* Problem with 2.6.14 and up...
@ 2005-11-21 16:24 José Luis Sánchez
2006-01-12 23:21 ` Adrian Bunk
0 siblings, 1 reply; 3+ messages in thread
From: José Luis Sánchez @ 2005-11-21 16:24 UTC (permalink / raw)
To: linux-kernel
Hi,
>From 2.6.14 I have a nasty problem with my SCSI devices. First, see my HW:
----------------------------------
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge
(rev 03)
00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge
(rev 03)
00:04.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
00:04.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
00:04.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
00:04.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
00:0a.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 26)
00:0b.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev
64)
00:0d.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 06)
00:0d.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev
06)
01:00.0 VGA compatible controller: nVidia Corporation NV28 [GeForce4 Ti 4200
AGP 8x] (rev a1)
------------------------
I'm using the ncr53c8xx SCSI driver. When I run K3b, the program stalls a few
minutes and this appears in the messages file:
sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:1:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
sr 0:0:2:0: Attached scsi CD-ROM sr1
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 0:0:1:0: Attached scsi generic sg1 type 5
sr 0:0:2:0: Attached scsi generic sg2 type 5
0:0:5:0: Attached scsi generic sg3 type 1
sr 0:0:2:0: phase change 2-1 12@01bbcf60 resid=6.
sr 0:0:2:0: ABORT operation started.
sr 0:0:2:0: ABORT operation timed-out.
sr 0:0:2:0: DEVICE RESET operation started.
sr 0:0:2:0: DEVICE RESET operation timed-out.
sr 0:0:2:0: BUS RESET operation started.
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
sr 0:0:2:0: BUS RESET operation complete.
sr 0:0:2:0: phase change 2-1 12@01bbcf60 resid=6.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
sr 0:0:2:0: phase change 2-1 12@01bbcf60 resid=6.
sr 0:0:2:0: phase change 2-3 12@01bbcf60 resid=2.
sr 0:0:2:0: phase change 2-3 12@01bbcf60 resid=2.
sr 0:0:2:0: phase change 2-3 12@01bbcf60 resid=2.
....
I'm very sure what the SCSI card, the cabling and the devices are OK, why
don't have any problem with 2.4.32 kernel.
Ideas?
José Luis
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: Problem with 2.6.14 and up...
2005-11-21 16:24 Problem with 2.6.14 and up José Luis Sánchez
@ 2006-01-12 23:21 ` Adrian Bunk
2006-01-13 9:44 ` José Luis
0 siblings, 1 reply; 3+ messages in thread
From: Adrian Bunk @ 2006-01-12 23:21 UTC (permalink / raw)
To: José Luis Sánchez; +Cc: linux-kernel, axboe, linux-scsi, matthew
On Mon, Nov 21, 2005 at 05:24:47PM +0100, José Luis Sánchez wrote:
> Hi,
Hi José,
> >From 2.6.14 I have a nasty problem with my SCSI devices. First, see my HW:
>
> ----------------------------------
> 00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge
> (rev 03)
> 00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge
> (rev 03)
> 00:04.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
> 00:04.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
> 00:04.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
> 00:04.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
> 00:0a.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 26)
> 00:0b.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev
> 64)
> 00:0d.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 06)
> 00:0d.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev
> 06)
> 01:00.0 VGA compatible controller: nVidia Corporation NV28 [GeForce4 Ti 4200
> AGP 8x] (rev a1)
> ------------------------
>
> I'm using the ncr53c8xx SCSI driver. When I run K3b, the program stalls a few
> minutes and this appears in the messages file:
>
> sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.20
> sr 0:0:1:0: Attached scsi CD-ROM sr0
> sr1: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
> sr 0:0:2:0: Attached scsi CD-ROM sr1
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> sr 0:0:1:0: Attached scsi generic sg1 type 5
> sr 0:0:2:0: Attached scsi generic sg2 type 5
> 0:0:5:0: Attached scsi generic sg3 type 1
> sr 0:0:2:0: phase change 2-1 12@01bbcf60 resid=6.
> sr 0:0:2:0: ABORT operation started.
> sr 0:0:2:0: ABORT operation timed-out.
> sr 0:0:2:0: DEVICE RESET operation started.
> sr 0:0:2:0: DEVICE RESET operation timed-out.
> sr 0:0:2:0: BUS RESET operation started.
> sym0: SCSI BUS reset detected.
> sym0: SCSI BUS has been reset.
> sr 0:0:2:0: BUS RESET operation complete.
> sr 0:0:2:0: phase change 2-1 12@01bbcf60 resid=6.
> Device not ready. Make sure there is a disc in the drive.
> Device not ready. Make sure there is a disc in the drive.
> sr 0:0:2:0: phase change 2-1 12@01bbcf60 resid=6.
> sr 0:0:2:0: phase change 2-3 12@01bbcf60 resid=2.
> sr 0:0:2:0: phase change 2-3 12@01bbcf60 resid=2.
> sr 0:0:2:0: phase change 2-3 12@01bbcf60 resid=2.
> ....
>
> I'm very sure what the SCSI card, the cabling and the devices are OK, why
> don't have any problem with 2.4.32 kernel.
>
> Ideas?
is this problem still present in kernel 2.6.15?
> José Luis
cu
Adrian
--
"Is there not promise of rain?" Ling Tan asked suddenly out
of the darkness. There had been need of rain for many days.
"Only a promise," Lao Er said.
Pearl S. Buck - Dragon Seed
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: Problem with 2.6.14 and up...
2006-01-12 23:21 ` Adrian Bunk
@ 2006-01-13 9:44 ` José Luis
0 siblings, 0 replies; 3+ messages in thread
From: José Luis @ 2006-01-13 9:44 UTC (permalink / raw)
To: Adrian Bunk; +Cc: linux-kernel, axboe, linux-scsi, matthew
Hi Adrian,
Adrian Bunk wrote:
>On Mon, Nov 21, 2005 at 05:24:47PM +0100, José Luis Sánchez wrote:
>
>
>
>>Hi,
>>
>>
>
>Hi José,
>
>
>
>>>From 2.6.14 I have a nasty problem with my SCSI devices. First, see my HW:
>>
>>----------------------------------
>>00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge
>>(rev 03)
>>00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge
>>(rev 03)
>>00:04.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
>>00:04.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
>>00:04.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
>>00:04.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
>>00:0a.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 26)
>>00:0b.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev
>>64)
>>00:0d.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 06)
>>00:0d.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev
>>06)
>>01:00.0 VGA compatible controller: nVidia Corporation NV28 [GeForce4 Ti 4200
>>AGP 8x] (rev a1)
>>------------------------
>>
>>I'm using the ncr53c8xx SCSI driver. When I run K3b, the program stalls a few
>>minutes and this appears in the messages file:
>>
>>sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray
>>Uniform CD-ROM driver Revision: 3.20
>>sr 0:0:1:0: Attached scsi CD-ROM sr0
>>sr1: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
>>sr 0:0:2:0: Attached scsi CD-ROM sr1
>>sd 0:0:0:0: Attached scsi generic sg0 type 0
>>sr 0:0:1:0: Attached scsi generic sg1 type 5
>>sr 0:0:2:0: Attached scsi generic sg2 type 5
>> 0:0:5:0: Attached scsi generic sg3 type 1
>>sr 0:0:2:0: phase change 2-1 12@01bbcf60 resid=6.
>>sr 0:0:2:0: ABORT operation started.
>>sr 0:0:2:0: ABORT operation timed-out.
>>sr 0:0:2:0: DEVICE RESET operation started.
>>sr 0:0:2:0: DEVICE RESET operation timed-out.
>>sr 0:0:2:0: BUS RESET operation started.
>>sym0: SCSI BUS reset detected.
>>sym0: SCSI BUS has been reset.
>>sr 0:0:2:0: BUS RESET operation complete.
>>sr 0:0:2:0: phase change 2-1 12@01bbcf60 resid=6.
>>Device not ready. Make sure there is a disc in the drive.
>>Device not ready. Make sure there is a disc in the drive.
>>sr 0:0:2:0: phase change 2-1 12@01bbcf60 resid=6.
>>sr 0:0:2:0: phase change 2-3 12@01bbcf60 resid=2.
>>sr 0:0:2:0: phase change 2-3 12@01bbcf60 resid=2.
>>sr 0:0:2:0: phase change 2-3 12@01bbcf60 resid=2.
>>....
>>
>>I'm very sure what the SCSI card, the cabling and the devices are OK, why
>>don't have any problem with 2.4.32 kernel.
>>
>>Ideas?
>>
>>
>
>
>is this problem still present in kernel 2.6.15?
>
>
Sadly, yes, exactly the same problem. I've changed the Tekram SCSI card
by an Adaptec AHA-2940UW and the problem continues. The error messages
are different, but the problem is the same.
Finally, I've changed the SCSI CD-ROMs by a IDE DVD-ROM.... :(
José Luis
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2006-01-13 9:44 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2005-11-21 16:24 Problem with 2.6.14 and up José Luis Sánchez
2006-01-12 23:21 ` Adrian Bunk
2006-01-13 9:44 ` José Luis
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).