[PATCH v3 1/2] regulator: rt6160: Add DT binding document for Richtek RT6160

[PATCH v3 1/2] regulator: rt6160: Add DT binding document for Richtek RT6160

[cy_huang]

From: ChiYuan Huang <cy_huang@richtek.com>

Add DT binding document for Richtek RT6160 voltage regulator.

Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
---
since v3
- Move all regulator related properties to the upper node.

since v2
- Move buckboost node from patternProperties to Properties.
---
 .../regulator/richtek,rt6160-regulator.yaml        | 61 ++++++++++++++++++++++
 1 file changed, 61 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/richtek,rt6160-regulator.yaml

diff --git a/Documentation/devicetree/bindings/regulator/richtek,rt6160-regulator.yaml b/Documentation/devicetree/bindings/regulator/richtek,rt6160-regulator.yaml
new file mode 100644
index 00000000..0534b0d
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/richtek,rt6160-regulator.yaml
@@ -0,0 +1,61 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/richtek,rt6160-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Richtek RT6160 BuckBoost converter
+
+maintainers:
+  - ChiYuan Huang <cy_huang@richtek.com>
+
+description: |
+  The RT6160 is a high-efficiency buck-boost converter that can provide
+  up to 3A output current from 2025mV to 5200mV. And it support the wide
+  input voltage range from 2200mV to 5500mV.
+
+  Datasheet is available at
+  https://www.richtek.com/assets/product_file/RT6160A/DS6160A-00.pdf
+
+allOf:
+  - $ref: regulator.yaml#
+
+properties:
+  compatible:
+    enum:
+      - richtek,rt6160
+
+  reg:
+    maxItems: 1
+
+  enable-gpios:
+    description: A connection of the 'enable' gpio line.
+    maxItems: 1
+
+  richtek,vsel-active-low:
+    description: |
+      Used to indicate the 'vsel' pin active level. if not specified, use
+      high active level as the default.
+    type: boolean
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      rt6160@75 {
+        compatible = "richtek,rt6160";
+        reg = <0x75>;
+        enable-gpios = <&gpio26 2 0>;
+        regulator-name = "rt6160-buckboost";
+        regulator-min-microvolt = <2025000>;
+        regulator-max-microvolt = <5200000>;
+      };
+    };
-- 
2.7.4

[PATCH v3 2/2] regulator: rt6160: Add support for Richtek RT6160

[cy_huang]

From: ChiYuan Huang <cy_huang@richtek.com>

Add support for Richtek RT6160 voltage regulator. It can provide up
to 3A output current within the adjustable voltage from 2025mV
to 5200mV. It integrate a buckboost converter to support wide input
voltage range from 2200mV to 5500mV.

Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
---
since v3
- Use more header file like as of_regulator.h and property.h.
- Change the parsing string from 'richtek,vsel_active_low' to 'richtek,vsel-active-low'.
- Use of_get_regulator_init_data to get the regulator init_data.

since v2
- Fix W=1 warning for of_device_id.
---
 drivers/regulator/Kconfig            |  11 ++
 drivers/regulator/Makefile           |   1 +
 drivers/regulator/rt6160-regulator.c | 269 +++++++++++++++++++++++++++++++++++
 3 files changed, 281 insertions(+)
 create mode 100644 drivers/regulator/rt6160-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 9d84d92..4fe7ddc 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -1030,6 +1030,17 @@ config REGULATOR_RT5033
 	  RT5033 PMIC. The device supports multiple regulators like
 	  current source, LDO and Buck.
 
+config REGULATOR_RT6160
+	tristate "Richtek RT6160 BuckBoost voltage regulator"
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  This adds support for voltage regulator in Richtek RT6160.
+	  This device automatically change voltage output mode from
+	  Buck or Boost. The mode transistion depend on the input source voltage.
+	  The wide output range is from 2025mV to 5200mV and can be used on most
+	  common application scenario.
+
 config REGULATOR_RTMV20
 	tristate "RTMV20 Laser Diode Regulator"
 	depends on I2C
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 580b015..5b2c93e 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -124,6 +124,7 @@ obj-$(CONFIG_REGULATOR_ROHM)	+= rohm-regulator.o
 obj-$(CONFIG_REGULATOR_RT4801)	+= rt4801-regulator.o
 obj-$(CONFIG_REGULATOR_RT4831)	+= rt4831-regulator.o
 obj-$(CONFIG_REGULATOR_RT5033)	+= rt5033-regulator.o
+obj-$(CONFIG_REGULATOR_RT6160)	+= rt6160-regulator.o
 obj-$(CONFIG_REGULATOR_RTMV20)	+= rtmv20-regulator.o
 obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
 obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
diff --git a/drivers/regulator/rt6160-regulator.c b/drivers/regulator/rt6160-regulator.c
new file mode 100644
index 00000000..4483c17
--- /dev/null
+++ b/drivers/regulator/rt6160-regulator.c
@@ -0,0 +1,269 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+#define RT6160_MODE_AUTO	0
+#define RT6160_MODE_FPWM	1
+
+#define RT6160_REG_CNTL		0x01
+#define RT6160_REG_STATUS	0x02
+#define RT6160_REG_DEVID	0x03
+#define RT6160_REG_VSELL	0x04
+#define RT6160_REG_VSELH	0x05
+
+#define RT6160_FPWM_MASK	BIT(3)
+#define RT6160_RAMPRATE_MASK	GENMASK(1, 0)
+#define RT6160_VID_MASK		GENMASK(7, 4)
+#define RT6160_VSEL_MASK	GENMASK(6, 0)
+#define RT6160_HDSTAT_MASK	BIT(4)
+#define RT6160_UVSTAT_MASK	BIT(3)
+#define RT6160_OCSTAT_MASK	BIT(2)
+#define RT6160_TSDSTAT_MASK	BIT(1)
+#define RT6160_PGSTAT_MASK	BIT(0)
+
+#define RT6160_RAMPRATE_1VMS	0
+#define RT6160_RAMPRATE_2P5VMS	1
+#define RT6160_RAMPRATE_5VMS	2
+#define RT6160_RAMPRATE_10VMS	3
+#define RT6160_VENDOR_ID	0xA0
+#define RT6160_VOUT_MINUV	2025000
+#define RT6160_VOUT_MAXUV	5200000
+#define RT6160_VOUT_STPUV	25000
+#define RT6160_N_VOUTS		((RT6160_VOUT_MAXUV - RT6160_VOUT_MINUV) / RT6160_VOUT_STPUV + 1)
+
+struct rt6160_priv {
+	struct regulator_desc desc;
+	bool vsel_active_low;
+};
+
+static int rt6160_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	unsigned int mode_val;
+
+	switch (mode) {
+	case REGULATOR_MODE_FAST:
+		mode_val = RT6160_FPWM_MASK;
+		break;
+	case REGULATOR_MODE_NORMAL:
+		mode_val = 0;
+		break;
+	default:
+		dev_err(&rdev->dev, "mode not supported\n");
+		return -EINVAL;
+	}
+
+	return regmap_update_bits(regmap, RT6160_REG_CNTL, RT6160_FPWM_MASK, mode_val);
+}
+
+static unsigned int rt6160_get_mode(struct regulator_dev *rdev)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	unsigned int val;
+	int ret;
+
+	ret = regmap_read(regmap, RT6160_REG_CNTL, &val);
+	if (ret)
+		return ret;
+
+	if (val & RT6160_FPWM_MASK)
+		return REGULATOR_MODE_FAST;
+
+	return REGULATOR_MODE_NORMAL;
+}
+
+static int rt6160_set_suspend_voltage(struct regulator_dev *rdev, int uV)
+{
+	struct rt6160_priv *priv = rdev_get_drvdata(rdev);
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	unsigned int reg = RT6160_REG_VSELH;
+	int vsel;
+
+	vsel = regulator_map_voltage_linear(rdev, uV, uV);
+	if (vsel < 0)
+		return vsel;
+
+	if (priv->vsel_active_low)
+		reg = RT6160_REG_VSELL;
+
+	return regmap_update_bits(regmap, reg, RT6160_VSEL_MASK, vsel);
+}
+
+static int rt6160_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	unsigned int ramp_value = RT6160_RAMPRATE_1VMS;
+
+	switch (ramp_delay) {
+	case 1 ... 1000:
+		ramp_value = RT6160_RAMPRATE_1VMS;
+		break;
+	case 1001 ... 2500:
+		ramp_value = RT6160_RAMPRATE_2P5VMS;
+		break;
+	case 2501 ... 5000:
+		ramp_value = RT6160_RAMPRATE_5VMS;
+		break;
+	case 5001 ... 10000:
+		ramp_value = RT6160_RAMPRATE_10VMS;
+		break;
+	default:
+		dev_warn(&rdev->dev, "ramp_delay %d not supported, setting 1000\n", ramp_delay);
+	}
+
+	return regmap_update_bits(regmap, RT6160_REG_CNTL, RT6160_RAMPRATE_MASK, ramp_value);
+}
+
+static int rt6160_get_error_flags(struct regulator_dev *rdev, unsigned int *flags)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	unsigned int val, events = 0;
+	int ret;
+
+	ret = regmap_read(regmap, RT6160_REG_STATUS, &val);
+	if (ret)
+		return ret;
+
+	if (val & (RT6160_HDSTAT_MASK | RT6160_TSDSTAT_MASK))
+		events |= REGULATOR_ERROR_OVER_TEMP;
+
+	if (val & RT6160_UVSTAT_MASK)
+		events |= REGULATOR_ERROR_UNDER_VOLTAGE;
+
+	if (val & RT6160_OCSTAT_MASK)
+		events |= REGULATOR_ERROR_OVER_CURRENT;
+
+	if (val & RT6160_PGSTAT_MASK)
+		events |= REGULATOR_ERROR_FAIL;
+
+	*flags = events;
+	return 0;
+}
+
+static const struct regulator_ops rt6160_regulator_ops = {
+	.list_voltage = regulator_list_voltage_linear,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+
+	.set_mode = rt6160_set_mode,
+	.get_mode = rt6160_get_mode,
+	.set_suspend_voltage = rt6160_set_suspend_voltage,
+	.set_ramp_delay = rt6160_set_ramp_delay,
+	.get_error_flags = rt6160_get_error_flags,
+};
+
+static unsigned int rt6160_of_map_mode(unsigned int mode)
+{
+	if (mode == RT6160_MODE_FPWM)
+		return REGULATOR_MODE_FAST;
+	else if (mode == RT6160_MODE_AUTO)
+		return REGULATOR_MODE_NORMAL;
+
+	return REGULATOR_MODE_INVALID;
+}
+
+static bool rt6160_is_accessible_reg(struct device *dev, unsigned int reg)
+{
+	if (reg >= RT6160_REG_CNTL && reg <= RT6160_REG_VSELH)
+		return true;
+	return false;
+}
+
+static const struct regmap_config rt6160_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = RT6160_REG_VSELH,
+
+	.writeable_reg = rt6160_is_accessible_reg,
+	.readable_reg = rt6160_is_accessible_reg,
+};
+
+static int rt6160_probe(struct i2c_client *i2c)
+{
+	struct rt6160_priv *priv;
+	struct regmap *regmap;
+	struct gpio_desc *enable_gpio;
+	struct regulator_config regulator_cfg = {};
+	struct regulator_dev *rdev;
+	unsigned int devid;
+	int ret;
+
+	priv = devm_kzalloc(&i2c->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->vsel_active_low = device_property_present(&i2c->dev, "richtek,vsel-active-low");
+
+	enable_gpio = devm_gpiod_get_optional(&i2c->dev, "enable", GPIOD_OUT_HIGH);
+	if (IS_ERR(enable_gpio)) {
+		dev_err(&i2c->dev, "Failed to get 'enable' gpio\n");
+		return PTR_ERR(enable_gpio);
+	}
+
+	regmap = devm_regmap_init_i2c(i2c, &rt6160_regmap_config);
+	if (IS_ERR(regmap)) {
+		dev_err(&i2c->dev, "Failed to init regmap\n");
+		return PTR_ERR(regmap);
+	}
+
+	ret = regmap_read(regmap, RT6160_REG_DEVID, &devid);
+	if (ret)
+		return ret;
+
+	if ((devid & RT6160_VID_MASK) != RT6160_VENDOR_ID) {
+		dev_err(&i2c->dev, "VID not correct [0x%02x]\n", devid);
+		return -ENODEV;
+	}
+
+	priv->desc.name = "rt6160-buckboost";
+	priv->desc.type = REGULATOR_VOLTAGE;
+	priv->desc.owner = THIS_MODULE;
+	priv->desc.min_uV = RT6160_VOUT_MINUV;
+	priv->desc.uV_step = RT6160_VOUT_STPUV;
+	priv->desc.vsel_reg = RT6160_REG_VSELH;
+	priv->desc.vsel_mask = RT6160_VSEL_MASK;
+	priv->desc.n_voltages = RT6160_N_VOUTS;
+	priv->desc.of_map_mode = rt6160_of_map_mode;
+	priv->desc.ops = &rt6160_regulator_ops;
+	if (priv->vsel_active_low)
+		priv->desc.vsel_reg = RT6160_REG_VSELL;
+
+	regulator_cfg.dev = &i2c->dev;
+	regulator_cfg.regmap = regmap;
+	regulator_cfg.driver_data = priv;
+	regulator_cfg.init_data = of_get_regulator_init_data(&i2c->dev, i2c->dev.of_node,
+							     &priv->desc);
+
+	rdev = devm_regulator_register(&i2c->dev, &priv->desc, &regulator_cfg);
+	if (IS_ERR(rdev)) {
+		dev_err(&i2c->dev, "Failed to register regulator\n");
+		return PTR_ERR(rdev);
+	}
+
+	return 0;
+}
+
+static const struct of_device_id __maybe_unused rt6160_of_match_table[] = {
+	{ .compatible = "richtek,rt6160", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, rt6160_of_match_table);
+
+static struct i2c_driver rt6160_driver = {
+	.driver = {
+		.name = "rt6160",
+		.of_match_table = rt6160_of_match_table,
+	},
+	.probe_new = rt6160_probe,
+};
+module_i2c_driver(rt6160_driver);
+
+MODULE_AUTHOR("ChiYuan Huang <cy_huang@richtek.com>");
+MODULE_LICENSE("GPL v2");
-- 
2.7.4

Re: [PATCH v3 1/2] regulator: rt6160: Add DT binding document for Richtek RT6160

[Rob Herring]

On Wed, 19 May 2021 14:43:58 +0800, cy_huang wrote:
> From: ChiYuan Huang <cy_huang@richtek.com>
> 
> Add DT binding document for Richtek RT6160 voltage regulator.
> 
> Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
> ---
> since v3
> - Move all regulator related properties to the upper node.
> 
> since v2
> - Move buckboost node from patternProperties to Properties.
> ---
>  .../regulator/richtek,rt6160-regulator.yaml        | 61 ++++++++++++++++++++++
>  1 file changed, 61 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/regulator/richtek,rt6160-regulator.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>