reading the
+ * pin value from PPR.
+ *
+ * @port: port where pin sits on
+ * @pin: pin offset
+ * @input: input enable/disable flag
+ */
+static inline void rza1_pin_set_direction(struct rza1_port *port,
+					  unsigned int pin, bool input)
+{
+	unsigned long irqflags;
+
+	spin_lock_irqsave(&port->lock, irqflags);
+
+	rza1_set_bit(port, RZA1_PIBC_REG, pin, 1);
+	if (input) {
+		rza1_set_bit(port, RZA1_PM_REG, pin, 1);
+		rza1_set_bit(port, RZA1_PBDC_REG, pin, 0);
+	} else {
+		rza1_set_bit(port, RZA1_PM_REG, pin, 0);
+		rza1_set_bit(port, RZA1_PBDC_REG, pin, 1);
+	}
+
+	spin_unlock_irqrestore(&port->lock, irqflags);
+}
+
+static inline void rza1_pin_set(struct rza1_port *port, unsigned int pin,
+				unsigned int value)
+{
+	unsigned long irqflags;
+
+	spin_lock_irqsave(&port->lock, irqflags);
+	rza1_set_bit(port, RZA1_P_REG, pin, !!value);
+	spin_unlock_irqrestore(&port->lock, irqflags);
+}
+
+static inline int rza1_pin_get(struct rza1_port *port, unsigned int pin)
+{
+	unsigned long irqflags;
+	int val;
+
+	spin_lock_irqsave(&port->lock, irqflags);
+	val = rza1_get_bit(port, RZA1_PPR_REG, pin);
+	spin_unlock_irqrestore(&port->lock, irqflags);
+
+	return val;
+}
+
+/**
+ * rza1_pin_mux_single() - configure pin multiplexing on a single pin
+ *
+ * @pinctrl: RZ/A1 pin controller device
+ * @mux_conf: pin multiplexing descriptor
+ */
+static int rza1_pin_mux_single(struct rza1_pinctrl *rza1_pctl,
+			       struct rza1_mux_conf *mux_conf)
+{
+	struct rza1_port *port = &rza1_pctl->ports[mux_conf->port];
+	unsigned int pin = mux_conf->pin;
+	u8 mux_func = mux_conf->mux_func;
+	u8 mux_flags = mux_conf->mux_flags;
+	u8 mux_flags_from_table;
+
+	rza1_pin_reset(port, pin);
+
+	/* SWIO pinmux flags coming from DT are high precedence */
+	mux_flags_from_table = rza1_pinmux_get_flags(port->id, pin, mux_func,
+						     rza1_pctl);
+	if (mux_flags)
+		mux_flags |= (mux_flags_from_table & MUX_FLAGS_BIDIR);
+	else
+		mux_flags = mux_flags_from_table;
+
+	if (mux_flags & MUX_FLAGS_BIDIR)
+		rza1_set_bit(port, RZA1_PBDC_REG, pin, 1);
+
+	/*
+	 * Enable alternate function mode and select it.
+	 *
+	 * Be careful here: the pin mux sub-nodes in device tree
+	 * enumerate alternate functions from 1 to 8;
+	 * subtract 1 before using macros to match registers configuration
+	 * which expects numbers from 0 to 7 instead.
+	 *
+	 * ----------------------------------------------------
+	 * Alternate mode selection table:
+	 *
+	 * PMC	PFC	PFCE	PFCAE	(mux_func - 1)
+	 * 1	0	0	0	0
+	 * 1	1	0	0	1
+	 * 1	0	1	0	2
+	 * 1	1	1	0	3
+	 * 1	0	0	1	4
+	 * 1	1	0	1	5
+	 * 1	0	1	1	6
+	 * 1	1	1	1	7
+	 * ----------------------------------------------------
+	 */
+	mux_func -= 1;
+	rza1_set_bit(port, RZA1_PFC_REG, pin, mux_func & MUX_FUNC_PFC_MASK);
+	rza1_set_bit(port, RZA1_PFCE_REG, pin, mux_func & MUX_FUNC_PFCE_MASK);
+	rza1_set_bit(port, RZA1_PFCEA_REG, pin, mux_func & MUX_FUNC_PFCEA_MASK);
+
+	/*
+	 * All alternate functions except a few need PIPCn = 1.
+	 * If PIPCn has to stay disabled (SW IO mode), configure PMn according
+	 * to I/O direction specified by pin configuration -after- PMC has been
+	 * set to one.
+	 */
+	if (!(mux_flags & (MUX_FLAGS_SWIO_INPUT | MUX_FLAGS_SWIO_OUTPUT)))
+		rza1_set_bit(port, RZA1_PIPC_REG, pin, 1);
+
+	rza1_set_bit(port, RZA1_PMC_REG, pin, 1);
+	rza1_set_bit(port, RZA1_PM_REG, pin, mux_flags & MUX_FLAGS_SWIO_INPUT);
+
+	return 0;
+}
+
+/* ----------------------------------------------------------------------------
+ * gpio operations
+ */
+
+/**
+ * rza1_gpio_request() - configure pin in port mode
+ *
+ * Configure a pin as gpio (port mode).
+ * After reset, the pin is in input mode with input buffer disabled.
+ * To use the pin as input or output, set_direction shall be called first
+ *
+ * @chip: gpio chip where the gpio sits on
+ * @gpio: gpio offset
+ */
+static int rza1_gpio_request(struct gpio_chip *chip, unsigned int gpio)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	rza1_pin_reset(port, gpio);
+
+	return 0;
+}
+
+/**
+ * rza1_gpio_disable_free() - reset a pin
+ *
+ * Surprisingly, disable_free a gpio, is equivalent to request it.
+ * Reset pin to port mode, with input buffer disabled. This overwrites all
+ * port direction settings applied with set_direction
+ *
+ * @chip: gpio chip where the gpio sits on
+ * @gpio: gpio offset
+ */
+static void rza1_gpio_free(struct gpio_chip *chip, unsigned int gpio)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	rza1_pin_reset(port, gpio);
+}
+
+static int rza1_gpio_get_direction(struct gpio_chip *chip, unsigned int gpio)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	return rza1_pin_get_direction(port, gpio);
+}
+
+static int rza1_gpio_direction_input(struct gpio_chip *chip,
+				     unsigned int gpio)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	rza1_pin_set_direction(port, gpio, true);
+
+	return 0;
+}
+
+static int rza1_gpio_direction_output(struct gpio_chip *chip,
+				      unsigned int gpio,
+				      int value)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	/* Set value before driving pin direction */
+	rza1_pin_set(port, gpio, value);
+	rza1_pin_set_direction(port, gpio, false);
+
+	return 0;
+}
+
+/**
+ * rza1_gpio_get() - read a gpio pin value
+ *
+ * Read gpio pin value through PPR register.
+ * Requires bi-directional mode to work when reading the value of a pin
+ * in output mode
+ *
+ * @chip: gpio chip where the gpio sits on
+ * @gpio: gpio offset
+ */
+static int rza1_gpio_get(struct gpio_chip *chip, unsigned int gpio)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	return rza1_pin_get(port, gpio);
+}
+
+static void rza1_gpio_set(struct gpio_chip *chip, unsigned int gpio,
+			  int value)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	rza1_pin_set(port, gpio, value);
+}
+
+struct gpio_chip rza1_gpiochip_template = {
+	.request		= rza1_gpio_request,
+	.free			= rza1_gpio_free,
+	.get_direction		= rza1_gpio_get_direction,
+	.direction_input	= rza1_gpio_direction_input,
+	.direction_output	= rza1_gpio_direction_output,
+	.get			= rza1_gpio_get,
+	.set			= rza1_gpio_set,
+};
+/* ----------------------------------------------------------------------------
+ * pinctrl operations
+ */
+
+/**
+ * rza1_dt_node_pin_count() - Count number of pins in a dt node or in all its
+ *			      children sub-nodes
+ *
+ * @np: device tree node to parse
+ */
+static int rza1_dt_node_pin_count(struct device_node *np)
+{
+	struct device_node *child;
+	struct property *of_pins;
+	unsigned int npins;
+
+	of_pins = of_find_property(np, "pinmux", NULL);
+	if (of_pins)
+		return of_pins->length / sizeof(u32);
+
+	npins = 0;
+	for_each_child_of_node(np, child) {
+		of_pins = of_find_property(child, "pinmux", NULL);
+		if (!of_pins)
+			return -EINVAL;
+
+		npins += of_pins->length / sizeof(u32);
+	}
+
+	return npins;
+}
+
+/**
+ * rza1_parse_pmx_function() - parse a pin mux sub-node
+ *
+ * @rza1_pctl: RZ/A1 pin controller device
+ * @np: of pmx sub-node
+ * @mux_confs: array of pin mux configurations to fill with parsed info
+ * @grpins: array of pin ids to mux
+ */
+static int rza1_parse_pinmux_node(struct rza1_pinctrl *rza1_pctl,
+				  struct device_node *np,
+				  struct rza1_mux_conf *mux_confs,
+				  unsigned int *grpins)
+{
+	struct pinctrl_dev *pctldev = rza1_pctl->pctl;
+	char const *prop_name = "pinmux";
+	unsigned long *pin_configs;
+	unsigned int npin_configs;
+	struct property *of_pins;
+	unsigned int npins;
+	u8 pinmux_flags;
+	unsigned int i;
+	int ret;
+
+	of_pins = of_find_property(np, prop_name, NULL);
+	if (!of_pins) {
+		dev_dbg(rza1_pctl->dev, "Missing %s property\n", prop_name);
+		return -ENOENT;
+	}
+	npins = of_pins->length / sizeof(u32);
+
+	/*
+	 * Collect pin configuration properties: they apply to all pins in
+	 * this sub-node
+	 */
+	ret = pinconf_generic_parse_dt_config(np, pctldev, &pin_configs,
+					      &npin_configs);
+	if (ret) {
+		dev_err(rza1_pctl->dev,
+			"Unable to parse pin configuration options for %s\n",
+			np->name);
+		return ret;
+	}
+
+	/*
+	 * Create a mask with pinmux flags from pin configuration;
+	 * very few pins (TIOC[0-4][A|B|C|D] require SWIO direction
+	 * specified in device tree.
+	 */
+	pinmux_flags = 0;
+	for (i = 0; i < npin_configs && pinmux_flags == 0; i++)
+		switch (pinconf_to_config_param(pin_configs[i])) {
+		case PIN_CONFIG_INPUT_ENABLE:
+			pinmux_flags |= MUX_FLAGS_SWIO_INPUT;
+			break;
+		case PIN_CONFIG_OUTPUT:
+			pinmux_flags |= MUX_FLAGS_SWIO_OUTPUT;
+		default:
+			break;
+
+		}
+
+	kfree(pin_configs);
+
+	/* Collect pin positions and their mux settings. */
+	for (i = 0; i < npins; ++i) {
+		u32 of_pinconf;
+		struct rza1_mux_conf *mux_conf = &mux_confs[i];
+
+		ret = of_property_read_u32_index(np, prop_name, i, &of_pinconf);
+		if (ret)
+			return ret;
+
+		mux_conf->id		= of_pinconf & MUX_PIN_ID_MASK;
+		mux_conf->port		= RZA1_PIN_ID_TO_PORT(mux_conf->id);
+		mux_conf->pin		= RZA1_PIN_ID_TO_PIN(mux_conf->id);
+		mux_conf->mux_func	= MUX_FUNC(of_pinconf);
+		mux_conf->mux_flags	= pinmux_flags;
+
+		if (mux_conf->port >= RZA1_NPORTS ||
+		    mux_conf->pin >= RZA1_PINS_PER_PORT) {
+			dev_err(rza1_pctl->dev,
+				"Wrong port %u pin %u for %s property\n",
+				mux_conf->port, mux_conf->pin, prop_name);
+			return -EINVAL;
+		}
+
+		grpins[i] = mux_conf->id;
+	}
+
+	return npins;
+}
+
+/**
+ * rza1_dt_node_to_map() - map a pin mux node to a function/group
+ *
+ * Parse and register a pin mux function.
+ *
+ * @pctldev: pin controller device
+ * @np: device tree node to parse
+ * @map: pointer to pin map (output)
+ * @num_maps: number of collected maps (output)
+ */
+static int rza1_dt_node_to_map(struct pinctrl_dev *pctldev,
+			       struct device_node *np,
+			       struct pinctrl_map **map,
+			       unsigned int *num_maps)
+{
+	struct rza1_pinctrl *rza1_pctl = pinctrl_dev_get_drvdata(pctldev);
+	struct rza1_mux_conf *mux_confs, *mux_conf;
+	unsigned int *grpins, *grpin;
+	struct device_node *child;
+	const char *grpname;
+	const char **fngrps;
+	int ret, npins;
+
+	npins = rza1_dt_node_pin_count(np);
+	if (npins < 0) {
+		dev_err(rza1_pctl->dev, "invalid pinmux node structure\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * Functions are made of 1 group only;
+	 * in fact, functions and groups are identical for this pin controller
+	 * except that functions carry an array of per-pin mux configuration
+	 * settings.
+	 */
+	mux_confs = devm_kcalloc(rza1_pctl->dev, npins, sizeof(*mux_confs),
+				 GFP_KERNEL);
+	grpins = devm_kcalloc(rza1_pctl->dev, npins, sizeof(*grpins),
+			      GFP_KERNEL);
+	fngrps = devm_kzalloc(rza1_pctl->dev, sizeof(*fngrps), GFP_KERNEL);
+
+	if (!mux_confs || !grpins || !fngrps)
+		return -ENOMEM;
+
+	/*
+	 * Parse the pinmux node.
+	 * If the node does not contain "pinmux" property (-ENOENT)
+	 * that property shall be specified in all its children sub-nodes.
+	 */
+	mux_conf = &mux_confs[0];
+	grpin = &grpins[0];
+
+	ret = rza1_parse_pinmux_node(rza1_pctl, np, mux_conf, grpin);
+	if (ret == -ENOENT)
+		for_each_child_of_node(np, child) {
+			ret = rza1_parse_pinmux_node(rza1_pctl, child, mux_conf,
+						     grpin);
+			if (ret < 0)
+				return ret;
+
+			grpin += ret;
+			mux_conf += ret;
+		}
+	else if (ret < 0)
+		return ret;
+
+	/* Register pin group and function name to pinctrl_generic */
+	grpname	= np->name;
+	fngrps[0] = grpname;
+
+	mutex_lock(&rza1_pctl->mutex);
+	ret = pinctrl_generic_add_group(pctldev, grpname, grpins, npins,
+					NULL);
+	if (ret) {
+		mutex_unlock(&rza1_pctl->mutex);
+		return ret;
+	}
+
+	ret = pinmux_generic_add_function(pctldev, grpname, fngrps, 1,
+					  mux_confs);
+	if (ret)
+		goto remove_group;
+	mutex_unlock(&rza1_pctl->mutex);
+
+	dev_info(rza1_pctl->dev, "Parsed function and group %s with %d pins\n",
+				 grpname, npins);
+
+	/* Create map where to retrieve function and mux settings from */
+	*num_maps = 0;
+	*map = kzalloc(sizeof(**map), GFP_KERNEL);
+	if (!*map) {
+		ret = -ENOMEM;
+		goto remove_function;
+	}
+
+	(*map)->type = PIN_MAP_TYPE_MUX_GROUP;
+	(*map)->data.mux.group = np->name;
+	(*map)->data.mux.function = np->name;
+	*num_maps = 1;
+
+	return 0;
+
+remove_function:
+	mutex_lock(&rza1_pctl->mutex);
+	pinmux_generic_remove_last_function(pctldev);
+
+remove_group:
+	pinctrl_generic_remove_last_group(pctldev);
+	mutex_unlock(&rza1_pctl->mutex);
+
+	dev_info(rza1_pctl->dev, "Unable to parse function and group %s\n",
+				 grpname);
+
+	return ret;
+}
+
+static void rza1_dt_free_map(struct pinctrl_dev *pctldev,
+			     struct pinctrl_map *map, unsigned int num_maps)
+{
+	kfree(map);
+}
+
+static const struct pinctrl_ops rza1_pinctrl_ops = {
+	.get_groups_count	= pinctrl_generic_get_group_count,
+	.get_group_name		= pinctrl_generic_get_group_name,
+	.get_group_pins		= pinctrl_generic_get_group_pins,
+	.dt_node_to_map		= rza1_dt_node_to_map,
+	.dt_free_map		= rza1_dt_free_map,
+};
+
+/* ----------------------------------------------------------------------------
+ * pinmux operations
+ */
+
+/**
+ * rza1_set_mux() - retrieve pins from a group and apply their mux settings
+ *
+ * @pctldev: pin controller device
+ * @selector: function selector
+ * @group: group selector
+ */
+static int rza1_set_mux(struct pinctrl_dev *pctldev, unsigned int selector,
+			   unsigned int group)
+{
+	struct rza1_pinctrl *rza1_pctl = pinctrl_dev_get_drvdata(pctldev);
+	struct rza1_mux_conf *mux_confs;
+	struct function_desc *func;
+	struct group_desc *grp;
+	int i;
+
+	grp = pinctrl_generic_get_group(pctldev, group);
+	if (!grp)
+		return -EINVAL;
+
+	func = pinmux_generic_get_function(pctldev, selector);
+	if (!func)
+		return -EINVAL;
+
+	mux_confs = (struct rza1_mux_conf *)func->data;
+	for (i = 0; i < grp->num_pins; ++i) {
+		int ret;
+
+		ret = rza1_pin_mux_single(rza1_pctl, &mux_confs[i]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+struct pinmux_ops rza1_pinmux_ops = {
+	.get_functions_count	= pinmux_generic_get_function_count,
+	.get_function_name	= pinmux_generic_get_function_name,
+	.get_function_groups	= pinmux_generic_get_function_groups,
+	.set_mux		= rza1_set_mux,
+	.strict			= true,
+};
+
+/* ----------------------------------------------------------------------------
+ * RZ/A1 pin controller driver operations
+ */
+
+static unsigned int rza1_count_gpio_chips(struct device_node *np)
+{
+	struct device_node *child;
+	unsigned int count = 0;
+
+	for_each_child_of_node(np, child) {
+		if (!of_property_read_bool(child, "gpio-controller"))
+			continue;
+
+		count++;
+	}
+
+	return count;
+}
+
+/**
+ * rza1_parse_gpiochip() - parse and register a gpio chip and pin range
+ *
+ * The gpio controller subnode shall provide a "gpio-ranges" list property as
+ * defined by gpio device tree binding documentation.
+ *
+ * @rza1_pctl: RZ/A1 pin controller device
+ * @np: of gpio-controller node
+ * @chip: gpio chip to register to gpiolib
+ * @range: pin range to register to pinctrl core
+ */
+static int rza1_parse_gpiochip(struct rza1_pinctrl *rza1_pctl,
+			       struct device_node *np,
+			       struct gpio_chip *chip,
+			       struct pinctrl_gpio_range *range)
+{
+	const char *list_name = "gpio-ranges";
+	struct of_phandle_args of_args;
+	unsigned int gpioport;
+	u32 pinctrl_base;
+	int ret;
+
+	ret = of_parse_phandle_with_fixed_args(np, list_name, 3, 0, &of_args);
+	if (ret) {
+		dev_err(rza1_pctl->dev, "Unable to parse %s list property\n",
+			list_name);
+		return ret;
+	}
+
+	/*
+	 * Find out on which port this gpio-chip maps to by inspecting the
+	 * second argument of the "gpio-ranges" property.
+	 */
+	pinctrl_base = of_args.args[1];
+	gpioport = RZA1_PIN_ID_TO_PORT(pinctrl_base);
+	if (gpioport > RZA1_NPORTS) {
+		dev_err(rza1_pctl->dev,
+			"Invalid values in property %s\n", list_name);
+		return -EINVAL;
+	}
+
+	*chip		= rza1_gpiochip_template;
+	chip->base	= -1;
+	chip->label	= devm_kasprintf(rza1_pctl->dev, GFP_KERNEL, "%s-%u",
+					 np->name, gpioport);
+	chip->ngpio	= of_args.args[2];
+	chip->of_node	= np;
+	chip->parent	= rza1_pctl->dev;
+
+	range->id	= gpioport;
+	range->name	= chip->label;
+	range->pin_base	= range->base = pinctrl_base;
+	range->npins	= of_args.args[2];
+	range->gc	= chip;
+
+	ret = devm_gpiochip_add_data(rza1_pctl->dev, chip,
+				     &rza1_pctl->ports[gpioport]);
+	if (ret)
+		return ret;
+
+	pinctrl_add_gpio_range(rza1_pctl->pctl, range);
+
+	dev_info(rza1_pctl->dev, "Parsed gpiochip %s with %d pins\n",
+		 chip->label, chip->ngpio);
+
+	return 0;
+}
+
+/**
+ * rza1_gpio_register() - parse DT to collect gpio-chips and gpio-ranges
+ *
+ * @rza1_pctl: RZ/A1 pin controller device
+ */
+static int rza1_gpio_register(struct rza1_pinctrl *rza1_pctl)
+{
+	struct device_node *np = rza1_pctl->dev->of_node;
+	struct pinctrl_gpio_range *gpio_ranges;
+	struct gpio_chip *gpio_chips;
+	struct device_node *child;
+	unsigned int ngpiochips;
+	unsigned int i;
+	int ret;
+
+	ngpiochips = rza1_count_gpio_chips(np);
+	if (ngpiochips == 0) {
+		dev_dbg(rza1_pctl->dev, "No gpiochip registered\n");
+		return 0;
+	}
+
+	gpio_chips = devm_kcalloc(rza1_pctl->dev, ngpiochips,
+				  sizeof(*gpio_chips), GFP_KERNEL);
+	gpio_ranges = devm_kcalloc(rza1_pctl->dev, ngpiochips,
+				   sizeof(*gpio_ranges), GFP_KERNEL);
+	if (!gpio_chips || !gpio_ranges)
+		return -ENOMEM;
+
+	i = 0;
+	for_each_child_of_node(np, child) {
+		if (!of_property_read_bool(child, "gpio-controller"))
+			continue;
+
+		ret = rza1_parse_gpiochip(rza1_pctl, child, &gpio_chips[i],
+					  &gpio_ranges[i]);
+		if (ret)
+			goto gpiochip_remove;
+
+		++i;
+	}
+
+	dev_info(rza1_pctl->dev, "Registered %u gpio controllers\n", i);
+
+	return 0;
+
+gpiochip_remove:
+	for (; i > 0; i--)
+		devm_gpiochip_remove(rza1_pctl->dev, &gpio_chips[i - 1]);
+
+	return ret;
+}
+
+/**
+ * rza1_pinctrl_register() - Enumerate pins, ports and gpiochips; register
+ *			     them to pinctrl and gpio cores.
+ *
+ * @rza1_pctl: RZ/A1 pin controller device
+ */
+static int rza1_pinctrl_register(struct rza1_pinctrl *rza1_pctl)
+{
+	struct pinctrl_pin_desc *pins;
+	struct rza1_port *ports;
+	unsigned int i;
+	int ret;
+
+	pins = devm_kcalloc(rza1_pctl->dev, RZA1_NPINS, sizeof(*pins),
+			    GFP_KERNEL);
+	ports = devm_kcalloc(rza1_pctl->dev, RZA1_NPORTS, sizeof(*ports),
+			     GFP_KERNEL);
+	if (!pins || !ports)
+		return -ENOMEM;
+
+	rza1_pctl->pins		= pins;
+	rza1_pctl->desc.pins	= pins;
+	rza1_pctl->desc.npins	= RZA1_NPINS;
+	rza1_pctl->ports	= ports;
+
+	for (i = 0; i < RZA1_NPINS; ++i) {
+		unsigned int pin = RZA1_PIN_ID_TO_PIN(i);
+		unsigned int port = RZA1_PIN_ID_TO_PORT(i);
+
+		pins[i].number = i;
+		pins[i].name = devm_kasprintf(rza1_pctl->dev, GFP_KERNEL,
+					      "P%u-%u", port, pin);
+
+		if (i % RZA1_PINS_PER_PORT == 0) {
+			/*
+			 * Setup ports;
+			 * they provide per-port lock and logical base address.
+			 */
+			unsigned int port_id = RZA1_PIN_ID_TO_PORT(i);
+
+			ports[port_id].id	= port_id;
+			ports[port_id].base	= rza1_pctl->base;
+			ports[port_id].pins	= &pins[i];
+			spin_lock_init(&ports[port_id].lock);
+		}
+	}
+
+	ret = devm_pinctrl_register_and_init(rza1_pctl->dev, &rza1_pctl->desc,
+					     rza1_pctl, &rza1_pctl->pctl);
+	if (ret) {
+		dev_err(rza1_pctl->dev,
+			"RZ/A1 pin controller registration failed\n");
+		return ret;
+	}
+
+	ret = pinctrl_enable(rza1_pctl->pctl);
+	if (ret) {
+		dev_err(rza1_pctl->dev,
+			"RZ/A1 pin controller failed to start\n");
+		return ret;
+	}
+
+	ret = rza1_gpio_register(rza1_pctl);
+	if (ret) {
+		dev_err(rza1_pctl->dev, "RZ/A1 GPIO registration failed\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int rza1_pinctrl_probe(struct platform_device *pdev)
+{
+	struct rza1_pinctrl *rza1_pctl;
+	struct resource *res;
+	int ret;
+
+	rza1_pctl = devm_kzalloc(&pdev->dev, sizeof(*rza1_pctl), GFP_KERNEL);
+	if (!rza1_pctl)
+		return -ENOMEM;
+
+	rza1_pctl->dev = &pdev->dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (ret)
+		return -ENODEV;
+
+	rza1_pctl->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(rza1_pctl->base))
+		return PTR_ERR(rza1_pctl->base);
+
+	mutex_init(&rza1_pctl->mutex);
+
+	platform_set_drvdata(pdev, rza1_pctl);
+
+	rza1_pctl->desc.name	= DRIVER_NAME;
+	rza1_pctl->desc.pctlops	= &rza1_pinctrl_ops;
+	rza1_pctl->desc.pmxops	= &rza1_pinmux_ops;
+	rza1_pctl->desc.owner	= THIS_MODULE;
+	rza1_pctl->data		= of_device_get_match_data(&pdev->dev);
+
+	ret = rza1_pinctrl_register(rza1_pctl);
+	if (ret)
+		return ret;
+
+	dev_info(&pdev->dev,
+		 "RZ/A1 pin controller and gpio successfully registered\n");
+
+	return 0;
+}
+
+static const struct of_device_id rza1_pinctrl_of_match[] = {
+	{
+		.compatible	= "renesas,r7s72100-ports",
+		.data		= &rza1h_pmx_conf,
+	},
+	{ }
+};
+
+static struct platform_driver rza1_pinctrl_driver = {
+	.driver = {
+		.name = DRIVER_NAME,
+		.of_match_table = rza1_pinctrl_of_match,
+	},
+	.probe = rza1_pinctrl_probe,
+};
+
+static int __init rza1_pinctrl_init(void)
+{
+	return platform_driver_register(&rza1_pinctrl_driver);
+}
+core_initcall(rza1_pinctrl_init);
+
+MODULE_AUTHOR("Jacopo Mondi <jacopo+renesas@jmondi.org");
+MODULE_DESCRIPTION("Pin and gpio controller driver for Reneas RZ/A1 SoC");
+MODULE_LICENSE("GPL v2");
-- 
2.7.4

[PATCH v6 2/8] dt-bindings: pinctrl: Add RZ/A1 bindings doc

[Jacopo Mondi]

Add device tree bindings documentation for Renesas RZ/A1 gpio and pin
controller.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
 .../bindings/pinctrl/renesas,rza1-pinctrl.txt      | 221 +++++++++++++++++++++
 1 file changed, 221 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt

diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt
new file mode 100644
index 0000000..43e21474
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt
@@ -0,0 +1,221 @@
+Renesas RZ/A1 combined Pin and GPIO controller
+
+The Renesas SoCs of the RZ/A1 family feature a combined Pin and GPIO controller,
+named "Ports" in the hardware reference manual.
+Pin multiplexing and GPIO configuration is performed on a per-pin basis
+writing configuration values to per-port register sets.
+Each "port" features up to 16 pins, each of them configurable for GPIO
+function (port mode) or in alternate function mode.
+Up to 8 different alternate function modes exist for each single pin.
+
+Pin controller node
+-------------------
+
+Required properties:
+  - compatible
+    this shall be "renesas,r7s72100-ports".
+
+  - reg
+    address base and length of the memory area where the pin controller
+    hardware is mapped to.
+
+Example:
+Pin controller node for RZ/A1H SoC (r7s72100)
+
+pinctrl: pin-controller@fcfe3000 {
+	compatible = "renesas,r7s72100-ports";
+
+	reg = <0xfcfe3000 0x4230>;
+};
+
+Sub-nodes
+---------
+
+The child nodes of the pin controller node describe a pin multiplexing
+function or a GPIO controller alternatively.
+
+- Pin multiplexing sub-nodes:
+  A pin multiplexing sub-node describes how to configure a set of
+  (or a single) pin in some desired alternate function mode.
+  A single sub-node may define several pin configurations.
+  A few alternate function require special pin configuration flags to be
+  supplied along with the alternate function configuration number.
+  The hardware reference manual specifies when a pin function requires
+  "software IO driven" mode to be specified. To do so use the generic
+  properties from the <include/linux/pinctrl/pinconf_generic.h> header file
+  to instruct the pin controller to perform the desired pin configuration
+  operation.
+  Please refer to pinctrl-bindings.txt to get to know more on generic
+  pin properties usage.
+
+  The allowed generic formats for a pin multiplexing sub-node are the
+  following ones:
+
+  node-1 {
+      pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ;
+      GENERIC_PINCONFIG;
+  };
+
+  node-2 {
+      sub-node-1 {
+          pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ;
+          GENERIC_PINCONFIG;
+      };
+
+      sub-node-2 {
+          pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ;
+          GENERIC_PINCONFIG;
+      };
+
+      ...
+
+      sub-node-n {
+          pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ;
+          GENERIC_PINCONFIG;
+      };
+  };
+
+  Use the second format when pins part of the same logical group need to have
+  different generic pin configuration flags applied.
+
+  Client sub-nodes shall refer to pin multiplexing sub-nodes using the phandle
+  of the most external one.
+
+  Eg.
+
+  client-1 {
+      ...
+      pinctrl-0 = <&node-1>;
+      ...
+  };
+
+  client-2 {
+      ...
+      pinctrl-0 = <&node-2>;
+      ...
+  };
+
+  Required properties:
+    - pinmux:
+      integer array representing pin number and pin multiplexing configuration.
+      When a pin has to be configured in alternate function mode, use this
+      property to identify the pin by its global index, and provide its
+      alternate function configuration number along with it.
+      When multiple pins are required to be configured as part of the same
+      alternate function they shall be specified as members of the same
+      argument list of a single "pinmux" property.
+      Helper macros to ease assembling the pin index from its position
+      (port where it sits on and pin number) and alternate function identifier
+      are provided by the pin controller header file at:
+      <include/dt-bindings/pinctrl/r7s72100-pinctrl.h>
+      Integers values in "pinmux" argument list are assembled as:
+      ((PORT * 16 + PIN) | MUX_FUNC << 16)
+
+  Optional generic properties:
+    - input-enable:
+      enable input bufer for pins requiring software driven IO input
+      operations.
+    - output-high:
+      enable output buffer for pins requiring software driven IO output
+      operations. output-low can be used alternatively, as line value is
+      ignored by the driver.
+
+  The hardware reference manual specifies when a pin has to be configured to
+  work in bi-directional mode and when the IO direction has to be specified
+  by software. Bi-directional pins are managed by the pin controller driver
+  internally, while software driven IO direction has to be explicitly
+  selected when multiple options are available.
+
+  Example:
+  A serial communication interface with a TX output pin and an RX input pin.
+
+  &pinctrl {
+	scif2_pins: serial2 {
+		pinmux = <RZA1_PINMUX(3, 0, 6)>, <RZA1_PINMUX(3, 2, 4)>;
+	};
+  };
+
+  Pin #0 on port #3 is configured as alternate function #6.
+  Pin #2 on port #3 is configured as alternate function #4.
+
+  Example 2:
+  I2c master: both SDA and SCL pins need bi-directional operations
+
+  &pinctrl {
+	i2c2_pins: i2c2 {
+		pinmux = <RZA1_PINMUX(1, 4, 1)>, <RZA1_PINMUX(1, 5, 1)>;
+	};
+  };
+
+  Pin #4 on port #1 is configured as alternate function #1.
+  Pin #5 on port #1 is configured as alternate function #1.
+  Both need to work in bi-directional mode, the driver manages this internally.
+
+  Example 3:
+  Multi-function timer input and output compare pins.
+  Configure TIOC0A as software driven input and TIOC0B as software driven
+  output.
+
+  &pinctrl {
+	tioc0_pins: tioc0 {
+		tioc0_input_pins {
+			pinumx = <RZA1_PINMUX(4, 0, 2)>;
+			input-enable;
+		};
+
+		tioc0_output_pins {
+			pinmux = <RZA1_PINMUX(4, 1, 1)>;
+			output-enable;
+		};
+	};
+  };
+
+  &tioc0 {
+	...
+	pinctrl-0 = <&tioc0_pins>;
+	...
+  };
+
+  Pin #0 on port #4 is configured as alternate function #2 with IO direction
+  specified by software as input.
+  Pin #1 on port #4 is configured as alternate function #1 with IO direction
+  specified by software as output.
+
+- GPIO controller sub-nodes:
+  Each port of the r7s72100 pin controller hardware is itself a GPIO controller.
+  Different SoCs have different numbers of available pins per port, but
+  generally speaking, each of them can be configured in GPIO ("port") mode
+  on this hardware.
+  Describe GPIO controllers using sub-nodes with the following properties.
+
+  Required properties:
+    - gpio-controller
+      empty property as defined by the GPIO bindings documentation.
+    - #gpio-cells
+      number of cells required to identify and configure a GPIO.
+      Shall be 2.
+    - gpio-ranges
+      Describes a GPIO controller specifying its specific pin base, the pin
+      base in the global pin numbering space, and the number of controlled
+      pins, as defined by the GPIO bindings documentation. Refer to
+      Documentation/devicetree/bindings/gpio/gpio.txt file for a more detailed
+      description.
+
+  Example:
+  A GPIO controller node, controlling 16 pins indexed from 0.
+  The GPIO controller base in the global pin indexing space is pin 48, thus
+  pins [0 - 15] on this controller map to pins [48 - 63] in the global pin
+  indexing space.
+
+  port3: gpio-3 {
+	gpio-controller;
+	#gpio-cells = <2>;
+	gpio-ranges = <&pinctrl 0 48 16>;
+  };
+
+  A device node willing to use pins controlled by this GPIO controller, shall
+  refer to it as follows:
+
+  led1 {
+	gpios = <&port3 10 GPIO_ACTIVE_LOW>;
+  };
-- 
2.7.4

[PATCH v6 3/8] arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header

[Jacopo Mondi]

Add dt-bindings for Renesas r7s72100 pin controller header file.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
 include/dt-bindings/pinctrl/r7s72100-pinctrl.h | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
 create mode 100644 include/dt-bindings/pinctrl/r7s72100-pinctrl.h

diff --git a/include/dt-bindings/pinctrl/r7s72100-pinctrl.h b/include/dt-bindings/pinctrl/r7s72100-pinctrl.h
new file mode 100644
index 0000000..6b609fe
--- /dev/null
+++ b/include/dt-bindings/pinctrl/r7s72100-pinctrl.h
@@ -0,0 +1,16 @@
+/*
+ * Defines macros and constants for Renesas RZ/A1 pin controller pin
+ * muxing functions.
+ */
+#ifndef __DT_BINDINGS_PINCTRL_RENESAS_RZA1_H
+#define __DT_BINDINGS_PINCTRL_RENESAS_RZA1_H
+
+#define RZA1_PINS_PER_PORT	16
+
+/*
+ * Create the pin index from its bank and position numbers and store in
+ * the upper 16 bits the alternate function identifier
+ */
+#define RZA1_PINMUX(b, p, f)	((b) * RZA1_PINS_PER_PORT + (p) | (f << 16))
+
+#endif /* __DT_BINDINGS_PINCTRL_RENESAS_RZA1_H */
-- 
2.7.4

[PATCH v6 4/8] arm: dts: r7s72100: Add pin controller node

[Jacopo Mondi]

Add pin controller node with 12 gpio controller sub-nodes to
r7s72100 dtsi.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r7s72100.dtsi | 78 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 78 insertions(+)

diff --git a/arch/arm/boot/dts/r7s72100.dtsi b/arch/arm/boot/dts/r7s72100.dtsi
index 0423996..fb54cb5 100644
--- a/arch/arm/boot/dts/r7s72100.dtsi
+++ b/arch/arm/boot/dts/r7s72100.dtsi
@@ -207,6 +207,84 @@
 		};
 	};
 
+	pinctrl: pin-controller@fcfe3000 {
+		compatible = "renesas,r7s72100-ports";
+
+		reg = <0xfcfe3000 0x4230>;
+
+		port0: gpio-0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 0 6>;
+		};
+
+		port1: gpio-1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 16 16>;
+		};
+
+		port2: gpio-2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 32 16>;
+		};
+
+		port3: gpio-3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 48 16>;
+		};
+
+		port4: gpio-4 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 64 16>;
+		};
+
+		port5: gpio-5 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 80 11>;
+		};
+
+		port6: gpio-6 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 96 16>;
+		};
+
+		port7: gpio-7 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 112 16>;
+		};
+
+		port8: gpio-8 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 128 16>;
+		};
+
+		port9: gpio-9 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 144 8>;
+		};
+
+		port10: gpio-10 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 160 16>;
+		};
+
+		port11: gpio-11 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 176 16>;
+		};
+	};
+
 	scif0: serial@e8007000 {
 		compatible = "renesas,scif-r7s72100", "renesas,scif";
 		reg = <0xe8007000 64>;
-- 
2.7.4

[PATCH v6 5/8] arm: dts: genmai: Add SCIF2 pin group

[Jacopo Mondi]

Add pin configuration subnode for SCIF2 serial debug interface.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r7s72100-genmai.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/r7s72100-genmai.dts b/arch/arm/boot/dts/r7s72100-genmai.dts
index 52a7b58..af2083f 100644
--- a/arch/arm/boot/dts/r7s72100-genmai.dts
+++ b/arch/arm/boot/dts/r7s72100-genmai.dts
@@ -11,6 +11,7 @@
 
 /dts-v1/;
 #include "r7s72100.dtsi"
+#include <dt-bindings/pinctrl/r7s72100-pinctrl.h>
 
 / {
 	model = "Genmai";
@@ -36,6 +37,14 @@
 	};
 };
 
+&pinctrl {
+
+	scif2_pins: serial2 {
+		/* P3_0 as TxD2; P3_2 as RxD2 */
+		pinmux = <RZA1_PINMUX(3, 0, 6)>, <RZA1_PINMUX(3, 2, 4)>;
+	};
+};
+
 &extal_clk {
 	clock-frequency = <13330000>;
 };
@@ -68,6 +77,9 @@
 };
 
 &scif2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&scif2_pins>;
+
 	status = "okay";
 };
 
-- 
2.7.4

[PATCH v6 6/8] arm: dts: genmai: Add RIIC2 pin group

[Jacopo Mondi]

Add pin configuration subnode for RIIC2 interface.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r7s72100-genmai.dts | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/r7s72100-genmai.dts b/arch/arm/boot/dts/r7s72100-genmai.dts
index af2083f..8b41d83 100644
--- a/arch/arm/boot/dts/r7s72100-genmai.dts
+++ b/arch/arm/boot/dts/r7s72100-genmai.dts
@@ -43,6 +43,11 @@
 		/* P3_0 as TxD2; P3_2 as RxD2 */
 		pinmux = <RZA1_PINMUX(3, 0, 6)>, <RZA1_PINMUX(3, 2, 4)>;
 	};
+
+	i2c2_pins: i2c2 {
+		/* RIIC2: P1_4 as SCL, P1_5 as SDA */
+		pinmux = <RZA1_PINMUX(1, 4, 1)>, <RZA1_PINMUX(1, 5, 1)>;
+	};
 };
 
 &extal_clk {
@@ -65,6 +70,9 @@
 	status = "okay";
 	clock-frequency = <400000>;
 
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
 	eeprom@50 {
 		compatible = "renesas,24c128";
 		reg = <0x50>;
-- 
2.7.4

[PATCH v6 7/8] arm: dts: genmai: Add user led device nodes

[Jacopo Mondi]

Add device nodes for user leds on Genmai board.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r7s72100-genmai.dts | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm/boot/dts/r7s72100-genmai.dts b/arch/arm/boot/dts/r7s72100-genmai.dts
index 8b41d83..8e6157b 100644
--- a/arch/arm/boot/dts/r7s72100-genmai.dts
+++ b/arch/arm/boot/dts/r7s72100-genmai.dts
@@ -11,6 +11,7 @@
 
 /dts-v1/;
 #include "r7s72100.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/r7s72100-pinctrl.h>
 
 / {
@@ -35,6 +36,19 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 	};
+
+	leds {
+		status = "okay";
+		compatible = "gpio-leds";
+
+		led1 {
+			gpios = <&port4 10 GPIO_ACTIVE_LOW>;
+		};
+
+		led2 {
+			gpios = <&port4 11 GPIO_ACTIVE_LOW>;
+		};
+	};
 };
 
 &pinctrl {
-- 
2.7.4

[PATCH v6 8/8] arm: dts: genmai: Add ethernet pin group

[Jacopo Mondi]

Add pin configuration subnode for ETHER ethernet controller.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
 arch/arm/boot/dts/r7s72100-genmai.dts | 35 +++++++++++++++++++++++++++++++++++
 1 file changed, 35 insertions(+)

diff --git a/arch/arm/boot/dts/r7s72100-genmai.dts b/arch/arm/boot/dts/r7s72100-genmai.dts
index 8e6157b..4d0b68c 100644
--- a/arch/arm/boot/dts/r7s72100-genmai.dts
+++ b/arch/arm/boot/dts/r7s72100-genmai.dts
@@ -62,6 +62,28 @@
 		/* RIIC2: P1_4 as SCL, P1_5 as SDA */
 		pinmux = <RZA1_PINMUX(1, 4, 1)>, <RZA1_PINMUX(1, 5, 1)>;
 	};
+
+	ether_pins: ether {
+		/* Ethernet on Ports 1,2,3,5 */
+		pinmux = <RZA1_PINMUX(1, 14, 4)>,/* P1_14 = ET_COL  */
+			 <RZA1_PINMUX(5, 9, 2)>, /* P5_9 = ET_MDC   */
+			 <RZA1_PINMUX(3, 3, 2)>, /* P3_3 = ET_MDIO */
+			 <RZA1_PINMUX(3, 4, 2)>, /* P3_4 = ET_RXCLK */
+			 <RZA1_PINMUX(3, 5, 2)>, /* P3_5 = ET_RXER  */
+			 <RZA1_PINMUX(3, 6, 2)>, /* P3_6 = ET_RXDV  */
+			 <RZA1_PINMUX(2, 0, 2)>, /* P2_0 = ET_TXCLK */
+			 <RZA1_PINMUX(2, 1, 2)>, /* P2_1 = ET_TXER  */
+			 <RZA1_PINMUX(2, 2, 2)>, /* P2_2 = ET_TXEN  */
+			 <RZA1_PINMUX(2, 3, 2)>, /* P2_3 = ET_CRS   */
+			 <RZA1_PINMUX(2, 4, 2)>, /* P2_4 = ET_TXD0  */
+			 <RZA1_PINMUX(2, 5, 2)>, /* P2_5 = ET_TXD1  */
+			 <RZA1_PINMUX(2, 6, 2)>, /* P2_6 = ET_TXD2  */
+			 <RZA1_PINMUX(2, 7, 2)>, /* P2_7 = ET_TXD3  */
+			 <RZA1_PINMUX(2, 8, 2)>, /* P2_8 = ET_RXD0  */
+			 <RZA1_PINMUX(2, 9, 2)>, /* P2_9 = ET_RXD1  */
+			 <RZA1_PINMUX(2, 10, 2)>,/* P2_10 = ET_RXD2 */
+			 <RZA1_PINMUX(2, 11, 2)>;/* P2_11 = ET_RXD3 */
+	};
 };
 
 &extal_clk {
@@ -80,6 +102,19 @@
 	status = "okay";
 };
 
+&ether {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ether_pins>;
+
+	status = "okay";
+
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
 &i2c2 {
 	status = "okay";
 	clock-frequency = <400000>;
-- 
2.7.4

Re: [PATCH v6 2/8] dt-bindings: pinctrl: Add RZ/A1 bindings doc

[Rob Herring]

On Thu, Jun 22, 2017 at 04:54:30PM +0200, Jacopo Mondi wrote:
> Add device tree bindings documentation for Renesas RZ/A1 gpio and pin
> controller.
> 
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> ---
>  .../bindings/pinctrl/renesas,rza1-pinctrl.txt      | 221 +++++++++++++++++++++
>  1 file changed, 221 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt

Please add acks when posting new versions. It seems there are 2 more 
lines here, but I have no idea what changed. I'm assuming it was minor 
enough to retain my ack.

Rob

Re: [PATCH v6 2/8] dt-bindings: pinctrl: Add RZ/A1 bindings doc

[jmondi]

Hi Rob,

On Thu, Jun 22, 2017 at 04:09:17PM -0500, Rob Herring wrote:
> On Thu, Jun 22, 2017 at 04:54:30PM +0200, Jacopo Mondi wrote:
> > Add device tree bindings documentation for Renesas RZ/A1 gpio and pin
> > controller.
> >
> > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> > ---
> >  .../bindings/pinctrl/renesas,rza1-pinctrl.txt      | 221 +++++++++++++++++++++
> >  1 file changed, 221 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt
>
> Please add acks when posting new versions. It seems there are 2 more
> lines here, but I have no idea what changed. I'm assuming it was minor
> enough to retain my ack.

I have dropped your Acked-by in v4, as compared to the previous
versions bindings changed "significantly".
Quoting the v4 cover letter:

"The device tree bindings changed significantly, and as anticipated I
have not incorporated Rob's ack as I would like him to have a look there again."

Now that I look at bindings again, I guess I could have kept it
because all of the changes are related to pin controller subsystem
specificities and are not that "significant" in the end..

I'll list them here for your reference

- use "pinmux" in place of "renesas,pins" property
- use generic properties in place of pin mux flags
- a bit of shuffling on generic properties in v4->v6 transition

If none of these is relevant to you, we can add you Acked-by back when
sending pull-request (right Geert?)

Thanks
   j

>
> Rob

Re: [PATCH v6 00/8] Renesas RZ/A1 pin and gpio controller

[Geert Uytterhoeven]

Hi Linus,

On Thu, Jun 22, 2017 at 4:54 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
>    this is 6th round of RZ/A1 pin controller patch series.
>
> Where did we stop: discussion from pin controller driver shifted toward two
> new generic pin configuration properties I added to the previous series
> (bi-directional and output-enable).
>
> After a really long discussion, we decided to go for handling internally all
> bi-directional use cases, making the generic property not a requirement for the
> series. Interestingly, we recently found out the number of pins actually
> requiring this flag is less (~half) than what reported by the processor manual,
> so we could have handled these internally from day one :(
>
> We also now manage internally pins requiring IO direction specified in software
> even when configured in alternate function mode (SWIO mode). Most of them are
> handled by the driver, some of them have to come from DTS as the user can freely
> select if they have to be inputs or outputs. For those pins, and after another
> discussion involving NXP developers, we decided to use input-enable and
> output-enable properties. I have just sent a patch to add output-enable to the
> generic pin configuration properties, but it is currently under discussion.
>
> However, none of the pins currently configured by mainline DTS require those
> properties to be specified, so I have dropped in this driver any dependency on
> output-enable property, and I'm using instead the already in place
> PIN_CONFIG_OUTPUT one. Once output-enable will eventually be accepted, we can
> update the driver to make use of it, but since there are no use cases for that
> at the moment, it makes not too much sense holding this series back for that.
>
> The total memory occupation we were so worried about of bi-directional and swio
> pin tables is now around 100 bytes, because of how the number of pins actually
> needing those flags has  reduced and because of how we have arranged the
> tables using bitfield structures (credits to Geert here).
>
> Having cleared out dependencies on new pin configuration properties and having
> made configuration flags a driver specific issue, I hope this version can be
> accepted and land in forthcoming pull request for Renesas PFC updates from
> Geert, pending some feedback from the linux-gpio community.

If this is OK for you, I'd like to include the first 3 patches (plus a small
fix I received offline from Chris Brandt[*]) in my final pull request of
sh-pfc for v4.13 (which I have been postponing in anticipation of this driver).

After v4.13-rc1, Simon can queue up the DTS patches in his tree for v4.14.

Thanks!

[*]

--- a/drivers/pinctrl/pinctrl-rza1.c
+++ b/drivers/pinctrl/pinctrl-rza1.c
@@ -617,11 +617,13 @@ static int rza1_pin_mux_single(struct
rza1_pinctrl *rza1_pctl,
         * to I/O direction specified by pin configuration -after- PMC has been
         * set to one.
         */
-       if (!(mux_flags & (MUX_FLAGS_SWIO_INPUT | MUX_FLAGS_SWIO_OUTPUT)))
+       if (mux_flags & (MUX_FLAGS_SWIO_INPUT | MUX_FLAGS_SWIO_OUTPUT))
+               rza1_set_bit(port, RZA1_PM_REG, pin,
+                            mux_flags & MUX_FLAGS_SWIO_INPUT);
+       else
                rza1_set_bit(port, RZA1_PIPC_REG, pin, 1);

        rza1_set_bit(port, RZA1_PMC_REG, pin, 1);
-       rza1_set_bit(port, RZA1_PM_REG, pin, mux_flags & MUX_FLAGS_SWIO_INPUT);

        return 0;
 }

> v1 -> v2:
> - change pin configuration flags as suggested by Chris
> - gpio set direction function fixed as suggested by Chris
> - add some more example on pin configuration flag usage to dt-binding doc
> - fix gpio-controller names to remove unit address as suggested by Geert
> - some comments chopped here and there to make the driver less verbose
>
> v2 -> v3:
> - fix grammar and syntax in comment and documentation
> - fix code style (reverse xmas tree ordering in variable declaration)
> - use irqsave/irqrestore in spinlock lock/unlock
> - use devm_ version of kasprintf (memory returned was not properly free)
> - use bitops.h operation ffs and fls to make sure a single bit is set in pmx
>   mask
> - Add Geert's reviewed-by to DTS patches
>
> v3 -> v4:
> - use "pinmux" property in pmx sub-nodes in place of "renesas,pins"
> - use pinconf standard properties to set pin mux additional flags
> - add "bi-directional" and "output-enable" to pinconf generic properties
> - perform pmx function parsing at dt_node_to_map() time
> - change DT bindings to use GENERIC_PINCONF
> - change DT bindings to allow sub-nodes to have "pinmux" property specified
> - several renames (register names, DT parse functions, set_mux() function)
>
> v4 -> v5:
> - use pinctrl_enable() function in pin controller registration function
> - update bindings documentation to incorporate Geert's comments
> - add generic properties unpack macros
>
> v5 -> v6:
> - add tables in driver to manage bi-directional and swio flags
> - drop dependecies on new generic pin configuration properties
>
> Jacopo Mondi (8):
>   pinctrl: Renesas RZ/A1 pin and gpio controller
>   dt-bindings: pinctrl: Add RZ/A1 bindings doc
>   arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
>   arm: dts: r7s72100: Add pin controller node
>   arm: dts: genmai: Add SCIF2 pin group
>   arm: dts: genmai: Add RIIC2 pin group
>   arm: dts: genmai: Add user led device nodes
>   arm: dts: genmai: Add ethernet pin group
>
>  .../bindings/pinctrl/renesas,rza1-pinctrl.txt      |  218 ++++
>  arch/arm/boot/dts/r7s72100-genmai.dts              |   69 ++
>  arch/arm/boot/dts/r7s72100.dtsi                    |   78 ++
>  drivers/pinctrl/Kconfig                            |   11 +
>  drivers/pinctrl/Makefile                           |    1 +
>  drivers/pinctrl/pinctrl-rza1.c                     | 1309 ++++++++++++++++++++
>  include/dt-bindings/pinctrl/r7s72100-pinctrl.h     |   16 +
>  7 files changed, 1702 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt
>  create mode 100644 drivers/pinctrl/pinctrl-rza1.c
>  create mode 100644 include/dt-bindings/pinctrl/r7s72100-pinctrl.h

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH v6 00/8] Renesas RZ/A1 pin and gpio controller

[Simon Horman]

On Mon, Jun 26, 2017 at 10:45:22AM +0200, Geert Uytterhoeven wrote:
> Hi Linus,
> 
> On Thu, Jun 22, 2017 at 4:54 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
> >    this is 6th round of RZ/A1 pin controller patch series.
> >
> > Where did we stop: discussion from pin controller driver shifted toward two
> > new generic pin configuration properties I added to the previous series
> > (bi-directional and output-enable).
> >
> > After a really long discussion, we decided to go for handling internally all
> > bi-directional use cases, making the generic property not a requirement for the
> > series. Interestingly, we recently found out the number of pins actually
> > requiring this flag is less (~half) than what reported by the processor manual,
> > so we could have handled these internally from day one :(
> >
> > We also now manage internally pins requiring IO direction specified in software
> > even when configured in alternate function mode (SWIO mode). Most of them are
> > handled by the driver, some of them have to come from DTS as the user can freely
> > select if they have to be inputs or outputs. For those pins, and after another
> > discussion involving NXP developers, we decided to use input-enable and
> > output-enable properties. I have just sent a patch to add output-enable to the
> > generic pin configuration properties, but it is currently under discussion.
> >
> > However, none of the pins currently configured by mainline DTS require those
> > properties to be specified, so I have dropped in this driver any dependency on
> > output-enable property, and I'm using instead the already in place
> > PIN_CONFIG_OUTPUT one. Once output-enable will eventually be accepted, we can
> > update the driver to make use of it, but since there are no use cases for that
> > at the moment, it makes not too much sense holding this series back for that.
> >
> > The total memory occupation we were so worried about of bi-directional and swio
> > pin tables is now around 100 bytes, because of how the number of pins actually
> > needing those flags has  reduced and because of how we have arranged the
> > tables using bitfield structures (credits to Geert here).
> >
> > Having cleared out dependencies on new pin configuration properties and having
> > made configuration flags a driver specific issue, I hope this version can be
> > accepted and land in forthcoming pull request for Renesas PFC updates from
> > Geert, pending some feedback from the linux-gpio community.
> 
> If this is OK for you, I'd like to include the first 3 patches (plus a small
> fix I received offline from Chris Brandt[*]) in my final pull request of
> sh-pfc for v4.13 (which I have been postponing in anticipation of this driver).
> 
> After v4.13-rc1, Simon can queue up the DTS patches in his tree for v4.14.

Fine by me.

I have marked the dts patches as Deferred.
Jacopo, please repost or ping me once the driver changes have shown
up in an rc release - v4.13-rc1 sounds likely.

Re: [PATCH v6 00/8] Renesas RZ/A1 pin and gpio controller

[Geert Uytterhoeven]

Hi Linus,

On Mon, Jun 26, 2017 at 10:45 AM, Geert Uytterhoeven
<geert@linux-m68k.org> wrote:
> On Thu, Jun 22, 2017 at 4:54 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
>>    this is 6th round of RZ/A1 pin controller patch series.
>>
>> Where did we stop: discussion from pin controller driver shifted toward two
>> new generic pin configuration properties I added to the previous series
>> (bi-directional and output-enable).
>>
>> After a really long discussion, we decided to go for handling internally all
>> bi-directional use cases, making the generic property not a requirement for the
>> series. Interestingly, we recently found out the number of pins actually
>> requiring this flag is less (~half) than what reported by the processor manual,
>> so we could have handled these internally from day one :(
>>
>> We also now manage internally pins requiring IO direction specified in software
>> even when configured in alternate function mode (SWIO mode). Most of them are
>> handled by the driver, some of them have to come from DTS as the user can freely
>> select if they have to be inputs or outputs. For those pins, and after another
>> discussion involving NXP developers, we decided to use input-enable and
>> output-enable properties. I have just sent a patch to add output-enable to the
>> generic pin configuration properties, but it is currently under discussion.
>>
>> However, none of the pins currently configured by mainline DTS require those
>> properties to be specified, so I have dropped in this driver any dependency on
>> output-enable property, and I'm using instead the already in place
>> PIN_CONFIG_OUTPUT one. Once output-enable will eventually be accepted, we can
>> update the driver to make use of it, but since there are no use cases for that
>> at the moment, it makes not too much sense holding this series back for that.
>>
>> The total memory occupation we were so worried about of bi-directional and swio
>> pin tables is now around 100 bytes, because of how the number of pins actually
>> needing those flags has  reduced and because of how we have arranged the
>> tables using bitfield structures (credits to Geert here).
>>
>> Having cleared out dependencies on new pin configuration properties and having
>> made configuration flags a driver specific issue, I hope this version can be
>> accepted and land in forthcoming pull request for Renesas PFC updates from
>> Geert, pending some feedback from the linux-gpio community.
>
> If this is OK for you, I'd like to include the first 3 patches (plus a small
> fix I received offline from Chris Brandt[*]) in my final pull request of
> sh-pfc for v4.13 (which I have been postponing in anticipation of this driver).

And so I did. Queued in sh-pfc-for-v4.13, pull request sent.

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH v6 00/8] Renesas RZ/A1 pin and gpio controller

[Simon Horman]

On Wed, Jun 28, 2017 at 07:36:15PM +0200, Geert Uytterhoeven wrote:
> Hi Linus,
> 
> On Mon, Jun 26, 2017 at 10:45 AM, Geert Uytterhoeven
> <geert@linux-m68k.org> wrote:
> > On Thu, Jun 22, 2017 at 4:54 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
> >>    this is 6th round of RZ/A1 pin controller patch series.
> >>
> >> Where did we stop: discussion from pin controller driver shifted toward two
> >> new generic pin configuration properties I added to the previous series
> >> (bi-directional and output-enable).
> >>
> >> After a really long discussion, we decided to go for handling internally all
> >> bi-directional use cases, making the generic property not a requirement for the
> >> series. Interestingly, we recently found out the number of pins actually
> >> requiring this flag is less (~half) than what reported by the processor manual,
> >> so we could have handled these internally from day one :(
> >>
> >> We also now manage internally pins requiring IO direction specified in software
> >> even when configured in alternate function mode (SWIO mode). Most of them are
> >> handled by the driver, some of them have to come from DTS as the user can freely
> >> select if they have to be inputs or outputs. For those pins, and after another
> >> discussion involving NXP developers, we decided to use input-enable and
> >> output-enable properties. I have just sent a patch to add output-enable to the
> >> generic pin configuration properties, but it is currently under discussion.
> >>
> >> However, none of the pins currently configured by mainline DTS require those
> >> properties to be specified, so I have dropped in this driver any dependency on
> >> output-enable property, and I'm using instead the already in place
> >> PIN_CONFIG_OUTPUT one. Once output-enable will eventually be accepted, we can
> >> update the driver to make use of it, but since there are no use cases for that
> >> at the moment, it makes not too much sense holding this series back for that.
> >>
> >> The total memory occupation we were so worried about of bi-directional and swio
> >> pin tables is now around 100 bytes, because of how the number of pins actually
> >> needing those flags has  reduced and because of how we have arranged the
> >> tables using bitfield structures (credits to Geert here).
> >>
> >> Having cleared out dependencies on new pin configuration properties and having
> >> made configuration flags a driver specific issue, I hope this version can be
> >> accepted and land in forthcoming pull request for Renesas PFC updates from
> >> Geert, pending some feedback from the linux-gpio community.
> >
> > If this is OK for you, I'd like to include the first 3 patches (plus a small
> > fix I received offline from Chris Brandt[*]) in my final pull request of
> > sh-pfc for v4.13 (which I have been postponing in anticipation of this driver).
> 
> And so I did. Queued in sh-pfc-for-v4.13, pull request sent.

I have applied up the dts changes on top of v4.13-rc1.