* [PATCH v4] bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot
@ 2020-05-28 5:37 Zijun Hu
2020-05-28 8:19 ` Marcel Holtmann
0 siblings, 1 reply; 3+ messages in thread
From: Zijun Hu @ 2020-05-28 5:37 UTC (permalink / raw)
To: marcel, johan.hedberg
Cc: linux-kernel, linux-bluetooth, linux-arm-msm, bgodavar, c-hbandi,
hemantg, mka, rjliao, zijuhu
Warm reboot can not restore qca6390 controller baudrate
to default due to lack of controllable BT_EN pin or power
supply, so fails to download firmware after warm reboot.
Fixed by sending EDL_SOC_RESET VSC to reset controller
within added device shutdown implementation.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
---
drivers/bluetooth/hci_qca.c | 33 +++++++++++++++++++++++++++++++++
1 file changed, 33 insertions(+)
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index e4a6823..8e03bfe 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -1975,6 +1975,38 @@ static void qca_serdev_remove(struct serdev_device *serdev)
hci_uart_unregister_device(&qcadev->serdev_hu);
}
+static void qca_serdev_shutdown(struct device *dev)
+{
+ int ret;
+ int timeout = msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS);
+ struct serdev_device *serdev = to_serdev_device(dev);
+ struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev);
+ const u8 ibs_wake_cmd[] = { 0xFD };
+ const u8 edl_reset_soc_cmd[] = { 0x01, 0x00, 0xFC, 0x01, 0x05 };
+
+ if (qcadev->btsoc_type == QCA_QCA6390) {
+ serdev_device_write_flush(serdev);
+ ret = serdev_device_write_buf(serdev,
+ ibs_wake_cmd, sizeof(ibs_wake_cmd));
+ if (ret < 0) {
+ BT_ERR("QCA send IBS_WAKE_IND error: %d", ret);
+ return;
+ }
+ serdev_device_wait_until_sent(serdev, timeout);
+ usleep_range(8000, 10000);
+
+ serdev_device_write_flush(serdev);
+ ret = serdev_device_write_buf(serdev,
+ edl_reset_soc_cmd, sizeof(edl_reset_soc_cmd));
+ if (ret < 0) {
+ BT_ERR("QCA send EDL_RESET_REQ error: %d", ret);
+ return;
+ }
+ serdev_device_wait_until_sent(serdev, timeout);
+ usleep_range(8000, 10000);
+ }
+}
+
static int __maybe_unused qca_suspend(struct device *dev)
{
struct hci_dev *hdev = container_of(dev, struct hci_dev, dev);
@@ -2100,6 +2132,7 @@ static struct serdev_device_driver qca_serdev_driver = {
.name = "hci_uart_qca",
.of_match_table = of_match_ptr(qca_bluetooth_of_match),
.acpi_match_table = ACPI_PTR(qca_bluetooth_acpi_match),
+ .shutdown = qca_serdev_shutdown,
.pm = &qca_pm_ops,
},
};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v4] bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot
2020-05-28 5:37 [PATCH v4] bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot Zijun Hu
@ 2020-05-28 8:19 ` Marcel Holtmann
2020-05-28 9:18 ` Zijun Hu
0 siblings, 1 reply; 3+ messages in thread
From: Marcel Holtmann @ 2020-05-28 8:19 UTC (permalink / raw)
To: Zijun Hu
Cc: Johan Hedberg, linux-kernel, linux-bluetooth, linux-arm-msm,
bgodavar, c-hbandi, hemantg, mka, rjliao
Hi Zijun,
> Warm reboot can not restore qca6390 controller baudrate
> to default due to lack of controllable BT_EN pin or power
> supply, so fails to download firmware after warm reboot.
>
> Fixed by sending EDL_SOC_RESET VSC to reset controller
> within added device shutdown implementation.
>
> Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
> ---
> drivers/bluetooth/hci_qca.c | 33 +++++++++++++++++++++++++++++++++
> 1 file changed, 33 insertions(+)
>
> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> index e4a6823..8e03bfe 100644
> --- a/drivers/bluetooth/hci_qca.c
> +++ b/drivers/bluetooth/hci_qca.c
> @@ -1975,6 +1975,38 @@ static void qca_serdev_remove(struct serdev_device *serdev)
> hci_uart_unregister_device(&qcadev->serdev_hu);
> }
>
> +static void qca_serdev_shutdown(struct device *dev)
> +{
> + int ret;
> + int timeout = msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS);
> + struct serdev_device *serdev = to_serdev_device(dev);
> + struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev);
> + const u8 ibs_wake_cmd[] = { 0xFD };
> + const u8 edl_reset_soc_cmd[] = { 0x01, 0x00, 0xFC, 0x01, 0x05 };
struct hci_dev *hdev = container_of(dev, struct hci_dev, dev);
> +
> + if (qcadev->btsoc_type == QCA_QCA6390) {
> + serdev_device_write_flush(serdev);
> + ret = serdev_device_write_buf(serdev,
> + ibs_wake_cmd, sizeof(ibs_wake_cmd));
> + if (ret < 0) {
> + BT_ERR("QCA send IBS_WAKE_IND error: %d", ret);
And then use bt_dev_err here.
> + return;
> + }
> + serdev_device_wait_until_sent(serdev, timeout);
> + usleep_range(8000, 10000);
> +
> + serdev_device_write_flush(serdev);
> + ret = serdev_device_write_buf(serdev,
> + edl_reset_soc_cmd, sizeof(edl_reset_soc_cmd));
> + if (ret < 0) {
> + BT_ERR("QCA send EDL_RESET_REQ error: %d", ret);
> + return;
> + }
> + serdev_device_wait_until_sent(serdev, timeout);
> + usleep_range(8000, 10000);
> + }
> +}
> +
> static int __maybe_unused qca_suspend(struct device *dev)
> {
> struct hci_dev *hdev = container_of(dev, struct hci_dev, dev);
> @@ -2100,6 +2132,7 @@ static struct serdev_device_driver qca_serdev_driver = {
> .name = "hci_uart_qca",
> .of_match_table = of_match_ptr(qca_bluetooth_of_match),
> .acpi_match_table = ACPI_PTR(qca_bluetooth_acpi_match),
> + .shutdown = qca_serdev_shutdown,
> .pm = &qca_pm_ops,
> },
> };
Regards
Marcel
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v4] bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot
2020-05-28 8:19 ` Marcel Holtmann
@ 2020-05-28 9:18 ` Zijun Hu
0 siblings, 0 replies; 3+ messages in thread
From: Zijun Hu @ 2020-05-28 9:18 UTC (permalink / raw)
To: Marcel Holtmann
Cc: Johan Hedberg, linux-kernel, linux-bluetooth, linux-arm-msm,
bgodavar, c-hbandi, hemantg, mka, rjliao
On 5/28/2020 4:19 PM, Marcel Holtmann wrote:
> Hi Zijun,
>
>> Warm reboot can not restore qca6390 controller baudrate
>> to default due to lack of controllable BT_EN pin or power
>> supply, so fails to download firmware after warm reboot.
>>
>> Fixed by sending EDL_SOC_RESET VSC to reset controller
>> within added device shutdown implementation.
>>
>> Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
>> ---
>> drivers/bluetooth/hci_qca.c | 33 +++++++++++++++++++++++++++++++++
>> 1 file changed, 33 insertions(+)
>>
>> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
>> index e4a6823..8e03bfe 100644
>> --- a/drivers/bluetooth/hci_qca.c
>> +++ b/drivers/bluetooth/hci_qca.c
>> @@ -1975,6 +1975,38 @@ static void qca_serdev_remove(struct serdev_device *serdev)
>> hci_uart_unregister_device(&qcadev->serdev_hu);
>> }
>>
>> +static void qca_serdev_shutdown(struct device *dev)
>> +{
>> + int ret;
>> + int timeout = msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS);
>> + struct serdev_device *serdev = to_serdev_device(dev);
>> + struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev);
>> + const u8 ibs_wake_cmd[] = { 0xFD };
>> + const u8 edl_reset_soc_cmd[] = { 0x01, 0x00, 0xFC, 0x01, 0x05 };
>
> struct hci_dev *hdev = container_of(dev, struct hci_dev, dev);
> no.
this dev is serdev_device not hci_dev
>> +
>> + if (qcadev->btsoc_type == QCA_QCA6390) {
>> + serdev_device_write_flush(serdev);
>> + ret = serdev_device_write_buf(serdev,
>> + ibs_wake_cmd, sizeof(ibs_wake_cmd));
>> + if (ret < 0) {
>> + BT_ERR("QCA send IBS_WAKE_IND error: %d", ret);
>
> And then use bt_dev_err here.
as explained above about dev, bt_dev_err is not a good selection at
this serdev_device shudown operation.
>
>> + return;
>> + }
>> + serdev_device_wait_until_sent(serdev, timeout);
>> + usleep_range(8000, 10000);
>> +
>> + serdev_device_write_flush(serdev);
>> + ret = serdev_device_write_buf(serdev,
>> + edl_reset_soc_cmd, sizeof(edl_reset_soc_cmd));
>> + if (ret < 0) {
>> + BT_ERR("QCA send EDL_RESET_REQ error: %d", ret);
>> + return;
>> + }
>> + serdev_device_wait_until_sent(serdev, timeout);
>> + usleep_range(8000, 10000);
>> + }
>> +}
>> +
>> static int __maybe_unused qca_suspend(struct device *dev)
>> {
>> struct hci_dev *hdev = container_of(dev, struct hci_dev, dev);
>> @@ -2100,6 +2132,7 @@ static struct serdev_device_driver qca_serdev_driver = {
>> .name = "hci_uart_qca",
>> .of_match_table = of_match_ptr(qca_bluetooth_of_match),
>> .acpi_match_table = ACPI_PTR(qca_bluetooth_acpi_match),
>> + .shutdown = qca_serdev_shutdown,
>> .pm = &qca_pm_ops,
>> },
>> };
>
> Regards
>
> Marcel
>
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2020-05-28 9:18 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-05-28 5:37 [PATCH v4] bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot Zijun Hu
2020-05-28 8:19 ` Marcel Holtmann
2020-05-28 9:18 ` Zijun Hu
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).