* [PATCH v3 0/3] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees
@ 2024-01-20 9:57 Raymond Hackley
2024-01-20 9:57 ` [PATCH v3 1/2] dt-bindings: qcom: Document new msm8916-samsung devices Raymond Hackley
` (3 more replies)
0 siblings, 4 replies; 6+ messages in thread
From: Raymond Hackley @ 2024-01-20 9:57 UTC (permalink / raw)
To: linux-kernel
Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Stephan Gerhold, Nikita Travkin, linux-arm-msm,
devicetree, ~postmarketos/upstreaming
Samsung Galaxy Core Prime and Grand Prime are phones based on MSM8916.
They are similar to the other Samsung devices based on MSM8916 with only a
few minor differences.
This initial commit adds support for:
- fortuna3g (SM-G530H)
- gprimeltecan (SM-G530W)
- grandprimelte (SM-G530FZ)
- rossa (SM-G360G)
The device trees contain initial support with:
- GPIO keys
- Regulator haptic
- SDHCI (internal and external storage)
- USB Device Mode
- UART (on USB connector via the SM5502/SM5504 MUIC)
- WCNSS (WiFi/BT)
- Regulators
- QDSP6 audio
- Speaker/earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- WWAN Internet via BAM-DMUX
There are different variants of Core Prime and Grand Prime, with some
differences in accelerometer, NFC and panel.
Core Prime and Grand Prime are similar, with some differences in MUIC,
panel and touchscreen.
The common parts are shared in
msm8916-samsung-fortuna-common.dtsi and msm8916-samsung-rossa-common.dtsi
to reduce duplication.
---
v3: Drop fortunaltezt and heatqlte. Add sound and modem.
/delete-node/ &muic; in rossa-common.dtsi
v2: Use interrupt-extended. Drop fuelgauge, sensors and NFC for now.
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v3 1/2] dt-bindings: qcom: Document new msm8916-samsung devices
2024-01-20 9:57 [PATCH v3 0/3] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees Raymond Hackley
@ 2024-01-20 9:57 ` Raymond Hackley
2024-01-20 9:57 ` [PATCH v3 2/2] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees Raymond Hackley
` (2 subsequent siblings)
3 siblings, 0 replies; 6+ messages in thread
From: Raymond Hackley @ 2024-01-20 9:57 UTC (permalink / raw)
To: linux-kernel
Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Stephan Gerhold, Nikita Travkin, linux-arm-msm,
devicetree, ~postmarketos/upstreaming, Rob Herring
Document the new following device tree bindings used in their
device trees:
- samsung,fortuna3g
- samsung,gprimeltecan
- samsung,grandprimelte
- samsung,rossa
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 1a5fb889a444..337053ca700b 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -244,11 +244,15 @@ properties:
- samsung,a5u-eur
- samsung,e5
- samsung,e7
+ - samsung,fortuna3g
+ - samsung,gprimeltecan
- samsung,grandmax
+ - samsung,grandprimelte
- samsung,gt510
- samsung,gt58
- samsung,j5
- samsung,j5x
+ - samsung,rossa
- samsung,serranove
- thwc,uf896
- thwc,ufi001c
--
2.39.2
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 2/2] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees
2024-01-20 9:57 [PATCH v3 0/3] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees Raymond Hackley
2024-01-20 9:57 ` [PATCH v3 1/2] dt-bindings: qcom: Document new msm8916-samsung devices Raymond Hackley
@ 2024-01-20 9:57 ` Raymond Hackley
2024-01-28 0:47 ` Bjorn Andersson
2024-01-20 10:09 ` [PATCH v3 0/3] " Raymond Hackley
2024-01-28 2:17 ` Bjorn Andersson
3 siblings, 1 reply; 6+ messages in thread
From: Raymond Hackley @ 2024-01-20 9:57 UTC (permalink / raw)
To: linux-kernel
Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Stephan Gerhold, Nikita Travkin, linux-arm-msm,
devicetree, ~postmarketos/upstreaming, Walter Broemeling,
Joe Mason, Siddharth Manthan
From: Walter Broemeling <wallebroem@gmail.com>
Samsung Galaxy Core Prime and Grand Prime are phones based on MSM8916.
They are similar to the other Samsung devices based on MSM8916 with only a
few minor differences.
This initial commit adds support for:
- fortuna3g (SM-G530H)
- gprimeltecan (SM-G530W)
- grandprimelte (SM-G530FZ)
- rossa (SM-G360G)
The device trees contain initial support with:
- GPIO keys
- Regulator haptic
- SDHCI (internal and external storage)
- USB Device Mode
- UART (on USB connector via the SM5502/SM5504 MUIC)
- WCNSS (WiFi/BT)
- Regulators
- QDSP6 audio
- Speaker/earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- WWAN Internet via BAM-DMUX
There are different variants of Core Prime and Grand Prime, with some
differences in accelerometer, NFC and panel.
Core Prime and Grand Prime are similar, with some differences in MUIC,
panel and touchscreen.
The common parts are shared in
msm8916-samsung-fortuna-common.dtsi and msm8916-samsung-rossa-common.dtsi
to reduce duplication.
Signed-off-by: Walter Broemeling <wallebroem@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
[Joe: Add audio, buttons and WiFi]
Signed-off-by: Joe Mason <buddyjojo06@outlook.com>
[Siddharth: Add fortuna3g]
Signed-off-by: Siddharth Manthan <siddharth.manthan@gmail.com>
[Raymond: Add modem, fortuna-common.dtsi, grandprimelte and rossa]
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
---
arch/arm64/boot/dts/qcom/Makefile | 4 +
.../qcom/msm8916-samsung-fortuna-common.dtsi | 170 ++++++++++++++++++
.../dts/qcom/msm8916-samsung-gprimeltecan.dts | 26 +++
.../qcom/msm8916-samsung-grandprimelte.dts | 15 ++
.../qcom/msm8916-samsung-rossa-common.dtsi | 16 ++
.../boot/dts/qcom/msm8916-samsung-rossa.dts | 15 ++
6 files changed, 246 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-fortuna-common.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-gprimeltecan.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-grandprimelte.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-rossa-common.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-rossa.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 39889d5f8e12..1abd25e19a1f 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -23,6 +23,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp433.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp449.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp453.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp454.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8216-samsung-fortuna3g.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-acer-a1-724.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb
@@ -35,11 +36,14 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a3u-eur.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a5u-eur.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-e5.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-e7.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-gprimeltecan.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-grandmax.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-grandprimelte.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-gt510.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-gt58.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-j5.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-j5x.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-rossa.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-serranove.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-uf896.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-ufi001c.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-fortuna-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-fortuna-common.dtsi
new file mode 100644
index 000000000000..f7b2586f3679
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-fortuna-common.dtsi
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "msm8916-pm8916.dtsi"
+#include "msm8916-modem-qdsp6.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ aliases {
+ mmc0 = &sdhc_1; /* eMMC */
+ mmc1 = &sdhc_2; /* SD card */
+ serial0 = &blsp_uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0";
+ };
+
+ reserved-memory {
+ /* Additional memory used by Samsung firmware modifications */
+ tz-apps@85a00000 {
+ reg = <0x0 0x85a00000 0x0 0x600000>;
+ no-map;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&gpio_keys_default>;
+ pinctrl-names = "default";
+
+ label = "GPIO Buttons";
+
+ button-volume-up {
+ label = "Volume Up";
+ gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ button-home {
+ label = "Home";
+ gpios = <&tlmm 109 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOMEPAGE>;
+ };
+ };
+
+ haptic {
+ compatible = "regulator-haptic";
+ haptic-supply = <®_motor_vdd>;
+ min-microvolt = <3300000>;
+ max-microvolt = <3300000>;
+ };
+
+ reg_motor_vdd: regulator-motor-vdd {
+ compatible = "regulator-fixed";
+ regulator-name = "motor_vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 72 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&motor_en_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&blsp_i2c1 {
+ status = "okay";
+
+ muic: extcon@25 {
+ compatible = "siliconmitus,sm5502-muic";
+ reg = <0x25>;
+ interrupts-extended = <&tlmm 12 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-0 = <&muic_int_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&blsp_uart2 {
+ status = "okay";
+};
+
+&mpss_mem {
+ reg = <0x0 0x86800000 0x0 0x5000000>;
+};
+
+&pm8916_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+ status = "okay";
+};
+
+&pm8916_rpm_regulators {
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+};
+
+&sdhc_1 {
+ status = "okay";
+};
+
+&sdhc_2 {
+ pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+ pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
+ pinctrl-names = "default", "sleep";
+
+ cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+
+ status = "okay";
+};
+
+&sound {
+ model = "msm8916-1mic";
+ audio-routing =
+ "AMIC1", "MIC BIAS External1",
+ "AMIC2", "MIC BIAS Internal2",
+ "AMIC3", "MIC BIAS External1";
+};
+
+&usb {
+ extcon = <&muic>, <&muic>;
+ status = "okay";
+};
+
+&usb_hs_phy {
+ extcon = <&muic>;
+};
+
+&wcnss {
+ status = "okay";
+};
+
+&wcnss_iris {
+ compatible = "qcom,wcn3620";
+};
+
+&tlmm {
+ gpio_keys_default: gpio-keys-default-state {
+ pins = "gpio107", "gpio109";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ motor_en_default: motor-en-default-state {
+ pins = "gpio72";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ muic_int_default: muic-int-default-state {
+ pins = "gpio12";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ sdc2_cd_default: sdc2-cd-default-state {
+ pins = "gpio38";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-gprimeltecan.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-gprimeltecan.dts
new file mode 100644
index 000000000000..022f250ea21d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-gprimeltecan.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-samsung-fortuna-common.dtsi"
+
+/ {
+ model = "Samsung Galaxy Grand Prime (SM-G530W)";
+ compatible = "samsung,gprimeltecan", "qcom,msm8916";
+ chassis-type = "handset";
+
+ reserved-memory {
+ /* Firmware for gprimeltecan needs more space */
+ /delete-node/ tz-apps@85a00000;
+
+ /* Additional memory used by Samsung firmware modifications */
+ tz-apps@85500000 {
+ reg = <0x0 0x85500000 0x0 0xb00000>;
+ no-map;
+ };
+ };
+};
+
+&mpss_mem {
+ reg = <0x0 0x86800000 0x0 0x5400000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-grandprimelte.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-grandprimelte.dts
new file mode 100644
index 000000000000..62b8359a5a85
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-grandprimelte.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-samsung-fortuna-common.dtsi"
+
+/ {
+ model = "Samsung Galaxy Grand Prime (SM-G530FZ)";
+ compatible = "samsung,grandprimelte", "qcom,msm8916";
+ chassis-type = "handset";
+};
+
+&mpss_mem {
+ reg = <0x0 0x86800000 0x0 0x5400000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-rossa-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-rossa-common.dtsi
new file mode 100644
index 000000000000..42843771ae2a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-rossa-common.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "msm8916-samsung-fortuna-common.dtsi"
+
+/* SM5504 MUIC instead of SM5502 */
+/delete-node/ &muic;
+
+&blsp_i2c1 {
+ muic: extcon@14 {
+ compatible = "siliconmitus,sm5504-muic";
+ reg = <0x14>;
+ interrupts-extended = <&tlmm 12 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-0 = <&muic_int_default>;
+ pinctrl-names = "default";
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-rossa.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-rossa.dts
new file mode 100644
index 000000000000..93e795fcee97
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-rossa.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-samsung-rossa-common.dtsi"
+
+/ {
+ model = "Samsung Galaxy Core Prime LTE";
+ compatible = "samsung,rossa", "qcom,msm8916";
+ chassis-type = "handset";
+};
+
+&mpss_mem {
+ reg = <0x0 0x86800000 0x0 0x5800000>;
+};
--
2.39.2
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v3 0/3] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees
2024-01-20 9:57 [PATCH v3 0/3] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees Raymond Hackley
2024-01-20 9:57 ` [PATCH v3 1/2] dt-bindings: qcom: Document new msm8916-samsung devices Raymond Hackley
2024-01-20 9:57 ` [PATCH v3 2/2] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees Raymond Hackley
@ 2024-01-20 10:09 ` Raymond Hackley
2024-01-28 2:17 ` Bjorn Andersson
3 siblings, 0 replies; 6+ messages in thread
From: Raymond Hackley @ 2024-01-20 10:09 UTC (permalink / raw)
To: raymondhackley
Cc: andersson, conor+dt, devicetree, konrad.dybcio,
krzysztof.kozlowski+dt, linux-arm-msm, linux-kernel, nikita,
robh+dt, stephan, ~postmarketos/upstreaming
Hi,
Sorry for confusing in the title of the cover letter. There are only
2 patches in v3.
Regards,
Raymond
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v3 2/2] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees
2024-01-20 9:57 ` [PATCH v3 2/2] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees Raymond Hackley
@ 2024-01-28 0:47 ` Bjorn Andersson
0 siblings, 0 replies; 6+ messages in thread
From: Bjorn Andersson @ 2024-01-28 0:47 UTC (permalink / raw)
To: Raymond Hackley
Cc: linux-kernel, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Stephan Gerhold, Nikita Travkin, linux-arm-msm,
devicetree, ~postmarketos/upstreaming, Walter Broemeling,
Joe Mason, Siddharth Manthan
On Sat, Jan 20, 2024 at 09:57:50AM +0000, Raymond Hackley wrote:
> From: Walter Broemeling <wallebroem@gmail.com>
> This initial commit adds support for:
> - fortuna3g (SM-G530H)
[..]
> arch/arm64/boot/dts/qcom/Makefile | 4 +
> .../qcom/msm8916-samsung-fortuna-common.dtsi | 170 ++++++++++++++++++
> .../dts/qcom/msm8916-samsung-gprimeltecan.dts | 26 +++
> .../qcom/msm8916-samsung-grandprimelte.dts | 15 ++
> .../qcom/msm8916-samsung-rossa-common.dtsi | 16 ++
> .../boot/dts/qcom/msm8916-samsung-rossa.dts | 15 ++
> 6 files changed, 246 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-fortuna-common.dtsi
> create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-gprimeltecan.dts
> create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-grandprimelte.dts
> create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-rossa-common.dtsi
> create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-rossa.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 39889d5f8e12..1abd25e19a1f 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -23,6 +23,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp433.dtb
> dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp449.dtb
> dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp453.dtb
> dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp454.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += msm8216-samsung-fortuna3g.dtb
This is missing from the patch.
Regards,
Bjorn
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v3 0/3] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees
2024-01-20 9:57 [PATCH v3 0/3] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees Raymond Hackley
` (2 preceding siblings ...)
2024-01-20 10:09 ` [PATCH v3 0/3] " Raymond Hackley
@ 2024-01-28 2:17 ` Bjorn Andersson
3 siblings, 0 replies; 6+ messages in thread
From: Bjorn Andersson @ 2024-01-28 2:17 UTC (permalink / raw)
To: linux-kernel, Raymond Hackley
Cc: Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Stephan Gerhold, Nikita Travkin, linux-arm-msm, devicetree,
~postmarketos/upstreaming
On Sat, 20 Jan 2024 09:57:27 +0000, Raymond Hackley wrote:
> Samsung Galaxy Core Prime and Grand Prime are phones based on MSM8916.
> They are similar to the other Samsung devices based on MSM8916 with only a
> few minor differences.
>
> This initial commit adds support for:
> - fortuna3g (SM-G530H)
> - gprimeltecan (SM-G530W)
> - grandprimelte (SM-G530FZ)
> - rossa (SM-G360G)
>
> [...]
Applied, thanks!
[1/2] dt-bindings: qcom: Document new msm8916-samsung devices
commit: 80daa2fa2ff2ce01550713956a6f7e18bbbd3f7f
[2/2] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees
(no commit info)
Best regards,
--
Bjorn Andersson <andersson@kernel.org>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2024-01-28 2:17 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2024-01-20 9:57 [PATCH v3 0/3] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees Raymond Hackley
2024-01-20 9:57 ` [PATCH v3 1/2] dt-bindings: qcom: Document new msm8916-samsung devices Raymond Hackley
2024-01-20 9:57 ` [PATCH v3 2/2] arm64: dts: qcom: msm8916-samsung-fortuna: Add initial device trees Raymond Hackley
2024-01-28 0:47 ` Bjorn Andersson
2024-01-20 10:09 ` [PATCH v3 0/3] " Raymond Hackley
2024-01-28 2:17 ` Bjorn Andersson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).