* 2.4.20 eepro100 oops
@ 2003-04-01 18:28 Nicholas Henke
0 siblings, 0 replies; only message in thread
From: Nicholas Henke @ 2003-04-01 18:28 UTC (permalink / raw)
To: eepro100; +Cc: saw, garzik, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 1096 bytes --]
Hey all -- I was not sure where to send this, so my applogies for the
mass send.
I am running a stock 2.4.20, and I get the following oops when I try to
insmod eepr100. I do not get the same thing when using the e100 driver.
Both are compiled as modules, and running on an updated RH 7.2.
The following is the infomation from the e100 drivers about what chipset I have:
Intel(R) PRO/100 Network Driver - version 2.1.24-k1
Copyright (c) 2002 Intel Corporation
e100: selftest OK.
e100: eth0: Intel(R) PRO/100+ Management Adapter
Mem:0xf4200000 IRQ:18 Speed:0 Mbps Dx:N/A
Hardware receive checksums enabled
cpu cycle saver enabled
e100: selftest OK.
e100: eth1: Intel(R) 82559 Fast Ethernet LAN on Motherboard
Mem:0xf4203000 IRQ:21 Speed:0 Mbps Dx:N/A
Hardware receive checksums enabled
cpu cycle saver enabled
The ooutput from ksymoops is attached as oops1_out. Please let me know
if there is any more information I can supply.
Nic
P.S Please CC me on any replies.
--
Nicholas Henke
Penguin Herder & Linux Cluster System Programmer
Liniac Project - Univ. of Pennsylvania
[-- Attachment #2: oops1 --]
[-- Type: application/octet-stream, Size: 11994 bytes --]
Linux version 2.4.20-cm2custom (root@struggles.liniac.upenn.edu) (gcc version 2.96 20000731 (Red Hat Linux 7.2 2.96-112.7.2)) #1 SMP Tue Apr 1 21:47:58 EST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003ffffc00 (ACPI data)
BIOS-e820: 000000003ffffc00 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f6ab0
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
hm, page 0009f000 reserved twice.
hm, page 000a0000 reserved twice.
On node 0 totalpages: 262128
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32752 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: INTEL Product ID: Cypress APIC at: 0xFEE00000
Processor #1 Pentium(tm) Pro APIC version 17
Processor #0 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 2
Kernel command line: ro root=/dev/hda2
Initializing CPU#0
Detected 547.627 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1091.17 BogoMIPS
Memory: 1032960k/1048512k available (1388k kernel code, 15164k reserved, 490k data, 140k init, 131008k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU serial number disabled.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Katmai) stepping 03
per-CPU timeslice cutoff: 1462.36 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/0 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1094.45 BogoMIPS
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU serial number disabled.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU1: Intel Pentium III (Katmai) stepping 03
Total of 2 processors activated (2185.62 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-9, 2-10, 2-11, 2-16, 2-17, 2-20, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 17.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 003 03 0 0 0 0 0 1 1 51
07 003 03 0 0 0 0 0 1 1 59
08 003 03 0 0 0 0 0 1 1 61
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 003 03 0 0 0 0 0 1 1 69
0d 003 03 0 0 0 0 0 1 1 71
0e 003 03 0 0 0 0 0 1 1 79
0f 003 03 0 0 0 0 0 1 1 81
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 003 03 1 1 0 1 0 1 1 89
13 003 03 1 1 0 1 0 1 1 91
14 000 00 1 0 0 0 0 0 0 00
15 003 03 1 1 0 1 0 1 1 99
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ21 -> 0:21
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 547.6131 MHz.
..... host bus clock speed is 99.5657 MHz.
cpu: 0, clocks: 995657, slice: 331885
CPU0<T0:995648,T1:663760,D:3,S:331885,C:995657>
cpu: 1, clocks: 995657, slice: 331885
CPU1<T0:995648,T1:331872,D:6,S:331885,C:995657>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfdab0, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Discovered primary peer bus ff [IRQ]
PCI: Using IRQ router PIIX [8086/7110] at 00:12.0
PCI->APIC IRQ transform: (B0,I11,P0) -> 18
PCI->APIC IRQ transform: (B0,I12,P0) -> 19
PCI->APIC IRQ transform: (B0,I12,P0) -> 19
PCI->APIC IRQ transform: (B0,I14,P0) -> 21
PCI->APIC IRQ transform: (B0,I18,P3) -> 21
PCI: Cannot allocate resource region 4 of device 00:12.1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Diskquotas version dquot_6.4.0 initialized
pty: 512 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 91
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:DMA, hdd:DMA
hda: WDC WD200BB-00AUA1, ATA DISK drive
hdb: WDC WD200BB-00AUA1, ATA DISK drive
hdd: ATAPI 52X CDROM, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c035f0e4, I/O limit 4095Mb (mask 0xffffffff)
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=2434/255/63, UDMA(33)
blk: queue c035f230, I/O limit 4095Mb (mask 0xffffffff)
hdb: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=2434/255/63, UDMA(33)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 >
hdb: hdb1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 251k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8
<Adaptec aic7896/97 Ultra2 SCSI adapter>
aic7896/97: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8
<Adaptec aic7896/97 Ultra2 SCSI adapter>
aic7896/97: Ultra2 Wide Channel B, SCSI Id=7, 32/253 SCBs
blk: queue c1cf6618, I/O limit 4095Mb (mask 0xffffffff)
Journalled Block Device driver loaded
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 140k freed
Adding Swap: 2096440k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 21:25:42 Apr 1 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0x1060, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,65), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
ip_conntrack version 2.1 (8191 buckets, 65528 max) - 292 bytes per conntrack
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
eth0: Intel Corp. 82557/8/9 [Ethernet Pro 100], 00:90:27:61:70:E4, IRQ 18.
Board assembly 721383-006, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
Unable to handle kernel NULL pointer dereference at virtual address 00000010
printing eip:
f8a39b33
*pde = 2589b001
*pte = 00000000
Oops: 0002
CPU: 0
EIP: 0010:[<f8a39b33>] Not tainted
EFLAGS: 00010206
eax: 08200000 ebx: f8a3d3c4 ecx: 00000000 edx: 00200000
esi: 00000280 edi: 00003e80 ebp: e89a5000 esp: f71b1c5c
ds: 0018 es: 0018 ss: 0018
Process modprobe (pid: 571, stackpage=f71b1000)
Stack: f8a3d3c4 f71b1c94 f8a39649 f8a40000 00000001 00000000 0000baba 00000040
01800000 00001080 e4fe7000 00000000 24fe7000 00000000 f8a3d42d f8a3d433
f8a3d438 f8a3d43d 61279000 0203e470 02010000 00004701 83067213 000c40a2
Call Trace: [<f8a3d3c4>] [<f8a39649>] [<f8a3d42d>] [<f8a3d433>] [<f8a3d438>]
[<f8a3d43d>] [<c012c74a>] [<c012c7a7>] [<c0124d00>] [<c0137b61>] [<c012c1d2>]
[<c012c1fe>] [<c01152d0>] [<c0115341>] [<c01152d0>] [<c01180ea>] [<c01181d0>]
[<f8a391e0>] [<f8a3e690>] [<f8a3e9a0>] [<c01d822c>] [<f8a3e690>] [<f8a3e9a0>]
[<c01d8292>] [<f8a3e9a0>] [<f8a3c440>] [<f8a3c31c>] [<f8a3e9a0>] [<c011d615>]
[<f8a3d67c>] [<f8a39060>] [<c0108d03>]
Code: 89 41 10 8d 76 00 8d bc 27 00 00 00 00 4e 8b 59 10 79 0f 53
[-- Attachment #3: oops1_out --]
[-- Type: application/octet-stream, Size: 6031 bytes --]
ksymoops 2.4.1 on i686 2.4.20-cm2custom. Options used
-v /boot/vmlinux (specified)
-k /proc/ksyms (default)
-l /proc/modules (default)
-o /lib/modules/2.4.20-cm2custom/ (default)
-m /boot/System.map-2.4.20-cm2custom (default)
-a i686
Error (expand_objects): cannot stat(/lib/ext3.o) for ext3
Error (expand_objects): cannot stat(/lib/jbd.o) for jbd
Error (expand_objects): cannot stat(/lib/aic7xxx.o) for aic7xxx
Error (expand_objects): cannot stat(/lib/sd_mod.o) for sd_mod
Error (expand_objects): cannot stat(/lib/scsi_mod.o) for scsi_mod
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/cdrom/driver.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/char/drm/drm.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/hotplug/vmlinux-obj.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/isdn/hisax/vmlinux-obj.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/isdn/vmlinux-obj.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/media/radio/radio.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/media/video/video.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/media/media.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/misc/misc.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/net/fc/fc.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/net/pcmcia/pcmcia_net.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/net/tokenring/tr.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/net/wan/wan.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/net/wireless/wireless_net.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/parport/driver.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/drivers/sound/sounddrivers.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/net/ipv4/netfilter/netfilter.o
Warning (read_object): no symbols in /lib/modules/2.4.20-cm2custom/build/net/ipv6/netfilter/netfilter.o
Warning (compare_maps): mismatch on symbol usb_devfs_handle , usbcore says f89dca74, /lib/modules/2.4.20-cm2custom/kernel/drivers/usb/usbcore.o says f89dc4f4. Ignoring /lib/modules/2.4.20-cm2custom/kernel/drivers/usb/usbcore.o entry
Warning (map_ksym_to_module): cannot match loaded module ext3 to a unique module object. Trace may not be reliable.
Warning (map_ksym_to_module): cannot match loaded module jbd to a unique module object. Trace may not be reliable.
Warning (map_ksym_to_module): cannot match loaded module aic7xxx to a unique module object. Trace may not be reliable.
Warning (map_ksym_to_module): cannot match loaded module sd_mod to a unique module object. Trace may not be reliable.
Warning (map_ksym_to_module): cannot match loaded module scsi_mod to a unique module object. Trace may not be reliable.
cpu: 0, clocks: 995657, slice: 331885
cpu: 1, clocks: 995657, slice: 331885
Unable to handle kernel NULL pointer dereference at virtual address 00000010
f8a39b33
*pde = 2589b001
Oops: 0002
CPU: 0
EIP: 0010:[<f8a39b33>] Not tainted
Using defaults from ksymoops -t elf32-i386
EFLAGS: 00010206
eax: 08200000 ebx: f8a3d3c4 ecx: 00000000 edx: 00200000
esi: 00000280 edi: 00003e80 ebp: e89a5000 esp: f71b1c5c
ds: 0018 es: 0018 ss: 0018
Process modprobe (pid: 571, stackpage=f71b1000)
Stack: f8a3d3c4 f71b1c94 f8a39649 f8a40000 00000001 00000000 0000baba 00000040
01800000 00001080 e4fe7000 00000000 24fe7000 00000000 f8a3d42d f8a3d433
f8a3d438 f8a3d43d 61279000 0203e470 02010000 00004701 83067213 000c40a2
Call Trace: [<f8a3d3c4>] [<f8a39649>] [<f8a3d42d>] [<f8a3d433>] [<f8a3d438>]
[<f8a3d43d>] [<c012c74a>] [<c012c7a7>] [<c0124d00>] [<c0137b61>] [<c012c1d2>]
[<c012c1fe>] [<c01152d0>] [<c0115341>] [<c01152d0>] [<c01180ea>] [<c01181d0>]
[<f8a391e0>] [<f8a3e690>] [<f8a3e9a0>] [<c01d822c>] [<f8a3e690>] [<f8a3e9a0>]
[<c01d8292>] [<f8a3e9a0>] [<f8a3c440>] [<f8a3c31c>] [<f8a3e9a0>] [<c011d615>]
[<f8a3d67c>] [<f8a39060>] [<c0108d03>]
Code: 89 41 10 8d 76 00 8d bc 27 00 00 00 00 4e 8b 59 10 79 0f 53
Error (Oops_bfd_perror): scan_arch for specified architecture Success
>>EIP; f8a39b33 <[eepro100]mdio_read+23/60> <=====
Trace; f8a3d3c4 <[eepro100].LC53+1a/1e>
Trace; f8a39649 <[eepro100]speedo_found1+3d9/730>
Trace; f8a3d42d <[eepro100].LC63+e/18>
Trace; f8a3d433 <[eepro100].LC63+14/18>
Trace; f8a3d438 <[eepro100].LC65+1/9>
Trace; f8a3d43d <[eepro100].LC65+6/9>
Trace; c012c74a <do_anonymous_page+14a/170>
Trace; c012c7a7 <do_no_page+37/250>
Trace; c0124d00 <update_process_times+20/a0>
Trace; c0137b61 <__alloc_pages+41/170>
Trace; c012c1d2 <do_wp_page+2e2/330>
Trace; c012c1fe <do_wp_page+30e/330>
Trace; c01152d0 <flush_tlb_all_ipi+0/60>
Trace; c0115341 <flush_tlb_all+11/70>
Trace; c01152d0 <flush_tlb_all_ipi+0/60>
Trace; c01180ea <remap_area_pages+20a/220>
Trace; c01181d0 <__ioremap+d0/f0>
Trace; f8a391e0 <[eepro100]eepro100_init_one+180/210>
Trace; f8a3e690 <[eepro100]eepro100_pci_tbl+0/2f4>
Trace; f8a3e9a0 <[eepro100]eepro100_driver+0/3f>
Trace; c01d822c <pci_announce_device+3c/60>
Trace; f8a3e690 <[eepro100]eepro100_pci_tbl+0/2f4>
Trace; f8a3e9a0 <[eepro100]eepro100_driver+0/3f>
Trace; c01d8292 <pci_register_driver+42/60>
Trace; f8a3e9a0 <[eepro100]eepro100_driver+0/3f>
Trace; f8a3c440 <[eepro100].text.end+51/ed1>
Trace; f8a3c31c <[eepro100]eepro100_init_module+1c/50>
Trace; f8a3e9a0 <[eepro100]eepro100_driver+0/3f>
Trace; c011d615 <sys_init_module+555/630>
Trace; f8a3d67c <[eepro100].LC37+1c/60>
Trace; f8a39060 <[eepro100]eepro100_init_one+0/210>
Trace; c0108d03 <system_call+33/38>
24 warnings and 6 errors issued. Results may not be reliable.
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2003-04-01 18:15 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2003-04-01 18:28 2.4.20 eepro100 oops Nicholas Henke
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).