[PATCH v5 0/6] arm64: qcom: add Type-C Altmode support

[PATCH v5 0/6] arm64: qcom: add Type-C Altmode support

[Neil Armstrong]

This adds the missing bits to support the USB-C Altmode
support on SM8550.

These are the following changes since the previous SM8450 SoC:
- No more GLINK altmode events for USB only changes, only DP
- Type-C orientation is available on a PMIC signal connected
  to a GPIO line
- When altmode is disconnected, an 0xff mode event is sent.

The 0xff altmode is translated as a SAFE type-c mux mode.

The fact No more GLINK altmode events for USB needs to be resolved
in a separate patchset.

Redriver driver & bindings dependency at [1].

[1] https://lore.kernel.org/all/20230601-topic-sm8x50-upstream-redriver-v2-0-dda89b22b1c0@linaro.org/

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Changes in v5:
- switch to single port instead of ports for fsa node in MTP & QRD
- Link to v4: https://lore.kernel.org/r/20230601-topic-sm8550-upstream-type-c-v4-0-eb2ae960b8dc@linaro.org

Changes in v4:
- Drop the orientation gpio handling code and bindings until the situatin is resolved
- Link to v3: https://lore.kernel.org/r/20230601-topic-sm8550-upstream-type-c-v3-0-22c9973012b6@linaro.org

Changes in v3:
- Fix fsa node names in both QRD amd MTP nodes
- Add missing orientation-gpios in MTP dt
- Remove invalid svid property
- Link to v2: https://lore.kernel.org/r/20230601-topic-sm8550-upstream-type-c-v2-0-3bbdf37575c3@linaro.org

Changes in v2:
- Updated redriver node to use retimer-switch on QRD
- Fixed redriver data-lane according to v2 bindings
- Added review/ack tags
- Added new change to handle retimer-switch in pmic-glink altmode driver
- Link to v1: https://lore.kernel.org/r/20230601-topic-sm8550-upstream-type-c-v1-0-d4d97b4d8bab@linaro.org

---
Neil Armstrong (6):
      soc: qcom: pmic_glink_altmode: handle safe mode when disconnect
      qcom: pmic_glink_altmode: add retimer-switch support
      qcom: pmic_glink: enable altmode for SM8550
      arm64: dts: qcom: sm8550: add ports subnodes in usb/dp qmpphy node
      arm64: dts: qcom: sm8550-mtp: add pmic glink port/endpoints
      arm64: dts: qcom: sm8550-qrd: add pmic glink port/endpoints

 arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 59 ++++++++++++++++++++-
 arch/arm64/boot/dts/qcom/sm8550-qrd.dts | 91 ++++++++++++++++++++++++++++++++-
 arch/arm64/boot/dts/qcom/sm8550.dtsi    | 26 ++++++++++
 drivers/soc/qcom/pmic_glink.c           |  6 +--
 drivers/soc/qcom/pmic_glink_altmode.c   | 61 +++++++++++++++++++++-
 5 files changed, 233 insertions(+), 10 deletions(-)
---
base-commit: e602e10c923db4435573997d383a145ee38ae333
change-id: 20230601-topic-sm8550-upstream-type-c-e85b4d971450

Best regards,
-- 
Neil Armstrong <neil.armstrong@linaro.org>

[PATCH v5 1/6] soc: qcom: pmic_glink_altmode: handle safe mode when disconnect

[Neil Armstrong]

On some Qcom SoCs, the Altmode event mode is set to 0xff when
the Type-C port is disconnected.

Handle this specific mode and translate it as the SAFE mode.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 drivers/soc/qcom/pmic_glink_altmode.c | 18 +++++++++++++++++-
 1 file changed, 17 insertions(+), 1 deletion(-)

diff --git a/drivers/soc/qcom/pmic_glink_altmode.c b/drivers/soc/qcom/pmic_glink_altmode.c
index df48fbea4b68..007d308e2f15 100644
--- a/drivers/soc/qcom/pmic_glink_altmode.c
+++ b/drivers/soc/qcom/pmic_glink_altmode.c
@@ -173,6 +173,20 @@ static void pmic_glink_altmode_enable_usb(struct pmic_glink_altmode *altmode,
 		dev_err(altmode->dev, "failed to switch mux to USB\n");
 }
 
+static void pmic_glink_altmode_safe(struct pmic_glink_altmode *altmode,
+				    struct pmic_glink_altmode_port *port)
+{
+	int ret;
+
+	port->state.alt = NULL;
+	port->state.data = NULL;
+	port->state.mode = TYPEC_STATE_SAFE;
+
+	ret = typec_mux_set(port->typec_mux, &port->state);
+	if (ret)
+		dev_err(altmode->dev, "failed to switch mux to safe mode\n");
+}
+
 static void pmic_glink_altmode_worker(struct work_struct *work)
 {
 	struct pmic_glink_altmode_port *alt_port = work_to_altmode_port(work);
@@ -180,7 +194,9 @@ static void pmic_glink_altmode_worker(struct work_struct *work)
 
 	typec_switch_set(alt_port->typec_switch, alt_port->orientation);
 
-	if (alt_port->svid == USB_TYPEC_DP_SID)
+	if (alt_port->svid == USB_TYPEC_DP_SID && alt_port->mode == 0xff)
+		pmic_glink_altmode_safe(altmode, alt_port);
+	else if (alt_port->svid == USB_TYPEC_DP_SID)
 		pmic_glink_altmode_enable_dp(altmode, alt_port, alt_port->mode,
 					     alt_port->hpd_state, alt_port->hpd_irq);
 	else

-- 
2.34.1

[PATCH v5 2/6] qcom: pmic_glink_altmode: add retimer-switch support

[Neil Armstrong]

Some boards have a retimer/redriver between the SuperSpeed
PHY and the USB-C connector to compensates signal integrity
losses mainly due to PCB & transmission cables.

Add support for an optional retimer-switch in the USB-C
connector graph.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 drivers/soc/qcom/pmic_glink_altmode.c | 43 +++++++++++++++++++++++++++++++++++
 1 file changed, 43 insertions(+)

diff --git a/drivers/soc/qcom/pmic_glink_altmode.c b/drivers/soc/qcom/pmic_glink_altmode.c
index 007d308e2f15..41d732f5b647 100644
--- a/drivers/soc/qcom/pmic_glink_altmode.c
+++ b/drivers/soc/qcom/pmic_glink_altmode.c
@@ -15,6 +15,7 @@
 #include <linux/usb/typec_altmode.h>
 #include <linux/usb/typec_dp.h>
 #include <linux/usb/typec_mux.h>
+#include <linux/usb/typec_retimer.h>
 
 #include <linux/soc/qcom/pmic_glink.h>
 
@@ -68,6 +69,8 @@ struct pmic_glink_altmode_port {
 	struct typec_switch *typec_switch;
 	struct typec_mux *typec_mux;
 	struct typec_mux_state state;
+	struct typec_retimer *typec_retimer;
+	struct typec_retimer_state retimer_state;
 	struct typec_altmode dp_alt;
 
 	struct work_struct work;
@@ -157,6 +160,14 @@ static void pmic_glink_altmode_enable_dp(struct pmic_glink_altmode *altmode,
 	ret = typec_mux_set(port->typec_mux, &port->state);
 	if (ret)
 		dev_err(altmode->dev, "failed to switch mux to DP\n");
+
+	port->retimer_state.alt = &port->dp_alt;
+	port->retimer_state.data = &dp_data;
+	port->retimer_state.mode = TYPEC_MODAL_STATE(mode);
+
+	ret = typec_retimer_set(port->typec_retimer, &port->retimer_state);
+	if (ret)
+		dev_err(altmode->dev, "failed to setup retimer to DP\n");
 }
 
 static void pmic_glink_altmode_enable_usb(struct pmic_glink_altmode *altmode,
@@ -171,6 +182,14 @@ static void pmic_glink_altmode_enable_usb(struct pmic_glink_altmode *altmode,
 	ret = typec_mux_set(port->typec_mux, &port->state);
 	if (ret)
 		dev_err(altmode->dev, "failed to switch mux to USB\n");
+
+	port->retimer_state.alt = NULL;
+	port->retimer_state.data = NULL;
+	port->retimer_state.mode = TYPEC_STATE_USB;
+
+	ret = typec_retimer_set(port->typec_retimer, &port->retimer_state);
+	if (ret)
+		dev_err(altmode->dev, "failed to setup retimer to USB\n");
 }
 
 static void pmic_glink_altmode_safe(struct pmic_glink_altmode *altmode,
@@ -185,6 +204,14 @@ static void pmic_glink_altmode_safe(struct pmic_glink_altmode *altmode,
 	ret = typec_mux_set(port->typec_mux, &port->state);
 	if (ret)
 		dev_err(altmode->dev, "failed to switch mux to safe mode\n");
+
+	port->retimer_state.alt = NULL;
+	port->retimer_state.data = NULL;
+	port->retimer_state.mode = TYPEC_STATE_SAFE;
+
+	ret = typec_retimer_set(port->typec_retimer, &port->retimer_state);
+	if (ret)
+		dev_err(altmode->dev, "failed to setup retimer to USB\n");
 }
 
 static void pmic_glink_altmode_worker(struct work_struct *work)
@@ -347,6 +374,11 @@ static const struct drm_bridge_funcs pmic_glink_altmode_bridge_funcs = {
 	.attach = pmic_glink_altmode_attach,
 };
 
+static void pmic_glink_altmode_put_retimer(void *data)
+{
+	typec_retimer_put(data);
+}
+
 static void pmic_glink_altmode_put_mux(void *data)
 {
 	typec_mux_put(data);
@@ -453,6 +485,17 @@ static int pmic_glink_altmode_probe(struct auxiliary_device *adev,
 		if (ret)
 			return ret;
 
+		alt_port->typec_retimer = fwnode_typec_retimer_get(fwnode);
+		if (IS_ERR(alt_port->typec_retimer))
+			return dev_err_probe(dev, PTR_ERR(alt_port->typec_retimer),
+					     "failed to acquire retimer-switch for port: %d\n",
+					     port);
+
+		ret = devm_add_action_or_reset(dev, pmic_glink_altmode_put_retimer,
+					       alt_port->typec_retimer);
+		if (ret)
+			return ret;
+
 		alt_port->typec_switch = fwnode_typec_switch_get(fwnode);
 		if (IS_ERR(alt_port->typec_switch))
 			return dev_err_probe(dev, PTR_ERR(alt_port->typec_switch),

-- 
2.34.1

[PATCH v5 3/6] qcom: pmic_glink: enable altmode for SM8550

[Neil Armstrong]

Altmode is also supported for SM8550, allow it.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 drivers/soc/qcom/pmic_glink.c | 6 +-----
 1 file changed, 1 insertion(+), 5 deletions(-)

diff --git a/drivers/soc/qcom/pmic_glink.c b/drivers/soc/qcom/pmic_glink.c
index c87056769ebd..8af06bdc6f5a 100644
--- a/drivers/soc/qcom/pmic_glink.c
+++ b/drivers/soc/qcom/pmic_glink.c
@@ -342,13 +342,9 @@ static const unsigned long pmic_glink_sm8450_client_mask = BIT(PMIC_GLINK_CLIENT
 							   BIT(PMIC_GLINK_CLIENT_ALTMODE) |
 							   BIT(PMIC_GLINK_CLIENT_UCSI);
 
-/* Do not handle altmode for now on those platforms */
-static const unsigned long pmic_glink_sm8550_client_mask = BIT(PMIC_GLINK_CLIENT_BATT) |
-							   BIT(PMIC_GLINK_CLIENT_UCSI);
-
 static const struct of_device_id pmic_glink_of_match[] = {
 	{ .compatible = "qcom,sm8450-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
-	{ .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8550_client_mask },
+	{ .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
 	{ .compatible = "qcom,pmic-glink" },
 	{}
 };

-- 
2.34.1

[PATCH v5 4/6] arm64: dts: qcom: sm8550: add ports subnodes in usb/dp qmpphy node

[Neil Armstrong]

Add the USB3+DP Combo QMP PHY port subnodes in the SM8550 SoC DTSI
to avoid duplication in the devices DTs.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8550.dtsi | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 41d60af93692..54636f475306 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -2838,6 +2838,32 @@ usb_dp_qmpphy: phy@88e8000 {
 			#phy-cells = <1>;
 
 			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					usb_dp_qmpphy_out: endpoint {
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					usb_dp_qmpphy_usb_ss_in: endpoint {
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					usb_dp_qmpphy_dp_in: endpoint {
+					};
+				};
+			};
 		};
 
 		usb_1: usb@a6f8800 {

-- 
2.34.1

[PATCH v5 5/6] arm64: dts: qcom: sm8550-mtp: add pmic glink port/endpoints

[Neil Armstrong]

Add nodes to support Type-C USB/DP functionality.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 59 +++++++++++++++++++++++++++++++--
 1 file changed, 57 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
index ec86c5f38045..99375f1ceab6 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
@@ -80,7 +80,15 @@ port@1 {
 					reg = <1>;
 
 					pmic_glink_ss_in: endpoint {
-						remote-endpoint = <&usb_1_dwc3_ss>;
+						remote-endpoint = <&usb_dp_qmpphy_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_sbu: endpoint {
+						remote-endpoint = <&fsa4480_sbu_mux>;
 					};
 				};
 			};
@@ -500,6 +508,30 @@ vreg_l3g_1p2: ldo3 {
 	};
 };
 
+&i2c_master_hub_0 {
+	status = "okay";
+};
+
+&i2c_hub_2 {
+	status = "okay";
+
+	typec-mux@42 {
+		compatible = "fcs,fsa4480";
+		reg = <0x42>;
+
+		vcc-supply = <&vreg_bob1>;
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			fsa4480_sbu_mux: endpoint {
+				remote-endpoint = <&pmic_glink_sbu>;
+			};
+		};
+	};
+};
+
 &lpass_tlmm {
 	spkr_1_sd_n_active: spkr-1-sd-n-active-state {
 		pins = "gpio17";
@@ -558,6 +590,15 @@ &mdss_dsi0_phy {
 	status = "okay";
 };
 
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1>;
+	remote-endpoint = <&usb_dp_qmpphy_dp_in>;
+};
+
 &pcie_1_phy_aux_clk {
 	clock-frequency = <1000>;
 };
@@ -781,7 +822,7 @@ &usb_1_dwc3_hs {
 };
 
 &usb_1_dwc3_ss {
-	remote-endpoint = <&pmic_glink_ss_in>;
+	remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
 };
 
 &usb_1_hsphy {
@@ -797,9 +838,23 @@ &usb_dp_qmpphy {
 	vdda-phy-supply = <&vreg_l3e_1p2>;
 	vdda-pll-supply = <&vreg_l3f_0p91>;
 
+	orientation-switch;
+
 	status = "okay";
 };
 
+&usb_dp_qmpphy_dp_in {
+	remote-endpoint = <&mdss_dp0_out>;
+};
+
+&usb_dp_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss_in>;
+};
+
+&usb_dp_qmpphy_usb_ss_in {
+	remote-endpoint = <&usb_1_dwc3_ss>;
+};
+
 &xo_board {
 	clock-frequency = <76800000>;
 };

-- 
2.34.1

[PATCH v5 6/6] arm64: dts: qcom: sm8550-qrd: add pmic glink port/endpoints

[Neil Armstrong]

Add nodes to support Type-C USB/DP functionality.

On this platform, a Type-C redriver is added to the
SuperSpeed graph.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8550-qrd.dts | 91 ++++++++++++++++++++++++++++++++-
 1 file changed, 89 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
index ec4feee6837d..efcc2559b3e1 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
@@ -97,7 +97,15 @@ port@1 {
 					reg = <1>;
 
 					pmic_glink_ss_in: endpoint {
-						remote-endpoint = <&usb_1_dwc3_ss>;
+						remote-endpoint = <&redriver_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_sbu: endpoint {
+						remote-endpoint = <&fsa4480_sbu_mux>;
 					};
 				};
 			};
@@ -517,6 +525,62 @@ vreg_l3g_1p2: ldo3 {
 	};
 };
 
+&i2c_master_hub_0 {
+	status = "okay";
+};
+
+&i2c_hub_2 {
+	status = "okay";
+
+	typec-retimer@1c {
+		compatible = "onnn,nb7vpq904m";
+		reg = <0x1c>;
+
+		vcc-supply = <&vreg_l15b_1p8>;
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				redriver_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				redriver_ss_in: endpoint {
+					data-lanes = <3 2 1 0>;
+					remote-endpoint = <&usb_dp_qmpphy_out>;
+				};
+			};
+		};
+	};
+
+	typec-mux@42 {
+		compatible = "fcs,fsa4480";
+		reg = <0x42>;
+
+		vcc-supply = <&vreg_bob1>;
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			fsa4480_sbu_mux: endpoint {
+				remote-endpoint = <&pmic_glink_sbu>;
+			};
+		};
+	};
+};
+
 &gcc {
 	clocks = <&bi_tcxo_div2>, <&sleep_clk>,
 		 <&pcie0_phy>,
@@ -586,6 +650,15 @@ &mdss_dsi0_phy {
 	status = "okay";
 };
 
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1>;
+	remote-endpoint = <&usb_dp_qmpphy_dp_in>;
+};
+
 &pcie_1_phy_aux_clk {
 	status = "disabled";
 };
@@ -842,7 +915,7 @@ &usb_1_dwc3_hs {
 };
 
 &usb_1_dwc3_ss {
-	remote-endpoint = <&pmic_glink_ss_in>;
+	remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
 };
 
 &usb_1_hsphy {
@@ -858,9 +931,23 @@ &usb_dp_qmpphy {
 	vdda-phy-supply = <&vreg_l3e_1p2>;
 	vdda-pll-supply = <&vreg_l3f_0p88>;
 
+	orientation-switch;
+
 	status = "okay";
 };
 
+&usb_dp_qmpphy_dp_in {
+	remote-endpoint = <&mdss_dp0_out>;
+};
+
+&usb_dp_qmpphy_out {
+	remote-endpoint = <&redriver_ss_in>;
+};
+
+&usb_dp_qmpphy_usb_ss_in {
+	remote-endpoint = <&usb_1_dwc3_ss>;
+};
+
 &xo_board {
 	clock-frequency = <76800000>;
 };

-- 
2.34.1

Re: [PATCH v5 6/6] arm64: dts: qcom: sm8550-qrd: add pmic glink port/endpoints

[Krzysztof Kozlowski]

On 19/06/2023 10:07, Neil Armstrong wrote:
> Add nodes to support Type-C USB/DP functionality.
> 
> On this platform, a Type-C redriver is added to the
> SuperSpeed graph.
> 
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH v5 5/6] arm64: dts: qcom: sm8550-mtp: add pmic glink port/endpoints

[Krzysztof Kozlowski]

On 19/06/2023 10:07, Neil Armstrong wrote:
> Add nodes to support Type-C USB/DP functionality.
> 
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 59 +++++++++++++++++++++++++++++++--
>  1 file changed, 57 insertions(+), 2 deletions(-)


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: (subset) [PATCH v5 0/6] arm64: qcom: add Type-C Altmode support

[Bjorn Andersson]

On Mon, 19 Jun 2023 10:07:12 +0200, Neil Armstrong wrote:
> This adds the missing bits to support the USB-C Altmode
> support on SM8550.
> 
> These are the following changes since the previous SM8450 SoC:
> - No more GLINK altmode events for USB only changes, only DP
> - Type-C orientation is available on a PMIC signal connected
>   to a GPIO line
> - When altmode is disconnected, an 0xff mode event is sent.
> 
> [...]

Applied, thanks!

[4/6] arm64: dts: qcom: sm8550: add ports subnodes in usb/dp qmpphy node
      commit: 243f1a6d3df947874827a9a8837145621cbef7d3
[5/6] arm64: dts: qcom: sm8550-mtp: add pmic glink port/endpoints
      commit: 7a69845b3a08eb28dacbef35f47d979e4908e21f
[6/6] arm64: dts: qcom: sm8550-qrd: add pmic glink port/endpoints
      commit: fd42c8ec68905bfd093ce08ecf893d995d8f1478

Best regards,
-- 
Bjorn Andersson <andersson@kernel.org>