* strange hang with promise ide and 2.4.18
@ 2002-03-02 13:45 rob
2002-03-03 17:33 ` Wolfram Schlich
0 siblings, 1 reply; 4+ messages in thread
From: rob @ 2002-03-02 13:45 UTC (permalink / raw)
To: linux-kernel
Hi
I have the following:
00:14.0 Unknown mass storage controller: Promise Technology, Inc. 20267 (rev 02)
I did have three of these cards, but I gave one away. The kernel
sometimes hangs during boot with no oops or panic. It depends on the
number of cards installed and how many disks are attached. If all 3
are installed and all channels have 1 disk, or 2 cards are installed
with a disk on each channel, the boot hangs. If 3 cards are installed,
but only 5 disks are attached, it doesn't hang. if 1 card is installed
with 2 disks attached, it doesn't hang.
PDC20267: IDE controller on PCI bus 00 dev a0
PDC20267: chipset revision 2
PDC20267: not 100% native mode: will probe irqs later
PDC20267: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI
Mode.
ide2: BM-DMA at 0xec00-0xec07, BIOS settings: hde:DMA, hdf:DMA
ide3: BM-DMA at 0xec08-0xec0f, BIOS settings: hdg:DMA, hdh:pio
<hangs at this point>
If I run grub with the current configuration (2 drives on 1 card) I
get the message saying it's probing drives and then it dies in the
same way without any error.
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 5
model name : Pentium II (Deschutes)
stepping : 2
cpu MHz : 451.029
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr
bogomips : 897.84
processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 5
model name : Pentium II (Deschutes)
stepping : 2
cpu MHz : 451.029
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr
bogomips : 901.12
CPU0 CPU1
0: 60003 53994 IO-APIC-edge timer
1: 1 1 IO-APIC-edge keyboard
2: 0 0 XT-PIC cascade
3: 265 217 IO-APIC-edge serial
4: 3062 3107 IO-APIC-edge serial
8: 1 2 IO-APIC-edge rtc
14: 71692 62006 IO-APIC-edge ide0
15: 89068 86198 IO-APIC-edge ide1
16: 2939 2711 IO-APIC-level eth0
19: 8 5 IO-APIC-level ide2, ide3
NMI: 0 0
LOC: 113842 113839
ERR: 0
MIS: 0
00:00.0 Host bridge: Intel Corp. 440BX/ZX - 82443BX/ZX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at d5000000 (32-bit, prefetchable) [size=4M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00: 86 80 90 71 06 00 10 22 03 00 00 06 00 20 00 00
10: 08 00 00 d5 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: Intel Corp. 440BX/ZX - 82443BX/ZX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: d0000000-d3ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00: 86 80 91 71 07 01 20 02 03 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 20 c0 c0 a0 22
20: 00 d0 f0 d3 f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 88 00
00:07.0 ISA bridge: Intel Corp. 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 86 80 10 71 0f 00 80 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: Intel Corp. 82371AB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at f000 [size=16]
00: 86 80 11 71 05 00 80 02 01 80 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.2 USB Controller: Intel Corp. 82371AB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at d000 [size=32]
00: 86 80 12 71 05 00 80 02 01 00 03 0c 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 04 00 00
00:07.3 Bridge: Intel Corp. 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00: 86 80 13 71 03 00 80 02 02 00 80 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0b.0 SCSI storage controller: Adaptec AIC-7880U
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at d400 [size=256]
Region 1: Memory at d5520000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
00: 04 90 78 80 07 00 80 02 00 00 00 01 08 20 00 00
10: 01 d4 00 00 00 00 52 d5 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 08 08
00:13.0 Ethernet controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 08)
Subsystem: Intel Corp. EtherExpress PRO/100+ Management Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d5521000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at d800 [size=64]
Region 2: Memory at d5400000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00: 86 80 29 12 07 00 90 02 08 00 00 02 08 20 00 00
10: 00 10 52 d5 01 d8 00 00 00 00 40 d5 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 0c 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 08 38
00:14.0 Unknown mass storage controller: Promise Technology, Inc. 20267 (rev 02)
Subsystem: Promise Technology, Inc.: Unknown device 4d33
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at dc00 [size=8]
Region 1: I/O ports at e000 [size=4]
Region 2: I/O ports at e400 [size=8]
Region 3: I/O ports at e800 [size=4]
Region 4: I/O ports at ec00 [size=64]
Region 5: Memory at d5500000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [58] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 5a 10 30 4d 07 00 10 02 02 00 80 01 00 20 00 00
10: 01 dc 00 00 01 e0 00 00 01 e4 00 00 01 e8 00 00
20: 01 ec 00 00 00 00 50 d5 00 00 00 00 5a 10 33 4d
30: 00 00 00 00 58 00 00 00 00 00 00 00 0b 01 00 00
01:00.0 VGA compatible controller: ATI Technologies Inc Rage XL AGP (rev 27) (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 0008
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 0
Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at d2000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] AGP version 1.0
Status: RQ=255 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 10 4d 47 87 00 90 02 27 00 00 03 08 20 00 00
10: 00 00 00 d0 01 c0 00 00 00 00 00 d2 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 10 08 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 01 08 00
config at http://mur.org.uk/~robbie/config-2.4.18
Cheers
--
Rob Murray
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: strange hang with promise ide and 2.4.18
2002-03-02 13:45 strange hang with promise ide and 2.4.18 rob
@ 2002-03-03 17:33 ` Wolfram Schlich
2002-03-03 19:10 ` rob
2002-03-08 18:53 ` rob
0 siblings, 2 replies; 4+ messages in thread
From: Wolfram Schlich @ 2002-03-03 17:33 UTC (permalink / raw)
To: linux-kernel
On Sat, Mar 02, 2002 at 01:45:23PM +0000, rob@mur.org.uk wrote:
> Hi
>
> I have the following:
>
> 00:14.0 Unknown mass storage controller: Promise Technology, Inc. 20267 (rev 02)
>
> I did have three of these cards, but I gave one away. The kernel
> sometimes hangs during boot with no oops or panic. It depends on the
> number of cards installed and how many disks are attached. If all 3
> are installed and all channels have 1 disk, or 2 cards are installed
> with a disk on each channel, the boot hangs. If 3 cards are installed,
> but only 5 disks are attached, it doesn't hang. if 1 card is installed
> with 2 disks attached, it doesn't hang.
Have you tried Andre Hedricks IDE-patch from
http://www.kernel.org/pub/linux/kernel/people/hedrick/ide-2.4.18/ ?
You could also try to enable CONFIG_PDC202XX_BURST, but I'm not sure.
--
Mit freundlichen Gruessen / Yours sincerely
Wolfram Schlich; Berghof, D-56626 Andernach-Kell; +49-(0)2636-941194;
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: strange hang with promise ide and 2.4.18
2002-03-03 17:33 ` Wolfram Schlich
@ 2002-03-03 19:10 ` rob
2002-03-08 18:53 ` rob
1 sibling, 0 replies; 4+ messages in thread
From: rob @ 2002-03-03 19:10 UTC (permalink / raw)
To: linux-kernel
Thanks, I'll try it. Btw, I think 2.4.9 was working fine, but I haven't tried it recently.
--
Rob Murray
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: strange hang with promise ide and 2.4.18
2002-03-03 17:33 ` Wolfram Schlich
2002-03-03 19:10 ` rob
@ 2002-03-08 18:53 ` rob
1 sibling, 0 replies; 4+ messages in thread
From: rob @ 2002-03-08 18:53 UTC (permalink / raw)
To: linux-kernel
On Sun, Mar 03, 2002 at 06:33:41PM +0100, Wolfram Schlich wrote:
> Have you tried Andre Hedricks IDE-patch from
> http://www.kernel.org/pub/linux/kernel/people/hedrick/ide-2.4.18/ ?
Ok, I've tried it now, no difference. I can use 1 card but not 2. I
can't test the 3 card case because I gave the other one away.
>
> You could also try to enable CONFIG_PDC202XX_BURST, but I'm not
> sure.
I already had it enabled. Would disabling it make any difference? I
don't have much time to debug this problem.
I want to get an ata133 controller. Can anyone recommend one?
Stability is the most important criteria.
> --
> Mit freundlichen Gruessen / Yours sincerely
> Wolfram Schlich; Berghof, D-56626 Andernach-Kell; +49-(0)2636-941194;
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
--
Rob Murray
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2002-03-08 18:53 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2002-03-02 13:45 strange hang with promise ide and 2.4.18 rob
2002-03-03 17:33 ` Wolfram Schlich
2002-03-03 19:10 ` rob
2002-03-08 18:53 ` rob
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).