* [PATCH v2 0/6] add i2c support for mt7629 and mt8183
@ 2018-12-21 12:58 qii wang
2018-12-21 12:58 ` [PATCH 1/6] dt-bindings: i2c: Add Mediatek MT7629 i2c binding qii wang
` (5 more replies)
0 siblings, 6 replies; 11+ messages in thread
From: qii wang @ 2018-12-21 12:58 UTC (permalink / raw)
To: wsa
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
linux-mediatek, srv_heupstream, leilk.liu, qii.wang, ryder.lee
This series are based on 4.20-rc1 and provide five patches to support
mt7629 and mt8183 IC.
Main changes compared to v1:
--remove useless dt-binding for mt7629
--split a patch into two(2/6 3/6)
--muti-user feature was dropped
qii wang (6):
dt-bindings: i2c: Add Mediatek MT7629 i2c binding
i2c: mediatek: speeds is replaced by macros definitions
i2c: mediatek: remove completion_done()
i2c: mediatek: Add offsets array for new i2c registers
dt-bindings: i2c: Add Mediatek MT8183 i2c binding
i2c: mediatek: Add i2c support for MediaTek MT8183
Documentation/devicetree/bindings/i2c/i2c-mtk.txt | 7 +-
drivers/i2c/busses/i2c-mt65xx.c | 288 ++++++++++++++++-----
2 files changed, 227 insertions(+), 68 deletions(-)
--
1.7.9.5
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH 1/6] dt-bindings: i2c: Add Mediatek MT7629 i2c binding
2018-12-21 12:58 [PATCH v2 0/6] add i2c support for mt7629 and mt8183 qii wang
@ 2018-12-21 12:58 ` qii wang
2019-01-03 19:21 ` Rob Herring
2018-12-21 12:58 ` [PATCH 2/6] i2c: mediatek: speeds is replaced by macros definitions qii wang
` (4 subsequent siblings)
5 siblings, 1 reply; 11+ messages in thread
From: qii wang @ 2018-12-21 12:58 UTC (permalink / raw)
To: wsa
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
linux-mediatek, srv_heupstream, leilk.liu, qii.wang, ryder.lee
Add MT7629 i2c binding to binding file.
Signed-off-by: qii wang <qii.wang@mediatek.com>
---
Documentation/devicetree/bindings/i2c/i2c-mtk.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt
index e199695..ee4c324 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt
@@ -10,6 +10,7 @@ Required properties:
"mediatek,mt6589-i2c": for MediaTek MT6589
"mediatek,mt7622-i2c": for MediaTek MT7622
"mediatek,mt7623-i2c", "mediatek,mt6577-i2c": for MediaTek MT7623
+ "mediatek,mt7629-i2c", "mediatek,mt2712-i2c": for MediaTek MT7629
"mediatek,mt8173-i2c": for MediaTek MT8173
- reg: physical base address of the controller and dma base, length of memory
mapped region.
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 2/6] i2c: mediatek: speeds is replaced by macros definitions
2018-12-21 12:58 [PATCH v2 0/6] add i2c support for mt7629 and mt8183 qii wang
2018-12-21 12:58 ` [PATCH 1/6] dt-bindings: i2c: Add Mediatek MT7629 i2c binding qii wang
@ 2018-12-21 12:58 ` qii wang
2018-12-25 11:51 ` Nicolas Boichat
2018-12-21 12:58 ` [PATCH 3/6] i2c: mediatek: remove completion_done() qii wang
` (3 subsequent siblings)
5 siblings, 1 reply; 11+ messages in thread
From: qii wang @ 2018-12-21 12:58 UTC (permalink / raw)
To: wsa
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
linux-mediatek, srv_heupstream, leilk.liu, qii.wang, ryder.lee
Different speeds have been defined by macros,
so we use macros definitions.
Signed-off-by: qii wang <qii.wang@mediatek.com>
---
drivers/i2c/busses/i2c-mt65xx.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/i2c/busses/i2c-mt65xx.c b/drivers/i2c/busses/i2c-mt65xx.c
index a74ef76..7396449 100644
--- a/drivers/i2c/busses/i2c-mt65xx.c
+++ b/drivers/i2c/busses/i2c-mt65xx.c
@@ -456,7 +456,7 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
control_reg = readw(i2c->base + OFFSET_CONTROL) &
~(I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS);
- if ((i2c->speed_hz > 400000) || (left_num >= 1))
+ if ((i2c->speed_hz > MAX_FS_MODE_SPEED) || (left_num >= 1))
control_reg |= I2C_CONTROL_RS;
if (i2c->op == I2C_MASTER_WRRD)
@@ -465,7 +465,7 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
writew(control_reg, i2c->base + OFFSET_CONTROL);
/* set start condition */
- if (i2c->speed_hz <= 100000)
+ if (i2c->speed_hz <= I2C_DEFAULT_SPEED)
writew(I2C_ST_START_CON, i2c->base + OFFSET_EXT_CONF);
else
writew(I2C_FS_START_CON, i2c->base + OFFSET_EXT_CONF);
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 3/6] i2c: mediatek: remove completion_done()
2018-12-21 12:58 [PATCH v2 0/6] add i2c support for mt7629 and mt8183 qii wang
2018-12-21 12:58 ` [PATCH 1/6] dt-bindings: i2c: Add Mediatek MT7629 i2c binding qii wang
2018-12-21 12:58 ` [PATCH 2/6] i2c: mediatek: speeds is replaced by macros definitions qii wang
@ 2018-12-21 12:58 ` qii wang
2018-12-21 12:58 ` [PATCH 4/6] i2c: mediatek: Add offsets array for new i2c registers qii wang
` (2 subsequent siblings)
5 siblings, 0 replies; 11+ messages in thread
From: qii wang @ 2018-12-21 12:58 UTC (permalink / raw)
To: wsa
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
linux-mediatek, srv_heupstream, leilk.liu, qii.wang, ryder.lee
Completion_done() is useless when we don't use its return value,
so we remove it.
Signed-off-by: qii wang <qii.wang@mediatek.com>
---
drivers/i2c/busses/i2c-mt65xx.c | 2 --
1 file changed, 2 deletions(-)
diff --git a/drivers/i2c/busses/i2c-mt65xx.c b/drivers/i2c/busses/i2c-mt65xx.c
index 7396449..660de1e 100644
--- a/drivers/i2c/busses/i2c-mt65xx.c
+++ b/drivers/i2c/busses/i2c-mt65xx.c
@@ -642,8 +642,6 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
return -ETIMEDOUT;
}
- completion_done(&i2c->msg_complete);
-
if (i2c->irq_stat & (I2C_HS_NACKERR | I2C_ACKERR)) {
dev_dbg(i2c->dev, "addr: %x, transfer ACK error\n", msgs->addr);
mtk_i2c_init_hw(i2c);
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 4/6] i2c: mediatek: Add offsets array for new i2c registers
2018-12-21 12:58 [PATCH v2 0/6] add i2c support for mt7629 and mt8183 qii wang
` (2 preceding siblings ...)
2018-12-21 12:58 ` [PATCH 3/6] i2c: mediatek: remove completion_done() qii wang
@ 2018-12-21 12:58 ` qii wang
2018-12-25 11:49 ` Nicolas Boichat
2018-12-21 12:58 ` [PATCH 5/6] dt-bindings: i2c: Add Mediatek MT8183 i2c binding qii wang
2018-12-21 12:58 ` [PATCH 6/6] i2c: mediatek: Add i2c support for MediaTek MT8183 qii wang
5 siblings, 1 reply; 11+ messages in thread
From: qii wang @ 2018-12-21 12:58 UTC (permalink / raw)
To: wsa
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
linux-mediatek, srv_heupstream, leilk.liu, qii.wang, ryder.lee
New i2c registers would have different offsets, so we use different
offsets array to distinguish different i2c registers version.
Signed-off-by: qii wang <qii.wang@mediatek.com>
---
drivers/i2c/busses/i2c-mt65xx.c | 163 +++++++++++++++++++++++++--------------
1 file changed, 104 insertions(+), 59 deletions(-)
diff --git a/drivers/i2c/busses/i2c-mt65xx.c b/drivers/i2c/busses/i2c-mt65xx.c
index 660de1e..428ac99 100644
--- a/drivers/i2c/busses/i2c-mt65xx.c
+++ b/drivers/i2c/busses/i2c-mt65xx.c
@@ -106,34 +106,62 @@ enum mtk_trans_op {
};
enum I2C_REGS_OFFSET {
- OFFSET_DATA_PORT = 0x0,
- OFFSET_SLAVE_ADDR = 0x04,
- OFFSET_INTR_MASK = 0x08,
- OFFSET_INTR_STAT = 0x0c,
- OFFSET_CONTROL = 0x10,
- OFFSET_TRANSFER_LEN = 0x14,
- OFFSET_TRANSAC_LEN = 0x18,
- OFFSET_DELAY_LEN = 0x1c,
- OFFSET_TIMING = 0x20,
- OFFSET_START = 0x24,
- OFFSET_EXT_CONF = 0x28,
- OFFSET_FIFO_STAT = 0x30,
- OFFSET_FIFO_THRESH = 0x34,
- OFFSET_FIFO_ADDR_CLR = 0x38,
- OFFSET_IO_CONFIG = 0x40,
- OFFSET_RSV_DEBUG = 0x44,
- OFFSET_HS = 0x48,
- OFFSET_SOFTRESET = 0x50,
- OFFSET_DCM_EN = 0x54,
- OFFSET_PATH_DIR = 0x60,
- OFFSET_DEBUGSTAT = 0x64,
- OFFSET_DEBUGCTRL = 0x68,
- OFFSET_TRANSFER_LEN_AUX = 0x6c,
- OFFSET_CLOCK_DIV = 0x70,
+ OFFSET_DATA_PORT,
+ OFFSET_SLAVE_ADDR,
+ OFFSET_INTR_MASK,
+ OFFSET_INTR_STAT,
+ OFFSET_CONTROL,
+ OFFSET_TRANSFER_LEN,
+ OFFSET_TRANSAC_LEN,
+ OFFSET_DELAY_LEN,
+ OFFSET_TIMING,
+ OFFSET_START,
+ OFFSET_EXT_CONF,
+ OFFSET_FIFO_STAT,
+ OFFSET_FIFO_THRESH,
+ OFFSET_FIFO_ADDR_CLR,
+ OFFSET_IO_CONFIG,
+ OFFSET_RSV_DEBUG,
+ OFFSET_HS,
+ OFFSET_SOFTRESET,
+ OFFSET_DCM_EN,
+ OFFSET_PATH_DIR,
+ OFFSET_DEBUGSTAT,
+ OFFSET_DEBUGCTRL,
+ OFFSET_TRANSFER_LEN_AUX,
+ OFFSET_CLOCK_DIV,
+};
+
+static const u16 mt_i2c_regs_v1[] = {
+ [OFFSET_DATA_PORT] = 0x0,
+ [OFFSET_SLAVE_ADDR] = 0x4,
+ [OFFSET_INTR_MASK] = 0x8,
+ [OFFSET_INTR_STAT] = 0xc,
+ [OFFSET_CONTROL] = 0x10,
+ [OFFSET_TRANSFER_LEN] = 0x14,
+ [OFFSET_TRANSAC_LEN] = 0x18,
+ [OFFSET_DELAY_LEN] = 0x1c,
+ [OFFSET_TIMING] = 0x20,
+ [OFFSET_START] = 0x24,
+ [OFFSET_EXT_CONF] = 0x28,
+ [OFFSET_FIFO_STAT] = 0x30,
+ [OFFSET_FIFO_THRESH] = 0x34,
+ [OFFSET_FIFO_ADDR_CLR] = 0x38,
+ [OFFSET_IO_CONFIG] = 0x40,
+ [OFFSET_RSV_DEBUG] = 0x44,
+ [OFFSET_HS] = 0x48,
+ [OFFSET_SOFTRESET] = 0x50,
+ [OFFSET_DCM_EN] = 0x54,
+ [OFFSET_PATH_DIR] = 0x60,
+ [OFFSET_DEBUGSTAT] = 0x64,
+ [OFFSET_DEBUGCTRL] = 0x68,
+ [OFFSET_TRANSFER_LEN_AUX] = 0x6c,
+ [OFFSET_CLOCK_DIV] = 0x70,
};
struct mtk_i2c_compatible {
const struct i2c_adapter_quirks *quirks;
+ const u16 *regs;
unsigned char pmic_i2c: 1;
unsigned char dcm: 1;
unsigned char auto_restart: 1;
@@ -181,6 +209,7 @@ struct mtk_i2c {
};
static const struct mtk_i2c_compatible mt2712_compat = {
+ .regs = mt_i2c_regs_v1,
.pmic_i2c = 0,
.dcm = 1,
.auto_restart = 1,
@@ -191,6 +220,7 @@ struct mtk_i2c {
static const struct mtk_i2c_compatible mt6577_compat = {
.quirks = &mt6577_i2c_quirks,
+ .regs = mt_i2c_regs_v1,
.pmic_i2c = 0,
.dcm = 1,
.auto_restart = 0,
@@ -201,6 +231,7 @@ struct mtk_i2c {
static const struct mtk_i2c_compatible mt6589_compat = {
.quirks = &mt6577_i2c_quirks,
+ .regs = mt_i2c_regs_v1,
.pmic_i2c = 1,
.dcm = 0,
.auto_restart = 0,
@@ -211,6 +242,7 @@ struct mtk_i2c {
static const struct mtk_i2c_compatible mt7622_compat = {
.quirks = &mt7622_i2c_quirks,
+ .regs = mt_i2c_regs_v1,
.pmic_i2c = 0,
.dcm = 1,
.auto_restart = 1,
@@ -220,6 +252,7 @@ struct mtk_i2c {
};
static const struct mtk_i2c_compatible mt8173_compat = {
+ .regs = mt_i2c_regs_v1,
.pmic_i2c = 0,
.dcm = 1,
.auto_restart = 1,
@@ -238,6 +271,17 @@ struct mtk_i2c {
};
MODULE_DEVICE_TABLE(of, mtk_i2c_of_match);
+static u16 mtk_i2c_readw(struct mtk_i2c *i2c, enum I2C_REGS_OFFSET reg)
+{
+ return readw(i2c->base + i2c->dev_comp->regs[reg]);
+}
+
+static void mtk_i2c_writew(struct mtk_i2c *i2c, u16 val,
+ enum I2C_REGS_OFFSET reg)
+{
+ writew(val, i2c->base + i2c->dev_comp->regs[reg]);
+}
+
static int mtk_i2c_clock_enable(struct mtk_i2c *i2c)
{
int ret;
@@ -278,31 +322,31 @@ static void mtk_i2c_init_hw(struct mtk_i2c *i2c)
{
u16 control_reg;
- writew(I2C_SOFT_RST, i2c->base + OFFSET_SOFTRESET);
+ mtk_i2c_writew(i2c, I2C_SOFT_RST, OFFSET_SOFTRESET);
/* Set ioconfig */
if (i2c->use_push_pull)
- writew(I2C_IO_CONFIG_PUSH_PULL, i2c->base + OFFSET_IO_CONFIG);
+ mtk_i2c_writew(i2c, I2C_IO_CONFIG_PUSH_PULL, OFFSET_IO_CONFIG);
else
- writew(I2C_IO_CONFIG_OPEN_DRAIN, i2c->base + OFFSET_IO_CONFIG);
+ mtk_i2c_writew(i2c, I2C_IO_CONFIG_OPEN_DRAIN, OFFSET_IO_CONFIG);
if (i2c->dev_comp->dcm)
- writew(I2C_DCM_DISABLE, i2c->base + OFFSET_DCM_EN);
+ mtk_i2c_writew(i2c, I2C_DCM_DISABLE, OFFSET_DCM_EN);
if (i2c->dev_comp->timing_adjust)
- writew(I2C_DEFAULT_CLK_DIV - 1, i2c->base + OFFSET_CLOCK_DIV);
+ mtk_i2c_writew(i2c, I2C_DEFAULT_CLK_DIV - 1, OFFSET_CLOCK_DIV);
- writew(i2c->timing_reg, i2c->base + OFFSET_TIMING);
- writew(i2c->high_speed_reg, i2c->base + OFFSET_HS);
+ mtk_i2c_writew(i2c, i2c->timing_reg, OFFSET_TIMING);
+ mtk_i2c_writew(i2c, i2c->high_speed_reg, OFFSET_HS);
/* If use i2c pin from PMIC mt6397 side, need set PATH_DIR first */
if (i2c->have_pmic)
- writew(I2C_CONTROL_WRAPPER, i2c->base + OFFSET_PATH_DIR);
+ mtk_i2c_writew(i2c, I2C_CONTROL_WRAPPER, OFFSET_PATH_DIR);
control_reg = I2C_CONTROL_ACKERR_DET_EN |
I2C_CONTROL_CLK_EXT_EN | I2C_CONTROL_DMA_EN;
- writew(control_reg, i2c->base + OFFSET_CONTROL);
- writew(I2C_DELAY_LEN, i2c->base + OFFSET_DELAY_LEN);
+ mtk_i2c_writew(i2c, control_reg, OFFSET_CONTROL);
+ mtk_i2c_writew(i2c, I2C_DELAY_LEN, OFFSET_DELAY_LEN);
writel(I2C_DMA_HARD_RST, i2c->pdmabase + OFFSET_RST);
udelay(50);
@@ -454,7 +498,7 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
reinit_completion(&i2c->msg_complete);
- control_reg = readw(i2c->base + OFFSET_CONTROL) &
+ control_reg = mtk_i2c_readw(i2c, OFFSET_CONTROL) &
~(I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS);
if ((i2c->speed_hz > MAX_FS_MODE_SPEED) || (left_num >= 1))
control_reg |= I2C_CONTROL_RS;
@@ -462,40 +506,41 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
if (i2c->op == I2C_MASTER_WRRD)
control_reg |= I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS;
- writew(control_reg, i2c->base + OFFSET_CONTROL);
+ mtk_i2c_writew(i2c, control_reg, OFFSET_CONTROL);
/* set start condition */
if (i2c->speed_hz <= I2C_DEFAULT_SPEED)
- writew(I2C_ST_START_CON, i2c->base + OFFSET_EXT_CONF);
+ mtk_i2c_writew(i2c, I2C_ST_START_CON, OFFSET_EXT_CONF);
else
- writew(I2C_FS_START_CON, i2c->base + OFFSET_EXT_CONF);
+ mtk_i2c_writew(i2c, I2C_FS_START_CON, OFFSET_EXT_CONF);
addr_reg = i2c_8bit_addr_from_msg(msgs);
- writew(addr_reg, i2c->base + OFFSET_SLAVE_ADDR);
+ mtk_i2c_writew(i2c, addr_reg, OFFSET_SLAVE_ADDR);
/* Clear interrupt status */
- writew(restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
- I2C_TRANSAC_COMP, i2c->base + OFFSET_INTR_STAT);
- writew(I2C_FIFO_ADDR_CLR, i2c->base + OFFSET_FIFO_ADDR_CLR);
+ mtk_i2c_writew(i2c, restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
+ I2C_TRANSAC_COMP, OFFSET_INTR_STAT);
+
+ mtk_i2c_writew(i2c, I2C_FIFO_ADDR_CLR, OFFSET_FIFO_ADDR_CLR);
/* Enable interrupt */
- writew(restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
- I2C_TRANSAC_COMP, i2c->base + OFFSET_INTR_MASK);
+ mtk_i2c_writew(i2c, restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
+ I2C_TRANSAC_COMP, OFFSET_INTR_MASK);
/* Set transfer and transaction len */
if (i2c->op == I2C_MASTER_WRRD) {
if (i2c->dev_comp->aux_len_reg) {
- writew(msgs->len, i2c->base + OFFSET_TRANSFER_LEN);
- writew((msgs + 1)->len, i2c->base +
- OFFSET_TRANSFER_LEN_AUX);
+ mtk_i2c_writew(i2c, msgs->len, OFFSET_TRANSFER_LEN);
+ mtk_i2c_writew(i2c, (msgs + 1)->len,
+ OFFSET_TRANSFER_LEN_AUX);
} else {
- writew(msgs->len | ((msgs + 1)->len) << 8,
- i2c->base + OFFSET_TRANSFER_LEN);
+ mtk_i2c_writew(i2c, msgs->len | ((msgs + 1)->len) << 8,
+ OFFSET_TRANSFER_LEN);
}
- writew(I2C_WRRD_TRANAC_VALUE, i2c->base + OFFSET_TRANSAC_LEN);
+ mtk_i2c_writew(i2c, I2C_WRRD_TRANAC_VALUE, OFFSET_TRANSAC_LEN);
} else {
- writew(msgs->len, i2c->base + OFFSET_TRANSFER_LEN);
- writew(num, i2c->base + OFFSET_TRANSAC_LEN);
+ mtk_i2c_writew(i2c, msgs->len, OFFSET_TRANSFER_LEN);
+ mtk_i2c_writew(i2c, num, OFFSET_TRANSAC_LEN);
}
/* Prepare buffer data to start transfer */
@@ -607,14 +652,14 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
if (left_num >= 1)
start_reg |= I2C_RS_MUL_CNFG;
}
- writew(start_reg, i2c->base + OFFSET_START);
+ mtk_i2c_writew(i2c, start_reg, OFFSET_START);
ret = wait_for_completion_timeout(&i2c->msg_complete,
i2c->adap.timeout);
/* Clear interrupt mask */
- writew(~(restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
- I2C_TRANSAC_COMP), i2c->base + OFFSET_INTR_MASK);
+ mtk_i2c_writew(i2c, ~(restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
+ I2C_TRANSAC_COMP), OFFSET_INTR_MASK);
if (i2c->op == I2C_MASTER_WR) {
dma_unmap_single(i2c->dev, wpaddr,
@@ -724,8 +769,8 @@ static irqreturn_t mtk_i2c_irq(int irqno, void *dev_id)
if (i2c->auto_restart)
restart_flag = I2C_RS_TRANSFER;
- intr_stat = readw(i2c->base + OFFSET_INTR_STAT);
- writew(intr_stat, i2c->base + OFFSET_INTR_STAT);
+ intr_stat = mtk_i2c_readw(i2c, OFFSET_INTR_STAT);
+ mtk_i2c_writew(i2c, intr_stat, OFFSET_INTR_STAT);
/*
* when occurs ack error, i2c controller generate two interrupts
@@ -737,8 +782,8 @@ static irqreturn_t mtk_i2c_irq(int irqno, void *dev_id)
if (i2c->ignore_restart_irq && (i2c->irq_stat & restart_flag)) {
i2c->ignore_restart_irq = false;
i2c->irq_stat = 0;
- writew(I2C_RS_MUL_CNFG | I2C_RS_MUL_TRIG | I2C_TRANSAC_START,
- i2c->base + OFFSET_START);
+ mtk_i2c_writew(i2c, I2C_RS_MUL_CNFG | I2C_RS_MUL_TRIG |
+ I2C_TRANSAC_START, OFFSET_START);
} else {
if (i2c->irq_stat & (I2C_TRANSAC_COMP | restart_flag))
complete(&i2c->msg_complete);
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 5/6] dt-bindings: i2c: Add Mediatek MT8183 i2c binding
2018-12-21 12:58 [PATCH v2 0/6] add i2c support for mt7629 and mt8183 qii wang
` (3 preceding siblings ...)
2018-12-21 12:58 ` [PATCH 4/6] i2c: mediatek: Add offsets array for new i2c registers qii wang
@ 2018-12-21 12:58 ` qii wang
2019-01-03 19:23 ` Rob Herring
2018-12-21 12:58 ` [PATCH 6/6] i2c: mediatek: Add i2c support for MediaTek MT8183 qii wang
5 siblings, 1 reply; 11+ messages in thread
From: qii wang @ 2018-12-21 12:58 UTC (permalink / raw)
To: wsa
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
linux-mediatek, srv_heupstream, leilk.liu, qii.wang, ryder.lee
Add MT8183 i2c binding to binding file. Compare to 2712 i2c
controller, MT8183 has different registers, offsets, clock,
and multi-user function.
Signed-off-by: qii wang <qii.wang@mediatek.com>
---
Documentation/devicetree/bindings/i2c/i2c-mtk.txt | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt
index ee4c324..0d29a5b 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt
@@ -12,14 +12,15 @@ Required properties:
"mediatek,mt7623-i2c", "mediatek,mt6577-i2c": for MediaTek MT7623
"mediatek,mt7629-i2c", "mediatek,mt2712-i2c": for MediaTek MT7629
"mediatek,mt8173-i2c": for MediaTek MT8173
+ "mediatek,mt8183-i2c": for MediaTek MT8183
- reg: physical base address of the controller and dma base, length of memory
mapped region.
- interrupts: interrupt number to the cpu.
- clock-div: the fixed value for frequency divider of clock source in i2c
module. Each IC may be different.
- clocks: clock name from clock manager
- - clock-names: Must include "main" and "dma", if enable have-pmic need include
- "pmic" extra.
+ - clock-names: Must include "main" and "dma", "arb" is optional, if enable
+ have-pmic need include "pmic" extra.
Optional properties:
- clock-frequency: Frequency in Hz of the bus when transfer, the default value
@@ -27,6 +28,7 @@ Optional properties:
- mediatek,have-pmic: platform can control i2c form special pmic side.
Only mt6589 and mt8135 support this feature.
- mediatek,use-push-pull: IO config use push-pull mode.
+ - mediatek,share-i3c: i3c controller can share i2c function.
Example:
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 6/6] i2c: mediatek: Add i2c support for MediaTek MT8183
2018-12-21 12:58 [PATCH v2 0/6] add i2c support for mt7629 and mt8183 qii wang
` (4 preceding siblings ...)
2018-12-21 12:58 ` [PATCH 5/6] dt-bindings: i2c: Add Mediatek MT8183 i2c binding qii wang
@ 2018-12-21 12:58 ` qii wang
5 siblings, 0 replies; 11+ messages in thread
From: qii wang @ 2018-12-21 12:58 UTC (permalink / raw)
To: wsa
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
linux-mediatek, srv_heupstream, leilk.liu, qii.wang, ryder.lee
Add i2c compatible for MT8183. Compare to 2712 i2c controller, MT8183 has
different registers, offsets, clock, and multi-user function.
Signed-off-by: qii wang <qii.wang@mediatek.com>
---
drivers/i2c/busses/i2c-mt65xx.c | 127 ++++++++++++++++++++++++++++++++++++---
1 file changed, 120 insertions(+), 7 deletions(-)
diff --git a/drivers/i2c/busses/i2c-mt65xx.c b/drivers/i2c/busses/i2c-mt65xx.c
index 428ac99..19f0770 100644
--- a/drivers/i2c/busses/i2c-mt65xx.c
+++ b/drivers/i2c/busses/i2c-mt65xx.c
@@ -35,17 +35,21 @@
#include <linux/slab.h>
#define I2C_RS_TRANSFER (1 << 4)
+#define I2C_ARB_LOST (1 << 3)
#define I2C_HS_NACKERR (1 << 2)
#define I2C_ACKERR (1 << 1)
#define I2C_TRANSAC_COMP (1 << 0)
#define I2C_TRANSAC_START (1 << 0)
#define I2C_RS_MUL_CNFG (1 << 15)
#define I2C_RS_MUL_TRIG (1 << 14)
+#define I2C_HS_TIME_EN (1 << 7)
#define I2C_DCM_DISABLE 0x0000
#define I2C_IO_CONFIG_OPEN_DRAIN 0x0003
#define I2C_IO_CONFIG_PUSH_PULL 0x0000
#define I2C_SOFT_RST 0x0001
#define I2C_FIFO_ADDR_CLR 0x0001
+#define I2C_FIFO_ADDR_CLRH 0x0002
+#define I2C_HFIFO_DATA 0x8208
#define I2C_DELAY_LEN 0x0002
#define I2C_ST_START_CON 0x8001
#define I2C_FS_START_CON 0x1800
@@ -76,6 +80,8 @@
#define I2C_CONTROL_DIR_CHANGE (0x1 << 4)
#define I2C_CONTROL_ACKERR_DET_EN (0x1 << 5)
#define I2C_CONTROL_TRANSFER_LEN_CHANGE (0x1 << 6)
+#define I2C_CONTROL_DMAACK_EN (0x1 << 8)
+#define I2C_CONTROL_ASYNC_MODE (0x1 << 9)
#define I2C_CONTROL_WRAPPER (0x1 << 0)
#define I2C_DRV_NAME "i2c-mt65xx"
@@ -130,6 +136,15 @@ enum I2C_REGS_OFFSET {
OFFSET_DEBUGCTRL,
OFFSET_TRANSFER_LEN_AUX,
OFFSET_CLOCK_DIV,
+ /* MT8183 only regs */
+ OFFSET_LTIMING,
+ OFFSET_DATA_TIMING,
+ OFFSET_MCU_INTR,
+ OFFSET_HW_TIMEOUT,
+ OFFSET_HFIFO_DATA,
+ OFFSET_HFIFO_STAT,
+ OFFSET_MULTI_DMA,
+ OFFSET_ROLLBACK,
};
static const u16 mt_i2c_regs_v1[] = {
@@ -159,6 +174,39 @@ enum I2C_REGS_OFFSET {
[OFFSET_CLOCK_DIV] = 0x70,
};
+static const u16 mt_i2c_regs_v2[] = {
+ [OFFSET_DATA_PORT] = 0x0,
+ [OFFSET_SLAVE_ADDR] = 0x4,
+ [OFFSET_INTR_MASK] = 0x8,
+ [OFFSET_INTR_STAT] = 0xc,
+ [OFFSET_CONTROL] = 0x10,
+ [OFFSET_TRANSFER_LEN] = 0x14,
+ [OFFSET_TRANSAC_LEN] = 0x18,
+ [OFFSET_DELAY_LEN] = 0x1c,
+ [OFFSET_TIMING] = 0x20,
+ [OFFSET_START] = 0x24,
+ [OFFSET_EXT_CONF] = 0x28,
+ [OFFSET_LTIMING] = 0x2c,
+ [OFFSET_HS] = 0x30,
+ [OFFSET_IO_CONFIG] = 0x34,
+ [OFFSET_FIFO_ADDR_CLR] = 0x38,
+ [OFFSET_DATA_TIMING] = 0x3c,
+ [OFFSET_MCU_INTR] = 0x40,
+ [OFFSET_TRANSFER_LEN_AUX] = 0x44,
+ [OFFSET_CLOCK_DIV] = 0x48,
+ [OFFSET_HW_TIMEOUT] = 0x4c,
+ [OFFSET_SOFTRESET] = 0x50,
+ [OFFSET_HFIFO_DATA] = 0x70,
+ [OFFSET_DEBUGSTAT] = 0xe0,
+ [OFFSET_DEBUGCTRL] = 0xe8,
+ [OFFSET_FIFO_STAT] = 0xf4,
+ [OFFSET_FIFO_THRESH] = 0xf8,
+ [OFFSET_HFIFO_STAT] = 0xfc,
+ [OFFSET_DCM_EN] = 0xf88,
+ [OFFSET_MULTI_DMA] = 0xf8c,
+ [OFFSET_ROLLBACK] = 0xf98,
+};
+
struct mtk_i2c_compatible {
const struct i2c_adapter_quirks *quirks;
const u16 *regs;
@@ -168,6 +216,7 @@ struct mtk_i2c_compatible {
unsigned char aux_len_reg: 1;
unsigned char support_33bits: 1;
unsigned char timing_adjust: 1;
+ unsigned char dma_sync: 1;
};
struct mtk_i2c {
@@ -181,8 +230,10 @@ struct mtk_i2c {
struct clk *clk_main; /* main clock for i2c bus */
struct clk *clk_dma; /* DMA clock for i2c via DMA */
struct clk *clk_pmic; /* PMIC clock for i2c from PMIC */
+ struct clk *clk_arb; /* Arbitrator clock for i2c */
bool have_pmic; /* can use i2c pins from PMIC */
bool use_push_pull; /* IO config push-pull mode */
+ bool share_i3c; /* share i3c IP */
u16 irq_stat; /* interrupt status */
unsigned int clk_src_div;
@@ -190,6 +241,7 @@ struct mtk_i2c {
enum mtk_trans_op op;
u16 timing_reg;
u16 high_speed_reg;
+ u16 ltiming_reg;
unsigned char auto_restart;
bool ignore_restart_irq;
const struct mtk_i2c_compatible *dev_comp;
@@ -216,6 +268,7 @@ struct mtk_i2c {
.aux_len_reg = 1,
.support_33bits = 1,
.timing_adjust = 1,
+ .dma_sync = 0,
};
static const struct mtk_i2c_compatible mt6577_compat = {
@@ -227,6 +280,7 @@ struct mtk_i2c {
.aux_len_reg = 0,
.support_33bits = 0,
.timing_adjust = 0,
+ .dma_sync = 0,
};
static const struct mtk_i2c_compatible mt6589_compat = {
@@ -238,6 +292,7 @@ struct mtk_i2c {
.aux_len_reg = 0,
.support_33bits = 0,
.timing_adjust = 0,
+ .dma_sync = 0,
};
static const struct mtk_i2c_compatible mt7622_compat = {
@@ -249,6 +304,7 @@ struct mtk_i2c {
.aux_len_reg = 1,
.support_33bits = 0,
.timing_adjust = 0,
+ .dma_sync = 0,
};
static const struct mtk_i2c_compatible mt8173_compat = {
@@ -259,6 +315,18 @@ struct mtk_i2c {
.aux_len_reg = 1,
.support_33bits = 1,
.timing_adjust = 0,
+ .dma_sync = 0,
+};
+
+static const struct mtk_i2c_compatible mt8183_compat = {
+ .regs = mt_i2c_regs_v2,
+ .pmic_i2c = 0,
+ .dcm = 0,
+ .auto_restart = 1,
+ .aux_len_reg = 1,
+ .support_33bits = 1,
+ .timing_adjust = 1,
+ .dma_sync = 1,
};
static const struct of_device_id mtk_i2c_of_match[] = {
@@ -267,6 +335,7 @@ struct mtk_i2c {
{ .compatible = "mediatek,mt6589-i2c", .data = &mt6589_compat },
{ .compatible = "mediatek,mt7622-i2c", .data = &mt7622_compat },
{ .compatible = "mediatek,mt8173-i2c", .data = &mt8173_compat },
+ { .compatible = "mediatek,mt8183-i2c", .data = &mt8183_compat },
{}
};
MODULE_DEVICE_TABLE(of, mtk_i2c_of_match);
@@ -299,8 +368,18 @@ static int mtk_i2c_clock_enable(struct mtk_i2c *i2c)
if (ret)
goto err_pmic;
}
+
+ if (i2c->clk_arb) {
+ ret = clk_prepare_enable(i2c->clk_arb);
+ if (ret)
+ goto err_arb;
+ }
+
return 0;
+err_arb:
+ if (i2c->have_pmic)
+ clk_disable_unprepare(i2c->clk_pmic);
err_pmic:
clk_disable_unprepare(i2c->clk_main);
err_main:
@@ -311,6 +390,9 @@ static int mtk_i2c_clock_enable(struct mtk_i2c *i2c)
static void mtk_i2c_clock_disable(struct mtk_i2c *i2c)
{
+ if (i2c->clk_arb)
+ clk_disable_unprepare(i2c->clk_arb);
+
if (i2c->have_pmic)
clk_disable_unprepare(i2c->clk_pmic);
@@ -333,11 +415,19 @@ static void mtk_i2c_init_hw(struct mtk_i2c *i2c)
if (i2c->dev_comp->dcm)
mtk_i2c_writew(i2c, I2C_DCM_DISABLE, OFFSET_DCM_EN);
- if (i2c->dev_comp->timing_adjust)
+ if (i2c->dev_comp->timing_adjust && i2c->share_i3c) {
+ mtk_i2c_writew(i2c, (I2C_DEFAULT_CLK_DIV - 1) |
+ (I2C_DEFAULT_CLK_DIV - 1) << 8,
+ OFFSET_CLOCK_DIV);
+ i2c->high_speed_reg |= I2C_HS_TIME_EN;
+ } else {
mtk_i2c_writew(i2c, I2C_DEFAULT_CLK_DIV - 1, OFFSET_CLOCK_DIV);
+ }
mtk_i2c_writew(i2c, i2c->timing_reg, OFFSET_TIMING);
mtk_i2c_writew(i2c, i2c->high_speed_reg, OFFSET_HS);
+ if (i2c->dev_comp->regs == mt_i2c_regs_v2)
+ mtk_i2c_writew(i2c, i2c->ltiming_reg, OFFSET_LTIMING);
/* If use i2c pin from PMIC mt6397 side, need set PATH_DIR first */
if (i2c->have_pmic)
@@ -345,6 +435,9 @@ static void mtk_i2c_init_hw(struct mtk_i2c *i2c)
control_reg = I2C_CONTROL_ACKERR_DET_EN |
I2C_CONTROL_CLK_EXT_EN | I2C_CONTROL_DMA_EN;
+ if (i2c->dev_comp->dma_sync)
+ control_reg |= I2C_CONTROL_DMAACK_EN | I2C_CONTROL_ASYNC_MODE;
+
mtk_i2c_writew(i2c, control_reg, OFFSET_CONTROL);
mtk_i2c_writew(i2c, I2C_DELAY_LEN, OFFSET_DELAY_LEN);
@@ -434,6 +527,8 @@ static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk)
unsigned int clk_src;
unsigned int step_cnt;
unsigned int sample_cnt;
+ unsigned int l_step_cnt;
+ unsigned int l_sample_cnt;
unsigned int target_speed;
int ret;
@@ -443,11 +538,11 @@ static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk)
if (target_speed > MAX_FS_MODE_SPEED) {
/* Set master code speed register */
ret = mtk_i2c_calculate_speed(i2c, clk_src, MAX_FS_MODE_SPEED,
- &step_cnt, &sample_cnt);
+ &l_step_cnt, &l_sample_cnt);
if (ret < 0)
return ret;
- i2c->timing_reg = (sample_cnt << 8) | step_cnt;
+ i2c->timing_reg = (l_sample_cnt << 8) | l_step_cnt;
/* Set the high speed mode register */
ret = mtk_i2c_calculate_speed(i2c, clk_src, target_speed,
@@ -457,6 +552,8 @@ static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk)
i2c->high_speed_reg = I2C_TIME_DEFAULT_VALUE |
(sample_cnt << 12) | (step_cnt << 8);
+ i2c->ltiming_reg = (l_sample_cnt << 6) | l_step_cnt |
+ (sample_cnt << 12) | (step_cnt << 9);
} else {
ret = mtk_i2c_calculate_speed(i2c, clk_src, target_speed,
&step_cnt, &sample_cnt);
@@ -467,6 +564,8 @@ static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk)
/* Disable the high speed transaction */
i2c->high_speed_reg = I2C_TIME_CLR_VALUE;
+
+ i2c->ltiming_reg = (sample_cnt << 6) | step_cnt;
}
return 0;
@@ -483,6 +582,7 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
u16 addr_reg;
u16 start_reg;
u16 control_reg;
+ u16 fifo_clr_reg = I2C_FIFO_ADDR_CLR;
u16 restart_flag = 0;
u32 reg_4g_mode;
u8 *dma_rd_buf = NULL;
@@ -519,13 +619,21 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
/* Clear interrupt status */
mtk_i2c_writew(i2c, restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
- I2C_TRANSAC_COMP, OFFSET_INTR_STAT);
+ I2C_ARB_LOST | I2C_TRANSAC_COMP,
+ OFFSET_INTR_STAT);
+
+ if (i2c->share_i3c)
+ fifo_clr_reg |= I2C_FIFO_ADDR_CLRH;
- mtk_i2c_writew(i2c, I2C_FIFO_ADDR_CLR, OFFSET_FIFO_ADDR_CLR);
+ mtk_i2c_writew(i2c, fifo_clr_reg, OFFSET_FIFO_ADDR_CLR);
+
+ if ((i2c->speed_hz > MAX_FS_MODE_SPEED) && i2c->share_i3c)
+ mtk_i2c_writew(i2c, I2C_HFIFO_DATA, OFFSET_HFIFO_DATA);
/* Enable interrupt */
mtk_i2c_writew(i2c, restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
- I2C_TRANSAC_COMP, OFFSET_INTR_MASK);
+ I2C_ARB_LOST | I2C_TRANSAC_COMP,
+ OFFSET_INTR_MASK);
/* Set transfer and transaction len */
if (i2c->op == I2C_MASTER_WRRD) {
@@ -659,7 +767,7 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
/* Clear interrupt mask */
mtk_i2c_writew(i2c, ~(restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
- I2C_TRANSAC_COMP), OFFSET_INTR_MASK);
+ I2C_ARB_LOST | I2C_TRANSAC_COMP), OFFSET_INTR_MASK);
if (i2c->op == I2C_MASTER_WR) {
dma_unmap_single(i2c->dev, wpaddr,
@@ -817,6 +925,7 @@ static int mtk_i2c_parse_dt(struct device_node *np, struct mtk_i2c *i2c)
if (i2c->clk_src_div == 0)
return -EINVAL;
+ i2c->share_i3c = of_property_read_bool(np, "mediatek,share-i3c");
i2c->have_pmic = of_property_read_bool(np, "mediatek,have-pmic");
i2c->use_push_pull =
of_property_read_bool(np, "mediatek,use-push-pull");
@@ -884,6 +993,10 @@ static int mtk_i2c_probe(struct platform_device *pdev)
return PTR_ERR(i2c->clk_dma);
}
+ i2c->clk_arb = devm_clk_get(&pdev->dev, "arb");
+ if (IS_ERR(i2c->clk_arb))
+ i2c->clk_arb = NULL;
+
clk = i2c->clk_main;
if (i2c->have_pmic) {
i2c->clk_pmic = devm_clk_get(&pdev->dev, "pmic");
--
1.7.9.5
^ permalink raw reply related [flat|nested] 11+ messages in thread
* Re: [PATCH 4/6] i2c: mediatek: Add offsets array for new i2c registers
2018-12-21 12:58 ` [PATCH 4/6] i2c: mediatek: Add offsets array for new i2c registers qii wang
@ 2018-12-25 11:49 ` Nicolas Boichat
0 siblings, 0 replies; 11+ messages in thread
From: Nicolas Boichat @ 2018-12-25 11:49 UTC (permalink / raw)
To: qii wang
Cc: wsa, linux-i2c, devicetree, linux-arm Mailing List, lkml,
linux-mediatek, srv_heupstream, Leilk Liu, ryder.lee
On Fri, Dec 21, 2018 at 8:59 PM qii wang <qii.wang@mediatek.com> wrote:
>
> New i2c registers would have different offsets, so we use different
> offsets array to distinguish different i2c registers version.
>
> Signed-off-by: qii wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
> ---
> drivers/i2c/busses/i2c-mt65xx.c | 163 +++++++++++++++++++++++++--------------
> 1 file changed, 104 insertions(+), 59 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-mt65xx.c b/drivers/i2c/busses/i2c-mt65xx.c
> index 660de1e..428ac99 100644
> --- a/drivers/i2c/busses/i2c-mt65xx.c
> +++ b/drivers/i2c/busses/i2c-mt65xx.c
> @@ -106,34 +106,62 @@ enum mtk_trans_op {
> };
>
> enum I2C_REGS_OFFSET {
> - OFFSET_DATA_PORT = 0x0,
> - OFFSET_SLAVE_ADDR = 0x04,
> - OFFSET_INTR_MASK = 0x08,
> - OFFSET_INTR_STAT = 0x0c,
> - OFFSET_CONTROL = 0x10,
> - OFFSET_TRANSFER_LEN = 0x14,
> - OFFSET_TRANSAC_LEN = 0x18,
> - OFFSET_DELAY_LEN = 0x1c,
> - OFFSET_TIMING = 0x20,
> - OFFSET_START = 0x24,
> - OFFSET_EXT_CONF = 0x28,
> - OFFSET_FIFO_STAT = 0x30,
> - OFFSET_FIFO_THRESH = 0x34,
> - OFFSET_FIFO_ADDR_CLR = 0x38,
> - OFFSET_IO_CONFIG = 0x40,
> - OFFSET_RSV_DEBUG = 0x44,
> - OFFSET_HS = 0x48,
> - OFFSET_SOFTRESET = 0x50,
> - OFFSET_DCM_EN = 0x54,
> - OFFSET_PATH_DIR = 0x60,
> - OFFSET_DEBUGSTAT = 0x64,
> - OFFSET_DEBUGCTRL = 0x68,
> - OFFSET_TRANSFER_LEN_AUX = 0x6c,
> - OFFSET_CLOCK_DIV = 0x70,
> + OFFSET_DATA_PORT,
> + OFFSET_SLAVE_ADDR,
> + OFFSET_INTR_MASK,
> + OFFSET_INTR_STAT,
> + OFFSET_CONTROL,
> + OFFSET_TRANSFER_LEN,
> + OFFSET_TRANSAC_LEN,
> + OFFSET_DELAY_LEN,
> + OFFSET_TIMING,
> + OFFSET_START,
> + OFFSET_EXT_CONF,
> + OFFSET_FIFO_STAT,
> + OFFSET_FIFO_THRESH,
> + OFFSET_FIFO_ADDR_CLR,
> + OFFSET_IO_CONFIG,
> + OFFSET_RSV_DEBUG,
> + OFFSET_HS,
> + OFFSET_SOFTRESET,
> + OFFSET_DCM_EN,
> + OFFSET_PATH_DIR,
> + OFFSET_DEBUGSTAT,
> + OFFSET_DEBUGCTRL,
> + OFFSET_TRANSFER_LEN_AUX,
> + OFFSET_CLOCK_DIV,
> +};
> +
> +static const u16 mt_i2c_regs_v1[] = {
> + [OFFSET_DATA_PORT] = 0x0,
> + [OFFSET_SLAVE_ADDR] = 0x4,
> + [OFFSET_INTR_MASK] = 0x8,
> + [OFFSET_INTR_STAT] = 0xc,
> + [OFFSET_CONTROL] = 0x10,
> + [OFFSET_TRANSFER_LEN] = 0x14,
> + [OFFSET_TRANSAC_LEN] = 0x18,
> + [OFFSET_DELAY_LEN] = 0x1c,
> + [OFFSET_TIMING] = 0x20,
> + [OFFSET_START] = 0x24,
> + [OFFSET_EXT_CONF] = 0x28,
> + [OFFSET_FIFO_STAT] = 0x30,
> + [OFFSET_FIFO_THRESH] = 0x34,
> + [OFFSET_FIFO_ADDR_CLR] = 0x38,
> + [OFFSET_IO_CONFIG] = 0x40,
> + [OFFSET_RSV_DEBUG] = 0x44,
> + [OFFSET_HS] = 0x48,
> + [OFFSET_SOFTRESET] = 0x50,
> + [OFFSET_DCM_EN] = 0x54,
> + [OFFSET_PATH_DIR] = 0x60,
> + [OFFSET_DEBUGSTAT] = 0x64,
> + [OFFSET_DEBUGCTRL] = 0x68,
> + [OFFSET_TRANSFER_LEN_AUX] = 0x6c,
> + [OFFSET_CLOCK_DIV] = 0x70,
> };
>
> struct mtk_i2c_compatible {
> const struct i2c_adapter_quirks *quirks;
> + const u16 *regs;
> unsigned char pmic_i2c: 1;
> unsigned char dcm: 1;
> unsigned char auto_restart: 1;
> @@ -181,6 +209,7 @@ struct mtk_i2c {
> };
>
> static const struct mtk_i2c_compatible mt2712_compat = {
> + .regs = mt_i2c_regs_v1,
> .pmic_i2c = 0,
> .dcm = 1,
> .auto_restart = 1,
> @@ -191,6 +220,7 @@ struct mtk_i2c {
>
> static const struct mtk_i2c_compatible mt6577_compat = {
> .quirks = &mt6577_i2c_quirks,
> + .regs = mt_i2c_regs_v1,
> .pmic_i2c = 0,
> .dcm = 1,
> .auto_restart = 0,
> @@ -201,6 +231,7 @@ struct mtk_i2c {
>
> static const struct mtk_i2c_compatible mt6589_compat = {
> .quirks = &mt6577_i2c_quirks,
> + .regs = mt_i2c_regs_v1,
> .pmic_i2c = 1,
> .dcm = 0,
> .auto_restart = 0,
> @@ -211,6 +242,7 @@ struct mtk_i2c {
>
> static const struct mtk_i2c_compatible mt7622_compat = {
> .quirks = &mt7622_i2c_quirks,
> + .regs = mt_i2c_regs_v1,
> .pmic_i2c = 0,
> .dcm = 1,
> .auto_restart = 1,
> @@ -220,6 +252,7 @@ struct mtk_i2c {
> };
>
> static const struct mtk_i2c_compatible mt8173_compat = {
> + .regs = mt_i2c_regs_v1,
> .pmic_i2c = 0,
> .dcm = 1,
> .auto_restart = 1,
> @@ -238,6 +271,17 @@ struct mtk_i2c {
> };
> MODULE_DEVICE_TABLE(of, mtk_i2c_of_match);
>
> +static u16 mtk_i2c_readw(struct mtk_i2c *i2c, enum I2C_REGS_OFFSET reg)
> +{
> + return readw(i2c->base + i2c->dev_comp->regs[reg]);
> +}
> +
> +static void mtk_i2c_writew(struct mtk_i2c *i2c, u16 val,
> + enum I2C_REGS_OFFSET reg)
> +{
> + writew(val, i2c->base + i2c->dev_comp->regs[reg]);
> +}
> +
> static int mtk_i2c_clock_enable(struct mtk_i2c *i2c)
> {
> int ret;
> @@ -278,31 +322,31 @@ static void mtk_i2c_init_hw(struct mtk_i2c *i2c)
> {
> u16 control_reg;
>
> - writew(I2C_SOFT_RST, i2c->base + OFFSET_SOFTRESET);
> + mtk_i2c_writew(i2c, I2C_SOFT_RST, OFFSET_SOFTRESET);
>
> /* Set ioconfig */
> if (i2c->use_push_pull)
> - writew(I2C_IO_CONFIG_PUSH_PULL, i2c->base + OFFSET_IO_CONFIG);
> + mtk_i2c_writew(i2c, I2C_IO_CONFIG_PUSH_PULL, OFFSET_IO_CONFIG);
> else
> - writew(I2C_IO_CONFIG_OPEN_DRAIN, i2c->base + OFFSET_IO_CONFIG);
> + mtk_i2c_writew(i2c, I2C_IO_CONFIG_OPEN_DRAIN, OFFSET_IO_CONFIG);
>
> if (i2c->dev_comp->dcm)
> - writew(I2C_DCM_DISABLE, i2c->base + OFFSET_DCM_EN);
> + mtk_i2c_writew(i2c, I2C_DCM_DISABLE, OFFSET_DCM_EN);
>
> if (i2c->dev_comp->timing_adjust)
> - writew(I2C_DEFAULT_CLK_DIV - 1, i2c->base + OFFSET_CLOCK_DIV);
> + mtk_i2c_writew(i2c, I2C_DEFAULT_CLK_DIV - 1, OFFSET_CLOCK_DIV);
>
> - writew(i2c->timing_reg, i2c->base + OFFSET_TIMING);
> - writew(i2c->high_speed_reg, i2c->base + OFFSET_HS);
> + mtk_i2c_writew(i2c, i2c->timing_reg, OFFSET_TIMING);
> + mtk_i2c_writew(i2c, i2c->high_speed_reg, OFFSET_HS);
>
> /* If use i2c pin from PMIC mt6397 side, need set PATH_DIR first */
> if (i2c->have_pmic)
> - writew(I2C_CONTROL_WRAPPER, i2c->base + OFFSET_PATH_DIR);
> + mtk_i2c_writew(i2c, I2C_CONTROL_WRAPPER, OFFSET_PATH_DIR);
>
> control_reg = I2C_CONTROL_ACKERR_DET_EN |
> I2C_CONTROL_CLK_EXT_EN | I2C_CONTROL_DMA_EN;
> - writew(control_reg, i2c->base + OFFSET_CONTROL);
> - writew(I2C_DELAY_LEN, i2c->base + OFFSET_DELAY_LEN);
> + mtk_i2c_writew(i2c, control_reg, OFFSET_CONTROL);
> + mtk_i2c_writew(i2c, I2C_DELAY_LEN, OFFSET_DELAY_LEN);
>
> writel(I2C_DMA_HARD_RST, i2c->pdmabase + OFFSET_RST);
> udelay(50);
> @@ -454,7 +498,7 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
>
> reinit_completion(&i2c->msg_complete);
>
> - control_reg = readw(i2c->base + OFFSET_CONTROL) &
> + control_reg = mtk_i2c_readw(i2c, OFFSET_CONTROL) &
> ~(I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS);
> if ((i2c->speed_hz > MAX_FS_MODE_SPEED) || (left_num >= 1))
> control_reg |= I2C_CONTROL_RS;
> @@ -462,40 +506,41 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
> if (i2c->op == I2C_MASTER_WRRD)
> control_reg |= I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS;
>
> - writew(control_reg, i2c->base + OFFSET_CONTROL);
> + mtk_i2c_writew(i2c, control_reg, OFFSET_CONTROL);
>
> /* set start condition */
> if (i2c->speed_hz <= I2C_DEFAULT_SPEED)
> - writew(I2C_ST_START_CON, i2c->base + OFFSET_EXT_CONF);
> + mtk_i2c_writew(i2c, I2C_ST_START_CON, OFFSET_EXT_CONF);
> else
> - writew(I2C_FS_START_CON, i2c->base + OFFSET_EXT_CONF);
> + mtk_i2c_writew(i2c, I2C_FS_START_CON, OFFSET_EXT_CONF);
>
> addr_reg = i2c_8bit_addr_from_msg(msgs);
> - writew(addr_reg, i2c->base + OFFSET_SLAVE_ADDR);
> + mtk_i2c_writew(i2c, addr_reg, OFFSET_SLAVE_ADDR);
>
> /* Clear interrupt status */
> - writew(restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
> - I2C_TRANSAC_COMP, i2c->base + OFFSET_INTR_STAT);
> - writew(I2C_FIFO_ADDR_CLR, i2c->base + OFFSET_FIFO_ADDR_CLR);
> + mtk_i2c_writew(i2c, restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
> + I2C_TRANSAC_COMP, OFFSET_INTR_STAT);
> +
> + mtk_i2c_writew(i2c, I2C_FIFO_ADDR_CLR, OFFSET_FIFO_ADDR_CLR);
>
> /* Enable interrupt */
> - writew(restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
> - I2C_TRANSAC_COMP, i2c->base + OFFSET_INTR_MASK);
> + mtk_i2c_writew(i2c, restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
> + I2C_TRANSAC_COMP, OFFSET_INTR_MASK);
>
> /* Set transfer and transaction len */
> if (i2c->op == I2C_MASTER_WRRD) {
> if (i2c->dev_comp->aux_len_reg) {
> - writew(msgs->len, i2c->base + OFFSET_TRANSFER_LEN);
> - writew((msgs + 1)->len, i2c->base +
> - OFFSET_TRANSFER_LEN_AUX);
> + mtk_i2c_writew(i2c, msgs->len, OFFSET_TRANSFER_LEN);
> + mtk_i2c_writew(i2c, (msgs + 1)->len,
> + OFFSET_TRANSFER_LEN_AUX);
> } else {
> - writew(msgs->len | ((msgs + 1)->len) << 8,
> - i2c->base + OFFSET_TRANSFER_LEN);
> + mtk_i2c_writew(i2c, msgs->len | ((msgs + 1)->len) << 8,
> + OFFSET_TRANSFER_LEN);
> }
> - writew(I2C_WRRD_TRANAC_VALUE, i2c->base + OFFSET_TRANSAC_LEN);
> + mtk_i2c_writew(i2c, I2C_WRRD_TRANAC_VALUE, OFFSET_TRANSAC_LEN);
> } else {
> - writew(msgs->len, i2c->base + OFFSET_TRANSFER_LEN);
> - writew(num, i2c->base + OFFSET_TRANSAC_LEN);
> + mtk_i2c_writew(i2c, msgs->len, OFFSET_TRANSFER_LEN);
> + mtk_i2c_writew(i2c, num, OFFSET_TRANSAC_LEN);
> }
>
> /* Prepare buffer data to start transfer */
> @@ -607,14 +652,14 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
> if (left_num >= 1)
> start_reg |= I2C_RS_MUL_CNFG;
> }
> - writew(start_reg, i2c->base + OFFSET_START);
> + mtk_i2c_writew(i2c, start_reg, OFFSET_START);
>
> ret = wait_for_completion_timeout(&i2c->msg_complete,
> i2c->adap.timeout);
>
> /* Clear interrupt mask */
> - writew(~(restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
> - I2C_TRANSAC_COMP), i2c->base + OFFSET_INTR_MASK);
> + mtk_i2c_writew(i2c, ~(restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
> + I2C_TRANSAC_COMP), OFFSET_INTR_MASK);
>
> if (i2c->op == I2C_MASTER_WR) {
> dma_unmap_single(i2c->dev, wpaddr,
> @@ -724,8 +769,8 @@ static irqreturn_t mtk_i2c_irq(int irqno, void *dev_id)
> if (i2c->auto_restart)
> restart_flag = I2C_RS_TRANSFER;
>
> - intr_stat = readw(i2c->base + OFFSET_INTR_STAT);
> - writew(intr_stat, i2c->base + OFFSET_INTR_STAT);
> + intr_stat = mtk_i2c_readw(i2c, OFFSET_INTR_STAT);
> + mtk_i2c_writew(i2c, intr_stat, OFFSET_INTR_STAT);
>
> /*
> * when occurs ack error, i2c controller generate two interrupts
> @@ -737,8 +782,8 @@ static irqreturn_t mtk_i2c_irq(int irqno, void *dev_id)
> if (i2c->ignore_restart_irq && (i2c->irq_stat & restart_flag)) {
> i2c->ignore_restart_irq = false;
> i2c->irq_stat = 0;
> - writew(I2C_RS_MUL_CNFG | I2C_RS_MUL_TRIG | I2C_TRANSAC_START,
> - i2c->base + OFFSET_START);
> + mtk_i2c_writew(i2c, I2C_RS_MUL_CNFG | I2C_RS_MUL_TRIG |
> + I2C_TRANSAC_START, OFFSET_START);
> } else {
> if (i2c->irq_stat & (I2C_TRANSAC_COMP | restart_flag))
> complete(&i2c->msg_complete);
> --
> 1.7.9.5
>
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH 2/6] i2c: mediatek: speeds is replaced by macros definitions
2018-12-21 12:58 ` [PATCH 2/6] i2c: mediatek: speeds is replaced by macros definitions qii wang
@ 2018-12-25 11:51 ` Nicolas Boichat
0 siblings, 0 replies; 11+ messages in thread
From: Nicolas Boichat @ 2018-12-25 11:51 UTC (permalink / raw)
To: qii wang
Cc: wsa, linux-i2c, devicetree, linux-arm Mailing List, lkml,
linux-mediatek, srv_heupstream, Leilk Liu, Ryder Lee
On Fri, Dec 21, 2018 at 8:59 PM qii wang <qii.wang@mediatek.com> wrote:
>
> Different speeds have been defined by macros,
> so we use macros definitions.
>
> Signed-off-by: qii wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
> ---
> drivers/i2c/busses/i2c-mt65xx.c | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-mt65xx.c b/drivers/i2c/busses/i2c-mt65xx.c
> index a74ef76..7396449 100644
> --- a/drivers/i2c/busses/i2c-mt65xx.c
> +++ b/drivers/i2c/busses/i2c-mt65xx.c
> @@ -456,7 +456,7 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
>
> control_reg = readw(i2c->base + OFFSET_CONTROL) &
> ~(I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS);
> - if ((i2c->speed_hz > 400000) || (left_num >= 1))
> + if ((i2c->speed_hz > MAX_FS_MODE_SPEED) || (left_num >= 1))
> control_reg |= I2C_CONTROL_RS;
>
> if (i2c->op == I2C_MASTER_WRRD)
> @@ -465,7 +465,7 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
> writew(control_reg, i2c->base + OFFSET_CONTROL);
>
> /* set start condition */
> - if (i2c->speed_hz <= 100000)
> + if (i2c->speed_hz <= I2C_DEFAULT_SPEED)
> writew(I2C_ST_START_CON, i2c->base + OFFSET_EXT_CONF);
> else
> writew(I2C_FS_START_CON, i2c->base + OFFSET_EXT_CONF);
> --
> 1.7.9.5
>
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH 1/6] dt-bindings: i2c: Add Mediatek MT7629 i2c binding
2018-12-21 12:58 ` [PATCH 1/6] dt-bindings: i2c: Add Mediatek MT7629 i2c binding qii wang
@ 2019-01-03 19:21 ` Rob Herring
0 siblings, 0 replies; 11+ messages in thread
From: Rob Herring @ 2019-01-03 19:21 UTC (permalink / raw)
To: qii wang
Cc: wsa, linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
linux-mediatek, srv_heupstream, leilk.liu, qii.wang, ryder.lee
On Fri, 21 Dec 2018 20:58:26 +0800, qii wang wrote:
> Add MT7629 i2c binding to binding file.
>
> Signed-off-by: qii wang <qii.wang@mediatek.com>
> ---
> Documentation/devicetree/bindings/i2c/i2c-mtk.txt | 1 +
> 1 file changed, 1 insertion(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH 5/6] dt-bindings: i2c: Add Mediatek MT8183 i2c binding
2018-12-21 12:58 ` [PATCH 5/6] dt-bindings: i2c: Add Mediatek MT8183 i2c binding qii wang
@ 2019-01-03 19:23 ` Rob Herring
0 siblings, 0 replies; 11+ messages in thread
From: Rob Herring @ 2019-01-03 19:23 UTC (permalink / raw)
To: qii wang
Cc: wsa, linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
linux-mediatek, srv_heupstream, leilk.liu, qii.wang, ryder.lee
On Fri, 21 Dec 2018 20:58:30 +0800, qii wang wrote:
> Add MT8183 i2c binding to binding file. Compare to 2712 i2c
> controller, MT8183 has different registers, offsets, clock,
> and multi-user function.
>
> Signed-off-by: qii wang <qii.wang@mediatek.com>
> ---
> Documentation/devicetree/bindings/i2c/i2c-mtk.txt | 6 ++++--
> 1 file changed, 4 insertions(+), 2 deletions(-)
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2019-01-03 19:23 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-12-21 12:58 [PATCH v2 0/6] add i2c support for mt7629 and mt8183 qii wang
2018-12-21 12:58 ` [PATCH 1/6] dt-bindings: i2c: Add Mediatek MT7629 i2c binding qii wang
2019-01-03 19:21 ` Rob Herring
2018-12-21 12:58 ` [PATCH 2/6] i2c: mediatek: speeds is replaced by macros definitions qii wang
2018-12-25 11:51 ` Nicolas Boichat
2018-12-21 12:58 ` [PATCH 3/6] i2c: mediatek: remove completion_done() qii wang
2018-12-21 12:58 ` [PATCH 4/6] i2c: mediatek: Add offsets array for new i2c registers qii wang
2018-12-25 11:49 ` Nicolas Boichat
2018-12-21 12:58 ` [PATCH 5/6] dt-bindings: i2c: Add Mediatek MT8183 i2c binding qii wang
2019-01-03 19:23 ` Rob Herring
2018-12-21 12:58 ` [PATCH 6/6] i2c: mediatek: Add i2c support for MediaTek MT8183 qii wang
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).