* CMD640 ide driver made to work
@ 2003-10-27 12:26 Stefan Talpalaru
2003-10-27 14:35 ` Bartlomiej Zolnierkiewicz
0 siblings, 1 reply; 10+ messages in thread
From: Stefan Talpalaru @ 2003-10-27 12:26 UTC (permalink / raw)
To: andre; +Cc: linux-kernel
Hi Andre!
I own an old 486 box with a CMD640 chipset on it. It works just fine
under
the 2.2.x kernel, but not under the 2.4.x series. I modified the
"cmd640"
driver so it works and I have tested it on my hardware.
This patch is for the 2.4.22 kernel.
diff -urN linux-2.4.22/Documentation/Configure.help
linux-2.4.22-new/Documentation/Configure.help
--- linux-2.4.22/Documentation/Configure.help 2003-09-10
17:39:41.000000000 +0000
+++ linux-2.4.22-new/Documentation/Configure.help 2003-10-26
14:14:12.000000000 +0000
@@ -916,14 +916,6 @@
the "CSA-6400E PCI to IDE controller" that some people have. For
details, read <file:Documentation/ide.txt>.
-CMD640 enhanced support
-CONFIG_BLK_DEV_CMD640_ENHANCED
- This option includes support for setting/autotuning PIO modes and
- prefetch on CMD640 IDE interfaces. For details, read
- <file:Documentation/ide.txt>. If you have a CMD640 IDE interface
- and your BIOS does not already do this for you, then say Y here.
- Otherwise say N.
-
RZ1000 chipset bugfix/support
CONFIG_BLK_DEV_RZ1000
The PC-Technologies RZ1000 IDE chip is used on many common 486 and
diff -urN linux-2.4.22/drivers/ide/Config.in
linux-2.4.22-new/drivers/ide/Config.in
--- linux-2.4.22/drivers/ide/Config.in 2003-09-10 17:49:50.000000000
+0000
+++ linux-2.4.22-new/drivers/ide/Config.in 2003-10-18
21:43:37.000000000 +0000
@@ -28,7 +28,6 @@
comment 'IDE chipset support/bugfixes'
if [ "$CONFIG_BLK_DEV_IDE" != "n" ]; then
dep_bool ' CMD640 chipset bugfix/support' CONFIG_BLK_DEV_CMD640
$CONFIG_X86
- dep_bool ' CMD640 enhanced support'
CONFIG_BLK_DEV_CMD640_ENHANCED $CONFIG_BLK_DEV_CMD640
dep_bool ' ISA-PNP EIDE support' CONFIG_BLK_DEV_ISAPNP
$CONFIG_ISAPNP
if [ "$CONFIG_PCI" = "y" ]; then
bool ' PCI IDE chipset support' CONFIG_BLK_DEV_IDEPCI
diff -urN linux-2.4.22/drivers/ide/pci/cmd640.c
linux-2.4.22-new/drivers/ide/pci/cmd640.c
--- linux-2.4.22/drivers/ide/pci/cmd640.c 2003-09-10 17:49:55.000000000
+0000
+++ linux-2.4.22-new/drivers/ide/pci/cmd640.c 2003-10-26
17:07:07.000000000 +0000
@@ -1,12 +1,14 @@
/*
- * linux/drivers/ide/pci/cmd640.c Version 1.02 Sep 01, 1996
+ * linux/drivers/ide/pci/cmd640.c Version 2.00 Oct 26, 2003
*
- * Copyright (C) 1995-1996 Linus Torvalds & authors (see below)
+ * Copyright (C) 1995-2003 Linus Torvalds & authors (see below)
*/
/*
* Original authors: abramov@cecmow.enet.dec.com (Igor Abramov)
* mlord@pobox.com (Mark Lord)
+ * The guy that made it work in the 2.4.x kernel:
+ * stefantalpalaru@yahoo.com (Stefan Talpalaru)
*
* See linux/MAINTAINERS for address of current maintainer.
*
@@ -96,6 +98,8 @@
* ("fast" is necessary for 32bit I/O in some systems)
* Version 1.02 fix bug that resulted in slow "setup times"
* (patch courtesy of Zoltan Hidvegi)
+ * Version 2.00 it seems that this driver never worked in the
2.4.x
+ * kernel series. This version fixes this
problem.
*/
#undef REALLY_SLOW_IO /* most systems can safely undef this */
@@ -111,12 +115,13 @@
#include <linux/ioport.h>
#include <linux/blkdev.h>
#include <linux/hdreg.h>
+#include <linux/pci.h>
#include <linux/ide.h>
#include <linux/init.h>
-
#include <asm/io.h>
#include "ide_modes.h"
+#include "cmd640.h"
/*
* This flag is set in ide.c by the parameter: ide0=cmd640_vlb
@@ -171,42 +176,42 @@
/*
* Registers and masks for easy access by drive index:
*/
-static u8 prefetch_regs[4] = {CNTRL, CNTRL, ARTTIM23, ARTTIM23};
-static u8 prefetch_masks[4] = {CNTRL_DIS_RA0, CNTRL_DIS_RA1,
ARTTIM23_DIS_RA2, ARTTIM23_DIS_RA3};
-
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
-
-static u8 arttim_regs[4] = {ARTTIM0, ARTTIM1, ARTTIM23, ARTTIM23};
-static u8 drwtim_regs[4] = {DRWTIM0, DRWTIM1, DRWTIM23, DRWTIM23};
+static u8 prefetch_regs[4] = { CNTRL, CNTRL, ARTTIM23, ARTTIM23 };
+static u8 prefetch_masks[4] =
+ { CNTRL_DIS_RA0, CNTRL_DIS_RA1, ARTTIM23_DIS_RA2, ARTTIM23_DIS_RA3
};
+static u8 arttim_regs[4] = { ARTTIM0, ARTTIM1, ARTTIM23, ARTTIM23 };
+static u8 drwtim_regs[4] = { DRWTIM0, DRWTIM1, DRWTIM23, DRWTIM23 };
/*
* Current cmd640 timing values for each drive.
* The defaults for each are the slowest possible timings.
*/
-static u8 setup_counts[4] = {4, 4, 4, 4}; /* Address setup
count (in clocks) */
-static u8 active_counts[4] = {16, 16, 16, 16}; /* Active count
(encoded) */
-static u8 recovery_counts[4] = {16, 16, 16, 16}; /* Recovery count
(encoded) */
-
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
-
-/*
- * These are initialized to point at the devices we control
- */
-static ide_hwif_t *cmd_hwif0, *cmd_hwif1;
-static ide_drive_t *cmd_drives[4];
+static u8 setup_counts[4] = { 4, 4, 4, 4 }; /* Address setup count (in
clocks) */
+static u8 active_counts[4] = { 16, 16, 16, 16 }; /* Active count
(encoded) */
+static u8 recovery_counts[4] = { 16, 16, 16, 16 }; /* Recovery count
(encoded) */
/*
* Interface to access cmd640x registers
*/
static unsigned int cmd640_key;
-static void (*__put_cmd640_reg)(u16 reg, u8 val);
-static u8 (*__get_cmd640_reg)(u16 reg);
+static void (*put_cmd640_reg) (u16 reg, u8 val);
+static u8 (*get_cmd640_reg) (u16 reg);
/*
* This is read from the CFR reg, and is used in several places.
*/
static unsigned int cmd640_chip_version;
+static inline int
+calculate_index (ide_drive_t * drive)
+{
+ ide_hwif_t *hwif = HWIF (drive);
+ int channel = (int) hwif->channel;
+ int slave = (hwif->drives != drive);
+
+ return 2 * channel + slave;
+}
+
/*
* The CMD640x chip does not support DWORD config write cycles, but
some
* of the BIOSes use them to implement the config services.
@@ -215,100 +220,114 @@
/* PCI method 1 access */
-static void put_cmd640_reg_pci1 (u16 reg, u8 val)
+static void
+put_cmd640_reg_pci1 (u16 reg, u8 val)
{
- outb_p((reg & 0xfc) | cmd640_key, 0xcf8);
- outb_p(val, (reg & 3) | 0xcfc);
+ unsigned long flags;
+
+ spin_lock_irqsave (&ide_lock, flags);
+ outl_p ((reg & 0xfc) | cmd640_key, 0xcf8);
+ outb_p (val, (reg & 3) | 0xcfc);
+ spin_unlock_irqrestore (&ide_lock, flags);
}
-static u8 get_cmd640_reg_pci1 (u16 reg)
+static u8
+get_cmd640_reg_pci1 (u16 reg)
{
- outb_p((reg & 0xfc) | cmd640_key, 0xcf8);
- return inb_p((reg & 3) | 0xcfc);
+ u8 b;
+ unsigned long flags;
+
+ spin_lock_irqsave (&ide_lock, flags);
+ outl_p ((reg & 0xfc) | cmd640_key, 0xcf8);
+ b = inb_p ((reg & 3) | 0xcfc);
+ spin_unlock_irqrestore (&ide_lock, flags);
+ return b;
}
/* PCI method 2 access (from CMD datasheet) */
-static void put_cmd640_reg_pci2 (u16 reg, u8 val)
+static void
+put_cmd640_reg_pci2 (u16 reg, u8 val)
{
- outb_p(0x10, 0xcf8);
- outb_p(val, cmd640_key + reg);
- outb_p(0, 0xcf8);
+ unsigned long flags;
+
+ spin_lock_irqsave (&ide_lock, flags);
+ outb_p (0x10, 0xcf8);
+ outb_p (val, cmd640_key + reg);
+ outb_p (0, 0xcf8);
+ spin_unlock_irqrestore (&ide_lock, flags);
}
-static u8 get_cmd640_reg_pci2 (u16 reg)
+static u8
+get_cmd640_reg_pci2 (u16 reg)
{
u8 b;
+ unsigned long flags;
- outb_p(0x10, 0xcf8);
- b = inb_p(cmd640_key + reg);
- outb_p(0, 0xcf8);
+ spin_lock_irqsave (&ide_lock, flags);
+ outb_p (0x10, 0xcf8);
+ b = inb_p (cmd640_key + reg);
+ outb_p (0, 0xcf8);
+ spin_unlock_irqrestore (&ide_lock, flags);
return b;
}
/* VLB access */
-static void put_cmd640_reg_vlb (u16 reg, u8 val)
+static void
+put_cmd640_reg_vlb (u16 reg, u8 val)
{
- outb_p(reg, cmd640_key);
- outb_p(val, cmd640_key + 4);
-}
+ unsigned long flags;
-static u8 get_cmd640_reg_vlb (u16 reg)
-{
- outb_p(reg, cmd640_key);
- return inb_p(cmd640_key + 4);
+ spin_lock_irqsave (&ide_lock, flags);
+ outb_p (reg, cmd640_key);
+ outb_p (val, cmd640_key + 4);
+ spin_unlock_irqrestore (&ide_lock, flags);
}
-static u8 get_cmd640_reg(u16 reg)
+static u8
+get_cmd640_reg_vlb (u16 reg)
{
u8 b;
unsigned long flags;
- spin_lock_irqsave(&ide_lock, flags);
- b = __get_cmd640_reg(reg);
- spin_unlock_irqrestore(&ide_lock, flags);
+ spin_lock_irqsave (&ide_lock, flags);
+ outb_p (reg, cmd640_key);
+ b = inb_p (cmd640_key + 4);
+ spin_unlock_irqrestore (&ide_lock, flags);
return b;
}
-static void put_cmd640_reg(u16 reg, u8 val)
+static int __init
+match_pci_cmd640_device (void)
{
- unsigned long flags;
-
- spin_lock_irqsave(&ide_lock, flags);
- __put_cmd640_reg(reg,val);
- spin_unlock_irqrestore(&ide_lock, flags);
-}
-
-static int __init match_pci_cmd640_device (void)
-{
- const u8 ven_dev[4] = {0x95, 0x10, 0x40, 0x06};
+ const u8 ven_dev[4] = { 0x95, 0x10, 0x40, 0x06 };
unsigned int i;
for (i = 0; i < 4; i++) {
- if (get_cmd640_reg(i) != ven_dev[i])
+ if (get_cmd640_reg (i) != ven_dev[i])
return 0;
}
#ifdef STUPIDLY_TRUST_BROKEN_PCMD_ENA_BIT
- if ((get_cmd640_reg(PCMD) & PCMD_ENA) == 0) {
- printk("ide: cmd640 on PCI disabled by BIOS\n");
+ if ((get_cmd640_reg (PCMD) & PCMD_ENA) == 0) {
+ printk ("ide: cmd640 on PCI disabled by BIOS\n");
return 0;
}
-#endif /* STUPIDLY_TRUST_BROKEN_PCMD_ENA_BIT */
- return 1; /* success */
+#endif /* STUPIDLY_TRUST_BROKEN_PCMD_ENA_BIT */
+ return 1; /* success */
}
/*
* Probe for CMD640x -- pci method 1
*/
-static int __init probe_for_cmd640_pci1 (void)
+static int __init
+probe_for_cmd640_pci1 (void)
{
- __get_cmd640_reg = get_cmd640_reg_pci1;
- __put_cmd640_reg = put_cmd640_reg_pci1;
- for (cmd640_key = 0x80000000;
- cmd640_key <= 0x8000f800;
+ get_cmd640_reg = get_cmd640_reg_pci1;
+ put_cmd640_reg = put_cmd640_reg_pci1;
+ for (cmd640_key = 0x80000000; cmd640_key <= 0x8000f800;
cmd640_key += 0x800) {
- if (match_pci_cmd640_device())
- return 1; /* success */
+ if (match_pci_cmd640_device ())
+ return 1; /* success */
}
return 0;
}
@@ -316,13 +335,14 @@
/*
* Probe for CMD640x -- pci method 2
*/
-static int __init probe_for_cmd640_pci2 (void)
+static int __init
+probe_for_cmd640_pci2 (void)
{
- __get_cmd640_reg = get_cmd640_reg_pci2;
- __put_cmd640_reg = put_cmd640_reg_pci2;
+ get_cmd640_reg = get_cmd640_reg_pci2;
+ put_cmd640_reg = put_cmd640_reg_pci2;
for (cmd640_key = 0xc000; cmd640_key <= 0xcf00; cmd640_key += 0x100)
{
- if (match_pci_cmd640_device())
- return 1; /* success */
+ if (match_pci_cmd640_device ())
+ return 1; /* success */
}
return 0;
}
@@ -330,63 +350,66 @@
/*
* Probe for CMD640x -- vlb
*/
-static int __init probe_for_cmd640_vlb (void)
+static int __init
+probe_for_cmd640_vlb (void)
{
u8 b;
- __get_cmd640_reg = get_cmd640_reg_vlb;
- __put_cmd640_reg = put_cmd640_reg_vlb;
+ get_cmd640_reg = get_cmd640_reg_vlb;
+ put_cmd640_reg = put_cmd640_reg_vlb;
cmd640_key = 0x178;
- b = get_cmd640_reg(CFR);
+ b = get_cmd640_reg (CFR);
if (b == 0xff || b == 0x00 || (b & CFR_AT_VESA_078h)) {
cmd640_key = 0x78;
- b = get_cmd640_reg(CFR);
+ b = get_cmd640_reg (CFR);
if (b == 0xff || b == 0x00 || !(b & CFR_AT_VESA_078h))
return 0;
}
- return 1; /* success */
+ return 1; /* success */
}
/*
* Returns 1 if an IDE interface/drive exists at 0x170,
* Returns 0 otherwise.
*/
-static int __init secondary_port_responding (void)
+static int __init
+secondary_port_responding (void)
{
unsigned long flags;
- spin_lock_irqsave(&ide_lock, flags);
+ spin_lock_irqsave (&ide_lock, flags);
- outb_p(0x0a, 0x170 + IDE_SELECT_OFFSET); /* select drive0 */
- udelay(100);
- if ((inb_p(0x170 + IDE_SELECT_OFFSET) & 0x1f) != 0x0a) {
- outb_p(0x1a, 0x170 + IDE_SELECT_OFFSET); /* select drive1 */
- udelay(100);
- if ((inb_p(0x170 + IDE_SELECT_OFFSET) & 0x1f) != 0x1a) {
- spin_unlock_irqrestore(&ide_lock, flags);
- return 0; /* nothing responded */
+ outb_p (0x0a, 0x170 + IDE_SELECT_OFFSET); /* select drive0 */
+ udelay (100);
+ if ((inb_p (0x170 + IDE_SELECT_OFFSET) & 0x1f) != 0x0a) {
+ outb_p (0x1a, 0x170 + IDE_SELECT_OFFSET); /* select drive1 */
+ udelay (100);
+ if ((inb_p (0x170 + IDE_SELECT_OFFSET) & 0x1f) != 0x1a) {
+ spin_unlock_irqrestore (&ide_lock, flags);
+ return 0; /* nothing responded */
}
}
- spin_unlock_irqrestore(&ide_lock, flags);
- return 1; /* success */
+ spin_unlock_irqrestore (&ide_lock, flags);
+ return 1; /* success */
}
#ifdef CMD640_DUMP_REGS
/*
* Dump out all cmd640 registers. May be called from ide.c
*/
-static void cmd640_dump_regs (void)
+static void __init
+cmd640_dump_regs (void)
{
unsigned int reg = cmd640_vlb ? 0x50 : 0x00;
/* Dump current state of chip registers */
- printk("ide: cmd640 internal register dump:");
+ printk ("ide: cmd640 internal register dump:");
for (; reg <= 0x59; reg++) {
if (!(reg & 0x0f))
- printk("\n%04x:", reg);
- printk(" %02x", get_cmd640_reg(reg));
+ printk ("\n%04x:", reg);
+ printk (" %02x", get_cmd640_reg (reg));
}
- printk("\n");
+ printk ("\n");
}
#endif
@@ -394,12 +417,14 @@
* Check whether prefetch is on for a drive,
* and initialize the unmask flags for safe operation.
*/
-static void __init check_prefetch (unsigned int index)
+static void __init
+check_prefetch (ide_drive_t * drive)
{
- ide_drive_t *drive = cmd_drives[index];
- u8 b = get_cmd640_reg(prefetch_regs[index]);
+ int index = calculate_index (drive);
+ u8 b = get_cmd640_reg (prefetch_regs[index]);
- if (b & prefetch_masks[index]) { /* is prefetch off? */
+ if (b & prefetch_masks[index]) {
+ /* is prefetch off? */
drive->no_unmask = 0;
drive->no_io_32bit = 1;
drive->io_32bit = 0;
@@ -413,44 +438,20 @@
}
/*
- * Figure out which devices we control
- */
-static void __init setup_device_ptrs (void)
-{
- unsigned int i;
-
- cmd_hwif0 = &ide_hwifs[0]; /* default, if not found below */
- cmd_hwif1 = &ide_hwifs[1]; /* default, if not found below */
- for (i = 0; i < MAX_HWIFS; i++) {
- ide_hwif_t *hwif = &ide_hwifs[i];
- if (hwif->chipset == ide_unknown || hwif->chipset == ide_generic) {
- if (hwif->io_ports[IDE_DATA_OFFSET] == 0x1f0)
- cmd_hwif0 = hwif;
- else if (hwif->io_ports[IDE_DATA_OFFSET] == 0x170)
- cmd_hwif1 = hwif;
- }
- }
- cmd_drives[0] = &cmd_hwif0->drives[0];
- cmd_drives[1] = &cmd_hwif0->drives[1];
- cmd_drives[2] = &cmd_hwif1->drives[0];
- cmd_drives[3] = &cmd_hwif1->drives[1];
-}
-
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
-
-/*
* Sets prefetch mode for a drive.
*/
-static void set_prefetch_mode (unsigned int index, int mode)
+static void
+set_prefetch_mode (ide_drive_t * drive, int mode)
{
- ide_drive_t *drive = cmd_drives[index];
+ int index = calculate_index (drive);
int reg = prefetch_regs[index];
u8 b;
unsigned long flags;
- spin_lock_irqsave(&ide_lock, flags);
- b = __get_cmd640_reg(reg);
- if (mode) { /* want prefetch on? */
+ spin_lock_irqsave (&ide_lock, flags);
+ b = get_cmd640_reg (reg);
+ if (mode) {
+ /* want prefetch on? */
#if CMD640_PREFETCH_MASKS
drive->no_unmask = 1;
drive->unmask = 0;
@@ -463,15 +464,17 @@
drive->io_32bit = 0;
b |= prefetch_masks[index]; /* disable prefetch */
}
- __put_cmd640_reg(reg, b);
- spin_unlock_irqrestore(&ide_lock, flags);
+ put_cmd640_reg (reg, b);
+ spin_unlock_irqrestore (&ide_lock, flags);
}
/*
* Dump out current drive clocks settings
*/
-static void display_clocks (unsigned int index)
+static void __init
+display_clocks (ide_drive_t * drive)
{
+ int index = calculate_index (drive);
u8 active_count, recovery_count;
active_count = active_counts[index];
@@ -481,15 +484,17 @@
if (active_count > 3 && recovery_count == 1)
++recovery_count;
if (cmd640_chip_version > 1)
- recovery_count += 1; /* cmd640b uses (count + 1)*/
- printk(", clocks=%d/%d/%d\n", setup_counts[index], active_count,
recovery_count);
+ recovery_count += 1; /* cmd640b uses (count + 1) */
+ printk (", clocks=%d/%d/%d\n", setup_counts[index], active_count,
+ recovery_count);
}
/*
* Pack active and recovery counts into single byte representation
* used by controller
*/
-inline static u8 pack_nibbles (u8 upper, u8 lower)
+inline static u8
+pack_nibbles (u8 upper, u8 lower)
{
return ((upper & 0x0f) << 4) | (lower & 0x0f);
}
@@ -497,41 +502,52 @@
/*
* This routine retrieves the initial drive timings from the chipset.
*/
-static void __init retrieve_drive_counts (unsigned int index)
+static void __init
+retrieve_drive_counts (ide_drive_t * drive)
{
+ int index = calculate_index (drive);
u8 b;
/*
* Get the internal setup timing, and convert to clock count
*/
- b = get_cmd640_reg(arttim_regs[index]) & ~0x3f;
+ b = get_cmd640_reg (arttim_regs[index]) & ~0x3f;
switch (b) {
- case 0x00: b = 4; break;
- case 0x80: b = 3; break;
- case 0x40: b = 2; break;
- default: b = 5; break;
+ case 0x00:
+ b = 4;
+ break;
+ case 0x80:
+ b = 3;
+ break;
+ case 0x40:
+ b = 2;
+ break;
+ default:
+ b = 5;
+ break;
}
setup_counts[index] = b;
/*
* Get the active/recovery counts
*/
- b = get_cmd640_reg(drwtim_regs[index]);
- active_counts[index] = (b >> 4) ? (b >> 4) : 0x10;
+ b = get_cmd640_reg (drwtim_regs[index]);
+ active_counts[index] = (b >> 4) ? (b >> 4) : 0x10;
recovery_counts[index] = (b & 0x0f) ? (b & 0x0f) : 0x10;
}
-
/*
* This routine writes the prepared setup/active/recovery counts
* for a drive into the cmd640 chipset registers to active them.
*/
-static void program_drive_counts (unsigned int index)
+static void
+program_drive_counts (ide_drive_t * drive, int setup_count, int
active_count,
+ int recovery_count)
{
unsigned long flags;
- u8 setup_count = setup_counts[index];
- u8 active_count = active_counts[index];
- u8 recovery_count = recovery_counts[index];
+ ide_drive_t *drives = HWIF (drive)->drives;
+ int channel = (int) HWIF (drive)->channel;
+ int index = calculate_index (drive);
/*
* Set up address setup count and drive read/write timing registers.
@@ -539,56 +555,87 @@
* each drive. Secondary interface has one common set of registers,
* so we merge the timings, using the slowest value for each timing.
*/
- if (index > 1) {
- unsigned int mate;
- if (cmd_drives[mate = index ^ 1]->present) {
- if (setup_count < setup_counts[mate])
- setup_count = setup_counts[mate];
- if (active_count < active_counts[mate])
- active_count = active_counts[mate];
- if (recovery_count < recovery_counts[mate])
- recovery_count = recovery_counts[mate];
- }
+ if (channel) {
+ drive->drive_data = setup_count;
+ setup_count = IDE_MAX (drives[0].drive_data,
+ drives[1].drive_data);
}
/*
- * Convert setup_count to internal chipset representation
+ * Convert values to internal chipset representation
*/
switch (setup_count) {
- case 4: setup_count = 0x00; break;
- case 3: setup_count = 0x80; break;
- case 1:
- case 2: setup_count = 0x40; break;
- default: setup_count = 0xc0; /* case 5 */
+ case 4:
+ setup_count = 0x00;
+ break;
+ case 3:
+ setup_count = 0x80;
+ break;
+ case 1:
+ case 2:
+ setup_count = 0x40;
+ break;
+ default:
+ setup_count = 0xc0; /* case 5 */
}
/*
* Now that everything is ready, program the new timings
*/
- spin_lock_irqsave(&ide_lock, flags);
+ spin_lock_irqsave (&ide_lock, flags);
/*
* Program the address_setup clocks into ARTTIM reg,
* and then the active/recovery counts into the DRWTIM reg
* (this converts counts of 16 into counts of zero -- okay).
*/
- setup_count |= __get_cmd640_reg(arttim_regs[index]) & 0x3f;
- __put_cmd640_reg(arttim_regs[index], setup_count);
- __put_cmd640_reg(drwtim_regs[index], pack_nibbles(active_count,
recovery_count));
- spin_unlock_irqrestore(&ide_lock, flags);
+ setup_count |= get_cmd640_reg (arttim_regs[index]) & 0x3f;
+ put_cmd640_reg (arttim_regs[index], setup_count);
+ put_cmd640_reg (drwtim_regs[index],
+ pack_nibbles (active_count, recovery_count));
+ spin_unlock_irqrestore (&ide_lock, flags);
}
/*
- * Set a specific pio_mode for a drive
+ * Drive PIO mode selection:
*/
-static void cmd640_set_mode (unsigned int index, u8 pio_mode, unsigned
int cycle_time)
+static void
+cmd640_tuneproc (ide_drive_t * drive, u8 mode_wanted)
{
- int setup_time, active_time, recovery_time, clock_time;
- u8 setup_count, active_count, recovery_count, recovery_count2,
cycle_count;
- int bus_speed = system_bus_clock();
+ int setup_time, active_time, recovery_time;
+ int clock_time, pio_mode, cycle_time;
+ u8 recovery_count2, cycle_count, b;
+ int setup_count, active_count, recovery_count;
+ int bus_speed = system_bus_clock ();
+ ide_pio_data_t d;
+
+ switch (mode_wanted) {
+ case 6: /* set fast-devsel off */
+ case 7: /* set fast-devsel on */
+ mode_wanted &= 1;
+ b = get_cmd640_reg (CNTRL) & ~0x27;
+ if (mode_wanted)
+ b |= 0x27;
+ put_cmd640_reg (CNTRL, b);
+ printk ("%s: %sabled cmd640 fast host timing (devsel)\n",
+ drive->name, mode_wanted ? "en" : "dis");
+ return;
+
+ case 8: /* set prefetch off */
+ case 9: /* set prefetch on */
+ mode_wanted &= 1;
+ set_prefetch_mode (drive, mode_wanted);
+ printk ("%s: %sabled cmd640 prefetch\n", drive->name,
+ mode_wanted ? "en" : "dis");
+ return;
+ }
+
+ mode_wanted = ide_get_best_pio_mode (drive, mode_wanted, 5, &d);
+ pio_mode = d.pio_mode;
+ cycle_time = d.cycle_time;
if (pio_mode > 5)
pio_mode = 5;
- setup_time = ide_pio_timings[pio_mode].setup_time;
+ setup_time = ide_pio_timings[pio_mode].setup_time;
active_time = ide_pio_timings[pio_mode].active_time;
recovery_time = cycle_time - (setup_time + active_time);
clock_time = 1000 / bus_speed;
@@ -598,158 +645,78 @@
active_count = (active_time + clock_time - 1) / clock_time;
if (active_count < 2)
- active_count = 2; /* minimum allowed by cmd640 */
+ active_count = 2; /* minimum allowed by cmd640 */
recovery_count = (recovery_time + clock_time - 1) / clock_time;
recovery_count2 = cycle_count - (setup_count + active_count);
if (recovery_count2 > recovery_count)
recovery_count = recovery_count2;
if (recovery_count < 2)
- recovery_count = 2; /* minimum allowed by cmd640 */
+ recovery_count = 2; /* minimum allowed by cmd640 */
if (recovery_count > 17) {
active_count += recovery_count - 17;
recovery_count = 17;
}
if (active_count > 16)
- active_count = 16; /* maximum allowed by cmd640 */
+ active_count = 16; /* maximum allowed by cmd640 */
if (cmd640_chip_version > 1)
- recovery_count -= 1; /* cmd640b uses (count + 1)*/
+ recovery_count -= 1; /* cmd640b uses (count + 1) */
if (recovery_count > 16)
- recovery_count = 16; /* maximum allowed by cmd640 */
-
- setup_counts[index] = setup_count;
- active_counts[index] = active_count;
- recovery_counts[index] = recovery_count;
+ recovery_count = 16; /* maximum allowed by cmd640 */
/*
* In a perfect world, we might set the drive pio mode here
* (using WIN_SETFEATURE) before continuing.
*
* But we do not, because:
- * 1) this is the wrong place to do it (proper is do_special() in
ide.c)
- * 2) in practice this is rarely, if ever, necessary
+ * 1) this is the wrong place to do it (proper is do_special()
in ide.c)
+ * 2) in practice this is rarely, if ever, necessary
*/
- program_drive_counts (index);
-}
-
-/*
- * Drive PIO mode selection:
- */
-static void cmd640_tune_drive (ide_drive_t *drive, u8 mode_wanted)
-{
- u8 b;
- ide_pio_data_t d;
- unsigned int index = 0;
-
- while (drive != cmd_drives[index]) {
- if (++index > 3) {
- printk("%s: bad news in cmd640_tune_drive\n", drive->name);
- return;
- }
- }
- switch (mode_wanted) {
- case 6: /* set fast-devsel off */
- case 7: /* set fast-devsel on */
- mode_wanted &= 1;
- b = get_cmd640_reg(CNTRL) & ~0x27;
- if (mode_wanted)
- b |= 0x27;
- put_cmd640_reg(CNTRL, b);
- printk("%s: %sabled cmd640 fast host timing (devsel)\n",
drive->name, mode_wanted ? "en" : "dis");
- return;
-
- case 8: /* set prefetch off */
- case 9: /* set prefetch on */
- mode_wanted &= 1;
- set_prefetch_mode(index, mode_wanted);
- printk("%s: %sabled cmd640 prefetch\n", drive->name, mode_wanted ?
"en" : "dis");
- return;
- }
-
- (void) ide_get_best_pio_mode (drive, mode_wanted, 5, &d);
- cmd640_set_mode (index, d.pio_mode, d.cycle_time);
+ program_drive_counts (drive, setup_count, active_count,
recovery_count);
- printk ("%s: selected cmd640 PIO mode%d (%dns)%s",
- drive->name,
- d.pio_mode,
- d.cycle_time,
- d.overridden ? " (overriding vendor mode)" : "");
- display_clocks(index);
- return;
+ printk ("%s: selected cmd640 PIO mode%d : %d (%dns)%s, "
+ "clocks=%d/%d/%d\n",
+ drive->name, pio_mode, mode_wanted, cycle_time,
+ d.overridden ? " (overriding vendor mode)" : "",
+ setup_count, active_count, recovery_count);
}
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
-
-static int pci_conf1(void)
+static void __init
+init_hwif_cmd640 (ide_hwif_t * hwif)
{
- u32 tmp;
- unsigned long flags;
-
- spin_lock_irqsave(&ide_lock, flags);
- outb(0x01, 0xCFB);
- tmp = inl(0xCF8);
- outl(0x80000000, 0xCF8);
- if (inl(0xCF8) == 0x80000000) {
- outl(tmp, 0xCF8);
- spin_unlock_irqrestore(&ide_lock, flags);
- return 1;
- }
- outl(tmp, 0xCF8);
- spin_unlock_irqrestore(&ide_lock, flags);
- return 0;
-}
-
-static int pci_conf2(void)
-{
- unsigned long flags;
-
- spin_lock_irqsave(&ide_lock, flags);
- outb(0x00, 0xCFB);
- outb(0x00, 0xCF8);
- outb(0x00, 0xCFA);
- if (inb(0xCF8) == 0x00 && inb(0xCF8) == 0x00) {
- spin_unlock_irqrestore(&ide_lock, flags);
- return 1;
- }
- spin_unlock_irqrestore(&ide_lock, flags);
- return 0;
-}
-
-/*
- * Probe for a cmd640 chipset, and initialize it if found. Called
from ide.c
- */
-static void __init ide_probe_for_cmd640x (void)
-{
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
int second_port_toggled = 0;
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
int second_port_cmd640 = 0;
const char *bus_type, *port2;
- unsigned int index;
u8 b, cfr;
+ int i;
+
+ hwif->tuneproc = &cmd640_tuneproc;
- if (cmd640_vlb && probe_for_cmd640_vlb()) {
+ if (cmd640_vlb && probe_for_cmd640_vlb ()) {
bus_type = "VLB";
} else {
cmd640_vlb = 0;
/* Find out what kind of PCI probing is supported otherwise
we break some Adaptec cards... */
- if (pci_conf1() && probe_for_cmd640_pci1())
+
+ if (probe_for_cmd640_pci1 ())
bus_type = "PCI (type1)";
- else if (pci_conf2() && probe_for_cmd640_pci2())
+ else if (probe_for_cmd640_pci2 ())
bus_type = "PCI (type2)";
else
return;
}
+
/*
* Undocumented magic (there is no 0x5b reg in specs)
*/
- put_cmd640_reg(0x5b, 0xbd);
- if (get_cmd640_reg(0x5b) != 0xbd) {
- printk(KERN_ERR "ide: cmd640 init failed: wrong value in reg
0x5b\n");
+ put_cmd640_reg (0x5b, 0xbd);
+ if (get_cmd640_reg (0x5b) != 0xbd) {
+ printk (KERN_ERR
+ "ide: cmd640 init failed: wrong value in reg 0x5b\n");
return;
}
- put_cmd640_reg(0x5b, 0);
+ put_cmd640_reg (0x5b, 0);
#ifdef CMD640_DUMP_REGS
CMD640_DUMP_REGS;
@@ -758,23 +725,18 @@
/*
* Documented magic begins here
*/
- cfr = get_cmd640_reg(CFR);
+ cfr = get_cmd640_reg (CFR);
cmd640_chip_version = cfr & CFR_DEVREV;
if (cmd640_chip_version == 0) {
printk ("ide: bad cmd640 revision: %d\n", cmd640_chip_version);
return;
}
- /*
- * Initialize data for primary port
- */
- setup_device_ptrs ();
- printk("%s: buggy cmd640%c interface on %s, config=0x%02x\n",
- cmd_hwif0->name, 'a' + cmd640_chip_version - 1, bus_type,
cfr);
- cmd_hwif0->chipset = ide_cmd640;
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
- cmd_hwif0->tuneproc = &cmd640_tune_drive;
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
+ printk ("%s: buggy cmd640%c interface on %s, config=0x%02x\n",
+ hwif->name, 'a' + cmd640_chip_version - 1, bus_type, cfr);
+
+ hwif->serialized = 1;
+ hwif->chipset = ide_cmd640;
/*
* Ensure compatibility by always using the slowest timings
@@ -783,121 +745,138 @@
*
* Maybe we need a way to NOT do these on *some* systems?
*/
- put_cmd640_reg(CMDTIM, 0);
- put_cmd640_reg(BRST, 0x40);
+ put_cmd640_reg (CMDTIM, 0);
+ put_cmd640_reg (BRST, 0x40);
/*
* Try to enable the secondary interface, if not already enabled
*/
- if (cmd_hwif1->noprobe) {
- port2 = "not probed";
- } else {
- b = get_cmd640_reg(CNTRL);
- if (secondary_port_responding()) {
- if ((b & CNTRL_ENA_2ND)) {
- second_port_cmd640 = 1;
- port2 = "okay";
- } else if (cmd640_vlb) {
- second_port_cmd640 = 1;
- port2 = "alive";
- } else
- port2 = "not cmd640";
+ if (hwif->channel == 1) //secondary interface
+ {
+ if (hwif->noprobe) {
+ port2 = "not probed";
} else {
- put_cmd640_reg(CNTRL, b ^ CNTRL_ENA_2ND); /* toggle the bit */
- if (secondary_port_responding()) {
- second_port_cmd640 = 1;
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
- second_port_toggled = 1;
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
- port2 = "enabled";
+ b = get_cmd640_reg (CNTRL);
+ if (secondary_port_responding ()) {
+ if ((b & CNTRL_ENA_2ND)) {
+ second_port_cmd640 = 1;
+ port2 = "okay";
+ } else if (cmd640_vlb) {
+ second_port_cmd640 = 1;
+ port2 = "alive";
+ } else
+ port2 = "not cmd640";
} else {
- put_cmd640_reg(CNTRL, b); /* restore original setting */
- port2 = "not responding";
+ put_cmd640_reg (CNTRL, b ^ CNTRL_ENA_2ND); /* toggle the bit */
+ if (secondary_port_responding ()) {
+ second_port_cmd640 = 1;
+ second_port_toggled = 1;
+ port2 = "enabled";
+ } else {
+ put_cmd640_reg (CNTRL, b); /* restore original setting */
+ port2 = "not responding";
+ }
}
}
- }
- /*
- * Initialize data for secondary cmd640 port, if enabled
- */
- if (second_port_cmd640) {
- cmd_hwif0->serialized = 1;
- cmd_hwif1->serialized = 1;
- cmd_hwif1->chipset = ide_cmd640;
- cmd_hwif0->mate = cmd_hwif1;
- cmd_hwif1->mate = cmd_hwif0;
- cmd_hwif1->channel = 1;
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
- cmd_hwif1->tuneproc = &cmd640_tune_drive;
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
+ /*
+ * Initialize data for secondary cmd640 port, if enabled
+ */
+ printk (KERN_INFO "%s: %sserialized, secondary interface %s\n",
+ hwif->name, hwif->serialized ? "" : "not ", port2);
}
- printk(KERN_INFO "%s: %sserialized, secondary interface %s\n",
cmd_hwif1->name,
- cmd_hwif0->serialized ? "" : "not ", port2);
/*
* Establish initial timings/prefetch for all drives.
* Do not unnecessarily disturb any prior BIOS setup of these.
*/
- for (index = 0; index < (2 + (second_port_cmd640 << 1)); index++) {
- ide_drive_t *drive = cmd_drives[index];
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
- if (drive->autotune || ((index > 1) && second_port_toggled)) {
- /*
- * Reset timing to the slowest speed and turn off prefetch.
+ for (i = 0; i < 2; i++) {
+ if (hwif->drives[i].autotune) {
+ /*
+ * Reset timing to the slowest speed and turn off prefetch.
* This way, the drive identify code has a better chance.
*/
- setup_counts [index] = 4; /* max possible */
- active_counts [index] = 16; /* max possible */
- recovery_counts [index] = 16; /* max possible */
- program_drive_counts (index);
- set_prefetch_mode (index, 0);
- printk("cmd640: drive%d timings/prefetch cleared\n", index);
+ setup_counts[2 * hwif->channel + i] = 4; /* max possible */
+ active_counts[2 * hwif->channel + i] = 16; /* max possible */
+ recovery_counts[2 * hwif->channel + i] = 16; /* max possible */
+ program_drive_counts (&(hwif->drives[i]), 4, 16, 16);
+ set_prefetch_mode ((&hwif->drives[i]), 0);
+ printk ("cmd640: drive%d timings/prefetch cleared\n",
+ 2 * hwif->channel + i);
} else {
/*
* Record timings/prefetch without changing them.
* This preserves any prior BIOS setup.
*/
- retrieve_drive_counts (index);
- check_prefetch (index);
- printk("cmd640: drive%d timings/prefetch(%s) preserved",
- index, drive->no_io_32bit ? "off" : "on");
- display_clocks(index);
+ retrieve_drive_counts (&hwif->drives[i]);
+ check_prefetch (&hwif->drives[i]);
+ printk
+ ("cmd640: drive%d timings/prefetch(%s) preserved",
+ 2 * hwif->channel + i,
+ hwif->drives[i].no_io_32bit ? "off" : "on");
+ display_clocks (&hwif->drives[i]);
}
-#else
- /*
- * Set the drive unmask flags to match the prefetch setting
- */
- check_prefetch (index);
- printk("cmd640: drive%d timings/prefetch(%s) preserved\n",
- index, drive->no_io_32bit ? "off" : "on");
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
}
#ifdef CMD640_DUMP_REGS
CMD640_DUMP_REGS;
#endif
- return;
-}
-
-static int __init cmd640_init(void)
-{
- ide_register_driver(ide_probe_for_cmd640x);
- return 0;
}
/*
* Called by the IDE core when compiled in and cmd640=vlb is
* selected.
*/
-void init_cmd640_vlb(void)
+void __init
+init_cmd640_vlb (void)
{
cmd640_vlb = 1;
}
-module_init(cmd640_init);
+extern void ide_setup_pci_device (struct pci_dev *, ide_pci_device_t
*);
+
+static int __devinit
+cmd640_init_one (struct pci_dev *dev, const struct pci_device_id *id)
+{
+ ide_pci_device_t *d = &cmd640_chipsets[id->driver_data];
+ if (dev->device != d->device)
+ BUG ();
+ ide_setup_pci_device (dev, d);
+ MOD_INC_USE_COUNT;
+ return 0;
+}
+
+static struct pci_device_id cmd640_pci_tbl[] __devinitdata = {
+ {PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_640, PCI_ANY_ID, PCI_ANY_ID, 0,
0,
+ 0},
+ {0,},
+};
+
+static struct pci_driver driver = {
+ .name = "CMD640 IDE",
+ .id_table = cmd640_pci_tbl,
+ .probe = cmd640_init_one,
+};
+
+static int __init
+cmd640_ide_init (void)
+{
+ return ide_pci_register_driver (&driver);
+}
+
+static void __exit
+cmd640_ide_exit (void)
+{
+ ide_pci_unregister_driver (&driver);
+}
+
+module_init (cmd640_ide_init);
+module_exit (cmd640_ide_exit);
+
+MODULE_AUTHOR ("Igor Abramov, Mark Lord, Stefan Talpalaru");
+MODULE_DESCRIPTION ("IDE support for CMD640 controller");
+MODULE_PARM (cmd640_vlb, "i");
+MODULE_PARM_DESC (cmd640_vlb, "Set to enable scanning for VLB
controllers");
+MODULE_LICENSE ("GPL");
-MODULE_AUTHOR("See Source");
-MODULE_DESCRIPTION("IDE support for CMD640 controller");
-MODULE_PARM(cmd640_vlb, "i");
-MODULE_PARM_DESC(cmd640_vlb, "Set to enable scanning for VLB
controllers");
-MODULE_LICENSE("GPL");
+EXPORT_NO_SYMBOLS;
diff -urN linux-2.4.22/drivers/ide/pci/cmd640.h
linux-2.4.22-new/drivers/ide/pci/cmd640.h
--- linux-2.4.22/drivers/ide/pci/cmd640.h 2003-09-10 17:18:22.000000000
+0000
+++ linux-2.4.22-new/drivers/ide/pci/cmd640.h 2003-10-26
17:07:10.000000000 +0000
@@ -5,28 +5,28 @@
#include <linux/pci.h>
#include <linux/ide.h>
-#define IDE_IGNORE ((void *)-1)
+static void init_hwif_cmd640 (ide_hwif_t *);
-static ide_pci_device_t cmd640_chipsets[] __initdata = {
+static ide_pci_device_t cmd640_chipsets[] __devinitdata = {
{
- .vendor = PCI_VENDOR_ID_CMD,
- .device = PCI_DEVICE_ID_CMD_640,
- .name = "CMD640",
- .init_setup = NULL,
- .init_chipset = NULL,
- .init_iops = NULL,
- .init_hwif = IDE_IGNORE,
- .init_dma = NULL,
- .channels = 2,
- .autodma = NODMA,
- .enablebits = {{0x00,0x00,0x00}, {0x00,0x00,0x00}},
- .bootable = ON_BOARD,
- .extra = 0
- },{
- .vendor = 0,
- .device = 0,
- .bootable = EOL,
- }
-}
+ .vendor = PCI_VENDOR_ID_CMD,
+ .device = PCI_DEVICE_ID_CMD_640,
+ .name = "CMD640",
+ .init_setup = NULL,
+ .init_chipset = NULL,
+ .init_iops = NULL,
+ .init_hwif = init_hwif_cmd640,
+ .init_dma = NULL,
+ .channels = 2,
+ .autodma = NODMA,
+ .enablebits = {{0x00, 0x00, 0x00}, {0x00, 0x00, 0x00}},
+ .bootable = ON_BOARD,
+ .extra = 0}, {
+ .vendor = 0,
+ .device = 0,
+ .channels = 0,
+ .bootable = EOL,
+ }
+};
-#endif /* CMD640_H */
+#endif /* CMD640_H */
=====
Stefan Talpalaru
__________________________________
Do you Yahoo!?
Exclusive Video Premiere - Britney Spears
http://launch.yahoo.com/promos/britneyspears/
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: CMD640 ide driver made to work
2003-10-27 12:26 CMD640 ide driver made to work Stefan Talpalaru
@ 2003-10-27 14:35 ` Bartlomiej Zolnierkiewicz
2003-10-29 12:12 ` PATCH: CMD640 IDE chipset Stefan Talpalaru
0 siblings, 1 reply; 10+ messages in thread
From: Bartlomiej Zolnierkiewicz @ 2003-10-27 14:35 UTC (permalink / raw)
To: Stefan Talpalaru, andre; +Cc: linux-kernel
Hi,
Can you please drop all code-style changes (such as foo() -> foo ())
from your patch and describe what real changes you've done?
Also please fix your mailer, it breaks lines.
BTW Andre is no longer maintaing IDE, cc: me instead, thanks.
cheers,
--bartlomiej
On Monday 27 of October 2003 13:26, Stefan Talpalaru wrote:
> Hi Andre!
>
> I own an old 486 box with a CMD640 chipset on it. It works just fine under
> the 2.2.x kernel, but not under the 2.4.x series. I modified the "cmd640"
> driver so it works and I have tested it on my hardware.
> This patch is for the 2.4.22 kernel.
^ permalink raw reply [flat|nested] 10+ messages in thread
* PATCH: CMD640 IDE chipset
2003-10-27 14:35 ` Bartlomiej Zolnierkiewicz
@ 2003-10-29 12:12 ` Stefan Talpalaru
2003-10-29 12:48 ` Alexander Atanasov
2003-10-29 19:36 ` Bartlomiej Zolnierkiewicz
0 siblings, 2 replies; 10+ messages in thread
From: Stefan Talpalaru @ 2003-10-29 12:12 UTC (permalink / raw)
To: Bartlomiej Zolnierkiewicz; +Cc: linux-kernel
[-- Attachment #1: Type: text/plain, Size: 1925 bytes --]
Hi Bartolomiej!
--- Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> wrote:
>
> Hi,
>
> Can you please drop all code-style changes (such as foo() -> foo ())
sorry about that, I ran Lindent on it...
> from your patch and describe what real changes you've done?
> Also please fix your mailer, it breaks lines.
>
> BTW Andre is no longer maintaing IDE, cc: me instead, thanks.
>
> cheers,
> --bartlomiej
Please excuse me for sending this patch as an attachment,
but as my mail account is Yahoo! and I'm too lazy to find a better
sollution, I cannot get the patch through the web interface without
breaking the lines.
This patch integrates the CMD640 chipset support in the 2.4.22
kernel. I was using it succesfully in the 2.2.x kernel series, but
got no result in the 2.4.x kernels. After comparing the 2 versions,
I noticed errors in the new version (outb_p() instead of outl_p())
and also some useless code (the wrapers: __put_cmd640_reg() and
__get_cmd640_reg() - which I removed and placed the locks where needed;
the pci_conf1() and pci_conf2() functions).
I also removed the CONFIG_BLK_DEV_CMD640_ENHANCED config option, as
it
makes little difference for the kernel size.
The init_hwif_cmd640() function had to be rewritten because it is
called once for each ide interface found, so the old way of addressing
all the drives in one run was no longer working. Therefore, to not
break all the code, came the need for a function that computes the
index from the ide_drive_t* : calculate_index().
The code that handles PIO settings was rearanged in a new function:
cmd640_tuneproc().
To end the description, I brought back to live a piece of dead code
just because I needed to use both ide interfaces on my old 486 board.
later.
=====
Stefan Talpalaru
__________________________________
Do you Yahoo!?
Exclusive Video Premiere - Britney Spears
http://launch.yahoo.com/promos/britneyspears/
[-- Attachment #2: diff.cmd640 --]
[-- Type: application/octet-stream, Size: 25836 bytes --]
diff -urN linux-2.4.22/Documentation/Configure.help linux-2.4.22-new/Documentation/Configure.help
--- linux-2.4.22/Documentation/Configure.help 2003-09-10 17:39:41.000000000 +0000
+++ linux-2.4.22-new/Documentation/Configure.help 2003-10-26 14:14:12.000000000 +0000
@@ -916,14 +916,6 @@
the "CSA-6400E PCI to IDE controller" that some people have. For
details, read <file:Documentation/ide.txt>.
-CMD640 enhanced support
-CONFIG_BLK_DEV_CMD640_ENHANCED
- This option includes support for setting/autotuning PIO modes and
- prefetch on CMD640 IDE interfaces. For details, read
- <file:Documentation/ide.txt>. If you have a CMD640 IDE interface
- and your BIOS does not already do this for you, then say Y here.
- Otherwise say N.
-
RZ1000 chipset bugfix/support
CONFIG_BLK_DEV_RZ1000
The PC-Technologies RZ1000 IDE chip is used on many common 486 and
diff -urN linux-2.4.22/drivers/ide/Config.in linux-2.4.22-new/drivers/ide/Config.in
--- linux-2.4.22/drivers/ide/Config.in 2003-09-10 17:49:50.000000000 +0000
+++ linux-2.4.22-new/drivers/ide/Config.in 2003-10-18 21:43:37.000000000 +0000
@@ -28,7 +28,6 @@
comment 'IDE chipset support/bugfixes'
if [ "$CONFIG_BLK_DEV_IDE" != "n" ]; then
dep_bool ' CMD640 chipset bugfix/support' CONFIG_BLK_DEV_CMD640 $CONFIG_X86
- dep_bool ' CMD640 enhanced support' CONFIG_BLK_DEV_CMD640_ENHANCED $CONFIG_BLK_DEV_CMD640
dep_bool ' ISA-PNP EIDE support' CONFIG_BLK_DEV_ISAPNP $CONFIG_ISAPNP
if [ "$CONFIG_PCI" = "y" ]; then
bool ' PCI IDE chipset support' CONFIG_BLK_DEV_IDEPCI
diff -urN linux-2.4.22/drivers/ide/pci/cmd640.c linux-2.4.22-new/drivers/ide/pci/cmd640.c
--- linux-2.4.22/drivers/ide/pci/cmd640.c 2003-09-10 17:49:55.000000000 +0000
+++ linux-2.4.22-new/drivers/ide/pci/cmd640.c 2003-10-27 23:33:53.000000000 +0000
@@ -1,12 +1,14 @@
/*
- * linux/drivers/ide/pci/cmd640.c Version 1.02 Sep 01, 1996
+ * linux/drivers/ide/pci/cmd640.c Version 2.00 Oct 26, 2003
*
- * Copyright (C) 1995-1996 Linus Torvalds & authors (see below)
+ * Copyright (C) 1995-2003 Linus Torvalds & authors (see below)
*/
/*
* Original authors: abramov@cecmow.enet.dec.com (Igor Abramov)
* mlord@pobox.com (Mark Lord)
+ * The guy that made it work in the 2.4.x kernel:
+ * stefantalpalaru@yahoo.com (Stefan Talpalaru)
*
* See linux/MAINTAINERS for address of current maintainer.
*
@@ -96,6 +98,8 @@
* ("fast" is necessary for 32bit I/O in some systems)
* Version 1.02 fix bug that resulted in slow "setup times"
* (patch courtesy of Zoltan Hidvegi)
+ * Version 2.00 it seems that this driver never worked in the 2.4.x
+ * kernel series. This version fixes this problem.
*/
#undef REALLY_SLOW_IO /* most systems can safely undef this */
@@ -113,10 +117,10 @@
#include <linux/hdreg.h>
#include <linux/ide.h>
#include <linux/init.h>
-
#include <asm/io.h>
#include "ide_modes.h"
+#include "cmd640.h"
/*
* This flag is set in ide.c by the parameter: ide0=cmd640_vlb
@@ -173,9 +177,6 @@
*/
static u8 prefetch_regs[4] = {CNTRL, CNTRL, ARTTIM23, ARTTIM23};
static u8 prefetch_masks[4] = {CNTRL_DIS_RA0, CNTRL_DIS_RA1, ARTTIM23_DIS_RA2, ARTTIM23_DIS_RA3};
-
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
-
static u8 arttim_regs[4] = {ARTTIM0, ARTTIM1, ARTTIM23, ARTTIM23};
static u8 drwtim_regs[4] = {DRWTIM0, DRWTIM1, DRWTIM23, DRWTIM23};
@@ -187,26 +188,28 @@
static u8 active_counts[4] = {16, 16, 16, 16}; /* Active count (encoded) */
static u8 recovery_counts[4] = {16, 16, 16, 16}; /* Recovery count (encoded) */
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
-
-/*
- * These are initialized to point at the devices we control
- */
-static ide_hwif_t *cmd_hwif0, *cmd_hwif1;
-static ide_drive_t *cmd_drives[4];
-
/*
* Interface to access cmd640x registers
*/
static unsigned int cmd640_key;
-static void (*__put_cmd640_reg)(u16 reg, u8 val);
-static u8 (*__get_cmd640_reg)(u16 reg);
+static void (*put_cmd640_reg) (u16 reg, u8 val);
+static u8 (*get_cmd640_reg) (u16 reg);
/*
* This is read from the CFR reg, and is used in several places.
*/
static unsigned int cmd640_chip_version;
+static inline int
+calculate_index (ide_drive_t * drive)
+{
+ ide_hwif_t *hwif = HWIF (drive);
+ int channel = (int) hwif->channel;
+ int slave = (hwif->drives != drive);
+
+ return 2 * channel + slave;
+}
+
/*
* The CMD640x chip does not support DWORD config write cycles, but some
* of the BIOSes use them to implement the config services.
@@ -217,32 +220,49 @@
static void put_cmd640_reg_pci1 (u16 reg, u8 val)
{
- outb_p((reg & 0xfc) | cmd640_key, 0xcf8);
+ unsigned long flags;
+
+ spin_lock_irqsave (&ide_lock, flags);
+ outl_p((reg & 0xfc) | cmd640_key, 0xcf8);
outb_p(val, (reg & 3) | 0xcfc);
+ spin_unlock_irqrestore (&ide_lock, flags);
}
static u8 get_cmd640_reg_pci1 (u16 reg)
{
- outb_p((reg & 0xfc) | cmd640_key, 0xcf8);
- return inb_p((reg & 3) | 0xcfc);
+ u8 b;
+ unsigned long flags;
+
+ spin_lock_irqsave (&ide_lock, flags);
+ outl_p ((reg & 0xfc) | cmd640_key, 0xcf8);
+ b = inb_p ((reg & 3) | 0xcfc);
+ spin_unlock_irqrestore (&ide_lock, flags);
+ return b;
}
/* PCI method 2 access (from CMD datasheet) */
static void put_cmd640_reg_pci2 (u16 reg, u8 val)
{
+ unsigned long flags;
+
+ spin_lock_irqsave (&ide_lock, flags);
outb_p(0x10, 0xcf8);
outb_p(val, cmd640_key + reg);
outb_p(0, 0xcf8);
+ spin_unlock_irqrestore (&ide_lock, flags);
}
static u8 get_cmd640_reg_pci2 (u16 reg)
{
u8 b;
+ unsigned long flags;
+ spin_lock_irqsave (&ide_lock, flags);
outb_p(0x10, 0xcf8);
b = inb_p(cmd640_key + reg);
outb_p(0, 0xcf8);
+ spin_unlock_irqrestore (&ide_lock, flags);
return b;
}
@@ -250,36 +270,26 @@
static void put_cmd640_reg_vlb (u16 reg, u8 val)
{
+ unsigned long flags;
+
+ spin_lock_irqsave(&ide_lock, flags);
outb_p(reg, cmd640_key);
outb_p(val, cmd640_key + 4);
+ spin_unlock_irqrestore(&ide_lock, flags);
}
static u8 get_cmd640_reg_vlb (u16 reg)
{
- outb_p(reg, cmd640_key);
- return inb_p(cmd640_key + 4);
-}
-
-static u8 get_cmd640_reg(u16 reg)
-{
u8 b;
unsigned long flags;
spin_lock_irqsave(&ide_lock, flags);
- b = __get_cmd640_reg(reg);
+ outb_p(reg, cmd640_key);
+ b = inb_p(cmd640_key + 4);
spin_unlock_irqrestore(&ide_lock, flags);
return b;
}
-static void put_cmd640_reg(u16 reg, u8 val)
-{
- unsigned long flags;
-
- spin_lock_irqsave(&ide_lock, flags);
- __put_cmd640_reg(reg,val);
- spin_unlock_irqrestore(&ide_lock, flags);
-}
-
static int __init match_pci_cmd640_device (void)
{
const u8 ven_dev[4] = {0x95, 0x10, 0x40, 0x06};
@@ -302,8 +312,8 @@
*/
static int __init probe_for_cmd640_pci1 (void)
{
- __get_cmd640_reg = get_cmd640_reg_pci1;
- __put_cmd640_reg = put_cmd640_reg_pci1;
+ get_cmd640_reg = get_cmd640_reg_pci1;
+ put_cmd640_reg = put_cmd640_reg_pci1;
for (cmd640_key = 0x80000000;
cmd640_key <= 0x8000f800;
cmd640_key += 0x800) {
@@ -318,8 +328,8 @@
*/
static int __init probe_for_cmd640_pci2 (void)
{
- __get_cmd640_reg = get_cmd640_reg_pci2;
- __put_cmd640_reg = put_cmd640_reg_pci2;
+ get_cmd640_reg = get_cmd640_reg_pci2;
+ put_cmd640_reg = put_cmd640_reg_pci2;
for (cmd640_key = 0xc000; cmd640_key <= 0xcf00; cmd640_key += 0x100) {
if (match_pci_cmd640_device())
return 1; /* success */
@@ -334,8 +344,8 @@
{
u8 b;
- __get_cmd640_reg = get_cmd640_reg_vlb;
- __put_cmd640_reg = put_cmd640_reg_vlb;
+ get_cmd640_reg = get_cmd640_reg_vlb;
+ put_cmd640_reg = put_cmd640_reg_vlb;
cmd640_key = 0x178;
b = get_cmd640_reg(CFR);
if (b == 0xff || b == 0x00 || (b & CFR_AT_VESA_078h)) {
@@ -375,7 +385,7 @@
/*
* Dump out all cmd640 registers. May be called from ide.c
*/
-static void cmd640_dump_regs (void)
+static void __init cmd640_dump_regs (void)
{
unsigned int reg = cmd640_vlb ? 0x50 : 0x00;
@@ -394,9 +404,9 @@
* Check whether prefetch is on for a drive,
* and initialize the unmask flags for safe operation.
*/
-static void __init check_prefetch (unsigned int index)
+static void __init check_prefetch (ide_drive_t * drive)
{
- ide_drive_t *drive = cmd_drives[index];
+ int index = calculate_index (drive);
u8 b = get_cmd640_reg(prefetch_regs[index]);
if (b & prefetch_masks[index]) { /* is prefetch off? */
@@ -413,43 +423,17 @@
}
/*
- * Figure out which devices we control
- */
-static void __init setup_device_ptrs (void)
-{
- unsigned int i;
-
- cmd_hwif0 = &ide_hwifs[0]; /* default, if not found below */
- cmd_hwif1 = &ide_hwifs[1]; /* default, if not found below */
- for (i = 0; i < MAX_HWIFS; i++) {
- ide_hwif_t *hwif = &ide_hwifs[i];
- if (hwif->chipset == ide_unknown || hwif->chipset == ide_generic) {
- if (hwif->io_ports[IDE_DATA_OFFSET] == 0x1f0)
- cmd_hwif0 = hwif;
- else if (hwif->io_ports[IDE_DATA_OFFSET] == 0x170)
- cmd_hwif1 = hwif;
- }
- }
- cmd_drives[0] = &cmd_hwif0->drives[0];
- cmd_drives[1] = &cmd_hwif0->drives[1];
- cmd_drives[2] = &cmd_hwif1->drives[0];
- cmd_drives[3] = &cmd_hwif1->drives[1];
-}
-
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
-
-/*
* Sets prefetch mode for a drive.
*/
-static void set_prefetch_mode (unsigned int index, int mode)
+static void set_prefetch_mode (ide_drive_t * drive, int mode)
{
- ide_drive_t *drive = cmd_drives[index];
+ int index = calculate_index (drive);
int reg = prefetch_regs[index];
u8 b;
unsigned long flags;
spin_lock_irqsave(&ide_lock, flags);
- b = __get_cmd640_reg(reg);
+ b = get_cmd640_reg(reg);
if (mode) { /* want prefetch on? */
#if CMD640_PREFETCH_MASKS
drive->no_unmask = 1;
@@ -463,15 +447,16 @@
drive->io_32bit = 0;
b |= prefetch_masks[index]; /* disable prefetch */
}
- __put_cmd640_reg(reg, b);
+ put_cmd640_reg(reg, b);
spin_unlock_irqrestore(&ide_lock, flags);
}
/*
* Dump out current drive clocks settings
*/
-static void display_clocks (unsigned int index)
+static void __init display_clocks (ide_drive_t * drive)
{
+ int index = calculate_index (drive);
u8 active_count, recovery_count;
active_count = active_counts[index];
@@ -481,7 +466,7 @@
if (active_count > 3 && recovery_count == 1)
++recovery_count;
if (cmd640_chip_version > 1)
- recovery_count += 1; /* cmd640b uses (count + 1)*/
+ recovery_count += 1; /* cmd640b uses (count + 1) */
printk(", clocks=%d/%d/%d\n", setup_counts[index], active_count, recovery_count);
}
@@ -497,8 +482,9 @@
/*
* This routine retrieves the initial drive timings from the chipset.
*/
-static void __init retrieve_drive_counts (unsigned int index)
+static void __init retrieve_drive_counts (ide_drive_t * drive)
{
+ int index = calculate_index (drive);
u8 b;
/*
@@ -521,17 +507,16 @@
recovery_counts[index] = (b & 0x0f) ? (b & 0x0f) : 0x10;
}
-
/*
* This routine writes the prepared setup/active/recovery counts
* for a drive into the cmd640 chipset registers to active them.
*/
-static void program_drive_counts (unsigned int index)
+static void program_drive_counts (ide_drive_t * drive, int setup_count, int active_count, int recovery_count)
{
unsigned long flags;
- u8 setup_count = setup_counts[index];
- u8 active_count = active_counts[index];
- u8 recovery_count = recovery_counts[index];
+ ide_drive_t *drives = HWIF (drive)->drives;
+ int channel = (int) HWIF (drive)->channel;
+ int index = calculate_index (drive);
/*
* Set up address setup count and drive read/write timing registers.
@@ -539,20 +524,14 @@
* each drive. Secondary interface has one common set of registers,
* so we merge the timings, using the slowest value for each timing.
*/
- if (index > 1) {
- unsigned int mate;
- if (cmd_drives[mate = index ^ 1]->present) {
- if (setup_count < setup_counts[mate])
- setup_count = setup_counts[mate];
- if (active_count < active_counts[mate])
- active_count = active_counts[mate];
- if (recovery_count < recovery_counts[mate])
- recovery_count = recovery_counts[mate];
- }
+ if (channel) {
+ drive->drive_data = setup_count;
+ setup_count = IDE_MAX (drives[0].drive_data,
+ drives[1].drive_data);
}
/*
- * Convert setup_count to internal chipset representation
+ * Convert values to internal chipset representation
*/
switch (setup_count) {
case 4: setup_count = 0x00; break;
@@ -571,24 +550,51 @@
* and then the active/recovery counts into the DRWTIM reg
* (this converts counts of 16 into counts of zero -- okay).
*/
- setup_count |= __get_cmd640_reg(arttim_regs[index]) & 0x3f;
- __put_cmd640_reg(arttim_regs[index], setup_count);
- __put_cmd640_reg(drwtim_regs[index], pack_nibbles(active_count, recovery_count));
+ setup_count |= get_cmd640_reg(arttim_regs[index]) & 0x3f;
+ put_cmd640_reg(arttim_regs[index], setup_count);
+ put_cmd640_reg(drwtim_regs[index], pack_nibbles(active_count, recovery_count));
spin_unlock_irqrestore(&ide_lock, flags);
}
/*
- * Set a specific pio_mode for a drive
+ * Drive PIO mode selection:
*/
-static void cmd640_set_mode (unsigned int index, u8 pio_mode, unsigned int cycle_time)
+static void
+cmd640_tuneproc (ide_drive_t * drive, u8 mode_wanted)
{
- int setup_time, active_time, recovery_time, clock_time;
- u8 setup_count, active_count, recovery_count, recovery_count2, cycle_count;
+ int setup_time, active_time, recovery_time;
+ int clock_time, pio_mode, cycle_time;
+ u8 recovery_count2, cycle_count, b;
+ int setup_count, active_count, recovery_count;
int bus_speed = system_bus_clock();
+ ide_pio_data_t d;
+
+ switch (mode_wanted) {
+ case 6: /* set fast-devsel off */
+ case 7: /* set fast-devsel on */
+ mode_wanted &= 1;
+ b = get_cmd640_reg(CNTRL) & ~0x27;
+ if (mode_wanted)
+ b |= 0x27;
+ put_cmd640_reg(CNTRL, b);
+ printk("%s: %sabled cmd640 fast host timing (devsel)\n", drive->name, mode_wanted ? "en" : "dis");
+ return;
+
+ case 8: /* set prefetch off */
+ case 9: /* set prefetch on */
+ mode_wanted &= 1;
+ set_prefetch_mode (drive, mode_wanted);
+ printk ("%s: %sabled cmd640 prefetch\n", drive->name, mode_wanted ? "en" : "dis");
+ return;
+ }
+
+ mode_wanted = ide_get_best_pio_mode(drive, mode_wanted, 5, &d);
+ pio_mode = d.pio_mode;
+ cycle_time = d.cycle_time;
if (pio_mode > 5)
pio_mode = 5;
- setup_time = ide_pio_timings[pio_mode].setup_time;
+ setup_time = ide_pio_timings[pio_mode].setup_time;
active_time = ide_pio_timings[pio_mode].active_time;
recovery_time = cycle_time - (setup_time + active_time);
clock_time = 1000 / bus_speed;
@@ -617,116 +623,32 @@
if (recovery_count > 16)
recovery_count = 16; /* maximum allowed by cmd640 */
- setup_counts[index] = setup_count;
- active_counts[index] = active_count;
- recovery_counts[index] = recovery_count;
-
/*
* In a perfect world, we might set the drive pio mode here
* (using WIN_SETFEATURE) before continuing.
*
* But we do not, because:
- * 1) this is the wrong place to do it (proper is do_special() in ide.c)
+ * 1) this is the wrong place to do it (proper is do_special() in ide.c)
* 2) in practice this is rarely, if ever, necessary
*/
- program_drive_counts (index);
-}
-
-/*
- * Drive PIO mode selection:
- */
-static void cmd640_tune_drive (ide_drive_t *drive, u8 mode_wanted)
-{
- u8 b;
- ide_pio_data_t d;
- unsigned int index = 0;
+ program_drive_counts (drive, setup_count, active_count, recovery_count);
- while (drive != cmd_drives[index]) {
- if (++index > 3) {
- printk("%s: bad news in cmd640_tune_drive\n", drive->name);
- return;
- }
- }
- switch (mode_wanted) {
- case 6: /* set fast-devsel off */
- case 7: /* set fast-devsel on */
- mode_wanted &= 1;
- b = get_cmd640_reg(CNTRL) & ~0x27;
- if (mode_wanted)
- b |= 0x27;
- put_cmd640_reg(CNTRL, b);
- printk("%s: %sabled cmd640 fast host timing (devsel)\n", drive->name, mode_wanted ? "en" : "dis");
- return;
-
- case 8: /* set prefetch off */
- case 9: /* set prefetch on */
- mode_wanted &= 1;
- set_prefetch_mode(index, mode_wanted);
- printk("%s: %sabled cmd640 prefetch\n", drive->name, mode_wanted ? "en" : "dis");
- return;
- }
-
- (void) ide_get_best_pio_mode (drive, mode_wanted, 5, &d);
- cmd640_set_mode (index, d.pio_mode, d.cycle_time);
-
- printk ("%s: selected cmd640 PIO mode%d (%dns)%s",
- drive->name,
- d.pio_mode,
- d.cycle_time,
- d.overridden ? " (overriding vendor mode)" : "");
- display_clocks(index);
- return;
-}
-
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
-
-static int pci_conf1(void)
-{
- u32 tmp;
- unsigned long flags;
-
- spin_lock_irqsave(&ide_lock, flags);
- outb(0x01, 0xCFB);
- tmp = inl(0xCF8);
- outl(0x80000000, 0xCF8);
- if (inl(0xCF8) == 0x80000000) {
- outl(tmp, 0xCF8);
- spin_unlock_irqrestore(&ide_lock, flags);
- return 1;
- }
- outl(tmp, 0xCF8);
- spin_unlock_irqrestore(&ide_lock, flags);
- return 0;
+ printk("%s: selected cmd640 PIO mode%d : %d (%dns)%s, "
+ "clocks=%d/%d/%d\n",
+ drive->name, pio_mode, mode_wanted, cycle_time,
+ d.overridden ? " (overriding vendor mode)" : "",
+ setup_count, active_count, recovery_count);
}
-static int pci_conf2(void)
+static void __init init_hwif_cmd640 (ide_hwif_t * hwif)
{
- unsigned long flags;
-
- spin_lock_irqsave(&ide_lock, flags);
- outb(0x00, 0xCFB);
- outb(0x00, 0xCF8);
- outb(0x00, 0xCFA);
- if (inb(0xCF8) == 0x00 && inb(0xCF8) == 0x00) {
- spin_unlock_irqrestore(&ide_lock, flags);
- return 1;
- }
- spin_unlock_irqrestore(&ide_lock, flags);
- return 0;
-}
-
-/*
- * Probe for a cmd640 chipset, and initialize it if found. Called from ide.c
- */
-static void __init ide_probe_for_cmd640x (void)
-{
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
int second_port_toggled = 0;
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
int second_port_cmd640 = 0;
const char *bus_type, *port2;
- unsigned int index;
u8 b, cfr;
+ int i;
+
+ hwif->tuneproc = &cmd640_tuneproc;
if (cmd640_vlb && probe_for_cmd640_vlb()) {
bus_type = "VLB";
@@ -734,13 +656,15 @@
cmd640_vlb = 0;
/* Find out what kind of PCI probing is supported otherwise
we break some Adaptec cards... */
- if (pci_conf1() && probe_for_cmd640_pci1())
+
+ if (probe_for_cmd640_pci1())
bus_type = "PCI (type1)";
- else if (pci_conf2() && probe_for_cmd640_pci2())
+ else if (probe_for_cmd640_pci2())
bus_type = "PCI (type2)";
else
return;
}
+
/*
* Undocumented magic (there is no 0x5b reg in specs)
*/
@@ -765,16 +689,11 @@
return;
}
- /*
- * Initialize data for primary port
- */
- setup_device_ptrs ();
printk("%s: buggy cmd640%c interface on %s, config=0x%02x\n",
- cmd_hwif0->name, 'a' + cmd640_chip_version - 1, bus_type, cfr);
- cmd_hwif0->chipset = ide_cmd640;
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
- cmd_hwif0->tuneproc = &cmd640_tune_drive;
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
+ hwif->name, 'a' + cmd640_chip_version - 1, bus_type, cfr);
+
+ hwif->serialized = 1;
+ hwif->chipset = ide_cmd640;
/*
* Ensure compatibility by always using the slowest timings
@@ -789,115 +708,129 @@
/*
* Try to enable the secondary interface, if not already enabled
*/
- if (cmd_hwif1->noprobe) {
- port2 = "not probed";
- } else {
- b = get_cmd640_reg(CNTRL);
- if (secondary_port_responding()) {
- if ((b & CNTRL_ENA_2ND)) {
- second_port_cmd640 = 1;
- port2 = "okay";
- } else if (cmd640_vlb) {
- second_port_cmd640 = 1;
- port2 = "alive";
- } else
- port2 = "not cmd640";
+ if (hwif->channel == 1) //secondary interface
+ {
+ if (hwif->noprobe) {
+ port2 = "not probed";
} else {
- put_cmd640_reg(CNTRL, b ^ CNTRL_ENA_2ND); /* toggle the bit */
+ b = get_cmd640_reg(CNTRL);
if (secondary_port_responding()) {
- second_port_cmd640 = 1;
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
- second_port_toggled = 1;
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
- port2 = "enabled";
+ if ((b & CNTRL_ENA_2ND)) {
+ second_port_cmd640 = 1;
+ port2 = "okay";
+ } else if (cmd640_vlb) {
+ second_port_cmd640 = 1;
+ port2 = "alive";
+ } else
+ port2 = "not cmd640";
} else {
- put_cmd640_reg(CNTRL, b); /* restore original setting */
- port2 = "not responding";
+ put_cmd640_reg(CNTRL, b ^ CNTRL_ENA_2ND); /* toggle the bit */
+ if (secondary_port_responding()) {
+ second_port_cmd640 = 1;
+ second_port_toggled = 1;
+ port2 = "enabled";
+ } else {
+ put_cmd640_reg(CNTRL, b); /* restore original setting */
+ port2 = "not responding";
+ }
}
}
- }
- /*
- * Initialize data for secondary cmd640 port, if enabled
- */
- if (second_port_cmd640) {
- cmd_hwif0->serialized = 1;
- cmd_hwif1->serialized = 1;
- cmd_hwif1->chipset = ide_cmd640;
- cmd_hwif0->mate = cmd_hwif1;
- cmd_hwif1->mate = cmd_hwif0;
- cmd_hwif1->channel = 1;
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
- cmd_hwif1->tuneproc = &cmd640_tune_drive;
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
+ /*
+ * Initialize data for secondary cmd640 port, if enabled
+ */
+ printk(KERN_INFO "%s: %sserialized, secondary interface %s\n",
+ hwif->name, hwif->serialized ? "" : "not ", port2);
}
- printk(KERN_INFO "%s: %sserialized, secondary interface %s\n", cmd_hwif1->name,
- cmd_hwif0->serialized ? "" : "not ", port2);
/*
* Establish initial timings/prefetch for all drives.
* Do not unnecessarily disturb any prior BIOS setup of these.
*/
- for (index = 0; index < (2 + (second_port_cmd640 << 1)); index++) {
- ide_drive_t *drive = cmd_drives[index];
-#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
- if (drive->autotune || ((index > 1) && second_port_toggled)) {
- /*
- * Reset timing to the slowest speed and turn off prefetch.
+ for (i = 0; i < 2; i++) {
+ if (hwif->drives[i].autotune) {
+ /*
+ * Reset timing to the slowest speed and turn off prefetch.
* This way, the drive identify code has a better chance.
*/
- setup_counts [index] = 4; /* max possible */
- active_counts [index] = 16; /* max possible */
- recovery_counts [index] = 16; /* max possible */
- program_drive_counts (index);
- set_prefetch_mode (index, 0);
- printk("cmd640: drive%d timings/prefetch cleared\n", index);
+ setup_counts[2 * hwif->channel + i] = 4; /* max possible */
+ active_counts[2 * hwif->channel + i] = 16; /* max possible */
+ recovery_counts[2 * hwif->channel + i] = 16; /* max possible */
+ program_drive_counts (&(hwif->drives[i]), 4, 16, 16);
+ set_prefetch_mode ((&hwif->drives[i]), 0);
+ printk("cmd640: drive%d timings/prefetch cleared\n", 2 * hwif->channel + i);
} else {
/*
* Record timings/prefetch without changing them.
* This preserves any prior BIOS setup.
*/
- retrieve_drive_counts (index);
- check_prefetch (index);
+ retrieve_drive_counts (&hwif->drives[i]);
+ check_prefetch (&hwif->drives[i]);
printk("cmd640: drive%d timings/prefetch(%s) preserved",
- index, drive->no_io_32bit ? "off" : "on");
- display_clocks(index);
+ 2 * hwif->channel + i,
+ hwif->drives[i].no_io_32bit ? "off" : "on");
+ display_clocks (&hwif->drives[i]);
}
-#else
- /*
- * Set the drive unmask flags to match the prefetch setting
- */
- check_prefetch (index);
- printk("cmd640: drive%d timings/prefetch(%s) preserved\n",
- index, drive->no_io_32bit ? "off" : "on");
-#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
}
#ifdef CMD640_DUMP_REGS
CMD640_DUMP_REGS;
#endif
- return;
-}
-
-static int __init cmd640_init(void)
-{
- ide_register_driver(ide_probe_for_cmd640x);
- return 0;
}
/*
* Called by the IDE core when compiled in and cmd640=vlb is
* selected.
*/
-void init_cmd640_vlb(void)
+void __init init_cmd640_vlb (void)
{
cmd640_vlb = 1;
}
-module_init(cmd640_init);
+extern void ide_setup_pci_device (struct pci_dev *, ide_pci_device_t *);
+
+static int __devinit
+cmd640_init_one (struct pci_dev *dev, const struct pci_device_id *id)
+{
+ ide_pci_device_t *d = &cmd640_chipsets[id->driver_data];
+ if (dev->device != d->device)
+ BUG ();
+ ide_setup_pci_device (dev, d);
+ MOD_INC_USE_COUNT;
+ return 0;
+}
+
+static struct pci_device_id cmd640_pci_tbl[] __devinitdata = {
+ {PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_640, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ 0},
+ {0,},
+};
+
+static struct pci_driver driver = {
+ .name = "CMD640 IDE",
+ .id_table = cmd640_pci_tbl,
+ .probe = cmd640_init_one,
+};
-MODULE_AUTHOR("See Source");
+static int __init
+cmd640_ide_init (void)
+{
+ return ide_pci_register_driver (&driver);
+}
+
+static void __exit
+cmd640_ide_exit (void)
+{
+ ide_pci_unregister_driver (&driver);
+}
+
+module_init (cmd640_ide_init);
+module_exit (cmd640_ide_exit);
+
+MODULE_AUTHOR("Igor Abramov, Mark Lord, Stefan Talpalaru");
MODULE_DESCRIPTION("IDE support for CMD640 controller");
MODULE_PARM(cmd640_vlb, "i");
MODULE_PARM_DESC(cmd640_vlb, "Set to enable scanning for VLB controllers");
MODULE_LICENSE("GPL");
+
+EXPORT_NO_SYMBOLS;
diff -urN linux-2.4.22/drivers/ide/pci/cmd640.h linux-2.4.22-new/drivers/ide/pci/cmd640.h
--- linux-2.4.22/drivers/ide/pci/cmd640.h 2003-09-10 17:18:22.000000000 +0000
+++ linux-2.4.22-new/drivers/ide/pci/cmd640.h 2003-10-27 23:24:13.000000000 +0000
@@ -5,9 +5,9 @@
#include <linux/pci.h>
#include <linux/ide.h>
-#define IDE_IGNORE ((void *)-1)
+static void init_hwif_cmd640 (ide_hwif_t *);
-static ide_pci_device_t cmd640_chipsets[] __initdata = {
+static ide_pci_device_t cmd640_chipsets[] __devinitdata = {
{
.vendor = PCI_VENDOR_ID_CMD,
.device = PCI_DEVICE_ID_CMD_640,
@@ -15,7 +15,7 @@
.init_setup = NULL,
.init_chipset = NULL,
.init_iops = NULL,
- .init_hwif = IDE_IGNORE,
+ .init_hwif = init_hwif_cmd640,
.init_dma = NULL,
.channels = 2,
.autodma = NODMA,
@@ -25,8 +25,9 @@
},{
.vendor = 0,
.device = 0,
+ .channels = 0,
.bootable = EOL,
}
-}
+};
#endif /* CMD640_H */
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: PATCH: CMD640 IDE chipset
2003-10-29 12:12 ` PATCH: CMD640 IDE chipset Stefan Talpalaru
@ 2003-10-29 12:48 ` Alexander Atanasov
2003-11-10 12:28 ` Stefan Talpalaru
2003-10-29 19:36 ` Bartlomiej Zolnierkiewicz
1 sibling, 1 reply; 10+ messages in thread
From: Alexander Atanasov @ 2003-10-29 12:48 UTC (permalink / raw)
To: Stefan Talpalaru; +Cc: linux-kernel, Bartlomiej Zolnierkiewicz
Hello,
On Wed, 29 Oct 2003 04:12:18 -0800 (PST)
Stefan Talpalaru <stefantalpalaru@yahoo.com> wrote:
> and also some useless code (the wrapers: __put_cmd640_reg() and
> __get_cmd640_reg() - which I removed and placed the locks where
> needed; the pci_conf1() and pci_conf2() functions).
These wrappers were added to correct the locking in
driver. There are places that you must access serveral registers
holding the lock and that's why the wrappers came, so they
are not useless. The locking in your patch is wrong -
the problem is that you call get_cmd640_reg or put_cmd640_reg, which
try to take ide_lock, while already holding it and it's a deadlock
- thats what the wrappers solved. So, please , drop that change.
setup_count |= __get_cmd640_reg(arttim_regs[index]) & 0x3f;
- __put_cmd640_reg(arttim_regs[index], setup_count);
- __put_cmd640_reg(drwtim_regs[index], pack_nibbles(active_count, recovery
_count));
+ setup_count |= get_cmd640_reg(arttim_regs[index]) & 0x3f;
+ put_cmd640_reg(arttim_regs[index], setup_count);
+ put_cmd640_reg(drwtim_regs[index], pack_nibbles(active_count, recovery_c
ount));
spin_unlock_irqrestore(&ide_lock, flags);
}
here
- __put_cmd640_reg(reg, b);
+ put_cmd640_reg(reg, b);
spin_unlock_irqrestore(&ide_lock, flags);
and here for example.
--
have fun,
alex
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: PATCH: CMD640 IDE chipset
2003-10-29 12:12 ` PATCH: CMD640 IDE chipset Stefan Talpalaru
2003-10-29 12:48 ` Alexander Atanasov
@ 2003-10-29 19:36 ` Bartlomiej Zolnierkiewicz
2003-11-10 12:32 ` Stefan Talpalaru
2003-11-10 13:00 ` Stefan Talpalaru
1 sibling, 2 replies; 10+ messages in thread
From: Bartlomiej Zolnierkiewicz @ 2003-10-29 19:36 UTC (permalink / raw)
To: Stefan Talpalaru; +Cc: linux-kernel
On Wednesday 29 of October 2003 13:12, Stefan Talpalaru wrote:
> Hi Bartolomiej!
Hi,
> --- Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> wrote:
> > Hi,
> >
> > Can you please drop all code-style changes (such as foo() -> foo ())
>
> sorry about that, I ran Lindent on it...
Please read Documentation/CodingStyle instead ;-).
> Please excuse me for sending this patch as an attachment,
> but as my mail account is Yahoo! and I'm too lazy to find a better
> sollution, I cannot get the patch through the web interface without
> breaking the lines.
Okay.
> This patch integrates the CMD640 chipset support in the 2.4.22
> kernel. I was using it succesfully in the 2.2.x kernel series, but
> got no result in the 2.4.x kernels. After comparing the 2 versions,
> I noticed errors in the new version (outb_p() instead of outl_p())
> and also some useless code (the wrapers: __put_cmd640_reg() and
> __get_cmd640_reg() - which I removed and placed the locks where needed;
It seems Alexander already covered removal of wrappers...
> the pci_conf1() and pci_conf2() functions).
You can't remove them.
/* Find out what kind of PCI probing is supported otherwise
we break some Adaptec cards... */
> I also removed the CONFIG_BLK_DEV_CMD640_ENHANCED config option, as
> it
> makes little difference for the kernel size.
> The init_hwif_cmd640() function had to be rewritten because it is
> called once for each ide interface found, so the old way of addressing
> all the drives in one run was no longer working. Therefore, to not
> break all the code, came the need for a function that computes the
> index from the ide_drive_t* : calculate_index().
ide_probe_for_cmd640x() should be still be used instead.
By removing setup_device_ptrs() and moving this driver to generic PCI layer,
you broke support for VLB version of CMD640.
Also there is a comment in a cmd640.c:
/*
* The CMD640x chip does not support DWORD config write cycles, but some
* of the BIOSes use them to implement the config services.
*/
which worries me that it might be not safe to move this driver to generic
IDE PCI layer (at least for now).
> The code that handles PIO settings was rearanged in a new function:
> cmd640_tuneproc().
Is this really necessary, it is even harder to read it now...
Stefan, please rework your patch. Thanks.
cheers,
--bartlomiej
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: PATCH: CMD640 IDE chipset
2003-10-29 12:48 ` Alexander Atanasov
@ 2003-11-10 12:28 ` Stefan Talpalaru
0 siblings, 0 replies; 10+ messages in thread
From: Stefan Talpalaru @ 2003-11-10 12:28 UTC (permalink / raw)
To: Alexander Atanasov; +Cc: linux-kernel, Bartlomiej Zolnierkiewicz
Hello Alexander!
> Hello,
> On Wed, 29 Oct 2003 04:12:18 -0800 (PST)
> Stefan Talpalaru <stefantalpalaru@yahoo.com> wrote:
> > and also some useless code (the wrapers: __put_cmd640_reg() and
> > __get_cmd640_reg() - which I removed and placed the locks where
> > needed; the pci_conf1() and pci_conf2() functions).
> These wrappers were added to correct the locking in
> driver. There are places that you must access serveral registers
where?
> holding the lock and that's why the wrappers came, so they
> are not useless. The locking in your patch is wrong -
They are ugly.
> the problem is that you call get_cmd640_reg or put_cmd640_reg, which
> try to take ide_lock, while already holding it and it's a deadlock
I find it hard to believe (I'm running a patched kernel right now!),
but
i'm only a newbie at kernel hacking, so please show me the light (not
joking).
Thanks in advance.
> - thats what the wrappers solved. So, please , drop that change.
> setup_count |= __get_cmd640_reg(arttim_regs[index]) & 0x3f;
> - __put_cmd640_reg(arttim_regs[index], setup_count);
> - __put_cmd640_reg(drwtim_regs[index],
pack_nibbles(active_count, recovery
> _count));
> + setup_count |= get_cmd640_reg(arttim_regs[index]) & 0x3f;
> + put_cmd640_reg(arttim_regs[index], setup_count);
> + put_cmd640_reg(drwtim_regs[index], pack_nibbles(active_count,
recovery_c
> ount));
> spin_unlock_irqrestore(&ide_lock, flags);
> }
> here
> - __put_cmd640_reg(reg, b);
> + put_cmd640_reg(reg, b);
> spin_unlock_irqrestore(&ide_lock, flags);
> and here for example.
> --
> have fun,
> alex
later,
=====
Stefan Talpalaru
__________________________________
Do you Yahoo!?
Protect your identity with Yahoo! Mail AddressGuard
http://antispam.yahoo.com/whatsnewfree
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: PATCH: CMD640 IDE chipset
2003-10-29 19:36 ` Bartlomiej Zolnierkiewicz
@ 2003-11-10 12:32 ` Stefan Talpalaru
2003-11-10 13:00 ` Stefan Talpalaru
1 sibling, 0 replies; 10+ messages in thread
From: Stefan Talpalaru @ 2003-11-10 12:32 UTC (permalink / raw)
To: Bartlomiej Zolnierkiewicz; +Cc: linux-kernel
Hi!
> > Hi Bartolomiej!
> Hi,
> > --- Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
wrote:
> > > Hi,
> > >
> > > Can you please drop all code-style changes (such as foo() -> foo
())
> >
> > sorry about that, I ran Lindent on it...
> Please read Documentation/CodingStyle instead ;-).
I've read it and I got the impression that a code cleanup is in order
but nevermind, I left it as wrongly indented as it was.
> > Please excuse me for sending this patch as an attachment,
> > but as my mail account is Yahoo! and I'm too lazy to find a better
> > sollution, I cannot get the patch through the web interface without
> > breaking the lines.
> Okay.
> > This patch integrates the CMD640 chipset support in the 2.4.22
> > kernel. I was using it succesfully in the 2.2.x kernel series, but
> > got no result in the 2.4.x kernels. After comparing the 2 versions,
> > I noticed errors in the new version (outb_p() instead of outl_p())
> > and also some useless code (the wrapers: __put_cmd640_reg() and
> > __get_cmd640_reg() - which I removed and placed the locks where
needed;
> It seems Alexander already covered removal of wrappers...
> > the pci_conf1() and pci_conf2() functions).
> You can't remove them.
> /* Find out what kind of PCI probing is supported otherwise
> we break some Adaptec cards... */
OK, you are right, i am wrong. This functions are back.
> > I also removed the CONFIG_BLK_DEV_CMD640_ENHANCED config option,
as
> > it
> > makes little difference for the kernel size.
> > The init_hwif_cmd640() function had to be rewritten because it is
> > called once for each ide interface found, so the old way of
addressing
> > all the drives in one run was no longer working. Therefore, to not
> > break all the code, came the need for a function that computes the
> > index from the ide_drive_t* : calculate_index().
> ide_probe_for_cmd640x() should be still be used instead.
I disagree.
> By removing setup_device_ptrs() and moving this driver to generic PCI
layer,
> you broke support for VLB version of CMD640.
I don't have a VLB version to test it on, but by reading the code I
think
that it will work just fine.
Anyway, if I'm wrong I should get a prize for breaking something that
was
allready broken :-)))) .
> Also there is a comment in a cmd640.c:
> /*
> * The CMD640x chip does not support DWORD config write cycles, but
some
> * of the BIOSes use them to implement the config services.
> */
> which worries me that it might be not safe to move this driver to
generic
> IDE PCI layer (at least for now).
Don't worry man, just read the code and you shall find peace of
mind....
> > The code that handles PIO settings was rearanged in a new
function:
> > cmd640_tuneproc().
> Is this really necessary, it is even harder to read it now...
It is necessary, unless the purpose of this piece of code is
readability.
> Stefan, please rework your patch. Thanks.
If you say that the only way I will get this driver fixed is to keep
it
ugly then I will send you a lame patch that does just that.
> cheers,
> --bartlomiej
later,
=====
Stefan Talpalaru
__________________________________
Do you Yahoo!?
Protect your identity with Yahoo! Mail AddressGuard
http://antispam.yahoo.com/whatsnewfree
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: PATCH: CMD640 IDE chipset
2003-10-29 19:36 ` Bartlomiej Zolnierkiewicz
2003-11-10 12:32 ` Stefan Talpalaru
@ 2003-11-10 13:00 ` Stefan Talpalaru
2003-11-11 16:50 ` Bartlomiej Zolnierkiewicz
1 sibling, 1 reply; 10+ messages in thread
From: Stefan Talpalaru @ 2003-11-10 13:00 UTC (permalink / raw)
To: Bartlomiej Zolnierkiewicz; +Cc: linux-kernel
Hi!
> > Hi Bartolomiej!
> Hi,
> > --- Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
wrote:
> > > Hi,
> > >
> > > Can you please drop all code-style changes (such as foo() -> foo
())
> >
> > sorry about that, I ran Lindent on it...
> Please read Documentation/CodingStyle instead ;-).
I've read it and I got the impression that a code cleanup is in order
but nevermind, I left it as wrongly indented as it was.
> > Please excuse me for sending this patch as an attachment,
> > but as my mail account is Yahoo! and I'm too lazy to find a better
> > sollution, I cannot get the patch through the web interface without
> > breaking the lines.
> Okay.
> > This patch integrates the CMD640 chipset support in the 2.4.22
> > kernel. I was using it succesfully in the 2.2.x kernel series, but
> > got no result in the 2.4.x kernels. After comparing the 2 versions,
> > I noticed errors in the new version (outb_p() instead of outl_p())
> > and also some useless code (the wrapers: __put_cmd640_reg() and
> > __get_cmd640_reg() - which I removed and placed the locks where
needed;
> It seems Alexander already covered removal of wrappers...
> > the pci_conf1() and pci_conf2() functions).
> You can't remove them.
> /* Find out what kind of PCI probing is supported otherwise
> we break some Adaptec cards... */
OK, you are right, i am wrong. This functions are back.
> > I also removed the CONFIG_BLK_DEV_CMD640_ENHANCED config option,
as
> > it
> > makes little difference for the kernel size.
> > The init_hwif_cmd640() function had to be rewritten because it is
> > called once for each ide interface found, so the old way of
addressing
> > all the drives in one run was no longer working. Therefore, to not
> > break all the code, came the need for a function that computes the
> > index from the ide_drive_t* : calculate_index().
> ide_probe_for_cmd640x() should be still be used instead.
I disagree.
> By removing setup_device_ptrs() and moving this driver to generic PCI
layer,
> you broke support for VLB version of CMD640.
I don't have a VLB version to test it on, but by reading the code I
think
that it will work just fine.
Anyway, if I'm wrong I should get a prize for breaking something that
was
allready broken :-)))) .
> Also there is a comment in a cmd640.c:
> /*
> * The CMD640x chip does not support DWORD config write cycles, but
some
> * of the BIOSes use them to implement the config services.
> */
> which worries me that it might be not safe to move this driver to
generic
> IDE PCI layer (at least for now).
Don't worry man, just read the code and you shall find peace of
mind....
> > The code that handles PIO settings was rearanged in a new
function:
> > cmd640_tuneproc().
> Is this really necessary, it is even harder to read it now...
It is necessary, unless the purpose of this piece of code is
readability.
> Stefan, please rework your patch. Thanks.
If you say that the only way I will get this driver fixed is to keep
it
ugly then I will send you a lame patch that does just that.
> cheers,
> --bartlomiej
later,
=====
Stefan Talpalaru
__________________________________
Do you Yahoo!?
Protect your identity with Yahoo! Mail AddressGuard
http://antispam.yahoo.com/whatsnewfree
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: PATCH: CMD640 IDE chipset
2003-11-10 13:00 ` Stefan Talpalaru
@ 2003-11-11 16:50 ` Bartlomiej Zolnierkiewicz
2003-11-11 17:26 ` Bartlomiej Zolnierkiewicz
0 siblings, 1 reply; 10+ messages in thread
From: Bartlomiej Zolnierkiewicz @ 2003-11-11 16:50 UTC (permalink / raw)
To: Stefan Talpalaru; +Cc: linux-kernel
On Monday 10 of November 2003 14:00, Stefan Talpalaru wrote:
> > > I also removed the CONFIG_BLK_DEV_CMD640_ENHANCED config option, as it
> > > makes little difference for the kernel size.
> > > The init_hwif_cmd640() function had to be rewritten because it is
> > > called once for each ide interface found, so the old way of addressing
> > > all the drives in one run was no longer working. Therefore, to not
> > > break all the code, came the need for a function that computes the
> > > index from the ide_drive_t* : calculate_index().
> >
> > ide_probe_for_cmd640x() should be still be used instead.
>
> I disagree.
>
> > By removing setup_device_ptrs() and moving this driver to generic PCI
> > layer, you broke support for VLB version of CMD640.
>
> I don't have a VLB version to test it on, but by reading the code I think
> that it will work just fine.
No, it won't be even probed. Note that ide_probe_for_cmd640x() was detecting
both VLB and PCI chipsets. After moving detection to generic IDE PCI layer,
only PCI version of the chipset will be probed (and only after Device/Vendor
ID matching). You are of course free to disagree as much as you want...
> Anyway, if I'm wrong I should get a prize for breaking something that was
> allready broken :-)))) .
>
> > Also there is a comment in a cmd640.c:
> > /*
> > * The CMD640x chip does not support DWORD config write cycles, but some
> > * of the BIOSes use them to implement the config services.
> > */
> > which worries me that it might be not safe to move this driver to generic
> > IDE PCI layer (at least for now).
>
> Don't worry man, just read the code and you shall find peace of mind....
Get serious, piece of mind after reading drivers/ide code? Nah.
> > > The code that handles PIO settings was rearanged in a new function:
> > > cmd640_tuneproc().
> >
> > Is this really necessary, it is even harder to read it now...
>
> It is necessary, unless the purpose of this piece of code is readability.
>
> > Stefan, please rework your patch. Thanks.
>
> If you say that the only way I will get this driver fixed is to keep it
> ugly then I will send you a lame patch that does just that.
Minimize changes, then next time when you need to fix this driver (say in 2.7)
you will spend much less time on tracking changes 2.0.x->2.7.x.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: PATCH: CMD640 IDE chipset
2003-11-11 16:50 ` Bartlomiej Zolnierkiewicz
@ 2003-11-11 17:26 ` Bartlomiej Zolnierkiewicz
0 siblings, 0 replies; 10+ messages in thread
From: Bartlomiej Zolnierkiewicz @ 2003-11-11 17:26 UTC (permalink / raw)
To: Stefan Talpalaru; +Cc: linux-kernel
[ Uhh.. mail was sent too early thanks to KMail's "feature". ]
On Tuesday 11 of November 2003 17:50, Bartlomiej Zolnierkiewicz wrote:
> > > > The code that handles PIO settings was rearanged in a new function:
> > > > cmd640_tuneproc().
> > >
> > > Is this really necessary, it is even harder to read it now...
> >
> > It is necessary, unless the purpose of this piece of code is
> > readability.
No, but I want to know WHY it is necessary.
> > > Stefan, please rework your patch. Thanks.
> >
> > If you say that the only way I will get this driver fixed is to keep it
> > ugly then I will send you a lame patch that does just that.
>
> Minimize changes, then next time when you need to fix this driver (say in
> 2.7) you will spend much less time on tracking changes 2.0.x->2.7.x.
I've get report that fixing outb->outl issue is sufficient to get working driver.
Still dunno about second channel support.
Waiting for a lame patch... :)
--bartlomiej
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2003-11-11 17:26 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2003-10-27 12:26 CMD640 ide driver made to work Stefan Talpalaru
2003-10-27 14:35 ` Bartlomiej Zolnierkiewicz
2003-10-29 12:12 ` PATCH: CMD640 IDE chipset Stefan Talpalaru
2003-10-29 12:48 ` Alexander Atanasov
2003-11-10 12:28 ` Stefan Talpalaru
2003-10-29 19:36 ` Bartlomiej Zolnierkiewicz
2003-11-10 12:32 ` Stefan Talpalaru
2003-11-10 13:00 ` Stefan Talpalaru
2003-11-11 16:50 ` Bartlomiej Zolnierkiewicz
2003-11-11 17:26 ` Bartlomiej Zolnierkiewicz
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).