From: <Claudiu.Beznea@microchip.com>
To: <linus.walleij@linaro.org>, <robh+dt@kernel.org>,
<mark.rutland@arm.com>, <Nicolas.Ferre@microchip.com>,
<alexandre.belloni@bootlin.com>,
<Ludovic.Desroches@microchip.com>
Cc: <linux-gpio@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <Claudiu.Beznea@microchip.com>
Subject: [PATCH 2/7] pinctrl: at91: add drive strength support for SAM9X60
Date: Thu, 31 Jan 2019 12:29:29 +0000 [thread overview]
Message-ID: <1548937733-20189-3-git-send-email-claudiu.beznea@microchip.com> (raw)
In-Reply-To: <1548937733-20189-1-git-send-email-claudiu.beznea@microchip.com>
From: Claudiu Beznea <claudiu.beznea@microchip.com>
Add drive strength support for SAM9X60 pin controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
---
drivers/pinctrl/pinctrl-at91.c | 52 ++++++++++++++++++++++++++++++++++++++++++
drivers/pinctrl/pinctrl-at91.h | 2 ++
2 files changed, 54 insertions(+)
diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c
index 31f06dafca2e..46443b97d811 100644
--- a/drivers/pinctrl/pinctrl-at91.c
+++ b/drivers/pinctrl/pinctrl-at91.c
@@ -574,6 +574,17 @@ static unsigned at91_mux_sam9x5_get_drivestrength(void __iomem *pio,
return tmp;
}
+static unsigned at91_mux_sam9x60_get_drivestrength(void __iomem *pio,
+ unsigned pin)
+{
+ unsigned tmp = readl_relaxed(pio + SAM9X60_PIO_DRIVER1);
+
+ if (tmp & BIT(pin))
+ return DRIVE_STRENGTH_BIT_HI;
+
+ return DRIVE_STRENGTH_BIT_LOW;
+}
+
static void set_drive_strength(void __iomem *reg, unsigned pin, u32 strength)
{
unsigned tmp = readl_relaxed(reg);
@@ -611,6 +622,27 @@ static void at91_mux_sam9x5_set_drivestrength(void __iomem *pio, unsigned pin,
setting);
}
+static void at91_mux_sam9x60_set_drivestrength(void __iomem *pio, unsigned pin,
+ u32 setting)
+{
+ unsigned int tmp;
+
+ if (setting <= DRIVE_STRENGTH_BIT_DEF ||
+ setting == DRIVE_STRENGTH_BIT_MED ||
+ setting > DRIVE_STRENGTH_BIT_HI)
+ return;
+
+ tmp = readl_relaxed(pio + SAM9X60_PIO_DRIVER1);
+
+ /* Strength is 0: low, 1: hi */
+ if (setting == DRIVE_STRENGTH_BIT_LOW)
+ tmp &= ~BIT(pin);
+ else
+ tmp |= BIT(pin);
+
+ writel_relaxed(tmp, pio + SAM9X60_PIO_DRIVER1);
+}
+
static struct at91_pinctrl_mux_ops at91rm9200_ops = {
.get_periph = at91_mux_get_periph,
.mux_A_periph = at91_mux_set_A_periph,
@@ -639,6 +671,26 @@ static struct at91_pinctrl_mux_ops at91sam9x5_ops = {
.irq_type = alt_gpio_irq_type,
};
+static const struct at91_pinctrl_mux_ops sam9x60_ops = {
+ .get_periph = at91_mux_pio3_get_periph,
+ .mux_A_periph = at91_mux_pio3_set_A_periph,
+ .mux_B_periph = at91_mux_pio3_set_B_periph,
+ .mux_C_periph = at91_mux_pio3_set_C_periph,
+ .mux_D_periph = at91_mux_pio3_set_D_periph,
+ .get_deglitch = at91_mux_pio3_get_deglitch,
+ .set_deglitch = at91_mux_pio3_set_deglitch,
+ .get_debounce = at91_mux_pio3_get_debounce,
+ .set_debounce = at91_mux_pio3_set_debounce,
+ .get_pulldown = at91_mux_pio3_get_pulldown,
+ .set_pulldown = at91_mux_pio3_set_pulldown,
+ .get_schmitt_trig = at91_mux_pio3_get_schmitt_trig,
+ .disable_schmitt_trig = at91_mux_pio3_disable_schmitt_trig,
+ .get_drivestrength = at91_mux_sam9x60_get_drivestrength,
+ .set_drivestrength = at91_mux_sam9x60_set_drivestrength,
+ .irq_type = alt_gpio_irq_type,
+
+};
+
static struct at91_pinctrl_mux_ops sama5d3_ops = {
.get_periph = at91_mux_pio3_get_periph,
.mux_A_periph = at91_mux_pio3_set_A_periph,
diff --git a/drivers/pinctrl/pinctrl-at91.h b/drivers/pinctrl/pinctrl-at91.h
index 79b957f1dfa2..19fc27e66bfd 100644
--- a/drivers/pinctrl/pinctrl-at91.h
+++ b/drivers/pinctrl/pinctrl-at91.h
@@ -69,4 +69,6 @@
#define AT91SAM9X5_PIO_DRIVER1 0x114 /*PIO Driver 1 register offset*/
#define AT91SAM9X5_PIO_DRIVER2 0x118 /*PIO Driver 2 register offset*/
+#define SAM9X60_PIO_DRIVER1 0x118 /* PIO Driver 1 register offset */
+
#endif
--
2.7.4
next prev parent reply other threads:[~2019-01-31 12:29 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-31 12:29 [PATCH 0/7] add support for SAM9X60 pin controller Claudiu.Beznea
2019-01-31 12:29 ` [PATCH 1/7] pinctrl: at91: add option to use drive strength bits Claudiu.Beznea
2019-01-31 12:29 ` Claudiu.Beznea [this message]
2019-01-31 12:29 ` [PATCH 3/7] pinctrl: at91: add compatibles for SAM9X60 pin controller Claudiu.Beznea
2019-01-31 12:33 ` Ludovic Desroches
2019-01-31 16:16 ` Claudiu.Beznea
2019-01-31 12:29 ` [PATCH 4/7] dt-bindings: add documentation for banks Claudiu.Beznea
2019-01-31 12:29 ` [PATCH 5/7] dt-bindings: add bindings for SAM9X60 Claudiu.Beznea
2019-01-31 12:36 ` Ludovic Desroches
2019-01-31 12:29 ` [PATCH 6/7] pinctrl: at91: add slewrate support " Claudiu.Beznea
2019-01-31 12:29 ` [PATCH 7/7] dt-bindings: add documentation for slew rate Claudiu.Beznea
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1548937733-20189-3-git-send-email-claudiu.beznea@microchip.com \
--to=claudiu.beznea@microchip.com \
--cc=Ludovic.Desroches@microchip.com \
--cc=Nicolas.Ferre@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).