* [PATCH v3 0/2] spi: Add DMA support for ti-qspi
@ 2016-06-07 8:18 Vignesh R
2016-06-07 8:18 ` [PATCH v3 1/2] spi: Add DMA support for spi_flash_read() Vignesh R
2016-06-07 8:18 ` [PATCH v3 2/2] spi: spi-ti-qspi: Add DMA support for QSPI mmap read Vignesh R
0 siblings, 2 replies; 8+ messages in thread
From: Vignesh R @ 2016-06-07 8:18 UTC (permalink / raw)
To: Mark Brown; +Cc: linux-spi, linux-kernel, linux-omap, Vignesh R
This series adds support for DMA during QSPI flash read using memory
mapped mode.
Tested on DRA74 EVM, DRA72 EVM and AM437x SK on linux-next.
v2: https://lkml.org/lkml/2016/4/25/187
v1: https://lkml.org/lkml/2016/4/4/855
Vignesh R (2):
spi: Add DMA support for spi_flash_read()
spi: spi-ti-qspi: Add DMA support for QSPI mmap read
drivers/spi/spi-ti-qspi.c | 189 ++++++++++++++++++++++++++++++++++++++++++----
drivers/spi/spi.c | 14 ++++
include/linux/spi/spi.h | 4 +
3 files changed, 194 insertions(+), 13 deletions(-)
--
2.8.3
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v3 1/2] spi: Add DMA support for spi_flash_read()
2016-06-07 8:18 [PATCH v3 0/2] spi: Add DMA support for ti-qspi Vignesh R
@ 2016-06-07 8:18 ` Vignesh R
2016-06-07 22:29 ` kbuild test robot
2016-06-07 8:18 ` [PATCH v3 2/2] spi: spi-ti-qspi: Add DMA support for QSPI mmap read Vignesh R
1 sibling, 1 reply; 8+ messages in thread
From: Vignesh R @ 2016-06-07 8:18 UTC (permalink / raw)
To: Mark Brown; +Cc: linux-spi, linux-kernel, linux-omap, Vignesh R
Few SPI devices provide accelerated read interfaces to read from
SPI-NOR flash devices. These hardwares also support DMA to transfer data
from flash to memory either via mem-to-mem DMA or dedicated slave DMA
channels. Hence, add support for DMA in order to improve throughput and
reduce CPU load.
Use spi_map_buf() to get sg table for the buffer and pass it to SPI
driver.
Signed-off-by: Vignesh R <vigneshr@ti.com>
---
v3: No changes.
v2: use cur_msg_mapped flag to indicate success/failure of spi_map_buf()
drivers/spi/spi.c | 14 ++++++++++++++
include/linux/spi/spi.h | 4 ++++
2 files changed, 18 insertions(+)
diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 77e6e45951f4..da2cbe205654 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -2725,6 +2725,7 @@ int spi_flash_read(struct spi_device *spi,
{
struct spi_master *master = spi->master;
+ struct device *rx_dev = NULL;
int ret;
if ((msg->opcode_nbits == SPI_NBITS_DUAL ||
@@ -2750,9 +2751,22 @@ int spi_flash_read(struct spi_device *spi,
return ret;
}
}
+
mutex_lock(&master->bus_lock_mutex);
+ if (master->dma_rx) {
+ rx_dev = master->dma_rx->device->dev;
+ ret = spi_map_buf(master, rx_dev, &msg->rx_sg,
+ msg->buf, msg->len,
+ DMA_FROM_DEVICE);
+ if (!ret)
+ msg->cur_msg_mapped = true;
+ }
ret = master->spi_flash_read(spi, msg);
+ if (msg->cur_msg_mapped)
+ spi_unmap_buf(master, rx_dev, &msg->rx_sg,
+ DMA_FROM_DEVICE);
mutex_unlock(&master->bus_lock_mutex);
+
if (master->auto_runtime_pm)
pm_runtime_put(master->dev.parent);
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index 1f03483f61e5..7b53af4ba5f8 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -1143,6 +1143,8 @@ static inline ssize_t spi_w8r16be(struct spi_device *spi, u8 cmd)
* @opcode_nbits: number of lines to send opcode
* @addr_nbits: number of lines to send address
* @data_nbits: number of lines for data
+ * @rx_sg: Scatterlist for receive data read from flash
+ * @cur_msg_mapped: message has been mapped for DMA
*/
struct spi_flash_read_message {
void *buf;
@@ -1155,6 +1157,8 @@ struct spi_flash_read_message {
u8 opcode_nbits;
u8 addr_nbits;
u8 data_nbits;
+ struct sg_table rx_sg;
+ bool cur_msg_mapped;
};
/* SPI core interface for flash read support */
--
2.8.3
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v3 2/2] spi: spi-ti-qspi: Add DMA support for QSPI mmap read
2016-06-07 8:18 [PATCH v3 0/2] spi: Add DMA support for ti-qspi Vignesh R
2016-06-07 8:18 ` [PATCH v3 1/2] spi: Add DMA support for spi_flash_read() Vignesh R
@ 2016-06-07 8:18 ` Vignesh R
2016-06-07 9:17 ` Peter Ujfalusi
2016-06-07 10:00 ` kbuild test robot
1 sibling, 2 replies; 8+ messages in thread
From: Vignesh R @ 2016-06-07 8:18 UTC (permalink / raw)
To: Mark Brown; +Cc: linux-spi, linux-kernel, linux-omap, Vignesh R
Use mem-to-mem DMA to read from flash when reading in mmap mode. This
gives improved read performance and reduces CPU load.
With this patch the raw-read throughput is ~16MB/s on DRA74 EVM. And CPU
load is <20%. UBIFS read ~13 MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
---
v3: Cleanup code based on review comments for v2.
v2: Handle kmap'd buffers of JFFS2 FS.
drivers/spi/spi-ti-qspi.c | 189 ++++++++++++++++++++++++++++++++++++++++++----
1 file changed, 176 insertions(+), 13 deletions(-)
diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c
index 29ea8d2f9824..1f6c59c29157 100644
--- a/drivers/spi/spi-ti-qspi.c
+++ b/drivers/spi/spi-ti-qspi.c
@@ -33,6 +33,7 @@
#include <linux/pinctrl/consumer.h>
#include <linux/mfd/syscon.h>
#include <linux/regmap.h>
+#include <linux/highmem.h>
#include <linux/spi/spi.h>
@@ -41,6 +42,8 @@ struct ti_qspi_regs {
};
struct ti_qspi {
+ struct completion transfer_complete;
+
/* list synchronization */
struct mutex list_lock;
@@ -54,6 +57,9 @@ struct ti_qspi {
struct ti_qspi_regs ctx_reg;
+ dma_addr_t mmap_phys_base;
+ struct dma_chan *rx_chan;
+
u32 spi_max_frequency;
u32 cmd;
u32 dc;
@@ -379,6 +385,72 @@ static int qspi_transfer_msg(struct ti_qspi *qspi, struct spi_transfer *t,
return 0;
}
+static void ti_qspi_dma_callback(void *param)
+{
+ struct ti_qspi *qspi = param;
+
+ complete(&qspi->transfer_complete);
+}
+
+static int ti_qspi_dma_xfer(struct ti_qspi *qspi, dma_addr_t dma_dst,
+ dma_addr_t dma_src, size_t len)
+{
+ struct dma_chan *chan = qspi->rx_chan;
+ struct dma_device *dma_dev = chan->device;
+ dma_cookie_t cookie;
+ enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
+ struct dma_async_tx_descriptor *tx;
+ int ret;
+
+ tx = dma_dev->device_prep_dma_memcpy(chan, dma_dst, dma_src,
+ len, flags);
+ if (!tx) {
+ dev_err(qspi->dev, "device_prep_dma_memcpy error\n");
+ return -EIO;
+ }
+
+ tx->callback = ti_qspi_dma_callback;
+ tx->callback_param = qspi;
+ cookie = tx->tx_submit(tx);
+
+ ret = dma_submit_error(cookie);
+ if (ret) {
+ dev_err(qspi->dev, "dma_submit_error %d\n", cookie);
+ return -EIO;
+ }
+
+ dma_async_issue_pending(chan);
+ ret = wait_for_completion_timeout(&qspi->transfer_complete,
+ msecs_to_jiffies(len));
+ if (ret <= 0) {
+ dmaengine_terminate_sync(chan);
+ dev_err(qspi->dev, "DMA wait_for_completion_timeout\n");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static int ti_qspi_dma_xfer_sg(struct ti_qspi *qspi, struct sg_table rx_sg,
+ loff_t from)
+{
+ struct scatterlist *sg;
+ dma_addr_t dma_src = qspi->mmap_phys_base + from;
+ dma_addr_t dma_dst;
+ int i, len, ret;
+
+ for_each_sg(rx_sg.sgl, sg, rx_sg.nents, i) {
+ dma_dst = sg_dma_address(sg);
+ len = sg_dma_len(sg);
+ ret = ti_qspi_dma_xfer(qspi, dma_dst, dma_src, len);
+ if (ret)
+ return ret;
+ dma_src += len;
+ }
+
+ return 0;
+}
+
static void ti_qspi_enable_memory_map(struct spi_device *spi)
{
struct ti_qspi *qspi = spi_master_get_devdata(spi->master);
@@ -426,7 +498,40 @@ static void ti_qspi_setup_mmap_read(struct spi_device *spi,
QSPI_SPI_SETUP_REG(spi->chip_select));
}
-static int ti_qspi_spi_flash_read(struct spi_device *spi,
+#ifdef CONFIG_HIGHMEM
+static int ti_qspi_map_buf(struct ti_qspi *qspi, void *buf,
+ unsigned int len, struct sg_table *sgt)
+{
+ unsigned int max_seg_size =
+ dma_get_max_seg_size(qspi->rx_chan->device->dev);
+ unsigned int desc_len = min_t(int, max_seg_size, PAGE_SIZE);
+ int sgs = DIV_ROUND_UP(len + offset_in_page(buf), desc_len);
+ struct page *vm_page;
+ size_t min;
+ int i, ret;
+
+ ret = sg_alloc_table(sgt, sgs, GFP_KERNEL);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < sgs; i++) {
+ min = min_t(size_t, len, desc_len -
+ offset_in_page(buf));
+ vm_page = kmap_to_page(buf);
+ if (!vm_page) {
+ sg_free_table(sgt);
+ return -ENOMEM;
+ }
+ sg_set_page(&sgt->sgl[i], vm_page, min,
+ offset_in_page(buf));
+ buf += min;
+ len -= min;
+ }
+ return 0;
+}
+#endif
+
+static int ti_qspi_spi_flash_read(struct spi_device *spi,
struct spi_flash_read_message *msg)
{
struct ti_qspi *qspi = spi_master_get_devdata(spi->master);
@@ -437,9 +542,46 @@ static int ti_qspi_spi_flash_read(struct spi_device *spi,
if (!qspi->mmap_enabled)
ti_qspi_enable_memory_map(spi);
ti_qspi_setup_mmap_read(spi, msg);
- memcpy_fromio(msg->buf, qspi->mmap_base + msg->from, msg->len);
+
+ if (qspi->rx_chan) {
+ struct device *dev = qspi->rx_chan->device->dev;
+ void *buf = msg->buf;
+ struct sg_table sgt;
+
+ if (msg->cur_msg_mapped) {
+ ret = ti_qspi_dma_xfer_sg(qspi, msg->rx_sg, msg->from);
+ if (ret)
+ goto err_unlock;
+#ifdef CONFIG_HIGHMEM
+ } else if ((unsigned long)buf >= PKMAP_BASE &&
+ (unsigned long)buf < (PKMAP_BASE +
+ (LAST_PKMAP * PAGE_SIZE))) {
+ /* Generate sg_table for kmap buffers */
+ ret = ti_qspi_map_buf(qspi, buf, msg->len, &sgt);
+ if (ret)
+ goto err_unlock;
+ ret = dma_map_sg(dev, sgt.sgl, sgt.nents,
+ DMA_FROM_DEVICE);
+ if (!ret) {
+ ret = -ENOMEM;
+ goto err_unlock;
+ }
+ ret = ti_qspi_dma_xfer_sg(qspi, sgt, msg->from);
+ dma_unmap_sg(dev, sgt.sgl, sgt.orig_nents,
+ DMA_FROM_DEVICE);
+ sg_free_table(&sgt);
+#endif
+ } else {
+ dev_err(qspi->dev, "Invalid address for DMA\n");
+ ret = -EIO;
+ goto err_unlock;
+ }
+ } else {
+ memcpy_fromio(msg->buf, qspi->mmap_base + msg->from, msg->len);
+ }
msg->retlen = msg->len;
+err_unlock:
mutex_unlock(&qspi->list_lock);
return ret;
@@ -536,6 +678,7 @@ static int ti_qspi_probe(struct platform_device *pdev)
struct device_node *np = pdev->dev.of_node;
u32 max_freq;
int ret = 0, num_cs, irq;
+ dma_cap_mask_t mask;
master = spi_alloc_master(&pdev->dev, sizeof(*qspi));
if (!master)
@@ -550,6 +693,7 @@ static int ti_qspi_probe(struct platform_device *pdev)
master->dev.of_node = pdev->dev.of_node;
master->bits_per_word_mask = SPI_BPW_MASK(32) | SPI_BPW_MASK(16) |
SPI_BPW_MASK(8);
+ master->spi_flash_read = ti_qspi_spi_flash_read;
if (!of_property_read_u32(np, "num-cs", &num_cs))
master->num_chipselect = num_cs;
@@ -592,17 +736,6 @@ static int ti_qspi_probe(struct platform_device *pdev)
goto free_master;
}
- if (res_mmap) {
- qspi->mmap_base = devm_ioremap_resource(&pdev->dev,
- res_mmap);
- master->spi_flash_read = ti_qspi_spi_flash_read;
- if (IS_ERR(qspi->mmap_base)) {
- dev_err(&pdev->dev,
- "falling back to PIO mode\n");
- master->spi_flash_read = NULL;
- }
- }
- qspi->mmap_enabled = false;
if (of_property_read_bool(np, "syscon-chipselects")) {
qspi->ctrl_base =
@@ -637,6 +770,33 @@ static int ti_qspi_probe(struct platform_device *pdev)
if (ret)
goto free_master;
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_MEMCPY, mask);
+
+ qspi->rx_chan = dma_request_channel(mask, NULL, NULL);
+ if (!qspi->rx_chan) {
+ dev_err(qspi->dev,
+ "No Rx DMA available, trying mmap mode\n");
+ ret = 0;
+ goto no_dma;
+ }
+ master->dma_rx = qspi->rx_chan;
+ init_completion(&qspi->transfer_complete);
+ if (res_mmap)
+ qspi->mmap_phys_base = (dma_addr_t)res_mmap->start;
+
+no_dma:
+ if (!qspi->rx_chan && res_mmap) {
+ qspi->mmap_base = devm_ioremap_resource(&pdev->dev, res_mmap);
+ if (IS_ERR(qspi->mmap_base)) {
+ dev_info(&pdev->dev,
+ "mmap failed with error %ld using PIO mode\n",
+ PTR_ERR(qspi->mmap_base));
+ qspi->mmap_base = NULL;
+ master->spi_flash_read = NULL;
+ }
+ }
+ qspi->mmap_enabled = false;
return 0;
free_master:
@@ -656,6 +816,9 @@ static int ti_qspi_remove(struct platform_device *pdev)
pm_runtime_put_sync(&pdev->dev);
pm_runtime_disable(&pdev->dev);
+ if (qspi->rx_chan)
+ dma_release_channel(qspi->rx_chan);
+
return 0;
}
--
2.8.3
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v3 2/2] spi: spi-ti-qspi: Add DMA support for QSPI mmap read
2016-06-07 8:18 ` [PATCH v3 2/2] spi: spi-ti-qspi: Add DMA support for QSPI mmap read Vignesh R
@ 2016-06-07 9:17 ` Peter Ujfalusi
2016-06-08 6:53 ` Vignesh R
2016-06-07 10:00 ` kbuild test robot
1 sibling, 1 reply; 8+ messages in thread
From: Peter Ujfalusi @ 2016-06-07 9:17 UTC (permalink / raw)
To: Vignesh R, Mark Brown; +Cc: linux-spi, linux-kernel, linux-omap
On 06/07/16 11:18, Vignesh R wrote:
> Use mem-to-mem DMA to read from flash when reading in mmap mode. This
> gives improved read performance and reduces CPU load.
>
> With this patch the raw-read throughput is ~16MB/s on DRA74 EVM. And CPU
> load is <20%. UBIFS read ~13 MB/s.
>
> Signed-off-by: Vignesh R <vigneshr@ti.com>
> ---
>
> v3: Cleanup code based on review comments for v2.
> v2: Handle kmap'd buffers of JFFS2 FS.
>
> drivers/spi/spi-ti-qspi.c | 189 ++++++++++++++++++++++++++++++++++++++++++----
> 1 file changed, 176 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c
> index 29ea8d2f9824..1f6c59c29157 100644
> --- a/drivers/spi/spi-ti-qspi.c
> +++ b/drivers/spi/spi-ti-qspi.c
> @@ -33,6 +33,7 @@
> #include <linux/pinctrl/consumer.h>
> #include <linux/mfd/syscon.h>
> #include <linux/regmap.h>
> +#include <linux/highmem.h>
>
> #include <linux/spi/spi.h>
>
> @@ -41,6 +42,8 @@ struct ti_qspi_regs {
> };
>
> struct ti_qspi {
> + struct completion transfer_complete;
> +
> /* list synchronization */
> struct mutex list_lock;
>
> @@ -54,6 +57,9 @@ struct ti_qspi {
>
> struct ti_qspi_regs ctx_reg;
>
> + dma_addr_t mmap_phys_base;
> + struct dma_chan *rx_chan;
> +
> u32 spi_max_frequency;
> u32 cmd;
> u32 dc;
> @@ -379,6 +385,72 @@ static int qspi_transfer_msg(struct ti_qspi *qspi, struct spi_transfer *t,
> return 0;
> }
>
> +static void ti_qspi_dma_callback(void *param)
> +{
> + struct ti_qspi *qspi = param;
> +
> + complete(&qspi->transfer_complete);
> +}
> +
> +static int ti_qspi_dma_xfer(struct ti_qspi *qspi, dma_addr_t dma_dst,
> + dma_addr_t dma_src, size_t len)
> +{
> + struct dma_chan *chan = qspi->rx_chan;
> + struct dma_device *dma_dev = chan->device;
> + dma_cookie_t cookie;
> + enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
> + struct dma_async_tx_descriptor *tx;
> + int ret;
> +
> + tx = dma_dev->device_prep_dma_memcpy(chan, dma_dst, dma_src,
> + len, flags);
> + if (!tx) {
> + dev_err(qspi->dev, "device_prep_dma_memcpy error\n");
> + return -EIO;
> + }
> +
> + tx->callback = ti_qspi_dma_callback;
> + tx->callback_param = qspi;
> + cookie = tx->tx_submit(tx);
> +
> + ret = dma_submit_error(cookie);
> + if (ret) {
> + dev_err(qspi->dev, "dma_submit_error %d\n", cookie);
> + return -EIO;
> + }
> +
> + dma_async_issue_pending(chan);
> + ret = wait_for_completion_timeout(&qspi->transfer_complete,
> + msecs_to_jiffies(len));
> + if (ret <= 0) {
> + dmaengine_terminate_sync(chan);
> + dev_err(qspi->dev, "DMA wait_for_completion_timeout\n");
> + return -ETIMEDOUT;
> + }
> +
> + return 0;
> +}
> +
> +static int ti_qspi_dma_xfer_sg(struct ti_qspi *qspi, struct sg_table rx_sg,
> + loff_t from)
> +{
> + struct scatterlist *sg;
> + dma_addr_t dma_src = qspi->mmap_phys_base + from;
> + dma_addr_t dma_dst;
> + int i, len, ret;
> +
> + for_each_sg(rx_sg.sgl, sg, rx_sg.nents, i) {
> + dma_dst = sg_dma_address(sg);
> + len = sg_dma_len(sg);
> + ret = ti_qspi_dma_xfer(qspi, dma_dst, dma_src, len);
> + if (ret)
> + return ret;
> + dma_src += len;
> + }
> +
> + return 0;
> +}
> +
> static void ti_qspi_enable_memory_map(struct spi_device *spi)
> {
> struct ti_qspi *qspi = spi_master_get_devdata(spi->master);
> @@ -426,7 +498,40 @@ static void ti_qspi_setup_mmap_read(struct spi_device *spi,
> QSPI_SPI_SETUP_REG(spi->chip_select));
> }
>
> -static int ti_qspi_spi_flash_read(struct spi_device *spi,
> +#ifdef CONFIG_HIGHMEM
> +static int ti_qspi_map_buf(struct ti_qspi *qspi, void *buf,
> + unsigned int len, struct sg_table *sgt)
> +{
> + unsigned int max_seg_size =
> + dma_get_max_seg_size(qspi->rx_chan->device->dev);
> + unsigned int desc_len = min_t(int, max_seg_size, PAGE_SIZE);
> + int sgs = DIV_ROUND_UP(len + offset_in_page(buf), desc_len);
> + struct page *vm_page;
> + size_t min;
> + int i, ret;
> +
> + ret = sg_alloc_table(sgt, sgs, GFP_KERNEL);
> + if (ret)
> + return ret;
> +
> + for (i = 0; i < sgs; i++) {
> + min = min_t(size_t, len, desc_len -
> + offset_in_page(buf));
> + vm_page = kmap_to_page(buf);
> + if (!vm_page) {
> + sg_free_table(sgt);
> + return -ENOMEM;
> + }
> + sg_set_page(&sgt->sgl[i], vm_page, min,
> + offset_in_page(buf));
> + buf += min;
> + len -= min;
> + }
> + return 0;
> +}
> +#endif
> +
> +static int ti_qspi_spi_flash_read(struct spi_device *spi,
> struct spi_flash_read_message *msg)
> {
> struct ti_qspi *qspi = spi_master_get_devdata(spi->master);
> @@ -437,9 +542,46 @@ static int ti_qspi_spi_flash_read(struct spi_device *spi,
> if (!qspi->mmap_enabled)
> ti_qspi_enable_memory_map(spi);
> ti_qspi_setup_mmap_read(spi, msg);
> - memcpy_fromio(msg->buf, qspi->mmap_base + msg->from, msg->len);
> +
> + if (qspi->rx_chan) {
> + struct device *dev = qspi->rx_chan->device->dev;
> + void *buf = msg->buf;
> + struct sg_table sgt;
> +
> + if (msg->cur_msg_mapped) {
> + ret = ti_qspi_dma_xfer_sg(qspi, msg->rx_sg, msg->from);
> + if (ret)
> + goto err_unlock;
> +#ifdef CONFIG_HIGHMEM
> + } else if ((unsigned long)buf >= PKMAP_BASE &&
> + (unsigned long)buf < (PKMAP_BASE +
> + (LAST_PKMAP * PAGE_SIZE))) {
> + /* Generate sg_table for kmap buffers */
> + ret = ti_qspi_map_buf(qspi, buf, msg->len, &sgt);
> + if (ret)
> + goto err_unlock;
> + ret = dma_map_sg(dev, sgt.sgl, sgt.nents,
> + DMA_FROM_DEVICE);
> + if (!ret) {
> + ret = -ENOMEM;
> + goto err_unlock;
> + }
> + ret = ti_qspi_dma_xfer_sg(qspi, sgt, msg->from);
> + dma_unmap_sg(dev, sgt.sgl, sgt.orig_nents,
> + DMA_FROM_DEVICE);
> + sg_free_table(&sgt);
> +#endif
> + } else {
> + dev_err(qspi->dev, "Invalid address for DMA\n");
> + ret = -EIO;
> + goto err_unlock;
> + }
> + } else {
> + memcpy_fromio(msg->buf, qspi->mmap_base + msg->from, msg->len);
> + }
> msg->retlen = msg->len;
>
> +err_unlock:
> mutex_unlock(&qspi->list_lock);
>
> return ret;
> @@ -536,6 +678,7 @@ static int ti_qspi_probe(struct platform_device *pdev)
> struct device_node *np = pdev->dev.of_node;
> u32 max_freq;
> int ret = 0, num_cs, irq;
> + dma_cap_mask_t mask;
>
> master = spi_alloc_master(&pdev->dev, sizeof(*qspi));
> if (!master)
> @@ -550,6 +693,7 @@ static int ti_qspi_probe(struct platform_device *pdev)
> master->dev.of_node = pdev->dev.of_node;
> master->bits_per_word_mask = SPI_BPW_MASK(32) | SPI_BPW_MASK(16) |
> SPI_BPW_MASK(8);
> + master->spi_flash_read = ti_qspi_spi_flash_read;
>
> if (!of_property_read_u32(np, "num-cs", &num_cs))
> master->num_chipselect = num_cs;
> @@ -592,17 +736,6 @@ static int ti_qspi_probe(struct platform_device *pdev)
> goto free_master;
> }
>
> - if (res_mmap) {
> - qspi->mmap_base = devm_ioremap_resource(&pdev->dev,
> - res_mmap);
> - master->spi_flash_read = ti_qspi_spi_flash_read;
> - if (IS_ERR(qspi->mmap_base)) {
> - dev_err(&pdev->dev,
> - "falling back to PIO mode\n");
> - master->spi_flash_read = NULL;
> - }
> - }
> - qspi->mmap_enabled = false;
>
> if (of_property_read_bool(np, "syscon-chipselects")) {
> qspi->ctrl_base =
> @@ -637,6 +770,33 @@ static int ti_qspi_probe(struct platform_device *pdev)
> if (ret)
> goto free_master;
>
> + dma_cap_zero(mask);
> + dma_cap_set(DMA_MEMCPY, mask);
> +
> + qspi->rx_chan = dma_request_channel(mask, NULL, NULL);
dma_request_channel is deprecated, please use the:
dma_request_chan_by_mask()
> + if (!qspi->rx_chan) {
> + dev_err(qspi->dev,
> + "No Rx DMA available, trying mmap mode\n");
> + ret = 0;
> + goto no_dma;
> + }
> + master->dma_rx = qspi->rx_chan;
> + init_completion(&qspi->transfer_complete);
> + if (res_mmap)
> + qspi->mmap_phys_base = (dma_addr_t)res_mmap->start;
> +
> +no_dma:
> + if (!qspi->rx_chan && res_mmap) {
> + qspi->mmap_base = devm_ioremap_resource(&pdev->dev, res_mmap);
> + if (IS_ERR(qspi->mmap_base)) {
> + dev_info(&pdev->dev,
> + "mmap failed with error %ld using PIO mode\n",
> + PTR_ERR(qspi->mmap_base));
> + qspi->mmap_base = NULL;
> + master->spi_flash_read = NULL;
> + }
> + }
> + qspi->mmap_enabled = false;
> return 0;
>
> free_master:
> @@ -656,6 +816,9 @@ static int ti_qspi_remove(struct platform_device *pdev)
> pm_runtime_put_sync(&pdev->dev);
> pm_runtime_disable(&pdev->dev);
>
> + if (qspi->rx_chan)
> + dma_release_channel(qspi->rx_chan);
> +
> return 0;
> }
>
>
--
Péter
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v3 2/2] spi: spi-ti-qspi: Add DMA support for QSPI mmap read
2016-06-07 8:18 ` [PATCH v3 2/2] spi: spi-ti-qspi: Add DMA support for QSPI mmap read Vignesh R
2016-06-07 9:17 ` Peter Ujfalusi
@ 2016-06-07 10:00 ` kbuild test robot
1 sibling, 0 replies; 8+ messages in thread
From: kbuild test robot @ 2016-06-07 10:00 UTC (permalink / raw)
To: Vignesh R
Cc: kbuild-all, Mark Brown, linux-spi, linux-kernel, linux-omap, Vignesh R
[-- Attachment #1: Type: text/plain, Size: 1866 bytes --]
Hi,
[auto build test WARNING on spi/for-next]
[also build test WARNING on v4.7-rc2 next-20160606]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Vignesh-R/spi-Add-DMA-support-for-ti-qspi/20160607-162134
base: https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi for-next
config: mn10300-allmodconfig (attached as .config)
compiler: am33_2.0-linux-gcc (GCC) 4.9.0
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
make.cross ARCH=mn10300
All warnings (new ones prefixed by >>):
drivers/spi/spi-ti-qspi.c: In function 'ti_qspi_spi_flash_read':
>> drivers/spi/spi-ti-qspi.c:549:19: warning: unused variable 'sgt' [-Wunused-variable]
struct sg_table sgt;
^
>> drivers/spi/spi-ti-qspi.c:548:9: warning: unused variable 'buf' [-Wunused-variable]
void *buf = msg->buf;
^
>> drivers/spi/spi-ti-qspi.c:547:18: warning: unused variable 'dev' [-Wunused-variable]
struct device *dev = qspi->rx_chan->device->dev;
^
vim +/sgt +549 drivers/spi/spi-ti-qspi.c
541
542 if (!qspi->mmap_enabled)
543 ti_qspi_enable_memory_map(spi);
544 ti_qspi_setup_mmap_read(spi, msg);
545
546 if (qspi->rx_chan) {
> 547 struct device *dev = qspi->rx_chan->device->dev;
> 548 void *buf = msg->buf;
> 549 struct sg_table sgt;
550
551 if (msg->cur_msg_mapped) {
552 ret = ti_qspi_dma_xfer_sg(qspi, msg->rx_sg, msg->from);
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/octet-stream, Size: 39042 bytes --]
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v3 1/2] spi: Add DMA support for spi_flash_read()
2016-06-07 8:18 ` [PATCH v3 1/2] spi: Add DMA support for spi_flash_read() Vignesh R
@ 2016-06-07 22:29 ` kbuild test robot
2016-06-08 6:51 ` Vignesh R
0 siblings, 1 reply; 8+ messages in thread
From: kbuild test robot @ 2016-06-07 22:29 UTC (permalink / raw)
To: Vignesh R
Cc: kbuild-all, Mark Brown, linux-spi, linux-kernel, linux-omap, Vignesh R
[-- Attachment #1: Type: text/plain, Size: 1982 bytes --]
Hi,
[auto build test ERROR on spi/for-next]
[also build test ERROR on v4.7-rc2 next-20160607]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Vignesh-R/spi-Add-DMA-support-for-ti-qspi/20160607-162134
base: https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi for-next
config: m32r-allyesconfig (attached as .config)
compiler: m32r-linux-gcc (GCC) 4.9.0
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
make.cross ARCH=m32r
All errors (new ones prefixed by >>):
drivers/spi/spi.c: In function 'spi_flash_read':
>> drivers/spi/spi.c:2758:3: error: implicit declaration of function 'spi_map_buf' [-Werror=implicit-function-declaration]
ret = spi_map_buf(master, rx_dev, &msg->rx_sg,
^
>> drivers/spi/spi.c:2766:3: error: implicit declaration of function 'spi_unmap_buf' [-Werror=implicit-function-declaration]
spi_unmap_buf(master, rx_dev, &msg->rx_sg,
^
cc1: some warnings being treated as errors
vim +/spi_map_buf +2758 drivers/spi/spi.c
2752 }
2753 }
2754
2755 mutex_lock(&master->bus_lock_mutex);
2756 if (master->dma_rx) {
2757 rx_dev = master->dma_rx->device->dev;
> 2758 ret = spi_map_buf(master, rx_dev, &msg->rx_sg,
2759 msg->buf, msg->len,
2760 DMA_FROM_DEVICE);
2761 if (!ret)
2762 msg->cur_msg_mapped = true;
2763 }
2764 ret = master->spi_flash_read(spi, msg);
2765 if (msg->cur_msg_mapped)
> 2766 spi_unmap_buf(master, rx_dev, &msg->rx_sg,
2767 DMA_FROM_DEVICE);
2768 mutex_unlock(&master->bus_lock_mutex);
2769
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/octet-stream, Size: 35831 bytes --]
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v3 1/2] spi: Add DMA support for spi_flash_read()
2016-06-07 22:29 ` kbuild test robot
@ 2016-06-08 6:51 ` Vignesh R
0 siblings, 0 replies; 8+ messages in thread
From: Vignesh R @ 2016-06-08 6:51 UTC (permalink / raw)
To: Mark Brown; +Cc: linux-spi, linux-kernel, linux-omap
On Wednesday 08 June 2016 03:59 AM, kbuild test robot wrote:
> Hi,
>
> [auto build test ERROR on spi/for-next]
> [also build test ERROR on v4.7-rc2 next-20160607]
> [if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
>
> url: https://github.com/0day-ci/linux/commits/Vignesh-R/spi-Add-DMA-support-for-ti-qspi/20160607-162134
> base: https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi for-next
> config: m32r-allyesconfig (attached as .config)
> compiler: m32r-linux-gcc (GCC) 4.9.0
> reproduce:
> wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
> chmod +x ~/bin/make.cross
> # save the attached .config to linux build tree
> make.cross ARCH=m32r
>
> All errors (new ones prefixed by >>):
>
> drivers/spi/spi.c: In function 'spi_flash_read':
>>> drivers/spi/spi.c:2758:3: error: implicit declaration of function 'spi_map_buf' [-Werror=implicit-function-declaration]
> ret = spi_map_buf(master, rx_dev, &msg->rx_sg,
> ^
>>> drivers/spi/spi.c:2766:3: error: implicit declaration of function 'spi_unmap_buf' [-Werror=implicit-function-declaration]
> spi_unmap_buf(master, rx_dev, &msg->rx_sg,
> ^
> cc1: some warnings being treated as errors
>
Oops, posted v4 fixing these errors.
--
Regards
Vignesh
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v3 2/2] spi: spi-ti-qspi: Add DMA support for QSPI mmap read
2016-06-07 9:17 ` Peter Ujfalusi
@ 2016-06-08 6:53 ` Vignesh R
0 siblings, 0 replies; 8+ messages in thread
From: Vignesh R @ 2016-06-08 6:53 UTC (permalink / raw)
To: Peter Ujfalusi, Mark Brown; +Cc: linux-spi, linux-kernel, linux-omap
On Tuesday 07 June 2016 02:47 PM, Peter Ujfalusi wrote:
[...]
>> @@ -637,6 +770,33 @@ static int ti_qspi_probe(struct platform_device *pdev)
>> if (ret)
>> goto free_master;
>>
>> + dma_cap_zero(mask);
>> + dma_cap_set(DMA_MEMCPY, mask);
>> +
>> + qspi->rx_chan = dma_request_channel(mask, NULL, NULL);
>
> dma_request_channel is deprecated, please use the:
> dma_request_chan_by_mask()
>
Updated to use dma_request_chan_by_mask() in v4, Thanks.
--
Regards
Vignesh
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2016-06-08 6:53 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-06-07 8:18 [PATCH v3 0/2] spi: Add DMA support for ti-qspi Vignesh R
2016-06-07 8:18 ` [PATCH v3 1/2] spi: Add DMA support for spi_flash_read() Vignesh R
2016-06-07 22:29 ` kbuild test robot
2016-06-08 6:51 ` Vignesh R
2016-06-07 8:18 ` [PATCH v3 2/2] spi: spi-ti-qspi: Add DMA support for QSPI mmap read Vignesh R
2016-06-07 9:17 ` Peter Ujfalusi
2016-06-08 6:53 ` Vignesh R
2016-06-07 10:00 ` kbuild test robot
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).