* Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6.
@ 2019-11-29 8:48 Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 01/12] MIPS: Ingenic: Initial X1000 support Zhou Yanjie
` (10 more replies)
0 siblings, 11 replies; 12+ messages in thread
From: Zhou Yanjie @ 2019-11-29 8:48 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
jhogan, mripard, shawnguo, mark.rutland, syq, ralf, heiko,
icenowy, laurent.pinchart, krzk, geert+renesas, paul,
prasannatsmkumar, sernia.zhou, zhenwenjin, 772753199
v5->v6:
1.Use "stdout-path = "serial2:115200n8"" instead "stdout-path = &uart2" in DT.
2.Remove "console=ttyS2,115200n8" and "CONFIG_CMDLINE_OVERRIDE=y" from defconfg.
3.Add watchdog timer DT node, and update defconfig for watchdog timer.
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v6 01/12] MIPS: Ingenic: Initial X1000 support.
2019-11-29 8:48 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Zhou Yanjie
@ 2019-11-29 8:48 ` Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 02/12] dt-bindings: Document yna vendor-prefix Zhou Yanjie
` (9 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Zhou Yanjie @ 2019-11-29 8:48 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
jhogan, mripard, shawnguo, mark.rutland, syq, ralf, heiko,
icenowy, laurent.pinchart, krzk, geert+renesas, paul,
prasannatsmkumar, sernia.zhou, zhenwenjin, 772753199
Support the Ingenic X1000 SoC using the code under arch/mips/jz4740.
This is left unselectable in Kconfig until a X1000 based board is
added in a later commit.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
Notes:
v1->v2:
Rebase on top of mips-next, use ingenic-timer driver
for system timer and clocksource.
v2->v3:
Drop the 'apb' node.
v3->v4:
Adjust the node order to make it consistent with
other Ingenic boards.
v4->v5:
No change.
v5->v6:
No change.
arch/mips/boot/dts/ingenic/x1000.dtsi | 176 ++++++++++++++++++++++++++++++++++
arch/mips/jz4740/Kconfig | 6 ++
2 files changed, 182 insertions(+)
create mode 100644 arch/mips/boot/dts/ingenic/x1000.dtsi
diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi b/arch/mips/boot/dts/ingenic/x1000.dtsi
new file mode 100644
index 00000000..13a6c9ff
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
@@ -0,0 +1,176 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/x1000-cgu.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "ingenic,x1000", "ingenic,x1000e";
+
+ cpuintc: interrupt-controller {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ compatible = "mti,cpu-interrupt-controller";
+ };
+
+ intc: interrupt-controller@10001000 {
+ compatible = "ingenic,x1000-intc", "ingenic,jz4780-intc";
+ reg = <0x10001000 0x50>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&cpuintc>;
+ interrupts = <2>;
+ };
+
+ exclk: ext {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+
+ rtclk: rtc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+
+ cgu: x1000-cgu@10000000 {
+ compatible = "ingenic,x1000-cgu";
+ reg = <0x10000000 0x100>;
+
+ #clock-cells = <1>;
+
+ clocks = <&exclk>, <&rtclk>;
+ clock-names = "ext", "rtc";
+ };
+
+ tcu: timer@10002000 {
+ compatible = "ingenic,x1000-tcu",
+ "ingenic,jz4770-tcu",
+ "simple-mfd";
+ reg = <0x10002000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x10002000 0x1000>;
+
+ #clock-cells = <1>;
+
+ clocks = <&cgu X1000_CLK_RTCLK
+ &cgu X1000_CLK_EXCLK
+ &cgu X1000_CLK_PCLK>;
+ clock-names = "rtc", "ext", "pclk";
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <27 26 25>;
+ };
+
+ pinctrl: pin-controller@10010000 {
+ compatible = "ingenic,x1000-pinctrl";
+ reg = <0x10010000 0x800>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpa: gpio@0 {
+ compatible = "ingenic,x1000-gpio";
+ reg = <0>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 0 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <17>;
+ };
+
+ gpb: gpio@1 {
+ compatible = "ingenic,x1000-gpio";
+ reg = <1>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 32 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <16>;
+ };
+
+ gpc: gpio@2 {
+ compatible = "ingenic,x1000-gpio";
+ reg = <2>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 64 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <15>;
+ };
+
+ gpd: gpio@3 {
+ compatible = "ingenic,x1000-gpio";
+ reg = <3>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 96 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <14>;
+ };
+ };
+
+ uart0: serial@10030000 {
+ compatible = "ingenic,x1000-uart";
+ reg = <0x10030000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <51>;
+
+ clocks = <&exclk>, <&cgu X1000_CLK_UART0>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+
+ uart1: serial@10031000 {
+ compatible = "ingenic,x1000-uart";
+ reg = <0x10031000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <50>;
+
+ clocks = <&exclk>, <&cgu X1000_CLK_UART1>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+
+ uart2: serial@10032000 {
+ compatible = "ingenic,x1000-uart";
+ reg = <0x10032000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <49>;
+
+ clocks = <&exclk>, <&cgu X1000_CLK_UART2>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+};
diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
index 4dd0c44..6b96844 100644
--- a/arch/mips/jz4740/Kconfig
+++ b/arch/mips/jz4740/Kconfig
@@ -33,3 +33,9 @@ config MACH_JZ4780
select MIPS_CPU_SCACHE
select SYS_HAS_CPU_MIPS32_R2
select SYS_SUPPORTS_HIGHMEM
+
+config MACH_X1000
+ bool
+ select MIPS_CPU_SCACHE
+ select SYS_HAS_CPU_MIPS32_R2
+ select SYS_SUPPORTS_HIGHMEM
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v6 02/12] dt-bindings: Document yna vendor-prefix.
2019-11-29 8:48 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 01/12] MIPS: Ingenic: Initial X1000 support Zhou Yanjie
@ 2019-11-29 8:48 ` Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 03/12] dt-bindings: MIPS: Add Ingenic XBurst based boards Zhou Yanjie
` (8 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Zhou Yanjie @ 2019-11-29 8:48 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
jhogan, mripard, shawnguo, mark.rutland, syq, ralf, heiko,
icenowy, laurent.pinchart, krzk, geert+renesas, paul,
prasannatsmkumar, sernia.zhou, zhenwenjin, 772753199
The "yna" is an acronym of the "YSH & ATIL".
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
Notes:
v1->v2:
No change.
v2->v3:
No change.
v3->v4:
No change.
v4->v5:
No change.
v5->v6:
No change.
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 967e78c..47ddd88 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1054,6 +1054,8 @@ patternProperties:
description: Xilinx
"^xunlong,.*":
description: Shenzhen Xunlong Software CO.,Limited
+ "^yna,.*":
+ description: YSH & ATIL
"^yones-toptech,.*":
description: Yones Toptech Co., Ltd.
"^ysoft,.*":
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v6 03/12] dt-bindings: MIPS: Add Ingenic XBurst based boards.
2019-11-29 8:48 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 01/12] MIPS: Ingenic: Initial X1000 support Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 02/12] dt-bindings: Document yna vendor-prefix Zhou Yanjie
@ 2019-11-29 8:48 ` Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 04/12] MIPS: Ingenic: Initial YSH & ATIL CU Neo board support Zhou Yanjie
` (7 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Zhou Yanjie @ 2019-11-29 8:48 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
jhogan, mripard, shawnguo, mark.rutland, syq, ralf, heiko,
icenowy, laurent.pinchart, krzk, geert+renesas, paul,
prasannatsmkumar, sernia.zhou, zhenwenjin, 772753199
Add Ingenic XBurst based boards, prepare for later dts.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
Notes:
v1->v2:
No change.
v2->v3:
No change.
v3->v4:
Adjust the description to make it more reasonable.
v4->v5:
Adjust item naming to prevent conflicts with
subsequent "CU Geo" boards.
v5->v6:
No change.
.../devicetree/bindings/mips/ingenic/devices.yaml | 35 ++++++++++++++++++++++
1 file changed, 35 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mips/ingenic/devices.yaml
diff --git a/Documentation/devicetree/bindings/mips/ingenic/devices.yaml b/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
new file mode 100644
index 00000000..6bba181
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
@@ -0,0 +1,35 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/ingenic/devices.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ingenic XBurst based Platforms Device Tree Bindings
+
+maintainers:
+ - Zhou Yanjie <zhouyanjie@zoho.com>
+description: |
+ Devices with a Ingenic XBurst CPU shall have the following properties.
+
+properties:
+ $nodename:
+ const: '/'
+ compatible:
+ oneOf:
+
+ - description: Qi Hardware Ben NanoNote
+ items:
+ - const: qi,lb60
+
+ - description: Game Consoles Worldwide GCW Zero
+ items:
+ - const: gcw,zero
+
+ - description: MIPS Creator CI20
+ items:
+ - const: img,ci20
+
+ - description: YSH & ATIL General Board CU Neo
+ items:
+ - const: yna,cu1000-neo
+...
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v6 04/12] MIPS: Ingenic: Initial YSH & ATIL CU Neo board support.
2019-11-29 8:48 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Zhou Yanjie
` (2 preceding siblings ...)
2019-11-29 8:48 ` [PATCH v6 03/12] dt-bindings: MIPS: Add Ingenic XBurst based boards Zhou Yanjie
@ 2019-11-29 8:48 ` Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 05/12] MIPS: X1000: Add pdma controller DT node Zhou Yanjie
` (6 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Zhou Yanjie @ 2019-11-29 8:48 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
jhogan, mripard, shawnguo, mark.rutland, syq, ralf, heiko,
icenowy, laurent.pinchart, krzk, geert+renesas, paul,
prasannatsmkumar, sernia.zhou, zhenwenjin, 772753199
Add a device tree for the Ingenic X1000 based YSH & ATIL CU Neo board.
Note that this is unselectable via Kconfig until the X1000 SoC is made
selectable in a later commit.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
Notes:
v1->v2:
Rebase on top of mips-next, use TCU for system timer and clocksource.
v2->v3:
No change.
v3->v4:
1.Adjust "model" in "cu1000.dts" to match the description in "devices.yaml".
2.Adjust "bool" in "Kconfig" to avoid duplicate names with subsequent boards.
v4->v5:
1.Rename "cu1000" to "cu1000-neo" to prevent conflicts with subsequent boards
such as "cu1000-geo", and so on.
2.Remove "CONFIG_HZ=100" and "mem=32M@0x0" from defconfg.
3.Modify incorrect comments in DT.
v5->v6:
1.Use "stdout-path = "serial2:115200n8"" instead "stdout-path = &uart2" in DT.
2.Remove "console=ttyS2,115200n8" and "CONFIG_CMDLINE_OVERRIDE=y" from defconfg.
arch/mips/boot/dts/ingenic/Makefile | 1 +
arch/mips/boot/dts/ingenic/cu1000-neo.dts | 52 ++++++++++++++++
arch/mips/configs/cu1000-neo_defconfig | 98 +++++++++++++++++++++++++++++++
arch/mips/jz4740/Kconfig | 4 ++
4 files changed, 155 insertions(+)
create mode 100644 arch/mips/boot/dts/ingenic/cu1000-neo.dts
create mode 100644 arch/mips/configs/cu1000-neo_defconfig
diff --git a/arch/mips/boot/dts/ingenic/Makefile b/arch/mips/boot/dts/ingenic/Makefile
index 9cc4844..e165429 100644
--- a/arch/mips/boot/dts/ingenic/Makefile
+++ b/arch/mips/boot/dts/ingenic/Makefile
@@ -2,5 +2,6 @@
dtb-$(CONFIG_JZ4740_QI_LB60) += qi_lb60.dtb
dtb-$(CONFIG_JZ4770_GCW0) += gcw0.dtb
dtb-$(CONFIG_JZ4780_CI20) += ci20.dtb
+dtb-$(CONFIG_X1000_CU1000_NEO) += cu1000-neo.dtb
obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
new file mode 100644
index 00000000..fb00439
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "x1000.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+
+/ {
+ compatible = "yna,cu1000-neo", "ingenic,x1000";
+ model = "YSH & ATIL General Board CU Neo";
+
+ aliases {
+ serial2 = &uart2;
+ };
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x04000000>;
+ };
+};
+
+&exclk {
+ clock-frequency = <24000000>;
+};
+
+&tcu {
+ /* 1500 kHz for the system timer and clocksource */
+ assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
+ assigned-clock-rates = <1500000>, <1500000>;
+
+ /* Use channel #0 for the system timer channel #2 for the clocksource */
+ ingenic,pwm-channels-mask = <0xfa>;
+};
+
+&uart2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_uart2>;
+};
+
+&pinctrl {
+ pins_uart2: uart2 {
+ function = "uart2";
+ groups = "uart2-data-d";
+ bias-disable;
+ };
+};
diff --git a/arch/mips/configs/cu1000-neo_defconfig b/arch/mips/configs/cu1000-neo_defconfig
new file mode 100644
index 00000000..4fafe92
--- /dev/null
+++ b/arch/mips/configs/cu1000-neo_defconfig
@@ -0,0 +1,98 @@
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_KERNEL_GZIP=y
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_MEMCG=y
+CONFIG_MEMCG_KMEM=y
+CONFIG_CGROUP_SCHED=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE="arch/mips/boot/ramdisk.cpio.gz"
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_INGENIC=y
+CONFIG_X1000_CU1000_NEO=y
+CONFIG_HIGHMEM=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPACTION is not set
+CONFIG_CMA=y
+CONFIG_CMA_AREAS=7
+CONFIG_UEVENT_HELPER=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=2
+CONFIG_SERIAL_EARLYCON=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=3
+CONFIG_SERIAL_8250_RUNTIME_UARTS=3
+CONFIG_SERIAL_8250_INGENIC=y
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+# CONFIG_LCD_CLASS_DEVICE is not set
+# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
+# CONFIG_VGA_CONSOLE is not set
+# CONFIG_HID is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_NVMEM=y
+CONFIG_NVMEM_SYSFS=y
+CONFIG_EXT4_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_PRINTK_TIME=y
+CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
+CONFIG_CONSOLE_LOGLEVEL_QUIET=15
+CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
+CONFIG_DEBUG_INFO=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_PANIC_ON_OOPS=y
+CONFIG_PANIC_TIMEOUT=10
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_STACKTRACE=y
+# CONFIG_FTRACE is not set
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="earlycon clk_ignore_unused"
diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
index 6b96844..412d2fa 100644
--- a/arch/mips/jz4740/Kconfig
+++ b/arch/mips/jz4740/Kconfig
@@ -16,6 +16,10 @@ config JZ4780_CI20
bool "MIPS Creator CI20"
select MACH_JZ4780
+config X1000_CU1000_NEO
+ bool "YSH & ATIL CU1000 Module with Neo backplane"
+ select MACH_X1000
+
endchoice
config MACH_JZ4740
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v6 05/12] MIPS: X1000: Add pdma controller DT node.
2019-11-29 8:48 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Zhou Yanjie
` (3 preceding siblings ...)
2019-11-29 8:48 ` [PATCH v6 04/12] MIPS: Ingenic: Initial YSH & ATIL CU Neo board support Zhou Yanjie
@ 2019-11-29 8:48 ` Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 06/12] MIPS: CU1000: Update defconfig for pdma controller Zhou Yanjie
` (5 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Zhou Yanjie @ 2019-11-29 8:48 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
jhogan, mripard, shawnguo, mark.rutland, syq, ralf, heiko,
icenowy, laurent.pinchart, krzk, geert+renesas, paul,
prasannatsmkumar, sernia.zhou, zhenwenjin, 772753199
Add the appropriate DT node to probe the pdma controller driver
using the devicetree.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
Notes:
v4:
New patch.
v4->v5:
No change.
v5->v6:
No change.
arch/mips/boot/dts/ingenic/x1000.dtsi | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi b/arch/mips/boot/dts/ingenic/x1000.dtsi
index 13a6c9ff..c432828 100644
--- a/arch/mips/boot/dts/ingenic/x1000.dtsi
+++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
@@ -1,5 +1,6 @@
// SPDX-License-Identifier: GPL-2.0
#include <dt-bindings/clock/x1000-cgu.h>
+#include <dt-bindings/dma/x1000-dma.h>
/ {
#address-cells = <1>;
@@ -173,4 +174,16 @@
status = "disabled";
};
+
+ pdma: dma-controller@13420000 {
+ compatible = "ingenic,x1000-dma";
+ reg = <0x13420000 0x400
+ 0x13421000 0x40>;
+ #dma-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <10>;
+
+ clocks = <&cgu X1000_CLK_PDMA>;
+ };
};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v6 06/12] MIPS: CU1000: Update defconfig for pdma controller.
2019-11-29 8:48 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Zhou Yanjie
` (4 preceding siblings ...)
2019-11-29 8:48 ` [PATCH v6 05/12] MIPS: X1000: Add pdma controller DT node Zhou Yanjie
@ 2019-11-29 8:48 ` Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 07/12] MIPS: X1000: Add msc controller DT node Zhou Yanjie
` (4 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Zhou Yanjie @ 2019-11-29 8:48 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
jhogan, mripard, shawnguo, mark.rutland, syq, ralf, heiko,
icenowy, laurent.pinchart, krzk, geert+renesas, paul,
prasannatsmkumar, sernia.zhou, zhenwenjin, 772753199
Selected pdma controller support by default.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
Notes:
v4:
New patch.
v4->v5:
No change.
v5->v6:
No change.
arch/mips/configs/cu1000-neo_defconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/mips/configs/cu1000-neo_defconfig b/arch/mips/configs/cu1000-neo_defconfig
index 4fafe92..6ac51ec 100644
--- a/arch/mips/configs/cu1000-neo_defconfig
+++ b/arch/mips/configs/cu1000-neo_defconfig
@@ -61,6 +61,8 @@ CONFIG_GPIO_SYSFS=y
# CONFIG_VGA_CONSOLE is not set
# CONFIG_HID is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_DMADEVICES=y
+CONFIG_DMA_JZ4780=y
# CONFIG_IOMMU_SUPPORT is not set
CONFIG_NVMEM=y
CONFIG_NVMEM_SYSFS=y
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v6 07/12] MIPS: X1000: Add msc controller DT node.
2019-11-29 8:48 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Zhou Yanjie
` (5 preceding siblings ...)
2019-11-29 8:48 ` [PATCH v6 06/12] MIPS: CU1000: Update defconfig for pdma controller Zhou Yanjie
@ 2019-11-29 8:48 ` Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 08/12] MIPS: CU1000: Update defconfig for msc controller Zhou Yanjie
` (3 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Zhou Yanjie @ 2019-11-29 8:48 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
jhogan, mripard, shawnguo, mark.rutland, syq, ralf, heiko,
icenowy, laurent.pinchart, krzk, geert+renesas, paul,
prasannatsmkumar, sernia.zhou, zhenwenjin, 772753199
Add the appropriate DT node to probe the msc controller driver
using the devicetree.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
Notes:
v5:
New patch.
v5->v6:
No change.
arch/mips/boot/dts/ingenic/cu1000-neo.dts | 16 ++++++++++++
arch/mips/boot/dts/ingenic/x1000.dtsi | 42 +++++++++++++++++++++++++++++++
2 files changed, 58 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
index fb00439..195b266 100644
--- a/arch/mips/boot/dts/ingenic/cu1000-neo.dts
+++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
@@ -43,10 +43,26 @@
pinctrl-0 = <&pins_uart2>;
};
+&msc0 {
+ status = "okay";
+
+ bus-width = <8>;
+ max-frequency = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_msc0>;
+};
+
&pinctrl {
pins_uart2: uart2 {
function = "uart2";
groups = "uart2-data-d";
bias-disable;
};
+
+ pins_msc0: msc0 {
+ function = "mmc0";
+ groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit";
+ bias-disable;
+ };
};
diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi b/arch/mips/boot/dts/ingenic/x1000.dtsi
index c432828..8b8d335 100644
--- a/arch/mips/boot/dts/ingenic/x1000.dtsi
+++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
@@ -186,4 +186,46 @@
clocks = <&cgu X1000_CLK_PDMA>;
};
+
+ msc0: msc@13450000 {
+ compatible = "ingenic,x1000-mmc";
+ reg = <0x13450000 0x1000>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <37>;
+
+ clocks = <&cgu X1000_CLK_MSC0>;
+ clock-names = "mmc";
+
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ cap-sdio-irq;
+
+ dmas = <&pdma X1000_DMA_MSC0_RX 0xffffffff>,
+ <&pdma X1000_DMA_MSC0_TX 0xffffffff>;
+ dma-names = "rx", "tx";
+
+ status = "disabled";
+ };
+
+ msc1: msc@13460000 {
+ compatible = "ingenic,x1000-mmc";
+ reg = <0x13460000 0x1000>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <36>;
+
+ clocks = <&cgu X1000_CLK_MSC1>;
+ clock-names = "mmc";
+
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ cap-sdio-irq;
+
+ dmas = <&pdma X1000_DMA_MSC1_RX 0xffffffff>,
+ <&pdma X1000_DMA_MSC1_TX 0xffffffff>;
+ dma-names = "rx", "tx";
+
+ status = "disabled";
+ };
};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v6 08/12] MIPS: CU1000: Update defconfig for msc controller.
2019-11-29 8:48 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Zhou Yanjie
` (6 preceding siblings ...)
2019-11-29 8:48 ` [PATCH v6 07/12] MIPS: X1000: Add msc controller DT node Zhou Yanjie
@ 2019-11-29 8:48 ` Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 09/12] MIPS: X1000: Add rtc DT node Zhou Yanjie
` (2 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Zhou Yanjie @ 2019-11-29 8:48 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
jhogan, mripard, shawnguo, mark.rutland, syq, ralf, heiko,
icenowy, laurent.pinchart, krzk, geert+renesas, paul,
prasannatsmkumar, sernia.zhou, zhenwenjin, 772753199
Selected msc controller support by default.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
Notes:
v5:
New patch.
v5->v6:
No change.
arch/mips/configs/cu1000-neo_defconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/mips/configs/cu1000-neo_defconfig b/arch/mips/configs/cu1000-neo_defconfig
index 6ac51ec..eef0c5a 100644
--- a/arch/mips/configs/cu1000-neo_defconfig
+++ b/arch/mips/configs/cu1000-neo_defconfig
@@ -61,6 +61,8 @@ CONFIG_GPIO_SYSFS=y
# CONFIG_VGA_CONSOLE is not set
# CONFIG_HID is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+CONFIG_MMC_JZ4740=y
CONFIG_DMADEVICES=y
CONFIG_DMA_JZ4780=y
# CONFIG_IOMMU_SUPPORT is not set
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v6 09/12] MIPS: X1000: Add rtc DT node.
2019-11-29 8:48 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Zhou Yanjie
` (7 preceding siblings ...)
2019-11-29 8:48 ` [PATCH v6 08/12] MIPS: CU1000: Update defconfig for msc controller Zhou Yanjie
@ 2019-11-29 8:48 ` Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 10/12] MIPS: CU1000: Update defconfig for rtc Zhou Yanjie
2019-11-29 11:15 ` Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Paul Cercueil
10 siblings, 0 replies; 12+ messages in thread
From: Zhou Yanjie @ 2019-11-29 8:48 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
jhogan, mripard, shawnguo, mark.rutland, syq, ralf, heiko,
icenowy, laurent.pinchart, krzk, geert+renesas, paul,
prasannatsmkumar, sernia.zhou, zhenwenjin, 772753199
Add the appropriate DT node to probe the rtc driver
using the devicetree.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
Notes:
v5:
New patch.
v5->v6:
No change.
arch/mips/boot/dts/ingenic/x1000.dtsi | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi b/arch/mips/boot/dts/ingenic/x1000.dtsi
index 8b8d335..2a0810b 100644
--- a/arch/mips/boot/dts/ingenic/x1000.dtsi
+++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
@@ -69,6 +69,17 @@
interrupts = <27 26 25>;
};
+ rtc: rtc@10003000 {
+ compatible = "ingenic,x1000-rtc", "ingenic,jz4780-rtc";
+ reg = <0x10003000 0x4c>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <32>;
+
+ clocks = <&cgu X1000_CLK_RTCLK>;
+ clock-names = "rtc";
+ };
+
pinctrl: pin-controller@10010000 {
compatible = "ingenic,x1000-pinctrl";
reg = <0x10010000 0x800>;
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v6 10/12] MIPS: CU1000: Update defconfig for rtc.
2019-11-29 8:48 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Zhou Yanjie
` (8 preceding siblings ...)
2019-11-29 8:48 ` [PATCH v6 09/12] MIPS: X1000: Add rtc DT node Zhou Yanjie
@ 2019-11-29 8:48 ` Zhou Yanjie
2019-11-29 11:15 ` Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Paul Cercueil
10 siblings, 0 replies; 12+ messages in thread
From: Zhou Yanjie @ 2019-11-29 8:48 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
jhogan, mripard, shawnguo, mark.rutland, syq, ralf, heiko,
icenowy, laurent.pinchart, krzk, geert+renesas, paul,
prasannatsmkumar, sernia.zhou, zhenwenjin, 772753199
Selected rtc support by default.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
Notes:
v5:
New patch.
v5->v6:
No change.
arch/mips/configs/cu1000-neo_defconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/mips/configs/cu1000-neo_defconfig b/arch/mips/configs/cu1000-neo_defconfig
index eef0c5a..b2c090a 100644
--- a/arch/mips/configs/cu1000-neo_defconfig
+++ b/arch/mips/configs/cu1000-neo_defconfig
@@ -63,6 +63,8 @@ CONFIG_GPIO_SYSFS=y
# CONFIG_USB_SUPPORT is not set
CONFIG_MMC=y
CONFIG_MMC_JZ4740=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_JZ4740=y
CONFIG_DMADEVICES=y
CONFIG_DMA_JZ4780=y
# CONFIG_IOMMU_SUPPORT is not set
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6.
2019-11-29 8:48 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Zhou Yanjie
` (9 preceding siblings ...)
2019-11-29 8:48 ` [PATCH v6 10/12] MIPS: CU1000: Update defconfig for rtc Zhou Yanjie
@ 2019-11-29 11:15 ` Paul Cercueil
10 siblings, 0 replies; 12+ messages in thread
From: Paul Cercueil @ 2019-11-29 11:15 UTC (permalink / raw)
To: Zhou Yanjie
Cc: linux-mips, linux-kernel, devicetree, robh+dt, paul.burton,
paulburton, jhogan, mripard, shawnguo, mark.rutland, syq, ralf,
heiko, icenowy, laurent.pinchart, krzk, geert+renesas,
prasannatsmkumar, sernia.zhou, zhenwenjin, 772753199
Hi Zhou,
This series need some reorder.
You introduce the defconfig in patch [03/12], then modify it in
[06/12], [08/12] and [10/12]. This just makes the patchset hard to
review and less likely to be merged.
Simply:
- Add missing X1000 nodes (pdma, mmc, rtc) in one patch,
- then add the CU Neo devicetree & config with PDMA, MMC and RTC
enabled.
And where are patches [11/12] and [12/12]? I didn't receive them.
Cheers,
-Paul
Le ven., nov. 29, 2019 at 16:48, Zhou Yanjie <zhouyanjie@zoho.com> a
écrit :
> v5->v6:
> 1.Use "stdout-path = "serial2:115200n8"" instead "stdout-path =
> &uart2" in DT.
> 2.Remove "console=ttyS2,115200n8" and "CONFIG_CMDLINE_OVERRIDE=y"
> from defconfg.
> 3.Add watchdog timer DT node, and update defconfig for watchdog timer.
>
>
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2019-11-29 11:15 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-11-29 8:48 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 01/12] MIPS: Ingenic: Initial X1000 support Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 02/12] dt-bindings: Document yna vendor-prefix Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 03/12] dt-bindings: MIPS: Add Ingenic XBurst based boards Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 04/12] MIPS: Ingenic: Initial YSH & ATIL CU Neo board support Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 05/12] MIPS: X1000: Add pdma controller DT node Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 06/12] MIPS: CU1000: Update defconfig for pdma controller Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 07/12] MIPS: X1000: Add msc controller DT node Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 08/12] MIPS: CU1000: Update defconfig for msc controller Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 09/12] MIPS: X1000: Add rtc DT node Zhou Yanjie
2019-11-29 8:48 ` [PATCH v6 10/12] MIPS: CU1000: Update defconfig for rtc Zhou Yanjie
2019-11-29 11:15 ` Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v6 Paul Cercueil
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).