* [PATCH] make Xircom cardbus modems work
@ 2001-05-09 13:37 Bill Nottingham
2001-05-09 13:48 ` Jeff Garzik
0 siblings, 1 reply; 5+ messages in thread
From: Bill Nottingham @ 2001-05-09 13:37 UTC (permalink / raw)
To: linux-kernel; +Cc: tytso, jgarzik
[-- Attachment #1: Type: text/plain, Size: 433 bytes --]
The attached allows serial.c to work with my Xircom cardbus
ethernet+modem combo card. It doesn't get autodetected, because
the serial driver explicitly doesn't recognize anything with
more than one iomem region (the Xircom modem has two.)
If the serial driver is linked in statically, the delay
on initialization is needed, else the UART will get detected
as a 16450 or not at all; I guess the card is just slow in
coming up.
Bill
[-- Attachment #2: linux-2.4.3-xircom_serial.patch --]
[-- Type: text/plain, Size: 825 bytes --]
--- linux/drivers/char/serial.c.foo Tue May 8 23:44:41 2001
+++ linux/drivers/char/serial.c Wed May 9 01:18:07 2001
@@ -4182,6 +4182,15 @@
return 0;
}
+static int
+#ifndef MODULE
+__devinit
+#endif
+pci_xircom_fn(struct pci_dev *dev, struct pci_board *board, int enable)
+{
+ __set_current_state(TASK_UNINTERRUPTIBLE);
+ schedule_timeout(HZ/10);
+}
/*
* This is the configuration table for all of the PCI serial boards
@@ -4558,6 +4567,11 @@
/*
* Untested PCI modems, sent in from various folks...
*/
+ /* Xircom Cardbus Ethernet 10/100 + 56k Modem <notting@redhat.com> */
+ { 0x115d, 0x0103,
+ PCI_ANY_ID, PCI_ANY_ID,
+ SPCI_FL_BASE0, 1, 115200,
+ 0, 0, pci_xircom_fn },
/* Elsa Model 56K PCI Modem, from Andreas Rath <arh@01019freenet.de> */
{ PCI_VENDOR_ID_ROCKWELL, 0x1004,
0x1048, 0x1500,
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH] make Xircom cardbus modems work
2001-05-09 13:37 [PATCH] make Xircom cardbus modems work Bill Nottingham
@ 2001-05-09 13:48 ` Jeff Garzik
2001-05-09 14:37 ` Tom Sightler
2001-05-09 21:29 ` Bill Nottingham
0 siblings, 2 replies; 5+ messages in thread
From: Jeff Garzik @ 2001-05-09 13:48 UTC (permalink / raw)
To: Bill Nottingham; +Cc: linux-kernel, tytso, Alessandro Suardi, Tom Sightler
[-- Attachment #1: Type: text/plain, Size: 929 bytes --]
Bill,
Does the attached patch work for you?
serial.c still has the basic problem that there is a logical disconnect
between the pci_boards list and the pci-device-id list: any device
which is not PCI_CLASS_COMMUNICATION_SERIAL or
PCI_CLASS_COMMUNICATION_MODEM will not get scanned. The solution is to
move the PCI ids into the probe list, before the class listing. Ideally
I would like to merge the Xircom cardbus fix with this fix, since they
are both modifying the pci_board list and thus conflict.
Except for the Xircom Cardbus update (based on your patch, Bill), this
patch has been tested and is known to solve the problems reported to me
which were caused by the logical disconnect.
(Alessandro, Tom, tytso: the attached patch is updated for the changes
in Bill's patch, so you haven't seen this version yet)
Jeff
--
Jeff Garzik | Game called on account of naked chick
Building 1024 |
MandrakeSoft |
[-- Attachment #2: serial.patch --]
[-- Type: text/plain, Size: 37327 bytes --]
Index: linux_2_4/drivers/char/serial.c
diff -u linux_2_4/drivers/char/serial.c:1.1.1.45 linux_2_4/drivers/char/serial.c:1.1.1.45.30.5
--- linux_2_4/drivers/char/serial.c:1.1.1.45 Fri Apr 13 18:31:51 2001
+++ linux_2_4/drivers/char/serial.c Wed May 9 06:44:05 2001
@@ -59,8 +59,8 @@
*
*/
-static char *serial_version = "5.05a";
-static char *serial_revdate = "2001-03-20";
+static char *serial_version = "5.05b";
+static char *serial_revdate = "2001-05-09";
/*
* Serial driver configuration section. Here are the various options:
@@ -3912,14 +3912,14 @@
if (PREPARE_FUNC(dev) && (PREPARE_FUNC(dev))(dev) < 0) {
printk("serial: PNP device '");
- printk_pnp_dev_id(board->vendor, board->device);
+ printk_pnp_dev_id(dev->vendor, dev->device);
printk("' prepare failed\n");
return;
}
if (ACTIVATE_FUNC(dev) && (ACTIVATE_FUNC(dev))(dev) < 0) {
printk("serial: PNP device '");
- printk_pnp_dev_id(board->vendor, board->device);
+ printk_pnp_dev_id(dev->vendor, dev->device);
printk("' activate failed\n");
return;
}
@@ -4107,7 +4107,7 @@
{
unsigned long oldval;
- if (!(board->subdevice & 0x1000))
+ if (!(pci_get_subvendor(dev) & 0x1000))
return(-1);
if (!enable) /* is there something to deinit? */
@@ -4182,530 +4182,660 @@
return 0;
}
+static int
+#ifndef MODULE
+__devinit
+#endif
+pci_xircom_fn(struct pci_dev *dev, struct pci_board *board, int enable)
+{
+ __set_current_state(TASK_UNINTERRUPTIBLE);
+ schedule_timeout(HZ/10);
+}
/*
* This is the configuration table for all of the PCI serial boards
- * which we support.
- */
+ * which we support. It is directly indexed by the pci_board_num_t enum
+ * value, which is encoded in the pci_device_id PCI probe table's
+ * driver_data member.
+ */
+enum pci_board_num_t {
+ pbn_b0_1_115200,
+ pbn_default = 0,
+
+ pbn_b0_2_115200,
+ pbn_b0_4_115200,
+
+ pbn_b0_1_921600,
+ pbn_b0_2_921600,
+ pbn_b0_4_921600,
+
+ pbn_b0_bt_1_115200,
+ pbn_b0_bt_2_115200,
+ pbn_b0_bt_1_460800,
+ pbn_b0_bt_2_460800,
+
+ pbn_b1_1_115200,
+ pbn_b1_2_115200,
+ pbn_b1_4_115200,
+ pbn_b1_8_115200,
+
+ pbn_b1_2_921600,
+ pbn_b1_4_921600,
+ pbn_b1_8_921600,
+
+ pbn_b1_2_1382400,
+ pbn_b1_4_1382400,
+ pbn_b1_8_1382400,
+
+ pbn_b2_8_115200,
+ pbn_b2_4_460800,
+ pbn_b2_8_460800,
+ pbn_b2_16_460800,
+ pbn_b2_4_921600,
+ pbn_b2_8_921600,
+
+ pbn_b2_bt_1_115200,
+ pbn_b2_bt_2_115200,
+ pbn_b2_bt_4_115200,
+ pbn_b2_bt_2_921600,
+
+ pbn_panacom,
+ pbn_panacom2,
+ pbn_panacom4,
+ pbn_plx_romulus,
+ pbn_oxsemi,
+ pbn_timedia,
+ pbn_intel_i960,
+ pbn_sgi_ioc3,
+#ifdef CONFIG_DDB5074
+ pbn_nec_nile4,
+#endif
+#if 0
+ pbn_dci_pccom8,
+#endif
+ pbn_xircom_combo,
+
+ pbn_siig10x_0,
+ pbn_siig10x_1,
+ pbn_siig10x_2,
+ pbn_siig10x_4,
+ pbn_siig20x_0,
+ pbn_siig20x_2,
+ pbn_siig20x_4,
+
+ pbn_computone_4,
+ pbn_computone_6,
+ pbn_computone_8,
+};
+
static struct pci_board pci_boards[] __devinitdata = {
/*
- * Vendor ID, Device ID,
- * Subvendor ID, Subdevice ID,
* PCI Flags, Number of Ports, Base (Maximum) Baud Rate,
* Offset to get to next UART's registers,
* Register shift to use for memory-mapped I/O,
* Initialization function, first UART offset
*/
+
+ /* Generic serial board, pbn_b0_1_115200, pbn_default */
+ { SPCI_FL_BASE0, 1, 115200 }, /* pbn_b0_1_115200,
+ pbn_default */
+
+ { SPCI_FL_BASE0, 2, 115200 }, /* pbn_b0_2_115200 */
+ { SPCI_FL_BASE0, 4, 115200 }, /* pbn_b0_4_115200 */
+
+ { SPCI_FL_BASE0, 1, 921600 }, /* pbn_b0_1_921600 */
+ { SPCI_FL_BASE0, 2, 921600 }, /* pbn_b0_2_921600 */
+ { SPCI_FL_BASE0, 4, 921600 }, /* pbn_b0_4_921600 */
+
+ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 }, /* pbn_b0_bt_1_115200 */
+ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200 }, /* pbn_b0_bt_2_115200 */
+ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 460800 }, /* pbn_b0_bt_1_460800 */
+ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 460800 }, /* pbn_b0_bt_2_460800 */
+
+ { SPCI_FL_BASE1, 1, 115200 }, /* pbn_b1_1_115200 */
+ { SPCI_FL_BASE1, 2, 115200 }, /* pbn_b1_2_115200 */
+ { SPCI_FL_BASE1, 4, 115200 }, /* pbn_b1_4_115200 */
+ { SPCI_FL_BASE1, 8, 115200 }, /* pbn_b1_8_115200 */
+
+ { SPCI_FL_BASE1, 2, 921600 }, /* pbn_b1_2_921600 */
+ { SPCI_FL_BASE1, 4, 921600 }, /* pbn_b1_4_921600 */
+ { SPCI_FL_BASE1, 8, 921600 }, /* pbn_b1_8_921600 */
+
+ { SPCI_FL_BASE1, 2, 1382400 }, /* pbn_b1_2_1382400 */
+ { SPCI_FL_BASE1, 4, 1382400 }, /* pbn_b1_4_1382400 */
+ { SPCI_FL_BASE1, 8, 1382400 }, /* pbn_b1_8_1382400 */
+
+ { SPCI_FL_BASE2, 8, 115200 }, /* pbn_b2_8_115200 */
+ { SPCI_FL_BASE2, 4, 460800 }, /* pbn_b2_4_460800 */
+ { SPCI_FL_BASE2, 8, 460800 }, /* pbn_b2_8_460800 */
+ { SPCI_FL_BASE2, 16, 460800 }, /* pbn_b2_16_460800 */
+ { SPCI_FL_BASE2, 4, 921600 }, /* pbn_b2_4_921600 */
+ { SPCI_FL_BASE2, 8, 921600 }, /* pbn_b2_8_921600 */
+
+ { SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 1, 115200 }, /* pbn_b2_bt_1_115200 */
+ { SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 115200 }, /* pbn_b2_bt_2_115200 */
+ { SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 4, 115200 }, /* pbn_b2_bt_4_115200 */
+ { SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 921600 }, /* pbn_b2_bt_2_921600 */
+
+ { SPCI_FL_BASE2, 2, 921600, /* IOMEM */ /* pbn_panacom */
+ 0x400, 7, pci_plx9050_fn },
+ { SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 921600, /* pbn_panacom2 */
+ 0x400, 7, pci_plx9050_fn },
+ { SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 4, 921600, /* pbn_panacom4 */
+ 0x400, 7, pci_plx9050_fn },
+ { SPCI_FL_BASE2, 4, 921600, /* pbn_plx_romulus */
+ 0x20, 2, pci_plx9050_fn, 0x03 },
+ /* This board uses the size of PCI Base region 0 to
+ * signal now many ports are available */
+ { SPCI_FL_BASE0 | SPCI_FL_REGION_SZ_CAP, 32, 115200 }, /* pbn_oxsemi */
+ { SPCI_FL_BASE_TABLE, 1, 921600, /* pbn_timedia */
+ 0, 0, pci_timedia_fn },
+ /* EKF addition for i960 Boards form EKF with serial port */
+ { SPCI_FL_BASE0, 32, 921600, /* max 256 ports */ /* pbn_intel_i960 */
+ 8<<2, 2, pci_inteli960ni_fn, 0x10000},
+ { SPCI_FL_BASE0 | SPCI_FL_IRQRESOURCE, /* pbn_sgi_ioc3 */
+ 1, 458333, 0, 0, 0, 0x20178 },
+#ifdef CONFIG_DDB5074
+ /*
+ * NEC Vrc-5074 (Nile 4) builtin UART.
+ * Conditionally compiled in since this is a motherboard device.
+ */
+ { SPCI_FL_BASE0, 1, 520833, /* pbn_nec_nile4 */
+ 64, 3, NULL, 0x300 },
+#endif
+#if 0 /* PCI_DEVICE_ID_DCI_PCCOM8 ? */ /* pbn_dci_pccom8 */
+ { SPCI_FL_BASE3, 8, 115200, 8 },
+#endif
+ { SPCI_FL_BASE0, 1, 115200, /* pbn_xircom_combo */
+ 0, 0, pci_xircom_fn },
+
+ { SPCI_FL_BASE2, 1, 460800, /* pbn_siig10x_0 */
+ 0, 0, pci_siig10x_fn },
+ { SPCI_FL_BASE2, 1, 921600, /* pbn_siig10x_1 */
+ 0, 0, pci_siig10x_fn },
+ { SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 921600, /* pbn_siig10x_2 */
+ 0, 0, pci_siig10x_fn },
+ { SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 4, 921600, /* pbn_siig10x_4 */
+ 0, 0, pci_siig10x_fn },
+ { SPCI_FL_BASE0, 1, 921600, /* pbn_siix20x_0 */
+ 0, 0, pci_siig20x_fn },
+ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 921600, /* pbn_siix20x_2 */
+ 0, 0, pci_siig20x_fn },
+ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 4, 921600, /* pbn_siix20x_4 */
+ 0, 0, pci_siig20x_fn },
+
+ { SPCI_FL_BASE0, 4, 921600, /* IOMEM */ /* pbn_computone_4 */
+ 0x40, 2, NULL, 0x200 },
+ { SPCI_FL_BASE0, 6, 921600, /* IOMEM */ /* pbn_computone_6 */
+ 0x40, 2, NULL, 0x200 },
+ { SPCI_FL_BASE0, 8, 921600, /* IOMEM */ /* pbn_computone_8 */
+ 0x40, 2, NULL, 0x200 },
+};
+
+/*
+ * Given a complete unknown PCI device, try to use some heuristics to
+ * guess what the configuration might be, based on the pitiful PCI
+ * serial specs. Returns 0 on success, 1 on failure.
+ */
+static int __devinit serial_pci_guess_board(struct pci_dev *dev,
+ struct pci_board *board)
+{
+ int num_iomem = 0, num_port = 0, first_port = -1;
+ int i;
+
+ /*
+ * If it is not a communications device or the programming
+ * interface is greater than 6, give up.
+ *
+ * (Should we try to make guesses for multiport serial devices
+ * later?)
+ */
+ if ((((dev->class >> 8) != PCI_CLASS_COMMUNICATION_SERIAL) &&
+ ((dev->class >> 8) != PCI_CLASS_COMMUNICATION_MODEM)) ||
+ (dev->class & 0xff) > 6)
+ return 1;
+
+ for (i=0; i < 6; i++) {
+ if (IS_PCI_REGION_IOPORT(dev, i)) {
+ num_port++;
+ if (first_port == -1)
+ first_port = i;
+ }
+ if (IS_PCI_REGION_IOMEM(dev, i))
+ num_iomem++;
+ }
+
+ /*
+ * If there is 1 or 0 iomem regions, and exactly one port, use
+ * it.
+ */
+ if (num_iomem <= 1 && num_port == 1) {
+ board->flags = first_port;
+ return 0;
+ }
+ return 1;
+}
+
+static int __devinit serial_init_one(struct pci_dev *dev,
+ const struct pci_device_id *ent)
+{
+ struct pci_board *board, tmp;
+ int rc;
+
+ board = &pci_boards[ent->driver_data];
+
+ rc = pci_enable_device(dev);
+ if (rc) return rc;
+
+ if (ent->driver_data == pbn_default &&
+ serial_pci_guess_board(dev, board))
+ return -ENODEV;
+ else if (serial_pci_guess_board(dev, &tmp) == 0) {
+ printk(KERN_INFO "Redundant entry in serial pci_table. "
+ "Please send the output of\n"
+ "lspci -vv, this message (%d,%d,%d,%d)\n"
+ "and the manufacturer and name of "
+ "serial board or modem board\n"
+ "to serial-pci-info@lists.sourceforge.net.\n",
+ dev->vendor, dev->device,
+ pci_get_subvendor(dev), pci_get_subdevice(dev));
+ }
+
+ start_pci_pnp_board(dev, board);
+
+ return 0;
+}
+
+static void __devexit serial_remove_one(struct pci_dev *dev)
+{
+ int i;
+
+ /*
+ * Iterate through all of the ports finding those that belong
+ * to this PCI device.
+ */
+ for(i = 0; i < NR_PORTS; i++) {
+ if (rs_table[i].dev != dev)
+ continue;
+ unregister_serial(i);
+ rs_table[i].dev = 0;
+ }
+ /*
+ * Now execute any board-specific shutdown procedure
+ */
+ for (i=0; i < NR_PCI_BOARDS; i++) {
+ struct pci_board_inst *brd = &serial_pci_board[i];
+
+ if (serial_pci_board[i].dev != dev)
+ continue;
+ if (brd->board.init_fn)
+ (brd->board.init_fn)(brd->dev, &brd->board, 0);
+ if (DEACTIVATE_FUNC(brd->dev))
+ (DEACTIVATE_FUNC(brd->dev))(brd->dev);
+ serial_pci_board[i].dev = 0;
+ }
+}
+
+
+static struct pci_device_id serial_pci_tbl[] __devinitdata = {
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232,
- SPCI_FL_BASE1, 8, 1382400 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232, 0, 0,
+ pbn_b1_8_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_232,
- SPCI_FL_BASE1, 4, 1382400 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_232, 0, 0,
+ pbn_b1_4_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_232,
- SPCI_FL_BASE1, 2, 1382400 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_232, 0, 0,
+ pbn_b1_2_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232,
- SPCI_FL_BASE1, 8, 1382400 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232, 0, 0,
+ pbn_b1_8_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_232,
- SPCI_FL_BASE1, 4, 1382400 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_232, 0, 0,
+ pbn_b1_4_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_232,
- SPCI_FL_BASE1, 2, 1382400 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_232, 0, 0,
+ pbn_b1_2_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485,
- SPCI_FL_BASE1, 8, 921600 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485, 0, 0,
+ pbn_b1_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485_4_4,
- SPCI_FL_BASE1, 8, 921600 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485_4_4, 0, 0,
+ pbn_b1_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485,
- SPCI_FL_BASE1, 4, 921600 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485, 0, 0,
+ pbn_b1_4_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485_2_2,
- SPCI_FL_BASE1, 4, 921600 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485_2_2, 0, 0,
+ pbn_b1_4_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_485,
- SPCI_FL_BASE1, 2, 921600 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_485, 0, 0,
+ pbn_b1_2_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485_2_6,
- SPCI_FL_BASE1, 8, 921600 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485_2_6, 0, 0,
+ pbn_b1_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH081101V1,
- SPCI_FL_BASE1, 8, 921600 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH081101V1, 0, 0,
+ pbn_b1_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH041101V1,
- SPCI_FL_BASE1, 4, 921600 },
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH041101V1, 0, 0,
+ pbn_b1_4_921600 },
+
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_U530,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 1, 115200 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_bt_1_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM2,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 115200 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_bt_2_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM422,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 4, 115200 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_bt_4_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM232,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 115200 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_bt_2_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_COMM4,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 4, 115200 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_bt_4_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_COMM8,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2, 8, 115200 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_8_115200 },
+
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_GTEK_SERIAL2,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 115200 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_bt_2_115200 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_SPCOM200,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 921600 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_bt_2_921600 },
/* VScom SPCOM800, from sl@s.pl */
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_SPCOM800,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2, 8, 921600 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_8_921600 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_1077,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2, 4, 921600 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_4_921600 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_KEYSPAN,
- PCI_SUBDEVICE_ID_KEYSPAN_SX2,
- SPCI_FL_BASE2, 2, 921600, /* IOMEM */
- 0x400, 7, pci_plx9050_fn },
+ PCI_SUBDEVICE_ID_KEYSPAN_SX2, 0, 0,
+ pbn_panacom },
{ PCI_VENDOR_ID_PANACOM, PCI_DEVICE_ID_PANACOM_QUADMODEM,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 4, 921600,
- 0x400, 7, pci_plx9050_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_panacom4 },
{ PCI_VENDOR_ID_PANACOM, PCI_DEVICE_ID_PANACOM_DUALMODEM,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 921600,
- 0x400, 7, pci_plx9050_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_panacom2 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
- PCI_SUBDEVICE_ID_CHASE_PCIFAST4,
- SPCI_FL_BASE2, 4, 460800 },
+ PCI_SUBDEVICE_ID_CHASE_PCIFAST4, 0, 0,
+ pbn_b2_4_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
- PCI_SUBDEVICE_ID_CHASE_PCIFAST8,
- SPCI_FL_BASE2, 8, 460800 },
+ PCI_SUBDEVICE_ID_CHASE_PCIFAST8, 0, 0,
+ pbn_b2_8_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
- PCI_SUBDEVICE_ID_CHASE_PCIFAST16,
- SPCI_FL_BASE2, 16, 460800 },
+ PCI_SUBDEVICE_ID_CHASE_PCIFAST16, 0, 0,
+ pbn_b2_16_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
- PCI_SUBDEVICE_ID_CHASE_PCIFAST16FMC,
- SPCI_FL_BASE2, 16, 460800 },
+ PCI_SUBDEVICE_ID_CHASE_PCIFAST16FMC, 0, 0,
+ pbn_b2_16_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIRAS,
- PCI_SUBDEVICE_ID_CHASE_PCIRAS4,
- SPCI_FL_BASE2, 4, 460800 },
+ PCI_SUBDEVICE_ID_CHASE_PCIRAS4, 0, 0,
+ pbn_b2_4_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIRAS,
- PCI_SUBDEVICE_ID_CHASE_PCIRAS8,
- SPCI_FL_BASE2, 8, 460800 },
+ PCI_SUBDEVICE_ID_CHASE_PCIRAS8, 0, 0,
+ pbn_b2_8_460800 },
/* Megawolf Romulus PCI Serial Card, from Mike Hudson */
/* (Exoray@isys.ca) */
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_ROMULUS,
- 0x10b5, 0x106a,
- SPCI_FL_BASE2, 4, 921600,
- 0x20, 2, pci_plx9050_fn, 0x03 },
+ 0x10b5, 0x106a, 0, 0,
+ pbn_plx_romulus },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_QSC100,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE1, 4, 115200 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_4_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_DSC100,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE1, 2, 115200 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_2_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_ESC100D,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE1, 8, 115200 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_8_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_ESC100M,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE1, 8, 115200 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_8_115200 },
{ PCI_VENDOR_ID_SPECIALIX, PCI_DEVICE_ID_OXSEMI_16PCI954,
- PCI_VENDOR_ID_SPECIALIX, PCI_SUBDEVICE_ID_SPECIALIX_SPEED4,
- SPCI_FL_BASE0 , 4, 921600 },
+ PCI_VENDOR_ID_SPECIALIX, PCI_SUBDEVICE_ID_SPECIALIX_SPEED4, 0, 0,
+ pbn_b0_4_921600 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 , 4, 115200 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_4_115200 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI952,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 , 2, 115200 },
- /* This board uses the size of PCI Base region 0 to
- * signal now many ports are available */
- { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI95N,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_REGION_SZ_CAP, 32, 115200 },
- { PCI_VENDOR_ID_TIMEDIA, PCI_DEVICE_ID_TIMEDIA_1889,
- PCI_VENDOR_ID_TIMEDIA, PCI_ANY_ID,
- SPCI_FL_BASE_TABLE, 1, 921600,
- 0, 0, pci_timedia_fn },
- { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DSERIAL,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200 },
- { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUATRO_A,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200 },
- { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUATRO_B,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200 },
- { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PORT_PLUS,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 460800 },
- { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUAD_A,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 460800 },
- { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUAD_B,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 460800 },
- { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_SSERIAL,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
- { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PORT_650,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 460800 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_2_115200 },
+
+ /* Digitan DS560-558, from jimd@esoft.com */
+ { PCI_VENDOR_ID_ATT, PCI_DEVICE_ID_ATT_VENUS_MODEM,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_1_115200 },
+
+ /* 3Com US Robotics 56k Voice Internal PCI model 5610 */
+ { PCI_VENDOR_ID_USR, 0x1008,
+ PCI_ANY_ID, PCI_ANY_ID, },
+
+ /* Titan Electronic cards */
+ { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_100,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_1_921600 },
+ { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_200,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_2_921600 },
+ { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_400,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_4_921600 },
+ { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_800B,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_4_921600 },
+
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_10x_550,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2, 1, 460800,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_0 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_10x_650,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2, 1, 460800,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_0 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_10x_850,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2, 1, 460800,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_0 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S1P_10x_550,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2, 1, 921600,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_1 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S1P_10x_650,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2, 1, 921600,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_1 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S1P_10x_850,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2, 1, 921600,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_1 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_10x_550,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 921600,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_2 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_10x_650,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 921600,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_2 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_10x_850,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 921600,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_2 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S1P_10x_550,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 921600,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_2 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S1P_10x_650,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 921600,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_2 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S1P_10x_850,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 921600,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_2 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_10x_550,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 4, 921600,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_4 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_10x_650,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 4, 921600,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_4 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_10x_850,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 4, 921600,
- 0, 0, pci_siig10x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig10x_4 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_20x_550,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 1, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_0 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_20x_650,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 1, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_0 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_20x_850,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 1, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_0 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S1P_20x_550,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 1, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_0 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S1P_20x_650,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 1, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_0 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S1P_20x_850,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 1, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_0 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P1S_20x_550,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 1, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_0 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P1S_20x_650,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 1, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_0 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P1S_20x_850,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 1, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_0 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_20x_550,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_2 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_20x_650,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_2 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_20x_850,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_2 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S1P_20x_550,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_2 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S1P_20x_650,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_2 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S1P_20x_850,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_2 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_20x_550,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 4, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_4 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_20x_650,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 4, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_4 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_20x_850,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 4, 921600,
- 0, 0, pci_siig20x_fn },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_siig20x_4 },
+
/* Computone devices submitted by Doug McNash dmcnash@computone.com */
{ PCI_VENDOR_ID_COMPUTONE, PCI_DEVICE_ID_COMPUTONE_PG,
PCI_SUBVENDOR_ID_COMPUTONE, PCI_SUBDEVICE_ID_COMPUTONE_PG4,
- SPCI_FL_BASE0, 4, 921600, /* IOMEM */
- 0x40, 2, NULL, 0x200 },
+ 0, 0, pbn_computone_4 },
{ PCI_VENDOR_ID_COMPUTONE, PCI_DEVICE_ID_COMPUTONE_PG,
PCI_SUBVENDOR_ID_COMPUTONE, PCI_SUBDEVICE_ID_COMPUTONE_PG8,
- SPCI_FL_BASE0, 8, 921600, /* IOMEM */
- 0x40, 2, NULL, 0x200 },
+ 0, 0, pbn_computone_8 },
{ PCI_VENDOR_ID_COMPUTONE, PCI_DEVICE_ID_COMPUTONE_PG,
PCI_SUBVENDOR_ID_COMPUTONE, PCI_SUBDEVICE_ID_COMPUTONE_PG6,
- SPCI_FL_BASE0, 6, 921600, /* IOMEM */
- 0x40, 2, NULL, 0x200 },
- /* Digitan DS560-558, from jimd@esoft.com */
- { PCI_VENDOR_ID_ATT, PCI_DEVICE_ID_ATT_VENUS_MODEM,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE1, 1, 115200 },
- /* 3Com US Robotics 56k Voice Internal PCI model 5610 */
- { PCI_VENDOR_ID_USR, 0x1008,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 1, 115200 },
- /* Titan Electronic cards */
- { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_100,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 1, 921600 },
- { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_200,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 2, 921600 },
- { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_400,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 4, 921600 },
- { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_800B,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 4, 921600 },
- /* EKF addition for i960 Boards form EKF with serial port */
- { PCI_VENDOR_ID_INTEL, 0x1960,
- 0xE4BF, PCI_ANY_ID,
- SPCI_FL_BASE0, 32, 921600, /* max 256 ports */
- 8<<2, 2, pci_inteli960ni_fn, 0x10000},
+ 0, 0, pbn_computone_6 },
+
+ { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI95N,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_oxsemi },
+ { PCI_VENDOR_ID_TIMEDIA, PCI_DEVICE_ID_TIMEDIA_1889,
+ PCI_VENDOR_ID_TIMEDIA, PCI_ANY_ID, 0, 0, pbn_timedia },
+
+ { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DSERIAL,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_bt_2_115200 },
+ { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUATRO_A,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_bt_2_115200 },
+ { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUATRO_B,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_bt_2_115200 },
+ { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PORT_PLUS,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_bt_2_460800 },
+ { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUAD_A,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_bt_2_460800 },
+ { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUAD_B,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_bt_2_460800 },
+ { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_SSERIAL,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_bt_1_115200 },
+ { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PORT_650,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_bt_1_460800 },
+
/* RAStel 2 port modem, gerg@moreton.com.au */
{ PCI_VENDOR_ID_MORETON, PCI_DEVICE_ID_RASTEL_2PORT,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 2, 115200 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_bt_2_115200 },
+
+ /* EKF addition for i960 Boards form EKF with serial port */
+ { PCI_VENDOR_ID_INTEL, 0x1960,
+ 0xE4BF, PCI_ANY_ID, 0, 0,
+ pbn_intel_i960 },
+
+ /* Xircom Cardbus/Ethernet combos */
+ { PCI_VENDOR_ID_XIRCOM, PCI_DEVICE_ID_XIRCOM_X3201_MDM,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_xircom_combo },
+
/*
* Untested PCI modems, sent in from various folks...
*/
+
/* Elsa Model 56K PCI Modem, from Andreas Rath <arh@01019freenet.de> */
{ PCI_VENDOR_ID_ROCKWELL, 0x1004,
- 0x1048, 0x1500,
- SPCI_FL_BASE1, 1, 115200 },
+ 0x1048, 0x1500, 0, 0,
+ pbn_b1_1_115200 },
+
{ PCI_VENDOR_ID_SGI, PCI_DEVICE_ID_SGI_IOC3,
- 0xFF00, 0, SPCI_FL_BASE0 | SPCI_FL_IRQRESOURCE,
- 1, 458333, 0, 0, 0, 0x20178 },
-#if CONFIG_DDB5074
+ 0xFF00, 0, 0, 0,
+ pbn_sgi_ioc3 },
+
+#ifdef CONFIG_DDB5074
/*
* NEC Vrc-5074 (Nile 4) builtin UART.
* Conditionally compiled in since this is a motherboard device.
*/
{ PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_NILE4,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE0, 1, 520833,
- 64, 3, NULL, 0x300 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_nec_nile4 },
#endif
+
#if 0 /* PCI_DEVICE_ID_DCI_PCCOM8 ? */
{ PCI_VENDOR_ID_DCI, PCI_DEVICE_ID_DCI_PCCOM8,
- PCI_ANY_ID, PCI_ANY_ID,
- SPCI_FL_BASE3, 8, 115200,
- 8 },
-#endif
- /* Generic serial board */
- { 0, 0,
- 0, 0,
- SPCI_FL_BASE0, 1, 115200 },
-};
-
-/*
- * Given a complete unknown PCI device, try to use some heuristics to
- * guess what the configuration might be, based on the pitiful PCI
- * serial specs. Returns 0 on success, 1 on failure.
- */
-static int _INLINE_ serial_pci_guess_board(struct pci_dev *dev,
- struct pci_board *board)
-{
- int num_iomem = 0, num_port = 0, first_port = -1;
- int i;
-
- /*
- * If it is not a communications device or the programming
- * interface is greater than 6, give up.
- *
- * (Should we try to make guesses for multiport serial devices
- * later?)
- */
- if ((((dev->class >> 8) != PCI_CLASS_COMMUNICATION_SERIAL) &&
- ((dev->class >> 8) != PCI_CLASS_COMMUNICATION_MODEM)) ||
- (dev->class & 0xff) > 6)
- return 1;
-
- for (i=0; i < 6; i++) {
- if (IS_PCI_REGION_IOPORT(dev, i)) {
- num_port++;
- if (first_port == -1)
- first_port = i;
- }
- if (IS_PCI_REGION_IOMEM(dev, i))
- num_iomem++;
- }
-
- /*
- * If there is 1 or 0 iomem regions, and exactly one port, use
- * it.
- */
- if (num_iomem <= 1 && num_port == 1) {
- board->flags = first_port;
- return 0;
- }
- return 1;
-}
-
-static int __devinit serial_init_one(struct pci_dev *dev,
- const struct pci_device_id *ent)
-{
- struct pci_board *board, tmp;
- int rc;
-
- for (board = pci_boards; board->vendor; board++) {
- if (board->vendor != (unsigned short) PCI_ANY_ID &&
- dev->vendor != board->vendor)
- continue;
- if (board->device != (unsigned short) PCI_ANY_ID &&
- dev->device != board->device)
- continue;
- if (board->subvendor != (unsigned short) PCI_ANY_ID &&
- pci_get_subvendor(dev) != board->subvendor)
- continue;
- if (board->subdevice != (unsigned short) PCI_ANY_ID &&
- pci_get_subdevice(dev) != board->subdevice)
- continue;
- break;
- }
-
- rc = pci_enable_device(dev);
- if (rc) return rc;
-
- if (board->vendor == 0 && serial_pci_guess_board(dev, board))
- return -ENODEV;
- else if (serial_pci_guess_board(dev, &tmp) == 0) {
- printk(KERN_INFO "Redundant entry in serial pci_table. "
- "Please send the output of\n"
- "lspci -vv, this message (%d,%d,%d,%d)\n"
- "and the manufacturer and name of "
- "serial board or modem board\n"
- "to serial-pci-info@lists.sourceforge.net.\n",
- dev->vendor, dev->device,
- pci_get_subvendor(dev), pci_get_subdevice(dev));
- }
-
- start_pci_pnp_board(dev, board);
-
- return 0;
-}
-
-static void __devexit serial_remove_one(struct pci_dev *dev)
-{
- int i;
-
- /*
- * Iterate through all of the ports finding those that belong
- * to this PCI device.
- */
- for(i = 0; i < NR_PORTS; i++) {
- if (rs_table[i].dev != dev)
- continue;
- unregister_serial(i);
- rs_table[i].dev = 0;
- }
- /*
- * Now execute any board-specific shutdown procedure
- */
- for (i=0; i < NR_PCI_BOARDS; i++) {
- struct pci_board_inst *brd = &serial_pci_board[i];
-
- if (serial_pci_board[i].dev != dev)
- continue;
- if (brd->board.init_fn)
- (brd->board.init_fn)(brd->dev, &brd->board, 0);
- if (DEACTIVATE_FUNC(brd->dev))
- (DEACTIVATE_FUNC(brd->dev))(brd->dev);
- serial_pci_board[i].dev = 0;
- }
-}
-
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_dci_pccom8 },
+#endif
-static struct pci_device_id serial_pci_tbl[] __devinitdata = {
{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_COMMUNICATION_SERIAL << 8, 0xffff00, },
{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
@@ -5148,11 +5278,9 @@
break;
if (pnp_board->vendor) {
- board.vendor = pnp_board->vendor;
- board.device = pnp_board->device;
/* Special case that's more efficient to hardcode */
- if ((board.vendor == ISAPNP_VENDOR('A', 'K', 'Y') &&
- board.device == ISAPNP_DEVICE(0x1021)))
+ if ((pnp_board->vendor == ISAPNP_VENDOR('A', 'K', 'Y') &&
+ pnp_board->device == ISAPNP_DEVICE(0x1021)))
board.flags |= SPCI_FL_NO_SHIRQ;
} else {
if (serial_pnp_guess_board(dev, &board))
Index: linux_2_4/include/linux/serialP.h
diff -u linux_2_4/include/linux/serialP.h:1.1.1.25 linux_2_4/include/linux/serialP.h:1.1.1.25.34.1
--- linux_2_4/include/linux/serialP.h:1.1.1.25 Fri Apr 13 16:11:34 2001
+++ linux_2_4/include/linux/serialP.h Wed May 2 03:48:53 2001
@@ -142,10 +142,6 @@
*/
struct pci_dev;
struct pci_board {
- unsigned short vendor;
- unsigned short device;
- unsigned short subvendor;
- unsigned short subdevice;
int flags;
int num_ports;
int base_baud;
Index: linux_2_4/include/linux/pci_ids.h
diff -u linux_2_4/include/linux/pci_ids.h:1.1.1.58 linux_2_4/include/linux/pci_ids.h:1.1.1.58.2.1
--- linux_2_4/include/linux/pci_ids.h:1.1.1.58 Wed May 2 02:18:36 2001
+++ linux_2_4/include/linux/pci_ids.h Thu May 3 11:41:23 2001
@@ -978,6 +978,10 @@
#define PCI_VENDOR_ID_MUTECH 0x1159
#define PCI_DEVICE_ID_MUTECH_MV1000 0x0001
+#define PCI_VENDOR_ID_XIRCOM 0x115d
+#define PCI_DEVICE_ID_XIRCOM_X3201_ETH 0x0003
+#define PCI_DEVICE_ID_XIRCOM_X3201_MDM 0x0103
+
#define PCI_VENDOR_ID_RENDITION 0x1163
#define PCI_DEVICE_ID_RENDITION_VERITE 0x0001
#define PCI_DEVICE_ID_RENDITION_VERITE2100 0x2000
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH] make Xircom cardbus modems work
2001-05-09 13:48 ` Jeff Garzik
@ 2001-05-09 14:37 ` Tom Sightler
2001-05-09 21:29 ` Bill Nottingham
1 sibling, 0 replies; 5+ messages in thread
From: Tom Sightler @ 2001-05-09 14:37 UTC (permalink / raw)
To: Jeff Garzik, Bill Nottingham; +Cc: linux-kernel, tytso, Alessandro Suardi
> Does the attached patch work for you?
>
> serial.c still has the basic problem that there is a logical disconnect
> between the pci_boards list and the pci-device-id list: any device
> which is not PCI_CLASS_COMMUNICATION_SERIAL or
> PCI_CLASS_COMMUNICATION_MODEM will not get scanned. The solution is to
> move the PCI ids into the probe list, before the class listing. Ideally
> I would like to merge the Xircom cardbus fix with this fix, since they
> are both modifying the pci_board list and thus conflict.
>
> Except for the Xircom Cardbus update (based on your patch, Bill), this
> patch has been tested and is known to solve the problems reported to me
> which were caused by the logical disconnect.
>
> (Alessandro, Tom, tytso: the attached patch is updated for the changes
> in Bill's patch, so you haven't seen this version yet)
>
> Jeff
Just wanted to report that this patch finally fixes my Xircom Cardbus
adapter. Works like a charm.
Thanks!!
Later,
Tom
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH] make Xircom cardbus modems work
2001-05-09 13:48 ` Jeff Garzik
2001-05-09 14:37 ` Tom Sightler
@ 2001-05-09 21:29 ` Bill Nottingham
2001-05-14 9:45 ` Alessandro Suardi
1 sibling, 1 reply; 5+ messages in thread
From: Bill Nottingham @ 2001-05-09 21:29 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-kernel, tytso, Alessandro Suardi, Tom Sightler
Jeff Garzik (jgarzik@mandrakesoft.com) said:
> Bill,
>
> Does the attached patch work for you?
Yup, works fine for me (compiled in.)
Bill
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH] make Xircom cardbus modems work
2001-05-09 21:29 ` Bill Nottingham
@ 2001-05-14 9:45 ` Alessandro Suardi
0 siblings, 0 replies; 5+ messages in thread
From: Alessandro Suardi @ 2001-05-14 9:45 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Bill Nottingham, linux-kernel, tytso, Tom Sightler
Bill Nottingham wrote:
>
> Jeff Garzik (jgarzik@mandrakesoft.com) said:
> > Bill,
> >
> > Does the attached patch work for you?
>
> Yup, works fine for me (compiled in.)
>
Same here (compiled in so I can dial into our Australia PPP number
through the mobile phone over the IR serial link - also found along
with the Xircom Cardbus modem).
**thanks** Jeff for the patience and good work !
--alessandro <alessandro.suardi@oracle.com> <asuardi@uninetcom.it>
Linux: kernel 2.2.19/2.4.5-p1 glibc-2.2 gcc-2.96-69 binutils-2.11.90.0.7
Oracle: Oracle8i 8.1.7.0.1 Enterprise Edition for Linux
motto: Tell the truth, there's less to remember.
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2001-05-14 9:53 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2001-05-09 13:37 [PATCH] make Xircom cardbus modems work Bill Nottingham
2001-05-09 13:48 ` Jeff Garzik
2001-05-09 14:37 ` Tom Sightler
2001-05-09 21:29 ` Bill Nottingham
2001-05-14 9:45 ` Alessandro Suardi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).