* [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings @ 2020-03-11 9:48 ` Vinay Simha BN 2020-03-11 9:48 ` [PATCH 2/2] display/drm/bridge: tc358775 DSI/LVDS driver Vinay Simha BN ` (3 more replies) 0 siblings, 4 replies; 10+ messages in thread From: Vinay Simha BN @ 2020-03-11 9:48 UTC (permalink / raw) To: Andrzej Hajda, Laurent Pinchart Cc: Vinay Simha BN, David Airlie, Daniel Vetter, Rob Herring, open list:DRM DRIVERS, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, open list Add yaml documentation for DSI/LVDS tc358775 bridge Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> --- v1: Initial version --- .../bindings/display/bridge/toshiba-tc358775.yaml | 174 +++++++++++++++++++++ 1 file changed, 174 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml b/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml new file mode 100644 index 0000000..e9a9544 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml @@ -0,0 +1,174 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/toshiba-tc358775.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + + +title: Toshiba TC358775 DSI to LVDS bridge bindings + +maintainers: + - Vinay Simha BN <simhavcs@gmail.com> + +description: | + This binding supports DSI to LVDS bridge TC358775 + +properties: + compatible: + const: toshiba,tc358775 + + reg: + maxItems: 1 + description: i2c address of the bridge, 0x0f + + tc, dsi-lanes: 1 + maxItems: 1 + description: Number of DSI data lanes connected to the DSI host. It should + be one of 1, 2, 3 or 4. + + tc, dual-link: 1 + maxItems: 1 + description: To configure the LVDS transmitter either as single-link or dual-link. + + vdd-supply: + maxItems: 1 + description: 1.2V LVDS Power Supply + + vddio-supply: + maxItems: 1 + description: 1.8V IO Power Supply + + stby-gpios: + maxItems: 1 + description: Standby pin, Low active + + reset-gpios: + maxItems: 1 + description: Hardware reset, Low active + + ports: + type: object + + properties: + port@0: + type: object + description: | + DSI Input. The remote endpoint phandle should be a + reference to a valid mipi_dsi_host device node. + port@1: + type: object + description: | + Video port for LVDS output (panel or connector). + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - dsi-lanes + - vdd-supply + - vddio-supply + - stby-gpios + - reset-gpios + - ports + +examples: + - | + i2c@78b8000 { + /* On High speed expansion */ + label = "HS-I2C2"; + status = "okay"; + + tc_bridge: bridge@f { + status = "okay"; + + compatible = "toshiba,tc358775"; + reg = <0x0f>; + + tc,dsi-lanes = <4>; + tc,dual-link = <0>; + + vdd-supply = <&pm8916_l2>; + vddio-supply = <&pm8916_l6>; + + stby-gpio = <&msmgpio 99 GPIO_ACTIVE_LOW>; + reset-gpio = <&msmgpio 72 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + d2l_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + d2l_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; + }; + + panel: auo,b101xtn01 { + status = "okay"; + compatible = "auo,b101xtn01", "panel-lvds"; + power-supply = <&pm8916_l14>; + + width-mm = <223>; + height-mm = <125>; + + data-mapping = "jeida-24"; + + panel-timing { + /* 1366x768 @60Hz */ + clock-frequency = <72000000>; + hactive = <1366>; + vactive = <768>; + hsync-len = <70>; + hfront-porch = <20>; + hback-porch = <0>; + vsync-len = <42>; + vfront-porch = <14>; + vback-porch = <0>; + }; + + port { + panel_in: endpoint { + remote-endpoint = <&d2l_out>; + }; + }; + }; + + mdss@1a00000 { + status = "okay"; + + mdp@1a01000 { + status = "okay"; + }; + + dsi@1a98000 { + status = "okay"; + .. + ports { + port@1 { + dsi0_out: endpoint { + remote-endpoint = <&d2l_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; + }; + + dsi-phy@1a98300 { + status = "okay"; + .. + }; + }; -- 2.7.4 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH 2/2] display/drm/bridge: tc358775 DSI/LVDS driver 2020-03-11 9:48 ` [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings Vinay Simha BN @ 2020-03-11 9:48 ` Vinay Simha BN 2020-03-12 10:50 ` Andrzej Hajda 2020-03-12 10:34 ` [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings Andrzej Hajda ` (2 subsequent siblings) 3 siblings, 1 reply; 10+ messages in thread From: Vinay Simha BN @ 2020-03-11 9:48 UTC (permalink / raw) To: Andrzej Hajda, Laurent Pinchart Cc: Vinay Simha BN, Neil Armstrong, Laurent Pinchart, Jonas Karlman, Jernej Skrabec, David Airlie, Daniel Vetter, open list, open list:DRM DRIVERS dsi2lvds tc358775 bridge driver added Tested in apq8016, ifc6309 board and panel auo,b101xtn01 Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> --- v1: Initial version v2: * Andrzej Hajda review comments incorporated SPDX identifier development debug removed alphabetic order headers u32 instead of unit32_t magic numbers to macros for CLRSI and mux registers ignored return value * Laurent Pinchart review comments incorporated mdelay to usleep_range bus_formats added --- drivers/gpu/drm/bridge/Kconfig | 10 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/tc358775.c | 688 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 699 insertions(+) create mode 100644 drivers/gpu/drm/bridge/tc358775.c diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig index 8397bf7..d5528fa 100644 --- a/drivers/gpu/drm/bridge/Kconfig +++ b/drivers/gpu/drm/bridge/Kconfig @@ -133,6 +133,16 @@ config DRM_TOSHIBA_TC358767 ---help--- Toshiba TC358767 eDP bridge chip driver. +config DRM_TOSHIBA_TC358775 + tristate "Toshiba TC358775 LVDS bridge" + depends on OF + select DRM_KMS_HELPER + select REGMAP_I2C + select DRM_PANEL + select DRM_MIPI_DSI + ---help--- + Toshiba TC358775 LVDS bridge chip driver. + config DRM_TI_TFP410 tristate "TI TFP410 DVI/HDMI bridge" depends on OF diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile index 1eb5376..9b2c512 100644 --- a/drivers/gpu/drm/bridge/Makefile +++ b/drivers/gpu/drm/bridge/Makefile @@ -12,6 +12,7 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/ obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c new file mode 100644 index 0000000..28b828e --- /dev/null +++ b/drivers/gpu/drm/bridge/tc358775.c @@ -0,0 +1,688 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * tc358775 DSI to LVDS bridge driver + * + * Copyright (C) 2020 InforceComputing + * Author: Vinay Simha BN <vinaysimha@inforcecomputing.com> + * + */ +#define DEBUG +#include <linux/clk.h> +#include <linux/device.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/regmap.h> +#include <linux/regulator/consumer.h> +#include <linux/slab.h> + +#include <drm/drm_atomic_helper.h> +#include <drm/drm_bridge.h> +#include <drm/drm_crtc_helper.h> +#include <drm/drm_dp_helper.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_of.h> +#include <drm/drm_panel.h> +#include <drm/drm_probe_helper.h> + +#define FLD_MASK(start, end) (((1 << ((start) - (end) + 1)) - 1) << (end)) +#define FLD_VAL(val, start, end) (((val) << (end)) & FLD_MASK(start, end)) + +/* Registers */ + +/* DSI D-PHY Layer Registers */ +#define D0W_DPHYCONTTX 0x0004 /* Data Lane 0 DPHY Tx Control */ +#define CLW_DPHYCONTRX 0x0020 /* Clock Lane DPHY Rx Control */ +#define D0W_DPHYCONTRX 0x0024 /* Data Lane 0 DPHY Rx Control */ +#define D1W_DPHYCONTRX 0x0028 /* Data Lane 1 DPHY Rx Control */ +#define D2W_DPHYCONTRX 0x002C /* Data Lane 2 DPHY Rx Control */ +#define D3W_DPHYCONTRX 0x0030 /* Data Lane 3 DPHY Rx Control */ +#define COM_DPHYCONTRX 0x0038 /* DPHY Rx Common Control */ +#define CLW_CNTRL 0x0040 /* Clock Lane Control */ +#define D0W_CNTRL 0x0044 /* Data Lane 0 Control */ +#define D1W_CNTRL 0x0048 /* Data Lane 1 Control */ +#define D2W_CNTRL 0x004C /* Data Lane 2 Control */ +#define D3W_CNTRL 0x0050 /* Data Lane 3 Control */ +#define DFTMODE_CNTRL 0x0054 /* DFT Mode Control */ + +/* DSI PPI Layer Registers */ +#define PPI_STARTPPI 0x0104 /* START control bit of PPI-TX function. */ +#define PPI_BUSYPPI 0x0108 +#define PPI_LINEINITCNT 0x0110 /* Line Initialization Wait Counter */ +#define PPI_LPTXTIMECNT 0x0114 +#define PPI_LANEENABLE 0x0134 /* Enables each lane at the PPI layer. */ +#define PPI_TX_RX_TA 0x013C /* DSI Bus Turn Around timing parameters */ + +/* Analog timer function enable */ +#define PPI_CLS_ATMR 0x0140 /* Delay for Clock Lane in LPRX */ +#define PPI_D0S_ATMR 0x0144 /* Delay for Data Lane 0 in LPRX */ +#define PPI_D1S_ATMR 0x0148 /* Delay for Data Lane 1 in LPRX */ +#define PPI_D2S_ATMR 0x014C /* Delay for Data Lane 2 in LPRX */ +#define PPI_D3S_ATMR 0x0150 /* Delay for Data Lane 3 in LPRX */ + +#define PPI_D0S_CLRSIPOCOUNT 0x0164 /* For lane 0 */ +#define PPI_D1S_CLRSIPOCOUNT 0x0168 /* For lane 1 */ +#define PPI_D2S_CLRSIPOCOUNT 0x016C /* For lane 2 */ +#define PPI_D3S_CLRSIPOCOUNT 0x0170 /* For lane 3 */ + +#define CLS_PRE 0x0180 /* Digital Counter inside of PHY IO */ +#define D0S_PRE 0x0184 /* Digital Counter inside of PHY IO */ +#define D1S_PRE 0x0188 /* Digital Counter inside of PHY IO */ +#define D2S_PRE 0x018C /* Digital Counter inside of PHY IO */ +#define D3S_PRE 0x0190 /* Digital Counter inside of PHY IO */ +#define CLS_PREP 0x01A0 /* Digital Counter inside of PHY IO */ +#define D0S_PREP 0x01A4 /* Digital Counter inside of PHY IO */ +#define D1S_PREP 0x01A8 /* Digital Counter inside of PHY IO */ +#define D2S_PREP 0x01AC /* Digital Counter inside of PHY IO */ +#define D3S_PREP 0x01B0 /* Digital Counter inside of PHY IO */ +#define CLS_ZERO 0x01C0 /* Digital Counter inside of PHY IO */ +#define D0S_ZERO 0x01C4 /* Digital Counter inside of PHY IO */ +#define D1S_ZERO 0x01C8 /* Digital Counter inside of PHY IO */ +#define D2S_ZERO 0x01CC /* Digital Counter inside of PHY IO */ +#define D3S_ZERO 0x01D0 /* Digital Counter inside of PHY IO */ + +#define PPI_CLRFLG 0x01E0 /* PRE Counters has reached set values */ +#define PPI_CLRSIPO 0x01E4 /* Clear SIPO values, Slave mode use only. */ +#define HSTIMEOUT 0x01F0 /* HS Rx Time Out Counter */ +#define HSTIMEOUTENABLE 0x01F4 /* Enable HS Rx Time Out Counter */ +#define DSI_STARTDSI 0x0204 /* START control bit of DSI-TX function */ +#define DSI_BUSYDSI 0x0208 +#define DSI_LANEENABLE 0x0210 /* Enables each lane at the Protocol layer. */ +#define DSI_LANESTATUS0 0x0214 /* Displays lane is in HS RX mode. */ +#define DSI_LANESTATUS1 0x0218 /* Displays lane is in ULPS or STOP state */ + +#define DSI_INTSTATUS 0x0220 /* Interrupt Status */ +#define DSI_INTMASK 0x0224 /* Interrupt Mask */ +#define DSI_INTCLR 0x0228 /* Interrupt Clear */ +#define DSI_LPTXTO 0x0230 /* Low Power Tx Time Out Counter */ + +#define DSIERRCNT 0x0300 /* DSI Error Count */ +#define APLCTRL 0x0400 /* Application Layer Control */ +#define RDPKTLN 0x0404 /* Command Read Packet Length */ + +#define VPCTRL 0x0450 /* Video Path Control */ +#define HTIM1 0x0454 /* Horizontal Timing Control 1 */ +#define HTIM2 0x0458 /* Horizontal Timing Control 2 */ +#define VTIM1 0x045C /* Vertical Timing Control 1 */ +#define VTIM2 0x0460 /* Vertical Timing Control 2 */ +#define VFUEN 0x0464 /* Video Frame Timing Update Enable */ + +/* Mux Input Select for LVDS LINK Input */ +#define LV_MX0003 0x0480 /* Bit 0 to 3 */ +#define LV_MX0407 0x0484 /* Bit 4 to 7 */ +#define LV_MX0811 0x0488 /* Bit 8 to 11 */ +#define LV_MX1215 0x048C /* Bit 12 to 15 */ +#define LV_MX1619 0x0490 /* Bit 16 to 19 */ +#define LV_MX2023 0x0494 /* Bit 20 to 23 */ +#define LV_MX2427 0x0498 /* Bit 24 to 27 */ +#define LV_MX(b0, b1, b2, b3) (FLD_VAL(b0, 4, 0) | FLD_VAL(b1, 12, 8) | \ + FLD_VAL(b2, 20, 16) | FLD_VAL(b3, 28, 24)) + +/* Input bit numbers used in mux registers */ +enum { + LVI_R0, + LVI_R1, + LVI_R2, + LVI_R3, + LVI_R4, + LVI_R5, + LVI_R6, + LVI_R7, + LVI_G0, + LVI_G1, + LVI_G2, + LVI_G3, + LVI_G4, + LVI_G5, + LVI_G6, + LVI_G7, + LVI_B0, + LVI_B1, + LVI_B2, + LVI_B3, + LVI_B4, + LVI_B5, + LVI_B6, + LVI_B7, + LVI_HS, + LVI_VS, + LVI_DE, + LVI_L0 +}; + +#define LVCFG 0x049C /* LVDS Configuration */ +#define LVPHY0 0x04A0 /* LVDS PHY 0 */ +#define LVPHY1 0x04A4 /* LVDS PHY 1 */ +#define SYSSTAT 0x0500 /* System Status */ +#define SYSRST 0x0504 /* System Reset */ +/* GPIO Registers */ +#define GPIOC 0x0520 /* GPIO Control */ +#define GPIOO 0x0524 /* GPIO Output */ +#define GPIOI 0x0528 /* GPIO Input */ + +/* I2C Registers */ +#define I2CTIMCTRL 0x0540 /* I2C IF Timing and Enable Control */ +#define I2CMADDR 0x0544 /* I2C Master Addressing */ +#define WDATAQ 0x0548 /* Write Data Queue */ +#define RDATAQ 0x054C /* Read Data Queue */ + +/* Chip ID and Revision ID Register */ +#define IDREG 0x0580 + +#define LPX_PERIOD 4 +#define TTA_GET 0x40000 +#define TTA_SURE 6 + +#define TC358775XBG_ID 0x00007500 + +/* Debug Registers */ +#define DEBUG00 0x05A0 /* Debug */ +#define DEBUG01 0x05A4 /* LVDS Data */ + +#define DSI_CLEN_BIT BIT(0) +#define DIVIDE_BY_3 3 /* PCLK=DCLK/3 */ +#define LVCFG_LVEN_BIT BIT(0) + +#define L0EN BIT(1) + + +#define TC358775_VPCTRL_VSDELAY__MASK 0x3FF00000 +#define TC358775_VPCTRL_VSDELAY__SHIFT 20 +static inline u32 TC358775_VPCTRL_VSDELAY(uint32_t val) +{ + return ((val) << TC358775_VPCTRL_VSDELAY__SHIFT) & + TC358775_VPCTRL_VSDELAY__MASK; +} + +#define TC358775_VPCTRL_OPXLFMT__MASK 0x00000100 +#define TC358775_VPCTRL_OPXLFMT__SHIFT 8 +static inline u32 TC358775_VPCTRL_OPXLFMT(uint32_t val) +{ + return ((val) << TC358775_VPCTRL_OPXLFMT__SHIFT) & + TC358775_VPCTRL_OPXLFMT__MASK; +} + +#define TC358775_VPCTRL_MSF__MASK 0x00000001 +#define TC358775_VPCTRL_MSF__SHIFT 0 +static inline u32 TC358775_VPCTRL_MSF(uint32_t val) +{ + return ((val) << TC358775_VPCTRL_MSF__SHIFT) & + TC358775_VPCTRL_MSF__MASK; +} + +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0 +#define TC358775_LVCFG_PCLKDIV__SHIFT 4 +static inline u32 TC358775_LVCFG_PCLKDIV(uint32_t val) +{ + return ((val) << TC358775_LVCFG_PCLKDIV__SHIFT) & + TC358775_LVCFG_PCLKDIV__MASK; +} + +#define TC358775_LVCFG_LVDLINK__MASK 0x00000002 +#define TC358775_LVCFG_LVDLINK__SHIFT 0 +static inline u32 TC358775_LVCFG_LVDLINK(uint32_t val) +{ + return ((val) << TC358775_LVCFG_LVDLINK__SHIFT) & + TC358775_LVCFG_LVDLINK__MASK; +} + +static const char * const regulator_names[] = { + "vdd", + "vddio" +}; + +struct tc_data { + struct i2c_client *i2c; + + struct device *dev; + struct regmap *regmap; + + struct drm_bridge bridge; + struct drm_connector connector; + struct drm_panel *panel; + + enum drm_connector_status status; + struct device_node *host_node; + struct mipi_dsi_device *dsi; + u8 num_dsi_lanes; + + struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)]; + struct gpio_desc *reset_gpio; + struct gpio_desc *stby_gpio; + u32 rev; + u8 dual_link; /* single-link or dual-link */ +}; + +static inline struct tc_data *bridge_to_tc(struct drm_bridge *b) +{ + return container_of(b, struct tc_data, bridge); +} + +static inline struct tc_data *connector_to_tc(struct drm_connector *c) +{ + return container_of(c, struct tc_data, connector); +} + +static void tc_bridge_pre_enable(struct drm_bridge *bridge) +{ + struct tc_data *tc = bridge_to_tc(bridge); + struct device *dev = &tc->dsi->dev; + int ret; + + ret = regulator_bulk_enable(ARRAY_SIZE(tc->supplies), tc->supplies); + if (ret < 0) { + dev_err(dev, "regulator enable failed, %d\n", ret); + return; + } + usleep_range(10000, 20000); + + gpiod_set_value(tc->stby_gpio, 0); + usleep_range(10, 20); + + gpiod_set_value(tc->reset_gpio, 0); + usleep_range(10000, 20000); + + drm_panel_prepare(tc->panel); +} + +static void tc_bridge_disable(struct drm_bridge *bridge) +{ + struct tc_data *tc = bridge_to_tc(bridge); + struct device *dev = &tc->dsi->dev; + int ret; + + ret = regulator_bulk_disable(ARRAY_SIZE(tc->supplies), tc->supplies); + if (ret < 0) + dev_err(dev, "regulator disable failed, %d\n", ret); + usleep_range(30000, 40000); + + drm_panel_disable(tc->panel); +} + +static void tc_bridge_post_disable(struct drm_bridge *bridge) +{ + struct tc_data *tc = bridge_to_tc(bridge); + + gpiod_set_value(tc->stby_gpio, 1); + usleep_range(10, 20); + + gpiod_set_value(tc->reset_gpio, 1); + usleep_range(10000, 20000); + + drm_panel_unprepare(tc->panel); +} + +static int d2l_write(struct tc_data *tc, u16 reg, u32 data) +{ + int ret = 0; + + ret = regmap_bulk_write(tc->regmap, reg, (u32[]) {data}, 1); + + return ret; +} + +static void tc_bridge_enable(struct drm_bridge *bridge) +{ + struct tc_data *tc = bridge_to_tc(bridge); + int ret; + u32 hbpr, hpw, htime1, hfpr, hsize, htime2; + u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2; + u32 val = 0; + u16 bus_formats; + struct drm_display_mode *mode; + + mode = &bridge->encoder->crtc->state->adjusted_mode; + + hbpr = 0; + hpw = mode->hsync_end - mode->hsync_start; + vbpr = 0; + vpw = mode->vsync_end - mode->vsync_start; + + htime1 = (hbpr << 16) + hpw; + vtime1 = (vbpr << 16) + vpw; + + hfpr = mode->hsync_start - mode->hdisplay; + hsize = mode->hdisplay; + vfpr = mode->vsync_start - mode->vdisplay; + vsize = mode->vdisplay; + + htime2 = (hfpr << 16) + hsize; + vtime2 = (vfpr << 16) + vsize; + + ret = regmap_read(tc->regmap, IDREG, &tc->rev); + if (ret) { + dev_err(tc->dev, "can not read device ID: %d\n", ret); + return; + } + dev_info(tc->dev, "DSI2LVDS Chip ID.%02x Revision ID. %02x\n", + (tc->rev>>8)&0xFF, (tc->rev)&0xFF); + + d2l_write(tc, SYSRST, 0x000000FF); + usleep_range(30000, 40000); + + d2l_write(tc, PPI_TX_RX_TA, TTA_GET | TTA_SURE); + d2l_write(tc, PPI_LPTXTIMECNT, LPX_PERIOD); + d2l_write(tc, PPI_D0S_CLRSIPOCOUNT, 3); + d2l_write(tc, PPI_D1S_CLRSIPOCOUNT, 3); + d2l_write(tc, PPI_D2S_CLRSIPOCOUNT, 3); + d2l_write(tc, PPI_D3S_CLRSIPOCOUNT, 3); + + val = ((L0EN << tc->num_dsi_lanes) - L0EN) | DSI_CLEN_BIT; + d2l_write(tc, PPI_LANEENABLE, val); + d2l_write(tc, DSI_LANEENABLE, val); + + d2l_write(tc, PPI_STARTPPI, 0x00000001); + d2l_write(tc, DSI_STARTDSI, 0x00000001); + + val = TC358775_VPCTRL_VSDELAY(21); //TODO : to set the dynamic value + + bus_formats = tc->connector.display_info.bus_formats[0]; + + if (bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_SPWG + || bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA) { + /* RGB888 */ + val |= TC358775_VPCTRL_OPXLFMT(1); + d2l_write(tc, VPCTRL, val); + } else { + /* RGB666 */ + val |= TC358775_VPCTRL_MSF(1); + d2l_write(tc, VPCTRL, val); + } + + d2l_write(tc, HTIM1, htime1); + d2l_write(tc, VTIM1, vtime1); + d2l_write(tc, HTIM2, htime2); + d2l_write(tc, VTIM2, vtime2); + + d2l_write(tc, VFUEN, 0x00000001); + d2l_write(tc, SYSRST, 0x00000004); + d2l_write(tc, LVPHY0, 0x00040006); + + /* default jeida-24 */ + if (bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_SPWG) { + /* vesa-24, TODO jeida-18*/ + d2l_write(tc, LV_MX0003, LV_MX(LVI_R0, LVI_R1, LVI_R2, LVI_R3)); + d2l_write(tc, LV_MX0407, LV_MX(LVI_R4, LVI_R7, LVI_R5, LVI_G0)); + d2l_write(tc, LV_MX0811, LV_MX(LVI_G1, LVI_G2, LVI_G6, LVI_G7)); + d2l_write(tc, LV_MX1215, LV_MX(LVI_G3, LVI_G4, LVI_G5, LVI_B0)); + d2l_write(tc, LV_MX1619, LV_MX(LVI_B6, LVI_B7, LVI_B1, LVI_B2)); + d2l_write(tc, LV_MX2023, LV_MX(LVI_B3, LVI_B4, LVI_B5, LVI_L0)); + d2l_write(tc, LV_MX2427, LV_MX(LVI_HS, LVI_VS, LVI_DE, LVI_R6)); + } + + d2l_write(tc, VFUEN, 0x00000001); + + val = TC358775_LVCFG_PCLKDIV(DIVIDE_BY_3) | LVCFG_LVEN_BIT; + if (tc->dual_link) + val |= TC358775_LVCFG_LVDLINK(1); + + d2l_write(tc, LVCFG, val); + + drm_panel_enable(tc->panel); +} + +static int tc_connector_get_modes(struct drm_connector *connector) +{ + struct tc_data *tc = connector_to_tc(connector); + struct edid *edid; + unsigned int count; + + if (tc->panel && tc->panel->funcs && tc->panel->funcs->get_modes) { + count = tc->panel->funcs->get_modes(tc->panel, connector); + if (count > 0) + return count; + } + + edid = drm_get_edid(connector, tc->i2c->adapter); + if (!edid) + return 0; + + drm_connector_update_edid_property(connector, edid); + count = drm_add_edid_modes(connector, edid); + kfree(edid); + + return count; +} + +static int tc_connector_mode_valid(struct drm_connector *connector, + struct drm_display_mode *mode) +{ + struct tc_data *tc = connector_to_tc(connector); + + /* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */ + if ((mode->clock > 135000 && tc->dual_link == 0) || + (mode->clock > 270000 && tc->dual_link == 1)) + return MODE_CLOCK_HIGH; + + return MODE_OK; +} + +static struct drm_encoder * +tc_connector_best_encoder(struct drm_connector *connector) +{ + struct tc_data *tc = connector_to_tc(connector); + + return tc->bridge.encoder; +} + +static const struct drm_connector_helper_funcs tc_connector_helper_funcs = { + .get_modes = tc_connector_get_modes, + .mode_valid = tc_connector_mode_valid, + .best_encoder = tc_connector_best_encoder, +}; + +static const struct drm_connector_funcs tc_connector_funcs = { + .fill_modes = drm_helper_probe_single_connector_modes, + .destroy = drm_connector_cleanup, + .reset = drm_atomic_helper_connector_reset, + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, +}; + +int tc358775_parse_dt(struct device_node *np, struct tc_data *tc) +{ + u32 num_lanes; + u8 dual_link; + + of_property_read_u8(np, "tc,dual-link", &dual_link); + of_property_read_u32(np, "tc,dsi-lanes", &num_lanes); + + if (num_lanes < 1 || num_lanes > 4) + return -EINVAL; + + tc->num_dsi_lanes = num_lanes; + tc->dual_link = dual_link; + + tc->host_node = of_graph_get_remote_node(np, 0, 0); + if (!tc->host_node) + return -ENODEV; + + of_node_put(tc->host_node); + + return 0; +} + +int tc358775_attach_dsi(struct tc_data *tc) +{ + struct device *dev = &tc->i2c->dev; + struct mipi_dsi_host *host; + struct mipi_dsi_device *dsi; + int ret = 0; + const struct mipi_dsi_device_info info = { .type = "tc358775", + .channel = 0, + .node = NULL, + }; + + host = of_find_mipi_dsi_host_by_node(tc->host_node); + if (!host) { + dev_err(dev, "failed to find dsi host\n"); + return -EPROBE_DEFER; + } + + dsi = mipi_dsi_device_register_full(host, &info); + if (IS_ERR(dsi)) { + dev_err(dev, "failed to create dsi device\n"); + ret = PTR_ERR(dsi); + goto err_dsi_device; + } + + tc->dsi = dsi; + + dsi->lanes = tc->num_dsi_lanes; + dsi->format = MIPI_DSI_FMT_RGB888; + dsi->mode_flags = MIPI_DSI_MODE_VIDEO; + + ret = mipi_dsi_attach(dsi); + if (ret < 0) { + dev_err(dev, "failed to attach dsi to host\n"); + goto err_dsi_attach; + } + + return 0; + +err_dsi_attach: + mipi_dsi_device_unregister(dsi); +err_dsi_device: + return ret; +} + +static int tc_bridge_attach(struct drm_bridge *bridge) +{ + struct tc_data *tc = bridge_to_tc(bridge); + struct drm_device *drm = bridge->dev; + int ret; + + /* Create LVDS connector */ + drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs); + ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs, + DRM_MODE_CONNECTOR_LVDS); + if (ret) + return ret; + + if (tc->panel) + drm_panel_attach(tc->panel, &tc->connector); + + drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder); + + ret = tc358775_attach_dsi(tc); + + return ret; +} + +static const struct drm_bridge_funcs tc_bridge_funcs = { + .attach = tc_bridge_attach, + .pre_enable = tc_bridge_pre_enable, + .enable = tc_bridge_enable, + .disable = tc_bridge_disable, + .post_disable = tc_bridge_post_disable, +}; + +static const struct regmap_config tc_regmap_config = { + .name = "tc358775", + .reg_bits = 16, + .val_bits = 32, + .reg_stride = 4, + .max_register = 0x05A8, + .cache_type = REGCACHE_RBTREE, + .reg_format_endian = REGMAP_ENDIAN_BIG, + .val_format_endian = REGMAP_ENDIAN_LITTLE, +}; + +static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id) +{ + struct device *dev = &client->dev; + struct tc_data *tc; + int ret; + unsigned int i; + + tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL); + if (!tc) + return -ENOMEM; + + tc->dev = dev; + tc->i2c = client; + tc->status = connector_status_connected; + + /* port@1 is the output port */ + ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &tc->panel, NULL); + if (ret && ret != -ENODEV) + return ret; + + ret = tc358775_parse_dt(dev->of_node, tc); + if (ret) + return ret; + + for (i = 0; i < ARRAY_SIZE(tc->supplies); i++) + tc->supplies[i].supply = regulator_names[i]; + + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(tc->supplies), + tc->supplies); + if (ret < 0) + dev_err(dev, "failed to init regulator, ret=%d\n", ret); + + tc->stby_gpio = devm_gpiod_get(dev, "stby", GPIOD_OUT_HIGH); + if (IS_ERR(tc->stby_gpio)) { + ret = PTR_ERR(tc->stby_gpio); + dev_err(dev, "cannot get stby-gpio %d\n", ret); + return ret; + } + + tc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(tc->reset_gpio)) { + ret = PTR_ERR(tc->reset_gpio); + dev_err(dev, "cannot get reset-gpios %d\n", ret); + return ret; + } + + tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config); + if (IS_ERR(tc->regmap)) { + ret = PTR_ERR(tc->regmap); + dev_err(dev, "Failed to initialize regmap: %d\n", ret); + return ret; + } + + tc->bridge.funcs = &tc_bridge_funcs; + tc->bridge.of_node = dev->of_node; + drm_bridge_add(&tc->bridge); + + i2c_set_clientdata(client, tc); + + return 0; +} + +static int tc_remove(struct i2c_client *client) +{ + struct tc_data *tc = i2c_get_clientdata(client); + + drm_bridge_remove(&tc->bridge); + + return 0; +} + +static const struct i2c_device_id tc358775_i2c_ids[] = { + { "tc358775", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, tc358775_i2c_ids); + +static const struct of_device_id tc358775_of_ids[] = { + { .compatible = "toshiba,tc358775", }, + { } +}; +MODULE_DEVICE_TABLE(of, tc358775_of_ids); + +static struct i2c_driver tc358775_driver = { + .driver = { + .name = "tc358775", + .of_match_table = tc358775_of_ids, + }, + .id_table = tc358775_i2c_ids, + .probe = tc_probe, + .remove = tc_remove, +}; +module_i2c_driver(tc358775_driver); + +MODULE_AUTHOR("Vinay Simha BN <vinaysimha@inforcecomputing.com>"); +MODULE_DESCRIPTION("tc358775 LVDS encoder driver"); +MODULE_LICENSE("GPL v2"); -- 2.7.4 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH 2/2] display/drm/bridge: tc358775 DSI/LVDS driver 2020-03-11 9:48 ` [PATCH 2/2] display/drm/bridge: tc358775 DSI/LVDS driver Vinay Simha BN @ 2020-03-12 10:50 ` Andrzej Hajda 0 siblings, 0 replies; 10+ messages in thread From: Andrzej Hajda @ 2020-03-12 10:50 UTC (permalink / raw) To: Vinay Simha BN, Laurent Pinchart Cc: Jernej Skrabec, Jonas Karlman, David Airlie, Neil Armstrong, open list, open list:DRM DRIVERS On 11.03.2020 10:48, Vinay Simha BN wrote: > dsi2lvds tc358775 bridge driver added > Tested in apq8016, ifc6309 board and panel > auo,b101xtn01 > > Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> > --- > v1: > Initial version > > v2: > * Andrzej Hajda review comments incorporated > SPDX identifier > development debug removed > alphabetic order headers > u32 instead of unit32_t > magic numbers to macros for CLRSI and mux registers > ignored return value > > * Laurent Pinchart review comments incorporated > mdelay to usleep_range > bus_formats added > --- > drivers/gpu/drm/bridge/Kconfig | 10 + > drivers/gpu/drm/bridge/Makefile | 1 + > drivers/gpu/drm/bridge/tc358775.c | 688 ++++++++++++++++++++++++++++++++++++++ > 3 files changed, 699 insertions(+) > create mode 100644 drivers/gpu/drm/bridge/tc358775.c > > diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig > index 8397bf7..d5528fa 100644 > --- a/drivers/gpu/drm/bridge/Kconfig > +++ b/drivers/gpu/drm/bridge/Kconfig > @@ -133,6 +133,16 @@ config DRM_TOSHIBA_TC358767 > ---help--- > Toshiba TC358767 eDP bridge chip driver. > > +config DRM_TOSHIBA_TC358775 > + tristate "Toshiba TC358775 LVDS bridge" > + depends on OF > + select DRM_KMS_HELPER > + select REGMAP_I2C > + select DRM_PANEL > + select DRM_MIPI_DSI > + ---help--- > + Toshiba TC358775 LVDS bridge chip driver. > + > config DRM_TI_TFP410 > tristate "TI TFP410 DVI/HDMI bridge" > depends on OF > diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile > index 1eb5376..9b2c512 100644 > --- a/drivers/gpu/drm/bridge/Makefile > +++ b/drivers/gpu/drm/bridge/Makefile > @@ -12,6 +12,7 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o > obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o > obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o > obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o > +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o > obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/ > obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o > obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o > diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c > new file mode 100644 > index 0000000..28b828e > --- /dev/null > +++ b/drivers/gpu/drm/bridge/tc358775.c > @@ -0,0 +1,688 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * tc358775 DSI to LVDS bridge driver > + * > + * Copyright (C) 2020 InforceComputing > + * Author: Vinay Simha BN <vinaysimha@inforcecomputing.com> > + * > + */ > +#define DEBUG > +#include <linux/clk.h> > +#include <linux/device.h> > +#include <linux/gpio/consumer.h> > +#include <linux/i2c.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/regmap.h> > +#include <linux/regulator/consumer.h> > +#include <linux/slab.h> > + > +#include <drm/drm_atomic_helper.h> > +#include <drm/drm_bridge.h> > +#include <drm/drm_crtc_helper.h> > +#include <drm/drm_dp_helper.h> > +#include <drm/drm_mipi_dsi.h> > +#include <drm/drm_of.h> > +#include <drm/drm_panel.h> > +#include <drm/drm_probe_helper.h> > + > +#define FLD_MASK(start, end) (((1 << ((start) - (end) + 1)) - 1) << (end)) > +#define FLD_VAL(val, start, end) (((val) << (end)) & FLD_MASK(start, end)) > + > +/* Registers */ > + > +/* DSI D-PHY Layer Registers */ > +#define D0W_DPHYCONTTX 0x0004 /* Data Lane 0 DPHY Tx Control */ > +#define CLW_DPHYCONTRX 0x0020 /* Clock Lane DPHY Rx Control */ > +#define D0W_DPHYCONTRX 0x0024 /* Data Lane 0 DPHY Rx Control */ > +#define D1W_DPHYCONTRX 0x0028 /* Data Lane 1 DPHY Rx Control */ > +#define D2W_DPHYCONTRX 0x002C /* Data Lane 2 DPHY Rx Control */ > +#define D3W_DPHYCONTRX 0x0030 /* Data Lane 3 DPHY Rx Control */ > +#define COM_DPHYCONTRX 0x0038 /* DPHY Rx Common Control */ > +#define CLW_CNTRL 0x0040 /* Clock Lane Control */ > +#define D0W_CNTRL 0x0044 /* Data Lane 0 Control */ > +#define D1W_CNTRL 0x0048 /* Data Lane 1 Control */ > +#define D2W_CNTRL 0x004C /* Data Lane 2 Control */ > +#define D3W_CNTRL 0x0050 /* Data Lane 3 Control */ > +#define DFTMODE_CNTRL 0x0054 /* DFT Mode Control */ > + > +/* DSI PPI Layer Registers */ > +#define PPI_STARTPPI 0x0104 /* START control bit of PPI-TX function. */ > +#define PPI_BUSYPPI 0x0108 > +#define PPI_LINEINITCNT 0x0110 /* Line Initialization Wait Counter */ > +#define PPI_LPTXTIMECNT 0x0114 > +#define PPI_LANEENABLE 0x0134 /* Enables each lane at the PPI layer. */ > +#define PPI_TX_RX_TA 0x013C /* DSI Bus Turn Around timing parameters */ > + > +/* Analog timer function enable */ > +#define PPI_CLS_ATMR 0x0140 /* Delay for Clock Lane in LPRX */ > +#define PPI_D0S_ATMR 0x0144 /* Delay for Data Lane 0 in LPRX */ > +#define PPI_D1S_ATMR 0x0148 /* Delay for Data Lane 1 in LPRX */ > +#define PPI_D2S_ATMR 0x014C /* Delay for Data Lane 2 in LPRX */ > +#define PPI_D3S_ATMR 0x0150 /* Delay for Data Lane 3 in LPRX */ > + > +#define PPI_D0S_CLRSIPOCOUNT 0x0164 /* For lane 0 */ > +#define PPI_D1S_CLRSIPOCOUNT 0x0168 /* For lane 1 */ > +#define PPI_D2S_CLRSIPOCOUNT 0x016C /* For lane 2 */ > +#define PPI_D3S_CLRSIPOCOUNT 0x0170 /* For lane 3 */ > + > +#define CLS_PRE 0x0180 /* Digital Counter inside of PHY IO */ > +#define D0S_PRE 0x0184 /* Digital Counter inside of PHY IO */ > +#define D1S_PRE 0x0188 /* Digital Counter inside of PHY IO */ > +#define D2S_PRE 0x018C /* Digital Counter inside of PHY IO */ > +#define D3S_PRE 0x0190 /* Digital Counter inside of PHY IO */ > +#define CLS_PREP 0x01A0 /* Digital Counter inside of PHY IO */ > +#define D0S_PREP 0x01A4 /* Digital Counter inside of PHY IO */ > +#define D1S_PREP 0x01A8 /* Digital Counter inside of PHY IO */ > +#define D2S_PREP 0x01AC /* Digital Counter inside of PHY IO */ > +#define D3S_PREP 0x01B0 /* Digital Counter inside of PHY IO */ > +#define CLS_ZERO 0x01C0 /* Digital Counter inside of PHY IO */ > +#define D0S_ZERO 0x01C4 /* Digital Counter inside of PHY IO */ > +#define D1S_ZERO 0x01C8 /* Digital Counter inside of PHY IO */ > +#define D2S_ZERO 0x01CC /* Digital Counter inside of PHY IO */ > +#define D3S_ZERO 0x01D0 /* Digital Counter inside of PHY IO */ > + > +#define PPI_CLRFLG 0x01E0 /* PRE Counters has reached set values */ > +#define PPI_CLRSIPO 0x01E4 /* Clear SIPO values, Slave mode use only. */ > +#define HSTIMEOUT 0x01F0 /* HS Rx Time Out Counter */ > +#define HSTIMEOUTENABLE 0x01F4 /* Enable HS Rx Time Out Counter */ > +#define DSI_STARTDSI 0x0204 /* START control bit of DSI-TX function */ > +#define DSI_BUSYDSI 0x0208 > +#define DSI_LANEENABLE 0x0210 /* Enables each lane at the Protocol layer. */ > +#define DSI_LANESTATUS0 0x0214 /* Displays lane is in HS RX mode. */ > +#define DSI_LANESTATUS1 0x0218 /* Displays lane is in ULPS or STOP state */ > + > +#define DSI_INTSTATUS 0x0220 /* Interrupt Status */ > +#define DSI_INTMASK 0x0224 /* Interrupt Mask */ > +#define DSI_INTCLR 0x0228 /* Interrupt Clear */ > +#define DSI_LPTXTO 0x0230 /* Low Power Tx Time Out Counter */ > + > +#define DSIERRCNT 0x0300 /* DSI Error Count */ > +#define APLCTRL 0x0400 /* Application Layer Control */ > +#define RDPKTLN 0x0404 /* Command Read Packet Length */ > + > +#define VPCTRL 0x0450 /* Video Path Control */ > +#define HTIM1 0x0454 /* Horizontal Timing Control 1 */ > +#define HTIM2 0x0458 /* Horizontal Timing Control 2 */ > +#define VTIM1 0x045C /* Vertical Timing Control 1 */ > +#define VTIM2 0x0460 /* Vertical Timing Control 2 */ > +#define VFUEN 0x0464 /* Video Frame Timing Update Enable */ > + > +/* Mux Input Select for LVDS LINK Input */ > +#define LV_MX0003 0x0480 /* Bit 0 to 3 */ > +#define LV_MX0407 0x0484 /* Bit 4 to 7 */ > +#define LV_MX0811 0x0488 /* Bit 8 to 11 */ > +#define LV_MX1215 0x048C /* Bit 12 to 15 */ > +#define LV_MX1619 0x0490 /* Bit 16 to 19 */ > +#define LV_MX2023 0x0494 /* Bit 20 to 23 */ > +#define LV_MX2427 0x0498 /* Bit 24 to 27 */ > +#define LV_MX(b0, b1, b2, b3) (FLD_VAL(b0, 4, 0) | FLD_VAL(b1, 12, 8) | \ > + FLD_VAL(b2, 20, 16) | FLD_VAL(b3, 28, 24)) > + > +/* Input bit numbers used in mux registers */ > +enum { > + LVI_R0, > + LVI_R1, > + LVI_R2, > + LVI_R3, > + LVI_R4, > + LVI_R5, > + LVI_R6, > + LVI_R7, > + LVI_G0, > + LVI_G1, > + LVI_G2, > + LVI_G3, > + LVI_G4, > + LVI_G5, > + LVI_G6, > + LVI_G7, > + LVI_B0, > + LVI_B1, > + LVI_B2, > + LVI_B3, > + LVI_B4, > + LVI_B5, > + LVI_B6, > + LVI_B7, > + LVI_HS, > + LVI_VS, > + LVI_DE, > + LVI_L0 > +}; > + > +#define LVCFG 0x049C /* LVDS Configuration */ > +#define LVPHY0 0x04A0 /* LVDS PHY 0 */ > +#define LVPHY1 0x04A4 /* LVDS PHY 1 */ > +#define SYSSTAT 0x0500 /* System Status */ > +#define SYSRST 0x0504 /* System Reset */ > +/* GPIO Registers */ > +#define GPIOC 0x0520 /* GPIO Control */ > +#define GPIOO 0x0524 /* GPIO Output */ > +#define GPIOI 0x0528 /* GPIO Input */ > + > +/* I2C Registers */ > +#define I2CTIMCTRL 0x0540 /* I2C IF Timing and Enable Control */ > +#define I2CMADDR 0x0544 /* I2C Master Addressing */ > +#define WDATAQ 0x0548 /* Write Data Queue */ > +#define RDATAQ 0x054C /* Read Data Queue */ > + > +/* Chip ID and Revision ID Register */ > +#define IDREG 0x0580 > + > +#define LPX_PERIOD 4 > +#define TTA_GET 0x40000 > +#define TTA_SURE 6 > + > +#define TC358775XBG_ID 0x00007500 > + > +/* Debug Registers */ > +#define DEBUG00 0x05A0 /* Debug */ > +#define DEBUG01 0x05A4 /* LVDS Data */ > + > +#define DSI_CLEN_BIT BIT(0) > +#define DIVIDE_BY_3 3 /* PCLK=DCLK/3 */ > +#define LVCFG_LVEN_BIT BIT(0) > + > +#define L0EN BIT(1) > + > + > +#define TC358775_VPCTRL_VSDELAY__MASK 0x3FF00000 > +#define TC358775_VPCTRL_VSDELAY__SHIFT 20 > +static inline u32 TC358775_VPCTRL_VSDELAY(uint32_t val) > +{ > + return ((val) << TC358775_VPCTRL_VSDELAY__SHIFT) & > + TC358775_VPCTRL_VSDELAY__MASK; > +} > + > +#define TC358775_VPCTRL_OPXLFMT__MASK 0x00000100 > +#define TC358775_VPCTRL_OPXLFMT__SHIFT 8 > +static inline u32 TC358775_VPCTRL_OPXLFMT(uint32_t val) > +{ > + return ((val) << TC358775_VPCTRL_OPXLFMT__SHIFT) & > + TC358775_VPCTRL_OPXLFMT__MASK; > +} > + > +#define TC358775_VPCTRL_MSF__MASK 0x00000001 > +#define TC358775_VPCTRL_MSF__SHIFT 0 > +static inline u32 TC358775_VPCTRL_MSF(uint32_t val) > +{ > + return ((val) << TC358775_VPCTRL_MSF__SHIFT) & > + TC358775_VPCTRL_MSF__MASK; > +} > + > +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0 > +#define TC358775_LVCFG_PCLKDIV__SHIFT 4 > +static inline u32 TC358775_LVCFG_PCLKDIV(uint32_t val) > +{ > + return ((val) << TC358775_LVCFG_PCLKDIV__SHIFT) & > + TC358775_LVCFG_PCLKDIV__MASK; > +} > + > +#define TC358775_LVCFG_LVDLINK__MASK 0x00000002 > +#define TC358775_LVCFG_LVDLINK__SHIFT 0 > +static inline u32 TC358775_LVCFG_LVDLINK(uint32_t val) > +{ > + return ((val) << TC358775_LVCFG_LVDLINK__SHIFT) & > + TC358775_LVCFG_LVDLINK__MASK; > +} > + > +static const char * const regulator_names[] = { > + "vdd", > + "vddio" > +}; > + > +struct tc_data { > + struct i2c_client *i2c; > + > + struct device *dev; > + struct regmap *regmap; > + > + struct drm_bridge bridge; > + struct drm_connector connector; > + struct drm_panel *panel; > + > + enum drm_connector_status status; As I commented this field is unused, writing to it once, does not make it 'used'. > + struct device_node *host_node; > + struct mipi_dsi_device *dsi; > + u8 num_dsi_lanes; > + > + struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)]; > + struct gpio_desc *reset_gpio; > + struct gpio_desc *stby_gpio; > + u32 rev; This field is also not needed, you can use local variable instead. > + u8 dual_link; /* single-link or dual-link */ > +}; > + > +static inline struct tc_data *bridge_to_tc(struct drm_bridge *b) > +{ > + return container_of(b, struct tc_data, bridge); > +} > + > +static inline struct tc_data *connector_to_tc(struct drm_connector *c) > +{ > + return container_of(c, struct tc_data, connector); > +} > + > +static void tc_bridge_pre_enable(struct drm_bridge *bridge) > +{ > + struct tc_data *tc = bridge_to_tc(bridge); > + struct device *dev = &tc->dsi->dev; > + int ret; > + > + ret = regulator_bulk_enable(ARRAY_SIZE(tc->supplies), tc->supplies); Specs says regulator enabling should be ordered with proper delays. > + if (ret < 0) { > + dev_err(dev, "regulator enable failed, %d\n", ret); > + return; > + } > + usleep_range(10000, 20000); > + > + gpiod_set_value(tc->stby_gpio, 0); > + usleep_range(10, 20); > + > + gpiod_set_value(tc->reset_gpio, 0); > + usleep_range(10000, 20000); > + > + drm_panel_prepare(tc->panel); > +} > + > +static void tc_bridge_disable(struct drm_bridge *bridge) > +{ > + struct tc_data *tc = bridge_to_tc(bridge); > + struct device *dev = &tc->dsi->dev; > + int ret; > + > + ret = regulator_bulk_disable(ARRAY_SIZE(tc->supplies), tc->supplies); Disabling regulators here does not make sense, and is against specs you pointed in earlier email, see chapter 8.4.5. In bridge disable you should only stop data transmission, power-off sequence should be moved to post-disable and reordered according to docs. > + if (ret < 0) > + dev_err(dev, "regulator disable failed, %d\n", ret); > + usleep_range(30000, 40000); > + > + drm_panel_disable(tc->panel); > +} > + > +static void tc_bridge_post_disable(struct drm_bridge *bridge) > +{ > + struct tc_data *tc = bridge_to_tc(bridge); > + > + gpiod_set_value(tc->stby_gpio, 1); > + usleep_range(10, 20); > + > + gpiod_set_value(tc->reset_gpio, 1); > + usleep_range(10000, 20000); > + > + drm_panel_unprepare(tc->panel); > +} > + > +static int d2l_write(struct tc_data *tc, u16 reg, u32 data) > +{ > + int ret = 0; > + > + ret = regmap_bulk_write(tc->regmap, reg, (u32[]) {data}, 1); > + > + return ret; > +} > + > +static void tc_bridge_enable(struct drm_bridge *bridge) > +{ > + struct tc_data *tc = bridge_to_tc(bridge); > + int ret; > + u32 hbpr, hpw, htime1, hfpr, hsize, htime2; > + u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2; > + u32 val = 0; > + u16 bus_formats; > + struct drm_display_mode *mode; > + > + mode = &bridge->encoder->crtc->state->adjusted_mode; > + > + hbpr = 0; > + hpw = mode->hsync_end - mode->hsync_start; > + vbpr = 0; > + vpw = mode->vsync_end - mode->vsync_start; > + > + htime1 = (hbpr << 16) + hpw; > + vtime1 = (vbpr << 16) + vpw; > + > + hfpr = mode->hsync_start - mode->hdisplay; > + hsize = mode->hdisplay; > + vfpr = mode->vsync_start - mode->vdisplay; > + vsize = mode->vdisplay; > + > + htime2 = (hfpr << 16) + hsize; > + vtime2 = (vfpr << 16) + vsize; > + > + ret = regmap_read(tc->regmap, IDREG, &tc->rev); > + if (ret) { > + dev_err(tc->dev, "can not read device ID: %d\n", ret); > + return; > + } > + dev_info(tc->dev, "DSI2LVDS Chip ID.%02x Revision ID. %02x\n", > + (tc->rev>>8)&0xFF, (tc->rev)&0xFF); > + > + d2l_write(tc, SYSRST, 0x000000FF); > + usleep_range(30000, 40000); > + > + d2l_write(tc, PPI_TX_RX_TA, TTA_GET | TTA_SURE); > + d2l_write(tc, PPI_LPTXTIMECNT, LPX_PERIOD); > + d2l_write(tc, PPI_D0S_CLRSIPOCOUNT, 3); > + d2l_write(tc, PPI_D1S_CLRSIPOCOUNT, 3); > + d2l_write(tc, PPI_D2S_CLRSIPOCOUNT, 3); > + d2l_write(tc, PPI_D3S_CLRSIPOCOUNT, 3); > + > + val = ((L0EN << tc->num_dsi_lanes) - L0EN) | DSI_CLEN_BIT; > + d2l_write(tc, PPI_LANEENABLE, val); > + d2l_write(tc, DSI_LANEENABLE, val); > + > + d2l_write(tc, PPI_STARTPPI, 0x00000001); > + d2l_write(tc, DSI_STARTDSI, 0x00000001); > + > + val = TC358775_VPCTRL_VSDELAY(21); //TODO : to set the dynamic value > + > + bus_formats = tc->connector.display_info.bus_formats[0]; > + > + if (bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_SPWG > + || bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA) { > + /* RGB888 */ > + val |= TC358775_VPCTRL_OPXLFMT(1); > + d2l_write(tc, VPCTRL, val); > + } else { > + /* RGB666 */ > + val |= TC358775_VPCTRL_MSF(1); > + d2l_write(tc, VPCTRL, val); > + } > + > + d2l_write(tc, HTIM1, htime1); > + d2l_write(tc, VTIM1, vtime1); > + d2l_write(tc, HTIM2, htime2); > + d2l_write(tc, VTIM2, vtime2); > + > + d2l_write(tc, VFUEN, 0x00000001); > + d2l_write(tc, SYSRST, 0x00000004); > + d2l_write(tc, LVPHY0, 0x00040006); > + > + /* default jeida-24 */ > + if (bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_SPWG) { > + /* vesa-24, TODO jeida-18*/ > + d2l_write(tc, LV_MX0003, LV_MX(LVI_R0, LVI_R1, LVI_R2, LVI_R3)); > + d2l_write(tc, LV_MX0407, LV_MX(LVI_R4, LVI_R7, LVI_R5, LVI_G0)); > + d2l_write(tc, LV_MX0811, LV_MX(LVI_G1, LVI_G2, LVI_G6, LVI_G7)); > + d2l_write(tc, LV_MX1215, LV_MX(LVI_G3, LVI_G4, LVI_G5, LVI_B0)); > + d2l_write(tc, LV_MX1619, LV_MX(LVI_B6, LVI_B7, LVI_B1, LVI_B2)); > + d2l_write(tc, LV_MX2023, LV_MX(LVI_B3, LVI_B4, LVI_B5, LVI_L0)); > + d2l_write(tc, LV_MX2427, LV_MX(LVI_HS, LVI_VS, LVI_DE, LVI_R6)); > + } > + > + d2l_write(tc, VFUEN, 0x00000001); > + > + val = TC358775_LVCFG_PCLKDIV(DIVIDE_BY_3) | LVCFG_LVEN_BIT; > + if (tc->dual_link) > + val |= TC358775_LVCFG_LVDLINK(1); > + > + d2l_write(tc, LVCFG, val); > + > + drm_panel_enable(tc->panel); > +} > + > +static int tc_connector_get_modes(struct drm_connector *connector) > +{ > + struct tc_data *tc = connector_to_tc(connector); > + struct edid *edid; > + unsigned int count; > + > + if (tc->panel && tc->panel->funcs && tc->panel->funcs->get_modes) { > + count = tc->panel->funcs->get_modes(tc->panel, connector); > + if (count > 0) > + return count; > + } > + > + edid = drm_get_edid(connector, tc->i2c->adapter); > + if (!edid) > + return 0; > + > + drm_connector_update_edid_property(connector, edid); > + count = drm_add_edid_modes(connector, edid); > + kfree(edid); > + > + return count; > +} > + > +static int tc_connector_mode_valid(struct drm_connector *connector, > + struct drm_display_mode *mode) > +{ > + struct tc_data *tc = connector_to_tc(connector); > + > + /* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */ > + if ((mode->clock > 135000 && tc->dual_link == 0) || > + (mode->clock > 270000 && tc->dual_link == 1)) > + return MODE_CLOCK_HIGH; > + > + return MODE_OK; > +} As Laurent pointed out earlier this should be bridge.mode_valid. Regards Andrzej > + > +static struct drm_encoder * > +tc_connector_best_encoder(struct drm_connector *connector) > +{ > + struct tc_data *tc = connector_to_tc(connector); > + > + return tc->bridge.encoder; > +} > + > +static const struct drm_connector_helper_funcs tc_connector_helper_funcs = { > + .get_modes = tc_connector_get_modes, > + .mode_valid = tc_connector_mode_valid, > + .best_encoder = tc_connector_best_encoder, > +}; > + > +static const struct drm_connector_funcs tc_connector_funcs = { > + .fill_modes = drm_helper_probe_single_connector_modes, > + .destroy = drm_connector_cleanup, > + .reset = drm_atomic_helper_connector_reset, > + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, > + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, > +}; > + > +int tc358775_parse_dt(struct device_node *np, struct tc_data *tc) > +{ > + u32 num_lanes; > + u8 dual_link; > + > + of_property_read_u8(np, "tc,dual-link", &dual_link); > + of_property_read_u32(np, "tc,dsi-lanes", &num_lanes); > + > + if (num_lanes < 1 || num_lanes > 4) > + return -EINVAL; > + > + tc->num_dsi_lanes = num_lanes; > + tc->dual_link = dual_link; > + > + tc->host_node = of_graph_get_remote_node(np, 0, 0); > + if (!tc->host_node) > + return -ENODEV; > + > + of_node_put(tc->host_node); > + > + return 0; > +} > + > +int tc358775_attach_dsi(struct tc_data *tc) > +{ > + struct device *dev = &tc->i2c->dev; > + struct mipi_dsi_host *host; > + struct mipi_dsi_device *dsi; > + int ret = 0; > + const struct mipi_dsi_device_info info = { .type = "tc358775", > + .channel = 0, > + .node = NULL, > + }; > + > + host = of_find_mipi_dsi_host_by_node(tc->host_node); > + if (!host) { > + dev_err(dev, "failed to find dsi host\n"); > + return -EPROBE_DEFER; > + } > + > + dsi = mipi_dsi_device_register_full(host, &info); > + if (IS_ERR(dsi)) { > + dev_err(dev, "failed to create dsi device\n"); > + ret = PTR_ERR(dsi); > + goto err_dsi_device; > + } > + > + tc->dsi = dsi; > + > + dsi->lanes = tc->num_dsi_lanes; > + dsi->format = MIPI_DSI_FMT_RGB888; > + dsi->mode_flags = MIPI_DSI_MODE_VIDEO; > + > + ret = mipi_dsi_attach(dsi); > + if (ret < 0) { > + dev_err(dev, "failed to attach dsi to host\n"); > + goto err_dsi_attach; > + } > + > + return 0; > + > +err_dsi_attach: > + mipi_dsi_device_unregister(dsi); > +err_dsi_device: > + return ret; > +} > + > +static int tc_bridge_attach(struct drm_bridge *bridge) > +{ > + struct tc_data *tc = bridge_to_tc(bridge); > + struct drm_device *drm = bridge->dev; > + int ret; > + > + /* Create LVDS connector */ > + drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs); > + ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs, > + DRM_MODE_CONNECTOR_LVDS); > + if (ret) > + return ret; > + > + if (tc->panel) > + drm_panel_attach(tc->panel, &tc->connector); > + > + drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder); > + > + ret = tc358775_attach_dsi(tc); > + > + return ret; > +} > + > +static const struct drm_bridge_funcs tc_bridge_funcs = { > + .attach = tc_bridge_attach, > + .pre_enable = tc_bridge_pre_enable, > + .enable = tc_bridge_enable, > + .disable = tc_bridge_disable, > + .post_disable = tc_bridge_post_disable, > +}; > + > +static const struct regmap_config tc_regmap_config = { > + .name = "tc358775", > + .reg_bits = 16, > + .val_bits = 32, > + .reg_stride = 4, > + .max_register = 0x05A8, > + .cache_type = REGCACHE_RBTREE, > + .reg_format_endian = REGMAP_ENDIAN_BIG, > + .val_format_endian = REGMAP_ENDIAN_LITTLE, > +}; > + > +static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id) > +{ > + struct device *dev = &client->dev; > + struct tc_data *tc; > + int ret; > + unsigned int i; > + > + tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL); > + if (!tc) > + return -ENOMEM; > + > + tc->dev = dev; > + tc->i2c = client; > + tc->status = connector_status_connected; > + > + /* port@1 is the output port */ > + ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &tc->panel, NULL); > + if (ret && ret != -ENODEV) > + return ret; > + > + ret = tc358775_parse_dt(dev->of_node, tc); > + if (ret) > + return ret; > + > + for (i = 0; i < ARRAY_SIZE(tc->supplies); i++) > + tc->supplies[i].supply = regulator_names[i]; > + > + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(tc->supplies), > + tc->supplies); > + if (ret < 0) > + dev_err(dev, "failed to init regulator, ret=%d\n", ret); > + > + tc->stby_gpio = devm_gpiod_get(dev, "stby", GPIOD_OUT_HIGH); > + if (IS_ERR(tc->stby_gpio)) { > + ret = PTR_ERR(tc->stby_gpio); > + dev_err(dev, "cannot get stby-gpio %d\n", ret); > + return ret; > + } > + > + tc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); > + if (IS_ERR(tc->reset_gpio)) { > + ret = PTR_ERR(tc->reset_gpio); > + dev_err(dev, "cannot get reset-gpios %d\n", ret); > + return ret; > + } > + > + tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config); > + if (IS_ERR(tc->regmap)) { > + ret = PTR_ERR(tc->regmap); > + dev_err(dev, "Failed to initialize regmap: %d\n", ret); > + return ret; > + } > + > + tc->bridge.funcs = &tc_bridge_funcs; > + tc->bridge.of_node = dev->of_node; > + drm_bridge_add(&tc->bridge); > + > + i2c_set_clientdata(client, tc); > + > + return 0; > +} > + > +static int tc_remove(struct i2c_client *client) > +{ > + struct tc_data *tc = i2c_get_clientdata(client); > + > + drm_bridge_remove(&tc->bridge); > + > + return 0; > +} > + > +static const struct i2c_device_id tc358775_i2c_ids[] = { > + { "tc358775", 0 }, > + { } > +}; > +MODULE_DEVICE_TABLE(i2c, tc358775_i2c_ids); > + > +static const struct of_device_id tc358775_of_ids[] = { > + { .compatible = "toshiba,tc358775", }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, tc358775_of_ids); > + > +static struct i2c_driver tc358775_driver = { > + .driver = { > + .name = "tc358775", > + .of_match_table = tc358775_of_ids, > + }, > + .id_table = tc358775_i2c_ids, > + .probe = tc_probe, > + .remove = tc_remove, > +}; > +module_i2c_driver(tc358775_driver); > + > +MODULE_AUTHOR("Vinay Simha BN <vinaysimha@inforcecomputing.com>"); > +MODULE_DESCRIPTION("tc358775 LVDS encoder driver"); Please fix the description, for example: TC... DSI/LVDS bridge driver Regards Andrzej > +MODULE_LICENSE("GPL v2"); ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings 2020-03-11 9:48 ` [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings Vinay Simha BN 2020-03-11 9:48 ` [PATCH 2/2] display/drm/bridge: tc358775 DSI/LVDS driver Vinay Simha BN @ 2020-03-12 10:34 ` Andrzej Hajda 2020-03-12 14:33 ` Laurent Pinchart 2020-03-12 15:17 ` Rob Herring 3 siblings, 0 replies; 10+ messages in thread From: Andrzej Hajda @ 2020-03-12 10:34 UTC (permalink / raw) To: Vinay Simha BN, Laurent Pinchart Cc: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, David Airlie, open list, open list:DRM DRIVERS, Rob Herring Hi Vinay, Next time add patch version to de subject of email. On 11.03.2020 10:48, Vinay Simha BN wrote: > Add yaml documentation for DSI/LVDS tc358775 bridge > > Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> > > --- > v1: > Initial version > --- > .../bindings/display/bridge/toshiba-tc358775.yaml | 174 +++++++++++++++++++++ > 1 file changed, 174 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > > diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml b/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > new file mode 100644 > index 0000000..e9a9544 > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > @@ -0,0 +1,174 @@ > +# SPDX-License-Identifier: GPL-2.0 > +%YAML 1.2 > +--- > +$id: https://protect2.fireeye.com/url?k=cc9be7f9-9155e4b4-cc9a6cb6-000babff24ad-2a6ce73e1e41d358&u=http://devicetree.org/schemas/display/bridge/toshiba-tc358775.yaml# > +$schema: https://protect2.fireeye.com/url?k=293d6151-74f3621c-293cea1e-000babff24ad-793c0a803cb80d71&u=http://devicetree.org/meta-schemas/core.yaml# > + > + > +title: Toshiba TC358775 DSI to LVDS bridge bindings > + > +maintainers: > + - Vinay Simha BN <simhavcs@gmail.com> > + > +description: | > + This binding supports DSI to LVDS bridge TC358775 > + > +properties: > + compatible: > + const: toshiba,tc358775 > + > + reg: > + maxItems: 1 > + description: i2c address of the bridge, 0x0f > + > + tc, dsi-lanes: 1 > + maxItems: 1 > + description: Number of DSI data lanes connected to the DSI host. It should > + be one of 1, 2, 3 or 4. > + > + tc, dual-link: 1 > + maxItems: 1 > + description: To configure the LVDS transmitter either as single-link or dual-link. As Laurent commented earlier, it would be better to use two ports. See for example for input LVDS ports in: Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt Both should be defined in bindings but the 2nd can be optional in dts. Regards Andrzej > + > + vdd-supply: > + maxItems: 1 > + description: 1.2V LVDS Power Supply > + > + vddio-supply: > + maxItems: 1 > + description: 1.8V IO Power Supply > + > + stby-gpios: > + maxItems: 1 > + description: Standby pin, Low active > + > + reset-gpios: > + maxItems: 1 > + description: Hardware reset, Low active > + > + ports: > + type: object > + > + properties: > + port@0: > + type: object > + description: | > + DSI Input. The remote endpoint phandle should be a > + reference to a valid mipi_dsi_host device node. > + port@1: > + type: object > + description: | > + Video port for LVDS output (panel or connector). > + > + required: > + - port@0 > + - port@1 > + > +required: > + - compatible > + - reg > + - dsi-lanes > + - vdd-supply > + - vddio-supply > + - stby-gpios > + - reset-gpios > + - ports > + > +examples: > + - | > + i2c@78b8000 { > + /* On High speed expansion */ > + label = "HS-I2C2"; > + status = "okay"; > + > + tc_bridge: bridge@f { > + status = "okay"; > + > + compatible = "toshiba,tc358775"; > + reg = <0x0f>; > + > + tc,dsi-lanes = <4>; > + tc,dual-link = <0>; > + > + vdd-supply = <&pm8916_l2>; > + vddio-supply = <&pm8916_l6>; > + > + stby-gpio = <&msmgpio 99 GPIO_ACTIVE_LOW>; > + reset-gpio = <&msmgpio 72 GPIO_ACTIVE_LOW>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + d2l_in: endpoint { > + remote-endpoint = <&dsi0_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + d2l_out: endpoint { > + remote-endpoint = <&panel_in>; > + }; > + }; > + }; > + }; > + }; > + > + panel: auo,b101xtn01 { > + status = "okay"; > + compatible = "auo,b101xtn01", "panel-lvds"; > + power-supply = <&pm8916_l14>; > + > + width-mm = <223>; > + height-mm = <125>; > + > + data-mapping = "jeida-24"; > + > + panel-timing { > + /* 1366x768 @60Hz */ > + clock-frequency = <72000000>; > + hactive = <1366>; > + vactive = <768>; > + hsync-len = <70>; > + hfront-porch = <20>; > + hback-porch = <0>; > + vsync-len = <42>; > + vfront-porch = <14>; > + vback-porch = <0>; > + }; > + > + port { > + panel_in: endpoint { > + remote-endpoint = <&d2l_out>; > + }; > + }; > + }; > + > + mdss@1a00000 { > + status = "okay"; > + > + mdp@1a01000 { > + status = "okay"; > + }; > + > + dsi@1a98000 { > + status = "okay"; > + .. > + ports { > + port@1 { > + dsi0_out: endpoint { > + remote-endpoint = <&d2l_in>; > + data-lanes = <0 1 2 3>; > + }; > + }; > + }; > + }; > + > + dsi-phy@1a98300 { > + status = "okay"; > + .. > + }; > + }; ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings 2020-03-11 9:48 ` [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings Vinay Simha BN 2020-03-11 9:48 ` [PATCH 2/2] display/drm/bridge: tc358775 DSI/LVDS driver Vinay Simha BN 2020-03-12 10:34 ` [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings Andrzej Hajda @ 2020-03-12 14:33 ` Laurent Pinchart 2020-03-12 15:17 ` Rob Herring 3 siblings, 0 replies; 10+ messages in thread From: Laurent Pinchart @ 2020-03-12 14:33 UTC (permalink / raw) To: Vinay Simha BN Cc: Andrzej Hajda, David Airlie, Daniel Vetter, Rob Herring, open list:DRM DRIVERS, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, open list Hello Vinay, Please take into account the review comments from v1. We can discuss them in replies to v1 if you have any question. I'll skip reviewing this version. On Wed, Mar 11, 2020 at 03:18:24PM +0530, Vinay Simha BN wrote: > Add yaml documentation for DSI/LVDS tc358775 bridge > > Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> > > --- > v1: > Initial version > --- > .../bindings/display/bridge/toshiba-tc358775.yaml | 174 +++++++++++++++++++++ > 1 file changed, 174 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > > diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml b/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > new file mode 100644 > index 0000000..e9a9544 > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > @@ -0,0 +1,174 @@ > +# SPDX-License-Identifier: GPL-2.0 > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/display/bridge/toshiba-tc358775.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > + > +title: Toshiba TC358775 DSI to LVDS bridge bindings > + > +maintainers: > + - Vinay Simha BN <simhavcs@gmail.com> > + > +description: | > + This binding supports DSI to LVDS bridge TC358775 > + > +properties: > + compatible: > + const: toshiba,tc358775 > + > + reg: > + maxItems: 1 > + description: i2c address of the bridge, 0x0f > + > + tc, dsi-lanes: 1 > + maxItems: 1 > + description: Number of DSI data lanes connected to the DSI host. It should > + be one of 1, 2, 3 or 4. > + > + tc, dual-link: 1 > + maxItems: 1 > + description: To configure the LVDS transmitter either as single-link or dual-link. > + > + vdd-supply: > + maxItems: 1 > + description: 1.2V LVDS Power Supply > + > + vddio-supply: > + maxItems: 1 > + description: 1.8V IO Power Supply > + > + stby-gpios: > + maxItems: 1 > + description: Standby pin, Low active > + > + reset-gpios: > + maxItems: 1 > + description: Hardware reset, Low active > + > + ports: > + type: object > + > + properties: > + port@0: > + type: object > + description: | > + DSI Input. The remote endpoint phandle should be a > + reference to a valid mipi_dsi_host device node. > + port@1: > + type: object > + description: | > + Video port for LVDS output (panel or connector). > + > + required: > + - port@0 > + - port@1 > + > +required: > + - compatible > + - reg > + - dsi-lanes > + - vdd-supply > + - vddio-supply > + - stby-gpios > + - reset-gpios > + - ports > + > +examples: > + - | > + i2c@78b8000 { > + /* On High speed expansion */ > + label = "HS-I2C2"; > + status = "okay"; > + > + tc_bridge: bridge@f { > + status = "okay"; > + > + compatible = "toshiba,tc358775"; > + reg = <0x0f>; > + > + tc,dsi-lanes = <4>; > + tc,dual-link = <0>; > + > + vdd-supply = <&pm8916_l2>; > + vddio-supply = <&pm8916_l6>; > + > + stby-gpio = <&msmgpio 99 GPIO_ACTIVE_LOW>; > + reset-gpio = <&msmgpio 72 GPIO_ACTIVE_LOW>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + d2l_in: endpoint { > + remote-endpoint = <&dsi0_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + d2l_out: endpoint { > + remote-endpoint = <&panel_in>; > + }; > + }; > + }; > + }; > + }; > + > + panel: auo,b101xtn01 { > + status = "okay"; > + compatible = "auo,b101xtn01", "panel-lvds"; > + power-supply = <&pm8916_l14>; > + > + width-mm = <223>; > + height-mm = <125>; > + > + data-mapping = "jeida-24"; > + > + panel-timing { > + /* 1366x768 @60Hz */ > + clock-frequency = <72000000>; > + hactive = <1366>; > + vactive = <768>; > + hsync-len = <70>; > + hfront-porch = <20>; > + hback-porch = <0>; > + vsync-len = <42>; > + vfront-porch = <14>; > + vback-porch = <0>; > + }; > + > + port { > + panel_in: endpoint { > + remote-endpoint = <&d2l_out>; > + }; > + }; > + }; > + > + mdss@1a00000 { > + status = "okay"; > + > + mdp@1a01000 { > + status = "okay"; > + }; > + > + dsi@1a98000 { > + status = "okay"; > + .. > + ports { > + port@1 { > + dsi0_out: endpoint { > + remote-endpoint = <&d2l_in>; > + data-lanes = <0 1 2 3>; > + }; > + }; > + }; > + }; > + > + dsi-phy@1a98300 { > + status = "okay"; > + .. > + }; > + }; -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings 2020-03-11 9:48 ` [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings Vinay Simha BN ` (2 preceding siblings ...) 2020-03-12 14:33 ` Laurent Pinchart @ 2020-03-12 15:17 ` Rob Herring 2020-03-15 15:24 ` Vinay Simha B N 3 siblings, 1 reply; 10+ messages in thread From: Rob Herring @ 2020-03-12 15:17 UTC (permalink / raw) To: Vinay Simha BN Cc: Andrzej Hajda, Laurent Pinchart, Vinay Simha BN, David Airlie, Daniel Vetter, open list:DRM DRIVERS, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, open list On Wed, 11 Mar 2020 15:18:24 +0530, Vinay Simha BN wrote: > Add yaml documentation for DSI/LVDS tc358775 bridge > > Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> > > --- > v1: > Initial version > --- > .../bindings/display/bridge/toshiba-tc358775.yaml | 174 +++++++++++++++++++++ > 1 file changed, 174 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > My bot found errors running 'make dt_binding_check' on your patch: Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml: while scanning for the next token found character that cannot start any token in "<unicode string>", line 11, column 1 Documentation/devicetree/bindings/Makefile:12: recipe for target 'Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.example.dts' failed make[1]: *** [Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.example.dts] Error 1 make[1]: *** Waiting for unfinished jobs.... warning: no schema found in file: Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml: ignoring, error parsing file Makefile:1262: recipe for target 'dt_binding_check' failed make: *** [dt_binding_check] Error 2 See https://patchwork.ozlabs.org/patch/1252753 Please check and re-submit. ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings 2020-03-12 15:17 ` Rob Herring @ 2020-03-15 15:24 ` Vinay Simha B N 2020-03-17 6:55 ` Vinay Simha B N 0 siblings, 1 reply; 10+ messages in thread From: Vinay Simha B N @ 2020-03-15 15:24 UTC (permalink / raw) To: Rob Herring Cc: Andrzej Hajda, Laurent Pinchart, David Airlie, Daniel Vetter, open list:DRM DRIVERS, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, open list rob, i do not get the error when running 'make dt_binding_check' in my build environment Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml is there any tool available similar to scripts/checkpatch.pl -f <file> , for yaml files? On Thu, Mar 12, 2020 at 8:47 PM Rob Herring <robh@kernel.org> wrote: > > On Wed, 11 Mar 2020 15:18:24 +0530, Vinay Simha BN wrote: > > Add yaml documentation for DSI/LVDS tc358775 bridge > > > > Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> > > > > --- > > v1: > > Initial version > > --- > > .../bindings/display/bridge/toshiba-tc358775.yaml | 174 +++++++++++++++++++++ > > 1 file changed, 174 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > > > > My bot found errors running 'make dt_binding_check' on your patch: > > Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml: while scanning for the next token > found character that cannot start any token > in "<unicode string>", line 11, column 1 > Documentation/devicetree/bindings/Makefile:12: recipe for target 'Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.example.dts' failed > make[1]: *** [Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.example.dts] Error 1 > make[1]: *** Waiting for unfinished jobs.... > warning: no schema found in file: Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml: ignoring, error parsing file > Makefile:1262: recipe for target 'dt_binding_check' failed > make: *** [dt_binding_check] Error 2 > > See https://patchwork.ozlabs.org/patch/1252753 > Please check and re-submit. -- regards, vinaysimha ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings 2020-03-15 15:24 ` Vinay Simha B N @ 2020-03-17 6:55 ` Vinay Simha B N 2020-03-17 14:27 ` Sam Ravnborg 0 siblings, 1 reply; 10+ messages in thread From: Vinay Simha B N @ 2020-03-17 6:55 UTC (permalink / raw) To: Sam Ravnborg Cc: Andrzej Hajda, Laurent Pinchart, David Airlie, Daniel Vetter, open list:DRM DRIVERS, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, open list, Rob Herring sam, i need some inputs on the below error. I had created this file Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml by using vim editor. Do we have any tool to create yaml file? i do not get the error when running 'make dt_binding_check' in my build environment Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml is there any tool available similar to scripts/checkpatch.pl -f <file> , for yaml files? On Sun, Mar 15, 2020 at 8:54 PM Vinay Simha B N <simhavcs@gmail.com> wrote: > > rob, > > i do not get the error when running 'make dt_binding_check' in my > build environment > Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > > is there any tool available similar to scripts/checkpatch.pl -f > <file> , for yaml files? > > On Thu, Mar 12, 2020 at 8:47 PM Rob Herring <robh@kernel.org> wrote: > > > > On Wed, 11 Mar 2020 15:18:24 +0530, Vinay Simha BN wrote: > > > Add yaml documentation for DSI/LVDS tc358775 bridge > > > > > > Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> > > > > > > --- > > > v1: > > > Initial version > > > --- > > > .../bindings/display/bridge/toshiba-tc358775.yaml | 174 +++++++++++++++++++++ > > > 1 file changed, 174 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > > > > > > > My bot found errors running 'make dt_binding_check' on your patch: > > > > Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml: while scanning for the next token > > found character that cannot start any token > > in "<unicode string>", line 11, column 1 > > Documentation/devicetree/bindings/Makefile:12: recipe for target 'Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.example.dts' failed > > make[1]: *** [Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.example.dts] Error 1 > > make[1]: *** Waiting for unfinished jobs.... > > warning: no schema found in file: Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > > /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml: ignoring, error parsing file > > Makefile:1262: recipe for target 'dt_binding_check' failed > > make: *** [dt_binding_check] Error 2 > > > > See https://patchwork.ozlabs.org/patch/1252753 > > Please check and re-submit. > > > > -- > regards, > vinaysimha -- regards, vinaysimha ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings 2020-03-17 6:55 ` Vinay Simha B N @ 2020-03-17 14:27 ` Sam Ravnborg 2020-06-08 10:38 ` Vinay Simha B N 0 siblings, 1 reply; 10+ messages in thread From: Sam Ravnborg @ 2020-03-17 14:27 UTC (permalink / raw) To: Vinay Simha B N Cc: Andrzej Hajda, Laurent Pinchart, David Airlie, Daniel Vetter, open list:DRM DRIVERS, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, open list, Rob Herring Hi Vinay. On Tue, Mar 17, 2020 at 12:25:42PM +0530, Vinay Simha B N wrote: > sam, > > i need some inputs on the below error. I had created this file > Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > by using vim editor. Do we have any tool to create yaml file? I use vim myself, but is careful to follow the right syntax. > > i do not get the error when running 'make dt_binding_check' in my > build environment > Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > > is there any tool available similar to scripts/checkpatch.pl -f > <file> , for yaml files? Please read Documentation/devicetree/writing-schema. Here you can find general info + instruction how to install the tools required for "make dt_binding_check". I could reproduce the error reported by Rob. I gave your binding file a shot - there were a lot of smaller issues: - do not use tabs in yaml files - be consistent in indent - vendor prefixed properties needed some extra care - example was full of bugs - "..." - no need for status = "okay"; - properties spelled wrong For the example I adjusted it to use indent of 4 spaces, which IMO is more readable than the two spaces used in the other parts of the file. I have attached the updated binding file - please review and fix. This is just a quick shot, I did not do a proper review. Please rename the file, other files in same dir are named "toshiba,xxx", so replace '-' with ','. And try to introduce bugs in the example - and check that the tooling catches the bug. hint: make DT=.../foo.yaml dt_binding_check is a qucik way to check only your binding. And for new bindings the preferred license is: (GPL-2.0-only OR BSD-2-Clause) Sam # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- $id: http://devicetree.org/schemas/display/bridge/toshiba-tc358775.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# title: Toshiba TC358775 DSI to LVDS bridge bindings maintainers: - Vinay Simha BN <simhavcs@gmail.com> description: | This binding supports DSI to LVDS bridge TC358775 properties: compatible: const: toshiba,tc358775 reg: maxItems: 1 description: i2c address of the bridge, 0x0f toshiba,dsi-lanes: allOf: - $ref: /schemas/types.yaml#/definitions/uint32 - minimum: 1 maximum: 4 default: 1 description: bla bla toshiba,dual-link: $ref: /schemas/types.yaml#definitions/flag description: bla bla vdd-supply: maxItems: 1 description: 1.2V LVDS Power Supply vddio-supply: maxItems: 1 description: 1.8V IO Power Supply stby-gpios: maxItems: 1 description: Standby pin, Low active reset-gpios: maxItems: 1 description: Hardware reset, Low active ports: type: object properties: port@0: type: object description: | DSI Input. The remote endpoint phandle should be a reference to a valid mipi_dsi_host device node. port@1: type: object description: | Video port for LVDS output (panel or connector). required: - port@0 - port@1 required: - compatible - reg - tc,dsi-lanes - vdd-supply - vddio-supply - stby-gpios - reset-gpios - ports examples: - |+ #include <dt-bindings/gpio/gpio.h> i2c@78b8000 { #address-cells = <1>; #size-cells = <0>; /* On High speed expansion */ label = "HS-I2C2"; status = "okay"; tc_bridge: bridge@f { compatible = "toshiba,tc358775"; reg = <0x0f>; tc,dsi-lanes = <4>; tc,dual-link = <0>; vdd-supply = <&pm8916_l2>; vddio-supply = <&pm8916_l6>; stby-gpios = <&msmgpio 99 GPIO_ACTIVE_LOW>; reset-gpios = <&msmgpio 72 GPIO_ACTIVE_LOW>; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; d2l_in: endpoint { remote-endpoint = <&dsi0_out>; }; }; port@1 { reg = <1>; d2l_out: endpoint { remote-endpoint = <&panel_in>; }; }; }; }; }; panel: auo,b101xtn01 { status = "okay"; compatible = "auo,b101xtn01", "panel-lvds"; power-supply = <&pm8916_l14>; width-mm = <223>; height-mm = <125>; data-mapping = "jeida-24"; panel-timing { /* 1366x768 @60Hz */ clock-frequency = <72000000>; hactive = <1366>; vactive = <768>; hsync-len = <70>; hfront-porch = <20>; hback-porch = <0>; vsync-len = <42>; vfront-porch = <14>; vback-porch = <0>; }; port { panel_in: endpoint { remote-endpoint = <&d2l_out>; }; }; }; mdss { dsi@1a98000 { ports { port@1 { dsi0_out: endpoint { remote-endpoint = <&d2l_in>; data-lanes = <0 1 2 3>; }; }; }; }; }; ... ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings 2020-03-17 14:27 ` Sam Ravnborg @ 2020-06-08 10:38 ` Vinay Simha B N 0 siblings, 0 replies; 10+ messages in thread From: Vinay Simha B N @ 2020-06-08 10:38 UTC (permalink / raw) To: Sam Ravnborg Cc: Andrzej Hajda, Laurent Pinchart, David Airlie, Daniel Vetter, open list:DRM DRIVERS, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, open list, Rob Herring sam, This is my latest yaml file https://github.com/vinaysimhabn/kernel-msm/blob/5.6.0-rc3-d2l-wip/Documentation/devicetree/bindings/display/bridge/toshiba%2Ctc358775.yaml make CROSS_COMPILE=$TC64 ARCH=arm64 DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.yaml dt_binding_check i am getting these errors Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.example.dt.yaml: lvds-out: 'data-mapping', 'height-mm', 'panel-timing', 'width-mm' do not match any of the regexes: 'pinctrl-[0-9]+' Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.example.dt.yaml: lvds-out: compatible: Additional items are not allowed ('panel-lvds' was unexpected) Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.example.dt.yaml: lvds-out: compatible: ['auo,b101xtn01', 'panel-lvds'] is too long Please suggest how to add the references of panel/lvds.yaml or panel/panel-common.yaml and panel/advantech,idk-2121wr.yaml in my yaml file. On Tue, Mar 17, 2020 at 7:57 PM Sam Ravnborg <sam@ravnborg.org> wrote: > > Hi Vinay. > > On Tue, Mar 17, 2020 at 12:25:42PM +0530, Vinay Simha B N wrote: > > sam, > > > > i need some inputs on the below error. I had created this file > > Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > > by using vim editor. Do we have any tool to create yaml file? > > I use vim myself, but is careful to follow the right syntax. > > > > > i do not get the error when running 'make dt_binding_check' in my > > build environment > > Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml > > > > is there any tool available similar to scripts/checkpatch.pl -f > > <file> , for yaml files? > > Please read Documentation/devicetree/writing-schema. > Here you can find general info + instruction how to install the tools > required for "make dt_binding_check". > > I could reproduce the error reported by Rob. > I gave your binding file a shot - there were a lot of smaller issues: > > - do not use tabs in yaml files > - be consistent in indent > - vendor prefixed properties needed some extra care > - example was full of bugs > - "..." > - no need for status = "okay"; > - properties spelled wrong > > For the example I adjusted it to use indent of 4 spaces, which IMO > is more readable than the two spaces used in the other parts of the > file. > > I have attached the updated binding file - please review and fix. > This is just a quick shot, I did not do a proper review. > > Please rename the file, other files in same dir are named "toshiba,xxx", > so replace '-' with ','. > > And try to introduce bugs in the example - and check that the tooling > catches the bug. > > hint: > > make DT=.../foo.yaml dt_binding_check > > is a qucik way to check only your binding. > > And for new bindings the preferred license is: (GPL-2.0-only OR BSD-2-Clause) > > Sam > > # SPDX-License-Identifier: GPL-2.0 > %YAML 1.2 > --- > $id: http://devicetree.org/schemas/display/bridge/toshiba-tc358775.yaml# > $schema: http://devicetree.org/meta-schemas/core.yaml# > > > title: Toshiba TC358775 DSI to LVDS bridge bindings > > maintainers: > - Vinay Simha BN <simhavcs@gmail.com> > > description: | > This binding supports DSI to LVDS bridge TC358775 > > properties: > compatible: > const: toshiba,tc358775 > > reg: > maxItems: 1 > description: i2c address of the bridge, 0x0f > > toshiba,dsi-lanes: > allOf: > - $ref: /schemas/types.yaml#/definitions/uint32 > - minimum: 1 > maximum: 4 > default: 1 > description: bla bla > > toshiba,dual-link: > $ref: /schemas/types.yaml#definitions/flag > description: bla bla > > vdd-supply: > maxItems: 1 > description: 1.2V LVDS Power Supply > > vddio-supply: > maxItems: 1 > description: 1.8V IO Power Supply > > stby-gpios: > maxItems: 1 > description: Standby pin, Low active > > reset-gpios: > maxItems: 1 > description: Hardware reset, Low active > > ports: > type: object > > properties: > port@0: > type: object > description: | > DSI Input. The remote endpoint phandle should be a > reference to a valid mipi_dsi_host device node. > port@1: > type: object > description: | > Video port for LVDS output (panel or connector). > > required: > - port@0 > - port@1 > > required: > - compatible > - reg > - tc,dsi-lanes > - vdd-supply > - vddio-supply > - stby-gpios > - reset-gpios > - ports > > examples: > - |+ > #include <dt-bindings/gpio/gpio.h> > > i2c@78b8000 { > #address-cells = <1>; > #size-cells = <0>; > > /* On High speed expansion */ > label = "HS-I2C2"; > status = "okay"; > > tc_bridge: bridge@f { > compatible = "toshiba,tc358775"; > reg = <0x0f>; > > tc,dsi-lanes = <4>; > tc,dual-link = <0>; > > vdd-supply = <&pm8916_l2>; > vddio-supply = <&pm8916_l6>; > > stby-gpios = <&msmgpio 99 GPIO_ACTIVE_LOW>; > reset-gpios = <&msmgpio 72 GPIO_ACTIVE_LOW>; > > ports { > #address-cells = <1>; > #size-cells = <0>; > > port@0 { > reg = <0>; > d2l_in: endpoint { > remote-endpoint = <&dsi0_out>; > }; > }; > > port@1 { > reg = <1>; > d2l_out: endpoint { > remote-endpoint = <&panel_in>; > }; > }; > }; > }; > }; > > panel: auo,b101xtn01 { > status = "okay"; > compatible = "auo,b101xtn01", "panel-lvds"; > power-supply = <&pm8916_l14>; > > width-mm = <223>; > height-mm = <125>; > > data-mapping = "jeida-24"; > > panel-timing { > /* 1366x768 @60Hz */ > clock-frequency = <72000000>; > hactive = <1366>; > vactive = <768>; > hsync-len = <70>; > hfront-porch = <20>; > hback-porch = <0>; > vsync-len = <42>; > vfront-porch = <14>; > vback-porch = <0>; > }; > > port { > panel_in: endpoint { > remote-endpoint = <&d2l_out>; > }; > }; > }; > > mdss { > dsi@1a98000 { > ports { > port@1 { > dsi0_out: endpoint { > remote-endpoint = <&d2l_in>; > data-lanes = <0 1 2 3>; > }; > }; > }; > }; > }; > > ... -- regards, vinaysimha ^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2020-06-08 10:38 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <CGME20200312080849eucas1p2ebc25fb87cc917986ba0f268272ef2ed@eucas1p2.samsung.com>
2020-03-11 9:48 ` [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings Vinay Simha BN
2020-03-11 9:48 ` [PATCH 2/2] display/drm/bridge: tc358775 DSI/LVDS driver Vinay Simha BN
2020-03-12 10:50 ` Andrzej Hajda
2020-03-12 10:34 ` [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings Andrzej Hajda
2020-03-12 14:33 ` Laurent Pinchart
2020-03-12 15:17 ` Rob Herring
2020-03-15 15:24 ` Vinay Simha B N
2020-03-17 6:55 ` Vinay Simha B N
2020-03-17 14:27 ` Sam Ravnborg
2020-06-08 10:38 ` Vinay Simha B N
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).