From: Kewei Xu <kewei.xu@mediatek.com>
To: <wsa@the-dreams.de>
Cc: <matthias.bgg@gmail.com>, <robh+dt@kernel.org>,
<linux-i2c@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>,
<linux-mediatek@lists.infradead.org>,
<srv_heupstream@mediatek.com>, <leilk.liu@mediatek.com>,
<qii.wang@mediatek.com>, <liguo.zhang@mediatek.com>,
<caiyu.chen@mediatek.com>, <ot_daolong.zhu@mediatek.com>,
<yuhan.wei@mediatek.com>, <kewei.xu@mediatek.com>
Subject: [RESEND PATCH v5 2/7] i2c: mediatek: Reset the handshake signal between i2c and dma
Date: Tue, 24 Aug 2021 11:30:23 +0800 [thread overview]
Message-ID: <1629775828-19993-3-git-send-email-kewei.xu@mediatek.com> (raw)
In-Reply-To: <1629775828-19993-1-git-send-email-kewei.xu@mediatek.com>
Due to changes in the hardware design of the handshaking signal
between i2c and dma, it is necessary to reset the handshaking
signal before each transfer to ensure that the multi-msgs can
be transferred correctly.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
---
drivers/i2c/busses/i2c-mt65xx.c | 26 ++++++++++++++++++++++++++
1 file changed, 26 insertions(+)
diff --git a/drivers/i2c/busses/i2c-mt65xx.c b/drivers/i2c/busses/i2c-mt65xx.c
index 2661ed0..abda525 100644
--- a/drivers/i2c/busses/i2c-mt65xx.c
+++ b/drivers/i2c/busses/i2c-mt65xx.c
@@ -15,6 +15,7 @@
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
+#include <linux/iopoll.h>
#include <linux/kernel.h>
#include <linux/mm.h>
#include <linux/module.h>
@@ -47,6 +48,9 @@
#define I2C_RD_TRANAC_VALUE 0x0001
#define I2C_SCL_MIS_COMP_VALUE 0x0000
#define I2C_CHN_CLR_FLAG 0x0000
+#define I2C_CLR_DEBUGCTR 0x0000
+#define I2C_RELIABILITY 0x0010
+#define I2C_DMAACK_ENABLE 0x0008
#define I2C_DMA_CON_TX 0x0000
#define I2C_DMA_CON_RX 0x0001
@@ -842,6 +846,7 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
u16 restart_flag = 0;
u16 dma_sync = 0;
u32 reg_4g_mode;
+ u32 reg_dma_reset;
u8 *dma_rd_buf = NULL;
u8 *dma_wr_buf = NULL;
dma_addr_t rpaddr = 0;
@@ -855,6 +860,27 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
reinit_completion(&i2c->msg_complete);
+ if (i2c->dev_comp->apdma_sync && left_num > 1) {
+ mtk_i2c_writew(i2c, I2C_CLR_DEBUGCTR, OFFSET_DEBUGCTRL);
+ writel(I2C_DMA_HANDSHAKE_RST | I2C_DMA_WARM_RST,
+ i2c->pdmabase + OFFSET_RST);
+
+ ret = readw_poll_timeout(i2c->pdmabase + OFFSET_RST,
+ reg_dma_reset,
+ !(reg_dma_reset & I2C_DMA_WARM_RST),
+ 0, 100);
+ if (ret) {
+ dev_err(i2c->dev, "DMA warm reset timeout\n");
+ return -ETIMEDOUT;
+ }
+
+ writel(I2C_DMA_CLR_FLAG, i2c->pdmabase + OFFSET_RST);
+ mtk_i2c_writew(i2c, I2C_HANDSHAKE_RST, OFFSET_SOFTRESET);
+ mtk_i2c_writew(i2c, I2C_CHN_CLR_FLAG, OFFSET_SOFTRESET);
+ mtk_i2c_writew(i2c, I2C_RELIABILITY | I2C_DMAACK_ENABLE,
+ OFFSET_DEBUGCTRL);
+ }
+
control_reg = mtk_i2c_readw(i2c, OFFSET_CONTROL) &
~(I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS);
if ((i2c->speed_hz > I2C_MAX_FAST_MODE_PLUS_FREQ) || (left_num >= 1))
--
1.9.1
next prev parent reply other threads:[~2021-08-24 3:30 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-08-24 3:30 [RESEND PATCH v5 0/7] Introducing an attribute to select the time setting Kewei Xu
2021-08-24 3:30 ` [RESEND PATCH v5 1/7] i2c: mediatek: fixing the incorrect register offset Kewei Xu
2021-08-24 3:30 ` Kewei Xu [this message]
2021-08-24 3:30 ` [RESEND PATCH v5 3/7] i2c: mediatek: Dump i2c/dma register when a timeout occurs Kewei Xu
2021-08-24 3:30 ` [RESEND PATCH v5 4/7] dt-bindings: i2c: add attribute use-default-timing Kewei Xu
2021-08-24 16:52 ` Rob Herring
2021-08-24 3:30 ` [RESEND PATCH v5 5/7] i2c: mediatek: Add OFFSET_EXT_CONF setting back Kewei Xu
2021-08-24 3:30 ` [RESEND PATCH v5 6/7] i2c: mediatek: Isolate speed setting via dts for special devices Kewei Xu
2021-08-24 3:30 ` [RESEND PATCH v5 7/7] i2c: mediatek: modify bus speed calculation formula Kewei Xu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1629775828-19993-3-git-send-email-kewei.xu@mediatek.com \
--to=kewei.xu@mediatek.com \
--cc=caiyu.chen@mediatek.com \
--cc=devicetree@vger.kernel.org \
--cc=leilk.liu@mediatek.com \
--cc=liguo.zhang@mediatek.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=matthias.bgg@gmail.com \
--cc=ot_daolong.zhu@mediatek.com \
--cc=qii.wang@mediatek.com \
--cc=robh+dt@kernel.org \
--cc=srv_heupstream@mediatek.com \
--cc=wsa@the-dreams.de \
--cc=yuhan.wei@mediatek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).