[PATCH v5 0/2] ARM: dts: am3355: add support for the Sancloud Beaglebone Enhanced

[PATCH v5 0/2] ARM: dts: am3355: add support for the Sancloud Beaglebone Enhanced

[Koen Kooi]

The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:

 * Gigabit capable PHY
 * Extra USB hub, optional i2c control
 * lps3331ap barometer connected over i2c
 * MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
 * 1GiB DDR3 RAM
 * RTL8723 Wifi/Bluetooth connected over USB

This series adds the Sancloud vendor prefix as well as the actual dts.

v5: Generic nodenames, lowercase hex numbers
v4: Add Robs Acked-by for 1/2
v3: Drop 1GHz Opp tweak
v2: * Add missing #include <dt-bindings/interrupt-controller/irq.h>
    * Fix barometer compatible string
v1: Initial submission, not the dts actually tested :/

Also double checked if the kbuild error has been fixed:

koen@beast:/build/pkg/linux-torvalds$ git describe
v5.18-rc4-71-gd69088d
koen@beast:/build/pkg/linux-torvalds$ ARCH=arm CROSS_COMPILE=arm-angstrom-linux-gnueabi- make am335x-sancloud-bbe.dtb
  DTC     arch/arm/boot/dts/am335x-sancloud-bbe.dtb
koen@beast:/build/pkg/linux-torvalds$ 

Same successful result on tmlind/for-next (which has v2 already) and robh/for-next

Koen Kooi (2):
  dt-bindings: Add vendor prefix for Sancloud
  ARM: dts: am335x: add am335x-sancloud-bbe board support

 .../devicetree/bindings/vendor-prefixes.txt        |   1 +
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/am335x-sancloud-bbe.dts          | 146 +++++++++++++++++++++
 3 files changed, 148 insertions(+)
 create mode 100644 arch/arm/boot/dts/am335x-sancloud-bbe.dts

-- 
2.0.1

[PATCH v5 1/2] dt-bindings: Add vendor prefix for Sancloud

[Koen Kooi]

Add vendor prefix for Sancloud Ltd.

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Acked-by: Rob Herring <robh@kernel.org>
---

v5: No changes
v4: Add Acked-by
v3: No changes
v2: No changes
v1: Initial submission

 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 7cad066..c7aaa1f 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -314,6 +314,7 @@ rohm	ROHM Semiconductor Co., Ltd
 roofull	Shenzhen Roofull Technology Co, Ltd
 samsung	Samsung Semiconductor
 samtec	Samtec/Softing company
+sancloud	Sancloud Ltd
 sandisk	Sandisk Corporation
 sbs	Smart Battery System
 schindler	Schindler
-- 
2.0.1

[PATCH v5 2/2] ARM: dts: am335x: add am335x-sancloud-bbe board support

[Koen Kooi]

The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:

 * Gigabit capable PHY
 * Extra USB hub, optional i2c control
 * lps3331ap barometer connected over i2c
 * MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
 * 1GiB DDR3 RAM
 * RTL8723 Wifi/Bluetooth connected over USB

Tested on a revision G board.

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
---
v5: generic nodenames (e.g. mpu6050 -> accelerometer), lowercase hex numbers
v4: No changes
v3: Drop oppnitro-1000000000, not needed on the versions Sancloud is using
v2: * Add missing #include <dt-bindings/interrupt-controller/irq.h>
    * Fix Barometer compatible string
v1: Initial submission

 arch/arm/boot/dts/Makefile                |   1 +
 arch/arm/boot/dts/am335x-sancloud-bbe.dts | 136 ++++++++++++++++++++++++++++++
 2 files changed, 137 insertions(+)
 create mode 100644 arch/arm/boot/dts/am335x-sancloud-bbe.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 37a3de7..83a4d61 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -695,6 +695,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-pepper.dtb \
 	am335x-phycore-rdk.dtb \
 	am335x-pocketbeagle.dtb \
+	am335x-sancloud-bbe.dtb \
 	am335x-shc.dtb \
 	am335x-sbc-t335.dtb \
 	am335x-sl50.dtb \
diff --git a/arch/arm/boot/dts/am335x-sancloud-bbe.dts b/arch/arm/boot/dts/am335x-sancloud-bbe.dts
new file mode 100644
index 0000000..7f8d068
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-sancloud-bbe.dts
@@ -0,0 +1,136 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-boneblack-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "SanCloud BeagleBone Enhanced";
+	compatible = "sancloud,am335x-boneenhanced", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+};
+
+&am33xx_pinmux {
+	pinctrl-names = "default";
+
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txen.rgmii1_tctl */
+			AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxdv.rgmii1_rctl */
+			AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd3.rgmii1_td3 */
+			AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd2.rgmii1_td2 */
+			AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd1.rgmii1_td1 */
+			AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd0.rgmii1_td0 */
+			AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txclk.rgmii1_tclk */
+			AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxclk.rgmii1_rclk */
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd3.rgmii1_rd3 */
+			AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd2.rgmii1_rd2 */
+			AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd1.rgmii1_rd1 */
+			AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd0.rgmii1_rd0 */
+		>;
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			/* MDIO */
+			AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+			AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
+		>;
+	};
+
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	usb_hub_ctrl: usb_hub_ctrl {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x944, PIN_OUTPUT_PULLUP | MUX_MODE7)     /* rmii1_refclk.gpio0_29 */
+		>;
+	};
+
+	mpu6050_pins: pinmux_mpu6050_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x968, PIN_INPUT | MUX_MODE7)    /* uart0_ctsn.gpio1_8 */
+		>;
+	};
+
+	lps3331ap_pins: pinmux_lps3331ap_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x868, PIN_INPUT | MUX_MODE7)     /* gpmc_a10.gpio1_26 */
+		>;
+	};
+};
+
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+	phy-mode = "rgmii-txid";
+};
+
+&i2c0 {
+	lps331ap: barometer@5c {
+		compatible = "st,lps331ap-press";
+		st,drdy-int-pin = <1>;
+		reg = <0x5c>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+	};
+
+	mpu6050: accelerometer@68 {
+		compatible = "invensense,mpu6050";
+		reg = <0x68>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
+		orientation = <0xff 0 0 0 1 0 0 0 0xff>;
+	};
+
+	usb2512b@2c {
+		compatible = "microchip,usb2512b";
+		reg = <0x2c>;
+		reset-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+		/* wifi on port 4 */
+	};
+};
-- 
2.0.1

Re: [PATCH v5 2/2] ARM: dts: am335x: add am335x-sancloud-bbe board support

[Tony Lindgren]

* Koen Kooi <koen@dominion.thruhere.net> [180717 06:28]:
> +&i2c0 {
> +	lps331ap: barometer@5c {
> +		compatible = "st,lps331ap-press";
> +		st,drdy-int-pin = <1>;
> +		reg = <0x5c>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <26 IRQ_TYPE_EDGE_RISING>;
> +	};
> +
> +	mpu6050: accelerometer@68 {
> +		compatible = "invensense,mpu6050";
> +		reg = <0x68>;
> +		interrupt-parent = <&gpio0>;
> +		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
> +		orientation = <0xff 0 0 0 1 0 0 0 0xff>;
> +	};
> +
> +	usb2512b@2c {
> +		compatible = "microchip,usb2512b";
> +		reg = <0x2c>;
> +		reset-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
> +		/* wifi on port 4 */
> +	};
> +};

Thanks for updating it, should the last one be usb-hub@2c?

Regards,

Tony

Re: [PATCH v5 2/2] ARM: dts: am335x: add am335x-sancloud-bbe board support

[Koen Kooi]

> Op 17 jul. 2018, om 08:36 heeft Tony Lindgren <tony@atomide.com> het volgende geschreven:
> 
> * Koen Kooi <koen@dominion.thruhere.net> [180717 06:28]:
>> +&i2c0 {
>> +	lps331ap: barometer@5c {
>> +		compatible = "st,lps331ap-press";
>> +		st,drdy-int-pin = <1>;
>> +		reg = <0x5c>;
>> +		interrupt-parent = <&gpio1>;
>> +		interrupts = <26 IRQ_TYPE_EDGE_RISING>;
>> +	};
>> +
>> +	mpu6050: accelerometer@68 {
>> +		compatible = "invensense,mpu6050";
>> +		reg = <0x68>;
>> +		interrupt-parent = <&gpio0>;
>> +		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
>> +		orientation = <0xff 0 0 0 1 0 0 0 0xff>;
>> +	};
>> +
>> +	usb2512b@2c {
>> +		compatible = "microchip,usb2512b";
>> +		reg = <0x2c>;
>> +		reset-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
>> +		/* wifi on port 4 */
>> +	};
>> +};
> 
> Thanks for updating it, should the last one be usb-hub@2c?

Yes, it should be. Never update patches halfway through your first morning coffee :) V6 coming up!

regards,

Koen

Re: [PATCH v5 1/2] dt-bindings: Add vendor prefix for Sancloud

[Alexandre Belloni]

Hi Koen,

I'm not sure how you expect that to be merged but you should probably
send this patch to the TI maintainers along 2/2 because probably no one
in copy of this patch will apply it.

On 17/07/2018 08:24:45+0200, Koen Kooi wrote:
> Add vendor prefix for Sancloud Ltd.
> 
> Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
> Acked-by: Rob Herring <robh@kernel.org>
> ---
> 
> v5: No changes
> v4: Add Acked-by
> v3: No changes
> v2: No changes
> v1: Initial submission
> 
>  Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index 7cad066..c7aaa1f 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -314,6 +314,7 @@ rohm	ROHM Semiconductor Co., Ltd
>  roofull	Shenzhen Roofull Technology Co, Ltd
>  samsung	Samsung Semiconductor
>  samtec	Samtec/Softing company
> +sancloud	Sancloud Ltd
>  sandisk	Sandisk Corporation
>  sbs	Smart Battery System
>  schindler	Schindler
> -- 
> 2.0.1
> 

-- 
Alexandre Belloni, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com

Re: [PATCH v5 1/2] dt-bindings: Add vendor prefix for Sancloud

[Koen Kooi]

> Op 17 jul. 2018, om 09:20 heeft Alexandre Belloni <alexandre.belloni@bootlin.com> het volgende geschreven:
> 
> Hi Koen,
> 
> I'm not sure how you expect that to be merged but you should probably
> send this patch to the TI maintainers along 2/2 because probably no one
> in copy of this patch will apply it.

Is that the linux-omap list and Tony? scripts/get_maintainer.pl didn’t pick them up, which is why they are missing.

regards,

Koen

> 
> On 17/07/2018 08:24:45+0200, Koen Kooi wrote:
>> Add vendor prefix for Sancloud Ltd.
>> 
>> Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
>> Acked-by: Rob Herring <robh@kernel.org>
>> ---
>> 
>> v5: No changes
>> v4: Add Acked-by
>> v3: No changes
>> v2: No changes
>> v1: Initial submission
>> 
>> Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
>> 1 file changed, 1 insertion(+)
>> 
>> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
>> index 7cad066..c7aaa1f 100644
>> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
>> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
>> @@ -314,6 +314,7 @@ rohm	ROHM Semiconductor Co., Ltd
>> roofull	Shenzhen Roofull Technology Co, Ltd
>> samsung	Samsung Semiconductor
>> samtec	Samtec/Softing company
>> +sancloud	Sancloud Ltd
>> sandisk	Sandisk Corporation
>> sbs	Smart Battery System
>> schindler	Schindler
>> -- 
>> 2.0.1
>> 
> 
> -- 
> Alexandre Belloni, Bootlin (formerly Free Electrons)
> Embedded Linux and Kernel engineering
> https://bootlin.com

Re: [PATCH v5 1/2] dt-bindings: Add vendor prefix for Sancloud

[Alexandre Belloni]

On 17/07/2018 09:31:15+0200, Koen Kooi wrote:
> 
> 
> > Op 17 jul. 2018, om 09:20 heeft Alexandre Belloni <alexandre.belloni@bootlin.com> het volgende geschreven:
> > 
> > Hi Koen,
> > 
> > I'm not sure how you expect that to be merged but you should probably
> > send this patch to the TI maintainers along 2/2 because probably no one
> > in copy of this patch will apply it.
> 
> Is that the linux-omap list and Tony? scripts/get_maintainer.pl didn’t pick them up, which is why they are missing.
> 

Yes, basically the same people that will apply the DT making use of this
vendor prefix so both patches go in at the same time.

> regards,
> 
> Koen
> 
> > 
> > On 17/07/2018 08:24:45+0200, Koen Kooi wrote:
> >> Add vendor prefix for Sancloud Ltd.
> >> 
> >> Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
> >> Acked-by: Rob Herring <robh@kernel.org>
> >> ---
> >> 
> >> v5: No changes
> >> v4: Add Acked-by
> >> v3: No changes
> >> v2: No changes
> >> v1: Initial submission
> >> 
> >> Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
> >> 1 file changed, 1 insertion(+)
> >> 
> >> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> >> index 7cad066..c7aaa1f 100644
> >> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> >> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> >> @@ -314,6 +314,7 @@ rohm	ROHM Semiconductor Co., Ltd
> >> roofull	Shenzhen Roofull Technology Co, Ltd
> >> samsung	Samsung Semiconductor
> >> samtec	Samtec/Softing company
> >> +sancloud	Sancloud Ltd
> >> sandisk	Sandisk Corporation
> >> sbs	Smart Battery System
> >> schindler	Schindler
> >> -- 
> >> 2.0.1
> >> 
> > 
> > -- 
> > Alexandre Belloni, Bootlin (formerly Free Electrons)
> > Embedded Linux and Kernel engineering
> > https://bootlin.com
> 

-- 
Alexandre Belloni, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com

Re: [PATCH v5 1/2] dt-bindings: Add vendor prefix for Sancloud

[Koen Kooi]

> Op 17 jul. 2018, om 09:36 heeft Alexandre Belloni <alexandre.belloni@bootlin.com> het volgende geschreven:
> 
> On 17/07/2018 09:31:15+0200, Koen Kooi wrote:
>> 
>> 
>>> Op 17 jul. 2018, om 09:20 heeft Alexandre Belloni <alexandre.belloni@bootlin.com> het volgende geschreven:
>>> 
>>> Hi Koen,
>>> 
>>> I'm not sure how you expect that to be merged but you should probably
>>> send this patch to the TI maintainers along 2/2 because probably no one
>>> in copy of this patch will apply it.
>> 
>> Is that the linux-omap list and Tony? scripts/get_maintainer.pl didn’t pick them up, which is why they are missing.
>> 
> 
> Yes, basically the same people that will apply the DT making use of this
> vendor prefix so both patches go in at the same time.

Thanks for the explanation! I resent 0001 with linux-omap and Tony explicitly adding using -cc in git-send-email.

regards,

Koen

> 
>> regards,
>> 
>> Koen
>> 
>>> 
>>> On 17/07/2018 08:24:45+0200, Koen Kooi wrote:
>>>> Add vendor prefix for Sancloud Ltd.
>>>> 
>>>> Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
>>>> Acked-by: Rob Herring <robh@kernel.org>
>>>> ---
>>>> 
>>>> v5: No changes
>>>> v4: Add Acked-by
>>>> v3: No changes
>>>> v2: No changes
>>>> v1: Initial submission
>>>> 
>>>> Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
>>>> 1 file changed, 1 insertion(+)
>>>> 
>>>> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
>>>> index 7cad066..c7aaa1f 100644
>>>> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
>>>> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
>>>> @@ -314,6 +314,7 @@ rohm	ROHM Semiconductor Co., Ltd
>>>> roofull	Shenzhen Roofull Technology Co, Ltd
>>>> samsung	Samsung Semiconductor
>>>> samtec	Samtec/Softing company
>>>> +sancloud	Sancloud Ltd
>>>> sandisk	Sandisk Corporation
>>>> sbs	Smart Battery System
>>>> schindler	Schindler
>>>> -- 
>>>> 2.0.1
>>>> 
>>> 
>>> -- 
>>> Alexandre Belloni, Bootlin (formerly Free Electrons)
>>> Embedded Linux and Kernel engineering
>>> https://bootlin.com
>> 
> 
> -- 
> Alexandre Belloni, Bootlin (formerly Free Electrons)
> Embedded Linux and Kernel engineering
> https://bootlin.com

Re: [PATCH v5 1/2] dt-bindings: Add vendor prefix for Sancloud

[Tony Lindgren]

* Koen Kooi <koen@dominion.thruhere.net> [180717 07:46]:
> 
> Thanks for the explanation! I resent 0001 with linux-omap and Tony explicitly adding using -cc in git-send-email.

Yeah thanks I'll pick up both patches.

Tony