[PATCH v2] ASoC: cs42l51: manage mclk shutdown delay

[PATCH v2] ASoC: cs42l51: manage mclk shutdown delay

[Olivier Moysan]

A delay must be introduced before the shutdown down of the mclk,
as stated in CS42L51 datasheet. Otherwise the codec may
produce some noise after the end of DAPM power down sequence.
The delay between DAC and CLOCK_SUPPLY widgets is too short.
Add a delay in mclk shutdown request to manage the shutdown delay
explicitly. From experiments, at least 10ms delay is necessary.
Set delay to 20ms as recommended in Documentation/timers/timers-howto.rst
when using msleep().

Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
---
Recommended Power-Down Sequence:
(see https://statics.cirrus.com/pubs/proDatasheet/CS42L51_F2.pdf)
1.    Mute the DACs and ADCs.
2.    Disable soft ramp and zero-cross volume transitions
3.    Set the PDN bit to 1.
4.    Wait at least 100 μs.
The codec will be fully powered down after this 100 μs delay.
Prior to the removal of the master clock(MCLK),
this delay of at least 100 μs must be implemented after step 3
to avoid premature disruption of the codec’s power down sequence.

Changes in v2:
- Manage explicitly DAPM events through a switch case in mclk_event()
---
 sound/soc/codecs/cs42l51.c | 22 +++++++++++++++++++++-
 1 file changed, 21 insertions(+), 1 deletion(-)

diff --git a/sound/soc/codecs/cs42l51.c b/sound/soc/codecs/cs42l51.c
index 097c4e8d9950..c61b17dc2af8 100644
--- a/sound/soc/codecs/cs42l51.c
+++ b/sound/soc/codecs/cs42l51.c
@@ -254,8 +254,28 @@ static const struct snd_soc_dapm_widget cs42l51_dapm_widgets[] = {
 		&cs42l51_adcr_mux_controls),
 };
 
+static int mclk_event(struct snd_soc_dapm_widget *w,
+		      struct snd_kcontrol *kcontrol, int event)
+{
+	struct snd_soc_component *comp = snd_soc_dapm_to_component(w->dapm);
+	struct cs42l51_private *cs42l51 = snd_soc_component_get_drvdata(comp);
+
+	switch (event) {
+	case SND_SOC_DAPM_PRE_PMU:
+		return clk_prepare_enable(cs42l51->mclk_handle);
+	case SND_SOC_DAPM_POST_PMD:
+		/* Delay mclk shutdown to fulfill power-down sequence requirements */
+		msleep(20);
+		clk_disable_unprepare(cs42l51->mclk_handle);
+		break;
+	}
+
+	return 0;
+}
+
 static const struct snd_soc_dapm_widget cs42l51_dapm_mclk_widgets[] = {
-	SND_SOC_DAPM_CLOCK_SUPPLY("MCLK")
+	SND_SOC_DAPM_SUPPLY("MCLK", SND_SOC_NOPM, 0, 0, mclk_event,
+			    SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD),
 };
 
 static const struct snd_soc_dapm_route cs42l51_routes[] = {
-- 
2.17.1

Re: [PATCH v2] ASoC: cs42l51: manage mclk shutdown delay

[Mark Brown]

On Tue, 20 Oct 2020 17:01:09 +0200, Olivier Moysan wrote:
> A delay must be introduced before the shutdown down of the mclk,
> as stated in CS42L51 datasheet. Otherwise the codec may
> produce some noise after the end of DAPM power down sequence.
> The delay between DAC and CLOCK_SUPPLY widgets is too short.
> Add a delay in mclk shutdown request to manage the shutdown delay
> explicitly. From experiments, at least 10ms delay is necessary.
> Set delay to 20ms as recommended in Documentation/timers/timers-howto.rst
> when using msleep().

Applied to

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next

Thanks!

[1/1] ASoC: cs42l51: manage mclk shutdown delay
      commit: 20afe581c9b980848ad097c4d54dde9bec7593ef

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark