[PATCH V6 00/23] mmc: mmci: add sdmmc variant for stm32

[PATCH V6 00/23] mmc: mmci: add sdmmc variant for stm32

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

The goal of this serie is to add support of sdmmc for stm32.
Be to able to add this new variant it is needed to do some changes in
mmci core:
-Internalize specific needs of legacy dmaengine.
-Create and setup dma_priv pointer.
-Create generic callbacks which share some features (like cookie...)
 and call specific needs.

change v6:
-move mmci_variant_init in mmci.c
-dma_setup/release: let the variants clean up themselves.

change v5:
-error management in mmci_dmae_setup and qcom_dma_setup
 mmci_dmae_setup: fail when tx & rx are not defined.
 qcom_dma_setup: faill if one of channels is not defined.
-define mmci_variant_init following CONFIG_DMA_ENGINE state.
-squash dma_setup/dma_release callback.

change v4:
-checkpatch fix bool to u8
-add use_dma variable to fallback to pio mode
-move to optional reset with dt binding note for sdmmc
-separate patch for DT doc

change v3:
-remove __dma_inprogress rename
-remove bad space at end of "st,use-ckin"

change v2:
-rename to mmci_prep/unprep_data
-rename specific dma engine structure to mmci_dmae_next/priv
-follow "_" recommandation
-remove dma prefixe of mmci_dmae_priv fields

Ludovic Barre (23):
  mmc: mmci: create common mmci_dma_setup/release
  mmc: mmci: introduce dma_priv pointer to mmci_host
  mmc: mmci: merge prepare data functions
  mmc: mmci: add prepare/unprepare_data callbacks
  mmc: mmci: add get_next_data callback
  mmc: mmci: add dma_start callback
  mmc: mmci: add dma_finalize callback
  mmc: mmci: add dma_error callback
  mmc: mmci: add validate_data callback
  mmc: mmci: add set_clk/pwrreg callbacks
  mmc: mmci: add datactrl block size variant property
  mmc: mmci: expand startbiterr to irqmask and error check
  mmc: mmci: add variant properties to define cpsm & cmdresp bits
  mmc: mmci: add variant property to define dpsm bit
  mmc: mmci: add variant property to define irq pio mask
  mmc: mmci: add variant property to write datactrl before command
  mmc: mmci: add variant property to not read datacnt
  dt-bindings: mmci: add optional reset property
  mmc: mmci: add optional reset property
  mmc: mmci: add clock divider for stm32 sdmmc
  mmc: mmci: add stm32 sdmmc registers
  dt-bindings: mmci: add stm32 sdmmc variant
  mmc: mmci: add stm32 sdmmc variant

 Documentation/devicetree/bindings/mmc/mmci.txt |  11 +
 drivers/mmc/host/Kconfig                       |  10 +
 drivers/mmc/host/Makefile                      |   1 +
 drivers/mmc/host/mmci.c                        | 628 ++++++++++++++++++-------
 drivers/mmc/host/mmci.h                        | 140 +++++-
 drivers/mmc/host/mmci_qcom_dml.c               |  17 +-
 drivers/mmc/host/mmci_stm32_sdmmc.c            | 282 +++++++++++
 7 files changed, 886 insertions(+), 203 deletions(-)
 create mode 100644 drivers/mmc/host/mmci_stm32_sdmmc.c

-- 
2.7.4

[PATCH V6 01/23] mmc: mmci: create common mmci_dma_setup/release

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch creates a common mmci_dma_setup/release which calls
dma_setup/release callbacks of mmci_host_ops and manages
common features like use_dma... If there is a fallbacks to
pio mode, dma functions must check use_dma.

error management:
-mmci_dmae_setup fail if Tx and Rx dma channels are not defined
-qcom_dma_setup fail if one of both dma channels is not defined,
 Qcom has no specific resource to release, just mmci dmae resource.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c          | 75 ++++++++++++++++++++++++++++++++--------
 drivers/mmc/host/mmci.h          |  7 +++-
 drivers/mmc/host/mmci_qcom_dml.c | 11 ++++--
 3 files changed, 75 insertions(+), 18 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index db8c085..120382b 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -45,6 +45,12 @@
 
 #define DRIVER_NAME "mmci-pl18x"
 
+#ifdef CONFIG_DMA_ENGINE
+void mmci_variant_init(struct mmci_host *host);
+#else
+static inline void mmci_variant_init(struct mmci_host *host) {}
+#endif
+
 static unsigned int fmax = 515633;
 
 static struct variant_data variant_arm = {
@@ -57,6 +63,7 @@ static struct variant_data variant_arm = {
 	.mmcimask1		= true,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_ROD,
+	.init			= mmci_variant_init,
 };
 
 static struct variant_data variant_arm_extended_fifo = {
@@ -68,6 +75,7 @@ static struct variant_data variant_arm_extended_fifo = {
 	.mmcimask1		= true,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_ROD,
+	.init			= mmci_variant_init,
 };
 
 static struct variant_data variant_arm_extended_fifo_hwfc = {
@@ -80,6 +88,7 @@ static struct variant_data variant_arm_extended_fifo_hwfc = {
 	.mmcimask1		= true,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_ROD,
+	.init			= mmci_variant_init,
 };
 
 static struct variant_data variant_u300 = {
@@ -98,6 +107,7 @@ static struct variant_data variant_u300 = {
 	.mmcimask1		= true,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_OD,
+	.init			= mmci_variant_init,
 };
 
 static struct variant_data variant_nomadik = {
@@ -117,6 +127,7 @@ static struct variant_data variant_nomadik = {
 	.mmcimask1		= true,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_OD,
+	.init			= mmci_variant_init,
 };
 
 static struct variant_data variant_ux500 = {
@@ -142,6 +153,7 @@ static struct variant_data variant_ux500 = {
 	.mmcimask1		= true,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_OD,
+	.init			= mmci_variant_init,
 };
 
 static struct variant_data variant_ux500v2 = {
@@ -169,6 +181,7 @@ static struct variant_data variant_ux500v2 = {
 	.mmcimask1		= true,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_OD,
+	.init			= mmci_variant_init,
 };
 
 static struct variant_data variant_stm32 = {
@@ -186,6 +199,7 @@ static struct variant_data variant_stm32 = {
 	.f_max			= 48000000,
 	.pwrreg_clkgate		= true,
 	.pwrreg_nopower		= true,
+	.init			= mmci_variant_init,
 };
 
 static struct variant_data variant_qcom = {
@@ -356,6 +370,25 @@ static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
 	mmci_write_clkreg(host, clk);
 }
 
+void mmci_dma_release(struct mmci_host *host)
+{
+	if (host->ops && host->ops->dma_release)
+		host->ops->dma_release(host);
+
+	host->use_dma = false;
+}
+
+void mmci_dma_setup(struct mmci_host *host)
+{
+	if (!host->ops || !host->ops->dma_setup)
+		return;
+
+	if (host->ops->dma_setup(host))
+		return;
+
+	host->use_dma = true;
+}
+
 static void
 mmci_request_end(struct mmci_host *host, struct mmc_request *mrq)
 {
@@ -414,7 +447,7 @@ static void mmci_init_sg(struct mmci_host *host, struct mmc_data *data)
  * no custom DMA interfaces are supported.
  */
 #ifdef CONFIG_DMA_ENGINE
-static void mmci_dma_setup(struct mmci_host *host)
+int mmci_dmae_setup(struct mmci_host *host)
 {
 	const char *rxname, *txname;
 
@@ -464,15 +497,19 @@ static void mmci_dma_setup(struct mmci_host *host)
 			host->mmc->max_seg_size = max_seg_size;
 	}
 
-	if (host->ops && host->ops->dma_setup)
-		host->ops->dma_setup(host);
+	if (!host->dma_tx_channel && !host->dma_rx_channel) {
+		mmci_dmae_release(host);
+		return -EINVAL;
+	}
+
+	return 0;
 }
 
 /*
  * This is used in or so inline it
  * so it can be discarded.
  */
-static inline void mmci_dma_release(struct mmci_host *host)
+void mmci_dmae_release(struct mmci_host *host)
 {
 	if (host->dma_rx_channel)
 		dma_release_channel(host->dma_rx_channel);
@@ -496,7 +533,7 @@ static void mmci_dma_unmap(struct mmci_host *host, struct mmc_data *data)
 
 static void mmci_dma_data_error(struct mmci_host *host)
 {
-	if (!dma_inprogress(host))
+	if (!host->use_dma || !dma_inprogress(host))
 		return;
 
 	dev_err(mmc_dev(host->mmc), "error during DMA transfer!\n");
@@ -514,7 +551,7 @@ static void mmci_dma_finalize(struct mmci_host *host, struct mmc_data *data)
 	u32 status;
 	int i;
 
-	if (!dma_inprogress(host))
+	if (!host->use_dma || !dma_inprogress(host))
 		return;
 
 	/* Wait up to 1ms for the DMA to complete */
@@ -640,6 +677,9 @@ static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
 	int ret;
 	struct mmc_data *data = host->data;
 
+	if (!host->use_dma)
+		return -EINVAL;
+
 	ret = mmci_dma_prep_data(host, host->data);
 	if (ret)
 		return ret;
@@ -674,6 +714,9 @@ static void mmci_get_next_data(struct mmci_host *host, struct mmc_data *data)
 {
 	struct mmci_host_next *next = &host->next_data;
 
+	if (!host->use_dma)
+		return;
+
 	WARN_ON(data->host_cookie && data->host_cookie != next->cookie);
 	WARN_ON(!data->host_cookie && (next->dma_desc || next->dma_chan));
 
@@ -689,7 +732,7 @@ static void mmci_pre_request(struct mmc_host *mmc, struct mmc_request *mrq)
 	struct mmc_data *data = mrq->data;
 	struct mmci_host_next *nd = &host->next_data;
 
-	if (!data)
+	if (!host->use_dma || !data)
 		return;
 
 	BUG_ON(data->host_cookie);
@@ -707,7 +750,7 @@ static void mmci_post_request(struct mmc_host *mmc, struct mmc_request *mrq,
 	struct mmci_host *host = mmc_priv(mmc);
 	struct mmc_data *data = mrq->data;
 
-	if (!data || !data->host_cookie)
+	if (!host->use_dma || !data || !data->host_cookie)
 		return;
 
 	mmci_dma_unmap(host, data);
@@ -735,18 +778,20 @@ static void mmci_post_request(struct mmc_host *mmc, struct mmc_request *mrq,
 	}
 }
 
+static struct mmci_host_ops mmci_variant_ops = {
+	.dma_setup = mmci_dmae_setup,
+	.dma_release = mmci_dmae_release,
+};
+
+void mmci_variant_init(struct mmci_host *host)
+{
+	host->ops = &mmci_variant_ops;
+}
 #else
 /* Blank functions if the DMA engine is not available */
 static void mmci_get_next_data(struct mmci_host *host, struct mmc_data *data)
 {
 }
-static inline void mmci_dma_setup(struct mmci_host *host)
-{
-}
-
-static inline void mmci_dma_release(struct mmci_host *host)
-{
-}
 
 static inline void mmci_dma_finalize(struct mmci_host *host,
 				     struct mmc_data *data)
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 01e6c6b..34bb5e6 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -273,7 +273,8 @@ struct variant_data {
 
 /* mmci variant callbacks */
 struct mmci_host_ops {
-	void (*dma_setup)(struct mmci_host *host);
+	int (*dma_setup)(struct mmci_host *host);
+	void (*dma_release)(struct mmci_host *host);
 };
 
 struct mmci_host_next {
@@ -323,6 +324,7 @@ struct mmci_host {
 	unsigned int		size;
 	int (*get_rx_fifocnt)(struct mmci_host *h, u32 status, int remain);
 
+	u8			use_dma:1;
 #ifdef CONFIG_DMA_ENGINE
 	/* DMA stuff */
 	struct dma_chan		*dma_current;
@@ -336,3 +338,6 @@ struct mmci_host {
 #endif
 };
 
+int mmci_dmae_setup(struct mmci_host *host);
+void mmci_dmae_release(struct mmci_host *host);
+
diff --git a/drivers/mmc/host/mmci_qcom_dml.c b/drivers/mmc/host/mmci_qcom_dml.c
index be3fab5..92b03a3 100644
--- a/drivers/mmc/host/mmci_qcom_dml.c
+++ b/drivers/mmc/host/mmci_qcom_dml.c
@@ -119,19 +119,23 @@ static int of_get_dml_pipe_index(struct device_node *np, const char *name)
 }
 
 /* Initialize the dml hardware connected to SD Card controller */
-static void qcom_dma_setup(struct mmci_host *host)
+static int qcom_dma_setup(struct mmci_host *host)
 {
 	u32 config;
 	void __iomem *base;
 	int consumer_id, producer_id;
 	struct device_node *np = host->mmc->parent->of_node;
 
+	if (mmci_dmae_setup(host))
+		return -EINVAL;
+
 	consumer_id = of_get_dml_pipe_index(np, "tx");
 	producer_id = of_get_dml_pipe_index(np, "rx");
 
 	if (producer_id < 0 || consumer_id < 0) {
 		host->variant->qcom_dml = false;
-		return;
+		mmci_dmae_release(host);
+		return -EINVAL;
 	}
 
 	base = host->base + DML_OFFSET;
@@ -175,10 +179,13 @@ static void qcom_dma_setup(struct mmci_host *host)
 
 	/* Make sure dml initialization is finished */
 	mb();
+
+	return 0;
 }
 
 static struct mmci_host_ops qcom_variant_ops = {
 	.dma_setup = qcom_dma_setup,
+	.dma_release = mmci_dmae_release,
 };
 
 void qcom_variant_init(struct mmci_host *host)
-- 
2.7.4

[PATCH V6 02/23] mmc: mmci: introduce dma_priv pointer to mmci_host

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

-Introduces dma_priv pointer to define specific
needs for each dma engine. This patch is needed to prepare
sdmmc variant with internal dma which not use dmaengine API.
-Moves next cookie to mmci host structure to share same cookie
management between all variants.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 144 ++++++++++++++++++++++++++++++------------------
 drivers/mmc/host/mmci.h |  19 ++-----
 2 files changed, 94 insertions(+), 69 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 120382b..922a47b 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -386,6 +386,9 @@ void mmci_dma_setup(struct mmci_host *host)
 	if (host->ops->dma_setup(host))
 		return;
 
+	/* initialize pre request cookie */
+	host->next_cookie = 1;
+
 	host->use_dma = true;
 }
 
@@ -447,31 +450,50 @@ static void mmci_init_sg(struct mmci_host *host, struct mmc_data *data)
  * no custom DMA interfaces are supported.
  */
 #ifdef CONFIG_DMA_ENGINE
+struct mmci_dmae_next {
+	struct dma_async_tx_descriptor *desc;
+	struct dma_chan	*chan;
+};
+
+struct mmci_dmae_priv {
+	struct dma_chan	*cur;
+	struct dma_chan	*rx_channel;
+	struct dma_chan	*tx_channel;
+	struct dma_async_tx_descriptor	*desc_current;
+	struct mmci_dmae_next next_data;
+};
+
 int mmci_dmae_setup(struct mmci_host *host)
 {
 	const char *rxname, *txname;
+	struct mmci_dmae_priv *dmae;
 
-	host->dma_rx_channel = dma_request_slave_channel(mmc_dev(host->mmc), "rx");
-	host->dma_tx_channel = dma_request_slave_channel(mmc_dev(host->mmc), "tx");
+	dmae = devm_kzalloc(mmc_dev(host->mmc), sizeof(*dmae), GFP_KERNEL);
+	if (!dmae)
+		return -ENOMEM;
 
-	/* initialize pre request cookie */
-	host->next_data.cookie = 1;
+	host->dma_priv = dmae;
+
+	dmae->rx_channel = dma_request_slave_channel(mmc_dev(host->mmc),
+						     "rx");
+	dmae->tx_channel = dma_request_slave_channel(mmc_dev(host->mmc),
+						     "tx");
 
 	/*
 	 * If only an RX channel is specified, the driver will
 	 * attempt to use it bidirectionally, however if it is
 	 * is specified but cannot be located, DMA will be disabled.
 	 */
-	if (host->dma_rx_channel && !host->dma_tx_channel)
-		host->dma_tx_channel = host->dma_rx_channel;
+	if (dmae->rx_channel && !dmae->tx_channel)
+		dmae->tx_channel = dmae->rx_channel;
 
-	if (host->dma_rx_channel)
-		rxname = dma_chan_name(host->dma_rx_channel);
+	if (dmae->rx_channel)
+		rxname = dma_chan_name(dmae->rx_channel);
 	else
 		rxname = "none";
 
-	if (host->dma_tx_channel)
-		txname = dma_chan_name(host->dma_tx_channel);
+	if (dmae->tx_channel)
+		txname = dma_chan_name(dmae->tx_channel);
 	else
 		txname = "none";
 
@@ -482,22 +504,22 @@ int mmci_dmae_setup(struct mmci_host *host)
 	 * Limit the maximum segment size in any SG entry according to
 	 * the parameters of the DMA engine device.
 	 */
-	if (host->dma_tx_channel) {
-		struct device *dev = host->dma_tx_channel->device->dev;
+	if (dmae->tx_channel) {
+		struct device *dev = dmae->tx_channel->device->dev;
 		unsigned int max_seg_size = dma_get_max_seg_size(dev);
 
 		if (max_seg_size < host->mmc->max_seg_size)
 			host->mmc->max_seg_size = max_seg_size;
 	}
-	if (host->dma_rx_channel) {
-		struct device *dev = host->dma_rx_channel->device->dev;
+	if (dmae->rx_channel) {
+		struct device *dev = dmae->rx_channel->device->dev;
 		unsigned int max_seg_size = dma_get_max_seg_size(dev);
 
 		if (max_seg_size < host->mmc->max_seg_size)
 			host->mmc->max_seg_size = max_seg_size;
 	}
 
-	if (!host->dma_tx_channel && !host->dma_rx_channel) {
+	if (!dmae->tx_channel || !dmae->rx_channel) {
 		mmci_dmae_release(host);
 		return -EINVAL;
 	}
@@ -511,21 +533,24 @@ int mmci_dmae_setup(struct mmci_host *host)
  */
 void mmci_dmae_release(struct mmci_host *host)
 {
-	if (host->dma_rx_channel)
-		dma_release_channel(host->dma_rx_channel);
-	if (host->dma_tx_channel)
-		dma_release_channel(host->dma_tx_channel);
-	host->dma_rx_channel = host->dma_tx_channel = NULL;
+	struct mmci_dmae_priv *dmae = host->dma_priv;
+
+	if (dmae->rx_channel)
+		dma_release_channel(dmae->rx_channel);
+	if (dmae->tx_channel)
+		dma_release_channel(dmae->tx_channel);
+	dmae->rx_channel = dmae->tx_channel = NULL;
 }
 
 static void mmci_dma_unmap(struct mmci_host *host, struct mmc_data *data)
 {
+	struct mmci_dmae_priv *dmae = host->dma_priv;
 	struct dma_chan *chan;
 
 	if (data->flags & MMC_DATA_READ)
-		chan = host->dma_rx_channel;
+		chan = dmae->rx_channel;
 	else
-		chan = host->dma_tx_channel;
+		chan = dmae->tx_channel;
 
 	dma_unmap_sg(chan->device->dev, data->sg, data->sg_len,
 		     mmc_get_dma_dir(data));
@@ -533,14 +558,16 @@ static void mmci_dma_unmap(struct mmci_host *host, struct mmc_data *data)
 
 static void mmci_dma_data_error(struct mmci_host *host)
 {
+	struct mmci_dmae_priv *dmae = host->dma_priv;
+
 	if (!host->use_dma || !dma_inprogress(host))
 		return;
 
 	dev_err(mmc_dev(host->mmc), "error during DMA transfer!\n");
-	dmaengine_terminate_all(host->dma_current);
+	dmaengine_terminate_all(dmae->cur);
 	host->dma_in_progress = false;
-	host->dma_current = NULL;
-	host->dma_desc_current = NULL;
+	dmae->cur = NULL;
+	dmae->desc_current = NULL;
 	host->data->host_cookie = 0;
 
 	mmci_dma_unmap(host, host->data);
@@ -548,6 +575,7 @@ static void mmci_dma_data_error(struct mmci_host *host)
 
 static void mmci_dma_finalize(struct mmci_host *host, struct mmc_data *data)
 {
+	struct mmci_dmae_priv *dmae = host->dma_priv;
 	u32 status;
 	int i;
 
@@ -586,8 +614,8 @@ static void mmci_dma_finalize(struct mmci_host *host, struct mmc_data *data)
 	}
 
 	host->dma_in_progress = false;
-	host->dma_current = NULL;
-	host->dma_desc_current = NULL;
+	dmae->cur = NULL;
+	dmae->desc_current = NULL;
 }
 
 /* prepares DMA channel and DMA descriptor, returns non-zero on failure */
@@ -595,6 +623,7 @@ static int __mmci_dma_prep_data(struct mmci_host *host, struct mmc_data *data,
 				struct dma_chan **dma_chan,
 				struct dma_async_tx_descriptor **dma_desc)
 {
+	struct mmci_dmae_priv *dmae = host->dma_priv;
 	struct variant_data *variant = host->variant;
 	struct dma_slave_config conf = {
 		.src_addr = host->phybase + MMCIFIFO,
@@ -613,10 +642,10 @@ static int __mmci_dma_prep_data(struct mmci_host *host, struct mmc_data *data,
 
 	if (data->flags & MMC_DATA_READ) {
 		conf.direction = DMA_DEV_TO_MEM;
-		chan = host->dma_rx_channel;
+		chan = dmae->rx_channel;
 	} else {
 		conf.direction = DMA_MEM_TO_DEV;
-		chan = host->dma_tx_channel;
+		chan = dmae->tx_channel;
 	}
 
 	/* If there's no DMA channel, fall back to PIO */
@@ -656,25 +685,30 @@ static int __mmci_dma_prep_data(struct mmci_host *host, struct mmc_data *data,
 static inline int mmci_dma_prep_data(struct mmci_host *host,
 				     struct mmc_data *data)
 {
+	struct mmci_dmae_priv *dmae = host->dma_priv;
+
 	/* Check if next job is already prepared. */
-	if (host->dma_current && host->dma_desc_current)
+	if (dmae->cur && dmae->desc_current)
 		return 0;
 
 	/* No job were prepared thus do it now. */
-	return __mmci_dma_prep_data(host, data, &host->dma_current,
-				    &host->dma_desc_current);
+	return __mmci_dma_prep_data(host, data, &dmae->cur,
+				    &dmae->desc_current);
 }
 
 static inline int mmci_dma_prep_next(struct mmci_host *host,
 				     struct mmc_data *data)
 {
-	struct mmci_host_next *nd = &host->next_data;
-	return __mmci_dma_prep_data(host, data, &nd->dma_chan, &nd->dma_desc);
+	struct mmci_dmae_priv *dmae = host->dma_priv;
+	struct mmci_dmae_next *nd = &dmae->next_data;
+
+	return __mmci_dma_prep_data(host, data, &nd->chan, &nd->desc);
 }
 
 static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
 {
 	int ret;
+	struct mmci_dmae_priv *dmae = host->dma_priv;
 	struct mmc_data *data = host->data;
 
 	if (!host->use_dma)
@@ -689,8 +723,8 @@ static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
 		 "Submit MMCI DMA job, sglen %d blksz %04x blks %04x flags %08x\n",
 		 data->sg_len, data->blksz, data->blocks, data->flags);
 	host->dma_in_progress = true;
-	dmaengine_submit(host->dma_desc_current);
-	dma_async_issue_pending(host->dma_current);
+	dmaengine_submit(dmae->desc_current);
+	dma_async_issue_pending(dmae->cur);
 
 	if (host->variant->qcom_dml)
 		dml_start_xfer(host, data);
@@ -712,25 +746,25 @@ static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
 
 static void mmci_get_next_data(struct mmci_host *host, struct mmc_data *data)
 {
-	struct mmci_host_next *next = &host->next_data;
+	struct mmci_dmae_priv *dmae = host->dma_priv;
+	struct mmci_dmae_next *next = &dmae->next_data;
 
 	if (!host->use_dma)
 		return;
 
-	WARN_ON(data->host_cookie && data->host_cookie != next->cookie);
-	WARN_ON(!data->host_cookie && (next->dma_desc || next->dma_chan));
+	WARN_ON(data->host_cookie && data->host_cookie != host->next_cookie);
+	WARN_ON(!data->host_cookie && (next->desc || next->chan));
 
-	host->dma_desc_current = next->dma_desc;
-	host->dma_current = next->dma_chan;
-	next->dma_desc = NULL;
-	next->dma_chan = NULL;
+	dmae->desc_current = next->desc;
+	dmae->cur = next->chan;
+	next->desc = NULL;
+	next->chan = NULL;
 }
 
 static void mmci_pre_request(struct mmc_host *mmc, struct mmc_request *mrq)
 {
 	struct mmci_host *host = mmc_priv(mmc);
 	struct mmc_data *data = mrq->data;
-	struct mmci_host_next *nd = &host->next_data;
 
 	if (!host->use_dma || !data)
 		return;
@@ -741,13 +775,15 @@ static void mmci_pre_request(struct mmc_host *mmc, struct mmc_request *mrq)
 		return;
 
 	if (!mmci_dma_prep_next(host, data))
-		data->host_cookie = ++nd->cookie < 0 ? 1 : nd->cookie;
+		data->host_cookie = ++host->next_cookie < 0 ?
+			1 : host->next_cookie;
 }
 
 static void mmci_post_request(struct mmc_host *mmc, struct mmc_request *mrq,
 			      int err)
 {
 	struct mmci_host *host = mmc_priv(mmc);
+	struct mmci_dmae_priv *dmae = host->dma_priv;
 	struct mmc_data *data = mrq->data;
 
 	if (!host->use_dma || !data || !data->host_cookie)
@@ -756,24 +792,24 @@ static void mmci_post_request(struct mmc_host *mmc, struct mmc_request *mrq,
 	mmci_dma_unmap(host, data);
 
 	if (err) {
-		struct mmci_host_next *next = &host->next_data;
+		struct mmci_dmae_next *next = &dmae->next_data;
 		struct dma_chan *chan;
 		if (data->flags & MMC_DATA_READ)
-			chan = host->dma_rx_channel;
+			chan = dmae->rx_channel;
 		else
-			chan = host->dma_tx_channel;
+			chan = dmae->tx_channel;
 		dmaengine_terminate_all(chan);
 
-		if (host->dma_desc_current == next->dma_desc)
-			host->dma_desc_current = NULL;
+		if (dmae->desc_current == next->desc)
+			dmae->desc_current = NULL;
 
-		if (host->dma_current == next->dma_chan) {
+		if (dmae->cur == next->chan) {
 			host->dma_in_progress = false;
-			host->dma_current = NULL;
+			dmae->cur = NULL;
 		}
 
-		next->dma_desc = NULL;
-		next->dma_chan = NULL;
+		next->desc = NULL;
+		next->chan = NULL;
 		data->host_cookie = 0;
 	}
 }
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 34bb5e6..1d5ba4e 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -277,12 +277,6 @@ struct mmci_host_ops {
 	void (*dma_release)(struct mmci_host *host);
 };
 
-struct mmci_host_next {
-	struct dma_async_tx_descriptor	*dma_desc;
-	struct dma_chan			*dma_chan;
-	s32				cookie;
-};
-
 struct mmci_host {
 	phys_addr_t		phybase;
 	void __iomem		*base;
@@ -325,19 +319,14 @@ struct mmci_host {
 	int (*get_rx_fifocnt)(struct mmci_host *h, u32 status, int remain);
 
 	u8			use_dma:1;
-#ifdef CONFIG_DMA_ENGINE
-	/* DMA stuff */
-	struct dma_chan		*dma_current;
-	struct dma_chan		*dma_rx_channel;
-	struct dma_chan		*dma_tx_channel;
-	struct dma_async_tx_descriptor	*dma_desc_current;
-	struct mmci_host_next	next_data;
 	u8			dma_in_progress:1;
+	void			*dma_priv;
 
-#define dma_inprogress(host)	((host)->dma_in_progress)
-#endif
+	s32			next_cookie;
 };
 
+#define dma_inprogress(host)	((host)->dma_in_progress)
+
 int mmci_dmae_setup(struct mmci_host *host);
 void mmci_dmae_release(struct mmci_host *host);
 
-- 
2.7.4

[PATCH V6 03/23] mmc: mmci: merge prepare data functions

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch merges the prepare data functions.
This allows to define a single access to prepare data service.
This prepares integration for mmci host ops.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 19 +++++++------------
 1 file changed, 7 insertions(+), 12 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 922a47b..f862a1b 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -683,10 +683,14 @@ static int __mmci_dma_prep_data(struct mmci_host *host, struct mmc_data *data,
 }
 
 static inline int mmci_dma_prep_data(struct mmci_host *host,
-				     struct mmc_data *data)
+				     struct mmc_data *data,
+				     bool next)
 {
 	struct mmci_dmae_priv *dmae = host->dma_priv;
+	struct mmci_dmae_next *nd = &dmae->next_data;
 
+	if (next)
+		return __mmci_dma_prep_data(host, data, &nd->chan, &nd->desc);
 	/* Check if next job is already prepared. */
 	if (dmae->cur && dmae->desc_current)
 		return 0;
@@ -696,15 +700,6 @@ static inline int mmci_dma_prep_data(struct mmci_host *host,
 				    &dmae->desc_current);
 }
 
-static inline int mmci_dma_prep_next(struct mmci_host *host,
-				     struct mmc_data *data)
-{
-	struct mmci_dmae_priv *dmae = host->dma_priv;
-	struct mmci_dmae_next *nd = &dmae->next_data;
-
-	return __mmci_dma_prep_data(host, data, &nd->chan, &nd->desc);
-}
-
 static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
 {
 	int ret;
@@ -714,7 +709,7 @@ static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
 	if (!host->use_dma)
 		return -EINVAL;
 
-	ret = mmci_dma_prep_data(host, host->data);
+	ret = mmci_dma_prep_data(host, host->data, false);
 	if (ret)
 		return ret;
 
@@ -774,7 +769,7 @@ static void mmci_pre_request(struct mmc_host *mmc, struct mmc_request *mrq)
 	if (mmci_validate_data(host, data))
 		return;
 
-	if (!mmci_dma_prep_next(host, data))
+	if (!mmci_dma_prep_data(host, data, true))
 		data->host_cookie = ++host->next_cookie < 0 ?
 			1 : host->next_cookie;
 }
-- 
2.7.4

[PATCH V6 04/23] mmc: mmci: add prepare/unprepare_data callbacks

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds prepare/unprepare callbacks to mmci_host_ops.
Like this mmci_pre/post_request can be generic, mmci_prepare_data
and mmci_unprepare_data provide common next_cookie management.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c          | 101 ++++++++++++++++++++++++++-------------
 drivers/mmc/host/mmci.h          |   8 ++++
 drivers/mmc/host/mmci_qcom_dml.c |   2 +
 3 files changed, 78 insertions(+), 33 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index f862a1b..4db2b3f 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -392,6 +392,31 @@ void mmci_dma_setup(struct mmci_host *host)
 	host->use_dma = true;
 }
 
+int mmci_prep_data(struct mmci_host *host, struct mmc_data *data, bool next)
+{
+	int err;
+
+	if (!host->ops || !host->ops->prep_data)
+		return 0;
+
+	err = host->ops->prep_data(host, data, next);
+
+	if (next && !err)
+		data->host_cookie = ++host->next_cookie < 0 ?
+			1 : host->next_cookie;
+
+	return err;
+}
+
+void mmci_unprep_data(struct mmci_host *host, struct mmc_data *data,
+		      int err)
+{
+	if (host->ops && host->ops->unprep_data)
+		host->ops->unprep_data(host, data, err);
+
+	data->host_cookie = 0;
+}
+
 static void
 mmci_request_end(struct mmci_host *host, struct mmc_request *mrq)
 {
@@ -619,7 +644,7 @@ static void mmci_dma_finalize(struct mmci_host *host, struct mmc_data *data)
 }
 
 /* prepares DMA channel and DMA descriptor, returns non-zero on failure */
-static int __mmci_dma_prep_data(struct mmci_host *host, struct mmc_data *data,
+static int _mmci_dmae_prep_data(struct mmci_host *host, struct mmc_data *data,
 				struct dma_chan **dma_chan,
 				struct dma_async_tx_descriptor **dma_desc)
 {
@@ -682,21 +707,24 @@ static int __mmci_dma_prep_data(struct mmci_host *host, struct mmc_data *data,
 	return -ENOMEM;
 }
 
-static inline int mmci_dma_prep_data(struct mmci_host *host,
-				     struct mmc_data *data,
-				     bool next)
+int mmci_dmae_prep_data(struct mmci_host *host,
+			struct mmc_data *data,
+			bool next)
 {
 	struct mmci_dmae_priv *dmae = host->dma_priv;
 	struct mmci_dmae_next *nd = &dmae->next_data;
 
+	if (!host->use_dma)
+		return -EINVAL;
+
 	if (next)
-		return __mmci_dma_prep_data(host, data, &nd->chan, &nd->desc);
+		return _mmci_dmae_prep_data(host, data, &nd->chan, &nd->desc);
 	/* Check if next job is already prepared. */
 	if (dmae->cur && dmae->desc_current)
 		return 0;
 
 	/* No job were prepared thus do it now. */
-	return __mmci_dma_prep_data(host, data, &dmae->cur,
+	return _mmci_dmae_prep_data(host, data, &dmae->cur,
 				    &dmae->desc_current);
 }
 
@@ -709,7 +737,7 @@ static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
 	if (!host->use_dma)
 		return -EINVAL;
 
-	ret = mmci_dma_prep_data(host, host->data, false);
+	ret = mmci_dmae_prep_data(host, host->data, false);
 	if (ret)
 		return ret;
 
@@ -756,32 +784,13 @@ static void mmci_get_next_data(struct mmci_host *host, struct mmc_data *data)
 	next->chan = NULL;
 }
 
-static void mmci_pre_request(struct mmc_host *mmc, struct mmc_request *mrq)
-{
-	struct mmci_host *host = mmc_priv(mmc);
-	struct mmc_data *data = mrq->data;
-
-	if (!host->use_dma || !data)
-		return;
-
-	BUG_ON(data->host_cookie);
-
-	if (mmci_validate_data(host, data))
-		return;
-
-	if (!mmci_dma_prep_data(host, data, true))
-		data->host_cookie = ++host->next_cookie < 0 ?
-			1 : host->next_cookie;
-}
+void mmci_dmae_unprep_data(struct mmci_host *host,
+			   struct mmc_data *data, int err)
 
-static void mmci_post_request(struct mmc_host *mmc, struct mmc_request *mrq,
-			      int err)
 {
-	struct mmci_host *host = mmc_priv(mmc);
 	struct mmci_dmae_priv *dmae = host->dma_priv;
-	struct mmc_data *data = mrq->data;
 
-	if (!host->use_dma || !data || !data->host_cookie)
+	if (!host->use_dma)
 		return;
 
 	mmci_dma_unmap(host, data);
@@ -805,11 +814,12 @@ static void mmci_post_request(struct mmc_host *mmc, struct mmc_request *mrq,
 
 		next->desc = NULL;
 		next->chan = NULL;
-		data->host_cookie = 0;
 	}
 }
 
 static struct mmci_host_ops mmci_variant_ops = {
+	.prep_data = mmci_dmae_prep_data,
+	.unprep_data = mmci_dmae_unprep_data,
 	.dma_setup = mmci_dmae_setup,
 	.dma_release = mmci_dmae_release,
 };
@@ -838,11 +848,36 @@ static inline int mmci_dma_start_data(struct mmci_host *host, unsigned int datac
 	return -ENOSYS;
 }
 
-#define mmci_pre_request NULL
-#define mmci_post_request NULL
-
 #endif
 
+static void mmci_pre_request(struct mmc_host *mmc, struct mmc_request *mrq)
+{
+	struct mmci_host *host = mmc_priv(mmc);
+	struct mmc_data *data = mrq->data;
+
+	if (!data)
+		return;
+
+	WARN_ON(data->host_cookie);
+
+	if (mmci_validate_data(host, data))
+		return;
+
+	mmci_prep_data(host, data, true);
+}
+
+static void mmci_post_request(struct mmc_host *mmc, struct mmc_request *mrq,
+			      int err)
+{
+	struct mmci_host *host = mmc_priv(mmc);
+	struct mmc_data *data = mrq->data;
+
+	if (!data || !data->host_cookie)
+		return;
+
+	mmci_unprep_data(host, data, err);
+}
+
 static void mmci_start_data(struct mmci_host *host, struct mmc_data *data)
 {
 	struct variant_data *variant = host->variant;
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 1d5ba4e..decb1c7 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -273,6 +273,10 @@ struct variant_data {
 
 /* mmci variant callbacks */
 struct mmci_host_ops {
+	int (*prep_data)(struct mmci_host *host, struct mmc_data *data,
+			 bool next);
+	void (*unprep_data)(struct mmci_host *host, struct mmc_data *data,
+			    int err);
 	int (*dma_setup)(struct mmci_host *host);
 	void (*dma_release)(struct mmci_host *host);
 };
@@ -327,6 +331,10 @@ struct mmci_host {
 
 #define dma_inprogress(host)	((host)->dma_in_progress)
 
+int mmci_dmae_prep_data(struct mmci_host *host, struct mmc_data *data,
+			bool next);
+void mmci_dmae_unprep_data(struct mmci_host *host, struct mmc_data *data,
+			   int err);
 int mmci_dmae_setup(struct mmci_host *host);
 void mmci_dmae_release(struct mmci_host *host);
 
diff --git a/drivers/mmc/host/mmci_qcom_dml.c b/drivers/mmc/host/mmci_qcom_dml.c
index 92b03a3..156e30b 100644
--- a/drivers/mmc/host/mmci_qcom_dml.c
+++ b/drivers/mmc/host/mmci_qcom_dml.c
@@ -184,6 +184,8 @@ static int qcom_dma_setup(struct mmci_host *host)
 }
 
 static struct mmci_host_ops qcom_variant_ops = {
+	.prep_data = mmci_dmae_prep_data,
+	.unprep_data = mmci_dmae_unprep_data,
 	.dma_setup = qcom_dma_setup,
 	.dma_release = mmci_dmae_release,
 };
-- 
2.7.4

[PATCH V6 05/23] mmc: mmci: add get_next_data callback

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds get_next_data callback to mmci_host_ops.
Generic mmci_get_next_data factorizes next_cookie check and
the host ops call.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c          | 16 ++++++++++------
 drivers/mmc/host/mmci.h          |  2 ++
 drivers/mmc/host/mmci_qcom_dml.c |  1 +
 3 files changed, 13 insertions(+), 6 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 4db2b3f..8d483dd 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -417,6 +417,14 @@ void mmci_unprep_data(struct mmci_host *host, struct mmc_data *data,
 	data->host_cookie = 0;
 }
 
+void mmci_get_next_data(struct mmci_host *host, struct mmc_data *data)
+{
+	WARN_ON(data->host_cookie && data->host_cookie != host->next_cookie);
+
+	if (host->ops && host->ops->get_next_data)
+		host->ops->get_next_data(host, data);
+}
+
 static void
 mmci_request_end(struct mmci_host *host, struct mmc_request *mrq)
 {
@@ -767,7 +775,7 @@ static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
 	return 0;
 }
 
-static void mmci_get_next_data(struct mmci_host *host, struct mmc_data *data)
+void mmci_dmae_get_next_data(struct mmci_host *host, struct mmc_data *data)
 {
 	struct mmci_dmae_priv *dmae = host->dma_priv;
 	struct mmci_dmae_next *next = &dmae->next_data;
@@ -775,7 +783,6 @@ static void mmci_get_next_data(struct mmci_host *host, struct mmc_data *data)
 	if (!host->use_dma)
 		return;
 
-	WARN_ON(data->host_cookie && data->host_cookie != host->next_cookie);
 	WARN_ON(!data->host_cookie && (next->desc || next->chan));
 
 	dmae->desc_current = next->desc;
@@ -820,6 +827,7 @@ void mmci_dmae_unprep_data(struct mmci_host *host,
 static struct mmci_host_ops mmci_variant_ops = {
 	.prep_data = mmci_dmae_prep_data,
 	.unprep_data = mmci_dmae_unprep_data,
+	.get_next_data = mmci_dmae_get_next_data,
 	.dma_setup = mmci_dmae_setup,
 	.dma_release = mmci_dmae_release,
 };
@@ -830,10 +838,6 @@ void mmci_variant_init(struct mmci_host *host)
 }
 #else
 /* Blank functions if the DMA engine is not available */
-static void mmci_get_next_data(struct mmci_host *host, struct mmc_data *data)
-{
-}
-
 static inline void mmci_dma_finalize(struct mmci_host *host,
 				     struct mmc_data *data)
 {
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index decb1c7..a6a85aa 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -277,6 +277,7 @@ struct mmci_host_ops {
 			 bool next);
 	void (*unprep_data)(struct mmci_host *host, struct mmc_data *data,
 			    int err);
+	void (*get_next_data)(struct mmci_host *host, struct mmc_data *data);
 	int (*dma_setup)(struct mmci_host *host);
 	void (*dma_release)(struct mmci_host *host);
 };
@@ -335,6 +336,7 @@ int mmci_dmae_prep_data(struct mmci_host *host, struct mmc_data *data,
 			bool next);
 void mmci_dmae_unprep_data(struct mmci_host *host, struct mmc_data *data,
 			   int err);
+void mmci_dmae_get_next_data(struct mmci_host *host, struct mmc_data *data);
 int mmci_dmae_setup(struct mmci_host *host);
 void mmci_dmae_release(struct mmci_host *host);
 
diff --git a/drivers/mmc/host/mmci_qcom_dml.c b/drivers/mmc/host/mmci_qcom_dml.c
index 156e30b..da4c43a 100644
--- a/drivers/mmc/host/mmci_qcom_dml.c
+++ b/drivers/mmc/host/mmci_qcom_dml.c
@@ -186,6 +186,7 @@ static int qcom_dma_setup(struct mmci_host *host)
 static struct mmci_host_ops qcom_variant_ops = {
 	.prep_data = mmci_dmae_prep_data,
 	.unprep_data = mmci_dmae_unprep_data,
+	.get_next_data = mmci_dmae_get_next_data,
 	.dma_setup = qcom_dma_setup,
 	.dma_release = mmci_dmae_release,
 };
-- 
2.7.4

[PATCH V6 06/23] mmc: mmci: add dma_start callback

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds dma_start callback to mmci_host_ops.
Create a generic mmci_dma_start function which regroup
common action between variant.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c          | 69 +++++++++++++++++++++++-----------------
 drivers/mmc/host/mmci.h          |  2 ++
 drivers/mmc/host/mmci_qcom_dml.c |  1 +
 3 files changed, 42 insertions(+), 30 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 8d483dd..72584f4 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -425,6 +425,41 @@ void mmci_get_next_data(struct mmci_host *host, struct mmc_data *data)
 		host->ops->get_next_data(host, data);
 }
 
+int mmci_dma_start(struct mmci_host *host, unsigned int datactrl)
+{
+	struct mmc_data *data = host->data;
+	int ret;
+
+	if (!host->use_dma)
+		return -EINVAL;
+
+	ret = mmci_prep_data(host, data, false);
+	if (ret)
+		return ret;
+
+	if (!host->ops || !host->ops->dma_start)
+		return -EINVAL;
+
+	/* Okay, go for it. */
+	dev_vdbg(mmc_dev(host->mmc),
+		 "Submit MMCI DMA job, sglen %d blksz %04x blks %04x flags %08x\n",
+		 data->sg_len, data->blksz, data->blocks, data->flags);
+
+	host->ops->dma_start(host, &datactrl);
+
+	/* Trigger the DMA transfer */
+	mmci_write_datactrlreg(host, datactrl);
+
+	/*
+	 * Let the MMCI say when the data is ended and it's time
+	 * to fire next DMA request. When that happens, MMCI will
+	 * call mmci_data_end()
+	 */
+	writel(readl(host->base + MMCIMASK0) | MCI_DATAENDMASK,
+	       host->base + MMCIMASK0);
+	return 0;
+}
+
 static void
 mmci_request_end(struct mmci_host *host, struct mmc_request *mrq)
 {
@@ -736,23 +771,11 @@ int mmci_dmae_prep_data(struct mmci_host *host,
 				    &dmae->desc_current);
 }
 
-static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
+int mmci_dmae_start(struct mmci_host *host, unsigned int *datactrl)
 {
-	int ret;
 	struct mmci_dmae_priv *dmae = host->dma_priv;
 	struct mmc_data *data = host->data;
 
-	if (!host->use_dma)
-		return -EINVAL;
-
-	ret = mmci_dmae_prep_data(host, host->data, false);
-	if (ret)
-		return ret;
-
-	/* Okay, go for it. */
-	dev_vdbg(mmc_dev(host->mmc),
-		 "Submit MMCI DMA job, sglen %d blksz %04x blks %04x flags %08x\n",
-		 data->sg_len, data->blksz, data->blocks, data->flags);
 	host->dma_in_progress = true;
 	dmaengine_submit(dmae->desc_current);
 	dma_async_issue_pending(dmae->cur);
@@ -760,18 +783,8 @@ static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
 	if (host->variant->qcom_dml)
 		dml_start_xfer(host, data);
 
-	datactrl |= MCI_DPSM_DMAENABLE;
+	*datactrl |= MCI_DPSM_DMAENABLE;
 
-	/* Trigger the DMA transfer */
-	mmci_write_datactrlreg(host, datactrl);
-
-	/*
-	 * Let the MMCI say when the data is ended and it's time
-	 * to fire next DMA request. When that happens, MMCI will
-	 * call mmci_data_end()
-	 */
-	writel(readl(host->base + MMCIMASK0) | MCI_DATAENDMASK,
-	       host->base + MMCIMASK0);
 	return 0;
 }
 
@@ -830,6 +843,7 @@ static struct mmci_host_ops mmci_variant_ops = {
 	.get_next_data = mmci_dmae_get_next_data,
 	.dma_setup = mmci_dmae_setup,
 	.dma_release = mmci_dmae_release,
+	.dma_start = mmci_dmae_start,
 };
 
 void mmci_variant_init(struct mmci_host *host)
@@ -847,11 +861,6 @@ static inline void mmci_dma_data_error(struct mmci_host *host)
 {
 }
 
-static inline int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
-{
-	return -ENOSYS;
-}
-
 #endif
 
 static void mmci_pre_request(struct mmc_host *mmc, struct mmc_request *mrq)
@@ -948,7 +957,7 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data)
 	 * Attempt to use DMA operation mode, if this
 	 * should fail, fall back to PIO mode
 	 */
-	if (!mmci_dma_start_data(host, datactrl))
+	if (!mmci_dma_start(host, datactrl))
 		return;
 
 	/* IRQ mode, map the SG list for CPU reading/writing */
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index a6a85aa..7bca597 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -280,6 +280,7 @@ struct mmci_host_ops {
 	void (*get_next_data)(struct mmci_host *host, struct mmc_data *data);
 	int (*dma_setup)(struct mmci_host *host);
 	void (*dma_release)(struct mmci_host *host);
+	int (*dma_start)(struct mmci_host *host, unsigned int *datactrl);
 };
 
 struct mmci_host {
@@ -339,4 +340,5 @@ void mmci_dmae_unprep_data(struct mmci_host *host, struct mmc_data *data,
 void mmci_dmae_get_next_data(struct mmci_host *host, struct mmc_data *data);
 int mmci_dmae_setup(struct mmci_host *host);
 void mmci_dmae_release(struct mmci_host *host);
+int mmci_dmae_start(struct mmci_host *host, unsigned int *datactrl);
 
diff --git a/drivers/mmc/host/mmci_qcom_dml.c b/drivers/mmc/host/mmci_qcom_dml.c
index da4c43a..66af406 100644
--- a/drivers/mmc/host/mmci_qcom_dml.c
+++ b/drivers/mmc/host/mmci_qcom_dml.c
@@ -189,6 +189,7 @@ static struct mmci_host_ops qcom_variant_ops = {
 	.get_next_data = mmci_dmae_get_next_data,
 	.dma_setup = qcom_dma_setup,
 	.dma_release = mmci_dmae_release,
+	.dma_start = mmci_dmae_start,
 };
 
 void qcom_variant_init(struct mmci_host *host)
-- 
2.7.4

[PATCH V6 07/23] mmc: mmci: add dma_finalize callback

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds dma_finalize callback at mmci_host_ops
to allow to call specific variant.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c          | 19 ++++++++++++-------
 drivers/mmc/host/mmci.h          |  3 ++-
 drivers/mmc/host/mmci_qcom_dml.c |  1 +
 3 files changed, 15 insertions(+), 8 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 72584f4..4570042 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -460,6 +460,15 @@ int mmci_dma_start(struct mmci_host *host, unsigned int datactrl)
 	return 0;
 }
 
+void mmci_dma_finalize(struct mmci_host *host, struct mmc_data *data)
+{
+	if (!host->use_dma)
+		return;
+
+	if (host->ops && host->ops->dma_finalize)
+		host->ops->dma_finalize(host, data);
+}
+
 static void
 mmci_request_end(struct mmci_host *host, struct mmc_request *mrq)
 {
@@ -641,13 +650,13 @@ static void mmci_dma_data_error(struct mmci_host *host)
 	mmci_dma_unmap(host, host->data);
 }
 
-static void mmci_dma_finalize(struct mmci_host *host, struct mmc_data *data)
+void mmci_dmae_finalize(struct mmci_host *host, struct mmc_data *data)
 {
 	struct mmci_dmae_priv *dmae = host->dma_priv;
 	u32 status;
 	int i;
 
-	if (!host->use_dma || !dma_inprogress(host))
+	if (!dma_inprogress(host))
 		return;
 
 	/* Wait up to 1ms for the DMA to complete */
@@ -844,6 +853,7 @@ static struct mmci_host_ops mmci_variant_ops = {
 	.dma_setup = mmci_dmae_setup,
 	.dma_release = mmci_dmae_release,
 	.dma_start = mmci_dmae_start,
+	.dma_finalize = mmci_dmae_finalize,
 };
 
 void mmci_variant_init(struct mmci_host *host)
@@ -852,11 +862,6 @@ void mmci_variant_init(struct mmci_host *host)
 }
 #else
 /* Blank functions if the DMA engine is not available */
-static inline void mmci_dma_finalize(struct mmci_host *host,
-				     struct mmc_data *data)
-{
-}
-
 static inline void mmci_dma_data_error(struct mmci_host *host)
 {
 }
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 7bca597..8c1493b 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -281,6 +281,7 @@ struct mmci_host_ops {
 	int (*dma_setup)(struct mmci_host *host);
 	void (*dma_release)(struct mmci_host *host);
 	int (*dma_start)(struct mmci_host *host, unsigned int *datactrl);
+	void (*dma_finalize)(struct mmci_host *host, struct mmc_data *data);
 };
 
 struct mmci_host {
@@ -341,4 +342,4 @@ void mmci_dmae_get_next_data(struct mmci_host *host, struct mmc_data *data);
 int mmci_dmae_setup(struct mmci_host *host);
 void mmci_dmae_release(struct mmci_host *host);
 int mmci_dmae_start(struct mmci_host *host, unsigned int *datactrl);
-
+void mmci_dmae_finalize(struct mmci_host *host, struct mmc_data *data);
diff --git a/drivers/mmc/host/mmci_qcom_dml.c b/drivers/mmc/host/mmci_qcom_dml.c
index 66af406..c2ef73f 100644
--- a/drivers/mmc/host/mmci_qcom_dml.c
+++ b/drivers/mmc/host/mmci_qcom_dml.c
@@ -190,6 +190,7 @@ static struct mmci_host_ops qcom_variant_ops = {
 	.dma_setup = qcom_dma_setup,
 	.dma_release = mmci_dmae_release,
 	.dma_start = mmci_dmae_start,
+	.dma_finalize = mmci_dmae_finalize,
 };
 
 void qcom_variant_init(struct mmci_host *host)
-- 
2.7.4

[PATCH V6 08/23] mmc: mmci: add dma_error callback

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds dma_error callback at mmci_host_ops
to allow to call specific variant.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c          | 26 +++++++++++++++-----------
 drivers/mmc/host/mmci.h          |  2 ++
 drivers/mmc/host/mmci_qcom_dml.c |  1 +
 3 files changed, 18 insertions(+), 11 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 4570042..3d4431b 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -469,6 +469,15 @@ void mmci_dma_finalize(struct mmci_host *host, struct mmc_data *data)
 		host->ops->dma_finalize(host, data);
 }
 
+void mmci_dma_error(struct mmci_host *host)
+{
+	if (!host->use_dma)
+		return;
+
+	if (host->ops && host->ops->dma_error)
+		host->ops->dma_error(host);
+}
+
 static void
 mmci_request_end(struct mmci_host *host, struct mmc_request *mrq)
 {
@@ -633,11 +642,11 @@ static void mmci_dma_unmap(struct mmci_host *host, struct mmc_data *data)
 		     mmc_get_dma_dir(data));
 }
 
-static void mmci_dma_data_error(struct mmci_host *host)
+void mmci_dmae_error(struct mmci_host *host)
 {
 	struct mmci_dmae_priv *dmae = host->dma_priv;
 
-	if (!host->use_dma || !dma_inprogress(host))
+	if (!dma_inprogress(host))
 		return;
 
 	dev_err(mmc_dev(host->mmc), "error during DMA transfer!\n");
@@ -674,7 +683,7 @@ void mmci_dmae_finalize(struct mmci_host *host, struct mmc_data *data)
 	 * contiguous buffers.  On TX, we'll get a FIFO underrun error.
 	 */
 	if (status & MCI_RXDATAAVLBLMASK) {
-		mmci_dma_data_error(host);
+		mmci_dma_error(host);
 		if (!data->error)
 			data->error = -EIO;
 	} else if (!data->host_cookie) {
@@ -854,18 +863,13 @@ static struct mmci_host_ops mmci_variant_ops = {
 	.dma_release = mmci_dmae_release,
 	.dma_start = mmci_dmae_start,
 	.dma_finalize = mmci_dmae_finalize,
+	.dma_error = mmci_dmae_error,
 };
 
 void mmci_variant_init(struct mmci_host *host)
 {
 	host->ops = &mmci_variant_ops;
 }
-#else
-/* Blank functions if the DMA engine is not available */
-static inline void mmci_dma_data_error(struct mmci_host *host)
-{
-}
-
 #endif
 
 static void mmci_pre_request(struct mmc_host *mmc, struct mmc_request *mrq)
@@ -1037,7 +1041,7 @@ mmci_data_irq(struct mmci_host *host, struct mmc_data *data,
 		u32 remain, success;
 
 		/* Terminate the DMA transfer */
-		mmci_dma_data_error(host);
+		mmci_dma_error(host);
 
 		/*
 		 * Calculate how far we are into the transfer.  Note that
@@ -1183,7 +1187,7 @@ mmci_cmd_irq(struct mmci_host *host, struct mmc_command *cmd,
 	if ((!sbc && !cmd->data) || cmd->error) {
 		if (host->data) {
 			/* Terminate the DMA transfer */
-			mmci_dma_data_error(host);
+			mmci_dma_error(host);
 
 			mmci_stop_data(host);
 		}
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 8c1493b..bcf3e8b 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -282,6 +282,7 @@ struct mmci_host_ops {
 	void (*dma_release)(struct mmci_host *host);
 	int (*dma_start)(struct mmci_host *host, unsigned int *datactrl);
 	void (*dma_finalize)(struct mmci_host *host, struct mmc_data *data);
+	void (*dma_error)(struct mmci_host *host);
 };
 
 struct mmci_host {
@@ -343,3 +344,4 @@ int mmci_dmae_setup(struct mmci_host *host);
 void mmci_dmae_release(struct mmci_host *host);
 int mmci_dmae_start(struct mmci_host *host, unsigned int *datactrl);
 void mmci_dmae_finalize(struct mmci_host *host, struct mmc_data *data);
+void mmci_dmae_error(struct mmci_host *host);
diff --git a/drivers/mmc/host/mmci_qcom_dml.c b/drivers/mmc/host/mmci_qcom_dml.c
index c2ef73f..25d0a75 100644
--- a/drivers/mmc/host/mmci_qcom_dml.c
+++ b/drivers/mmc/host/mmci_qcom_dml.c
@@ -191,6 +191,7 @@ static struct mmci_host_ops qcom_variant_ops = {
 	.dma_release = mmci_dmae_release,
 	.dma_start = mmci_dmae_start,
 	.dma_finalize = mmci_dmae_finalize,
+	.dma_error = mmci_dmae_error,
 };
 
 void qcom_variant_init(struct mmci_host *host)
-- 
2.7.4

[PATCH V6 09/23] mmc: mmci: add validate_data callback

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds validate_data callback at mmci_host_ops
to check specific constraints of variant.
Move mmci_validate_data function to regroup mmci_host_ops interfaces.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 39 +++++++++++++++++++++------------------
 drivers/mmc/host/mmci.h |  1 +
 2 files changed, 22 insertions(+), 18 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 3d4431b..91ef2ede 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -239,24 +239,6 @@ static int mmci_card_busy(struct mmc_host *mmc)
 	return busy;
 }
 
-/*
- * Validate mmc prerequisites
- */
-static int mmci_validate_data(struct mmci_host *host,
-			      struct mmc_data *data)
-{
-	if (!data)
-		return 0;
-
-	if (!is_power_of_2(data->blksz)) {
-		dev_err(mmc_dev(host->mmc),
-			"unsupported block size (%d bytes)\n", data->blksz);
-		return -EINVAL;
-	}
-
-	return 0;
-}
-
 static void mmci_reg_delay(struct mmci_host *host)
 {
 	/*
@@ -392,6 +374,27 @@ void mmci_dma_setup(struct mmci_host *host)
 	host->use_dma = true;
 }
 
+/*
+ * Validate mmc prerequisites
+ */
+static int mmci_validate_data(struct mmci_host *host,
+			      struct mmc_data *data)
+{
+	if (!data)
+		return 0;
+
+	if (!is_power_of_2(data->blksz)) {
+		dev_err(mmc_dev(host->mmc),
+			"unsupported block size (%d bytes)\n", data->blksz);
+		return -EINVAL;
+	}
+
+	if (host->ops && host->ops->validate_data)
+		return host->ops->validate_data(host, data);
+
+	return 0;
+}
+
 int mmci_prep_data(struct mmci_host *host, struct mmc_data *data, bool next)
 {
 	int err;
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index bcf3e8b..ed59baf 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -273,6 +273,7 @@ struct variant_data {
 
 /* mmci variant callbacks */
 struct mmci_host_ops {
+	int (*validate_data)(struct mmci_host *host, struct mmc_data *data);
 	int (*prep_data)(struct mmci_host *host, struct mmc_data *data,
 			 bool next);
 	void (*unprep_data)(struct mmci_host *host, struct mmc_data *data,
-- 
2.7.4

[PATCH V6 10/23] mmc: mmci: add set_clk/pwrreg callbacks

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds set_clkreg and set_pwrreg callbacks
at mmci_host_ops to allow to call specific variant.
extends visibility of mmci_write_clk/pwrreg functions
to be used into specific file variant.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 16 ++++++++++++----
 drivers/mmc/host/mmci.h |  5 +++++
 2 files changed, 17 insertions(+), 4 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 91ef2ede..1b99ae3 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -257,7 +257,7 @@ static void mmci_reg_delay(struct mmci_host *host)
 /*
  * This must be called with host->lock held
  */
-static void mmci_write_clkreg(struct mmci_host *host, u32 clk)
+void mmci_write_clkreg(struct mmci_host *host, u32 clk)
 {
 	if (host->clk_reg != clk) {
 		host->clk_reg = clk;
@@ -268,7 +268,7 @@ static void mmci_write_clkreg(struct mmci_host *host, u32 clk)
 /*
  * This must be called with host->lock held
  */
-static void mmci_write_pwrreg(struct mmci_host *host, u32 pwr)
+void mmci_write_pwrreg(struct mmci_host *host, u32 pwr)
 {
 	if (host->pwr_reg != pwr) {
 		host->pwr_reg = pwr;
@@ -1571,8 +1571,16 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 
 	spin_lock_irqsave(&host->lock, flags);
 
-	mmci_set_clkreg(host, ios->clock);
-	mmci_write_pwrreg(host, pwr);
+	if (host->ops && host->ops->set_clkreg)
+		host->ops->set_clkreg(host, ios->clock);
+	else
+		mmci_set_clkreg(host, ios->clock);
+
+	if (host->ops && host->ops->set_pwrreg)
+		host->ops->set_pwrreg(host, pwr);
+	else
+		mmci_write_pwrreg(host, pwr);
+
 	mmci_reg_delay(host);
 
 	spin_unlock_irqrestore(&host->lock, flags);
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index ed59baf..dbb5ad4 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -284,6 +284,8 @@ struct mmci_host_ops {
 	int (*dma_start)(struct mmci_host *host, unsigned int *datactrl);
 	void (*dma_finalize)(struct mmci_host *host, struct mmc_data *data);
 	void (*dma_error)(struct mmci_host *host);
+	void (*set_clkreg)(struct mmci_host *host, unsigned int desired);
+	void (*set_pwrreg)(struct mmci_host *host, unsigned int pwr);
 };
 
 struct mmci_host {
@@ -336,6 +338,9 @@ struct mmci_host {
 
 #define dma_inprogress(host)	((host)->dma_in_progress)
 
+void mmci_write_clkreg(struct mmci_host *host, u32 clk);
+void mmci_write_pwrreg(struct mmci_host *host, u32 pwr);
+
 int mmci_dmae_prep_data(struct mmci_host *host, struct mmc_data *data,
 			bool next);
 void mmci_dmae_unprep_data(struct mmci_host *host, struct mmc_data *data,
-- 
2.7.4

[PATCH V6 11/23] mmc: mmci: add datactrl block size variant property

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch allows to define a datactrl block size
by variant, requested by STM32 sdmmc variant.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 13 +++++++++++--
 drivers/mmc/host/mmci.h |  2 ++
 2 files changed, 13 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 1b99ae3..0e8b65d 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -57,6 +57,7 @@ static struct variant_data variant_arm = {
 	.fifosize		= 16 * 4,
 	.fifohalfsize		= 8 * 4,
 	.datalength_bits	= 16,
+	.datactrl_blocksz	= 11,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.reversed_irq_handling	= true,
@@ -70,6 +71,7 @@ static struct variant_data variant_arm_extended_fifo = {
 	.fifosize		= 128 * 4,
 	.fifohalfsize		= 64 * 4,
 	.datalength_bits	= 16,
+	.datactrl_blocksz	= 11,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.mmcimask1		= true,
@@ -83,6 +85,7 @@ static struct variant_data variant_arm_extended_fifo_hwfc = {
 	.fifohalfsize		= 64 * 4,
 	.clkreg_enable		= MCI_ARM_HWFCEN,
 	.datalength_bits	= 16,
+	.datactrl_blocksz	= 11,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.mmcimask1		= true,
@@ -97,6 +100,7 @@ static struct variant_data variant_u300 = {
 	.clkreg_enable		= MCI_ST_U300_HWFCEN,
 	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
 	.datalength_bits	= 16,
+	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio			= true,
 	.pwrreg_powerup		= MCI_PWR_ON,
@@ -116,6 +120,7 @@ static struct variant_data variant_nomadik = {
 	.clkreg			= MCI_CLK_ENABLE,
 	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
 	.datalength_bits	= 24,
+	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
@@ -138,6 +143,7 @@ static struct variant_data variant_ux500 = {
 	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
 	.clkreg_neg_edge_enable	= MCI_ST_UX500_NEG_EDGE,
 	.datalength_bits	= 24,
+	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
@@ -165,6 +171,7 @@ static struct variant_data variant_ux500v2 = {
 	.clkreg_neg_edge_enable	= MCI_ST_UX500_NEG_EDGE,
 	.datactrl_mask_ddrmode	= MCI_DPSM_ST_DDRMODE,
 	.datalength_bits	= 24,
+	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
@@ -192,6 +199,7 @@ static struct variant_data variant_stm32 = {
 	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
 	.clkreg_neg_edge_enable	= MCI_ST_UX500_NEG_EDGE,
 	.datalength_bits	= 24,
+	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
@@ -213,6 +221,7 @@ static struct variant_data variant_qcom = {
 	.data_cmd_enable	= MCI_CPSM_QCOM_DATCMD,
 	.blksz_datactrl4	= true,
 	.datalength_bits	= 24,
+	.datactrl_blocksz	= 11,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 208000000,
 	.explicit_mclk_control	= true,
@@ -1861,13 +1870,13 @@ static int mmci_probe(struct amba_device *dev,
 	/*
 	 * Block size can be up to 2048 bytes, but must be a power of two.
 	 */
-	mmc->max_blk_size = 1 << 11;
+	mmc->max_blk_size = 1 << variant->datactrl_blocksz;
 
 	/*
 	 * Limit the number of blocks transferred so that we don't overflow
 	 * the maximum request size.
 	 */
-	mmc->max_blk_count = mmc->max_req_size >> 11;
+	mmc->max_blk_count = mmc->max_req_size >> variant->datactrl_blocksz;
 
 	spin_lock_init(&host->lock);
 
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index dbb5ad4..d5979e8 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -217,6 +217,7 @@ struct mmci_host;
  * @blksz_datactrl4: true if Block size is at b4..b16 position in datactrl
  *		     register
  * @datactrl_mask_sdio: SDIO enable mask in datactrl register
+ * @datactrl_blksz: block size in power of two
  * @pwrreg_powerup: power up value for MMCIPOWER register
  * @f_max: maximum clk frequency supported by the controller.
  * @signal_direction: input/out direction of bus signals can be indicated
@@ -248,6 +249,7 @@ struct variant_data {
 	unsigned int		data_cmd_enable;
 	unsigned int		datactrl_mask_ddrmode;
 	unsigned int		datactrl_mask_sdio;
+	unsigned int		datactrl_blocksz;
 	u8			st_sdio:1;
 	u8			st_clkdiv:1;
 	u8			blksz_datactrl16:1;
-- 
2.7.4

[PATCH V6 12/23] mmc: mmci: expand startbiterr to irqmask and error check

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

All variants don't pretend to have a startbiterr.
-While data error check, if status register return an error
(like  MCI_DATACRCFAIL) we must avoid to check MCI_STARTBITERR
(if not desired).
-expand start_err to MCI_IRQENABLE to avoid to set this bit by default.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 27 ++++++++++++++++-----------
 drivers/mmc/host/mmci.h |  6 +++---
 2 files changed, 19 insertions(+), 14 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 0e8b65d..737adf4 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -1042,14 +1042,18 @@ static void
 mmci_data_irq(struct mmci_host *host, struct mmc_data *data,
 	      unsigned int status)
 {
+	unsigned int status_err;
+
 	/* Make sure we have data to handle */
 	if (!data)
 		return;
 
 	/* First check for errors */
-	if (status & (MCI_DATACRCFAIL | MCI_DATATIMEOUT |
-		      host->variant->start_err |
-		      MCI_TXUNDERRUN | MCI_RXOVERRUN)) {
+	status_err = status & (host->variant->start_err |
+			       MCI_DATACRCFAIL | MCI_DATATIMEOUT |
+			       MCI_TXUNDERRUN | MCI_RXOVERRUN);
+
+	if (status_err) {
 		u32 remain, success;
 
 		/* Terminate the DMA transfer */
@@ -1066,18 +1070,18 @@ mmci_data_irq(struct mmci_host *host, struct mmc_data *data,
 		success = data->blksz * data->blocks - remain;
 
 		dev_dbg(mmc_dev(host->mmc), "MCI ERROR IRQ, status 0x%08x at 0x%08x\n",
-			status, success);
-		if (status & MCI_DATACRCFAIL) {
+			status_err, success);
+		if (status_err & MCI_DATACRCFAIL) {
 			/* Last block was not successful */
 			success -= 1;
 			data->error = -EILSEQ;
-		} else if (status & MCI_DATATIMEOUT) {
+		} else if (status_err & MCI_DATATIMEOUT) {
 			data->error = -ETIMEDOUT;
-		} else if (status & MCI_STARTBITERR) {
+		} else if (status_err & MCI_STARTBITERR) {
 			data->error = -ECOMM;
-		} else if (status & MCI_TXUNDERRUN) {
+		} else if (status_err & MCI_TXUNDERRUN) {
 			data->error = -EIO;
-		} else if (status & MCI_RXOVERRUN) {
+		} else if (status_err & MCI_RXOVERRUN) {
 			if (success > host->variant->fifosize)
 				success -= host->variant->fifosize;
 			else
@@ -1918,7 +1922,7 @@ static int mmci_probe(struct amba_device *dev,
 			goto clk_disable;
 	}
 
-	writel(MCI_IRQENABLE, host->base + MMCIMASK0);
+	writel(MCI_IRQENABLE | variant->start_err, host->base + MMCIMASK0);
 
 	amba_set_drvdata(dev, mmc);
 
@@ -2005,7 +2009,8 @@ static void mmci_restore(struct mmci_host *host)
 		writel(host->datactrl_reg, host->base + MMCIDATACTRL);
 		writel(host->pwr_reg, host->base + MMCIPOWER);
 	}
-	writel(MCI_IRQENABLE, host->base + MMCIMASK0);
+	writel(MCI_IRQENABLE | host->variant->start_err,
+	       host->base + MMCIMASK0);
 	mmci_reg_delay(host);
 
 	spin_unlock_irqrestore(&host->lock, flags);
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index d5979e8..8e7ea44 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -181,9 +181,9 @@
 #define MMCIFIFO		0x080 /* to 0x0bc */
 
 #define MCI_IRQENABLE	\
-	(MCI_CMDCRCFAILMASK|MCI_DATACRCFAILMASK|MCI_CMDTIMEOUTMASK|	\
-	MCI_DATATIMEOUTMASK|MCI_TXUNDERRUNMASK|MCI_RXOVERRUNMASK|	\
-	MCI_CMDRESPENDMASK|MCI_CMDSENTMASK|MCI_STARTBITERRMASK)
+	(MCI_CMDCRCFAILMASK | MCI_DATACRCFAILMASK | MCI_CMDTIMEOUTMASK | \
+	MCI_DATATIMEOUTMASK | MCI_TXUNDERRUNMASK | MCI_RXOVERRUNMASK |	\
+	MCI_CMDRESPENDMASK | MCI_CMDSENTMASK)
 
 /* These interrupts are directed to IRQ1 when two IRQ lines are available */
 #define MCI_IRQ1MASK \
-- 
2.7.4

[PATCH V6 13/23] mmc: mmci: add variant properties to define cpsm & cmdresp bits

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds command variant properties to define
cpsm enable bit and responses.
Needed to support the STM32 variant (shift of cpsm bit,
specific definition of commands response).

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 47 +++++++++++++++++++++++++++++++++++++++++++----
 drivers/mmc/host/mmci.h |  8 ++++++++
 2 files changed, 51 insertions(+), 4 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 737adf4..9f0cef0 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -56,6 +56,10 @@ static unsigned int fmax = 515633;
 static struct variant_data variant_arm = {
 	.fifosize		= 16 * 4,
 	.fifohalfsize		= 8 * 4,
+	.cmdreg_cpsm_enable	= MCI_CPSM_ENABLE,
+	.cmdreg_lrsp_crc	= MCI_CPSM_RESPONSE | MCI_CPSM_LONGRSP,
+	.cmdreg_srsp_crc	= MCI_CPSM_RESPONSE,
+	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 16,
 	.datactrl_blocksz	= 11,
 	.pwrreg_powerup		= MCI_PWR_UP,
@@ -70,6 +74,10 @@ static struct variant_data variant_arm = {
 static struct variant_data variant_arm_extended_fifo = {
 	.fifosize		= 128 * 4,
 	.fifohalfsize		= 64 * 4,
+	.cmdreg_cpsm_enable	= MCI_CPSM_ENABLE,
+	.cmdreg_lrsp_crc	= MCI_CPSM_RESPONSE | MCI_CPSM_LONGRSP,
+	.cmdreg_srsp_crc	= MCI_CPSM_RESPONSE,
+	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 16,
 	.datactrl_blocksz	= 11,
 	.pwrreg_powerup		= MCI_PWR_UP,
@@ -84,6 +92,10 @@ static struct variant_data variant_arm_extended_fifo_hwfc = {
 	.fifosize		= 128 * 4,
 	.fifohalfsize		= 64 * 4,
 	.clkreg_enable		= MCI_ARM_HWFCEN,
+	.cmdreg_cpsm_enable	= MCI_CPSM_ENABLE,
+	.cmdreg_lrsp_crc	= MCI_CPSM_RESPONSE | MCI_CPSM_LONGRSP,
+	.cmdreg_srsp_crc	= MCI_CPSM_RESPONSE,
+	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 16,
 	.datactrl_blocksz	= 11,
 	.pwrreg_powerup		= MCI_PWR_UP,
@@ -99,6 +111,10 @@ static struct variant_data variant_u300 = {
 	.fifohalfsize		= 8 * 4,
 	.clkreg_enable		= MCI_ST_U300_HWFCEN,
 	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
+	.cmdreg_cpsm_enable	= MCI_CPSM_ENABLE,
+	.cmdreg_lrsp_crc	= MCI_CPSM_RESPONSE | MCI_CPSM_LONGRSP,
+	.cmdreg_srsp_crc	= MCI_CPSM_RESPONSE,
+	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 16,
 	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
@@ -119,6 +135,10 @@ static struct variant_data variant_nomadik = {
 	.fifohalfsize		= 8 * 4,
 	.clkreg			= MCI_CLK_ENABLE,
 	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
+	.cmdreg_cpsm_enable	= MCI_CPSM_ENABLE,
+	.cmdreg_lrsp_crc	= MCI_CPSM_RESPONSE | MCI_CPSM_LONGRSP,
+	.cmdreg_srsp_crc	= MCI_CPSM_RESPONSE,
+	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 24,
 	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
@@ -142,6 +162,10 @@ static struct variant_data variant_ux500 = {
 	.clkreg_enable		= MCI_ST_UX500_HWFCEN,
 	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
 	.clkreg_neg_edge_enable	= MCI_ST_UX500_NEG_EDGE,
+	.cmdreg_cpsm_enable	= MCI_CPSM_ENABLE,
+	.cmdreg_lrsp_crc	= MCI_CPSM_RESPONSE | MCI_CPSM_LONGRSP,
+	.cmdreg_srsp_crc	= MCI_CPSM_RESPONSE,
+	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 24,
 	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
@@ -169,6 +193,10 @@ static struct variant_data variant_ux500v2 = {
 	.clkreg_enable		= MCI_ST_UX500_HWFCEN,
 	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
 	.clkreg_neg_edge_enable	= MCI_ST_UX500_NEG_EDGE,
+	.cmdreg_cpsm_enable	= MCI_CPSM_ENABLE,
+	.cmdreg_lrsp_crc	= MCI_CPSM_RESPONSE | MCI_CPSM_LONGRSP,
+	.cmdreg_srsp_crc	= MCI_CPSM_RESPONSE,
+	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datactrl_mask_ddrmode	= MCI_DPSM_ST_DDRMODE,
 	.datalength_bits	= 24,
 	.datactrl_blocksz	= 11,
@@ -198,6 +226,10 @@ static struct variant_data variant_stm32 = {
 	.clkreg_enable		= MCI_ST_UX500_HWFCEN,
 	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
 	.clkreg_neg_edge_enable	= MCI_ST_UX500_NEG_EDGE,
+	.cmdreg_cpsm_enable	= MCI_CPSM_ENABLE,
+	.cmdreg_lrsp_crc	= MCI_CPSM_RESPONSE | MCI_CPSM_LONGRSP,
+	.cmdreg_srsp_crc	= MCI_CPSM_RESPONSE,
+	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 24,
 	.datactrl_blocksz	= 11,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
@@ -218,6 +250,10 @@ static struct variant_data variant_qcom = {
 				  MCI_QCOM_CLK_SELECT_IN_FBCLK,
 	.clkreg_8bit_bus_enable = MCI_QCOM_CLK_WIDEBUS_8,
 	.datactrl_mask_ddrmode	= MCI_QCOM_CLK_SELECT_IN_DDR_MODE,
+	.cmdreg_cpsm_enable	= MCI_CPSM_ENABLE,
+	.cmdreg_lrsp_crc	= MCI_CPSM_RESPONSE | MCI_CPSM_LONGRSP,
+	.cmdreg_srsp_crc	= MCI_CPSM_RESPONSE,
+	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.data_cmd_enable	= MCI_CPSM_QCOM_DATCMD,
 	.blksz_datactrl4	= true,
 	.datalength_bits	= 24,
@@ -1015,16 +1051,19 @@ mmci_start_command(struct mmci_host *host, struct mmc_command *cmd, u32 c)
 	dev_dbg(mmc_dev(host->mmc), "op %02x arg %08x flags %08x\n",
 	    cmd->opcode, cmd->arg, cmd->flags);
 
-	if (readl(base + MMCICOMMAND) & MCI_CPSM_ENABLE) {
+	if (readl(base + MMCICOMMAND) & host->variant->cmdreg_cpsm_enable) {
 		writel(0, base + MMCICOMMAND);
 		mmci_reg_delay(host);
 	}
 
-	c |= cmd->opcode | MCI_CPSM_ENABLE;
+	c |= cmd->opcode | host->variant->cmdreg_cpsm_enable;
 	if (cmd->flags & MMC_RSP_PRESENT) {
 		if (cmd->flags & MMC_RSP_136)
-			c |= MCI_CPSM_LONGRSP;
-		c |= MCI_CPSM_RESPONSE;
+			c |= host->variant->cmdreg_lrsp_crc;
+		else if (cmd->flags & MMC_RSP_CRC)
+			c |= host->variant->cmdreg_srsp_crc;
+		else
+			c |= host->variant->cmdreg_srsp;
 	}
 	if (/*interrupt*/0)
 		c |= MCI_CPSM_INTERRUPT;
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 8e7ea44..531c247 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -204,6 +204,10 @@ struct mmci_host;
  * @clkreg_enable: enable value for MMCICLOCK register
  * @clkreg_8bit_bus_enable: enable value for 8 bit bus
  * @clkreg_neg_edge_enable: enable value for inverted data/cmd output
+ * @cmdreg_cpsm_enable: enable value for CPSM
+ * @cmdreg_lrsp_crc: enable value for long response with crc
+ * @cmdreg_srsp_crc: enable value for short response with crc
+ * @cmdreg_srsp: enable value for short response without crc
  * @datalength_bits: number of bits in the MMCIDATALENGTH register
  * @fifosize: number of bytes that can be written when MMCI_TXFIFOEMPTY
  *	      is asserted (likewise for RX)
@@ -243,6 +247,10 @@ struct variant_data {
 	unsigned int		clkreg_enable;
 	unsigned int		clkreg_8bit_bus_enable;
 	unsigned int		clkreg_neg_edge_enable;
+	unsigned int		cmdreg_cpsm_enable;
+	unsigned int		cmdreg_lrsp_crc;
+	unsigned int		cmdreg_srsp_crc;
+	unsigned int		cmdreg_srsp;
 	unsigned int		datalength_bits;
 	unsigned int		fifosize;
 	unsigned int		fifohalfsize;
-- 
2.7.4

[PATCH V6 14/23] mmc: mmci: add variant property to define dpsm bit

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds datactrl variant property to define
dpsm enable bit. Needed to support the STM32 variant
(STM32 has no dpsm enable bit).

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 15 ++++++++++++---
 drivers/mmc/host/mmci.h |  2 ++
 2 files changed, 14 insertions(+), 3 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 9f0cef0..0443b3a 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -62,6 +62,7 @@ static struct variant_data variant_arm = {
 	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 16,
 	.datactrl_blocksz	= 11,
+	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.reversed_irq_handling	= true,
@@ -80,6 +81,7 @@ static struct variant_data variant_arm_extended_fifo = {
 	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 16,
 	.datactrl_blocksz	= 11,
+	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.mmcimask1		= true,
@@ -98,6 +100,7 @@ static struct variant_data variant_arm_extended_fifo_hwfc = {
 	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 16,
 	.datactrl_blocksz	= 11,
+	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.mmcimask1		= true,
@@ -117,6 +120,7 @@ static struct variant_data variant_u300 = {
 	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 16,
 	.datactrl_blocksz	= 11,
+	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio			= true,
 	.pwrreg_powerup		= MCI_PWR_ON,
@@ -141,6 +145,7 @@ static struct variant_data variant_nomadik = {
 	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 24,
 	.datactrl_blocksz	= 11,
+	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
@@ -168,6 +173,7 @@ static struct variant_data variant_ux500 = {
 	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 24,
 	.datactrl_blocksz	= 11,
+	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
@@ -200,6 +206,7 @@ static struct variant_data variant_ux500v2 = {
 	.datactrl_mask_ddrmode	= MCI_DPSM_ST_DDRMODE,
 	.datalength_bits	= 24,
 	.datactrl_blocksz	= 11,
+	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
@@ -232,6 +239,7 @@ static struct variant_data variant_stm32 = {
 	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
 	.datalength_bits	= 24,
 	.datactrl_blocksz	= 11,
+	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
@@ -258,6 +266,7 @@ static struct variant_data variant_qcom = {
 	.blksz_datactrl4	= true,
 	.datalength_bits	= 24,
 	.datactrl_blocksz	= 11,
+	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 208000000,
 	.explicit_mclk_control	= true,
@@ -976,11 +985,11 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data)
 	BUG_ON(1 << blksz_bits != data->blksz);
 
 	if (variant->blksz_datactrl16)
-		datactrl = MCI_DPSM_ENABLE | (data->blksz << 16);
+		datactrl = variant->datactrl_dpsm_enable | (data->blksz << 16);
 	else if (variant->blksz_datactrl4)
-		datactrl = MCI_DPSM_ENABLE | (data->blksz << 4);
+		datactrl = variant->datactrl_dpsm_enable | (data->blksz << 4);
 	else
-		datactrl = MCI_DPSM_ENABLE | blksz_bits << 4;
+		datactrl = variant->datactrl_dpsm_enable | blksz_bits << 4;
 
 	if (data->flags & MMC_DATA_READ)
 		datactrl |= MCI_DPSM_DIRECTION;
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 531c247..04d021e 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -222,6 +222,7 @@ struct mmci_host;
  *		     register
  * @datactrl_mask_sdio: SDIO enable mask in datactrl register
  * @datactrl_blksz: block size in power of two
+ * @datactrl_dpsm_enable: enable value for DPSM
  * @pwrreg_powerup: power up value for MMCIPOWER register
  * @f_max: maximum clk frequency supported by the controller.
  * @signal_direction: input/out direction of bus signals can be indicated
@@ -258,6 +259,7 @@ struct variant_data {
 	unsigned int		datactrl_mask_ddrmode;
 	unsigned int		datactrl_mask_sdio;
 	unsigned int		datactrl_blocksz;
+	unsigned int		datactrl_dpsm_enable;
 	u8			st_sdio:1;
 	u8			st_clkdiv:1;
 	u8			blksz_datactrl16:1;
-- 
2.7.4

[PATCH V6 15/23] mmc: mmci: add variant property to define irq pio mask

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch allows to define specific pio mask for variants.
Needed to support the STM32 sdmmc variant which has some bits
with different meaning (bits: 21,20,13,12,9)

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 13 +++++++++++--
 drivers/mmc/host/mmci.h |  5 ++++-
 2 files changed, 15 insertions(+), 3 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 0443b3a..ca442fb 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -67,6 +67,7 @@ static struct variant_data variant_arm = {
 	.f_max			= 100000000,
 	.reversed_irq_handling	= true,
 	.mmcimask1		= true,
+	.irq_pio_mask		= MCI_IRQ_PIO_MASK,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_ROD,
 	.init			= mmci_variant_init,
@@ -85,6 +86,7 @@ static struct variant_data variant_arm_extended_fifo = {
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.mmcimask1		= true,
+	.irq_pio_mask		= MCI_IRQ_PIO_MASK,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_ROD,
 	.init			= mmci_variant_init,
@@ -104,6 +106,7 @@ static struct variant_data variant_arm_extended_fifo_hwfc = {
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.mmcimask1		= true,
+	.irq_pio_mask		= MCI_IRQ_PIO_MASK,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_ROD,
 	.init			= mmci_variant_init,
@@ -129,6 +132,7 @@ static struct variant_data variant_u300 = {
 	.pwrreg_clkgate		= true,
 	.pwrreg_nopower		= true,
 	.mmcimask1		= true,
+	.irq_pio_mask		= MCI_IRQ_PIO_MASK,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_OD,
 	.init			= mmci_variant_init,
@@ -155,6 +159,7 @@ static struct variant_data variant_nomadik = {
 	.pwrreg_clkgate		= true,
 	.pwrreg_nopower		= true,
 	.mmcimask1		= true,
+	.irq_pio_mask		= MCI_IRQ_PIO_MASK,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_OD,
 	.init			= mmci_variant_init,
@@ -187,6 +192,7 @@ static struct variant_data variant_ux500 = {
 	.busy_detect_mask	= MCI_ST_BUSYENDMASK,
 	.pwrreg_nopower		= true,
 	.mmcimask1		= true,
+	.irq_pio_mask		= MCI_IRQ_PIO_MASK,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_OD,
 	.init			= mmci_variant_init,
@@ -221,6 +227,7 @@ static struct variant_data variant_ux500v2 = {
 	.busy_detect_mask	= MCI_ST_BUSYENDMASK,
 	.pwrreg_nopower		= true,
 	.mmcimask1		= true,
+	.irq_pio_mask		= MCI_IRQ_PIO_MASK,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_OD,
 	.init			= mmci_variant_init,
@@ -237,6 +244,7 @@ static struct variant_data variant_stm32 = {
 	.cmdreg_lrsp_crc	= MCI_CPSM_RESPONSE | MCI_CPSM_LONGRSP,
 	.cmdreg_srsp_crc	= MCI_CPSM_RESPONSE,
 	.cmdreg_srsp		= MCI_CPSM_RESPONSE,
+	.irq_pio_mask		= MCI_IRQ_PIO_MASK,
 	.datalength_bits	= 24,
 	.datactrl_blocksz	= 11,
 	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
@@ -273,6 +281,7 @@ static struct variant_data variant_qcom = {
 	.qcom_fifo		= true,
 	.qcom_dml		= true,
 	.mmcimask1		= true,
+	.irq_pio_mask		= MCI_IRQ_PIO_MASK,
 	.start_err		= MCI_STARTBITERR,
 	.opendrain		= MCI_ROD,
 	.init			= qcom_variant_init,
@@ -556,7 +565,7 @@ static void mmci_set_mask1(struct mmci_host *host, unsigned int mask)
 	if (host->singleirq) {
 		unsigned int mask0 = readl(base + MMCIMASK0);
 
-		mask0 &= ~MCI_IRQ1MASK;
+		mask0 &= ~variant->irq_pio_mask;
 		mask0 |= mask;
 
 		writel(mask0, base + MMCIMASK0);
@@ -1458,7 +1467,7 @@ static irqreturn_t mmci_irq(int irq, void *dev_id)
 			if (status & host->mask1_reg)
 				mmci_pio_irq(irq, dev_id);
 
-			status &= ~MCI_IRQ1MASK;
+			status &= ~host->variant->irq_pio_mask;
 		}
 
 		/*
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 04d021e..783a7ad 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -186,7 +186,7 @@
 	MCI_CMDRESPENDMASK | MCI_CMDSENTMASK)
 
 /* These interrupts are directed to IRQ1 when two IRQ lines are available */
-#define MCI_IRQ1MASK \
+#define MCI_IRQ_PIO_MASK \
 	(MCI_RXFIFOHALFFULLMASK | MCI_RXDATAAVLBLMASK | \
 	 MCI_TXFIFOHALFEMPTYMASK)
 
@@ -239,6 +239,8 @@ struct mmci_host;
  * @qcom_dml: enables qcom specific dma glue for dma transfers.
  * @reversed_irq_handling: handle data irq before cmd irq.
  * @mmcimask1: true if variant have a MMCIMASK1 register.
+ * @irq_pio_mask: bitmask used to manage interrupt pio transfert in mmcimask
+ *		  register
  * @start_err: bitmask identifying the STARTBITERR bit inside MMCISTATUS
  *	       register.
  * @opendrain: bitmask identifying the OPENDRAIN bit inside MMCIPOWER register
@@ -278,6 +280,7 @@ struct variant_data {
 	u8			qcom_dml:1;
 	u8			reversed_irq_handling:1;
 	u8			mmcimask1:1;
+	unsigned int		irq_pio_mask;
 	u32			start_err;
 	u32			opendrain;
 	void (*init)(struct mmci_host *host);
-- 
2.7.4

[PATCH V6 16/23] mmc: mmci: add variant property to write datactrl before command

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds a boolean property to allow to write datactrl
before to send command, whatever the command type (read or write).
Needed to support the STM32 sdmmc variant.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 6 ++++--
 drivers/mmc/host/mmci.h | 2 ++
 2 files changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index ca442fb..66aa59f 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -1267,7 +1267,8 @@ mmci_cmd_irq(struct mmci_host *host, struct mmc_command *cmd,
 		mmci_request_end(host, host->mrq);
 	} else if (sbc) {
 		mmci_start_command(host, host->mrq->cmd, 0);
-	} else if (!(cmd->data->flags & MMC_DATA_READ)) {
+	} else if (!host->variant->datactrl_first &&
+		   !(cmd->data->flags & MMC_DATA_READ)) {
 		mmci_start_data(host, cmd->data);
 	}
 }
@@ -1531,7 +1532,8 @@ static void mmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
 	if (mrq->data)
 		mmci_get_next_data(host, mrq->data);
 
-	if (mrq->data && mrq->data->flags & MMC_DATA_READ)
+	if (mrq->data &&
+	    (host->variant->datactrl_first || mrq->data->flags & MMC_DATA_READ))
 		mmci_start_data(host, mrq->data);
 
 	if (mrq->sbc)
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 783a7ad..eef7dd5 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -223,6 +223,7 @@ struct mmci_host;
  * @datactrl_mask_sdio: SDIO enable mask in datactrl register
  * @datactrl_blksz: block size in power of two
  * @datactrl_dpsm_enable: enable value for DPSM
+ * @datactrl_first: true if data must be setup before send command
  * @pwrreg_powerup: power up value for MMCIPOWER register
  * @f_max: maximum clk frequency supported by the controller.
  * @signal_direction: input/out direction of bus signals can be indicated
@@ -262,6 +263,7 @@ struct variant_data {
 	unsigned int		datactrl_mask_sdio;
 	unsigned int		datactrl_blocksz;
 	unsigned int		datactrl_dpsm_enable;
+	u8			datactrl_first:1;
 	u8			st_sdio:1;
 	u8			st_clkdiv:1;
 	u8			blksz_datactrl16:1;
-- 
2.7.4

[PATCH V6 17/23] mmc: mmci: add variant property to not read datacnt

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds a boolean property to not read datacnt register.
Needed to support the STM32 sdmmc variant. MMCIDATACNT
register should be read only after the data transfer is completed.
When reading after an error event the read data count value may be
different from the real number of data bytes transferred.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 8 ++++++--
 drivers/mmc/host/mmci.h | 3 +++
 2 files changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 66aa59f..7607599 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -1123,8 +1123,12 @@ mmci_data_irq(struct mmci_host *host, struct mmc_data *data,
 		 * can be as much as a FIFO-worth of data ahead.  This
 		 * matters for FIFO overruns only.
 		 */
-		remain = readl(host->base + MMCIDATACNT);
-		success = data->blksz * data->blocks - remain;
+		if (!host->variant->datacnt_useless) {
+			remain = readl(host->base + MMCIDATACNT);
+			success = data->blksz * data->blocks - remain;
+		} else {
+			success = 0;
+		}
 
 		dev_dbg(mmc_dev(host->mmc), "MCI ERROR IRQ, status 0x%08x at 0x%08x\n",
 			status_err, success);
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index eef7dd5..cdcadd2 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -224,6 +224,8 @@ struct mmci_host;
  * @datactrl_blksz: block size in power of two
  * @datactrl_dpsm_enable: enable value for DPSM
  * @datactrl_first: true if data must be setup before send command
+ * @datacnt_useless: true if you could not use datacnt register to read
+ *		     remaining data
  * @pwrreg_powerup: power up value for MMCIPOWER register
  * @f_max: maximum clk frequency supported by the controller.
  * @signal_direction: input/out direction of bus signals can be indicated
@@ -264,6 +266,7 @@ struct variant_data {
 	unsigned int		datactrl_blocksz;
 	unsigned int		datactrl_dpsm_enable;
 	u8			datactrl_first:1;
+	u8			datacnt_useless:1;
 	u8			st_sdio:1;
 	u8			st_clkdiv:1;
 	u8			blksz_datactrl16:1;
-- 
2.7.4

[PATCH V6 18/23] dt-bindings: mmci: add optional reset property

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds a optional reset management.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/mmc/mmci.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt
index 03796cf..4e69b25 100644
--- a/Documentation/devicetree/bindings/mmc/mmci.txt
+++ b/Documentation/devicetree/bindings/mmc/mmci.txt
@@ -15,6 +15,7 @@ Required properties:
 Optional properties:
 - arm,primecell-periphid : contains the PrimeCell Peripheral ID, it overrides
                            the ID provided by the HW
+- resets                 : phandle to internal reset line.
 - vqmmc-supply           : phandle to the regulator device tree node, mentioned
                            as the VCCQ/VDD_IO supply in the eMMC/SD specs.
 - st,sig-dir-dat0        : bus signal direction pin used for DAT[0].
-- 
2.7.4

[PATCH V6 19/23] mmc: mmci: add optional reset property

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds a optional reset management.
STM32 sdmmc variant needs to reset hardware block
during the power cycle procedure (for re-initialization).

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 7 +++++++
 drivers/mmc/host/mmci.h | 2 ++
 2 files changed, 9 insertions(+)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 7607599..d636a0e 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -36,6 +36,7 @@
 #include <linux/pm_runtime.h>
 #include <linux/types.h>
 #include <linux/pinctrl/consumer.h>
+#include <linux/reset.h>
 
 #include <asm/div64.h>
 #include <asm/io.h>
@@ -1882,6 +1883,12 @@ static int mmci_probe(struct amba_device *dev,
 
 	dev_dbg(mmc_dev(mmc), "clocking block at %u Hz\n", mmc->f_max);
 
+	host->rst = devm_reset_control_get_optional_exclusive(&dev->dev, NULL);
+	if (IS_ERR(host->rst)) {
+		ret = PTR_ERR(host->rst);
+		goto clk_disable;
+	}
+
 	/* Get regulators and the supported OCR mask */
 	ret = mmc_regulator_get_supply(mmc);
 	if (ret)
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index cdcadd2..8ecb1ee 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -318,6 +318,8 @@ struct mmci_host {
 	struct clk		*clk;
 	u8			singleirq:1;
 
+	struct reset_control	*rst;
+
 	spinlock_t		lock;
 
 	unsigned int		mclk;
-- 
2.7.4

[PATCH V6 20/23] mmc: mmci: add clock divider for stm32 sdmmc

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

The STM32 sdmmc variant has a different clock divider.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 2 ++
 drivers/mmc/host/mmci.h | 2 ++
 2 files changed, 4 insertions(+)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index d636a0e..ad2f62f 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -1862,6 +1862,8 @@ static int mmci_probe(struct amba_device *dev,
 	 */
 	if (variant->st_clkdiv)
 		mmc->f_min = DIV_ROUND_UP(host->mclk, 257);
+	else if (variant->stm32_clkdiv)
+		mmc->f_min = DIV_ROUND_UP(host->mclk, 2046);
 	else if (variant->explicit_mclk_control)
 		mmc->f_min = clk_round_rate(host->clk, 100000);
 	else
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 8ecb1ee..a962cfa 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -216,6 +216,7 @@ struct mmci_host;
  * @data_cmd_enable: enable value for data commands.
  * @st_sdio: enable ST specific SDIO logic
  * @st_clkdiv: true if using a ST-specific clock divider algorithm
+ * @stm32_clkdiv: true if using a STM32-specific clock divider algorithm
  * @datactrl_mask_ddrmode: ddr mode mask in datactrl register.
  * @blksz_datactrl16: true if Block size is at b16..b30 position in datactrl register
  * @blksz_datactrl4: true if Block size is at b4..b16 position in datactrl
@@ -269,6 +270,7 @@ struct variant_data {
 	u8			datacnt_useless:1;
 	u8			st_sdio:1;
 	u8			st_clkdiv:1;
+	u8			stm32_clkdiv:1;
 	u8			blksz_datactrl16:1;
 	u8			blksz_datactrl4:1;
 	u32			pwrreg_powerup;
-- 
2.7.4

[PATCH V6 21/23] mmc: mmci: add stm32 sdmmc registers

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds stm32 sdmmc specific registers.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.h | 56 +++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 56 insertions(+)

diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index a962cfa..e242f44 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -23,6 +23,14 @@
 #define MCI_ST_DATA31DIREN	(1 << 5)
 #define MCI_ST_FBCLKEN		(1 << 7)
 #define MCI_ST_DATA74DIREN	(1 << 8)
+/*
+ * The STM32 sdmmc does not have PWR_UP/OD/ROD
+ * and uses the power register for
+ */
+#define MCI_STM32_PWR_CYC	0x02
+#define MCI_STM32_VSWITCH	BIT(2)
+#define MCI_STM32_VSWITCHEN	BIT(3)
+#define MCI_STM32_DIRPOL	BIT(4)
 
 #define MMCICLOCK		0x004
 #define MCI_CLK_ENABLE		(1 << 8)
@@ -50,6 +58,19 @@
 #define MCI_QCOM_CLK_SELECT_IN_FBCLK	BIT(15)
 #define MCI_QCOM_CLK_SELECT_IN_DDR_MODE	(BIT(14) | BIT(15))
 
+/* Modified on STM32 sdmmc */
+#define MCI_STM32_CLK_CLKDIV_MSK	GENMASK(9, 0)
+#define MCI_STM32_CLK_WIDEBUS_4		BIT(14)
+#define MCI_STM32_CLK_WIDEBUS_8		BIT(15)
+#define MCI_STM32_CLK_NEGEDGE		BIT(16)
+#define MCI_STM32_CLK_HWFCEN		BIT(17)
+#define MCI_STM32_CLK_DDR		BIT(18)
+#define MCI_STM32_CLK_BUSSPEED		BIT(19)
+#define MCI_STM32_CLK_SEL_MSK		GENMASK(21, 20)
+#define MCI_STM32_CLK_SELCK		(0 << 20)
+#define MCI_STM32_CLK_SELCKIN		(1 << 20)
+#define MCI_STM32_CLK_SELFBCK		(2 << 20)
+
 #define MMCIARGUMENT		0x008
 
 /* The command register controls the Command Path State Machine (CPSM) */
@@ -72,6 +93,15 @@
 #define MCI_CPSM_QCOM_CCSDISABLE	BIT(15)
 #define MCI_CPSM_QCOM_AUTO_CMD19	BIT(16)
 #define MCI_CPSM_QCOM_AUTO_CMD21	BIT(21)
+/* Command register in STM32 sdmmc versions */
+#define MCI_CPSM_STM32_CMDTRANS		BIT(6)
+#define MCI_CPSM_STM32_CMDSTOP		BIT(7)
+#define MCI_CPSM_STM32_WAITRESP_MASK	GENMASK(9, 8)
+#define MCI_CPSM_STM32_NORSP		(0 << 8)
+#define MCI_CPSM_STM32_SRSP_CRC		(1 << 8)
+#define MCI_CPSM_STM32_SRSP		(2 << 8)
+#define MCI_CPSM_STM32_LRSP_CRC		(3 << 8)
+#define MCI_CPSM_STM32_ENABLE		BIT(12)
 
 #define MMCIRESPCMD		0x010
 #define MMCIRESPONSE0		0x014
@@ -130,6 +160,8 @@
 #define MCI_ST_SDIOIT		(1 << 22)
 #define MCI_ST_CEATAEND		(1 << 23)
 #define MCI_ST_CARDBUSY		(1 << 24)
+/* Extended status bits for the STM32 variants */
+#define MCI_STM32_BUSYD0	BIT(20)
 
 #define MMCICLEAR		0x038
 #define MCI_CMDCRCFAILCLR	(1 << 0)
@@ -175,11 +207,32 @@
 #define MCI_ST_SDIOITMASK	(1 << 22)
 #define MCI_ST_CEATAENDMASK	(1 << 23)
 #define MCI_ST_BUSYENDMASK	(1 << 24)
+/* Extended status bits for the STM32 variants */
+#define MCI_STM32_BUSYD0ENDMASK	BIT(21)
 
 #define MMCIMASK1		0x040
 #define MMCIFIFOCNT		0x048
 #define MMCIFIFO		0x080 /* to 0x0bc */
 
+/* STM32 sdmmc registers for IDMA (Internal DMA) */
+#define MMCI_STM32_IDMACTRLR	0x050
+#define MMCI_STM32_IDMAEN	BIT(0)
+#define MMCI_STM32_IDMALLIEN	BIT(1)
+
+#define MMCI_STM32_IDMABSIZER		0x054
+#define MMCI_STM32_IDMABNDT_SHIFT	5
+#define MMCI_STM32_IDMABNDT_MASK	GENMASK(12, 5)
+
+#define MMCI_STM32_IDMABASE0R	0x058
+
+#define MMCI_STM32_IDMALAR	0x64
+#define MMCI_STM32_IDMALA_MASK	GENMASK(13, 0)
+#define MMCI_STM32_ABR		BIT(29)
+#define MMCI_STM32_ULS		BIT(30)
+#define MMCI_STM32_ULA		BIT(31)
+
+#define MMCI_STM32_IDMABAR	0x68
+
 #define MCI_IRQENABLE	\
 	(MCI_CMDCRCFAILMASK | MCI_DATACRCFAILMASK | MCI_CMDTIMEOUTMASK | \
 	MCI_DATATIMEOUTMASK | MCI_TXUNDERRUNMASK | MCI_RXOVERRUNMASK |	\
@@ -190,6 +243,9 @@
 	(MCI_RXFIFOHALFFULLMASK | MCI_RXDATAAVLBLMASK | \
 	 MCI_TXFIFOHALFEMPTYMASK)
 
+#define MCI_IRQ_PIO_STM32_MASK \
+	(MCI_RXFIFOHALFFULLMASK | MCI_TXFIFOHALFEMPTYMASK)
+
 #define NR_SG		128
 
 #define MMCI_PINCTRL_STATE_OPENDRAIN "opendrain"
-- 
2.7.4

[PATCH V6 22/23] dt-bindings: mmci: add stm32 sdmmc variant

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds properties for stm32 sdmmc variant.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/mmc/mmci.txt | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt
index 4e69b25..6d3c626 100644
--- a/Documentation/devicetree/bindings/mmc/mmci.txt
+++ b/Documentation/devicetree/bindings/mmc/mmci.txt
@@ -16,8 +16,10 @@ Optional properties:
 - arm,primecell-periphid : contains the PrimeCell Peripheral ID, it overrides
                            the ID provided by the HW
 - resets                 : phandle to internal reset line.
+			   Should be defined for sdmmc variant.
 - vqmmc-supply           : phandle to the regulator device tree node, mentioned
                            as the VCCQ/VDD_IO supply in the eMMC/SD specs.
+specific for ux500 variant:
 - st,sig-dir-dat0        : bus signal direction pin used for DAT[0].
 - st,sig-dir-dat2        : bus signal direction pin used for DAT[2].
 - st,sig-dir-dat31       : bus signal direction pin used for DAT[3] and DAT[1].
@@ -25,6 +27,14 @@ Optional properties:
 - st,sig-dir-cmd         : cmd signal direction pin used for CMD.
 - st,sig-pin-fbclk       : feedback clock signal pin used.
 
+specific for sdmmc variant:
+- st,sig-dir             : signal direction polarity used for cmd, dat0 dat123.
+- st,neg-edge            : data & command phase relation, generated on
+                           sd clock falling edge.
+- st,use-ckin            : use ckin pin from an external driver to sample
+                           the receive data (example: with voltage
+			   switch transceiver).
+
 Deprecated properties:
 - mmc-cap-mmc-highspeed  : indicates whether MMC is high speed capable.
 - mmc-cap-sd-highspeed   : indicates whether SD is high speed capable.
-- 
2.7.4

[PATCH V6 23/23] mmc: mmci: add stm32 sdmmc variant

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds a stm32 sdmmc variant, rev 1.1.
Introduces a new Manufacturer id "0x53, ascii 'S' to define
new stm32 sdmmc family with clean range of amba
revision/configurations bits (corresponding to sdmmc_ver
register with major/minor fields).
Add 2 variants properties:
-dma_lli, to enable link list support.
-stm32_idmabsize_mask, defines the range of SDMMC_IDMABSIZER register
 which specify the number bytes per buffer.

DT properties for sdmmc:
-Indicate signal directions (only one property
 for d0dir, d123dir, cmd_dir)
-Select command and data phase relation.
-Select "clock in" from an external driver.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/Kconfig            |  10 ++
 drivers/mmc/host/Makefile           |   1 +
 drivers/mmc/host/mmci.c             |  36 +++++
 drivers/mmc/host/mmci.h             |   5 +
 drivers/mmc/host/mmci_stm32_sdmmc.c | 282 ++++++++++++++++++++++++++++++++++++
 5 files changed, 334 insertions(+)
 create mode 100644 drivers/mmc/host/mmci_stm32_sdmmc.c

diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 674ba43..9464e95 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -34,6 +34,16 @@ config MMC_QCOM_DML
 
 	  if unsure, say N.
 
+config MMC_STM32_SDMMC
+	bool "STMicroelectronics STM32 SDMMC Controller"
+	depends on MMC_ARMMMCI
+	default y
+	help
+	  This selects the STMicroelectronics STM32 SDMMC host controller.
+	  If you have a STM32 sdmmc host with internal dma say Y or M here.
+
+	  If unsure, say N.
+
 config MMC_PXA
 	tristate "Intel PXA25x/26x/27x Multimedia Card Interface support"
 	depends on ARCH_PXA
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index 5363d06..720d377 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -6,6 +6,7 @@
 obj-$(CONFIG_MMC_ARMMMCI) += armmmci.o
 armmmci-y := mmci.o
 armmmci-$(CONFIG_MMC_QCOM_DML) += mmci_qcom_dml.o
+armmmci-$(CONFIG_MMC_STM32_SDMMC) += mmci_stm32_sdmmc.o
 obj-$(CONFIG_MMC_PXA)		+= pxamci.o
 obj-$(CONFIG_MMC_MXC)		+= mxcmmc.o
 obj-$(CONFIG_MMC_MXS)		+= mxs-mmc.o
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index ad2f62f..82bab35 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -52,6 +52,12 @@ void mmci_variant_init(struct mmci_host *host);
 static inline void mmci_variant_init(struct mmci_host *host) {}
 #endif
 
+#ifdef CONFIG_MMC_STM32_SDMMC
+void sdmmc_variant_init(struct mmci_host *host);
+#else
+static inline void sdmmc_variant_init(struct mmci_host *host) {}
+#endif
+
 static unsigned int fmax = 515633;
 
 static struct variant_data variant_arm = {
@@ -259,6 +265,25 @@ static struct variant_data variant_stm32 = {
 	.init			= mmci_variant_init,
 };
 
+static struct variant_data variant_stm32_sdmmc = {
+	.fifosize		= 16 * 4,
+	.fifohalfsize		= 8 * 4,
+	.f_max			= 208000000,
+	.stm32_clkdiv		= true,
+	.cmdreg_cpsm_enable	= MCI_CPSM_STM32_ENABLE,
+	.cmdreg_lrsp_crc	= MCI_CPSM_STM32_LRSP_CRC,
+	.cmdreg_srsp_crc	= MCI_CPSM_STM32_SRSP_CRC,
+	.cmdreg_srsp		= MCI_CPSM_STM32_SRSP,
+	.data_cmd_enable	= MCI_CPSM_STM32_CMDTRANS,
+	.irq_pio_mask		= MCI_IRQ_PIO_STM32_MASK,
+	.datactrl_first		= true,
+	.datacnt_useless	= true,
+	.datalength_bits	= 25,
+	.datactrl_blocksz	= 14,
+	.stm32_idmabsize_mask	= GENMASK(12, 5),
+	.init			= sdmmc_variant_init,
+};
+
 static struct variant_data variant_qcom = {
 	.fifosize		= 16 * 4,
 	.fifohalfsize		= 8 * 4,
@@ -1736,6 +1761,12 @@ static int mmci_of_parse(struct device_node *np, struct mmc_host *mmc)
 		host->pwr_reg_add |= MCI_ST_CMDDIREN;
 	if (of_get_property(np, "st,sig-pin-fbclk", NULL))
 		host->pwr_reg_add |= MCI_ST_FBCLKEN;
+	if (of_get_property(np, "st,sig-dir", NULL))
+		host->pwr_reg_add |= MCI_STM32_DIRPOL;
+	if (of_get_property(np, "st,neg-edge", NULL))
+		host->clk_reg_add |= MCI_STM32_CLK_NEGEDGE;
+	if (of_get_property(np, "st,use-ckin", NULL))
+		host->clk_reg_add |= MCI_STM32_CLK_SELCKIN;
 
 	if (of_get_property(np, "mmc-cap-mmc-highspeed", NULL))
 		mmc->caps |= MMC_CAP_MMC_HIGHSPEED;
@@ -2177,6 +2208,11 @@ static const struct amba_id mmci_ids[] = {
 		.mask   = 0x00ffffff,
 		.data	= &variant_stm32,
 	},
+	{
+		.id     = 0x10153180,
+		.mask	= 0xf0ffffff,
+		.data	= &variant_stm32_sdmmc,
+	},
 	/* Qualcomm variants */
 	{
 		.id     = 0x00051180,
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index e242f44..550dd39 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -304,6 +304,8 @@ struct mmci_host;
  * @start_err: bitmask identifying the STARTBITERR bit inside MMCISTATUS
  *	       register.
  * @opendrain: bitmask identifying the OPENDRAIN bit inside MMCIPOWER register
+ * @dma_lli: true if variant has dma link list feature.
+ * @stm32_idmabsize_mask: stm32 sdmmc idma buffer size.
  */
 struct variant_data {
 	unsigned int		clkreg;
@@ -346,6 +348,8 @@ struct variant_data {
 	unsigned int		irq_pio_mask;
 	u32			start_err;
 	u32			opendrain;
+	u8			dma_lli:1;
+	u32			stm32_idmabsize_mask;
 	void (*init)(struct mmci_host *host);
 };
 
@@ -387,6 +391,7 @@ struct mmci_host {
 	u32			pwr_reg;
 	u32			pwr_reg_add;
 	u32			clk_reg;
+	u32			clk_reg_add;
 	u32			datactrl_reg;
 	u32			busy_status;
 	u32			mask1_reg;
diff --git a/drivers/mmc/host/mmci_stm32_sdmmc.c b/drivers/mmc/host/mmci_stm32_sdmmc.c
new file mode 100644
index 0000000..cfbfc6f
--- /dev/null
+++ b/drivers/mmc/host/mmci_stm32_sdmmc.c
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) STMicroelectronics 2018 - All Rights Reserved
+ * Author: Ludovic.barre@st.com for STMicroelectronics.
+ */
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
+#include <linux/reset.h>
+#include <linux/scatterlist.h>
+#include "mmci.h"
+
+#define SDMMC_LLI_BUF_LEN	PAGE_SIZE
+#define SDMMC_IDMA_BURST	BIT(MMCI_STM32_IDMABNDT_SHIFT)
+
+struct sdmmc_lli_desc {
+	u32 idmalar;
+	u32 idmabase;
+	u32 idmasize;
+};
+
+struct sdmmc_priv {
+	dma_addr_t sg_dma;
+	void *sg_cpu;
+};
+
+int sdmmc_idma_validate_data(struct mmci_host *host,
+			     struct mmc_data *data)
+{
+	struct scatterlist *sg;
+	int i;
+
+	/*
+	 * idma has constraints on idmabase & idmasize for each element
+	 * excepted the last element which has no constraint on idmasize
+	 */
+	for_each_sg(data->sg, sg, data->sg_len - 1, i) {
+		if (!IS_ALIGNED(sg_dma_address(data->sg), sizeof(u32)) ||
+		    !IS_ALIGNED(sg_dma_len(data->sg), SDMMC_IDMA_BURST)) {
+			dev_err(mmc_dev(host->mmc),
+				"unaligned scatterlist: ofst:%x length:%d\n",
+				data->sg->offset, data->sg->length);
+			return -EINVAL;
+		}
+	}
+
+	if (!IS_ALIGNED(sg_dma_address(data->sg), sizeof(u32))) {
+		dev_err(mmc_dev(host->mmc),
+			"unaligned last scatterlist: ofst:%x length:%d\n",
+			data->sg->offset, data->sg->length);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int _sdmmc_idma_prep_data(struct mmci_host *host,
+				 struct mmc_data *data)
+{
+	int n_elem;
+
+	n_elem = dma_map_sg(mmc_dev(host->mmc),
+			    data->sg,
+			    data->sg_len,
+			    mmc_get_dma_dir(data));
+
+	if (!n_elem) {
+		dev_err(mmc_dev(host->mmc), "dma_map_sg failed\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int sdmmc_idma_prep_data(struct mmci_host *host,
+				struct mmc_data *data, bool next)
+{
+	/* Check if job is already prepared. */
+	if (!next && data->host_cookie == host->next_cookie)
+		return 0;
+
+	return _sdmmc_idma_prep_data(host, data);
+}
+
+static void sdmmc_idma_unprep_data(struct mmci_host *host,
+				   struct mmc_data *data, int err)
+{
+	dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
+		     mmc_get_dma_dir(data));
+}
+
+static int sdmmc_idma_setup(struct mmci_host *host)
+{
+	struct sdmmc_priv *idma;
+
+	idma = devm_kzalloc(mmc_dev(host->mmc), sizeof(*idma), GFP_KERNEL);
+	if (!idma)
+		return -ENOMEM;
+
+	host->dma_priv = idma;
+
+	if (host->variant->dma_lli) {
+		idma->sg_cpu = dmam_alloc_coherent(mmc_dev(host->mmc),
+						   SDMMC_LLI_BUF_LEN,
+						   &idma->sg_dma, GFP_KERNEL);
+		if (!idma->sg_cpu) {
+			dev_err(mmc_dev(host->mmc),
+				"Failed to alloc IDMA descriptor\n");
+			return -ENOMEM;
+		}
+		host->mmc->max_segs = SDMMC_LLI_BUF_LEN /
+			sizeof(struct sdmmc_lli_desc);
+		host->mmc->max_seg_size = host->variant->stm32_idmabsize_mask;
+	} else {
+		host->mmc->max_segs = 1;
+		host->mmc->max_seg_size = host->mmc->max_req_size;
+	}
+
+	return 0;
+}
+
+static int sdmmc_idma_start(struct mmci_host *host, unsigned int *datactrl)
+
+{
+	struct sdmmc_priv *idma = host->dma_priv;
+	struct sdmmc_lli_desc *desc = (struct sdmmc_lli_desc *)idma->sg_cpu;
+	struct mmc_data *data = host->data;
+	struct scatterlist *sg;
+	int i;
+
+	if (!host->variant->dma_lli || data->sg_len == 1) {
+		writel_relaxed(sg_dma_address(data->sg),
+			       host->base + MMCI_STM32_IDMABASE0R);
+		writel_relaxed(MMCI_STM32_IDMAEN,
+			       host->base + MMCI_STM32_IDMACTRLR);
+		return 0;
+	}
+
+	for_each_sg(data->sg, sg, data->sg_len, i) {
+		desc[i].idmalar = (i + 1) * sizeof(struct sdmmc_lli_desc);
+		desc[i].idmalar |= MMCI_STM32_ULA | MMCI_STM32_ULS
+			| MMCI_STM32_ABR;
+		desc[i].idmabase = sg_dma_address(sg);
+		desc[i].idmasize = sg_dma_len(sg);
+	}
+
+	/* notice the end of link list */
+	desc[data->sg_len - 1].idmalar &= ~MMCI_STM32_ULA;
+
+	dma_wmb();
+	writel_relaxed(idma->sg_dma, host->base + MMCI_STM32_IDMABAR);
+	writel_relaxed(desc[0].idmalar, host->base + MMCI_STM32_IDMALAR);
+	writel_relaxed(desc[0].idmabase, host->base + MMCI_STM32_IDMABASE0R);
+	writel_relaxed(desc[0].idmasize, host->base + MMCI_STM32_IDMABSIZER);
+	writel_relaxed(MMCI_STM32_IDMAEN | MMCI_STM32_IDMALLIEN,
+		       host->base + MMCI_STM32_IDMACTRLR);
+
+	return 0;
+}
+
+static void sdmmc_idma_finalize(struct mmci_host *host, struct mmc_data *data)
+{
+	writel_relaxed(0, host->base + MMCI_STM32_IDMACTRLR);
+}
+
+static void mmci_sdmmc_set_clkreg(struct mmci_host *host, unsigned int desired)
+{
+	unsigned int clk = 0, ddr = 0;
+
+	if (host->mmc->ios.timing == MMC_TIMING_MMC_DDR52 ||
+	    host->mmc->ios.timing == MMC_TIMING_UHS_DDR50)
+		ddr = MCI_STM32_CLK_DDR;
+
+	/*
+	 * cclk = mclk / (2 * clkdiv)
+	 * clkdiv 0 => bypass
+	 * in ddr mode bypass is not possible
+	 */
+	if (desired) {
+		if (desired >= host->mclk && !ddr) {
+			host->cclk = host->mclk;
+		} else {
+			clk = DIV_ROUND_UP(host->mclk, 2 * desired);
+			if (clk > MCI_STM32_CLK_CLKDIV_MSK)
+				clk = MCI_STM32_CLK_CLKDIV_MSK;
+			host->cclk = host->mclk / (2 * clk);
+		}
+	} else {
+		/*
+		 * while power-on phase the clock can't be define to 0,
+		 * Only power-off and power-cyc deactivate the clock.
+		 * if desired clock is 0, set max divider
+		 */
+		clk = MCI_STM32_CLK_CLKDIV_MSK;
+		host->cclk = host->mclk / (2 * clk);
+	}
+
+	/* Set actual clock for debug */
+	if (host->mmc->ios.power_mode == MMC_POWER_ON)
+		host->mmc->actual_clock = host->cclk;
+	else
+		host->mmc->actual_clock = 0;
+
+	if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4)
+		clk |= MCI_STM32_CLK_WIDEBUS_4;
+	if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8)
+		clk |= MCI_STM32_CLK_WIDEBUS_8;
+
+	clk |= MCI_STM32_CLK_HWFCEN;
+	clk |= host->clk_reg_add;
+	clk |= ddr;
+
+	/*
+	 * SDMMC_FBCK is selected when an external Delay Block is needed
+	 * with SDR104.
+	 */
+	if (host->mmc->ios.timing >= MMC_TIMING_UHS_SDR50) {
+		clk |= MCI_STM32_CLK_BUSSPEED;
+		if (host->mmc->ios.timing == MMC_TIMING_UHS_SDR104) {
+			clk &= ~MCI_STM32_CLK_SEL_MSK;
+			clk |= MCI_STM32_CLK_SELFBCK;
+		}
+	}
+
+	mmci_write_clkreg(host, clk);
+}
+
+static void mmci_sdmmc_set_pwrreg(struct mmci_host *host, unsigned int pwr)
+{
+	struct mmc_ios ios = host->mmc->ios;
+
+	pwr = host->pwr_reg_add;
+
+	if (ios.power_mode == MMC_POWER_OFF) {
+		/* Only a reset could power-off sdmmc */
+		reset_control_assert(host->rst);
+		udelay(2);
+		reset_control_deassert(host->rst);
+
+		/*
+		 * Set the SDMMC in Power-cycle state.
+		 * This will make that the SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK
+		 * are driven low, to prevent the Card from being supplied
+		 * through the signal lines.
+		 */
+		mmci_write_pwrreg(host, MCI_STM32_PWR_CYC | pwr);
+	} else if (ios.power_mode == MMC_POWER_ON) {
+		/*
+		 * After power-off (reset): the irq mask defined in probe
+		 * functionis lost
+		 * ault irq mask (probe) must be activated
+		 */
+		writel(MCI_IRQENABLE | host->variant->start_err,
+		       host->base + MMCIMASK0);
+
+		/*
+		 * After a power-cycle state, we must set the SDMMC in
+		 * Power-off. The SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are
+		 * driven high. Then we can set the SDMMC to Power-on state
+		 */
+		mmci_write_pwrreg(host, MCI_PWR_OFF | pwr);
+		mdelay(1);
+		mmci_write_pwrreg(host, MCI_PWR_ON | pwr);
+	}
+}
+
+static struct mmci_host_ops sdmmc_variant_ops = {
+	.validate_data = sdmmc_idma_validate_data,
+	.prep_data = sdmmc_idma_prep_data,
+	.unprep_data = sdmmc_idma_unprep_data,
+	.dma_setup = sdmmc_idma_setup,
+	.dma_start = sdmmc_idma_start,
+	.dma_finalize = sdmmc_idma_finalize,
+	.set_clkreg = mmci_sdmmc_set_clkreg,
+	.set_pwrreg = mmci_sdmmc_set_pwrreg,
+};
+
+void sdmmc_variant_init(struct mmci_host *host)
+{
+	host->ops = &sdmmc_variant_ops;
+}
-- 
2.7.4

Re: [PATCH V6 00/23] mmc: mmci: add sdmmc variant for stm32

[Ulf Hansson]

On 8 October 2018 at 14:08, Ludovic Barre <ludovic.Barre@st.com> wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
>
> The goal of this serie is to add support of sdmmc for stm32.
> Be to able to add this new variant it is needed to do some changes in
> mmci core:
> -Internalize specific needs of legacy dmaengine.
> -Create and setup dma_priv pointer.
> -Create generic callbacks which share some features (like cookie...)
>  and call specific needs.
>
> change v6:
> -move mmci_variant_init in mmci.c
> -dma_setup/release: let the variants clean up themselves.
>
> change v5:
> -error management in mmci_dmae_setup and qcom_dma_setup
>  mmci_dmae_setup: fail when tx & rx are not defined.
>  qcom_dma_setup: faill if one of channels is not defined.
> -define mmci_variant_init following CONFIG_DMA_ENGINE state.
> -squash dma_setup/dma_release callback.
>
> change v4:
> -checkpatch fix bool to u8
> -add use_dma variable to fallback to pio mode
> -move to optional reset with dt binding note for sdmmc
> -separate patch for DT doc
>
> change v3:
> -remove __dma_inprogress rename
> -remove bad space at end of "st,use-ckin"
>
> change v2:
> -rename to mmci_prep/unprep_data
> -rename specific dma engine structure to mmci_dmae_next/priv
> -follow "_" recommandation
> -remove dma prefixe of mmci_dmae_priv fields
>
> Ludovic Barre (23):
>   mmc: mmci: create common mmci_dma_setup/release
>   mmc: mmci: introduce dma_priv pointer to mmci_host
>   mmc: mmci: merge prepare data functions
>   mmc: mmci: add prepare/unprepare_data callbacks
>   mmc: mmci: add get_next_data callback
>   mmc: mmci: add dma_start callback
>   mmc: mmci: add dma_finalize callback
>   mmc: mmci: add dma_error callback
>   mmc: mmci: add validate_data callback
>   mmc: mmci: add set_clk/pwrreg callbacks
>   mmc: mmci: add datactrl block size variant property
>   mmc: mmci: expand startbiterr to irqmask and error check
>   mmc: mmci: add variant properties to define cpsm & cmdresp bits
>   mmc: mmci: add variant property to define dpsm bit
>   mmc: mmci: add variant property to define irq pio mask
>   mmc: mmci: add variant property to write datactrl before command
>   mmc: mmci: add variant property to not read datacnt
>   dt-bindings: mmci: add optional reset property
>   mmc: mmci: add optional reset property
>   mmc: mmci: add clock divider for stm32 sdmmc
>   mmc: mmci: add stm32 sdmmc registers
>   dt-bindings: mmci: add stm32 sdmmc variant
>   mmc: mmci: add stm32 sdmmc variant
>
>  Documentation/devicetree/bindings/mmc/mmci.txt |  11 +
>  drivers/mmc/host/Kconfig                       |  10 +
>  drivers/mmc/host/Makefile                      |   1 +
>  drivers/mmc/host/mmci.c                        | 628 ++++++++++++++++++-------
>  drivers/mmc/host/mmci.h                        | 140 +++++-
>  drivers/mmc/host/mmci_qcom_dml.c               |  17 +-
>  drivers/mmc/host/mmci_stm32_sdmmc.c            | 282 +++++++++++
>  7 files changed, 886 insertions(+), 203 deletions(-)
>  create mode 100644 drivers/mmc/host/mmci_stm32_sdmmc.c
>
> --
> 2.7.4
>

Applied for next, thanks!

FYI, I made little fixup of the help text in the Kconfig for the last patch.

Kind regards
Uffe

Re: [PATCH V6 00/23] mmc: mmci: add sdmmc variant for stm32

[Ludovic BARRE]

hi Ulf

On 10/09/2018 09:30 AM, Ulf Hansson wrote:
> Applied for next, thanks!
> 
> FYI, I made little fixup of the help text in the Kconfig for the last patch.

Thanks for your review.
Did you had a feedback on Qcom platform tests?

> 
> Kind regards
> Uffe

Re: [PATCH V6 00/23] mmc: mmci: add sdmmc variant for stm32

[Ulf Hansson]

On 9 October 2018 at 09:54, Ludovic BARRE <ludovic.barre@st.com> wrote:
> hi Ulf
>
> On 10/09/2018 09:30 AM, Ulf Hansson wrote:
>>
>> Applied for next, thanks!
>>
>> FYI, I made little fixup of the help text in the Kconfig for the last
>> patch.
>
>
> Thanks for your review.
> Did you had a feedback on Qcom platform tests?

Nope. I am leaving the tests for Qcom platforms to be done by
kernelci, let's see what the reports are.

Kind regards
Uffe

Re: [PATCH V6 00/23] mmc: mmci: add sdmmc variant for stm32

[Ulf Hansson]

On 9 October 2018 at 13:18, Ulf Hansson <ulf.hansson@linaro.org> wrote:
> On 9 October 2018 at 09:54, Ludovic BARRE <ludovic.barre@st.com> wrote:
>> hi Ulf
>>
>> On 10/09/2018 09:30 AM, Ulf Hansson wrote:
>>>
>>> Applied for next, thanks!
>>>
>>> FYI, I made little fixup of the help text in the Kconfig for the last
>>> patch.
>>
>>
>> Thanks for your review.
>> Did you had a feedback on Qcom platform tests?
>
> Nope. I am leaving the tests for Qcom platforms to be done by
> kernelci, let's see what the reports are.

FYI:

https://kernelci.org/boot/id/5bbdcd2b59b5147001b435a4/

Looks good!

Kind regards
Uffe

Re: [PATCH V6 00/23] mmc: mmci: add sdmmc variant for stm32

[Ludovic BARRE]

hi Ulf

On 10/11/2018 12:33 PM, Ulf Hansson wrote:
> On 9 October 2018 at 13:18, Ulf Hansson <ulf.hansson@linaro.org> wrote:
>> On 9 October 2018 at 09:54, Ludovic BARRE <ludovic.barre@st.com> wrote:
>>> hi Ulf
>>>
>>> On 10/09/2018 09:30 AM, Ulf Hansson wrote:
>>>>
>>>> Applied for next, thanks!
>>>>
>>>> FYI, I made little fixup of the help text in the Kconfig for the last
>>>> patch.
>>>
>>>
>>> Thanks for your review.
>>> Did you had a feedback on Qcom platform tests?
>>
>> Nope. I am leaving the tests for Qcom platforms to be done by
>> kernelci, let's see what the reports are.
> 
> FYI:
> 
> https://kernelci.org/boot/id/5bbdcd2b59b5147001b435a4/
> 
> Looks good!

Thanks for the boot tests on qcom

BR
Ludo

> 
> Kind regards
> Uffe
>