[PATCH v8 0/7] mt8183 dpi supports dual edge and pin mode swap

[PATCH v8 0/7] mt8183 dpi supports dual edge and pin mode swap

[Jitao Shi]

Changes since v7:
 - separate dt-bindings to independent patches.
 - move dpi dual edge to one patch.

Changes since v6:
 - change dual_edge to pclk-sample
 - remove dpi_pin_mode_swap and

Changes since v5:
 - fine tune the dt-bindings commit message.

Changes since v4:
 - move pin mode control and dual edge control to deveice tree.
 - update dt-bindings document for pin mode swap and dual edge control.

Changes since v3:
 - add dpi pin mode control when dpi on or off.
 - update dpi dual edge comment.

Changes since v2:
 - update dt-bindings document for mt8183 dpi.
 - separate dual edge modfication as independent patch.

Jitao Shi (7):
  dt-bindings: media: add pclk-sample dual edge property
  dt-bindings: display: mediatek: update dpi supported chips
  dt-bindings: display: mediatek: control dpi pins mode to avoid leakage
  dt-bindings: display: mediatek: dpi sample data in dual edge support
  drm/mediatek: dpi sample mode support
  drm/mediatek: add mt8183 dpi clock factor
  drm/mediatek: set dpi pin mode to gpio low to avoid leakage current

 .../display/mediatek/mediatek,dpi.txt         | 12 ++++
 .../bindings/media/video-interfaces.txt       |  4 +-
 drivers/gpu/drm/mediatek/mtk_dpi.c            | 66 ++++++++++++++++++-
 3 files changed, 78 insertions(+), 4 deletions(-)

-- 
2.21.0

[PATCH v8 1/7] dt-bindings: media: add pclk-sample dual edge property

[Jitao Shi]

Some chips's sample mode are rising, falling and dual edge (both
falling and rising edge).
Extern the pclk-sample property to support dual edge.

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 Documentation/devicetree/bindings/media/video-interfaces.txt | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt
index f884ada0bffc..da9ad24935db 100644
--- a/Documentation/devicetree/bindings/media/video-interfaces.txt
+++ b/Documentation/devicetree/bindings/media/video-interfaces.txt
@@ -118,8 +118,8 @@ Optional endpoint properties
 - data-enable-active: similar to HSYNC and VSYNC, specifies the data enable
   signal polarity.
 - field-even-active: field signal level during the even field data transmission.
-- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
-  signal.
+- pclk-sample: sample data on rising (1), falling (0) or both rising and
+  falling (2) edge of the pixel clock signal.
 - sync-on-green-active: active state of Sync-on-green (SoG) signal, 0/1 for
   LOW/HIGH respectively.
 - data-lanes: an array of physical data lane indexes. Position of an entry
-- 
2.21.0

[PATCH v8 2/7] dt-bindings: display: mediatek: update dpi supported chips

[Jitao Shi]

Add descriptions about supported chips, including MT2701 & MT8173 &
mt8183

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 .../devicetree/bindings/display/mediatek/mediatek,dpi.txt        | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
index b6a7e7397b8b..58914cf681b8 100644
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
@@ -7,6 +7,7 @@ output bus.
 
 Required properties:
 - compatible: "mediatek,<chip>-dpi"
+  the supported chips are mt2701 , mt8173 and mt8183.
 - reg: Physical base address and length of the controller's registers
 - interrupts: The interrupt signal from the function block.
 - clocks: device clocks
-- 
2.21.0

[PATCH v8 3/7] dt-bindings: display: mediatek: control dpi pins mode to avoid leakage

[Jitao Shi]

Add property "pinctrl-names" to swap pin mode between gpio and dpi mode. Set
pin mode to gpio oupput-low to avoid leakage current when dpi disable.

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 .../devicetree/bindings/display/mediatek/mediatek,dpi.txt  | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
index 58914cf681b8..a7b1b8bfb65e 100644
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
@@ -17,6 +17,10 @@ Required properties:
   Documentation/devicetree/bindings/graph.txt. This port should be connected
   to the input port of an attached HDMI or LVDS encoder chip.
 
+Optional properties:
+- pinctrl-names: Contain "gpiomode" and "dpimode".
+  pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
+
 Example:
 
 dpi0: dpi@1401d000 {
@@ -27,6 +31,9 @@ dpi0: dpi@1401d000 {
 		 <&mmsys CLK_MM_DPI_ENGINE>,
 		 <&apmixedsys CLK_APMIXED_TVDPLL>;
 	clock-names = "pixel", "engine", "pll";
+	pinctrl-names = "gpiomode", "dpimode";
+	pinctrl-0 = <&dpi_pin_gpio>;
+	pinctrl-1 = <&dpi_pin_func>;
 
 	port {
 		dpi0_out: endpoint {
-- 
2.21.0

[PATCH v8 4/7] dt-bindings: display: mediatek: dpi sample data in dual edge support

[Jitao Shi]

Add property "pclk-sample" to config the dpi sample on falling (0),
rising (1), both falling and rising (2).

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 .../devicetree/bindings/display/mediatek/mediatek,dpi.txt     | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
index a7b1b8bfb65e..f362fff51437 100644
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
@@ -20,6 +20,9 @@ Required properties:
 Optional properties:
 - pinctrl-names: Contain "gpiomode" and "dpimode".
   pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
+- pclk-sample: 0: sample in falling edge, 1: sample in rising edge, 2: sample
+  in both falling and rising edge.
+  pclk-sample see Documentation/devicetree/bindings/media/video-interfaces.txt.
 
 Example:
 
@@ -37,6 +40,7 @@ dpi0: dpi@1401d000 {
 
 	port {
 		dpi0_out: endpoint {
+			pclk-sample = 0;
 			remote-endpoint = <&hdmi0_in>;
 		};
 	};
-- 
2.21.0

[PATCH v8 5/7] drm/mediatek: dpi sample mode support

[Jitao Shi]

DPI can sample on falling, rising or both edge.
When DPI sample the data both rising and falling edge.
It can reduce half data io pins.

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dpi.c | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
index 01fa8b8d763d..df598f87a40f 100644
--- a/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -75,6 +75,7 @@ struct mtk_dpi {
 	enum mtk_dpi_out_bit_num bit_num;
 	enum mtk_dpi_out_channel_swap channel_swap;
 	int refcount;
+	u32 pclk_sample;
 };
 
 static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
@@ -348,6 +349,13 @@ static void mtk_dpi_config_disable_edge(struct mtk_dpi *dpi)
 		mtk_dpi_mask(dpi, dpi->conf->reg_h_fre_con, 0, EDGE_SEL_EN);
 }
 
+static void mtk_dpi_enable_pclk_sample_dual_edge(struct mtk_dpi *dpi)
+{
+	mtk_dpi_mask(dpi, DPI_DDR_SETTING, DDR_EN | DDR_4PHASE,
+		     DDR_EN | DDR_4PHASE);
+	mtk_dpi_mask(dpi, DPI_OUTPUT_SETTING, EDGE_SEL, EDGE_SEL);
+}
+
 static void mtk_dpi_config_color_format(struct mtk_dpi *dpi,
 					enum mtk_dpi_out_color_format format)
 {
@@ -439,7 +447,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
 	pll_rate = clk_get_rate(dpi->tvd_clk);
 
 	vm.pixelclock = pll_rate / factor;
-	clk_set_rate(dpi->pixel_clk, vm.pixelclock);
+	clk_set_rate(dpi->pixel_clk,
+		     vm.pixelclock * (dpi->pclk_sample > 1 ? 2 : 1));
 	vm.pixelclock = clk_get_rate(dpi->pixel_clk);
 
 	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
@@ -450,7 +459,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
 	limit.y_bottom = 0x0010;
 	limit.y_top = 0x0FE0;
 
-	dpi_pol.ck_pol = MTK_DPI_POLARITY_FALLING;
+	dpi_pol.ck_pol = dpi->pclk_sample == 1 ?
+			 MTK_DPI_POLARITY_RISING : MTK_DPI_POLARITY_FALLING;
 	dpi_pol.de_pol = MTK_DPI_POLARITY_RISING;
 	dpi_pol.hsync_pol = vm.flags & DISPLAY_FLAGS_HSYNC_HIGH ?
 			    MTK_DPI_POLARITY_FALLING : MTK_DPI_POLARITY_RISING;
@@ -504,6 +514,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
 	mtk_dpi_config_color_format(dpi, dpi->color_format);
 	mtk_dpi_config_2n_h_fre(dpi);
 	mtk_dpi_config_disable_edge(dpi);
+	if (dpi->pclk_sample > 1)
+		mtk_dpi_enable_pclk_sample_dual_edge(dpi);
 	mtk_dpi_sw_reset(dpi, false);
 
 	return 0;
@@ -689,6 +701,8 @@ static int mtk_dpi_probe(struct platform_device *pdev)
 
 	dpi->dev = dev;
 	dpi->conf = (struct mtk_dpi_conf *)of_device_get_match_data(dev);
+	of_property_read_u32_index(dev->of_node, "pclk-sample", 1,
+				   &dpi->pclk_sample);
 
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dpi->regs = devm_ioremap_resource(dev, mem);
-- 
2.21.0

[PATCH v8 6/7] drm/mediatek: add mt8183 dpi clock factor

[Jitao Shi]

The factor depends on the divider of DPI in MT8183, therefore,
we should fix this factor to the right and new one.

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dpi.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
index df598f87a40f..db3272f7a4c4 100644
--- a/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -676,6 +676,16 @@ static unsigned int mt2701_calculate_factor(int clock)
 		return 1;
 }
 
+static unsigned int mt8183_calculate_factor(int clock)
+{
+	if (clock <= 27000)
+		return 8;
+	else if (clock <= 167000)
+		return 4;
+	else
+		return 2;
+}
+
 static const struct mtk_dpi_conf mt8173_conf = {
 	.cal_factor = mt8173_calculate_factor,
 	.reg_h_fre_con = 0xe0,
@@ -687,6 +697,11 @@ static const struct mtk_dpi_conf mt2701_conf = {
 	.edge_sel_en = true,
 };
 
+static const struct mtk_dpi_conf mt8183_conf = {
+	.cal_factor = mt8183_calculate_factor,
+	.reg_h_fre_con = 0xe0,
+};
+
 static int mtk_dpi_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -784,6 +799,9 @@ static const struct of_device_id mtk_dpi_of_ids[] = {
 	{ .compatible = "mediatek,mt8173-dpi",
 	  .data = &mt8173_conf,
 	},
+	{ .compatible = "mediatek,mt8183-dpi",
+	  .data = &mt8183_conf,
+	},
 	{ },
 };
 
-- 
2.21.0

[PATCH v8 7/7] drm/mediatek: set dpi pin mode to gpio low to avoid leakage current

[Jitao Shi]

Config dpi pins mode to output and pull low when dpi is disabled.
Aovid leakage current from some dpi pins (Hsync Vsync DE ... ).

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dpi.c | 30 ++++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
index db3272f7a4c4..d6a570c03ee9 100644
--- a/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -10,7 +10,9 @@
 #include <linux/kernel.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_gpio.h>
 #include <linux/of_graph.h>
+#include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/types.h>
 
@@ -74,6 +76,9 @@ struct mtk_dpi {
 	enum mtk_dpi_out_yc_map yc_map;
 	enum mtk_dpi_out_bit_num bit_num;
 	enum mtk_dpi_out_channel_swap channel_swap;
+	struct pinctrl *pinctrl;
+	struct pinctrl_state *pins_gpio;
+	struct pinctrl_state *pins_dpi;
 	int refcount;
 	u32 pclk_sample;
 };
@@ -387,6 +392,9 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi)
 	if (--dpi->refcount != 0)
 		return;
 
+	if (dpi->pinctrl && dpi->pins_gpio)
+		pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
+
 	mtk_dpi_disable(dpi);
 	clk_disable_unprepare(dpi->pixel_clk);
 	clk_disable_unprepare(dpi->engine_clk);
@@ -411,6 +419,9 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi)
 		goto err_pixel;
 	}
 
+	if (dpi->pinctrl && dpi->pins_dpi)
+		pinctrl_select_state(dpi->pinctrl, dpi->pins_dpi);
+
 	mtk_dpi_enable(dpi);
 	return 0;
 
@@ -719,6 +730,25 @@ static int mtk_dpi_probe(struct platform_device *pdev)
 	of_property_read_u32_index(dev->of_node, "pclk-sample", 1,
 				   &dpi->pclk_sample);
 
+	dpi->pinctrl = devm_pinctrl_get(&pdev->dev);
+	if (IS_ERR(dpi->pinctrl)) {
+		dpi->pinctrl = NULL;
+		dev_dbg(&pdev->dev, "Cannot find pinctrl!\n");
+	}
+	dpi->pins_gpio = pinctrl_lookup_state(dpi->pinctrl, "gpiomode");
+	if (IS_ERR(dpi->pins_gpio)) {
+		dpi->pins_gpio = NULL;
+		dev_dbg(&pdev->dev, "Cannot find pinctrl gpiomode!\n");
+	}
+	if (dpi->pinctrl && dpi->pins_gpio)
+		pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
+
+	dpi->pins_dpi = pinctrl_lookup_state(dpi->pinctrl, "dpimode");
+	if (IS_ERR(dpi->pins_dpi)) {
+		dpi->pins_dpi = NULL;
+		dev_dbg(&pdev->dev, "Cannot find pinctrl dpimode!\n");
+	}
+
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dpi->regs = devm_ioremap_resource(dev, mem);
 	if (IS_ERR(dpi->regs)) {
-- 
2.21.0

Re: [PATCH v8 2/7] dt-bindings: display: mediatek: update dpi supported chips

[Rob Herring]

On Tue, 25 Feb 2020 17:40:52 +0800, Jitao Shi wrote:
> Add descriptions about supported chips, including MT2701 & MT8173 &
> mt8183
> 
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  .../devicetree/bindings/display/mediatek/mediatek,dpi.txt        | 1 +
>  1 file changed, 1 insertion(+)
> 

Please add Acked-by/Reviewed-by tags when posting new versions. However,
there's no need to repost patches *only* to add the tags. The upstream
maintainer will do that for acks received on the version they apply.

If a tag was not added on purpose, please state why and what changed.

Re: [PATCH v8 2/7] dt-bindings: display: mediatek: update dpi supported chips

[CK Hu]

On Tue, 2020-02-25 at 11:10 -0600, Rob Herring wrote:
> On Tue, 25 Feb 2020 17:40:52 +0800, Jitao Shi wrote:
> > Add descriptions about supported chips, including MT2701 & MT8173 &
> > mt8183
> > 
> > Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> > ---
> >  .../devicetree/bindings/display/mediatek/mediatek,dpi.txt        | 1 +
> >  1 file changed, 1 insertion(+)
> > 
> 
> Please add Acked-by/Reviewed-by tags when posting new versions. However,
> there's no need to repost patches *only* to add the tags. The upstream
> maintainer will do that for acks received on the version they apply.
> 
> If a tag was not added on purpose, please state why and what changed.

I think this version is the same as v3 [1] which has been reviewed by
Rob, so I applied this patch i mediatek-drm-next-5.7 [2], thanks.

[1] https://patchwork.kernel.org/patch/10901971/
[2]
https://github.com/ckhu-mediatek/linux.git-tags/commits/mediatek-drm-next-5.7

Regards,
CK

Re: [PATCH v8 6/7] drm/mediatek: add mt8183 dpi clock factor

[CK Hu]

Hi, Jitao:

On Tue, 2020-02-25 at 17:40 +0800, Jitao Shi wrote:
> The factor depends on the divider of DPI in MT8183, therefore,
> we should fix this factor to the right and new one.
> 

Applied to mediatek-drm-next-5.7 [1], thanks.

[1]
https://github.com/ckhu-mediatek/linux.git-tags/commits/mediatek-drm-next-5.7

> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> Reviewed-by: CK Hu <ck.hu@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dpi.c | 18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> index df598f87a40f..db3272f7a4c4 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> @@ -676,6 +676,16 @@ static unsigned int mt2701_calculate_factor(int clock)
>  		return 1;
>  }
>  
> +static unsigned int mt8183_calculate_factor(int clock)
> +{
> +	if (clock <= 27000)
> +		return 8;
> +	else if (clock <= 167000)
> +		return 4;
> +	else
> +		return 2;
> +}
> +
>  static const struct mtk_dpi_conf mt8173_conf = {
>  	.cal_factor = mt8173_calculate_factor,
>  	.reg_h_fre_con = 0xe0,
> @@ -687,6 +697,11 @@ static const struct mtk_dpi_conf mt2701_conf = {
>  	.edge_sel_en = true,
>  };
>  
> +static const struct mtk_dpi_conf mt8183_conf = {
> +	.cal_factor = mt8183_calculate_factor,
> +	.reg_h_fre_con = 0xe0,
> +};
> +
>  static int mtk_dpi_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
> @@ -784,6 +799,9 @@ static const struct of_device_id mtk_dpi_of_ids[] = {
>  	{ .compatible = "mediatek,mt8173-dpi",
>  	  .data = &mt8173_conf,
>  	},
> +	{ .compatible = "mediatek,mt8183-dpi",
> +	  .data = &mt8183_conf,
> +	},
>  	{ },
>  };
>  

Re: [PATCH v8 1/7] dt-bindings: media: add pclk-sample dual edge property

[CK Hu]

On Tue, 2020-02-25 at 17:40 +0800, Jitao Shi wrote:
> Some chips's sample mode are rising, falling and dual edge (both
> falling and rising edge).
> Extern the pclk-sample property to support dual edge.
> 

Reviewed-by: CK Hu <ck.hu@mediatek.com>

> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  Documentation/devicetree/bindings/media/video-interfaces.txt | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt
> index f884ada0bffc..da9ad24935db 100644
> --- a/Documentation/devicetree/bindings/media/video-interfaces.txt
> +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt
> @@ -118,8 +118,8 @@ Optional endpoint properties
>  - data-enable-active: similar to HSYNC and VSYNC, specifies the data enable
>    signal polarity.
>  - field-even-active: field signal level during the even field data transmission.
> -- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
> -  signal.
> +- pclk-sample: sample data on rising (1), falling (0) or both rising and
> +  falling (2) edge of the pixel clock signal.
>  - sync-on-green-active: active state of Sync-on-green (SoG) signal, 0/1 for
>    LOW/HIGH respectively.
>  - data-lanes: an array of physical data lane indexes. Position of an entry

Re: [PATCH v8 3/7] dt-bindings: display: mediatek: control dpi pins mode to avoid leakage

[CK Hu]

On Tue, 2020-02-25 at 17:40 +0800, Jitao Shi wrote:
> Add property "pinctrl-names" to swap pin mode between gpio and dpi mode. Set
> pin mode to gpio oupput-low to avoid leakage current when dpi disable.
> 

Reviewed-by: CK Hu <ck.hu@mediatek.com>

> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  .../devicetree/bindings/display/mediatek/mediatek,dpi.txt  | 7 +++++++
>  1 file changed, 7 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> index 58914cf681b8..a7b1b8bfb65e 100644
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> @@ -17,6 +17,10 @@ Required properties:
>    Documentation/devicetree/bindings/graph.txt. This port should be connected
>    to the input port of an attached HDMI or LVDS encoder chip.
>  
> +Optional properties:
> +- pinctrl-names: Contain "gpiomode" and "dpimode".
> +  pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
> +
>  Example:
>  
>  dpi0: dpi@1401d000 {
> @@ -27,6 +31,9 @@ dpi0: dpi@1401d000 {
>  		 <&mmsys CLK_MM_DPI_ENGINE>,
>  		 <&apmixedsys CLK_APMIXED_TVDPLL>;
>  	clock-names = "pixel", "engine", "pll";
> +	pinctrl-names = "gpiomode", "dpimode";
> +	pinctrl-0 = <&dpi_pin_gpio>;
> +	pinctrl-1 = <&dpi_pin_func>;
>  
>  	port {
>  		dpi0_out: endpoint {

Re: [PATCH v8 4/7] dt-bindings: display: mediatek: dpi sample data in dual edge support

[CK Hu]

Hi, Jitao:

On Tue, 2020-02-25 at 17:40 +0800, Jitao Shi wrote:
> Add property "pclk-sample" to config the dpi sample on falling (0),
> rising (1), both falling and rising (2).
> 
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  .../devicetree/bindings/display/mediatek/mediatek,dpi.txt     | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> index a7b1b8bfb65e..f362fff51437 100644
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> @@ -20,6 +20,9 @@ Required properties:
>  Optional properties:
>  - pinctrl-names: Contain "gpiomode" and "dpimode".
>    pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
> +- pclk-sample: 0: sample in falling edge, 1: sample in rising edge, 2: sample
> +  in both falling and rising edge.

The value has been defined in video-interfaces.txt, you need not to
define it again.

Regards,
CK

> +  pclk-sample see Documentation/devicetree/bindings/media/video-interfaces.txt.
>  
>  Example:
>  
> @@ -37,6 +40,7 @@ dpi0: dpi@1401d000 {
>  
>  	port {
>  		dpi0_out: endpoint {
> +			pclk-sample = 0;
>  			remote-endpoint = <&hdmi0_in>;
>  		};
>  	};

Re: [PATCH v8 5/7] drm/mediatek: dpi sample mode support

[CK Hu]

On Tue, 2020-02-25 at 17:40 +0800, Jitao Shi wrote:
> DPI can sample on falling, rising or both edge.
> When DPI sample the data both rising and falling edge.
> It can reduce half data io pins.
> 

Reviewed-by: CK Hu <ck.hu@mediatek.com>

> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dpi.c | 18 ++++++++++++++++--
>  1 file changed, 16 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> index 01fa8b8d763d..df598f87a40f 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> @@ -75,6 +75,7 @@ struct mtk_dpi {
>  	enum mtk_dpi_out_bit_num bit_num;
>  	enum mtk_dpi_out_channel_swap channel_swap;
>  	int refcount;
> +	u32 pclk_sample;
>  };
>  
>  static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
> @@ -348,6 +349,13 @@ static void mtk_dpi_config_disable_edge(struct mtk_dpi *dpi)
>  		mtk_dpi_mask(dpi, dpi->conf->reg_h_fre_con, 0, EDGE_SEL_EN);
>  }
>  
> +static void mtk_dpi_enable_pclk_sample_dual_edge(struct mtk_dpi *dpi)
> +{
> +	mtk_dpi_mask(dpi, DPI_DDR_SETTING, DDR_EN | DDR_4PHASE,
> +		     DDR_EN | DDR_4PHASE);
> +	mtk_dpi_mask(dpi, DPI_OUTPUT_SETTING, EDGE_SEL, EDGE_SEL);
> +}
> +
>  static void mtk_dpi_config_color_format(struct mtk_dpi *dpi,
>  					enum mtk_dpi_out_color_format format)
>  {
> @@ -439,7 +447,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
>  	pll_rate = clk_get_rate(dpi->tvd_clk);
>  
>  	vm.pixelclock = pll_rate / factor;
> -	clk_set_rate(dpi->pixel_clk, vm.pixelclock);
> +	clk_set_rate(dpi->pixel_clk,
> +		     vm.pixelclock * (dpi->pclk_sample > 1 ? 2 : 1));
>  	vm.pixelclock = clk_get_rate(dpi->pixel_clk);
>  
>  	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> @@ -450,7 +459,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
>  	limit.y_bottom = 0x0010;
>  	limit.y_top = 0x0FE0;
>  
> -	dpi_pol.ck_pol = MTK_DPI_POLARITY_FALLING;
> +	dpi_pol.ck_pol = dpi->pclk_sample == 1 ?
> +			 MTK_DPI_POLARITY_RISING : MTK_DPI_POLARITY_FALLING;
>  	dpi_pol.de_pol = MTK_DPI_POLARITY_RISING;
>  	dpi_pol.hsync_pol = vm.flags & DISPLAY_FLAGS_HSYNC_HIGH ?
>  			    MTK_DPI_POLARITY_FALLING : MTK_DPI_POLARITY_RISING;
> @@ -504,6 +514,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
>  	mtk_dpi_config_color_format(dpi, dpi->color_format);
>  	mtk_dpi_config_2n_h_fre(dpi);
>  	mtk_dpi_config_disable_edge(dpi);
> +	if (dpi->pclk_sample > 1)
> +		mtk_dpi_enable_pclk_sample_dual_edge(dpi);
>  	mtk_dpi_sw_reset(dpi, false);
>  
>  	return 0;
> @@ -689,6 +701,8 @@ static int mtk_dpi_probe(struct platform_device *pdev)
>  
>  	dpi->dev = dev;
>  	dpi->conf = (struct mtk_dpi_conf *)of_device_get_match_data(dev);
> +	of_property_read_u32_index(dev->of_node, "pclk-sample", 1,
> +				   &dpi->pclk_sample);
>  
>  	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>  	dpi->regs = devm_ioremap_resource(dev, mem);

Re: [PATCH v8 7/7] drm/mediatek: set dpi pin mode to gpio low to avoid leakage current

[CK Hu]

Hi, Jitao:

On Tue, 2020-02-25 at 17:40 +0800, Jitao Shi wrote:
> Config dpi pins mode to output and pull low when dpi is disabled.
> Aovid leakage current from some dpi pins (Hsync Vsync DE ... ).
> 
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dpi.c | 30 ++++++++++++++++++++++++++++++
>  1 file changed, 30 insertions(+)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> index db3272f7a4c4..d6a570c03ee9 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> @@ -10,7 +10,9 @@
>  #include <linux/kernel.h>
>  #include <linux/of.h>
>  #include <linux/of_device.h>
> +#include <linux/of_gpio.h>
>  #include <linux/of_graph.h>
> +#include <linux/pinctrl/consumer.h>
>  #include <linux/platform_device.h>
>  #include <linux/types.h>
>  
> @@ -74,6 +76,9 @@ struct mtk_dpi {
>  	enum mtk_dpi_out_yc_map yc_map;
>  	enum mtk_dpi_out_bit_num bit_num;
>  	enum mtk_dpi_out_channel_swap channel_swap;
> +	struct pinctrl *pinctrl;
> +	struct pinctrl_state *pins_gpio;
> +	struct pinctrl_state *pins_dpi;
>  	int refcount;
>  	u32 pclk_sample;
>  };
> @@ -387,6 +392,9 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi)
>  	if (--dpi->refcount != 0)
>  		return;
>  
> +	if (dpi->pinctrl && dpi->pins_gpio)
> +		pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
> +
>  	mtk_dpi_disable(dpi);
>  	clk_disable_unprepare(dpi->pixel_clk);
>  	clk_disable_unprepare(dpi->engine_clk);
> @@ -411,6 +419,9 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi)
>  		goto err_pixel;
>  	}
>  
> +	if (dpi->pinctrl && dpi->pins_dpi)
> +		pinctrl_select_state(dpi->pinctrl, dpi->pins_dpi);
> +
>  	mtk_dpi_enable(dpi);
>  	return 0;
>  
> @@ -719,6 +730,25 @@ static int mtk_dpi_probe(struct platform_device *pdev)
>  	of_property_read_u32_index(dev->of_node, "pclk-sample", 1,
>  				   &dpi->pclk_sample);
>  
> +	dpi->pinctrl = devm_pinctrl_get(&pdev->dev);
> +	if (IS_ERR(dpi->pinctrl)) {
> +		dpi->pinctrl = NULL;
> +		dev_dbg(&pdev->dev, "Cannot find pinctrl!\n");
> +	}
> +	dpi->pins_gpio = pinctrl_lookup_state(dpi->pinctrl, "gpiomode");

When dpi->pinctrl is NULL, you pass it into pinctrl_lookup_state() would
get something wrong, so call this function only when dpi->pinctrl is not
NULL.

> +	if (IS_ERR(dpi->pins_gpio)) {
> +		dpi->pins_gpio = NULL;
> +		dev_dbg(&pdev->dev, "Cannot find pinctrl gpiomode!\n");
> +	}
> +	if (dpi->pinctrl && dpi->pins_gpio)
> +		pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
> +
> +	dpi->pins_dpi = pinctrl_lookup_state(dpi->pinctrl, "dpimode");

Ditto.

Regards,
CK

> +	if (IS_ERR(dpi->pins_dpi)) {
> +		dpi->pins_dpi = NULL;
> +		dev_dbg(&pdev->dev, "Cannot find pinctrl dpimode!\n");
> +	}
> +
>  	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>  	dpi->regs = devm_ioremap_resource(dev, mem);
>  	if (IS_ERR(dpi->regs)) {