[PATCH v9 1/9] scsi: ufs: Add checks before setting clk-gating states

[PATCH v9 1/9] scsi: ufs: Add checks before setting clk-gating states

[Can Guo]

Clock gating features can be turned on/off selectively which means its
state information is only important if it is enabled. This change makes
sure that we only look at state of clk-gating if it is enabled.

Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
---
 drivers/scsi/ufs/ufshcd.c | 17 ++++++++++++++---
 1 file changed, 14 insertions(+), 3 deletions(-)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 3076222..5acb38c 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -1839,6 +1839,8 @@ static void ufshcd_init_clk_gating(struct ufs_hba *hba)
 	if (!ufshcd_is_clkgating_allowed(hba))
 		return;
 
+	hba->clk_gating.state = CLKS_ON;
+
 	hba->clk_gating.delay_ms = 150;
 	INIT_DELAYED_WORK(&hba->clk_gating.gate_work, ufshcd_gate_work);
 	INIT_WORK(&hba->clk_gating.ungate_work, ufshcd_ungate_work);
@@ -2541,7 +2543,8 @@ static int ufshcd_queuecommand(struct Scsi_Host *host, struct scsi_cmnd *cmd)
 		err = SCSI_MLQUEUE_HOST_BUSY;
 		goto out;
 	}
-	WARN_ON(hba->clk_gating.state != CLKS_ON);
+	WARN_ON(ufshcd_is_clkgating_allowed(hba) &&
+		(hba->clk_gating.state != CLKS_ON));
 
 	lrbp = &hba->lrb[tag];
 
@@ -8326,8 +8329,11 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
 		/* If link is active, device ref_clk can't be switched off */
 		__ufshcd_setup_clocks(hba, false, true);
 
-	hba->clk_gating.state = CLKS_OFF;
-	trace_ufshcd_clk_gating(dev_name(hba->dev), hba->clk_gating.state);
+	if (ufshcd_is_clkgating_allowed(hba)) {
+		hba->clk_gating.state = CLKS_OFF;
+		trace_ufshcd_clk_gating(dev_name(hba->dev),
+					hba->clk_gating.state);
+	}
 
 	/* Put the host controller in low power mode if possible */
 	ufshcd_hba_vreg_set_lpm(hba);
@@ -8467,6 +8473,11 @@ static int ufshcd_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
 	if (hba->clk_scaling.is_allowed)
 		ufshcd_suspend_clkscaling(hba);
 	ufshcd_setup_clocks(hba, false);
+	if (ufshcd_is_clkgating_allowed(hba)) {
+		hba->clk_gating.state = CLKS_OFF;
+		trace_ufshcd_clk_gating(dev_name(hba->dev),
+					hba->clk_gating.state);
+	}
 out:
 	hba->pm_op_in_progress = 0;
 	if (ret)
-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

[PATCH v9 2/9] ufs: ufs-qcom: Fix race conditions caused by func ufs_qcom_testbus_config

[Can Guo]

If ufs_qcom_dump_dbg_regs() calls ufs_qcom_testbus_config() from
ufshcd_suspend/resume and/or clk gate/ungate context, pm_runtime_get_sync()
and ufshcd_hold() will cause racing problems. Fix this by removing the
unnecessary calls of pm_runtime_get_sync() and ufshcd_hold().

Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
---
 drivers/scsi/ufs/ufs-qcom.c | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/drivers/scsi/ufs/ufs-qcom.c b/drivers/scsi/ufs/ufs-qcom.c
index d0d7552..823eccf 100644
--- a/drivers/scsi/ufs/ufs-qcom.c
+++ b/drivers/scsi/ufs/ufs-qcom.c
@@ -1614,9 +1614,6 @@ int ufs_qcom_testbus_config(struct ufs_qcom_host *host)
 	 */
 	}
 	mask <<= offset;
-
-	pm_runtime_get_sync(host->hba->dev);
-	ufshcd_hold(host->hba, false);
 	ufshcd_rmwl(host->hba, TEST_BUS_SEL,
 		    (u32)host->testbus.select_major << 19,
 		    REG_UFS_CFG1);
@@ -1629,8 +1626,6 @@ int ufs_qcom_testbus_config(struct ufs_qcom_host *host)
 	 * committed before returning.
 	 */
 	mb();
-	ufshcd_release(host->hba);
-	pm_runtime_put_sync(host->hba->dev);
 
 	return 0;
 }
-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

[PATCH v9 3/9] scsi: ufs-qcom: Remove testbus dump in ufs_qcom_dump_dbg_regs

[Can Guo]

Dumping testbus registers is heavy enough to cause stability issues
sometime, just remove them as of now.

Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
---
 drivers/scsi/ufs/ufs-qcom.c | 32 --------------------------------
 1 file changed, 32 deletions(-)

diff --git a/drivers/scsi/ufs/ufs-qcom.c b/drivers/scsi/ufs/ufs-qcom.c
index 823eccf..6b75338 100644
--- a/drivers/scsi/ufs/ufs-qcom.c
+++ b/drivers/scsi/ufs/ufs-qcom.c
@@ -1630,44 +1630,12 @@ int ufs_qcom_testbus_config(struct ufs_qcom_host *host)
 	return 0;
 }
 
-static void ufs_qcom_testbus_read(struct ufs_hba *hba)
-{
-	ufshcd_dump_regs(hba, UFS_TEST_BUS, 4, "UFS_TEST_BUS ");
-}
-
-static void ufs_qcom_print_unipro_testbus(struct ufs_hba *hba)
-{
-	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
-	u32 *testbus = NULL;
-	int i, nminor = 256, testbus_len = nminor * sizeof(u32);
-
-	testbus = kmalloc(testbus_len, GFP_KERNEL);
-	if (!testbus)
-		return;
-
-	host->testbus.select_major = TSTBUS_UNIPRO;
-	for (i = 0; i < nminor; i++) {
-		host->testbus.select_minor = i;
-		ufs_qcom_testbus_config(host);
-		testbus[i] = ufshcd_readl(hba, UFS_TEST_BUS);
-	}
-	print_hex_dump(KERN_ERR, "UNIPRO_TEST_BUS ", DUMP_PREFIX_OFFSET,
-			16, 4, testbus, testbus_len, false);
-	kfree(testbus);
-}
-
 static void ufs_qcom_dump_dbg_regs(struct ufs_hba *hba)
 {
 	ufshcd_dump_regs(hba, REG_UFS_SYS1CLK_1US, 16 * 4,
 			 "HCI Vendor Specific Registers ");
 
-	/* sleep a bit intermittently as we are dumping too much data */
 	ufs_qcom_print_hw_debug_reg_all(hba, NULL, ufs_qcom_dump_regs_wrapper);
-	udelay(1000);
-	ufs_qcom_testbus_read(hba);
-	udelay(1000);
-	ufs_qcom_print_unipro_testbus(hba);
-	udelay(1000);
 }
 
 /**
-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

[PATCH v9 4/9] scsi: ufs: Add some debug infos to ufshcd_print_host_state

[Can Guo]

The infos of the last interrupt status and its timestamp are very helpful
when debug system stability issues, e.g. IRQ starvation, so add them to
ufshcd_print_host_state. Meanwhile, UFS device infos like model name and
its FW version also come in handy during debug. In addition, this change
makes cleanup to some prints in ufshcd_print_host_regs as similar prints
are already available in ufshcd_print_host_state.

Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
---
 drivers/scsi/ufs/ufshcd.c | 31 ++++++++++++++++++-------------
 drivers/scsi/ufs/ufshcd.h |  5 +++++
 2 files changed, 23 insertions(+), 13 deletions(-)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 5acb38c..71c650f 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -411,15 +411,6 @@ static void ufshcd_print_err_hist(struct ufs_hba *hba,
 static void ufshcd_print_host_regs(struct ufs_hba *hba)
 {
 	ufshcd_dump_regs(hba, 0, UFSHCI_REG_SPACE_SIZE, "host_regs: ");
-	dev_err(hba->dev, "hba->ufs_version = 0x%x, hba->capabilities = 0x%x\n",
-		hba->ufs_version, hba->capabilities);
-	dev_err(hba->dev,
-		"hba->outstanding_reqs = 0x%x, hba->outstanding_tasks = 0x%x\n",
-		(u32)hba->outstanding_reqs, (u32)hba->outstanding_tasks);
-	dev_err(hba->dev,
-		"last_hibern8_exit_tstamp at %lld us, hibern8_exit_cnt = %d\n",
-		ktime_to_us(hba->ufs_stats.last_hibern8_exit_tstamp),
-		hba->ufs_stats.hibern8_exit_cnt);
 
 	ufshcd_print_err_hist(hba, &hba->ufs_stats.pa_err, "pa_err");
 	ufshcd_print_err_hist(hba, &hba->ufs_stats.dl_err, "dl_err");
@@ -438,8 +429,6 @@ static void ufshcd_print_host_regs(struct ufs_hba *hba)
 	ufshcd_print_err_hist(hba, &hba->ufs_stats.host_reset, "host_reset");
 	ufshcd_print_err_hist(hba, &hba->ufs_stats.task_abort, "task_abort");
 
-	ufshcd_print_clk_freqs(hba);
-
 	ufshcd_vops_dbg_register_dump(hba);
 }
 
@@ -499,6 +488,8 @@ static void ufshcd_print_tmrs(struct ufs_hba *hba, unsigned long bitmap)
 
 static void ufshcd_print_host_state(struct ufs_hba *hba)
 {
+	struct scsi_device *sdev_ufs = hba->sdev_ufs_device;
+
 	dev_err(hba->dev, "UFS Host state=%d\n", hba->ufshcd_state);
 	dev_err(hba->dev, "outstanding reqs=0x%lx tasks=0x%lx\n",
 		hba->outstanding_reqs, hba->outstanding_tasks);
@@ -511,12 +502,24 @@ static void ufshcd_print_host_state(struct ufs_hba *hba)
 	dev_err(hba->dev, "Auto BKOPS=%d, Host self-block=%d\n",
 		hba->auto_bkops_enabled, hba->host->host_self_blocked);
 	dev_err(hba->dev, "Clk gate=%d\n", hba->clk_gating.state);
+	dev_err(hba->dev,
+		"last_hibern8_exit_tstamp at %lld us, hibern8_exit_cnt=%d\n",
+		ktime_to_us(hba->ufs_stats.last_hibern8_exit_tstamp),
+		hba->ufs_stats.hibern8_exit_cnt);
+	dev_err(hba->dev, "last intr at %lld us, last intr status=0x%x\n",
+		ktime_to_us(hba->ufs_stats.last_intr_ts),
+		hba->ufs_stats.last_intr_status);
 	dev_err(hba->dev, "error handling flags=0x%x, req. abort count=%d\n",
 		hba->eh_flags, hba->req_abort_count);
-	dev_err(hba->dev, "Host capabilities=0x%x, caps=0x%x\n",
-		hba->capabilities, hba->caps);
+	dev_err(hba->dev, "hba->ufs_version=0x%x, Host capabilities=0x%x, caps=0x%x\n",
+		hba->ufs_version, hba->capabilities, hba->caps);
 	dev_err(hba->dev, "quirks=0x%x, dev. quirks=0x%x\n", hba->quirks,
 		hba->dev_quirks);
+	if (sdev_ufs)
+		dev_err(hba->dev, "UFS dev info: %.8s %.16s rev %.4s\n",
+			sdev_ufs->vendor, sdev_ufs->model, sdev_ufs->rev);
+
+	ufshcd_print_clk_freqs(hba);
 }
 
 /**
@@ -5951,6 +5954,8 @@ static irqreturn_t ufshcd_intr(int irq, void *__hba)
 
 	spin_lock(hba->host->host_lock);
 	intr_status = ufshcd_readl(hba, REG_INTERRUPT_STATUS);
+	hba->ufs_stats.last_intr_status = intr_status;
+	hba->ufs_stats.last_intr_ts = ktime_get();
 
 	/*
 	 * There could be max of hba->nutrs reqs in flight and in worst case
diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
index b2ef18f..b7f54af 100644
--- a/drivers/scsi/ufs/ufshcd.h
+++ b/drivers/scsi/ufs/ufshcd.h
@@ -409,6 +409,8 @@ struct ufs_err_reg_hist {
 
 /**
  * struct ufs_stats - keeps usage/err statistics
+ * @last_intr_status: record the last interrupt status.
+ * @last_intr_ts: record the last interrupt timestamp.
  * @hibern8_exit_cnt: Counter to keep track of number of exits,
  *		reset this after link-startup.
  * @last_hibern8_exit_tstamp: Set time after the hibern8 exit.
@@ -428,6 +430,9 @@ struct ufs_err_reg_hist {
  * @tsk_abort: tracks task abort events
  */
 struct ufs_stats {
+	u32 last_intr_status;
+	ktime_t last_intr_ts;
+
 	u32 hibern8_exit_cnt;
 	ktime_t last_hibern8_exit_tstamp;
 
-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

[PATCH v9 5/9] scsi: ufs: Fix concurrency of error handler and other error recovery paths

[Can Guo]

Error recovery can be invoked from multiple paths, including hibern8
enter/exit (from ufshcd_link_recovery), ufshcd_eh_host_reset_handler and
eh_work scheduled from IRQ context. Ultimately, these paths are trying to
invoke ufshcd_reset_and_restore, in either sync or async manner.

Having both sync and async manners at the same time has some problems

- If link recovery happens during ungate work, ufshcd_hold() would be
  called recursively. Although commit 53c12d0ef6fcb
  ("scsi: ufs: fix error recovery after the hibern8 exit failure") [1]
  fixed a deadlock due to recursive calls of ufshcd_hold() by adding a
  check of eh_in_progress into ufshcd_hold, this check allows eh_work to
  run in parallel while link recovery is running.

- Similar concurrency can also happen when error recovery is invoked from
  ufshcd_eh_host_reset_handler and ufshcd_link_recovery.

- Concurrency can even happen between eh_works. eh_work, currently queued
  on system_wq, is allowed to have multiple instances running in parallel,
  but we don't have proper protection for that.

If any of above concurrency happens, error recovery would fail and lead
ufs device and host into bad states. To fix the concurrency problem, this
change queues eh_work on a single threaded workqueue and remove link
recovery calls from hibern8 enter/exit path. Meanwhile, make use of eh_work
in eh_host_reset_handler instead of calling ufshcd_reset_and_restore. This
unifies UFS error recovery mechanism.

In addition, according to the UFSHCI JEDEC spec, hibern8 enter/exit error
occurs when the link is broken. This essentially applies to any power mode
change operations (since they all use PACP_PWR cmds in UniPro layer). So,
in this change, if a power mode change operation (including AH8 enter/exit)
fails, mark link state as UIC_LINK_BROKEN_STATE and schedule the eh_work.
In this case, error handler needs to do a full reset and restore to recover
the link back to active. Before the link state is recovered to active,
ufshcd_uic_pwr_ctrl simply returns -ENOLINK to avoid more errors.

Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
---
 drivers/scsi/ufs/ufs-sysfs.c |   1 +
 drivers/scsi/ufs/ufshcd.c    | 268 ++++++++++++++++++++++---------------------
 drivers/scsi/ufs/ufshcd.h    |   9 ++
 3 files changed, 150 insertions(+), 128 deletions(-)

diff --git a/drivers/scsi/ufs/ufs-sysfs.c b/drivers/scsi/ufs/ufs-sysfs.c
index 2d71d23..02d379f00 100644
--- a/drivers/scsi/ufs/ufs-sysfs.c
+++ b/drivers/scsi/ufs/ufs-sysfs.c
@@ -16,6 +16,7 @@ static const char *ufschd_uic_link_state_to_string(
 	case UIC_LINK_OFF_STATE:	return "OFF";
 	case UIC_LINK_ACTIVE_STATE:	return "ACTIVE";
 	case UIC_LINK_HIBERN8_STATE:	return "HIBERN8";
+	case UIC_LINK_BROKEN_STATE:	return "BROKEN";
 	default:			return "UNKNOWN";
 	}
 }
diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 71c650f..2604016 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -228,6 +228,7 @@ static int ufshcd_scale_clks(struct ufs_hba *hba, bool scale_up);
 static irqreturn_t ufshcd_intr(int irq, void *__hba);
 static int ufshcd_change_power_mode(struct ufs_hba *hba,
 			     struct ufs_pa_layer_attr *pwr_mode);
+static void ufshcd_schedule_eh_work(struct ufs_hba *hba);
 static int ufshcd_wb_buf_flush_enable(struct ufs_hba *hba);
 static int ufshcd_wb_buf_flush_disable(struct ufs_hba *hba);
 static int ufshcd_wb_ctrl(struct ufs_hba *hba, bool enable);
@@ -1571,11 +1572,6 @@ int ufshcd_hold(struct ufs_hba *hba, bool async)
 	spin_lock_irqsave(hba->host->host_lock, flags);
 	hba->clk_gating.active_reqs++;
 
-	if (ufshcd_eh_in_progress(hba)) {
-		spin_unlock_irqrestore(hba->host->host_lock, flags);
-		return 0;
-	}
-
 start:
 	switch (hba->clk_gating.state) {
 	case CLKS_ON:
@@ -1653,6 +1649,7 @@ static void ufshcd_gate_work(struct work_struct *work)
 	struct ufs_hba *hba = container_of(work, struct ufs_hba,
 			clk_gating.gate_work.work);
 	unsigned long flags;
+	int ret;
 
 	spin_lock_irqsave(hba->host->host_lock, flags);
 	/*
@@ -1679,8 +1676,11 @@ static void ufshcd_gate_work(struct work_struct *work)
 
 	/* put the link into hibern8 mode before turning off clocks */
 	if (ufshcd_can_hibern8_during_gating(hba)) {
-		if (ufshcd_uic_hibern8_enter(hba)) {
+		ret = ufshcd_uic_hibern8_enter(hba);
+		if (ret) {
 			hba->clk_gating.state = CLKS_ON;
+			dev_err(hba->dev, "%s: hibern8 enter failed %d\n",
+					__func__, ret);
 			trace_ufshcd_clk_gating(dev_name(hba->dev),
 						hba->clk_gating.state);
 			goto out;
@@ -1725,11 +1725,10 @@ static void __ufshcd_release(struct ufs_hba *hba)
 
 	hba->clk_gating.active_reqs--;
 
-	if (hba->clk_gating.active_reqs || hba->clk_gating.is_suspended
-		|| hba->ufshcd_state != UFSHCD_STATE_OPERATIONAL
-		|| ufshcd_any_tag_in_use(hba) || hba->outstanding_tasks
-		|| hba->active_uic_cmd || hba->uic_async_done
-		|| ufshcd_eh_in_progress(hba))
+	if (hba->clk_gating.active_reqs || hba->clk_gating.is_suspended ||
+	    hba->ufshcd_state != UFSHCD_STATE_OPERATIONAL ||
+	    ufshcd_any_tag_in_use(hba) || hba->outstanding_tasks ||
+	    hba->active_uic_cmd || hba->uic_async_done)
 		return;
 
 	hba->clk_gating.state = REQ_CLKS_OFF;
@@ -3750,6 +3749,10 @@ static int ufshcd_uic_pwr_ctrl(struct ufs_hba *hba, struct uic_command *cmd)
 	ufshcd_add_delay_before_dme_cmd(hba);
 
 	spin_lock_irqsave(hba->host->host_lock, flags);
+	if (ufshcd_is_link_broken(hba)) {
+		ret = -ENOLINK;
+		goto out_unlock;
+	}
 	hba->uic_async_done = &uic_async_done;
 	if (ufshcd_readl(hba, REG_INTERRUPT_ENABLE) & UIC_COMMAND_COMPL) {
 		ufshcd_disable_intr(hba, UIC_COMMAND_COMPL);
@@ -3797,6 +3800,11 @@ static int ufshcd_uic_pwr_ctrl(struct ufs_hba *hba, struct uic_command *cmd)
 	hba->uic_async_done = NULL;
 	if (reenable_intr)
 		ufshcd_enable_intr(hba, UIC_COMMAND_COMPL);
+	if (ret) {
+		ufshcd_set_link_broken(hba);
+		ufshcd_schedule_eh_work(hba);
+	}
+out_unlock:
 	spin_unlock_irqrestore(hba->host->host_lock, flags);
 	mutex_unlock(&hba->uic_cmd_mutex);
 
@@ -3866,7 +3874,7 @@ int ufshcd_link_recovery(struct ufs_hba *hba)
 }
 EXPORT_SYMBOL_GPL(ufshcd_link_recovery);
 
-static int __ufshcd_uic_hibern8_enter(struct ufs_hba *hba)
+static int ufshcd_uic_hibern8_enter(struct ufs_hba *hba)
 {
 	int ret;
 	struct uic_command uic_cmd = {0};
@@ -3879,45 +3887,16 @@ static int __ufshcd_uic_hibern8_enter(struct ufs_hba *hba)
 	trace_ufshcd_profile_hibern8(dev_name(hba->dev), "enter",
 			     ktime_to_us(ktime_sub(ktime_get(), start)), ret);
 
-	if (ret) {
-		int err;
-
+	if (ret)
 		dev_err(hba->dev, "%s: hibern8 enter failed. ret = %d\n",
 			__func__, ret);
-
-		/*
-		 * If link recovery fails then return error code returned from
-		 * ufshcd_link_recovery().
-		 * If link recovery succeeds then return -EAGAIN to attempt
-		 * hibern8 enter retry again.
-		 */
-		err = ufshcd_link_recovery(hba);
-		if (err) {
-			dev_err(hba->dev, "%s: link recovery failed", __func__);
-			ret = err;
-		} else {
-			ret = -EAGAIN;
-		}
-	} else
+	else
 		ufshcd_vops_hibern8_notify(hba, UIC_CMD_DME_HIBER_ENTER,
 								POST_CHANGE);
 
 	return ret;
 }
 
-static int ufshcd_uic_hibern8_enter(struct ufs_hba *hba)
-{
-	int ret = 0, retries;
-
-	for (retries = UIC_HIBERN8_ENTER_RETRIES; retries > 0; retries--) {
-		ret = __ufshcd_uic_hibern8_enter(hba);
-		if (!ret)
-			goto out;
-	}
-out:
-	return ret;
-}
-
 int ufshcd_uic_hibern8_exit(struct ufs_hba *hba)
 {
 	struct uic_command uic_cmd = {0};
@@ -3934,7 +3913,6 @@ int ufshcd_uic_hibern8_exit(struct ufs_hba *hba)
 	if (ret) {
 		dev_err(hba->dev, "%s: hibern8 exit failed. ret = %d\n",
 			__func__, ret);
-		ret = ufshcd_link_recovery(hba);
 	} else {
 		ufshcd_vops_hibern8_notify(hba, UIC_CMD_DME_HIBER_EXIT,
 								POST_CHANGE);
@@ -5557,6 +5535,24 @@ static bool ufshcd_quirk_dl_nac_errors(struct ufs_hba *hba)
 	return err_handling;
 }
 
+/* host lock must be held before calling this func */
+static inline bool ufshcd_is_saved_err_fatal(struct ufs_hba *hba)
+{
+	return (hba->saved_uic_err & UFSHCD_UIC_DL_PA_INIT_ERROR) ||
+	       (hba->saved_err & (INT_FATAL_ERRORS | UFSHCD_UIC_HIBERN8_MASK));
+}
+
+/* host lock must be held before calling this func */
+static inline void ufshcd_schedule_eh_work(struct ufs_hba *hba)
+{
+	/* handle fatal errors only when link is not in error state */
+	if (hba->ufshcd_state != UFSHCD_STATE_ERROR) {
+		hba->ufshcd_state = UFSHCD_STATE_EH_SCHEDULED;
+		if (queue_work(hba->eh_wq, &hba->eh_work))
+			ufshcd_scsi_block_requests(hba);
+	}
+}
+
 /**
  * ufshcd_err_handler - handle UFS errors that require s/w attention
  * @work: pointer to work structure
@@ -5573,15 +5569,23 @@ static void ufshcd_err_handler(struct work_struct *work)
 
 	hba = container_of(work, struct ufs_hba, eh_work);
 
+	spin_lock_irqsave(hba->host->host_lock, flags);
+	if (hba->ufshcd_state == UFSHCD_STATE_ERROR ||
+	    (!(hba->saved_err || hba->saved_uic_err || hba->force_reset ||
+		ufshcd_is_link_broken(hba)))) {
+		if (hba->ufshcd_state != UFSHCD_STATE_ERROR)
+			hba->ufshcd_state = UFSHCD_STATE_OPERATIONAL;
+		spin_unlock_irqrestore(hba->host->host_lock, flags);
+		ufshcd_scsi_unblock_requests(hba);
+		return;
+	}
+	ufshcd_set_eh_in_progress(hba);
+	spin_unlock_irqrestore(hba->host->host_lock, flags);
 	pm_runtime_get_sync(hba->dev);
 	ufshcd_hold(hba, false);
 
 	spin_lock_irqsave(hba->host->host_lock, flags);
-	if (hba->ufshcd_state == UFSHCD_STATE_RESET)
-		goto out;
-
 	hba->ufshcd_state = UFSHCD_STATE_RESET;
-	ufshcd_set_eh_in_progress(hba);
 
 	/* Complete requests that have door-bell cleared by h/w */
 	ufshcd_complete_requests(hba);
@@ -5593,15 +5597,15 @@ static void ufshcd_err_handler(struct work_struct *work)
 		/* release the lock as ufshcd_quirk_dl_nac_errors() may sleep */
 		ret = ufshcd_quirk_dl_nac_errors(hba);
 		spin_lock_irqsave(hba->host->host_lock, flags);
-		if (!ret)
+		if (!ret && !hba->force_reset && ufshcd_is_link_active(hba))
 			goto skip_err_handling;
 	}
-	if ((hba->saved_err & INT_FATAL_ERRORS) ||
-	    (hba->saved_err & UFSHCD_UIC_HIBERN8_MASK) ||
+
+	if (hba->force_reset || ufshcd_is_link_broken(hba) ||
+	    ufshcd_is_saved_err_fatal(hba) ||
 	    ((hba->saved_err & UIC_ERROR) &&
-	    (hba->saved_uic_err & (UFSHCD_UIC_DL_PA_INIT_ERROR |
-				   UFSHCD_UIC_DL_NAC_RECEIVED_ERROR |
-				   UFSHCD_UIC_DL_TCx_REPLAY_ERROR))))
+	     (hba->saved_uic_err & (UFSHCD_UIC_DL_NAC_RECEIVED_ERROR |
+				    UFSHCD_UIC_DL_TCx_REPLAY_ERROR))))
 		needs_reset = true;
 
 	/*
@@ -5655,34 +5659,25 @@ static void ufshcd_err_handler(struct work_struct *work)
 			__ufshcd_transfer_req_compl(hba,
 						    (1UL << (hba->nutrs - 1)));
 
+		hba->force_reset = false;
 		spin_unlock_irqrestore(hba->host->host_lock, flags);
 		err = ufshcd_reset_and_restore(hba);
 		spin_lock_irqsave(hba->host->host_lock, flags);
-		if (err) {
-			dev_err(hba->dev, "%s: reset and restore failed\n",
-					__func__);
-			hba->ufshcd_state = UFSHCD_STATE_ERROR;
-		}
-		/*
-		 * Inform scsi mid-layer that we did reset and allow to handle
-		 * Unit Attention properly.
-		 */
-		scsi_report_bus_reset(hba->host, 0);
-		hba->saved_err = 0;
-		hba->saved_uic_err = 0;
+		if (err)
+			dev_err(hba->dev, "%s: reset and restore failed with err %d\n",
+					__func__, err);
 	}
 
 skip_err_handling:
 	if (!needs_reset) {
-		hba->ufshcd_state = UFSHCD_STATE_OPERATIONAL;
+		if (hba->ufshcd_state == UFSHCD_STATE_RESET)
+			hba->ufshcd_state = UFSHCD_STATE_OPERATIONAL;
 		if (hba->saved_err || hba->saved_uic_err)
 			dev_err_ratelimited(hba->dev, "%s: exit: saved_err 0x%x saved_uic_err 0x%x",
 			    __func__, hba->saved_err, hba->saved_uic_err);
 	}
 
 	ufshcd_clear_eh_in_progress(hba);
-
-out:
 	spin_unlock_irqrestore(hba->host->host_lock, flags);
 	ufshcd_scsi_unblock_requests(hba);
 	ufshcd_release(hba);
@@ -5816,6 +5811,7 @@ static irqreturn_t ufshcd_check_errors(struct ufs_hba *hba)
 			hba->errors, ufshcd_get_upmcrs(hba));
 		ufshcd_update_reg_hist(&hba->ufs_stats.auto_hibern8_err,
 				       hba->errors);
+		ufshcd_set_link_broken(hba);
 		queue_eh_work = true;
 	}
 
@@ -5827,30 +5823,22 @@ static irqreturn_t ufshcd_check_errors(struct ufs_hba *hba)
 		hba->saved_err |= hba->errors;
 		hba->saved_uic_err |= hba->uic_error;
 
-		/* handle fatal errors only when link is functional */
-		if (hba->ufshcd_state == UFSHCD_STATE_OPERATIONAL) {
-			/* block commands from scsi mid-layer */
-			ufshcd_scsi_block_requests(hba);
-
-			hba->ufshcd_state = UFSHCD_STATE_EH_SCHEDULED;
+		/* dump controller state before resetting */
+		if (hba->saved_err & (INT_FATAL_ERRORS | UIC_ERROR)) {
+			bool pr_prdt = !!(hba->saved_err &
+					SYSTEM_BUS_FATAL_ERROR);
 
-			/* dump controller state before resetting */
-			if (hba->saved_err & (INT_FATAL_ERRORS | UIC_ERROR)) {
-				bool pr_prdt = !!(hba->saved_err &
-						SYSTEM_BUS_FATAL_ERROR);
-
-				dev_err(hba->dev, "%s: saved_err 0x%x saved_uic_err 0x%x\n",
+			dev_err(hba->dev, "%s: saved_err 0x%x saved_uic_err 0x%x\n",
 					__func__, hba->saved_err,
 					hba->saved_uic_err);
 
-				ufshcd_print_host_regs(hba);
-				ufshcd_print_pwr_info(hba);
-				ufshcd_print_tmrs(hba, hba->outstanding_tasks);
-				ufshcd_print_trs(hba, hba->outstanding_reqs,
-							pr_prdt);
-			}
-			schedule_work(&hba->eh_work);
+			ufshcd_print_host_regs(hba);
+			ufshcd_print_pwr_info(hba);
+			ufshcd_print_tmrs(hba, hba->outstanding_tasks);
+			ufshcd_print_trs(hba, hba->outstanding_reqs,
+					pr_prdt);
 		}
+		ufshcd_schedule_eh_work(hba);
 		retval |= IRQ_HANDLED;
 	}
 	/*
@@ -6595,8 +6583,6 @@ static int ufshcd_host_reset_and_restore(struct ufs_hba *hba)
 	/* Establish the link again and restore the device */
 	err = ufshcd_probe_hba(hba, false);
 
-	if (!err && (hba->ufshcd_state != UFSHCD_STATE_OPERATIONAL))
-		err = -EIO;
 out:
 	if (err)
 		dev_err(hba->dev, "%s: Host init failed %d\n", __func__, err);
@@ -6615,9 +6601,23 @@ static int ufshcd_host_reset_and_restore(struct ufs_hba *hba)
  */
 static int ufshcd_reset_and_restore(struct ufs_hba *hba)
 {
+	u32 saved_err;
+	u32 saved_uic_err;
 	int err = 0;
+	unsigned long flags;
 	int retries = MAX_HOST_RESET_RETRIES;
 
+	/*
+	 * This is a fresh start, cache and clear saved error first,
+	 * in case new error generated during reset and restore.
+	 */
+	spin_lock_irqsave(hba->host->host_lock, flags);
+	saved_err = hba->saved_err;
+	saved_uic_err = hba->saved_uic_err;
+	hba->saved_err = 0;
+	hba->saved_uic_err = 0;
+	spin_unlock_irqrestore(hba->host->host_lock, flags);
+
 	do {
 		/* Reset the attached device */
 		ufshcd_vops_device_reset(hba);
@@ -6625,6 +6625,18 @@ static int ufshcd_reset_and_restore(struct ufs_hba *hba)
 		err = ufshcd_host_reset_and_restore(hba);
 	} while (err && --retries);
 
+	spin_lock_irqsave(hba->host->host_lock, flags);
+	/*
+	 * Inform scsi mid-layer that we did reset and allow to handle
+	 * Unit Attention properly.
+	 */
+	scsi_report_bus_reset(hba->host, 0);
+	if (err) {
+		hba->saved_err |= saved_err;
+		hba->saved_uic_err |= saved_uic_err;
+	}
+	spin_unlock_irqrestore(hba->host->host_lock, flags);
+
 	return err;
 }
 
@@ -6636,48 +6648,25 @@ static int ufshcd_reset_and_restore(struct ufs_hba *hba)
  */
 static int ufshcd_eh_host_reset_handler(struct scsi_cmnd *cmd)
 {
-	int err;
+	int err = SUCCESS;
 	unsigned long flags;
 	struct ufs_hba *hba;
 
 	hba = shost_priv(cmd->device->host);
 
-	ufshcd_hold(hba, false);
-	/*
-	 * Check if there is any race with fatal error handling.
-	 * If so, wait for it to complete. Even though fatal error
-	 * handling does reset and restore in some cases, don't assume
-	 * anything out of it. We are just avoiding race here.
-	 */
-	do {
-		spin_lock_irqsave(hba->host->host_lock, flags);
-		if (!(work_pending(&hba->eh_work) ||
-			    hba->ufshcd_state == UFSHCD_STATE_RESET ||
-			    hba->ufshcd_state == UFSHCD_STATE_EH_SCHEDULED))
-			break;
-		spin_unlock_irqrestore(hba->host->host_lock, flags);
-		dev_dbg(hba->dev, "%s: reset in progress\n", __func__);
-		flush_work(&hba->eh_work);
-	} while (1);
-
-	hba->ufshcd_state = UFSHCD_STATE_RESET;
-	ufshcd_set_eh_in_progress(hba);
+	spin_lock_irqsave(hba->host->host_lock, flags);
+	hba->force_reset = true;
+	ufshcd_schedule_eh_work(hba);
+	dev_err(hba->dev, "%s: reset in progress - 1\n", __func__);
 	spin_unlock_irqrestore(hba->host->host_lock, flags);
 
-	err = ufshcd_reset_and_restore(hba);
+	flush_work(&hba->eh_work);
 
 	spin_lock_irqsave(hba->host->host_lock, flags);
-	if (!err) {
-		err = SUCCESS;
-		hba->ufshcd_state = UFSHCD_STATE_OPERATIONAL;
-	} else {
+	if (hba->ufshcd_state == UFSHCD_STATE_ERROR)
 		err = FAILED;
-		hba->ufshcd_state = UFSHCD_STATE_ERROR;
-	}
-	ufshcd_clear_eh_in_progress(hba);
 	spin_unlock_irqrestore(hba->host->host_lock, flags);
 
-	ufshcd_release(hba);
 	return err;
 }
 
@@ -7398,6 +7387,7 @@ static int ufshcd_add_lus(struct ufs_hba *hba)
 static int ufshcd_probe_hba(struct ufs_hba *hba, bool async)
 {
 	int ret;
+	unsigned long flags;
 	ktime_t start = ktime_get();
 
 	ret = ufshcd_link_startup(hba);
@@ -7462,14 +7452,17 @@ static int ufshcd_probe_hba(struct ufs_hba *hba, bool async)
 	 */
 	ufshcd_set_active_icc_lvl(hba);
 
-	/* set the state as operational after switching to desired gear */
-	hba->ufshcd_state = UFSHCD_STATE_OPERATIONAL;
-
 	ufshcd_wb_config(hba);
 	/* Enable Auto-Hibernate if configured */
 	ufshcd_auto_hibern8_enable(hba);
 
 out:
+	spin_lock_irqsave(hba->host->host_lock, flags);
+	if (ret)
+		hba->ufshcd_state = UFSHCD_STATE_ERROR;
+	else if (hba->ufshcd_state == UFSHCD_STATE_RESET)
+		hba->ufshcd_state = UFSHCD_STATE_OPERATIONAL;
+	spin_unlock_irqrestore(hba->host->host_lock, flags);
 
 	trace_ufshcd_init(dev_name(hba->dev), ret,
 		ktime_to_us(ktime_sub(ktime_get(), start)),
@@ -8076,10 +8069,13 @@ static int ufshcd_link_state_transition(struct ufs_hba *hba,
 
 	if (req_link_state == UIC_LINK_HIBERN8_STATE) {
 		ret = ufshcd_uic_hibern8_enter(hba);
-		if (!ret)
+		if (!ret) {
 			ufshcd_set_link_hibern8(hba);
-		else
+		} else {
+			dev_err(hba->dev, "%s: hibern8 enter failed %d\n",
+					__func__, ret);
 			goto out;
+		}
 	}
 	/*
 	 * If autobkops is enabled, link can't be turned off because
@@ -8095,8 +8091,11 @@ static int ufshcd_link_state_transition(struct ufs_hba *hba,
 		 * unipro. But putting the link in hibern8 is much faster.
 		 */
 		ret = ufshcd_uic_hibern8_enter(hba);
-		if (ret)
+		if (ret) {
+			dev_err(hba->dev, "%s: hibern8 enter failed %d\n",
+					__func__, ret);
 			goto out;
+		}
 		/*
 		 * Change controller state to "reset state" which
 		 * should also put the link in off/reset state
@@ -8416,10 +8415,13 @@ static int ufshcd_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
 
 	if (ufshcd_is_link_hibern8(hba)) {
 		ret = ufshcd_uic_hibern8_exit(hba);
-		if (!ret)
+		if (!ret) {
 			ufshcd_set_link_active(hba);
-		else
+		} else {
+			dev_err(hba->dev, "%s: hibern8 exit failed %d\n",
+					__func__, ret);
 			goto vendor_suspend;
+		}
 	} else if (ufshcd_is_link_off(hba)) {
 		/*
 		 * A full initialization of the host and the device is
@@ -8793,6 +8795,7 @@ int ufshcd_init(struct ufs_hba *hba, void __iomem *mmio_base, unsigned int irq)
 	int err;
 	struct Scsi_Host *host = hba->host;
 	struct device *dev = hba->dev;
+	char eh_wq_name[sizeof("ufs_eh_wq_00")];
 
 	if (!mmio_base) {
 		dev_err(hba->dev,
@@ -8854,6 +8857,15 @@ int ufshcd_init(struct ufs_hba *hba, void __iomem *mmio_base, unsigned int irq)
 	hba->max_pwr_info.is_valid = false;
 
 	/* Initialize work queues */
+	snprintf(eh_wq_name, sizeof(eh_wq_name), "ufs_eh_wq_%d",
+		 hba->host->host_no);
+	hba->eh_wq = create_singlethread_workqueue(eh_wq_name);
+	if (!hba->eh_wq) {
+		dev_err(hba->dev, "%s: failed to create eh workqueue\n",
+				__func__);
+		err = -ENOMEM;
+		goto out_disable;
+	}
 	INIT_WORK(&hba->eh_work, ufshcd_err_handler);
 	INIT_WORK(&hba->eeh_work, ufshcd_exception_event_handler);
 
diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
index b7f54af..618b253 100644
--- a/drivers/scsi/ufs/ufshcd.h
+++ b/drivers/scsi/ufs/ufshcd.h
@@ -90,6 +90,7 @@ enum uic_link_state {
 	UIC_LINK_OFF_STATE	= 0, /* Link powered down or disabled */
 	UIC_LINK_ACTIVE_STATE	= 1, /* Link is in Fast/Slow/Sleep state */
 	UIC_LINK_HIBERN8_STATE	= 2, /* Link is in Hibernate state */
+	UIC_LINK_BROKEN_STATE	= 3, /* Link is in broken state */
 };
 
 #define ufshcd_is_link_off(hba) ((hba)->uic_link_state == UIC_LINK_OFF_STATE)
@@ -97,11 +98,15 @@ enum uic_link_state {
 				    UIC_LINK_ACTIVE_STATE)
 #define ufshcd_is_link_hibern8(hba) ((hba)->uic_link_state == \
 				    UIC_LINK_HIBERN8_STATE)
+#define ufshcd_is_link_broken(hba) ((hba)->uic_link_state == \
+				   UIC_LINK_BROKEN_STATE)
 #define ufshcd_set_link_off(hba) ((hba)->uic_link_state = UIC_LINK_OFF_STATE)
 #define ufshcd_set_link_active(hba) ((hba)->uic_link_state = \
 				    UIC_LINK_ACTIVE_STATE)
 #define ufshcd_set_link_hibern8(hba) ((hba)->uic_link_state = \
 				    UIC_LINK_HIBERN8_STATE)
+#define ufshcd_set_link_broken(hba) ((hba)->uic_link_state = \
+				    UIC_LINK_BROKEN_STATE)
 
 #define ufshcd_set_ufs_dev_active(h) \
 	((h)->curr_dev_pwr_mode = UFS_ACTIVE_PWR_MODE)
@@ -616,12 +621,14 @@ struct ufs_hba_variant_params {
  * @intr_mask: Interrupt Mask Bits
  * @ee_ctrl_mask: Exception event control mask
  * @is_powered: flag to check if HBA is powered
+ * @eh_wq: Workqueue that eh_work works on
  * @eh_work: Worker to handle UFS errors that require s/w attention
  * @eeh_work: Worker to handle exception events
  * @errors: HBA errors
  * @uic_error: UFS interconnect layer error status
  * @saved_err: sticky error mask
  * @saved_uic_err: sticky UIC error mask
+ * @force_reset: flag to force eh_work perform a full reset
  * @silence_err_logs: flag to silence error logs
  * @dev_cmd: ufs device management command information
  * @last_dme_cmd_tstamp: time stamp of the last completed DME command
@@ -710,6 +717,7 @@ struct ufs_hba {
 	bool is_powered;
 
 	/* Work Queues */
+	struct workqueue_struct *eh_wq;
 	struct work_struct eh_work;
 	struct work_struct eeh_work;
 
@@ -719,6 +727,7 @@ struct ufs_hba {
 	u32 saved_err;
 	u32 saved_uic_err;
 	struct ufs_stats ufs_stats;
+	bool force_reset;
 	bool silence_err_logs;
 
 	/* Device management request data */
-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

[PATCH v9 6/9] scsi: ufs: Recover hba runtime PM error in error handler

[Can Guo]

Current error handler cannot work well or recover hba runtime PM error if
ufshcd_suspend/resume has failed due to UFS errors, e.g. hibern8 enter/exit
error or SSU cmd error. When this happens, error handler may fail doing
full reset and restore because error handler always assumes that powers,
IRQs and clocks are ready after pm_runtime_get_sync returns, but actually
they are not if ufshcd_reusme fails [1]. Besides, if ufschd_suspend/resume
fails due to UFS error, runtime PM framework saves the error value to
dev.power.runtime_error. After that, hba dev runtime suspend/resume would
not be invoked anymore unless runtime_error is cleared [2].

In case of ufshcd_suspend/resume fails due to UFS errors, for scenario [1],
error handler cannot assume anything of pm_runtime_get_sync, meaning error
handler should explicitly turn ON powers, IRQs and clocks again. To get the
hba runtime PM work as regard for scenario [2], error handler can clear the
runtime_error by calling pm_runtime_set_active() if full reset and restore
succeeds. And, more important, if pm_runtime_set_active() returns no error,
which means runtime_error has been cleared, we also need to resume those
scsi devices under hba in case any of them has failed to be resumed due to
hba runtime resume failure. This is to unblock blk_queue_enter in case
there are bios waiting inside it.

Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
---
 drivers/scsi/ufs/ufshcd.c | 108 ++++++++++++++++++++++++++++++++++++++++++----
 1 file changed, 99 insertions(+), 9 deletions(-)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 2604016..6a10003 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -15,6 +15,7 @@
 #include <linux/of.h>
 #include <linux/bitfield.h>
 #include <linux/blk-pm.h>
+#include <linux/blkdev.h>
 #include "ufshcd.h"
 #include "ufs_quirks.h"
 #include "unipro.h"
@@ -229,6 +230,10 @@ static irqreturn_t ufshcd_intr(int irq, void *__hba);
 static int ufshcd_change_power_mode(struct ufs_hba *hba,
 			     struct ufs_pa_layer_attr *pwr_mode);
 static void ufshcd_schedule_eh_work(struct ufs_hba *hba);
+static int ufshcd_setup_hba_vreg(struct ufs_hba *hba, bool on);
+static int ufshcd_setup_vreg(struct ufs_hba *hba, bool on);
+static inline int ufshcd_config_vreg_hpm(struct ufs_hba *hba,
+					 struct ufs_vreg *vreg);
 static int ufshcd_wb_buf_flush_enable(struct ufs_hba *hba);
 static int ufshcd_wb_buf_flush_disable(struct ufs_hba *hba);
 static int ufshcd_wb_ctrl(struct ufs_hba *hba, bool enable);
@@ -5553,6 +5558,84 @@ static inline void ufshcd_schedule_eh_work(struct ufs_hba *hba)
 	}
 }
 
+static void ufshcd_err_handling_prepare(struct ufs_hba *hba)
+{
+	pm_runtime_get_sync(hba->dev);
+	if (pm_runtime_suspended(hba->dev)) {
+		/*
+		 * Don't assume anything of pm_runtime_get_sync(), if
+		 * resume fails, irq and clocks can be OFF, and powers
+		 * can be OFF or in LPM.
+		 */
+		ufshcd_setup_hba_vreg(hba, true);
+		ufshcd_enable_irq(hba);
+		ufshcd_setup_vreg(hba, true);
+		ufshcd_config_vreg_hpm(hba, hba->vreg_info.vccq);
+		ufshcd_config_vreg_hpm(hba, hba->vreg_info.vccq2);
+		ufshcd_hold(hba, false);
+		if (!ufshcd_is_clkgating_allowed(hba))
+			ufshcd_setup_clocks(hba, true);
+		ufshcd_release(hba);
+		ufshcd_vops_resume(hba, UFS_RUNTIME_PM);
+	} else {
+		ufshcd_hold(hba, false);
+		if (hba->clk_scaling.is_allowed) {
+			cancel_work_sync(&hba->clk_scaling.suspend_work);
+			cancel_work_sync(&hba->clk_scaling.resume_work);
+			ufshcd_suspend_clkscaling(hba);
+		}
+	}
+}
+
+static void ufshcd_err_handling_unprepare(struct ufs_hba *hba)
+{
+	ufshcd_release(hba);
+	if (hba->clk_scaling.is_allowed)
+		ufshcd_resume_clkscaling(hba);
+	pm_runtime_put(hba->dev);
+}
+
+static inline bool ufshcd_err_handling_should_stop(struct ufs_hba *hba)
+{
+	return (hba->ufshcd_state == UFSHCD_STATE_ERROR ||
+		(!(hba->saved_err || hba->saved_uic_err || hba->force_reset ||
+			ufshcd_is_link_broken(hba))));
+}
+
+#ifdef CONFIG_PM
+static void ufshcd_recover_pm_error(struct ufs_hba *hba)
+{
+	struct Scsi_Host *shost = hba->host;
+	struct scsi_device *sdev;
+	struct request_queue *q;
+	int ret;
+
+	/*
+	 * Set RPM status of hba device to RPM_ACTIVE,
+	 * this also clears its runtime error.
+	 */
+	ret = pm_runtime_set_active(hba->dev);
+	/*
+	 * If hba device had runtime error, we also need to resume those
+	 * scsi devices under hba in case any of them has failed to be
+	 * resumed due to hba runtime resume failure. This is to unblock
+	 * blk_queue_enter in case there are bios waiting inside it.
+	 */
+	if (!ret) {
+		list_for_each_entry(sdev, &shost->__devices, siblings) {
+			q = sdev->request_queue;
+			if (q->dev && (q->rpm_status == RPM_SUSPENDED ||
+				       q->rpm_status == RPM_SUSPENDING))
+				pm_request_resume(q->dev);
+		}
+	}
+}
+#else
+static inline void ufshcd_recover_pm_error(struct ufs_hba *hba)
+{
+}
+#endif
+
 /**
  * ufshcd_err_handler - handle UFS errors that require s/w attention
  * @work: pointer to work structure
@@ -5570,9 +5653,7 @@ static void ufshcd_err_handler(struct work_struct *work)
 	hba = container_of(work, struct ufs_hba, eh_work);
 
 	spin_lock_irqsave(hba->host->host_lock, flags);
-	if (hba->ufshcd_state == UFSHCD_STATE_ERROR ||
-	    (!(hba->saved_err || hba->saved_uic_err || hba->force_reset ||
-		ufshcd_is_link_broken(hba)))) {
+	if (ufshcd_err_handling_should_stop(hba)) {
 		if (hba->ufshcd_state != UFSHCD_STATE_ERROR)
 			hba->ufshcd_state = UFSHCD_STATE_OPERATIONAL;
 		spin_unlock_irqrestore(hba->host->host_lock, flags);
@@ -5581,10 +5662,17 @@ static void ufshcd_err_handler(struct work_struct *work)
 	}
 	ufshcd_set_eh_in_progress(hba);
 	spin_unlock_irqrestore(hba->host->host_lock, flags);
-	pm_runtime_get_sync(hba->dev);
-	ufshcd_hold(hba, false);
-
+	ufshcd_err_handling_prepare(hba);
 	spin_lock_irqsave(hba->host->host_lock, flags);
+	/*
+	 * A full reset and restore might have happened after preparation
+	 * is finished, double check whether we should stop.
+	 */
+	if (ufshcd_err_handling_should_stop(hba)) {
+		if (hba->ufshcd_state != UFSHCD_STATE_ERROR)
+			hba->ufshcd_state = UFSHCD_STATE_OPERATIONAL;
+		goto out;
+	}
 	hba->ufshcd_state = UFSHCD_STATE_RESET;
 
 	/* Complete requests that have door-bell cleared by h/w */
@@ -5662,10 +5750,12 @@ static void ufshcd_err_handler(struct work_struct *work)
 		hba->force_reset = false;
 		spin_unlock_irqrestore(hba->host->host_lock, flags);
 		err = ufshcd_reset_and_restore(hba);
-		spin_lock_irqsave(hba->host->host_lock, flags);
 		if (err)
 			dev_err(hba->dev, "%s: reset and restore failed with err %d\n",
 					__func__, err);
+		else
+			ufshcd_recover_pm_error(hba);
+		spin_lock_irqsave(hba->host->host_lock, flags);
 	}
 
 skip_err_handling:
@@ -5677,11 +5767,11 @@ static void ufshcd_err_handler(struct work_struct *work)
 			    __func__, hba->saved_err, hba->saved_uic_err);
 	}
 
+out:
 	ufshcd_clear_eh_in_progress(hba);
 	spin_unlock_irqrestore(hba->host->host_lock, flags);
 	ufshcd_scsi_unblock_requests(hba);
-	ufshcd_release(hba);
-	pm_runtime_put_sync(hba->dev);
+	ufshcd_err_handling_unprepare(hba);
 }
 
 /**
-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

[PATCH v9 7/9] scsi: ufs: Move dumps in IRQ handler to error handler

[Can Guo]

Sometime dumps in IRQ handler are heavy enough to cause system stability
issues, move them to error handler and only print basic host regs here.

Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
---
 drivers/scsi/ufs/ufshcd.c | 23 +++++++++++++++--------
 1 file changed, 15 insertions(+), 8 deletions(-)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 6a10003..a79fbbd 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -5696,6 +5696,19 @@ static void ufshcd_err_handler(struct work_struct *work)
 				    UFSHCD_UIC_DL_TCx_REPLAY_ERROR))))
 		needs_reset = true;
 
+	if (hba->saved_err & (INT_FATAL_ERRORS | UIC_ERROR |
+			      UFSHCD_UIC_HIBERN8_MASK)) {
+		bool pr_prdt = !!(hba->saved_err & SYSTEM_BUS_FATAL_ERROR);
+
+		spin_unlock_irqrestore(hba->host->host_lock, flags);
+		ufshcd_print_host_state(hba);
+		ufshcd_print_pwr_info(hba);
+		ufshcd_print_host_regs(hba);
+		ufshcd_print_tmrs(hba, hba->outstanding_tasks);
+		ufshcd_print_trs(hba, hba->outstanding_reqs, pr_prdt);
+		spin_lock_irqsave(hba->host->host_lock, flags);
+	}
+
 	/*
 	 * if host reset is required then skip clearing the pending
 	 * transfers forcefully because they will get cleared during
@@ -5915,18 +5928,12 @@ static irqreturn_t ufshcd_check_errors(struct ufs_hba *hba)
 
 		/* dump controller state before resetting */
 		if (hba->saved_err & (INT_FATAL_ERRORS | UIC_ERROR)) {
-			bool pr_prdt = !!(hba->saved_err &
-					SYSTEM_BUS_FATAL_ERROR);
-
 			dev_err(hba->dev, "%s: saved_err 0x%x saved_uic_err 0x%x\n",
 					__func__, hba->saved_err,
 					hba->saved_uic_err);
-
-			ufshcd_print_host_regs(hba);
+			ufshcd_dump_regs(hba, 0, UFSHCI_REG_SPACE_SIZE,
+					 "host_regs: ");
 			ufshcd_print_pwr_info(hba);
-			ufshcd_print_tmrs(hba, hba->outstanding_tasks);
-			ufshcd_print_trs(hba, hba->outstanding_reqs,
-					pr_prdt);
 		}
 		ufshcd_schedule_eh_work(hba);
 		retval |= IRQ_HANDLED;
-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

Re: [PATCH v9 7/9] scsi: ufs: Move dumps in IRQ handler to error handler

[Asutosh Das (asd)]

On 8/3/2020 2:04 AM, Can Guo wrote:
> Sometime dumps in IRQ handler are heavy enough to cause system stability
> issues, move them to error handler and only print basic host regs here.
> 
> Signed-off-by: Can Guo <cang@codeaurora.org>
> Reviewed-by: Bean Huo <beanhuo@micron.com>
> ---

Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>

>   drivers/scsi/ufs/ufshcd.c | 23 +++++++++++++++--------
>   1 file changed, 15 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
> index 6a10003..a79fbbd 100644
> --- a/drivers/scsi/ufs/ufshcd.c
> +++ b/drivers/scsi/ufs/ufshcd.c
> @@ -5696,6 +5696,19 @@ static void ufshcd_err_handler(struct work_struct *work)
>   				    UFSHCD_UIC_DL_TCx_REPLAY_ERROR))))
>   		needs_reset = true;
>   
> +	if (hba->saved_err & (INT_FATAL_ERRORS | UIC_ERROR |
> +			      UFSHCD_UIC_HIBERN8_MASK)) {
> +		bool pr_prdt = !!(hba->saved_err & SYSTEM_BUS_FATAL_ERROR);
> +
> +		spin_unlock_irqrestore(hba->host->host_lock, flags);
> +		ufshcd_print_host_state(hba);
> +		ufshcd_print_pwr_info(hba);
> +		ufshcd_print_host_regs(hba);
> +		ufshcd_print_tmrs(hba, hba->outstanding_tasks);
> +		ufshcd_print_trs(hba, hba->outstanding_reqs, pr_prdt);
> +		spin_lock_irqsave(hba->host->host_lock, flags);
> +	}
> +
>   	/*
>   	 * if host reset is required then skip clearing the pending
>   	 * transfers forcefully because they will get cleared during
> @@ -5915,18 +5928,12 @@ static irqreturn_t ufshcd_check_errors(struct ufs_hba *hba)
>   
>   		/* dump controller state before resetting */
>   		if (hba->saved_err & (INT_FATAL_ERRORS | UIC_ERROR)) {
> -			bool pr_prdt = !!(hba->saved_err &
> -					SYSTEM_BUS_FATAL_ERROR);
> -
>   			dev_err(hba->dev, "%s: saved_err 0x%x saved_uic_err 0x%x\n",
>   					__func__, hba->saved_err,
>   					hba->saved_uic_err);
> -
> -			ufshcd_print_host_regs(hba);
> +			ufshcd_dump_regs(hba, 0, UFSHCI_REG_SPACE_SIZE,
> +					 "host_regs: ");
>   			ufshcd_print_pwr_info(hba);
> -			ufshcd_print_tmrs(hba, hba->outstanding_tasks);
> -			ufshcd_print_trs(hba, hba->outstanding_reqs,
> -					pr_prdt);
>   		}
>   		ufshcd_schedule_eh_work(hba);
>   		retval |= IRQ_HANDLED;
> 


-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
Linux Foundation Collaborative Project

[PATCH v9 8/9] scsi: ufs: Fix a racing problem btw error handler and runtime PM ops

[Can Guo]

Current IRQ handler blocks scsi requests before scheduling eh_work, when
error handler calls pm_runtime_get_sync, if ufshcd_suspend/resume sends a
scsi cmd, most likely the SSU cmd, since scsi requests are blocked,
pm_runtime_get_sync() will never return because ufshcd_suspend/reusme is
blocked by the scsi cmd. Some changes and code re-arrangement can be made
to resolve it.

o In queuecommand path, hba->ufshcd_state check and ufshcd_send_command
  should stay into the same spin lock. This is to make sure that no more
  commands leak into doorbell after hba->ufshcd_state is changed.
o Don't block scsi requests before scheduling eh_work, let error handler
  block scsi requests when it is ready to start error recovery.
o Don't let scsi layer keep requeuing the scsi cmds sent from hba runtime
  PM ops, let them pass or fail them. Let them pass if eh_work is scheduled
  due to non-fatal errors. Fail them if eh_work is scheduled due to fatal
  errors, otherwise the cmds may eventually time out since UFS is in bad
  state, which gets error handler blocked for too long. If we fail the scsi
  cmds sent from hba runtime PM ops, hba runtime PM ops fails too, but it
  does not hurt since error handler can recover hba runtime PM error.

Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
---
 drivers/scsi/ufs/ufshcd.c | 84 ++++++++++++++++++++++++++++-------------------
 1 file changed, 50 insertions(+), 34 deletions(-)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index a79fbbd..d7d2758 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -126,7 +126,8 @@ enum {
 	UFSHCD_STATE_RESET,
 	UFSHCD_STATE_ERROR,
 	UFSHCD_STATE_OPERATIONAL,
-	UFSHCD_STATE_EH_SCHEDULED,
+	UFSHCD_STATE_EH_SCHEDULED_FATAL,
+	UFSHCD_STATE_EH_SCHEDULED_NON_FATAL,
 };
 
 /* UFSHCD error handling flags */
@@ -2515,34 +2516,6 @@ static int ufshcd_queuecommand(struct Scsi_Host *host, struct scsi_cmnd *cmd)
 	if (!down_read_trylock(&hba->clk_scaling_lock))
 		return SCSI_MLQUEUE_HOST_BUSY;
 
-	spin_lock_irqsave(hba->host->host_lock, flags);
-	switch (hba->ufshcd_state) {
-	case UFSHCD_STATE_OPERATIONAL:
-		break;
-	case UFSHCD_STATE_EH_SCHEDULED:
-	case UFSHCD_STATE_RESET:
-		err = SCSI_MLQUEUE_HOST_BUSY;
-		goto out_unlock;
-	case UFSHCD_STATE_ERROR:
-		set_host_byte(cmd, DID_ERROR);
-		cmd->scsi_done(cmd);
-		goto out_unlock;
-	default:
-		dev_WARN_ONCE(hba->dev, 1, "%s: invalid state %d\n",
-				__func__, hba->ufshcd_state);
-		set_host_byte(cmd, DID_BAD_TARGET);
-		cmd->scsi_done(cmd);
-		goto out_unlock;
-	}
-
-	/* if error handling is in progress, don't issue commands */
-	if (ufshcd_eh_in_progress(hba)) {
-		set_host_byte(cmd, DID_ERROR);
-		cmd->scsi_done(cmd);
-		goto out_unlock;
-	}
-	spin_unlock_irqrestore(hba->host->host_lock, flags);
-
 	hba->req_abort_count = 0;
 
 	err = ufshcd_hold(hba, true);
@@ -2578,11 +2551,50 @@ static int ufshcd_queuecommand(struct Scsi_Host *host, struct scsi_cmnd *cmd)
 	/* Make sure descriptors are ready before ringing the doorbell */
 	wmb();
 
-	/* issue command to the controller */
 	spin_lock_irqsave(hba->host->host_lock, flags);
+	switch (hba->ufshcd_state) {
+	case UFSHCD_STATE_OPERATIONAL:
+	case UFSHCD_STATE_EH_SCHEDULED_NON_FATAL:
+		break;
+	case UFSHCD_STATE_EH_SCHEDULED_FATAL:
+		/*
+		 * pm_runtime_get_sync() is used at error handling preparation
+		 * stage. If a scsi cmd, e.g. the SSU cmd, is sent from hba's
+		 * PM ops, it can never be finished if we let SCSI layer keep
+		 * retrying it, which gets err handler stuck forever. Neither
+		 * can we let the scsi cmd pass through, because UFS is in bad
+		 * state, the scsi cmd may eventually time out, which will get
+		 * err handler blocked for too long. So, just fail the scsi cmd
+		 * sent from PM ops, err handler can recover PM error anyways.
+		 */
+		if (hba->pm_op_in_progress) {
+			hba->force_reset = true;
+			set_host_byte(cmd, DID_BAD_TARGET);
+			goto out_compl_cmd;
+		}
+	case UFSHCD_STATE_RESET:
+		err = SCSI_MLQUEUE_HOST_BUSY;
+		goto out_compl_cmd;
+	case UFSHCD_STATE_ERROR:
+		set_host_byte(cmd, DID_ERROR);
+		goto out_compl_cmd;
+	default:
+		dev_WARN_ONCE(hba->dev, 1, "%s: invalid state %d\n",
+				__func__, hba->ufshcd_state);
+		set_host_byte(cmd, DID_BAD_TARGET);
+		goto out_compl_cmd;
+	}
 	ufshcd_send_command(hba, tag);
-out_unlock:
 	spin_unlock_irqrestore(hba->host->host_lock, flags);
+	goto out;
+
+out_compl_cmd:
+	scsi_dma_unmap(lrbp->cmd);
+	lrbp->cmd = NULL;
+	spin_unlock_irqrestore(hba->host->host_lock, flags);
+	ufshcd_release(hba);
+	if (!err)
+		cmd->scsi_done(cmd);
 out:
 	up_read(&hba->clk_scaling_lock);
 	return err;
@@ -5552,9 +5564,12 @@ static inline void ufshcd_schedule_eh_work(struct ufs_hba *hba)
 {
 	/* handle fatal errors only when link is not in error state */
 	if (hba->ufshcd_state != UFSHCD_STATE_ERROR) {
-		hba->ufshcd_state = UFSHCD_STATE_EH_SCHEDULED;
-		if (queue_work(hba->eh_wq, &hba->eh_work))
-			ufshcd_scsi_block_requests(hba);
+		if (hba->force_reset || ufshcd_is_link_broken(hba) ||
+		    ufshcd_is_saved_err_fatal(hba))
+			hba->ufshcd_state = UFSHCD_STATE_EH_SCHEDULED_FATAL;
+		else
+			hba->ufshcd_state = UFSHCD_STATE_EH_SCHEDULED_NON_FATAL;
+		queue_work(hba->eh_wq, &hba->eh_work);
 	}
 }
 
@@ -5664,6 +5679,7 @@ static void ufshcd_err_handler(struct work_struct *work)
 	spin_unlock_irqrestore(hba->host->host_lock, flags);
 	ufshcd_err_handling_prepare(hba);
 	spin_lock_irqsave(hba->host->host_lock, flags);
+	ufshcd_scsi_block_requests(hba);
 	/*
 	 * A full reset and restore might have happened after preparation
 	 * is finished, double check whether we should stop.
-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

Re: [PATCH v9 8/9] scsi: ufs: Fix a racing problem btw error handler and runtime PM ops

[Martin K. Petersen]

Can,

> Current IRQ handler blocks scsi requests before scheduling eh_work,
> when error handler calls pm_runtime_get_sync, if ufshcd_suspend/resume
> sends a scsi cmd, most likely the SSU cmd, since scsi requests are
> blocked, pm_runtime_get_sync() will never return because
> ufshcd_suspend/reusme is blocked by the scsi cmd. Some changes and
> code re-arrangement can be made to resolve it.

  CC [M]  drivers/scsi/ufs/ufshcd.o
drivers/scsi/ufs/ufshcd.c: In function ‘ufshcd_queuecommand’:
drivers/scsi/ufs/ufshcd.c:2570:6: error: this statement may fall through [-Werror=implicit-fallthrough=]
 2570 |   if (hba->pm_op_in_progress) {
      |      ^
drivers/scsi/ufs/ufshcd.c:2575:2: note: here
 2575 |  case UFSHCD_STATE_RESET:
      |  ^~~~
cc1: all warnings being treated as errors
make[3]: *** [scripts/Makefile.build:280: drivers/scsi/ufs/ufshcd.o] Error 1
make[2]: *** [scripts/Makefile.build:497: drivers/scsi/ufs] Error 2
make[1]: *** [scripts/Makefile.build:497: drivers/scsi] Error 2
make: *** [Makefile:1764: drivers] Error 2

-- 
Martin K. Petersen	Oracle Linux Engineering

Re: [PATCH v9 8/9] scsi: ufs: Fix a racing problem btw error handler and runtime PM ops

[Can Guo]

On 2020-08-05 09:31, Martin K. Petersen wrote:
> Can,
> 
>> Current IRQ handler blocks scsi requests before scheduling eh_work,
>> when error handler calls pm_runtime_get_sync, if ufshcd_suspend/resume
>> sends a scsi cmd, most likely the SSU cmd, since scsi requests are
>> blocked, pm_runtime_get_sync() will never return because
>> ufshcd_suspend/reusme is blocked by the scsi cmd. Some changes and
>> code re-arrangement can be made to resolve it.
> 
>   CC [M]  drivers/scsi/ufs/ufshcd.o
> drivers/scsi/ufs/ufshcd.c: In function ‘ufshcd_queuecommand’:
> drivers/scsi/ufs/ufshcd.c:2570:6: error: this statement may fall
> through [-Werror=implicit-fallthrough=]
>  2570 |   if (hba->pm_op_in_progress) {
>       |      ^
> drivers/scsi/ufs/ufshcd.c:2575:2: note: here
>  2575 |  case UFSHCD_STATE_RESET:
>       |  ^~~~
> cc1: all warnings being treated as errors
> make[3]: *** [scripts/Makefile.build:280: drivers/scsi/ufs/ufshcd.o] 
> Error 1
> make[2]: *** [scripts/Makefile.build:497: drivers/scsi/ufs] Error 2
> make[1]: *** [scripts/Makefile.build:497: drivers/scsi] Error 2
> make: *** [Makefile:1764: drivers] Error 2

Thanks Martin, will fix it in next version.

Can Guo.

[PATCH v9 9/9] scsi: ufs: Properly release resources if a task is aborted successfully

[Can Guo]

In current UFS task abort hook, namely ufshcd_abort(), if a task is
aborted successfully, clock scaling busy time statistics is not updated
and, most important, clk_gating.active_reqs is not decreased, which makes
clk_gating.active_reqs stay above zero forever, thus clock gating would
never happen. To fix it, instead of releasing resources "mannually", use
the existing func __ufshcd_transfer_req_compl(). This can also eliminate
racing of scsi_dma_unmap() from the real completion in IRQ handler path.

Signed-off-by: Can Guo <cang@codeaurora.org>
CC: Stanley Chu <stanley.chu@mediatek.com>
---
 drivers/scsi/ufs/ufshcd.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index d7d2758..9a48389 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -6635,11 +6635,8 @@ static int ufshcd_abort(struct scsi_cmnd *cmd)
 		goto out;
 	}
 
-	scsi_dma_unmap(cmd);
-
 	spin_lock_irqsave(host->host_lock, flags);
-	ufshcd_outstanding_req_clear(hba, tag);
-	hba->lrb[tag].cmd = NULL;
+	__ufshcd_transfer_req_compl(hba, (1UL << tag));
 	spin_unlock_irqrestore(host->host_lock, flags);
 
 out:
-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

Re: [PATCH v9 9/9] scsi: ufs: Properly release resources if a task is aborted successfully

[Stanley Chu]

On Mon, 2020-08-03 at 02:04 -0700, Can Guo wrote:
> In current UFS task abort hook, namely ufshcd_abort(), if a task is
> aborted successfully, clock scaling busy time statistics is not updated
> and, most important, clk_gating.active_reqs is not decreased, which makes
> clk_gating.active_reqs stay above zero forever, thus clock gating would
> never happen. To fix it, instead of releasing resources "mannually", use
> the existing func __ufshcd_transfer_req_compl(). This can also eliminate
> racing of scsi_dma_unmap() from the real completion in IRQ handler path.
> 
> Signed-off-by: Can Guo <cang@codeaurora.org>
> CC: Stanley Chu <stanley.chu@mediatek.com>
> ---
>  drivers/scsi/ufs/ufshcd.c | 5 +----
>  1 file changed, 1 insertion(+), 4 deletions(-)
> 
> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
> index d7d2758..9a48389 100644
> --- a/drivers/scsi/ufs/ufshcd.c
> +++ b/drivers/scsi/ufs/ufshcd.c
> @@ -6635,11 +6635,8 @@ static int ufshcd_abort(struct scsi_cmnd *cmd)
>  		goto out;
>  	}
>  
> -	scsi_dma_unmap(cmd);
> -
>  	spin_lock_irqsave(host->host_lock, flags);
> -	ufshcd_outstanding_req_clear(hba, tag);
> -	hba->lrb[tag].cmd = NULL;
> +	__ufshcd_transfer_req_compl(hba, (1UL << tag));
>  	spin_unlock_irqrestore(host->host_lock, flags);
>  
>  out:

Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>