* [PATCH v6 0/4] Add QMP V3 USB3 PHY support for SC7180
@ 2020-04-28 14:06 Sandeep Maheswaram
2020-04-28 14:06 ` [PATCH v6 1/4] dt-bindings: phy: qcom,qmp: Convert QMP PHY bindings to yaml Sandeep Maheswaram
` (3 more replies)
0 siblings, 4 replies; 7+ messages in thread
From: Sandeep Maheswaram @ 2020-04-28 14:06 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Kishon Vijay Abraham I, Rob Herring,
Mark Rutland, Stephen Boyd, Doug Anderson, Matthias Kaehlcke
Cc: linux-arm-msm, linux-kernel, devicetree, Manu Gautam, Sandeep Maheswaram
Add QMP V3 USB3 PHY entries for SC7180 in phy driver and
device tree bindings.
changes in v6:
*Added separate yaml file for USB3 DP PHY bindings.
changes in v5:
*Addressed comments from Matthias in yaml file.
*Dropped PATCH 4/4 as it is landed in linux-next.
changes in v4:
*Addressed comments from Matthias and Rob in yaml file.
changes in v3:
*Addressed Rob's comments in yaml file.
*Sepearated the SC7180 support in yaml patch.
*corrected the phy reset entries in device tree.
changes in v2:
*Remove global phy reset in QMP PHY.
*Convert QMP PHY bindings to yaml.
Sandeep Maheswaram (4):
dt-bindings: phy: qcom,qmp: Convert QMP PHY bindings to yaml
dt-bindings: phy: qcom,qmp-usb3-dp: Add dt bindings for USB3 DP PHY
dt-bindings: phy: qcom,qmp-usb3-dp: Add support for SC7180
phy: qcom-qmp: Add QMP V3 USB3 PHY support for SC7180
.../devicetree/bindings/phy/qcom,qmp-phy.yaml | 311 +++++++++++++++++++++
.../bindings/phy/qcom,qmp-usb3-dp-phy.yaml | 136 +++++++++
.../devicetree/bindings/phy/qcom-qmp-phy.txt | 242 ----------------
drivers/phy/qualcomm/phy-qcom-qmp.c | 38 +++
4 files changed, 485 insertions(+), 242 deletions(-)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
create mode 100644 Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml
delete mode 100644 Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v6 1/4] dt-bindings: phy: qcom,qmp: Convert QMP PHY bindings to yaml
2020-04-28 14:06 [PATCH v6 0/4] Add QMP V3 USB3 PHY support for SC7180 Sandeep Maheswaram
@ 2020-04-28 14:06 ` Sandeep Maheswaram
2020-04-29 19:06 ` Matthias Kaehlcke
2020-04-28 14:06 ` [PATCH v6 2/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add dt bindings for USB3 DP PHY Sandeep Maheswaram
` (2 subsequent siblings)
3 siblings, 1 reply; 7+ messages in thread
From: Sandeep Maheswaram @ 2020-04-28 14:06 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Kishon Vijay Abraham I, Rob Herring,
Mark Rutland, Stephen Boyd, Doug Anderson, Matthias Kaehlcke
Cc: linux-arm-msm, linux-kernel, devicetree, Manu Gautam, Sandeep Maheswaram
Convert QMP PHY bindings to DT schema format using json-schema.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/phy/qcom,qmp-phy.yaml | 311 +++++++++++++++++++++
.../devicetree/bindings/phy/qcom-qmp-phy.txt | 242 ----------------
2 files changed, 311 insertions(+), 242 deletions(-)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
delete mode 100644 Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
new file mode 100644
index 0000000..7da2be6
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
@@ -0,0 +1,311 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/qcom,qmp-phy.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm QMP PHY controller
+
+maintainers:
+ - Manu Gautam <mgautam@codeaurora.org>
+
+description:
+ QMP phy controller supports physical layer functionality for a number of
+ controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
+
+properties:
+ compatible:
+ enum:
+ - qcom,ipq8074-qmp-pcie-phy
+ - qcom,msm8996-qmp-pcie-phy
+ - qcom,msm8996-qmp-ufs-phy
+ - qcom,msm8996-qmp-usb3-phy
+ - qcom,msm8998-qmp-pcie-phy
+ - qcom,msm8998-qmp-ufs-phy
+ - qcom,msm8998-qmp-usb3-phy
+ - qcom,sdm845-qhp-pcie-phy
+ - qcom,sdm845-qmp-pcie-phy
+ - qcom,sdm845-qmp-ufs-phy
+ - qcom,sdm845-qmp-usb3-uni-phy
+ - qcom,sm8150-qmp-ufs-phy
+
+ reg:
+ items:
+ - description: Address and length of PHY's common serdes block.
+
+ "#clock-cells":
+ enum: [ 1, 2 ]
+
+ "#address-cells":
+ enum: [ 1, 2 ]
+
+ "#size-cells":
+ enum: [ 1, 2 ]
+
+ clocks:
+ minItems: 1
+ maxItems: 4
+
+ clock-names:
+ minItems: 1
+ maxItems: 4
+
+ resets:
+ minItems: 1
+ maxItems: 3
+
+ reset-names:
+ minItems: 1
+ maxItems: 3
+
+ vdda-phy-supply:
+ description:
+ Phandle to a regulator supply to PHY core block.
+
+ vdda-pll-supply:
+ description:
+ Phandle to 1.8V regulator supply to PHY refclk pll block.
+
+ vddp-ref-clk-supply:
+ description:
+ Phandle to a regulator supply to any specific refclk
+ pll block.
+
+#Required nodes:
+patternProperties:
+ "^phy@[0-9a-f]+$":
+ type: object
+ description:
+ Each device node of QMP phy is required to have as many child nodes as
+ the number of lanes the PHY has.
+
+required:
+ - compatible
+ - reg
+ - "#clock-cells"
+ - "#address-cells"
+ - "#size-cells"
+ - clocks
+ - clock-names
+ - resets
+ - reset-names
+ - vdda-phy-supply
+ - vdda-pll-supply
+
+additionalProperties: false
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,sdm845-qmp-usb3-uni-phy
+ then:
+ properties:
+ clocks:
+ items:
+ - description: Phy aux clock.
+ - description: Phy config clock.
+ - description: 19.2 MHz ref clk.
+ - description: Phy common block aux clock.
+ clock-names:
+ items:
+ - const: aux
+ - const: cfg_ahb
+ - const: ref
+ - const: com_aux
+ resets:
+ items:
+ - description: reset of phy block.
+ - description: phy common block reset.
+ reset-names:
+ items:
+ - const: phy
+ - const: common
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,msm8996-qmp-pcie-phy
+ then:
+ properties:
+ clocks:
+ items:
+ - description: Phy aux clock.
+ - description: Phy config clock.
+ - description: 19.2 MHz ref clk.
+ clock-names:
+ items:
+ - const: aux
+ - const: cfg_ahb
+ - const: ref
+ resets:
+ items:
+ - description: reset of phy block.
+ - description: phy common block reset.
+ - description: phy's ahb cfg block reset.
+ reset-names:
+ items:
+ - const: phy
+ - const: common
+ - const: cfg
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,msm8996-qmp-usb3-phy
+ - qcom,msm8998-qmp-pcie-phy
+ - qcom,msm8998-qmp-usb3-phy
+ then:
+ properties:
+ clocks:
+ items:
+ - description: Phy aux clock.
+ - description: Phy config clock.
+ - description: 19.2 MHz ref clk.
+ clock-names:
+ items:
+ - const: aux
+ - const: cfg_ahb
+ - const: ref
+ resets:
+ items:
+ - description: reset of phy block.
+ - description: phy common block reset.
+ reset-names:
+ items:
+ - const: phy
+ - const: common
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,msm8996-qmp-ufs-phy
+ then:
+ properties:
+ clocks:
+ items:
+ - description: 19.2 MHz ref clk.
+ clock-names:
+ items:
+ - const: ref
+ resets:
+ items:
+ - description: PHY reset in the UFS controller.
+ reset-names:
+ items:
+ - const: ufsphy
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,msm8998-qmp-ufs-phy
+ - qcom,sdm845-qmp-ufs-phy
+ - qcom,sm8150-qmp-ufs-phy
+ then:
+ properties:
+ clocks:
+ items:
+ - description: 19.2 MHz ref clk.
+ - description: Phy reference aux clock.
+ clock-names:
+ items:
+ - const: ref
+ - const: ref_aux
+ resets:
+ items:
+ - description: PHY reset in the UFS controller.
+ reset-names:
+ items:
+ - const: ufsphy
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,ipq8074-qmp-pcie-phy
+ then:
+ properties:
+ clocks:
+ items:
+ - description: pipe clk.
+ clock-names:
+ items:
+ - const: pipe_clk
+ resets:
+ items:
+ - description: reset of phy block.
+ - description: phy common block reset.
+ reset-names:
+ items:
+ - const: phy
+ - const: common
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,sdm845-qhp-pcie-phy
+ - qcom,sdm845-qmp-pcie-phy
+ then:
+ properties:
+ clocks:
+ items:
+ - description: Phy aux clock.
+ - description: Phy config clock.
+ - description: 19.2 MHz ref clk.
+ - description: Phy refgen clk.
+ clock-names:
+ items:
+ - const: aux
+ - const: cfg_ahb
+ - const: ref
+ - const: refgen
+ resets:
+ items:
+ - description: reset of phy block.
+ reset-names:
+ items:
+ - const: phy
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+ usb_2_qmpphy: phy-wrapper@88eb000 {
+ compatible = "qcom,sdm845-qmp-usb3-uni-phy";
+ reg = <0 0x088eb000 0 0x18c>;
+ #clock-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
+ <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_USB3_SEC_CLKREF_CLK>,
+ <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "com_aux";
+
+ resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
+ <&gcc GCC_USB3_PHY_SEC_BCR>;
+ reset-names = "phy", "common";
+
+ vdda-phy-supply = <&vdda_usb2_ss_1p2>;
+ vdda-pll-supply = <&vdda_usb2_ss_core>;
+
+ usb_2_ssphy: phy@88eb200 {
+ reg = <0 0x088eb200 0 0x128>,
+ <0 0x088eb400 0 0x1fc>,
+ <0 0x088eb800 0 0x218>,
+ <0 0x088eb600 0 0x70>;
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_uni_phy_pipe_clk_src";
+ };
+ };
diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
deleted file mode 100644
index 54d6f8d..0000000
--- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
+++ /dev/null
@@ -1,242 +0,0 @@
-Qualcomm QMP PHY controller
-===========================
-
-QMP phy controller supports physical layer functionality for a number of
-controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
-
-Required properties:
- - compatible: compatible list, contains:
- "qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074
- "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
- "qcom,msm8996-qmp-ufs-phy" for 14nm UFS phy on msm8996,
- "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996,
- "qcom,msm8998-qmp-usb3-phy" for USB3 QMP V3 phy on msm8998,
- "qcom,msm8998-qmp-ufs-phy" for UFS QMP phy on msm8998,
- "qcom,msm8998-qmp-pcie-phy" for PCIe QMP phy on msm8998,
- "qcom,sdm845-qhp-pcie-phy" for QHP PCIe phy on sdm845,
- "qcom,sdm845-qmp-pcie-phy" for QMP PCIe phy on sdm845,
- "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845,
- "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845,
- "qcom,sdm845-qmp-ufs-phy" for UFS QMP phy on sdm845,
- "qcom,sm8150-qmp-ufs-phy" for UFS QMP phy on sm8150.
-
-- reg:
- - index 0: address and length of register set for PHY's common
- serdes block.
- - index 1: address and length of the DP_COM control block (for
- "qcom,sdm845-qmp-usb3-phy" only).
-
-- reg-names:
- - For "qcom,sdm845-qmp-usb3-phy":
- - Should be: "reg-base", "dp_com"
- - For all others:
- - The reg-names property shouldn't be defined.
-
- - #address-cells: must be 1
- - #size-cells: must be 1
- - ranges: must be present
-
- - clocks: a list of phandles and clock-specifier pairs,
- one for each entry in clock-names.
- - clock-names: "cfg_ahb" for phy config clock,
- "aux" for phy aux clock,
- "ref" for 19.2 MHz ref clk,
- "com_aux" for phy common block aux clock,
- "ref_aux" for phy reference aux clock,
-
- For "qcom,ipq8074-qmp-pcie-phy": no clocks are listed.
- For "qcom,msm8996-qmp-pcie-phy" must contain:
- "aux", "cfg_ahb", "ref".
- For "qcom,msm8996-qmp-ufs-phy" must contain:
- "ref".
- For "qcom,msm8996-qmp-usb3-phy" must contain:
- "aux", "cfg_ahb", "ref".
- For "qcom,msm8998-qmp-usb3-phy" must contain:
- "aux", "cfg_ahb", "ref".
- For "qcom,msm8998-qmp-ufs-phy" must contain:
- "ref", "ref_aux".
- For "qcom,msm8998-qmp-pcie-phy" must contain:
- "aux", "cfg_ahb", "ref".
- For "qcom,sdm845-qhp-pcie-phy" must contain:
- "aux", "cfg_ahb", "ref", "refgen".
- For "qcom,sdm845-qmp-pcie-phy" must contain:
- "aux", "cfg_ahb", "ref", "refgen".
- For "qcom,sdm845-qmp-usb3-phy" must contain:
- "aux", "cfg_ahb", "ref", "com_aux".
- For "qcom,sdm845-qmp-usb3-uni-phy" must contain:
- "aux", "cfg_ahb", "ref", "com_aux".
- For "qcom,sdm845-qmp-ufs-phy" must contain:
- "ref", "ref_aux".
- For "qcom,sm8150-qmp-ufs-phy" must contain:
- "ref", "ref_aux".
-
- - resets: a list of phandles and reset controller specifier pairs,
- one for each entry in reset-names.
- - reset-names: "phy" for reset of phy block,
- "common" for phy common block reset,
- "cfg" for phy's ahb cfg block reset,
- "ufsphy" for the PHY reset in the UFS controller.
-
- For "qcom,ipq8074-qmp-pcie-phy" must contain:
- "phy", "common".
- For "qcom,msm8996-qmp-pcie-phy" must contain:
- "phy", "common", "cfg".
- For "qcom,msm8996-qmp-ufs-phy": must contain:
- "ufsphy".
- For "qcom,msm8996-qmp-usb3-phy" must contain
- "phy", "common".
- For "qcom,msm8998-qmp-usb3-phy" must contain
- "phy", "common".
- For "qcom,msm8998-qmp-ufs-phy": must contain:
- "ufsphy".
- For "qcom,msm8998-qmp-pcie-phy" must contain:
- "phy", "common".
- For "qcom,sdm845-qhp-pcie-phy" must contain:
- "phy".
- For "qcom,sdm845-qmp-pcie-phy" must contain:
- "phy".
- For "qcom,sdm845-qmp-usb3-phy" must contain:
- "phy", "common".
- For "qcom,sdm845-qmp-usb3-uni-phy" must contain:
- "phy", "common".
- For "qcom,sdm845-qmp-ufs-phy": must contain:
- "ufsphy".
- For "qcom,sm8150-qmp-ufs-phy": must contain:
- "ufsphy".
-
- - vdda-phy-supply: Phandle to a regulator supply to PHY core block.
- - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
-
-Optional properties:
- - vddp-ref-clk-supply: Phandle to a regulator supply to any specific refclk
- pll block.
-
-Required nodes:
- - Each device node of QMP phy is required to have as many child nodes as
- the number of lanes the PHY has.
-
-Required properties for child nodes of PCIe PHYs (one child per lane):
- - reg: list of offset and length pairs of register sets for PHY blocks -
- tx, rx, pcs, and pcs_misc (optional).
- - #phy-cells: must be 0
-
-Required properties for a single "lanes" child node of non-PCIe PHYs:
- - reg: list of offset and length pairs of register sets for PHY blocks
- For 1-lane devices:
- tx, rx, pcs, and (optionally) pcs_misc
- For 2-lane devices:
- tx0, rx0, pcs, tx1, rx1, and (optionally) pcs_misc
- - #phy-cells: must be 0
-
-Required properties for child node of PCIe and USB3 qmp phys:
- - clocks: a list of phandles and clock-specifier pairs,
- one for each entry in clock-names.
- - clock-names: Must contain following:
- "pipe<lane-number>" for pipe clock specific to each lane.
- - clock-output-names: Name of the PHY clock that will be the parent for
- the above pipe clock.
- For "qcom,ipq8074-qmp-pcie-phy":
- - "pcie20_phy0_pipe_clk" Pipe Clock parent
- (or)
- "pcie20_phy1_pipe_clk"
- - #clock-cells: must be 0
- - Phy pll outputs pipe clocks for pipe based PHYs. These clocks are then
- gate-controlled by the gcc.
-
-Required properties for child node of PHYs with lane reset, AKA:
- "qcom,msm8996-qmp-pcie-phy"
- - resets: a list of phandles and reset controller specifier pairs,
- one for each entry in reset-names.
- - reset-names: Must contain following:
- "lane<lane-number>" for reset specific to each lane.
-
-Example:
- phy@34000 {
- compatible = "qcom,msm8996-qmp-pcie-phy";
- reg = <0x34000 0x488>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
- <&gcc GCC_PCIE_PHY_CFG_AHB_CLK>,
- <&gcc GCC_PCIE_CLKREF_CLK>;
- clock-names = "aux", "cfg_ahb", "ref";
-
- vdda-phy-supply = <&pm8994_l28>;
- vdda-pll-supply = <&pm8994_l12>;
-
- resets = <&gcc GCC_PCIE_PHY_BCR>,
- <&gcc GCC_PCIE_PHY_COM_BCR>,
- <&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>;
- reset-names = "phy", "common", "cfg";
-
- pciephy_0: lane@35000 {
- reg = <0x35000 0x130>,
- <0x35200 0x200>,
- <0x35400 0x1dc>;
- #clock-cells = <0>;
- #phy-cells = <0>;
-
- clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
- clock-names = "pipe0";
- clock-output-names = "pcie_0_pipe_clk_src";
- resets = <&gcc GCC_PCIE_0_PHY_BCR>;
- reset-names = "lane0";
- };
-
- pciephy_1: lane@36000 {
- ...
- ...
- };
-
- phy@88eb000 {
- compatible = "qcom,sdm845-qmp-usb3-uni-phy";
- reg = <0x88eb000 0x18c>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
- <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
- <&gcc GCC_USB3_SEC_CLKREF_CLK>,
- <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
- clock-names = "aux", "cfg_ahb", "ref", "com_aux";
-
- resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
- <&gcc GCC_USB3_PHY_SEC_BCR>;
- reset-names = "phy", "common";
-
- lane@88eb200 {
- reg = <0x88eb200 0x128>,
- <0x88eb400 0x1fc>,
- <0x88eb800 0x218>,
- <0x88eb600 0x70>;
- #clock-cells = <0>;
- #phy-cells = <0>;
- clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
- clock-names = "pipe0";
- clock-output-names = "usb3_uni_phy_pipe_clk_src";
- };
- };
-
- phy@1d87000 {
- compatible = "qcom,sdm845-qmp-ufs-phy";
- reg = <0x1d87000 0x18c>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- clock-names = "ref",
- "ref_aux";
- clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
- <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
-
- lanes@1d87400 {
- reg = <0x1d87400 0x108>,
- <0x1d87600 0x1e0>,
- <0x1d87c00 0x1dc>,
- <0x1d87800 0x108>,
- <0x1d87a00 0x1e0>;
- #phy-cells = <0>;
- };
- };
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v6 2/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add dt bindings for USB3 DP PHY
2020-04-28 14:06 [PATCH v6 0/4] Add QMP V3 USB3 PHY support for SC7180 Sandeep Maheswaram
2020-04-28 14:06 ` [PATCH v6 1/4] dt-bindings: phy: qcom,qmp: Convert QMP PHY bindings to yaml Sandeep Maheswaram
@ 2020-04-28 14:06 ` Sandeep Maheswaram
2020-04-29 18:59 ` Matthias Kaehlcke
2020-04-28 14:06 ` [PATCH v6 3/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add support for SC7180 Sandeep Maheswaram
2020-04-28 14:06 ` [PATCH v6 4/4] phy: qcom-qmp: Add QMP V3 USB3 PHY " Sandeep Maheswaram
3 siblings, 1 reply; 7+ messages in thread
From: Sandeep Maheswaram @ 2020-04-28 14:06 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Kishon Vijay Abraham I, Rob Herring,
Mark Rutland, Stephen Boyd, Doug Anderson, Matthias Kaehlcke
Cc: linux-arm-msm, linux-kernel, devicetree, Manu Gautam, Sandeep Maheswaram
Split out the dt bindings for USB3 DP PHY from qcom,qmp bindings
for modularity.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
---
.../bindings/phy/qcom,qmp-usb3-dp-phy.yaml | 135 +++++++++++++++++++++
1 file changed, 135 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml
diff --git a/Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml
new file mode 100644
index 0000000..6055786
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml
@@ -0,0 +1,135 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/qcom,qmp-usb3-dp-phy.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm QMP USB3 DP PHY controller
+
+maintainers:
+ - Manu Gautam <mgautam@codeaurora.org>
+
+properties:
+ compatible:
+ const:
+ qcom,sdm845-qmp-usb3-phy
+ reg:
+ items:
+ - description: Address and length of PHY's common serdes block.
+ - description: Address and length of the DP_COM control block.
+
+ reg-names:
+ items:
+ - const: reg-base
+ - const: dp_com
+
+ "#clock-cells":
+ enum: [ 1, 2 ]
+
+ "#address-cells":
+ enum: [ 1, 2 ]
+
+ "#size-cells":
+ enum: [ 1, 2 ]
+
+ clocks:
+ items:
+ - description: Phy aux clock.
+ - description: Phy config clock.
+ - description: 19.2 MHz ref clk.
+ - description: Phy common block aux clock.
+
+ clock-names:
+ items:
+ - const: aux
+ - const: cfg_ahb
+ - const: ref
+ - const: com_aux
+
+ resets:
+ items:
+ - description: reset of phy block.
+ - description: phy common block reset.
+
+ reset-names:
+ items:
+ - const: phy
+ - const: common
+
+ vdda-phy-supply:
+ description:
+ Phandle to a regulator supply to PHY core block.
+
+ vdda-pll-supply:
+ description:
+ Phandle to 1.8V regulator supply to PHY refclk pll block.
+
+ vddp-ref-clk-supply:
+ description:
+ Phandle to a regulator supply to any specific refclk
+ pll block.
+
+#Required nodes:
+patternProperties:
+ "^phy@[0-9a-f]+$":
+ type: object
+ description:
+ Each device node of QMP phy is required to have as many child nodes as
+ the number of lanes the PHY has.
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - "#clock-cells"
+ - "#address-cells"
+ - "#size-cells"
+ - clocks
+ - clock-names
+ - resets
+ - reset-names
+ - vdda-phy-supply
+ - vdda-pll-supply
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+ usb_1_qmpphy: phy-wrapper@88e9000 {
+ compatible = "qcom,sdm845-qmp-usb3-phy";
+ reg = <0 0x088e9000 0 0x18c>,
+ <0 0x088e8000 0 0x10>;
+ reg-names = "reg-base", "dp_com";
+ #clock-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+ <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+ <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "com_aux";
+
+ resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
+ <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
+ reset-names = "phy", "common";
+
+ vdda-phy-supply = <&vdda_usb2_ss_1p2>;
+ vdda-pll-supply = <&vdda_usb2_ss_core>;
+
+ usb_1_ssphy: phy@88e9200 {
+ reg = <0 0x088e9200 0 0x128>,
+ <0 0x088e9400 0 0x200>,
+ <0 0x088e9c00 0 0x218>,
+ <0 0x088e9600 0 0x128>,
+ <0 0x088e9800 0 0x200>,
+ <0 0x088e9a00 0 0x100>;
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_phy_pipe_clk_src";
+ };
+ };
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v6 3/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add support for SC7180
2020-04-28 14:06 [PATCH v6 0/4] Add QMP V3 USB3 PHY support for SC7180 Sandeep Maheswaram
2020-04-28 14:06 ` [PATCH v6 1/4] dt-bindings: phy: qcom,qmp: Convert QMP PHY bindings to yaml Sandeep Maheswaram
2020-04-28 14:06 ` [PATCH v6 2/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add dt bindings for USB3 DP PHY Sandeep Maheswaram
@ 2020-04-28 14:06 ` Sandeep Maheswaram
2020-04-28 14:06 ` [PATCH v6 4/4] phy: qcom-qmp: Add QMP V3 USB3 PHY " Sandeep Maheswaram
3 siblings, 0 replies; 7+ messages in thread
From: Sandeep Maheswaram @ 2020-04-28 14:06 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Kishon Vijay Abraham I, Rob Herring,
Mark Rutland, Stephen Boyd, Doug Anderson, Matthias Kaehlcke
Cc: linux-arm-msm, linux-kernel, devicetree, Manu Gautam, Sandeep Maheswaram
Add compatible for SC7180 in QMP USB3 DP PHY bindings.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
---
Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml
index 6055786..b770e63 100644
--- a/Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml
@@ -12,8 +12,9 @@ maintainers:
properties:
compatible:
- const:
- qcom,sdm845-qmp-usb3-phy
+ enum:
+ - qcom,sc7180-qmp-usb3-phy
+ - qcom,sdm845-qmp-usb3-phy
reg:
items:
- description: Address and length of PHY's common serdes block.
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v6 4/4] phy: qcom-qmp: Add QMP V3 USB3 PHY support for SC7180
2020-04-28 14:06 [PATCH v6 0/4] Add QMP V3 USB3 PHY support for SC7180 Sandeep Maheswaram
` (2 preceding siblings ...)
2020-04-28 14:06 ` [PATCH v6 3/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add support for SC7180 Sandeep Maheswaram
@ 2020-04-28 14:06 ` Sandeep Maheswaram
3 siblings, 0 replies; 7+ messages in thread
From: Sandeep Maheswaram @ 2020-04-28 14:06 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Kishon Vijay Abraham I, Rob Herring,
Mark Rutland, Stephen Boyd, Doug Anderson, Matthias Kaehlcke
Cc: linux-arm-msm, linux-kernel, devicetree, Manu Gautam, Sandeep Maheswaram
Adding QMP v3 USB3 PHY support for SC7180.
Adding only usb phy reset in the list to avoid
reset of DP block.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
drivers/phy/qualcomm/phy-qcom-qmp.c | 38 +++++++++++++++++++++++++++++++++++++
1 file changed, 38 insertions(+)
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index c190406..d9d3e2f 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -1458,6 +1458,10 @@ static const char * const msm8996_usb3phy_reset_l[] = {
"phy", "common",
};
+static const char * const sc7180_usb3phy_reset_l[] = {
+ "phy",
+};
+
static const char * const sdm845_pciephy_reset_l[] = {
"phy",
};
@@ -1671,6 +1675,37 @@ static const struct qmp_phy_cfg qmp_v3_usb3phy_cfg = {
.is_dual_lane_phy = true,
};
+static const struct qmp_phy_cfg sc7180_usb3phy_cfg = {
+ .type = PHY_TYPE_USB3,
+ .nlanes = 1,
+
+ .serdes_tbl = qmp_v3_usb3_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(qmp_v3_usb3_serdes_tbl),
+ .tx_tbl = qmp_v3_usb3_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_tx_tbl),
+ .rx_tbl = qmp_v3_usb3_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_rx_tbl),
+ .pcs_tbl = qmp_v3_usb3_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(qmp_v3_usb3_pcs_tbl),
+ .clk_list = qmp_v3_phy_clk_l,
+ .num_clks = ARRAY_SIZE(qmp_v3_phy_clk_l),
+ .reset_list = sc7180_usb3phy_reset_l,
+ .num_resets = ARRAY_SIZE(sc7180_usb3phy_reset_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
+ .regs = qmp_v3_usb3phy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN,
+
+ .has_pwrdn_delay = true,
+ .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
+ .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
+
+ .has_phy_dp_com_ctrl = true,
+ .is_dual_lane_phy = true,
+};
+
static const struct qmp_phy_cfg qmp_v3_usb3_uniphy_cfg = {
.type = PHY_TYPE_USB3,
.nlanes = 1,
@@ -2516,6 +2551,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
.compatible = "qcom,ipq8074-qmp-pcie-phy",
.data = &ipq8074_pciephy_cfg,
}, {
+ .compatible = "qcom,sc7180-qmp-usb3-phy",
+ .data = &sc7180_usb3phy_cfg,
+ }, {
.compatible = "qcom,sdm845-qhp-pcie-phy",
.data = &sdm845_qhp_pciephy_cfg,
}, {
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v6 2/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add dt bindings for USB3 DP PHY
2020-04-28 14:06 ` [PATCH v6 2/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add dt bindings for USB3 DP PHY Sandeep Maheswaram
@ 2020-04-29 18:59 ` Matthias Kaehlcke
0 siblings, 0 replies; 7+ messages in thread
From: Matthias Kaehlcke @ 2020-04-29 18:59 UTC (permalink / raw)
To: Sandeep Maheswaram
Cc: Andy Gross, Bjorn Andersson, Kishon Vijay Abraham I, Rob Herring,
Mark Rutland, Stephen Boyd, Doug Anderson, linux-arm-msm,
linux-kernel, devicetree, Manu Gautam
Hi Sandeep,
This is a bit misleading/confusing. Patch "1/4] dt-bindings: phy: qcom,qmp:
Convert QMP PHY bindings to yaml" does the conversion to yaml AND removes
the binding for USB3 DP PHY, then this patch adds it again. Patches should
be self-contained and their commit messages shouldn't omit important details.
If the first patch is applied in isolation the USB3 DP PHY binding disappears
silently, supposedly with the approval from Rob, who reviewed an earlier
version of the patch without the removal.
I think there are two options:
1) one patch with the (complete) conversion to a single yaml file, plus
a separate patch that moves the DP PHY binding to its own file
2) a single patch which does the conversion to yaml and moves the DP PHY
binding to its own file
IMO 1) is slightly better, but both should be ok.
Thanks
Matthias
On Tue, Apr 28, 2020 at 07:36:13PM +0530, Sandeep Maheswaram wrote:
> Split out the dt bindings for USB3 DP PHY from qcom,qmp bindings
> for modularity.
>
> Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
> ---
> .../bindings/phy/qcom,qmp-usb3-dp-phy.yaml | 135 +++++++++++++++++++++
> 1 file changed, 135 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml
>
> diff --git a/Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml
> new file mode 100644
> index 0000000..6055786
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml
> @@ -0,0 +1,135 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/phy/qcom,qmp-usb3-dp-phy.yaml#"
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> +
> +title: Qualcomm QMP USB3 DP PHY controller
> +
> +maintainers:
> + - Manu Gautam <mgautam@codeaurora.org>
> +
> +properties:
> + compatible:
> + const:
> + qcom,sdm845-qmp-usb3-phy
> + reg:
> + items:
> + - description: Address and length of PHY's common serdes block.
> + - description: Address and length of the DP_COM control block.
> +
> + reg-names:
> + items:
> + - const: reg-base
> + - const: dp_com
> +
> + "#clock-cells":
> + enum: [ 1, 2 ]
> +
> + "#address-cells":
> + enum: [ 1, 2 ]
> +
> + "#size-cells":
> + enum: [ 1, 2 ]
> +
> + clocks:
> + items:
> + - description: Phy aux clock.
> + - description: Phy config clock.
> + - description: 19.2 MHz ref clk.
> + - description: Phy common block aux clock.
> +
> + clock-names:
> + items:
> + - const: aux
> + - const: cfg_ahb
> + - const: ref
> + - const: com_aux
> +
> + resets:
> + items:
> + - description: reset of phy block.
> + - description: phy common block reset.
> +
> + reset-names:
> + items:
> + - const: phy
> + - const: common
> +
> + vdda-phy-supply:
> + description:
> + Phandle to a regulator supply to PHY core block.
> +
> + vdda-pll-supply:
> + description:
> + Phandle to 1.8V regulator supply to PHY refclk pll block.
> +
> + vddp-ref-clk-supply:
> + description:
> + Phandle to a regulator supply to any specific refclk
> + pll block.
> +
> +#Required nodes:
> +patternProperties:
> + "^phy@[0-9a-f]+$":
> + type: object
> + description:
> + Each device node of QMP phy is required to have as many child nodes as
> + the number of lanes the PHY has.
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - "#clock-cells"
> + - "#address-cells"
> + - "#size-cells"
> + - clocks
> + - clock-names
> + - resets
> + - reset-names
> + - vdda-phy-supply
> + - vdda-pll-supply
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/qcom,gcc-sdm845.h>
> + usb_1_qmpphy: phy-wrapper@88e9000 {
> + compatible = "qcom,sdm845-qmp-usb3-phy";
> + reg = <0 0x088e9000 0 0x18c>,
> + <0 0x088e8000 0 0x10>;
> + reg-names = "reg-base", "dp_com";
> + #clock-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
> + <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
> + <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
> + <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
> + clock-names = "aux", "cfg_ahb", "ref", "com_aux";
> +
> + resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
> + <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
> + reset-names = "phy", "common";
> +
> + vdda-phy-supply = <&vdda_usb2_ss_1p2>;
> + vdda-pll-supply = <&vdda_usb2_ss_core>;
> +
> + usb_1_ssphy: phy@88e9200 {
> + reg = <0 0x088e9200 0 0x128>,
> + <0 0x088e9400 0 0x200>,
> + <0 0x088e9c00 0 0x218>,
> + <0 0x088e9600 0 0x128>,
> + <0 0x088e9800 0 0x200>,
> + <0 0x088e9a00 0 0x100>;
> + #clock-cells = <0>;
> + #phy-cells = <0>;
> + clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "usb3_phy_pipe_clk_src";
> + };
> + };
> --
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
> of Code Aurora Forum, hosted by The Linux Foundation
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v6 1/4] dt-bindings: phy: qcom,qmp: Convert QMP PHY bindings to yaml
2020-04-28 14:06 ` [PATCH v6 1/4] dt-bindings: phy: qcom,qmp: Convert QMP PHY bindings to yaml Sandeep Maheswaram
@ 2020-04-29 19:06 ` Matthias Kaehlcke
0 siblings, 0 replies; 7+ messages in thread
From: Matthias Kaehlcke @ 2020-04-29 19:06 UTC (permalink / raw)
To: Sandeep Maheswaram
Cc: Andy Gross, Bjorn Andersson, Kishon Vijay Abraham I, Rob Herring,
Mark Rutland, Stephen Boyd, Doug Anderson, linux-arm-msm,
linux-kernel, devicetree, Manu Gautam
On Tue, Apr 28, 2020 at 07:36:12PM +0530, Sandeep Maheswaram wrote:
> Convert QMP PHY bindings to DT schema format using json-schema.
NACK (not sure if that carries any weight ;-)
v6 of this patch removes the binding of USB3 DP PHY during the conversion,
which is then added again as .yaml by "[2/4] dt-bindings: phy: qcom,qmp-usb3-dp:
Add dt bindings for USB3 DP PHY" (https://patchwork.kernel.org/patch/11514767/).
See my reply on that patch for what to do instead.
> Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
> .../devicetree/bindings/phy/qcom,qmp-phy.yaml | 311 +++++++++++++++++++++
> .../devicetree/bindings/phy/qcom-qmp-phy.txt | 242 ----------------
> 2 files changed, 311 insertions(+), 242 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
> delete mode 100644 Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
>
> diff --git a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
> new file mode 100644
> index 0000000..7da2be6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
> @@ -0,0 +1,311 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/phy/qcom,qmp-phy.yaml#"
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> +
> +title: Qualcomm QMP PHY controller
> +
> +maintainers:
> + - Manu Gautam <mgautam@codeaurora.org>
> +
> +description:
> + QMP phy controller supports physical layer functionality for a number of
> + controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
> +
> +properties:
> + compatible:
> + enum:
> + - qcom,ipq8074-qmp-pcie-phy
> + - qcom,msm8996-qmp-pcie-phy
> + - qcom,msm8996-qmp-ufs-phy
> + - qcom,msm8996-qmp-usb3-phy
> + - qcom,msm8998-qmp-pcie-phy
> + - qcom,msm8998-qmp-ufs-phy
> + - qcom,msm8998-qmp-usb3-phy
> + - qcom,sdm845-qhp-pcie-phy
> + - qcom,sdm845-qmp-pcie-phy
> + - qcom,sdm845-qmp-ufs-phy
> + - qcom,sdm845-qmp-usb3-uni-phy
> + - qcom,sm8150-qmp-ufs-phy
> +
> + reg:
> + items:
> + - description: Address and length of PHY's common serdes block.
> +
> + "#clock-cells":
> + enum: [ 1, 2 ]
> +
> + "#address-cells":
> + enum: [ 1, 2 ]
> +
> + "#size-cells":
> + enum: [ 1, 2 ]
> +
> + clocks:
> + minItems: 1
> + maxItems: 4
> +
> + clock-names:
> + minItems: 1
> + maxItems: 4
> +
> + resets:
> + minItems: 1
> + maxItems: 3
> +
> + reset-names:
> + minItems: 1
> + maxItems: 3
> +
> + vdda-phy-supply:
> + description:
> + Phandle to a regulator supply to PHY core block.
> +
> + vdda-pll-supply:
> + description:
> + Phandle to 1.8V regulator supply to PHY refclk pll block.
> +
> + vddp-ref-clk-supply:
> + description:
> + Phandle to a regulator supply to any specific refclk
> + pll block.
> +
> +#Required nodes:
> +patternProperties:
> + "^phy@[0-9a-f]+$":
> + type: object
> + description:
> + Each device node of QMP phy is required to have as many child nodes as
> + the number of lanes the PHY has.
> +
> +required:
> + - compatible
> + - reg
> + - "#clock-cells"
> + - "#address-cells"
> + - "#size-cells"
> + - clocks
> + - clock-names
> + - resets
> + - reset-names
> + - vdda-phy-supply
> + - vdda-pll-supply
> +
> +additionalProperties: false
> +
> +allOf:
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - qcom,sdm845-qmp-usb3-uni-phy
> + then:
> + properties:
> + clocks:
> + items:
> + - description: Phy aux clock.
> + - description: Phy config clock.
> + - description: 19.2 MHz ref clk.
> + - description: Phy common block aux clock.
> + clock-names:
> + items:
> + - const: aux
> + - const: cfg_ahb
> + - const: ref
> + - const: com_aux
> + resets:
> + items:
> + - description: reset of phy block.
> + - description: phy common block reset.
> + reset-names:
> + items:
> + - const: phy
> + - const: common
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - qcom,msm8996-qmp-pcie-phy
> + then:
> + properties:
> + clocks:
> + items:
> + - description: Phy aux clock.
> + - description: Phy config clock.
> + - description: 19.2 MHz ref clk.
> + clock-names:
> + items:
> + - const: aux
> + - const: cfg_ahb
> + - const: ref
> + resets:
> + items:
> + - description: reset of phy block.
> + - description: phy common block reset.
> + - description: phy's ahb cfg block reset.
> + reset-names:
> + items:
> + - const: phy
> + - const: common
> + - const: cfg
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - qcom,msm8996-qmp-usb3-phy
> + - qcom,msm8998-qmp-pcie-phy
> + - qcom,msm8998-qmp-usb3-phy
> + then:
> + properties:
> + clocks:
> + items:
> + - description: Phy aux clock.
> + - description: Phy config clock.
> + - description: 19.2 MHz ref clk.
> + clock-names:
> + items:
> + - const: aux
> + - const: cfg_ahb
> + - const: ref
> + resets:
> + items:
> + - description: reset of phy block.
> + - description: phy common block reset.
> + reset-names:
> + items:
> + - const: phy
> + - const: common
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - qcom,msm8996-qmp-ufs-phy
> + then:
> + properties:
> + clocks:
> + items:
> + - description: 19.2 MHz ref clk.
> + clock-names:
> + items:
> + - const: ref
> + resets:
> + items:
> + - description: PHY reset in the UFS controller.
> + reset-names:
> + items:
> + - const: ufsphy
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - qcom,msm8998-qmp-ufs-phy
> + - qcom,sdm845-qmp-ufs-phy
> + - qcom,sm8150-qmp-ufs-phy
> + then:
> + properties:
> + clocks:
> + items:
> + - description: 19.2 MHz ref clk.
> + - description: Phy reference aux clock.
> + clock-names:
> + items:
> + - const: ref
> + - const: ref_aux
> + resets:
> + items:
> + - description: PHY reset in the UFS controller.
> + reset-names:
> + items:
> + - const: ufsphy
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - qcom,ipq8074-qmp-pcie-phy
> + then:
> + properties:
> + clocks:
> + items:
> + - description: pipe clk.
> + clock-names:
> + items:
> + - const: pipe_clk
> + resets:
> + items:
> + - description: reset of phy block.
> + - description: phy common block reset.
> + reset-names:
> + items:
> + - const: phy
> + - const: common
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - qcom,sdm845-qhp-pcie-phy
> + - qcom,sdm845-qmp-pcie-phy
> + then:
> + properties:
> + clocks:
> + items:
> + - description: Phy aux clock.
> + - description: Phy config clock.
> + - description: 19.2 MHz ref clk.
> + - description: Phy refgen clk.
> + clock-names:
> + items:
> + - const: aux
> + - const: cfg_ahb
> + - const: ref
> + - const: refgen
> + resets:
> + items:
> + - description: reset of phy block.
> + reset-names:
> + items:
> + - const: phy
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/qcom,gcc-sdm845.h>
> + usb_2_qmpphy: phy-wrapper@88eb000 {
> + compatible = "qcom,sdm845-qmp-usb3-uni-phy";
> + reg = <0 0x088eb000 0 0x18c>;
> + #clock-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
> + <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
> + <&gcc GCC_USB3_SEC_CLKREF_CLK>,
> + <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
> + clock-names = "aux", "cfg_ahb", "ref", "com_aux";
> +
> + resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
> + <&gcc GCC_USB3_PHY_SEC_BCR>;
> + reset-names = "phy", "common";
> +
> + vdda-phy-supply = <&vdda_usb2_ss_1p2>;
> + vdda-pll-supply = <&vdda_usb2_ss_core>;
> +
> + usb_2_ssphy: phy@88eb200 {
> + reg = <0 0x088eb200 0 0x128>,
> + <0 0x088eb400 0 0x1fc>,
> + <0 0x088eb800 0 0x218>,
> + <0 0x088eb600 0 0x70>;
> + #clock-cells = <0>;
> + #phy-cells = <0>;
> + clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "usb3_uni_phy_pipe_clk_src";
> + };
> + };
> diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
> deleted file mode 100644
> index 54d6f8d..0000000
> --- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
> +++ /dev/null
> @@ -1,242 +0,0 @@
> -Qualcomm QMP PHY controller
> -===========================
> -
> -QMP phy controller supports physical layer functionality for a number of
> -controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
> -
> -Required properties:
> - - compatible: compatible list, contains:
> - "qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074
> - "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
> - "qcom,msm8996-qmp-ufs-phy" for 14nm UFS phy on msm8996,
> - "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996,
> - "qcom,msm8998-qmp-usb3-phy" for USB3 QMP V3 phy on msm8998,
> - "qcom,msm8998-qmp-ufs-phy" for UFS QMP phy on msm8998,
> - "qcom,msm8998-qmp-pcie-phy" for PCIe QMP phy on msm8998,
> - "qcom,sdm845-qhp-pcie-phy" for QHP PCIe phy on sdm845,
> - "qcom,sdm845-qmp-pcie-phy" for QMP PCIe phy on sdm845,
> - "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845,
> - "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845,
> - "qcom,sdm845-qmp-ufs-phy" for UFS QMP phy on sdm845,
> - "qcom,sm8150-qmp-ufs-phy" for UFS QMP phy on sm8150.
> -
> -- reg:
> - - index 0: address and length of register set for PHY's common
> - serdes block.
> - - index 1: address and length of the DP_COM control block (for
> - "qcom,sdm845-qmp-usb3-phy" only).
> -
> -- reg-names:
> - - For "qcom,sdm845-qmp-usb3-phy":
> - - Should be: "reg-base", "dp_com"
> - - For all others:
> - - The reg-names property shouldn't be defined.
> -
> - - #address-cells: must be 1
> - - #size-cells: must be 1
> - - ranges: must be present
> -
> - - clocks: a list of phandles and clock-specifier pairs,
> - one for each entry in clock-names.
> - - clock-names: "cfg_ahb" for phy config clock,
> - "aux" for phy aux clock,
> - "ref" for 19.2 MHz ref clk,
> - "com_aux" for phy common block aux clock,
> - "ref_aux" for phy reference aux clock,
> -
> - For "qcom,ipq8074-qmp-pcie-phy": no clocks are listed.
> - For "qcom,msm8996-qmp-pcie-phy" must contain:
> - "aux", "cfg_ahb", "ref".
> - For "qcom,msm8996-qmp-ufs-phy" must contain:
> - "ref".
> - For "qcom,msm8996-qmp-usb3-phy" must contain:
> - "aux", "cfg_ahb", "ref".
> - For "qcom,msm8998-qmp-usb3-phy" must contain:
> - "aux", "cfg_ahb", "ref".
> - For "qcom,msm8998-qmp-ufs-phy" must contain:
> - "ref", "ref_aux".
> - For "qcom,msm8998-qmp-pcie-phy" must contain:
> - "aux", "cfg_ahb", "ref".
> - For "qcom,sdm845-qhp-pcie-phy" must contain:
> - "aux", "cfg_ahb", "ref", "refgen".
> - For "qcom,sdm845-qmp-pcie-phy" must contain:
> - "aux", "cfg_ahb", "ref", "refgen".
> - For "qcom,sdm845-qmp-usb3-phy" must contain:
> - "aux", "cfg_ahb", "ref", "com_aux".
> - For "qcom,sdm845-qmp-usb3-uni-phy" must contain:
> - "aux", "cfg_ahb", "ref", "com_aux".
> - For "qcom,sdm845-qmp-ufs-phy" must contain:
> - "ref", "ref_aux".
> - For "qcom,sm8150-qmp-ufs-phy" must contain:
> - "ref", "ref_aux".
> -
> - - resets: a list of phandles and reset controller specifier pairs,
> - one for each entry in reset-names.
> - - reset-names: "phy" for reset of phy block,
> - "common" for phy common block reset,
> - "cfg" for phy's ahb cfg block reset,
> - "ufsphy" for the PHY reset in the UFS controller.
> -
> - For "qcom,ipq8074-qmp-pcie-phy" must contain:
> - "phy", "common".
> - For "qcom,msm8996-qmp-pcie-phy" must contain:
> - "phy", "common", "cfg".
> - For "qcom,msm8996-qmp-ufs-phy": must contain:
> - "ufsphy".
> - For "qcom,msm8996-qmp-usb3-phy" must contain
> - "phy", "common".
> - For "qcom,msm8998-qmp-usb3-phy" must contain
> - "phy", "common".
> - For "qcom,msm8998-qmp-ufs-phy": must contain:
> - "ufsphy".
> - For "qcom,msm8998-qmp-pcie-phy" must contain:
> - "phy", "common".
> - For "qcom,sdm845-qhp-pcie-phy" must contain:
> - "phy".
> - For "qcom,sdm845-qmp-pcie-phy" must contain:
> - "phy".
> - For "qcom,sdm845-qmp-usb3-phy" must contain:
> - "phy", "common".
> - For "qcom,sdm845-qmp-usb3-uni-phy" must contain:
> - "phy", "common".
> - For "qcom,sdm845-qmp-ufs-phy": must contain:
> - "ufsphy".
> - For "qcom,sm8150-qmp-ufs-phy": must contain:
> - "ufsphy".
> -
> - - vdda-phy-supply: Phandle to a regulator supply to PHY core block.
> - - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
> -
> -Optional properties:
> - - vddp-ref-clk-supply: Phandle to a regulator supply to any specific refclk
> - pll block.
> -
> -Required nodes:
> - - Each device node of QMP phy is required to have as many child nodes as
> - the number of lanes the PHY has.
> -
> -Required properties for child nodes of PCIe PHYs (one child per lane):
> - - reg: list of offset and length pairs of register sets for PHY blocks -
> - tx, rx, pcs, and pcs_misc (optional).
> - - #phy-cells: must be 0
> -
> -Required properties for a single "lanes" child node of non-PCIe PHYs:
> - - reg: list of offset and length pairs of register sets for PHY blocks
> - For 1-lane devices:
> - tx, rx, pcs, and (optionally) pcs_misc
> - For 2-lane devices:
> - tx0, rx0, pcs, tx1, rx1, and (optionally) pcs_misc
> - - #phy-cells: must be 0
> -
> -Required properties for child node of PCIe and USB3 qmp phys:
> - - clocks: a list of phandles and clock-specifier pairs,
> - one for each entry in clock-names.
> - - clock-names: Must contain following:
> - "pipe<lane-number>" for pipe clock specific to each lane.
> - - clock-output-names: Name of the PHY clock that will be the parent for
> - the above pipe clock.
> - For "qcom,ipq8074-qmp-pcie-phy":
> - - "pcie20_phy0_pipe_clk" Pipe Clock parent
> - (or)
> - "pcie20_phy1_pipe_clk"
> - - #clock-cells: must be 0
> - - Phy pll outputs pipe clocks for pipe based PHYs. These clocks are then
> - gate-controlled by the gcc.
> -
> -Required properties for child node of PHYs with lane reset, AKA:
> - "qcom,msm8996-qmp-pcie-phy"
> - - resets: a list of phandles and reset controller specifier pairs,
> - one for each entry in reset-names.
> - - reset-names: Must contain following:
> - "lane<lane-number>" for reset specific to each lane.
> -
> -Example:
> - phy@34000 {
> - compatible = "qcom,msm8996-qmp-pcie-phy";
> - reg = <0x34000 0x488>;
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
> - <&gcc GCC_PCIE_PHY_CFG_AHB_CLK>,
> - <&gcc GCC_PCIE_CLKREF_CLK>;
> - clock-names = "aux", "cfg_ahb", "ref";
> -
> - vdda-phy-supply = <&pm8994_l28>;
> - vdda-pll-supply = <&pm8994_l12>;
> -
> - resets = <&gcc GCC_PCIE_PHY_BCR>,
> - <&gcc GCC_PCIE_PHY_COM_BCR>,
> - <&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>;
> - reset-names = "phy", "common", "cfg";
> -
> - pciephy_0: lane@35000 {
> - reg = <0x35000 0x130>,
> - <0x35200 0x200>,
> - <0x35400 0x1dc>;
> - #clock-cells = <0>;
> - #phy-cells = <0>;
> -
> - clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
> - clock-names = "pipe0";
> - clock-output-names = "pcie_0_pipe_clk_src";
> - resets = <&gcc GCC_PCIE_0_PHY_BCR>;
> - reset-names = "lane0";
> - };
> -
> - pciephy_1: lane@36000 {
> - ...
> - ...
> - };
> -
> - phy@88eb000 {
> - compatible = "qcom,sdm845-qmp-usb3-uni-phy";
> - reg = <0x88eb000 0x18c>;
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
> - <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
> - <&gcc GCC_USB3_SEC_CLKREF_CLK>,
> - <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
> - clock-names = "aux", "cfg_ahb", "ref", "com_aux";
> -
> - resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
> - <&gcc GCC_USB3_PHY_SEC_BCR>;
> - reset-names = "phy", "common";
> -
> - lane@88eb200 {
> - reg = <0x88eb200 0x128>,
> - <0x88eb400 0x1fc>,
> - <0x88eb800 0x218>,
> - <0x88eb600 0x70>;
> - #clock-cells = <0>;
> - #phy-cells = <0>;
> - clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
> - clock-names = "pipe0";
> - clock-output-names = "usb3_uni_phy_pipe_clk_src";
> - };
> - };
> -
> - phy@1d87000 {
> - compatible = "qcom,sdm845-qmp-ufs-phy";
> - reg = <0x1d87000 0x18c>;
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> - clock-names = "ref",
> - "ref_aux";
> - clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
> - <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
> -
> - lanes@1d87400 {
> - reg = <0x1d87400 0x108>,
> - <0x1d87600 0x1e0>,
> - <0x1d87c00 0x1dc>,
> - <0x1d87800 0x108>,
> - <0x1d87a00 0x1e0>;
> - #phy-cells = <0>;
> - };
> - };
> --
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
> of Code Aurora Forum, hosted by The Linux Foundation
>
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2020-04-29 19:06 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-04-28 14:06 [PATCH v6 0/4] Add QMP V3 USB3 PHY support for SC7180 Sandeep Maheswaram
2020-04-28 14:06 ` [PATCH v6 1/4] dt-bindings: phy: qcom,qmp: Convert QMP PHY bindings to yaml Sandeep Maheswaram
2020-04-29 19:06 ` Matthias Kaehlcke
2020-04-28 14:06 ` [PATCH v6 2/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add dt bindings for USB3 DP PHY Sandeep Maheswaram
2020-04-29 18:59 ` Matthias Kaehlcke
2020-04-28 14:06 ` [PATCH v6 3/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add support for SC7180 Sandeep Maheswaram
2020-04-28 14:06 ` [PATCH v6 4/4] phy: qcom-qmp: Add QMP V3 USB3 PHY " Sandeep Maheswaram
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).