* RE: v2.4.9 and sequential scan
@ 2001-09-17 13:07 conway, heather
2001-09-17 17:06 ` Patrick Mansfield
0 siblings, 1 reply; 5+ messages in thread
From: conway, heather @ 2001-09-17 13:07 UTC (permalink / raw)
To: 'Alan Cox', 'linux-scsi@vger.kernel.org'; +Cc: linux-kernel
[-- Attachment #1: Type: text/plain, Size: 1596 bytes --]
Hi Alan,
I tried two separate hosts, one with the aic7xxx driver using the AHA-2944UW
and one with the qla2x00 driver, both running v2.4.9 attached to external
storage. Both hosts are set to 128 for the max # of SCSI disks top be
laoded as modules and the kernel has been compiled, but no other patches or
tweaks were applied to the kernel. Both hosts panicked upon boot when
trying to scan the external bus.
The host attached to the external storage via SCSI (aic7xxx) has The host
attached via FC with the qla2x00 has only 24 devices assigned to it. The
qla2x00 driver reports trying to scan up to LUN 509 before timing out and
panicking. I have tried this a few times and I've seen the host scan up to
LUN 814 with the qla2x00 driver. I obtained a serial console trace from
both hosts and have enclosed them.
Any thoughts?
Thanks for the help.
Heather
-----Original Message-----
From: Alan Cox [mailto:alan@lxorguk.ukuu.org.uk]
Sent: Thursday, September 06, 2001 8:20 AM
To: conway, heather
Cc: linux-kernel@vger.kernel.org
Subject: Re: v2.4.9 and sequential scan
> panicking because it times out trying to scan for all of the LUNs. Same
> thing goes for another host using the Qlogic qla2x00 driver.
> Is there any timeframe for a change from sequential scanning in v2.4.x or
is
> there a work around so the hosts don't panic if they're attached to
external
> storage?
It shouldnt be panicing. Scanning is a legal scsi operation. If someone
wants to test and provide proper report luns code I'll be happy to test it
out in the -ac series then feed it on to Linus once stable
[-- Attachment #2: 70qlogic --]
[-- Type: application/octet-stream, Size: 45789 bytes --]
Linux version 2.4.9 (root@l82bc070.lss.emc.com) (gcc version 2.96 20000731 (Red Hat Linux 7.0)) #1 SMP Thu Sep 13 13:13:34 EDT 2001
\rBIOS-provided physical RAM map:
\r BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
\r BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
\r BIOS-e820: 00000000000e8800 - 0000000000100000 (reserved)
\r BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
\r BIOS-e820: 000000000fff0000 - 000000000ffffc00 (ACPI data)
\r BIOS-e820: 000000000ffffc00 - 0000000010000000 (ACPI NVS)
\r BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
\r BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
\r BIOS-e820: 00000000fffe8800 - 0000000100000000 (reserved)
\rScan SMP from c0000000 for 1024 bytes.
\rScan SMP from c009fc00 for 1024 bytes.
\rScan SMP from c00f0000 for 65536 bytes.
\rfound SMP MP-table at 000f6e10
\rhm, page 000f6000 reserved twice.
\rhm, page 000f7000 reserved twice.
\rhm, page 0009f000 reserved twice.
\rhm, page 000a0000 reserved twice.
\rOn node 0 totalpages: 65520
\rzone(0): 4096 pages.
\rzone(1): 61424 pages.
\rzone(2): 0 pages.
\rIntel MultiProcessor Specification v1.4
\r Virtual Wire compatibility mode.
\rOEM ID: HP Product ID: LH 4 APIC at: 0xFEE00000
\rProcessor #1 Pentium(tm) Pro APIC version 17
\r Floating point unit present.
\r Machine Exception supported.
\r 64 bit compare & exchange supported.
\r Internal APIC present.
\r SEP present.
\r MTRR present.
\r PGE present.
\r MCA present.
\r CMOV present.
\r PAT present.
\r PSE present.
\r PSN present.
\r MMX present.
\r FXSR present.
\r XMM present.
\r Bootup CPU
\rProcessor #0 Pentium(tm) Pro APIC version 17
\r Floating point unit present.
\r Machine Exception supported.
\r 64 bit compare & exchange supported.
\r Internal APIC present.
\r SEP present.
\r MTRR present.
\r PGE present.
\r MCA present.
\r CMOV present.
\r PAT present.
\r PSE present.
\r PSN present.
\r MMX present.
\r FXSR present.
\r XMM present.
\rBus #0 is PCI
\rBus #1 is PCI
\rBus #2 is PCI
\rBus #3 is ISA
\rI/O APIC #2 Version 17 at 0xFEC00000.
\rInt: type 3, pol 1, trig 1, bus 3, IRQ 00, APIC ID 2, APIC INT 00
\rInt: type 0, pol 1, trig 1, bus 3, IRQ 01, APIC ID 2, APIC INT 01
\rInt: type 0, pol 1, trig 1, bus 3, IRQ 00, APIC ID 2, APIC INT 02
\rInt: type 0, pol 1, trig 1, bus 3, IRQ 03, APIC ID 2, APIC INT 03
\rInt: type 0, pol 1, trig 1, bus 3, IRQ 04, APIC ID 2, APIC INT 04
\rInt: type 0, pol 1, trig 3, bus 3, IRQ 05, APIC ID 2, APIC INT 05
\rInt: type 0, pol 1, trig 1, bus 3, IRQ 06, APIC ID 2, APIC INT 06
\rInt: type 0, pol 1, trig 1, bus 3, IRQ 07, APIC ID 2, APIC INT 07
\rInt: type 0, pol 1, trig 1, bus 3, IRQ 08, APIC ID 2, APIC INT 08
\rInt: type 0, pol 1, trig 1, bus 3, IRQ 09, APIC ID 2, APIC INT 09
\rInt: type 0, pol 1, trig 3, bus 3, IRQ 0a, APIC ID 2, APIC INT 0a
\rInt: type 0, pol 1, trig 3, bus 3, IRQ 0b, APIC ID 2, APIC INT 0b
\rInt: type 0, pol 1, trig 1, bus 3, IRQ 0c, APIC ID 2, APIC INT 0c
\rInt: type 0, pol 1, trig 1, bus 3, IRQ 0d, APIC ID 2, APIC INT 0d
\rInt: type 0, pol 1, trig 1, bus 3, IRQ 0e, APIC ID 2, APIC INT 0e
\rInt: type 0, pol 1, trig 3, bus 3, IRQ 0f, APIC ID 2, APIC INT 0f
\rInt: type 0, pol 1, trig 3, bus 0, IRQ 08, APIC ID 2, APIC INT 0a
\rInt: type 0, pol 1, trig 3, bus 0, IRQ 10, APIC ID 2, APIC INT 0b
\rInt: type 0, pol 1, trig 3, bus 1, IRQ 08, APIC ID 2, APIC INT 0b
\rInt: type 0, pol 1, trig 3, bus 1, IRQ 0c, APIC ID 2, APIC INT 0b
\rInt: type 0, pol 1, trig 3, bus 1, IRQ 18, APIC ID 2, APIC INT 0f
\rInt: type 0, pol 1, trig 3, bus 1, IRQ 1c, APIC ID 2, APIC INT 0f
\rInt: type 0, pol 1, trig 3, bus 2, IRQ 08, APIC ID 2, APIC INT 05
\rLint: type 3, pol 1, trig 1, bus 3, IRQ 00, APIC ID ff, APIC LINT 00
\rLint: type 1, pol 1, trig 1, bus 0, IRQ 00, APIC ID ff, APIC LINT 01
\rProcessors: 2
\rmapped APIC to ffffe000 (fee00000)
\rmapped IOAPIC to ffffd000 (fec00000)
\rKernel command line: BOOT_IMAGE=linux-2.4.9 ro root=801 BOOT_FILE=/boot/vmlinuz-2.4.9 console=ttyS0,115200
\rInitializing CPU#0
\rDetected 550.042 MHz processor.
\rConsole: colour VGA+ 80x25
\rCalibrating delay loop... 1097.72 BogoMIPS
\rMemory: 254216k/262080k available (1393k kernel code, 7476k reserved, 525k data, 236k init, 0k highmem)
\rDentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
\rInode-cache hash table entries: 16384 (order: 5, 131072 bytes)
\rMount-cache hash table entries: 4096 (order: 3, 32768 bytes)
\rBuffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
\rPage-cache hash table entries: 65536 (order: 6, 262144 bytes)
\rCPU: L1 I cache: 16K, L1 D cache: 16K
\rCPU: L2 cache: 512K
\rIntel machine check architecture supported.
\rIntel machine check reporting enabled on CPU#0.
\rCPU serial number disabled.
\rEnabling fast FPU save and restore... done.
\rEnabling unmasked SIMD FPU exception support... done.
\rChecking 'hlt' instruction... OK.
\rPOSIX conformance testing by UNIFIX
\rCPU: L1 I cache: 16K, L1 D cache: 16K
\rCPU: L2 cache: 512K
\rIntel machine check reporting enabled on CPU#0.
\rCPU0: Intel Pentium III (Katmai) stepping 03
\rper-CPU timeslice cutoff: 1462.55 usecs.
\rGetting VERSION: 40011
\rGetting VERSION: 40011
\rGetting ID: 1000000
\rGetting ID: e000000
\rGetting LVT0: 700
\rGetting LVT1: 400
\renabled ExtINT on CPU#0
\rESR value before enabling vector: 00000000
\rESR value after enabling vector: 00000000
\rCPU present map: 3
\rBooting processor 1/0 eip 2000
\rSetting warm reset code and vector.
\r1.
\r2.
\r3.
\rAsserting INIT.
\rWaiting for send to finish...
\r+Deasserting INIT.
\rWaiting for send to finish...
\r+#startup loops: 2.
\rSending STARTUP #1.
\rAfter apic_write.
\rInitializing CPU#1
\rStartup point 1.
\rCPU#1 (phys ID: 0) waiting for CALLOUT
\rWaiting for send to finish...
\r+Sending STARTUP #2.
\rAfter apic_write.
\rStartup point 1.
\rWaiting for send to finish...
\r+After Startup.
\rBefore Callout 1.
\rAfter Callout 1.
\rCALLIN, before setup_local_APIC().
\rmasked ExtINT on CPU#1
\rESR value before enabling vector: 00000000
\rESR value after enabling vector: 00000000
\rCalibrating delay loop... 1097.72 BogoMIPS
\rStack at about c1457fb8
\rCPU: L1 I cache: 16K, L1 D cache: 16K
\rCPU: L2 cache: 512K
\rIntel machine check reporting enabled on CPU#1.
\rCPU serial number disabled.
\rOK.
\rCPU1: Intel Pentium III (Katmai) stepping 03
\rCPU has booted.
\rBefore bogomips.
\rTotal of 2 processors activated (2195.45 BogoMIPS).
\rBefore bogocount - setting activated=1.
\rBoot done.
\rENABLING IO-APIC IRQs
\r...changing IO-APIC physical APIC ID to 2 ... ok.
\rSynchronizing Arb IDs.
\r..TIMER: vector=31 pin1=2 pin2=0
\r..MP-BIOS bug: 8254 timer not connected to IO-APIC
\r...trying to set up timer (IRQ0) through the 8259A ...
\r..... (found pin 0) ...works.
\rtesting the IO APIC.......................
\r.................................... done.
\rcalibrating APIC timer ...
\r..... CPU clock speed is 550.0507 MHz.
\r..... host bus clock speed is 100.0089 MHz.
\rcpu: 0, clocks: 1000089, slice: 333363
\rCPU0<T0:1000080,T1:666704,D:13,S:333363,C:1000089>
\rcpu: 1, clocks: 1000089, slice: 333363
\rCPU1<T0:1000080,T1:333344,D:10,S:333363,C:1000089>
\rchecking TSC synchronization across CPUs: passed.
\rSetting commenced=1, go go go
\rPCI: PCI BIOS revision 2.10 entry at 0xfdab2, last bus=2
\rPCI: Using configuration type 1
\rPCI: Probing PCI hardware
\rPCI: Searching for i450NX host bridges on 00:10.0
\rUnknown bridge resource 2: assuming transparent
\rUnknown bridge resource 2: assuming transparent
\rPCI: Using IRQ router PIIX [8086/7110] at 00:0f.0
\rquerying PCI -> IRQ mapping bus:0, slot:2, pin:0.
\rPCI->APIC IRQ transform: (B0,I2,P0) -> 10
\rquerying PCI -> IRQ mapping bus:0, slot:4, pin:0.
\rPCI->APIC IRQ transform: (B0,I4,P0) -> 11
\rquerying PCI -> IRQ mapping bus:0, slot:15, pin:3.
\rquerying PCI -> IRQ mapping bus:1, slot:2, pin:0.
\rPCI->APIC IRQ transform: (B1,I2,P0) -> 11
\rquerying PCI -> IRQ mapping bus:1, slot:3, pin:0.
\rPCI->APIC IRQ transform: (B1,I3,P0) -> 11
\rquerying PCI -> IRQ mapping bus:1, slot:6, pin:0.
\rPCI->APIC IRQ transform: (B1,I6,P0) -> 15
\rquerying PCI -> IRQ mapping bus:1, slot:7, pin:0.
\rPCI->APIC IRQ transform: (B1,I7,P0) -> 15
\rquerying PCI -> IRQ mapping bus:1, slot:2, pin:0.
\rPCI->APIC IRQ transform: (B1,I2,P0) -> 11
\rquerying PCI -> IRQ mapping bus:1, slot:3, pin:0.
\rPCI->APIC IRQ transform: (B1,I3,P0) -> 11
\rquerying PCI -> IRQ mapping bus:1, slot:6, pin:0.
\rPCI->APIC IRQ transform: (B1,I6,P0) -> 15
\rquerying PCI -> IRQ mapping bus:1, slot:7, pin:0.
\rPCI->APIC IRQ transform: (B1,I7,P0) -> 15
\rquerying PCI -> IRQ mapping bus:2, slot:2, pin:0.
\rPCI->APIC IRQ transform: (B2,I2,P0) -> 5
\rPCI: Cannot allocate resource region 0 of device 01:02.0
\rPCI: Cannot allocate resource region 1 of device 01:02.0
\rPCI: Cannot allocate resource region 0 of device 01:03.0
\rPCI: Cannot allocate resource region 1 of device 01:03.0
\rPCI: Cannot allocate resource region 0 of device 01:06.0
\rPCI: Cannot allocate resource region 1 of device 01:06.0
\rPCI: Cannot allocate resource region 2 of device 01:06.0
\rPCI: Cannot allocate resource region 0 of device 01:07.0
\rPCI: Cannot allocate resource region 1 of device 01:07.0
\rPCI: Cannot allocate resource region 2 of device 01:07.0
\r got res[1400:14ff] for resource 0 of Adaptec AHA-294x / AIC-7884U
\r got res[10000000:10000fff] for resource 1 of Adaptec AHA-294x / AIC-7884U
\r got res[1800:18ff] for resource 0 of Adaptec AHA-294x / AIC-7884U (#2)
\r got res[10001000:10001fff] for resource 1 of Adaptec AHA-294x / AIC-7884U (#2)
\r got res[1c00:1cff] for resource 0 of Symbios Logic Inc. (formerly NCR) 53c895
\r got res[10002000:100020ff] for resource 1 of Symbios Logic Inc. (formerly NCR) 53c895
\r got res[10003000:10003fff] for resource 2 of Symbios Logic Inc. (formerly NCR) 53c895
\r got res[2000:20ff] for resource 0 of Symbios Logic Inc. (formerly NCR) 53c895 (#2)
\r got res[10002100:100021ff] for resource 1 of Symbios Logic Inc. (formerly NCR) 53c895 (#2)
\r got res[10004000:10004fff] for resource 2 of Symbios Logic Inc. (formerly NCR) 53c895 (#2)
\risapnp: Scanning for PnP cards...
\risapnp: No Plug & Play device found
\rLinux NET4.0 for Linux 2.4
\rBased upon Swansea University Computer Society NET3.039
\rStarting kswapd v1.8
\rpty: 256 Unix98 ptys configured
\rSerial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
\rttyS00 at 0x03f8 (irq = 4) is a 16550A
\rttyS01 at 0x02f8 (irq = 3) is a 16550A
\rblock: 128 slots per queue, batch=16
\rRAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
\rUniform Multi-Platform E-IDE driver Revision: 6.31
\ride: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
\rPIIX4: IDE controller on PCI bus 00 dev 79
\rPIIX4: chipset revision 1
\rPIIX4: not 100% native mode: will probe irqs later
\r ide0: BM-DMA at 0x9420-0x9427, BIOS settings: hda:pio, hdb:pio
\rPIIX4: IDE controller on PCI bus 00 dev 80
\rPIIX4: device not capable of full native PCI mode
\rPIIX4: device disabled (BIOS)
\rhda: HITACHI CDR-8435, ATAPI CD/DVD-ROM drive
\ride0 at 0x1f0-0x1f7,0x3f6 on irq 14
\rhda: ATAPI 32X CD-ROM drive, 128kB Cache, DMA
\rUniform CD-ROM driver Revision: 3.12
\rFloppy drive(s): fd0 is 1.44M
\rFDC 0 is a National Semiconductor PC87306
\rloop: loaded (max 8 devices)
\reepro100.c:v1.09j-t 9/29/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
\reepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
\reth0: OEM i82557/i82558 10/100 Ethernet, 00:D0:B7:3E:46:DA, IRQ 5.
\r Board assembly 733470-004, Physical connectors present: RJ45
\r Primary interface chip i82555 PHY #1.
\r General self-test: passed.
\r Serial sub-system self-test: passed.
\r Internal registers self-test: passed.
\r ROM checksum self-test: passed (0x04f4518b).
\rLinux agpgart interface v0.99 (c) Jeff Hartmann
\ragpgart: Maximum main memory to use for agp memory: 203M
\r[drm] Initialized tdfx 1.0.0 20010216 on minor 0
\r[drm] Initialized radeon 1.1.1 20010405 on minor 1
\rSCSI subsystem driver Revision: 1.00
\rsym53c8xx: at PCI bus 1, device 6, function 0
\rsym53c8xx: 53c895 detected
\rsym53c8xx: at PCI bus 1, device 7, function 0
\rsym53c8xx: 53c895 detected
\rsym53c895-0: rev 0x1 on pci bus 1 device 6 function 0 irq 15
\rsym53c895-0: ID 7, Fast-40, Parity Checking
\rCACHE TEST FAILED: reg dstat-sstat2 readback ffffffff.
\rCACHE INCORRECTLY CONFIGURED.
\rsym53c895-0: giving up ...
\rsym53c895-0: rev 0x1 on pci bus 1 device 7 function 0 irq 15
\rsym53c895-0: ID 7, Fast-40, Parity Checking
\rCACHE TEST FAILED: reg dstat-sstat2 readback ffffffff.
\rCACHE INCORRECTLY CONFIGURED.
\rsym53c895-0: giving up ...
\rrequest_module[scsi_hostadapter]: Root fs not mounted
\rrequest_module[scsi_hostadapter]: Root fs not mounted
\rrequest_module[scsi_hostadapter]: Root fs not mounted
\rrequest_module[scsi_hostadapter]: Root fs not mounted
\rrequest_module[scsi_hostadapter]: Root fs not mounted
\rNET4: Linux TCP/IP 1.0 for NET4.0
\rIP Protocols: ICMP, UDP, TCP, IGMP
\rIP: routing cache hash table of 2048 buckets, 16Kbytes
\rTCP: Hash tables configured (established 16384 bind 16384)
\rNET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
\rRAMDISK: Compressed image found at block 0
\rFreeing initrd memory: 627k freed
\rVFS: Mounted root (ext2 filesystem).
\rLoading aic7xxx module
aic7xxx: PCI Device 1:2:0 failed memory mapped test
\rahc_pci:1:2:0: No SCB space found
\rTrying to free free IRQ11
\raic7xxx: PCI Device 1:3:0 failed memory mapped test
\rahc_pci:1:3:0: No SCB space found
\rTrying to free free IRQ11
\rPCI: Enabling device 01:02.0 (0155 -> 0157)
\raic7xxx: PCI Device 1:2:0 failed memory mapped test
\rahc_pci:1:2:0: No SCB space found
\rTrying to free free IRQ11
\rPCI: Enabling device 01:03.0 (0155 -> 0157)
\raic7xxx: PCI Device 1:3:0 failed memory mapped test
\rahc_pci:1:3:0: No SCB space found
\rTrying to free free IRQ11
\r/lib/aic7xxx.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters
Loading qla2x00 module
qla2x00: detect() found an HBA
\rqla2x00: VID=1077 DID=2200 SSVID=1077 SSDID=2
\r(scsi): Found a QLA2200 @ bus 0, device 0x4, irq 11, iobase 0x9000
\rscsi(0): Configure NVRAM parameters...
\rscsi(0): Verifying loaded RISC code...
\rscsi(0): Verifying chip...
\rscsi(0): Waiting for LIP to complete...
\rscsi(0): LOOP UP detected
\rscsi0: Topology - (F_Port), Host Loop address 0xffff
\rscsi(0): Waiting for LIP to complete...
\rscsi0: Topology - (F_Port), Host Loop address 0xffff
\rscsi-qla0-adapter-node=200000e08b019d84;
\rscsi-qla0-adapter-port=210000e08b019d84;
\rscsi-qla0-target-0=50060482c3a0842b;
\rscsi0 : QLogic QLA2200 PCI to Fibre Channel Host Adapter: bus 0 device 4 irq 11
\r Firmware version: 2.01.34, Driver version 4.31.12
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5568
\r Type: Direct-Access ANSI SCSI revision: 02
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 255 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 256 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 257 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 258 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 259 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 260 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 261 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 262 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 263 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 264 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 265 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 266 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 267 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 268 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 269 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 270 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 271 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 272 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 273 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 274 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 275 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 276 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 277 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 278 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 279 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 280 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 281 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 282 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 283 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 284 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 285 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 286 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 287 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 288 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 289 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 290 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 291 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 292 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 293 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 294 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 295 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 296 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 297 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 298 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 299 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 300 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 301 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 302 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 303 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 304 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 305 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 306 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 307 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 308 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 309 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 310 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 311 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 312 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 313 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 314 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 315 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 316 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 317 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 318 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 319 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 320 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 321 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 322 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 323 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 324 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 325 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 326 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 327 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 328 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 329 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 330 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 331 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 332 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 333 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 334 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 335 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 336 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 337 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 338 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 339 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 340 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 341 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 342 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 343 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 344 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 345 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 346 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 347 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 348 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 349 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 350 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 351 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 352 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 353 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 354 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 355 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 356 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 357 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 358 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 359 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 360 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 361 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 362 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 363 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 364 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 365 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 366 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 367 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 368 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 369 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 370 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 371 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 372 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 373 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 374 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 375 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 376 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 377 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 378 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 379 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 380 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 381 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 382 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 383 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 384 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 385 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 386 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 387 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 388 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 389 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 390 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 391 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 392 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 393 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 394 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 395 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 396 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 397 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 398 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 399 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 400 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 401 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 402 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 403 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 404 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 405 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 406 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 407 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 408 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 409 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 410 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 411 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 412 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 413 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 414 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 415 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 416 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 417 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 418 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 419 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 420 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 421 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 422 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 423 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 424 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 425 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 426 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 427 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 428 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 429 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 430 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 431 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 432 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 433 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 434 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 435 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 436 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 437 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 438 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 439 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 440 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 441 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 442 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 443 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 444 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 445 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 446 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 447 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 448 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 449 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 450 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 451 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 452 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 453 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 454 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 455 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 456 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 457 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 458 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 459 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 460 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 461 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 462 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 463 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 464 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 465 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 466 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 467 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 468 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 469 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 470 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 471 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 472 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 473 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 474 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 475 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 476 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 477 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 478 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 479 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 480 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 481 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 482 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 483 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 484 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 485 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 486 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 487 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 488 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 489 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 490 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 491 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 492 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 493 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 494 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 495 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 496 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 497 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 498 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 499 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 500 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 501 Inquiry a0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 502 Inquiry c0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 503 Inquiry e0 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 504 Inquiry 00 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 505 Inquiry 20 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 506 Inquiry 40 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 507 Inquiry 60 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 508 Inquiry 80 00 00 ff 00
\rscsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 509 Inquiry a0 00 00 ff 00
\rUnable to handle kernel NULL pointer dereference at virtual address 0000000c
\r printing eip:
\rd082ada8
\r*pde = 00000000
\rOops: 0000
\rCPU: 1
\rEIP: 0010:[<d082ada8>]
\rEFLAGS: 00010046
\reax: 00000010 ebx: cfbf007c ecx: 00000401 edx: 00000004
\resi: cfb5f350 edi: cfb5f200 ebp: 00000000 esp: c1515c0c
\rds: 0018 es: 0018 ss: 0018
\rProcess insmod (pid: 11, stackpage=c1515000)
\rStack: 000001fe 00000000 00000246 cff219f4 cfbf0000 cfb5f200 c01d828e cfb5f200
\r c01dd4e0 00000000 cfb5f200 cff219f4 cfb5f2ac cff219f4 c01deda3 cfb5f200
\r cfb5f200 00000000 cfbf0000 cfba7a00 cff219a0 c01deaa0 00000286 c1515cc4
\rCall Trace: [<c01d828e>] [<c01dd4e0>] [<c01deda3>] [<c01deaa0>] [<c01de1ee>]
\r [<c01de24a>] [<c01d8364>] [<c01d7db0>] [<c01e1cb3>] [<c01deaa0>] [<c01a3c06>]
\r [<c01a5310>] [<c01a5460>] [<c01e1ad6>] [<c010f270>] [<c0114345>] [<d0871c40>]
\r [<c01d9343>] [<d0833017>] [<d0871c40>] [<d0871c40>] [<c0115165>] [<d0828060>]
\r [<c0107107>]
\rCode: f6 42 08 04 74 12 56 53 e8 2b 13 00 00 5d 31 c0 5a eb 5d 90
\rpid 11: killed by signal 11
kmod: failed to exec /sbin/modprobe -s -k block-major-8, errno = 2
\rVFS: Cannot open root device "801" or 08:01
\rPlease append a correct "root=" boot option
\rKernel panic: VFS: Unable to mount root fs on 08:01
[-- Attachment #3: 67capt2 --]
[-- Type: application/octet-stream, Size: 13673 bytes --]
Linux version 2.4.9 (root@l82bc067.lss.emc.com) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #5 SMP Wed Sep 12 17:47:02 EDT 2001
\rBIOS-provided physical RAM map:
\r BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
\r BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
\r BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
\r BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
\r BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved)
\r BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
\rScan SMP from c0000000 for 1024 bytes.
\rScan SMP from c009fc00 for 1024 bytes.
\rScan SMP from c00f0000 for 65536 bytes.
\rfound SMP MP-table at 000fdb90
\rhm, page 000fd000 reserved twice.
\rhm, page 000fe000 reserved twice.
\rhm, page 0009f000 reserved twice.
\rhm, page 000a0000 reserved twice.
\rOn node 0 totalpages: 131072
\rzone(0): 4096 pages.
\rzone(1): 126976 pages.
\rzone(2): 0 pages.
\rIntel MultiProcessor Specification v1.4
\r Virtual Wire compatibility mode.
\rOEM ID: SNI D992 Product ID: PRIMERGY APIC at: 0xFEE00000
\rProcessor #1 Pentium(tm) Pro APIC version 17
\r Floating point unit present.
\r Machine Exception supported.
\r 64 bit compare & exchange supported.
\r Internal APIC present.
\r SEP present.
\r MTRR present.
\r PGE present.
\r MCA present.
\r CMOV present.
\r MMX present.
\r Bootup CPU
\rProcessor #0 Pentium(tm) Pro APIC version 17
\r Floating point unit present.
\r Machine Exception supported.
\r 64 bit compare & exchange supported.
\r Internal APIC present.
\r SEP present.
\r MTRR present.
\r PGE present.
\r MCA present.
\r CMOV present.
\r MMX present.
\rBus #0 is PCI
\rBus #1 is PCI
\rBus #2 is ISA
\rI/O APIC #2 Version 17 at 0xFEC00000.
\rInt: type 3, pol 1, trig 1, bus 2, IRQ 00, APIC ID 2, APIC INT 00
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 01, APIC ID 2, APIC INT 01
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 02
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 03, APIC ID 2, APIC INT 03
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 04, APIC ID 2, APIC INT 04
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 05, APIC ID 2, APIC INT 05
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 06, APIC ID 2, APIC INT 06
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 07, APIC ID 2, APIC INT 07
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 08, APIC ID 2, APIC INT 08
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 09, APIC ID 2, APIC INT 09
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 0a, APIC ID 2, APIC INT 0a
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 0b, APIC ID 2, APIC INT 0b
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 0c, APIC ID 2, APIC INT 0c
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 0d, APIC ID 2, APIC INT 0d
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 0e, APIC ID 2, APIC INT 0e
\rInt: type 0, pol 0, trig 0, bus 2, IRQ 0f, APIC ID 2, APIC INT 0f
\rLint: type 3, pol 1, trig 1, bus 2, IRQ 00, APIC ID ff, APIC LINT 00
\rLint: type 1, pol 1, trig 1, bus 0, IRQ 00, APIC ID ff, APIC LINT 01
\rProcessors: 2
\rmapped APIC to ffffe000 (fee00000)
\rmapped IOAPIC to ffffd000 (fec00000)
\rKernel command line: BOOT_IMAGE=linux-2.4.9 ro root=801 console=ttyS0,115200 aic7xxx=verbose
\rInitializing CPU#0
\rDetected 299.154 MHz processor.
\rConsole: colour VGA+ 80x25
\rCalibrating delay loop... 596.37 BogoMIPS
\rMemory: 512196k/524288k available (1481k kernel code, 11704k reserved, 557k data, 236k init, 0k highmem)
\rDentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
\rInode-cache hash table entries: 32768 (order: 6, 262144 bytes)
\rMount-cache hash table entries: 8192 (order: 4, 65536 bytes)
\rBuffer-cache hash table ender: 7, 524288 bytes)
\rCPU: L1 I cache: 16K, L1 D cache: 16K
\rCPU: L2 cache: 512K
\rIntel machine check architecture supported.
\rIntel machine check reporting enabled on CPU#0.
\rChecking 'hlt' instruction... OK.
\rPOSIX conformance testing by UNIFIX
\rCPU: L1 I cache: 16K, L1 D cache: 16K
\rCPU: L2 cache: 512K
\rIntel machine check reporting enabled on CPU#0.
\rCPU0: Intel Pentium II (Klamath) stepping 04
\rper-CPU timeslice cutoff: 1462.89 usecs.
\rGetting VERSION: 40011
\rGetting VERSION: 40011
\rGetting ID: 1000000
\rGetting ID: e000000
\rGetting LVT0: 700
\rGetting LVT1: 400
\renabled ExtINT on CPU#0
\rESR value before enabling vector: 00000000
\rESR value after enabling vector: 00000000
\rCPU present map: 3
\rBooting processor 1/0 eip 2000
\rSetting warm reset code and vector.
\r1.
\r2.
\r3.
\rAsserting INIT.
\rWaiting for send to finish...
\r+Deasserting INIT.
\rWaiting for send to finish...
\r+#startup loops: 2.
\rSending STARTUP #1.
\rAfter apic_write.
\rInitializing CPU#1
\rStartup point 1.
\rCPU#1 (phys ID: 0) waiting for CALLOUT
\rWaiting for send to finish...
\r+Sending STARTUP #2.
\rAfter apic_write.
\rStartup point 1.
\rWaiting for send to finish...
\r+After Startup.
\rBefore Callout 1.
\rAfter Callout 1.
\rCALLIN, before setup_local_APIC().
\rmasked ExtINT on CPU#1
\rESR value before enabling vector: 00000000
\rESR value after enabling vector: 00000000
\rCalibrating delay loop... 598.01 BogoMIPS
\rStack at about dfffdfbc
\rCPU: L1 I cache: 16K, L1 D cache: 16K
\rCPU: L2 cache: 512K
\rIntel machine check reporting enabled on CPU#1.
\rOK.
\rCPU1: Intel Pentium II (Klamath) stepping 04
\rCPU has booted.
\rBefore bogomips.
\rTotal of 2 processors activated (1194.39 BogoMIPS).
\rBefore bogocount - setting activated=1.
\rBoot done.
\rENABLING IO-APIC IRQs
\r...changing IO-APIC physical APIC ID to 2 ... ok.
\rSynchronizing Arb IDs.
\r..TIMER: vector=31 pin1=2 pin2=0
\rtesting the IO APIC.......................
\r.................................... done.
\rcalibrating APIC timer ...
\r..... CPU clock speed is 299.1577 MHz.
\r..... host bus clock speed is 66.4793 MHz.
\rcpu: 0, clocks: 664793, slice: 221597
\rCPU0<T0:664784,T1:443184,D:3,S:221597,C:664793>
\rcpu: 1, clocks: 664793, slice: 221597
\rCPU1<T0:664784,T1:221584,D:6,S:221597,C:664793>
\rchecking TSC synchronization across CPUs: passed.
\rSetting commenced=1, go go go
\rPCI: PCI BIOS revision 2.10 entry at 0xf6893, last bus=1
\rPCI: Using configuration type 1
\rPCI: Probing PCI hardware
\rquerying PCI -> IRQ mapping bus:0, slot:13, pin:0.
\rquerying PCI -> IRQ mapping bus:1, slot:1, pin:0.
\rquerying PCI -> IRQ mapping bus:0, slot:3, pin:1.
\rquerying PCI -> IRQ mapping bus:1, slot:8, pin:0.
\rquerying PCI -> IRQ mapping bus:0, slot:3, pin:0.
\rquerying PCI -> IRQ mapping bus:1, slot:9, pin:0.
\rquerying PCI -> IRQ mapping bus:0, slot:3, pin:1.
\rPCI: Cannot allocate resource region 0 of device 00:02.0
\rPCI: Error while updating region 00:02.0/0 (20000000 != fec00000)
\r got res[20000000:200003ff] for resource 0 of PCI device 110a:0015 (Siemens Nixdorf AG)
\rLimiting direct PCI/PCI transfers.
\rActivating ISA DMA hang workarounds.
\risapnp: Scanning for PnP cards...
\risapnp: Card 'Adaptec AHA-1510B'
\risapnp: 1 Plug & Play card detected total
\rLinux NET4.0 for Linux 2.4
\rBased upon Swansea University Computer Society NET3.039
\rStarting kswapd v1.8
\rpty: 256 Unix98 ptys configured
\rSerial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
\rttyS00 at 0x03f8 (irq = 4) is a 16550A
\rttyS01 at 0x02f8 (irq = 3) is a 16550A
\rblock: 128 slots per queue, batch=16
\rRAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
\rUniform Multi-Platform E-IDE driver Revision: 6.31
\ride: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
\rPIIX3: IDE controller on PCI bus 00 dev 09
\rPIIX3: chipset revision 0
\rPIIX3: not 100% native mode: will probe irqs later
\r ide0: BM-DMA at 0xfcf0-0xfcf7, BIOS settings: hda:pio, hdb:pio
\rFloppy drive(s): fd0 is 1.44M
\rFDC 0 is a post-1991 82077
\rloop: loaded (max 8 devices)
\reepro100.c:v1.09j-t 9/29/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
\reepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
\reth0: OEM i82557/i82558 10/100 Ethernet, 00:90:27:8A:0F:98, IRQ 15.
\r Receiver lock-up bug exists -- enabling work-around.
\r Board assembly 697680-002, Physical connectors present: RJ45
\r Primary interface chip i82555 PHY #1.
\r General self-test: passed.
\r Serial sub-system self-test: passed.
\r Internal registers self-test: passed.
\r ROM checksum self-test: passed (0x24c9f043).
\r Receiver lock-up workaround activated.
\rLinux agpgart interface v0.99 (c) Jeff Hartmann
\ragpgart: Maximum main memory to use for agp memory: 440M
\r[drm] Initialized tdfx 1.0.0 20010216 on minor 0
\r[drm] Initialized radeon 1.1.1 20010405 on minor 1
\rSCSI subsystem driver Revision: 1.00
\rahc_pci:1:1:0: Reading SEEPROM...checksum error
\rahc_pci:1:1:0: No SEEPROM available.
\rahc_pci:1:1:0: Using left over BIOS settings
\rahc_pci:1:1:0: Downloading Sequencer Program... 439 instructions downloaded
\rahc_pci:1:8:0: Reading SEEPROM...done.
\rahc_pci:1:8:0: internal 50 cable not present, internal 68 cable not present
\rahc_pci:1:8:0: external cable is present
\rahc_pci:1:8:0: BIOS eeprom is present
\rahc_pci:1:8:0: High byte termination Enabled
\rahc_pci:1:8:0: Low byte termination Enabled
\rahc_pci:1:8:0: Downloading Sequencer Program... 431 instructions downloaded
\rahc_pci:1:9:0: Reading SEEPROM...checksum error
\rahc_pci:1:9:0: No SEEPROM available.
\rahc_pci:1:9:0: Host Adapter Bios disabled. Using default SCSI device parameters
\rahc_pci:1:9:0: Downloading Sequencer Program... 439 instructions downloaded
\rscsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.2
\r <Adaptec aic7880 Ultra SCSI adapter>
\r aic7880: Ultra Wide Channel A, SCSI Id=7, 16/255 SCBs
\rscsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.2
\r <Adaptec 2944 Ultra SCSI adapter>
\r aic7880: Ultra Wide Channel A, SCSI Id=7, 16/255 SCBs
\rscsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.2
\r <Adaptec 2944 Ultra SCSI adapter>
\r aic7880: Ultra Wide Channel A, SCSI Id=7, 16/255 SCBs
\r Vendor: WDIGTL Model: ENTERPRISE Rev: 1.91
\r Type: Direct-Access ANSI SCSI revision: 02
\r(scsi0:A:0:1): Sending WDTR 1
\r(scsi0:A:0:1): Received WDTR 1 filtered to 1
\r(scsi0:A:0): 6.600MB/s transfers (16bit)
\rscsi0: target 0 using 16bit transfers
\r(scsi0:A:0:1): Sending SDTR period 19, offset 8
\r(scsi0:A:0:1): Received SDTR period 19, offset 8
\r Filtered to period 19, offset 8
\r(scsi0:A:0): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
\rscsi0: target 0 synchronous at 10.0MHz, offset = 0x8
\r Vendor: SDR Model: GEM200 Rev: 2
\r Type: Processor ANSI SCSI revision: 02
\r(scsi0:A:0): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
\rscsi0:A:0:0: Tagged Queuing enabled. Depth 8
\r Vendor: EMC Model: SYMMETRIX Rev: 5268
\r Type: Direct-Access ANSI SCSI revision: 02
\r(scsi1:A:0:1): Sending WDTR 1
\r(scsi1:A:0:1): Received WDTR 1 filtered to 1
\r(scsi1:A:0): 6.600MB/s transfers (16bit)
\rscsi1: target 0 using 16bit transfers
\r(scsi1:A:0:1): Sending SDTR period c, offset 8
\r(scsi1:A:0:1): Received SDTR period c, offset 8
\r Filtered to period c, offset 8
\r(scsi1:A:0): 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
\rscsi1: target 0 synchronous at 20.0MHz, offset = 0x8
\r Vendor: EMC Model: SYMMETRIX Rev: 5268
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5268
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5268
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5268
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5268
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5268
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5268
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5268
\r Type: Direct-Access ANSI SCSI revision: 02
\r Vendor: EMC Model: SYMMETRIX Rev: 5268
\r Type: Direct-Access ANSI SCSI revision: 02
\rUnable to handle kernel NULL pointer dereference at virtual address 00000016
\r printing eip:
\rc01e3a79
\r*pde = 00000000
\rOops: 0000
\rCPU: 0
\rEIP: 0010:[<c01e3a79>]
\rEFLAGS: 00010006
\reax: dff79800 ebx: dff57400 ecx: 00000000 edx: 0000000a
\resi: dffcf200 edi: 00000000 ebp: 00000042 esp: dfff7c60
\rds: 0018 es: 0018 ss: 0018
\rProcess swapper (pid: 1, stackpage=dfff7000)
\rStack: 00000212 dff83ef4 dff57400 dffbd7a0 00000000 00000082 c01d7f8a dff57400
\r c01d85f4 dff57400 dff83ef4 dffbd7a0 dff83ef4 00000000 c01df4bf dff57400
\r dff57400 00000286 dff57618 dfff7dbc dffbd7a0 00000000 dffbd7a0 dff57600
\rCall Trace: [<c01d7f8a>] [<c01d85f4>] [<c01df4bf>] [<c01de8d6>] [<c01de926>]
\r [<c01d8271>] [<c01d811c>] [<c01d79f8>] [<c01e219c>] [<c01a00ff>] [<c01a3700>]
\r [<c01a4fb0>] [<c01a50ec>] [<c01a510c>] [<c01e1eeb>] [<c0108955>] [<c0106ffc>]
\r [<c01e38a6>] [<c01d963a>] [<c0105000>] [<c01d9e6d>] [<c0105285>] [<c0105000>]
\r [<c0105763>]
\rCode: 8b 42 0c 89 83 64 01 00 00 8b 42 0c 89 18 81 c3 60 01 00 00
\rKernel panic: Attempted to kill init!
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: v2.4.9 and sequential scan
2001-09-17 13:07 v2.4.9 and sequential scan conway, heather
@ 2001-09-17 17:06 ` Patrick Mansfield
0 siblings, 0 replies; 5+ messages in thread
From: Patrick Mansfield @ 2001-09-17 17:06 UTC (permalink / raw)
To: conway, heather
Cc: 'Alan Cox', 'linux-scsi@vger.kernel.org', linux-kernel
On Mon, Sep 17, 2001 at 09:07:25AM -0400, conway, heather wrote:
> Hi Alan,
> I tried two separate hosts, one with the aic7xxx driver using the AHA-2944UW
> and one with the qla2x00 driver, both running v2.4.9 attached to external
> storage. Both hosts are set to 128 for the max # of SCSI disks top be
> laoded as modules and the kernel has been compiled, but no other patches or
> tweaks were applied to the kernel. Both hosts panicked upon boot when
> trying to scan the external bus.
> The host attached to the external storage via SCSI (aic7xxx) has The host
> attached via FC with the qla2x00 has only 24 devices assigned to it. The
> qla2x00 driver reports trying to scan up to LUN 509 before timing out and
> panicking. I have tried this a few times and I've seen the host scan up to
> LUN 814 with the qla2x00 driver. I obtained a serial console trace from
> both hosts and have enclosed them.
> Any thoughts?
> Thanks for the help.
> Heather
Heather -
EMC is in the device_list[] (in scsi_scan.c) as a sparse LUN device.
I don't quite follow your information about aic7xx and SCSI storage.
Doug Ledford posted a patch for this plus one other fix in:
http://marc.theaimsgroup.com/?l=linux-kernel&m=98462326721779&w=2
If you look at the current setting of *max_dev_lun, it either jumps
around (for low values of max_scsi_luns, i.e. 1), or is incremented
by 1/2 of shpnt->max_lun until it reaches max_scsi_luns (for high
values of max_scsi_luns, i.e. 0xffffffff). It is currently modified
(for sparse LUN or force LUN devices) only when you find a LUN, but
its value is set each time not just once.
Always setting it to shpnt->max_lun is not very bad - if max_lun is
high, you are on fibre/FCP, and scanning should be very fast
compared to SCSI.
Here's a patch if you want to try it out, it also sets *max_dev_lun
for the early sparse lun check (we don't need the duplicate setting
for the second sparse lun check, but it does return 1 there, so I
left the settings of *max_dev_lun and *sparse_lun).
I've compiled but haven't run with this patch, though I've previously
compiled and run when patched against an earlier version of the
kernel (2.4.5 or so).
--
Patrick Mansfield
--- linux-2.4.9/drivers/scsi/scsi_scan.c Mon Aug 13 16:36:30 2001
+++ linux-2.4.9-maxlun/drivers/scsi/scsi_scan.c Mon Sep 17 09:29:53 2001
@@ -579,7 +579,8 @@
bflags = get_device_flags (scsi_result);
if (bflags & BLIST_SPARSELUN) {
- *sparse_lun = 1;
+ *max_dev_lun = shpnt->max_lun;
+ *sparse_lun = 1;
}
/*
* Check the peripheral qualifier field - this tells us whether LUNS
@@ -795,19 +796,7 @@
* other settings, and scan all of them.
*/
if (bflags & BLIST_SPARSELUN) {
- /*
- * Scanning MAX_SCSI_LUNS units would be a bad idea.
- * Any better idea?
- * I think we need REPORT LUNS in future to avoid scanning
- * of unused LUNs. But, that is another item.
- *
- * FIXME(eric) - perhaps this should be a kernel configurable?
- */
- if (*max_dev_lun < shpnt->max_lun)
- *max_dev_lun = shpnt->max_lun;
- else if ((max_scsi_luns >> 1) >= *max_dev_lun)
- *max_dev_lun += shpnt->max_lun;
- else *max_dev_lun = max_scsi_luns;
+ *max_dev_lun = shpnt->max_lun;
*sparse_lun = 1;
return 1;
}
@@ -816,17 +805,7 @@
* settings, and scan all of them.
*/
if (bflags & BLIST_FORCELUN) {
- /*
- * Scanning MAX_SCSI_LUNS units would be a bad idea.
- * Any better idea?
- * I think we need REPORT LUNS in future to avoid scanning
- * of unused LUNs. But, that is another item.
- */
- if (*max_dev_lun < shpnt->max_lun)
- *max_dev_lun = shpnt->max_lun;
- else if ((max_scsi_luns >> 1) >= *max_dev_lun)
- *max_dev_lun += shpnt->max_lun;
- else *max_dev_lun = max_scsi_luns;
+ *max_dev_lun = shpnt->max_lun;
return 1;
}
/*
^ permalink raw reply [flat|nested] 5+ messages in thread
* RE: v2.4.9 and sequential scan
@ 2001-09-17 17:53 chen, xiangping
0 siblings, 0 replies; 5+ messages in thread
From: chen, xiangping @ 2001-09-17 17:53 UTC (permalink / raw)
To: 'Patrick Mansfield', conway, heather
Cc: 'Alan Cox', 'linux-scsi@vger.kernel.org', linux-kernel
Hi, Patrick
I have tried to the patch you mentioned below against 2.4.7.
It avoids the panic when I tries to set max_scsi_luns=128
for a aic7xxx.o driver used for a SPAESE_LUN type device.
But what bothers me is that the scsi scan stops on shpnt->max_lun,
e.g. 8, in aic7xxx driver case. As Doug Ledford mentioned,
we need to set reasonable values of shpnt->max_lun for
all controllers.
Xiangping Chen
-----Original Message-----
From: Patrick Mansfield [mailto:patman@sequent.com]
Sent: Monday, September 17, 2001 1:06 PM
To: conway, heather
Cc: 'Alan Cox'; 'linux-scsi@vger.kernel.org';
linux-kernel@vger.kernel.org
Subject: Re: v2.4.9 and sequential scan
On Mon, Sep 17, 2001 at 09:07:25AM -0400, conway, heather wrote:
> Hi Alan,
> I tried two separate hosts, one with the aic7xxx driver using the
AHA-2944UW
> and one with the qla2x00 driver, both running v2.4.9 attached to external
> storage. Both hosts are set to 128 for the max # of SCSI disks top be
> laoded as modules and the kernel has been compiled, but no other patches
or
> tweaks were applied to the kernel. Both hosts panicked upon boot when
> trying to scan the external bus.
> The host attached to the external storage via SCSI (aic7xxx) has The host
> attached via FC with the qla2x00 has only 24 devices assigned to it. The
> qla2x00 driver reports trying to scan up to LUN 509 before timing out and
> panicking. I have tried this a few times and I've seen the host scan up
to
> LUN 814 with the qla2x00 driver. I obtained a serial console trace from
> both hosts and have enclosed them.
> Any thoughts?
> Thanks for the help.
> Heather
Heather -
EMC is in the device_list[] (in scsi_scan.c) as a sparse LUN device.
I don't quite follow your information about aic7xx and SCSI storage.
Doug Ledford posted a patch for this plus one other fix in:
http://marc.theaimsgroup.com/?l=linux-kernel&m=98462326721779&w=2
If you look at the current setting of *max_dev_lun, it either jumps
around (for low values of max_scsi_luns, i.e. 1), or is incremented
by 1/2 of shpnt->max_lun until it reaches max_scsi_luns (for high
values of max_scsi_luns, i.e. 0xffffffff). It is currently modified
(for sparse LUN or force LUN devices) only when you find a LUN, but
its value is set each time not just once.
Always setting it to shpnt->max_lun is not very bad - if max_lun is
high, you are on fibre/FCP, and scanning should be very fast
compared to SCSI.
Here's a patch if you want to try it out, it also sets *max_dev_lun
for the early sparse lun check (we don't need the duplicate setting
for the second sparse lun check, but it does return 1 there, so I
left the settings of *max_dev_lun and *sparse_lun).
I've compiled but haven't run with this patch, though I've previously
compiled and run when patched against an earlier version of the
kernel (2.4.5 or so).
--
Patrick Mansfield
--- linux-2.4.9/drivers/scsi/scsi_scan.c Mon Aug 13 16:36:30 2001
+++ linux-2.4.9-maxlun/drivers/scsi/scsi_scan.c Mon Sep 17 09:29:53 2001
@@ -579,7 +579,8 @@
bflags = get_device_flags (scsi_result);
if (bflags & BLIST_SPARSELUN) {
- *sparse_lun = 1;
+ *max_dev_lun = shpnt->max_lun;
+ *sparse_lun = 1;
}
/*
* Check the peripheral qualifier field - this tells us whether LUNS
@@ -795,19 +796,7 @@
* other settings, and scan all of them.
*/
if (bflags & BLIST_SPARSELUN) {
- /*
- * Scanning MAX_SCSI_LUNS units would be a bad idea.
- * Any better idea?
- * I think we need REPORT LUNS in future to avoid scanning
- * of unused LUNs. But, that is another item.
- *
- * FIXME(eric) - perhaps this should be a kernel
configurable?
- */
- if (*max_dev_lun < shpnt->max_lun)
- *max_dev_lun = shpnt->max_lun;
- else if ((max_scsi_luns >> 1) >= *max_dev_lun)
- *max_dev_lun += shpnt->max_lun;
- else *max_dev_lun = max_scsi_luns;
+ *max_dev_lun = shpnt->max_lun;
*sparse_lun = 1;
return 1;
}
@@ -816,17 +805,7 @@
* settings, and scan all of them.
*/
if (bflags & BLIST_FORCELUN) {
- /*
- * Scanning MAX_SCSI_LUNS units would be a bad idea.
- * Any better idea?
- * I think we need REPORT LUNS in future to avoid scanning
- * of unused LUNs. But, that is another item.
- */
- if (*max_dev_lun < shpnt->max_lun)
- *max_dev_lun = shpnt->max_lun;
- else if ((max_scsi_luns >> 1) >= *max_dev_lun)
- *max_dev_lun += shpnt->max_lun;
- else *max_dev_lun = max_scsi_luns;
+ *max_dev_lun = shpnt->max_lun;
return 1;
}
/*
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: v2.4.9 and sequential scan
2001-09-06 12:10 conway, heather
@ 2001-09-06 12:19 ` Alan Cox
0 siblings, 0 replies; 5+ messages in thread
From: Alan Cox @ 2001-09-06 12:19 UTC (permalink / raw)
To: conway, heather; +Cc: 'linux-kernel@vger.kernel.org'
> panicking because it times out trying to scan for all of the LUNs. Same
> thing goes for another host using the Qlogic qla2x00 driver.
> Is there any timeframe for a change from sequential scanning in v2.4.x or is
> there a work around so the hosts don't panic if they're attached to external
> storage?
It shouldnt be panicing. Scanning is a legal scsi operation. If someone
wants to test and provide proper report luns code I'll be happy to test it
out in the -ac series then feed it on to Linus once stable
^ permalink raw reply [flat|nested] 5+ messages in thread
* v2.4.9 and sequential scan
@ 2001-09-06 12:10 conway, heather
2001-09-06 12:19 ` Alan Cox
0 siblings, 1 reply; 5+ messages in thread
From: conway, heather @ 2001-09-06 12:10 UTC (permalink / raw)
To: 'linux-kernel@vger.kernel.org'
Hi Folks,
Are there any plans to change the sequential SCSI scan to REPORT_LUNS
anytime soon? I've installed v2.4.9 on a system that is attached via
Adaptec AHA-2944UWs to an external storage box and the host will end up
panicking because it times out trying to scan for all of the LUNs. Same
thing goes for another host using the Qlogic qla2x00 driver.
Is there any timeframe for a change from sequential scanning in v2.4.x or is
there a work around so the hosts don't panic if they're attached to external
storage?
Thanks for the help.
Heather
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2001-09-17 18:01 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2001-09-17 13:07 v2.4.9 and sequential scan conway, heather
2001-09-17 17:06 ` Patrick Mansfield
-- strict thread matches above, loose matches on Subject: below --
2001-09-17 17:53 chen, xiangping
2001-09-06 12:10 conway, heather
2001-09-06 12:19 ` Alan Cox
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).