* [git patches] libata updates
@ 2006-02-01 4:14 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2006-02-01 4:14 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, linux-kernel
Please pull from 'upstream-fixes' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git
to receive the following updates:
drivers/scsi/ahci.c | 19 +++++++++++++++----
1 files changed, 15 insertions(+), 4 deletions(-)
Jeff Garzik:
[libata ahci] Isolate Intel-ism, add JMicron JMB360 support
[libata ahci] add another JMicron pci id
diff --git a/drivers/scsi/ahci.c b/drivers/scsi/ahci.c
index 19bd346..a800fb5 100644
--- a/drivers/scsi/ahci.c
+++ b/drivers/scsi/ahci.c
@@ -286,6 +286,10 @@ static const struct pci_device_id ahci_p
board_ahci }, /* ICH8M */
{ PCI_VENDOR_ID_INTEL, 0x282a, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ICH8M */
+ { 0x197b, 0x2360, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* JMicron JMB360 */
+ { 0x197b, 0x2363, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* JMicron JMB363 */
{ } /* terminate list */
};
@@ -802,7 +806,6 @@ static int ahci_host_init(struct ata_pro
struct pci_dev *pdev = to_pci_dev(probe_ent->dev);
void __iomem *mmio = probe_ent->mmio_base;
u32 tmp, cap_save;
- u16 tmp16;
unsigned int i, j, using_dac;
int rc;
void __iomem *port_mmio;
@@ -836,9 +839,13 @@ static int ahci_host_init(struct ata_pro
writel(0xf, mmio + HOST_PORTS_IMPL);
(void) readl(mmio + HOST_PORTS_IMPL); /* flush */
- pci_read_config_word(pdev, 0x92, &tmp16);
- tmp16 |= 0xf;
- pci_write_config_word(pdev, 0x92, tmp16);
+ if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
+ u16 tmp16;
+
+ pci_read_config_word(pdev, 0x92, &tmp16);
+ tmp16 |= 0xf;
+ pci_write_config_word(pdev, 0x92, tmp16);
+ }
hpriv->cap = readl(mmio + HOST_CAP);
hpriv->port_map = readl(mmio + HOST_PORTS_IMPL);
@@ -1082,6 +1089,10 @@ static int ahci_init_one (struct pci_dev
if (have_msi)
hpriv->flags |= AHCI_FLAG_MSI;
+ /* JMicron-specific fixup: make sure we're in AHCI mode */
+ if (pdev->vendor == 0x197b)
+ pci_write_config_byte(pdev, 0x41, 0xa1);
+
/* initialize adapter */
rc = ahci_host_init(probe_ent);
if (rc)
^ permalink raw reply related [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2013-04-30 22:26 Jeff Garzik
@ 2013-04-30 23:18 ` Linus Torvalds
0 siblings, 0 replies; 95+ messages in thread
From: Linus Torvalds @ 2013-04-30 23:18 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Andrew Morton, IDE-ML, LKML
On Tue, Apr 30, 2013 at 3:26 PM, Jeff Garzik <jeff@garzik.org> wrote:
>
> Summary:
return -EMISSINGDIFFSTAT;
I've pulled, but *please* make sure to fix your broken script. I
really do want to see the diffstat, partly because I want to know what
to expect even before pulling, partly just to verify that what I
pulled actually matches what you expected me to pull (iow, hopefully
you actually read your own diffstat and anything surprising would have
jumped out at you).
Linus
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2013-04-30 22:26 Jeff Garzik
2013-04-30 23:18 ` Linus Torvalds
0 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2013-04-30 22:26 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Summary:
1) More ACPI fixes, cleanups
2) Minor cleanups for sata_highbank, pata_at32, pata_octeon_cf,
sata_rcar
3) pata_legacy: small bug found in opti chipset code (untested fix,
due to ancient h/w)
4) sata_fsl: RX water mark config knob, some h/w needs it
5) pata_imx: cleanups, DeviceTree support
6) SCSI<->ATA translator: properly export translator version,
not device firmware version
Please pull 2cc1144a31f76d4a9fb48bec5d6ba1359f980813 from
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev.git tags/upstream-linus
to receive the following updates:
Aaron Lu (2):
libata-acpi: remove redundent code for power resource handling
[libata] acpi: make ata_ap_acpi_handle not block
Alexandru Gheorghiu (1):
pata_octeon_cf: Use resource_size function
Baruch Even (1):
[libata] SCSI: really use SATL version in VPD
Dan Carpenter (1):
pata_legacy: bogus clock in opti82c46x_set_piomode()
Jingoo Han (2):
pata_at32: use module_platform_driver_probe()
sata_highbank: make ahci_highbank_pm_ops static
Lv Zheng (1):
ACPI/libata: Restore libata.noacpi support
Qiang Liu (1):
fsl/sata: create a sysfs entry for rx water mark
Robert Richter (1):
sata_highbank: Rename proc_name to the module name
Sachin Kamat (1):
sata_rcar: Convert to devm_ioremap_resource()
Sascha Hauer (4):
pata_imx: Use devm_clk_get
pata_imx: cleanup error path
pata_imx: use void __iomem * for regs
pata_imx: add devicetree support
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-26 2:10 ` Jeff Garzik
@ 2012-07-26 17:14 ` Linus Torvalds
0 siblings, 0 replies; 95+ messages in thread
From: Linus Torvalds @ 2012-07-26 17:14 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Andrew Morton, linux-ide, linux-scsi, LKML
On Wed, Jul 25, 2012 at 7:10 PM, Jeff Garzik <jgarzik@pobox.com> wrote:
>
> Thanks, so noted. I guess if the merge gets more complex than something
> easily described in an email, that implies that maintainers should do more
> cross-coordination and maybe a merge tree.
It's fairly rare. It happens mostly with the arch trees for some
reason - the ARM tree used to be an unholy mess.
And then we have the small "oops, we didn't even notice" things when
some driver (or FS) interface changes, and we have a new driver/fs or
just extended an old one, and there's a subtle conflict. And people
miss those, and quite frankly, it's not a huge deal. We can fix it up
later. It's the "oh, I knew about this" cases where it's fixed up as a
separate commit I dislike.
And quite frankly, I really do a lot of merges, and over the history
of git we have not had all that many really complicated ones. I
commonly send people email saying "ok, this clashed, you need to
double-check my merge", but it's not common that they are really
problems.
So to a first approximation, I'd actually prefer that submaintainers
not care *at*all* about whether something clashes upstream or not. If
there are consistent and problematic clashes, that implies some deeper
problem, and the solution to that is not "let's pre-merge", but rather
more along the lines of "we're doing something wrong, maybe our
interfaces are crap, or our modularity is wrong, let's think about
it".
And for subsystems where we have had problems, it's actually really
nice if the maintainer sends me the unmerged "this is the work I've
done" tree, and then perhaps has a separate "xyzzy-merged" branch that
has a pre-merged version. For cases like that, I will do the merge
myself, but I'll actually double-check my merge against the maintainer
merge. And it's happened more than once that my merge has differed,
and _my_ merge is the correct one. The maintainer may know his code
better, but I know my merging. I do a ton of them.
For example, this week I've done 66 merges, and 15 of them had
conflicts. Of the 15, only two were interesting iirc, but even those
weren't really "problematic", they were just enough to trigger me to
send out emails to the maintainers about them. And I don't think your
libata merge would really have merited even that, apart from the small
semantic thing (which would also have been trivial with a oneliner
"heads up, check out the semantic change in xyz.c:abcdef()".
> What's the best way for libata to move forward, now that this hideous merge
> has been pushed out to the Well Known libata branches? The
> pre-jgarzik-merge commit you would have pulled is
> dc7f71f486f4f5fa96f6dcf86833da020cde8a11 had my pull request been proper.
I'll take your merge, it's not like it's a huge problem. What I care
most about is the "flow", and I am making a stink just so that this
doesn't become a common issue. We have tons of ugly history, and I'm
not black-and-white - problems happen. Big deal. I just want to make
sure that they don't become systemic.
Linus
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-26 5:17 ` Aaron Lu
@ 2012-07-26 14:58 ` Alan Stern
0 siblings, 0 replies; 95+ messages in thread
From: Alan Stern @ 2012-07-26 14:58 UTC (permalink / raw)
To: Aaron Lu
Cc: James Bottomley, Jeff Garzik, linux-scsi, Lin Ming, linux-ide, LKML
On Thu, 26 Jul 2012, Aaron Lu wrote:
> On 07/26/2012 01:05 PM, James Bottomley wrote:
> > On Thu, 2012-07-26 at 12:47 +0800, Aaron Lu wrote:
> >> On 07/26/2012 05:38 AM, Jeff Garzik wrote:
> >>> On 07/25/2012 04:35 PM, Jeff Garzik wrote:
> >>>> * Updating libata to directly bind with ACPI / runtime power mgmt.
> >>>> This is a pre-req for SATA ZPODD (CD-ROM power management).
> >>>>
> >>>> Touches ACPI (exports++) and SCSI in minor ways. Has been in linux-next
> >>>> for weeks.
> >>>>
> >>>> The rest of [ZPODD] will probably come via SCSI tree, as it involves
> >>>> a lot of updates to the 'sr' driver etc.
> >>>
> >>> BTW Lin and Aaron, note that this did not include these changes:
> >>>
> >>> sr: check support for device busy class events
> >>> sr: support zero power ODD
> >>> sr: make sure ODD is in resumed state in block ioctl
> >>>
> >>> as in the end I wanted to put the brakes on SCSI-touching patches. These
> >>> should be able to go into James' scsi-misc tree with the other SCSI-area
> >>> ZPODD changes.
> >>>
> >>> For those three 'sr' changes listed above, you may add
> >>>
> >>> Acked-by: Jeff Garzik<jgarzik@redhat.com>
> >>>
> >>> when moving them over.
> >>
> >> Thanks Jeff.
> >>
> >> Hi James,
> >> I'll prepare these dropped patches plus some other fixes for ZPODD which
> >> I've sent v2 recently and merge them into v3 for you to review.
> >
> > They weren't exactly dropped ... I've been waiting for you to address
> > Alan Stern's comments, since he's our resident expert on suspend/resume.
>
> Oh, I forgot to mention, that I agree with Alan's comments and have
> addressed them in my v2 patches here:
> http://marc.info/?l=linux-scsi&m=134312317325650&w=2
>
> The 2 patches Alan has comments are:
> http://marc.info/?l=linux-scsi&m=134312311025619&w=2
> http://marc.info/?l=linux-scsi&m=134312308225610&w=2
>
> Hi Alan,
> Are the v2 patches look OK to you?
Yes, they are better now.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-25 23:30 ` Linus Torvalds
2012-07-26 2:10 ` Jeff Garzik
@ 2012-07-26 7:44 ` Ingo Molnar
1 sibling, 0 replies; 95+ messages in thread
From: Ingo Molnar @ 2012-07-26 7:44 UTC (permalink / raw)
To: Linus Torvalds; +Cc: Jeff Garzik, Andrew Morton, linux-ide, linux-scsi, LKML
* Linus Torvalds <torvalds@linux-foundation.org> wrote:
> I couldn't find an example of that in a quick look, it's
> fairly uncommon to have non-conflicting merges that had
> semantic - but not contextual - conflicts. [...]
This:
git log --grep='Semantic merge\|Semantic conflict'
gives over a dozen examples of such semantic merges I've done in
the past 4 years. I fully agree that they are best done in the
merge commit - in hindsight perhaps with a tad more explanation
than I did.
Thanks,
Ingo
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-26 5:05 ` James Bottomley
@ 2012-07-26 5:17 ` Aaron Lu
2012-07-26 14:58 ` Alan Stern
0 siblings, 1 reply; 95+ messages in thread
From: Aaron Lu @ 2012-07-26 5:17 UTC (permalink / raw)
To: James Bottomley, Alan Stern
Cc: Jeff Garzik, linux-scsi, Lin Ming, linux-ide, LKML
On 07/26/2012 01:05 PM, James Bottomley wrote:
> On Thu, 2012-07-26 at 12:47 +0800, Aaron Lu wrote:
>> On 07/26/2012 05:38 AM, Jeff Garzik wrote:
>>> On 07/25/2012 04:35 PM, Jeff Garzik wrote:
>>>> * Updating libata to directly bind with ACPI / runtime power mgmt.
>>>> This is a pre-req for SATA ZPODD (CD-ROM power management).
>>>>
>>>> Touches ACPI (exports++) and SCSI in minor ways. Has been in linux-next
>>>> for weeks.
>>>>
>>>> The rest of [ZPODD] will probably come via SCSI tree, as it involves
>>>> a lot of updates to the 'sr' driver etc.
>>>
>>> BTW Lin and Aaron, note that this did not include these changes:
>>>
>>> sr: check support for device busy class events
>>> sr: support zero power ODD
>>> sr: make sure ODD is in resumed state in block ioctl
>>>
>>> as in the end I wanted to put the brakes on SCSI-touching patches. These
>>> should be able to go into James' scsi-misc tree with the other SCSI-area
>>> ZPODD changes.
>>>
>>> For those three 'sr' changes listed above, you may add
>>>
>>> Acked-by: Jeff Garzik<jgarzik@redhat.com>
>>>
>>> when moving them over.
>>
>> Thanks Jeff.
>>
>> Hi James,
>> I'll prepare these dropped patches plus some other fixes for ZPODD which
>> I've sent v2 recently and merge them into v3 for you to review.
>
> They weren't exactly dropped ... I've been waiting for you to address
> Alan Stern's comments, since he's our resident expert on suspend/resume.
Oh, I forgot to mention, that I agree with Alan's comments and have
addressed them in my v2 patches here:
http://marc.info/?l=linux-scsi&m=134312317325650&w=2
The 2 patches Alan has comments are:
http://marc.info/?l=linux-scsi&m=134312311025619&w=2
http://marc.info/?l=linux-scsi&m=134312308225610&w=2
Hi Alan,
Are the v2 patches look OK to you?
And James,
Do you want me to rebase these patches on top of scsi-misc tree?
Thanks,
Aaron
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-26 4:47 ` Aaron Lu
@ 2012-07-26 5:05 ` James Bottomley
2012-07-26 5:17 ` Aaron Lu
0 siblings, 1 reply; 95+ messages in thread
From: James Bottomley @ 2012-07-26 5:05 UTC (permalink / raw)
To: Aaron Lu; +Cc: Jeff Garzik, linux-scsi, Lin Ming, linux-ide, LKML
On Thu, 2012-07-26 at 12:47 +0800, Aaron Lu wrote:
> On 07/26/2012 05:38 AM, Jeff Garzik wrote:
> > On 07/25/2012 04:35 PM, Jeff Garzik wrote:
> >> * Updating libata to directly bind with ACPI / runtime power mgmt.
> >> This is a pre-req for SATA ZPODD (CD-ROM power management).
> >>
> >> Touches ACPI (exports++) and SCSI in minor ways. Has been in linux-next
> >> for weeks.
> >>
> >> The rest of [ZPODD] will probably come via SCSI tree, as it involves
> >> a lot of updates to the 'sr' driver etc.
> >
> > BTW Lin and Aaron, note that this did not include these changes:
> >
> > sr: check support for device busy class events
> > sr: support zero power ODD
> > sr: make sure ODD is in resumed state in block ioctl
> >
> > as in the end I wanted to put the brakes on SCSI-touching patches. These
> > should be able to go into James' scsi-misc tree with the other SCSI-area
> > ZPODD changes.
> >
> > For those three 'sr' changes listed above, you may add
> >
> > Acked-by: Jeff Garzik <jgarzik@redhat.com>
> >
> > when moving them over.
>
> Thanks Jeff.
>
> Hi James,
> I'll prepare these dropped patches plus some other fixes for ZPODD which
> I've sent v2 recently and merge them into v3 for you to review.
They weren't exactly dropped ... I've been waiting for you to address
Alan Stern's comments, since he's our resident expert on suspend/resume.
James
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-25 21:38 ` Jeff Garzik
@ 2012-07-26 4:47 ` Aaron Lu
2012-07-26 5:05 ` James Bottomley
0 siblings, 1 reply; 95+ messages in thread
From: Aaron Lu @ 2012-07-26 4:47 UTC (permalink / raw)
To: Jeff Garzik, James Bottomley; +Cc: linux-scsi, Lin Ming, linux-ide, LKML
On 07/26/2012 05:38 AM, Jeff Garzik wrote:
> On 07/25/2012 04:35 PM, Jeff Garzik wrote:
>> * Updating libata to directly bind with ACPI / runtime power mgmt.
>> This is a pre-req for SATA ZPODD (CD-ROM power management).
>>
>> Touches ACPI (exports++) and SCSI in minor ways. Has been in linux-next
>> for weeks.
>>
>> The rest of [ZPODD] will probably come via SCSI tree, as it involves
>> a lot of updates to the 'sr' driver etc.
>
> BTW Lin and Aaron, note that this did not include these changes:
>
> sr: check support for device busy class events
> sr: support zero power ODD
> sr: make sure ODD is in resumed state in block ioctl
>
> as in the end I wanted to put the brakes on SCSI-touching patches. These
> should be able to go into James' scsi-misc tree with the other SCSI-area
> ZPODD changes.
>
> For those three 'sr' changes listed above, you may add
>
> Acked-by: Jeff Garzik <jgarzik@redhat.com>
>
> when moving them over.
Thanks Jeff.
Hi James,
I'll prepare these dropped patches plus some other fixes for ZPODD which
I've sent v2 recently and merge them into v3 for you to review.
Thanks,
Aaron
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-25 23:30 ` Linus Torvalds
@ 2012-07-26 2:10 ` Jeff Garzik
2012-07-26 17:14 ` Linus Torvalds
2012-07-26 7:44 ` Ingo Molnar
1 sibling, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2012-07-26 2:10 UTC (permalink / raw)
To: Linus Torvalds; +Cc: Andrew Morton, linux-ide, linux-scsi, LKML
On 07/25/2012 07:30 PM, Linus Torvalds wrote:
> On Wed, Jul 25, 2012 at 3:58 PM, Jeff Garzik <jgarzik@pobox.com> wrote:
>>
>> What is the right course in when a post-merge change is needed?
>
> Just describe the issue and the required change. Than I can just do it
> as part of the merge, and now the whole series is bisectable,
> including the merge itself.
>
> Here's a (fairly bad) example:
>
> http://www.spinics.net/lists/netdev/msg192349.html
>
> and the reason I call that a bad example is not because that's a bad
> pull request, but simply that those are all real data conflicts, not
> the more subtle kind of "it merges fine, but because new code
> introduced uses an interface that changed, you need to do xyz".
Thanks, so noted. I guess if the merge gets more complex than something
easily described in an email, that implies that maintainers should do
more cross-coordination and maybe a merge tree.
What's the best way for libata to move forward, now that this hideous
merge has been pushed out to the Well Known libata branches? The
pre-jgarzik-merge commit you would have pulled is
dc7f71f486f4f5fa96f6dcf86833da020cde8a11 had my pull request been proper.
I can lop off the top 3 commits and force-update the libata-dev.git
branches, then send a new pull request -- but you have grumbled at that
sort of behavior in maintainer trees before too...
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-25 22:58 ` Jeff Garzik
@ 2012-07-25 23:30 ` Linus Torvalds
2012-07-26 2:10 ` Jeff Garzik
2012-07-26 7:44 ` Ingo Molnar
0 siblings, 2 replies; 95+ messages in thread
From: Linus Torvalds @ 2012-07-25 23:30 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Andrew Morton, linux-ide, linux-scsi, LKML
On Wed, Jul 25, 2012 at 3:58 PM, Jeff Garzik <jgarzik@pobox.com> wrote:
>
> What is the right course in when a post-merge change is needed?
Just describe the issue and the required change. Than I can just do it
as part of the merge, and now the whole series is bisectable,
including the merge itself.
Here's a (fairly bad) example:
http://www.spinics.net/lists/netdev/msg192349.html
and the reason I call that a bad example is not because that's a bad
pull request, but simply that those are all real data conflicts, not
the more subtle kind of "it merges fine, but because new code
introduced uses an interface that changed, you need to do xyz".
I couldn't find an example of that in a quick look, it's fairly
uncommon to have non-conflicting merges that had semantic - but not
contextual - conflicts. (Although it does happen, and sometimes it's
actually not the developer, but Stephen Rothwell who notices it in
-next and lets me know before the merge).
Linus
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-25 22:31 ` Linus Torvalds
@ 2012-07-25 22:58 ` Jeff Garzik
2012-07-25 23:30 ` Linus Torvalds
0 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2012-07-25 22:58 UTC (permalink / raw)
To: Linus Torvalds; +Cc: Andrew Morton, linux-ide, linux-scsi, LKML
On 07/25/2012 06:31 PM, Linus Torvalds wrote:
> On Wed, Jul 25, 2012 at 3:26 PM, Jeff Garzik <jgarzik@pobox.com> wrote:
>>
>> Even so, separately, it still needed that post-merge compile fix.
>
> And that's yet another example of how *NOT* to do things.
>
> If the merge has errors like that, then they should be fixed up in the merge.
>
> Please. Don't do this. Let me merge stuff, and you explain in the pull
> request why it gets merge problems. Not this mess.
>
> That merge itself was *trivial*. I do those kinds of fixups in my
> sleep and you don't even need to explain those. The non-trivial part
> you did as a separate commit. But neither of those should have been
> "I'll pre-merge for Linus so that he doesn't see these problems".
What is the right course in when a post-merge change is needed?
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-25 22:26 ` Jeff Garzik
@ 2012-07-25 22:31 ` Linus Torvalds
2012-07-25 22:58 ` Jeff Garzik
0 siblings, 1 reply; 95+ messages in thread
From: Linus Torvalds @ 2012-07-25 22:31 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Andrew Morton, linux-ide, linux-scsi, LKML
On Wed, Jul 25, 2012 at 3:26 PM, Jeff Garzik <jgarzik@pobox.com> wrote:
>
> Even so, separately, it still needed that post-merge compile fix.
And that's yet another example of how *NOT* to do things.
If the merge has errors like that, then they should be fixed up in the merge.
Please. Don't do this. Let me merge stuff, and you explain in the pull
request why it gets merge problems. Not this mess.
That merge itself was *trivial*. I do those kinds of fixups in my
sleep and you don't even need to explain those. The non-trivial part
you did as a separate commit. But neither of those should have been
"I'll pre-merge for Linus so that he doesn't see these problems".
Linus
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-25 22:06 ` Linus Torvalds
@ 2012-07-25 22:26 ` Jeff Garzik
2012-07-25 22:31 ` Linus Torvalds
0 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2012-07-25 22:26 UTC (permalink / raw)
To: Linus Torvalds; +Cc: Andrew Morton, linux-ide, linux-scsi, LKML
On 07/25/2012 06:06 PM, Linus Torvalds wrote:
> On Wed, Jul 25, 2012 at 1:43 PM, Jeff Garzik <jeff@garzik.org> wrote:
>> On Wed, Jul 25, 2012 at 04:35:51PM -0400, Jeff Garzik wrote:
>>> Please pull 641589bff714f39b33ef1d7f02eaa009f2993b64 from
>>> git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev.git tags/upstream
>>>
>>
>> Oh, I forgot to point out the merge commit, making my HEAD more recent
>> than might be expected. There was a merge conflict and an API change
>> that needed to be dealt with, in order for your pull to be correct.
>
> So I'd *much* rather see an explanation of what the conflict is when
> you ask me to pull, and let me handle it, rather than you pre-merging
> things for me. I *want* to see conflicts between subsystems.
> Seriously.
Tried to add some explanation to the merge commit itself, giving plenty
of detail.
Even so, separately, it still needed that post-merge compile fix.
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-25 20:43 ` Jeff Garzik
@ 2012-07-25 22:06 ` Linus Torvalds
2012-07-25 22:26 ` Jeff Garzik
0 siblings, 1 reply; 95+ messages in thread
From: Linus Torvalds @ 2012-07-25 22:06 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Andrew Morton, linux-ide, linux-scsi, LKML
On Wed, Jul 25, 2012 at 1:43 PM, Jeff Garzik <jeff@garzik.org> wrote:
> On Wed, Jul 25, 2012 at 04:35:51PM -0400, Jeff Garzik wrote:
>> Please pull 641589bff714f39b33ef1d7f02eaa009f2993b64 from
>> git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev.git tags/upstream
>>
>
> Oh, I forgot to point out the merge commit, making my HEAD more recent
> than might be expected. There was a merge conflict and an API change
> that needed to be dealt with, in order for your pull to be correct.
So I'd *much* rather see an explanation of what the conflict is when
you ask me to pull, and let me handle it, rather than you pre-merging
things for me. I *want* to see conflicts between subsystems.
Seriously.
Linus
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-25 20:35 Jeff Garzik
2012-07-25 20:43 ` Jeff Garzik
@ 2012-07-25 21:38 ` Jeff Garzik
2012-07-26 4:47 ` Aaron Lu
1 sibling, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2012-07-25 21:38 UTC (permalink / raw)
To: linux-scsi, Lin Ming, Aaron Lu, James Bottomley; +Cc: linux-ide, LKML
On 07/25/2012 04:35 PM, Jeff Garzik wrote:
>
> Please pull 641589bff714f39b33ef1d7f02eaa009f2993b64 from
> git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev.git tags/upstream
>
> (text copied from the upstream-linus tag)
> Notable changes:
>
> * Updating libata to directly bind with ACPI / runtime power mgmt.
> This is a pre-req for SATA ZPODD (CD-ROM power management).
>
> Touches ACPI (exports++) and SCSI in minor ways. Has been in linux-next
> for weeks.
>
> The rest of [ZPODD] will probably come via SCSI tree, as it involves
> a lot of updates to the 'sr' driver etc.
BTW Lin and Aaron, note that this did not include these changes:
sr: check support for device busy class events
sr: support zero power ODD
sr: make sure ODD is in resumed state in block ioctl
as in the end I wanted to put the brakes on SCSI-touching patches.
These should be able to go into James' scsi-misc tree with the other
SCSI-area ZPODD changes.
For those three 'sr' changes listed above, you may add
Acked-by: Jeff Garzik <jgarzik@redhat.com>
when moving them over.
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2012-07-25 20:35 Jeff Garzik
@ 2012-07-25 20:43 ` Jeff Garzik
2012-07-25 22:06 ` Linus Torvalds
2012-07-25 21:38 ` Jeff Garzik
1 sibling, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2012-07-25 20:43 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, linux-scsi, LKML
On Wed, Jul 25, 2012 at 04:35:51PM -0400, Jeff Garzik wrote:
> Please pull 641589bff714f39b33ef1d7f02eaa009f2993b64 from
> git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev.git tags/upstream
>
Oh, I forgot to point out the merge commit, making my HEAD more recent
than might be expected. There was a merge conflict and an API change
that needed to be dealt with, in order for your pull to be correct.
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2012-07-25 20:35 Jeff Garzik
2012-07-25 20:43 ` Jeff Garzik
2012-07-25 21:38 ` Jeff Garzik
0 siblings, 2 replies; 95+ messages in thread
From: Jeff Garzik @ 2012-07-25 20:35 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, linux-scsi, LKML
Please pull 641589bff714f39b33ef1d7f02eaa009f2993b64 from
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev.git tags/upstream
(text copied from the upstream-linus tag)
Notable changes:
* Updating libata to directly bind with ACPI / runtime power mgmt.
This is a pre-req for SATA ZPODD (CD-ROM power management).
Touches ACPI (exports++) and SCSI in minor ways. Has been in linux-next
for weeks.
The rest of [ZPODD] will probably come via SCSI tree, as it involves
a lot of updates to the 'sr' driver etc.
Other, minor changes:
* module_pci_driver() removes a lot of common boilerplate from each
PCI driver
* minor coding style, whitespace cleanups
* pata_pcmcia bug fix, caught by Coccinelle
* pata_imx, sata_dwc_460ex minor vendor updates
* ahci_platform: use simple PM ops, and thereby add hibernation cb's
* Add a few device-specific quirks
to receive the following updates:
drivers/acpi/glue.c | 4 +-
drivers/acpi/power.c | 2 +
drivers/acpi/sleep.c | 2 +
drivers/ata/acard-ahci.c | 13 +--
drivers/ata/ahci.c | 63 +++----
drivers/ata/ahci_platform.c | 10 +-
drivers/ata/ata_generic.c | 15 +--
drivers/ata/libata-acpi.c | 408 ++++++++++++++++++++++++++++-----------
drivers/ata/libata-core.c | 12 +-
drivers/ata/libata-eh.c | 2 +-
drivers/ata/libata-pmp.c | 4 -
drivers/ata/libata-scsi.c | 3 +
drivers/ata/libata-transport.c | 6 +-
drivers/ata/libata.h | 15 +-
drivers/ata/pata_acpi.c | 18 +--
drivers/ata/pata_amd.c | 13 +--
drivers/ata/pata_artop.c | 13 +--
drivers/ata/pata_atiixp.c | 14 +--
drivers/ata/pata_atp867x.c | 13 +--
drivers/ata/pata_cmd640.c | 13 +--
drivers/ata/pata_cmd64x.c | 17 +--
drivers/ata/pata_cs5520.c | 14 +--
drivers/ata/pata_cs5530.c | 13 +--
drivers/ata/pata_cs5535.c | 13 +--
drivers/ata/pata_cs5536.c | 13 +--
drivers/ata/pata_cypress.c | 15 +--
drivers/ata/pata_efar.c | 14 +--
drivers/ata/pata_hpt366.c | 13 +--
drivers/ata/pata_hpt37x.c | 13 +--
drivers/ata/pata_hpt3x2n.c | 13 +--
drivers/ata/pata_hpt3x3.c | 15 +--
drivers/ata/pata_imx.c | 10 +-
drivers/ata/pata_it8213.c | 13 +--
drivers/ata/pata_it821x.c | 14 +--
drivers/ata/pata_jmicron.c | 13 +--
drivers/ata/pata_marvell.c | 14 +--
drivers/ata/pata_mpiix.c | 13 +--
drivers/ata/pata_netcell.c | 14 +--
drivers/ata/pata_ninja32.c | 13 +--
drivers/ata/pata_ns87410.c | 13 +--
drivers/ata/pata_ns87415.c | 13 +--
drivers/ata/pata_oldpiix.c | 14 +--
drivers/ata/pata_opti.c | 14 +--
drivers/ata/pata_optidma.c | 13 +--
drivers/ata/pata_pcmcia.c | 3 +-
drivers/ata/pata_pdc2027x.c | 19 +--
drivers/ata/pata_pdc202xx_old.c | 13 +--
drivers/ata/pata_piccolo.c | 16 +--
drivers/ata/pata_radisys.c | 14 +--
drivers/ata/pata_rdc.c | 13 +--
drivers/ata/pata_rz1000.c | 14 +--
drivers/ata/pata_sc1200.c | 13 +--
drivers/ata/pata_scc.c | 21 +--
drivers/ata/pata_sch.c | 13 +--
drivers/ata/pata_serverworks.c | 13 +--
drivers/ata/pata_sil680.c | 13 +--
drivers/ata/pata_sis.c | 14 +--
drivers/ata/pata_sl82c105.c | 13 +--
drivers/ata/pata_triflex.c | 13 +--
drivers/ata/pata_via.c | 13 +--
drivers/ata/pdc_adma.c | 13 +--
drivers/ata/sata_dwc_460ex.c | 72 +++++--
drivers/ata/sata_inic162x.c | 13 +--
drivers/ata/sata_nv.c | 13 +--
drivers/ata/sata_promise.c | 13 +--
drivers/ata/sata_qstor.c | 13 +--
drivers/ata/sata_sil.c | 14 +--
drivers/ata/sata_sil24.c | 13 +--
drivers/ata/sata_sis.c | 13 +--
drivers/ata/sata_svw.c | 13 +--
drivers/ata/sata_sx4.c | 16 +--
drivers/ata/sata_uli.c | 14 +--
drivers/ata/sata_via.c | 13 +--
drivers/ata/sata_vsc.c | 13 +--
drivers/scsi/scsi_lib.c | 17 ++
include/linux/ata.h | 1 +
include/linux/libata.h | 9 +-
include/scsi/scsi.h | 10 +
include/scsi/scsi_device.h | 1 +
79 files changed, 510 insertions(+), 959 deletions(-)
mode change 100644 => 100755 drivers/ata/sata_dwc_460ex.c
Aaron Lu (1):
libata: tell scsi layer device supports runtime power off
Axel Lin (1):
ata: use module_pci_driver
Daniel J Blueman (1):
[libata] Prevent interface errors with Seagate FreeAgent GoFlex
Fabio Estevam (1):
pata_imx: Convert to clk_prepare_enable/clk_disable_unprepare
H Hartley Sweeten (2):
libata-transport.c: local functions should not be exposed globally
libata-eh.c: local functions should not be exposed globally
Holger Macht (1):
[SCSI] add wrapper to access and set scsi_bus_type in struct acpi_bus_type
Jeff Garzik (2):
drivers/acpi/glue: revert accidental license-related 6b66d95895c bits
[libata] pata_cmd64x: whitespace cleanup
Jeffrin Jose (1):
ahci, trivial: fixed coding style issues related to braces
Julia Lawall (1):
drivers/ata/pata_pcmcia.c: adjust suspicious bit operation
Lin Ming (5):
libata-acpi: set acpi state for SATA port
libata-acpi: add ata port runtime D3Cold support
libata-acpi: register/unregister device to/from power resource
libata: detect Device Attention support
libata-acpi: add missing inlines in libata.h
Mark Nelson (1):
ahci: Enable SB600 64bit DMA on MSI K9AGM2 (MS-7327) v2
Matthew Garrett (2):
libata: bind the Linux device tree to the ACPI device tree
libata: migrate ACPI code over to new bindings
Shiraz Hashim (1):
ahci_platform: add hibernation callbacks
Stephen Rothwell (1):
libata-acpi: fix up for acpi_pm_device_sleep_state API
Thang Q. Nguyen (2):
sata_dwc_460ex: support hardreset
sata_dwc_460ex: device tree may specify dma_channel
diff --git a/drivers/acpi/glue.c b/drivers/acpi/glue.c
index 1564e09..243ee85 100644
--- a/drivers/acpi/glue.c
+++ b/drivers/acpi/glue.c
@@ -39,6 +39,7 @@ int register_acpi_bus_type(struct acpi_bus_type *type)
}
return -ENODEV;
}
+EXPORT_SYMBOL_GPL(register_acpi_bus_type);
int unregister_acpi_bus_type(struct acpi_bus_type *type)
{
@@ -54,6 +55,7 @@ int unregister_acpi_bus_type(struct acpi_bus_type *type)
}
return -ENODEV;
}
+EXPORT_SYMBOL_GPL(unregister_acpi_bus_type);
static struct acpi_bus_type *acpi_get_bus_type(struct bus_type *type)
{
@@ -69,7 +71,6 @@ static struct acpi_bus_type *acpi_get_bus_type(struct bus_type *type)
up_read(&bus_type_sem);
return ret;
}
-EXPORT_SYMBOL_GPL(register_acpi_bus_type);
static int acpi_find_bridge_device(struct device *dev, acpi_handle * handle)
{
@@ -86,7 +87,6 @@ static int acpi_find_bridge_device(struct device *dev, acpi_handle * handle)
up_read(&bus_type_sem);
return ret;
}
-EXPORT_SYMBOL_GPL(unregister_acpi_bus_type);
/* Get device's handler per its address under its parent */
struct acpi_find_child {
diff --git a/drivers/acpi/power.c b/drivers/acpi/power.c
index 894d45c..215ecd0 100644
--- a/drivers/acpi/power.c
+++ b/drivers/acpi/power.c
@@ -392,6 +392,7 @@ void acpi_power_resource_unregister_device(struct device *dev, acpi_handle handl
__acpi_power_resource_unregister_device(dev,
list->handles[i]);
}
+EXPORT_SYMBOL_GPL(acpi_power_resource_unregister_device);
static int __acpi_power_resource_register_device(
struct acpi_power_managed_device *powered_device, acpi_handle handle)
@@ -462,6 +463,7 @@ no_power_resource:
printk(KERN_WARNING PREFIX "Invalid Power Resource to register!");
return -ENODEV;
}
+EXPORT_SYMBOL_GPL(acpi_power_resource_register_device);
/**
* acpi_device_sleep_wake - execute _DSW (Device Sleep Wake) or (deprecated in
diff --git a/drivers/acpi/sleep.c b/drivers/acpi/sleep.c
index 1cc02ca..028dd42 100644
--- a/drivers/acpi/sleep.c
+++ b/drivers/acpi/sleep.c
@@ -809,6 +809,7 @@ int acpi_pm_device_sleep_state(struct device *dev, int *d_min_p, int d_max_in)
}
return d_max;
}
+EXPORT_SYMBOL(acpi_pm_device_sleep_state);
#endif /* CONFIG_PM */
#ifdef CONFIG_PM_SLEEP
@@ -845,6 +846,7 @@ int acpi_pm_device_run_wake(struct device *phys_dev, bool enable)
return 0;
}
+EXPORT_SYMBOL(acpi_pm_device_run_wake);
/**
* acpi_pm_device_sleep_wake - enable or disable the system wake-up
diff --git a/drivers/ata/acard-ahci.c b/drivers/ata/acard-ahci.c
index 3bc8c79..4e94ba2 100644
--- a/drivers/ata/acard-ahci.c
+++ b/drivers/ata/acard-ahci.c
@@ -503,21 +503,10 @@ static int acard_ahci_init_one(struct pci_dev *pdev, const struct pci_device_id
&acard_ahci_sht);
}
-static int __init acard_ahci_init(void)
-{
- return pci_register_driver(&acard_ahci_pci_driver);
-}
-
-static void __exit acard_ahci_exit(void)
-{
- pci_unregister_driver(&acard_ahci_pci_driver);
-}
+module_pci_driver(acard_ahci_pci_driver);
MODULE_AUTHOR("Jeff Garzik");
MODULE_DESCRIPTION("ACard AHCI SATA low-level driver");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, acard_ahci_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
-module_init(acard_ahci_init);
-module_exit(acard_ahci_exit);
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index ebaf67e..062e6a1 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -105,31 +105,27 @@ static struct ata_port_operations ahci_p5wdh_ops = {
static const struct ata_port_info ahci_port_info[] = {
/* by features */
- [board_ahci] =
- {
+ [board_ahci] = {
.flags = AHCI_FLAG_COMMON,
.pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
- [board_ahci_ign_iferr] =
- {
+ [board_ahci_ign_iferr] = {
AHCI_HFLAGS (AHCI_HFLAG_IGN_IRQ_IF_ERR),
.flags = AHCI_FLAG_COMMON,
.pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
- [board_ahci_nosntf] =
- {
+ [board_ahci_nosntf] = {
AHCI_HFLAGS (AHCI_HFLAG_NO_SNTF),
.flags = AHCI_FLAG_COMMON,
.pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
- [board_ahci_yes_fbs] =
- {
+ [board_ahci_yes_fbs] = {
AHCI_HFLAGS (AHCI_HFLAG_YES_FBS),
.flags = AHCI_FLAG_COMMON,
.pio_mask = ATA_PIO4,
@@ -137,8 +133,7 @@ static const struct ata_port_info ahci_port_info[] = {
.port_ops = &ahci_ops,
},
/* by chipsets */
- [board_ahci_mcp65] =
- {
+ [board_ahci_mcp65] = {
AHCI_HFLAGS (AHCI_HFLAG_NO_FPDMA_AA | AHCI_HFLAG_NO_PMP |
AHCI_HFLAG_YES_NCQ),
.flags = AHCI_FLAG_COMMON | ATA_FLAG_NO_DIPM,
@@ -146,24 +141,21 @@ static const struct ata_port_info ahci_port_info[] = {
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
- [board_ahci_mcp77] =
- {
+ [board_ahci_mcp77] = {
AHCI_HFLAGS (AHCI_HFLAG_NO_FPDMA_AA | AHCI_HFLAG_NO_PMP),
.flags = AHCI_FLAG_COMMON,
.pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
- [board_ahci_mcp89] =
- {
+ [board_ahci_mcp89] = {
AHCI_HFLAGS (AHCI_HFLAG_NO_FPDMA_AA),
.flags = AHCI_FLAG_COMMON,
.pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
- [board_ahci_mv] =
- {
+ [board_ahci_mv] = {
AHCI_HFLAGS (AHCI_HFLAG_NO_NCQ | AHCI_HFLAG_NO_MSI |
AHCI_HFLAG_MV_PATA | AHCI_HFLAG_NO_PMP),
.flags = ATA_FLAG_SATA | ATA_FLAG_PIO_DMA,
@@ -171,8 +163,7 @@ static const struct ata_port_info ahci_port_info[] = {
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
- [board_ahci_sb600] =
- {
+ [board_ahci_sb600] = {
AHCI_HFLAGS (AHCI_HFLAG_IGN_SERR_INTERNAL |
AHCI_HFLAG_NO_MSI | AHCI_HFLAG_SECT255 |
AHCI_HFLAG_32BIT_ONLY),
@@ -181,16 +172,14 @@ static const struct ata_port_info ahci_port_info[] = {
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_pmp_retry_srst_ops,
},
- [board_ahci_sb700] = /* for SB700 and SB800 */
- {
+ [board_ahci_sb700] = { /* for SB700 and SB800 */
AHCI_HFLAGS (AHCI_HFLAG_IGN_SERR_INTERNAL),
.flags = AHCI_FLAG_COMMON,
.pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_pmp_retry_srst_ops,
},
- [board_ahci_vt8251] =
- {
+ [board_ahci_vt8251] = {
AHCI_HFLAGS (AHCI_HFLAG_NO_NCQ | AHCI_HFLAG_NO_PMP),
.flags = AHCI_FLAG_COMMON,
.pio_mask = ATA_PIO4,
@@ -777,6 +766,22 @@ static bool ahci_sb600_enable_64bit(struct pci_dev *pdev)
},
},
/*
+ * All BIOS versions for the MSI K9AGM2 (MS-7327) support
+ * 64bit DMA.
+ *
+ * This board also had the typo mentioned above in the
+ * Manufacturer DMI field (fixed in BIOS version 1.5), so
+ * match on DMI_BOARD_VENDOR of "MICRO-STAR INTER" again.
+ */
+ {
+ .ident = "MSI K9AGM2",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR,
+ "MICRO-STAR INTER"),
+ DMI_MATCH(DMI_BOARD_NAME, "MS-7327"),
+ },
+ },
+ /*
* All BIOS versions for the Asus M3A support 64bit DMA.
* (all release versions from 0301 to 1206 were tested)
*/
@@ -1233,22 +1238,10 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
&ahci_sht);
}
-static int __init ahci_init(void)
-{
- return pci_register_driver(&ahci_pci_driver);
-}
-
-static void __exit ahci_exit(void)
-{
- pci_unregister_driver(&ahci_pci_driver);
-}
-
+module_pci_driver(ahci_pci_driver);
MODULE_AUTHOR("Jeff Garzik");
MODULE_DESCRIPTION("AHCI SATA low-level driver");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, ahci_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
-module_init(ahci_init);
-module_exit(ahci_exit);
diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c
index 9e419e1..09728e0 100644
--- a/drivers/ata/ahci_platform.c
+++ b/drivers/ata/ahci_platform.c
@@ -15,6 +15,7 @@
#include <linux/kernel.h>
#include <linux/gfp.h>
#include <linux/module.h>
+#include <linux/pm.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/device.h>
@@ -271,13 +272,10 @@ static int ahci_resume(struct device *dev)
return 0;
}
-
-static struct dev_pm_ops ahci_pm_ops = {
- .suspend = &ahci_suspend,
- .resume = &ahci_resume,
-};
#endif
+SIMPLE_DEV_PM_OPS(ahci_pm_ops, ahci_suspend, ahci_resume);
+
static const struct of_device_id ahci_of_match[] = {
{ .compatible = "calxeda,hb-ahci", },
{ .compatible = "snps,spear-ahci", },
@@ -291,9 +289,7 @@ static struct platform_driver ahci_driver = {
.name = "ahci",
.owner = THIS_MODULE,
.of_match_table = ahci_of_match,
-#ifdef CONFIG_PM
.pm = &ahci_pm_ops,
-#endif
},
.id_table = ahci_devtype,
};
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
index aae1156..f8f38a0 100644
--- a/drivers/ata/ata_generic.c
+++ b/drivers/ata/ata_generic.c
@@ -255,17 +255,7 @@ static struct pci_driver ata_generic_pci_driver = {
#endif
};
-static int __init ata_generic_init(void)
-{
- return pci_register_driver(&ata_generic_pci_driver);
-}
-
-
-static void __exit ata_generic_exit(void)
-{
- pci_unregister_driver(&ata_generic_pci_driver);
-}
-
+module_pci_driver(ata_generic_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for generic ATA");
@@ -273,7 +263,4 @@ MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, ata_generic);
MODULE_VERSION(DRV_VERSION);
-module_init(ata_generic_init);
-module_exit(ata_generic_exit);
-
module_param(all_generic_ide, int, 0);
diff --git a/drivers/ata/libata-acpi.c b/drivers/ata/libata-acpi.c
index bb7c5f1..902b5a4 100644
--- a/drivers/ata/libata-acpi.c
+++ b/drivers/ata/libata-acpi.c
@@ -16,6 +16,7 @@
#include <linux/libata.h>
#include <linux/pci.h>
#include <linux/slab.h>
+#include <linux/pm_runtime.h>
#include <scsi/scsi_device.h>
#include "libata.h"
@@ -48,62 +49,53 @@ static void ata_acpi_clear_gtf(struct ata_device *dev)
}
/**
- * ata_acpi_associate_sata_port - associate SATA port with ACPI objects
- * @ap: target SATA port
+ * ata_ap_acpi_handle - provide the acpi_handle for an ata_port
+ * @ap: the acpi_handle returned will correspond to this port
*
- * Look up ACPI objects associated with @ap and initialize acpi_handle
- * fields of @ap, the port and devices accordingly.
- *
- * LOCKING:
- * EH context.
- *
- * RETURNS:
- * 0 on success, -errno on failure.
+ * Returns the acpi_handle for the ACPI namespace object corresponding to
+ * the ata_port passed into the function, or NULL if no such object exists
*/
-void ata_acpi_associate_sata_port(struct ata_port *ap)
+acpi_handle ata_ap_acpi_handle(struct ata_port *ap)
{
- WARN_ON(!(ap->flags & ATA_FLAG_ACPI_SATA));
-
- if (!sata_pmp_attached(ap)) {
- u64 adr = SATA_ADR(ap->port_no, NO_PORT_MULT);
-
- ap->link.device->acpi_handle =
- acpi_get_child(ap->host->acpi_handle, adr);
- } else {
- struct ata_link *link;
-
- ap->link.device->acpi_handle = NULL;
-
- ata_for_each_link(link, ap, EDGE) {
- u64 adr = SATA_ADR(ap->port_no, link->pmp);
+ if (ap->flags & ATA_FLAG_ACPI_SATA)
+ return NULL;
- link->device->acpi_handle =
- acpi_get_child(ap->host->acpi_handle, adr);
- }
- }
+ /*
+ * If acpi bind operation has already happened, we can get the handle
+ * for the port by checking the corresponding scsi_host device's
+ * firmware node, otherwise we will need to find out the handle from
+ * its parent's acpi node.
+ */
+ if (ap->scsi_host)
+ return DEVICE_ACPI_HANDLE(&ap->scsi_host->shost_gendev);
+ else
+ return acpi_get_child(DEVICE_ACPI_HANDLE(ap->host->dev),
+ ap->port_no);
}
+EXPORT_SYMBOL(ata_ap_acpi_handle);
-static void ata_acpi_associate_ide_port(struct ata_port *ap)
+/**
+ * ata_dev_acpi_handle - provide the acpi_handle for an ata_device
+ * @dev: the acpi_device returned will correspond to this port
+ *
+ * Returns the acpi_handle for the ACPI namespace object corresponding to
+ * the ata_device passed into the function, or NULL if no such object exists
+ */
+acpi_handle ata_dev_acpi_handle(struct ata_device *dev)
{
- int max_devices, i;
-
- ap->acpi_handle = acpi_get_child(ap->host->acpi_handle, ap->port_no);
- if (!ap->acpi_handle)
- return;
-
- max_devices = 1;
- if (ap->flags & ATA_FLAG_SLAVE_POSS)
- max_devices++;
-
- for (i = 0; i < max_devices; i++) {
- struct ata_device *dev = &ap->link.device[i];
-
- dev->acpi_handle = acpi_get_child(ap->acpi_handle, i);
- }
+ acpi_integer adr;
+ struct ata_port *ap = dev->link->ap;
- if (ata_acpi_gtm(ap, &ap->__acpi_init_gtm) == 0)
- ap->pflags |= ATA_PFLAG_INIT_GTM_VALID;
+ if (ap->flags & ATA_FLAG_ACPI_SATA) {
+ if (!sata_pmp_attached(ap))
+ adr = SATA_ADR(ap->port_no, NO_PORT_MULT);
+ else
+ adr = SATA_ADR(ap->port_no, dev->link->pmp);
+ return acpi_get_child(DEVICE_ACPI_HANDLE(ap->host->dev), adr);
+ } else
+ return acpi_get_child(ata_ap_acpi_handle(ap), dev->devno);
}
+EXPORT_SYMBOL(ata_dev_acpi_handle);
/* @ap and @dev are the same as ata_acpi_handle_hotplug() */
static void ata_acpi_detach_device(struct ata_port *ap, struct ata_device *dev)
@@ -229,56 +221,6 @@ static const struct acpi_dock_ops ata_acpi_ap_dock_ops = {
};
/**
- * ata_acpi_associate - associate ATA host with ACPI objects
- * @host: target ATA host
- *
- * Look up ACPI objects associated with @host and initialize
- * acpi_handle fields of @host, its ports and devices accordingly.
- *
- * LOCKING:
- * EH context.
- *
- * RETURNS:
- * 0 on success, -errno on failure.
- */
-void ata_acpi_associate(struct ata_host *host)
-{
- int i, j;
-
- if (!is_pci_dev(host->dev) || libata_noacpi)
- return;
-
- host->acpi_handle = DEVICE_ACPI_HANDLE(host->dev);
- if (!host->acpi_handle)
- return;
-
- for (i = 0; i < host->n_ports; i++) {
- struct ata_port *ap = host->ports[i];
-
- if (host->ports[0]->flags & ATA_FLAG_ACPI_SATA)
- ata_acpi_associate_sata_port(ap);
- else
- ata_acpi_associate_ide_port(ap);
-
- if (ap->acpi_handle) {
- /* we might be on a docking station */
- register_hotplug_dock_device(ap->acpi_handle,
- &ata_acpi_ap_dock_ops, ap);
- }
-
- for (j = 0; j < ata_link_max_devices(&ap->link); j++) {
- struct ata_device *dev = &ap->link.device[j];
-
- if (dev->acpi_handle) {
- /* we might be on a docking station */
- register_hotplug_dock_device(dev->acpi_handle,
- &ata_acpi_dev_dock_ops, dev);
- }
- }
- }
-}
-
-/**
* ata_acpi_dissociate - dissociate ATA host from ACPI objects
* @host: target ATA host
*
@@ -299,7 +241,7 @@ void ata_acpi_dissociate(struct ata_host *host)
struct ata_port *ap = host->ports[i];
const struct ata_acpi_gtm *gtm = ata_acpi_init_gtm(ap);
- if (ap->acpi_handle && gtm)
+ if (ata_ap_acpi_handle(ap) && gtm)
ata_acpi_stm(ap, gtm);
}
}
@@ -324,7 +266,8 @@ int ata_acpi_gtm(struct ata_port *ap, struct ata_acpi_gtm *gtm)
acpi_status status;
int rc = 0;
- status = acpi_evaluate_object(ap->acpi_handle, "_GTM", NULL, &output);
+ status = acpi_evaluate_object(ata_ap_acpi_handle(ap), "_GTM", NULL,
+ &output);
rc = -ENOENT;
if (status == AE_NOT_FOUND)
@@ -394,7 +337,8 @@ int ata_acpi_stm(struct ata_port *ap, const struct ata_acpi_gtm *stm)
input.count = 3;
input.pointer = in_params;
- status = acpi_evaluate_object(ap->acpi_handle, "_STM", &input, NULL);
+ status = acpi_evaluate_object(ata_ap_acpi_handle(ap), "_STM", &input,
+ NULL);
if (status == AE_NOT_FOUND)
return -ENOENT;
@@ -451,7 +395,8 @@ static int ata_dev_get_GTF(struct ata_device *dev, struct ata_acpi_gtf **gtf)
__func__, ap->port_no);
/* _GTF has no input parameters */
- status = acpi_evaluate_object(dev->acpi_handle, "_GTF", NULL, &output);
+ status = acpi_evaluate_object(ata_dev_acpi_handle(dev), "_GTF", NULL,
+ &output);
out_obj = dev->gtf_cache = output.pointer;
if (ACPI_FAILURE(status)) {
@@ -817,7 +762,8 @@ static int ata_acpi_push_id(struct ata_device *dev)
/* It's OK for _SDD to be missing too. */
swap_buf_le16(dev->id, ATA_ID_WORDS);
- status = acpi_evaluate_object(dev->acpi_handle, "_SDD", &input, NULL);
+ status = acpi_evaluate_object(ata_dev_acpi_handle(dev), "_SDD", &input,
+ NULL);
swap_buf_le16(dev->id, ATA_ID_WORDS);
if (status == AE_NOT_FOUND)
@@ -867,7 +813,7 @@ void ata_acpi_on_resume(struct ata_port *ap)
const struct ata_acpi_gtm *gtm = ata_acpi_init_gtm(ap);
struct ata_device *dev;
- if (ap->acpi_handle && gtm) {
+ if (ata_ap_acpi_handle(ap) && gtm) {
/* _GTM valid */
/* restore timing parameters */
@@ -907,23 +853,39 @@ void ata_acpi_on_resume(struct ata_port *ap)
void ata_acpi_set_state(struct ata_port *ap, pm_message_t state)
{
struct ata_device *dev;
-
- if (!ap->acpi_handle || (ap->flags & ATA_FLAG_ACPI_SATA))
- return;
+ acpi_handle handle;
+ int acpi_state;
/* channel first and then drives for power on and vica versa
for power off */
- if (state.event == PM_EVENT_ON)
- acpi_bus_set_power(ap->acpi_handle, ACPI_STATE_D0);
+ handle = ata_ap_acpi_handle(ap);
+ if (handle && state.event == PM_EVENT_ON)
+ acpi_bus_set_power(handle, ACPI_STATE_D0);
ata_for_each_dev(dev, &ap->link, ENABLED) {
- if (dev->acpi_handle)
- acpi_bus_set_power(dev->acpi_handle,
- state.event == PM_EVENT_ON ?
- ACPI_STATE_D0 : ACPI_STATE_D3);
+ handle = ata_dev_acpi_handle(dev);
+ if (!handle)
+ continue;
+
+ if (state.event != PM_EVENT_ON) {
+ acpi_state = acpi_pm_device_sleep_state(
+ &dev->sdev->sdev_gendev, NULL, ACPI_STATE_D3);
+ if (acpi_state > 0)
+ acpi_bus_set_power(handle, acpi_state);
+ /* TBD: need to check if it's runtime pm request */
+ acpi_pm_device_run_wake(
+ &dev->sdev->sdev_gendev, true);
+ } else {
+ /* Ditto */
+ acpi_pm_device_run_wake(
+ &dev->sdev->sdev_gendev, false);
+ acpi_bus_set_power(handle, ACPI_STATE_D0);
+ }
}
- if (state.event != PM_EVENT_ON)
- acpi_bus_set_power(ap->acpi_handle, ACPI_STATE_D3);
+
+ handle = ata_ap_acpi_handle(ap);
+ if (handle && state.event != PM_EVENT_ON)
+ acpi_bus_set_power(handle, ACPI_STATE_D3);
}
/**
@@ -948,7 +910,7 @@ int ata_acpi_on_devcfg(struct ata_device *dev)
int nr_executed = 0;
int rc;
- if (!dev->acpi_handle)
+ if (!ata_dev_acpi_handle(dev))
return 0;
/* do we need to do _GTF? */
@@ -994,7 +956,6 @@ int ata_acpi_on_devcfg(struct ata_device *dev)
}
ata_dev_warn(dev, "ACPI: failed the second time, disabled\n");
- dev->acpi_handle = NULL;
/* We can safely continue if no _GTF command has been executed
* and port is not frozen.
@@ -1018,3 +979,218 @@ void ata_acpi_on_disable(struct ata_device *dev)
{
ata_acpi_clear_gtf(dev);
}
+
+static void ata_acpi_wake_dev(acpi_handle handle, u32 event, void *context)
+{
+ struct ata_device *ata_dev = context;
+
+ if (event == ACPI_NOTIFY_DEVICE_WAKE && ata_dev &&
+ pm_runtime_suspended(&ata_dev->sdev->sdev_gendev))
+ scsi_autopm_get_device(ata_dev->sdev);
+}
+
+static void ata_acpi_add_pm_notifier(struct ata_device *dev)
+{
+ struct acpi_device *acpi_dev;
+ acpi_handle handle;
+ acpi_status status;
+
+ handle = ata_dev_acpi_handle(dev);
+ if (!handle)
+ return;
+
+ status = acpi_bus_get_device(handle, &acpi_dev);
+ if (ACPI_FAILURE(status))
+ return;
+
+ if (dev->sdev->can_power_off) {
+ acpi_install_notify_handler(handle, ACPI_SYSTEM_NOTIFY,
+ ata_acpi_wake_dev, dev);
+ device_set_run_wake(&dev->sdev->sdev_gendev, true);
+ }
+}
+
+static void ata_acpi_remove_pm_notifier(struct ata_device *dev)
+{
+ struct acpi_device *acpi_dev;
+ acpi_handle handle;
+ acpi_status status;
+
+ handle = ata_dev_acpi_handle(dev);
+ if (!handle)
+ return;
+
+ status = acpi_bus_get_device(handle, &acpi_dev);
+ if (ACPI_FAILURE(status))
+ return;
+
+ if (dev->sdev->can_power_off) {
+ device_set_run_wake(&dev->sdev->sdev_gendev, false);
+ acpi_remove_notify_handler(handle, ACPI_SYSTEM_NOTIFY,
+ ata_acpi_wake_dev);
+ }
+}
+
+static void ata_acpi_register_power_resource(struct ata_device *dev)
+{
+ struct scsi_device *sdev = dev->sdev;
+ acpi_handle handle;
+ struct device *device;
+
+ handle = ata_dev_acpi_handle(dev);
+ if (!handle)
+ return;
+
+ device = &sdev->sdev_gendev;
+
+ acpi_power_resource_register_device(device, handle);
+}
+
+static void ata_acpi_unregister_power_resource(struct ata_device *dev)
+{
+ struct scsi_device *sdev = dev->sdev;
+ acpi_handle handle;
+ struct device *device;
+
+ handle = ata_dev_acpi_handle(dev);
+ if (!handle)
+ return;
+
+ device = &sdev->sdev_gendev;
+
+ acpi_power_resource_unregister_device(device, handle);
+}
+
+void ata_acpi_bind(struct ata_device *dev)
+{
+ ata_acpi_add_pm_notifier(dev);
+ ata_acpi_register_power_resource(dev);
+}
+
+void ata_acpi_unbind(struct ata_device *dev)
+{
+ ata_acpi_remove_pm_notifier(dev);
+ ata_acpi_unregister_power_resource(dev);
+}
+
+static int compat_pci_ata(struct ata_port *ap)
+{
+ struct device *dev = ap->tdev.parent;
+ struct pci_dev *pdev;
+
+ if (!is_pci_dev(dev))
+ return 0;
+
+ pdev = to_pci_dev(dev);
+
+ if ((pdev->class >> 8) != PCI_CLASS_STORAGE_SATA &&
+ (pdev->class >> 8) != PCI_CLASS_STORAGE_IDE)
+ return 0;
+
+ return 1;
+}
+
+static int ata_acpi_bind_host(struct ata_port *ap, acpi_handle *handle)
+{
+ if (ap->flags & ATA_FLAG_ACPI_SATA)
+ return -ENODEV;
+
+ *handle = acpi_get_child(DEVICE_ACPI_HANDLE(ap->tdev.parent),
+ ap->port_no);
+
+ if (!*handle)
+ return -ENODEV;
+
+ return 0;
+}
+
+static int ata_acpi_bind_device(struct ata_port *ap, struct scsi_device *sdev,
+ acpi_handle *handle)
+{
+ struct ata_device *ata_dev;
+ acpi_status status;
+ struct acpi_device *acpi_dev;
+ struct acpi_device_power_state *states;
+
+ if (ap->flags & ATA_FLAG_ACPI_SATA)
+ ata_dev = &ap->link.device[sdev->channel];
+ else
+ ata_dev = &ap->link.device[sdev->id];
+
+ *handle = ata_dev_acpi_handle(ata_dev);
+
+ if (!*handle)
+ return -ENODEV;
+
+ status = acpi_bus_get_device(*handle, &acpi_dev);
+ if (ACPI_FAILURE(status))
+ return 0;
+
+ /*
+ * If firmware has _PS3 or _PR3 for this device,
+ * and this ata ODD device support device attention,
+ * it means this device can be powered off
+ */
+ states = acpi_dev->power.states;
+ if ((states[ACPI_STATE_D3_HOT].flags.valid ||
+ states[ACPI_STATE_D3_COLD].flags.explicit_set) &&
+ ata_dev->flags & ATA_DFLAG_DA)
+ sdev->can_power_off = 1;
+
+ return 0;
+}
+
+static int is_ata_port(const struct device *dev)
+{
+ return dev->type == &ata_port_type;
+}
+
+static struct ata_port *dev_to_ata_port(struct device *dev)
+{
+ while (!is_ata_port(dev)) {
+ if (!dev->parent)
+ return NULL;
+ dev = dev->parent;
+ }
+ return to_ata_port(dev);
+}
+
+static int ata_acpi_find_device(struct device *dev, acpi_handle *handle)
+{
+ struct ata_port *ap = dev_to_ata_port(dev);
+
+ if (!ap)
+ return -ENODEV;
+
+ if (!compat_pci_ata(ap))
+ return -ENODEV;
+
+ if (scsi_is_host_device(dev))
+ return ata_acpi_bind_host(ap, handle);
+ else if (scsi_is_sdev_device(dev)) {
+ struct scsi_device *sdev = to_scsi_device(dev);
+
+ return ata_acpi_bind_device(ap, sdev, handle);
+ } else
+ return -ENODEV;
+}
+
+static int ata_acpi_find_dummy(struct device *dev, acpi_handle *handle)
+{
+ return -ENODEV;
+}
+
+static struct acpi_bus_type ata_acpi_bus = {
+ .find_bridge = ata_acpi_find_dummy,
+ .find_device = ata_acpi_find_device,
+};
+
+int ata_acpi_register(void)
+{
+ return scsi_register_acpi_bus_type(&ata_acpi_bus);
+}
+
+void ata_acpi_unregister(void)
+{
+ scsi_unregister_acpi_bus_type(&ata_acpi_bus);
+}
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 3fe1202..fadd586 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -2376,6 +2376,9 @@ int ata_dev_configure(struct ata_device *dev)
dma_dir_string = ", DMADIR";
}
+ if (ata_id_has_da(dev->id))
+ dev->flags |= ATA_DFLAG_DA;
+
/* print device info to dmesg */
if (ata_msg_drv(ap) && print_info)
ata_dev_info(dev,
@@ -4128,6 +4131,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
/* Devices which aren't very happy with higher link speeds */
{ "WD My Book", NULL, ATA_HORKAGE_1_5_GBPS, },
+ { "Seagate FreeAgent GoFlex", NULL, ATA_HORKAGE_1_5_GBPS, },
/*
* Devices which choke on SETXFER. Applies only if both the
@@ -5290,8 +5294,6 @@ static int ata_port_request_pm(struct ata_port *ap, pm_message_t mesg,
return rc;
}
-#define to_ata_port(d) container_of(d, struct ata_port, tdev)
-
static int ata_port_suspend_common(struct device *dev, pm_message_t mesg)
{
struct ata_port *ap = to_ata_port(dev);
@@ -6053,9 +6055,6 @@ int ata_host_register(struct ata_host *host, struct scsi_host_template *sht)
if (rc)
goto err_tadd;
- /* associate with ACPI nodes */
- ata_acpi_associate(host);
-
/* set cable, sata_spd_limit and report */
for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap = host->ports[i];
@@ -6515,6 +6514,8 @@ static int __init ata_init(void)
ata_parse_force_param();
+ ata_acpi_register();
+
rc = ata_sff_init();
if (rc) {
kfree(ata_force_tbl);
@@ -6541,6 +6542,7 @@ static void __exit ata_exit(void)
ata_release_transport(ata_scsi_transport_template);
libata_transport_exit();
ata_sff_exit();
+ ata_acpi_unregister();
kfree(ata_force_tbl);
}
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 77fc806..7d4535e 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -419,7 +419,7 @@ int ata_ering_map(struct ata_ering *ering,
return rc;
}
-int ata_ering_clear_cb(struct ata_ering_entry *ent, void *void_arg)
+static int ata_ering_clear_cb(struct ata_ering_entry *ent, void *void_arg)
{
ent->eflags |= ATA_EFLAG_OLD_ER;
return 0;
diff --git a/drivers/ata/libata-pmp.c b/drivers/ata/libata-pmp.c
index 21b80c5..61c59ee 100644
--- a/drivers/ata/libata-pmp.c
+++ b/drivers/ata/libata-pmp.c
@@ -529,8 +529,6 @@ int sata_pmp_attach(struct ata_device *dev)
ata_for_each_link(tlink, ap, EDGE)
sata_link_init_spd(tlink);
- ata_acpi_associate_sata_port(ap);
-
return 0;
fail:
@@ -570,8 +568,6 @@ static void sata_pmp_detach(struct ata_device *dev)
ap->nr_pmp_links = 0;
link->pmp = 0;
spin_unlock_irqrestore(ap->lock, flags);
-
- ata_acpi_associate_sata_port(ap);
}
/**
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 2222635..8ec81ca 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -3445,6 +3445,7 @@ void ata_scsi_scan_host(struct ata_port *ap, int sync)
if (!IS_ERR(sdev)) {
dev->sdev = sdev;
scsi_device_put(sdev);
+ ata_acpi_bind(dev);
} else {
dev->sdev = NULL;
}
@@ -3541,6 +3542,8 @@ static void ata_scsi_remove_dev(struct ata_device *dev)
mutex_lock(&ap->scsi_host->scan_mutex);
spin_lock_irqsave(ap->lock, flags);
+ ata_acpi_unbind(dev);
+
/* clearing dev->sdev is protected by host lock */
sdev = dev->sdev;
dev->sdev = NULL;
diff --git a/drivers/ata/libata-transport.c b/drivers/ata/libata-transport.c
index c341904..c04d393 100644
--- a/drivers/ata/libata-transport.c
+++ b/drivers/ata/libata-transport.c
@@ -232,7 +232,7 @@ static void ata_tport_release(struct device *dev)
* Returns:
* %1 if the device represents a ATA Port, %0 else
*/
-int ata_is_port(const struct device *dev)
+static int ata_is_port(const struct device *dev)
{
return dev->release == ata_tport_release;
}
@@ -355,7 +355,7 @@ static void ata_tlink_release(struct device *dev)
* Returns:
* %1 if the device represents a ATA link, %0 else
*/
-int ata_is_link(const struct device *dev)
+static int ata_is_link(const struct device *dev)
{
return dev->release == ata_tlink_release;
}
@@ -572,7 +572,7 @@ static void ata_tdev_release(struct device *dev)
* Returns:
* %1 if the device represents a ATA device, %0 else
*/
-int ata_is_ata_dev(const struct device *dev)
+static int ata_is_ata_dev(const struct device *dev)
{
return dev->release == ata_tdev_release;
}
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index 9d0fd0b..50e4dff 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -107,21 +107,22 @@ extern const char *sata_spd_string(unsigned int spd);
extern int ata_port_probe(struct ata_port *ap);
extern void __ata_port_probe(struct ata_port *ap);
+#define to_ata_port(d) container_of(d, struct ata_port, tdev)
+
/* libata-acpi.c */
#ifdef CONFIG_ATA_ACPI
extern unsigned int ata_acpi_gtf_filter;
-
-extern void ata_acpi_associate_sata_port(struct ata_port *ap);
-extern void ata_acpi_associate(struct ata_host *host);
extern void ata_acpi_dissociate(struct ata_host *host);
extern int ata_acpi_on_suspend(struct ata_port *ap);
extern void ata_acpi_on_resume(struct ata_port *ap);
extern int ata_acpi_on_devcfg(struct ata_device *dev);
extern void ata_acpi_on_disable(struct ata_device *dev);
extern void ata_acpi_set_state(struct ata_port *ap, pm_message_t state);
+extern int ata_acpi_register(void);
+extern void ata_acpi_unregister(void);
+extern void ata_acpi_bind(struct ata_device *dev);
+extern void ata_acpi_unbind(struct ata_device *dev);
#else
-static inline void ata_acpi_associate_sata_port(struct ata_port *ap) { }
-static inline void ata_acpi_associate(struct ata_host *host) { }
static inline void ata_acpi_dissociate(struct ata_host *host) { }
static inline int ata_acpi_on_suspend(struct ata_port *ap) { return 0; }
static inline void ata_acpi_on_resume(struct ata_port *ap) { }
@@ -129,6 +130,10 @@ static inline int ata_acpi_on_devcfg(struct ata_device *dev) { return 0; }
static inline void ata_acpi_on_disable(struct ata_device *dev) { }
static inline void ata_acpi_set_state(struct ata_port *ap,
pm_message_t state) { }
+static inline int ata_acpi_register(void) { return 0; }
+static inline void ata_acpi_unregister(void) { }
+static inline void ata_acpi_bind(struct ata_device *dev) { }
+static inline void ata_acpi_unbind(struct ata_device *dev) { }
#endif
/* libata-scsi.c */
diff --git a/drivers/ata/pata_acpi.c b/drivers/ata/pata_acpi.c
index 54145ed..09723b7 100644
--- a/drivers/ata/pata_acpi.c
+++ b/drivers/ata/pata_acpi.c
@@ -39,7 +39,7 @@ static int pacpi_pre_reset(struct ata_link *link, unsigned long deadline)
{
struct ata_port *ap = link->ap;
struct pata_acpi *acpi = ap->private_data;
- if (ap->acpi_handle == NULL || ata_acpi_gtm(ap, &acpi->gtm) < 0)
+ if (ata_ap_acpi_handle(ap) == NULL || ata_acpi_gtm(ap, &acpi->gtm) < 0)
return -ENODEV;
return ata_sff_prereset(link, deadline);
@@ -195,7 +195,7 @@ static int pacpi_port_start(struct ata_port *ap)
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct pata_acpi *acpi;
- if (ap->acpi_handle == NULL)
+ if (ata_ap_acpi_handle(ap) == NULL)
return -ENODEV;
acpi = ap->private_data = devm_kzalloc(&pdev->dev, sizeof(struct pata_acpi), GFP_KERNEL);
@@ -273,22 +273,10 @@ static struct pci_driver pacpi_pci_driver = {
#endif
};
-static int __init pacpi_init(void)
-{
- return pci_register_driver(&pacpi_pci_driver);
-}
-
-static void __exit pacpi_exit(void)
-{
- pci_unregister_driver(&pacpi_pci_driver);
-}
-
-module_init(pacpi_init);
-module_exit(pacpi_exit);
+module_pci_driver(pacpi_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for ATA in ACPI mode");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, pacpi_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index dc6b5da..82a0892 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -632,21 +632,10 @@ static struct pci_driver amd_pci_driver = {
#endif
};
-static int __init amd_init(void)
-{
- return pci_register_driver(&amd_pci_driver);
-}
-
-static void __exit amd_exit(void)
-{
- pci_unregister_driver(&amd_pci_driver);
-}
+module_pci_driver(amd_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for AMD and Nvidia PATA IDE");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, amd);
MODULE_VERSION(DRV_VERSION);
-
-module_init(amd_init);
-module_exit(amd_exit);
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
index 4b8b22e..74b215c 100644
--- a/drivers/ata/pata_artop.c
+++ b/drivers/ata/pata_artop.c
@@ -451,18 +451,7 @@ static struct pci_driver artop_pci_driver = {
#endif
};
-static int __init artop_init(void)
-{
- return pci_register_driver(&artop_pci_driver);
-}
-
-static void __exit artop_exit(void)
-{
- pci_unregister_driver(&artop_pci_driver);
-}
-
-module_init(artop_init);
-module_exit(artop_exit);
+module_pci_driver(artop_pci_driver);
MODULE_AUTHOR("Alan Cox, Bartlomiej Zolnierkiewicz");
MODULE_DESCRIPTION("SCSI low-level driver for ARTOP PATA");
diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
index be1aa14..361c75c 100644
--- a/drivers/ata/pata_atiixp.c
+++ b/drivers/ata/pata_atiixp.c
@@ -289,22 +289,10 @@ static struct pci_driver atiixp_pci_driver = {
#endif
};
-static int __init atiixp_init(void)
-{
- return pci_register_driver(&atiixp_pci_driver);
-}
-
-
-static void __exit atiixp_exit(void)
-{
- pci_unregister_driver(&atiixp_pci_driver);
-}
+module_pci_driver(atiixp_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for ATI IXP200/300/400");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, atiixp);
MODULE_VERSION(DRV_VERSION);
-
-module_init(atiixp_init);
-module_exit(atiixp_exit);
diff --git a/drivers/ata/pata_atp867x.c b/drivers/ata/pata_atp867x.c
index 3cfabb2..041f50d 100644
--- a/drivers/ata/pata_atp867x.c
+++ b/drivers/ata/pata_atp867x.c
@@ -565,21 +565,10 @@ static struct pci_driver atp867x_driver = {
#endif
};
-static int __init atp867x_init(void)
-{
- return pci_register_driver(&atp867x_driver);
-}
-
-static void __exit atp867x_exit(void)
-{
- pci_unregister_driver(&atp867x_driver);
-}
+module_pci_driver(atp867x_driver);
MODULE_AUTHOR("John(Jung-Ik) Lee, Google Inc.");
MODULE_DESCRIPTION("low level driver for Artop/Acard 867x ATA controller");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, atp867x_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
-module_init(atp867x_init);
-module_exit(atp867x_exit);
diff --git a/drivers/ata/pata_cmd640.c b/drivers/ata/pata_cmd640.c
index 549d28d..504b98b 100644
--- a/drivers/ata/pata_cmd640.c
+++ b/drivers/ata/pata_cmd640.c
@@ -263,21 +263,10 @@ static struct pci_driver cmd640_pci_driver = {
#endif
};
-static int __init cmd640_init(void)
-{
- return pci_register_driver(&cmd640_pci_driver);
-}
-
-static void __exit cmd640_exit(void)
-{
- pci_unregister_driver(&cmd640_pci_driver);
-}
+module_pci_driver(cmd640_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for CMD640 PATA controllers");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, cmd640);
MODULE_VERSION(DRV_VERSION);
-
-module_init(cmd640_init);
-module_exit(cmd640_exit);
diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c
index 1c17cd1..7ba0141 100644
--- a/drivers/ata/pata_cmd64x.c
+++ b/drivers/ata/pata_cmd64x.c
@@ -423,7 +423,7 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &cmd648_port_ops
}
};
- const struct ata_port_info *ppi[] = {
+ const struct ata_port_info *ppi[] = {
&cmd_info[id->driver_data],
&cmd_info[id->driver_data],
NULL
@@ -478,7 +478,7 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
if (port_ok && cntrl_ch0_ok && !(reg & CNTRL_CH0)) {
dev_printk(KERN_NOTICE, &pdev->dev, "Primary port is disabled\n");
ppi[0] = &ata_dummy_port_info;
-
+
}
if (port_ok && !(reg & CNTRL_CH1)) {
dev_printk(KERN_NOTICE, &pdev->dev, "Secondary port is disabled\n");
@@ -525,21 +525,10 @@ static struct pci_driver cmd64x_pci_driver = {
#endif
};
-static int __init cmd64x_init(void)
-{
- return pci_register_driver(&cmd64x_pci_driver);
-}
-
-static void __exit cmd64x_exit(void)
-{
- pci_unregister_driver(&cmd64x_pci_driver);
-}
+module_pci_driver(cmd64x_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for CMD64x series PATA controllers");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, cmd64x);
MODULE_VERSION(DRV_VERSION);
-
-module_init(cmd64x_init);
-module_exit(cmd64x_exit);
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c
index 9ddcddc..de74d80 100644
--- a/drivers/ata/pata_cs5520.c
+++ b/drivers/ata/pata_cs5520.c
@@ -302,22 +302,10 @@ static struct pci_driver cs5520_pci_driver = {
#endif
};
-static int __init cs5520_init(void)
-{
- return pci_register_driver(&cs5520_pci_driver);
-}
-
-static void __exit cs5520_exit(void)
-{
- pci_unregister_driver(&cs5520_pci_driver);
-}
+module_pci_driver(cs5520_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Cyrix CS5510/5520");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, pata_cs5520);
MODULE_VERSION(DRV_VERSION);
-
-module_init(cs5520_init);
-module_exit(cs5520_exit);
-
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
index f792330..48389ae 100644
--- a/drivers/ata/pata_cs5530.c
+++ b/drivers/ata/pata_cs5530.c
@@ -363,21 +363,10 @@ static struct pci_driver cs5530_pci_driver = {
#endif
};
-static int __init cs5530_init(void)
-{
- return pci_register_driver(&cs5530_pci_driver);
-}
-
-static void __exit cs5530_exit(void)
-{
- pci_unregister_driver(&cs5530_pci_driver);
-}
+module_pci_driver(cs5530_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the Cyrix/NS/AMD 5530");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, cs5530);
MODULE_VERSION(DRV_VERSION);
-
-module_init(cs5530_init);
-module_exit(cs5530_exit);
diff --git a/drivers/ata/pata_cs5535.c b/drivers/ata/pata_cs5535.c
index a0b4640..997e16a 100644
--- a/drivers/ata/pata_cs5535.c
+++ b/drivers/ata/pata_cs5535.c
@@ -207,21 +207,10 @@ static struct pci_driver cs5535_pci_driver = {
#endif
};
-static int __init cs5535_init(void)
-{
- return pci_register_driver(&cs5535_pci_driver);
-}
-
-static void __exit cs5535_exit(void)
-{
- pci_unregister_driver(&cs5535_pci_driver);
-}
+module_pci_driver(cs5535_pci_driver);
MODULE_AUTHOR("Alan Cox, Jens Altmann, Wolfgan Zuleger, Alexander Kiausch");
MODULE_DESCRIPTION("low-level driver for the NS/AMD 5535");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, cs5535);
MODULE_VERSION(DRV_VERSION);
-
-module_init(cs5535_init);
-module_exit(cs5535_exit);
diff --git a/drivers/ata/pata_cs5536.c b/drivers/ata/pata_cs5536.c
index 7a402c7..dec1b6c 100644
--- a/drivers/ata/pata_cs5536.c
+++ b/drivers/ata/pata_cs5536.c
@@ -274,21 +274,10 @@ static struct pci_driver cs5536_pci_driver = {
#endif
};
-static int __init cs5536_init(void)
-{
- return pci_register_driver(&cs5536_pci_driver);
-}
-
-static void __exit cs5536_exit(void)
-{
- pci_unregister_driver(&cs5536_pci_driver);
-}
+module_pci_driver(cs5536_pci_driver);
MODULE_AUTHOR("Martin K. Petersen");
MODULE_DESCRIPTION("low-level driver for the CS5536 IDE controller");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, cs5536);
MODULE_VERSION(DRV_VERSION);
-
-module_init(cs5536_init);
-module_exit(cs5536_exit);
diff --git a/drivers/ata/pata_cypress.c b/drivers/ata/pata_cypress.c
index 6d915b0..810bc99 100644
--- a/drivers/ata/pata_cypress.c
+++ b/drivers/ata/pata_cypress.c
@@ -158,23 +158,10 @@ static struct pci_driver cy82c693_pci_driver = {
#endif
};
-static int __init cy82c693_init(void)
-{
- return pci_register_driver(&cy82c693_pci_driver);
-}
-
-
-static void __exit cy82c693_exit(void)
-{
- pci_unregister_driver(&cy82c693_pci_driver);
-}
-
+module_pci_driver(cy82c693_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the CY82C693 PATA controller");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, cy82c693);
MODULE_VERSION(DRV_VERSION);
-
-module_init(cy82c693_init);
-module_exit(cy82c693_exit);
diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c
index f0243ed..3c12fd7 100644
--- a/drivers/ata/pata_efar.c
+++ b/drivers/ata/pata_efar.c
@@ -295,22 +295,10 @@ static struct pci_driver efar_pci_driver = {
#endif
};
-static int __init efar_init(void)
-{
- return pci_register_driver(&efar_pci_driver);
-}
-
-static void __exit efar_exit(void)
-{
- pci_unregister_driver(&efar_pci_driver);
-}
-
-module_init(efar_init);
-module_exit(efar_exit);
+module_pci_driver(efar_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for EFAR PIIX clones");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, efar_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index 42cffd3..4be884a 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -418,21 +418,10 @@ static struct pci_driver hpt36x_pci_driver = {
#endif
};
-static int __init hpt36x_init(void)
-{
- return pci_register_driver(&hpt36x_pci_driver);
-}
-
-static void __exit hpt36x_exit(void)
-{
- pci_unregister_driver(&hpt36x_pci_driver);
-}
+module_pci_driver(hpt36x_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, hpt36x);
MODULE_VERSION(DRV_VERSION);
-
-module_init(hpt36x_init);
-module_exit(hpt36x_exit);
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index 9620636..a9d74ef 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -1058,21 +1058,10 @@ static struct pci_driver hpt37x_pci_driver = {
.remove = ata_pci_remove_one
};
-static int __init hpt37x_init(void)
-{
- return pci_register_driver(&hpt37x_pci_driver);
-}
-
-static void __exit hpt37x_exit(void)
-{
- pci_unregister_driver(&hpt37x_pci_driver);
-}
+module_pci_driver(hpt37x_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the Highpoint HPT37x/30x");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, hpt37x);
MODULE_VERSION(DRV_VERSION);
-
-module_init(hpt37x_init);
-module_exit(hpt37x_exit);
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index 765f136..4be0398 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -621,21 +621,10 @@ static struct pci_driver hpt3x2n_pci_driver = {
.remove = ata_pci_remove_one
};
-static int __init hpt3x2n_init(void)
-{
- return pci_register_driver(&hpt3x2n_pci_driver);
-}
-
-static void __exit hpt3x2n_exit(void)
-{
- pci_unregister_driver(&hpt3x2n_pci_driver);
-}
+module_pci_driver(hpt3x2n_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the Highpoint HPT3xxN");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, hpt3x2n);
MODULE_VERSION(DRV_VERSION);
-
-module_init(hpt3x2n_init);
-module_exit(hpt3x2n_exit);
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
index b3042da..76c9314 100644
--- a/drivers/ata/pata_hpt3x3.c
+++ b/drivers/ata/pata_hpt3x3.c
@@ -284,23 +284,10 @@ static struct pci_driver hpt3x3_pci_driver = {
#endif
};
-static int __init hpt3x3_init(void)
-{
- return pci_register_driver(&hpt3x3_pci_driver);
-}
-
-
-static void __exit hpt3x3_exit(void)
-{
- pci_unregister_driver(&hpt3x3_pci_driver);
-}
-
+module_pci_driver(hpt3x3_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the Highpoint HPT343/363");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, hpt3x3);
MODULE_VERSION(DRV_VERSION);
-
-module_init(hpt3x3_init);
-module_exit(hpt3x3_exit);
diff --git a/drivers/ata/pata_imx.c b/drivers/ata/pata_imx.c
index c5af97f..87bb05b 100644
--- a/drivers/ata/pata_imx.c
+++ b/drivers/ata/pata_imx.c
@@ -118,7 +118,7 @@ static int __devinit pata_imx_probe(struct platform_device *pdev)
return PTR_ERR(priv->clk);
}
- clk_enable(priv->clk);
+ clk_prepare_enable(priv->clk);
host = ata_host_alloc(&pdev->dev, 1);
if (!host)
@@ -162,7 +162,7 @@ static int __devinit pata_imx_probe(struct platform_device *pdev)
&pata_imx_sht);
free_priv:
- clk_disable(priv->clk);
+ clk_disable_unprepare(priv->clk);
clk_put(priv->clk);
return -ENOMEM;
}
@@ -176,7 +176,7 @@ static int __devexit pata_imx_remove(struct platform_device *pdev)
__raw_writel(0, priv->host_regs + PATA_IMX_ATA_INT_EN);
- clk_disable(priv->clk);
+ clk_disable_unprepare(priv->clk);
clk_put(priv->clk);
return 0;
@@ -194,7 +194,7 @@ static int pata_imx_suspend(struct device *dev)
__raw_writel(0, priv->host_regs + PATA_IMX_ATA_INT_EN);
priv->ata_ctl =
__raw_readl(priv->host_regs + PATA_IMX_ATA_CONTROL);
- clk_disable(priv->clk);
+ clk_disable_unprepare(priv->clk);
}
return ret;
@@ -205,7 +205,7 @@ static int pata_imx_resume(struct device *dev)
struct ata_host *host = dev_get_drvdata(dev);
struct pata_imx_priv *priv = host->private_data;
- clk_enable(priv->clk);
+ clk_prepare_enable(priv->clk);
__raw_writel(priv->ata_ctl, priv->host_regs + PATA_IMX_ATA_CONTROL);
diff --git a/drivers/ata/pata_it8213.c b/drivers/ata/pata_it8213.c
index cf9164d..2a8dd95 100644
--- a/drivers/ata/pata_it8213.c
+++ b/drivers/ata/pata_it8213.c
@@ -290,18 +290,7 @@ static struct pci_driver it8213_pci_driver = {
#endif
};
-static int __init it8213_init(void)
-{
- return pci_register_driver(&it8213_pci_driver);
-}
-
-static void __exit it8213_exit(void)
-{
- pci_unregister_driver(&it8213_pci_driver);
-}
-
-module_init(it8213_init);
-module_exit(it8213_exit);
+module_pci_driver(it8213_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for the ITE 8213");
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
index 62c5d00..9cc05d8 100644
--- a/drivers/ata/pata_it821x.c
+++ b/drivers/ata/pata_it821x.c
@@ -972,15 +972,7 @@ static struct pci_driver it821x_pci_driver = {
#endif
};
-static int __init it821x_init(void)
-{
- return pci_register_driver(&it821x_pci_driver);
-}
-
-static void __exit it821x_exit(void)
-{
- pci_unregister_driver(&it821x_pci_driver);
-}
+module_pci_driver(it821x_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the IT8211/IT8212 IDE RAID controller");
@@ -988,9 +980,5 @@ MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, it821x);
MODULE_VERSION(DRV_VERSION);
-
module_param_named(noraid, it8212_noraid, int, S_IRUGO);
MODULE_PARM_DESC(noraid, "Force card into bypass mode");
-
-module_init(it821x_init);
-module_exit(it821x_exit);
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
index cb3babb..76e739b0 100644
--- a/drivers/ata/pata_jmicron.c
+++ b/drivers/ata/pata_jmicron.c
@@ -164,18 +164,7 @@ static struct pci_driver jmicron_pci_driver = {
#endif
};
-static int __init jmicron_init(void)
-{
- return pci_register_driver(&jmicron_pci_driver);
-}
-
-static void __exit jmicron_exit(void)
-{
- pci_unregister_driver(&jmicron_pci_driver);
-}
-
-module_init(jmicron_init);
-module_exit(jmicron_exit);
+module_pci_driver(jmicron_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for Jmicron PATA ports");
diff --git a/drivers/ata/pata_marvell.c b/drivers/ata/pata_marvell.c
index 5d7f58a..a4f5e78 100644
--- a/drivers/ata/pata_marvell.c
+++ b/drivers/ata/pata_marvell.c
@@ -178,22 +178,10 @@ static struct pci_driver marvell_pci_driver = {
#endif
};
-static int __init marvell_init(void)
-{
- return pci_register_driver(&marvell_pci_driver);
-}
-
-static void __exit marvell_exit(void)
-{
- pci_unregister_driver(&marvell_pci_driver);
-}
-
-module_init(marvell_init);
-module_exit(marvell_exit);
+module_pci_driver(marvell_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for Marvell ATA in legacy mode");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, marvell_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
diff --git a/drivers/ata/pata_mpiix.c b/drivers/ata/pata_mpiix.c
index 9dc16df..1f5f28b 100644
--- a/drivers/ata/pata_mpiix.c
+++ b/drivers/ata/pata_mpiix.c
@@ -230,21 +230,10 @@ static struct pci_driver mpiix_pci_driver = {
#endif
};
-static int __init mpiix_init(void)
-{
- return pci_register_driver(&mpiix_pci_driver);
-}
-
-static void __exit mpiix_exit(void)
-{
- pci_unregister_driver(&mpiix_pci_driver);
-}
+module_pci_driver(mpiix_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Intel MPIIX");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, mpiix);
MODULE_VERSION(DRV_VERSION);
-
-module_init(mpiix_init);
-module_exit(mpiix_exit);
diff --git a/drivers/ata/pata_netcell.c b/drivers/ata/pata_netcell.c
index 9979a43..ad1a0fe 100644
--- a/drivers/ata/pata_netcell.c
+++ b/drivers/ata/pata_netcell.c
@@ -99,22 +99,10 @@ static struct pci_driver netcell_pci_driver = {
#endif
};
-static int __init netcell_init(void)
-{
- return pci_register_driver(&netcell_pci_driver);
-}
-
-static void __exit netcell_exit(void)
-{
- pci_unregister_driver(&netcell_pci_driver);
-}
-
-module_init(netcell_init);
-module_exit(netcell_exit);
+module_pci_driver(netcell_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for Netcell PATA RAID");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, netcell_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
diff --git a/drivers/ata/pata_ninja32.c b/drivers/ata/pata_ninja32.c
index e277a14..12010ed 100644
--- a/drivers/ata/pata_ninja32.c
+++ b/drivers/ata/pata_ninja32.c
@@ -190,21 +190,10 @@ static struct pci_driver ninja32_pci_driver = {
#endif
};
-static int __init ninja32_init(void)
-{
- return pci_register_driver(&ninja32_pci_driver);
-}
-
-static void __exit ninja32_exit(void)
-{
- pci_unregister_driver(&ninja32_pci_driver);
-}
+module_pci_driver(ninja32_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Ninja32 ATA");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, ninja32);
MODULE_VERSION(DRV_VERSION);
-
-module_init(ninja32_init);
-module_exit(ninja32_exit);
diff --git a/drivers/ata/pata_ns87410.c b/drivers/ata/pata_ns87410.c
index 31d5986..0c424da 100644
--- a/drivers/ata/pata_ns87410.c
+++ b/drivers/ata/pata_ns87410.c
@@ -168,21 +168,10 @@ static struct pci_driver ns87410_pci_driver = {
#endif
};
-static int __init ns87410_init(void)
-{
- return pci_register_driver(&ns87410_pci_driver);
-}
-
-static void __exit ns87410_exit(void)
-{
- pci_unregister_driver(&ns87410_pci_driver);
-}
+module_pci_driver(ns87410_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Nat Semi 87410");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, ns87410);
MODULE_VERSION(DRV_VERSION);
-
-module_init(ns87410_init);
-module_exit(ns87410_exit);
diff --git a/drivers/ata/pata_ns87415.c b/drivers/ata/pata_ns87415.c
index f1d517b..6f6fa10 100644
--- a/drivers/ata/pata_ns87415.c
+++ b/drivers/ata/pata_ns87415.c
@@ -414,18 +414,7 @@ static struct pci_driver ns87415_pci_driver = {
#endif
};
-static int __init ns87415_init(void)
-{
- return pci_register_driver(&ns87415_pci_driver);
-}
-
-static void __exit ns87415_exit(void)
-{
- pci_unregister_driver(&ns87415_pci_driver);
-}
-
-module_init(ns87415_init);
-module_exit(ns87415_exit);
+module_pci_driver(ns87415_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("ATA low-level driver for NS87415 controllers");
diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c
index 98cdf50..d77b2e1 100644
--- a/drivers/ata/pata_oldpiix.c
+++ b/drivers/ata/pata_oldpiix.c
@@ -265,22 +265,10 @@ static struct pci_driver oldpiix_pci_driver = {
#endif
};
-static int __init oldpiix_init(void)
-{
- return pci_register_driver(&oldpiix_pci_driver);
-}
-
-static void __exit oldpiix_exit(void)
-{
- pci_unregister_driver(&oldpiix_pci_driver);
-}
-
-module_init(oldpiix_init);
-module_exit(oldpiix_exit);
+module_pci_driver(oldpiix_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for early PIIX series controllers");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, oldpiix_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c
index accc033..4ea70cd 100644
--- a/drivers/ata/pata_opti.c
+++ b/drivers/ata/pata_opti.c
@@ -191,22 +191,10 @@ static struct pci_driver opti_pci_driver = {
#endif
};
-static int __init opti_init(void)
-{
- return pci_register_driver(&opti_pci_driver);
-}
-
-static void __exit opti_exit(void)
-{
- pci_unregister_driver(&opti_pci_driver);
-}
-
+module_pci_driver(opti_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Opti 621/621X");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, opti);
MODULE_VERSION(DRV_VERSION);
-
-module_init(opti_init);
-module_exit(opti_exit);
diff --git a/drivers/ata/pata_optidma.c b/drivers/ata/pata_optidma.c
index 77cb914..78ede3f 100644
--- a/drivers/ata/pata_optidma.c
+++ b/drivers/ata/pata_optidma.c
@@ -447,21 +447,10 @@ static struct pci_driver optidma_pci_driver = {
#endif
};
-static int __init optidma_init(void)
-{
- return pci_register_driver(&optidma_pci_driver);
-}
-
-static void __exit optidma_exit(void)
-{
- pci_unregister_driver(&optidma_pci_driver);
-}
+module_pci_driver(optidma_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Opti Firestar/Firestar Plus");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, optidma);
MODULE_VERSION(DRV_VERSION);
-
-module_init(optidma_init);
-module_exit(optidma_exit);
diff --git a/drivers/ata/pata_pcmcia.c b/drivers/ata/pata_pcmcia.c
index a808ba0..958238d 100644
--- a/drivers/ata/pata_pcmcia.c
+++ b/drivers/ata/pata_pcmcia.c
@@ -170,7 +170,8 @@ static int pcmcia_check_one_config(struct pcmcia_device *pdev, void *priv_data)
{
int *is_kme = priv_data;
- if (!(pdev->resource[0]->flags & IO_DATA_PATH_WIDTH_8)) {
+ if ((pdev->resource[0]->flags & IO_DATA_PATH_WIDTH)
+ != IO_DATA_PATH_WIDTH_8) {
pdev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
pdev->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO;
}
diff --git a/drivers/ata/pata_pdc2027x.c b/drivers/ata/pata_pdc2027x.c
index 7d63f24..c9399c8 100644
--- a/drivers/ata/pata_pdc2027x.c
+++ b/drivers/ata/pata_pdc2027x.c
@@ -784,21 +784,4 @@ static int pdc2027x_reinit_one(struct pci_dev *pdev)
}
#endif
-/**
- * pdc2027x_init - Called after this module is loaded into the kernel.
- */
-static int __init pdc2027x_init(void)
-{
- return pci_register_driver(&pdc2027x_pci_driver);
-}
-
-/**
- * pdc2027x_exit - Called before this module unloaded from the kernel
- */
-static void __exit pdc2027x_exit(void)
-{
- pci_unregister_driver(&pdc2027x_pci_driver);
-}
-
-module_init(pdc2027x_init);
-module_exit(pdc2027x_exit);
+module_pci_driver(pdc2027x_pci_driver);
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c
index c2ed586..c34fc50 100644
--- a/drivers/ata/pata_pdc202xx_old.c
+++ b/drivers/ata/pata_pdc202xx_old.c
@@ -384,21 +384,10 @@ static struct pci_driver pdc202xx_pci_driver = {
#endif
};
-static int __init pdc202xx_init(void)
-{
- return pci_register_driver(&pdc202xx_pci_driver);
-}
-
-static void __exit pdc202xx_exit(void)
-{
- pci_unregister_driver(&pdc202xx_pci_driver);
-}
+module_pci_driver(pdc202xx_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Promise 2024x and 20262-20267");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, pdc202xx);
MODULE_VERSION(DRV_VERSION);
-
-module_init(pdc202xx_init);
-module_exit(pdc202xx_exit);
diff --git a/drivers/ata/pata_piccolo.c b/drivers/ata/pata_piccolo.c
index cb01bf9..2beb6b5 100644
--- a/drivers/ata/pata_piccolo.c
+++ b/drivers/ata/pata_piccolo.c
@@ -117,24 +117,10 @@ static struct pci_driver ata_tosh_pci_driver = {
#endif
};
-static int __init ata_tosh_init(void)
-{
- return pci_register_driver(&ata_tosh_pci_driver);
-}
-
-
-static void __exit ata_tosh_exit(void)
-{
- pci_unregister_driver(&ata_tosh_pci_driver);
-}
-
+module_pci_driver(ata_tosh_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("Low level driver for Toshiba Piccolo ATA");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, ata_tosh);
MODULE_VERSION(DRV_VERSION);
-
-module_init(ata_tosh_init);
-module_exit(ata_tosh_exit);
-
diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c
index b2d3a2b..f582ba1 100644
--- a/drivers/ata/pata_radisys.c
+++ b/drivers/ata/pata_radisys.c
@@ -244,22 +244,10 @@ static struct pci_driver radisys_pci_driver = {
#endif
};
-static int __init radisys_init(void)
-{
- return pci_register_driver(&radisys_pci_driver);
-}
-
-static void __exit radisys_exit(void)
-{
- pci_unregister_driver(&radisys_pci_driver);
-}
-
-module_init(radisys_init);
-module_exit(radisys_exit);
+module_pci_driver(radisys_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for Radisys R82600 controllers");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, radisys_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
diff --git a/drivers/ata/pata_rdc.c b/drivers/ata/pata_rdc.c
index e6a2dd7..32a3499 100644
--- a/drivers/ata/pata_rdc.c
+++ b/drivers/ata/pata_rdc.c
@@ -394,18 +394,7 @@ static struct pci_driver rdc_pci_driver = {
};
-static int __init rdc_init(void)
-{
- return pci_register_driver(&rdc_pci_driver);
-}
-
-static void __exit rdc_exit(void)
-{
- pci_unregister_driver(&rdc_pci_driver);
-}
-
-module_init(rdc_init);
-module_exit(rdc_exit);
+module_pci_driver(rdc_pci_driver);
MODULE_AUTHOR("Alan Cox (based on ata_piix)");
MODULE_DESCRIPTION("SCSI low-level driver for RDC PATA controllers");
diff --git a/drivers/ata/pata_rz1000.c b/drivers/ata/pata_rz1000.c
index aca321e..60f4de2 100644
--- a/drivers/ata/pata_rz1000.c
+++ b/drivers/ata/pata_rz1000.c
@@ -140,22 +140,10 @@ static struct pci_driver rz1000_pci_driver = {
#endif
};
-static int __init rz1000_init(void)
-{
- return pci_register_driver(&rz1000_pci_driver);
-}
-
-static void __exit rz1000_exit(void)
-{
- pci_unregister_driver(&rz1000_pci_driver);
-}
+module_pci_driver(rz1000_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for RZ1000 PCI ATA");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, pata_rz1000);
MODULE_VERSION(DRV_VERSION);
-
-module_init(rz1000_init);
-module_exit(rz1000_exit);
-
diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c
index c0e603a..ce2f828 100644
--- a/drivers/ata/pata_sc1200.c
+++ b/drivers/ata/pata_sc1200.c
@@ -261,21 +261,10 @@ static struct pci_driver sc1200_pci_driver = {
#endif
};
-static int __init sc1200_init(void)
-{
- return pci_register_driver(&sc1200_pci_driver);
-}
-
-static void __exit sc1200_exit(void)
-{
- pci_unregister_driver(&sc1200_pci_driver);
-}
+module_pci_driver(sc1200_pci_driver);
MODULE_AUTHOR("Alan Cox, Mark Lord");
MODULE_DESCRIPTION("low-level driver for the NS/AMD SC1200");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, sc1200);
MODULE_VERSION(DRV_VERSION);
-
-module_init(sc1200_init);
-module_exit(sc1200_exit);
diff --git a/drivers/ata/pata_scc.c b/drivers/ata/pata_scc.c
index e265f83..f35f15f 100644
--- a/drivers/ata/pata_scc.c
+++ b/drivers/ata/pata_scc.c
@@ -1103,26 +1103,7 @@ static struct pci_driver scc_pci_driver = {
#endif
};
-static int __init scc_init (void)
-{
- int rc;
-
- DPRINTK("pci_register_driver\n");
- rc = pci_register_driver(&scc_pci_driver);
- if (rc)
- return rc;
-
- DPRINTK("done\n");
- return 0;
-}
-
-static void __exit scc_exit (void)
-{
- pci_unregister_driver(&scc_pci_driver);
-}
-
-module_init(scc_init);
-module_exit(scc_exit);
+module_pci_driver(scc_pci_driver);
MODULE_AUTHOR("Toshiba corp");
MODULE_DESCRIPTION("SCSI low-level driver for Toshiba SCC PATA controller");
diff --git a/drivers/ata/pata_sch.c b/drivers/ata/pata_sch.c
index 7c78b99..db0d18c 100644
--- a/drivers/ata/pata_sch.c
+++ b/drivers/ata/pata_sch.c
@@ -179,15 +179,4 @@ static int __devinit sch_init_one(struct pci_dev *pdev,
return ata_pci_bmdma_init_one(pdev, ppi, &sch_sht, NULL, 0);
}
-static int __init sch_init(void)
-{
- return pci_register_driver(&sch_pci_driver);
-}
-
-static void __exit sch_exit(void)
-{
- pci_unregister_driver(&sch_pci_driver);
-}
-
-module_init(sch_init);
-module_exit(sch_exit);
+module_pci_driver(sch_pci_driver);
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c
index 71eaf38..f3febbc 100644
--- a/drivers/ata/pata_serverworks.c
+++ b/drivers/ata/pata_serverworks.c
@@ -475,21 +475,10 @@ static struct pci_driver serverworks_pci_driver = {
#endif
};
-static int __init serverworks_init(void)
-{
- return pci_register_driver(&serverworks_pci_driver);
-}
-
-static void __exit serverworks_exit(void)
-{
- pci_unregister_driver(&serverworks_pci_driver);
-}
+module_pci_driver(serverworks_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Serverworks OSB4/CSB5/CSB6");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, serverworks);
MODULE_VERSION(DRV_VERSION);
-
-module_init(serverworks_init);
-module_exit(serverworks_exit);
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index b92eacf..5cfdf94 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -437,21 +437,10 @@ static struct pci_driver sil680_pci_driver = {
#endif
};
-static int __init sil680_init(void)
-{
- return pci_register_driver(&sil680_pci_driver);
-}
-
-static void __exit sil680_exit(void)
-{
- pci_unregister_driver(&sil680_pci_driver);
-}
+module_pci_driver(sil680_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for SI680 PATA");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, sil680);
MODULE_VERSION(DRV_VERSION);
-
-module_init(sil680_init);
-module_exit(sil680_exit);
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index b0edc7d..2d5ac13 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -906,22 +906,10 @@ static struct pci_driver sis_pci_driver = {
#endif
};
-static int __init sis_init(void)
-{
- return pci_register_driver(&sis_pci_driver);
-}
-
-static void __exit sis_exit(void)
-{
- pci_unregister_driver(&sis_pci_driver);
-}
-
-module_init(sis_init);
-module_exit(sis_exit);
+module_pci_driver(sis_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for SiS ATA");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, sis_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index 24cf200..738e000 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -372,21 +372,10 @@ static struct pci_driver sl82c105_pci_driver = {
#endif
};
-static int __init sl82c105_init(void)
-{
- return pci_register_driver(&sl82c105_pci_driver);
-}
-
-static void __exit sl82c105_exit(void)
-{
- pci_unregister_driver(&sl82c105_pci_driver);
-}
+module_pci_driver(sl82c105_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Sl82c105");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, sl82c105);
MODULE_VERSION(DRV_VERSION);
-
-module_init(sl82c105_init);
-module_exit(sl82c105_exit);
diff --git a/drivers/ata/pata_triflex.c b/drivers/ata/pata_triflex.c
index 28da1c6..c8e589d 100644
--- a/drivers/ata/pata_triflex.c
+++ b/drivers/ata/pata_triflex.c
@@ -240,21 +240,10 @@ static struct pci_driver triflex_pci_driver = {
#endif
};
-static int __init triflex_init(void)
-{
- return pci_register_driver(&triflex_pci_driver);
-}
-
-static void __exit triflex_exit(void)
-{
- pci_unregister_driver(&triflex_pci_driver);
-}
+module_pci_driver(triflex_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Compaq Triflex");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, triflex);
MODULE_VERSION(DRV_VERSION);
-
-module_init(triflex_init);
-module_exit(triflex_exit);
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 255f336..8d2a9fd 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -711,21 +711,10 @@ static struct pci_driver via_pci_driver = {
#endif
};
-static int __init via_init(void)
-{
- return pci_register_driver(&via_pci_driver);
-}
-
-static void __exit via_exit(void)
-{
- pci_unregister_driver(&via_pci_driver);
-}
+module_pci_driver(via_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for VIA PATA");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, via);
MODULE_VERSION(DRV_VERSION);
-
-module_init(via_init);
-module_exit(via_exit);
diff --git a/drivers/ata/pdc_adma.c b/drivers/ata/pdc_adma.c
index 04911d5..5053333 100644
--- a/drivers/ata/pdc_adma.c
+++ b/drivers/ata/pdc_adma.c
@@ -660,21 +660,10 @@ static int adma_ata_init_one(struct pci_dev *pdev,
&adma_ata_sht);
}
-static int __init adma_ata_init(void)
-{
- return pci_register_driver(&adma_ata_pci_driver);
-}
-
-static void __exit adma_ata_exit(void)
-{
- pci_unregister_driver(&adma_ata_pci_driver);
-}
+module_pci_driver(adma_ata_pci_driver);
MODULE_AUTHOR("Mark Lord");
MODULE_DESCRIPTION("Pacific Digital Corporation ADMA low-level driver");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, adma_ata_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
-module_init(adma_ata_init);
-module_exit(adma_ata_exit);
diff --git a/drivers/ata/sata_dwc_460ex.c b/drivers/ata/sata_dwc_460ex.c
old mode 100644
new mode 100755
index 69f7cde..937aeb3
--- a/drivers/ata/sata_dwc_460ex.c
+++ b/drivers/ata/sata_dwc_460ex.c
@@ -158,6 +158,7 @@ enum {
/* Assign HW handshaking interface (x) to destination / source peripheral */
#define DMA_CFG_HW_HS_DEST(int_num) (((int_num) & 0xF) << 11)
#define DMA_CFG_HW_HS_SRC(int_num) (((int_num) & 0xF) << 7)
+#define DMA_CFG_HW_CH_PRIOR(int_num) (((int_num) & 0xF) << 5)
#define DMA_LLP_LMS(addr, master) (((addr) & 0xfffffffc) | (master))
/*
@@ -318,6 +319,7 @@ struct sata_dwc_host_priv {
u32 dma_interrupt_count;
struct ahb_dma_regs *sata_dma_regs;
struct device *dwc_dev;
+ int dma_channel;
};
struct sata_dwc_host_priv host_pvt;
/*
@@ -437,15 +439,12 @@ static void clear_chan_interrupts(int c)
*/
static int dma_request_channel(void)
{
- int i;
-
- for (i = 0; i < DMA_NUM_CHANS; i++) {
- if (!(in_le32(&(host_pvt.sata_dma_regs->dma_chan_en.low)) &\
- DMA_CHANNEL(i)))
- return i;
- }
- dev_err(host_pvt.dwc_dev, "%s NO channel chan_en: 0x%08x\n", __func__,
- in_le32(&(host_pvt.sata_dma_regs->dma_chan_en.low)));
+ /* Check if the channel is not currently in use */
+ if (!(in_le32(&(host_pvt.sata_dma_regs->dma_chan_en.low)) &
+ DMA_CHANNEL(host_pvt.dma_channel)))
+ return host_pvt.dma_channel;
+ dev_err(host_pvt.dwc_dev, "%s Channel %d is currently in use\n",
+ __func__, host_pvt.dma_channel);
return -1;
}
@@ -481,7 +480,8 @@ static irqreturn_t dma_dwc_interrupt(int irq, void *hsdev_instance)
dev_dbg(ap->dev, "eot=0x%08x err=0x%08x pending=%d active port=%d\n",
tfr_reg, err_reg, hsdevp->dma_pending[tag], port);
- for (chan = 0; chan < DMA_NUM_CHANS; chan++) {
+ chan = host_pvt.dma_channel;
+ if (chan >= 0) {
/* Check for end-of-transfer interrupt. */
if (tfr_reg & DMA_CHANNEL(chan)) {
/*
@@ -534,9 +534,9 @@ static irqreturn_t dma_dwc_interrupt(int irq, void *hsdev_instance)
static int dma_request_interrupts(struct sata_dwc_device *hsdev, int irq)
{
int retval = 0;
- int chan;
+ int chan = host_pvt.dma_channel;
- for (chan = 0; chan < DMA_NUM_CHANS; chan++) {
+ if (chan >= 0) {
/* Unmask error interrupt */
out_le32(&(host_pvt.sata_dma_regs)->interrupt_mask.error.low,
DMA_ENABLE_CHAN(chan));
@@ -575,7 +575,10 @@ static int map_sg_to_lli(struct scatterlist *sg, int num_elems,
int fis_len = 0;
dma_addr_t next_llp;
int bl;
+ int sms_val, dms_val;
+ sms_val = 0;
+ dms_val = 1 + host_pvt.dma_channel;
dev_dbg(host_pvt.dwc_dev, "%s: sg=%p nelem=%d lli=%p dma_lli=0x%08x"
" dmadr=0x%08x\n", __func__, sg, num_elems, lli, (u32)dma_lli,
(u32)dmadr_addr);
@@ -635,8 +638,8 @@ static int map_sg_to_lli(struct scatterlist *sg, int num_elems,
lli[idx].ctl.low = cpu_to_le32(
DMA_CTL_TTFC(DMA_CTL_TTFC_P2M_DMAC) |
- DMA_CTL_SMS(0) |
- DMA_CTL_DMS(1) |
+ DMA_CTL_SMS(sms_val) |
+ DMA_CTL_DMS(dms_val) |
DMA_CTL_SRC_MSIZE(bl) |
DMA_CTL_DST_MSIZE(bl) |
DMA_CTL_SINC_NOCHANGE |
@@ -651,8 +654,8 @@ static int map_sg_to_lli(struct scatterlist *sg, int num_elems,
lli[idx].ctl.low = cpu_to_le32(
DMA_CTL_TTFC(DMA_CTL_TTFC_M2P_PER) |
- DMA_CTL_SMS(1) |
- DMA_CTL_DMS(0) |
+ DMA_CTL_SMS(dms_val) |
+ DMA_CTL_DMS(sms_val) |
DMA_CTL_SRC_MSIZE(bl) |
DMA_CTL_DST_MSIZE(bl) |
DMA_CTL_DINC_NOCHANGE |
@@ -744,8 +747,10 @@ static int dma_dwc_xfer_setup(struct scatterlist *sg, int num_elems,
/* Program the CFG register. */
out_le32(&(host_pvt.sata_dma_regs->chan_regs[dma_ch].cfg.high),
+ DMA_CFG_HW_HS_SRC(dma_ch) | DMA_CFG_HW_HS_DEST(dma_ch) |
DMA_CFG_PROTCTL | DMA_CFG_FCMOD_REQ);
- out_le32(&(host_pvt.sata_dma_regs->chan_regs[dma_ch].cfg.low), 0);
+ out_le32(&(host_pvt.sata_dma_regs->chan_regs[dma_ch].cfg.low),
+ DMA_CFG_HW_CH_PRIOR(dma_ch));
/* Program the address of the linked list */
out_le32(&(host_pvt.sata_dma_regs->chan_regs[dma_ch].llp.low),
@@ -1581,10 +1586,31 @@ static void sata_dwc_qc_prep(struct ata_queued_cmd *qc)
static void sata_dwc_error_handler(struct ata_port *ap)
{
- ap->link.flags |= ATA_LFLAG_NO_HRST;
ata_sff_error_handler(ap);
}
+int sata_dwc_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
+{
+ struct sata_dwc_device *hsdev = HSDEV_FROM_AP(link->ap);
+ int ret;
+
+ ret = sata_sff_hardreset(link, class, deadline);
+
+ sata_dwc_enable_interrupts(hsdev);
+
+ /* Reconfigure the DMA control register */
+ out_le32(&hsdev->sata_dwc_regs->dmacr,
+ SATA_DWC_DMACR_TXRXCH_CLEAR);
+
+ /* Reconfigure the DMA Burst Transaction Size register */
+ out_le32(&hsdev->sata_dwc_regs->dbtsr,
+ SATA_DWC_DBTSR_MWR(AHB_DMA_BRST_DFLT) |
+ SATA_DWC_DBTSR_MRD(AHB_DMA_BRST_DFLT));
+
+ return ret;
+}
+
/*
* scsi mid-layer and libata interface structures
*/
@@ -1604,6 +1630,7 @@ static struct ata_port_operations sata_dwc_ops = {
.inherits = &ata_sff_port_ops,
.error_handler = sata_dwc_error_handler,
+ .hardreset = sata_dwc_hardreset,
.qc_prep = sata_dwc_qc_prep,
.qc_issue = sata_dwc_qc_issue,
@@ -1638,6 +1665,8 @@ static int sata_dwc_probe(struct platform_device *ofdev)
struct ata_host *host;
struct ata_port_info pi = sata_dwc_port_info[0];
const struct ata_port_info *ppi[] = { &pi, NULL };
+ struct device_node *np = ofdev->dev.of_node;
+ u32 dma_chan;
/* Allocate DWC SATA device */
hsdev = kzalloc(sizeof(*hsdev), GFP_KERNEL);
@@ -1647,6 +1676,13 @@ static int sata_dwc_probe(struct platform_device *ofdev)
goto error;
}
+ if (of_property_read_u32(np, "dma-channel", &dma_chan)) {
+ dev_warn(&ofdev->dev, "no dma-channel property set."
+ " Use channel 0\n");
+ dma_chan = 0;
+ }
+ host_pvt.dma_channel = dma_chan;
+
/* Ioremap SATA registers */
base = of_iomap(ofdev->dev.of_node, 0);
if (!base) {
diff --git a/drivers/ata/sata_inic162x.c b/drivers/ata/sata_inic162x.c
index 5c7d70c..dc35f4d 100644
--- a/drivers/ata/sata_inic162x.c
+++ b/drivers/ata/sata_inic162x.c
@@ -894,21 +894,10 @@ static struct pci_driver inic_pci_driver = {
.remove = ata_pci_remove_one,
};
-static int __init inic_init(void)
-{
- return pci_register_driver(&inic_pci_driver);
-}
-
-static void __exit inic_exit(void)
-{
- pci_unregister_driver(&inic_pci_driver);
-}
+module_pci_driver(inic_pci_driver);
MODULE_AUTHOR("Tejun Heo");
MODULE_DESCRIPTION("low-level driver for Initio 162x SATA");
MODULE_LICENSE("GPL v2");
MODULE_DEVICE_TABLE(pci, inic_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
-module_init(inic_init);
-module_exit(inic_exit);
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 55d6179..85ee499 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -2510,22 +2510,11 @@ static void nv_adma_host_stop(struct ata_host *host)
nv_ck804_host_stop(host);
}
-static int __init nv_init(void)
-{
- return pci_register_driver(&nv_pci_driver);
-}
-
-static void __exit nv_exit(void)
-{
- pci_unregister_driver(&nv_pci_driver);
-}
+module_pci_driver(nv_pci_driver);
-module_init(nv_init);
-module_exit(nv_exit);
module_param_named(adma, adma_enabled, bool, 0444);
MODULE_PARM_DESC(adma, "Enable use of ADMA (Default: false)");
module_param_named(swncq, swncq_enabled, bool, 0444);
MODULE_PARM_DESC(swncq, "Enable use of SWNCQ (Default: true)");
module_param_named(msi, msi_enabled, bool, 0444);
MODULE_PARM_DESC(msi, "Enable use of MSI (Default: false)");
-
diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c
index 000fcc9..489c817 100644
--- a/drivers/ata/sata_promise.c
+++ b/drivers/ata/sata_promise.c
@@ -1249,21 +1249,10 @@ static int pdc_ata_init_one(struct pci_dev *pdev,
&pdc_ata_sht);
}
-static int __init pdc_ata_init(void)
-{
- return pci_register_driver(&pdc_ata_pci_driver);
-}
-
-static void __exit pdc_ata_exit(void)
-{
- pci_unregister_driver(&pdc_ata_pci_driver);
-}
+module_pci_driver(pdc_ata_pci_driver);
MODULE_AUTHOR("Jeff Garzik");
MODULE_DESCRIPTION("Promise ATA TX2/TX4/TX4000 low-level driver");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, pdc_ata_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
-module_init(pdc_ata_init);
-module_exit(pdc_ata_exit);
diff --git a/drivers/ata/sata_qstor.c b/drivers/ata/sata_qstor.c
index 9d1a47b..3b0dd57 100644
--- a/drivers/ata/sata_qstor.c
+++ b/drivers/ata/sata_qstor.c
@@ -635,21 +635,10 @@ static int qs_ata_init_one(struct pci_dev *pdev,
&qs_ata_sht);
}
-static int __init qs_ata_init(void)
-{
- return pci_register_driver(&qs_ata_pci_driver);
-}
-
-static void __exit qs_ata_exit(void)
-{
- pci_unregister_driver(&qs_ata_pci_driver);
-}
+module_pci_driver(qs_ata_pci_driver);
MODULE_AUTHOR("Mark Lord");
MODULE_DESCRIPTION("Pacific Digital Corporation QStor SATA low-level driver");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, qs_ata_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
-module_init(qs_ata_init);
-module_exit(qs_ata_exit);
diff --git a/drivers/ata/sata_sil.c b/drivers/ata/sata_sil.c
index 9dfb40b..a7b3167 100644
--- a/drivers/ata/sata_sil.c
+++ b/drivers/ata/sata_sil.c
@@ -819,16 +819,4 @@ static int sil_pci_device_resume(struct pci_dev *pdev)
}
#endif
-static int __init sil_init(void)
-{
- return pci_register_driver(&sil_pci_driver);
-}
-
-static void __exit sil_exit(void)
-{
- pci_unregister_driver(&sil_pci_driver);
-}
-
-
-module_init(sil_init);
-module_exit(sil_exit);
+module_pci_driver(sil_pci_driver);
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index e7e610a..a5f2a56 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -1382,20 +1382,9 @@ static int sil24_port_resume(struct ata_port *ap)
}
#endif
-static int __init sil24_init(void)
-{
- return pci_register_driver(&sil24_pci_driver);
-}
-
-static void __exit sil24_exit(void)
-{
- pci_unregister_driver(&sil24_pci_driver);
-}
+module_pci_driver(sil24_pci_driver);
MODULE_AUTHOR("Tejun Heo");
MODULE_DESCRIPTION("Silicon Image 3124/3132 SATA low-level driver");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, sil24_pci_tbl);
-
-module_init(sil24_init);
-module_exit(sil24_exit);
diff --git a/drivers/ata/sata_sis.c b/drivers/ata/sata_sis.c
index 95ec435..fe3ca09 100644
--- a/drivers/ata/sata_sis.c
+++ b/drivers/ata/sata_sis.c
@@ -308,15 +308,4 @@ static int sis_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
IRQF_SHARED, &sis_sht);
}
-static int __init sis_init(void)
-{
- return pci_register_driver(&sis_pci_driver);
-}
-
-static void __exit sis_exit(void)
-{
- pci_unregister_driver(&sis_pci_driver);
-}
-
-module_init(sis_init);
-module_exit(sis_exit);
+module_pci_driver(sis_pci_driver);
diff --git a/drivers/ata/sata_svw.c b/drivers/ata/sata_svw.c
index c646118..44a4256 100644
--- a/drivers/ata/sata_svw.c
+++ b/drivers/ata/sata_svw.c
@@ -525,21 +525,10 @@ static struct pci_driver k2_sata_pci_driver = {
.remove = ata_pci_remove_one,
};
-static int __init k2_sata_init(void)
-{
- return pci_register_driver(&k2_sata_pci_driver);
-}
-
-static void __exit k2_sata_exit(void)
-{
- pci_unregister_driver(&k2_sata_pci_driver);
-}
+module_pci_driver(k2_sata_pci_driver);
MODULE_AUTHOR("Benjamin Herrenschmidt");
MODULE_DESCRIPTION("low-level driver for K2 SATA controller");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, k2_sata_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
-module_init(k2_sata_init);
-module_exit(k2_sata_exit);
diff --git a/drivers/ata/sata_sx4.c b/drivers/ata/sata_sx4.c
index cdaebbe..1226055 100644
--- a/drivers/ata/sata_sx4.c
+++ b/drivers/ata/sata_sx4.c
@@ -1498,24 +1498,10 @@ static int pdc_sata_init_one(struct pci_dev *pdev,
IRQF_SHARED, &pdc_sata_sht);
}
-
-static int __init pdc_sata_init(void)
-{
- return pci_register_driver(&pdc_sata_pci_driver);
-}
-
-
-static void __exit pdc_sata_exit(void)
-{
- pci_unregister_driver(&pdc_sata_pci_driver);
-}
-
+module_pci_driver(pdc_sata_pci_driver);
MODULE_AUTHOR("Jeff Garzik");
MODULE_DESCRIPTION("Promise SATA low-level driver");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, pdc_sata_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
-module_init(pdc_sata_init);
-module_exit(pdc_sata_exit);
diff --git a/drivers/ata/sata_uli.c b/drivers/ata/sata_uli.c
index b54ebfc..6d64891 100644
--- a/drivers/ata/sata_uli.c
+++ b/drivers/ata/sata_uli.c
@@ -243,16 +243,4 @@ static int uli_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
IRQF_SHARED, &uli_sht);
}
-static int __init uli_init(void)
-{
- return pci_register_driver(&uli_pci_driver);
-}
-
-static void __exit uli_exit(void)
-{
- pci_unregister_driver(&uli_pci_driver);
-}
-
-
-module_init(uli_init);
-module_exit(uli_exit);
+module_pci_driver(uli_pci_driver);
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index f93e43b..5913ea9 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -655,15 +655,4 @@ static int svia_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
IRQF_SHARED, &svia_sht);
}
-static int __init svia_init(void)
-{
- return pci_register_driver(&svia_pci_driver);
-}
-
-static void __exit svia_exit(void)
-{
- pci_unregister_driver(&svia_pci_driver);
-}
-
-module_init(svia_init);
-module_exit(svia_exit);
+module_pci_driver(svia_pci_driver);
diff --git a/drivers/ata/sata_vsc.c b/drivers/ata/sata_vsc.c
index 6135a52..e8cf88ba 100644
--- a/drivers/ata/sata_vsc.c
+++ b/drivers/ata/sata_vsc.c
@@ -436,21 +436,10 @@ static struct pci_driver vsc_sata_pci_driver = {
.remove = ata_pci_remove_one,
};
-static int __init vsc_sata_init(void)
-{
- return pci_register_driver(&vsc_sata_pci_driver);
-}
-
-static void __exit vsc_sata_exit(void)
-{
- pci_unregister_driver(&vsc_sata_pci_driver);
-}
+module_pci_driver(vsc_sata_pci_driver);
MODULE_AUTHOR("Jeremy Higdon");
MODULE_DESCRIPTION("low-level driver for Vitesse VSC7174 SATA controller");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, vsc_sata_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-
-module_init(vsc_sata_init);
-module_exit(vsc_sata_exit);
diff --git a/drivers/scsi/scsi_lib.c b/drivers/scsi/scsi_lib.c
index b583277..ffd7773 100644
--- a/drivers/scsi/scsi_lib.c
+++ b/drivers/scsi/scsi_lib.c
@@ -68,6 +68,23 @@ static struct scsi_host_sg_pool scsi_sg_pools[] = {
struct kmem_cache *scsi_sdb_cache;
+#ifdef CONFIG_ACPI
+#include <acpi/acpi_bus.h>
+
+int scsi_register_acpi_bus_type(struct acpi_bus_type *bus)
+{
+ bus->bus = &scsi_bus_type;
+ return register_acpi_bus_type(bus);
+}
+EXPORT_SYMBOL_GPL(scsi_register_acpi_bus_type);
+
+void scsi_unregister_acpi_bus_type(struct acpi_bus_type *bus)
+{
+ unregister_acpi_bus_type(bus);
+}
+EXPORT_SYMBOL_GPL(scsi_unregister_acpi_bus_type);
+#endif
+
/*
* When to reinvoke queueing after a resource shortage. It's 3 msecs to
* not change behaviour from the previous unplug mechanism, experimentation
diff --git a/include/linux/ata.h b/include/linux/ata.h
index 32df2b6..5713d3a 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -578,6 +578,7 @@ static inline int ata_is_data(u8 prot)
((u64) (id)[(n) + 0]) )
#define ata_id_cdb_intr(id) (((id)[ATA_ID_CONFIG] & 0x60) == 0x20)
+#define ata_id_has_da(id) ((id)[77] & (1 << 4))
static inline bool ata_id_has_hipm(const u16 *id)
{
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 53da442..64f90e1 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -161,6 +161,8 @@ enum {
ATA_DFLAG_DETACH = (1 << 24),
ATA_DFLAG_DETACHED = (1 << 25),
+ ATA_DFLAG_DA = (1 << 26), /* device supports Device Attention */
+
ATA_DEV_UNKNOWN = 0, /* unknown device */
ATA_DEV_ATA = 1, /* ATA device */
ATA_DEV_ATA_UNSUP = 2, /* ATA device (unsupported) */
@@ -545,9 +547,6 @@ struct ata_host {
struct mutex eh_mutex;
struct task_struct *eh_owner;
-#ifdef CONFIG_ATA_ACPI
- acpi_handle acpi_handle;
-#endif
struct ata_port *simplex_claimed; /* channel owning the DMA */
struct ata_port *ports[0];
};
@@ -615,7 +614,6 @@ struct ata_device {
struct scsi_device *sdev; /* attached SCSI device */
void *private_data;
#ifdef CONFIG_ATA_ACPI
- acpi_handle acpi_handle;
union acpi_object *gtf_cache;
unsigned int gtf_filter;
#endif
@@ -797,7 +795,6 @@ struct ata_port {
void *private_data;
#ifdef CONFIG_ATA_ACPI
- acpi_handle acpi_handle;
struct ata_acpi_gtm __acpi_init_gtm; /* use ata_acpi_init_gtm() */
#endif
/* owned by EH */
@@ -1116,6 +1113,8 @@ int ata_acpi_stm(struct ata_port *ap, const struct ata_acpi_gtm *stm);
int ata_acpi_gtm(struct ata_port *ap, struct ata_acpi_gtm *stm);
unsigned long ata_acpi_gtm_xfermask(struct ata_device *dev,
const struct ata_acpi_gtm *gtm);
+acpi_handle ata_ap_acpi_handle(struct ata_port *ap);
+acpi_handle ata_dev_acpi_handle(struct ata_device *dev);
int ata_acpi_cbl_80wire(struct ata_port *ap, const struct ata_acpi_gtm *gtm);
#else
static inline const struct ata_acpi_gtm *ata_acpi_init_gtm(struct ata_port *ap)
diff --git a/include/scsi/scsi.h b/include/scsi/scsi.h
index c6f0974..66216c1 100644
--- a/include/scsi/scsi.h
+++ b/include/scsi/scsi.h
@@ -216,6 +216,16 @@ scsi_command_size(const unsigned char *cmnd)
scsi_varlen_cdb_length(cmnd) : COMMAND_SIZE(cmnd[0]);
}
+#ifdef CONFIG_ACPI
+struct acpi_bus_type;
+
+extern int
+scsi_register_acpi_bus_type(struct acpi_bus_type *bus);
+
+extern void
+scsi_unregister_acpi_bus_type(struct acpi_bus_type *bus);
+#endif
+
/*
* SCSI Architecture Model (SAM) Status codes. Taken from SAM-3 draft
* T10/1561-D Revision 4 Draft dated 7th November 2002.
diff --git a/include/scsi/scsi_device.h b/include/scsi/scsi_device.h
index 7539f52..9895f69 100644
--- a/include/scsi/scsi_device.h
+++ b/include/scsi/scsi_device.h
@@ -154,6 +154,7 @@ struct scsi_device {
unsigned no_read_capacity_16:1; /* Avoid READ_CAPACITY_16 cmds */
unsigned try_rc_10_first:1; /* Try READ_CAPACACITY_10 first */
unsigned is_visible:1; /* is the device visible in sysfs */
+ unsigned can_power_off:1; /* Device supports runtime power off */
unsigned wce_default_on:1; /* Cache is ON by default */
DECLARE_BITMAP(supported_events, SDEV_EVT_MAXBITS); /* supported events */
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2011-01-28 8:29 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2011-01-28 8:29 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
1. DMA alignment fix for PIO + ATAPI.
2. various other minor fixes and PCI IDs
3. And a couple pata_hpt* cosmetics.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/ahci.c | 3 +
drivers/ata/libata-core.c | 1 +
drivers/ata/libata-scsi.c | 24 +++++++--
drivers/ata/pata_hpt366.c | 6 +-
drivers/ata/pata_hpt37x.c | 112 +++++++++++++++++++++-----------------------
drivers/ata/pata_hpt3x2n.c | 12 ++---
drivers/ata/pata_mpc52xx.c | 2 +-
7 files changed, 85 insertions(+), 75 deletions(-)
Anssi Hannula (1):
ahci: add HFLAG_YES_FBS and apply it to 88SE9128
Francesco Antonacci (1):
libata: DVR-212D can't do SETXFER DVD-RW DVR-212D
Sergei Shtylyov (4):
pata_hpt{366|37x}: use pr_warning(...) instead of printk(KERN_WARNING ...)
pata_hpt{37x|3x2n}: use pr_*(DRV_NAME ...) instead of printk(KERN_* ...)
pata_hpt37x: fold 'if' statement into 'switch'
pata_hpt37x: inherit prereset() method for HPT374
Seth Heasley (1):
ahci: AHCI mode SATA patch for Intel DH89xxCC DeviceIDs
Tejun Heo (2):
pata_mpc52xx: inherit from ata_bmdma_port_ops
libata: set queue DMA alignment to sector size for ATAPI too
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 3288263..b8d96ce 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -260,6 +260,7 @@ static const struct pci_device_id ahci_pci_tbl[] = {
{ PCI_VDEVICE(INTEL, 0x1d02), board_ahci }, /* PBG AHCI */
{ PCI_VDEVICE(INTEL, 0x1d04), board_ahci }, /* PBG RAID */
{ PCI_VDEVICE(INTEL, 0x1d06), board_ahci }, /* PBG RAID */
+ { PCI_VDEVICE(INTEL, 0x2323), board_ahci }, /* DH89xxCC AHCI */
/* JMicron 360/1/3/5/6, match class to avoid IDE function */
{ PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
@@ -379,6 +380,8 @@ static const struct pci_device_id ahci_pci_tbl[] = {
{ PCI_VDEVICE(MARVELL, 0x6145), board_ahci_mv }, /* 6145 */
{ PCI_VDEVICE(MARVELL, 0x6121), board_ahci_mv }, /* 6121 */
{ PCI_DEVICE(0x1b4b, 0x9123),
+ .class = PCI_CLASS_STORAGE_SATA_AHCI,
+ .class_mask = 0xffffff,
.driver_data = board_ahci_yes_fbs }, /* 88se9128 */
/* Promise */
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index a31fe96..d4e52e2 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -4138,6 +4138,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
* device and controller are SATA.
*/
{ "PIONEER DVD-RW DVRTD08", "1.00", ATA_HORKAGE_NOSETXFER },
+ { "PIONEER DVD-RW DVR-212D", "1.28", ATA_HORKAGE_NOSETXFER },
/* End Marker */
{ }
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 5defc74..600f635 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -1099,9 +1099,9 @@ static int ata_scsi_dev_config(struct scsi_device *sdev,
struct request_queue *q = sdev->request_queue;
void *buf;
- /* set the min alignment and padding */
- blk_queue_update_dma_alignment(sdev->request_queue,
- ATA_DMA_PAD_SZ - 1);
+ sdev->sector_size = ATA_SECT_SIZE;
+
+ /* set DMA padding */
blk_queue_update_dma_pad(sdev->request_queue,
ATA_DMA_PAD_SZ - 1);
@@ -1115,13 +1115,25 @@ static int ata_scsi_dev_config(struct scsi_device *sdev,
blk_queue_dma_drain(q, atapi_drain_needed, buf, ATAPI_MAX_DRAIN);
} else {
- /* ATA devices must be sector aligned */
sdev->sector_size = ata_id_logical_sector_size(dev->id);
- blk_queue_update_dma_alignment(sdev->request_queue,
- sdev->sector_size - 1);
sdev->manage_start_stop = 1;
}
+ /*
+ * ata_pio_sectors() expects buffer for each sector to not cross
+ * page boundary. Enforce it by requiring buffers to be sector
+ * aligned, which works iff sector_size is not larger than
+ * PAGE_SIZE. ATAPI devices also need the alignment as
+ * IDENTIFY_PACKET is executed as ATA_PROT_PIO.
+ */
+ if (sdev->sector_size > PAGE_SIZE)
+ ata_dev_printk(dev, KERN_WARNING,
+ "sector_size=%u > PAGE_SIZE, PIO may malfunction\n",
+ sdev->sector_size);
+
+ blk_queue_update_dma_alignment(sdev->request_queue,
+ sdev->sector_size - 1);
+
if (dev->flags & ATA_DFLAG_AN)
set_bit(SDEV_EVT_MEDIA_CHANGE, sdev->supported_events);
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index d7e57db..538ec38 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -25,7 +25,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt366"
-#define DRV_VERSION "0.6.9"
+#define DRV_VERSION "0.6.10"
struct hpt_clock {
u8 xfer_mode;
@@ -160,8 +160,8 @@ static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr,
while (list[i] != NULL) {
if (!strcmp(list[i], model_num)) {
- printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n",
- modestr, list[i]);
+ pr_warning(DRV_NAME ": %s is not supported for %s.\n",
+ modestr, list[i]);
return 1;
}
i++;
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index efdd18b..4c5b518 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -24,7 +24,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt37x"
-#define DRV_VERSION "0.6.18"
+#define DRV_VERSION "0.6.22"
struct hpt_clock {
u8 xfer_speed;
@@ -229,8 +229,8 @@ static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr,
while (list[i] != NULL) {
if (!strcmp(list[i], model_num)) {
- printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n",
- modestr, list[i]);
+ pr_warning(DRV_NAME ": %s is not supported for %s.\n",
+ modestr, list[i]);
return 1;
}
i++;
@@ -642,7 +642,6 @@ static struct ata_port_operations hpt372_port_ops = {
static struct ata_port_operations hpt374_fn1_port_ops = {
.inherits = &hpt372_port_ops,
.cable_detect = hpt374_fn1_cable_detect,
- .prereset = hpt37x_pre_reset,
};
/**
@@ -803,7 +802,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.udma_mask = ATA_UDMA6,
.port_ops = &hpt302_port_ops
};
- /* HPT374 - UDMA100, function 1 uses different prereset method */
+ /* HPT374 - UDMA100, function 1 uses different cable_detect method */
static const struct ata_port_info info_hpt374_fn0 = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
@@ -838,7 +837,8 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
if (rc)
return rc;
- if (dev->device == PCI_DEVICE_ID_TTI_HPT366) {
+ switch (dev->device) {
+ case PCI_DEVICE_ID_TTI_HPT366:
/* May be a later chip in disguise. Check */
/* Older chips are in the HPT366 driver. Ignore them */
if (rev < 3)
@@ -863,54 +863,50 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
chip_table = &hpt372;
break;
default:
- printk(KERN_ERR "pata_hpt37x: Unknown HPT366 subtype, "
+ pr_err(DRV_NAME ": Unknown HPT366 subtype, "
"please report (%d).\n", rev);
return -ENODEV;
}
- } else {
- switch (dev->device) {
- case PCI_DEVICE_ID_TTI_HPT372:
- /* 372N if rev >= 2 */
- if (rev >= 2)
- return -ENODEV;
- ppi[0] = &info_hpt372;
- chip_table = &hpt372a;
- break;
- case PCI_DEVICE_ID_TTI_HPT302:
- /* 302N if rev > 1 */
- if (rev > 1)
- return -ENODEV;
- ppi[0] = &info_hpt302;
- /* Check this */
- chip_table = &hpt302;
- break;
- case PCI_DEVICE_ID_TTI_HPT371:
- if (rev > 1)
- return -ENODEV;
- ppi[0] = &info_hpt302;
- chip_table = &hpt371;
- /*
- * Single channel device, master is not present
- * but the BIOS (or us for non x86) must mark it
- * absent
- */
- pci_read_config_byte(dev, 0x50, &mcr1);
- mcr1 &= ~0x04;
- pci_write_config_byte(dev, 0x50, mcr1);
- break;
- case PCI_DEVICE_ID_TTI_HPT374:
- chip_table = &hpt374;
- if (!(PCI_FUNC(dev->devfn) & 1))
- *ppi = &info_hpt374_fn0;
- else
- *ppi = &info_hpt374_fn1;
- break;
- default:
- printk(KERN_ERR
- "pata_hpt37x: PCI table is bogus, please report (%d).\n",
- dev->device);
- return -ENODEV;
- }
+ break;
+ case PCI_DEVICE_ID_TTI_HPT372:
+ /* 372N if rev >= 2 */
+ if (rev >= 2)
+ return -ENODEV;
+ ppi[0] = &info_hpt372;
+ chip_table = &hpt372a;
+ break;
+ case PCI_DEVICE_ID_TTI_HPT302:
+ /* 302N if rev > 1 */
+ if (rev > 1)
+ return -ENODEV;
+ ppi[0] = &info_hpt302;
+ /* Check this */
+ chip_table = &hpt302;
+ break;
+ case PCI_DEVICE_ID_TTI_HPT371:
+ if (rev > 1)
+ return -ENODEV;
+ ppi[0] = &info_hpt302;
+ chip_table = &hpt371;
+ /*
+ * Single channel device, master is not present but the BIOS
+ * (or us for non x86) must mark it absent
+ */
+ pci_read_config_byte(dev, 0x50, &mcr1);
+ mcr1 &= ~0x04;
+ pci_write_config_byte(dev, 0x50, mcr1);
+ break;
+ case PCI_DEVICE_ID_TTI_HPT374:
+ chip_table = &hpt374;
+ if (!(PCI_FUNC(dev->devfn) & 1))
+ *ppi = &info_hpt374_fn0;
+ else
+ *ppi = &info_hpt374_fn1;
+ break;
+ default:
+ pr_err(DRV_NAME ": PCI table is bogus, please report (%d).\n",
+ dev->device);
+ return -ENODEV;
}
/* Ok so this is a chip we support */
@@ -957,8 +953,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
u8 sr;
u32 total = 0;
- printk(KERN_WARNING
- "pata_hpt37x: BIOS has not set timing clocks.\n");
+ pr_warning(DRV_NAME ": BIOS has not set timing clocks.\n");
/* This is the process the HPT371 BIOS is reported to use */
for (i = 0; i < 128; i++) {
@@ -1014,7 +1009,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
(f_high << 16) | f_low | 0x100);
}
if (adjust == 8) {
- printk(KERN_ERR "pata_hpt37x: DPLL did not stabilize!\n");
+ pr_err(DRV_NAME ": DPLL did not stabilize!\n");
return -ENODEV;
}
if (dpll == 3)
@@ -1022,8 +1017,8 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
else
private_data = (void *)hpt37x_timings_50;
- printk(KERN_INFO "pata_hpt37x: bus clock %dMHz, using %dMHz DPLL.\n",
- MHz[clock_slot], MHz[dpll]);
+ pr_info(DRV_NAME ": bus clock %dMHz, using %dMHz DPLL.\n",
+ MHz[clock_slot], MHz[dpll]);
} else {
private_data = (void *)chip_table->clocks[clock_slot];
/*
@@ -1036,8 +1031,9 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
ppi[0] = &info_hpt370_33;
if (clock_slot < 2 && ppi[0] == &info_hpt370a)
ppi[0] = &info_hpt370a_33;
- printk(KERN_INFO "pata_hpt37x: %s using %dMHz bus clock.\n",
- chip_table->name, MHz[clock_slot]);
+
+ pr_info(DRV_NAME ": %s using %dMHz bus clock.\n",
+ chip_table->name, MHz[clock_slot]);
}
/* Now kick off ATA set up */
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index d2239bb..eca68ca 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -25,7 +25,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x2n"
-#define DRV_VERSION "0.3.13"
+#define DRV_VERSION "0.3.14"
enum {
HPT_PCI_FAST = (1 << 31),
@@ -418,7 +418,7 @@ static int hpt3x2n_pci_clock(struct pci_dev *pdev)
u16 sr;
u32 total = 0;
- printk(KERN_WARNING "pata_hpt3x2n: BIOS clock data not set.\n");
+ pr_warning(DRV_NAME ": BIOS clock data not set.\n");
/* This is the process the HPT371 BIOS is reported to use */
for (i = 0; i < 128; i++) {
@@ -528,8 +528,7 @@ hpt372n:
ppi[0] = &info_hpt372n;
break;
default:
- printk(KERN_ERR
- "pata_hpt3x2n: PCI table is bogus please report (%d).\n",
+ pr_err(DRV_NAME ": PCI table is bogus, please report (%d).\n",
dev->device);
return -ENODEV;
}
@@ -579,12 +578,11 @@ hpt372n:
pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
}
if (adjust == 8) {
- printk(KERN_ERR "pata_hpt3x2n: DPLL did not stabilize!\n");
+ pr_err(DRV_NAME ": DPLL did not stabilize!\n");
return -ENODEV;
}
- printk(KERN_INFO "pata_hpt37x: bus clock %dMHz, using 66MHz DPLL.\n",
- pci_mhz);
+ pr_info(DRV_NAME ": bus clock %dMHz, using 66MHz DPLL.\n", pci_mhz);
/*
* Set our private data up. We only need a few flags
diff --git a/drivers/ata/pata_mpc52xx.c b/drivers/ata/pata_mpc52xx.c
index 8cc536e..d7d8026 100644
--- a/drivers/ata/pata_mpc52xx.c
+++ b/drivers/ata/pata_mpc52xx.c
@@ -610,7 +610,7 @@ static struct scsi_host_template mpc52xx_ata_sht = {
};
static struct ata_port_operations mpc52xx_ata_port_ops = {
- .inherits = &ata_sff_port_ops,
+ .inherits = &ata_bmdma_port_ops,
.sff_dev_select = mpc52xx_ata_dev_select,
.set_piomode = mpc52xx_ata_set_piomode,
.set_dmamode = mpc52xx_ata_set_dmamode,
^ permalink raw reply related [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2010-08-04 18:32 ` Linus Torvalds
@ 2010-08-04 18:46 ` Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2010-08-04 18:46 UTC (permalink / raw)
To: Linus Torvalds; +Cc: Andrew Morton, linux-ide, LKML
On 08/04/2010 02:32 PM, Linus Torvalds wrote:
> On Tue, Aug 3, 2010 at 6:55 PM, Jeff Garzik<jeff@garzik.org> wrote:
>>
>> Tejun Heo (4):
>> ata_generic: drop hard coded DMA force logic for CENATEK
>> ata_piix: fix locking around SIDPR access
>> libata: more PCI IDs for jmicron controllers
>> sata_fsl,mv,nv: prepare for NCQ command completion update
>
> Hmm. Aren't these the ones that you said causes "sata_mv is behaving
> weirdly"? I think I'll wait for you to do another pull request when
> that is sorted out..
"prepare for..." is patch #1 of 2. With #2, sata_mv starts behaving
strangely. #1 seems to be working here.
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2010-08-04 1:55 Jeff Garzik
@ 2010-08-04 18:32 ` Linus Torvalds
2010-08-04 18:46 ` Jeff Garzik
0 siblings, 1 reply; 95+ messages in thread
From: Linus Torvalds @ 2010-08-04 18:32 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Andrew Morton, linux-ide, LKML
On Tue, Aug 3, 2010 at 6:55 PM, Jeff Garzik <jeff@garzik.org> wrote:
>
> Tejun Heo (4):
> ata_generic: drop hard coded DMA force logic for CENATEK
> ata_piix: fix locking around SIDPR access
> libata: more PCI IDs for jmicron controllers
> sata_fsl,mv,nv: prepare for NCQ command completion update
Hmm. Aren't these the ones that you said causes "sata_mv is behaving
weirdly"? I think I'll wait for you to do another pull request when
that is sorted out..
Linus
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2010-08-04 1:55 Jeff Garzik
2010-08-04 18:32 ` Linus Torvalds
0 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2010-08-04 1:55 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/Kconfig | 18 +
drivers/ata/Makefile | 2 +
drivers/ata/ahci.c | 2 +-
drivers/ata/ahci_platform.c | 26 +-
drivers/ata/ata_generic.c | 4 -
drivers/ata/ata_piix.c | 8 +
drivers/ata/libata-core.c | 161 ++---
drivers/ata/libata-eh.c | 1 +
drivers/ata/pata_samsung_cf.c | 683 ++++++++++++++++
drivers/ata/pata_scc.c | 3 +-
drivers/ata/sata_dwc_460ex.c | 1756 +++++++++++++++++++++++++++++++++++++++++
drivers/ata/sata_fsl.c | 20 +-
drivers/ata/sata_mv.c | 47 +-
drivers/ata/sata_nv.c | 32 +-
drivers/pci/quirks.c | 6 +
include/linux/ahci_platform.h | 4 +-
include/linux/pci_ids.h | 2 +
17 files changed, 2616 insertions(+), 159 deletions(-)
create mode 100644 drivers/ata/pata_samsung_cf.c
create mode 100644 drivers/ata/sata_dwc_460ex.c
Abhilash Kesavan (1):
[libata] Add Samsung PATA controller driver, pata_samsung_cf
Anton Vorontsov (1):
ahci_platform: Remove unneeded ahci_driver.probe assignment
FUJITA Tomonori (1):
[libata] add ATA_CMD_DSM to ata_get_cmd_descript
Jassi Brar (1):
ahci_platform: Provide for vendor specific init
Justin P. Mattock (1):
[libata] ahci: Fix warning: comparison between 'enum <anonymous>' and 'enum <anonymous>'
Mark Lord (5):
libata: glob_match for ata_device_blacklist (v2)
libata: reduce blacklist size (v2)
libata: reduce blacklist size even more (v2)
libata: allow hyphenated pattern ranges
[libata] update blacklist for new hyphenated pattern ranges (v2)
Peter Huewe (1):
ata: Convert pci_table entries to PCI_VDEVICE (if PCI_ANY_ID is used)
Rupjyoti Sarmah (1):
[libata] Add 460EX on-chip SATA driver, sata_dwc_460ex
Tejun Heo (4):
ata_generic: drop hard coded DMA force logic for CENATEK
ata_piix: fix locking around SIDPR access
libata: more PCI IDs for jmicron controllers
sata_fsl,mv,nv: prepare for NCQ command completion update
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index aa85a98..8fae6af 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -187,6 +187,15 @@ config ATA_PIIX
If unsure, say N.
+config SATA_DWC
+ tristate "DesignWare Cores SATA support"
+ depends on 460EX
+ help
+ This option enables support for the on-chip SATA controller of the
+ AppliedMicro processor 460EX.
+
+ If unsure, say N.
+
config SATA_MV
tristate "Marvell SATA support"
help
@@ -796,6 +805,15 @@ config PATA_RZ1000
If unsure, say N.
+config PATA_SAMSUNG_CF
+ tristate "Samsung SoC PATA support"
+ depends on SAMSUNG_DEV_IDE
+ help
+ This option enables basic support for Samsung's S3C/S5P board
+ PATA controllers via the new ATA layer
+
+ If unsure, say N.
+
config PATA_WINBOND_VLB
tristate "Winbond W83759A VLB PATA support (Experimental)"
depends on ISA && EXPERIMENTAL
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 7ef89d7..6540632 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -7,6 +7,7 @@ obj-$(CONFIG_SATA_AHCI_PLATFORM) += ahci_platform.o libahci.o
obj-$(CONFIG_SATA_FSL) += sata_fsl.o
obj-$(CONFIG_SATA_INIC162X) += sata_inic162x.o
obj-$(CONFIG_SATA_SIL24) += sata_sil24.o
+obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o
# SFF w/ custom DMA
obj-$(CONFIG_PDC_ADMA) += pdc_adma.o
@@ -87,6 +88,7 @@ obj-$(CONFIG_PATA_OF_PLATFORM) += pata_of_platform.o
obj-$(CONFIG_PATA_QDI) += pata_qdi.o
obj-$(CONFIG_PATA_RB532) += pata_rb532_cf.o
obj-$(CONFIG_PATA_RZ1000) += pata_rz1000.o
+obj-$(CONFIG_PATA_SAMSUNG_CF) += pata_samsung_cf.o
obj-$(CONFIG_PATA_WINBOND_VLB) += pata_winbond.o
# Should be last but two libata driver
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index f252253..fe75d8b 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -1042,7 +1042,7 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
VPRINTK("ENTER\n");
- WARN_ON(ATA_MAX_QUEUE > AHCI_MAX_CMDS);
+ WARN_ON((int)ATA_MAX_QUEUE > AHCI_MAX_CMDS);
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c
index 5e11b16..4e97f33 100644
--- a/drivers/ata/ahci_platform.c
+++ b/drivers/ata/ahci_platform.c
@@ -54,19 +54,13 @@ static int __init ahci_probe(struct platform_device *pdev)
return -EINVAL;
}
- if (pdata && pdata->init) {
- rc = pdata->init(dev);
- if (rc)
- return rc;
- }
-
if (pdata && pdata->ata_port_info)
pi = *pdata->ata_port_info;
hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
if (!hpriv) {
- rc = -ENOMEM;
- goto err0;
+ dev_err(dev, "can't alloc ahci_host_priv\n");
+ return -ENOMEM;
}
hpriv->flags |= (unsigned long)pi.private_data;
@@ -74,8 +68,19 @@ static int __init ahci_probe(struct platform_device *pdev)
hpriv->mmio = devm_ioremap(dev, mem->start, resource_size(mem));
if (!hpriv->mmio) {
dev_err(dev, "can't map %pR\n", mem);
- rc = -ENOMEM;
- goto err0;
+ return -ENOMEM;
+ }
+
+ /*
+ * Some platforms might need to prepare for mmio region access,
+ * which could be done in the following init call. So, the mmio
+ * region shouldn't be accessed before init (if provided) has
+ * returned successfully.
+ */
+ if (pdata && pdata->init) {
+ rc = pdata->init(dev, hpriv->mmio);
+ if (rc)
+ return rc;
}
ahci_save_initial_config(dev, hpriv,
@@ -166,7 +171,6 @@ static int __devexit ahci_remove(struct platform_device *pdev)
}
static struct platform_driver ahci_driver = {
- .probe = ahci_probe,
.remove = __devexit_p(ahci_remove),
.driver = {
.name = "ahci",
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
index 7107a69..cc5f772 100644
--- a/drivers/ata/ata_generic.c
+++ b/drivers/ata/ata_generic.c
@@ -54,7 +54,6 @@ static int generic_set_mode(struct ata_link *link, struct ata_device **unused)
const struct pci_device_id *id = ap->host->private_data;
int dma_enabled = 0;
struct ata_device *dev;
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
if (id->driver_data & ATA_GEN_FORCE_DMA) {
dma_enabled = 0xff;
@@ -63,9 +62,6 @@ static int generic_set_mode(struct ata_link *link, struct ata_device **unused)
dma_enabled = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
}
- if (pdev->vendor == PCI_VENDOR_ID_CENATEK)
- dma_enabled = 0xFF;
-
ata_for_each_dev(dev, link, ENABLED) {
/* We don't really care */
dev->pio_mode = XFER_PIO_0;
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 7409f98..3971bc0 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -158,6 +158,7 @@ struct piix_map_db {
struct piix_host_priv {
const int *map;
u32 saved_iocfg;
+ spinlock_t sidpr_lock; /* FIXME: remove once locking in EH is fixed */
void __iomem *sidpr;
};
@@ -951,12 +952,15 @@ static int piix_sidpr_scr_read(struct ata_link *link,
unsigned int reg, u32 *val)
{
struct piix_host_priv *hpriv = link->ap->host->private_data;
+ unsigned long flags;
if (reg >= ARRAY_SIZE(piix_sidx_map))
return -EINVAL;
+ spin_lock_irqsave(&hpriv->sidpr_lock, flags);
piix_sidpr_sel(link, reg);
*val = ioread32(hpriv->sidpr + PIIX_SIDPR_DATA);
+ spin_unlock_irqrestore(&hpriv->sidpr_lock, flags);
return 0;
}
@@ -964,12 +968,15 @@ static int piix_sidpr_scr_write(struct ata_link *link,
unsigned int reg, u32 val)
{
struct piix_host_priv *hpriv = link->ap->host->private_data;
+ unsigned long flags;
if (reg >= ARRAY_SIZE(piix_sidx_map))
return -EINVAL;
+ spin_lock_irqsave(&hpriv->sidpr_lock, flags);
piix_sidpr_sel(link, reg);
iowrite32(val, hpriv->sidpr + PIIX_SIDPR_DATA);
+ spin_unlock_irqrestore(&hpriv->sidpr_lock, flags);
return 0;
}
@@ -1566,6 +1573,7 @@ static int __devinit piix_init_one(struct pci_dev *pdev,
hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
if (!hpriv)
return -ENOMEM;
+ spin_lock_init(&hpriv->sidpr_lock);
/* Save IOCFG, this will be used for cable detection, quirk
* detection and restoration on detach. This is necessary
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index ddf8e48..a0a4d69 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -4167,15 +4167,13 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
{ "WDC AC23200L", "21.10N21", ATA_HORKAGE_NODMA },
{ "Compaq CRD-8241B", NULL, ATA_HORKAGE_NODMA },
{ "CRD-8400B", NULL, ATA_HORKAGE_NODMA },
- { "CRD-8480B", NULL, ATA_HORKAGE_NODMA },
- { "CRD-8482B", NULL, ATA_HORKAGE_NODMA },
+ { "CRD-848[02]B", NULL, ATA_HORKAGE_NODMA },
{ "CRD-84", NULL, ATA_HORKAGE_NODMA },
{ "SanDisk SDP3B", NULL, ATA_HORKAGE_NODMA },
{ "SanDisk SDP3B-64", NULL, ATA_HORKAGE_NODMA },
{ "SANYO CD-ROM CRD", NULL, ATA_HORKAGE_NODMA },
{ "HITACHI CDR-8", NULL, ATA_HORKAGE_NODMA },
- { "HITACHI CDR-8335", NULL, ATA_HORKAGE_NODMA },
- { "HITACHI CDR-8435", NULL, ATA_HORKAGE_NODMA },
+ { "HITACHI CDR-8[34]35",NULL, ATA_HORKAGE_NODMA },
{ "Toshiba CD-ROM XM-6202B", NULL, ATA_HORKAGE_NODMA },
{ "TOSHIBA CD-ROM XM-1702BC", NULL, ATA_HORKAGE_NODMA },
{ "CD-532E-A", NULL, ATA_HORKAGE_NODMA },
@@ -4211,70 +4209,16 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
{ "OCZ CORE_SSD", "02.10104", ATA_HORKAGE_NONCQ },
/* Seagate NCQ + FLUSH CACHE firmware bug */
- { "ST31500341AS", "SD15", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST31500341AS", "SD16", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST31500341AS", "SD17", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST31500341AS", "SD18", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST31500341AS", "SD19", ATA_HORKAGE_NONCQ |
+ { "ST31500341AS", "SD1[5-9]", ATA_HORKAGE_NONCQ |
ATA_HORKAGE_FIRMWARE_WARN },
- { "ST31000333AS", "SD15", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST31000333AS", "SD16", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST31000333AS", "SD17", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST31000333AS", "SD18", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST31000333AS", "SD19", ATA_HORKAGE_NONCQ |
+ { "ST31000333AS", "SD1[5-9]", ATA_HORKAGE_NONCQ |
ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3640623AS", "SD15", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3640623AS", "SD16", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3640623AS", "SD17", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3640623AS", "SD18", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3640623AS", "SD19", ATA_HORKAGE_NONCQ |
+ { "ST3640[36]23AS", "SD1[5-9]", ATA_HORKAGE_NONCQ |
ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3640323AS", "SD15", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3640323AS", "SD16", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3640323AS", "SD17", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3640323AS", "SD18", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3640323AS", "SD19", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
-
- { "ST3320813AS", "SD15", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3320813AS", "SD16", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3320813AS", "SD17", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3320813AS", "SD18", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3320813AS", "SD19", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
-
- { "ST3320613AS", "SD15", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3320613AS", "SD16", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3320613AS", "SD17", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3320613AS", "SD18", ATA_HORKAGE_NONCQ |
- ATA_HORKAGE_FIRMWARE_WARN },
- { "ST3320613AS", "SD19", ATA_HORKAGE_NONCQ |
+ { "ST3320[68]13AS", "SD1[5-9]", ATA_HORKAGE_NONCQ |
ATA_HORKAGE_FIRMWARE_WARN },
/* Blacklist entries taken from Silicon Image 3124/3132
@@ -4303,12 +4247,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
/* Devices which get the IVB wrong */
{ "QUANTUM FIREBALLlct10 05", "A03.0900", ATA_HORKAGE_IVB, },
/* Maybe we should just blacklist TSSTcorp... */
- { "TSSTcorp CDDVDW SH-S202H", "SB00", ATA_HORKAGE_IVB, },
- { "TSSTcorp CDDVDW SH-S202H", "SB01", ATA_HORKAGE_IVB, },
- { "TSSTcorp CDDVDW SH-S202J", "SB00", ATA_HORKAGE_IVB, },
- { "TSSTcorp CDDVDW SH-S202J", "SB01", ATA_HORKAGE_IVB, },
- { "TSSTcorp CDDVDW SH-S202N", "SB00", ATA_HORKAGE_IVB, },
- { "TSSTcorp CDDVDW SH-S202N", "SB01", ATA_HORKAGE_IVB, },
+ { "TSSTcorp CDDVDW SH-S202[HJN]", "SB0[01]", ATA_HORKAGE_IVB, },
/* Devices that do not need bridging limits applied */
{ "MTRON MSP-SATA*", NULL, ATA_HORKAGE_BRIDGE_OK, },
@@ -4326,29 +4265,73 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
{ }
};
-static int strn_pattern_cmp(const char *patt, const char *name, int wildchar)
+/**
+ * glob_match - match a text string against a glob-style pattern
+ * @text: the string to be examined
+ * @pattern: the glob-style pattern to be matched against
+ *
+ * Either/both of text and pattern can be empty strings.
+ *
+ * Match text against a glob-style pattern, with wildcards and simple sets:
+ *
+ * ? matches any single character.
+ * * matches any run of characters.
+ * [xyz] matches a single character from the set: x, y, or z.
+ * [a-d] matches a single character from the range: a, b, c, or d.
+ * [a-d0-9] matches a single character from either range.
+ *
+ * The special characters ?, [, -, or *, can be matched using a set, eg. [*]
+ * Behaviour with malformed patterns is undefined, though generally reasonable.
+ *
+ * Example patterns: "SD1?", "SD1[0-5]", "*R0", SD*1?[012]*xx"
+ *
+ * This function uses one level of recursion per '*' in pattern.
+ * Since it calls _nothing_ else, and has _no_ explicit local variables,
+ * this will not cause stack problems for any reasonable use here.
+ *
+ * RETURNS:
+ * 0 on match, 1 otherwise.
+ */
+static int glob_match (const char *text, const char *pattern)
{
- const char *p;
- int len;
-
- /*
- * check for trailing wildcard: *\0
- */
- p = strchr(patt, wildchar);
- if (p && ((*(p + 1)) == 0))
- len = p - patt;
- else {
- len = strlen(name);
- if (!len) {
- if (!*patt)
- return 0;
- return -1;
+ do {
+ /* Match single character or a '?' wildcard */
+ if (*text == *pattern || *pattern == '?') {
+ if (!*pattern++)
+ return 0; /* End of both strings: match */
+ } else {
+ /* Match single char against a '[' bracketed ']' pattern set */
+ if (!*text || *pattern != '[')
+ break; /* Not a pattern set */
+ while (*++pattern && *pattern != ']' && *text != *pattern) {
+ if (*pattern == '-' && *(pattern - 1) != '[')
+ if (*text > *(pattern - 1) && *text < *(pattern + 1)) {
+ ++pattern;
+ break;
+ }
+ }
+ if (!*pattern || *pattern == ']')
+ return 1; /* No match */
+ while (*pattern && *pattern++ != ']');
+ }
+ } while (*++text && *pattern);
+
+ /* Match any run of chars against a '*' wildcard */
+ if (*pattern == '*') {
+ if (!*++pattern)
+ return 0; /* Match: avoid recursion at end of pattern */
+ /* Loop to handle additional pattern chars after the wildcard */
+ while (*text) {
+ if (glob_match(text, pattern) == 0)
+ return 0; /* Remainder matched */
+ ++text; /* Absorb (match) this char and try again */
}
}
-
- return strncmp(patt, name, len);
+ if (!*text && !*pattern)
+ return 0; /* End of both strings: match */
+ return 1; /* No match */
}
-
+
static unsigned long ata_dev_blacklisted(const struct ata_device *dev)
{
unsigned char model_num[ATA_ID_PROD_LEN + 1];
@@ -4359,10 +4342,10 @@ static unsigned long ata_dev_blacklisted(const struct ata_device *dev)
ata_id_c_string(dev->id, model_rev, ATA_ID_FW_REV, sizeof(model_rev));
while (ad->model_num) {
- if (!strn_pattern_cmp(ad->model_num, model_num, '*')) {
+ if (!glob_match(model_num, ad->model_num)) {
if (ad->model_rev == NULL)
return ad->horkage;
- if (!strn_pattern_cmp(ad->model_rev, model_rev, '*'))
+ if (!glob_match(model_rev, ad->model_rev))
return ad->horkage;
}
ad++;
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index f77a673..697474b 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -2214,6 +2214,7 @@ const char *ata_get_cmd_descript(u8 command)
{ ATA_CMD_SMART, "SMART" },
{ ATA_CMD_MEDIA_LOCK, "DOOR LOCK" },
{ ATA_CMD_MEDIA_UNLOCK, "DOOR UNLOCK" },
+ { ATA_CMD_DSM, "DATA SET MANAGEMENT" },
{ ATA_CMD_CHK_MED_CRD_TYP, "CHECK MEDIA CARD TYPE" },
{ ATA_CMD_CFA_REQ_EXT_ERR, "CFA REQUEST EXTENDED ERROR" },
{ ATA_CMD_CFA_WRITE_NE, "CFA WRITE SECTORS WITHOUT ERASE" },
diff --git a/drivers/ata/pata_samsung_cf.c b/drivers/ata/pata_samsung_cf.c
new file mode 100644
index 0000000..6f9cfb2
--- /dev/null
+++ b/drivers/ata/pata_samsung_cf.c
@@ -0,0 +1,683 @@
+/*
+ * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * PATA driver for Samsung SoCs.
+ * Supports CF Interface in True IDE mode. Currently only PIO mode has been
+ * implemented; UDMA support has to be added.
+ *
+ * Based on:
+ * PATA driver for AT91SAM9260 Static Memory Controller
+ * PATA driver for Toshiba SCC controller
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/libata.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include <plat/ata.h>
+#include <plat/regs-ata.h>
+
+#define DRV_NAME "pata_samsung_cf"
+#define DRV_VERSION "0.1"
+
+enum s3c_cpu_type {
+ TYPE_S3C64XX,
+ TYPE_S5PC100,
+ TYPE_S5PV210,
+};
+
+/*
+ * struct s3c_ide_info - S3C PATA instance.
+ * @clk: The clock resource for this controller.
+ * @ide_addr: The area mapped for the hardware registers.
+ * @sfr_addr: The area mapped for the special function registers.
+ * @irq: The IRQ number we are using.
+ * @cpu_type: The exact type of this controller.
+ * @fifo_status_reg: The ATA_FIFO_STATUS register offset.
+ */
+struct s3c_ide_info {
+ struct clk *clk;
+ void __iomem *ide_addr;
+ void __iomem *sfr_addr;
+ unsigned int irq;
+ enum s3c_cpu_type cpu_type;
+ unsigned int fifo_status_reg;
+};
+
+static void pata_s3c_set_endian(void __iomem *s3c_ide_regbase, u8 mode)
+{
+ u32 reg = readl(s3c_ide_regbase + S3C_ATA_CFG);
+ reg = mode ? (reg & ~S3C_ATA_CFG_SWAP) : (reg | S3C_ATA_CFG_SWAP);
+ writel(reg, s3c_ide_regbase + S3C_ATA_CFG);
+}
+
+static void pata_s3c_cfg_mode(void __iomem *s3c_ide_sfrbase)
+{
+ /* Select true-ide as the internal operating mode */
+ writel(readl(s3c_ide_sfrbase + S3C_CFATA_MUX) | S3C_CFATA_MUX_TRUEIDE,
+ s3c_ide_sfrbase + S3C_CFATA_MUX);
+}
+
+static unsigned long
+pata_s3c_setup_timing(struct s3c_ide_info *info, const struct ata_timing *ata)
+{
+ int t1 = ata->setup;
+ int t2 = ata->act8b;
+ int t2i = ata->rec8b;
+ ulong piotime;
+
+ piotime = ((t2i & 0xff) << 12) | ((t2 & 0xff) << 4) | (t1 & 0xf);
+
+ return piotime;
+}
+
+static void pata_s3c_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct s3c_ide_info *info = ap->host->private_data;
+ struct ata_timing timing;
+ int cycle_time;
+ ulong ata_cfg = readl(info->ide_addr + S3C_ATA_CFG);
+ ulong piotime;
+
+ /* Enables IORDY if mode requires it */
+ if (ata_pio_need_iordy(adev))
+ ata_cfg |= S3C_ATA_CFG_IORDYEN;
+ else
+ ata_cfg &= ~S3C_ATA_CFG_IORDYEN;
+
+ cycle_time = (int)(1000000000UL / clk_get_rate(info->clk));
+
+ ata_timing_compute(adev, adev->pio_mode, &timing,
+ cycle_time * 1000, 0);
+
+ piotime = pata_s3c_setup_timing(info, &timing);
+
+ writel(ata_cfg, info->ide_addr + S3C_ATA_CFG);
+ writel(piotime, info->ide_addr + S3C_ATA_PIO_TIME);
+}
+
+/*
+ * Waits until the IDE controller is able to perform next read/write
+ * operation to the disk. Needed for 64XX series boards only.
+ */
+static int wait_for_host_ready(struct s3c_ide_info *info)
+{
+ ulong timeout;
+ void __iomem *fifo_reg = info->ide_addr + info->fifo_status_reg;
+
+ /* wait for maximum of 20 msec */
+ timeout = jiffies + msecs_to_jiffies(20);
+ while (time_before(jiffies, timeout)) {
+ if ((readl(fifo_reg) >> 28) == 0)
+ return 0;
+ }
+ return -EBUSY;
+}
+
+/*
+ * Writes to one of the task file registers.
+ */
+static void ata_outb(struct ata_host *host, u8 addr, void __iomem *reg)
+{
+ struct s3c_ide_info *info = host->private_data;
+
+ wait_for_host_ready(info);
+ writeb(addr, reg);
+}
+
+/*
+ * Reads from one of the task file registers.
+ */
+static u8 ata_inb(struct ata_host *host, void __iomem *reg)
+{
+ struct s3c_ide_info *info = host->private_data;
+ u8 temp;
+
+ wait_for_host_ready(info);
+ (void) readb(reg);
+ wait_for_host_ready(info);
+ temp = readb(info->ide_addr + S3C_ATA_PIO_RDATA);
+ return temp;
+}
+
+/*
+ * pata_s3c_tf_load - send taskfile registers to host controller
+ */
+static void pata_s3c_tf_load(struct ata_port *ap,
+ const struct ata_taskfile *tf)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
+
+ if (tf->ctl != ap->last_ctl) {
+ ata_outb(ap->host, tf->ctl, ioaddr->ctl_addr);
+ ap->last_ctl = tf->ctl;
+ ata_wait_idle(ap);
+ }
+
+ if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
+ ata_outb(ap->host, tf->hob_feature, ioaddr->feature_addr);
+ ata_outb(ap->host, tf->hob_nsect, ioaddr->nsect_addr);
+ ata_outb(ap->host, tf->hob_lbal, ioaddr->lbal_addr);
+ ata_outb(ap->host, tf->hob_lbam, ioaddr->lbam_addr);
+ ata_outb(ap->host, tf->hob_lbah, ioaddr->lbah_addr);
+ }
+
+ if (is_addr) {
+ ata_outb(ap->host, tf->feature, ioaddr->feature_addr);
+ ata_outb(ap->host, tf->nsect, ioaddr->nsect_addr);
+ ata_outb(ap->host, tf->lbal, ioaddr->lbal_addr);
+ ata_outb(ap->host, tf->lbam, ioaddr->lbam_addr);
+ ata_outb(ap->host, tf->lbah, ioaddr->lbah_addr);
+ }
+
+ if (tf->flags & ATA_TFLAG_DEVICE)
+ ata_outb(ap->host, tf->device, ioaddr->device_addr);
+
+ ata_wait_idle(ap);
+}
+
+/*
+ * pata_s3c_tf_read - input device's ATA taskfile shadow registers
+ */
+static void pata_s3c_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+
+ tf->feature = ata_inb(ap->host, ioaddr->error_addr);
+ tf->nsect = ata_inb(ap->host, ioaddr->nsect_addr);
+ tf->lbal = ata_inb(ap->host, ioaddr->lbal_addr);
+ tf->lbam = ata_inb(ap->host, ioaddr->lbam_addr);
+ tf->lbah = ata_inb(ap->host, ioaddr->lbah_addr);
+ tf->device = ata_inb(ap->host, ioaddr->device_addr);
+
+ if (tf->flags & ATA_TFLAG_LBA48) {
+ ata_outb(ap->host, tf->ctl | ATA_HOB, ioaddr->ctl_addr);
+ tf->hob_feature = ata_inb(ap->host, ioaddr->error_addr);
+ tf->hob_nsect = ata_inb(ap->host, ioaddr->nsect_addr);
+ tf->hob_lbal = ata_inb(ap->host, ioaddr->lbal_addr);
+ tf->hob_lbam = ata_inb(ap->host, ioaddr->lbam_addr);
+ tf->hob_lbah = ata_inb(ap->host, ioaddr->lbah_addr);
+ ata_outb(ap->host, tf->ctl, ioaddr->ctl_addr);
+ ap->last_ctl = tf->ctl;
+ }
+}
+
+/*
+ * pata_s3c_exec_command - issue ATA command to host controller
+ */
+static void pata_s3c_exec_command(struct ata_port *ap,
+ const struct ata_taskfile *tf)
+{
+ ata_outb(ap->host, tf->command, ap->ioaddr.command_addr);
+ ata_sff_pause(ap);
+}
+
+/*
+ * pata_s3c_check_status - Read device status register
+ */
+static u8 pata_s3c_check_status(struct ata_port *ap)
+{
+ return ata_inb(ap->host, ap->ioaddr.status_addr);
+}
+
+/*
+ * pata_s3c_check_altstatus - Read alternate device status register
+ */
+static u8 pata_s3c_check_altstatus(struct ata_port *ap)
+{
+ return ata_inb(ap->host, ap->ioaddr.altstatus_addr);
+}
+
+/*
+ * pata_s3c_data_xfer - Transfer data by PIO
+ */
+unsigned int pata_s3c_data_xfer(struct ata_device *dev, unsigned char *buf,
+ unsigned int buflen, int rw)
+{
+ struct ata_port *ap = dev->link->ap;
+ struct s3c_ide_info *info = ap->host->private_data;
+ void __iomem *data_addr = ap->ioaddr.data_addr;
+ unsigned int words = buflen >> 1, i;
+ u16 *data_ptr = (u16 *)buf;
+
+ /* Requires wait same as in ata_inb/ata_outb */
+ if (rw == READ)
+ for (i = 0; i < words; i++, data_ptr++) {
+ wait_for_host_ready(info);
+ (void) readw(data_addr);
+ wait_for_host_ready(info);
+ *data_ptr = readw(info->ide_addr
+ + S3C_ATA_PIO_RDATA);
+ }
+ else
+ for (i = 0; i < words; i++, data_ptr++) {
+ wait_for_host_ready(info);
+ writew(*data_ptr, data_addr);
+ }
+
+ if (buflen & 0x01)
+ dev_err(ap->dev, "unexpected trailing data\n");
+
+ return words << 1;
+}
+
+/*
+ * pata_s3c_dev_select - Select device on ATA bus
+ */
+static void pata_s3c_dev_select(struct ata_port *ap, unsigned int device)
+{
+ u8 tmp = ATA_DEVICE_OBS;
+
+ if (device != 0)
+ tmp |= ATA_DEV1;
+
+ ata_outb(ap->host, tmp, ap->ioaddr.device_addr);
+ ata_sff_pause(ap);
+}
+
+/*
+ * pata_s3c_devchk - PATA device presence detection
+ */
+static unsigned int pata_s3c_devchk(struct ata_port *ap,
+ unsigned int device)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ u8 nsect, lbal;
+
+ pata_s3c_dev_select(ap, device);
+
+ ata_outb(ap->host, 0x55, ioaddr->nsect_addr);
+ ata_outb(ap->host, 0xaa, ioaddr->lbal_addr);
+
+ ata_outb(ap->host, 0xaa, ioaddr->nsect_addr);
+ ata_outb(ap->host, 0x55, ioaddr->lbal_addr);
+
+ ata_outb(ap->host, 0x55, ioaddr->nsect_addr);
+ ata_outb(ap->host, 0xaa, ioaddr->lbal_addr);
+
+ nsect = ata_inb(ap->host, ioaddr->nsect_addr);
+ lbal = ata_inb(ap->host, ioaddr->lbal_addr);
+
+ if ((nsect == 0x55) && (lbal == 0xaa))
+ return 1; /* we found a device */
+
+ return 0; /* nothing found */
+}
+
+/*
+ * pata_s3c_wait_after_reset - wait for devices to become ready after reset
+ */
+static int pata_s3c_wait_after_reset(struct ata_link *link,
+ unsigned long deadline)
+{
+ int rc;
+
+ msleep(ATA_WAIT_AFTER_RESET);
+
+ /* always check readiness of the master device */
+ rc = ata_sff_wait_ready(link, deadline);
+ /* -ENODEV means the odd clown forgot the D7 pulldown resistor
+ * and TF status is 0xff, bail out on it too.
+ */
+ if (rc)
+ return rc;
+
+ return 0;
+}
+
+/*
+ * pata_s3c_bus_softreset - PATA device software reset
+ */
+static unsigned int pata_s3c_bus_softreset(struct ata_port *ap,
+ unsigned long deadline)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+
+ /* software reset. causes dev0 to be selected */
+ ata_outb(ap->host, ap->ctl, ioaddr->ctl_addr);
+ udelay(20);
+ ata_outb(ap->host, ap->ctl | ATA_SRST, ioaddr->ctl_addr);
+ udelay(20);
+ ata_outb(ap->host, ap->ctl, ioaddr->ctl_addr);
+ ap->last_ctl = ap->ctl;
+
+ return pata_s3c_wait_after_reset(&ap->link, deadline);
+}
+
+/*
+ * pata_s3c_softreset - reset host port via ATA SRST
+ */
+static int pata_s3c_softreset(struct ata_link *link, unsigned int *classes,
+ unsigned long deadline)
+{
+ struct ata_port *ap = link->ap;
+ unsigned int devmask = 0;
+ int rc;
+ u8 err;
+
+ /* determine if device 0 is present */
+ if (pata_s3c_devchk(ap, 0))
+ devmask |= (1 << 0);
+
+ /* select device 0 again */
+ pata_s3c_dev_select(ap, 0);
+
+ /* issue bus reset */
+ rc = pata_s3c_bus_softreset(ap, deadline);
+ /* if link is occupied, -ENODEV too is an error */
+ if (rc && rc != -ENODEV) {
+ ata_link_printk(link, KERN_ERR, "SRST failed (errno=%d)\n", rc);
+ return rc;
+ }
+
+ /* determine by signature whether we have ATA or ATAPI devices */
+ classes[0] = ata_sff_dev_classify(&ap->link.device[0],
+ devmask & (1 << 0), &err);
+
+ return 0;
+}
+
+/*
+ * pata_s3c_set_devctl - Write device control register
+ */
+static void pata_s3c_set_devctl(struct ata_port *ap, u8 ctl)
+{
+ ata_outb(ap->host, ctl, ap->ioaddr.ctl_addr);
+}
+
+static struct scsi_host_template pata_s3c_sht = {
+ ATA_PIO_SHT(DRV_NAME),
+};
+
+static struct ata_port_operations pata_s3c_port_ops = {
+ .inherits = &ata_sff_port_ops,
+ .sff_check_status = pata_s3c_check_status,
+ .sff_check_altstatus = pata_s3c_check_altstatus,
+ .sff_tf_load = pata_s3c_tf_load,
+ .sff_tf_read = pata_s3c_tf_read,
+ .sff_data_xfer = pata_s3c_data_xfer,
+ .sff_exec_command = pata_s3c_exec_command,
+ .sff_dev_select = pata_s3c_dev_select,
+ .sff_set_devctl = pata_s3c_set_devctl,
+ .softreset = pata_s3c_softreset,
+ .set_piomode = pata_s3c_set_piomode,
+};
+
+static struct ata_port_operations pata_s5p_port_ops = {
+ .inherits = &ata_sff_port_ops,
+ .set_piomode = pata_s3c_set_piomode,
+};
+
+static void pata_s3c_enable(void *s3c_ide_regbase, bool state)
+{
+ u32 temp = readl(s3c_ide_regbase + S3C_ATA_CTRL);
+ temp = state ? (temp | 1) : (temp & ~1);
+ writel(temp, s3c_ide_regbase + S3C_ATA_CTRL);
+}
+
+static irqreturn_t pata_s3c_irq(int irq, void *dev_instance)
+{
+ struct ata_host *host = dev_instance;
+ struct s3c_ide_info *info = host->private_data;
+ u32 reg;
+
+ reg = readl(info->ide_addr + S3C_ATA_IRQ);
+ writel(reg, info->ide_addr + S3C_ATA_IRQ);
+
+ return ata_sff_interrupt(irq, dev_instance);
+}
+
+static void pata_s3c_hwinit(struct s3c_ide_info *info,
+ struct s3c_ide_platdata *pdata)
+{
+ switch (info->cpu_type) {
+ case TYPE_S3C64XX:
+ /* Configure as big endian */
+ pata_s3c_cfg_mode(info->sfr_addr);
+ pata_s3c_set_endian(info->ide_addr, 1);
+ pata_s3c_enable(info->ide_addr, true);
+ msleep(100);
+
+ /* Remove IRQ Status */
+ writel(0x1f, info->ide_addr + S3C_ATA_IRQ);
+ writel(0x1b, info->ide_addr + S3C_ATA_IRQ_MSK);
+ break;
+
+ case TYPE_S5PC100:
+ pata_s3c_cfg_mode(info->sfr_addr);
+ /* FALLTHROUGH */
+
+ case TYPE_S5PV210:
+ /* Configure as little endian */
+ pata_s3c_set_endian(info->ide_addr, 0);
+ pata_s3c_enable(info->ide_addr, true);
+ msleep(100);
+
+ /* Remove IRQ Status */
+ writel(0x3f, info->ide_addr + S3C_ATA_IRQ);
+ writel(0x3f, info->ide_addr + S3C_ATA_IRQ_MSK);
+ break;
+
+ default:
+ BUG();
+ }
+}
+
+static int __init pata_s3c_probe(struct platform_device *pdev)
+{
+ struct s3c_ide_platdata *pdata = pdev->dev.platform_data;
+ struct device *dev = &pdev->dev;
+ struct s3c_ide_info *info;
+ struct resource *res;
+ struct ata_port *ap;
+ struct ata_host *host;
+ enum s3c_cpu_type cpu_type;
+ int ret;
+
+ cpu_type = platform_get_device_id(pdev)->driver_data;
+
+ info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
+ if (!info) {
+ dev_err(dev, "failed to allocate memory for device data\n");
+ return -ENOMEM;
+ }
+
+ info->irq = platform_get_irq(pdev, 0);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (res == NULL) {
+ dev_err(dev, "failed to get mem resource\n");
+ return -EINVAL;
+ }
+
+ if (!devm_request_mem_region(dev, res->start,
+ resource_size(res), DRV_NAME)) {
+ dev_err(dev, "error requesting register region\n");
+ return -EBUSY;
+ }
+
+ info->ide_addr = devm_ioremap(dev, res->start, resource_size(res));
+ if (!info->ide_addr) {
+ dev_err(dev, "failed to map IO base address\n");
+ return -ENOMEM;
+ }
+
+ info->clk = clk_get(&pdev->dev, "cfcon");
+ if (IS_ERR(info->clk)) {
+ dev_err(dev, "failed to get access to cf controller clock\n");
+ ret = PTR_ERR(info->clk);
+ info->clk = NULL;
+ return ret;
+ }
+
+ clk_enable(info->clk);
+
+ /* init ata host */
+ host = ata_host_alloc(dev, 1);
+ if (!host) {
+ dev_err(dev, "failed to allocate ide host\n");
+ ret = -ENOMEM;
+ goto stop_clk;
+ }
+
+ ap = host->ports[0];
+ ap->flags |= ATA_FLAG_MMIO;
+ ap->pio_mask = ATA_PIO4;
+
+ if (cpu_type == TYPE_S3C64XX) {
+ ap->ops = &pata_s3c_port_ops;
+ info->sfr_addr = info->ide_addr + 0x1800;
+ info->ide_addr += 0x1900;
+ info->fifo_status_reg = 0x94;
+ } else if (cpu_type == TYPE_S5PC100) {
+ ap->ops = &pata_s5p_port_ops;
+ info->sfr_addr = info->ide_addr + 0x1800;
+ info->ide_addr += 0x1900;
+ info->fifo_status_reg = 0x84;
+ } else {
+ ap->ops = &pata_s5p_port_ops;
+ info->fifo_status_reg = 0x84;
+ }
+
+ info->cpu_type = cpu_type;
+
+ if (info->irq <= 0) {
+ ap->flags |= ATA_FLAG_PIO_POLLING;
+ info->irq = 0;
+ ata_port_desc(ap, "no IRQ, using PIO polling\n");
+ }
+
+ ap->ioaddr.cmd_addr = info->ide_addr + S3C_ATA_CMD;
+ ap->ioaddr.data_addr = info->ide_addr + S3C_ATA_PIO_DTR;
+ ap->ioaddr.error_addr = info->ide_addr + S3C_ATA_PIO_FED;
+ ap->ioaddr.feature_addr = info->ide_addr + S3C_ATA_PIO_FED;
+ ap->ioaddr.nsect_addr = info->ide_addr + S3C_ATA_PIO_SCR;
+ ap->ioaddr.lbal_addr = info->ide_addr + S3C_ATA_PIO_LLR;
+ ap->ioaddr.lbam_addr = info->ide_addr + S3C_ATA_PIO_LMR;
+ ap->ioaddr.lbah_addr = info->ide_addr + S3C_ATA_PIO_LHR;
+ ap->ioaddr.device_addr = info->ide_addr + S3C_ATA_PIO_DVR;
+ ap->ioaddr.status_addr = info->ide_addr + S3C_ATA_PIO_CSD;
+ ap->ioaddr.command_addr = info->ide_addr + S3C_ATA_PIO_CSD;
+ ap->ioaddr.altstatus_addr = info->ide_addr + S3C_ATA_PIO_DAD;
+ ap->ioaddr.ctl_addr = info->ide_addr + S3C_ATA_PIO_DAD;
+
+ ata_port_desc(ap, "mmio cmd 0x%llx ",
+ (unsigned long long)res->start);
+
+ host->private_data = info;
+
+ if (pdata && pdata->setup_gpio)
+ pdata->setup_gpio();
+
+ /* Set endianness and enable the interface */
+ pata_s3c_hwinit(info, pdata);
+
+ platform_set_drvdata(pdev, host);
+
+ return ata_host_activate(host, info->irq,
+ info->irq ? pata_s3c_irq : NULL,
+ 0, &pata_s3c_sht);
+
+stop_clk:
+ clk_disable(info->clk);
+ clk_put(info->clk);
+ return ret;
+}
+
+static int __exit pata_s3c_remove(struct platform_device *pdev)
+{
+ struct ata_host *host = platform_get_drvdata(pdev);
+ struct s3c_ide_info *info = host->private_data;
+
+ ata_host_detach(host);
+
+ clk_disable(info->clk);
+ clk_put(info->clk);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int pata_s3c_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct ata_host *host = platform_get_drvdata(pdev);
+
+ return ata_host_suspend(host, PMSG_SUSPEND);
+}
+
+static int pata_s3c_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct ata_host *host = platform_get_drvdata(pdev);
+ struct s3c_ide_platdata *pdata = pdev->dev.platform_data;
+ struct s3c_ide_info *info = host->private_data;
+
+ pata_s3c_hwinit(info, pdata);
+ ata_host_resume(host);
+
+ return 0;
+}
+
+static const struct dev_pm_ops pata_s3c_pm_ops = {
+ .suspend = pata_s3c_suspend,
+ .resume = pata_s3c_resume,
+};
+#endif
+
+/* driver device registration */
+static struct platform_device_id pata_s3c_driver_ids[] = {
+ {
+ .name = "s3c64xx-pata",
+ .driver_data = TYPE_S3C64XX,
+ }, {
+ .name = "s5pc100-pata",
+ .driver_data = TYPE_S5PC100,
+ }, {
+ .name = "s5pv210-pata",
+ .driver_data = TYPE_S5PV210,
+ },
+ { }
+};
+
+MODULE_DEVICE_TABLE(platform, pata_s3c_driver_ids);
+
+static struct platform_driver pata_s3c_driver = {
+ .remove = __exit_p(pata_s3c_remove),
+ .id_table = pata_s3c_driver_ids,
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &pata_s3c_pm_ops,
+#endif
+ },
+};
+
+static int __init pata_s3c_init(void)
+{
+ return platform_driver_probe(&pata_s3c_driver, pata_s3c_probe);
+}
+
+static void __exit pata_s3c_exit(void)
+{
+ platform_driver_unregister(&pata_s3c_driver);
+}
+
+module_init(pata_s3c_init);
+module_exit(pata_s3c_exit);
+
+MODULE_AUTHOR("Abhilash Kesavan, <a.kesavan@samsung.com>");
+MODULE_DESCRIPTION("low-level driver for Samsung PATA controller");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
diff --git a/drivers/ata/pata_scc.c b/drivers/ata/pata_scc.c
index d9db3f8..fe36966 100644
--- a/drivers/ata/pata_scc.c
+++ b/drivers/ata/pata_scc.c
@@ -168,8 +168,7 @@ static const unsigned long JCACTSELtbl[2][7] = {
};
static const struct pci_device_id scc_pci_tbl[] = {
- {PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_SCC_ATA,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+ { PCI_VDEVICE(TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_SCC_ATA), 0},
{ } /* terminate list */
};
diff --git a/drivers/ata/sata_dwc_460ex.c b/drivers/ata/sata_dwc_460ex.c
new file mode 100644
index 0000000..ea24c1e
--- /dev/null
+++ b/drivers/ata/sata_dwc_460ex.c
@@ -0,0 +1,1756 @@
+/*
+ * drivers/ata/sata_dwc_460ex.c
+ *
+ * Synopsys DesignWare Cores (DWC) SATA host driver
+ *
+ * Author: Mark Miesfeld <mmiesfeld@amcc.com>
+ *
+ * Ported from 2.6.19.2 to 2.6.25/26 by Stefan Roese <sr@denx.de>
+ * Copyright 2008 DENX Software Engineering
+ *
+ * Based on versions provided by AMCC and Synopsys which are:
+ * Copyright 2006 Applied Micro Circuits Corporation
+ * COPYRIGHT (C) 2005 SYNOPSYS, INC. ALL RIGHTS RESERVED
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifdef CONFIG_SATA_DWC_DEBUG
+#define DEBUG
+#endif
+
+#ifdef CONFIG_SATA_DWC_VDEBUG
+#define VERBOSE_DEBUG
+#define DEBUG_NCQ
+#endif
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/libata.h>
+#include <linux/slab.h>
+#include "libata.h"
+
+#include <scsi/scsi_host.h>
+#include <scsi/scsi_cmnd.h>
+
+#define DRV_NAME "sata-dwc"
+#define DRV_VERSION "1.0"
+
+/* SATA DMA driver Globals */
+#define DMA_NUM_CHANS 1
+#define DMA_NUM_CHAN_REGS 8
+
+/* SATA DMA Register definitions */
+#define AHB_DMA_BRST_DFLT 64 /* 16 data items burst length*/
+
+struct dmareg {
+ u32 low; /* Low bits 0-31 */
+ u32 high; /* High bits 32-63 */
+};
+
+/* DMA Per Channel registers */
+struct dma_chan_regs {
+ struct dmareg sar; /* Source Address */
+ struct dmareg dar; /* Destination address */
+ struct dmareg llp; /* Linked List Pointer */
+ struct dmareg ctl; /* Control */
+ struct dmareg sstat; /* Source Status not implemented in core */
+ struct dmareg dstat; /* Destination Status not implemented in core*/
+ struct dmareg sstatar; /* Source Status Address not impl in core */
+ struct dmareg dstatar; /* Destination Status Address not implemente */
+ struct dmareg cfg; /* Config */
+ struct dmareg sgr; /* Source Gather */
+ struct dmareg dsr; /* Destination Scatter */
+};
+
+/* Generic Interrupt Registers */
+struct dma_interrupt_regs {
+ struct dmareg tfr; /* Transfer Interrupt */
+ struct dmareg block; /* Block Interrupt */
+ struct dmareg srctran; /* Source Transfer Interrupt */
+ struct dmareg dsttran; /* Dest Transfer Interrupt */
+ struct dmareg error; /* Error */
+};
+
+struct ahb_dma_regs {
+ struct dma_chan_regs chan_regs[DMA_NUM_CHAN_REGS];
+ struct dma_interrupt_regs interrupt_raw; /* Raw Interrupt */
+ struct dma_interrupt_regs interrupt_status; /* Interrupt Status */
+ struct dma_interrupt_regs interrupt_mask; /* Interrupt Mask */
+ struct dma_interrupt_regs interrupt_clear; /* Interrupt Clear */
+ struct dmareg statusInt; /* Interrupt combined*/
+ struct dmareg rq_srcreg; /* Src Trans Req */
+ struct dmareg rq_dstreg; /* Dst Trans Req */
+ struct dmareg rq_sgl_srcreg; /* Sngl Src Trans Req*/
+ struct dmareg rq_sgl_dstreg; /* Sngl Dst Trans Req*/
+ struct dmareg rq_lst_srcreg; /* Last Src Trans Req*/
+ struct dmareg rq_lst_dstreg; /* Last Dst Trans Req*/
+ struct dmareg dma_cfg; /* DMA Config */
+ struct dmareg dma_chan_en; /* DMA Channel Enable*/
+ struct dmareg dma_id; /* DMA ID */
+ struct dmareg dma_test; /* DMA Test */
+ struct dmareg res1; /* reserved */
+ struct dmareg res2; /* reserved */
+ /*
+ * DMA Comp Params
+ * Param 6 = dma_param[0], Param 5 = dma_param[1],
+ * Param 4 = dma_param[2] ...
+ */
+ struct dmareg dma_params[6];
+};
+
+/* Data structure for linked list item */
+struct lli {
+ u32 sar; /* Source Address */
+ u32 dar; /* Destination address */
+ u32 llp; /* Linked List Pointer */
+ struct dmareg ctl; /* Control */
+ struct dmareg dstat; /* Destination Status */
+};
+
+enum {
+ SATA_DWC_DMAC_LLI_SZ = (sizeof(struct lli)),
+ SATA_DWC_DMAC_LLI_NUM = 256,
+ SATA_DWC_DMAC_LLI_TBL_SZ = (SATA_DWC_DMAC_LLI_SZ * \
+ SATA_DWC_DMAC_LLI_NUM),
+ SATA_DWC_DMAC_TWIDTH_BYTES = 4,
+ SATA_DWC_DMAC_CTRL_TSIZE_MAX = (0x00000800 * \
+ SATA_DWC_DMAC_TWIDTH_BYTES),
+};
+
+/* DMA Register Operation Bits */
+enum {
+ DMA_EN = 0x00000001, /* Enable AHB DMA */
+ DMA_CTL_LLP_SRCEN = 0x10000000, /* Blk chain enable Src */
+ DMA_CTL_LLP_DSTEN = 0x08000000, /* Blk chain enable Dst */
+};
+
+#define DMA_CTL_BLK_TS(size) ((size) & 0x000000FFF) /* Blk Transfer size */
+#define DMA_CHANNEL(ch) (0x00000001 << (ch)) /* Select channel */
+ /* Enable channel */
+#define DMA_ENABLE_CHAN(ch) ((0x00000001 << (ch)) | \
+ ((0x000000001 << (ch)) << 8))
+ /* Disable channel */
+#define DMA_DISABLE_CHAN(ch) (0x00000000 | ((0x000000001 << (ch)) << 8))
+ /* Transfer Type & Flow Controller */
+#define DMA_CTL_TTFC(type) (((type) & 0x7) << 20)
+#define DMA_CTL_SMS(num) (((num) & 0x3) << 25) /* Src Master Select */
+#define DMA_CTL_DMS(num) (((num) & 0x3) << 23)/* Dst Master Select */
+ /* Src Burst Transaction Length */
+#define DMA_CTL_SRC_MSIZE(size) (((size) & 0x7) << 14)
+ /* Dst Burst Transaction Length */
+#define DMA_CTL_DST_MSIZE(size) (((size) & 0x7) << 11)
+ /* Source Transfer Width */
+#define DMA_CTL_SRC_TRWID(size) (((size) & 0x7) << 4)
+ /* Destination Transfer Width */
+#define DMA_CTL_DST_TRWID(size) (((size) & 0x7) << 1)
+
+/* Assign HW handshaking interface (x) to destination / source peripheral */
+#define DMA_CFG_HW_HS_DEST(int_num) (((int_num) & 0xF) << 11)
+#define DMA_CFG_HW_HS_SRC(int_num) (((int_num) & 0xF) << 7)
+#define DMA_LLP_LMS(addr, master) (((addr) & 0xfffffffc) | (master))
+
+/*
+ * This define is used to set block chaining disabled in the control low
+ * register. It is already in little endian format so it can be &'d dirctly.
+ * It is essentially: cpu_to_le32(~(DMA_CTL_LLP_SRCEN | DMA_CTL_LLP_DSTEN))
+ */
+enum {
+ DMA_CTL_LLP_DISABLE_LE32 = 0xffffffe7,
+ DMA_CTL_TTFC_P2M_DMAC = 0x00000002, /* Per to mem, DMAC cntr */
+ DMA_CTL_TTFC_M2P_PER = 0x00000003, /* Mem to per, peripheral cntr */
+ DMA_CTL_SINC_INC = 0x00000000, /* Source Address Increment */
+ DMA_CTL_SINC_DEC = 0x00000200,
+ DMA_CTL_SINC_NOCHANGE = 0x00000400,
+ DMA_CTL_DINC_INC = 0x00000000, /* Destination Address Increment */
+ DMA_CTL_DINC_DEC = 0x00000080,
+ DMA_CTL_DINC_NOCHANGE = 0x00000100,
+ DMA_CTL_INT_EN = 0x00000001, /* Interrupt Enable */
+
+/* Channel Configuration Register high bits */
+ DMA_CFG_FCMOD_REQ = 0x00000001, /* Flow Control - request based */
+ DMA_CFG_PROTCTL = (0x00000003 << 2),/* Protection Control */
+
+/* Channel Configuration Register low bits */
+ DMA_CFG_RELD_DST = 0x80000000, /* Reload Dest / Src Addr */
+ DMA_CFG_RELD_SRC = 0x40000000,
+ DMA_CFG_HS_SELSRC = 0x00000800, /* Software handshake Src/ Dest */
+ DMA_CFG_HS_SELDST = 0x00000400,
+ DMA_CFG_FIFOEMPTY = (0x00000001 << 9), /* FIFO Empty bit */
+
+/* Channel Linked List Pointer Register */
+ DMA_LLP_AHBMASTER1 = 0, /* List Master Select */
+ DMA_LLP_AHBMASTER2 = 1,
+
+ SATA_DWC_MAX_PORTS = 1,
+
+ SATA_DWC_SCR_OFFSET = 0x24,
+ SATA_DWC_REG_OFFSET = 0x64,
+};
+
+/* DWC SATA Registers */
+struct sata_dwc_regs {
+ u32 fptagr; /* 1st party DMA tag */
+ u32 fpbor; /* 1st party DMA buffer offset */
+ u32 fptcr; /* 1st party DMA Xfr count */
+ u32 dmacr; /* DMA Control */
+ u32 dbtsr; /* DMA Burst Transac size */
+ u32 intpr; /* Interrupt Pending */
+ u32 intmr; /* Interrupt Mask */
+ u32 errmr; /* Error Mask */
+ u32 llcr; /* Link Layer Control */
+ u32 phycr; /* PHY Control */
+ u32 physr; /* PHY Status */
+ u32 rxbistpd; /* Recvd BIST pattern def register */
+ u32 rxbistpd1; /* Recvd BIST data dword1 */
+ u32 rxbistpd2; /* Recvd BIST pattern data dword2 */
+ u32 txbistpd; /* Trans BIST pattern def register */
+ u32 txbistpd1; /* Trans BIST data dword1 */
+ u32 txbistpd2; /* Trans BIST data dword2 */
+ u32 bistcr; /* BIST Control Register */
+ u32 bistfctr; /* BIST FIS Count Register */
+ u32 bistsr; /* BIST Status Register */
+ u32 bistdecr; /* BIST Dword Error count register */
+ u32 res[15]; /* Reserved locations */
+ u32 testr; /* Test Register */
+ u32 versionr; /* Version Register */
+ u32 idr; /* ID Register */
+ u32 unimpl[192]; /* Unimplemented */
+ u32 dmadr[256]; /* FIFO Locations in DMA Mode */
+};
+
+enum {
+ SCR_SCONTROL_DET_ENABLE = 0x00000001,
+ SCR_SSTATUS_DET_PRESENT = 0x00000001,
+ SCR_SERROR_DIAG_X = 0x04000000,
+/* DWC SATA Register Operations */
+ SATA_DWC_TXFIFO_DEPTH = 0x01FF,
+ SATA_DWC_RXFIFO_DEPTH = 0x01FF,
+ SATA_DWC_DMACR_TMOD_TXCHEN = 0x00000004,
+ SATA_DWC_DMACR_TXCHEN = (0x00000001 | SATA_DWC_DMACR_TMOD_TXCHEN),
+ SATA_DWC_DMACR_RXCHEN = (0x00000002 | SATA_DWC_DMACR_TMOD_TXCHEN),
+ SATA_DWC_DMACR_TXRXCH_CLEAR = SATA_DWC_DMACR_TMOD_TXCHEN,
+ SATA_DWC_INTPR_DMAT = 0x00000001,
+ SATA_DWC_INTPR_NEWFP = 0x00000002,
+ SATA_DWC_INTPR_PMABRT = 0x00000004,
+ SATA_DWC_INTPR_ERR = 0x00000008,
+ SATA_DWC_INTPR_NEWBIST = 0x00000010,
+ SATA_DWC_INTPR_IPF = 0x10000000,
+ SATA_DWC_INTMR_DMATM = 0x00000001,
+ SATA_DWC_INTMR_NEWFPM = 0x00000002,
+ SATA_DWC_INTMR_PMABRTM = 0x00000004,
+ SATA_DWC_INTMR_ERRM = 0x00000008,
+ SATA_DWC_INTMR_NEWBISTM = 0x00000010,
+ SATA_DWC_LLCR_SCRAMEN = 0x00000001,
+ SATA_DWC_LLCR_DESCRAMEN = 0x00000002,
+ SATA_DWC_LLCR_RPDEN = 0x00000004,
+/* This is all error bits, zero's are reserved fields. */
+ SATA_DWC_SERROR_ERR_BITS = 0x0FFF0F03
+};
+
+#define SATA_DWC_SCR0_SPD_GET(v) (((v) >> 4) & 0x0000000F)
+#define SATA_DWC_DMACR_TX_CLEAR(v) (((v) & ~SATA_DWC_DMACR_TXCHEN) |\
+ SATA_DWC_DMACR_TMOD_TXCHEN)
+#define SATA_DWC_DMACR_RX_CLEAR(v) (((v) & ~SATA_DWC_DMACR_RXCHEN) |\
+ SATA_DWC_DMACR_TMOD_TXCHEN)
+#define SATA_DWC_DBTSR_MWR(size) (((size)/4) & SATA_DWC_TXFIFO_DEPTH)
+#define SATA_DWC_DBTSR_MRD(size) ((((size)/4) & SATA_DWC_RXFIFO_DEPTH)\
+ << 16)
+struct sata_dwc_device {
+ struct device *dev; /* generic device struct */
+ struct ata_probe_ent *pe; /* ptr to probe-ent */
+ struct ata_host *host;
+ u8 *reg_base;
+ struct sata_dwc_regs *sata_dwc_regs; /* DW Synopsys SATA specific */
+ int irq_dma;
+};
+
+#define SATA_DWC_QCMD_MAX 32
+
+struct sata_dwc_device_port {
+ struct sata_dwc_device *hsdev;
+ int cmd_issued[SATA_DWC_QCMD_MAX];
+ struct lli *llit[SATA_DWC_QCMD_MAX]; /* DMA LLI table */
+ dma_addr_t llit_dma[SATA_DWC_QCMD_MAX];
+ u32 dma_chan[SATA_DWC_QCMD_MAX];
+ int dma_pending[SATA_DWC_QCMD_MAX];
+};
+
+/*
+ * Commonly used DWC SATA driver Macros
+ */
+#define HSDEV_FROM_HOST(host) ((struct sata_dwc_device *)\
+ (host)->private_data)
+#define HSDEV_FROM_AP(ap) ((struct sata_dwc_device *)\
+ (ap)->host->private_data)
+#define HSDEVP_FROM_AP(ap) ((struct sata_dwc_device_port *)\
+ (ap)->private_data)
+#define HSDEV_FROM_QC(qc) ((struct sata_dwc_device *)\
+ (qc)->ap->host->private_data)
+#define HSDEV_FROM_HSDEVP(p) ((struct sata_dwc_device *)\
+ (hsdevp)->hsdev)
+
+enum {
+ SATA_DWC_CMD_ISSUED_NOT = 0,
+ SATA_DWC_CMD_ISSUED_PEND = 1,
+ SATA_DWC_CMD_ISSUED_EXEC = 2,
+ SATA_DWC_CMD_ISSUED_NODATA = 3,
+
+ SATA_DWC_DMA_PENDING_NONE = 0,
+ SATA_DWC_DMA_PENDING_TX = 1,
+ SATA_DWC_DMA_PENDING_RX = 2,
+};
+
+struct sata_dwc_host_priv {
+ void __iomem *scr_addr_sstatus;
+ u32 sata_dwc_sactive_issued ;
+ u32 sata_dwc_sactive_queued ;
+ u32 dma_interrupt_count;
+ struct ahb_dma_regs *sata_dma_regs;
+ struct device *dwc_dev;
+};
+struct sata_dwc_host_priv host_pvt;
+/*
+ * Prototypes
+ */
+static void sata_dwc_bmdma_start_by_tag(struct ata_queued_cmd *qc, u8 tag);
+static int sata_dwc_qc_complete(struct ata_port *ap, struct ata_queued_cmd *qc,
+ u32 check_status);
+static void sata_dwc_dma_xfer_complete(struct ata_port *ap, u32 check_status);
+static void sata_dwc_port_stop(struct ata_port *ap);
+static void sata_dwc_clear_dmacr(struct sata_dwc_device_port *hsdevp, u8 tag);
+static int dma_dwc_init(struct sata_dwc_device *hsdev, int irq);
+static void dma_dwc_exit(struct sata_dwc_device *hsdev);
+static int dma_dwc_xfer_setup(struct scatterlist *sg, int num_elems,
+ struct lli *lli, dma_addr_t dma_lli,
+ void __iomem *addr, int dir);
+static void dma_dwc_xfer_start(int dma_ch);
+
+static void sata_dwc_tf_dump(struct ata_taskfile *tf)
+{
+ dev_vdbg(host_pvt.dwc_dev, "taskfile cmd: 0x%02x protocol: %s flags:"
+ "0x%lx device: %x\n", tf->command, ata_get_cmd_descript\
+ (tf->protocol), tf->flags, tf->device);
+ dev_vdbg(host_pvt.dwc_dev, "feature: 0x%02x nsect: 0x%x lbal: 0x%x "
+ "lbam: 0x%x lbah: 0x%x\n", tf->feature, tf->nsect, tf->lbal,
+ tf->lbam, tf->lbah);
+ dev_vdbg(host_pvt.dwc_dev, "hob_feature: 0x%02x hob_nsect: 0x%x "
+ "hob_lbal: 0x%x hob_lbam: 0x%x hob_lbah: 0x%x\n",
+ tf->hob_feature, tf->hob_nsect, tf->hob_lbal, tf->hob_lbam,
+ tf->hob_lbah);
+}
+
+/*
+ * Function: get_burst_length_encode
+ * arguments: datalength: length in bytes of data
+ * returns value to be programmed in register corrresponding to data length
+ * This value is effectively the log(base 2) of the length
+ */
+static int get_burst_length_encode(int datalength)
+{
+ int items = datalength >> 2; /* div by 4 to get lword count */
+
+ if (items >= 64)
+ return 5;
+
+ if (items >= 32)
+ return 4;
+
+ if (items >= 16)
+ return 3;
+
+ if (items >= 8)
+ return 2;
+
+ if (items >= 4)
+ return 1;
+
+ return 0;
+}
+
+static void clear_chan_interrupts(int c)
+{
+ out_le32(&(host_pvt.sata_dma_regs->interrupt_clear.tfr.low),
+ DMA_CHANNEL(c));
+ out_le32(&(host_pvt.sata_dma_regs->interrupt_clear.block.low),
+ DMA_CHANNEL(c));
+ out_le32(&(host_pvt.sata_dma_regs->interrupt_clear.srctran.low),
+ DMA_CHANNEL(c));
+ out_le32(&(host_pvt.sata_dma_regs->interrupt_clear.dsttran.low),
+ DMA_CHANNEL(c));
+ out_le32(&(host_pvt.sata_dma_regs->interrupt_clear.error.low),
+ DMA_CHANNEL(c));
+}
+
+/*
+ * Function: dma_request_channel
+ * arguments: None
+ * returns channel number if available else -1
+ * This function assigns the next available DMA channel from the list to the
+ * requester
+ */
+static int dma_request_channel(void)
+{
+ int i;
+
+ for (i = 0; i < DMA_NUM_CHANS; i++) {
+ if (!(in_le32(&(host_pvt.sata_dma_regs->dma_chan_en.low)) &\
+ DMA_CHANNEL(i)))
+ return i;
+ }
+ dev_err(host_pvt.dwc_dev, "%s NO channel chan_en: 0x%08x\n", __func__,
+ in_le32(&(host_pvt.sata_dma_regs->dma_chan_en.low)));
+ return -1;
+}
+
+/*
+ * Function: dma_dwc_interrupt
+ * arguments: irq, dev_id, pt_regs
+ * returns channel number if available else -1
+ * Interrupt Handler for DW AHB SATA DMA
+ */
+static irqreturn_t dma_dwc_interrupt(int irq, void *hsdev_instance)
+{
+ int chan;
+ u32 tfr_reg, err_reg;
+ unsigned long flags;
+ struct sata_dwc_device *hsdev =
+ (struct sata_dwc_device *)hsdev_instance;
+ struct ata_host *host = (struct ata_host *)hsdev->host;
+ struct ata_port *ap;
+ struct sata_dwc_device_port *hsdevp;
+ u8 tag = 0;
+ unsigned int port = 0;
+
+ spin_lock_irqsave(&host->lock, flags);
+ ap = host->ports[port];
+ hsdevp = HSDEVP_FROM_AP(ap);
+ tag = ap->link.active_tag;
+
+ tfr_reg = in_le32(&(host_pvt.sata_dma_regs->interrupt_status.tfr\
+ .low));
+ err_reg = in_le32(&(host_pvt.sata_dma_regs->interrupt_status.error\
+ .low));
+
+ dev_dbg(ap->dev, "eot=0x%08x err=0x%08x pending=%d active port=%d\n",
+ tfr_reg, err_reg, hsdevp->dma_pending[tag], port);
+
+ for (chan = 0; chan < DMA_NUM_CHANS; chan++) {
+ /* Check for end-of-transfer interrupt. */
+ if (tfr_reg & DMA_CHANNEL(chan)) {
+ /*
+ * Each DMA command produces 2 interrupts. Only
+ * complete the command after both interrupts have been
+ * seen. (See sata_dwc_isr())
+ */
+ host_pvt.dma_interrupt_count++;
+ sata_dwc_clear_dmacr(hsdevp, tag);
+
+ if (hsdevp->dma_pending[tag] ==
+ SATA_DWC_DMA_PENDING_NONE) {
+ dev_err(ap->dev, "DMA not pending eot=0x%08x "
+ "err=0x%08x tag=0x%02x pending=%d\n",
+ tfr_reg, err_reg, tag,
+ hsdevp->dma_pending[tag]);
+ }
+
+ if ((host_pvt.dma_interrupt_count % 2) == 0)
+ sata_dwc_dma_xfer_complete(ap, 1);
+
+ /* Clear the interrupt */
+ out_le32(&(host_pvt.sata_dma_regs->interrupt_clear\
+ .tfr.low),
+ DMA_CHANNEL(chan));
+ }
+
+ /* Check for error interrupt. */
+ if (err_reg & DMA_CHANNEL(chan)) {
+ /* TODO Need error handler ! */
+ dev_err(ap->dev, "error interrupt err_reg=0x%08x\n",
+ err_reg);
+
+ /* Clear the interrupt. */
+ out_le32(&(host_pvt.sata_dma_regs->interrupt_clear\
+ .error.low),
+ DMA_CHANNEL(chan));
+ }
+ }
+ spin_unlock_irqrestore(&host->lock, flags);
+ return IRQ_HANDLED;
+}
+
+/*
+ * Function: dma_request_interrupts
+ * arguments: hsdev
+ * returns status
+ * This function registers ISR for a particular DMA channel interrupt
+ */
+static int dma_request_interrupts(struct sata_dwc_device *hsdev, int irq)
+{
+ int retval = 0;
+ int chan;
+
+ for (chan = 0; chan < DMA_NUM_CHANS; chan++) {
+ /* Unmask error interrupt */
+ out_le32(&(host_pvt.sata_dma_regs)->interrupt_mask.error.low,
+ DMA_ENABLE_CHAN(chan));
+
+ /* Unmask end-of-transfer interrupt */
+ out_le32(&(host_pvt.sata_dma_regs)->interrupt_mask.tfr.low,
+ DMA_ENABLE_CHAN(chan));
+ }
+
+ retval = request_irq(irq, dma_dwc_interrupt, 0, "SATA DMA", hsdev);
+ if (retval) {
+ dev_err(host_pvt.dwc_dev, "%s: could not get IRQ %d\n",
+ __func__, irq);
+ return -ENODEV;
+ }
+
+ /* Mark this interrupt as requested */
+ hsdev->irq_dma = irq;
+ return 0;
+}
+
+/*
+ * Function: map_sg_to_lli
+ * The Synopsis driver has a comment proposing that better performance
+ * is possible by only enabling interrupts on the last item in the linked list.
+ * However, it seems that could be a problem if an error happened on one of the
+ * first items. The transfer would halt, but no error interrupt would occur.
+ * Currently this function sets interrupts enabled for each linked list item:
+ * DMA_CTL_INT_EN.
+ */
+static int map_sg_to_lli(struct scatterlist *sg, int num_elems,
+ struct lli *lli, dma_addr_t dma_lli,
+ void __iomem *dmadr_addr, int dir)
+{
+ int i, idx = 0;
+ int fis_len = 0;
+ dma_addr_t next_llp;
+ int bl;
+
+ dev_dbg(host_pvt.dwc_dev, "%s: sg=%p nelem=%d lli=%p dma_lli=0x%08x"
+ " dmadr=0x%08x\n", __func__, sg, num_elems, lli, (u32)dma_lli,
+ (u32)dmadr_addr);
+
+ bl = get_burst_length_encode(AHB_DMA_BRST_DFLT);
+
+ for (i = 0; i < num_elems; i++, sg++) {
+ u32 addr, offset;
+ u32 sg_len, len;
+
+ addr = (u32) sg_dma_address(sg);
+ sg_len = sg_dma_len(sg);
+
+ dev_dbg(host_pvt.dwc_dev, "%s: elem=%d sg_addr=0x%x sg_len"
+ "=%d\n", __func__, i, addr, sg_len);
+
+ while (sg_len) {
+ if (idx >= SATA_DWC_DMAC_LLI_NUM) {
+ /* The LLI table is not large enough. */
+ dev_err(host_pvt.dwc_dev, "LLI table overrun "
+ "(idx=%d)\n", idx);
+ break;
+ }
+ len = (sg_len > SATA_DWC_DMAC_CTRL_TSIZE_MAX) ?
+ SATA_DWC_DMAC_CTRL_TSIZE_MAX : sg_len;
+
+ offset = addr & 0xffff;
+ if ((offset + sg_len) > 0x10000)
+ len = 0x10000 - offset;
+
+ /*
+ * Make sure a LLI block is not created that will span
+ * 8K max FIS boundary. If the block spans such a FIS
+ * boundary, there is a chance that a DMA burst will
+ * cross that boundary -- this results in an error in
+ * the host controller.
+ */
+ if (fis_len + len > 8192) {
+ dev_dbg(host_pvt.dwc_dev, "SPLITTING: fis_len="
+ "%d(0x%x) len=%d(0x%x)\n", fis_len,
+ fis_len, len, len);
+ len = 8192 - fis_len;
+ fis_len = 0;
+ } else {
+ fis_len += len;
+ }
+ if (fis_len == 8192)
+ fis_len = 0;
+
+ /*
+ * Set DMA addresses and lower half of control register
+ * based on direction.
+ */
+ if (dir == DMA_FROM_DEVICE) {
+ lli[idx].dar = cpu_to_le32(addr);
+ lli[idx].sar = cpu_to_le32((u32)dmadr_addr);
+
+ lli[idx].ctl.low = cpu_to_le32(
+ DMA_CTL_TTFC(DMA_CTL_TTFC_P2M_DMAC) |
+ DMA_CTL_SMS(0) |
+ DMA_CTL_DMS(1) |
+ DMA_CTL_SRC_MSIZE(bl) |
+ DMA_CTL_DST_MSIZE(bl) |
+ DMA_CTL_SINC_NOCHANGE |
+ DMA_CTL_SRC_TRWID(2) |
+ DMA_CTL_DST_TRWID(2) |
+ DMA_CTL_INT_EN |
+ DMA_CTL_LLP_SRCEN |
+ DMA_CTL_LLP_DSTEN);
+ } else { /* DMA_TO_DEVICE */
+ lli[idx].sar = cpu_to_le32(addr);
+ lli[idx].dar = cpu_to_le32((u32)dmadr_addr);
+
+ lli[idx].ctl.low = cpu_to_le32(
+ DMA_CTL_TTFC(DMA_CTL_TTFC_M2P_PER) |
+ DMA_CTL_SMS(1) |
+ DMA_CTL_DMS(0) |
+ DMA_CTL_SRC_MSIZE(bl) |
+ DMA_CTL_DST_MSIZE(bl) |
+ DMA_CTL_DINC_NOCHANGE |
+ DMA_CTL_SRC_TRWID(2) |
+ DMA_CTL_DST_TRWID(2) |
+ DMA_CTL_INT_EN |
+ DMA_CTL_LLP_SRCEN |
+ DMA_CTL_LLP_DSTEN);
+ }
+
+ dev_dbg(host_pvt.dwc_dev, "%s setting ctl.high len: "
+ "0x%08x val: 0x%08x\n", __func__,
+ len, DMA_CTL_BLK_TS(len / 4));
+
+ /* Program the LLI CTL high register */
+ lli[idx].ctl.high = cpu_to_le32(DMA_CTL_BLK_TS\
+ (len / 4));
+
+ /* Program the next pointer. The next pointer must be
+ * the physical address, not the virtual address.
+ */
+ next_llp = (dma_lli + ((idx + 1) * sizeof(struct \
+ lli)));
+
+ /* The last 2 bits encode the list master select. */
+ next_llp = DMA_LLP_LMS(next_llp, DMA_LLP_AHBMASTER2);
+
+ lli[idx].llp = cpu_to_le32(next_llp);
+ idx++;
+ sg_len -= len;
+ addr += len;
+ }
+ }
+
+ /*
+ * The last next ptr has to be zero and the last control low register
+ * has to have LLP_SRC_EN and LLP_DST_EN (linked list pointer source
+ * and destination enable) set back to 0 (disabled.) This is what tells
+ * the core that this is the last item in the linked list.
+ */
+ if (idx) {
+ lli[idx-1].llp = 0x00000000;
+ lli[idx-1].ctl.low &= DMA_CTL_LLP_DISABLE_LE32;
+
+ /* Flush cache to memory */
+ dma_cache_sync(NULL, lli, (sizeof(struct lli) * idx),
+ DMA_BIDIRECTIONAL);
+ }
+
+ return idx;
+}
+
+/*
+ * Function: dma_dwc_xfer_start
+ * arguments: Channel number
+ * Return : None
+ * Enables the DMA channel
+ */
+static void dma_dwc_xfer_start(int dma_ch)
+{
+ /* Enable the DMA channel */
+ out_le32(&(host_pvt.sata_dma_regs->dma_chan_en.low),
+ in_le32(&(host_pvt.sata_dma_regs->dma_chan_en.low)) |
+ DMA_ENABLE_CHAN(dma_ch));
+}
+
+static int dma_dwc_xfer_setup(struct scatterlist *sg, int num_elems,
+ struct lli *lli, dma_addr_t dma_lli,
+ void __iomem *addr, int dir)
+{
+ int dma_ch;
+ int num_lli;
+ /* Acquire DMA channel */
+ dma_ch = dma_request_channel();
+ if (dma_ch == -1) {
+ dev_err(host_pvt.dwc_dev, "%s: dma channel unavailable\n",
+ __func__);
+ return -EAGAIN;
+ }
+
+ /* Convert SG list to linked list of items (LLIs) for AHB DMA */
+ num_lli = map_sg_to_lli(sg, num_elems, lli, dma_lli, addr, dir);
+
+ dev_dbg(host_pvt.dwc_dev, "%s sg: 0x%p, count: %d lli: %p dma_lli:"
+ " 0x%0xlx addr: %p lli count: %d\n", __func__, sg, num_elems,
+ lli, (u32)dma_lli, addr, num_lli);
+
+ clear_chan_interrupts(dma_ch);
+
+ /* Program the CFG register. */
+ out_le32(&(host_pvt.sata_dma_regs->chan_regs[dma_ch].cfg.high),
+ DMA_CFG_PROTCTL | DMA_CFG_FCMOD_REQ);
+ out_le32(&(host_pvt.sata_dma_regs->chan_regs[dma_ch].cfg.low), 0);
+
+ /* Program the address of the linked list */
+ out_le32(&(host_pvt.sata_dma_regs->chan_regs[dma_ch].llp.low),
+ DMA_LLP_LMS(dma_lli, DMA_LLP_AHBMASTER2));
+
+ /* Program the CTL register with src enable / dst enable */
+ out_le32(&(host_pvt.sata_dma_regs->chan_regs[dma_ch].ctl.low),
+ DMA_CTL_LLP_SRCEN | DMA_CTL_LLP_DSTEN);
+ return 0;
+}
+
+/*
+ * Function: dma_dwc_exit
+ * arguments: None
+ * returns status
+ * This function exits the SATA DMA driver
+ */
+static void dma_dwc_exit(struct sata_dwc_device *hsdev)
+{
+ dev_dbg(host_pvt.dwc_dev, "%s:\n", __func__);
+ if (host_pvt.sata_dma_regs)
+ iounmap(host_pvt.sata_dma_regs);
+
+ if (hsdev->irq_dma)
+ free_irq(hsdev->irq_dma, hsdev);
+}
+
+/*
+ * Function: dma_dwc_init
+ * arguments: hsdev
+ * returns status
+ * This function initializes the SATA DMA driver
+ */
+static int dma_dwc_init(struct sata_dwc_device *hsdev, int irq)
+{
+ int err;
+
+ err = dma_request_interrupts(hsdev, irq);
+ if (err) {
+ dev_err(host_pvt.dwc_dev, "%s: dma_request_interrupts returns"
+ " %d\n", __func__, err);
+ goto error_out;
+ }
+
+ /* Enabe DMA */
+ out_le32(&(host_pvt.sata_dma_regs->dma_cfg.low), DMA_EN);
+
+ dev_notice(host_pvt.dwc_dev, "DMA initialized\n");
+ dev_dbg(host_pvt.dwc_dev, "SATA DMA registers=0x%p\n", host_pvt.\
+ sata_dma_regs);
+
+ return 0;
+
+error_out:
+ dma_dwc_exit(hsdev);
+
+ return err;
+}
+
+static int sata_dwc_scr_read(struct ata_link *link, unsigned int scr, u32 *val)
+{
+ if (scr > SCR_NOTIFICATION) {
+ dev_err(link->ap->dev, "%s: Incorrect SCR offset 0x%02x\n",
+ __func__, scr);
+ return -EINVAL;
+ }
+
+ *val = in_le32((void *)link->ap->ioaddr.scr_addr + (scr * 4));
+ dev_dbg(link->ap->dev, "%s: id=%d reg=%d val=val=0x%08x\n",
+ __func__, link->ap->print_id, scr, *val);
+
+ return 0;
+}
+
+static int sata_dwc_scr_write(struct ata_link *link, unsigned int scr, u32 val)
+{
+ dev_dbg(link->ap->dev, "%s: id=%d reg=%d val=val=0x%08x\n",
+ __func__, link->ap->print_id, scr, val);
+ if (scr > SCR_NOTIFICATION) {
+ dev_err(link->ap->dev, "%s: Incorrect SCR offset 0x%02x\n",
+ __func__, scr);
+ return -EINVAL;
+ }
+ out_le32((void *)link->ap->ioaddr.scr_addr + (scr * 4), val);
+
+ return 0;
+}
+
+static u32 core_scr_read(unsigned int scr)
+{
+ return in_le32((void __iomem *)(host_pvt.scr_addr_sstatus) +\
+ (scr * 4));
+}
+
+static void core_scr_write(unsigned int scr, u32 val)
+{
+ out_le32((void __iomem *)(host_pvt.scr_addr_sstatus) + (scr * 4),
+ val);
+}
+
+static void clear_serror(void)
+{
+ u32 val;
+ val = core_scr_read(SCR_ERROR);
+ core_scr_write(SCR_ERROR, val);
+
+}
+
+static void clear_interrupt_bit(struct sata_dwc_device *hsdev, u32 bit)
+{
+ out_le32(&hsdev->sata_dwc_regs->intpr,
+ in_le32(&hsdev->sata_dwc_regs->intpr));
+}
+
+static u32 qcmd_tag_to_mask(u8 tag)
+{
+ return 0x00000001 << (tag & 0x1f);
+}
+
+/* See ahci.c */
+static void sata_dwc_error_intr(struct ata_port *ap,
+ struct sata_dwc_device *hsdev, uint intpr)
+{
+ struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
+ struct ata_eh_info *ehi = &ap->link.eh_info;
+ unsigned int err_mask = 0, action = 0;
+ struct ata_queued_cmd *qc;
+ u32 serror;
+ u8 status, tag;
+ u32 err_reg;
+
+ ata_ehi_clear_desc(ehi);
+
+ serror = core_scr_read(SCR_ERROR);
+ status = ap->ops->sff_check_status(ap);
+
+ err_reg = in_le32(&(host_pvt.sata_dma_regs->interrupt_status.error.\
+ low));
+ tag = ap->link.active_tag;
+
+ dev_err(ap->dev, "%s SCR_ERROR=0x%08x intpr=0x%08x status=0x%08x "
+ "dma_intp=%d pending=%d issued=%d dma_err_status=0x%08x\n",
+ __func__, serror, intpr, status, host_pvt.dma_interrupt_count,
+ hsdevp->dma_pending[tag], hsdevp->cmd_issued[tag], err_reg);
+
+ /* Clear error register and interrupt bit */
+ clear_serror();
+ clear_interrupt_bit(hsdev, SATA_DWC_INTPR_ERR);
+
+ /* This is the only error happening now. TODO check for exact error */
+
+ err_mask |= AC_ERR_HOST_BUS;
+ action |= ATA_EH_RESET;
+
+ /* Pass this on to EH */
+ ehi->serror |= serror;
+ ehi->action |= action;
+
+ qc = ata_qc_from_tag(ap, tag);
+ if (qc)
+ qc->err_mask |= err_mask;
+ else
+ ehi->err_mask |= err_mask;
+
+ ata_port_abort(ap);
+}
+
+/*
+ * Function : sata_dwc_isr
+ * arguments : irq, void *dev_instance, struct pt_regs *regs
+ * Return value : irqreturn_t - status of IRQ
+ * This Interrupt handler called via port ops registered function.
+ * .irq_handler = sata_dwc_isr
+ */
+static irqreturn_t sata_dwc_isr(int irq, void *dev_instance)
+{
+ struct ata_host *host = (struct ata_host *)dev_instance;
+ struct sata_dwc_device *hsdev = HSDEV_FROM_HOST(host);
+ struct ata_port *ap;
+ struct ata_queued_cmd *qc;
+ unsigned long flags;
+ u8 status, tag;
+ int handled, num_processed, port = 0;
+ uint intpr, sactive, sactive2, tag_mask;
+ struct sata_dwc_device_port *hsdevp;
+ host_pvt.sata_dwc_sactive_issued = 0;
+
+ spin_lock_irqsave(&host->lock, flags);
+
+ /* Read the interrupt register */
+ intpr = in_le32(&hsdev->sata_dwc_regs->intpr);
+
+ ap = host->ports[port];
+ hsdevp = HSDEVP_FROM_AP(ap);
+
+ dev_dbg(ap->dev, "%s intpr=0x%08x active_tag=%d\n", __func__, intpr,
+ ap->link.active_tag);
+
+ /* Check for error interrupt */
+ if (intpr & SATA_DWC_INTPR_ERR) {
+ sata_dwc_error_intr(ap, hsdev, intpr);
+ handled = 1;
+ goto DONE;
+ }
+
+ /* Check for DMA SETUP FIS (FP DMA) interrupt */
+ if (intpr & SATA_DWC_INTPR_NEWFP) {
+ clear_interrupt_bit(hsdev, SATA_DWC_INTPR_NEWFP);
+
+ tag = (u8)(in_le32(&hsdev->sata_dwc_regs->fptagr));
+ dev_dbg(ap->dev, "%s: NEWFP tag=%d\n", __func__, tag);
+ if (hsdevp->cmd_issued[tag] != SATA_DWC_CMD_ISSUED_PEND)
+ dev_warn(ap->dev, "CMD tag=%d not pending?\n", tag);
+
+ host_pvt.sata_dwc_sactive_issued |= qcmd_tag_to_mask(tag);
+
+ qc = ata_qc_from_tag(ap, tag);
+ /*
+ * Start FP DMA for NCQ command. At this point the tag is the
+ * active tag. It is the tag that matches the command about to
+ * be completed.
+ */
+ qc->ap->link.active_tag = tag;
+ sata_dwc_bmdma_start_by_tag(qc, tag);
+
+ handled = 1;
+ goto DONE;
+ }
+ sactive = core_scr_read(SCR_ACTIVE);
+ tag_mask = (host_pvt.sata_dwc_sactive_issued | sactive) ^ sactive;
+
+ /* If no sactive issued and tag_mask is zero then this is not NCQ */
+ if (host_pvt.sata_dwc_sactive_issued == 0 && tag_mask == 0) {
+ if (ap->link.active_tag == ATA_TAG_POISON)
+ tag = 0;
+ else
+ tag = ap->link.active_tag;
+ qc = ata_qc_from_tag(ap, tag);
+
+ /* DEV interrupt w/ no active qc? */
+ if (unlikely(!qc || (qc->tf.flags & ATA_TFLAG_POLLING))) {
+ dev_err(ap->dev, "%s interrupt with no active qc "
+ "qc=%p\n", __func__, qc);
+ ap->ops->sff_check_status(ap);
+ handled = 1;
+ goto DONE;
+ }
+ status = ap->ops->sff_check_status(ap);
+
+ qc->ap->link.active_tag = tag;
+ hsdevp->cmd_issued[tag] = SATA_DWC_CMD_ISSUED_NOT;
+
+ if (status & ATA_ERR) {
+ dev_dbg(ap->dev, "interrupt ATA_ERR (0x%x)\n", status);
+ sata_dwc_qc_complete(ap, qc, 1);
+ handled = 1;
+ goto DONE;
+ }
+
+ dev_dbg(ap->dev, "%s non-NCQ cmd interrupt, protocol: %s\n",
+ __func__, ata_get_cmd_descript(qc->tf.protocol));
+DRVSTILLBUSY:
+ if (ata_is_dma(qc->tf.protocol)) {
+ /*
+ * Each DMA transaction produces 2 interrupts. The DMAC
+ * transfer complete interrupt and the SATA controller
+ * operation done interrupt. The command should be
+ * completed only after both interrupts are seen.
+ */
+ host_pvt.dma_interrupt_count++;
+ if (hsdevp->dma_pending[tag] == \
+ SATA_DWC_DMA_PENDING_NONE) {
+ dev_err(ap->dev, "%s: DMA not pending "
+ "intpr=0x%08x status=0x%08x pending"
+ "=%d\n", __func__, intpr, status,
+ hsdevp->dma_pending[tag]);
+ }
+
+ if ((host_pvt.dma_interrupt_count % 2) == 0)
+ sata_dwc_dma_xfer_complete(ap, 1);
+ } else if (ata_is_pio(qc->tf.protocol)) {
+ ata_sff_hsm_move(ap, qc, status, 0);
+ handled = 1;
+ goto DONE;
+ } else {
+ if (unlikely(sata_dwc_qc_complete(ap, qc, 1)))
+ goto DRVSTILLBUSY;
+ }
+
+ handled = 1;
+ goto DONE;
+ }
+
+ /*
+ * This is a NCQ command. At this point we need to figure out for which
+ * tags we have gotten a completion interrupt. One interrupt may serve
+ * as completion for more than one operation when commands are queued
+ * (NCQ). We need to process each completed command.
+ */
+
+ /* process completed commands */
+ sactive = core_scr_read(SCR_ACTIVE);
+ tag_mask = (host_pvt.sata_dwc_sactive_issued | sactive) ^ sactive;
+
+ if (sactive != 0 || (host_pvt.sata_dwc_sactive_issued) > 1 || \
+ tag_mask > 1) {
+ dev_dbg(ap->dev, "%s NCQ:sactive=0x%08x sactive_issued=0x%08x"
+ "tag_mask=0x%08x\n", __func__, sactive,
+ host_pvt.sata_dwc_sactive_issued, tag_mask);
+ }
+
+ if ((tag_mask | (host_pvt.sata_dwc_sactive_issued)) != \
+ (host_pvt.sata_dwc_sactive_issued)) {
+ dev_warn(ap->dev, "Bad tag mask? sactive=0x%08x "
+ "(host_pvt.sata_dwc_sactive_issued)=0x%08x tag_mask"
+ "=0x%08x\n", sactive, host_pvt.sata_dwc_sactive_issued,
+ tag_mask);
+ }
+
+ /* read just to clear ... not bad if currently still busy */
+ status = ap->ops->sff_check_status(ap);
+ dev_dbg(ap->dev, "%s ATA status register=0x%x\n", __func__, status);
+
+ tag = 0;
+ num_processed = 0;
+ while (tag_mask) {
+ num_processed++;
+ while (!(tag_mask & 0x00000001)) {
+ tag++;
+ tag_mask <<= 1;
+ }
+
+ tag_mask &= (~0x00000001);
+ qc = ata_qc_from_tag(ap, tag);
+
+ /* To be picked up by completion functions */
+ qc->ap->link.active_tag = tag;
+ hsdevp->cmd_issued[tag] = SATA_DWC_CMD_ISSUED_NOT;
+
+ /* Let libata/scsi layers handle error */
+ if (status & ATA_ERR) {
+ dev_dbg(ap->dev, "%s ATA_ERR (0x%x)\n", __func__,
+ status);
+ sata_dwc_qc_complete(ap, qc, 1);
+ handled = 1;
+ goto DONE;
+ }
+
+ /* Process completed command */
+ dev_dbg(ap->dev, "%s NCQ command, protocol: %s\n", __func__,
+ ata_get_cmd_descript(qc->tf.protocol));
+ if (ata_is_dma(qc->tf.protocol)) {
+ host_pvt.dma_interrupt_count++;
+ if (hsdevp->dma_pending[tag] == \
+ SATA_DWC_DMA_PENDING_NONE)
+ dev_warn(ap->dev, "%s: DMA not pending?\n",
+ __func__);
+ if ((host_pvt.dma_interrupt_count % 2) == 0)
+ sata_dwc_dma_xfer_complete(ap, 1);
+ } else {
+ if (unlikely(sata_dwc_qc_complete(ap, qc, 1)))
+ goto STILLBUSY;
+ }
+ continue;
+
+STILLBUSY:
+ ap->stats.idle_irq++;
+ dev_warn(ap->dev, "STILL BUSY IRQ ata%d: irq trap\n",
+ ap->print_id);
+ } /* while tag_mask */
+
+ /*
+ * Check to see if any commands completed while we were processing our
+ * initial set of completed commands (read status clears interrupts,
+ * so we might miss a completed command interrupt if one came in while
+ * we were processing --we read status as part of processing a completed
+ * command).
+ */
+ sactive2 = core_scr_read(SCR_ACTIVE);
+ if (sactive2 != sactive) {
+ dev_dbg(ap->dev, "More completed - sactive=0x%x sactive2"
+ "=0x%x\n", sactive, sactive2);
+ }
+ handled = 1;
+
+DONE:
+ spin_unlock_irqrestore(&host->lock, flags);
+ return IRQ_RETVAL(handled);
+}
+
+static void sata_dwc_clear_dmacr(struct sata_dwc_device_port *hsdevp, u8 tag)
+{
+ struct sata_dwc_device *hsdev = HSDEV_FROM_HSDEVP(hsdevp);
+
+ if (hsdevp->dma_pending[tag] == SATA_DWC_DMA_PENDING_RX) {
+ out_le32(&(hsdev->sata_dwc_regs->dmacr),
+ SATA_DWC_DMACR_RX_CLEAR(
+ in_le32(&(hsdev->sata_dwc_regs->dmacr))));
+ } else if (hsdevp->dma_pending[tag] == SATA_DWC_DMA_PENDING_TX) {
+ out_le32(&(hsdev->sata_dwc_regs->dmacr),
+ SATA_DWC_DMACR_TX_CLEAR(
+ in_le32(&(hsdev->sata_dwc_regs->dmacr))));
+ } else {
+ /*
+ * This should not happen, it indicates the driver is out of
+ * sync. If it does happen, clear dmacr anyway.
+ */
+ dev_err(host_pvt.dwc_dev, "%s DMA protocol RX and"
+ "TX DMA not pending tag=0x%02x pending=%d"
+ " dmacr: 0x%08x\n", __func__, tag,
+ hsdevp->dma_pending[tag],
+ in_le32(&(hsdev->sata_dwc_regs->dmacr)));
+ out_le32(&(hsdev->sata_dwc_regs->dmacr),
+ SATA_DWC_DMACR_TXRXCH_CLEAR);
+ }
+}
+
+static void sata_dwc_dma_xfer_complete(struct ata_port *ap, u32 check_status)
+{
+ struct ata_queued_cmd *qc;
+ struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
+ struct sata_dwc_device *hsdev = HSDEV_FROM_AP(ap);
+ u8 tag = 0;
+
+ tag = ap->link.active_tag;
+ qc = ata_qc_from_tag(ap, tag);
+ if (!qc) {
+ dev_err(ap->dev, "failed to get qc");
+ return;
+ }
+
+#ifdef DEBUG_NCQ
+ if (tag > 0) {
+ dev_info(ap->dev, "%s tag=%u cmd=0x%02x dma dir=%s proto=%s "
+ "dmacr=0x%08x\n", __func__, qc->tag, qc->tf.command,
+ ata_get_cmd_descript(qc->dma_dir),
+ ata_get_cmd_descript(qc->tf.protocol),
+ in_le32(&(hsdev->sata_dwc_regs->dmacr)));
+ }
+#endif
+
+ if (ata_is_dma(qc->tf.protocol)) {
+ if (hsdevp->dma_pending[tag] == SATA_DWC_DMA_PENDING_NONE) {
+ dev_err(ap->dev, "%s DMA protocol RX and TX DMA not "
+ "pending dmacr: 0x%08x\n", __func__,
+ in_le32(&(hsdev->sata_dwc_regs->dmacr)));
+ }
+
+ hsdevp->dma_pending[tag] = SATA_DWC_DMA_PENDING_NONE;
+ sata_dwc_qc_complete(ap, qc, check_status);
+ ap->link.active_tag = ATA_TAG_POISON;
+ } else {
+ sata_dwc_qc_complete(ap, qc, check_status);
+ }
+}
+
+static int sata_dwc_qc_complete(struct ata_port *ap, struct ata_queued_cmd *qc,
+ u32 check_status)
+{
+ u8 status = 0;
+ u32 mask = 0x0;
+ u8 tag = qc->tag;
+ struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
+ host_pvt.sata_dwc_sactive_queued = 0;
+ dev_dbg(ap->dev, "%s checkstatus? %x\n", __func__, check_status);
+
+ if (hsdevp->dma_pending[tag] == SATA_DWC_DMA_PENDING_TX)
+ dev_err(ap->dev, "TX DMA PENDING\n");
+ else if (hsdevp->dma_pending[tag] == SATA_DWC_DMA_PENDING_RX)
+ dev_err(ap->dev, "RX DMA PENDING\n");
+ dev_dbg(ap->dev, "QC complete cmd=0x%02x status=0x%02x ata%u:"
+ " protocol=%d\n", qc->tf.command, status, ap->print_id,
+ qc->tf.protocol);
+
+ /* clear active bit */
+ mask = (~(qcmd_tag_to_mask(tag)));
+ host_pvt.sata_dwc_sactive_queued = (host_pvt.sata_dwc_sactive_queued) \
+ & mask;
+ host_pvt.sata_dwc_sactive_issued = (host_pvt.sata_dwc_sactive_issued) \
+ & mask;
+ ata_qc_complete(qc);
+ return 0;
+}
+
+static void sata_dwc_enable_interrupts(struct sata_dwc_device *hsdev)
+{
+ /* Enable selective interrupts by setting the interrupt maskregister*/
+ out_le32(&hsdev->sata_dwc_regs->intmr,
+ SATA_DWC_INTMR_ERRM |
+ SATA_DWC_INTMR_NEWFPM |
+ SATA_DWC_INTMR_PMABRTM |
+ SATA_DWC_INTMR_DMATM);
+ /*
+ * Unmask the error bits that should trigger an error interrupt by
+ * setting the error mask register.
+ */
+ out_le32(&hsdev->sata_dwc_regs->errmr, SATA_DWC_SERROR_ERR_BITS);
+
+ dev_dbg(host_pvt.dwc_dev, "%s: INTMR = 0x%08x, ERRMR = 0x%08x\n",
+ __func__, in_le32(&hsdev->sata_dwc_regs->intmr),
+ in_le32(&hsdev->sata_dwc_regs->errmr));
+}
+
+static void sata_dwc_setup_port(struct ata_ioports *port, unsigned long base)
+{
+ port->cmd_addr = (void *)base + 0x00;
+ port->data_addr = (void *)base + 0x00;
+
+ port->error_addr = (void *)base + 0x04;
+ port->feature_addr = (void *)base + 0x04;
+
+ port->nsect_addr = (void *)base + 0x08;
+
+ port->lbal_addr = (void *)base + 0x0c;
+ port->lbam_addr = (void *)base + 0x10;
+ port->lbah_addr = (void *)base + 0x14;
+
+ port->device_addr = (void *)base + 0x18;
+ port->command_addr = (void *)base + 0x1c;
+ port->status_addr = (void *)base + 0x1c;
+
+ port->altstatus_addr = (void *)base + 0x20;
+ port->ctl_addr = (void *)base + 0x20;
+}
+
+/*
+ * Function : sata_dwc_port_start
+ * arguments : struct ata_ioports *port
+ * Return value : returns 0 if success, error code otherwise
+ * This function allocates the scatter gather LLI table for AHB DMA
+ */
+static int sata_dwc_port_start(struct ata_port *ap)
+{
+ int err = 0;
+ struct sata_dwc_device *hsdev;
+ struct sata_dwc_device_port *hsdevp = NULL;
+ struct device *pdev;
+ int i;
+
+ hsdev = HSDEV_FROM_AP(ap);
+
+ dev_dbg(ap->dev, "%s: port_no=%d\n", __func__, ap->port_no);
+
+ hsdev->host = ap->host;
+ pdev = ap->host->dev;
+ if (!pdev) {
+ dev_err(ap->dev, "%s: no ap->host->dev\n", __func__);
+ err = -ENODEV;
+ goto CLEANUP;
+ }
+
+ /* Allocate Port Struct */
+ hsdevp = kzalloc(sizeof(*hsdevp), GFP_KERNEL);
+ if (!hsdevp) {
+ dev_err(ap->dev, "%s: kmalloc failed for hsdevp\n", __func__);
+ err = -ENOMEM;
+ goto CLEANUP;
+ }
+ hsdevp->hsdev = hsdev;
+
+ for (i = 0; i < SATA_DWC_QCMD_MAX; i++)
+ hsdevp->cmd_issued[i] = SATA_DWC_CMD_ISSUED_NOT;
+
+ ap->bmdma_prd = 0; /* set these so libata doesn't use them */
+ ap->bmdma_prd_dma = 0;
+
+ /*
+ * DMA - Assign scatter gather LLI table. We can't use the libata
+ * version since it's PRD is IDE PCI specific.
+ */
+ for (i = 0; i < SATA_DWC_QCMD_MAX; i++) {
+ hsdevp->llit[i] = dma_alloc_coherent(pdev,
+ SATA_DWC_DMAC_LLI_TBL_SZ,
+ &(hsdevp->llit_dma[i]),
+ GFP_ATOMIC);
+ if (!hsdevp->llit[i]) {
+ dev_err(ap->dev, "%s: dma_alloc_coherent failed\n",
+ __func__);
+ err = -ENOMEM;
+ goto CLEANUP;
+ }
+ }
+
+ if (ap->port_no == 0) {
+ dev_dbg(ap->dev, "%s: clearing TXCHEN, RXCHEN in DMAC\n",
+ __func__);
+ out_le32(&hsdev->sata_dwc_regs->dmacr,
+ SATA_DWC_DMACR_TXRXCH_CLEAR);
+
+ dev_dbg(ap->dev, "%s: setting burst size in DBTSR\n",
+ __func__);
+ out_le32(&hsdev->sata_dwc_regs->dbtsr,
+ (SATA_DWC_DBTSR_MWR(AHB_DMA_BRST_DFLT) |
+ SATA_DWC_DBTSR_MRD(AHB_DMA_BRST_DFLT)));
+ }
+
+ /* Clear any error bits before libata starts issuing commands */
+ clear_serror();
+ ap->private_data = hsdevp;
+
+CLEANUP:
+ if (err) {
+ sata_dwc_port_stop(ap);
+ dev_dbg(ap->dev, "%s: fail\n", __func__);
+ } else {
+ dev_dbg(ap->dev, "%s: done\n", __func__);
+ }
+
+ return err;
+}
+
+static void sata_dwc_port_stop(struct ata_port *ap)
+{
+ int i;
+ struct sata_dwc_device *hsdev = HSDEV_FROM_AP(ap);
+ struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
+
+ dev_dbg(ap->dev, "%s: ap->id = %d\n", __func__, ap->print_id);
+
+ if (hsdevp && hsdev) {
+ /* deallocate LLI table */
+ for (i = 0; i < SATA_DWC_QCMD_MAX; i++) {
+ dma_free_coherent(ap->host->dev,
+ SATA_DWC_DMAC_LLI_TBL_SZ,
+ hsdevp->llit[i], hsdevp->llit_dma[i]);
+ }
+
+ kfree(hsdevp);
+ }
+ ap->private_data = NULL;
+}
+
+/*
+ * Function : sata_dwc_exec_command_by_tag
+ * arguments : ata_port *ap, ata_taskfile *tf, u8 tag, u32 cmd_issued
+ * Return value : None
+ * This function keeps track of individual command tag ids and calls
+ * ata_exec_command in libata
+ */
+static void sata_dwc_exec_command_by_tag(struct ata_port *ap,
+ struct ata_taskfile *tf,
+ u8 tag, u32 cmd_issued)
+{
+ unsigned long flags;
+ struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
+
+ dev_dbg(ap->dev, "%s cmd(0x%02x): %s tag=%d\n", __func__, tf->command,
+ ata_get_cmd_descript(tf), tag);
+
+ spin_lock_irqsave(&ap->host->lock, flags);
+ hsdevp->cmd_issued[tag] = cmd_issued;
+ spin_unlock_irqrestore(&ap->host->lock, flags);
+ /*
+ * Clear SError before executing a new command.
+ * sata_dwc_scr_write and read can not be used here. Clearing the PM
+ * managed SError register for the disk needs to be done before the
+ * task file is loaded.
+ */
+ clear_serror();
+ ata_sff_exec_command(ap, tf);
+}
+
+static void sata_dwc_bmdma_setup_by_tag(struct ata_queued_cmd *qc, u8 tag)
+{
+ sata_dwc_exec_command_by_tag(qc->ap, &qc->tf, tag,
+ SATA_DWC_CMD_ISSUED_PEND);
+}
+
+static void sata_dwc_bmdma_setup(struct ata_queued_cmd *qc)
+{
+ u8 tag = qc->tag;
+
+ if (ata_is_ncq(qc->tf.protocol)) {
+ dev_dbg(qc->ap->dev, "%s: ap->link.sactive=0x%08x tag=%d\n",
+ __func__, qc->ap->link.sactive, tag);
+ } else {
+ tag = 0;
+ }
+ sata_dwc_bmdma_setup_by_tag(qc, tag);
+}
+
+static void sata_dwc_bmdma_start_by_tag(struct ata_queued_cmd *qc, u8 tag)
+{
+ int start_dma;
+ u32 reg, dma_chan;
+ struct sata_dwc_device *hsdev = HSDEV_FROM_QC(qc);
+ struct ata_port *ap = qc->ap;
+ struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
+ int dir = qc->dma_dir;
+ dma_chan = hsdevp->dma_chan[tag];
+
+ if (hsdevp->cmd_issued[tag] != SATA_DWC_CMD_ISSUED_NOT) {
+ start_dma = 1;
+ if (dir == DMA_TO_DEVICE)
+ hsdevp->dma_pending[tag] = SATA_DWC_DMA_PENDING_TX;
+ else
+ hsdevp->dma_pending[tag] = SATA_DWC_DMA_PENDING_RX;
+ } else {
+ dev_err(ap->dev, "%s: Command not pending cmd_issued=%d "
+ "(tag=%d) DMA NOT started\n", __func__,
+ hsdevp->cmd_issued[tag], tag);
+ start_dma = 0;
+ }
+
+ dev_dbg(ap->dev, "%s qc=%p tag: %x cmd: 0x%02x dma_dir: %s "
+ "start_dma? %x\n", __func__, qc, tag, qc->tf.command,
+ ata_get_cmd_descript(qc->dma_dir), start_dma);
+ sata_dwc_tf_dump(&(qc->tf));
+
+ if (start_dma) {
+ reg = core_scr_read(SCR_ERROR);
+ if (reg & SATA_DWC_SERROR_ERR_BITS) {
+ dev_err(ap->dev, "%s: ****** SError=0x%08x ******\n",
+ __func__, reg);
+ }
+
+ if (dir == DMA_TO_DEVICE)
+ out_le32(&hsdev->sata_dwc_regs->dmacr,
+ SATA_DWC_DMACR_TXCHEN);
+ else
+ out_le32(&hsdev->sata_dwc_regs->dmacr,
+ SATA_DWC_DMACR_RXCHEN);
+
+ /* Enable AHB DMA transfer on the specified channel */
+ dma_dwc_xfer_start(dma_chan);
+ }
+}
+
+static void sata_dwc_bmdma_start(struct ata_queued_cmd *qc)
+{
+ u8 tag = qc->tag;
+
+ if (ata_is_ncq(qc->tf.protocol)) {
+ dev_dbg(qc->ap->dev, "%s: ap->link.sactive=0x%08x tag=%d\n",
+ __func__, qc->ap->link.sactive, tag);
+ } else {
+ tag = 0;
+ }
+ dev_dbg(qc->ap->dev, "%s\n", __func__);
+ sata_dwc_bmdma_start_by_tag(qc, tag);
+}
+
+/*
+ * Function : sata_dwc_qc_prep_by_tag
+ * arguments : ata_queued_cmd *qc, u8 tag
+ * Return value : None
+ * qc_prep for a particular queued command based on tag
+ */
+static void sata_dwc_qc_prep_by_tag(struct ata_queued_cmd *qc, u8 tag)
+{
+ struct scatterlist *sg = qc->sg;
+ struct ata_port *ap = qc->ap;
+ u32 dma_chan;
+ struct sata_dwc_device *hsdev = HSDEV_FROM_AP(ap);
+ struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
+ int err;
+
+ dev_dbg(ap->dev, "%s: port=%d dma dir=%s n_elem=%d\n",
+ __func__, ap->port_no, ata_get_cmd_descript(qc->dma_dir),
+ qc->n_elem);
+
+ dma_chan = dma_dwc_xfer_setup(sg, qc->n_elem, hsdevp->llit[tag],
+ hsdevp->llit_dma[tag],
+ (void *__iomem)(&hsdev->sata_dwc_regs->\
+ dmadr), qc->dma_dir);
+ if (dma_chan < 0) {
+ dev_err(ap->dev, "%s: dma_dwc_xfer_setup returns err %d\n",
+ __func__, err);
+ return;
+ }
+ hsdevp->dma_chan[tag] = dma_chan;
+}
+
+static unsigned int sata_dwc_qc_issue(struct ata_queued_cmd *qc)
+{
+ u32 sactive;
+ u8 tag = qc->tag;
+ struct ata_port *ap = qc->ap;
+
+#ifdef DEBUG_NCQ
+ if (qc->tag > 0 || ap->link.sactive > 1)
+ dev_info(ap->dev, "%s ap id=%d cmd(0x%02x)=%s qc tag=%d "
+ "prot=%s ap active_tag=0x%08x ap sactive=0x%08x\n",
+ __func__, ap->print_id, qc->tf.command,
+ ata_get_cmd_descript(&qc->tf),
+ qc->tag, ata_get_cmd_descript(qc->tf.protocol),
+ ap->link.active_tag, ap->link.sactive);
+#endif
+
+ if (!ata_is_ncq(qc->tf.protocol))
+ tag = 0;
+ sata_dwc_qc_prep_by_tag(qc, tag);
+
+ if (ata_is_ncq(qc->tf.protocol)) {
+ sactive = core_scr_read(SCR_ACTIVE);
+ sactive |= (0x00000001 << tag);
+ core_scr_write(SCR_ACTIVE, sactive);
+
+ dev_dbg(qc->ap->dev, "%s: tag=%d ap->link.sactive = 0x%08x "
+ "sactive=0x%08x\n", __func__, tag, qc->ap->link.sactive,
+ sactive);
+
+ ap->ops->sff_tf_load(ap, &qc->tf);
+ sata_dwc_exec_command_by_tag(ap, &qc->tf, qc->tag,
+ SATA_DWC_CMD_ISSUED_PEND);
+ } else {
+ ata_sff_qc_issue(qc);
+ }
+ return 0;
+}
+
+/*
+ * Function : sata_dwc_qc_prep
+ * arguments : ata_queued_cmd *qc
+ * Return value : None
+ * qc_prep for a particular queued command
+ */
+
+static void sata_dwc_qc_prep(struct ata_queued_cmd *qc)
+{
+ if ((qc->dma_dir == DMA_NONE) || (qc->tf.protocol == ATA_PROT_PIO))
+ return;
+
+#ifdef DEBUG_NCQ
+ if (qc->tag > 0)
+ dev_info(qc->ap->dev, "%s: qc->tag=%d ap->active_tag=0x%08x\n",
+ __func__, tag, qc->ap->link.active_tag);
+
+ return ;
+#endif
+}
+
+static void sata_dwc_error_handler(struct ata_port *ap)
+{
+ ap->link.flags |= ATA_LFLAG_NO_HRST;
+ ata_sff_error_handler(ap);
+}
+
+/*
+ * scsi mid-layer and libata interface structures
+ */
+static struct scsi_host_template sata_dwc_sht = {
+ ATA_NCQ_SHT(DRV_NAME),
+ /*
+ * test-only: Currently this driver doesn't handle NCQ
+ * correctly. We enable NCQ but set the queue depth to a
+ * max of 1. This will get fixed in in a future release.
+ */
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .can_queue = ATA_DEF_QUEUE, /* ATA_MAX_QUEUE */
+ .dma_boundary = ATA_DMA_BOUNDARY,
+};
+
+static struct ata_port_operations sata_dwc_ops = {
+ .inherits = &ata_sff_port_ops,
+
+ .error_handler = sata_dwc_error_handler,
+
+ .qc_prep = sata_dwc_qc_prep,
+ .qc_issue = sata_dwc_qc_issue,
+
+ .scr_read = sata_dwc_scr_read,
+ .scr_write = sata_dwc_scr_write,
+
+ .port_start = sata_dwc_port_start,
+ .port_stop = sata_dwc_port_stop,
+
+ .bmdma_setup = sata_dwc_bmdma_setup,
+ .bmdma_start = sata_dwc_bmdma_start,
+};
+
+static const struct ata_port_info sata_dwc_port_info[] = {
+ {
+ .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+ ATA_FLAG_MMIO | ATA_FLAG_NCQ,
+ .pio_mask = 0x1f, /* pio 0-4 */
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &sata_dwc_ops,
+ },
+};
+
+static int sata_dwc_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ struct sata_dwc_device *hsdev;
+ u32 idr, versionr;
+ char *ver = (char *)&versionr;
+ u8 *base = NULL;
+ int err = 0;
+ int irq, rc;
+ struct ata_host *host;
+ struct ata_port_info pi = sata_dwc_port_info[0];
+ const struct ata_port_info *ppi[] = { &pi, NULL };
+
+ /* Allocate DWC SATA device */
+ hsdev = kmalloc(sizeof(*hsdev), GFP_KERNEL);
+ if (hsdev == NULL) {
+ dev_err(&ofdev->dev, "kmalloc failed for hsdev\n");
+ err = -ENOMEM;
+ goto error_out;
+ }
+ memset(hsdev, 0, sizeof(*hsdev));
+
+ /* Ioremap SATA registers */
+ base = of_iomap(ofdev->dev.of_node, 0);
+ if (!base) {
+ dev_err(&ofdev->dev, "ioremap failed for SATA register"
+ " address\n");
+ err = -ENODEV;
+ goto error_out;
+ }
+ hsdev->reg_base = base;
+ dev_dbg(&ofdev->dev, "ioremap done for SATA register address\n");
+
+ /* Synopsys DWC SATA specific Registers */
+ hsdev->sata_dwc_regs = (void *__iomem)(base + SATA_DWC_REG_OFFSET);
+
+ /* Allocate and fill host */
+ host = ata_host_alloc_pinfo(&ofdev->dev, ppi, SATA_DWC_MAX_PORTS);
+ if (!host) {
+ dev_err(&ofdev->dev, "ata_host_alloc_pinfo failed\n");
+ err = -ENOMEM;
+ goto error_out;
+ }
+
+ host->private_data = hsdev;
+
+ /* Setup port */
+ host->ports[0]->ioaddr.cmd_addr = base;
+ host->ports[0]->ioaddr.scr_addr = base + SATA_DWC_SCR_OFFSET;
+ host_pvt.scr_addr_sstatus = base + SATA_DWC_SCR_OFFSET;
+ sata_dwc_setup_port(&host->ports[0]->ioaddr, (unsigned long)base);
+
+ /* Read the ID and Version Registers */
+ idr = in_le32(&hsdev->sata_dwc_regs->idr);
+ versionr = in_le32(&hsdev->sata_dwc_regs->versionr);
+ dev_notice(&ofdev->dev, "id %d, controller version %c.%c%c\n",
+ idr, ver[0], ver[1], ver[2]);
+
+ /* Get SATA DMA interrupt number */
+ irq = irq_of_parse_and_map(ofdev->dev.of_node, 1);
+ if (irq == NO_IRQ) {
+ dev_err(&ofdev->dev, "no SATA DMA irq\n");
+ err = -ENODEV;
+ goto error_out;
+ }
+
+ /* Get physical SATA DMA register base address */
+ host_pvt.sata_dma_regs = of_iomap(ofdev->dev.of_node, 1);
+ if (!(host_pvt.sata_dma_regs)) {
+ dev_err(&ofdev->dev, "ioremap failed for AHBDMA register"
+ " address\n");
+ err = -ENODEV;
+ goto error_out;
+ }
+
+ /* Save dev for later use in dev_xxx() routines */
+ host_pvt.dwc_dev = &ofdev->dev;
+
+ /* Initialize AHB DMAC */
+ dma_dwc_init(hsdev, irq);
+
+ /* Enable SATA Interrupts */
+ sata_dwc_enable_interrupts(hsdev);
+
+ /* Get SATA interrupt number */
+ irq = irq_of_parse_and_map(ofdev->dev.of_node, 0);
+ if (irq == NO_IRQ) {
+ dev_err(&ofdev->dev, "no SATA DMA irq\n");
+ err = -ENODEV;
+ goto error_out;
+ }
+
+ /*
+ * Now, register with libATA core, this will also initiate the
+ * device discovery process, invoking our port_start() handler &
+ * error_handler() to execute a dummy Softreset EH session
+ */
+ rc = ata_host_activate(host, irq, sata_dwc_isr, 0, &sata_dwc_sht);
+
+ if (rc != 0)
+ dev_err(&ofdev->dev, "failed to activate host");
+
+ dev_set_drvdata(&ofdev->dev, host);
+ return 0;
+
+error_out:
+ /* Free SATA DMA resources */
+ dma_dwc_exit(hsdev);
+
+ if (base)
+ iounmap(base);
+ return err;
+}
+
+static int sata_dwc_remove(struct of_device *ofdev)
+{
+ struct device *dev = &ofdev->dev;
+ struct ata_host *host = dev_get_drvdata(dev);
+ struct sata_dwc_device *hsdev = host->private_data;
+
+ ata_host_detach(host);
+ dev_set_drvdata(dev, NULL);
+
+ /* Free SATA DMA resources */
+ dma_dwc_exit(hsdev);
+
+ iounmap(hsdev->reg_base);
+ kfree(hsdev);
+ kfree(host);
+ dev_dbg(&ofdev->dev, "done\n");
+ return 0;
+}
+
+static const struct of_device_id sata_dwc_match[] = {
+ { .compatible = "amcc,sata-460ex", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, sata_dwc_match);
+
+static struct of_platform_driver sata_dwc_driver = {
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ .of_match_table = sata_dwc_match,
+ },
+ .probe = sata_dwc_probe,
+ .remove = sata_dwc_remove,
+};
+
+static int __init sata_dwc_init(void)
+{
+ return of_register_platform_driver(&sata_dwc_driver);
+}
+
+static void __exit sata_dwc_exit(void)
+{
+ of_unregister_platform_driver(&sata_dwc_driver);
+}
+
+module_init(sata_dwc_init);
+module_exit(sata_dwc_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Mark Miesfeld <mmiesfeld@amcc.com>");
+MODULE_DESCRIPTION("DesignWare Cores SATA controller low lever driver");
+MODULE_VERSION(DRV_VERSION);
diff --git a/drivers/ata/sata_fsl.c b/drivers/ata/sata_fsl.c
index 61c89b5..18c986d 100644
--- a/drivers/ata/sata_fsl.c
+++ b/drivers/ata/sata_fsl.c
@@ -1096,7 +1096,7 @@ static void sata_fsl_host_intr(struct ata_port *ap)
{
struct sata_fsl_host_priv *host_priv = ap->host->private_data;
void __iomem *hcr_base = host_priv->hcr_base;
- u32 hstatus, qc_active = 0;
+ u32 hstatus, done_mask = 0;
struct ata_queued_cmd *qc;
u32 SError;
@@ -1116,28 +1116,28 @@ static void sata_fsl_host_intr(struct ata_port *ap)
}
/* Read command completed register */
- qc_active = ioread32(hcr_base + CC);
+ done_mask = ioread32(hcr_base + CC);
VPRINTK("Status of all queues :\n");
- VPRINTK("qc_active/CC = 0x%x, CA = 0x%x, CE=0x%x,CQ=0x%x,apqa=0x%x\n",
- qc_active,
+ VPRINTK("done_mask/CC = 0x%x, CA = 0x%x, CE=0x%x,CQ=0x%x,apqa=0x%x\n",
+ done_mask,
ioread32(hcr_base + CA),
ioread32(hcr_base + CE),
ioread32(hcr_base + CQ),
ap->qc_active);
- if (qc_active & ap->qc_active) {
+ if (done_mask & ap->qc_active) {
int i;
/* clear CC bit, this will also complete the interrupt */
- iowrite32(qc_active, hcr_base + CC);
+ iowrite32(done_mask, hcr_base + CC);
DPRINTK("Status of all queues :\n");
- DPRINTK("qc_active/CC = 0x%x, CA = 0x%x, CE=0x%x\n",
- qc_active, ioread32(hcr_base + CA),
+ DPRINTK("done_mask/CC = 0x%x, CA = 0x%x, CE=0x%x\n",
+ done_mask, ioread32(hcr_base + CA),
ioread32(hcr_base + CE));
for (i = 0; i < SATA_FSL_QUEUE_DEPTH; i++) {
- if (qc_active & (1 << i)) {
+ if (done_mask & (1 << i)) {
qc = ata_qc_from_tag(ap, i);
if (qc) {
ata_qc_complete(qc);
@@ -1164,7 +1164,7 @@ static void sata_fsl_host_intr(struct ata_port *ap)
/* Spurious Interrupt!! */
DPRINTK("spurious interrupt!!, CC = 0x%x\n",
ioread32(hcr_base + CC));
- iowrite32(qc_active, hcr_base + CC);
+ iowrite32(done_mask, hcr_base + CC);
return;
}
}
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index a476cd9..9463c71 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -2716,34 +2716,35 @@ static void mv_err_intr(struct ata_port *ap)
static void mv_process_crpb_response(struct ata_port *ap,
struct mv_crpb *response, unsigned int tag, int ncq_enabled)
{
+ u8 ata_status;
+ u16 edma_status = le16_to_cpu(response->flags);
struct ata_queued_cmd *qc = ata_qc_from_tag(ap, tag);
- if (qc) {
- u8 ata_status;
- u16 edma_status = le16_to_cpu(response->flags);
- /*
- * edma_status from a response queue entry:
- * LSB is from EDMA_ERR_IRQ_CAUSE (non-NCQ only).
- * MSB is saved ATA status from command completion.
- */
- if (!ncq_enabled) {
- u8 err_cause = edma_status & 0xff & ~EDMA_ERR_DEV;
- if (err_cause) {
- /*
- * Error will be seen/handled by mv_err_intr().
- * So do nothing at all here.
- */
- return;
- }
- }
- ata_status = edma_status >> CRPB_FLAG_STATUS_SHIFT;
- if (!ac_err_mask(ata_status))
- ata_qc_complete(qc);
- /* else: leave it for mv_err_intr() */
- } else {
+ if (unlikely(!qc)) {
ata_port_printk(ap, KERN_ERR, "%s: no qc for tag=%d\n",
__func__, tag);
+ return;
+ }
+
+ /*
+ * edma_status from a response queue entry:
+ * LSB is from EDMA_ERR_IRQ_CAUSE (non-NCQ only).
+ * MSB is saved ATA status from command completion.
+ */
+ if (!ncq_enabled) {
+ u8 err_cause = edma_status & 0xff & ~EDMA_ERR_DEV;
+ if (err_cause) {
+ /*
+ * Error will be seen/handled by
+ * mv_err_intr(). So do nothing at all here.
+ */
+ return;
+ }
}
+ ata_status = edma_status >> CRPB_FLAG_STATUS_SHIFT;
+ if (!ac_err_mask(ata_status))
+ ata_qc_complete(qc);
+ /* else: leave it for mv_err_intr() */
}
static void mv_process_crpb_entries(struct ata_port *ap, struct mv_port_priv *pp)
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 2116113..cb89ef8 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -1018,7 +1018,7 @@ static irqreturn_t nv_adma_interrupt(int irq, void *dev_instance)
NV_ADMA_STAT_CPBERR |
NV_ADMA_STAT_CMD_COMPLETE)) {
u32 check_commands = notifier_clears[i];
- int pos, error = 0;
+ int pos, rc;
if (status & NV_ADMA_STAT_CPBERR) {
/* check all active commands */
@@ -1030,10 +1030,12 @@ static irqreturn_t nv_adma_interrupt(int irq, void *dev_instance)
}
/* check CPBs for completed commands */
- while ((pos = ffs(check_commands)) && !error) {
+ while ((pos = ffs(check_commands))) {
pos--;
- error = nv_adma_check_cpb(ap, pos,
+ rc = nv_adma_check_cpb(ap, pos,
notifier_error & (1 << pos));
+ if (unlikely(rc))
+ check_commands = 0;
check_commands &= ~(1 << pos);
}
}
@@ -2129,7 +2131,6 @@ static int nv_swncq_sdbfis(struct ata_port *ap)
struct nv_swncq_port_priv *pp = ap->private_data;
struct ata_eh_info *ehi = &ap->link.eh_info;
u32 sactive;
- int nr_done = 0;
u32 done_mask;
int i;
u8 host_stat;
@@ -2170,22 +2171,21 @@ static int nv_swncq_sdbfis(struct ata_port *ap)
pp->dhfis_bits &= ~(1 << i);
pp->dmafis_bits &= ~(1 << i);
pp->sdbfis_bits |= (1 << i);
- nr_done++;
}
}
if (!ap->qc_active) {
DPRINTK("over\n");
nv_swncq_pp_reinit(ap);
- return nr_done;
+ return 0;
}
if (pp->qc_active & pp->dhfis_bits)
- return nr_done;
+ return 0;
if ((pp->ncq_flags & ncq_saw_backout) ||
(pp->qc_active ^ pp->dhfis_bits))
- /* if the controller cann't get a device to host register FIS,
+ /* if the controller can't get a device to host register FIS,
* The driver needs to reissue the new command.
*/
lack_dhfis = 1;
@@ -2202,7 +2202,7 @@ static int nv_swncq_sdbfis(struct ata_port *ap)
if (lack_dhfis) {
qc = ata_qc_from_tag(ap, pp->last_issue_tag);
nv_swncq_issue_atacmd(ap, qc);
- return nr_done;
+ return 0;
}
if (pp->defer_queue.defer_bits) {
@@ -2212,7 +2212,7 @@ static int nv_swncq_sdbfis(struct ata_port *ap)
nv_swncq_issue_atacmd(ap, qc);
}
- return nr_done;
+ return 0;
}
static inline u32 nv_swncq_tag(struct ata_port *ap)
@@ -2224,7 +2224,7 @@ static inline u32 nv_swncq_tag(struct ata_port *ap)
return (tag & 0x1f);
}
-static int nv_swncq_dmafis(struct ata_port *ap)
+static void nv_swncq_dmafis(struct ata_port *ap)
{
struct ata_queued_cmd *qc;
unsigned int rw;
@@ -2239,7 +2239,7 @@ static int nv_swncq_dmafis(struct ata_port *ap)
qc = ata_qc_from_tag(ap, tag);
if (unlikely(!qc))
- return 0;
+ return;
rw = qc->tf.flags & ATA_TFLAG_WRITE;
@@ -2254,8 +2254,6 @@ static int nv_swncq_dmafis(struct ata_port *ap)
dmactl |= ATA_DMA_WR;
iowrite8(dmactl | ATA_DMA_START, ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
-
- return 1;
}
static void nv_swncq_host_interrupt(struct ata_port *ap, u16 fis)
@@ -2265,7 +2263,6 @@ static void nv_swncq_host_interrupt(struct ata_port *ap, u16 fis)
struct ata_eh_info *ehi = &ap->link.eh_info;
u32 serror;
u8 ata_stat;
- int rc = 0;
ata_stat = ap->ops->sff_check_status(ap);
nv_swncq_irq_clear(ap, fis);
@@ -2310,8 +2307,7 @@ static void nv_swncq_host_interrupt(struct ata_port *ap, u16 fis)
"dhfis 0x%X dmafis 0x%X sactive 0x%X\n",
ap->print_id, pp->qc_active, pp->dhfis_bits,
pp->dmafis_bits, readl(pp->sactive_block));
- rc = nv_swncq_sdbfis(ap);
- if (rc < 0)
+ if (nv_swncq_sdbfis(ap) < 0)
goto irq_error;
}
@@ -2348,7 +2344,7 @@ static void nv_swncq_host_interrupt(struct ata_port *ap, u16 fis)
*/
pp->dmafis_bits |= (0x1 << nv_swncq_tag(ap));
pp->ncq_flags |= ncq_saw_dmas;
- rc = nv_swncq_dmafis(ap);
+ nv_swncq_dmafis(ap);
}
irq_exit:
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index 477345d..a0c20d9 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -1459,6 +1459,7 @@ static void quirk_jmicron_ata(struct pci_dev *pdev)
switch (pdev->device) {
case PCI_DEVICE_ID_JMICRON_JMB360: /* SATA single port */
case PCI_DEVICE_ID_JMICRON_JMB362: /* SATA dual ports */
+ case PCI_DEVICE_ID_JMICRON_JMB364: /* SATA dual ports */
/* The controller should be in single function ahci mode */
conf1 |= 0x0002A100; /* Set 8, 13, 15, 17 */
break;
@@ -1470,6 +1471,7 @@ static void quirk_jmicron_ata(struct pci_dev *pdev)
/* Fall through */
case PCI_DEVICE_ID_JMICRON_JMB361:
case PCI_DEVICE_ID_JMICRON_JMB363:
+ case PCI_DEVICE_ID_JMICRON_JMB369:
/* Enable dual function mode, AHCI on fn 0, IDE fn1 */
/* Set the class codes correctly and then direct IDE 0 */
conf1 |= 0x00C2A1B3; /* Set 0, 1, 4, 5, 7, 8, 13, 15, 17, 22, 23 */
@@ -1496,16 +1498,20 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, qui
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata);
#endif
diff --git a/include/linux/ahci_platform.h b/include/linux/ahci_platform.h
index f7dd576..be3d9a7 100644
--- a/include/linux/ahci_platform.h
+++ b/include/linux/ahci_platform.h
@@ -15,11 +15,13 @@
#ifndef _AHCI_PLATFORM_H
#define _AHCI_PLATFORM_H
+#include <linux/compiler.h>
+
struct device;
struct ata_port_info;
struct ahci_platform_data {
- int (*init)(struct device *dev);
+ int (*init)(struct device *dev, void __iomem *addr);
void (*exit)(struct device *dev);
const struct ata_port_info *ata_port_info;
unsigned int force_port_map;
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 3bedcc1..eb200e6 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -2324,9 +2324,11 @@
#define PCI_DEVICE_ID_JMICRON_JMB361 0x2361
#define PCI_DEVICE_ID_JMICRON_JMB362 0x2362
#define PCI_DEVICE_ID_JMICRON_JMB363 0x2363
+#define PCI_DEVICE_ID_JMICRON_JMB364 0x2364
#define PCI_DEVICE_ID_JMICRON_JMB365 0x2365
#define PCI_DEVICE_ID_JMICRON_JMB366 0x2366
#define PCI_DEVICE_ID_JMICRON_JMB368 0x2368
+#define PCI_DEVICE_ID_JMICRON_JMB369 0x2369
#define PCI_DEVICE_ID_JMICRON_JMB38X_SD 0x2381
#define PCI_DEVICE_ID_JMICRON_JMB38X_MMC 0x2382
#define PCI_DEVICE_ID_JMICRON_JMB38X_MS 0x2383
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2010-06-02 18:08 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2010-06-02 18:08 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-scsi, linux-ide, LKML
1) Last half of a block layer update to support the host-protected area
(HPA) on ATA disks, an ATA feature which controls whether the disk
reports full capacity (normal + host area) or reduced capacity
(normal area only).
2) various fixes
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/Kconfig | 6 +++---
drivers/ata/libata-core.c | 6 +++---
drivers/ata/libata-scsi.c | 29 +++++++++++++++++++++++++++++
drivers/ata/sata_nv.c | 2 --
drivers/ata/sata_via.c | 13 +++++++++++++
drivers/scsi/sd.c | 22 ++++++++++++++++++++++
include/linux/libata.h | 2 ++
include/scsi/scsi_host.h | 8 ++++++++
8 files changed, 80 insertions(+), 8 deletions(-)
Stefan Richter (1):
libata-sff: trivial corrections to Kconfig help text
Tejun Heo (5):
sata_via: magic vt6421 fix for transmission problems w/ WD drives
sata_nv: don't diddle with nIEN on mcp55
SCSI: implement sd_unlock_native_capacity()
libata: use the enlarged capacity after late HPA unlock
libata: implement on-demand HPA unlocking
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 73f8833..aa85a98 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -168,10 +168,10 @@ config ATA_BMDMA
default y
help
This option adds support for SFF ATA controllers with BMDMA
- capability. BMDMA stands for bus-master DMA and the
- de-facto DMA interface for SFF controllers.
+ capability. BMDMA stands for bus-master DMA and is the
+ de facto DMA interface for SFF controllers.
- If unuser, say Y.
+ If unsure, say Y.
if ATA_BMDMA
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 06b7e49..ddf8e48 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -4119,9 +4119,8 @@ int ata_dev_revalidate(struct ata_device *dev, unsigned int new_class,
dev->n_sectors > n_sectors && dev->n_sectors == n_native_sectors) {
ata_dev_printk(dev, KERN_WARNING,
"new n_sectors matches native, probably "
- "late HPA unlock, continuing\n");
- /* keep using the old n_sectors */
- dev->n_sectors = n_sectors;
+ "late HPA unlock, n_sectors updated\n");
+ /* use the larger n_sectors */
return 0;
}
@@ -6669,6 +6668,7 @@ EXPORT_SYMBOL_GPL(ata_dummy_port_info);
EXPORT_SYMBOL_GPL(ata_link_next);
EXPORT_SYMBOL_GPL(ata_dev_next);
EXPORT_SYMBOL_GPL(ata_std_bios_param);
+EXPORT_SYMBOL_GPL(ata_scsi_unlock_native_capacity);
EXPORT_SYMBOL_GPL(ata_host_init);
EXPORT_SYMBOL_GPL(ata_host_alloc);
EXPORT_SYMBOL_GPL(ata_host_alloc_pinfo);
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index cfa9dd3..a54273d 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -415,6 +415,35 @@ int ata_std_bios_param(struct scsi_device *sdev, struct block_device *bdev,
}
/**
+ * ata_scsi_unlock_native_capacity - unlock native capacity
+ * @sdev: SCSI device to adjust device capacity for
+ *
+ * This function is called if a partition on @sdev extends beyond
+ * the end of the device. It requests EH to unlock HPA.
+ *
+ * LOCKING:
+ * Defined by the SCSI layer. Might sleep.
+ */
+void ata_scsi_unlock_native_capacity(struct scsi_device *sdev)
+{
+ struct ata_port *ap = ata_shost_to_port(sdev->host);
+ struct ata_device *dev;
+ unsigned long flags;
+
+ spin_lock_irqsave(ap->lock, flags);
+
+ dev = ata_scsi_find_dev(ap, sdev);
+ if (dev && dev->n_sectors < dev->n_native_sectors) {
+ dev->flags |= ATA_DFLAG_UNLOCK_HPA;
+ dev->link->eh_info.action |= ATA_EH_RESET;
+ ata_port_schedule_eh(ap);
+ }
+
+ spin_unlock_irqrestore(ap->lock, flags);
+ ata_port_wait_eh(ap);
+}
+
+/**
* ata_get_identity - Handler for HDIO_GET_IDENTITY ioctl
* @ap: target port
* @sdev: SCSI device to get identify data for
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 6fd1147..2116113 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -1669,7 +1669,6 @@ static void nv_mcp55_freeze(struct ata_port *ap)
mask = readl(mmio_base + NV_INT_ENABLE_MCP55);
mask &= ~(NV_INT_ALL_MCP55 << shift);
writel(mask, mmio_base + NV_INT_ENABLE_MCP55);
- ata_sff_freeze(ap);
}
static void nv_mcp55_thaw(struct ata_port *ap)
@@ -1683,7 +1682,6 @@ static void nv_mcp55_thaw(struct ata_port *ap)
mask = readl(mmio_base + NV_INT_ENABLE_MCP55);
mask |= (NV_INT_MASK_MCP55 << shift);
writel(mask, mmio_base + NV_INT_ENABLE_MCP55);
- ata_sff_thaw(ap);
}
static void nv_adma_error_handler(struct ata_port *ap)
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index 101d8c2..0ecd0f6 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -575,6 +575,19 @@ static void svia_configure(struct pci_dev *pdev)
tmp8 |= NATIVE_MODE_ALL;
pci_write_config_byte(pdev, SATA_NATIVE_MODE, tmp8);
}
+
+ /*
+ * vt6421 has problems talking to some drives. The following
+ * is the magic fix from Joseph Chan <JosephChan@via.com.tw>.
+ * Please add proper documentation if possible.
+ *
+ * https://bugzilla.kernel.org/show_bug.cgi?id=15173
+ */
+ if (pdev->device == 0x3249) {
+ pci_read_config_byte(pdev, 0x52, &tmp8);
+ tmp8 |= 1 << 2;
+ pci_write_config_byte(pdev, 0x52, tmp8);
+ }
}
static int svia_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
diff --git a/drivers/scsi/sd.c b/drivers/scsi/sd.c
index 829cc37..8802e48 100644
--- a/drivers/scsi/sd.c
+++ b/drivers/scsi/sd.c
@@ -97,6 +97,7 @@ MODULE_ALIAS_SCSI_DEVICE(TYPE_RBC);
#endif
static int sd_revalidate_disk(struct gendisk *);
+static void sd_unlock_native_capacity(struct gendisk *disk);
static int sd_probe(struct device *);
static int sd_remove(struct device *);
static void sd_shutdown(struct device *);
@@ -1101,6 +1102,7 @@ static const struct block_device_operations sd_fops = {
#endif
.media_changed = sd_media_changed,
.revalidate_disk = sd_revalidate_disk,
+ .unlock_native_capacity = sd_unlock_native_capacity,
};
static unsigned int sd_completed_bytes(struct scsi_cmnd *scmd)
@@ -2121,6 +2123,26 @@ static int sd_revalidate_disk(struct gendisk *disk)
}
/**
+ * sd_unlock_native_capacity - unlock native capacity
+ * @disk: struct gendisk to set capacity for
+ *
+ * Block layer calls this function if it detects that partitions
+ * on @disk reach beyond the end of the device. If the SCSI host
+ * implements ->unlock_native_capacity() method, it's invoked to
+ * give it a chance to adjust the device capacity.
+ *
+ * CONTEXT:
+ * Defined by block layer. Might sleep.
+ */
+static void sd_unlock_native_capacity(struct gendisk *disk)
+{
+ struct scsi_device *sdev = scsi_disk(disk)->device;
+
+ if (sdev->host->hostt->unlock_native_capacity)
+ sdev->host->hostt->unlock_native_capacity(sdev);
+}
+
+/**
* sd_format_disk_name - format disk name
* @prefix: name prefix - ie. "sd" for SCSI disks
* @index: index of the disk to format name for
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 3bad270..b85f3ff 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1023,6 +1023,7 @@ extern void ata_scsi_simulate(struct ata_device *dev, struct scsi_cmnd *cmd,
extern int ata_std_bios_param(struct scsi_device *sdev,
struct block_device *bdev,
sector_t capacity, int geom[]);
+extern void ata_scsi_unlock_native_capacity(struct scsi_device *sdev);
extern int ata_scsi_slave_config(struct scsi_device *sdev);
extern void ata_scsi_slave_destroy(struct scsi_device *sdev);
extern int ata_scsi_change_queue_depth(struct scsi_device *sdev,
@@ -1174,6 +1175,7 @@ extern struct device_attribute *ata_common_sdev_attrs[];
.slave_configure = ata_scsi_slave_config, \
.slave_destroy = ata_scsi_slave_destroy, \
.bios_param = ata_std_bios_param, \
+ .unlock_native_capacity = ata_scsi_unlock_native_capacity, \
.sdev_attrs = ata_common_sdev_attrs
#define ATA_NCQ_SHT(drv_name) \
diff --git a/include/scsi/scsi_host.h b/include/scsi/scsi_host.h
index c50a97f..b7bdecb 100644
--- a/include/scsi/scsi_host.h
+++ b/include/scsi/scsi_host.h
@@ -327,6 +327,14 @@ struct scsi_host_template {
sector_t, int []);
/*
+ * This function is called when one or more partitions on the
+ * device reach beyond the end of the device.
+ *
+ * Status: OPTIONAL
+ */
+ void (*unlock_native_capacity)(struct scsi_device *);
+
+ /*
* Can be used to export driver statistics and other infos to the
* world outside the kernel ie. userspace and it also provides an
* interface to feed the driver with information.
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2010-05-28 1:18 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2010-05-28 1:18 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
1) Finish Tejun's SFF<->BMDMA separation patchset, as mentioned in
initial 2.6.35 push. These had been submitted prior to merge
window open, but had to wait to resolve some patch/merge conflicts.
2) Disable Asynchronous Notification (AN) by default. Proper use
is vague, and behavior of firmwares in the field do not match each
other.
3) add 'dump_id' debugging output helper, to give us better bug reports
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
Documentation/kernel-parameters.txt | 2 +
drivers/ata/Kconfig | 511 ++++++++++++++++++-----------------
drivers/ata/Makefile | 83 ++++---
drivers/ata/ata_generic.c | 2 +-
drivers/ata/ata_piix.c | 4 +-
drivers/ata/libata-core.c | 16 +-
drivers/ata/libata-sff.c | 416 ++++++++++++++++++++---------
drivers/ata/pata_acpi.c | 2 +-
drivers/ata/pata_ali.c | 5 +-
drivers/ata/pata_amd.c | 2 +-
drivers/ata/pata_artop.c | 2 +-
drivers/ata/pata_atiixp.c | 4 +-
drivers/ata/pata_atp867x.c | 2 +-
drivers/ata/pata_bf54x.c | 2 +-
drivers/ata/pata_cmd64x.c | 2 +-
drivers/ata/pata_cs5520.c | 2 +-
drivers/ata/pata_cs5530.c | 2 +-
drivers/ata/pata_cs5535.c | 2 +-
drivers/ata/pata_cs5536.c | 2 +-
drivers/ata/pata_cypress.c | 2 +-
drivers/ata/pata_efar.c | 4 +-
drivers/ata/pata_hpt366.c | 2 +-
drivers/ata/pata_hpt37x.c | 2 +-
drivers/ata/pata_hpt3x2n.c | 2 +-
drivers/ata/pata_hpt3x3.c | 2 +-
drivers/ata/pata_icside.c | 2 +-
drivers/ata/pata_it8213.c | 2 +-
drivers/ata/pata_it821x.c | 2 +-
drivers/ata/pata_jmicron.c | 2 +-
drivers/ata/pata_macio.c | 2 +-
drivers/ata/pata_marvell.c | 2 +-
drivers/ata/pata_mpc52xx.c | 2 +-
drivers/ata/pata_netcell.c | 2 +-
drivers/ata/pata_ninja32.c | 2 +-
drivers/ata/pata_ns87415.c | 2 +-
drivers/ata/pata_octeon_cf.c | 18 --
drivers/ata/pata_oldpiix.c | 2 +-
drivers/ata/pata_optidma.c | 2 +-
drivers/ata/pata_pdc2027x.c | 2 +-
drivers/ata/pata_pdc202xx_old.c | 2 +-
drivers/ata/pata_piccolo.c | 2 +-
drivers/ata/pata_radisys.c | 2 +-
drivers/ata/pata_rdc.c | 4 +-
drivers/ata/pata_sc1200.c | 2 +-
drivers/ata/pata_scc.c | 4 +-
drivers/ata/pata_sch.c | 2 +-
drivers/ata/pata_serverworks.c | 2 +-
drivers/ata/pata_sil680.c | 4 +-
drivers/ata/pata_sis.c | 2 +-
drivers/ata/pata_sl82c105.c | 2 +-
drivers/ata/pata_triflex.c | 2 +-
drivers/ata/pata_via.c | 2 +-
drivers/ata/sata_mv.c | 4 +-
drivers/ata/sata_nv.c | 8 +-
drivers/ata/sata_qstor.c | 16 +-
drivers/ata/sata_sil.c | 4 +-
drivers/ata/sata_sis.c | 4 +-
drivers/ata/sata_svw.c | 2 +-
drivers/ata/sata_uli.c | 2 +-
drivers/ata/sata_via.c | 8 +-
drivers/ata/sata_vsc.c | 2 +-
include/linux/libata.h | 36 ++-
62 files changed, 720 insertions(+), 519 deletions(-)
Tejun Heo (8):
sata_mv: drop unncessary EH callback resetting
libata-sff: ata_sff_irq_clear() is BMDMA specific
libata-sff: separate out BMDMA irq handler
libata-sff: separate out BMDMA init
libata-sff: kill dummy BMDMA ops from sata_qstor and pata_octeon_cf
libata-sff: make BMDMA optional
libata: disable ATAPI AN by default
libata: implement dump_id force param
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index b56ea86..a5c0550 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -1252,6 +1252,8 @@ and is between 256 and 4096 characters. It is defined in the file
* nohrst, nosrst, norst: suppress hard, soft
and both resets.
+ * dump_id: dump IDENTIFY data.
+
If there are multiple matching configurations changing
the same attribute, the last one is used.
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index e68541f..73f8833 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -57,6 +57,8 @@ config SATA_PMP
This option adds support for SATA Port Multipliers
(the SATA version of an ethernet hub, or SAS expander).
+comment "Controllers with non-SFF native interface"
+
config SATA_AHCI
tristate "AHCI SATA support"
depends on PCI
@@ -73,11 +75,12 @@ config SATA_AHCI_PLATFORM
If unsure, say N.
-config SATA_SIL24
- tristate "Silicon Image 3124/3132 SATA support"
- depends on PCI
+config SATA_FSL
+ tristate "Freescale 3.0Gbps SATA support"
+ depends on FSL_SOC
help
- This option enables support for Silicon Image 3124/3132 Serial ATA.
+ This option enables support for Freescale 3.0Gbps SATA controller.
+ It can be found on MPC837x and MPC8315.
If unsure, say N.
@@ -87,12 +90,11 @@ config SATA_INIC162X
help
This option enables support for Initio 162x Serial ATA.
-config SATA_FSL
- tristate "Freescale 3.0Gbps SATA support"
- depends on FSL_SOC
+config SATA_SIL24
+ tristate "Silicon Image 3124/3132 SATA support"
+ depends on PCI
help
- This option enables support for Freescale 3.0Gbps SATA controller.
- It can be found on MPC837x and MPC8315.
+ This option enables support for Silicon Image 3124/3132 Serial ATA.
If unsure, say N.
@@ -116,15 +118,65 @@ config ATA_SFF
if ATA_SFF
-config SATA_SVW
- tristate "ServerWorks Frodo / Apple K2 SATA support"
+comment "SFF controllers with custom DMA interface"
+
+config PDC_ADMA
+ tristate "Pacific Digital ADMA support"
depends on PCI
help
- This option enables support for Broadcom/Serverworks/Apple K2
- SATA support.
+ This option enables support for Pacific Digital ADMA controllers
+
+ If unsure, say N.
+
+config PATA_MPC52xx
+ tristate "Freescale MPC52xx SoC internal IDE"
+ depends on PPC_MPC52xx && PPC_BESTCOMM
+ select PPC_BESTCOMM_ATA
+ help
+ This option enables support for integrated IDE controller
+ of the Freescale MPC52xx SoC.
+
+ If unsure, say N.
+
+config PATA_OCTEON_CF
+ tristate "OCTEON Boot Bus Compact Flash support"
+ depends on CPU_CAVIUM_OCTEON
+ help
+ This option enables a polled compact flash driver for use with
+ compact flash cards attached to the OCTEON boot bus.
+
+ If unsure, say N.
+
+config SATA_QSTOR
+ tristate "Pacific Digital SATA QStor support"
+ depends on PCI
+ help
+ This option enables support for Pacific Digital Serial ATA QStor.
+
+ If unsure, say N.
+
+config SATA_SX4
+ tristate "Promise SATA SX4 support (Experimental)"
+ depends on PCI && EXPERIMENTAL
+ help
+ This option enables support for Promise Serial ATA SX4.
If unsure, say N.
+config ATA_BMDMA
+ bool "ATA BMDMA support"
+ default y
+ help
+ This option adds support for SFF ATA controllers with BMDMA
+ capability. BMDMA stands for bus-master DMA and the
+ de-facto DMA interface for SFF controllers.
+
+ If unuser, say Y.
+
+if ATA_BMDMA
+
+comment "SATA SFF controllers with BMDMA"
+
config ATA_PIIX
tristate "Intel ESB, ICH, PIIX3, PIIX4 PATA/SATA support"
depends on PCI
@@ -152,22 +204,6 @@ config SATA_NV
If unsure, say N.
-config PDC_ADMA
- tristate "Pacific Digital ADMA support"
- depends on PCI
- help
- This option enables support for Pacific Digital ADMA controllers
-
- If unsure, say N.
-
-config SATA_QSTOR
- tristate "Pacific Digital SATA QStor support"
- depends on PCI
- help
- This option enables support for Pacific Digital Serial ATA QStor.
-
- If unsure, say N.
-
config SATA_PROMISE
tristate "Promise SATA TX2/TX4 support"
depends on PCI
@@ -176,14 +212,6 @@ config SATA_PROMISE
If unsure, say N.
-config SATA_SX4
- tristate "Promise SATA SX4 support (Experimental)"
- depends on PCI && EXPERIMENTAL
- help
- This option enables support for Promise Serial ATA SX4.
-
- If unsure, say N.
-
config SATA_SIL
tristate "Silicon Image SATA support"
depends on PCI
@@ -203,6 +231,15 @@ config SATA_SIS
enable the PATA_SIS driver in the config.
If unsure, say N.
+config SATA_SVW
+ tristate "ServerWorks Frodo / Apple K2 SATA support"
+ depends on PCI
+ help
+ This option enables support for Broadcom/Serverworks/Apple K2
+ SATA support.
+
+ If unsure, say N.
+
config SATA_ULI
tristate "ULi Electronics SATA support"
depends on PCI
@@ -227,14 +264,7 @@ config SATA_VITESSE
If unsure, say N.
-config PATA_ACPI
- tristate "ACPI firmware driver for PATA"
- depends on ATA_ACPI
- help
- This option enables an ACPI method driver which drives
- motherboard PATA controller interfaces through the ACPI
- firmware in the BIOS. This driver can sometimes handle
- otherwise unsupported hardware.
+comment "PATA SFF controllers with BMDMA"
config PATA_ALI
tristate "ALi PATA support"
@@ -262,40 +292,30 @@ config PATA_ARTOP
If unsure, say N.
-config PATA_ATP867X
- tristate "ARTOP/Acard ATP867X PATA support"
+config PATA_ATIIXP
+ tristate "ATI PATA support"
depends on PCI
help
- This option enables support for ARTOP/Acard ATP867X PATA
- controllers.
-
- If unsure, say N.
-
-config PATA_AT32
- tristate "Atmel AVR32 PATA support (Experimental)"
- depends on AVR32 && PLATFORM_AT32AP && EXPERIMENTAL
- help
- This option enables support for the IDE devices on the
- Atmel AT32AP platform.
+ This option enables support for the ATI ATA interfaces
+ found on the many ATI chipsets.
If unsure, say N.
-config PATA_ATIIXP
- tristate "ATI PATA support"
+config PATA_ATP867X
+ tristate "ARTOP/Acard ATP867X PATA support"
depends on PCI
help
- This option enables support for the ATI ATA interfaces
- found on the many ATI chipsets.
+ This option enables support for ARTOP/Acard ATP867X PATA
+ controllers.
If unsure, say N.
-config PATA_CMD640_PCI
- tristate "CMD640 PCI PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+config PATA_BF54X
+ tristate "Blackfin 54x ATAPI support"
+ depends on BF542 || BF548 || BF549
help
- This option enables support for the CMD640 PCI IDE
- interface chip. Only the primary channel is currently
- supported.
+ This option enables support for the built-in ATAPI controller on
+ Blackfin 54x family chips.
If unsure, say N.
@@ -362,15 +382,6 @@ config PATA_EFAR
If unsure, say N.
-config ATA_GENERIC
- tristate "Generic ATA support"
- depends on PCI
- help
- This option enables support for generic BIOS configured
- ATA controllers via the new ATA layer
-
- If unsure, say N.
-
config PATA_HPT366
tristate "HPT 366/368 PATA support"
depends on PCI
@@ -415,12 +426,20 @@ config PATA_HPT3X3_DMA
controllers. Enable with care as there are still some
problems with DMA on this chipset.
-config PATA_ISAPNP
- tristate "ISA Plug and Play PATA support"
- depends on ISAPNP
+config PATA_ICSIDE
+ tristate "Acorn ICS PATA support"
+ depends on ARM && ARCH_ACORN
help
- This option enables support for ISA plug & play ATA
- controllers such as those found on old soundcards.
+ On Acorn systems, say Y here if you wish to use the ICS PATA
+ interface card. This is not required for ICS partition support.
+ If you are unsure, say N to this.
+
+config PATA_IT8213
+ tristate "IT8213 PATA support (Experimental)"
+ depends on PCI && EXPERIMENTAL
+ help
+ This option enables support for the ITE 821 PATA
+ controllers via the new ATA layer.
If unsure, say N.
@@ -434,15 +453,6 @@ config PATA_IT821X
If unsure, say N.
-config PATA_IT8213
- tristate "IT8213 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
- help
- This option enables support for the ITE 821 PATA
- controllers via the new ATA layer.
-
- If unsure, say N.
-
config PATA_JMICRON
tristate "JMicron PATA support"
depends on PCI
@@ -452,23 +462,14 @@ config PATA_JMICRON
If unsure, say N.
-config PATA_LEGACY
- tristate "Legacy ISA PATA support (Experimental)"
- depends on (ISA || PCI) && EXPERIMENTAL
- help
- This option enables support for ISA/VLB/PCI bus legacy PATA
- ports and allows them to be accessed via the new ATA layer.
-
- If unsure, say N.
-
-config PATA_TRIFLEX
- tristate "Compaq Triflex PATA support"
- depends on PCI
+config PATA_MACIO
+ tristate "Apple PowerMac/PowerBook internal 'MacIO' IDE"
+ depends on PPC_PMAC
help
- Enable support for the Compaq 'Triflex' IDE controller as found
- on many Compaq Pentium-Pro systems, via the new ATA layer.
-
- If unsure, say N.
+ Most IDE capable PowerMacs have IDE busses driven by a variant
+ of this controller which is part of the Apple chipset used on
+ most PowerMac models. Some models have multiple busses using
+ different chipsets, though generally, MacIO is one of them.
config PATA_MARVELL
tristate "Marvell PATA support via legacy mode"
@@ -481,32 +482,6 @@ config PATA_MARVELL
If unsure, say N.
-config PATA_MPC52xx
- tristate "Freescale MPC52xx SoC internal IDE"
- depends on PPC_MPC52xx && PPC_BESTCOMM
- select PPC_BESTCOMM_ATA
- help
- This option enables support for integrated IDE controller
- of the Freescale MPC52xx SoC.
-
- If unsure, say N.
-
-config PATA_MPIIX
- tristate "Intel PATA MPIIX support"
- depends on PCI
- help
- This option enables support for MPIIX PATA support.
-
- If unsure, say N.
-
-config PATA_OLDPIIX
- tristate "Intel PATA old PIIX support"
- depends on PCI
- help
- This option enables support for early PIIX PATA support.
-
- If unsure, say N.
-
config PATA_NETCELL
tristate "NETCELL Revolution RAID support"
depends on PCI
@@ -525,15 +500,6 @@ config PATA_NINJA32
If unsure, say N.
-config PATA_NS87410
- tristate "Nat Semi NS87410 PATA support"
- depends on PCI
- help
- This option enables support for the National Semiconductor
- NS87410 PCI-IDE controller.
-
- If unsure, say N.
-
config PATA_NS87415
tristate "Nat Semi NS87415 PATA support"
depends on PCI
@@ -543,12 +509,11 @@ config PATA_NS87415
If unsure, say N.
-config PATA_OPTI
- tristate "OPTI621/6215 PATA support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+config PATA_OLDPIIX
+ tristate "Intel PATA old PIIX support"
+ depends on PCI
help
- This option enables full PIO support for the early Opti ATA
- controllers found on some old motherboards.
+ This option enables support for early PIIX PATA support.
If unsure, say N.
@@ -562,24 +527,6 @@ config PATA_OPTIDMA
If unsure, say N.
-config PATA_PALMLD
- tristate "Palm LifeDrive PATA support"
- depends on MACH_PALMLD
- help
- This option enables support for Palm LifeDrive's internal ATA
- port via the new ATA layer.
-
- If unsure, say N.
-
-config PATA_PCMCIA
- tristate "PCMCIA PATA support"
- depends on PCMCIA
- help
- This option enables support for PCMCIA ATA interfaces, including
- compact flash card adapters via the new ATA layer.
-
- If unsure, say N.
-
config PATA_PDC2027X
tristate "Promise PATA 2027x support"
depends on PCI
@@ -597,12 +544,6 @@ config PATA_PDC_OLD
If unsure, say N.
-config PATA_QDI
- tristate "QDI VLB PATA support"
- depends on ISA
- help
- Support for QDI 6500 and 6580 PATA controllers on VESA local bus.
-
config PATA_RADISYS
tristate "RADISYS 82600 PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
@@ -612,15 +553,6 @@ config PATA_RADISYS
If unsure, say N.
-config PATA_RB532
- tristate "RouterBoard 532 PATA CompactFlash support"
- depends on MIKROTIK_RB532
- help
- This option enables support for the RouterBoard 532
- PATA CompactFlash controller.
-
- If unsure, say N.
-
config PATA_RDC
tristate "RDC PATA support"
depends on PCI
@@ -631,21 +563,30 @@ config PATA_RDC
If unsure, say N.
-config PATA_RZ1000
- tristate "PC Tech RZ1000 PATA support"
+config PATA_SC1200
+ tristate "SC1200 PATA support"
depends on PCI
help
- This option enables basic support for the PC Tech RZ1000/1
- PATA controllers via the new ATA layer
+ This option enables support for the NatSemi/AMD SC1200 SoC
+ companion chip used with the Geode processor family.
If unsure, say N.
-config PATA_SC1200
- tristate "SC1200 PATA support"
+config PATA_SCC
+ tristate "Toshiba's Cell Reference Set IDE support"
+ depends on PCI && PPC_CELLEB
+ help
+ This option enables support for the built-in IDE controller on
+ Toshiba Cell Reference Board.
+
+ If unsure, say N.
+
+config PATA_SCH
+ tristate "Intel SCH PATA support"
depends on PCI
help
- This option enables support for the NatSemi/AMD SC1200 SoC
- companion chip used with the Geode processor family.
+ This option enables support for Intel SCH PATA on the Intel
+ SCH (US15W, US15L, UL11L) series host controllers.
If unsure, say N.
@@ -683,6 +624,15 @@ config PATA_TOSHIBA
If unsure, say N.
+config PATA_TRIFLEX
+ tristate "Compaq Triflex PATA support"
+ depends on PCI
+ help
+ Enable support for the Compaq 'Triflex' IDE controller as found
+ on many Compaq Pentium-Pro systems, via the new ATA layer.
+
+ If unsure, say N.
+
config PATA_VIA
tristate "VIA PATA support"
depends on PCI
@@ -701,12 +651,99 @@ config PATA_WINBOND
If unsure, say N.
-config PATA_WINBOND_VLB
- tristate "Winbond W83759A VLB PATA support (Experimental)"
- depends on ISA && EXPERIMENTAL
+endif # ATA_BMDMA
+
+comment "PIO-only SFF controllers"
+
+config PATA_AT32
+ tristate "Atmel AVR32 PATA support (Experimental)"
+ depends on AVR32 && PLATFORM_AT32AP && EXPERIMENTAL
help
- Support for the Winbond W83759A controller on Vesa Local Bus
- systems.
+ This option enables support for the IDE devices on the
+ Atmel AT32AP platform.
+
+ If unsure, say N.
+
+config PATA_AT91
+ tristate "PATA support for AT91SAM9260"
+ depends on ARM && ARCH_AT91
+ help
+ This option enables support for IDE devices on the Atmel AT91SAM9260 SoC.
+
+ If unsure, say N.
+
+config PATA_CMD640_PCI
+ tristate "CMD640 PCI PATA support (Experimental)"
+ depends on PCI && EXPERIMENTAL
+ help
+ This option enables support for the CMD640 PCI IDE
+ interface chip. Only the primary channel is currently
+ supported.
+
+ If unsure, say N.
+
+config PATA_ISAPNP
+ tristate "ISA Plug and Play PATA support"
+ depends on ISAPNP
+ help
+ This option enables support for ISA plug & play ATA
+ controllers such as those found on old soundcards.
+
+ If unsure, say N.
+
+config PATA_IXP4XX_CF
+ tristate "IXP4XX Compact Flash support"
+ depends on ARCH_IXP4XX
+ help
+ This option enables support for a Compact Flash connected on
+ the ixp4xx expansion bus. This driver had been written for
+ Loft/Avila boards in mind but can work with others.
+
+ If unsure, say N.
+
+config PATA_MPIIX
+ tristate "Intel PATA MPIIX support"
+ depends on PCI
+ help
+ This option enables support for MPIIX PATA support.
+
+ If unsure, say N.
+
+config PATA_NS87410
+ tristate "Nat Semi NS87410 PATA support"
+ depends on PCI
+ help
+ This option enables support for the National Semiconductor
+ NS87410 PCI-IDE controller.
+
+ If unsure, say N.
+
+config PATA_OPTI
+ tristate "OPTI621/6215 PATA support (Very Experimental)"
+ depends on PCI && EXPERIMENTAL
+ help
+ This option enables full PIO support for the early Opti ATA
+ controllers found on some old motherboards.
+
+ If unsure, say N.
+
+config PATA_PALMLD
+ tristate "Palm LifeDrive PATA support"
+ depends on MACH_PALMLD
+ help
+ This option enables support for Palm LifeDrive's internal ATA
+ port via the new ATA layer.
+
+ If unsure, say N.
+
+config PATA_PCMCIA
+ tristate "PCMCIA PATA support"
+ depends on PCMCIA
+ help
+ This option enables support for PCMCIA ATA interfaces, including
+ compact flash card adapters via the new ATA layer.
+
+ If unsure, say N.
config HAVE_PATA_PLATFORM
bool
@@ -725,14 +762,6 @@ config PATA_PLATFORM
If unsure, say N.
-config PATA_AT91
- tristate "PATA support for AT91SAM9260"
- depends on ARM && ARCH_AT91
- help
- This option enables support for IDE devices on the Atmel AT91SAM9260 SoC.
-
- If unsure, say N.
-
config PATA_OF_PLATFORM
tristate "OpenFirmware platform device PATA support"
depends on PATA_PLATFORM && PPC_OF
@@ -743,69 +772,65 @@ config PATA_OF_PLATFORM
If unsure, say N.
-config PATA_ICSIDE
- tristate "Acorn ICS PATA support"
- depends on ARM && ARCH_ACORN
+config PATA_QDI
+ tristate "QDI VLB PATA support"
+ depends on ISA
help
- On Acorn systems, say Y here if you wish to use the ICS PATA
- interface card. This is not required for ICS partition support.
- If you are unsure, say N to this.
+ Support for QDI 6500 and 6580 PATA controllers on VESA local bus.
-config PATA_IXP4XX_CF
- tristate "IXP4XX Compact Flash support"
- depends on ARCH_IXP4XX
+config PATA_RB532
+ tristate "RouterBoard 532 PATA CompactFlash support"
+ depends on MIKROTIK_RB532
help
- This option enables support for a Compact Flash connected on
- the ixp4xx expansion bus. This driver had been written for
- Loft/Avila boards in mind but can work with others.
+ This option enables support for the RouterBoard 532
+ PATA CompactFlash controller.
If unsure, say N.
-config PATA_OCTEON_CF
- tristate "OCTEON Boot Bus Compact Flash support"
- depends on CPU_CAVIUM_OCTEON
+config PATA_RZ1000
+ tristate "PC Tech RZ1000 PATA support"
+ depends on PCI
help
- This option enables a polled compact flash driver for use with
- compact flash cards attached to the OCTEON boot bus.
+ This option enables basic support for the PC Tech RZ1000/1
+ PATA controllers via the new ATA layer
If unsure, say N.
-config PATA_SCC
- tristate "Toshiba's Cell Reference Set IDE support"
- depends on PCI && PPC_CELLEB
+config PATA_WINBOND_VLB
+ tristate "Winbond W83759A VLB PATA support (Experimental)"
+ depends on ISA && EXPERIMENTAL
help
- This option enables support for the built-in IDE controller on
- Toshiba Cell Reference Board.
+ Support for the Winbond W83759A controller on Vesa Local Bus
+ systems.
- If unsure, say N.
+comment "Generic fallback / legacy drivers"
-config PATA_SCH
- tristate "Intel SCH PATA support"
- depends on PCI
+config PATA_ACPI
+ tristate "ACPI firmware driver for PATA"
+ depends on ATA_ACPI && ATA_BMDMA
help
- This option enables support for Intel SCH PATA on the Intel
- SCH (US15W, US15L, UL11L) series host controllers.
-
- If unsure, say N.
+ This option enables an ACPI method driver which drives
+ motherboard PATA controller interfaces through the ACPI
+ firmware in the BIOS. This driver can sometimes handle
+ otherwise unsupported hardware.
-config PATA_BF54X
- tristate "Blackfin 54x ATAPI support"
- depends on BF542 || BF548 || BF549
+config ATA_GENERIC
+ tristate "Generic ATA support"
+ depends on PCI && ATA_BMDMA
help
- This option enables support for the built-in ATAPI controller on
- Blackfin 54x family chips.
+ This option enables support for generic BIOS configured
+ ATA controllers via the new ATA layer
If unsure, say N.
-config PATA_MACIO
- tristate "Apple PowerMac/PowerBook internal 'MacIO' IDE"
- depends on PPC_PMAC
+config PATA_LEGACY
+ tristate "Legacy ISA PATA support (Experimental)"
+ depends on (ISA || PCI) && EXPERIMENTAL
help
- Most IDE capable PowerMacs have IDE busses driven by a variant
- of this controller which is part of the Apple chipset used on
- most PowerMac models. Some models have multiple busses using
- different chipsets, though generally, MacIO is one of them.
+ This option enables support for ISA/VLB/PCI bus legacy PATA
+ ports and allows them to be accessed via the new ATA layer.
+ If unsure, say N.
endif # ATA_SFF
endif # ATA
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index d0a93c4..7ef89d7 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -1,33 +1,39 @@
obj-$(CONFIG_ATA) += libata.o
+# non-SFF interface
obj-$(CONFIG_SATA_AHCI) += ahci.o libahci.o
obj-$(CONFIG_SATA_AHCI_PLATFORM) += ahci_platform.o libahci.o
-obj-$(CONFIG_SATA_SVW) += sata_svw.o
+obj-$(CONFIG_SATA_FSL) += sata_fsl.o
+obj-$(CONFIG_SATA_INIC162X) += sata_inic162x.o
+obj-$(CONFIG_SATA_SIL24) += sata_sil24.o
+
+# SFF w/ custom DMA
+obj-$(CONFIG_PDC_ADMA) += pdc_adma.o
+obj-$(CONFIG_PATA_MPC52xx) += pata_mpc52xx.o
+obj-$(CONFIG_PATA_OCTEON_CF) += pata_octeon_cf.o
+obj-$(CONFIG_SATA_QSTOR) += sata_qstor.o
+obj-$(CONFIG_SATA_SX4) += sata_sx4.o
+
+# SFF SATA w/ BMDMA
obj-$(CONFIG_ATA_PIIX) += ata_piix.o
+obj-$(CONFIG_SATA_MV) += sata_mv.o
+obj-$(CONFIG_SATA_NV) += sata_nv.o
obj-$(CONFIG_SATA_PROMISE) += sata_promise.o
-obj-$(CONFIG_SATA_QSTOR) += sata_qstor.o
obj-$(CONFIG_SATA_SIL) += sata_sil.o
-obj-$(CONFIG_SATA_SIL24) += sata_sil24.o
-obj-$(CONFIG_SATA_VIA) += sata_via.o
-obj-$(CONFIG_SATA_VITESSE) += sata_vsc.o
obj-$(CONFIG_SATA_SIS) += sata_sis.o
-obj-$(CONFIG_SATA_SX4) += sata_sx4.o
-obj-$(CONFIG_SATA_NV) += sata_nv.o
+obj-$(CONFIG_SATA_SVW) += sata_svw.o
obj-$(CONFIG_SATA_ULI) += sata_uli.o
-obj-$(CONFIG_SATA_MV) += sata_mv.o
-obj-$(CONFIG_SATA_INIC162X) += sata_inic162x.o
-obj-$(CONFIG_PDC_ADMA) += pdc_adma.o
-obj-$(CONFIG_SATA_FSL) += sata_fsl.o
-obj-$(CONFIG_PATA_MACIO) += pata_macio.o
+obj-$(CONFIG_SATA_VIA) += sata_via.o
+obj-$(CONFIG_SATA_VITESSE) += sata_vsc.o
+# SFF PATA w/ BMDMA
obj-$(CONFIG_PATA_ALI) += pata_ali.o
obj-$(CONFIG_PATA_AMD) += pata_amd.o
obj-$(CONFIG_PATA_ARTOP) += pata_artop.o
-obj-$(CONFIG_PATA_ATP867X) += pata_atp867x.o
-obj-$(CONFIG_PATA_AT32) += pata_at32.o
obj-$(CONFIG_PATA_ATIIXP) += pata_atiixp.o
-obj-$(CONFIG_PATA_CMD640_PCI) += pata_cmd640.o
+obj-$(CONFIG_PATA_ATP867X) += pata_atp867x.o
+obj-$(CONFIG_PATA_BF54X) += pata_bf54x.o
obj-$(CONFIG_PATA_CMD64X) += pata_cmd64x.o
obj-$(CONFIG_PATA_CS5520) += pata_cs5520.o
obj-$(CONFIG_PATA_CS5530) += pata_cs5530.o
@@ -39,47 +45,50 @@ obj-$(CONFIG_PATA_HPT366) += pata_hpt366.o
obj-$(CONFIG_PATA_HPT37X) += pata_hpt37x.o
obj-$(CONFIG_PATA_HPT3X2N) += pata_hpt3x2n.o
obj-$(CONFIG_PATA_HPT3X3) += pata_hpt3x3.o
-obj-$(CONFIG_PATA_ISAPNP) += pata_isapnp.o
-obj-$(CONFIG_PATA_IT821X) += pata_it821x.o
+obj-$(CONFIG_PATA_ICSIDE) += pata_icside.o
obj-$(CONFIG_PATA_IT8213) += pata_it8213.o
+obj-$(CONFIG_PATA_IT821X) += pata_it821x.o
obj-$(CONFIG_PATA_JMICRON) += pata_jmicron.o
+obj-$(CONFIG_PATA_MACIO) += pata_macio.o
+obj-$(CONFIG_PATA_MARVELL) += pata_marvell.o
obj-$(CONFIG_PATA_NETCELL) += pata_netcell.o
obj-$(CONFIG_PATA_NINJA32) += pata_ninja32.o
-obj-$(CONFIG_PATA_NS87410) += pata_ns87410.o
obj-$(CONFIG_PATA_NS87415) += pata_ns87415.o
-obj-$(CONFIG_PATA_OPTI) += pata_opti.o
-obj-$(CONFIG_PATA_OPTIDMA) += pata_optidma.o
-obj-$(CONFIG_PATA_MPC52xx) += pata_mpc52xx.o
-obj-$(CONFIG_PATA_MARVELL) += pata_marvell.o
-obj-$(CONFIG_PATA_MPIIX) += pata_mpiix.o
obj-$(CONFIG_PATA_OLDPIIX) += pata_oldpiix.o
-obj-$(CONFIG_PATA_PALMLD) += pata_palmld.o
-obj-$(CONFIG_PATA_PCMCIA) += pata_pcmcia.o
+obj-$(CONFIG_PATA_OPTIDMA) += pata_optidma.o
obj-$(CONFIG_PATA_PDC2027X) += pata_pdc2027x.o
obj-$(CONFIG_PATA_PDC_OLD) += pata_pdc202xx_old.o
-obj-$(CONFIG_PATA_QDI) += pata_qdi.o
obj-$(CONFIG_PATA_RADISYS) += pata_radisys.o
-obj-$(CONFIG_PATA_RB532) += pata_rb532_cf.o
obj-$(CONFIG_PATA_RDC) += pata_rdc.o
-obj-$(CONFIG_PATA_RZ1000) += pata_rz1000.o
obj-$(CONFIG_PATA_SC1200) += pata_sc1200.o
+obj-$(CONFIG_PATA_SCC) += pata_scc.o
+obj-$(CONFIG_PATA_SCH) += pata_sch.o
obj-$(CONFIG_PATA_SERVERWORKS) += pata_serverworks.o
obj-$(CONFIG_PATA_SIL680) += pata_sil680.o
+obj-$(CONFIG_PATA_SIS) += pata_sis.o
obj-$(CONFIG_PATA_TOSHIBA) += pata_piccolo.o
+obj-$(CONFIG_PATA_TRIFLEX) += pata_triflex.o
obj-$(CONFIG_PATA_VIA) += pata_via.o
obj-$(CONFIG_PATA_WINBOND) += pata_sl82c105.o
-obj-$(CONFIG_PATA_WINBOND_VLB) += pata_winbond.o
-obj-$(CONFIG_PATA_SIS) += pata_sis.o
-obj-$(CONFIG_PATA_TRIFLEX) += pata_triflex.o
+
+# SFF PIO only
+obj-$(CONFIG_PATA_AT32) += pata_at32.o
+obj-$(CONFIG_PATA_AT91) += pata_at91.o
+obj-$(CONFIG_PATA_CMD640_PCI) += pata_cmd640.o
+obj-$(CONFIG_PATA_ISAPNP) += pata_isapnp.o
obj-$(CONFIG_PATA_IXP4XX_CF) += pata_ixp4xx_cf.o
-obj-$(CONFIG_PATA_SCC) += pata_scc.o
-obj-$(CONFIG_PATA_SCH) += pata_sch.o
-obj-$(CONFIG_PATA_BF54X) += pata_bf54x.o
-obj-$(CONFIG_PATA_OCTEON_CF) += pata_octeon_cf.o
+obj-$(CONFIG_PATA_MPIIX) += pata_mpiix.o
+obj-$(CONFIG_PATA_NS87410) += pata_ns87410.o
+obj-$(CONFIG_PATA_OPTI) += pata_opti.o
+obj-$(CONFIG_PATA_PCMCIA) += pata_pcmcia.o
+obj-$(CONFIG_PATA_PALMLD) += pata_palmld.o
obj-$(CONFIG_PATA_PLATFORM) += pata_platform.o
-obj-$(CONFIG_PATA_AT91) += pata_at91.o
obj-$(CONFIG_PATA_OF_PLATFORM) += pata_of_platform.o
-obj-$(CONFIG_PATA_ICSIDE) += pata_icside.o
+obj-$(CONFIG_PATA_QDI) += pata_qdi.o
+obj-$(CONFIG_PATA_RB532) += pata_rb532_cf.o
+obj-$(CONFIG_PATA_RZ1000) += pata_rz1000.o
+obj-$(CONFIG_PATA_WINBOND_VLB) += pata_winbond.o
+
# Should be last but two libata driver
obj-$(CONFIG_PATA_ACPI) += pata_acpi.o
# Should be last but one libata driver
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
index 33fb614..573158a 100644
--- a/drivers/ata/ata_generic.c
+++ b/drivers/ata/ata_generic.c
@@ -155,7 +155,7 @@ static int ata_generic_init_one(struct pci_dev *dev, const struct pci_device_id
return rc;
pcim_pin_device(dev);
}
- return ata_pci_sff_init_one(dev, ppi, &generic_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(dev, ppi, &generic_sht, NULL, 0);
}
static struct pci_device_id ata_generic[] = {
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index ec52fc6..7409f98 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -1589,7 +1589,7 @@ static int __devinit piix_init_one(struct pci_dev *pdev,
hpriv->map = piix_init_sata_map(pdev, port_info,
piix_map_db_table[ent->driver_data]);
- rc = ata_pci_sff_prepare_host(pdev, ppi, &host);
+ rc = ata_pci_bmdma_prepare_host(pdev, ppi, &host);
if (rc)
return rc;
host->private_data = hpriv;
@@ -1626,7 +1626,7 @@ static int __devinit piix_init_one(struct pci_dev *pdev,
host->flags |= ATA_HOST_PARALLEL_SCAN;
pci_set_master(pdev);
- return ata_pci_sff_activate_host(host, ata_sff_interrupt, &piix_sht);
+ return ata_pci_sff_activate_host(host, ata_bmdma_interrupt, &piix_sht);
}
static void piix_remove_one(struct pci_dev *pdev)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index c47373f..06b7e49 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -160,6 +160,10 @@ int libata_allow_tpm = 0;
module_param_named(allow_tpm, libata_allow_tpm, int, 0444);
MODULE_PARM_DESC(allow_tpm, "Permit the use of TPM commands (0=off [default], 1=on)");
+static int atapi_an;
+module_param(atapi_an, int, 0444);
+MODULE_PARM_DESC(atapi_an, "Enable ATAPI AN media presence notification (0=0ff [default], 1=on)");
+
MODULE_AUTHOR("Jeff Garzik");
MODULE_DESCRIPTION("Library module for ATA devices");
MODULE_LICENSE("GPL");
@@ -2122,6 +2126,14 @@ retry:
goto err_out;
}
+ if (dev->horkage & ATA_HORKAGE_DUMP_ID) {
+ ata_dev_printk(dev, KERN_DEBUG, "dumping IDENTIFY data, "
+ "class=%d may_fallback=%d tried_spinup=%d\n",
+ class, may_fallback, tried_spinup);
+ print_hex_dump(KERN_DEBUG, "", DUMP_PREFIX_OFFSET,
+ 16, 2, id, ATA_ID_WORDS * sizeof(*id), true);
+ }
+
/* Falling back doesn't make sense if ID data was read
* successfully at least once.
*/
@@ -2510,7 +2522,8 @@ int ata_dev_configure(struct ata_device *dev)
* to enable ATAPI AN to discern between PHY status
* changed notifications and ATAPI ANs.
*/
- if ((ap->flags & ATA_FLAG_AN) && ata_id_has_atapi_AN(id) &&
+ if (atapi_an &&
+ (ap->flags & ATA_FLAG_AN) && ata_id_has_atapi_AN(id) &&
(!sata_pmp_attached(ap) ||
sata_scr_read(&ap->link, SCR_NOTIFICATION, &sntf) == 0)) {
unsigned int err_mask;
@@ -6372,6 +6385,7 @@ static int __init ata_parse_force_one(char **cur,
{ "3.0Gbps", .spd_limit = 2 },
{ "noncq", .horkage_on = ATA_HORKAGE_NONCQ },
{ "ncq", .horkage_off = ATA_HORKAGE_NONCQ },
+ { "dump_id", .horkage_on = ATA_HORKAGE_DUMP_ID },
{ "pio0", .xfer_mask = 1 << (ATA_SHIFT_PIO + 0) },
{ "pio1", .xfer_mask = 1 << (ATA_SHIFT_PIO + 1) },
{ "pio2", .xfer_mask = 1 << (ATA_SHIFT_PIO + 2) },
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index 19ddf92..efa4a18 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -63,7 +63,6 @@ const struct ata_port_operations ata_sff_port_ops = {
.sff_tf_read = ata_sff_tf_read,
.sff_exec_command = ata_sff_exec_command,
.sff_data_xfer = ata_sff_data_xfer,
- .sff_irq_clear = ata_sff_irq_clear,
.sff_drain_fifo = ata_sff_drain_fifo,
.lost_interrupt = ata_sff_lost_interrupt,
@@ -395,33 +394,12 @@ void ata_sff_irq_on(struct ata_port *ap)
ata_sff_set_devctl(ap, ap->ctl);
ata_wait_idle(ap);
- ap->ops->sff_irq_clear(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
}
EXPORT_SYMBOL_GPL(ata_sff_irq_on);
/**
- * ata_sff_irq_clear - Clear PCI IDE BMDMA interrupt.
- * @ap: Port associated with this ATA transaction.
- *
- * Clear interrupt and error flags in DMA status register.
- *
- * May be used as the irq_clear() entry in ata_port_operations.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- */
-void ata_sff_irq_clear(struct ata_port *ap)
-{
- void __iomem *mmio = ap->ioaddr.bmdma_addr;
-
- if (!mmio)
- return;
-
- iowrite8(ioread8(mmio + ATA_DMA_STATUS), mmio + ATA_DMA_STATUS);
-}
-EXPORT_SYMBOL_GPL(ata_sff_irq_clear);
-
-/**
* ata_sff_tf_load - send taskfile registers to host controller
* @ap: Port to which output is sent
* @tf: ATA taskfile register set
@@ -820,11 +798,15 @@ static void atapi_send_cdb(struct ata_port *ap, struct ata_queued_cmd *qc)
case ATAPI_PROT_NODATA:
ap->hsm_task_state = HSM_ST_LAST;
break;
+#ifdef CONFIG_ATA_BMDMA
case ATAPI_PROT_DMA:
ap->hsm_task_state = HSM_ST_LAST;
/* initiate bmdma */
ap->ops->bmdma_start(qc);
break;
+#endif /* CONFIG_ATA_BMDMA */
+ default:
+ BUG();
}
}
@@ -1491,27 +1473,27 @@ bool ata_sff_qc_fill_rtf(struct ata_queued_cmd *qc)
}
EXPORT_SYMBOL_GPL(ata_sff_qc_fill_rtf);
-/**
- * ata_sff_host_intr - Handle host interrupt for given (port, task)
- * @ap: Port on which interrupt arrived (possibly...)
- * @qc: Taskfile currently active in engine
- *
- * Handle host interrupt for given queued command. Currently,
- * only DMA interrupts are handled. All other commands are
- * handled via polling with interrupts disabled (nIEN bit).
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- *
- * RETURNS:
- * One if interrupt was handled, zero if not (shared irq).
- */
-unsigned int ata_sff_host_intr(struct ata_port *ap,
- struct ata_queued_cmd *qc)
+static unsigned int ata_sff_idle_irq(struct ata_port *ap)
{
- struct ata_eh_info *ehi = &ap->link.eh_info;
- u8 status, host_stat = 0;
- bool bmdma_stopped = false;
+ ap->stats.idle_irq++;
+
+#ifdef ATA_IRQ_TRAP
+ if ((ap->stats.idle_irq % 1000) == 0) {
+ ap->ops->sff_check_status(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
+ ata_port_printk(ap, KERN_WARNING, "irq trap\n");
+ return 1;
+ }
+#endif
+ return 0; /* irq not handled */
+}
+
+static unsigned int __ata_sff_port_intr(struct ata_port *ap,
+ struct ata_queued_cmd *qc,
+ bool hsmv_on_idle)
+{
+ u8 status;
VPRINTK("ata%u: protocol %d task_state %d\n",
ap->print_id, qc->tf.protocol, ap->hsm_task_state);
@@ -1528,90 +1510,56 @@ unsigned int ata_sff_host_intr(struct ata_port *ap,
* need to check ata_is_atapi(qc->tf.protocol) again.
*/
if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
- goto idle_irq;
- break;
- case HSM_ST_LAST:
- if (qc->tf.protocol == ATA_PROT_DMA ||
- qc->tf.protocol == ATAPI_PROT_DMA) {
- /* check status of DMA engine */
- host_stat = ap->ops->bmdma_status(ap);
- VPRINTK("ata%u: host_stat 0x%X\n",
- ap->print_id, host_stat);
-
- /* if it's not our irq... */
- if (!(host_stat & ATA_DMA_INTR))
- goto idle_irq;
-
- /* before we do anything else, clear DMA-Start bit */
- ap->ops->bmdma_stop(qc);
- bmdma_stopped = true;
-
- if (unlikely(host_stat & ATA_DMA_ERR)) {
- /* error when transfering data to/from memory */
- qc->err_mask |= AC_ERR_HOST_BUS;
- ap->hsm_task_state = HSM_ST_ERR;
- }
- }
+ return ata_sff_idle_irq(ap);
break;
case HSM_ST:
+ case HSM_ST_LAST:
break;
default:
- goto idle_irq;
+ return ata_sff_idle_irq(ap);
}
-
/* check main status, clearing INTRQ if needed */
status = ata_sff_irq_status(ap);
if (status & ATA_BUSY) {
- if (bmdma_stopped) {
+ if (hsmv_on_idle) {
/* BMDMA engine is already stopped, we're screwed */
qc->err_mask |= AC_ERR_HSM;
ap->hsm_task_state = HSM_ST_ERR;
} else
- goto idle_irq;
+ return ata_sff_idle_irq(ap);
}
/* clear irq events */
- ap->ops->sff_irq_clear(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
ata_sff_hsm_move(ap, qc, status, 0);
- if (unlikely(qc->err_mask) && (qc->tf.protocol == ATA_PROT_DMA ||
- qc->tf.protocol == ATAPI_PROT_DMA))
- ata_ehi_push_desc(ehi, "BMDMA stat 0x%x", host_stat);
-
return 1; /* irq handled */
-
-idle_irq:
- ap->stats.idle_irq++;
-
-#ifdef ATA_IRQ_TRAP
- if ((ap->stats.idle_irq % 1000) == 0) {
- ap->ops->sff_check_status(ap);
- ap->ops->sff_irq_clear(ap);
- ata_port_printk(ap, KERN_WARNING, "irq trap\n");
- return 1;
- }
-#endif
- return 0; /* irq not handled */
}
-EXPORT_SYMBOL_GPL(ata_sff_host_intr);
/**
- * ata_sff_interrupt - Default ATA host interrupt handler
- * @irq: irq line (unused)
- * @dev_instance: pointer to our ata_host information structure
+ * ata_sff_port_intr - Handle SFF port interrupt
+ * @ap: Port on which interrupt arrived (possibly...)
+ * @qc: Taskfile currently active in engine
*
- * Default interrupt handler for PCI IDE devices. Calls
- * ata_sff_host_intr() for each port that is not disabled.
+ * Handle port interrupt for given queued command.
*
* LOCKING:
- * Obtains host lock during operation.
+ * spin_lock_irqsave(host lock)
*
* RETURNS:
- * IRQ_NONE or IRQ_HANDLED.
+ * One if interrupt was handled, zero if not (shared irq).
*/
-irqreturn_t ata_sff_interrupt(int irq, void *dev_instance)
+unsigned int ata_sff_port_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
+{
+ return __ata_sff_port_intr(ap, qc, false);
+}
+EXPORT_SYMBOL_GPL(ata_sff_port_intr);
+
+static inline irqreturn_t __ata_sff_interrupt(int irq, void *dev_instance,
+ unsigned int (*port_intr)(struct ata_port *, struct ata_queued_cmd *))
{
struct ata_host *host = dev_instance;
bool retried = false;
@@ -1631,7 +1579,7 @@ retry:
qc = ata_qc_from_tag(ap, ap->link.active_tag);
if (qc) {
if (!(qc->tf.flags & ATA_TFLAG_POLLING))
- handled |= ata_sff_host_intr(ap, qc);
+ handled |= port_intr(ap, qc);
else
polling |= 1 << i;
} else
@@ -1658,7 +1606,8 @@ retry:
if (idle & (1 << i)) {
ap->ops->sff_check_status(ap);
- ap->ops->sff_irq_clear(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
} else {
/* clear INTRQ and check if BUSY cleared */
if (!(ap->ops->sff_check_status(ap) & ATA_BUSY))
@@ -1680,6 +1629,25 @@ retry:
return IRQ_RETVAL(handled);
}
+
+/**
+ * ata_sff_interrupt - Default SFF ATA host interrupt handler
+ * @irq: irq line (unused)
+ * @dev_instance: pointer to our ata_host information structure
+ *
+ * Default interrupt handler for PCI IDE devices. Calls
+ * ata_sff_port_intr() for each port that is not disabled.
+ *
+ * LOCKING:
+ * Obtains host lock during operation.
+ *
+ * RETURNS:
+ * IRQ_NONE or IRQ_HANDLED.
+ */
+irqreturn_t ata_sff_interrupt(int irq, void *dev_instance)
+{
+ return __ata_sff_interrupt(irq, dev_instance, ata_sff_port_intr);
+}
EXPORT_SYMBOL_GPL(ata_sff_interrupt);
/**
@@ -1717,7 +1685,7 @@ void ata_sff_lost_interrupt(struct ata_port *ap)
status);
/* Run the host interrupt logic as if the interrupt had not been
lost */
- ata_sff_host_intr(ap, qc);
+ ata_sff_port_intr(ap, qc);
}
EXPORT_SYMBOL_GPL(ata_sff_lost_interrupt);
@@ -1744,7 +1712,8 @@ void ata_sff_freeze(struct ata_port *ap)
*/
ap->ops->sff_check_status(ap);
- ap->ops->sff_irq_clear(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
}
EXPORT_SYMBOL_GPL(ata_sff_freeze);
@@ -1761,7 +1730,8 @@ void ata_sff_thaw(struct ata_port *ap)
{
/* clear & re-enable interrupts */
ap->ops->sff_check_status(ap);
- ap->ops->sff_irq_clear(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
ata_sff_irq_on(ap);
}
EXPORT_SYMBOL_GPL(ata_sff_thaw);
@@ -2349,13 +2319,13 @@ int ata_pci_sff_init_host(struct ata_host *host)
EXPORT_SYMBOL_GPL(ata_pci_sff_init_host);
/**
- * ata_pci_sff_prepare_host - helper to prepare native PCI ATA host
+ * ata_pci_sff_prepare_host - helper to prepare PCI PIO-only SFF ATA host
* @pdev: target PCI device
* @ppi: array of port_info, must be enough for two ports
* @r_host: out argument for the initialized ATA host
*
- * Helper to allocate ATA host for @pdev, acquire all native PCI
- * resources and initialize it accordingly in one go.
+ * Helper to allocate PIO-only SFF ATA host for @pdev, acquire
+ * all PCI resources and initialize it accordingly in one go.
*
* LOCKING:
* Inherited from calling layer (may sleep).
@@ -2385,9 +2355,6 @@ int ata_pci_sff_prepare_host(struct pci_dev *pdev,
if (rc)
goto err_out;
- /* init DMA related stuff */
- ata_pci_bmdma_init(host);
-
devres_remove_group(&pdev->dev, NULL);
*r_host = host;
return 0;
@@ -2492,8 +2459,21 @@ out:
}
EXPORT_SYMBOL_GPL(ata_pci_sff_activate_host);
+static const struct ata_port_info *ata_sff_find_valid_pi(
+ const struct ata_port_info * const *ppi)
+{
+ int i;
+
+ /* look up the first valid port_info */
+ for (i = 0; i < 2 && ppi[i]; i++)
+ if (ppi[i]->port_ops != &ata_dummy_port_ops)
+ return ppi[i];
+
+ return NULL;
+}
+
/**
- * ata_pci_sff_init_one - Initialize/register PCI IDE host controller
+ * ata_pci_sff_init_one - Initialize/register PIO-only PCI IDE controller
* @pdev: Controller to be initialized
* @ppi: array of port_info, must be enough for two ports
* @sht: scsi_host_template to use when registering the host
@@ -2502,11 +2482,7 @@ EXPORT_SYMBOL_GPL(ata_pci_sff_activate_host);
*
* This is a helper function which can be called from a driver's
* xxx_init_one() probe function if the hardware uses traditional
- * IDE taskfile registers.
- *
- * This function calls pci_enable_device(), reserves its register
- * regions, sets the dma mask, enables bus master mode, and calls
- * ata_device_add()
+ * IDE taskfile registers and is PIO only.
*
* ASSUMPTION:
* Nobody makes a single channel controller that appears solely as
@@ -2523,20 +2499,13 @@ int ata_pci_sff_init_one(struct pci_dev *pdev,
struct scsi_host_template *sht, void *host_priv, int hflag)
{
struct device *dev = &pdev->dev;
- const struct ata_port_info *pi = NULL;
+ const struct ata_port_info *pi;
struct ata_host *host = NULL;
- int i, rc;
+ int rc;
DPRINTK("ENTER\n");
- /* look up the first valid port_info */
- for (i = 0; i < 2 && ppi[i]; i++) {
- if (ppi[i]->port_ops != &ata_dummy_port_ops) {
- pi = ppi[i];
- break;
- }
- }
-
+ pi = ata_sff_find_valid_pi(ppi);
if (!pi) {
dev_printk(KERN_ERR, &pdev->dev,
"no valid port_info specified\n");
@@ -2557,7 +2526,6 @@ int ata_pci_sff_init_one(struct pci_dev *pdev,
host->private_data = host_priv;
host->flags |= hflag;
- pci_set_master(pdev);
rc = ata_pci_sff_activate_host(host, ata_sff_interrupt, sht);
out:
if (rc == 0)
@@ -2571,6 +2539,12 @@ EXPORT_SYMBOL_GPL(ata_pci_sff_init_one);
#endif /* CONFIG_PCI */
+/*
+ * BMDMA support
+ */
+
+#ifdef CONFIG_ATA_BMDMA
+
const struct ata_port_operations ata_bmdma_port_ops = {
.inherits = &ata_sff_port_ops,
@@ -2580,6 +2554,7 @@ const struct ata_port_operations ata_bmdma_port_ops = {
.qc_prep = ata_bmdma_qc_prep,
.qc_issue = ata_bmdma_qc_issue,
+ .sff_irq_clear = ata_bmdma_irq_clear,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
@@ -2804,6 +2779,75 @@ unsigned int ata_bmdma_qc_issue(struct ata_queued_cmd *qc)
EXPORT_SYMBOL_GPL(ata_bmdma_qc_issue);
/**
+ * ata_bmdma_port_intr - Handle BMDMA port interrupt
+ * @ap: Port on which interrupt arrived (possibly...)
+ * @qc: Taskfile currently active in engine
+ *
+ * Handle port interrupt for given queued command.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ *
+ * RETURNS:
+ * One if interrupt was handled, zero if not (shared irq).
+ */
+unsigned int ata_bmdma_port_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
+{
+ struct ata_eh_info *ehi = &ap->link.eh_info;
+ u8 host_stat = 0;
+ bool bmdma_stopped = false;
+ unsigned int handled;
+
+ if (ap->hsm_task_state == HSM_ST_LAST && ata_is_dma(qc->tf.protocol)) {
+ /* check status of DMA engine */
+ host_stat = ap->ops->bmdma_status(ap);
+ VPRINTK("ata%u: host_stat 0x%X\n", ap->print_id, host_stat);
+
+ /* if it's not our irq... */
+ if (!(host_stat & ATA_DMA_INTR))
+ return ata_sff_idle_irq(ap);
+
+ /* before we do anything else, clear DMA-Start bit */
+ ap->ops->bmdma_stop(qc);
+ bmdma_stopped = true;
+
+ if (unlikely(host_stat & ATA_DMA_ERR)) {
+ /* error when transfering data to/from memory */
+ qc->err_mask |= AC_ERR_HOST_BUS;
+ ap->hsm_task_state = HSM_ST_ERR;
+ }
+ }
+
+ handled = __ata_sff_port_intr(ap, qc, bmdma_stopped);
+
+ if (unlikely(qc->err_mask) && ata_is_dma(qc->tf.protocol))
+ ata_ehi_push_desc(ehi, "BMDMA stat 0x%x", host_stat);
+
+ return handled;
+}
+EXPORT_SYMBOL_GPL(ata_bmdma_port_intr);
+
+/**
+ * ata_bmdma_interrupt - Default BMDMA ATA host interrupt handler
+ * @irq: irq line (unused)
+ * @dev_instance: pointer to our ata_host information structure
+ *
+ * Default interrupt handler for PCI IDE devices. Calls
+ * ata_bmdma_port_intr() for each port that is not disabled.
+ *
+ * LOCKING:
+ * Obtains host lock during operation.
+ *
+ * RETURNS:
+ * IRQ_NONE or IRQ_HANDLED.
+ */
+irqreturn_t ata_bmdma_interrupt(int irq, void *dev_instance)
+{
+ return __ata_sff_interrupt(irq, dev_instance, ata_bmdma_port_intr);
+}
+EXPORT_SYMBOL_GPL(ata_bmdma_interrupt);
+
+/**
* ata_bmdma_error_handler - Stock error handler for BMDMA controller
* @ap: port to handle error for
*
@@ -2848,7 +2892,8 @@ void ata_bmdma_error_handler(struct ata_port *ap)
/* if we're gonna thaw, make sure IRQ is clear */
if (thaw) {
ap->ops->sff_check_status(ap);
- ap->ops->sff_irq_clear(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
}
}
@@ -2882,6 +2927,28 @@ void ata_bmdma_post_internal_cmd(struct ata_queued_cmd *qc)
EXPORT_SYMBOL_GPL(ata_bmdma_post_internal_cmd);
/**
+ * ata_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt.
+ * @ap: Port associated with this ATA transaction.
+ *
+ * Clear interrupt and error flags in DMA status register.
+ *
+ * May be used as the irq_clear() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void ata_bmdma_irq_clear(struct ata_port *ap)
+{
+ void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+ if (!mmio)
+ return;
+
+ iowrite8(ioread8(mmio + ATA_DMA_STATUS), mmio + ATA_DMA_STATUS);
+}
+EXPORT_SYMBOL_GPL(ata_bmdma_irq_clear);
+
+/**
* ata_bmdma_setup - Set up PCI IDE BMDMA transaction
* @qc: Info associated with this ATA transaction.
*
@@ -3137,7 +3204,100 @@ void ata_pci_bmdma_init(struct ata_host *host)
}
EXPORT_SYMBOL_GPL(ata_pci_bmdma_init);
+/**
+ * ata_pci_bmdma_prepare_host - helper to prepare PCI BMDMA ATA host
+ * @pdev: target PCI device
+ * @ppi: array of port_info, must be enough for two ports
+ * @r_host: out argument for the initialized ATA host
+ *
+ * Helper to allocate BMDMA ATA host for @pdev, acquire all PCI
+ * resources and initialize it accordingly in one go.
+ *
+ * LOCKING:
+ * Inherited from calling layer (may sleep).
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
+ */
+int ata_pci_bmdma_prepare_host(struct pci_dev *pdev,
+ const struct ata_port_info * const * ppi,
+ struct ata_host **r_host)
+{
+ int rc;
+
+ rc = ata_pci_sff_prepare_host(pdev, ppi, r_host);
+ if (rc)
+ return rc;
+
+ ata_pci_bmdma_init(*r_host);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ata_pci_bmdma_prepare_host);
+
+/**
+ * ata_pci_bmdma_init_one - Initialize/register BMDMA PCI IDE controller
+ * @pdev: Controller to be initialized
+ * @ppi: array of port_info, must be enough for two ports
+ * @sht: scsi_host_template to use when registering the host
+ * @host_priv: host private_data
+ * @hflags: host flags
+ *
+ * This function is similar to ata_pci_sff_init_one() but also
+ * takes care of BMDMA initialization.
+ *
+ * LOCKING:
+ * Inherited from PCI layer (may sleep).
+ *
+ * RETURNS:
+ * Zero on success, negative on errno-based value on error.
+ */
+int ata_pci_bmdma_init_one(struct pci_dev *pdev,
+ const struct ata_port_info * const * ppi,
+ struct scsi_host_template *sht, void *host_priv,
+ int hflags)
+{
+ struct device *dev = &pdev->dev;
+ const struct ata_port_info *pi;
+ struct ata_host *host = NULL;
+ int rc;
+
+ DPRINTK("ENTER\n");
+
+ pi = ata_sff_find_valid_pi(ppi);
+ if (!pi) {
+ dev_printk(KERN_ERR, &pdev->dev,
+ "no valid port_info specified\n");
+ return -EINVAL;
+ }
+
+ if (!devres_open_group(dev, NULL, GFP_KERNEL))
+ return -ENOMEM;
+
+ rc = pcim_enable_device(pdev);
+ if (rc)
+ goto out;
+
+ /* prepare and activate BMDMA host */
+ rc = ata_pci_bmdma_prepare_host(pdev, ppi, &host);
+ if (rc)
+ goto out;
+ host->private_data = host_priv;
+ host->flags |= hflags;
+
+ pci_set_master(pdev);
+ rc = ata_pci_sff_activate_host(host, ata_bmdma_interrupt, sht);
+ out:
+ if (rc == 0)
+ devres_remove_group(&pdev->dev, NULL);
+ else
+ devres_release_group(&pdev->dev, NULL);
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(ata_pci_bmdma_init_one);
+
#endif /* CONFIG_PCI */
+#endif /* CONFIG_ATA_BMDMA */
/**
* ata_sff_port_init - Initialize SFF/BMDMA ATA port
diff --git a/drivers/ata/pata_acpi.c b/drivers/ata/pata_acpi.c
index 066b9f3..c8d4703 100644
--- a/drivers/ata/pata_acpi.c
+++ b/drivers/ata/pata_acpi.c
@@ -260,7 +260,7 @@ static int pacpi_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
return rc;
pcim_pin_device(pdev);
}
- return ata_pci_sff_init_one(pdev, ppi, &pacpi_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &pacpi_sht, NULL, 0);
}
static const struct pci_device_id pacpi_pci_tbl[] = {
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index f306e10..794ec6e 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -583,7 +583,10 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
ppi[0] = &info_20_udma;
}
- return ata_pci_sff_init_one(pdev, ppi, &ali_sht, NULL, 0);
+ if (!ppi[0]->mwdma_mask && !ppi[0]->udma_mask)
+ return ata_pci_sff_init_one(pdev, ppi, &ali_sht, NULL, 0);
+ else
+ return ata_pci_bmdma_init_one(pdev, ppi, &ali_sht, NULL, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index d95eca9..620a07c 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -574,7 +574,7 @@ static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
}
/* And fire it up */
- return ata_pci_sff_init_one(pdev, ppi, &amd_sht, hpriv, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &amd_sht, hpriv, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
index 4d066d6..ba43f0f 100644
--- a/drivers/ata/pata_artop.c
+++ b/drivers/ata/pata_artop.c
@@ -421,7 +421,7 @@ static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
BUG_ON(ppi[0] == NULL);
- return ata_pci_sff_init_one(pdev, ppi, &artop_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &artop_sht, NULL, 0);
}
static const struct pci_device_id artop_pci_tbl[] = {
diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
index 44d88b3..4375561 100644
--- a/drivers/ata/pata_atiixp.c
+++ b/drivers/ata/pata_atiixp.c
@@ -246,8 +246,8 @@ static int atiixp_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
if (!pci_test_config_bits(pdev, &atiixp_enable_bits[i]))
ppi[i] = &ata_dummy_port_info;
- return ata_pci_sff_init_one(pdev, ppi, &atiixp_sht, NULL,
- ATA_HOST_PARALLEL_SCAN);
+ return ata_pci_bmdma_init_one(pdev, ppi, &atiixp_sht, NULL,
+ ATA_HOST_PARALLEL_SCAN);
}
static const struct pci_device_id atiixp[] = {
diff --git a/drivers/ata/pata_atp867x.c b/drivers/ata/pata_atp867x.c
index bb6e074..9529593 100644
--- a/drivers/ata/pata_atp867x.c
+++ b/drivers/ata/pata_atp867x.c
@@ -525,7 +525,7 @@ static int atp867x_init_one(struct pci_dev *pdev,
pci_set_master(pdev);
- rc = ata_host_activate(host, pdev->irq, ata_sff_interrupt,
+ rc = ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
IRQF_SHARED, &atp867x_sht);
if (rc)
dev_printk(KERN_ERR, &pdev->dev, "failed to activate host\n");
diff --git a/drivers/ata/pata_bf54x.c b/drivers/ata/pata_bf54x.c
index 6422cfd..9cae65d 100644
--- a/drivers/ata/pata_bf54x.c
+++ b/drivers/ata/pata_bf54x.c
@@ -1214,7 +1214,7 @@ static unsigned int bfin_data_xfer(struct ata_device *dev, unsigned char *buf,
* bfin_irq_clear - Clear ATAPI interrupt.
* @ap: Port associated with this ATA transaction.
*
- * Note: Original code is ata_sff_irq_clear().
+ * Note: Original code is ata_bmdma_irq_clear().
*/
static void bfin_irq_clear(struct ata_port *ap)
diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c
index 4c81a71..9f5da1c 100644
--- a/drivers/ata/pata_cmd64x.c
+++ b/drivers/ata/pata_cmd64x.c
@@ -367,7 +367,7 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
pci_write_config_byte(pdev, UDIDETCR0, 0xF0);
#endif
- return ata_pci_sff_init_one(pdev, ppi, &cmd64x_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &cmd64x_sht, NULL, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c
index 17c5f34..030952f 100644
--- a/drivers/ata/pata_cs5520.c
+++ b/drivers/ata/pata_cs5520.c
@@ -221,7 +221,7 @@ static int __devinit cs5520_init_one(struct pci_dev *pdev, const struct pci_devi
continue;
rc = devm_request_irq(&pdev->dev, irq[ap->port_no],
- ata_sff_interrupt, 0, DRV_NAME, host);
+ ata_bmdma_interrupt, 0, DRV_NAME, host);
if (rc)
return rc;
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
index e809a42..f792330 100644
--- a/drivers/ata/pata_cs5530.c
+++ b/drivers/ata/pata_cs5530.c
@@ -324,7 +324,7 @@ static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
ppi[1] = &info_palmax_secondary;
/* Now kick off ATA set up */
- return ata_pci_sff_init_one(pdev, ppi, &cs5530_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &cs5530_sht, NULL, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_cs5535.c b/drivers/ata/pata_cs5535.c
index a02e645..03a9318 100644
--- a/drivers/ata/pata_cs5535.c
+++ b/drivers/ata/pata_cs5535.c
@@ -198,7 +198,7 @@ static int cs5535_init_one(struct pci_dev *dev, const struct pci_device_id *id)
rdmsr(ATAC_CH0D1_PIO, timings, dummy);
if (CS5535_BAD_PIO(timings))
wrmsr(ATAC_CH0D1_PIO, 0xF7F4F7F4UL, 0);
- return ata_pci_sff_init_one(dev, ppi, &cs5535_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(dev, ppi, &cs5535_sht, NULL, 0);
}
static const struct pci_device_id cs5535[] = {
diff --git a/drivers/ata/pata_cs5536.c b/drivers/ata/pata_cs5536.c
index 914ae35..21ee23f 100644
--- a/drivers/ata/pata_cs5536.c
+++ b/drivers/ata/pata_cs5536.c
@@ -260,7 +260,7 @@ static int cs5536_init_one(struct pci_dev *dev, const struct pci_device_id *id)
return -ENODEV;
}
- return ata_pci_sff_init_one(dev, ppi, &cs5536_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(dev, ppi, &cs5536_sht, NULL, 0);
}
static const struct pci_device_id cs5536[] = {
diff --git a/drivers/ata/pata_cypress.c b/drivers/ata/pata_cypress.c
index 0fcc096..6d915b0 100644
--- a/drivers/ata/pata_cypress.c
+++ b/drivers/ata/pata_cypress.c
@@ -138,7 +138,7 @@ static int cy82c693_init_one(struct pci_dev *pdev, const struct pci_device_id *i
if (PCI_FUNC(pdev->devfn) != 1)
return -ENODEV;
- return ata_pci_sff_init_one(pdev, ppi, &cy82c693_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &cy82c693_sht, NULL, 0);
}
static const struct pci_device_id cy82c693[] = {
diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c
index 3bac0e0..a088347 100644
--- a/drivers/ata/pata_efar.c
+++ b/drivers/ata/pata_efar.c
@@ -277,8 +277,8 @@ static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
- return ata_pci_sff_init_one(pdev, ppi, &efar_sht, NULL,
- ATA_HOST_PARALLEL_SCAN);
+ return ata_pci_bmdma_init_one(pdev, ppi, &efar_sht, NULL,
+ ATA_HOST_PARALLEL_SCAN);
}
static const struct pci_device_id efar_pci_tbl[] = {
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index 8580eb3..7688868 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -361,7 +361,7 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
break;
}
/* Now kick off ATA set up */
- return ata_pci_sff_init_one(dev, ppi, &hpt36x_sht, hpriv, 0);
+ return ata_pci_bmdma_init_one(dev, ppi, &hpt36x_sht, hpriv, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index 98b498b..9ae4c08 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -987,7 +987,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
}
/* Now kick off ATA set up */
- return ata_pci_sff_init_one(dev, ppi, &hpt37x_sht, private_data, 0);
+ return ata_pci_bmdma_init_one(dev, ppi, &hpt37x_sht, private_data, 0);
}
static const struct pci_device_id hpt37x[] = {
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index 8b95aeb..32f3463 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -548,7 +548,7 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
/* Now kick off ATA set up */
- return ata_pci_sff_init_one(dev, ppi, &hpt3x2n_sht, hpriv, 0);
+ return ata_pci_bmdma_init_one(dev, ppi, &hpt3x2n_sht, hpriv, 0);
}
static const struct pci_device_id hpt3x2n[] = {
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
index 727a81c..b63d5e2 100644
--- a/drivers/ata/pata_hpt3x3.c
+++ b/drivers/ata/pata_hpt3x3.c
@@ -248,7 +248,7 @@ static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
ata_port_pbar_desc(ap, 4, offset_cmd[i], "cmd");
}
pci_set_master(pdev);
- return ata_host_activate(host, pdev->irq, ata_sff_interrupt,
+ return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
IRQF_SHARED, &hpt3x3_sht);
}
diff --git a/drivers/ata/pata_icside.c b/drivers/ata/pata_icside.c
index b56e8f7..9f2889f 100644
--- a/drivers/ata/pata_icside.c
+++ b/drivers/ata/pata_icside.c
@@ -470,7 +470,7 @@ static int __devinit pata_icside_add_ports(struct pata_icside_info *info)
pata_icside_setup_ioaddr(ap, info->base, info, info->port[i]);
}
- return ata_host_activate(host, ec->irq, ata_sff_interrupt, 0,
+ return ata_host_activate(host, ec->irq, ata_bmdma_interrupt, 0,
&pata_icside_sht);
}
diff --git a/drivers/ata/pata_it8213.c b/drivers/ata/pata_it8213.c
index f971f0d..4d142a2 100644
--- a/drivers/ata/pata_it8213.c
+++ b/drivers/ata/pata_it8213.c
@@ -273,7 +273,7 @@ static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *en
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
- return ata_pci_sff_init_one(pdev, ppi, &it8213_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &it8213_sht, NULL, 0);
}
static const struct pci_device_id it8213_pci_tbl[] = {
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
index 2bd2b00..bf88f71 100644
--- a/drivers/ata/pata_it821x.c
+++ b/drivers/ata/pata_it821x.c
@@ -933,7 +933,7 @@ static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
else
ppi[0] = &info_smart;
}
- return ata_pci_sff_init_one(pdev, ppi, &it821x_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &it821x_sht, NULL, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
index 565e01e..cb3babb 100644
--- a/drivers/ata/pata_jmicron.c
+++ b/drivers/ata/pata_jmicron.c
@@ -144,7 +144,7 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i
};
const struct ata_port_info *ppi[] = { &info, NULL };
- return ata_pci_sff_init_one(pdev, ppi, &jmicron_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &jmicron_sht, NULL, 0);
}
static const struct pci_device_id jmicron_pci_tbl[] = {
diff --git a/drivers/ata/pata_macio.c b/drivers/ata/pata_macio.c
index b5b48e7..76640ac 100644
--- a/drivers/ata/pata_macio.c
+++ b/drivers/ata/pata_macio.c
@@ -1110,7 +1110,7 @@ static int __devinit pata_macio_common_init(struct pata_macio_priv *priv,
/* Start it up */
priv->irq = irq;
- return ata_host_activate(priv->host, irq, ata_sff_interrupt, 0,
+ return ata_host_activate(priv->host, irq, ata_bmdma_interrupt, 0,
&pata_macio_sht);
}
diff --git a/drivers/ata/pata_marvell.c b/drivers/ata/pata_marvell.c
index e8ca02e..dd38083 100644
--- a/drivers/ata/pata_marvell.c
+++ b/drivers/ata/pata_marvell.c
@@ -153,7 +153,7 @@ static int marvell_init_one (struct pci_dev *pdev, const struct pci_device_id *i
return -ENODEV;
}
#endif
- return ata_pci_sff_init_one(pdev, ppi, &marvell_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &marvell_sht, NULL, 0);
}
static const struct pci_device_id marvell_pci_tbl[] = {
diff --git a/drivers/ata/pata_mpc52xx.c b/drivers/ata/pata_mpc52xx.c
index 36afe2c..f087ab5 100644
--- a/drivers/ata/pata_mpc52xx.c
+++ b/drivers/ata/pata_mpc52xx.c
@@ -659,7 +659,7 @@ mpc52xx_ata_init_one(struct device *dev, struct mpc52xx_ata_priv *priv,
ata_port_desc(ap, "ata_regs 0x%lx", raw_ata_regs);
/* activate host */
- return ata_host_activate(host, priv->ata_irq, ata_sff_interrupt, 0,
+ return ata_host_activate(host, priv->ata_irq, ata_bmdma_interrupt, 0,
&mpc52xx_ata_sht);
}
diff --git a/drivers/ata/pata_netcell.c b/drivers/ata/pata_netcell.c
index 94f979a..3eb921c 100644
--- a/drivers/ata/pata_netcell.c
+++ b/drivers/ata/pata_netcell.c
@@ -82,7 +82,7 @@ static int netcell_init_one (struct pci_dev *pdev, const struct pci_device_id *e
ata_pci_bmdma_clear_simplex(pdev);
/* And let the library code do the work */
- return ata_pci_sff_init_one(pdev, port_info, &netcell_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, port_info, &netcell_sht, NULL, 0);
}
static const struct pci_device_id netcell_pci_tbl[] = {
diff --git a/drivers/ata/pata_ninja32.c b/drivers/ata/pata_ninja32.c
index dd53a66..cc50bd0 100644
--- a/drivers/ata/pata_ninja32.c
+++ b/drivers/ata/pata_ninja32.c
@@ -149,7 +149,7 @@ static int ninja32_init_one(struct pci_dev *dev, const struct pci_device_id *id)
ninja32_program(base);
/* FIXME: Should we disable them at remove ? */
- return ata_host_activate(host, dev->irq, ata_sff_interrupt,
+ return ata_host_activate(host, dev->irq, ata_bmdma_interrupt,
IRQF_SHARED, &ninja32_sht);
}
diff --git a/drivers/ata/pata_ns87415.c b/drivers/ata/pata_ns87415.c
index fdbba2d..605f198 100644
--- a/drivers/ata/pata_ns87415.c
+++ b/drivers/ata/pata_ns87415.c
@@ -380,7 +380,7 @@ static int ns87415_init_one (struct pci_dev *pdev, const struct pci_device_id *e
ns87415_fixup(pdev);
- return ata_pci_sff_init_one(pdev, ppi, &ns87415_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &ns87415_sht, NULL, 0);
}
static const struct pci_device_id ns87415_pci_tbl[] = {
diff --git a/drivers/ata/pata_octeon_cf.c b/drivers/ata/pata_octeon_cf.c
index 3001109..06ddd91 100644
--- a/drivers/ata/pata_octeon_cf.c
+++ b/drivers/ata/pata_octeon_cf.c
@@ -750,20 +750,6 @@ static void octeon_cf_dev_config(struct ata_device *dev)
}
/*
- * Trap if driver tries to do standard bmdma commands. They are not
- * supported.
- */
-static void unreachable_qc(struct ata_queued_cmd *qc)
-{
- BUG();
-}
-
-static u8 unreachable_port(struct ata_port *ap)
-{
- BUG();
-}
-
-/*
* We don't do ATAPI DMA so return 0.
*/
static int octeon_cf_check_atapi_dma(struct ata_queued_cmd *qc)
@@ -804,10 +790,6 @@ static struct ata_port_operations octeon_cf_ops = {
.sff_dev_select = octeon_cf_dev_select,
.sff_irq_on = octeon_cf_irq_on,
.sff_irq_clear = octeon_cf_irq_clear,
- .bmdma_setup = unreachable_qc,
- .bmdma_start = unreachable_qc,
- .bmdma_stop = unreachable_qc,
- .bmdma_status = unreachable_port,
.cable_detect = ata_cable_40wire,
.set_piomode = octeon_cf_set_piomode,
.set_dmamode = octeon_cf_set_dmamode,
diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c
index 988ef26..b811c16 100644
--- a/drivers/ata/pata_oldpiix.c
+++ b/drivers/ata/pata_oldpiix.c
@@ -248,7 +248,7 @@ static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *e
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
- return ata_pci_sff_init_one(pdev, ppi, &oldpiix_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &oldpiix_sht, NULL, 0);
}
static const struct pci_device_id oldpiix_pci_tbl[] = {
diff --git a/drivers/ata/pata_optidma.c b/drivers/ata/pata_optidma.c
index 76b7d12..0852cd0 100644
--- a/drivers/ata/pata_optidma.c
+++ b/drivers/ata/pata_optidma.c
@@ -429,7 +429,7 @@ static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id)
if (optiplus_with_udma(dev))
ppi[0] = &info_82c700_udma;
- return ata_pci_sff_init_one(dev, ppi, &optidma_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(dev, ppi, &optidma_sht, NULL, 0);
}
static const struct pci_device_id optidma[] = {
diff --git a/drivers/ata/pata_pdc2027x.c b/drivers/ata/pata_pdc2027x.c
index 09f1f22..b183511 100644
--- a/drivers/ata/pata_pdc2027x.c
+++ b/drivers/ata/pata_pdc2027x.c
@@ -754,7 +754,7 @@ static int __devinit pdc2027x_init_one(struct pci_dev *pdev, const struct pci_de
return -EIO;
pci_set_master(pdev);
- return ata_host_activate(host, pdev->irq, ata_sff_interrupt,
+ return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
IRQF_SHARED, &pdc2027x_sht);
}
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c
index fa1e2f3..c39f213 100644
--- a/drivers/ata/pata_pdc202xx_old.c
+++ b/drivers/ata/pata_pdc202xx_old.c
@@ -337,7 +337,7 @@ static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id
return -ENODEV;
}
}
- return ata_pci_sff_init_one(dev, ppi, &pdc202xx_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(dev, ppi, &pdc202xx_sht, NULL, 0);
}
static const struct pci_device_id pdc202xx[] = {
diff --git a/drivers/ata/pata_piccolo.c b/drivers/ata/pata_piccolo.c
index 9816154..cb01bf9 100644
--- a/drivers/ata/pata_piccolo.c
+++ b/drivers/ata/pata_piccolo.c
@@ -95,7 +95,7 @@ static int ata_tosh_init_one(struct pci_dev *dev, const struct pci_device_id *id
};
const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
/* Just one port for the moment */
- return ata_pci_sff_init_one(dev, ppi, &tosh_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(dev, ppi, &tosh_sht, NULL, 0);
}
static struct pci_device_id ata_tosh[] = {
diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c
index a5fa388..8574b31 100644
--- a/drivers/ata/pata_radisys.c
+++ b/drivers/ata/pata_radisys.c
@@ -227,7 +227,7 @@ static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *e
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
- return ata_pci_sff_init_one(pdev, ppi, &radisys_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &radisys_sht, NULL, 0);
}
static const struct pci_device_id radisys_pci_tbl[] = {
diff --git a/drivers/ata/pata_rdc.c b/drivers/ata/pata_rdc.c
index 37092cf..5fbe9b1 100644
--- a/drivers/ata/pata_rdc.c
+++ b/drivers/ata/pata_rdc.c
@@ -344,7 +344,7 @@ static int __devinit rdc_init_one(struct pci_dev *pdev,
*/
pci_read_config_dword(pdev, 0x54, &hpriv->saved_iocfg);
- rc = ata_pci_sff_prepare_host(pdev, ppi, &host);
+ rc = ata_pci_bmdma_prepare_host(pdev, ppi, &host);
if (rc)
return rc;
host->private_data = hpriv;
@@ -354,7 +354,7 @@ static int __devinit rdc_init_one(struct pci_dev *pdev,
host->flags |= ATA_HOST_PARALLEL_SCAN;
pci_set_master(pdev);
- return ata_pci_sff_activate_host(host, ata_sff_interrupt, &rdc_sht);
+ return ata_pci_sff_activate_host(host, ata_bmdma_interrupt, &rdc_sht);
}
static void rdc_remove_one(struct pci_dev *pdev)
diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c
index 6b5b63a..e2c1825 100644
--- a/drivers/ata/pata_sc1200.c
+++ b/drivers/ata/pata_sc1200.c
@@ -237,7 +237,7 @@ static int sc1200_init_one(struct pci_dev *dev, const struct pci_device_id *id)
};
const struct ata_port_info *ppi[] = { &info, NULL };
- return ata_pci_sff_init_one(dev, ppi, &sc1200_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(dev, ppi, &sc1200_sht, NULL, 0);
}
static const struct pci_device_id sc1200[] = {
diff --git a/drivers/ata/pata_scc.c b/drivers/ata/pata_scc.c
index 6f6193b..d9db3f8 100644
--- a/drivers/ata/pata_scc.c
+++ b/drivers/ata/pata_scc.c
@@ -875,7 +875,7 @@ static void scc_postreset(struct ata_link *link, unsigned int *classes)
* scc_irq_clear - Clear PCI IDE BMDMA interrupt.
* @ap: Port associated with this ATA transaction.
*
- * Note: Original code is ata_sff_irq_clear().
+ * Note: Original code is ata_bmdma_irq_clear().
*/
static void scc_irq_clear (struct ata_port *ap)
@@ -1105,7 +1105,7 @@ static int scc_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
if (rc)
return rc;
- return ata_host_activate(host, pdev->irq, ata_sff_interrupt,
+ return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
IRQF_SHARED, &scc_sht);
}
diff --git a/drivers/ata/pata_sch.c b/drivers/ata/pata_sch.c
index 86b3d01..e97b32f 100644
--- a/drivers/ata/pata_sch.c
+++ b/drivers/ata/pata_sch.c
@@ -179,7 +179,7 @@ static int __devinit sch_init_one(struct pci_dev *pdev,
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
- return ata_pci_sff_init_one(pdev, ppi, &sch_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &sch_sht, NULL, 0);
}
static int __init sch_init(void)
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c
index 43ea389..86dd714 100644
--- a/drivers/ata/pata_serverworks.c
+++ b/drivers/ata/pata_serverworks.c
@@ -460,7 +460,7 @@ static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id
if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
ata_pci_bmdma_clear_simplex(pdev);
- return ata_pci_sff_init_one(pdev, ppi, &serverworks_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &serverworks_sht, NULL, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index 43faf10..d3190d7 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -374,11 +374,11 @@ static int __devinit sil680_init_one(struct pci_dev *pdev,
ata_sff_std_ports(&host->ports[1]->ioaddr);
/* Register & activate */
- return ata_host_activate(host, pdev->irq, ata_sff_interrupt,
+ return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
IRQF_SHARED, &sil680_sht);
use_ioports:
- return ata_pci_sff_init_one(pdev, ppi, &sil680_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &sil680_sht, NULL, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index b670803..60cea13 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -826,7 +826,7 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
sis_fixup(pdev, chipset);
- return ata_pci_sff_init_one(pdev, ppi, &sis_sht, chipset, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &sis_sht, chipset, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index 733b042..98548f6 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -316,7 +316,7 @@ static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id
val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
pci_write_config_dword(dev, 0x40, val);
- return ata_pci_sff_init_one(dev, ppi, &sl82c105_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(dev, ppi, &sl82c105_sht, NULL, 0);
}
static const struct pci_device_id sl82c105[] = {
diff --git a/drivers/ata/pata_triflex.c b/drivers/ata/pata_triflex.c
index 48f5060..0d1f89e 100644
--- a/drivers/ata/pata_triflex.c
+++ b/drivers/ata/pata_triflex.c
@@ -201,7 +201,7 @@ static int triflex_init_one(struct pci_dev *dev, const struct pci_device_id *id)
if (!printed_version++)
dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
- return ata_pci_sff_init_one(dev, ppi, &triflex_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(dev, ppi, &triflex_sht, NULL, 0);
}
static const struct pci_device_id triflex[] = {
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 7e3e0a5..5e65988 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -627,7 +627,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
}
/* We have established the device type, now fire it up */
- return ata_pci_sff_init_one(pdev, ppi, &via_sht, (void *)config, 0);
+ return ata_pci_bmdma_init_one(pdev, ppi, &via_sht, (void *)config, 0);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index f3471bc..a476cd9 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -675,8 +675,6 @@ static struct ata_port_operations mv5_ops = {
.freeze = mv_eh_freeze,
.thaw = mv_eh_thaw,
.hardreset = mv_hardreset,
- .error_handler = ata_std_error_handler, /* avoid SFF EH */
- .post_internal_cmd = ATA_OP_NULL,
.scr_read = mv5_scr_read,
.scr_write = mv5_scr_write,
@@ -2813,7 +2811,7 @@ static void mv_port_intr(struct ata_port *ap, u32 port_cause)
} else if (!edma_was_enabled) {
struct ata_queued_cmd *qc = mv_get_active_qc(ap);
if (qc)
- ata_sff_host_intr(ap, qc);
+ ata_bmdma_port_intr(ap, qc);
else
mv_unexpected_intr(ap, edma_was_enabled);
}
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index baa8f0d..6fd1147 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -920,7 +920,7 @@ static int nv_host_intr(struct ata_port *ap, u8 irq_stat)
}
/* handle interrupt */
- return ata_sff_host_intr(ap, qc);
+ return ata_bmdma_port_intr(ap, qc);
}
static irqreturn_t nv_adma_interrupt(int irq, void *dev_instance)
@@ -1100,7 +1100,7 @@ static void nv_adma_irq_clear(struct ata_port *ap)
u32 notifier_clears[2];
if (pp->flags & NV_ADMA_ATAPI_SETUP_COMPLETE) {
- ata_sff_irq_clear(ap);
+ ata_bmdma_irq_clear(ap);
return;
}
@@ -1505,7 +1505,7 @@ static irqreturn_t nv_generic_interrupt(int irq, void *dev_instance)
qc = ata_qc_from_tag(ap, ap->link.active_tag);
if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING))) {
- handled += ata_sff_host_intr(ap, qc);
+ handled += ata_bmdma_port_intr(ap, qc);
} else {
/*
* No request pending? Clear interrupt status
@@ -2430,7 +2430,7 @@ static int nv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
ppi[0] = &nv_port_info[type];
ipriv = ppi[0]->private_data;
- rc = ata_pci_sff_prepare_host(pdev, ppi, &host);
+ rc = ata_pci_bmdma_prepare_host(pdev, ppi, &host);
if (rc)
return rc;
diff --git a/drivers/ata/sata_qstor.c b/drivers/ata/sata_qstor.c
index d533b3d..daeebf1 100644
--- a/drivers/ata/sata_qstor.c
+++ b/drivers/ata/sata_qstor.c
@@ -120,8 +120,6 @@ static void qs_host_stop(struct ata_host *host);
static void qs_qc_prep(struct ata_queued_cmd *qc);
static unsigned int qs_qc_issue(struct ata_queued_cmd *qc);
static int qs_check_atapi_dma(struct ata_queued_cmd *qc);
-static void qs_bmdma_stop(struct ata_queued_cmd *qc);
-static u8 qs_bmdma_status(struct ata_port *ap);
static void qs_freeze(struct ata_port *ap);
static void qs_thaw(struct ata_port *ap);
static int qs_prereset(struct ata_link *link, unsigned long deadline);
@@ -137,8 +135,6 @@ static struct ata_port_operations qs_ata_ops = {
.inherits = &ata_sff_port_ops,
.check_atapi_dma = qs_check_atapi_dma,
- .bmdma_stop = qs_bmdma_stop,
- .bmdma_status = qs_bmdma_status,
.qc_prep = qs_qc_prep,
.qc_issue = qs_qc_issue,
@@ -190,16 +186,6 @@ static int qs_check_atapi_dma(struct ata_queued_cmd *qc)
return 1; /* ATAPI DMA not supported */
}
-static void qs_bmdma_stop(struct ata_queued_cmd *qc)
-{
- /* nothing */
-}
-
-static u8 qs_bmdma_status(struct ata_port *ap)
-{
- return 0;
-}
-
static inline void qs_enter_reg_mode(struct ata_port *ap)
{
u8 __iomem *chan = qs_mmio_base(ap->host) + (ap->port_no * 0x4000);
@@ -454,7 +440,7 @@ static inline unsigned int qs_intr_mmio(struct ata_host *host)
if (!pp || pp->state != qs_state_mmio)
continue;
if (!(qc->tf.flags & ATA_TFLAG_POLLING))
- handled |= ata_sff_host_intr(ap, qc);
+ handled |= ata_sff_port_intr(ap, qc);
}
return handled;
}
diff --git a/drivers/ata/sata_sil.c b/drivers/ata/sata_sil.c
index 2dda312..3a4f842 100644
--- a/drivers/ata/sata_sil.c
+++ b/drivers/ata/sata_sil.c
@@ -503,7 +503,7 @@ static void sil_host_intr(struct ata_port *ap, u32 bmdma2)
goto err_hsm;
/* ack bmdma irq events */
- ata_sff_irq_clear(ap);
+ ata_bmdma_irq_clear(ap);
/* kick HSM in the ass */
ata_sff_hsm_move(ap, qc, status, 0);
@@ -584,7 +584,7 @@ static void sil_thaw(struct ata_port *ap)
/* clear IRQ */
ap->ops->sff_check_status(ap);
- ata_sff_irq_clear(ap);
+ ata_bmdma_irq_clear(ap);
/* turn on SATA IRQ if supported */
if (!(ap->flags & SIL_FLAG_NO_SATA_IRQ))
diff --git a/drivers/ata/sata_sis.c b/drivers/ata/sata_sis.c
index f8a91bf..2bfe3ae 100644
--- a/drivers/ata/sata_sis.c
+++ b/drivers/ata/sata_sis.c
@@ -279,7 +279,7 @@ static int sis_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
break;
}
- rc = ata_pci_sff_prepare_host(pdev, ppi, &host);
+ rc = ata_pci_bmdma_prepare_host(pdev, ppi, &host);
if (rc)
return rc;
@@ -308,7 +308,7 @@ static int sis_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
pci_set_master(pdev);
pci_intx(pdev, 1);
- return ata_host_activate(host, pdev->irq, ata_sff_interrupt,
+ return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
IRQF_SHARED, &sis_sht);
}
diff --git a/drivers/ata/sata_svw.c b/drivers/ata/sata_svw.c
index 101fd6a..7d9db4a 100644
--- a/drivers/ata/sata_svw.c
+++ b/drivers/ata/sata_svw.c
@@ -502,7 +502,7 @@ static int k2_sata_init_one(struct pci_dev *pdev, const struct pci_device_id *en
writel(0x0, mmio_base + K2_SATA_SIM_OFFSET);
pci_set_master(pdev);
- return ata_host_activate(host, pdev->irq, ata_sff_interrupt,
+ return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
IRQF_SHARED, &k2_sata_sht);
}
diff --git a/drivers/ata/sata_uli.c b/drivers/ata/sata_uli.c
index d8dac17..b8578c3 100644
--- a/drivers/ata/sata_uli.c
+++ b/drivers/ata/sata_uli.c
@@ -242,7 +242,7 @@ static int uli_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
pci_set_master(pdev);
pci_intx(pdev, 1);
- return ata_host_activate(host, pdev->irq, ata_sff_interrupt,
+ return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
IRQF_SHARED, &uli_sht);
}
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index 08f6549..101d8c2 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -308,7 +308,7 @@ static void svia_noop_freeze(struct ata_port *ap)
* certain way. Leave it alone and just clear pending IRQ.
*/
ap->ops->sff_check_status(ap);
- ata_sff_irq_clear(ap);
+ ata_bmdma_irq_clear(ap);
}
/**
@@ -463,7 +463,7 @@ static int vt6420_prepare_host(struct pci_dev *pdev, struct ata_host **r_host)
struct ata_host *host;
int rc;
- rc = ata_pci_sff_prepare_host(pdev, ppi, &host);
+ rc = ata_pci_bmdma_prepare_host(pdev, ppi, &host);
if (rc)
return rc;
*r_host = host;
@@ -520,7 +520,7 @@ static int vt8251_prepare_host(struct pci_dev *pdev, struct ata_host **r_host)
struct ata_host *host;
int i, rc;
- rc = ata_pci_sff_prepare_host(pdev, ppi, &host);
+ rc = ata_pci_bmdma_prepare_host(pdev, ppi, &host);
if (rc)
return rc;
*r_host = host;
@@ -628,7 +628,7 @@ static int svia_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
svia_configure(pdev);
pci_set_master(pdev);
- return ata_host_activate(host, pdev->irq, ata_sff_interrupt,
+ return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
IRQF_SHARED, &svia_sht);
}
diff --git a/drivers/ata/sata_vsc.c b/drivers/ata/sata_vsc.c
index 2107952..b777176 100644
--- a/drivers/ata/sata_vsc.c
+++ b/drivers/ata/sata_vsc.c
@@ -245,7 +245,7 @@ static void vsc_port_intr(u8 port_status, struct ata_port *ap)
qc = ata_qc_from_tag(ap, ap->link.active_tag);
if (qc && likely(!(qc->tf.flags & ATA_TFLAG_POLLING)))
- handled = ata_sff_host_intr(ap, qc);
+ handled = ata_bmdma_port_intr(ap, qc);
/* We received an interrupt during a polled command,
* or some other spurious condition. Interrupt reporting
diff --git a/include/linux/libata.h b/include/linux/libata.h
index ee84e7e..3bad270 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -386,6 +386,7 @@ enum {
ATA_HORKAGE_1_5_GBPS = (1 << 13), /* force 1.5 Gbps */
ATA_HORKAGE_NOSETXFER = (1 << 14), /* skip SETXFER, SATA only */
ATA_HORKAGE_BROKEN_FPDMA_AA = (1 << 15), /* skip AA */
+ ATA_HORKAGE_DUMP_ID = (1 << 16), /* dump IDENTIFY data */
/* DMA mask for user DMA control: User visible values; DO NOT
renumber */
@@ -513,7 +514,9 @@ struct ata_ioports {
void __iomem *command_addr;
void __iomem *altstatus_addr;
void __iomem *ctl_addr;
+#ifdef CONFIG_ATA_BMDMA
void __iomem *bmdma_addr;
+#endif /* CONFIG_ATA_BMDMA */
void __iomem *scr_addr;
};
#endif /* CONFIG_ATA_SFF */
@@ -721,8 +724,10 @@ struct ata_port {
u8 ctl; /* cache of ATA control register */
u8 last_ctl; /* Cache last written value */
struct delayed_work sff_pio_task;
+#ifdef CONFIG_ATA_BMDMA
struct ata_bmdma_prd *bmdma_prd; /* BMDMA SG list */
dma_addr_t bmdma_prd_dma; /* and its DMA mapping */
+#endif /* CONFIG_ATA_BMDMA */
#endif /* CONFIG_ATA_SFF */
unsigned int pio_mask;
@@ -856,10 +861,12 @@ struct ata_port_operations {
void (*sff_irq_clear)(struct ata_port *);
void (*sff_drain_fifo)(struct ata_queued_cmd *qc);
+#ifdef CONFIG_ATA_BMDMA
void (*bmdma_setup)(struct ata_queued_cmd *qc);
void (*bmdma_start)(struct ata_queued_cmd *qc);
void (*bmdma_stop)(struct ata_queued_cmd *qc);
u8 (*bmdma_status)(struct ata_port *ap);
+#endif /* CONFIG_ATA_BMDMA */
#endif /* CONFIG_ATA_SFF */
ssize_t (*em_show)(struct ata_port *ap, char *buf);
@@ -1555,7 +1562,6 @@ extern void sata_pmp_error_handler(struct ata_port *ap);
#ifdef CONFIG_ATA_SFF
extern const struct ata_port_operations ata_sff_port_ops;
-extern const struct ata_port_operations ata_bmdma_port_ops;
extern const struct ata_port_operations ata_bmdma32_port_ops;
/* PIO only, sg_tablesize and dma_boundary limits can be removed */
@@ -1564,11 +1570,6 @@ extern const struct ata_port_operations ata_bmdma32_port_ops;
.sg_tablesize = LIBATA_MAX_PRD, \
.dma_boundary = ATA_DMA_BOUNDARY
-#define ATA_BMDMA_SHT(drv_name) \
- ATA_BASE_SHT(drv_name), \
- .sg_tablesize = LIBATA_MAX_PRD, \
- .dma_boundary = ATA_DMA_BOUNDARY
-
extern void ata_sff_dev_select(struct ata_port *ap, unsigned int device);
extern u8 ata_sff_check_status(struct ata_port *ap);
extern void ata_sff_pause(struct ata_port *ap);
@@ -1593,7 +1594,7 @@ extern int ata_sff_hsm_move(struct ata_port *ap, struct ata_queued_cmd *qc,
extern void ata_sff_queue_pio_task(struct ata_port *ap, unsigned long delay);
extern unsigned int ata_sff_qc_issue(struct ata_queued_cmd *qc);
extern bool ata_sff_qc_fill_rtf(struct ata_queued_cmd *qc);
-extern unsigned int ata_sff_host_intr(struct ata_port *ap,
+extern unsigned int ata_sff_port_intr(struct ata_port *ap,
struct ata_queued_cmd *qc);
extern irqreturn_t ata_sff_interrupt(int irq, void *dev_instance);
extern void ata_sff_lost_interrupt(struct ata_port *ap);
@@ -1625,11 +1626,24 @@ extern int ata_pci_sff_init_one(struct pci_dev *pdev,
struct scsi_host_template *sht, void *host_priv, int hflags);
#endif /* CONFIG_PCI */
+#ifdef CONFIG_ATA_BMDMA
+
+extern const struct ata_port_operations ata_bmdma_port_ops;
+
+#define ATA_BMDMA_SHT(drv_name) \
+ ATA_BASE_SHT(drv_name), \
+ .sg_tablesize = LIBATA_MAX_PRD, \
+ .dma_boundary = ATA_DMA_BOUNDARY
+
extern void ata_bmdma_qc_prep(struct ata_queued_cmd *qc);
extern unsigned int ata_bmdma_qc_issue(struct ata_queued_cmd *qc);
extern void ata_bmdma_dumb_qc_prep(struct ata_queued_cmd *qc);
+extern unsigned int ata_bmdma_port_intr(struct ata_port *ap,
+ struct ata_queued_cmd *qc);
+extern irqreturn_t ata_bmdma_interrupt(int irq, void *dev_instance);
extern void ata_bmdma_error_handler(struct ata_port *ap);
extern void ata_bmdma_post_internal_cmd(struct ata_queued_cmd *qc);
+extern void ata_bmdma_irq_clear(struct ata_port *ap);
extern void ata_bmdma_setup(struct ata_queued_cmd *qc);
extern void ata_bmdma_start(struct ata_queued_cmd *qc);
extern void ata_bmdma_stop(struct ata_queued_cmd *qc);
@@ -1640,7 +1654,15 @@ extern int ata_bmdma_port_start32(struct ata_port *ap);
#ifdef CONFIG_PCI
extern int ata_pci_bmdma_clear_simplex(struct pci_dev *pdev);
extern void ata_pci_bmdma_init(struct ata_host *host);
+extern int ata_pci_bmdma_prepare_host(struct pci_dev *pdev,
+ const struct ata_port_info * const * ppi,
+ struct ata_host **r_host);
+extern int ata_pci_bmdma_init_one(struct pci_dev *pdev,
+ const struct ata_port_info * const * ppi,
+ struct scsi_host_template *sht,
+ void *host_priv, int hflags);
#endif /* CONFIG_PCI */
+#endif /* CONFIG_ATA_BMDMA */
/**
* ata_sff_busy_wait - Wait for a port status register
^ permalink raw reply related [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2009-12-19 19:05 ` Linus Torvalds
@ 2009-12-19 20:11 ` Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2009-12-19 20:11 UTC (permalink / raw)
To: Linus Torvalds; +Cc: Andrew Morton, linux-ide, LKML, saeed bishara
On 12/19/2009 02:05 PM, Linus Torvalds wrote:
> On Sat, 19 Dec 2009, Jeff Garzik wrote:
>>
>> to receive the following updates:
>>
>> drivers/ata/libata-scsi.c | 2 +-
>> drivers/ata/libata-sff.c | 2 +-
>> drivers/ata/pata_hpt3x2n.c | 64 ++++++++++---------
>> drivers/ata/pata_octeon_cf.c | 2 +-
>> drivers/ata/sata_mv.c | 144 ++++++++++++++++++++++++++++++++++++------
>> 5 files changed, 163 insertions(+), 51 deletions(-)
>> mode change 100644 => 100755 drivers/ata/sata_mv.c
>
> WTF is that mode change?
>
> It's introduced by commit 6481f2b52cd5411ea6342b749daf0e4f3b390d7b:
> "sata_mv: add power management support for the platform driver", and it's
> totally nonsensical.
>
> I fixed that crazy stuff when merging, but you should look at your own
> summaries a bit, and should have noticed that it was crazy. That file
> isn't an executable.
Whoops, you're absolutely right. That's broken.
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2009-12-19 18:13 Jeff Garzik
@ 2009-12-19 19:05 ` Linus Torvalds
2009-12-19 20:11 ` Jeff Garzik
0 siblings, 1 reply; 95+ messages in thread
From: Linus Torvalds @ 2009-12-19 19:05 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Andrew Morton, linux-ide, LKML
On Sat, 19 Dec 2009, Jeff Garzik wrote:
>
> to receive the following updates:
>
> drivers/ata/libata-scsi.c | 2 +-
> drivers/ata/libata-sff.c | 2 +-
> drivers/ata/pata_hpt3x2n.c | 64 ++++++++++---------
> drivers/ata/pata_octeon_cf.c | 2 +-
> drivers/ata/sata_mv.c | 144 ++++++++++++++++++++++++++++++++++++------
> 5 files changed, 163 insertions(+), 51 deletions(-)
> mode change 100644 => 100755 drivers/ata/sata_mv.c
WTF is that mode change?
It's introduced by commit 6481f2b52cd5411ea6342b749daf0e4f3b390d7b:
"sata_mv: add power management support for the platform driver", and it's
totally nonsensical.
I fixed that crazy stuff when merging, but you should look at your own
summaries a bit, and should have noticed that it was crazy. That file
isn't an executable.
Linus
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2009-12-19 18:13 Jeff Garzik
2009-12-19 19:05 ` Linus Torvalds
0 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2009-12-19 18:13 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Various fixes, and sata_mv suspend/resume support.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/libata-scsi.c | 2 +-
drivers/ata/libata-sff.c | 2 +-
drivers/ata/pata_hpt3x2n.c | 64 ++++++++++---------
drivers/ata/pata_octeon_cf.c | 2 +-
drivers/ata/sata_mv.c | 144 ++++++++++++++++++++++++++++++++++++------
5 files changed, 163 insertions(+), 51 deletions(-)
mode change 100644 => 100755 drivers/ata/sata_mv.c
Christoph Hellwig (1):
libata: use the WRITE_SAME_16 define
H Hartley Sweeten (1):
pata_octeon_cf: use resource_size(), to fix resource sizing bug
Jeff Garzik (1):
sata_mv: remove pointless NULL test
Robert Hancock (1):
libata: fix reporting of drained bytes when clearing DRQ
Saeed Bishara (6):
sata_mv: increase PIO IORDY timeout
sata_mv: support clkdev framework
sata_mv: add power management support for the platform driver
sata_mv: move the PCI bar description initialization code
sata_mv: store the board_idx into the host private data
sata_mv: add power management support for the PCI controllers.
Sergei Shtylyov (1):
pata_hpt3x2n: fix clock turnaround
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 1683ebd..f4ea5a8 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -3022,7 +3022,7 @@ static inline ata_xlat_func_t ata_get_xlat_func(struct ata_device *dev, u8 cmd)
case WRITE_16:
return ata_scsi_rw_xlat;
- case 0x93 /*WRITE_SAME_16*/:
+ case WRITE_SAME_16:
return ata_scsi_write_same_xlat;
case SYNCHRONIZE_CACHE:
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index efa8773..741065c 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -2275,7 +2275,7 @@ void ata_sff_drain_fifo(struct ata_queued_cmd *qc)
ap = qc->ap;
/* Drain up to 64K of data before we give up this recovery method */
for (count = 0; (ap->ops->sff_check_status(ap) & ATA_DRQ)
- && count < 32768; count++)
+ && count < 65536; count += 2)
ioread16(ap->ioaddr.data_addr);
/* Can become DEBUG later */
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index 9a09a1b..dd26bc7 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -8,7 +8,7 @@
* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* Portions Copyright (C) 2003 Red Hat Inc
- * Portions Copyright (C) 2005-2007 MontaVista Software, Inc.
+ * Portions Copyright (C) 2005-2009 MontaVista Software, Inc.
*
*
* TODO
@@ -25,7 +25,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x2n"
-#define DRV_VERSION "0.3.7"
+#define DRV_VERSION "0.3.8"
enum {
HPT_PCI_FAST = (1 << 31),
@@ -264,7 +264,7 @@ static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc)
static void hpt3x2n_set_clock(struct ata_port *ap, int source)
{
- void __iomem *bmdma = ap->ioaddr.bmdma_addr;
+ void __iomem *bmdma = ap->ioaddr.bmdma_addr - ap->port_no * 8;
/* Tristate the bus */
iowrite8(0x80, bmdma+0x73);
@@ -274,9 +274,9 @@ static void hpt3x2n_set_clock(struct ata_port *ap, int source)
iowrite8(source, bmdma+0x7B);
iowrite8(0xC0, bmdma+0x79);
- /* Reset state machines */
- iowrite8(0x37, bmdma+0x70);
- iowrite8(0x37, bmdma+0x74);
+ /* Reset state machines, avoid enabling the disabled channels */
+ iowrite8(ioread8(bmdma+0x70) | 0x32, bmdma+0x70);
+ iowrite8(ioread8(bmdma+0x74) | 0x32, bmdma+0x74);
/* Complete reset */
iowrite8(0x00, bmdma+0x79);
@@ -286,21 +286,10 @@ static void hpt3x2n_set_clock(struct ata_port *ap, int source)
iowrite8(0x00, bmdma+0x77);
}
-/* Check if our partner interface is busy */
-
-static int hpt3x2n_pair_idle(struct ata_port *ap)
-{
- struct ata_host *host = ap->host;
- struct ata_port *pair = host->ports[ap->port_no ^ 1];
-
- if (pair->hsm_task_state == HSM_ST_IDLE)
- return 1;
- return 0;
-}
-
static int hpt3x2n_use_dpll(struct ata_port *ap, int writing)
{
long flags = (long)ap->host->private_data;
+
/* See if we should use the DPLL */
if (writing)
return USE_DPLL; /* Needed for write */
@@ -309,20 +298,35 @@ static int hpt3x2n_use_dpll(struct ata_port *ap, int writing)
return 0;
}
+static int hpt3x2n_qc_defer(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct ata_port *alt = ap->host->ports[ap->port_no ^ 1];
+ int rc, flags = (long)ap->host->private_data;
+ int dpll = hpt3x2n_use_dpll(ap, qc->tf.flags & ATA_TFLAG_WRITE);
+
+ /* First apply the usual rules */
+ rc = ata_std_qc_defer(qc);
+ if (rc != 0)
+ return rc;
+
+ if ((flags & USE_DPLL) != dpll && alt->qc_active)
+ return ATA_DEFER_PORT;
+ return 0;
+}
+
static unsigned int hpt3x2n_qc_issue(struct ata_queued_cmd *qc)
{
- struct ata_taskfile *tf = &qc->tf;
struct ata_port *ap = qc->ap;
int flags = (long)ap->host->private_data;
+ int dpll = hpt3x2n_use_dpll(ap, qc->tf.flags & ATA_TFLAG_WRITE);
- if (hpt3x2n_pair_idle(ap)) {
- int dpll = hpt3x2n_use_dpll(ap, (tf->flags & ATA_TFLAG_WRITE));
- if ((flags & USE_DPLL) != dpll) {
- if (dpll == 1)
- hpt3x2n_set_clock(ap, 0x21);
- else
- hpt3x2n_set_clock(ap, 0x23);
- }
+ if ((flags & USE_DPLL) != dpll) {
+ flags &= ~USE_DPLL;
+ flags |= dpll;
+ ap->host->private_data = (void *)(long)flags;
+
+ hpt3x2n_set_clock(ap, dpll ? 0x21 : 0x23);
}
return ata_sff_qc_issue(qc);
}
@@ -339,6 +343,8 @@ static struct ata_port_operations hpt3x2n_port_ops = {
.inherits = &ata_bmdma_port_ops,
.bmdma_stop = hpt3x2n_bmdma_stop,
+
+ .qc_defer = hpt3x2n_qc_defer,
.qc_issue = hpt3x2n_qc_issue,
.cable_detect = hpt3x2n_cable_detect,
@@ -454,7 +460,7 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
unsigned int f_low, f_high;
int adjust;
unsigned long iobase = pci_resource_start(dev, 4);
- void *hpriv = NULL;
+ void *hpriv = (void *)USE_DPLL;
int rc;
rc = pcim_enable_device(dev);
@@ -539,7 +545,7 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
/* Set our private data up. We only need a few flags so we use
it directly */
if (pci_mhz > 60) {
- hpriv = (void *)PCI66;
+ hpriv = (void *)(PCI66 | USE_DPLL);
/*
* On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
* the MISC. register to stretch the UltraDMA Tss timing.
diff --git a/drivers/ata/pata_octeon_cf.c b/drivers/ata/pata_octeon_cf.c
index d6f6956..37ef416 100644
--- a/drivers/ata/pata_octeon_cf.c
+++ b/drivers/ata/pata_octeon_cf.c
@@ -853,7 +853,7 @@ static int __devinit octeon_cf_probe(struct platform_device *pdev)
return -EINVAL;
cs1 = devm_ioremap_nocache(&pdev->dev, res_cs1->start,
- res_cs0->end - res_cs1->start + 1);
+ resource_size(res_cs1));
if (!cs1)
return -ENOMEM;
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
old mode 100644
new mode 100755
index a8a7be0..df8ee32
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -59,6 +59,7 @@
#include <linux/dmapool.h>
#include <linux/dma-mapping.h>
#include <linux/device.h>
+#include <linux/clk.h>
#include <linux/platform_device.h>
#include <linux/ata_platform.h>
#include <linux/mbus.h>
@@ -538,6 +539,7 @@ struct mv_port_signal {
struct mv_host_priv {
u32 hp_flags;
+ unsigned int board_idx;
u32 main_irq_mask;
struct mv_port_signal signal[8];
const struct mv_hw_ops *ops;
@@ -548,6 +550,10 @@ struct mv_host_priv {
u32 irq_cause_offset;
u32 irq_mask_offset;
u32 unmask_all_irqs;
+
+#if defined(CONFIG_HAVE_CLK)
+ struct clk *clk;
+#endif
/*
* These consistent DMA memory pools give us guaranteed
* alignment for hardware-accessed data structures,
@@ -2775,7 +2781,7 @@ static void mv_port_intr(struct ata_port *ap, u32 port_cause)
struct mv_port_priv *pp;
int edma_was_enabled;
- if (!ap || (ap->flags & ATA_FLAG_DISABLED)) {
+ if (ap->flags & ATA_FLAG_DISABLED) {
mv_unexpected_intr(ap, 0);
return;
}
@@ -3393,7 +3399,7 @@ static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv,
ZERO(0x024); /* respq outp */
ZERO(0x020); /* respq inp */
ZERO(0x02c); /* test control */
- writel(0xbc, port_mmio + EDMA_IORDY_TMOUT);
+ writel(0x800, port_mmio + EDMA_IORDY_TMOUT);
}
#undef ZERO
@@ -3854,7 +3860,6 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
/**
* mv_init_host - Perform some early initialization of the host.
* @host: ATA host to initialize
- * @board_idx: controller index
*
* If possible, do an early global reset of the host. Then do
* our port init and clear/unmask all/relevant host interrupts.
@@ -3862,13 +3867,13 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
* LOCKING:
* Inherited from caller.
*/
-static int mv_init_host(struct ata_host *host, unsigned int board_idx)
+static int mv_init_host(struct ata_host *host)
{
int rc = 0, n_hc, port, hc;
struct mv_host_priv *hpriv = host->private_data;
void __iomem *mmio = hpriv->base;
- rc = mv_chip_id(host, board_idx);
+ rc = mv_chip_id(host, hpriv->board_idx);
if (rc)
goto done;
@@ -3905,14 +3910,6 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
void __iomem *port_mmio = mv_port_base(mmio, port);
mv_port_init(&ap->ioaddr, port_mmio);
-
-#ifdef CONFIG_PCI
- if (!IS_SOC(hpriv)) {
- unsigned int offset = port_mmio - mmio;
- ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio");
- ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port");
- }
-#endif
}
for (hc = 0; hc < n_hc; hc++) {
@@ -4035,12 +4032,21 @@ static int mv_platform_probe(struct platform_device *pdev)
return -ENOMEM;
host->private_data = hpriv;
hpriv->n_ports = n_ports;
+ hpriv->board_idx = chip_soc;
host->iomap = NULL;
hpriv->base = devm_ioremap(&pdev->dev, res->start,
resource_size(res));
hpriv->base -= SATAHC0_REG_BASE;
+#if defined(CONFIG_HAVE_CLK)
+ hpriv->clk = clk_get(&pdev->dev, NULL);
+ if (IS_ERR(hpriv->clk))
+ dev_notice(&pdev->dev, "cannot get clkdev\n");
+ else
+ clk_enable(hpriv->clk);
+#endif
+
/*
* (Re-)program MBUS remapping windows if we are asked to.
*/
@@ -4049,12 +4055,12 @@ static int mv_platform_probe(struct platform_device *pdev)
rc = mv_create_dma_pools(hpriv, &pdev->dev);
if (rc)
- return rc;
+ goto err;
/* initialize adapter */
- rc = mv_init_host(host, chip_soc);
+ rc = mv_init_host(host);
if (rc)
- return rc;
+ goto err;
dev_printk(KERN_INFO, &pdev->dev,
"slots %u ports %d\n", (unsigned)MV_MAX_Q_DEPTH,
@@ -4062,6 +4068,15 @@ static int mv_platform_probe(struct platform_device *pdev)
return ata_host_activate(host, platform_get_irq(pdev, 0), mv_interrupt,
IRQF_SHARED, &mv6_sht);
+err:
+#if defined(CONFIG_HAVE_CLK)
+ if (!IS_ERR(hpriv->clk)) {
+ clk_disable(hpriv->clk);
+ clk_put(hpriv->clk);
+ }
+#endif
+
+ return rc;
}
/*
@@ -4076,14 +4091,66 @@ static int __devexit mv_platform_remove(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct ata_host *host = dev_get_drvdata(dev);
-
+#if defined(CONFIG_HAVE_CLK)
+ struct mv_host_priv *hpriv = host->private_data;
+#endif
ata_host_detach(host);
+
+#if defined(CONFIG_HAVE_CLK)
+ if (!IS_ERR(hpriv->clk)) {
+ clk_disable(hpriv->clk);
+ clk_put(hpriv->clk);
+ }
+#endif
return 0;
}
+#ifdef CONFIG_PM
+static int mv_platform_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ if (host)
+ return ata_host_suspend(host, state);
+ else
+ return 0;
+}
+
+static int mv_platform_resume(struct platform_device *pdev)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ int ret;
+
+ if (host) {
+ struct mv_host_priv *hpriv = host->private_data;
+ const struct mv_sata_platform_data *mv_platform_data = \
+ pdev->dev.platform_data;
+ /*
+ * (Re-)program MBUS remapping windows if we are asked to.
+ */
+ if (mv_platform_data->dram != NULL)
+ mv_conf_mbus_windows(hpriv, mv_platform_data->dram);
+
+ /* initialize adapter */
+ ret = mv_init_host(host);
+ if (ret) {
+ printk(KERN_ERR DRV_NAME ": Error during HW init\n");
+ return ret;
+ }
+ ata_host_resume(host);
+ }
+
+ return 0;
+}
+#else
+#define mv_platform_suspend NULL
+#define mv_platform_resume NULL
+#endif
+
static struct platform_driver mv_platform_driver = {
.probe = mv_platform_probe,
.remove = __devexit_p(mv_platform_remove),
+ .suspend = mv_platform_suspend,
+ .resume = mv_platform_resume,
.driver = {
.name = DRV_NAME,
.owner = THIS_MODULE,
@@ -4094,6 +4161,9 @@ static struct platform_driver mv_platform_driver = {
#ifdef CONFIG_PCI
static int mv_pci_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent);
+#ifdef CONFIG_PM
+static int mv_pci_device_resume(struct pci_dev *pdev);
+#endif
static struct pci_driver mv_pci_driver = {
@@ -4101,6 +4171,11 @@ static struct pci_driver mv_pci_driver = {
.id_table = mv_pci_tbl,
.probe = mv_pci_init_one,
.remove = ata_pci_remove_one,
+#ifdef CONFIG_PM
+ .suspend = ata_pci_device_suspend,
+ .resume = mv_pci_device_resume,
+#endif
+
};
/* move to PCI layer or libata core? */
@@ -4194,7 +4269,7 @@ static int mv_pci_init_one(struct pci_dev *pdev,
const struct ata_port_info *ppi[] = { &mv_port_info[board_idx], NULL };
struct ata_host *host;
struct mv_host_priv *hpriv;
- int n_ports, rc;
+ int n_ports, port, rc;
if (!printed_version++)
dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
@@ -4208,6 +4283,7 @@ static int mv_pci_init_one(struct pci_dev *pdev,
return -ENOMEM;
host->private_data = hpriv;
hpriv->n_ports = n_ports;
+ hpriv->board_idx = board_idx;
/* acquire resources */
rc = pcim_enable_device(pdev);
@@ -4230,8 +4306,17 @@ static int mv_pci_init_one(struct pci_dev *pdev,
if (rc)
return rc;
+ for (port = 0; port < host->n_ports; port++) {
+ struct ata_port *ap = host->ports[port];
+ void __iomem *port_mmio = mv_port_base(hpriv->base, port);
+ unsigned int offset = port_mmio - hpriv->base;
+
+ ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio");
+ ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port");
+ }
+
/* initialize adapter */
- rc = mv_init_host(host, board_idx);
+ rc = mv_init_host(host);
if (rc)
return rc;
@@ -4247,6 +4332,27 @@ static int mv_pci_init_one(struct pci_dev *pdev,
return ata_host_activate(host, pdev->irq, mv_interrupt, IRQF_SHARED,
IS_GEN_I(hpriv) ? &mv5_sht : &mv6_sht);
}
+
+#ifdef CONFIG_PM
+static int mv_pci_device_resume(struct pci_dev *pdev)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ int rc;
+
+ rc = ata_pci_device_do_resume(pdev);
+ if (rc)
+ return rc;
+
+ /* initialize adapter */
+ rc = mv_init_host(host);
+ if (rc)
+ return rc;
+
+ ata_host_resume(host);
+
+ return 0;
+}
+#endif
#endif
static int mv_platform_probe(struct platform_device *pdev);
^ permalink raw reply related [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2009-10-06 22:26 ` Bartlomiej Zolnierkiewicz
@ 2009-10-06 23:02 ` Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2009-10-06 23:02 UTC (permalink / raw)
To: Bartlomiej Zolnierkiewicz
Cc: Jung-Ik (John) Lee, Andrew Morton, Linus Torvalds, linux-ide,
LKML, Grant Grundler, Gwendal Gringo
On 10/06/2009 06:26 PM, Bartlomiej Zolnierkiewicz wrote:
> To the previous patch. For your convenience I'll re-post all overdue
> pata_atp867x patches to the date on linux-ide ML..
Much appreciated...
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2009-10-06 4:24 ` Jeff Garzik
@ 2009-10-06 22:26 ` Bartlomiej Zolnierkiewicz
2009-10-06 23:02 ` Jeff Garzik
0 siblings, 1 reply; 95+ messages in thread
From: Bartlomiej Zolnierkiewicz @ 2009-10-06 22:26 UTC (permalink / raw)
To: Jeff Garzik
Cc: Jung-Ik (John) Lee, Andrew Morton, Linus Torvalds, linux-ide,
LKML, Grant Grundler, Gwendal Gringo
On Tuesday 06 October 2009 06:24:05 Jeff Garzik wrote:
> On 09/28/2009 11:34 AM, Bartlomiej Zolnierkiewicz wrote:
> > Thanks, your patch looks good to me but since there are still some
> > leftover issues left we would also need something like the incremental
> > patch below:
> >
> > From: Bartlomiej Zolnierkiewicz<bzolnier@gmail.com>
> > Subject: [PATCH] pata_atp867x: PIO support fixes
> >
> > * use 8 clk setting for active clocks == 7 (was 12 clk)
> > * use 12 clk setting for active clocks> 12 (was 8 clk)
> > * do 66MHz bus fixup before mapping active clocks
> > * fix setup of PIO command timings
> >
> > Signed-off-by: Bartlomiej Zolnierkiewicz<bzolnier@gmail.com>
> > ---
> > drivers/ata/pata_atp867x.c | 36 +++++++++++++++++++-----------------
> > 1 file changed, 19 insertions(+), 17 deletions(-)
> >
> > Index: b/drivers/ata/pata_atp867x.c
> > ===================================================================
> > --- a/drivers/ata/pata_atp867x.c
> > +++ b/drivers/ata/pata_atp867x.c
> > @@ -155,30 +155,31 @@ static int atp867x_get_active_clocks_shi
> > struct atp867x_priv *dp = ap->private_data;
> > unsigned char clocks = clk;
> >
> > + /*
> > + * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
> > + * on 66MHz bus
> > + */
> > + if (dp->pci66mhz)
> > + clocks++;
> > +
> > switch (clocks) {
> > case 0:
> > clocks = 1;
> > break;
> > - case 1 ... 7:
> > - break;
> > - case 9 ... 12:
> > - clocks = 7;
> > + case 1 ... 6:
> > break;
> > default:
> > printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
> > - "Using default 8clk.\n", clk);
> > + "Using 12clk.\n", clk);
> > + case 9 ... 12:
> > + clocks = 7; /* 12 clk */
> > + break;
> > + case 7:
> > case 8: /* default 8 clk */
> > clocks = 0;
> > goto active_clock_shift_done;
> > }
> >
> > - /*
> > - * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
> > - * on 66MHz bus
> > - */
> > - if (dp->pci66mhz&& clocks< 7)
> > - clocks++;
> > -
> > active_clock_shift_done:
> > return clocks<< ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
> > }
> > @@ -193,7 +194,8 @@ static int atp867x_get_recover_clocks_sh
> > break;
> > case 1 ... 11:
> > break;
> > - case 13: case 14:
> > + case 13:
> > + case 14:
> > --clocks; /* by the spec */
> > break;
> > case 15:
> > @@ -235,16 +237,16 @@ static void atp867x_set_piomode(struct a
> > iowrite8(b, dp->dma_mode);
> >
> > b = atp867x_get_active_clocks_shifted(ap, t.active) |
> > - atp867x_get_recover_clocks_shifted(t.recover);
> > + atp867x_get_recover_clocks_shifted(t.recover);
> >
> > if (adev->devno& 1)
> > iowrite8(b, dp->slave_piospd);
> > else
> > iowrite8(b, dp->mstr_piospd);
> >
> > - /*
> > - * use the same value for comand timing as for PIO timimg
> > - */
> > + b = atp867x_get_active_clocks_shifted(ap, t.act8b) |
> > + atp867x_get_recover_clocks_shifted(t.rec8b);
> > +
> > iowrite8(b, dp->eightb_piospd);
> > }
> >
> >
>
> This was incremental to the previous patch, or upstream?
To the previous patch. For your convenience I'll re-post all overdue
pata_atp867x patches to the date on linux-ide ML..
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2009-09-28 15:34 ` Bartlomiej Zolnierkiewicz
2009-09-28 20:20 ` Jung-Ik (John) Lee
2009-09-28 20:49 ` Jung-Ik (John) Lee
@ 2009-10-06 4:24 ` Jeff Garzik
2009-10-06 22:26 ` Bartlomiej Zolnierkiewicz
2 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2009-10-06 4:24 UTC (permalink / raw)
To: Bartlomiej Zolnierkiewicz
Cc: Jung-Ik (John) Lee, Andrew Morton, Linus Torvalds, linux-ide,
LKML, Grant Grundler, Gwendal Gringo
On 09/28/2009 11:34 AM, Bartlomiej Zolnierkiewicz wrote:
> Thanks, your patch looks good to me but since there are still some
> leftover issues left we would also need something like the incremental
> patch below:
>
> From: Bartlomiej Zolnierkiewicz<bzolnier@gmail.com>
> Subject: [PATCH] pata_atp867x: PIO support fixes
>
> * use 8 clk setting for active clocks == 7 (was 12 clk)
> * use 12 clk setting for active clocks> 12 (was 8 clk)
> * do 66MHz bus fixup before mapping active clocks
> * fix setup of PIO command timings
>
> Signed-off-by: Bartlomiej Zolnierkiewicz<bzolnier@gmail.com>
> ---
> drivers/ata/pata_atp867x.c | 36 +++++++++++++++++++-----------------
> 1 file changed, 19 insertions(+), 17 deletions(-)
>
> Index: b/drivers/ata/pata_atp867x.c
> ===================================================================
> --- a/drivers/ata/pata_atp867x.c
> +++ b/drivers/ata/pata_atp867x.c
> @@ -155,30 +155,31 @@ static int atp867x_get_active_clocks_shi
> struct atp867x_priv *dp = ap->private_data;
> unsigned char clocks = clk;
>
> + /*
> + * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
> + * on 66MHz bus
> + */
> + if (dp->pci66mhz)
> + clocks++;
> +
> switch (clocks) {
> case 0:
> clocks = 1;
> break;
> - case 1 ... 7:
> - break;
> - case 9 ... 12:
> - clocks = 7;
> + case 1 ... 6:
> break;
> default:
> printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
> - "Using default 8clk.\n", clk);
> + "Using 12clk.\n", clk);
> + case 9 ... 12:
> + clocks = 7; /* 12 clk */
> + break;
> + case 7:
> case 8: /* default 8 clk */
> clocks = 0;
> goto active_clock_shift_done;
> }
>
> - /*
> - * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
> - * on 66MHz bus
> - */
> - if (dp->pci66mhz&& clocks< 7)
> - clocks++;
> -
> active_clock_shift_done:
> return clocks<< ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
> }
> @@ -193,7 +194,8 @@ static int atp867x_get_recover_clocks_sh
> break;
> case 1 ... 11:
> break;
> - case 13: case 14:
> + case 13:
> + case 14:
> --clocks; /* by the spec */
> break;
> case 15:
> @@ -235,16 +237,16 @@ static void atp867x_set_piomode(struct a
> iowrite8(b, dp->dma_mode);
>
> b = atp867x_get_active_clocks_shifted(ap, t.active) |
> - atp867x_get_recover_clocks_shifted(t.recover);
> + atp867x_get_recover_clocks_shifted(t.recover);
>
> if (adev->devno& 1)
> iowrite8(b, dp->slave_piospd);
> else
> iowrite8(b, dp->mstr_piospd);
>
> - /*
> - * use the same value for comand timing as for PIO timimg
> - */
> + b = atp867x_get_active_clocks_shifted(ap, t.act8b) |
> + atp867x_get_recover_clocks_shifted(t.rec8b);
> +
> iowrite8(b, dp->eightb_piospd);
> }
>
>
This was incremental to the previous patch, or upstream?
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2009-09-28 15:34 ` Bartlomiej Zolnierkiewicz
2009-09-28 20:20 ` Jung-Ik (John) Lee
@ 2009-09-28 20:49 ` Jung-Ik (John) Lee
2009-10-06 4:24 ` Jeff Garzik
2 siblings, 0 replies; 95+ messages in thread
From: Jung-Ik (John) Lee @ 2009-09-28 20:49 UTC (permalink / raw)
To: Bartlomiej Zolnierkiewicz
Cc: Jeff Garzik, Andrew Morton, Linus Torvalds, linux-ide, LKML,
Grant Grundler, Gwendal Gringo
On Mon, Sep 28, 2009 at 8:34 AM, Bartlomiej Zolnierkiewicz
<bzolnier@gmail.com> wrote:
> On Tuesday 22 September 2009 04:36:13 Jung-Ik (John) Lee wrote:
>> On Sun, Sep 20, 2009 at 2:05 PM, Bartlomiej Zolnierkiewicz
>> <bzolnier@gmail.com> wrote:
>> > On Thursday 17 September 2009 22:49:35 Jeff Garzik wrote:
>> >>
>> >> Bug fixes, and a new driver.
>> >>
>> >>
>> >>
>> >> Please pull from 'upstream-linus' branch of
>> >> master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
>> >>
>> >> to receive the following updates:
>> >>
>> >> drivers/ata/Kconfig | 9 +
>> >> drivers/ata/Makefile | 1 +
>> >> drivers/ata/ahci.c | 4 +-
>> >> drivers/ata/libata-core.c | 4 +-
>> >> drivers/ata/pata_amd.c | 3 +
>> >> drivers/ata/pata_atp867x.c | 548 ++++++++++++++++++++++++++++++++++++++++++++
>> >> drivers/ata/sata_promise.c | 155 +++++++++++--
>> >> include/linux/pci_ids.h | 2 +
>> >> 8 files changed, 704 insertions(+), 22 deletions(-)
>> >> create mode 100644 drivers/ata/pata_atp867x.c
>> >>
>> >> John(Jung-Ik) Lee (1):
>> >> libata: Add pata_atp867x driver for Artop/Acard ATP867X controllers
>> >
>> > That was really fast.. Not necessarily a bad thing but this driver would
>> > benefit from few polishing touches..
>> >
>> >> diff --git a/drivers/ata/pata_atp867x.c b/drivers/ata/pata_atp867x.c
>> >> new file mode 100644
>> >> index 0000000..7990de9
>> >> --- /dev/null
>> >> +++ b/drivers/ata/pata_atp867x.c
>> >> @@ -0,0 +1,548 @@
>> >> +/*
>> >> + * pata_atp867x.c - ARTOP 867X 64bit 4-channel UDMA133 ATA controller driver
>> >> + *
>> >> + * (C) 2009 Google Inc. John(Jung-Ik) Lee <jilee@google.com>
>> >> + *
>> >> + * Per Atp867 data sheet rev 1.2, Acard.
>> >> + * Based in part on early ide code from
>> >> + * 2003-2004 by Eric Uhrhane, Google, Inc.
>> >> + *
>> >> + * This program is free software; you can redistribute it and/or modify
>> >> + * it under the terms of the GNU General Public License as published by
>> >> + * the Free Software Foundation; either version 2 of the License, or
>> >> + * (at your option) any later version.
>> >> + *
>> >> + * This program is distributed in the hope that it will be useful,
>> >> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> >> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> >> + * GNU General Public License for more details.
>> >> + *
>> >> + * You should have received a copy of the GNU General Public License
>> >> + * along with this program; if not, write to the Free Software
>> >> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
>> >> + *
>> >> + *
>> >> + * TODO:
>> >> + * 1. RAID features [comparison, XOR, striping, mirroring, etc.]
>> >> + */
>> >> +
>> >> +#include <linux/kernel.h>
>> >> +#include <linux/module.h>
>> >> +#include <linux/pci.h>
>> >> +#include <linux/init.h>
>> >> +#include <linux/blkdev.h>
>> >> +#include <linux/delay.h>
>> >> +#include <linux/device.h>
>> >> +#include <scsi/scsi_host.h>
>> >> +#include <linux/libata.h>
>> >> +
>> >> +#define DRV_NAME "pata_atp867x"
>> >> +#define DRV_VERSION "0.7.5"
>> >> +
>> >> +/*
>> >> + * IO Registers
>> >> + * Note that all runtime hot priv ports are cached in ap private_data
>> >> + */
>> >> +
>> >> +enum {
>> >> + ATP867X_IO_CHANNEL_OFFSET = 0x10,
>> >> +
>> >> + /*
>> >> + * IO Register Bitfields
>> >> + */
>> >> +
>> >> + ATP867X_IO_PIOSPD_ACTIVE_SHIFT = 4,
>> >> + ATP867X_IO_PIOSPD_RECOVER_SHIFT = 0,
>> >> +
>> >> + ATP867X_IO_DMAMODE_MSTR_SHIFT = 0,
>> >> + ATP867X_IO_DMAMODE_MSTR_MASK = 0x07,
>> >> + ATP867X_IO_DMAMODE_SLAVE_SHIFT = 4,
>> >> + ATP867X_IO_DMAMODE_SLAVE_MASK = 0x70,
>> >> +
>> >> + ATP867X_IO_DMAMODE_UDMA_6 = 0x07,
>> >> + ATP867X_IO_DMAMODE_UDMA_5 = 0x06,
>> >> + ATP867X_IO_DMAMODE_UDMA_4 = 0x05,
>> >> + ATP867X_IO_DMAMODE_UDMA_3 = 0x04,
>> >> + ATP867X_IO_DMAMODE_UDMA_2 = 0x03,
>> >> + ATP867X_IO_DMAMODE_UDMA_1 = 0x02,
>> >> + ATP867X_IO_DMAMODE_UDMA_0 = 0x01,
>> >> + ATP867X_IO_DMAMODE_DISABLE = 0x00,
>> >> +
>> >> + ATP867X_IO_SYS_INFO_66MHZ = 0x04,
>> >> + ATP867X_IO_SYS_INFO_SLOW_UDMA5 = 0x02,
>> >> + ATP867X_IO_SYS_MASK_RESERVED = (~0xf1),
>> >> +
>> >> + ATP867X_IO_PORTSPD_VAL = 0x1143,
>> >> + ATP867X_PREREAD_VAL = 0x0200,
>> >> +
>> >> + ATP867X_NUM_PORTS = 4,
>> >> + ATP867X_BAR_IOBASE = 0,
>> >> + ATP867X_BAR_ROMBASE = 6,
>> >> +};
>> >> +
>> >> +#define ATP867X_IOBASE(ap) ((ap)->host->iomap[0])
>> >> +#define ATP867X_SYS_INFO(ap) (0x3F + ATP867X_IOBASE(ap))
>> >> +
>> >> +#define ATP867X_IO_PORTBASE(ap, port) (0x00 + ATP867X_IOBASE(ap) + \
>> >> + (port) * ATP867X_IO_CHANNEL_OFFSET)
>> >> +#define ATP867X_IO_DMABASE(ap, port) (0x40 + \
>> >> + ATP867X_IO_PORTBASE((ap), (port)))
>> >> +
>> >> +#define ATP867X_IO_STATUS(ap, port) (0x07 + \
>> >> + ATP867X_IO_PORTBASE((ap), (port)))
>> >> +#define ATP867X_IO_ALTSTATUS(ap, port) (0x0E + \
>> >> + ATP867X_IO_PORTBASE((ap), (port)))
>> >> +
>> >> +/*
>> >> + * hot priv ports
>> >> + */
>> >> +#define ATP867X_IO_MSTRPIOSPD(ap, port) (0x08 + \
>> >> + ATP867X_IO_DMABASE((ap), (port)))
>> >> +#define ATP867X_IO_SLAVPIOSPD(ap, port) (0x09 + \
>> >> + ATP867X_IO_DMABASE((ap), (port)))
>> >> +#define ATP867X_IO_8BPIOSPD(ap, port) (0x0A + \
>> >> + ATP867X_IO_DMABASE((ap), (port)))
>> >> +#define ATP867X_IO_DMAMODE(ap, port) (0x0B + \
>> >> + ATP867X_IO_DMABASE((ap), (port)))
>> >> +
>> >> +#define ATP867X_IO_PORTSPD(ap, port) (0x4A + \
>> >> + ATP867X_IO_PORTBASE((ap), (port)))
>> >> +#define ATP867X_IO_PREREAD(ap, port) (0x4C + \
>> >> + ATP867X_IO_PORTBASE((ap), (port)))
>> >> +
>> >> +struct atp867x_priv {
>> >> + void __iomem *dma_mode;
>> >> + void __iomem *mstr_piospd;
>> >> + void __iomem *slave_piospd;
>> >> + void __iomem *eightb_piospd;
>> >> + int pci66mhz;
>> >> +};
>> >> +
>> >> +static inline u8 atp867x_speed_to_mode(u8 speed)
>> >> +{
>> >> + return speed - XFER_UDMA_0 + 1;
>> >> +}
>> >> +
>> >> +static void atp867x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
>> >> +{
>> >> + struct pci_dev *pdev = to_pci_dev(ap->host->dev);
>> >> + struct atp867x_priv *dp = ap->private_data;
>> >> + u8 speed = adev->dma_mode;
>> >> + u8 b;
>> >> + u8 mode;
>> >> +
>> >> + mode = atp867x_speed_to_mode(speed);
>> >
>> > The driver currently doesn't support MWDMA modes but claims otherwise
>> > (fixed in the attached patch).
>> >
>> >> + /*
>> >> + * Doc 6.6.9: decrease the udma mode value by 1 for safer UDMA speed
>> >> + * on 66MHz bus
>> >> + * rev-A: UDMA_1~4 (5, 6 no change)
>> >> + * rev-B: all UDMA modes
>> >> + * UDMA_0 stays not to disable UDMA
>> >> + */
>> >> + if (dp->pci66mhz && mode > ATP867X_IO_DMAMODE_UDMA_0 &&
>> >> + (pdev->device == PCI_DEVICE_ID_ARTOP_ATP867B ||
>> >> + mode < ATP867X_IO_DMAMODE_UDMA_5))
>> >> + mode--;
>> >> +
>> >> + b = ioread8(dp->dma_mode);
>> >> + if (adev->devno & 1) {
>> >> + b = (b & ~ATP867X_IO_DMAMODE_SLAVE_MASK) |
>> >> + (mode << ATP867X_IO_DMAMODE_SLAVE_SHIFT);
>> >> + } else {
>> >> + b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK) |
>> >> + (mode << ATP867X_IO_DMAMODE_MSTR_SHIFT);
>> >> + }
>> >> + iowrite8(b, dp->dma_mode);
>> >> +}
>> >> +
>> >> +static int atp867x_get_active_clocks_shifted(unsigned int clk)
>> >> +{
>> >> + unsigned char clocks = clk;
>> >> +
>> >> + switch (clocks) {
>> >> + case 0:
>> >> + clocks = 1;
>> >> + break;
>> >> + case 1 ... 7:
>> >> + break;
>> >> + case 8 ... 12:
>> >> + clocks = 7;
>> >
>> > Shouldn't "clocks = 0" (the default case) be used here?
>>
>> The clocks value 0 sets it to 8 clocks, while value 7 sets to 12 clocks.
>
> This would explain it but then there is no need to use "clocks = 7"
> for the _input_ "clocks == 7".
>
>> I cleaned up a bit on clocks_shift. See the patch below.
>>
>> > Otherwise it seems to result in underclocked timings for dp->pci66mhz == 0.
>> >
>> >> + break;
>> >> + default:
>> >> + printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
>> >> + "Using default 8clk.\n", clk);
>> >> + clocks = 0; /* 8 clk */
>> >> + break;
>> >> + }
>> >> + return clocks << ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
>> >> +}
>> >> +
>> >> +static int atp867x_get_recover_clocks_shifted(unsigned int clk)
>> >> +{
>> >> + unsigned char clocks = clk;
>> >> +
>> >> + switch (clocks) {
>> >> + case 0:
>> >> + clocks = 1;
>> >> + break;
>> >> + case 1 ... 11:
>> >> + break;
>> >> + case 12:
>> >> + clocks = 0;
>> >> + break;
>> >> + case 13: case 14:
>> >> + --clocks;
>> >> + break;
>> >
>> > Is "clocks == 14" a reserved setting?
>>
>> 12 is reserved for the default (== 0), and 13, 14 are set to value 12,
>> 13 respectively.
>
> I meant the _output_ "clocks == 14" here.
>
>> >
>> > If so a comment documenting it would be appreciated.
>>
>> Sure. see the new patch below.
>>
>> >
>> >> + case 15:
>> >> + break;
>> >> + default:
>> >> + printk(KERN_WARNING "ATP867X: recover %dclk is invalid. "
>> >> + "Using default 15clk.\n", clk);
>> >> + clocks = 0; /* 12 clk */
>> >
>> > Shouldn't it use "clocks == 15" setting?
>> It was a typo. 12 is the right default.
>>
>> >
>> >> + break;
>> >> + }
>> >> + return clocks << ATP867X_IO_PIOSPD_RECOVER_SHIFT;
>> >> +}
>> >> +
>> >> +static void atp867x_set_piomode(struct ata_port *ap, struct ata_device *adev)
>> >> +{
>> >> + struct ata_device *peer = ata_dev_pair(adev);
>> >> + struct atp867x_priv *dp = ap->private_data;
>> >> + u8 speed = adev->pio_mode;
>> >> + struct ata_timing t, p;
>> >> + int T, UT;
>> >> + u8 b;
>> >> +
>> >> + T = 1000000000 / 33333;
>> >> + UT = T / 4;
>> >> +
>> >> + ata_timing_compute(adev, speed, &t, T, UT);
>> >> + if (peer && peer->pio_mode) {
>> >> + ata_timing_compute(peer, peer->pio_mode, &p, T, UT);
>> >> + ata_timing_merge(&p, &t, &t, ATA_TIMING_8BIT);
>> >> + }
>> >> +
>> >> + b = ioread8(dp->dma_mode);
>> >> + if (adev->devno & 1)
>> >> + b = (b & ~ATP867X_IO_DMAMODE_SLAVE_MASK);
>> >> + else
>> >> + b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK);
>> >> + iowrite8(b, dp->dma_mode);
>> >> +
>> >> + b = atp867x_get_active_clocks_shifted(t.active) |
>> >> + atp867x_get_recover_clocks_shifted(t.recover);
>> >> + if (dp->pci66mhz)
>> >> + b += 0x10;
>> >
>> > What is the purpose of the above hack?
>>
>> For safe PIO mode according to spec.
>>
>> >
>> > AFAICS (I don't have a datasheet) it may result in invalid active
>> > clocks being used for t.active > 12 and 0x80 bit being set incorrectly
>> > for t.active values 7..12 (unless it was the purpose of the hack).
>>
>> See the patch below..
>>
>> >
>> >> + if (adev->devno & 1)
>> >> + iowrite8(b, dp->slave_piospd);
>> >> + else
>> >> + iowrite8(b, dp->mstr_piospd);
>> >> +
>> >> + /*
>> >> + * use the same value for comand timing as for PIO timimg
>> >> + */
>> >> + iowrite8(b, dp->eightb_piospd);
>> >
>> > This is incorrect if slave/master devices use different PIO modes
>> > or if PIO mode <= 2 is used by any device.
>> >
>> > Timing based on t.act8b and t.rec8b values should be used instead.
>>
>> act8b and rec8b have the same values as active, recovery of the port.
>
> Please take a look at drivers/ata/libata-core.c::ata_timing[] table:
>
> ...
> { XFER_PIO_0, 70, 290, 240, 600, 165, 150, 0, 600, 0 },
> { XFER_PIO_1, 50, 290, 93, 383, 125, 100, 0, 383, 0 },
> { XFER_PIO_2, 30, 290, 40, 330, 100, 90, 0, 240, 0 },
> { XFER_PIO_3, 30, 80, 70, 180, 80, 70, 0, 180, 0 },
> { XFER_PIO_4, 25, 70, 25, 120, 70, 25, 0, 120, 0 },
> { XFER_PIO_5, 15, 65, 25, 100, 65, 25, 0, 100, 0 },
> { XFER_PIO_6, 10, 55, 20, 80, 55, 20, 0, 80, 0 },
> ...
>
> For PIO modes <= 2 (or if master/slave devices use different PIO modes)
> we'll have different values, i.e. for PIO2 in case of a single device on
> the port using standard timings we'll have:
>
> t.active = 4
> t.recovery = 4
> t.act8b = 10
> t.rec8b = 2
>
> Most likely we won't see much use of this driver with older devices,
> however this should not stop us from supporting them and at the same
> time making the driver easier to maintain.
>
>> If a:r=3:1 then they become 4:1 on 66mhz for safer transfer, and
>> a8:r8=3:1, which is identical but the a8 should be incremented by 1.
>> I can use a8:r8 with 66mhz fixup but it becomes the same as using a:r.
>> Take a look at the patch below.
>>
>> >
>> > On the somehow related note:
>> >
>> > * I don't see how PIO0-2 command timings can be met with only 3 bits
>> > used for active clocks. Could it be that dp->eight_piospd should be
>> > programmed in a slightly different way than dp->{mstr,slave}_piospd?
>> >
>>
>> See new patch on clocks_shift below.
>>
>> > * The controller allows higher clocks values for recovery timings but
>> > ata_timing_compute() tries to fairly increase both recovery and active
>> > timings to meet the required cycle timing.
>> >
>> >> +}
>> >> +
>> >> +static int atp867x_cable_detect(struct ata_port *ap)
>> >> +{
>> >> + return ATA_CBL_PATA40_SHORT;
>> >> +}
>> >
>> > As noticed by Robert and Alan already:
>> >
>> > This should use ATA_CBL_PATA_UNK and rely on the driver-side cable detection.
>>
>> I modified cable_detect() to use override; on a certain
>> subsystem_vendor|device, its 40short, others, unknown.
>>
>> >
>> >
>> > One last thing: Power Management support is missing from this driver
>> > (I tried addressing this in the separately posted patch but it needs
>> > testing by somebody with the hardware).
>> >
>> >
>> > MWDMA fix:
>> >
>> > From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
>> > Subject: [PATCH] pata_atp867x: fix it to not claim MWDMA support
>> >
>> > MWDMA modes are not supported by this driver currently.
>> >
>> > Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
>> > ---
>> > drivers/ata/pata_atp867x.c | 10 +---------
>> > 1 file changed, 1 insertion(+), 9 deletions(-)
>> >
>> > Index: b/drivers/ata/pata_atp867x.c
>> > ===================================================================
>> > --- a/drivers/ata/pata_atp867x.c
>> > +++ b/drivers/ata/pata_atp867x.c
>> > @@ -118,20 +118,13 @@ struct atp867x_priv {
>> > int pci66mhz;
>> > };
>> >
>> > -static inline u8 atp867x_speed_to_mode(u8 speed)
>> > -{
>> > - return speed - XFER_UDMA_0 + 1;
>> > -}
>> > -
>> > static void atp867x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
>> > {
>> > struct pci_dev *pdev = to_pci_dev(ap->host->dev);
>> > struct atp867x_priv *dp = ap->private_data;
>> > u8 speed = adev->dma_mode;
>> > u8 b;
>> > - u8 mode;
>> > -
>> > - mode = atp867x_speed_to_mode(speed);
>> > + u8 mode = speed - XFER_UDMA_0 + 1;
>> >
>> > /*
>> > * Doc 6.6.9: decrease the udma mode value by 1 for safer UDMA speed
>> > @@ -471,7 +464,6 @@ static int atp867x_init_one(struct pci_d
>> > static const struct ata_port_info info_867x = {
>> > .flags = ATA_FLAG_SLAVE_POSS,
>> > .pio_mask = ATA_PIO4,
>> > - .mwdma_mask = ATA_MWDMA2,
>>
>> This looks good to me. thx.
>>
>> > .udma_mask = ATA_UDMA6,
>> > .port_ops = &atp867x_ops,
>> > };
>> >
>>
>>
>> From: John(Jung-Ik) Lee <jilee@google.com>
>>
>> clarifications in timings calculations and cable detection
>>
>> Signed-off-by: John(Jung-Ik) Lee <jilee@google.com>
>> ---
>>
>> pata_atp867x.c | 50 +++++++++++++++++++++++++++++++++++++-------------
>> 1 files changed, 37 insertions, 13 deletions
>>
>> diff --git a/drivers/ata/pata_atp867x.c b/drivers/ata/pata_atp867x.c
>> index e6c4706..c1c691f 100644
>> --- a/drivers/ata/pata_atp867x.c
>> +++ b/drivers/ata/pata_atp867x.c
>> @@ -156,8 +156,10 @@ static void atp867x_set_dmamode(struct ata_port
>> *ap, struct ata_device *adev)
>> iowrite8(b, dp->dma_mode);
>> }
>>
>> -static int atp867x_get_active_clocks_shifted(unsigned int clk)
>> +static int atp867x_get_active_clocks_shifted(struct ata_port *ap,
>> + unsigned int clk)
>> {
>> + struct atp867x_priv *dp = ap->private_data;
>> unsigned char clocks = clk;
>>
>> switch (clocks) {
>> @@ -166,15 +168,25 @@ static int
>> atp867x_get_active_clocks_shifted(unsigned int clk)
>> break;
>> case 1 ... 7:
>> break;
>> - case 8 ... 12:
>> + case 9 ... 12:
>> clocks = 7;
>> break;
>> default:
>> printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
>> "Using default 8clk.\n", clk);
>> - clocks = 0; /* 8 clk */
>> - break;
>> + case 8: /* default 8 clk */
>> + clocks = 0;
>> + goto active_clock_shift_done;
>> }
>> +
>> + /*
>> + * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
>> + * on 66MHz bus
>> + */
>> + if (dp->pci66mhz && clocks < 7)
>> + clocks++;
>> +
>> +active_clock_shift_done:
>> return clocks << ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
>> }
>>
>> @@ -188,20 +200,19 @@ static int
>> atp867x_get_recover_clocks_shifted(unsigned int clk)
>> break;
>> case 1 ... 11:
>> break;
>> - case 12:
>> - clocks = 0;
>> - break;
>> case 13: case 14:
>> - --clocks;
>> + --clocks; /* by the spec */
>> break;
>> case 15:
>> break;
>> default:
>> printk(KERN_WARNING "ATP867X: recover %dclk is invalid. "
>> "Using default 12clk.\n", clk);
>> - clocks = 0; /* 12 clk */
>> + case 12: /* default 12 clk */
>> + clocks = 0;
>> break;
>> }
>> +
>> return clocks << ATP867X_IO_PIOSPD_RECOVER_SHIFT;
>> }
>>
>> @@ -230,10 +241,8 @@ static void atp867x_set_piomode(struct ata_port
>> *ap, struct ata_device *adev)
>> b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK);
>> iowrite8(b, dp->dma_mode);
>>
>> - b = atp867x_get_active_clocks_shifted(t.active) |
>> + b = atp867x_get_active_clocks_shifted(ap, t.active) |
>> atp867x_get_recover_clocks_shifted(t.recover);
>> - if (dp->pci66mhz)
>> - b += 0x10;
>>
>> if (adev->devno & 1)
>> iowrite8(b, dp->slave_piospd);
>> @@ -246,9 +255,24 @@ static void atp867x_set_piomode(struct ata_port
>> *ap, struct ata_device *adev)
>> iowrite8(b, dp->eightb_piospd);
>> }
>>
>> +static int atp867x_cable_override(struct pci_dev *pdev)
>> +{
>> + if (pdev->subsystem_vendor == PCI_VENDOR_ID_ARTOP &&
>> + (pdev->subsystem_device == PCI_DEVICE_ID_ARTOP_ATP867A ||
>> + pdev->subsystem_device == PCI_DEVICE_ID_ARTOP_ATP867B)) {
>> + return 1;
>> + }
>> + return 0;
>> +}
>> +
>> static int atp867x_cable_detect(struct ata_port *ap)
>> {
>> - return ATA_CBL_PATA40_SHORT;
>> + struct pci_dev *pdev = to_pci_dev(ap->host->dev);
>> +
>> + if (atp867x_cable_override(pdev))
>> + return ATA_CBL_PATA40_SHORT;
>> +
>> + return ATA_CBL_PATA_UNK;
>> }
>>
>> static struct scsi_host_template atp867x_sht = {
>
> Thanks, your patch looks good to me but since there are still some
> leftover issues left we would also need something like the incremental
> patch below:
>
> From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Subject: [PATCH] pata_atp867x: PIO support fixes
>
> * use 8 clk setting for active clocks == 7 (was 12 clk)
> * use 12 clk setting for active clocks > 12 (was 8 clk)
> * do 66MHz bus fixup before mapping active clocks
> * fix setup of PIO command timings
>
> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> ---
> drivers/ata/pata_atp867x.c | 36 +++++++++++++++++++-----------------
> 1 file changed, 19 insertions(+), 17 deletions(-)
>
> Index: b/drivers/ata/pata_atp867x.c
> ===================================================================
> --- a/drivers/ata/pata_atp867x.c
> +++ b/drivers/ata/pata_atp867x.c
> @@ -155,30 +155,31 @@ static int atp867x_get_active_clocks_shi
> struct atp867x_priv *dp = ap->private_data;
> unsigned char clocks = clk;
>
> + /*
> + * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
> + * on 66MHz bus
> + */
> + if (dp->pci66mhz)
> + clocks++;
> +
> switch (clocks) {
> case 0:
> clocks = 1;
> break;
> - case 1 ... 7:
> - break;
> - case 9 ... 12:
> - clocks = 7;
> + case 1 ... 6:
> break;
> default:
> printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
> - "Using default 8clk.\n", clk);
> + "Using 12clk.\n", clk);
> + case 9 ... 12:
> + clocks = 7; /* 12 clk */
> + break;
> + case 7:
> case 8: /* default 8 clk */
> clocks = 0;
> goto active_clock_shift_done;
> }
>
> - /*
> - * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
> - * on 66MHz bus
> - */
> - if (dp->pci66mhz && clocks < 7)
> - clocks++;
> -
> active_clock_shift_done:
> return clocks << ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
> }
> @@ -193,7 +194,8 @@ static int atp867x_get_recover_clocks_sh
> break;
> case 1 ... 11:
> break;
> - case 13: case 14:
> + case 13:
> + case 14:
> --clocks; /* by the spec */
> break;
> case 15:
> @@ -235,16 +237,16 @@ static void atp867x_set_piomode(struct a
> iowrite8(b, dp->dma_mode);
>
> b = atp867x_get_active_clocks_shifted(ap, t.active) |
> - atp867x_get_recover_clocks_shifted(t.recover);
> + atp867x_get_recover_clocks_shifted(t.recover);
>
> if (adev->devno & 1)
> iowrite8(b, dp->slave_piospd);
> else
> iowrite8(b, dp->mstr_piospd);
>
> - /*
> - * use the same value for comand timing as for PIO timimg
> - */
> + b = atp867x_get_active_clocks_shifted(ap, t.act8b) |
> + atp867x_get_recover_clocks_shifted(t.rec8b);
> +
> iowrite8(b, dp->eightb_piospd);
> }
>
>
Looks good. Thanks Bart.
Acked-by: Jung-Ik (John) Lee <jilee@google.com>
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2009-09-28 20:20 ` Jung-Ik (John) Lee
@ 2009-09-28 20:36 ` Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2009-09-28 20:36 UTC (permalink / raw)
To: Jung-Ik (John) Lee
Cc: Bartlomiej Zolnierkiewicz, Andrew Morton, Linus Torvalds,
linux-ide, LKML, Grant Grundler, Gwendal Gringo
On 09/28/2009 04:20 PM, Jung-Ik (John) Lee wrote:
>> Thanks, your patch looks good to me but since there are still some
>> leftover issues left we would also need something like the incremental
>> patch below:
>
> [resending - bounced back from -ide, -kernel]
>
> your patch below looks good to me.
By convention, you should reply to a patch such as Bart's, and provide
an explicit line of text that may be pasted into the patch at merge time:
Acked-by: Your Name <your@email.address>
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2009-09-28 15:34 ` Bartlomiej Zolnierkiewicz
@ 2009-09-28 20:20 ` Jung-Ik (John) Lee
2009-09-28 20:36 ` Jeff Garzik
2009-09-28 20:49 ` Jung-Ik (John) Lee
2009-10-06 4:24 ` Jeff Garzik
2 siblings, 1 reply; 95+ messages in thread
From: Jung-Ik (John) Lee @ 2009-09-28 20:20 UTC (permalink / raw)
To: Bartlomiej Zolnierkiewicz
Cc: Jeff Garzik, Andrew Morton, Linus Torvalds, linux-ide, LKML,
Grant Grundler, Gwendal Gringo
On Mon, Sep 28, 2009 at 8:34 AM, Bartlomiej Zolnierkiewicz
<bzolnier@gmail.com> wrote:
> On Tuesday 22 September 2009 04:36:13 Jung-Ik (John) Lee wrote:
>> On Sun, Sep 20, 2009 at 2:05 PM, Bartlomiej Zolnierkiewicz
>> <bzolnier@gmail.com> wrote:
>> > On Thursday 17 September 2009 22:49:35 Jeff Garzik wrote:
>> >>
>> >> Bug fixes, and a new driver.
>> >>
>> >>
>> >>
>> >> Please pull from 'upstream-linus' branch of
>> >> master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
>> >>
>> >> to receive the following updates:
>> >>
>> >> drivers/ata/Kconfig | 9 +
>> >> drivers/ata/Makefile | 1 +
>> >> drivers/ata/ahci.c | 4 +-
>> >> drivers/ata/libata-core.c | 4 +-
>> >> drivers/ata/pata_amd.c | 3 +
>> >> drivers/ata/pata_atp867x.c | 548 ++++++++++++++++++++++++++++++++++++++++++++
>> >> drivers/ata/sata_promise.c | 155 +++++++++++--
>> >> include/linux/pci_ids.h | 2 +
>> >> 8 files changed, 704 insertions(+), 22 deletions(-)
>> >> create mode 100644 drivers/ata/pata_atp867x.c
>> >>
>> >> John(Jung-Ik) Lee (1):
>> >> libata: Add pata_atp867x driver for Artop/Acard ATP867X controllers
>> >
>> > That was really fast.. Not necessarily a bad thing but this driver would
>> > benefit from few polishing touches..
>> >
>> >> diff --git a/drivers/ata/pata_atp867x.c b/drivers/ata/pata_atp867x.c
>> >> new file mode 100644
>> >> index 0000000..7990de9
>> >> --- /dev/null
>> >> +++ b/drivers/ata/pata_atp867x.c
>> >> @@ -0,0 +1,548 @@
>> >> +/*
>> >> + * pata_atp867x.c - ARTOP 867X 64bit 4-channel UDMA133 ATA controller driver
>> >> + *
>> >> + * (C) 2009 Google Inc. John(Jung-Ik) Lee <jilee@google.com>
>> >> + *
>> >> + * Per Atp867 data sheet rev 1.2, Acard.
>> >> + * Based in part on early ide code from
>> >> + * 2003-2004 by Eric Uhrhane, Google, Inc.
>> >> + *
>> >> + * This program is free software; you can redistribute it and/or modify
>> >> + * it under the terms of the GNU General Public License as published by
>> >> + * the Free Software Foundation; either version 2 of the License, or
>> >> + * (at your option) any later version.
>> >> + *
>> >> + * This program is distributed in the hope that it will be useful,
>> >> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> >> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> >> + * GNU General Public License for more details.
>> >> + *
>> >> + * You should have received a copy of the GNU General Public License
>> >> + * along with this program; if not, write to the Free Software
>> >> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
>> >> + *
>> >> + *
>> >> + * TODO:
>> >> + * 1. RAID features [comparison, XOR, striping, mirroring, etc.]
>> >> + */
>> >> +
>> >> +#include <linux/kernel.h>
>> >> +#include <linux/module.h>
>> >> +#include <linux/pci.h>
>> >> +#include <linux/init.h>
>> >> +#include <linux/blkdev.h>
>> >> +#include <linux/delay.h>
>> >> +#include <linux/device.h>
>> >> +#include <scsi/scsi_host.h>
>> >> +#include <linux/libata.h>
>> >> +
>> >> +#define DRV_NAME "pata_atp867x"
>> >> +#define DRV_VERSION "0.7.5"
>> >> +
>> >> +/*
>> >> + * IO Registers
>> >> + * Note that all runtime hot priv ports are cached in ap private_data
>> >> + */
>> >> +
>> >> +enum {
>> >> + ATP867X_IO_CHANNEL_OFFSET = 0x10,
>> >> +
>> >> + /*
>> >> + * IO Register Bitfields
>> >> + */
>> >> +
>> >> + ATP867X_IO_PIOSPD_ACTIVE_SHIFT = 4,
>> >> + ATP867X_IO_PIOSPD_RECOVER_SHIFT = 0,
>> >> +
>> >> + ATP867X_IO_DMAMODE_MSTR_SHIFT = 0,
>> >> + ATP867X_IO_DMAMODE_MSTR_MASK = 0x07,
>> >> + ATP867X_IO_DMAMODE_SLAVE_SHIFT = 4,
>> >> + ATP867X_IO_DMAMODE_SLAVE_MASK = 0x70,
>> >> +
>> >> + ATP867X_IO_DMAMODE_UDMA_6 = 0x07,
>> >> + ATP867X_IO_DMAMODE_UDMA_5 = 0x06,
>> >> + ATP867X_IO_DMAMODE_UDMA_4 = 0x05,
>> >> + ATP867X_IO_DMAMODE_UDMA_3 = 0x04,
>> >> + ATP867X_IO_DMAMODE_UDMA_2 = 0x03,
>> >> + ATP867X_IO_DMAMODE_UDMA_1 = 0x02,
>> >> + ATP867X_IO_DMAMODE_UDMA_0 = 0x01,
>> >> + ATP867X_IO_DMAMODE_DISABLE = 0x00,
>> >> +
>> >> + ATP867X_IO_SYS_INFO_66MHZ = 0x04,
>> >> + ATP867X_IO_SYS_INFO_SLOW_UDMA5 = 0x02,
>> >> + ATP867X_IO_SYS_MASK_RESERVED = (~0xf1),
>> >> +
>> >> + ATP867X_IO_PORTSPD_VAL = 0x1143,
>> >> + ATP867X_PREREAD_VAL = 0x0200,
>> >> +
>> >> + ATP867X_NUM_PORTS = 4,
>> >> + ATP867X_BAR_IOBASE = 0,
>> >> + ATP867X_BAR_ROMBASE = 6,
>> >> +};
>> >> +
>> >> +#define ATP867X_IOBASE(ap) ((ap)->host->iomap[0])
>> >> +#define ATP867X_SYS_INFO(ap) (0x3F + ATP867X_IOBASE(ap))
>> >> +
>> >> +#define ATP867X_IO_PORTBASE(ap, port) (0x00 + ATP867X_IOBASE(ap) + \
>> >> + (port) * ATP867X_IO_CHANNEL_OFFSET)
>> >> +#define ATP867X_IO_DMABASE(ap, port) (0x40 + \
>> >> + ATP867X_IO_PORTBASE((ap), (port)))
>> >> +
>> >> +#define ATP867X_IO_STATUS(ap, port) (0x07 + \
>> >> + ATP867X_IO_PORTBASE((ap), (port)))
>> >> +#define ATP867X_IO_ALTSTATUS(ap, port) (0x0E + \
>> >> + ATP867X_IO_PORTBASE((ap), (port)))
>> >> +
>> >> +/*
>> >> + * hot priv ports
>> >> + */
>> >> +#define ATP867X_IO_MSTRPIOSPD(ap, port) (0x08 + \
>> >> + ATP867X_IO_DMABASE((ap), (port)))
>> >> +#define ATP867X_IO_SLAVPIOSPD(ap, port) (0x09 + \
>> >> + ATP867X_IO_DMABASE((ap), (port)))
>> >> +#define ATP867X_IO_8BPIOSPD(ap, port) (0x0A + \
>> >> + ATP867X_IO_DMABASE((ap), (port)))
>> >> +#define ATP867X_IO_DMAMODE(ap, port) (0x0B + \
>> >> + ATP867X_IO_DMABASE((ap), (port)))
>> >> +
>> >> +#define ATP867X_IO_PORTSPD(ap, port) (0x4A + \
>> >> + ATP867X_IO_PORTBASE((ap), (port)))
>> >> +#define ATP867X_IO_PREREAD(ap, port) (0x4C + \
>> >> + ATP867X_IO_PORTBASE((ap), (port)))
>> >> +
>> >> +struct atp867x_priv {
>> >> + void __iomem *dma_mode;
>> >> + void __iomem *mstr_piospd;
>> >> + void __iomem *slave_piospd;
>> >> + void __iomem *eightb_piospd;
>> >> + int pci66mhz;
>> >> +};
>> >> +
>> >> +static inline u8 atp867x_speed_to_mode(u8 speed)
>> >> +{
>> >> + return speed - XFER_UDMA_0 + 1;
>> >> +}
>> >> +
>> >> +static void atp867x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
>> >> +{
>> >> + struct pci_dev *pdev = to_pci_dev(ap->host->dev);
>> >> + struct atp867x_priv *dp = ap->private_data;
>> >> + u8 speed = adev->dma_mode;
>> >> + u8 b;
>> >> + u8 mode;
>> >> +
>> >> + mode = atp867x_speed_to_mode(speed);
>> >
>> > The driver currently doesn't support MWDMA modes but claims otherwise
>> > (fixed in the attached patch).
>> >
>> >> + /*
>> >> + * Doc 6.6.9: decrease the udma mode value by 1 for safer UDMA speed
>> >> + * on 66MHz bus
>> >> + * rev-A: UDMA_1~4 (5, 6 no change)
>> >> + * rev-B: all UDMA modes
>> >> + * UDMA_0 stays not to disable UDMA
>> >> + */
>> >> + if (dp->pci66mhz && mode > ATP867X_IO_DMAMODE_UDMA_0 &&
>> >> + (pdev->device == PCI_DEVICE_ID_ARTOP_ATP867B ||
>> >> + mode < ATP867X_IO_DMAMODE_UDMA_5))
>> >> + mode--;
>> >> +
>> >> + b = ioread8(dp->dma_mode);
>> >> + if (adev->devno & 1) {
>> >> + b = (b & ~ATP867X_IO_DMAMODE_SLAVE_MASK) |
>> >> + (mode << ATP867X_IO_DMAMODE_SLAVE_SHIFT);
>> >> + } else {
>> >> + b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK) |
>> >> + (mode << ATP867X_IO_DMAMODE_MSTR_SHIFT);
>> >> + }
>> >> + iowrite8(b, dp->dma_mode);
>> >> +}
>> >> +
>> >> +static int atp867x_get_active_clocks_shifted(unsigned int clk)
>> >> +{
>> >> + unsigned char clocks = clk;
>> >> +
>> >> + switch (clocks) {
>> >> + case 0:
>> >> + clocks = 1;
>> >> + break;
>> >> + case 1 ... 7:
>> >> + break;
>> >> + case 8 ... 12:
>> >> + clocks = 7;
>> >
>> > Shouldn't "clocks = 0" (the default case) be used here?
>>
>> The clocks value 0 sets it to 8 clocks, while value 7 sets to 12 clocks.
>
> This would explain it but then there is no need to use "clocks = 7"
> for the _input_ "clocks == 7".
>
>> I cleaned up a bit on clocks_shift. See the patch below.
>>
>> > Otherwise it seems to result in underclocked timings for dp->pci66mhz == 0.
>> >
>> >> + break;
>> >> + default:
>> >> + printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
>> >> + "Using default 8clk.\n", clk);
>> >> + clocks = 0; /* 8 clk */
>> >> + break;
>> >> + }
>> >> + return clocks << ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
>> >> +}
>> >> +
>> >> +static int atp867x_get_recover_clocks_shifted(unsigned int clk)
>> >> +{
>> >> + unsigned char clocks = clk;
>> >> +
>> >> + switch (clocks) {
>> >> + case 0:
>> >> + clocks = 1;
>> >> + break;
>> >> + case 1 ... 11:
>> >> + break;
>> >> + case 12:
>> >> + clocks = 0;
>> >> + break;
>> >> + case 13: case 14:
>> >> + --clocks;
>> >> + break;
>> >
>> > Is "clocks == 14" a reserved setting?
>>
>> 12 is reserved for the default (== 0), and 13, 14 are set to value 12,
>> 13 respectively.
>
> I meant the _output_ "clocks == 14" here.
>
>> >
>> > If so a comment documenting it would be appreciated.
>>
>> Sure. see the new patch below.
>>
>> >
>> >> + case 15:
>> >> + break;
>> >> + default:
>> >> + printk(KERN_WARNING "ATP867X: recover %dclk is invalid. "
>> >> + "Using default 15clk.\n", clk);
>> >> + clocks = 0; /* 12 clk */
>> >
>> > Shouldn't it use "clocks == 15" setting?
>> It was a typo. 12 is the right default.
>>
>> >
>> >> + break;
>> >> + }
>> >> + return clocks << ATP867X_IO_PIOSPD_RECOVER_SHIFT;
>> >> +}
>> >> +
>> >> +static void atp867x_set_piomode(struct ata_port *ap, struct ata_device *adev)
>> >> +{
>> >> + struct ata_device *peer = ata_dev_pair(adev);
>> >> + struct atp867x_priv *dp = ap->private_data;
>> >> + u8 speed = adev->pio_mode;
>> >> + struct ata_timing t, p;
>> >> + int T, UT;
>> >> + u8 b;
>> >> +
>> >> + T = 1000000000 / 33333;
>> >> + UT = T / 4;
>> >> +
>> >> + ata_timing_compute(adev, speed, &t, T, UT);
>> >> + if (peer && peer->pio_mode) {
>> >> + ata_timing_compute(peer, peer->pio_mode, &p, T, UT);
>> >> + ata_timing_merge(&p, &t, &t, ATA_TIMING_8BIT);
>> >> + }
>> >> +
>> >> + b = ioread8(dp->dma_mode);
>> >> + if (adev->devno & 1)
>> >> + b = (b & ~ATP867X_IO_DMAMODE_SLAVE_MASK);
>> >> + else
>> >> + b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK);
>> >> + iowrite8(b, dp->dma_mode);
>> >> +
>> >> + b = atp867x_get_active_clocks_shifted(t.active) |
>> >> + atp867x_get_recover_clocks_shifted(t.recover);
>> >> + if (dp->pci66mhz)
>> >> + b += 0x10;
>> >
>> > What is the purpose of the above hack?
>>
>> For safe PIO mode according to spec.
>>
>> >
>> > AFAICS (I don't have a datasheet) it may result in invalid active
>> > clocks being used for t.active > 12 and 0x80 bit being set incorrectly
>> > for t.active values 7..12 (unless it was the purpose of the hack).
>>
>> See the patch below..
>>
>> >
>> >> + if (adev->devno & 1)
>> >> + iowrite8(b, dp->slave_piospd);
>> >> + else
>> >> + iowrite8(b, dp->mstr_piospd);
>> >> +
>> >> + /*
>> >> + * use the same value for comand timing as for PIO timimg
>> >> + */
>> >> + iowrite8(b, dp->eightb_piospd);
>> >
>> > This is incorrect if slave/master devices use different PIO modes
>> > or if PIO mode <= 2 is used by any device.
>> >
>> > Timing based on t.act8b and t.rec8b values should be used instead.
>>
>> act8b and rec8b have the same values as active, recovery of the port.
>
> Please take a look at drivers/ata/libata-core.c::ata_timing[] table:
>
> ...
> { XFER_PIO_0, 70, 290, 240, 600, 165, 150, 0, 600, 0 },
> { XFER_PIO_1, 50, 290, 93, 383, 125, 100, 0, 383, 0 },
> { XFER_PIO_2, 30, 290, 40, 330, 100, 90, 0, 240, 0 },
> { XFER_PIO_3, 30, 80, 70, 180, 80, 70, 0, 180, 0 },
> { XFER_PIO_4, 25, 70, 25, 120, 70, 25, 0, 120, 0 },
> { XFER_PIO_5, 15, 65, 25, 100, 65, 25, 0, 100, 0 },
> { XFER_PIO_6, 10, 55, 20, 80, 55, 20, 0, 80, 0 },
> ...
>
> For PIO modes <= 2 (or if master/slave devices use different PIO modes)
> we'll have different values, i.e. for PIO2 in case of a single device on
> the port using standard timings we'll have:
>
> t.active = 4
> t.recovery = 4
> t.act8b = 10
> t.rec8b = 2
>
> Most likely we won't see much use of this driver with older devices,
> however this should not stop us from supporting them and at the same
> time making the driver easier to maintain.
>
>> If a:r=3:1 then they become 4:1 on 66mhz for safer transfer, and
>> a8:r8=3:1, which is identical but the a8 should be incremented by 1.
>> I can use a8:r8 with 66mhz fixup but it becomes the same as using a:r.
>> Take a look at the patch below.
>>
>> >
>> > On the somehow related note:
>> >
>> > * I don't see how PIO0-2 command timings can be met with only 3 bits
>> > used for active clocks. Could it be that dp->eight_piospd should be
>> > programmed in a slightly different way than dp->{mstr,slave}_piospd?
>> >
>>
>> See new patch on clocks_shift below.
>>
>> > * The controller allows higher clocks values for recovery timings but
>> > ata_timing_compute() tries to fairly increase both recovery and active
>> > timings to meet the required cycle timing.
>> >
>> >> +}
>> >> +
>> >> +static int atp867x_cable_detect(struct ata_port *ap)
>> >> +{
>> >> + return ATA_CBL_PATA40_SHORT;
>> >> +}
>> >
>> > As noticed by Robert and Alan already:
>> >
>> > This should use ATA_CBL_PATA_UNK and rely on the driver-side cable detection.
>>
>> I modified cable_detect() to use override; on a certain
>> subsystem_vendor|device, its 40short, others, unknown.
>>
>> >
>> >
>> > One last thing: Power Management support is missing from this driver
>> > (I tried addressing this in the separately posted patch but it needs
>> > testing by somebody with the hardware).
>> >
>> >
>> > MWDMA fix:
>> >
>> > From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
>> > Subject: [PATCH] pata_atp867x: fix it to not claim MWDMA support
>> >
>> > MWDMA modes are not supported by this driver currently.
>> >
>> > Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
>> > ---
>> > drivers/ata/pata_atp867x.c | 10 +---------
>> > 1 file changed, 1 insertion(+), 9 deletions(-)
>> >
>> > Index: b/drivers/ata/pata_atp867x.c
>> > ===================================================================
>> > --- a/drivers/ata/pata_atp867x.c
>> > +++ b/drivers/ata/pata_atp867x.c
>> > @@ -118,20 +118,13 @@ struct atp867x_priv {
>> > int pci66mhz;
>> > };
>> >
>> > -static inline u8 atp867x_speed_to_mode(u8 speed)
>> > -{
>> > - return speed - XFER_UDMA_0 + 1;
>> > -}
>> > -
>> > static void atp867x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
>> > {
>> > struct pci_dev *pdev = to_pci_dev(ap->host->dev);
>> > struct atp867x_priv *dp = ap->private_data;
>> > u8 speed = adev->dma_mode;
>> > u8 b;
>> > - u8 mode;
>> > -
>> > - mode = atp867x_speed_to_mode(speed);
>> > + u8 mode = speed - XFER_UDMA_0 + 1;
>> >
>> > /*
>> > * Doc 6.6.9: decrease the udma mode value by 1 for safer UDMA speed
>> > @@ -471,7 +464,6 @@ static int atp867x_init_one(struct pci_d
>> > static const struct ata_port_info info_867x = {
>> > .flags = ATA_FLAG_SLAVE_POSS,
>> > .pio_mask = ATA_PIO4,
>> > - .mwdma_mask = ATA_MWDMA2,
>>
>> This looks good to me. thx.
>>
>> > .udma_mask = ATA_UDMA6,
>> > .port_ops = &atp867x_ops,
>> > };
>> >
>>
>>
>> From: John(Jung-Ik) Lee <jilee@google.com>
>>
>> clarifications in timings calculations and cable detection
>>
>> Signed-off-by: John(Jung-Ik) Lee <jilee@google.com>
>> ---
>>
>> pata_atp867x.c | 50 +++++++++++++++++++++++++++++++++++++-------------
>> 1 files changed, 37 insertions, 13 deletions
>>
>> diff --git a/drivers/ata/pata_atp867x.c b/drivers/ata/pata_atp867x.c
>> index e6c4706..c1c691f 100644
>> --- a/drivers/ata/pata_atp867x.c
>> +++ b/drivers/ata/pata_atp867x.c
>> @@ -156,8 +156,10 @@ static void atp867x_set_dmamode(struct ata_port
>> *ap, struct ata_device *adev)
>> iowrite8(b, dp->dma_mode);
>> }
>>
>> -static int atp867x_get_active_clocks_shifted(unsigned int clk)
>> +static int atp867x_get_active_clocks_shifted(struct ata_port *ap,
>> + unsigned int clk)
>> {
>> + struct atp867x_priv *dp = ap->private_data;
>> unsigned char clocks = clk;
>>
>> switch (clocks) {
>> @@ -166,15 +168,25 @@ static int
>> atp867x_get_active_clocks_shifted(unsigned int clk)
>> break;
>> case 1 ... 7:
>> break;
>> - case 8 ... 12:
>> + case 9 ... 12:
>> clocks = 7;
>> break;
>> default:
>> printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
>> "Using default 8clk.\n", clk);
>> - clocks = 0; /* 8 clk */
>> - break;
>> + case 8: /* default 8 clk */
>> + clocks = 0;
>> + goto active_clock_shift_done;
>> }
>> +
>> + /*
>> + * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
>> + * on 66MHz bus
>> + */
>> + if (dp->pci66mhz && clocks < 7)
>> + clocks++;
>> +
>> +active_clock_shift_done:
>> return clocks << ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
>> }
>>
>> @@ -188,20 +200,19 @@ static int
>> atp867x_get_recover_clocks_shifted(unsigned int clk)
>> break;
>> case 1 ... 11:
>> break;
>> - case 12:
>> - clocks = 0;
>> - break;
>> case 13: case 14:
>> - --clocks;
>> + --clocks; /* by the spec */
>> break;
>> case 15:
>> break;
>> default:
>> printk(KERN_WARNING "ATP867X: recover %dclk is invalid. "
>> "Using default 12clk.\n", clk);
>> - clocks = 0; /* 12 clk */
>> + case 12: /* default 12 clk */
>> + clocks = 0;
>> break;
>> }
>> +
>> return clocks << ATP867X_IO_PIOSPD_RECOVER_SHIFT;
>> }
>>
>> @@ -230,10 +241,8 @@ static void atp867x_set_piomode(struct ata_port
>> *ap, struct ata_device *adev)
>> b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK);
>> iowrite8(b, dp->dma_mode);
>>
>> - b = atp867x_get_active_clocks_shifted(t.active) |
>> + b = atp867x_get_active_clocks_shifted(ap, t.active) |
>> atp867x_get_recover_clocks_shifted(t.recover);
>> - if (dp->pci66mhz)
>> - b += 0x10;
>>
>> if (adev->devno & 1)
>> iowrite8(b, dp->slave_piospd);
>> @@ -246,9 +255,24 @@ static void atp867x_set_piomode(struct ata_port
>> *ap, struct ata_device *adev)
>> iowrite8(b, dp->eightb_piospd);
>> }
>>
>> +static int atp867x_cable_override(struct pci_dev *pdev)
>> +{
>> + if (pdev->subsystem_vendor == PCI_VENDOR_ID_ARTOP &&
>> + (pdev->subsystem_device == PCI_DEVICE_ID_ARTOP_ATP867A ||
>> + pdev->subsystem_device == PCI_DEVICE_ID_ARTOP_ATP867B)) {
>> + return 1;
>> + }
>> + return 0;
>> +}
>> +
>> static int atp867x_cable_detect(struct ata_port *ap)
>> {
>> - return ATA_CBL_PATA40_SHORT;
>> + struct pci_dev *pdev = to_pci_dev(ap->host->dev);
>> +
>> + if (atp867x_cable_override(pdev))
>> + return ATA_CBL_PATA40_SHORT;
>> +
>> + return ATA_CBL_PATA_UNK;
>> }
>>
>> static struct scsi_host_template atp867x_sht = {
>
> Thanks, your patch looks good to me but since there are still some
> leftover issues left we would also need something like the incremental
> patch below:
[resending - bounced back from -ide, -kernel]
your patch below looks good to me.
-John
>
> From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Subject: [PATCH] pata_atp867x: PIO support fixes
>
> * use 8 clk setting for active clocks == 7 (was 12 clk)
> * use 12 clk setting for active clocks > 12 (was 8 clk)
> * do 66MHz bus fixup before mapping active clocks
> * fix setup of PIO command timings
>
> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> ---
> drivers/ata/pata_atp867x.c | 36 +++++++++++++++++++-----------------
> 1 file changed, 19 insertions(+), 17 deletions(-)
>
> Index: b/drivers/ata/pata_atp867x.c
> ===================================================================
> --- a/drivers/ata/pata_atp867x.c
> +++ b/drivers/ata/pata_atp867x.c
> @@ -155,30 +155,31 @@ static int atp867x_get_active_clocks_shi
> struct atp867x_priv *dp = ap->private_data;
> unsigned char clocks = clk;
>
> + /*
> + * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
> + * on 66MHz bus
> + */
> + if (dp->pci66mhz)
> + clocks++;
> +
> switch (clocks) {
> case 0:
> clocks = 1;
> break;
> - case 1 ... 7:
> - break;
> - case 9 ... 12:
> - clocks = 7;
> + case 1 ... 6:
> break;
> default:
> printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
> - "Using default 8clk.\n", clk);
> + "Using 12clk.\n", clk);
> + case 9 ... 12:
> + clocks = 7; /* 12 clk */
> + break;
> + case 7:
> case 8: /* default 8 clk */
> clocks = 0;
> goto active_clock_shift_done;
> }
>
> - /*
> - * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
> - * on 66MHz bus
> - */
> - if (dp->pci66mhz && clocks < 7)
> - clocks++;
> -
> active_clock_shift_done:
> return clocks << ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
> }
> @@ -193,7 +194,8 @@ static int atp867x_get_recover_clocks_sh
> break;
> case 1 ... 11:
> break;
> - case 13: case 14:
> + case 13:
> + case 14:
> --clocks; /* by the spec */
> break;
> case 15:
> @@ -235,16 +237,16 @@ static void atp867x_set_piomode(struct a
> iowrite8(b, dp->dma_mode);
>
> b = atp867x_get_active_clocks_shifted(ap, t.active) |
> - atp867x_get_recover_clocks_shifted(t.recover);
> + atp867x_get_recover_clocks_shifted(t.recover);
>
> if (adev->devno & 1)
> iowrite8(b, dp->slave_piospd);
> else
> iowrite8(b, dp->mstr_piospd);
>
> - /*
> - * use the same value for comand timing as for PIO timimg
> - */
> + b = atp867x_get_active_clocks_shifted(ap, t.act8b) |
> + atp867x_get_recover_clocks_shifted(t.rec8b);
> +
> iowrite8(b, dp->eightb_piospd);
> }
>
>
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2009-09-22 2:36 ` Jung-Ik (John) Lee
@ 2009-09-28 15:34 ` Bartlomiej Zolnierkiewicz
2009-09-28 20:20 ` Jung-Ik (John) Lee
` (2 more replies)
0 siblings, 3 replies; 95+ messages in thread
From: Bartlomiej Zolnierkiewicz @ 2009-09-28 15:34 UTC (permalink / raw)
To: Jung-Ik (John) Lee
Cc: Jeff Garzik, Andrew Morton, Linus Torvalds, linux-ide, LKML,
Grant Grundler, Gwendal Gringo
On Tuesday 22 September 2009 04:36:13 Jung-Ik (John) Lee wrote:
> On Sun, Sep 20, 2009 at 2:05 PM, Bartlomiej Zolnierkiewicz
> <bzolnier@gmail.com> wrote:
> > On Thursday 17 September 2009 22:49:35 Jeff Garzik wrote:
> >>
> >> Bug fixes, and a new driver.
> >>
> >>
> >>
> >> Please pull from 'upstream-linus' branch of
> >> master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
> >>
> >> to receive the following updates:
> >>
> >> drivers/ata/Kconfig | 9 +
> >> drivers/ata/Makefile | 1 +
> >> drivers/ata/ahci.c | 4 +-
> >> drivers/ata/libata-core.c | 4 +-
> >> drivers/ata/pata_amd.c | 3 +
> >> drivers/ata/pata_atp867x.c | 548 ++++++++++++++++++++++++++++++++++++++++++++
> >> drivers/ata/sata_promise.c | 155 +++++++++++--
> >> include/linux/pci_ids.h | 2 +
> >> 8 files changed, 704 insertions(+), 22 deletions(-)
> >> create mode 100644 drivers/ata/pata_atp867x.c
> >>
> >> John(Jung-Ik) Lee (1):
> >> libata: Add pata_atp867x driver for Artop/Acard ATP867X controllers
> >
> > That was really fast.. Not necessarily a bad thing but this driver would
> > benefit from few polishing touches..
> >
> >> diff --git a/drivers/ata/pata_atp867x.c b/drivers/ata/pata_atp867x.c
> >> new file mode 100644
> >> index 0000000..7990de9
> >> --- /dev/null
> >> +++ b/drivers/ata/pata_atp867x.c
> >> @@ -0,0 +1,548 @@
> >> +/*
> >> + * pata_atp867x.c - ARTOP 867X 64bit 4-channel UDMA133 ATA controller driver
> >> + *
> >> + * (C) 2009 Google Inc. John(Jung-Ik) Lee <jilee@google.com>
> >> + *
> >> + * Per Atp867 data sheet rev 1.2, Acard.
> >> + * Based in part on early ide code from
> >> + * 2003-2004 by Eric Uhrhane, Google, Inc.
> >> + *
> >> + * This program is free software; you can redistribute it and/or modify
> >> + * it under the terms of the GNU General Public License as published by
> >> + * the Free Software Foundation; either version 2 of the License, or
> >> + * (at your option) any later version.
> >> + *
> >> + * This program is distributed in the hope that it will be useful,
> >> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> >> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> >> + * GNU General Public License for more details.
> >> + *
> >> + * You should have received a copy of the GNU General Public License
> >> + * along with this program; if not, write to the Free Software
> >> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
> >> + *
> >> + *
> >> + * TODO:
> >> + * 1. RAID features [comparison, XOR, striping, mirroring, etc.]
> >> + */
> >> +
> >> +#include <linux/kernel.h>
> >> +#include <linux/module.h>
> >> +#include <linux/pci.h>
> >> +#include <linux/init.h>
> >> +#include <linux/blkdev.h>
> >> +#include <linux/delay.h>
> >> +#include <linux/device.h>
> >> +#include <scsi/scsi_host.h>
> >> +#include <linux/libata.h>
> >> +
> >> +#define DRV_NAME "pata_atp867x"
> >> +#define DRV_VERSION "0.7.5"
> >> +
> >> +/*
> >> + * IO Registers
> >> + * Note that all runtime hot priv ports are cached in ap private_data
> >> + */
> >> +
> >> +enum {
> >> + ATP867X_IO_CHANNEL_OFFSET = 0x10,
> >> +
> >> + /*
> >> + * IO Register Bitfields
> >> + */
> >> +
> >> + ATP867X_IO_PIOSPD_ACTIVE_SHIFT = 4,
> >> + ATP867X_IO_PIOSPD_RECOVER_SHIFT = 0,
> >> +
> >> + ATP867X_IO_DMAMODE_MSTR_SHIFT = 0,
> >> + ATP867X_IO_DMAMODE_MSTR_MASK = 0x07,
> >> + ATP867X_IO_DMAMODE_SLAVE_SHIFT = 4,
> >> + ATP867X_IO_DMAMODE_SLAVE_MASK = 0x70,
> >> +
> >> + ATP867X_IO_DMAMODE_UDMA_6 = 0x07,
> >> + ATP867X_IO_DMAMODE_UDMA_5 = 0x06,
> >> + ATP867X_IO_DMAMODE_UDMA_4 = 0x05,
> >> + ATP867X_IO_DMAMODE_UDMA_3 = 0x04,
> >> + ATP867X_IO_DMAMODE_UDMA_2 = 0x03,
> >> + ATP867X_IO_DMAMODE_UDMA_1 = 0x02,
> >> + ATP867X_IO_DMAMODE_UDMA_0 = 0x01,
> >> + ATP867X_IO_DMAMODE_DISABLE = 0x00,
> >> +
> >> + ATP867X_IO_SYS_INFO_66MHZ = 0x04,
> >> + ATP867X_IO_SYS_INFO_SLOW_UDMA5 = 0x02,
> >> + ATP867X_IO_SYS_MASK_RESERVED = (~0xf1),
> >> +
> >> + ATP867X_IO_PORTSPD_VAL = 0x1143,
> >> + ATP867X_PREREAD_VAL = 0x0200,
> >> +
> >> + ATP867X_NUM_PORTS = 4,
> >> + ATP867X_BAR_IOBASE = 0,
> >> + ATP867X_BAR_ROMBASE = 6,
> >> +};
> >> +
> >> +#define ATP867X_IOBASE(ap) ((ap)->host->iomap[0])
> >> +#define ATP867X_SYS_INFO(ap) (0x3F + ATP867X_IOBASE(ap))
> >> +
> >> +#define ATP867X_IO_PORTBASE(ap, port) (0x00 + ATP867X_IOBASE(ap) + \
> >> + (port) * ATP867X_IO_CHANNEL_OFFSET)
> >> +#define ATP867X_IO_DMABASE(ap, port) (0x40 + \
> >> + ATP867X_IO_PORTBASE((ap), (port)))
> >> +
> >> +#define ATP867X_IO_STATUS(ap, port) (0x07 + \
> >> + ATP867X_IO_PORTBASE((ap), (port)))
> >> +#define ATP867X_IO_ALTSTATUS(ap, port) (0x0E + \
> >> + ATP867X_IO_PORTBASE((ap), (port)))
> >> +
> >> +/*
> >> + * hot priv ports
> >> + */
> >> +#define ATP867X_IO_MSTRPIOSPD(ap, port) (0x08 + \
> >> + ATP867X_IO_DMABASE((ap), (port)))
> >> +#define ATP867X_IO_SLAVPIOSPD(ap, port) (0x09 + \
> >> + ATP867X_IO_DMABASE((ap), (port)))
> >> +#define ATP867X_IO_8BPIOSPD(ap, port) (0x0A + \
> >> + ATP867X_IO_DMABASE((ap), (port)))
> >> +#define ATP867X_IO_DMAMODE(ap, port) (0x0B + \
> >> + ATP867X_IO_DMABASE((ap), (port)))
> >> +
> >> +#define ATP867X_IO_PORTSPD(ap, port) (0x4A + \
> >> + ATP867X_IO_PORTBASE((ap), (port)))
> >> +#define ATP867X_IO_PREREAD(ap, port) (0x4C + \
> >> + ATP867X_IO_PORTBASE((ap), (port)))
> >> +
> >> +struct atp867x_priv {
> >> + void __iomem *dma_mode;
> >> + void __iomem *mstr_piospd;
> >> + void __iomem *slave_piospd;
> >> + void __iomem *eightb_piospd;
> >> + int pci66mhz;
> >> +};
> >> +
> >> +static inline u8 atp867x_speed_to_mode(u8 speed)
> >> +{
> >> + return speed - XFER_UDMA_0 + 1;
> >> +}
> >> +
> >> +static void atp867x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
> >> +{
> >> + struct pci_dev *pdev = to_pci_dev(ap->host->dev);
> >> + struct atp867x_priv *dp = ap->private_data;
> >> + u8 speed = adev->dma_mode;
> >> + u8 b;
> >> + u8 mode;
> >> +
> >> + mode = atp867x_speed_to_mode(speed);
> >
> > The driver currently doesn't support MWDMA modes but claims otherwise
> > (fixed in the attached patch).
> >
> >> + /*
> >> + * Doc 6.6.9: decrease the udma mode value by 1 for safer UDMA speed
> >> + * on 66MHz bus
> >> + * rev-A: UDMA_1~4 (5, 6 no change)
> >> + * rev-B: all UDMA modes
> >> + * UDMA_0 stays not to disable UDMA
> >> + */
> >> + if (dp->pci66mhz && mode > ATP867X_IO_DMAMODE_UDMA_0 &&
> >> + (pdev->device == PCI_DEVICE_ID_ARTOP_ATP867B ||
> >> + mode < ATP867X_IO_DMAMODE_UDMA_5))
> >> + mode--;
> >> +
> >> + b = ioread8(dp->dma_mode);
> >> + if (adev->devno & 1) {
> >> + b = (b & ~ATP867X_IO_DMAMODE_SLAVE_MASK) |
> >> + (mode << ATP867X_IO_DMAMODE_SLAVE_SHIFT);
> >> + } else {
> >> + b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK) |
> >> + (mode << ATP867X_IO_DMAMODE_MSTR_SHIFT);
> >> + }
> >> + iowrite8(b, dp->dma_mode);
> >> +}
> >> +
> >> +static int atp867x_get_active_clocks_shifted(unsigned int clk)
> >> +{
> >> + unsigned char clocks = clk;
> >> +
> >> + switch (clocks) {
> >> + case 0:
> >> + clocks = 1;
> >> + break;
> >> + case 1 ... 7:
> >> + break;
> >> + case 8 ... 12:
> >> + clocks = 7;
> >
> > Shouldn't "clocks = 0" (the default case) be used here?
>
> The clocks value 0 sets it to 8 clocks, while value 7 sets to 12 clocks.
This would explain it but then there is no need to use "clocks = 7"
for the _input_ "clocks == 7".
> I cleaned up a bit on clocks_shift. See the patch below.
>
> > Otherwise it seems to result in underclocked timings for dp->pci66mhz == 0.
> >
> >> + break;
> >> + default:
> >> + printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
> >> + "Using default 8clk.\n", clk);
> >> + clocks = 0; /* 8 clk */
> >> + break;
> >> + }
> >> + return clocks << ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
> >> +}
> >> +
> >> +static int atp867x_get_recover_clocks_shifted(unsigned int clk)
> >> +{
> >> + unsigned char clocks = clk;
> >> +
> >> + switch (clocks) {
> >> + case 0:
> >> + clocks = 1;
> >> + break;
> >> + case 1 ... 11:
> >> + break;
> >> + case 12:
> >> + clocks = 0;
> >> + break;
> >> + case 13: case 14:
> >> + --clocks;
> >> + break;
> >
> > Is "clocks == 14" a reserved setting?
>
> 12 is reserved for the default (== 0), and 13, 14 are set to value 12,
> 13 respectively.
I meant the _output_ "clocks == 14" here.
> >
> > If so a comment documenting it would be appreciated.
>
> Sure. see the new patch below.
>
> >
> >> + case 15:
> >> + break;
> >> + default:
> >> + printk(KERN_WARNING "ATP867X: recover %dclk is invalid. "
> >> + "Using default 15clk.\n", clk);
> >> + clocks = 0; /* 12 clk */
> >
> > Shouldn't it use "clocks == 15" setting?
> It was a typo. 12 is the right default.
>
> >
> >> + break;
> >> + }
> >> + return clocks << ATP867X_IO_PIOSPD_RECOVER_SHIFT;
> >> +}
> >> +
> >> +static void atp867x_set_piomode(struct ata_port *ap, struct ata_device *adev)
> >> +{
> >> + struct ata_device *peer = ata_dev_pair(adev);
> >> + struct atp867x_priv *dp = ap->private_data;
> >> + u8 speed = adev->pio_mode;
> >> + struct ata_timing t, p;
> >> + int T, UT;
> >> + u8 b;
> >> +
> >> + T = 1000000000 / 33333;
> >> + UT = T / 4;
> >> +
> >> + ata_timing_compute(adev, speed, &t, T, UT);
> >> + if (peer && peer->pio_mode) {
> >> + ata_timing_compute(peer, peer->pio_mode, &p, T, UT);
> >> + ata_timing_merge(&p, &t, &t, ATA_TIMING_8BIT);
> >> + }
> >> +
> >> + b = ioread8(dp->dma_mode);
> >> + if (adev->devno & 1)
> >> + b = (b & ~ATP867X_IO_DMAMODE_SLAVE_MASK);
> >> + else
> >> + b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK);
> >> + iowrite8(b, dp->dma_mode);
> >> +
> >> + b = atp867x_get_active_clocks_shifted(t.active) |
> >> + atp867x_get_recover_clocks_shifted(t.recover);
> >> + if (dp->pci66mhz)
> >> + b += 0x10;
> >
> > What is the purpose of the above hack?
>
> For safe PIO mode according to spec.
>
> >
> > AFAICS (I don't have a datasheet) it may result in invalid active
> > clocks being used for t.active > 12 and 0x80 bit being set incorrectly
> > for t.active values 7..12 (unless it was the purpose of the hack).
>
> See the patch below..
>
> >
> >> + if (adev->devno & 1)
> >> + iowrite8(b, dp->slave_piospd);
> >> + else
> >> + iowrite8(b, dp->mstr_piospd);
> >> +
> >> + /*
> >> + * use the same value for comand timing as for PIO timimg
> >> + */
> >> + iowrite8(b, dp->eightb_piospd);
> >
> > This is incorrect if slave/master devices use different PIO modes
> > or if PIO mode <= 2 is used by any device.
> >
> > Timing based on t.act8b and t.rec8b values should be used instead.
>
> act8b and rec8b have the same values as active, recovery of the port.
Please take a look at drivers/ata/libata-core.c::ata_timing[] table:
...
{ XFER_PIO_0, 70, 290, 240, 600, 165, 150, 0, 600, 0 },
{ XFER_PIO_1, 50, 290, 93, 383, 125, 100, 0, 383, 0 },
{ XFER_PIO_2, 30, 290, 40, 330, 100, 90, 0, 240, 0 },
{ XFER_PIO_3, 30, 80, 70, 180, 80, 70, 0, 180, 0 },
{ XFER_PIO_4, 25, 70, 25, 120, 70, 25, 0, 120, 0 },
{ XFER_PIO_5, 15, 65, 25, 100, 65, 25, 0, 100, 0 },
{ XFER_PIO_6, 10, 55, 20, 80, 55, 20, 0, 80, 0 },
...
For PIO modes <= 2 (or if master/slave devices use different PIO modes)
we'll have different values, i.e. for PIO2 in case of a single device on
the port using standard timings we'll have:
t.active = 4
t.recovery = 4
t.act8b = 10
t.rec8b = 2
Most likely we won't see much use of this driver with older devices,
however this should not stop us from supporting them and at the same
time making the driver easier to maintain.
> If a:r=3:1 then they become 4:1 on 66mhz for safer transfer, and
> a8:r8=3:1, which is identical but the a8 should be incremented by 1.
> I can use a8:r8 with 66mhz fixup but it becomes the same as using a:r.
> Take a look at the patch below.
>
> >
> > On the somehow related note:
> >
> > * I don't see how PIO0-2 command timings can be met with only 3 bits
> > used for active clocks. Could it be that dp->eight_piospd should be
> > programmed in a slightly different way than dp->{mstr,slave}_piospd?
> >
>
> See new patch on clocks_shift below.
>
> > * The controller allows higher clocks values for recovery timings but
> > ata_timing_compute() tries to fairly increase both recovery and active
> > timings to meet the required cycle timing.
> >
> >> +}
> >> +
> >> +static int atp867x_cable_detect(struct ata_port *ap)
> >> +{
> >> + return ATA_CBL_PATA40_SHORT;
> >> +}
> >
> > As noticed by Robert and Alan already:
> >
> > This should use ATA_CBL_PATA_UNK and rely on the driver-side cable detection.
>
> I modified cable_detect() to use override; on a certain
> subsystem_vendor|device, its 40short, others, unknown.
>
> >
> >
> > One last thing: Power Management support is missing from this driver
> > (I tried addressing this in the separately posted patch but it needs
> > testing by somebody with the hardware).
> >
> >
> > MWDMA fix:
> >
> > From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> > Subject: [PATCH] pata_atp867x: fix it to not claim MWDMA support
> >
> > MWDMA modes are not supported by this driver currently.
> >
> > Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> > ---
> > drivers/ata/pata_atp867x.c | 10 +---------
> > 1 file changed, 1 insertion(+), 9 deletions(-)
> >
> > Index: b/drivers/ata/pata_atp867x.c
> > ===================================================================
> > --- a/drivers/ata/pata_atp867x.c
> > +++ b/drivers/ata/pata_atp867x.c
> > @@ -118,20 +118,13 @@ struct atp867x_priv {
> > int pci66mhz;
> > };
> >
> > -static inline u8 atp867x_speed_to_mode(u8 speed)
> > -{
> > - return speed - XFER_UDMA_0 + 1;
> > -}
> > -
> > static void atp867x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
> > {
> > struct pci_dev *pdev = to_pci_dev(ap->host->dev);
> > struct atp867x_priv *dp = ap->private_data;
> > u8 speed = adev->dma_mode;
> > u8 b;
> > - u8 mode;
> > -
> > - mode = atp867x_speed_to_mode(speed);
> > + u8 mode = speed - XFER_UDMA_0 + 1;
> >
> > /*
> > * Doc 6.6.9: decrease the udma mode value by 1 for safer UDMA speed
> > @@ -471,7 +464,6 @@ static int atp867x_init_one(struct pci_d
> > static const struct ata_port_info info_867x = {
> > .flags = ATA_FLAG_SLAVE_POSS,
> > .pio_mask = ATA_PIO4,
> > - .mwdma_mask = ATA_MWDMA2,
>
> This looks good to me. thx.
>
> > .udma_mask = ATA_UDMA6,
> > .port_ops = &atp867x_ops,
> > };
> >
>
>
> From: John(Jung-Ik) Lee <jilee@google.com>
>
> clarifications in timings calculations and cable detection
>
> Signed-off-by: John(Jung-Ik) Lee <jilee@google.com>
> ---
>
> pata_atp867x.c | 50 +++++++++++++++++++++++++++++++++++++-------------
> 1 files changed, 37 insertions, 13 deletions
>
> diff --git a/drivers/ata/pata_atp867x.c b/drivers/ata/pata_atp867x.c
> index e6c4706..c1c691f 100644
> --- a/drivers/ata/pata_atp867x.c
> +++ b/drivers/ata/pata_atp867x.c
> @@ -156,8 +156,10 @@ static void atp867x_set_dmamode(struct ata_port
> *ap, struct ata_device *adev)
> iowrite8(b, dp->dma_mode);
> }
>
> -static int atp867x_get_active_clocks_shifted(unsigned int clk)
> +static int atp867x_get_active_clocks_shifted(struct ata_port *ap,
> + unsigned int clk)
> {
> + struct atp867x_priv *dp = ap->private_data;
> unsigned char clocks = clk;
>
> switch (clocks) {
> @@ -166,15 +168,25 @@ static int
> atp867x_get_active_clocks_shifted(unsigned int clk)
> break;
> case 1 ... 7:
> break;
> - case 8 ... 12:
> + case 9 ... 12:
> clocks = 7;
> break;
> default:
> printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
> "Using default 8clk.\n", clk);
> - clocks = 0; /* 8 clk */
> - break;
> + case 8: /* default 8 clk */
> + clocks = 0;
> + goto active_clock_shift_done;
> }
> +
> + /*
> + * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
> + * on 66MHz bus
> + */
> + if (dp->pci66mhz && clocks < 7)
> + clocks++;
> +
> +active_clock_shift_done:
> return clocks << ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
> }
>
> @@ -188,20 +200,19 @@ static int
> atp867x_get_recover_clocks_shifted(unsigned int clk)
> break;
> case 1 ... 11:
> break;
> - case 12:
> - clocks = 0;
> - break;
> case 13: case 14:
> - --clocks;
> + --clocks; /* by the spec */
> break;
> case 15:
> break;
> default:
> printk(KERN_WARNING "ATP867X: recover %dclk is invalid. "
> "Using default 12clk.\n", clk);
> - clocks = 0; /* 12 clk */
> + case 12: /* default 12 clk */
> + clocks = 0;
> break;
> }
> +
> return clocks << ATP867X_IO_PIOSPD_RECOVER_SHIFT;
> }
>
> @@ -230,10 +241,8 @@ static void atp867x_set_piomode(struct ata_port
> *ap, struct ata_device *adev)
> b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK);
> iowrite8(b, dp->dma_mode);
>
> - b = atp867x_get_active_clocks_shifted(t.active) |
> + b = atp867x_get_active_clocks_shifted(ap, t.active) |
> atp867x_get_recover_clocks_shifted(t.recover);
> - if (dp->pci66mhz)
> - b += 0x10;
>
> if (adev->devno & 1)
> iowrite8(b, dp->slave_piospd);
> @@ -246,9 +255,24 @@ static void atp867x_set_piomode(struct ata_port
> *ap, struct ata_device *adev)
> iowrite8(b, dp->eightb_piospd);
> }
>
> +static int atp867x_cable_override(struct pci_dev *pdev)
> +{
> + if (pdev->subsystem_vendor == PCI_VENDOR_ID_ARTOP &&
> + (pdev->subsystem_device == PCI_DEVICE_ID_ARTOP_ATP867A ||
> + pdev->subsystem_device == PCI_DEVICE_ID_ARTOP_ATP867B)) {
> + return 1;
> + }
> + return 0;
> +}
> +
> static int atp867x_cable_detect(struct ata_port *ap)
> {
> - return ATA_CBL_PATA40_SHORT;
> + struct pci_dev *pdev = to_pci_dev(ap->host->dev);
> +
> + if (atp867x_cable_override(pdev))
> + return ATA_CBL_PATA40_SHORT;
> +
> + return ATA_CBL_PATA_UNK;
> }
>
> static struct scsi_host_template atp867x_sht = {
Thanks, your patch looks good to me but since there are still some
leftover issues left we would also need something like the incremental
patch below:
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Subject: [PATCH] pata_atp867x: PIO support fixes
* use 8 clk setting for active clocks == 7 (was 12 clk)
* use 12 clk setting for active clocks > 12 (was 8 clk)
* do 66MHz bus fixup before mapping active clocks
* fix setup of PIO command timings
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
drivers/ata/pata_atp867x.c | 36 +++++++++++++++++++-----------------
1 file changed, 19 insertions(+), 17 deletions(-)
Index: b/drivers/ata/pata_atp867x.c
===================================================================
--- a/drivers/ata/pata_atp867x.c
+++ b/drivers/ata/pata_atp867x.c
@@ -155,30 +155,31 @@ static int atp867x_get_active_clocks_shi
struct atp867x_priv *dp = ap->private_data;
unsigned char clocks = clk;
+ /*
+ * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
+ * on 66MHz bus
+ */
+ if (dp->pci66mhz)
+ clocks++;
+
switch (clocks) {
case 0:
clocks = 1;
break;
- case 1 ... 7:
- break;
- case 9 ... 12:
- clocks = 7;
+ case 1 ... 6:
break;
default:
printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
- "Using default 8clk.\n", clk);
+ "Using 12clk.\n", clk);
+ case 9 ... 12:
+ clocks = 7; /* 12 clk */
+ break;
+ case 7:
case 8: /* default 8 clk */
clocks = 0;
goto active_clock_shift_done;
}
- /*
- * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
- * on 66MHz bus
- */
- if (dp->pci66mhz && clocks < 7)
- clocks++;
-
active_clock_shift_done:
return clocks << ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
}
@@ -193,7 +194,8 @@ static int atp867x_get_recover_clocks_sh
break;
case 1 ... 11:
break;
- case 13: case 14:
+ case 13:
+ case 14:
--clocks; /* by the spec */
break;
case 15:
@@ -235,16 +237,16 @@ static void atp867x_set_piomode(struct a
iowrite8(b, dp->dma_mode);
b = atp867x_get_active_clocks_shifted(ap, t.active) |
- atp867x_get_recover_clocks_shifted(t.recover);
+ atp867x_get_recover_clocks_shifted(t.recover);
if (adev->devno & 1)
iowrite8(b, dp->slave_piospd);
else
iowrite8(b, dp->mstr_piospd);
- /*
- * use the same value for comand timing as for PIO timimg
- */
+ b = atp867x_get_active_clocks_shifted(ap, t.act8b) |
+ atp867x_get_recover_clocks_shifted(t.rec8b);
+
iowrite8(b, dp->eightb_piospd);
}
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2009-09-20 21:05 ` Bartlomiej Zolnierkiewicz
@ 2009-09-22 2:36 ` Jung-Ik (John) Lee
2009-09-28 15:34 ` Bartlomiej Zolnierkiewicz
0 siblings, 1 reply; 95+ messages in thread
From: Jung-Ik (John) Lee @ 2009-09-22 2:36 UTC (permalink / raw)
To: Bartlomiej Zolnierkiewicz
Cc: Jeff Garzik, Andrew Morton, Linus Torvalds, linux-ide, LKML,
Grant Grundler, Gwendal Gringo
On Sun, Sep 20, 2009 at 2:05 PM, Bartlomiej Zolnierkiewicz
<bzolnier@gmail.com> wrote:
> On Thursday 17 September 2009 22:49:35 Jeff Garzik wrote:
>>
>> Bug fixes, and a new driver.
>>
>>
>>
>> Please pull from 'upstream-linus' branch of
>> master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
>>
>> to receive the following updates:
>>
>> drivers/ata/Kconfig | 9 +
>> drivers/ata/Makefile | 1 +
>> drivers/ata/ahci.c | 4 +-
>> drivers/ata/libata-core.c | 4 +-
>> drivers/ata/pata_amd.c | 3 +
>> drivers/ata/pata_atp867x.c | 548 ++++++++++++++++++++++++++++++++++++++++++++
>> drivers/ata/sata_promise.c | 155 +++++++++++--
>> include/linux/pci_ids.h | 2 +
>> 8 files changed, 704 insertions(+), 22 deletions(-)
>> create mode 100644 drivers/ata/pata_atp867x.c
>>
>> John(Jung-Ik) Lee (1):
>> libata: Add pata_atp867x driver for Artop/Acard ATP867X controllers
>
> That was really fast.. Not necessarily a bad thing but this driver would
> benefit from few polishing touches..
>
>> diff --git a/drivers/ata/pata_atp867x.c b/drivers/ata/pata_atp867x.c
>> new file mode 100644
>> index 0000000..7990de9
>> --- /dev/null
>> +++ b/drivers/ata/pata_atp867x.c
>> @@ -0,0 +1,548 @@
>> +/*
>> + * pata_atp867x.c - ARTOP 867X 64bit 4-channel UDMA133 ATA controller driver
>> + *
>> + * (C) 2009 Google Inc. John(Jung-Ik) Lee <jilee@google.com>
>> + *
>> + * Per Atp867 data sheet rev 1.2, Acard.
>> + * Based in part on early ide code from
>> + * 2003-2004 by Eric Uhrhane, Google, Inc.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; either version 2 of the License, or
>> + * (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program; if not, write to the Free Software
>> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
>> + *
>> + *
>> + * TODO:
>> + * 1. RAID features [comparison, XOR, striping, mirroring, etc.]
>> + */
>> +
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/pci.h>
>> +#include <linux/init.h>
>> +#include <linux/blkdev.h>
>> +#include <linux/delay.h>
>> +#include <linux/device.h>
>> +#include <scsi/scsi_host.h>
>> +#include <linux/libata.h>
>> +
>> +#define DRV_NAME "pata_atp867x"
>> +#define DRV_VERSION "0.7.5"
>> +
>> +/*
>> + * IO Registers
>> + * Note that all runtime hot priv ports are cached in ap private_data
>> + */
>> +
>> +enum {
>> + ATP867X_IO_CHANNEL_OFFSET = 0x10,
>> +
>> + /*
>> + * IO Register Bitfields
>> + */
>> +
>> + ATP867X_IO_PIOSPD_ACTIVE_SHIFT = 4,
>> + ATP867X_IO_PIOSPD_RECOVER_SHIFT = 0,
>> +
>> + ATP867X_IO_DMAMODE_MSTR_SHIFT = 0,
>> + ATP867X_IO_DMAMODE_MSTR_MASK = 0x07,
>> + ATP867X_IO_DMAMODE_SLAVE_SHIFT = 4,
>> + ATP867X_IO_DMAMODE_SLAVE_MASK = 0x70,
>> +
>> + ATP867X_IO_DMAMODE_UDMA_6 = 0x07,
>> + ATP867X_IO_DMAMODE_UDMA_5 = 0x06,
>> + ATP867X_IO_DMAMODE_UDMA_4 = 0x05,
>> + ATP867X_IO_DMAMODE_UDMA_3 = 0x04,
>> + ATP867X_IO_DMAMODE_UDMA_2 = 0x03,
>> + ATP867X_IO_DMAMODE_UDMA_1 = 0x02,
>> + ATP867X_IO_DMAMODE_UDMA_0 = 0x01,
>> + ATP867X_IO_DMAMODE_DISABLE = 0x00,
>> +
>> + ATP867X_IO_SYS_INFO_66MHZ = 0x04,
>> + ATP867X_IO_SYS_INFO_SLOW_UDMA5 = 0x02,
>> + ATP867X_IO_SYS_MASK_RESERVED = (~0xf1),
>> +
>> + ATP867X_IO_PORTSPD_VAL = 0x1143,
>> + ATP867X_PREREAD_VAL = 0x0200,
>> +
>> + ATP867X_NUM_PORTS = 4,
>> + ATP867X_BAR_IOBASE = 0,
>> + ATP867X_BAR_ROMBASE = 6,
>> +};
>> +
>> +#define ATP867X_IOBASE(ap) ((ap)->host->iomap[0])
>> +#define ATP867X_SYS_INFO(ap) (0x3F + ATP867X_IOBASE(ap))
>> +
>> +#define ATP867X_IO_PORTBASE(ap, port) (0x00 + ATP867X_IOBASE(ap) + \
>> + (port) * ATP867X_IO_CHANNEL_OFFSET)
>> +#define ATP867X_IO_DMABASE(ap, port) (0x40 + \
>> + ATP867X_IO_PORTBASE((ap), (port)))
>> +
>> +#define ATP867X_IO_STATUS(ap, port) (0x07 + \
>> + ATP867X_IO_PORTBASE((ap), (port)))
>> +#define ATP867X_IO_ALTSTATUS(ap, port) (0x0E + \
>> + ATP867X_IO_PORTBASE((ap), (port)))
>> +
>> +/*
>> + * hot priv ports
>> + */
>> +#define ATP867X_IO_MSTRPIOSPD(ap, port) (0x08 + \
>> + ATP867X_IO_DMABASE((ap), (port)))
>> +#define ATP867X_IO_SLAVPIOSPD(ap, port) (0x09 + \
>> + ATP867X_IO_DMABASE((ap), (port)))
>> +#define ATP867X_IO_8BPIOSPD(ap, port) (0x0A + \
>> + ATP867X_IO_DMABASE((ap), (port)))
>> +#define ATP867X_IO_DMAMODE(ap, port) (0x0B + \
>> + ATP867X_IO_DMABASE((ap), (port)))
>> +
>> +#define ATP867X_IO_PORTSPD(ap, port) (0x4A + \
>> + ATP867X_IO_PORTBASE((ap), (port)))
>> +#define ATP867X_IO_PREREAD(ap, port) (0x4C + \
>> + ATP867X_IO_PORTBASE((ap), (port)))
>> +
>> +struct atp867x_priv {
>> + void __iomem *dma_mode;
>> + void __iomem *mstr_piospd;
>> + void __iomem *slave_piospd;
>> + void __iomem *eightb_piospd;
>> + int pci66mhz;
>> +};
>> +
>> +static inline u8 atp867x_speed_to_mode(u8 speed)
>> +{
>> + return speed - XFER_UDMA_0 + 1;
>> +}
>> +
>> +static void atp867x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
>> +{
>> + struct pci_dev *pdev = to_pci_dev(ap->host->dev);
>> + struct atp867x_priv *dp = ap->private_data;
>> + u8 speed = adev->dma_mode;
>> + u8 b;
>> + u8 mode;
>> +
>> + mode = atp867x_speed_to_mode(speed);
>
> The driver currently doesn't support MWDMA modes but claims otherwise
> (fixed in the attached patch).
>
>> + /*
>> + * Doc 6.6.9: decrease the udma mode value by 1 for safer UDMA speed
>> + * on 66MHz bus
>> + * rev-A: UDMA_1~4 (5, 6 no change)
>> + * rev-B: all UDMA modes
>> + * UDMA_0 stays not to disable UDMA
>> + */
>> + if (dp->pci66mhz && mode > ATP867X_IO_DMAMODE_UDMA_0 &&
>> + (pdev->device == PCI_DEVICE_ID_ARTOP_ATP867B ||
>> + mode < ATP867X_IO_DMAMODE_UDMA_5))
>> + mode--;
>> +
>> + b = ioread8(dp->dma_mode);
>> + if (adev->devno & 1) {
>> + b = (b & ~ATP867X_IO_DMAMODE_SLAVE_MASK) |
>> + (mode << ATP867X_IO_DMAMODE_SLAVE_SHIFT);
>> + } else {
>> + b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK) |
>> + (mode << ATP867X_IO_DMAMODE_MSTR_SHIFT);
>> + }
>> + iowrite8(b, dp->dma_mode);
>> +}
>> +
>> +static int atp867x_get_active_clocks_shifted(unsigned int clk)
>> +{
>> + unsigned char clocks = clk;
>> +
>> + switch (clocks) {
>> + case 0:
>> + clocks = 1;
>> + break;
>> + case 1 ... 7:
>> + break;
>> + case 8 ... 12:
>> + clocks = 7;
>
> Shouldn't "clocks = 0" (the default case) be used here?
The clocks value 0 sets it to 8 clocks, while value 7 sets to 12 clocks.
I cleaned up a bit on clocks_shift. See the patch below.
>
> Otherwise it seems to result in underclocked timings for dp->pci66mhz == 0.
>
>> + break;
>> + default:
>> + printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
>> + "Using default 8clk.\n", clk);
>> + clocks = 0; /* 8 clk */
>> + break;
>> + }
>> + return clocks << ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
>> +}
>> +
>> +static int atp867x_get_recover_clocks_shifted(unsigned int clk)
>> +{
>> + unsigned char clocks = clk;
>> +
>> + switch (clocks) {
>> + case 0:
>> + clocks = 1;
>> + break;
>> + case 1 ... 11:
>> + break;
>> + case 12:
>> + clocks = 0;
>> + break;
>> + case 13: case 14:
>> + --clocks;
>> + break;
>
> Is "clocks == 14" a reserved setting?
12 is reserved for the default (== 0), and 13, 14 are set to value 12,
13 respectively.
>
> If so a comment documenting it would be appreciated.
Sure. see the new patch below.
>
>> + case 15:
>> + break;
>> + default:
>> + printk(KERN_WARNING "ATP867X: recover %dclk is invalid. "
>> + "Using default 15clk.\n", clk);
>> + clocks = 0; /* 12 clk */
>
> Shouldn't it use "clocks == 15" setting?
It was a typo. 12 is the right default.
>
>> + break;
>> + }
>> + return clocks << ATP867X_IO_PIOSPD_RECOVER_SHIFT;
>> +}
>> +
>> +static void atp867x_set_piomode(struct ata_port *ap, struct ata_device *adev)
>> +{
>> + struct ata_device *peer = ata_dev_pair(adev);
>> + struct atp867x_priv *dp = ap->private_data;
>> + u8 speed = adev->pio_mode;
>> + struct ata_timing t, p;
>> + int T, UT;
>> + u8 b;
>> +
>> + T = 1000000000 / 33333;
>> + UT = T / 4;
>> +
>> + ata_timing_compute(adev, speed, &t, T, UT);
>> + if (peer && peer->pio_mode) {
>> + ata_timing_compute(peer, peer->pio_mode, &p, T, UT);
>> + ata_timing_merge(&p, &t, &t, ATA_TIMING_8BIT);
>> + }
>> +
>> + b = ioread8(dp->dma_mode);
>> + if (adev->devno & 1)
>> + b = (b & ~ATP867X_IO_DMAMODE_SLAVE_MASK);
>> + else
>> + b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK);
>> + iowrite8(b, dp->dma_mode);
>> +
>> + b = atp867x_get_active_clocks_shifted(t.active) |
>> + atp867x_get_recover_clocks_shifted(t.recover);
>> + if (dp->pci66mhz)
>> + b += 0x10;
>
> What is the purpose of the above hack?
For safe PIO mode according to spec.
>
> AFAICS (I don't have a datasheet) it may result in invalid active
> clocks being used for t.active > 12 and 0x80 bit being set incorrectly
> for t.active values 7..12 (unless it was the purpose of the hack).
See the patch below..
>
>> + if (adev->devno & 1)
>> + iowrite8(b, dp->slave_piospd);
>> + else
>> + iowrite8(b, dp->mstr_piospd);
>> +
>> + /*
>> + * use the same value for comand timing as for PIO timimg
>> + */
>> + iowrite8(b, dp->eightb_piospd);
>
> This is incorrect if slave/master devices use different PIO modes
> or if PIO mode <= 2 is used by any device.
>
> Timing based on t.act8b and t.rec8b values should be used instead.
act8b and rec8b have the same values as active, recovery of the port.
If a:r=3:1 then they become 4:1 on 66mhz for safer transfer, and
a8:r8=3:1, which is identical but the a8 should be incremented by 1.
I can use a8:r8 with 66mhz fixup but it becomes the same as using a:r.
Take a look at the patch below.
>
> On the somehow related note:
>
> * I don't see how PIO0-2 command timings can be met with only 3 bits
> used for active clocks. Could it be that dp->eight_piospd should be
> programmed in a slightly different way than dp->{mstr,slave}_piospd?
>
See new patch on clocks_shift below.
> * The controller allows higher clocks values for recovery timings but
> ata_timing_compute() tries to fairly increase both recovery and active
> timings to meet the required cycle timing.
>
>> +}
>> +
>> +static int atp867x_cable_detect(struct ata_port *ap)
>> +{
>> + return ATA_CBL_PATA40_SHORT;
>> +}
>
> As noticed by Robert and Alan already:
>
> This should use ATA_CBL_PATA_UNK and rely on the driver-side cable detection.
I modified cable_detect() to use override; on a certain
subsystem_vendor|device, its 40short, others, unknown.
>
>
> One last thing: Power Management support is missing from this driver
> (I tried addressing this in the separately posted patch but it needs
> testing by somebody with the hardware).
>
>
> MWDMA fix:
>
> From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Subject: [PATCH] pata_atp867x: fix it to not claim MWDMA support
>
> MWDMA modes are not supported by this driver currently.
>
> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> ---
> drivers/ata/pata_atp867x.c | 10 +---------
> 1 file changed, 1 insertion(+), 9 deletions(-)
>
> Index: b/drivers/ata/pata_atp867x.c
> ===================================================================
> --- a/drivers/ata/pata_atp867x.c
> +++ b/drivers/ata/pata_atp867x.c
> @@ -118,20 +118,13 @@ struct atp867x_priv {
> int pci66mhz;
> };
>
> -static inline u8 atp867x_speed_to_mode(u8 speed)
> -{
> - return speed - XFER_UDMA_0 + 1;
> -}
> -
> static void atp867x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
> {
> struct pci_dev *pdev = to_pci_dev(ap->host->dev);
> struct atp867x_priv *dp = ap->private_data;
> u8 speed = adev->dma_mode;
> u8 b;
> - u8 mode;
> -
> - mode = atp867x_speed_to_mode(speed);
> + u8 mode = speed - XFER_UDMA_0 + 1;
>
> /*
> * Doc 6.6.9: decrease the udma mode value by 1 for safer UDMA speed
> @@ -471,7 +464,6 @@ static int atp867x_init_one(struct pci_d
> static const struct ata_port_info info_867x = {
> .flags = ATA_FLAG_SLAVE_POSS,
> .pio_mask = ATA_PIO4,
> - .mwdma_mask = ATA_MWDMA2,
This looks good to me. thx.
> .udma_mask = ATA_UDMA6,
> .port_ops = &atp867x_ops,
> };
>
From: John(Jung-Ik) Lee <jilee@google.com>
clarifications in timings calculations and cable detection
Signed-off-by: John(Jung-Ik) Lee <jilee@google.com>
---
pata_atp867x.c | 50 +++++++++++++++++++++++++++++++++++++-------------
1 files changed, 37 insertions, 13 deletions
diff --git a/drivers/ata/pata_atp867x.c b/drivers/ata/pata_atp867x.c
index e6c4706..c1c691f 100644
--- a/drivers/ata/pata_atp867x.c
+++ b/drivers/ata/pata_atp867x.c
@@ -156,8 +156,10 @@ static void atp867x_set_dmamode(struct ata_port
*ap, struct ata_device *adev)
iowrite8(b, dp->dma_mode);
}
-static int atp867x_get_active_clocks_shifted(unsigned int clk)
+static int atp867x_get_active_clocks_shifted(struct ata_port *ap,
+ unsigned int clk)
{
+ struct atp867x_priv *dp = ap->private_data;
unsigned char clocks = clk;
switch (clocks) {
@@ -166,15 +168,25 @@ static int
atp867x_get_active_clocks_shifted(unsigned int clk)
break;
case 1 ... 7:
break;
- case 8 ... 12:
+ case 9 ... 12:
clocks = 7;
break;
default:
printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
"Using default 8clk.\n", clk);
- clocks = 0; /* 8 clk */
- break;
+ case 8: /* default 8 clk */
+ clocks = 0;
+ goto active_clock_shift_done;
}
+
+ /*
+ * Doc 6.6.9: increase the clock value by 1 for safer PIO speed
+ * on 66MHz bus
+ */
+ if (dp->pci66mhz && clocks < 7)
+ clocks++;
+
+active_clock_shift_done:
return clocks << ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
}
@@ -188,20 +200,19 @@ static int
atp867x_get_recover_clocks_shifted(unsigned int clk)
break;
case 1 ... 11:
break;
- case 12:
- clocks = 0;
- break;
case 13: case 14:
- --clocks;
+ --clocks; /* by the spec */
break;
case 15:
break;
default:
printk(KERN_WARNING "ATP867X: recover %dclk is invalid. "
"Using default 12clk.\n", clk);
- clocks = 0; /* 12 clk */
+ case 12: /* default 12 clk */
+ clocks = 0;
break;
}
+
return clocks << ATP867X_IO_PIOSPD_RECOVER_SHIFT;
}
@@ -230,10 +241,8 @@ static void atp867x_set_piomode(struct ata_port
*ap, struct ata_device *adev)
b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK);
iowrite8(b, dp->dma_mode);
- b = atp867x_get_active_clocks_shifted(t.active) |
+ b = atp867x_get_active_clocks_shifted(ap, t.active) |
atp867x_get_recover_clocks_shifted(t.recover);
- if (dp->pci66mhz)
- b += 0x10;
if (adev->devno & 1)
iowrite8(b, dp->slave_piospd);
@@ -246,9 +255,24 @@ static void atp867x_set_piomode(struct ata_port
*ap, struct ata_device *adev)
iowrite8(b, dp->eightb_piospd);
}
+static int atp867x_cable_override(struct pci_dev *pdev)
+{
+ if (pdev->subsystem_vendor == PCI_VENDOR_ID_ARTOP &&
+ (pdev->subsystem_device == PCI_DEVICE_ID_ARTOP_ATP867A ||
+ pdev->subsystem_device == PCI_DEVICE_ID_ARTOP_ATP867B)) {
+ return 1;
+ }
+ return 0;
+}
+
static int atp867x_cable_detect(struct ata_port *ap)
{
- return ATA_CBL_PATA40_SHORT;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+ if (atp867x_cable_override(pdev))
+ return ATA_CBL_PATA40_SHORT;
+
+ return ATA_CBL_PATA_UNK;
}
static struct scsi_host_template atp867x_sht = {
^ permalink raw reply related [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2009-09-17 20:49 Jeff Garzik
@ 2009-09-20 21:05 ` Bartlomiej Zolnierkiewicz
2009-09-22 2:36 ` Jung-Ik (John) Lee
0 siblings, 1 reply; 95+ messages in thread
From: Bartlomiej Zolnierkiewicz @ 2009-09-20 21:05 UTC (permalink / raw)
To: Jeff Garzik
Cc: Andrew Morton, Linus Torvalds, linux-ide, LKML, John Lee,
Grant Grundler, Gwendal Gringo
On Thursday 17 September 2009 22:49:35 Jeff Garzik wrote:
>
> Bug fixes, and a new driver.
>
>
>
> Please pull from 'upstream-linus' branch of
> master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
>
> to receive the following updates:
>
> drivers/ata/Kconfig | 9 +
> drivers/ata/Makefile | 1 +
> drivers/ata/ahci.c | 4 +-
> drivers/ata/libata-core.c | 4 +-
> drivers/ata/pata_amd.c | 3 +
> drivers/ata/pata_atp867x.c | 548 ++++++++++++++++++++++++++++++++++++++++++++
> drivers/ata/sata_promise.c | 155 +++++++++++--
> include/linux/pci_ids.h | 2 +
> 8 files changed, 704 insertions(+), 22 deletions(-)
> create mode 100644 drivers/ata/pata_atp867x.c
>
> John(Jung-Ik) Lee (1):
> libata: Add pata_atp867x driver for Artop/Acard ATP867X controllers
That was really fast.. Not necessarily a bad thing but this driver would
benefit from few polishing touches..
> diff --git a/drivers/ata/pata_atp867x.c b/drivers/ata/pata_atp867x.c
> new file mode 100644
> index 0000000..7990de9
> --- /dev/null
> +++ b/drivers/ata/pata_atp867x.c
> @@ -0,0 +1,548 @@
> +/*
> + * pata_atp867x.c - ARTOP 867X 64bit 4-channel UDMA133 ATA controller driver
> + *
> + * (C) 2009 Google Inc. John(Jung-Ik) Lee <jilee@google.com>
> + *
> + * Per Atp867 data sheet rev 1.2, Acard.
> + * Based in part on early ide code from
> + * 2003-2004 by Eric Uhrhane, Google, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
> + *
> + *
> + * TODO:
> + * 1. RAID features [comparison, XOR, striping, mirroring, etc.]
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/pci.h>
> +#include <linux/init.h>
> +#include <linux/blkdev.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <scsi/scsi_host.h>
> +#include <linux/libata.h>
> +
> +#define DRV_NAME "pata_atp867x"
> +#define DRV_VERSION "0.7.5"
> +
> +/*
> + * IO Registers
> + * Note that all runtime hot priv ports are cached in ap private_data
> + */
> +
> +enum {
> + ATP867X_IO_CHANNEL_OFFSET = 0x10,
> +
> + /*
> + * IO Register Bitfields
> + */
> +
> + ATP867X_IO_PIOSPD_ACTIVE_SHIFT = 4,
> + ATP867X_IO_PIOSPD_RECOVER_SHIFT = 0,
> +
> + ATP867X_IO_DMAMODE_MSTR_SHIFT = 0,
> + ATP867X_IO_DMAMODE_MSTR_MASK = 0x07,
> + ATP867X_IO_DMAMODE_SLAVE_SHIFT = 4,
> + ATP867X_IO_DMAMODE_SLAVE_MASK = 0x70,
> +
> + ATP867X_IO_DMAMODE_UDMA_6 = 0x07,
> + ATP867X_IO_DMAMODE_UDMA_5 = 0x06,
> + ATP867X_IO_DMAMODE_UDMA_4 = 0x05,
> + ATP867X_IO_DMAMODE_UDMA_3 = 0x04,
> + ATP867X_IO_DMAMODE_UDMA_2 = 0x03,
> + ATP867X_IO_DMAMODE_UDMA_1 = 0x02,
> + ATP867X_IO_DMAMODE_UDMA_0 = 0x01,
> + ATP867X_IO_DMAMODE_DISABLE = 0x00,
> +
> + ATP867X_IO_SYS_INFO_66MHZ = 0x04,
> + ATP867X_IO_SYS_INFO_SLOW_UDMA5 = 0x02,
> + ATP867X_IO_SYS_MASK_RESERVED = (~0xf1),
> +
> + ATP867X_IO_PORTSPD_VAL = 0x1143,
> + ATP867X_PREREAD_VAL = 0x0200,
> +
> + ATP867X_NUM_PORTS = 4,
> + ATP867X_BAR_IOBASE = 0,
> + ATP867X_BAR_ROMBASE = 6,
> +};
> +
> +#define ATP867X_IOBASE(ap) ((ap)->host->iomap[0])
> +#define ATP867X_SYS_INFO(ap) (0x3F + ATP867X_IOBASE(ap))
> +
> +#define ATP867X_IO_PORTBASE(ap, port) (0x00 + ATP867X_IOBASE(ap) + \
> + (port) * ATP867X_IO_CHANNEL_OFFSET)
> +#define ATP867X_IO_DMABASE(ap, port) (0x40 + \
> + ATP867X_IO_PORTBASE((ap), (port)))
> +
> +#define ATP867X_IO_STATUS(ap, port) (0x07 + \
> + ATP867X_IO_PORTBASE((ap), (port)))
> +#define ATP867X_IO_ALTSTATUS(ap, port) (0x0E + \
> + ATP867X_IO_PORTBASE((ap), (port)))
> +
> +/*
> + * hot priv ports
> + */
> +#define ATP867X_IO_MSTRPIOSPD(ap, port) (0x08 + \
> + ATP867X_IO_DMABASE((ap), (port)))
> +#define ATP867X_IO_SLAVPIOSPD(ap, port) (0x09 + \
> + ATP867X_IO_DMABASE((ap), (port)))
> +#define ATP867X_IO_8BPIOSPD(ap, port) (0x0A + \
> + ATP867X_IO_DMABASE((ap), (port)))
> +#define ATP867X_IO_DMAMODE(ap, port) (0x0B + \
> + ATP867X_IO_DMABASE((ap), (port)))
> +
> +#define ATP867X_IO_PORTSPD(ap, port) (0x4A + \
> + ATP867X_IO_PORTBASE((ap), (port)))
> +#define ATP867X_IO_PREREAD(ap, port) (0x4C + \
> + ATP867X_IO_PORTBASE((ap), (port)))
> +
> +struct atp867x_priv {
> + void __iomem *dma_mode;
> + void __iomem *mstr_piospd;
> + void __iomem *slave_piospd;
> + void __iomem *eightb_piospd;
> + int pci66mhz;
> +};
> +
> +static inline u8 atp867x_speed_to_mode(u8 speed)
> +{
> + return speed - XFER_UDMA_0 + 1;
> +}
> +
> +static void atp867x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
> +{
> + struct pci_dev *pdev = to_pci_dev(ap->host->dev);
> + struct atp867x_priv *dp = ap->private_data;
> + u8 speed = adev->dma_mode;
> + u8 b;
> + u8 mode;
> +
> + mode = atp867x_speed_to_mode(speed);
The driver currently doesn't support MWDMA modes but claims otherwise
(fixed in the attached patch).
> + /*
> + * Doc 6.6.9: decrease the udma mode value by 1 for safer UDMA speed
> + * on 66MHz bus
> + * rev-A: UDMA_1~4 (5, 6 no change)
> + * rev-B: all UDMA modes
> + * UDMA_0 stays not to disable UDMA
> + */
> + if (dp->pci66mhz && mode > ATP867X_IO_DMAMODE_UDMA_0 &&
> + (pdev->device == PCI_DEVICE_ID_ARTOP_ATP867B ||
> + mode < ATP867X_IO_DMAMODE_UDMA_5))
> + mode--;
> +
> + b = ioread8(dp->dma_mode);
> + if (adev->devno & 1) {
> + b = (b & ~ATP867X_IO_DMAMODE_SLAVE_MASK) |
> + (mode << ATP867X_IO_DMAMODE_SLAVE_SHIFT);
> + } else {
> + b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK) |
> + (mode << ATP867X_IO_DMAMODE_MSTR_SHIFT);
> + }
> + iowrite8(b, dp->dma_mode);
> +}
> +
> +static int atp867x_get_active_clocks_shifted(unsigned int clk)
> +{
> + unsigned char clocks = clk;
> +
> + switch (clocks) {
> + case 0:
> + clocks = 1;
> + break;
> + case 1 ... 7:
> + break;
> + case 8 ... 12:
> + clocks = 7;
Shouldn't "clocks = 0" (the default case) be used here?
Otherwise it seems to result in underclocked timings for dp->pci66mhz == 0.
> + break;
> + default:
> + printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
> + "Using default 8clk.\n", clk);
> + clocks = 0; /* 8 clk */
> + break;
> + }
> + return clocks << ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
> +}
> +
> +static int atp867x_get_recover_clocks_shifted(unsigned int clk)
> +{
> + unsigned char clocks = clk;
> +
> + switch (clocks) {
> + case 0:
> + clocks = 1;
> + break;
> + case 1 ... 11:
> + break;
> + case 12:
> + clocks = 0;
> + break;
> + case 13: case 14:
> + --clocks;
> + break;
Is "clocks == 14" a reserved setting?
If so a comment documenting it would be appreciated.
> + case 15:
> + break;
> + default:
> + printk(KERN_WARNING "ATP867X: recover %dclk is invalid. "
> + "Using default 15clk.\n", clk);
> + clocks = 0; /* 12 clk */
Shouldn't it use "clocks == 15" setting?
> + break;
> + }
> + return clocks << ATP867X_IO_PIOSPD_RECOVER_SHIFT;
> +}
> +
> +static void atp867x_set_piomode(struct ata_port *ap, struct ata_device *adev)
> +{
> + struct ata_device *peer = ata_dev_pair(adev);
> + struct atp867x_priv *dp = ap->private_data;
> + u8 speed = adev->pio_mode;
> + struct ata_timing t, p;
> + int T, UT;
> + u8 b;
> +
> + T = 1000000000 / 33333;
> + UT = T / 4;
> +
> + ata_timing_compute(adev, speed, &t, T, UT);
> + if (peer && peer->pio_mode) {
> + ata_timing_compute(peer, peer->pio_mode, &p, T, UT);
> + ata_timing_merge(&p, &t, &t, ATA_TIMING_8BIT);
> + }
> +
> + b = ioread8(dp->dma_mode);
> + if (adev->devno & 1)
> + b = (b & ~ATP867X_IO_DMAMODE_SLAVE_MASK);
> + else
> + b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK);
> + iowrite8(b, dp->dma_mode);
> +
> + b = atp867x_get_active_clocks_shifted(t.active) |
> + atp867x_get_recover_clocks_shifted(t.recover);
> + if (dp->pci66mhz)
> + b += 0x10;
What is the purpose of the above hack?
AFAICS (I don't have a datasheet) it may result in invalid active
clocks being used for t.active > 12 and 0x80 bit being set incorrectly
for t.active values 7..12 (unless it was the purpose of the hack).
> + if (adev->devno & 1)
> + iowrite8(b, dp->slave_piospd);
> + else
> + iowrite8(b, dp->mstr_piospd);
> +
> + /*
> + * use the same value for comand timing as for PIO timimg
> + */
> + iowrite8(b, dp->eightb_piospd);
This is incorrect if slave/master devices use different PIO modes
or if PIO mode <= 2 is used by any device.
Timing based on t.act8b and t.rec8b values should be used instead.
On the somehow related note:
* I don't see how PIO0-2 command timings can be met with only 3 bits
used for active clocks. Could it be that dp->eight_piospd should be
programmed in a slightly different way than dp->{mstr,slave}_piospd?
* The controller allows higher clocks values for recovery timings but
ata_timing_compute() tries to fairly increase both recovery and active
timings to meet the required cycle timing.
> +}
> +
> +static int atp867x_cable_detect(struct ata_port *ap)
> +{
> + return ATA_CBL_PATA40_SHORT;
> +}
As noticed by Robert and Alan already:
This should use ATA_CBL_PATA_UNK and rely on the driver-side cable detection.
One last thing: Power Management support is missing from this driver
(I tried addressing this in the separately posted patch but it needs
testing by somebody with the hardware).
MWDMA fix:
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Subject: [PATCH] pata_atp867x: fix it to not claim MWDMA support
MWDMA modes are not supported by this driver currently.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
drivers/ata/pata_atp867x.c | 10 +---------
1 file changed, 1 insertion(+), 9 deletions(-)
Index: b/drivers/ata/pata_atp867x.c
===================================================================
--- a/drivers/ata/pata_atp867x.c
+++ b/drivers/ata/pata_atp867x.c
@@ -118,20 +118,13 @@ struct atp867x_priv {
int pci66mhz;
};
-static inline u8 atp867x_speed_to_mode(u8 speed)
-{
- return speed - XFER_UDMA_0 + 1;
-}
-
static void atp867x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct atp867x_priv *dp = ap->private_data;
u8 speed = adev->dma_mode;
u8 b;
- u8 mode;
-
- mode = atp867x_speed_to_mode(speed);
+ u8 mode = speed - XFER_UDMA_0 + 1;
/*
* Doc 6.6.9: decrease the udma mode value by 1 for safer UDMA speed
@@ -471,7 +464,6 @@ static int atp867x_init_one(struct pci_d
static const struct ata_port_info info_867x = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &atp867x_ops,
};
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2009-09-17 20:49 Jeff Garzik
2009-09-20 21:05 ` Bartlomiej Zolnierkiewicz
0 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2009-09-17 20:49 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Bug fixes, and a new driver.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/Kconfig | 9 +
drivers/ata/Makefile | 1 +
drivers/ata/ahci.c | 4 +-
drivers/ata/libata-core.c | 4 +-
drivers/ata/pata_amd.c | 3 +
drivers/ata/pata_atp867x.c | 548 ++++++++++++++++++++++++++++++++++++++++++++
drivers/ata/sata_promise.c | 155 +++++++++++--
include/linux/pci_ids.h | 2 +
8 files changed, 704 insertions(+), 22 deletions(-)
create mode 100644 drivers/ata/pata_atp867x.c
John(Jung-Ik) Lee (1):
libata: Add pata_atp867x driver for Artop/Acard ATP867X controllers
Mikael Pettersson (2):
sata_promise: disable hotplug on 1st gen chips
sata_promise: update reset code
Robert Hancock (1):
pata_amd: do not filter out valid modes in nv_mode_filter
Tejun Heo (2):
ahci: restore pci_intx() handling
libata: fix spurious WARN_ON_ONCE() on port freeze
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index ab2fa4e..f2df6e2 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -255,6 +255,15 @@ config PATA_ARTOP
If unsure, say N.
+config PATA_ATP867X
+ tristate "ARTOP/Acard ATP867X PATA support"
+ depends on PCI
+ help
+ This option enables support for ARTOP/Acard ATP867X PATA
+ controllers.
+
+ If unsure, say N.
+
config PATA_AT32
tristate "Atmel AVR32 PATA support (Experimental)"
depends on AVR32 && PLATFORM_AT32AP && EXPERIMENTAL
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 463eb52..01e126f 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -22,6 +22,7 @@ obj-$(CONFIG_SATA_FSL) += sata_fsl.o
obj-$(CONFIG_PATA_ALI) += pata_ali.o
obj-$(CONFIG_PATA_AMD) += pata_amd.o
obj-$(CONFIG_PATA_ARTOP) += pata_artop.o
+obj-$(CONFIG_PATA_ATP867X) += pata_atp867x.o
obj-$(CONFIG_PATA_AT32) += pata_at32.o
obj-$(CONFIG_PATA_ATIIXP) += pata_atiixp.o
obj-$(CONFIG_PATA_CMD640_PCI) += pata_cmd640.o
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index d4cd9c2..acd1162 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -2930,8 +2930,8 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (ahci_sb600_32bit_only(pdev))
hpriv->flags |= AHCI_HFLAG_32BIT_ONLY;
- if (!(hpriv->flags & AHCI_HFLAG_NO_MSI))
- pci_enable_msi(pdev);
+ if ((hpriv->flags & AHCI_HFLAG_NO_MSI) || pci_enable_msi(pdev))
+ pci_intx(pdev, 1);
/* save initial config */
ahci_save_initial_config(pdev, hpriv);
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index df31dea..0ddaf43 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -5024,8 +5024,6 @@ void ata_qc_complete(struct ata_queued_cmd *qc)
struct ata_device *dev = qc->dev;
struct ata_eh_info *ehi = &dev->link->eh_info;
- WARN_ON_ONCE(ap->pflags & ATA_PFLAG_FROZEN);
-
if (unlikely(qc->err_mask))
qc->flags |= ATA_QCFLAG_FAILED;
@@ -5038,6 +5036,8 @@ void ata_qc_complete(struct ata_queued_cmd *qc)
}
}
+ WARN_ON_ONCE(ap->pflags & ATA_PFLAG_FROZEN);
+
/* read result TF if requested */
if (qc->flags & ATA_QCFLAG_RESULT_TF)
fill_result_tf(qc);
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index 33a74f1..567f3f7 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -307,6 +307,9 @@ static unsigned long nv_mode_filter(struct ata_device *dev,
limit |= ATA_MASK_PIO;
if (!(limit & (ATA_MASK_MWDMA | ATA_MASK_UDMA)))
limit |= ATA_MASK_MWDMA | ATA_MASK_UDMA;
+ /* PIO4, MWDMA2, UDMA2 should always be supported regardless of
+ cable detection result */
+ limit |= ata_pack_xfermask(ATA_PIO4, ATA_MWDMA2, ATA_UDMA2);
ata_port_printk(ap, KERN_DEBUG, "nv_mode_filter: 0x%lx&0x%lx->0x%lx, "
"BIOS=0x%lx (0x%x) ACPI=0x%lx%s\n",
diff --git a/drivers/ata/pata_atp867x.c b/drivers/ata/pata_atp867x.c
new file mode 100644
index 0000000..7990de9
--- /dev/null
+++ b/drivers/ata/pata_atp867x.c
@@ -0,0 +1,548 @@
+/*
+ * pata_atp867x.c - ARTOP 867X 64bit 4-channel UDMA133 ATA controller driver
+ *
+ * (C) 2009 Google Inc. John(Jung-Ik) Lee <jilee@google.com>
+ *
+ * Per Atp867 data sheet rev 1.2, Acard.
+ * Based in part on early ide code from
+ * 2003-2004 by Eric Uhrhane, Google, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ *
+ * TODO:
+ * 1. RAID features [comparison, XOR, striping, mirroring, etc.]
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_atp867x"
+#define DRV_VERSION "0.7.5"
+
+/*
+ * IO Registers
+ * Note that all runtime hot priv ports are cached in ap private_data
+ */
+
+enum {
+ ATP867X_IO_CHANNEL_OFFSET = 0x10,
+
+ /*
+ * IO Register Bitfields
+ */
+
+ ATP867X_IO_PIOSPD_ACTIVE_SHIFT = 4,
+ ATP867X_IO_PIOSPD_RECOVER_SHIFT = 0,
+
+ ATP867X_IO_DMAMODE_MSTR_SHIFT = 0,
+ ATP867X_IO_DMAMODE_MSTR_MASK = 0x07,
+ ATP867X_IO_DMAMODE_SLAVE_SHIFT = 4,
+ ATP867X_IO_DMAMODE_SLAVE_MASK = 0x70,
+
+ ATP867X_IO_DMAMODE_UDMA_6 = 0x07,
+ ATP867X_IO_DMAMODE_UDMA_5 = 0x06,
+ ATP867X_IO_DMAMODE_UDMA_4 = 0x05,
+ ATP867X_IO_DMAMODE_UDMA_3 = 0x04,
+ ATP867X_IO_DMAMODE_UDMA_2 = 0x03,
+ ATP867X_IO_DMAMODE_UDMA_1 = 0x02,
+ ATP867X_IO_DMAMODE_UDMA_0 = 0x01,
+ ATP867X_IO_DMAMODE_DISABLE = 0x00,
+
+ ATP867X_IO_SYS_INFO_66MHZ = 0x04,
+ ATP867X_IO_SYS_INFO_SLOW_UDMA5 = 0x02,
+ ATP867X_IO_SYS_MASK_RESERVED = (~0xf1),
+
+ ATP867X_IO_PORTSPD_VAL = 0x1143,
+ ATP867X_PREREAD_VAL = 0x0200,
+
+ ATP867X_NUM_PORTS = 4,
+ ATP867X_BAR_IOBASE = 0,
+ ATP867X_BAR_ROMBASE = 6,
+};
+
+#define ATP867X_IOBASE(ap) ((ap)->host->iomap[0])
+#define ATP867X_SYS_INFO(ap) (0x3F + ATP867X_IOBASE(ap))
+
+#define ATP867X_IO_PORTBASE(ap, port) (0x00 + ATP867X_IOBASE(ap) + \
+ (port) * ATP867X_IO_CHANNEL_OFFSET)
+#define ATP867X_IO_DMABASE(ap, port) (0x40 + \
+ ATP867X_IO_PORTBASE((ap), (port)))
+
+#define ATP867X_IO_STATUS(ap, port) (0x07 + \
+ ATP867X_IO_PORTBASE((ap), (port)))
+#define ATP867X_IO_ALTSTATUS(ap, port) (0x0E + \
+ ATP867X_IO_PORTBASE((ap), (port)))
+
+/*
+ * hot priv ports
+ */
+#define ATP867X_IO_MSTRPIOSPD(ap, port) (0x08 + \
+ ATP867X_IO_DMABASE((ap), (port)))
+#define ATP867X_IO_SLAVPIOSPD(ap, port) (0x09 + \
+ ATP867X_IO_DMABASE((ap), (port)))
+#define ATP867X_IO_8BPIOSPD(ap, port) (0x0A + \
+ ATP867X_IO_DMABASE((ap), (port)))
+#define ATP867X_IO_DMAMODE(ap, port) (0x0B + \
+ ATP867X_IO_DMABASE((ap), (port)))
+
+#define ATP867X_IO_PORTSPD(ap, port) (0x4A + \
+ ATP867X_IO_PORTBASE((ap), (port)))
+#define ATP867X_IO_PREREAD(ap, port) (0x4C + \
+ ATP867X_IO_PORTBASE((ap), (port)))
+
+struct atp867x_priv {
+ void __iomem *dma_mode;
+ void __iomem *mstr_piospd;
+ void __iomem *slave_piospd;
+ void __iomem *eightb_piospd;
+ int pci66mhz;
+};
+
+static inline u8 atp867x_speed_to_mode(u8 speed)
+{
+ return speed - XFER_UDMA_0 + 1;
+}
+
+static void atp867x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ struct atp867x_priv *dp = ap->private_data;
+ u8 speed = adev->dma_mode;
+ u8 b;
+ u8 mode;
+
+ mode = atp867x_speed_to_mode(speed);
+
+ /*
+ * Doc 6.6.9: decrease the udma mode value by 1 for safer UDMA speed
+ * on 66MHz bus
+ * rev-A: UDMA_1~4 (5, 6 no change)
+ * rev-B: all UDMA modes
+ * UDMA_0 stays not to disable UDMA
+ */
+ if (dp->pci66mhz && mode > ATP867X_IO_DMAMODE_UDMA_0 &&
+ (pdev->device == PCI_DEVICE_ID_ARTOP_ATP867B ||
+ mode < ATP867X_IO_DMAMODE_UDMA_5))
+ mode--;
+
+ b = ioread8(dp->dma_mode);
+ if (adev->devno & 1) {
+ b = (b & ~ATP867X_IO_DMAMODE_SLAVE_MASK) |
+ (mode << ATP867X_IO_DMAMODE_SLAVE_SHIFT);
+ } else {
+ b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK) |
+ (mode << ATP867X_IO_DMAMODE_MSTR_SHIFT);
+ }
+ iowrite8(b, dp->dma_mode);
+}
+
+static int atp867x_get_active_clocks_shifted(unsigned int clk)
+{
+ unsigned char clocks = clk;
+
+ switch (clocks) {
+ case 0:
+ clocks = 1;
+ break;
+ case 1 ... 7:
+ break;
+ case 8 ... 12:
+ clocks = 7;
+ break;
+ default:
+ printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
+ "Using default 8clk.\n", clk);
+ clocks = 0; /* 8 clk */
+ break;
+ }
+ return clocks << ATP867X_IO_PIOSPD_ACTIVE_SHIFT;
+}
+
+static int atp867x_get_recover_clocks_shifted(unsigned int clk)
+{
+ unsigned char clocks = clk;
+
+ switch (clocks) {
+ case 0:
+ clocks = 1;
+ break;
+ case 1 ... 11:
+ break;
+ case 12:
+ clocks = 0;
+ break;
+ case 13: case 14:
+ --clocks;
+ break;
+ case 15:
+ break;
+ default:
+ printk(KERN_WARNING "ATP867X: recover %dclk is invalid. "
+ "Using default 15clk.\n", clk);
+ clocks = 0; /* 12 clk */
+ break;
+ }
+ return clocks << ATP867X_IO_PIOSPD_RECOVER_SHIFT;
+}
+
+static void atp867x_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct ata_device *peer = ata_dev_pair(adev);
+ struct atp867x_priv *dp = ap->private_data;
+ u8 speed = adev->pio_mode;
+ struct ata_timing t, p;
+ int T, UT;
+ u8 b;
+
+ T = 1000000000 / 33333;
+ UT = T / 4;
+
+ ata_timing_compute(adev, speed, &t, T, UT);
+ if (peer && peer->pio_mode) {
+ ata_timing_compute(peer, peer->pio_mode, &p, T, UT);
+ ata_timing_merge(&p, &t, &t, ATA_TIMING_8BIT);
+ }
+
+ b = ioread8(dp->dma_mode);
+ if (adev->devno & 1)
+ b = (b & ~ATP867X_IO_DMAMODE_SLAVE_MASK);
+ else
+ b = (b & ~ATP867X_IO_DMAMODE_MSTR_MASK);
+ iowrite8(b, dp->dma_mode);
+
+ b = atp867x_get_active_clocks_shifted(t.active) |
+ atp867x_get_recover_clocks_shifted(t.recover);
+ if (dp->pci66mhz)
+ b += 0x10;
+
+ if (adev->devno & 1)
+ iowrite8(b, dp->slave_piospd);
+ else
+ iowrite8(b, dp->mstr_piospd);
+
+ /*
+ * use the same value for comand timing as for PIO timimg
+ */
+ iowrite8(b, dp->eightb_piospd);
+}
+
+static int atp867x_cable_detect(struct ata_port *ap)
+{
+ return ATA_CBL_PATA40_SHORT;
+}
+
+static struct scsi_host_template atp867x_sht = {
+ ATA_BMDMA_SHT(DRV_NAME),
+};
+
+static struct ata_port_operations atp867x_ops = {
+ .inherits = &ata_bmdma_port_ops,
+ .cable_detect = atp867x_cable_detect,
+ .set_piomode = atp867x_set_piomode,
+ .set_dmamode = atp867x_set_dmamode,
+};
+
+
+#ifdef ATP867X_DEBUG
+static void atp867x_check_res(struct pci_dev *pdev)
+{
+ int i;
+ unsigned long start, len;
+
+ /* Check the PCI resources for this channel are enabled */
+ for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) {
+ start = pci_resource_start(pdev, i);
+ len = pci_resource_len(pdev, i);
+ printk(KERN_DEBUG "ATP867X: resource start:len=%lx:%lx\n",
+ start, len);
+ }
+}
+
+static void atp867x_check_ports(struct ata_port *ap, int port)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ struct atp867x_priv *dp = ap->private_data;
+
+ printk(KERN_DEBUG "ATP867X: port[%d] addresses\n"
+ " cmd_addr =0x%llx, 0x%llx\n"
+ " ctl_addr =0x%llx, 0x%llx\n"
+ " bmdma_addr =0x%llx, 0x%llx\n"
+ " data_addr =0x%llx\n"
+ " error_addr =0x%llx\n"
+ " feature_addr =0x%llx\n"
+ " nsect_addr =0x%llx\n"
+ " lbal_addr =0x%llx\n"
+ " lbam_addr =0x%llx\n"
+ " lbah_addr =0x%llx\n"
+ " device_addr =0x%llx\n"
+ " status_addr =0x%llx\n"
+ " command_addr =0x%llx\n"
+ " dp->dma_mode =0x%llx\n"
+ " dp->mstr_piospd =0x%llx\n"
+ " dp->slave_piospd =0x%llx\n"
+ " dp->eightb_piospd =0x%llx\n"
+ " dp->pci66mhz =0x%lx\n",
+ port,
+ (unsigned long long)ioaddr->cmd_addr,
+ (unsigned long long)ATP867X_IO_PORTBASE(ap, port),
+ (unsigned long long)ioaddr->ctl_addr,
+ (unsigned long long)ATP867X_IO_ALTSTATUS(ap, port),
+ (unsigned long long)ioaddr->bmdma_addr,
+ (unsigned long long)ATP867X_IO_DMABASE(ap, port),
+ (unsigned long long)ioaddr->data_addr,
+ (unsigned long long)ioaddr->error_addr,
+ (unsigned long long)ioaddr->feature_addr,
+ (unsigned long long)ioaddr->nsect_addr,
+ (unsigned long long)ioaddr->lbal_addr,
+ (unsigned long long)ioaddr->lbam_addr,
+ (unsigned long long)ioaddr->lbah_addr,
+ (unsigned long long)ioaddr->device_addr,
+ (unsigned long long)ioaddr->status_addr,
+ (unsigned long long)ioaddr->command_addr,
+ (unsigned long long)dp->dma_mode,
+ (unsigned long long)dp->mstr_piospd,
+ (unsigned long long)dp->slave_piospd,
+ (unsigned long long)dp->eightb_piospd,
+ (unsigned long)dp->pci66mhz);
+}
+#endif
+
+static int atp867x_set_priv(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ struct atp867x_priv *dp;
+ int port = ap->port_no;
+
+ dp = ap->private_data =
+ devm_kzalloc(&pdev->dev, sizeof(*dp), GFP_KERNEL);
+ if (dp == NULL)
+ return -ENOMEM;
+
+ dp->dma_mode = ATP867X_IO_DMAMODE(ap, port);
+ dp->mstr_piospd = ATP867X_IO_MSTRPIOSPD(ap, port);
+ dp->slave_piospd = ATP867X_IO_SLAVPIOSPD(ap, port);
+ dp->eightb_piospd = ATP867X_IO_8BPIOSPD(ap, port);
+
+ dp->pci66mhz =
+ ioread8(ATP867X_SYS_INFO(ap)) & ATP867X_IO_SYS_INFO_66MHZ;
+
+ return 0;
+}
+
+static void atp867x_fixup(struct ata_host *host)
+{
+ struct pci_dev *pdev = to_pci_dev(host->dev);
+ struct ata_port *ap = host->ports[0];
+ int i;
+ u8 v;
+
+ /*
+ * Broken BIOS might not set latency high enough
+ */
+ pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &v);
+ if (v < 0x80) {
+ v = 0x80;
+ pci_write_config_byte(pdev, PCI_LATENCY_TIMER, v);
+ printk(KERN_DEBUG "ATP867X: set latency timer of device %s"
+ " to %d\n", pci_name(pdev), v);
+ }
+
+ /*
+ * init 8bit io ports speed(0aaarrrr) to 43h and
+ * init udma modes of master/slave to 0/0(11h)
+ */
+ for (i = 0; i < ATP867X_NUM_PORTS; i++)
+ iowrite16(ATP867X_IO_PORTSPD_VAL, ATP867X_IO_PORTSPD(ap, i));
+
+ /*
+ * init PreREAD counts
+ */
+ for (i = 0; i < ATP867X_NUM_PORTS; i++)
+ iowrite16(ATP867X_PREREAD_VAL, ATP867X_IO_PREREAD(ap, i));
+
+ v = ioread8(ATP867X_IOBASE(ap) + 0x28);
+ v &= 0xcf; /* Enable INTA#: bit4=0 means enable */
+ v |= 0xc0; /* Enable PCI burst, MRM & not immediate interrupts */
+ iowrite8(v, ATP867X_IOBASE(ap) + 0x28);
+
+ /*
+ * Turn off the over clocked udma5 mode, only for Rev-B
+ */
+ v = ioread8(ATP867X_SYS_INFO(ap));
+ v &= ATP867X_IO_SYS_MASK_RESERVED;
+ if (pdev->device == PCI_DEVICE_ID_ARTOP_ATP867B)
+ v |= ATP867X_IO_SYS_INFO_SLOW_UDMA5;
+ iowrite8(v, ATP867X_SYS_INFO(ap));
+}
+
+static int atp867x_ata_pci_sff_init_host(struct ata_host *host)
+{
+ struct device *gdev = host->dev;
+ struct pci_dev *pdev = to_pci_dev(gdev);
+ unsigned int mask = 0;
+ int i, rc;
+
+ /*
+ * do not map rombase
+ */
+ rc = pcim_iomap_regions(pdev, 1 << ATP867X_BAR_IOBASE, DRV_NAME);
+ if (rc == -EBUSY)
+ pcim_pin_device(pdev);
+ if (rc)
+ return rc;
+ host->iomap = pcim_iomap_table(pdev);
+
+#ifdef ATP867X_DEBUG
+ atp867x_check_res(pdev);
+
+ for (i = 0; i < PCI_ROM_RESOURCE; i++)
+ printk(KERN_DEBUG "ATP867X: iomap[%d]=0x%llx\n", i,
+ (unsigned long long)(host->iomap[i]));
+#endif
+
+ /*
+ * request, iomap BARs and init port addresses accordingly
+ */
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap = host->ports[i];
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+
+ ioaddr->cmd_addr = ATP867X_IO_PORTBASE(ap, i);
+ ioaddr->ctl_addr = ioaddr->altstatus_addr
+ = ATP867X_IO_ALTSTATUS(ap, i);
+ ioaddr->bmdma_addr = ATP867X_IO_DMABASE(ap, i);
+
+ ata_sff_std_ports(ioaddr);
+ rc = atp867x_set_priv(ap);
+ if (rc)
+ return rc;
+
+#ifdef ATP867X_DEBUG
+ atp867x_check_ports(ap, i);
+#endif
+ ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx",
+ (unsigned long)ioaddr->cmd_addr,
+ (unsigned long)ioaddr->ctl_addr);
+ ata_port_desc(ap, "bmdma 0x%lx",
+ (unsigned long)ioaddr->bmdma_addr);
+
+ mask |= 1 << i;
+ }
+
+ if (!mask) {
+ dev_printk(KERN_ERR, gdev, "no available native port\n");
+ return -ENODEV;
+ }
+
+ atp867x_fixup(host);
+
+ rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+ if (rc)
+ return rc;
+
+ rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+ return rc;
+}
+
+static int atp867x_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *id)
+{
+ static int printed_version;
+ static const struct ata_port_info info_867x = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &atp867x_ops,
+ };
+
+ struct ata_host *host;
+ const struct ata_port_info *ppi[] = { &info_867x, NULL };
+ int rc;
+
+ if (!printed_version++)
+ dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
+
+ rc = pcim_enable_device(pdev);
+ if (rc)
+ return rc;
+
+ printk(KERN_INFO "ATP867X: ATP867 ATA UDMA133 controller (rev %02X)",
+ pdev->device);
+
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, ATP867X_NUM_PORTS);
+ if (!host) {
+ dev_printk(KERN_ERR, &pdev->dev,
+ "failed to allocate ATA host\n");
+ rc = -ENOMEM;
+ goto err_out;
+ }
+
+ rc = atp867x_ata_pci_sff_init_host(host);
+ if (rc) {
+ dev_printk(KERN_ERR, &pdev->dev, "failed to init host\n");
+ goto err_out;
+ }
+
+ pci_set_master(pdev);
+
+ rc = ata_host_activate(host, pdev->irq, ata_sff_interrupt,
+ IRQF_SHARED, &atp867x_sht);
+ if (rc)
+ dev_printk(KERN_ERR, &pdev->dev, "failed to activate host\n");
+
+err_out:
+ return rc;
+}
+
+static struct pci_device_id atp867x_pci_tbl[] = {
+ { PCI_VDEVICE(ARTOP, PCI_DEVICE_ID_ARTOP_ATP867A), 0 },
+ { PCI_VDEVICE(ARTOP, PCI_DEVICE_ID_ARTOP_ATP867B), 0 },
+ { },
+};
+
+static struct pci_driver atp867x_driver = {
+ .name = DRV_NAME,
+ .id_table = atp867x_pci_tbl,
+ .probe = atp867x_init_one,
+ .remove = ata_pci_remove_one,
+};
+
+static int __init atp867x_init(void)
+{
+ return pci_register_driver(&atp867x_driver);
+}
+
+static void __exit atp867x_exit(void)
+{
+ pci_unregister_driver(&atp867x_driver);
+}
+
+MODULE_AUTHOR("John(Jung-Ik) Lee, Google Inc.");
+MODULE_DESCRIPTION("low level driver for Artop/Acard 867x ATA controller");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, atp867x_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(atp867x_init);
+module_exit(atp867x_exit);
diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c
index b1fd7d6..07d8d00 100644
--- a/drivers/ata/sata_promise.c
+++ b/drivers/ata/sata_promise.c
@@ -56,6 +56,7 @@ enum {
/* host register offsets (from host->iomap[PDC_MMIO_BAR]) */
PDC_INT_SEQMASK = 0x40, /* Mask of asserted SEQ INTs */
PDC_FLASH_CTL = 0x44, /* Flash control register */
+ PDC_PCI_CTL = 0x48, /* PCI control/status reg */
PDC_SATA_PLUG_CSR = 0x6C, /* SATA Plug control/status reg */
PDC2_SATA_PLUG_CSR = 0x60, /* SATAII Plug control/status reg */
PDC_TBG_MODE = 0x41C, /* TBG mode (not SATAII) */
@@ -75,7 +76,17 @@ enum {
PDC_CTLSTAT = 0x60, /* IDE control and status (per port) */
/* per-port SATA register offsets (from ap->ioaddr.scr_addr) */
+ PDC_SATA_ERROR = 0x04,
PDC_PHYMODE4 = 0x14,
+ PDC_LINK_LAYER_ERRORS = 0x6C,
+ PDC_FPDMA_CTLSTAT = 0xD8,
+ PDC_INTERNAL_DEBUG_1 = 0xF8, /* also used for PATA */
+ PDC_INTERNAL_DEBUG_2 = 0xFC, /* also used for PATA */
+
+ /* PDC_FPDMA_CTLSTAT bit definitions */
+ PDC_FPDMA_CTLSTAT_RESET = 1 << 3,
+ PDC_FPDMA_CTLSTAT_DMASETUP_INT_FLAG = 1 << 10,
+ PDC_FPDMA_CTLSTAT_SETDB_INT_FLAG = 1 << 11,
/* PDC_GLOBAL_CTL bit definitions */
PDC_PH_ERR = (1 << 8), /* PCI error while loading packet */
@@ -195,9 +206,12 @@ static struct ata_port_operations pdc_sata_ops = {
.hardreset = pdc_sata_hardreset,
};
-/* First-generation chips need a more restrictive ->check_atapi_dma op */
+/* First-generation chips need a more restrictive ->check_atapi_dma op,
+ and ->freeze/thaw that ignore the hotplug controls. */
static struct ata_port_operations pdc_old_sata_ops = {
.inherits = &pdc_sata_ops,
+ .freeze = pdc_freeze,
+ .thaw = pdc_thaw,
.check_atapi_dma = pdc_old_sata_check_atapi_dma,
};
@@ -356,12 +370,76 @@ static int pdc_sata_port_start(struct ata_port *ap)
return 0;
}
+static void pdc_fpdma_clear_interrupt_flag(struct ata_port *ap)
+{
+ void __iomem *sata_mmio = ap->ioaddr.scr_addr;
+ u32 tmp;
+
+ tmp = readl(sata_mmio + PDC_FPDMA_CTLSTAT);
+ tmp |= PDC_FPDMA_CTLSTAT_DMASETUP_INT_FLAG;
+ tmp |= PDC_FPDMA_CTLSTAT_SETDB_INT_FLAG;
+
+ /* It's not allowed to write to the entire FPDMA_CTLSTAT register
+ when NCQ is running. So do a byte-sized write to bits 10 and 11. */
+ writeb(tmp >> 8, sata_mmio + PDC_FPDMA_CTLSTAT + 1);
+ readb(sata_mmio + PDC_FPDMA_CTLSTAT + 1); /* flush */
+}
+
+static void pdc_fpdma_reset(struct ata_port *ap)
+{
+ void __iomem *sata_mmio = ap->ioaddr.scr_addr;
+ u8 tmp;
+
+ tmp = (u8)readl(sata_mmio + PDC_FPDMA_CTLSTAT);
+ tmp &= 0x7F;
+ tmp |= PDC_FPDMA_CTLSTAT_RESET;
+ writeb(tmp, sata_mmio + PDC_FPDMA_CTLSTAT);
+ readl(sata_mmio + PDC_FPDMA_CTLSTAT); /* flush */
+ udelay(100);
+ tmp &= ~PDC_FPDMA_CTLSTAT_RESET;
+ writeb(tmp, sata_mmio + PDC_FPDMA_CTLSTAT);
+ readl(sata_mmio + PDC_FPDMA_CTLSTAT); /* flush */
+
+ pdc_fpdma_clear_interrupt_flag(ap);
+}
+
+static void pdc_not_at_command_packet_phase(struct ata_port *ap)
+{
+ void __iomem *sata_mmio = ap->ioaddr.scr_addr;
+ unsigned int i;
+ u32 tmp;
+
+ /* check not at ASIC packet command phase */
+ for (i = 0; i < 100; ++i) {
+ writel(0, sata_mmio + PDC_INTERNAL_DEBUG_1);
+ tmp = readl(sata_mmio + PDC_INTERNAL_DEBUG_2);
+ if ((tmp & 0xF) != 1)
+ break;
+ udelay(100);
+ }
+}
+
+static void pdc_clear_internal_debug_record_error_register(struct ata_port *ap)
+{
+ void __iomem *sata_mmio = ap->ioaddr.scr_addr;
+
+ writel(0xffffffff, sata_mmio + PDC_SATA_ERROR);
+ writel(0xffff0000, sata_mmio + PDC_LINK_LAYER_ERRORS);
+}
+
static void pdc_reset_port(struct ata_port *ap)
{
void __iomem *ata_ctlstat_mmio = ap->ioaddr.cmd_addr + PDC_CTLSTAT;
unsigned int i;
u32 tmp;
+ if (ap->flags & PDC_FLAG_GEN_II)
+ pdc_not_at_command_packet_phase(ap);
+
+ tmp = readl(ata_ctlstat_mmio);
+ tmp |= PDC_RESET;
+ writel(tmp, ata_ctlstat_mmio);
+
for (i = 11; i > 0; i--) {
tmp = readl(ata_ctlstat_mmio);
if (tmp & PDC_RESET)
@@ -376,6 +454,11 @@ static void pdc_reset_port(struct ata_port *ap)
tmp &= ~PDC_RESET;
writel(tmp, ata_ctlstat_mmio);
readl(ata_ctlstat_mmio); /* flush */
+
+ if (sata_scr_valid(&ap->link) && (ap->flags & PDC_FLAG_GEN_II)) {
+ pdc_fpdma_reset(ap);
+ pdc_clear_internal_debug_record_error_register(ap);
+ }
}
static int pdc_pata_cable_detect(struct ata_port *ap)
@@ -626,11 +709,6 @@ static unsigned int pdc_sata_ata_port_to_ata_no(const struct ata_port *ap)
return pdc_port_no_to_ata_no(i, pdc_is_sataii_tx4(ap->flags));
}
-static unsigned int pdc_sata_hotplug_offset(const struct ata_port *ap)
-{
- return (ap->flags & PDC_FLAG_GEN_II) ? PDC2_SATA_PLUG_CSR : PDC_SATA_PLUG_CSR;
-}
-
static void pdc_freeze(struct ata_port *ap)
{
void __iomem *ata_mmio = ap->ioaddr.cmd_addr;
@@ -647,7 +725,7 @@ static void pdc_sata_freeze(struct ata_port *ap)
{
struct ata_host *host = ap->host;
void __iomem *host_mmio = host->iomap[PDC_MMIO_BAR];
- unsigned int hotplug_offset = pdc_sata_hotplug_offset(ap);
+ unsigned int hotplug_offset = PDC2_SATA_PLUG_CSR;
unsigned int ata_no = pdc_sata_ata_port_to_ata_no(ap);
u32 hotplug_status;
@@ -685,7 +763,7 @@ static void pdc_sata_thaw(struct ata_port *ap)
{
struct ata_host *host = ap->host;
void __iomem *host_mmio = host->iomap[PDC_MMIO_BAR];
- unsigned int hotplug_offset = pdc_sata_hotplug_offset(ap);
+ unsigned int hotplug_offset = PDC2_SATA_PLUG_CSR;
unsigned int ata_no = pdc_sata_ata_port_to_ata_no(ap);
u32 hotplug_status;
@@ -708,11 +786,50 @@ static int pdc_pata_softreset(struct ata_link *link, unsigned int *class,
return ata_sff_softreset(link, class, deadline);
}
+static unsigned int pdc_ata_port_to_ata_no(const struct ata_port *ap)
+{
+ void __iomem *ata_mmio = ap->ioaddr.cmd_addr;
+ void __iomem *host_mmio = ap->host->iomap[PDC_MMIO_BAR];
+
+ /* ata_mmio == host_mmio + 0x200 + ata_no * 0x80 */
+ return (ata_mmio - host_mmio - 0x200) / 0x80;
+}
+
+static void pdc_hard_reset_port(struct ata_port *ap)
+{
+ void __iomem *host_mmio = ap->host->iomap[PDC_MMIO_BAR];
+ void __iomem *pcictl_b1_mmio = host_mmio + PDC_PCI_CTL + 1;
+ unsigned int ata_no = pdc_ata_port_to_ata_no(ap);
+ u8 tmp;
+
+ spin_lock(&ap->host->lock);
+
+ tmp = readb(pcictl_b1_mmio);
+ tmp &= ~(0x10 << ata_no);
+ writeb(tmp, pcictl_b1_mmio);
+ readb(pcictl_b1_mmio); /* flush */
+ udelay(100);
+ tmp |= (0x10 << ata_no);
+ writeb(tmp, pcictl_b1_mmio);
+ readb(pcictl_b1_mmio); /* flush */
+
+ spin_unlock(&ap->host->lock);
+}
+
static int pdc_sata_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline)
{
+ if (link->ap->flags & PDC_FLAG_GEN_II)
+ pdc_not_at_command_packet_phase(link->ap);
+ /* hotplug IRQs should have been masked by pdc_sata_freeze() */
+ pdc_hard_reset_port(link->ap);
pdc_reset_port(link->ap);
- return sata_sff_hardreset(link, class, deadline);
+
+ /* sata_promise can't reliably acquire the first D2H Reg FIS
+ * after hardreset. Do non-waiting hardreset and request
+ * follow-up SRST.
+ */
+ return sata_std_hardreset(link, class, deadline);
}
static void pdc_error_handler(struct ata_port *ap)
@@ -832,14 +949,14 @@ static irqreturn_t pdc_interrupt(int irq, void *dev_instance)
spin_lock(&host->lock);
/* read and clear hotplug flags for all ports */
- if (host->ports[0]->flags & PDC_FLAG_GEN_II)
+ if (host->ports[0]->flags & PDC_FLAG_GEN_II) {
hotplug_offset = PDC2_SATA_PLUG_CSR;
- else
- hotplug_offset = PDC_SATA_PLUG_CSR;
- hotplug_status = readl(host_mmio + hotplug_offset);
- if (hotplug_status & 0xff)
- writel(hotplug_status | 0xff, host_mmio + hotplug_offset);
- hotplug_status &= 0xff; /* clear uninteresting bits */
+ hotplug_status = readl(host_mmio + hotplug_offset);
+ if (hotplug_status & 0xff)
+ writel(hotplug_status | 0xff, host_mmio + hotplug_offset);
+ hotplug_status &= 0xff; /* clear uninteresting bits */
+ } else
+ hotplug_status = 0;
/* reading should also clear interrupts */
mask = readl(host_mmio + PDC_INT_SEQMASK);
@@ -1034,9 +1151,11 @@ static void pdc_host_init(struct ata_host *host)
tmp = readl(host_mmio + hotplug_offset);
writel(tmp | 0xff, host_mmio + hotplug_offset);
- /* unmask plug/unplug ints */
tmp = readl(host_mmio + hotplug_offset);
- writel(tmp & ~0xff0000, host_mmio + hotplug_offset);
+ if (is_gen2) /* unmask plug/unplug ints */
+ writel(tmp & ~0xff0000, host_mmio + hotplug_offset);
+ else /* mask plug/unplug ints */
+ writel(tmp | 0xff0000, host_mmio + hotplug_offset);
/* don't initialise TBG or SLEW on 2nd generation chips */
if (is_gen2)
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 8975add..3b6b788 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -1529,6 +1529,8 @@
#define PCI_DEVICE_ID_ARTOP_ATP860R 0x0007
#define PCI_DEVICE_ID_ARTOP_ATP865 0x0008
#define PCI_DEVICE_ID_ARTOP_ATP865R 0x0009
+#define PCI_DEVICE_ID_ARTOP_ATP867A 0x000A
+#define PCI_DEVICE_ID_ARTOP_ATP867B 0x000B
#define PCI_DEVICE_ID_ARTOP_AEC7610 0x8002
#define PCI_DEVICE_ID_ARTOP_AEC7612UW 0x8010
#define PCI_DEVICE_ID_ARTOP_AEC7612U 0x8020
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2009-06-23 6:06 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2009-06-23 6:06 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/Kconfig | 8 +
drivers/ata/Makefile | 1 +
drivers/ata/libata-core.c | 25 ++--
drivers/ata/pata_at91.c | 361 +++++++++++++++++++++++++++++++++++++++++++++
drivers/ata/sata_fsl.c | 35 +++++
5 files changed, 420 insertions(+), 10 deletions(-)
create mode 100644 drivers/ata/pata_at91.c
Dave Liu (1):
sata_fsl: Add power mgmt support
Evgeni Golov (1):
[libata] beautify module parameters
Sergey Matyukevich (1):
[libata] PATA driver for CF interface on AT91SAM9260 SoC
Tejun Heo (1):
libata: don't set IORDY for reset
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 2aa1908..b17c57f 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -679,6 +679,14 @@ config PATA_PLATFORM
If unsure, say N.
+config PATA_AT91
+ tristate "PATA support for AT91SAM9260"
+ depends on ARM && ARCH_AT91
+ help
+ This option enables support for IDE devices on the Atmel AT91SAM9260 SoC.
+
+ If unsure, say N.
+
config PATA_OF_PLATFORM
tristate "OpenFirmware platform device PATA support"
depends on PATA_PLATFORM && PPC_OF
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 1558059..38906f9 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -72,6 +72,7 @@ obj-$(CONFIG_PATA_SCH) += pata_sch.o
obj-$(CONFIG_PATA_BF54X) += pata_bf54x.o
obj-$(CONFIG_PATA_OCTEON_CF) += pata_octeon_cf.o
obj-$(CONFIG_PATA_PLATFORM) += pata_platform.o
+obj-$(CONFIG_PATA_AT91) += pata_at91.o
obj-$(CONFIG_PATA_OF_PLATFORM) += pata_of_platform.o
obj-$(CONFIG_PATA_ICSIDE) += pata_icside.o
# Should be last but two libata driver
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index ca4d208..045a486 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -125,19 +125,19 @@ MODULE_PARM_DESC(force, "Force ATA configurations including cable type, link spe
static int atapi_enabled = 1;
module_param(atapi_enabled, int, 0444);
-MODULE_PARM_DESC(atapi_enabled, "Enable discovery of ATAPI devices (0=off, 1=on)");
+MODULE_PARM_DESC(atapi_enabled, "Enable discovery of ATAPI devices (0=off, 1=on [default])");
static int atapi_dmadir = 0;
module_param(atapi_dmadir, int, 0444);
-MODULE_PARM_DESC(atapi_dmadir, "Enable ATAPI DMADIR bridge support (0=off, 1=on)");
+MODULE_PARM_DESC(atapi_dmadir, "Enable ATAPI DMADIR bridge support (0=off [default], 1=on)");
int atapi_passthru16 = 1;
module_param(atapi_passthru16, int, 0444);
-MODULE_PARM_DESC(atapi_passthru16, "Enable ATA_16 passthru for ATAPI devices; on by default (0=off, 1=on)");
+MODULE_PARM_DESC(atapi_passthru16, "Enable ATA_16 passthru for ATAPI devices (0=off, 1=on [default])");
int libata_fua = 0;
module_param_named(fua, libata_fua, int, 0444);
-MODULE_PARM_DESC(fua, "FUA support (0=off, 1=on)");
+MODULE_PARM_DESC(fua, "FUA support (0=off [default], 1=on)");
static int ata_ignore_hpa;
module_param_named(ignore_hpa, ata_ignore_hpa, int, 0644);
@@ -153,11 +153,11 @@ MODULE_PARM_DESC(ata_probe_timeout, "Set ATA probing timeout (seconds)");
int libata_noacpi = 0;
module_param_named(noacpi, libata_noacpi, int, 0444);
-MODULE_PARM_DESC(noacpi, "Disables the use of ACPI in probe/suspend/resume when set");
+MODULE_PARM_DESC(noacpi, "Disable the use of ACPI in probe/suspend/resume (0=off [default], 1=on)");
int libata_allow_tpm = 0;
module_param_named(allow_tpm, libata_allow_tpm, int, 0444);
-MODULE_PARM_DESC(allow_tpm, "Permit the use of TPM commands");
+MODULE_PARM_DESC(allow_tpm, "Permit the use of TPM commands (0=off [default], 1=on)");
MODULE_AUTHOR("Jeff Garzik");
MODULE_DESCRIPTION("Library module for ATA devices");
@@ -1993,11 +1993,17 @@ unsigned int ata_do_simple_cmd(struct ata_device *dev, u8 cmd)
* Check if the current speed of the device requires IORDY. Used
* by various controllers for chip configuration.
*/
-
unsigned int ata_pio_need_iordy(const struct ata_device *adev)
{
- /* Controller doesn't support IORDY. Probably a pointless check
- as the caller should know this */
+ /* Don't set IORDY if we're preparing for reset. IORDY may
+ * lead to controller lock up on certain controllers if the
+ * port is not occupied. See bko#11703 for details.
+ */
+ if (adev->link->ap->pflags & ATA_PFLAG_RESETTING)
+ return 0;
+ /* Controller doesn't support IORDY. Probably a pointless
+ * check as the caller should know this.
+ */
if (adev->link->ap->flags & ATA_FLAG_NO_IORDY)
return 0;
/* CF spec. r4.1 Table 22 says no iordy on PIO5 and PIO6. */
@@ -2020,7 +2026,6 @@ unsigned int ata_pio_need_iordy(const struct ata_device *adev)
* Compute the highest mode possible if we are not using iordy. Return
* -1 if no iordy mode is available.
*/
-
static u32 ata_pio_mask_no_iordy(const struct ata_device *adev)
{
/* If we have no drive specific rule, then PIO 2 is non IORDY */
diff --git a/drivers/ata/pata_at91.c b/drivers/ata/pata_at91.c
new file mode 100644
index 0000000..4b27617
--- /dev/null
+++ b/drivers/ata/pata_at91.c
@@ -0,0 +1,361 @@
+/*
+ * PATA driver for AT91SAM9260 Static Memory Controller
+ * with CompactFlash interface in True IDE mode
+ *
+ * Copyright (C) 2009 Matyukevich Sergey
+ *
+ * Based on:
+ * * generic platform driver by Paul Mundt: drivers/ata/pata_platform.c
+ * * pata_at32 driver by Kristoffer Nyborg Gregertsen
+ * * at91_ide driver by Stanislaw Gruszka
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <scsi/scsi_host.h>
+#include <linux/ata.h>
+#include <linux/clk.h>
+#include <linux/libata.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+
+#include <mach/at91sam9260_matrix.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/at91sam9260.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+
+
+#define DRV_NAME "pata_at91"
+#define DRV_VERSION "0.1"
+
+#define CF_IDE_OFFSET 0x00c00000
+#define CF_ALT_IDE_OFFSET 0x00e00000
+#define CF_IDE_RES_SIZE 0x08
+
+struct at91_ide_info {
+ unsigned long mode;
+ unsigned int cs;
+
+ void __iomem *ide_addr;
+ void __iomem *alt_addr;
+};
+
+const struct ata_timing initial_timing =
+ {XFER_PIO_0, 70, 290, 240, 600, 165, 150, 600, 0};
+
+static unsigned int calc_mck_cycles(unsigned int ns, unsigned int mck_hz)
+{
+ unsigned long mul;
+
+ /*
+ * cycles = x [nsec] * f [Hz] / 10^9 [ns in sec] =
+ * x * (f / 1_000_000_000) =
+ * x * ((f * 65536) / 1_000_000_000) / 65536 =
+ * x * (((f / 10_000) * 65536) / 100_000) / 65536 =
+ */
+
+ mul = (mck_hz / 10000) << 16;
+ mul /= 100000;
+
+ return (ns * mul + 65536) >> 16; /* rounding */
+}
+
+static void set_smc_mode(struct at91_ide_info *info)
+{
+ at91_sys_write(AT91_SMC_MODE(info->cs), info->mode);
+ return;
+}
+
+static void set_smc_timing(struct device *dev,
+ struct at91_ide_info *info, const struct ata_timing *ata)
+{
+ int read_cycle, write_cycle, active, recover;
+ int nrd_setup, nrd_pulse, nrd_recover;
+ int nwe_setup, nwe_pulse;
+
+ int ncs_write_setup, ncs_write_pulse;
+ int ncs_read_setup, ncs_read_pulse;
+
+ unsigned int mck_hz;
+ struct clk *mck;
+
+ read_cycle = ata->cyc8b;
+ nrd_setup = ata->setup;
+ nrd_pulse = ata->act8b;
+ nrd_recover = ata->rec8b;
+
+ mck = clk_get(NULL, "mck");
+ BUG_ON(IS_ERR(mck));
+ mck_hz = clk_get_rate(mck);
+
+ read_cycle = calc_mck_cycles(read_cycle, mck_hz);
+ nrd_setup = calc_mck_cycles(nrd_setup, mck_hz);
+ nrd_pulse = calc_mck_cycles(nrd_pulse, mck_hz);
+ nrd_recover = calc_mck_cycles(nrd_recover, mck_hz);
+
+ clk_put(mck);
+
+ active = nrd_setup + nrd_pulse;
+ recover = read_cycle - active;
+
+ /* Need at least two cycles recovery */
+ if (recover < 2)
+ read_cycle = active + 2;
+
+ /* (CS0, CS1, DIR, OE) <= (CFCE1, CFCE2, CFRNW, NCSX) timings */
+ ncs_read_setup = 1;
+ ncs_read_pulse = read_cycle - 2;
+
+ /* Write timings same as read timings */
+ write_cycle = read_cycle;
+ nwe_setup = nrd_setup;
+ nwe_pulse = nrd_pulse;
+ ncs_write_setup = ncs_read_setup;
+ ncs_write_pulse = ncs_read_pulse;
+
+ dev_dbg(dev, "ATA timings: nrd_setup = %d nrd_pulse = %d nrd_cycle = %d\n",
+ nrd_setup, nrd_pulse, read_cycle);
+ dev_dbg(dev, "ATA timings: nwe_setup = %d nwe_pulse = %d nwe_cycle = %d\n",
+ nwe_setup, nwe_pulse, write_cycle);
+ dev_dbg(dev, "ATA timings: ncs_read_setup = %d ncs_read_pulse = %d\n",
+ ncs_read_setup, ncs_read_pulse);
+ dev_dbg(dev, "ATA timings: ncs_write_setup = %d ncs_write_pulse = %d\n",
+ ncs_write_setup, ncs_write_pulse);
+
+ at91_sys_write(AT91_SMC_SETUP(info->cs),
+ AT91_SMC_NWESETUP_(nwe_setup) |
+ AT91_SMC_NRDSETUP_(nrd_setup) |
+ AT91_SMC_NCS_WRSETUP_(ncs_write_setup) |
+ AT91_SMC_NCS_RDSETUP_(ncs_read_setup));
+
+ at91_sys_write(AT91_SMC_PULSE(info->cs),
+ AT91_SMC_NWEPULSE_(nwe_pulse) |
+ AT91_SMC_NRDPULSE_(nrd_pulse) |
+ AT91_SMC_NCS_WRPULSE_(ncs_write_pulse) |
+ AT91_SMC_NCS_RDPULSE_(ncs_read_pulse));
+
+ at91_sys_write(AT91_SMC_CYCLE(info->cs),
+ AT91_SMC_NWECYCLE_(write_cycle) |
+ AT91_SMC_NRDCYCLE_(read_cycle));
+
+ return;
+}
+
+static void pata_at91_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct at91_ide_info *info = ap->host->private_data;
+ struct ata_timing timing;
+ int ret;
+
+ /* Compute ATA timing and set it to SMC */
+ ret = ata_timing_compute(adev, adev->pio_mode, &timing, 1000, 0);
+ if (ret) {
+ dev_warn(ap->dev, "Failed to compute ATA timing %d, \
+ set PIO_0 timing\n", ret);
+ set_smc_timing(ap->dev, info, &initial_timing);
+ } else {
+ set_smc_timing(ap->dev, info, &timing);
+ }
+
+ /* Setup SMC mode */
+ set_smc_mode(info);
+
+ return;
+}
+
+static unsigned int pata_at91_data_xfer_noirq(struct ata_device *dev,
+ unsigned char *buf, unsigned int buflen, int rw)
+{
+ struct at91_ide_info *info = dev->link->ap->host->private_data;
+ unsigned int consumed;
+ unsigned long flags;
+ unsigned int mode;
+
+ local_irq_save(flags);
+ mode = at91_sys_read(AT91_SMC_MODE(info->cs));
+
+ /* set 16bit mode before writing data */
+ at91_sys_write(AT91_SMC_MODE(info->cs),
+ (mode & ~AT91_SMC_DBW) | AT91_SMC_DBW_16);
+
+ consumed = ata_sff_data_xfer(dev, buf, buflen, rw);
+
+ /* restore 8bit mode after data is written */
+ at91_sys_write(AT91_SMC_MODE(info->cs),
+ (mode & ~AT91_SMC_DBW) | AT91_SMC_DBW_8);
+
+ local_irq_restore(flags);
+ return consumed;
+}
+
+static struct scsi_host_template pata_at91_sht = {
+ ATA_PIO_SHT(DRV_NAME),
+};
+
+static struct ata_port_operations pata_at91_port_ops = {
+ .inherits = &ata_sff_port_ops,
+
+ .sff_data_xfer = pata_at91_data_xfer_noirq,
+ .set_piomode = pata_at91_set_piomode,
+ .cable_detect = ata_cable_40wire,
+ .port_start = ATA_OP_NULL,
+};
+
+static int __devinit pata_at91_probe(struct platform_device *pdev)
+{
+ struct at91_cf_data *board = pdev->dev.platform_data;
+ struct device *dev = &pdev->dev;
+ struct at91_ide_info *info;
+ struct resource *mem_res;
+ struct ata_host *host;
+ struct ata_port *ap;
+ int irq_flags = 0;
+ int irq = 0;
+ int ret;
+
+ /* get platform resources: IO/CTL memories and irq/rst pins */
+
+ if (pdev->num_resources != 1) {
+ dev_err(&pdev->dev, "invalid number of resources\n");
+ return -EINVAL;
+ }
+
+ mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ if (!mem_res) {
+ dev_err(dev, "failed to get mem resource\n");
+ return -EINVAL;
+ }
+
+ irq = board->irq_pin;
+
+ /* init ata host */
+
+ host = ata_host_alloc(dev, 1);
+
+ if (!host)
+ return -ENOMEM;
+
+ ap = host->ports[0];
+ ap->ops = &pata_at91_port_ops;
+ ap->flags |= ATA_FLAG_SLAVE_POSS;
+ ap->pio_mask = ATA_PIO4;
+
+ if (!irq) {
+ ap->flags |= ATA_FLAG_PIO_POLLING;
+ ata_port_desc(ap, "no IRQ, using PIO polling");
+ }
+
+ info = kzalloc(sizeof(*info), GFP_KERNEL);
+
+ if (!info) {
+ dev_err(dev, "failed to allocate memory for private data\n");
+ return -ENOMEM;
+ }
+
+ info->cs = board->chipselect;
+ info->mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
+ AT91_SMC_EXNWMODE_READY | AT91_SMC_BAT_SELECT |
+ AT91_SMC_DBW_8 | AT91_SMC_TDF_(0);
+
+ info->ide_addr = devm_ioremap(dev,
+ mem_res->start + CF_IDE_OFFSET, CF_IDE_RES_SIZE);
+
+ if (!info->ide_addr) {
+ dev_err(dev, "failed to map IO base\n");
+ ret = -ENOMEM;
+ goto err_ide_ioremap;
+ }
+
+ info->alt_addr = devm_ioremap(dev,
+ mem_res->start + CF_ALT_IDE_OFFSET, CF_IDE_RES_SIZE);
+
+ if (!info->alt_addr) {
+ dev_err(dev, "failed to map CTL base\n");
+ ret = -ENOMEM;
+ goto err_alt_ioremap;
+ }
+
+ ap->ioaddr.cmd_addr = info->ide_addr;
+ ap->ioaddr.ctl_addr = info->alt_addr + 0x06;
+ ap->ioaddr.altstatus_addr = ap->ioaddr.ctl_addr;
+
+ ata_sff_std_ports(&ap->ioaddr);
+
+ ata_port_desc(ap, "mmio cmd 0x%llx ctl 0x%llx",
+ (unsigned long long)mem_res->start + CF_IDE_OFFSET,
+ (unsigned long long)mem_res->start + CF_ALT_IDE_OFFSET);
+
+ host->private_data = info;
+
+ return ata_host_activate(host, irq ? gpio_to_irq(irq) : 0,
+ irq ? ata_sff_interrupt : NULL,
+ irq_flags, &pata_at91_sht);
+
+err_alt_ioremap:
+ devm_iounmap(dev, info->ide_addr);
+
+err_ide_ioremap:
+ kfree(info);
+
+ return ret;
+}
+
+static int __devexit pata_at91_remove(struct platform_device *pdev)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ struct at91_ide_info *info = host->private_data;
+ struct device *dev = &pdev->dev;
+
+ if (!host)
+ return 0;
+
+ ata_host_detach(host);
+
+ if (!info)
+ return 0;
+
+ devm_iounmap(dev, info->ide_addr);
+ devm_iounmap(dev, info->alt_addr);
+
+ kfree(info);
+ return 0;
+}
+
+static struct platform_driver pata_at91_driver = {
+ .probe = pata_at91_probe,
+ .remove = __devexit_p(pata_at91_remove),
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init pata_at91_init(void)
+{
+ return platform_driver_register(&pata_at91_driver);
+}
+
+static void __exit pata_at91_exit(void)
+{
+ platform_driver_unregister(&pata_at91_driver);
+}
+
+
+module_init(pata_at91_init);
+module_exit(pata_at91_exit);
+
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Driver for CF in True IDE mode on AT91SAM9260 SoC");
+MODULE_AUTHOR("Matyukevich Sergey");
+MODULE_VERSION(DRV_VERSION);
+
diff --git a/drivers/ata/sata_fsl.c b/drivers/ata/sata_fsl.c
index 36b8629..94eaa43 100644
--- a/drivers/ata/sata_fsl.c
+++ b/drivers/ata/sata_fsl.c
@@ -1378,6 +1378,37 @@ static int sata_fsl_remove(struct of_device *ofdev)
return 0;
}
+#ifdef CONFIG_PM
+static int sata_fsl_suspend(struct of_device *op, pm_message_t state)
+{
+ struct ata_host *host = dev_get_drvdata(&op->dev);
+ return ata_host_suspend(host, state);
+}
+
+static int sata_fsl_resume(struct of_device *op)
+{
+ struct ata_host *host = dev_get_drvdata(&op->dev);
+ struct sata_fsl_host_priv *host_priv = host->private_data;
+ int ret;
+ void __iomem *hcr_base = host_priv->hcr_base;
+ struct ata_port *ap = host->ports[0];
+ struct sata_fsl_port_priv *pp = ap->private_data;
+
+ ret = sata_fsl_init_controller(host);
+ if (ret) {
+ dev_printk(KERN_ERR, &op->dev,
+ "Error initialize hardware\n");
+ return ret;
+ }
+
+ /* Recovery the CHBA register in host controller cmd register set */
+ iowrite32(pp->cmdslot_paddr & 0xffffffff, hcr_base + CHBA);
+
+ ata_host_resume(host);
+ return 0;
+}
+#endif
+
static struct of_device_id fsl_sata_match[] = {
{
.compatible = "fsl,pq-sata",
@@ -1392,6 +1423,10 @@ static struct of_platform_driver fsl_sata_driver = {
.match_table = fsl_sata_match,
.probe = sata_fsl_probe,
.remove = sata_fsl_remove,
+#ifdef CONFIG_PM
+ .suspend = sata_fsl_suspend,
+ .resume = sata_fsl_resume,
+#endif
};
static int __init sata_fsl_init(void)
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2009-04-07 1:42 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2009-04-07 1:42 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: LKML, linux-ide, axboe
Notables:
- sata_mv fixes
- add definitions for TRIM infrastructure to linux/ata.h
(part of "discard" support, for more SSD/flash-friendly operation)
- block/blk-settings.c: code comment speling fix from Alan
- other misc fixes
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
block/blk-settings.c | 2 +-
drivers/ata/ahci.c | 17 ++-
drivers/ata/ata_piix.c | 7 +
drivers/ata/pata_octeon_cf.c | 6 +-
drivers/ata/sata_mv.c | 487 ++++++++++++++++++++++++------------------
include/linux/ata.h | 41 ++++
6 files changed, 344 insertions(+), 216 deletions(-)
Alan Cox (1):
pata_artop: typo
David Daney (1):
libata: Remove some redundant casts from pata_octeon_cf.c
David Milburn (1):
libata: ahci enclosure management bios workaround
Mark Lord (8):
sata_mv: revert SoC irq breakage
sata_mv: fix irq mask races
sata_mv: replace 0x1f with ATA_PIO4 (v2)
sata_mv: workaround errata PCI#7
sata_mv: workaround errata SATA#26
sata_mv: cosmetic renames
sata_mv: workaround errata SATA#13
sata_mv: shorten register names
Matthew Wilcox (1):
ata: Add TRIM infrastructure
Tejun Heo (1):
ata_piix: VGN-BX297XP wants the controller power up on suspend
diff --git a/block/blk-settings.c b/block/blk-settings.c
index 59fd05d..69c42ad 100644
--- a/block/blk-settings.c
+++ b/block/blk-settings.c
@@ -431,7 +431,7 @@ EXPORT_SYMBOL(blk_queue_segment_boundary);
*
* description:
* set required memory and length alignment for direct dma transactions.
- * this is used when buiding direct io requests for the queue.
+ * this is used when building direct io requests for the queue.
*
**/
void blk_queue_dma_alignment(struct request_queue *q, int mask)
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 788bba2..6ca4bc0 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -78,6 +78,7 @@ static ssize_t ahci_led_store(struct ata_port *ap, const char *buf,
static ssize_t ahci_transmit_led_message(struct ata_port *ap, u32 state,
ssize_t size);
#define MAX_SLOTS 8
+#define MAX_RETRY 15
enum {
AHCI_PCI_BAR = 5,
@@ -1115,6 +1116,8 @@ static void ahci_start_port(struct ata_port *ap)
struct ahci_port_priv *pp = ap->private_data;
struct ata_link *link;
struct ahci_em_priv *emp;
+ ssize_t rc;
+ int i;
/* enable FIS reception */
ahci_start_fis_rx(ap);
@@ -1126,7 +1129,17 @@ static void ahci_start_port(struct ata_port *ap)
if (ap->flags & ATA_FLAG_EM) {
ata_for_each_link(link, ap, EDGE) {
emp = &pp->em_priv[link->pmp];
- ahci_transmit_led_message(ap, emp->led_state, 4);
+
+ /* EM Transmit bit maybe busy during init */
+ for (i = 0; i < MAX_RETRY; i++) {
+ rc = ahci_transmit_led_message(ap,
+ emp->led_state,
+ 4);
+ if (rc == -EBUSY)
+ udelay(100);
+ else
+ break;
+ }
}
}
@@ -1331,7 +1344,7 @@ static ssize_t ahci_transmit_led_message(struct ata_port *ap, u32 state,
em_ctl = readl(mmio + HOST_EM_CTL);
if (em_ctl & EM_CTL_TM) {
spin_unlock_irqrestore(ap->lock, flags);
- return -EINVAL;
+ return -EBUSY;
}
/*
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index e5cbe80..942d14a 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -1053,6 +1053,13 @@ static int piix_broken_suspend(void)
DMI_MATCH(DMI_PRODUCT_NAME, "PORTEGE M500"),
},
},
+ {
+ .ident = "VGN-BX297XP",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "VGN-BX297XP"),
+ },
+ },
{ } /* terminate list */
};
diff --git a/drivers/ata/pata_octeon_cf.c b/drivers/ata/pata_octeon_cf.c
index efe2c19..8d9343a 100644
--- a/drivers/ata/pata_octeon_cf.c
+++ b/drivers/ata/pata_octeon_cf.c
@@ -503,7 +503,7 @@ static void octeon_cf_dma_setup(struct ata_queued_cmd *qc)
struct ata_port *ap = qc->ap;
struct octeon_cf_port *cf_port;
- cf_port = (struct octeon_cf_port *)ap->private_data;
+ cf_port = ap->private_data;
DPRINTK("ENTER\n");
/* issue r/w command */
qc->cursg = qc->sg;
@@ -596,7 +596,7 @@ static unsigned int octeon_cf_dma_finished(struct ata_port *ap,
if (ap->hsm_task_state != HSM_ST_LAST)
return 0;
- cf_port = (struct octeon_cf_port *)ap->private_data;
+ cf_port = ap->private_data;
dma_cfg.u64 = cvmx_read_csr(CVMX_MIO_BOOT_DMA_CFGX(ocd->dma_engine));
if (dma_cfg.s.size != 0xfffff) {
@@ -657,7 +657,7 @@ static irqreturn_t octeon_cf_interrupt(int irq, void *dev_instance)
continue;
ocd = ap->dev->platform_data;
- cf_port = (struct octeon_cf_port *)ap->private_data;
+ cf_port = ap->private_data;
dma_int.u64 =
cvmx_read_csr(CVMX_MIO_BOOT_DMA_INTX(ocd->dma_engine));
dma_cfg.u64 =
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index a377226..fffba9b 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -28,10 +28,6 @@
/*
* sata_mv TODO list:
*
- * --> More errata workarounds for PCI-X.
- *
- * --> Complete a full errata audit for all chipsets to identify others.
- *
* --> Develop a low-power-consumption strategy, and implement it.
*
* --> Add sysfs attributes for per-chip / per-HC IRQ coalescing thresholds.
@@ -44,6 +40,15 @@
* connect two SATA ports.
*/
+/*
+ * 80x1-B2 errata PCI#11:
+ *
+ * Users of the 6041/6081 Rev.B2 chips (current is C0)
+ * should be careful to insert those cards only onto PCI-X bus #0,
+ * and only in device slots 0..7, not higher. The chips may not
+ * work correctly otherwise (note: this is a pretty rare condition).
+ */
+
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
@@ -64,7 +69,7 @@
#include <linux/libata.h>
#define DRV_NAME "sata_mv"
-#define DRV_VERSION "1.27"
+#define DRV_VERSION "1.28"
/*
* module options
@@ -109,23 +114,23 @@ enum {
* Coalescing defers the interrupt until either the IO_THRESHOLD
* (count of completed I/Os) is met, or the TIME_THRESHOLD is met.
*/
- MV_COAL_REG_BASE = 0x18000,
- MV_IRQ_COAL_CAUSE = (MV_COAL_REG_BASE + 0x08),
+ COAL_REG_BASE = 0x18000,
+ IRQ_COAL_CAUSE = (COAL_REG_BASE + 0x08),
ALL_PORTS_COAL_IRQ = (1 << 4), /* all ports irq event */
- MV_IRQ_COAL_IO_THRESHOLD = (MV_COAL_REG_BASE + 0xcc),
- MV_IRQ_COAL_TIME_THRESHOLD = (MV_COAL_REG_BASE + 0xd0),
+ IRQ_COAL_IO_THRESHOLD = (COAL_REG_BASE + 0xcc),
+ IRQ_COAL_TIME_THRESHOLD = (COAL_REG_BASE + 0xd0),
/*
* Registers for the (unused here) transaction coalescing feature:
*/
- MV_TRAN_COAL_CAUSE_LO = (MV_COAL_REG_BASE + 0x88),
- MV_TRAN_COAL_CAUSE_HI = (MV_COAL_REG_BASE + 0x8c),
+ TRAN_COAL_CAUSE_LO = (COAL_REG_BASE + 0x88),
+ TRAN_COAL_CAUSE_HI = (COAL_REG_BASE + 0x8c),
- MV_SATAHC0_REG_BASE = 0x20000,
- MV_FLASH_CTL_OFS = 0x1046c,
- MV_GPIO_PORT_CTL_OFS = 0x104f0,
- MV_RESET_CFG_OFS = 0x180d8,
+ SATAHC0_REG_BASE = 0x20000,
+ FLASH_CTL = 0x1046c,
+ GPIO_PORT_CTL = 0x104f0,
+ RESET_CFG = 0x180d8,
MV_PCI_REG_SZ = MV_MAJOR_REG_AREA_SZ,
MV_SATAHC_REG_SZ = MV_MAJOR_REG_AREA_SZ,
@@ -180,40 +185,41 @@ enum {
/* PCI interface registers */
- PCI_COMMAND_OFS = 0xc00,
- PCI_COMMAND_MRDTRIG = (1 << 7), /* PCI Master Read Trigger */
+ MV_PCI_COMMAND = 0xc00,
+ MV_PCI_COMMAND_MWRCOM = (1 << 4), /* PCI Master Write Combining */
+ MV_PCI_COMMAND_MRDTRIG = (1 << 7), /* PCI Master Read Trigger */
- PCI_MAIN_CMD_STS_OFS = 0xd30,
+ PCI_MAIN_CMD_STS = 0xd30,
STOP_PCI_MASTER = (1 << 2),
PCI_MASTER_EMPTY = (1 << 3),
GLOB_SFT_RST = (1 << 4),
- MV_PCI_MODE_OFS = 0xd00,
+ MV_PCI_MODE = 0xd00,
MV_PCI_MODE_MASK = 0x30,
MV_PCI_EXP_ROM_BAR_CTL = 0xd2c,
MV_PCI_DISC_TIMER = 0xd04,
MV_PCI_MSI_TRIGGER = 0xc38,
MV_PCI_SERR_MASK = 0xc28,
- MV_PCI_XBAR_TMOUT_OFS = 0x1d04,
+ MV_PCI_XBAR_TMOUT = 0x1d04,
MV_PCI_ERR_LOW_ADDRESS = 0x1d40,
MV_PCI_ERR_HIGH_ADDRESS = 0x1d44,
MV_PCI_ERR_ATTRIBUTE = 0x1d48,
MV_PCI_ERR_COMMAND = 0x1d50,
- PCI_IRQ_CAUSE_OFS = 0x1d58,
- PCI_IRQ_MASK_OFS = 0x1d5c,
+ PCI_IRQ_CAUSE = 0x1d58,
+ PCI_IRQ_MASK = 0x1d5c,
PCI_UNMASK_ALL_IRQS = 0x7fffff, /* bits 22-0 */
- PCIE_IRQ_CAUSE_OFS = 0x1900,
- PCIE_IRQ_MASK_OFS = 0x1910,
+ PCIE_IRQ_CAUSE = 0x1900,
+ PCIE_IRQ_MASK = 0x1910,
PCIE_UNMASK_ALL_IRQS = 0x40a, /* assorted bits */
/* Host Controller Main Interrupt Cause/Mask registers (1 per-chip) */
- PCI_HC_MAIN_IRQ_CAUSE_OFS = 0x1d60,
- PCI_HC_MAIN_IRQ_MASK_OFS = 0x1d64,
- SOC_HC_MAIN_IRQ_CAUSE_OFS = 0x20020,
- SOC_HC_MAIN_IRQ_MASK_OFS = 0x20024,
+ PCI_HC_MAIN_IRQ_CAUSE = 0x1d60,
+ PCI_HC_MAIN_IRQ_MASK = 0x1d64,
+ SOC_HC_MAIN_IRQ_CAUSE = 0x20020,
+ SOC_HC_MAIN_IRQ_MASK = 0x20024,
ERR_IRQ = (1 << 0), /* shift by (2 * port #) */
DONE_IRQ = (1 << 1), /* shift by (2 * port #) */
HC0_IRQ_PEND = 0x1ff, /* bits 0-8 = HC0's ports */
@@ -234,9 +240,9 @@ enum {
HC_MAIN_RSVD_SOC = (0x3fffffb << 6), /* bits 31-9, 7-6 */
/* SATAHC registers */
- HC_CFG_OFS = 0,
+ HC_CFG = 0x00,
- HC_IRQ_CAUSE_OFS = 0x14,
+ HC_IRQ_CAUSE = 0x14,
DMA_IRQ = (1 << 0), /* shift by port # */
HC_COAL_IRQ = (1 << 4), /* IRQ coalescing */
DEV_IRQ = (1 << 8), /* shift by port # */
@@ -248,53 +254,54 @@ enum {
* Coalescing defers the interrupt until either the IO_THRESHOLD
* (count of completed I/Os) is met, or the TIME_THRESHOLD is met.
*/
- HC_IRQ_COAL_IO_THRESHOLD_OFS = 0x000c,
- HC_IRQ_COAL_TIME_THRESHOLD_OFS = 0x0010,
+ HC_IRQ_COAL_IO_THRESHOLD = 0x000c,
+ HC_IRQ_COAL_TIME_THRESHOLD = 0x0010,
- SOC_LED_CTRL_OFS = 0x2c,
+ SOC_LED_CTRL = 0x2c,
SOC_LED_CTRL_BLINK = (1 << 0), /* Active LED blink */
SOC_LED_CTRL_ACT_PRESENCE = (1 << 2), /* Multiplex dev presence */
/* with dev activity LED */
/* Shadow block registers */
- SHD_BLK_OFS = 0x100,
- SHD_CTL_AST_OFS = 0x20, /* ofs from SHD_BLK_OFS */
+ SHD_BLK = 0x100,
+ SHD_CTL_AST = 0x20, /* ofs from SHD_BLK */
/* SATA registers */
- SATA_STATUS_OFS = 0x300, /* ctrl, err regs follow status */
- SATA_ACTIVE_OFS = 0x350,
- SATA_FIS_IRQ_CAUSE_OFS = 0x364,
- SATA_FIS_IRQ_AN = (1 << 9), /* async notification */
+ SATA_STATUS = 0x300, /* ctrl, err regs follow status */
+ SATA_ACTIVE = 0x350,
+ FIS_IRQ_CAUSE = 0x364,
+ FIS_IRQ_CAUSE_AN = (1 << 9), /* async notification */
- LTMODE_OFS = 0x30c,
+ LTMODE = 0x30c, /* requires read-after-write */
LTMODE_BIT8 = (1 << 8), /* unknown, but necessary */
+ PHY_MODE2 = 0x330,
PHY_MODE3 = 0x310,
- PHY_MODE4 = 0x314,
+
+ PHY_MODE4 = 0x314, /* requires read-after-write */
PHY_MODE4_CFG_MASK = 0x00000003, /* phy internal config field */
PHY_MODE4_CFG_VALUE = 0x00000001, /* phy internal config field */
PHY_MODE4_RSVD_ZEROS = 0x5de3fffa, /* Gen2e always write zeros */
PHY_MODE4_RSVD_ONES = 0x00000005, /* Gen2e always write ones */
- PHY_MODE2 = 0x330,
- SATA_IFCTL_OFS = 0x344,
- SATA_TESTCTL_OFS = 0x348,
- SATA_IFSTAT_OFS = 0x34c,
- VENDOR_UNIQUE_FIS_OFS = 0x35c,
+ SATA_IFCTL = 0x344,
+ SATA_TESTCTL = 0x348,
+ SATA_IFSTAT = 0x34c,
+ VENDOR_UNIQUE_FIS = 0x35c,
- FISCFG_OFS = 0x360,
+ FISCFG = 0x360,
FISCFG_WAIT_DEV_ERR = (1 << 8), /* wait for host on DevErr */
FISCFG_SINGLE_SYNC = (1 << 16), /* SYNC on DMA activation */
MV5_PHY_MODE = 0x74,
- MV5_LTMODE_OFS = 0x30,
- MV5_PHY_CTL_OFS = 0x0C,
- SATA_INTERFACE_CFG_OFS = 0x050,
+ MV5_LTMODE = 0x30,
+ MV5_PHY_CTL = 0x0C,
+ SATA_IFCFG = 0x050,
MV_M2_PREAMP_MASK = 0x7e0,
/* Port registers */
- EDMA_CFG_OFS = 0,
+ EDMA_CFG = 0,
EDMA_CFG_Q_DEPTH = 0x1f, /* max device queue depth */
EDMA_CFG_NCQ = (1 << 5), /* for R/W FPDMA queued */
EDMA_CFG_NCQ_GO_ON_ERR = (1 << 14), /* continue on error */
@@ -303,8 +310,8 @@ enum {
EDMA_CFG_EDMA_FBS = (1 << 16), /* EDMA FIS-Based Switching */
EDMA_CFG_FBS = (1 << 26), /* FIS-Based Switching */
- EDMA_ERR_IRQ_CAUSE_OFS = 0x8,
- EDMA_ERR_IRQ_MASK_OFS = 0xc,
+ EDMA_ERR_IRQ_CAUSE = 0x8,
+ EDMA_ERR_IRQ_MASK = 0xc,
EDMA_ERR_D_PAR = (1 << 0), /* UDMA data parity err */
EDMA_ERR_PRD_PAR = (1 << 1), /* UDMA PRD parity err */
EDMA_ERR_DEV = (1 << 2), /* device error */
@@ -373,36 +380,36 @@ enum {
EDMA_ERR_INTRL_PAR |
EDMA_ERR_IORDY,
- EDMA_REQ_Q_BASE_HI_OFS = 0x10,
- EDMA_REQ_Q_IN_PTR_OFS = 0x14, /* also contains BASE_LO */
+ EDMA_REQ_Q_BASE_HI = 0x10,
+ EDMA_REQ_Q_IN_PTR = 0x14, /* also contains BASE_LO */
- EDMA_REQ_Q_OUT_PTR_OFS = 0x18,
+ EDMA_REQ_Q_OUT_PTR = 0x18,
EDMA_REQ_Q_PTR_SHIFT = 5,
- EDMA_RSP_Q_BASE_HI_OFS = 0x1c,
- EDMA_RSP_Q_IN_PTR_OFS = 0x20,
- EDMA_RSP_Q_OUT_PTR_OFS = 0x24, /* also contains BASE_LO */
+ EDMA_RSP_Q_BASE_HI = 0x1c,
+ EDMA_RSP_Q_IN_PTR = 0x20,
+ EDMA_RSP_Q_OUT_PTR = 0x24, /* also contains BASE_LO */
EDMA_RSP_Q_PTR_SHIFT = 3,
- EDMA_CMD_OFS = 0x28, /* EDMA command register */
+ EDMA_CMD = 0x28, /* EDMA command register */
EDMA_EN = (1 << 0), /* enable EDMA */
EDMA_DS = (1 << 1), /* disable EDMA; self-negated */
EDMA_RESET = (1 << 2), /* reset eng/trans/link/phy */
- EDMA_STATUS_OFS = 0x30, /* EDMA engine status */
+ EDMA_STATUS = 0x30, /* EDMA engine status */
EDMA_STATUS_CACHE_EMPTY = (1 << 6), /* GenIIe command cache empty */
EDMA_STATUS_IDLE = (1 << 7), /* GenIIe EDMA enabled/idle */
- EDMA_IORDY_TMOUT_OFS = 0x34,
- EDMA_ARB_CFG_OFS = 0x38,
+ EDMA_IORDY_TMOUT = 0x34,
+ EDMA_ARB_CFG = 0x38,
- EDMA_HALTCOND_OFS = 0x60, /* GenIIe halt conditions */
- EDMA_UNKNOWN_RSVD_OFS = 0x6C, /* GenIIe unknown/reserved */
+ EDMA_HALTCOND = 0x60, /* GenIIe halt conditions */
+ EDMA_UNKNOWN_RSVD = 0x6C, /* GenIIe unknown/reserved */
- BMDMA_CMD_OFS = 0x224, /* bmdma command register */
- BMDMA_STATUS_OFS = 0x228, /* bmdma status register */
- BMDMA_PRD_LOW_OFS = 0x22c, /* bmdma PRD addr 31:0 */
- BMDMA_PRD_HIGH_OFS = 0x230, /* bmdma PRD addr 63:32 */
+ BMDMA_CMD = 0x224, /* bmdma command register */
+ BMDMA_STATUS = 0x228, /* bmdma status register */
+ BMDMA_PRD_LOW = 0x22c, /* bmdma PRD addr 31:0 */
+ BMDMA_PRD_HIGH = 0x230, /* bmdma PRD addr 63:32 */
/* Host private flags (hp_flags) */
MV_HP_FLAG_MSI = (1 << 0),
@@ -534,8 +541,8 @@ struct mv_host_priv {
void __iomem *base;
void __iomem *main_irq_cause_addr;
void __iomem *main_irq_mask_addr;
- u32 irq_cause_ofs;
- u32 irq_mask_ofs;
+ u32 irq_cause_offset;
+ u32 irq_mask_offset;
u32 unmask_all_irqs;
/*
* These consistent DMA memory pools give us guaranteed
@@ -694,49 +701,49 @@ static struct ata_port_operations mv_iie_ops = {
static const struct ata_port_info mv_port_info[] = {
{ /* chip_504x */
.flags = MV_GEN_I_FLAGS,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_508x */
.flags = MV_GEN_I_FLAGS | MV_FLAG_DUAL_HC,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_5080 */
.flags = MV_GEN_I_FLAGS | MV_FLAG_DUAL_HC,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_604x */
.flags = MV_GEN_II_FLAGS,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &mv6_ops,
},
{ /* chip_608x */
.flags = MV_GEN_II_FLAGS | MV_FLAG_DUAL_HC,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &mv6_ops,
},
{ /* chip_6042 */
.flags = MV_GEN_IIE_FLAGS,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
{ /* chip_7042 */
.flags = MV_GEN_IIE_FLAGS,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
{ /* chip_soc */
.flags = MV_GEN_IIE_FLAGS,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
@@ -840,7 +847,7 @@ static inline unsigned int mv_hardport_from_port(unsigned int port)
static inline void __iomem *mv_hc_base(void __iomem *base, unsigned int hc)
{
- return (base + MV_SATAHC0_REG_BASE + (hc * MV_SATAHC_REG_SZ));
+ return (base + SATAHC0_REG_BASE + (hc * MV_SATAHC_REG_SZ));
}
static inline void __iomem *mv_hc_base_from_port(void __iomem *base,
@@ -895,10 +902,10 @@ static void mv_save_cached_regs(struct ata_port *ap)
void __iomem *port_mmio = mv_ap_base(ap);
struct mv_port_priv *pp = ap->private_data;
- pp->cached.fiscfg = readl(port_mmio + FISCFG_OFS);
- pp->cached.ltmode = readl(port_mmio + LTMODE_OFS);
- pp->cached.haltcond = readl(port_mmio + EDMA_HALTCOND_OFS);
- pp->cached.unknown_rsvd = readl(port_mmio + EDMA_UNKNOWN_RSVD_OFS);
+ pp->cached.fiscfg = readl(port_mmio + FISCFG);
+ pp->cached.ltmode = readl(port_mmio + LTMODE);
+ pp->cached.haltcond = readl(port_mmio + EDMA_HALTCOND);
+ pp->cached.unknown_rsvd = readl(port_mmio + EDMA_UNKNOWN_RSVD);
}
/**
@@ -913,8 +920,26 @@ static void mv_save_cached_regs(struct ata_port *ap)
static inline void mv_write_cached_reg(void __iomem *addr, u32 *old, u32 new)
{
if (new != *old) {
+ unsigned long laddr;
*old = new;
- writel(new, addr);
+ /*
+ * Workaround for 88SX60x1-B2 FEr SATA#13:
+ * Read-after-write is needed to prevent generating 64-bit
+ * write cycles on the PCI bus for SATA interface registers
+ * at offsets ending in 0x4 or 0xc.
+ *
+ * Looks like a lot of fuss, but it avoids an unnecessary
+ * +1 usec read-after-write delay for unaffected registers.
+ */
+ laddr = (long)addr & 0xffff;
+ if (laddr >= 0x300 && laddr <= 0x33c) {
+ laddr &= 0x000f;
+ if (laddr == 0x4 || laddr == 0xc) {
+ writelfl(new, addr); /* read after write */
+ return;
+ }
+ }
+ writel(new, addr); /* unaffected by the errata */
}
}
@@ -931,10 +956,10 @@ static void mv_set_edma_ptrs(void __iomem *port_mmio,
index = pp->req_idx << EDMA_REQ_Q_PTR_SHIFT;
WARN_ON(pp->crqb_dma & 0x3ff);
- writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI_OFS);
+ writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI);
writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | index,
- port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
- writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
+ port_mmio + EDMA_REQ_Q_IN_PTR);
+ writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR);
/*
* initialize response queue
@@ -943,10 +968,10 @@ static void mv_set_edma_ptrs(void __iomem *port_mmio,
index = pp->resp_idx << EDMA_RSP_Q_PTR_SHIFT;
WARN_ON(pp->crpb_dma & 0xff);
- writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI_OFS);
- writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
+ writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI);
+ writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR);
writelfl((pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK) | index,
- port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
+ port_mmio + EDMA_RSP_Q_OUT_PTR);
}
static void mv_write_main_irq_mask(u32 mask, struct mv_host_priv *hpriv)
@@ -1004,15 +1029,15 @@ static void mv_clear_and_enable_port_irqs(struct ata_port *ap,
u32 hc_irq_cause;
/* clear EDMA event indicators, if any */
- writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+ writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE);
/* clear pending irq events */
hc_irq_cause = ~((DEV_IRQ | DMA_IRQ) << hardport);
- writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
+ writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE);
/* clear FIS IRQ Cause */
if (IS_GEN_IIE(hpriv))
- writelfl(0, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
+ writelfl(0, port_mmio + FIS_IRQ_CAUSE);
mv_enable_port_irqs(ap, port_irqs);
}
@@ -1048,10 +1073,10 @@ static void mv_set_irq_coalescing(struct ata_host *host,
* GEN_II/GEN_IIE with dual host controllers:
* one set of global thresholds for the entire chip.
*/
- writel(clks, mmio + MV_IRQ_COAL_TIME_THRESHOLD);
- writel(count, mmio + MV_IRQ_COAL_IO_THRESHOLD);
+ writel(clks, mmio + IRQ_COAL_TIME_THRESHOLD);
+ writel(count, mmio + IRQ_COAL_IO_THRESHOLD);
/* clear leftover coal IRQ bit */
- writel(~ALL_PORTS_COAL_IRQ, mmio + MV_IRQ_COAL_CAUSE);
+ writel(~ALL_PORTS_COAL_IRQ, mmio + IRQ_COAL_CAUSE);
if (count)
coal_enable = ALL_PORTS_COAL_DONE;
clks = count = 0; /* force clearing of regular regs below */
@@ -1061,16 +1086,16 @@ static void mv_set_irq_coalescing(struct ata_host *host,
* All chips: independent thresholds for each HC on the chip.
*/
hc_mmio = mv_hc_base_from_port(mmio, 0);
- writel(clks, hc_mmio + HC_IRQ_COAL_TIME_THRESHOLD_OFS);
- writel(count, hc_mmio + HC_IRQ_COAL_IO_THRESHOLD_OFS);
- writel(~HC_COAL_IRQ, hc_mmio + HC_IRQ_CAUSE_OFS);
+ writel(clks, hc_mmio + HC_IRQ_COAL_TIME_THRESHOLD);
+ writel(count, hc_mmio + HC_IRQ_COAL_IO_THRESHOLD);
+ writel(~HC_COAL_IRQ, hc_mmio + HC_IRQ_CAUSE);
if (count)
coal_enable |= PORTS_0_3_COAL_DONE;
if (is_dual_hc) {
hc_mmio = mv_hc_base_from_port(mmio, MV_PORTS_PER_HC);
- writel(clks, hc_mmio + HC_IRQ_COAL_TIME_THRESHOLD_OFS);
- writel(count, hc_mmio + HC_IRQ_COAL_IO_THRESHOLD_OFS);
- writel(~HC_COAL_IRQ, hc_mmio + HC_IRQ_CAUSE_OFS);
+ writel(clks, hc_mmio + HC_IRQ_COAL_TIME_THRESHOLD);
+ writel(count, hc_mmio + HC_IRQ_COAL_IO_THRESHOLD);
+ writel(~HC_COAL_IRQ, hc_mmio + HC_IRQ_CAUSE);
if (count)
coal_enable |= PORTS_4_7_COAL_DONE;
}
@@ -1108,7 +1133,7 @@ static void mv_start_edma(struct ata_port *ap, void __iomem *port_mmio,
mv_set_edma_ptrs(port_mmio, hpriv, pp);
mv_clear_and_enable_port_irqs(ap, port_mmio, DONE_IRQ|ERR_IRQ);
- writelfl(EDMA_EN, port_mmio + EDMA_CMD_OFS);
+ writelfl(EDMA_EN, port_mmio + EDMA_CMD);
pp->pp_flags |= MV_PP_FLAG_EDMA_EN;
}
}
@@ -1128,7 +1153,7 @@ static void mv_wait_for_edma_empty_idle(struct ata_port *ap)
* as a rough guess at what even more drives might require.
*/
for (i = 0; i < timeout; ++i) {
- u32 edma_stat = readl(port_mmio + EDMA_STATUS_OFS);
+ u32 edma_stat = readl(port_mmio + EDMA_STATUS);
if ((edma_stat & empty_idle) == empty_idle)
break;
udelay(per_loop);
@@ -1148,11 +1173,11 @@ static int mv_stop_edma_engine(void __iomem *port_mmio)
int i;
/* Disable eDMA. The disable bit auto clears. */
- writelfl(EDMA_DS, port_mmio + EDMA_CMD_OFS);
+ writelfl(EDMA_DS, port_mmio + EDMA_CMD);
/* Wait for the chip to confirm eDMA is off. */
for (i = 10000; i > 0; i--) {
- u32 reg = readl(port_mmio + EDMA_CMD_OFS);
+ u32 reg = readl(port_mmio + EDMA_CMD);
if (!(reg & EDMA_EN))
return 0;
udelay(10);
@@ -1262,10 +1287,10 @@ static unsigned int mv_scr_offset(unsigned int sc_reg_in)
case SCR_STATUS:
case SCR_CONTROL:
case SCR_ERROR:
- ofs = SATA_STATUS_OFS + (sc_reg_in * sizeof(u32));
+ ofs = SATA_STATUS + (sc_reg_in * sizeof(u32));
break;
case SCR_ACTIVE:
- ofs = SATA_ACTIVE_OFS; /* active is not with the others */
+ ofs = SATA_ACTIVE; /* active is not with the others */
break;
default:
ofs = 0xffffffffU;
@@ -1290,7 +1315,25 @@ static int mv_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val)
unsigned int ofs = mv_scr_offset(sc_reg_in);
if (ofs != 0xffffffffU) {
- writelfl(val, mv_ap_base(link->ap) + ofs);
+ void __iomem *addr = mv_ap_base(link->ap) + ofs;
+ if (sc_reg_in == SCR_CONTROL) {
+ /*
+ * Workaround for 88SX60x1 FEr SATA#26:
+ *
+ * COMRESETs have to take care not to accidently
+ * put the drive to sleep when writing SCR_CONTROL.
+ * Setting bits 12..15 prevents this problem.
+ *
+ * So if we see an outbound COMMRESET, set those bits.
+ * Ditto for the followup write that clears the reset.
+ *
+ * The proprietary driver does this for
+ * all chip versions, and so do we.
+ */
+ if ((val & 0xf) == 1 || (readl(addr) & 0xf) == 1)
+ val |= 0xf000;
+ }
+ writelfl(val, addr);
return 0;
} else
return -EINVAL;
@@ -1368,9 +1411,9 @@ static void mv_config_fbs(struct ata_port *ap, int want_ncq, int want_fbs)
}
port_mmio = mv_ap_base(ap);
- mv_write_cached_reg(port_mmio + FISCFG_OFS, old_fiscfg, fiscfg);
- mv_write_cached_reg(port_mmio + LTMODE_OFS, old_ltmode, ltmode);
- mv_write_cached_reg(port_mmio + EDMA_HALTCOND_OFS, old_haltcond, haltcond);
+ mv_write_cached_reg(port_mmio + FISCFG, old_fiscfg, fiscfg);
+ mv_write_cached_reg(port_mmio + LTMODE, old_ltmode, ltmode);
+ mv_write_cached_reg(port_mmio + EDMA_HALTCOND, old_haltcond, haltcond);
}
static void mv_60x1_errata_sata25(struct ata_port *ap, int want_ncq)
@@ -1379,13 +1422,13 @@ static void mv_60x1_errata_sata25(struct ata_port *ap, int want_ncq)
u32 old, new;
/* workaround for 88SX60x1 FEr SATA#25 (part 1) */
- old = readl(hpriv->base + MV_GPIO_PORT_CTL_OFS);
+ old = readl(hpriv->base + GPIO_PORT_CTL);
if (want_ncq)
new = old | (1 << 22);
else
new = old & ~(1 << 22);
if (new != old)
- writel(new, hpriv->base + MV_GPIO_PORT_CTL_OFS);
+ writel(new, hpriv->base + GPIO_PORT_CTL);
}
/**
@@ -1409,7 +1452,7 @@ static void mv_bmdma_enable_iie(struct ata_port *ap, int enable_bmdma)
new = *old | 1;
else
new = *old & ~1;
- mv_write_cached_reg(mv_ap_base(ap) + EDMA_UNKNOWN_RSVD_OFS, old, new);
+ mv_write_cached_reg(mv_ap_base(ap) + EDMA_UNKNOWN_RSVD, old, new);
}
/*
@@ -1437,8 +1480,8 @@ static void mv_soc_led_blink_enable(struct ata_port *ap)
return;
hpriv->hp_flags |= MV_HP_QUIRK_LED_BLINK_EN;
hc_mmio = mv_hc_base_from_port(mv_host_base(host), ap->port_no);
- led_ctrl = readl(hc_mmio + SOC_LED_CTRL_OFS);
- writel(led_ctrl | SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL_OFS);
+ led_ctrl = readl(hc_mmio + SOC_LED_CTRL);
+ writel(led_ctrl | SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL);
}
static void mv_soc_led_blink_disable(struct ata_port *ap)
@@ -1463,8 +1506,8 @@ static void mv_soc_led_blink_disable(struct ata_port *ap)
hpriv->hp_flags &= ~MV_HP_QUIRK_LED_BLINK_EN;
hc_mmio = mv_hc_base_from_port(mv_host_base(host), ap->port_no);
- led_ctrl = readl(hc_mmio + SOC_LED_CTRL_OFS);
- writel(led_ctrl & ~SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL_OFS);
+ led_ctrl = readl(hc_mmio + SOC_LED_CTRL);
+ writel(led_ctrl & ~SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL);
}
static void mv_edma_cfg(struct ata_port *ap, int want_ncq, int want_edma)
@@ -1528,7 +1571,7 @@ static void mv_edma_cfg(struct ata_port *ap, int want_ncq, int want_edma)
pp->pp_flags |= MV_PP_FLAG_NCQ_EN;
}
- writelfl(cfg, port_mmio + EDMA_CFG_OFS);
+ writelfl(cfg, port_mmio + EDMA_CFG);
}
static void mv_port_free_dma_mem(struct ata_port *ap)
@@ -1575,6 +1618,7 @@ static int mv_port_start(struct ata_port *ap)
struct device *dev = ap->host->dev;
struct mv_host_priv *hpriv = ap->host->private_data;
struct mv_port_priv *pp;
+ unsigned long flags;
int tag;
pp = devm_kzalloc(dev, sizeof(*pp), GFP_KERNEL);
@@ -1610,8 +1654,12 @@ static int mv_port_start(struct ata_port *ap)
pp->sg_tbl_dma[tag] = pp->sg_tbl_dma[0];
}
}
+
+ spin_lock_irqsave(ap->lock, flags);
mv_save_cached_regs(ap);
mv_edma_cfg(ap, 0, 0);
+ spin_unlock_irqrestore(ap->lock, flags);
+
return 0;
out_port_free_dma_mem:
@@ -1630,8 +1678,12 @@ out_port_free_dma_mem:
*/
static void mv_port_stop(struct ata_port *ap)
{
+ unsigned long flags;
+
+ spin_lock_irqsave(ap->lock, flags);
mv_stop_edma(ap);
mv_enable_port_irqs(ap, 0);
+ spin_unlock_irqrestore(ap->lock, flags);
mv_port_free_dma_mem(ap);
}
@@ -1749,13 +1801,13 @@ static void mv_bmdma_setup(struct ata_queued_cmd *qc)
mv_fill_sg(qc);
/* clear all DMA cmd bits */
- writel(0, port_mmio + BMDMA_CMD_OFS);
+ writel(0, port_mmio + BMDMA_CMD);
/* load PRD table addr. */
writel((pp->sg_tbl_dma[qc->tag] >> 16) >> 16,
- port_mmio + BMDMA_PRD_HIGH_OFS);
+ port_mmio + BMDMA_PRD_HIGH);
writelfl(pp->sg_tbl_dma[qc->tag],
- port_mmio + BMDMA_PRD_LOW_OFS);
+ port_mmio + BMDMA_PRD_LOW);
/* issue r/w command */
ap->ops->sff_exec_command(ap, &qc->tf);
@@ -1776,7 +1828,7 @@ static void mv_bmdma_start(struct ata_queued_cmd *qc)
u32 cmd = (rw ? 0 : ATA_DMA_WR) | ATA_DMA_START;
/* start host DMA transaction */
- writelfl(cmd, port_mmio + BMDMA_CMD_OFS);
+ writelfl(cmd, port_mmio + BMDMA_CMD);
}
/**
@@ -1795,9 +1847,9 @@ static void mv_bmdma_stop(struct ata_queued_cmd *qc)
u32 cmd;
/* clear start/stop bit */
- cmd = readl(port_mmio + BMDMA_CMD_OFS);
+ cmd = readl(port_mmio + BMDMA_CMD);
cmd &= ~ATA_DMA_START;
- writelfl(cmd, port_mmio + BMDMA_CMD_OFS);
+ writelfl(cmd, port_mmio + BMDMA_CMD);
/* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */
ata_sff_dma_pause(ap);
@@ -1821,7 +1873,7 @@ static u8 mv_bmdma_status(struct ata_port *ap)
* Other bits are valid only if ATA_DMA_ACTIVE==0,
* and the ATA_DMA_INTR bit doesn't exist.
*/
- reg = readl(port_mmio + BMDMA_STATUS_OFS);
+ reg = readl(port_mmio + BMDMA_STATUS);
if (reg & ATA_DMA_ACTIVE)
status = ATA_DMA_ACTIVE;
else
@@ -2029,28 +2081,28 @@ static unsigned int mv_send_fis(struct ata_port *ap, u32 *fis, int nwords)
int i, timeout = 200, final_word = nwords - 1;
/* Initiate FIS transmission mode */
- old_ifctl = readl(port_mmio + SATA_IFCTL_OFS);
+ old_ifctl = readl(port_mmio + SATA_IFCTL);
ifctl = 0x100 | (old_ifctl & 0xf);
- writelfl(ifctl, port_mmio + SATA_IFCTL_OFS);
+ writelfl(ifctl, port_mmio + SATA_IFCTL);
/* Send all words of the FIS except for the final word */
for (i = 0; i < final_word; ++i)
- writel(fis[i], port_mmio + VENDOR_UNIQUE_FIS_OFS);
+ writel(fis[i], port_mmio + VENDOR_UNIQUE_FIS);
/* Flag end-of-transmission, and then send the final word */
- writelfl(ifctl | 0x200, port_mmio + SATA_IFCTL_OFS);
- writelfl(fis[final_word], port_mmio + VENDOR_UNIQUE_FIS_OFS);
+ writelfl(ifctl | 0x200, port_mmio + SATA_IFCTL);
+ writelfl(fis[final_word], port_mmio + VENDOR_UNIQUE_FIS);
/*
* Wait for FIS transmission to complete.
* This typically takes just a single iteration.
*/
do {
- ifstat = readl(port_mmio + SATA_IFSTAT_OFS);
+ ifstat = readl(port_mmio + SATA_IFSTAT);
} while (!(ifstat & 0x1000) && --timeout);
/* Restore original port configuration */
- writelfl(old_ifctl, port_mmio + SATA_IFCTL_OFS);
+ writelfl(old_ifctl, port_mmio + SATA_IFCTL);
/* See if it worked */
if ((ifstat & 0x3000) != 0x1000) {
@@ -2148,7 +2200,7 @@ static unsigned int mv_qc_issue(struct ata_queued_cmd *qc)
/* Write the request in pointer to kick the EDMA to life */
writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | in_index,
- port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
+ port_mmio + EDMA_REQ_Q_IN_PTR);
return 0;
case ATA_PROT_PIO:
@@ -2259,7 +2311,7 @@ static unsigned int mv_get_err_pmp_map(struct ata_port *ap)
{
void __iomem *port_mmio = mv_ap_base(ap);
- return readl(port_mmio + SATA_TESTCTL_OFS) >> 16;
+ return readl(port_mmio + SATA_TESTCTL) >> 16;
}
static void mv_pmp_eh_prep(struct ata_port *ap, unsigned int pmp_map)
@@ -2292,9 +2344,9 @@ static int mv_req_q_empty(struct ata_port *ap)
void __iomem *port_mmio = mv_ap_base(ap);
u32 in_ptr, out_ptr;
- in_ptr = (readl(port_mmio + EDMA_REQ_Q_IN_PTR_OFS)
+ in_ptr = (readl(port_mmio + EDMA_REQ_Q_IN_PTR)
>> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
- out_ptr = (readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS)
+ out_ptr = (readl(port_mmio + EDMA_REQ_Q_OUT_PTR)
>> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
return (in_ptr == out_ptr); /* 1 == queue_is_empty */
}
@@ -2456,12 +2508,12 @@ static void mv_err_intr(struct ata_port *ap)
sata_scr_read(&ap->link, SCR_ERROR, &serr);
sata_scr_write_flush(&ap->link, SCR_ERROR, serr);
- edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+ edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE);
if (IS_GEN_IIE(hpriv) && (edma_err_cause & EDMA_ERR_TRANS_IRQ_7)) {
- fis_cause = readl(port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
- writelfl(~fis_cause, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
+ fis_cause = readl(port_mmio + FIS_IRQ_CAUSE);
+ writelfl(~fis_cause, port_mmio + FIS_IRQ_CAUSE);
}
- writelfl(~edma_err_cause, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+ writelfl(~edma_err_cause, port_mmio + EDMA_ERR_IRQ_CAUSE);
if (edma_err_cause & EDMA_ERR_DEV) {
/*
@@ -2479,7 +2531,7 @@ static void mv_err_intr(struct ata_port *ap)
if (IS_GEN_IIE(hpriv) && (edma_err_cause & EDMA_ERR_TRANS_IRQ_7)) {
ata_ehi_push_desc(ehi, "fis_cause=%08x", fis_cause);
- if (fis_cause & SATA_FIS_IRQ_AN) {
+ if (fis_cause & FIS_IRQ_CAUSE_AN) {
u32 ec = edma_err_cause &
~(EDMA_ERR_TRANS_IRQ_7 | EDMA_ERR_IRQ_TRANSIENT);
sata_async_notification(ap);
@@ -2581,7 +2633,7 @@ static void mv_process_crpb_response(struct ata_port *ap,
u16 edma_status = le16_to_cpu(response->flags);
/*
* edma_status from a response queue entry:
- * LSB is from EDMA_ERR_IRQ_CAUSE_OFS (non-NCQ only).
+ * LSB is from EDMA_ERR_IRQ_CAUSE (non-NCQ only).
* MSB is saved ATA status from command completion.
*/
if (!ncq_enabled) {
@@ -2613,7 +2665,7 @@ static void mv_process_crpb_entries(struct ata_port *ap, struct mv_port_priv *pp
int ncq_enabled = (pp->pp_flags & MV_PP_FLAG_NCQ_EN);
/* Get the hardware queue position index */
- in_index = (readl(port_mmio + EDMA_RSP_Q_IN_PTR_OFS)
+ in_index = (readl(port_mmio + EDMA_RSP_Q_IN_PTR)
>> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
/* Process new responses from since the last time we looked */
@@ -2638,7 +2690,7 @@ static void mv_process_crpb_entries(struct ata_port *ap, struct mv_port_priv *pp
if (work_done)
writelfl((pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK) |
(pp->resp_idx << EDMA_RSP_Q_PTR_SHIFT),
- port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
+ port_mmio + EDMA_RSP_Q_OUT_PTR);
}
static void mv_port_intr(struct ata_port *ap, u32 port_cause)
@@ -2695,7 +2747,7 @@ static int mv_host_intr(struct ata_host *host, u32 main_irq_cause)
/* If asserted, clear the "all ports" IRQ coalescing bit */
if (main_irq_cause & ALL_PORTS_COAL_DONE)
- writel(~ALL_PORTS_COAL_IRQ, mmio + MV_IRQ_COAL_CAUSE);
+ writel(~ALL_PORTS_COAL_IRQ, mmio + IRQ_COAL_CAUSE);
for (port = 0; port < hpriv->n_ports; port++) {
struct ata_port *ap = host->ports[port];
@@ -2739,7 +2791,7 @@ static int mv_host_intr(struct ata_host *host, u32 main_irq_cause)
ack_irqs |= (DMA_IRQ | DEV_IRQ) << p;
}
hc_mmio = mv_hc_base_from_port(mmio, port);
- writelfl(~ack_irqs, hc_mmio + HC_IRQ_CAUSE_OFS);
+ writelfl(~ack_irqs, hc_mmio + HC_IRQ_CAUSE);
handled = 1;
}
/*
@@ -2761,7 +2813,7 @@ static int mv_pci_error(struct ata_host *host, void __iomem *mmio)
unsigned int i, err_mask, printed = 0;
u32 err_cause;
- err_cause = readl(mmio + hpriv->irq_cause_ofs);
+ err_cause = readl(mmio + hpriv->irq_cause_offset);
dev_printk(KERN_ERR, host->dev, "PCI ERROR; PCI IRQ cause=0x%08x\n",
err_cause);
@@ -2769,7 +2821,7 @@ static int mv_pci_error(struct ata_host *host, void __iomem *mmio)
DPRINTK("All regs @ PCI error\n");
mv_dump_all_regs(mmio, -1, to_pci_dev(host->dev));
- writelfl(0, mmio + hpriv->irq_cause_ofs);
+ writelfl(0, mmio + hpriv->irq_cause_offset);
for (i = 0; i < host->n_ports; i++) {
ap = host->ports[i];
@@ -2906,7 +2958,7 @@ static void mv5_reset_bus(struct ata_host *host, void __iomem *mmio)
static void mv5_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio)
{
- writel(0x0fcfffff, mmio + MV_FLASH_CTL_OFS);
+ writel(0x0fcfffff, mmio + FLASH_CTL);
}
static void mv5_read_preamp(struct mv_host_priv *hpriv, int idx,
@@ -2925,7 +2977,7 @@ static void mv5_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio)
{
u32 tmp;
- writel(0, mmio + MV_GPIO_PORT_CTL_OFS);
+ writel(0, mmio + GPIO_PORT_CTL);
/* FIXME: handle MV_HP_ERRATA_50XXB2 errata */
@@ -2943,14 +2995,14 @@ static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
int fix_apm_sq = (hpriv->hp_flags & MV_HP_ERRATA_50XXB0);
if (fix_apm_sq) {
- tmp = readl(phy_mmio + MV5_LTMODE_OFS);
+ tmp = readl(phy_mmio + MV5_LTMODE);
tmp |= (1 << 19);
- writel(tmp, phy_mmio + MV5_LTMODE_OFS);
+ writel(tmp, phy_mmio + MV5_LTMODE);
- tmp = readl(phy_mmio + MV5_PHY_CTL_OFS);
+ tmp = readl(phy_mmio + MV5_PHY_CTL);
tmp &= ~0x3;
tmp |= 0x1;
- writel(tmp, phy_mmio + MV5_PHY_CTL_OFS);
+ writel(tmp, phy_mmio + MV5_PHY_CTL);
}
tmp = readl(phy_mmio + MV5_PHY_MODE);
@@ -2971,7 +3023,7 @@ static void mv5_reset_hc_port(struct mv_host_priv *hpriv, void __iomem *mmio,
mv_reset_channel(hpriv, mmio, port);
ZERO(0x028); /* command */
- writel(0x11f, port_mmio + EDMA_CFG_OFS);
+ writel(0x11f, port_mmio + EDMA_CFG);
ZERO(0x004); /* timer */
ZERO(0x008); /* irq err cause */
ZERO(0x00c); /* irq err mask */
@@ -2982,7 +3034,7 @@ static void mv5_reset_hc_port(struct mv_host_priv *hpriv, void __iomem *mmio,
ZERO(0x024); /* respq outp */
ZERO(0x020); /* respq inp */
ZERO(0x02c); /* test control */
- writel(0xbc, port_mmio + EDMA_IORDY_TMOUT_OFS);
+ writel(0xbc, port_mmio + EDMA_IORDY_TMOUT);
}
#undef ZERO
@@ -3028,16 +3080,16 @@ static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio)
struct mv_host_priv *hpriv = host->private_data;
u32 tmp;
- tmp = readl(mmio + MV_PCI_MODE_OFS);
+ tmp = readl(mmio + MV_PCI_MODE);
tmp &= 0xff00ffff;
- writel(tmp, mmio + MV_PCI_MODE_OFS);
+ writel(tmp, mmio + MV_PCI_MODE);
ZERO(MV_PCI_DISC_TIMER);
ZERO(MV_PCI_MSI_TRIGGER);
- writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT_OFS);
+ writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT);
ZERO(MV_PCI_SERR_MASK);
- ZERO(hpriv->irq_cause_ofs);
- ZERO(hpriv->irq_mask_ofs);
+ ZERO(hpriv->irq_cause_offset);
+ ZERO(hpriv->irq_mask_offset);
ZERO(MV_PCI_ERR_LOW_ADDRESS);
ZERO(MV_PCI_ERR_HIGH_ADDRESS);
ZERO(MV_PCI_ERR_ATTRIBUTE);
@@ -3051,10 +3103,10 @@ static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio)
mv5_reset_flash(hpriv, mmio);
- tmp = readl(mmio + MV_GPIO_PORT_CTL_OFS);
+ tmp = readl(mmio + GPIO_PORT_CTL);
tmp &= 0x3;
tmp |= (1 << 5) | (1 << 6);
- writel(tmp, mmio + MV_GPIO_PORT_CTL_OFS);
+ writel(tmp, mmio + GPIO_PORT_CTL);
}
/**
@@ -3069,7 +3121,7 @@ static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio)
static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int n_hc)
{
- void __iomem *reg = mmio + PCI_MAIN_CMD_STS_OFS;
+ void __iomem *reg = mmio + PCI_MAIN_CMD_STS;
int i, rc = 0;
u32 t;
@@ -3127,7 +3179,7 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx,
void __iomem *port_mmio;
u32 tmp;
- tmp = readl(mmio + MV_RESET_CFG_OFS);
+ tmp = readl(mmio + RESET_CFG);
if ((tmp & (1 << 0)) == 0) {
hpriv->signal[idx].amps = 0x7 << 8;
hpriv->signal[idx].pre = 0x1 << 5;
@@ -3143,7 +3195,7 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx,
static void mv6_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio)
{
- writel(0x00000060, mmio + MV_GPIO_PORT_CTL_OFS);
+ writel(0x00000060, mmio + GPIO_PORT_CTL);
}
static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
@@ -3201,6 +3253,7 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
* Workaround for 60x1-B2 errata SATA#13:
* Any write to PHY_MODE4 (above) may corrupt PHY_MODE3,
* so we must always rewrite PHY_MODE3 after PHY_MODE4.
+ * Or ensure we use writelfl() when writing PHY_MODE4.
*/
writel(m3, port_mmio + PHY_MODE3);
@@ -3252,7 +3305,7 @@ static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv,
mv_reset_channel(hpriv, mmio, port);
ZERO(0x028); /* command */
- writel(0x101f, port_mmio + EDMA_CFG_OFS);
+ writel(0x101f, port_mmio + EDMA_CFG);
ZERO(0x004); /* timer */
ZERO(0x008); /* irq err cause */
ZERO(0x00c); /* irq err mask */
@@ -3263,7 +3316,7 @@ static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv,
ZERO(0x024); /* respq outp */
ZERO(0x020); /* respq inp */
ZERO(0x02c); /* test control */
- writel(0xbc, port_mmio + EDMA_IORDY_TMOUT_OFS);
+ writel(0xbc, port_mmio + EDMA_IORDY_TMOUT);
}
#undef ZERO
@@ -3308,12 +3361,12 @@ static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio)
static void mv_setup_ifcfg(void __iomem *port_mmio, int want_gen2i)
{
- u32 ifcfg = readl(port_mmio + SATA_INTERFACE_CFG_OFS);
+ u32 ifcfg = readl(port_mmio + SATA_IFCFG);
ifcfg = (ifcfg & 0xf7f) | 0x9b1000; /* from chip spec */
if (want_gen2i)
ifcfg |= (1 << 7); /* enable gen2i speed */
- writelfl(ifcfg, port_mmio + SATA_INTERFACE_CFG_OFS);
+ writelfl(ifcfg, port_mmio + SATA_IFCFG);
}
static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio,
@@ -3327,7 +3380,7 @@ static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio,
* to disable the EDMA engine before doing the EDMA_RESET operation.
*/
mv_stop_edma_engine(port_mmio);
- writelfl(EDMA_RESET, port_mmio + EDMA_CMD_OFS);
+ writelfl(EDMA_RESET, port_mmio + EDMA_CMD);
if (!IS_GEN_I(hpriv)) {
/* Enable 3.0gb/s link speed: this survives EDMA_RESET */
@@ -3336,11 +3389,11 @@ static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio,
/*
* Strobing EDMA_RESET here causes a hard reset of the SATA transport,
* link, and physical layers. It resets all SATA interface registers
- * (except for SATA_INTERFACE_CFG), and issues a COMRESET to the dev.
+ * (except for SATA_IFCFG), and issues a COMRESET to the dev.
*/
- writelfl(EDMA_RESET, port_mmio + EDMA_CMD_OFS);
+ writelfl(EDMA_RESET, port_mmio + EDMA_CMD);
udelay(25); /* allow reset propagation */
- writelfl(0, port_mmio + EDMA_CMD_OFS);
+ writelfl(0, port_mmio + EDMA_CMD);
hpriv->ops->phy_errata(hpriv, mmio, port_no);
@@ -3352,12 +3405,12 @@ static void mv_pmp_select(struct ata_port *ap, int pmp)
{
if (sata_pmp_supported(ap)) {
void __iomem *port_mmio = mv_ap_base(ap);
- u32 reg = readl(port_mmio + SATA_IFCTL_OFS);
+ u32 reg = readl(port_mmio + SATA_IFCTL);
int old = reg & 0xf;
if (old != pmp) {
reg = (reg & ~0xf) | pmp;
- writelfl(reg, port_mmio + SATA_IFCTL_OFS);
+ writelfl(reg, port_mmio + SATA_IFCTL);
}
}
}
@@ -3432,11 +3485,11 @@ static void mv_eh_thaw(struct ata_port *ap)
u32 hc_irq_cause;
/* clear EDMA errors on this port */
- writel(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+ writel(0, port_mmio + EDMA_ERR_IRQ_CAUSE);
/* clear pending irq events */
hc_irq_cause = ~((DEV_IRQ | DMA_IRQ) << hardport);
- writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
+ writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE);
mv_enable_port_irqs(ap, ERR_IRQ);
}
@@ -3455,8 +3508,7 @@ static void mv_eh_thaw(struct ata_port *ap)
*/
static void mv_port_init(struct ata_ioports *port, void __iomem *port_mmio)
{
- void __iomem *shd_base = port_mmio + SHD_BLK_OFS;
- unsigned serr_ofs;
+ void __iomem *serr, *shd_base = port_mmio + SHD_BLK;
/* PIO related setup
*/
@@ -3471,23 +3523,23 @@ static void mv_port_init(struct ata_ioports *port, void __iomem *port_mmio)
port->status_addr =
port->command_addr = shd_base + (sizeof(u32) * ATA_REG_STATUS);
/* special case: control/altstatus doesn't have ATA_REG_ address */
- port->altstatus_addr = port->ctl_addr = shd_base + SHD_CTL_AST_OFS;
+ port->altstatus_addr = port->ctl_addr = shd_base + SHD_CTL_AST;
/* unused: */
port->cmd_addr = port->bmdma_addr = port->scr_addr = NULL;
/* Clear any currently outstanding port interrupt conditions */
- serr_ofs = mv_scr_offset(SCR_ERROR);
- writelfl(readl(port_mmio + serr_ofs), port_mmio + serr_ofs);
- writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+ serr = port_mmio + mv_scr_offset(SCR_ERROR);
+ writelfl(readl(serr), serr);
+ writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE);
/* unmask all non-transient EDMA error interrupts */
- writelfl(~EDMA_ERR_IRQ_TRANSIENT, port_mmio + EDMA_ERR_IRQ_MASK_OFS);
+ writelfl(~EDMA_ERR_IRQ_TRANSIENT, port_mmio + EDMA_ERR_IRQ_MASK);
VPRINTK("EDMA cfg=0x%08x EDMA IRQ err cause/mask=0x%08x/0x%08x\n",
- readl(port_mmio + EDMA_CFG_OFS),
- readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS),
- readl(port_mmio + EDMA_ERR_IRQ_MASK_OFS));
+ readl(port_mmio + EDMA_CFG),
+ readl(port_mmio + EDMA_ERR_IRQ_CAUSE),
+ readl(port_mmio + EDMA_ERR_IRQ_MASK));
}
static unsigned int mv_in_pcix_mode(struct ata_host *host)
@@ -3498,7 +3550,7 @@ static unsigned int mv_in_pcix_mode(struct ata_host *host)
if (IS_SOC(hpriv) || !IS_PCIE(hpriv))
return 0; /* not PCI-X capable */
- reg = readl(mmio + MV_PCI_MODE_OFS);
+ reg = readl(mmio + MV_PCI_MODE);
if ((reg & MV_PCI_MODE_MASK) == 0)
return 0; /* conventional PCI mode */
return 1; /* chip is in PCI-X mode */
@@ -3511,13 +3563,25 @@ static int mv_pci_cut_through_okay(struct ata_host *host)
u32 reg;
if (!mv_in_pcix_mode(host)) {
- reg = readl(mmio + PCI_COMMAND_OFS);
- if (reg & PCI_COMMAND_MRDTRIG)
+ reg = readl(mmio + MV_PCI_COMMAND);
+ if (reg & MV_PCI_COMMAND_MRDTRIG)
return 0; /* not okay */
}
return 1; /* okay */
}
+static void mv_60x1b2_errata_pci7(struct ata_host *host)
+{
+ struct mv_host_priv *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->base;
+
+ /* workaround for 60x1-B2 errata PCI#7 */
+ if (mv_in_pcix_mode(host)) {
+ u32 reg = readl(mmio + MV_PCI_COMMAND);
+ writelfl(reg & ~MV_PCI_COMMAND_MWRCOM, mmio + MV_PCI_COMMAND);
+ }
+}
+
static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
{
struct pci_dev *pdev = to_pci_dev(host->dev);
@@ -3571,6 +3635,7 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
switch (pdev->revision) {
case 0x7:
+ mv_60x1b2_errata_pci7(host);
hp_flags |= MV_HP_ERRATA_60X1B2;
break;
case 0x9:
@@ -3647,12 +3712,12 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
hpriv->hp_flags = hp_flags;
if (hp_flags & MV_HP_PCIE) {
- hpriv->irq_cause_ofs = PCIE_IRQ_CAUSE_OFS;
- hpriv->irq_mask_ofs = PCIE_IRQ_MASK_OFS;
+ hpriv->irq_cause_offset = PCIE_IRQ_CAUSE;
+ hpriv->irq_mask_offset = PCIE_IRQ_MASK;
hpriv->unmask_all_irqs = PCIE_UNMASK_ALL_IRQS;
} else {
- hpriv->irq_cause_ofs = PCI_IRQ_CAUSE_OFS;
- hpriv->irq_mask_ofs = PCI_IRQ_MASK_OFS;
+ hpriv->irq_cause_offset = PCI_IRQ_CAUSE;
+ hpriv->irq_mask_offset = PCI_IRQ_MASK;
hpriv->unmask_all_irqs = PCI_UNMASK_ALL_IRQS;
}
@@ -3681,11 +3746,11 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
goto done;
if (IS_SOC(hpriv)) {
- hpriv->main_irq_cause_addr = mmio + SOC_HC_MAIN_IRQ_CAUSE_OFS;
- hpriv->main_irq_mask_addr = mmio + SOC_HC_MAIN_IRQ_MASK_OFS;
+ hpriv->main_irq_cause_addr = mmio + SOC_HC_MAIN_IRQ_CAUSE;
+ hpriv->main_irq_mask_addr = mmio + SOC_HC_MAIN_IRQ_MASK;
} else {
- hpriv->main_irq_cause_addr = mmio + PCI_HC_MAIN_IRQ_CAUSE_OFS;
- hpriv->main_irq_mask_addr = mmio + PCI_HC_MAIN_IRQ_MASK_OFS;
+ hpriv->main_irq_cause_addr = mmio + PCI_HC_MAIN_IRQ_CAUSE;
+ hpriv->main_irq_mask_addr = mmio + PCI_HC_MAIN_IRQ_MASK;
}
/* initialize shadow irq mask with register's value */
@@ -3727,18 +3792,20 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
VPRINTK("HC%i: HC config=0x%08x HC IRQ cause "
"(before clear)=0x%08x\n", hc,
- readl(hc_mmio + HC_CFG_OFS),
- readl(hc_mmio + HC_IRQ_CAUSE_OFS));
+ readl(hc_mmio + HC_CFG),
+ readl(hc_mmio + HC_IRQ_CAUSE));
/* Clear any currently outstanding hc interrupt conditions */
- writelfl(0, hc_mmio + HC_IRQ_CAUSE_OFS);
+ writelfl(0, hc_mmio + HC_IRQ_CAUSE);
}
- /* Clear any currently outstanding host interrupt conditions */
- writelfl(0, mmio + hpriv->irq_cause_ofs);
+ if (!IS_SOC(hpriv)) {
+ /* Clear any currently outstanding host interrupt conditions */
+ writelfl(0, mmio + hpriv->irq_cause_offset);
- /* and unmask interrupt generation for host regs */
- writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_ofs);
+ /* and unmask interrupt generation for host regs */
+ writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_offset);
+ }
/*
* enable only global host interrupts for now.
@@ -3844,7 +3911,7 @@ static int mv_platform_probe(struct platform_device *pdev)
host->iomap = NULL;
hpriv->base = devm_ioremap(&pdev->dev, res->start,
res->end - res->start + 1);
- hpriv->base -= MV_SATAHC0_REG_BASE;
+ hpriv->base -= SATAHC0_REG_BASE;
/*
* (Re-)program MBUS remapping windows if we are asked to.
diff --git a/include/linux/ata.h b/include/linux/ata.h
index 6617c9f..cb79b7a 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -29,6 +29,8 @@
#ifndef __LINUX_ATA_H__
#define __LINUX_ATA_H__
+#include <linux/kernel.h>
+#include <linux/string.h>
#include <linux/types.h>
#include <asm/byteorder.h>
@@ -91,6 +93,7 @@ enum {
ATA_ID_CFA_POWER = 160,
ATA_ID_CFA_KEY_MGMT = 162,
ATA_ID_CFA_MODES = 163,
+ ATA_ID_DATA_SET_MGMT = 169,
ATA_ID_ROT_SPEED = 217,
ATA_ID_PIO4 = (1 << 1),
@@ -248,6 +251,7 @@ enum {
ATA_CMD_SMART = 0xB0,
ATA_CMD_MEDIA_LOCK = 0xDE,
ATA_CMD_MEDIA_UNLOCK = 0xDF,
+ ATA_CMD_DSM = 0x06,
/* marked obsolete in the ATA/ATAPI-7 spec */
ATA_CMD_RESTORE = 0x10,
@@ -321,6 +325,9 @@ enum {
ATA_SMART_READ_VALUES = 0xD0,
ATA_SMART_READ_THRESHOLDS = 0xD1,
+ /* feature values for Data Set Management */
+ ATA_DSM_TRIM = 0x01,
+
/* password used in LBA Mid / LBA High for executing SMART commands */
ATA_SMART_LBAM_PASS = 0x4F,
ATA_SMART_LBAH_PASS = 0xC2,
@@ -723,6 +730,14 @@ static inline int ata_id_has_unload(const u16 *id)
return 0;
}
+static inline int ata_id_has_trim(const u16 *id)
+{
+ if (ata_id_major_version(id) >= 7 &&
+ (id[ATA_ID_DATA_SET_MGMT] & 1))
+ return 1;
+ return 0;
+}
+
static inline int ata_id_current_chs_valid(const u16 *id)
{
/* For ATA-1 devices, if the INITIALIZE DEVICE PARAMETERS command
@@ -863,6 +878,32 @@ static inline void ata_id_to_hd_driveid(u16 *id)
#endif
}
+/*
+ * Write up to 'max' LBA Range Entries to the buffer that will cover the
+ * extent from sector to sector + count. This is used for TRIM and for
+ * ADD LBA(S) TO NV CACHE PINNED SET.
+ */
+static inline unsigned ata_set_lba_range_entries(void *_buffer, unsigned max,
+ u64 sector, unsigned long count)
+{
+ __le64 *buffer = _buffer;
+ unsigned i = 0;
+
+ while (i < max) {
+ u64 entry = sector |
+ ((u64)(count > 0xffff ? 0xffff : count) << 48);
+ buffer[i++] = __cpu_to_le64(entry);
+ if (count <= 0xffff)
+ break;
+ count -= 0xffff;
+ sector += 0xffff;
+ }
+
+ max = ALIGN(i * 8, 512);
+ memset(buffer + i, 0, max - i * 8);
+ return max;
+}
+
static inline int is_multi_taskfile(struct ata_taskfile *tf)
{
return (tf->command == ATA_CMD_READ_MULTI) ||
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2009-03-25 3:01 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2009-03-25 3:01 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
No major 2.6.29 fixes have cropped up so far, since release.
Summary, nothing highly notable:
- sata_mv: large update, include ATAPI support (previously thought impossible)
- core updates from Alan that should help with error handling on SFF hardware
- large "magic number" -> "named constant" cleanup
- other minor updates, see shortlog below
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/ahci.c | 31 +-
drivers/ata/ata_generic.c | 4 +-
drivers/ata/ata_piix.c | 60 ++--
drivers/ata/libata-core.c | 14 +-
drivers/ata/libata-eh.c | 19 +-
drivers/ata/libata-sff.c | 91 ++++-
drivers/ata/libata.h | 2 -
drivers/ata/pata_acpi.c | 6 +-
drivers/ata/pata_ali.c | 28 +-
drivers/ata/pata_amd.c | 70 ++--
drivers/ata/pata_artop.c | 49 ++-
drivers/ata/pata_at32.c | 4 +-
drivers/ata/pata_atiixp.c | 6 +-
drivers/ata/pata_bf54x.c | 2 +-
drivers/ata/pata_cmd640.c | 2 +-
drivers/ata/pata_cmd64x.c | 24 +-
drivers/ata/pata_cs5520.c | 2 +-
drivers/ata/pata_cs5530.c | 8 +-
drivers/ata/pata_cs5535.c | 4 +-
drivers/ata/pata_cs5536.c | 4 +-
drivers/ata/pata_cypress.c | 4 +-
drivers/ata/pata_efar.c | 6 +-
drivers/ata/pata_hpt366.c | 4 +-
drivers/ata/pata_hpt37x.c | 28 +-
drivers/ata/pata_hpt3x2n.c | 4 +-
drivers/ata/pata_hpt3x3.c | 6 +-
drivers/ata/pata_icside.c | 4 +-
drivers/ata/pata_isapnp.c | 14 +-
drivers/ata/pata_it8213.c | 4 +-
drivers/ata/pata_it821x.c | 16 +-
drivers/ata/pata_ixp4xx_cf.c | 2 +-
drivers/ata/pata_jmicron.c | 4 +-
drivers/ata/pata_legacy.c | 2 +-
drivers/ata/pata_marvell.c | 8 +-
drivers/ata/pata_mpc52xx.c | 4 +-
drivers/ata/pata_mpiix.c | 2 +-
drivers/ata/pata_netcell.c | 4 +-
drivers/ata/pata_ninja32.c | 2 +-
drivers/ata/pata_ns87410.c | 2 +-
drivers/ata/pata_ns87415.c | 8 +-
drivers/ata/pata_octeon_cf.c | 4 +-
drivers/ata/pata_oldpiix.c | 4 +-
drivers/ata/pata_opti.c | 2 +-
drivers/ata/pata_optidma.c | 10 +-
drivers/ata/pata_pcmcia.c | 36 ++-
drivers/ata/pata_pdc2027x.c | 12 +-
drivers/ata/pata_pdc202xx_old.c | 12 +-
drivers/ata/pata_qdi.c | 4 +-
drivers/ata/pata_radisys.c | 6 +-
drivers/ata/pata_rb532_cf.c | 64 +---
drivers/ata/pata_rz1000.c | 2 +-
drivers/ata/pata_sc1200.c | 35 ++-
drivers/ata/pata_scc.c | 4 +-
drivers/ata/pata_sch.c | 6 +-
drivers/ata/pata_serverworks.c | 20 +-
drivers/ata/pata_sil680.c | 8 +-
drivers/ata/pata_sis.c | 32 +-
drivers/ata/pata_sl82c105.c | 6 +-
drivers/ata/pata_triflex.c | 4 +-
drivers/ata/pata_via.c | 24 +-
drivers/ata/pata_winbond.c | 2 +-
drivers/ata/pdc_adma.c | 4 +-
drivers/ata/sata_fsl.c | 4 +-
drivers/ata/sata_inic162x.c | 4 +-
drivers/ata/sata_mv.c | 868 +++++++++++++++++++++++++++++++++------
drivers/ata/sata_nv.c | 7 +-
drivers/ata/sata_promise.c | 30 +-
drivers/ata/sata_qstor.c | 3 +-
drivers/ata/sata_sil.c | 16 +-
drivers/ata/sata_sil24.c | 18 +-
drivers/ata/sata_sis.c | 4 +-
drivers/ata/sata_svw.c | 16 +-
drivers/ata/sata_sx4.c | 4 +-
drivers/ata/sata_uli.c | 2 +-
drivers/ata/sata_via.c | 16 +-
drivers/ata/sata_vsc.c | 7 +-
include/linux/ata.h | 6 +
include/linux/libata.h | 8 +
78 files changed, 1330 insertions(+), 542 deletions(-)
Alan Cox (4):
pata_artop: Serializing support
pata_sc1200: Activate secondary channel
[libata] Drain data on errors
[libata] Improve timeout handling
David Milburn (1):
[libata] ahci: correct enclosure LED state save
Erik Inge Bolsø (4):
include/linux/ata.h: add some more transfer masks
[libata] convert drivers to use ata.h mode mask defines
pata_radisys: fix mwdma_mask to exclude mwdma0
pata_efar: fix *dma_mask
Florian Fainelli (1):
pata-rb532-cf: platform_get_irq() fix ignored failure
Maciej Rutecki (1):
ahci: Blacklist HP Compaq 6720s that spins off disks during ACPI power off
Mark Lord (19):
sata_mv: cleanup chipset GENeration FLAGS
sata_mv: rearrange mv_start_dma() and friends
sata_mv: restructure mv_qc_issue
sata_mv: update ata_qc_from_tag
sata_mv: mv_fill_sg fixes v2
sata_mv: introduce support for ATAPI devices
sata_mv: optimize use of mv_edma_cfg
sata_mv: remove leftovers
[libata] sata_mv: cache frequently-accessed registers
[libata] sata_mv: Enable use of (basic) DMA for ATAPI on GEN_IIE chips
[libata] sata_mv: Tighten up interrupt masking in mv_qc_issue()
[libata] sata_mv: Add a new mv_sff_check_status() function to sata_mv.
[libata] Export ata_pio_queue_task() so that it can be used from sata_mv.
[libata] sata_mv: Implement direct FIS transmission via mv_qc_issue_fis().
sata_mv: cosmetic preparations for IRQ coalescing
sata_mv: implement IRQ coalescing (v2)
sata_mv: optimize IRQ coalescing for 8-port chips
sata_mv: fix LED blinking for SoC+NCQ
[libata] More robust parsing for IDENTIFY DEVICE multi_count field
Phil Sutter (4):
pata-rb532-cf: replace rb532_pata_finish_io()
pata-rb532-cf: use ata_sff_exec_command()
pata-rb532-cf: use ata_sff_data_xfer32()
pata-rb532-cf: drop custom freeze and thaw
Tejun Heo (1):
ahci: drop intx manipulation on msi enable
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 66e012c..788bba2 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -404,7 +404,7 @@ static const struct ata_port_info ahci_port_info[] = {
/* board_ahci */
{
.flags = AHCI_FLAG_COMMON,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
@@ -412,7 +412,7 @@ static const struct ata_port_info ahci_port_info[] = {
{
AHCI_HFLAGS (AHCI_HFLAG_NO_NCQ | AHCI_HFLAG_NO_PMP),
.flags = AHCI_FLAG_COMMON,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_vt8251_ops,
},
@@ -420,7 +420,7 @@ static const struct ata_port_info ahci_port_info[] = {
{
AHCI_HFLAGS (AHCI_HFLAG_IGN_IRQ_IF_ERR),
.flags = AHCI_FLAG_COMMON,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
@@ -430,7 +430,7 @@ static const struct ata_port_info ahci_port_info[] = {
AHCI_HFLAG_32BIT_ONLY | AHCI_HFLAG_NO_MSI |
AHCI_HFLAG_SECT255),
.flags = AHCI_FLAG_COMMON,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_sb600_ops,
},
@@ -440,7 +440,7 @@ static const struct ata_port_info ahci_port_info[] = {
AHCI_HFLAG_MV_PATA | AHCI_HFLAG_NO_PMP),
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
@@ -448,7 +448,7 @@ static const struct ata_port_info ahci_port_info[] = {
{
AHCI_HFLAGS (AHCI_HFLAG_IGN_SERR_INTERNAL),
.flags = AHCI_FLAG_COMMON,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_sb600_ops,
},
@@ -456,7 +456,7 @@ static const struct ata_port_info ahci_port_info[] = {
{
AHCI_HFLAGS (AHCI_HFLAG_YES_NCQ),
.flags = AHCI_FLAG_COMMON,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
@@ -464,7 +464,7 @@ static const struct ata_port_info ahci_port_info[] = {
{
AHCI_HFLAGS (AHCI_HFLAG_NO_PMP),
.flags = AHCI_FLAG_COMMON,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
@@ -1348,7 +1348,7 @@ static ssize_t ahci_transmit_led_message(struct ata_port *ap, u32 state,
writel(message[1], mmio + hpriv->em_loc+4);
/* save off new led state for port/slot */
- emp->led_state = message[1];
+ emp->led_state = state;
/*
* tell hardware to transmit the message
@@ -2565,6 +2565,15 @@ static bool ahci_broken_system_poweroff(struct pci_dev *pdev)
/* PCI slot number of the controller */
.driver_data = (void *)0x1FUL,
},
+ {
+ .ident = "HP Compaq 6720s",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "HP Compaq 6720s"),
+ },
+ /* PCI slot number of the controller */
+ .driver_data = (void *)0x1FUL,
+ },
{ } /* terminate list */
};
@@ -2647,8 +2656,8 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (board_id == board_ahci_sb700 && pdev->revision >= 0x40)
hpriv->flags &= ~AHCI_HFLAG_IGN_SERR_INTERNAL;
- if ((hpriv->flags & AHCI_HFLAG_NO_MSI) || pci_enable_msi(pdev))
- pci_intx(pdev, 1);
+ if (!(hpriv->flags & AHCI_HFLAG_NO_MSI))
+ pci_enable_msi(pdev);
/* save initial config */
ahci_save_initial_config(pdev, hpriv);
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
index dc48a63..ecfd22b 100644
--- a/drivers/ata/ata_generic.c
+++ b/drivers/ata/ata_generic.c
@@ -118,8 +118,8 @@ static int ata_generic_init_one(struct pci_dev *dev, const struct pci_device_id
u16 command;
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &generic_port_ops
};
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index ef8b30d..e5cbe80 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -446,34 +446,34 @@ static struct ata_port_info piix_port_info[] = {
[piix_pata_mwdma] = /* PIIX3 MWDMA only */
{
.flags = PIIX_PATA_FLAGS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA12_ONLY, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
.port_ops = &piix_pata_ops,
},
[piix_pata_33] = /* PIIX4 at 33MHz */
{
.flags = PIIX_PATA_FLAGS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
- .udma_mask = ATA_UDMA_MASK_40C,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA12_ONLY, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
+ .udma_mask = ATA_UDMA2,
.port_ops = &piix_pata_ops,
},
[ich_pata_33] = /* ICH0 - ICH at 33Mhz*/
{
.flags = PIIX_PATA_FLAGS,
- .pio_mask = 0x1f, /* pio 0-4 */
- .mwdma_mask = 0x06, /* Check: maybe 0x07 */
- .udma_mask = ATA_UDMA2, /* UDMA33 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA12_ONLY, /* Check: maybe MWDMA0 is ok */
+ .udma_mask = ATA_UDMA2,
.port_ops = &ich_pata_ops,
},
[ich_pata_66] = /* ICH controllers up to 66MHz */
{
.flags = PIIX_PATA_FLAGS,
- .pio_mask = 0x1f, /* pio 0-4 */
- .mwdma_mask = 0x06, /* MWDMA0 is broken on chip */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA12_ONLY, /* MWDMA0 is broken on chip */
.udma_mask = ATA_UDMA4,
.port_ops = &ich_pata_ops,
},
@@ -481,17 +481,17 @@ static struct ata_port_info piix_port_info[] = {
[ich_pata_100] =
{
.flags = PIIX_PATA_FLAGS | PIIX_FLAG_CHECKINTR,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x06, /* mwdma1-2 */
- .udma_mask = ATA_UDMA5, /* udma0-5 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA12_ONLY,
+ .udma_mask = ATA_UDMA5,
.port_ops = &ich_pata_ops,
},
[ich5_sata] =
{
.flags = PIIX_SATA_FLAGS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
@@ -499,8 +499,8 @@ static struct ata_port_info piix_port_info[] = {
[ich6_sata] =
{
.flags = PIIX_SATA_FLAGS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
@@ -508,8 +508,8 @@ static struct ata_port_info piix_port_info[] = {
[ich6m_sata] =
{
.flags = PIIX_SATA_FLAGS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
@@ -517,8 +517,8 @@ static struct ata_port_info piix_port_info[] = {
[ich8_sata] =
{
.flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
@@ -526,8 +526,8 @@ static struct ata_port_info piix_port_info[] = {
[ich8_2port_sata] =
{
.flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
@@ -535,8 +535,8 @@ static struct ata_port_info piix_port_info[] = {
[tolapai_sata] =
{
.flags = PIIX_SATA_FLAGS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
@@ -544,8 +544,8 @@ static struct ata_port_info piix_port_info[] = {
[ich8m_apple_sata] =
{
.flags = PIIX_SATA_FLAGS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
@@ -553,9 +553,9 @@ static struct ata_port_info piix_port_info[] = {
[piix_pata_vmw] =
{
.flags = PIIX_PATA_FLAGS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
- .udma_mask = ATA_UDMA_MASK_40C,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA12_ONLY, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
+ .udma_mask = ATA_UDMA2,
.port_ops = &piix_vmw_ops,
},
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 060bcd6..e7ea77c 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -57,6 +57,7 @@
#include <linux/scatterlist.h>
#include <linux/io.h>
#include <linux/async.h>
+#include <linux/log2.h>
#include <scsi/scsi.h>
#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_host.h>
@@ -2389,6 +2390,7 @@ int ata_dev_configure(struct ata_device *dev)
dev->cylinders = 0;
dev->heads = 0;
dev->sectors = 0;
+ dev->multi_count = 0;
/*
* common ATA, ATAPI feature tests
@@ -2426,8 +2428,15 @@ int ata_dev_configure(struct ata_device *dev)
dev->n_sectors = ata_id_n_sectors(id);
- if (dev->id[59] & 0x100)
- dev->multi_count = dev->id[59] & 0xff;
+ /* get current R/W Multiple count setting */
+ if ((dev->id[47] >> 8) == 0x80 && (dev->id[59] & 0x100)) {
+ unsigned int max = dev->id[47] & 0xff;
+ unsigned int cnt = dev->id[59] & 0xff;
+ /* only recognize/allow powers of two here */
+ if (is_power_of_2(max) && is_power_of_2(cnt))
+ if (cnt <= max)
+ dev->multi_count = cnt;
+ }
if (ata_id_has_lba(id)) {
const char *lba_desc;
@@ -6709,6 +6718,7 @@ EXPORT_SYMBOL_GPL(ata_id_c_string);
EXPORT_SYMBOL_GPL(ata_do_dev_read_id);
EXPORT_SYMBOL_GPL(ata_scsi_simulate);
+EXPORT_SYMBOL_GPL(ata_pio_queue_task);
EXPORT_SYMBOL_GPL(ata_pio_need_iordy);
EXPORT_SYMBOL_GPL(ata_timing_find_mode);
EXPORT_SYMBOL_GPL(ata_timing_compute);
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index ea89091..0183131 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -547,7 +547,7 @@ void ata_scsi_error(struct Scsi_Host *host)
/* For new EH, all qcs are finished in one of three ways -
* normal completion, error completion, and SCSI timeout.
- * Both cmpletions can race against SCSI timeout. When normal
+ * Both completions can race against SCSI timeout. When normal
* completion wins, the qc never reaches EH. When error
* completion wins, the qc has ATA_QCFLAG_FAILED set.
*
@@ -562,7 +562,19 @@ void ata_scsi_error(struct Scsi_Host *host)
int nr_timedout = 0;
spin_lock_irqsave(ap->lock, flags);
-
+
+ /* This must occur under the ap->lock as we don't want
+ a polled recovery to race the real interrupt handler
+
+ The lost_interrupt handler checks for any completed but
+ non-notified command and completes much like an IRQ handler.
+
+ We then fall into the error recovery code which will treat
+ this as if normal completion won the race */
+
+ if (ap->ops->lost_interrupt)
+ ap->ops->lost_interrupt(ap);
+
list_for_each_entry_safe(scmd, tmp, &host->eh_cmd_q, eh_entry) {
struct ata_queued_cmd *qc;
@@ -606,6 +618,9 @@ void ata_scsi_error(struct Scsi_Host *host)
ap->eh_tries = ATA_EH_MAX_TRIES;
} else
spin_unlock_wait(ap->lock);
+
+ /* If we timed raced normal completion and there is nothing to
+ recover nr_timedout == 0 why exactly are we doing error recovery ? */
repeat:
/* invoke error handler */
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index f93dc02..8332e97 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -52,6 +52,7 @@ const struct ata_port_operations ata_sff_port_ops = {
.softreset = ata_sff_softreset,
.hardreset = sata_sff_hardreset,
.postreset = ata_sff_postreset,
+ .drain_fifo = ata_sff_drain_fifo,
.error_handler = ata_sff_error_handler,
.post_internal_cmd = ata_sff_post_internal_cmd,
@@ -64,6 +65,8 @@ const struct ata_port_operations ata_sff_port_ops = {
.sff_irq_on = ata_sff_irq_on,
.sff_irq_clear = ata_sff_irq_clear,
+ .lost_interrupt = ata_sff_lost_interrupt,
+
.port_start = ata_sff_port_start,
};
EXPORT_SYMBOL_GPL(ata_sff_port_ops);
@@ -1646,7 +1649,7 @@ EXPORT_SYMBOL_GPL(ata_sff_qc_fill_rtf);
* RETURNS:
* One if interrupt was handled, zero if not (shared irq).
*/
-inline unsigned int ata_sff_host_intr(struct ata_port *ap,
+unsigned int ata_sff_host_intr(struct ata_port *ap,
struct ata_queued_cmd *qc)
{
struct ata_eh_info *ehi = &ap->link.eh_info;
@@ -1775,6 +1778,48 @@ irqreturn_t ata_sff_interrupt(int irq, void *dev_instance)
EXPORT_SYMBOL_GPL(ata_sff_interrupt);
/**
+ * ata_sff_lost_interrupt - Check for an apparent lost interrupt
+ * @ap: port that appears to have timed out
+ *
+ * Called from the libata error handlers when the core code suspects
+ * an interrupt has been lost. If it has complete anything we can and
+ * then return. Interface must support altstatus for this faster
+ * recovery to occur.
+ *
+ * Locking:
+ * Caller holds host lock
+ */
+
+void ata_sff_lost_interrupt(struct ata_port *ap)
+{
+ u8 status;
+ struct ata_queued_cmd *qc;
+
+ /* Only one outstanding command per SFF channel */
+ qc = ata_qc_from_tag(ap, ap->link.active_tag);
+ /* Check we have a live one.. */
+ if (qc == NULL || !(qc->flags & ATA_QCFLAG_ACTIVE))
+ return;
+ /* We cannot lose an interrupt on a polled command */
+ if (qc->tf.flags & ATA_TFLAG_POLLING)
+ return;
+ /* See if the controller thinks it is still busy - if so the command
+ isn't a lost IRQ but is still in progress */
+ status = ata_sff_altstatus(ap);
+ if (status & ATA_BUSY)
+ return;
+
+ /* There was a command running, we are no longer busy and we have
+ no interrupt. */
+ ata_port_printk(ap, KERN_WARNING, "lost interrupt (Status 0x%x)\n",
+ status);
+ /* Run the host interrupt logic as if the interrupt had not been
+ lost */
+ ata_sff_host_intr(ap, qc);
+}
+EXPORT_SYMBOL_GPL(ata_sff_lost_interrupt);
+
+/**
* ata_sff_freeze - Freeze SFF controller port
* @ap: port to freeze
*
@@ -2199,6 +2244,39 @@ void ata_sff_postreset(struct ata_link *link, unsigned int *classes)
EXPORT_SYMBOL_GPL(ata_sff_postreset);
/**
+ * ata_sff_drain_fifo - Stock FIFO drain logic for SFF controllers
+ * @qc: command
+ *
+ * Drain the FIFO and device of any stuck data following a command
+ * failing to complete. In some cases this is neccessary before a
+ * reset will recover the device.
+ *
+ */
+
+void ata_sff_drain_fifo(struct ata_queued_cmd *qc)
+{
+ int count;
+ struct ata_port *ap;
+
+ /* We only need to flush incoming data when a command was running */
+ if (qc == NULL || qc->dma_dir == DMA_TO_DEVICE)
+ return;
+
+ ap = qc->ap;
+ /* Drain up to 64K of data before we give up this recovery method */
+ for (count = 0; (ap->ops->sff_check_status(ap) & ATA_DRQ)
+ && count < 32768; count++)
+ ioread16(ap->ioaddr.data_addr);
+
+ /* Can become DEBUG later */
+ if (count)
+ ata_port_printk(ap, KERN_DEBUG,
+ "drained %d bytes to clear DRQ.\n", count);
+
+}
+EXPORT_SYMBOL_GPL(ata_sff_drain_fifo);
+
+/**
* ata_sff_error_handler - Stock error handler for BMDMA controller
* @ap: port to handle error for
*
@@ -2239,7 +2317,8 @@ void ata_sff_error_handler(struct ata_port *ap)
* really a timeout event, adjust error mask and
* cancel frozen state.
*/
- if (qc->err_mask == AC_ERR_TIMEOUT && (host_stat & ATA_DMA_ERR)) {
+ if (qc->err_mask == AC_ERR_TIMEOUT
+ && (host_stat & ATA_DMA_ERR)) {
qc->err_mask = AC_ERR_HOST_BUS;
thaw = 1;
}
@@ -2250,6 +2329,13 @@ void ata_sff_error_handler(struct ata_port *ap)
ata_sff_sync(ap); /* FIXME: We don't need this */
ap->ops->sff_check_status(ap);
ap->ops->sff_irq_clear(ap);
+ /* We *MUST* do FIFO draining before we issue a reset as several
+ * devices helpfully clear their internal state and will lock solid
+ * if we touch the data port post reset. Pass qc in case anyone wants
+ * to do different PIO/DMA recovery or has per command fixups
+ */
+ if (ap->ops->drain_fifo)
+ ap->ops->drain_fifo(qc);
spin_unlock_irqrestore(ap->lock, flags);
@@ -2959,4 +3045,3 @@ out:
EXPORT_SYMBOL_GPL(ata_pci_sff_init_one);
#endif /* CONFIG_PCI */
-
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index cea8014..89a1e00 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -79,8 +79,6 @@ extern int ata_build_rw_tf(struct ata_taskfile *tf, struct ata_device *dev,
u64 block, u32 n_block, unsigned int tf_flags,
unsigned int tag);
extern u64 ata_tf_read_block(struct ata_taskfile *tf, struct ata_device *dev);
-extern void ata_pio_queue_task(struct ata_port *ap, void *data,
- unsigned long delay);
extern void ata_port_flush_task(struct ata_port *ap);
extern unsigned ata_exec_internal(struct ata_device *dev,
struct ata_taskfile *tf, const u8 *cdb,
diff --git a/drivers/ata/pata_acpi.c b/drivers/ata/pata_acpi.c
index 8b77a98..d8f35fe 100644
--- a/drivers/ata/pata_acpi.c
+++ b/drivers/ata/pata_acpi.c
@@ -246,9 +246,9 @@ static int pacpi_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA6,
.port_ops = &pacpi_ops,
};
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index eb99dbe..751b7ea 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -492,53 +492,53 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const struct ata_port_info info_early = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
+ .pio_mask = ATA_PIO4,
.port_ops = &ali_early_port_ops
};
/* Revision 0x20 added DMA */
static const struct ata_port_info info_20 = {
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.port_ops = &ali_20_port_ops
};
/* Revision 0x20 with support logic added UDMA */
static const struct ata_port_info info_20_udma = {
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = 0x07, /* UDMA33 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA2,
.port_ops = &ali_20_port_ops
};
/* Revision 0xC2 adds UDMA66 */
static const struct ata_port_info info_c2 = {
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
.port_ops = &ali_c2_port_ops
};
/* Revision 0xC3 is UDMA66 for now */
static const struct ata_port_info info_c3 = {
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
.port_ops = &ali_c2_port_ops
};
/* Revision 0xC4 is UDMA100 */
static const struct ata_port_info info_c4 = {
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &ali_c4_port_ops
};
/* Revision 0xC5 is UDMA133 with LBA48 DMA */
static const struct ata_port_info info_c5 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &ali_c5_port_ops
};
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index 115b1cd..33a74f1 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -455,74 +455,74 @@ static void amd_clear_fifo(struct pci_dev *pdev)
static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const struct ata_port_info info[10] = {
- { /* 0: AMD 7401 */
+ { /* 0: AMD 7401 - no swdma */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07, /* No SWDMA */
- .udma_mask = 0x07, /* UDMA 33 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA2,
.port_ops = &amd33_port_ops
},
{ /* 1: Early AMD7409 - no swdma */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = ATA_UDMA4, /* UDMA 66 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA4,
.port_ops = &amd66_port_ops
},
- { /* 2: AMD 7409, no swdma errata */
+ { /* 2: AMD 7409 */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = ATA_UDMA4, /* UDMA 66 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA4,
.port_ops = &amd66_port_ops
},
{ /* 3: AMD 7411 */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = ATA_UDMA5, /* UDMA 100 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &amd100_port_ops
},
{ /* 4: AMD 7441 */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = ATA_UDMA5, /* UDMA 100 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &amd100_port_ops
},
- { /* 5: AMD 8111*/
+ { /* 5: AMD 8111 - no swdma */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = ATA_UDMA6, /* UDMA 133, no swdma */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA6,
.port_ops = &amd133_port_ops
},
- { /* 6: AMD 8111 UDMA 100 (Serenade) */
+ { /* 6: AMD 8111 UDMA 100 (Serenade) - no swdma */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = ATA_UDMA5, /* UDMA 100, no swdma */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &amd133_port_ops
},
{ /* 7: Nvidia Nforce */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = ATA_UDMA5, /* UDMA 100 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &nv100_port_ops
},
- { /* 8: Nvidia Nforce2 and later */
+ { /* 8: Nvidia Nforce2 and later - no swdma */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = ATA_UDMA6, /* UDMA 133, no swdma */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA6,
.port_ops = &nv133_port_ops
},
{ /* 9: AMD CS5536 (Geode companion) */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = ATA_UDMA5, /* UDMA 100 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &amd100_port_ops
}
};
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
index 6b3092c..d332cfd 100644
--- a/drivers/ata/pata_artop.c
+++ b/drivers/ata/pata_artop.c
@@ -12,7 +12,6 @@
* performance Alessandro Zummo <alessandro.zummo@towertech.it>
*
* TODO
- * 850 serialization once the core supports it
* Investigate no_dsc on 850R
* Clock detect
*/
@@ -29,7 +28,7 @@
#include <linux/ata.h>
#define DRV_NAME "pata_artop"
-#define DRV_VERSION "0.4.4"
+#define DRV_VERSION "0.4.5"
/*
* The ARTOP has 33 Mhz and "over clocked" timing tables. Until we
@@ -283,6 +282,31 @@ static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev)
pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
}
+/**
+ * artop_6210_qc_defer - implement serialization
+ * @qc: command
+ *
+ * Issue commands per host on this chip.
+ */
+
+static int artop6210_qc_defer(struct ata_queued_cmd *qc)
+{
+ struct ata_host *host = qc->ap->host;
+ struct ata_port *alt = host->ports[1 ^ qc->ap->port_no];
+ int rc;
+
+ /* First apply the usual rules */
+ rc = ata_std_qc_defer(qc);
+ if (rc != 0)
+ return rc;
+
+ /* Now apply serialization rules. Only allow a command if the
+ other channel state machine is idle */
+ if (alt && alt->qc_active)
+ return ATA_DEFER_PORT;
+ return 0;
+}
+
static struct scsi_host_template artop_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
@@ -293,6 +317,7 @@ static struct ata_port_operations artop6210_ops = {
.set_piomode = artop6210_set_piomode,
.set_dmamode = artop6210_set_dmamode,
.prereset = artop6210_pre_reset,
+ .qc_defer = artop6210_qc_defer,
};
static struct ata_port_operations artop6260_ops = {
@@ -323,29 +348,29 @@ static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
static int printed_version;
static const struct ata_port_info info_6210 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA2,
.port_ops = &artop6210_ops,
};
static const struct ata_port_info info_626x = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
.port_ops = &artop6260_ops,
};
static const struct ata_port_info info_628x = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &artop6260_ops,
};
static const struct ata_port_info info_628x_fast = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &artop6260_ops,
};
@@ -362,12 +387,8 @@ static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
if (id->driver_data == 0) { /* 6210 variant */
ppi[0] = &info_6210;
- ppi[1] = &ata_dummy_port_info;
/* BIOS may have left us in UDMA, clear it before libata probe */
pci_write_config_byte(pdev, 0x54, 0);
- /* For the moment (also lacks dsc) */
- printk(KERN_WARNING "ARTOP 6210 requires serialize functionality not yet supported by libata.\n");
- printk(KERN_WARNING "Secondary ATA ports will not be activated.\n");
}
else if (id->driver_data == 1) /* 6260 */
ppi[0] = &info_626x;
diff --git a/drivers/ata/pata_at32.c b/drivers/ata/pata_at32.c
index ab61095..5c129f9 100644
--- a/drivers/ata/pata_at32.c
+++ b/drivers/ata/pata_at32.c
@@ -67,7 +67,9 @@
*
* Alter PIO_MASK below according to table to set maximal PIO mode.
*/
-#define PIO_MASK (0x1f)
+enum {
+ PIO_MASK = ATA_PIO4,
+};
/*
* Struct containing private information about device.
diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
index 506adde..bec0b8a 100644
--- a/drivers/ata/pata_atiixp.c
+++ b/drivers/ata/pata_atiixp.c
@@ -220,9 +220,9 @@ static int atiixp_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x06, /* No MWDMA0 support */
- .udma_mask = 0x3F,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA12_ONLY,
+ .udma_mask = ATA_UDMA5,
.port_ops = &atiixp_port_ops
};
static const struct pci_bits atiixp_enable_bits[] = {
diff --git a/drivers/ata/pata_bf54x.c b/drivers/ata/pata_bf54x.c
index 1050fed..c4b47a3 100644
--- a/drivers/ata/pata_bf54x.c
+++ b/drivers/ata/pata_bf54x.c
@@ -1502,7 +1502,7 @@ static struct ata_port_info bfin_port_info[] = {
.flags = ATA_FLAG_SLAVE_POSS
| ATA_FLAG_MMIO
| ATA_FLAG_NO_LEGACY,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.mwdma_mask = 0,
.udma_mask = 0,
.port_ops = &bfin_pata_ops,
diff --git a/drivers/ata/pata_cmd640.c b/drivers/ata/pata_cmd640.c
index 34a3942..5acf9fa 100644
--- a/drivers/ata/pata_cmd640.c
+++ b/drivers/ata/pata_cmd640.c
@@ -211,7 +211,7 @@ static int cmd640_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
+ .pio_mask = ATA_PIO4,
.port_ops = &cmd640_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c
index 3167d8f..f98dffe 100644
--- a/drivers/ata/pata_cmd64x.c
+++ b/drivers/ata/pata_cmd64x.c
@@ -299,40 +299,40 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
static const struct ata_port_info cmd_info[6] = {
{ /* CMD 643 - no UDMA */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.port_ops = &cmd64x_port_ops
},
{ /* CMD 646 with broken UDMA */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.port_ops = &cmd64x_port_ops
},
{ /* CMD 646 with working UDMA */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA2,
.port_ops = &cmd64x_port_ops
},
{ /* CMD 646 rev 1 */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.port_ops = &cmd646r1_port_ops
},
{ /* CMD 648 */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
.port_ops = &cmd648_port_ops
},
{ /* CMD 649 */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &cmd648_port_ops
}
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c
index 1186bcd..db6a969 100644
--- a/drivers/ata/pata_cs5520.c
+++ b/drivers/ata/pata_cs5520.c
@@ -158,7 +158,7 @@ static int __devinit cs5520_init_one(struct pci_dev *pdev, const struct pci_devi
static const unsigned int ctl_port[] = { 0x3F6, 0x376 };
struct ata_port_info pi = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
+ .pio_mask = ATA_PIO4,
.port_ops = &cs5520_port_ops,
};
const struct ata_port_info *ppi[2];
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
index bba4533..c974b05 100644
--- a/drivers/ata/pata_cs5530.c
+++ b/drivers/ata/pata_cs5530.c
@@ -298,15 +298,15 @@ static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA2,
.port_ops = &cs5530_port_ops
};
/* The docking connector doesn't do UDMA, and it seems not MWDMA */
static const struct ata_port_info info_palmax_secondary = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
+ .pio_mask = ATA_PIO4,
.port_ops = &cs5530_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
diff --git a/drivers/ata/pata_cs5535.c b/drivers/ata/pata_cs5535.c
index 8b236af..d33aa28 100644
--- a/drivers/ata/pata_cs5535.c
+++ b/drivers/ata/pata_cs5535.c
@@ -181,8 +181,8 @@ static int cs5535_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
.port_ops = &cs5535_port_ops
};
diff --git a/drivers/ata/pata_cs5536.c b/drivers/ata/pata_cs5536.c
index afed929..6da4cb4 100644
--- a/drivers/ata/pata_cs5536.c
+++ b/drivers/ata/pata_cs5536.c
@@ -241,8 +241,8 @@ static int cs5536_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &cs5536_port_ops,
};
diff --git a/drivers/ata/pata_cypress.c b/drivers/ata/pata_cypress.c
index d546425..8fb040b 100644
--- a/drivers/ata/pata_cypress.c
+++ b/drivers/ata/pata_cypress.c
@@ -124,8 +124,8 @@ static int cy82c693_init_one(struct pci_dev *pdev, const struct pci_device_id *i
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.port_ops = &cy82c693_port_ops
};
const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c
index ac6392e..2085e0a 100644
--- a/drivers/ata/pata_efar.c
+++ b/drivers/ata/pata_efar.c
@@ -251,9 +251,9 @@ static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
static int printed_version;
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma1-2 */
- .udma_mask = 0x0f, /* UDMA 66 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA4,
.port_ops = &efar_ops,
};
const struct ata_port_info *ppi[] = { &info, NULL };
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index 65c28e5..d7f2da1 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -336,8 +336,8 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info_hpt366 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
.port_ops = &hpt366_port_ops
};
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index 4216399..81ab570 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -753,55 +753,55 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
/* HPT370 - UDMA100 */
static const struct ata_port_info info_hpt370 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &hpt370_port_ops
};
/* HPT370A - UDMA100 */
static const struct ata_port_info info_hpt370a = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &hpt370a_port_ops
};
/* HPT370 - UDMA100 */
static const struct ata_port_info info_hpt370_33 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &hpt370_port_ops
};
/* HPT370A - UDMA100 */
static const struct ata_port_info info_hpt370a_33 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &hpt370a_port_ops
};
/* HPT371, 372 and friends - UDMA133 */
static const struct ata_port_info info_hpt372 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &hpt372_port_ops
};
/* HPT374 - UDMA100, function 1 uses different prereset method */
static const struct ata_port_info info_hpt374_fn0 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &hpt372_port_ops
};
static const struct ata_port_info info_hpt374_fn1 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &hpt374_fn1_port_ops
};
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index d5c9fd7..3d59fe0 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -441,8 +441,8 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
/* HPT372N and friends - UDMA133 */
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &hpt3x2n_port_ops
};
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
index f19cc64..7e31025 100644
--- a/drivers/ata/pata_hpt3x3.c
+++ b/drivers/ata/pata_hpt3x3.c
@@ -188,11 +188,11 @@ static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
static int printed_version;
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
+ .pio_mask = ATA_PIO4,
#if defined(CONFIG_PATA_HPT3X3_DMA)
/* Further debug needed */
- .mwdma_mask = 0x07,
- .udma_mask = 0x07,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA2,
#endif
.port_ops = &hpt3x3_port_ops
};
diff --git a/drivers/ata/pata_icside.c b/drivers/ata/pata_icside.c
index cf9e984..e7347db 100644
--- a/drivers/ata/pata_icside.c
+++ b/drivers/ata/pata_icside.c
@@ -297,7 +297,7 @@ static int icside_dma_init(struct pata_icside_info *info)
if (ec->dma != NO_DMA && !request_dma(ec->dma, DRV_NAME)) {
state->dma = ec->dma;
- info->mwdma_mask = 0x07; /* MW0..2 */
+ info->mwdma_mask = ATA_MWDMA2;
}
return 0;
@@ -473,7 +473,7 @@ static int __devinit pata_icside_add_ports(struct pata_icside_info *info)
for (i = 0; i < info->nr_ports; i++) {
struct ata_port *ap = host->ports[i];
- ap->pio_mask = 0x1f;
+ ap->pio_mask = ATA_PIO4;
ap->mwdma_mask = info->mwdma_mask;
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->ops = &pata_icside_port_ops;
diff --git a/drivers/ata/pata_isapnp.c b/drivers/ata/pata_isapnp.c
index 15cdb91..4bceb88 100644
--- a/drivers/ata/pata_isapnp.c
+++ b/drivers/ata/pata_isapnp.c
@@ -17,7 +17,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_isapnp"
-#define DRV_VERSION "0.2.2"
+#define DRV_VERSION "0.2.5"
static struct scsi_host_template isapnp_sht = {
ATA_PIO_SHT(DRV_NAME),
@@ -28,6 +28,13 @@ static struct ata_port_operations isapnp_port_ops = {
.cable_detect = ata_cable_40wire,
};
+static struct ata_port_operations isapnp_noalt_port_ops = {
+ .inherits = &ata_sff_port_ops,
+ .cable_detect = ata_cable_40wire,
+ /* No altstatus so we don't want to use the lost interrupt poll */
+ .lost_interrupt = ATA_OP_NULL,
+};
+
/**
* isapnp_init_one - attach an isapnp interface
* @idev: PnP device
@@ -65,8 +72,8 @@ static int isapnp_init_one(struct pnp_dev *idev, const struct pnp_device_id *dev
ap = host->ports[0];
- ap->ops = &isapnp_port_ops;
- ap->pio_mask = 1;
+ ap->ops = &isapnp_noalt_port_ops;
+ ap->pio_mask = ATA_PIO0;
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->ioaddr.cmd_addr = cmd_addr;
@@ -76,6 +83,7 @@ static int isapnp_init_one(struct pnp_dev *idev, const struct pnp_device_id *dev
pnp_port_start(idev, 1), 1);
ap->ioaddr.altstatus_addr = ctl_addr;
ap->ioaddr.ctl_addr = ctl_addr;
+ ap->ops = &isapnp_port_ops;
}
ata_sff_std_ports(&ap->ioaddr);
diff --git a/drivers/ata/pata_it8213.c b/drivers/ata/pata_it8213.c
index c113d7c..f156da8 100644
--- a/drivers/ata/pata_it8213.c
+++ b/drivers/ata/pata_it8213.c
@@ -262,8 +262,8 @@ static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *en
static int printed_version;
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4, /* FIXME: want UDMA 100? */
.port_ops = &it8213_ops,
};
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
index b05b86a..188bc2f 100644
--- a/drivers/ata/pata_it821x.c
+++ b/drivers/ata/pata_it821x.c
@@ -875,29 +875,29 @@ static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
static const struct ata_port_info info_smart = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &it821x_smart_port_ops
};
static const struct ata_port_info info_passthru = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &it821x_passthru_port_ops
};
static const struct ata_port_info info_rdc = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &it821x_rdc_port_ops
};
static const struct ata_port_info info_rdc_11 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
/* No UDMA */
.port_ops = &it821x_rdc_port_ops
};
diff --git a/drivers/ata/pata_ixp4xx_cf.c b/drivers/ata/pata_ixp4xx_cf.c
index b173c15..19fdecf 100644
--- a/drivers/ata/pata_ixp4xx_cf.c
+++ b/drivers/ata/pata_ixp4xx_cf.c
@@ -176,7 +176,7 @@ static __devinit int ixp4xx_pata_probe(struct platform_device *pdev)
ap = host->ports[0];
ap->ops = &ixp4xx_port_ops;
- ap->pio_mask = 0x1f; /* PIO4 */
+ ap->pio_mask = ATA_PIO4;
ap->flags |= ATA_FLAG_MMIO | ATA_FLAG_NO_LEGACY | ATA_FLAG_NO_ATAPI;
ixp4xx_setup_port(ap, data, cs0->start, cs1->start);
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
index 38cf1ab..3a1474a 100644
--- a/drivers/ata/pata_jmicron.c
+++ b/drivers/ata/pata_jmicron.c
@@ -136,8 +136,8 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &jmicron_ops,
diff --git a/drivers/ata/pata_legacy.c b/drivers/ata/pata_legacy.c
index e3bc1b4..3f830f0 100644
--- a/drivers/ata/pata_legacy.c
+++ b/drivers/ata/pata_legacy.c
@@ -129,7 +129,7 @@ static int qdi; /* Set to probe QDI controllers */
static int winbond; /* Set to probe Winbond controllers,
give I/O port if non standard */
static int autospeed; /* Chip present which snoops speed changes */
-static int pio_mask = 0x1F; /* PIO range for autospeed devices */
+static int pio_mask = ATA_PIO4; /* PIO range for autospeed devices */
static int iordy_mask = 0xFFFFFFFF; /* Use iordy if available */
/**
diff --git a/drivers/ata/pata_marvell.c b/drivers/ata/pata_marvell.c
index 76e399b..2096fb7 100644
--- a/drivers/ata/pata_marvell.c
+++ b/drivers/ata/pata_marvell.c
@@ -126,8 +126,8 @@ static int marvell_init_one (struct pci_dev *pdev, const struct pci_device_id *i
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &marvell_ops,
@@ -136,8 +136,8 @@ static int marvell_init_one (struct pci_dev *pdev, const struct pci_device_id *i
/* Slave possible as its magically mapped not real */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &marvell_ops,
diff --git a/drivers/ata/pata_mpc52xx.c b/drivers/ata/pata_mpc52xx.c
index 50ae6d1..68d27bc 100644
--- a/drivers/ata/pata_mpc52xx.c
+++ b/drivers/ata/pata_mpc52xx.c
@@ -737,10 +737,10 @@ mpc52xx_ata_probe(struct of_device *op, const struct of_device_id *match)
*/
prop = of_get_property(op->node, "mwdma-mode", &proplen);
if ((prop) && (proplen >= 4))
- mwdma_mask = 0x7 & ((1 << (*prop + 1)) - 1);
+ mwdma_mask = ATA_MWDMA2 & ((1 << (*prop + 1)) - 1);
prop = of_get_property(op->node, "udma-mode", &proplen);
if ((prop) && (proplen >= 4))
- udma_mask = 0x7 & ((1 << (*prop + 1)) - 1);
+ udma_mask = ATA_UDMA2 & ((1 << (*prop + 1)) - 1);
ata_irq = irq_of_parse_and_map(op->node, 0);
if (ata_irq == NO_IRQ) {
diff --git a/drivers/ata/pata_mpiix.c b/drivers/ata/pata_mpiix.c
index aa576ca..b21f002 100644
--- a/drivers/ata/pata_mpiix.c
+++ b/drivers/ata/pata_mpiix.c
@@ -200,7 +200,7 @@ static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id)
the MPIIX your box goes castors up */
ap->ops = &mpiix_port_ops;
- ap->pio_mask = 0x1F;
+ ap->pio_mask = ATA_PIO4;
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->ioaddr.cmd_addr = cmd_addr;
diff --git a/drivers/ata/pata_netcell.c b/drivers/ata/pata_netcell.c
index 9dc05e1..bdb2369 100644
--- a/drivers/ata/pata_netcell.c
+++ b/drivers/ata/pata_netcell.c
@@ -51,8 +51,8 @@ static int netcell_init_one (struct pci_dev *pdev, const struct pci_device_id *e
.flags = ATA_FLAG_SLAVE_POSS,
/* Actually we don't really care about these as the
firmware deals with it */
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5, /* UDMA 133 */
.port_ops = &netcell_ops,
};
diff --git a/drivers/ata/pata_ninja32.c b/drivers/ata/pata_ninja32.c
index 4dd9a3b..0fb6b1b 100644
--- a/drivers/ata/pata_ninja32.c
+++ b/drivers/ata/pata_ninja32.c
@@ -136,7 +136,7 @@ static int ninja32_init_one(struct pci_dev *dev, const struct pci_device_id *id)
if (!base)
return -ENOMEM;
ap->ops = &ninja32_port_ops;
- ap->pio_mask = 0x1F;
+ ap->pio_mask = ATA_PIO4;
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->ioaddr.cmd_addr = base + 0x10;
diff --git a/drivers/ata/pata_ns87410.c b/drivers/ata/pata_ns87410.c
index 40d411c..ca53fac 100644
--- a/drivers/ata/pata_ns87410.c
+++ b/drivers/ata/pata_ns87410.c
@@ -144,7 +144,7 @@ static int ns87410_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x0F,
+ .pio_mask = ATA_PIO3,
.port_ops = &ns87410_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
diff --git a/drivers/ata/pata_ns87415.c b/drivers/ata/pata_ns87415.c
index 89bf5f8..773b159 100644
--- a/drivers/ata/pata_ns87415.c
+++ b/drivers/ata/pata_ns87415.c
@@ -346,8 +346,8 @@ static int ns87415_init_one (struct pci_dev *pdev, const struct pci_device_id *e
static int printed_version;
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.port_ops = &ns87415_pata_ops,
};
const struct ata_port_info *ppi[] = { &info, NULL };
@@ -355,8 +355,8 @@ static int ns87415_init_one (struct pci_dev *pdev, const struct pci_device_id *e
#if defined(CONFIG_SUPERIO)
static const struct ata_port_info info87560 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.port_ops = &ns87560_pata_ops,
};
diff --git a/drivers/ata/pata_octeon_cf.c b/drivers/ata/pata_octeon_cf.c
index 0fe4ef3..efe2c19 100644
--- a/drivers/ata/pata_octeon_cf.c
+++ b/drivers/ata/pata_octeon_cf.c
@@ -871,7 +871,7 @@ static int __devinit octeon_cf_probe(struct platform_device *pdev)
ap->private_data = cf_port;
cf_port->ap = ap;
ap->ops = &octeon_cf_ops;
- ap->pio_mask = 0x7f; /* Support PIO 0-6 */
+ ap->pio_mask = ATA_PIO6;
ap->flags |= ATA_FLAG_MMIO | ATA_FLAG_NO_LEGACY
| ATA_FLAG_NO_ATAPI | ATA_FLAG_PIO_POLLING;
@@ -900,7 +900,7 @@ static int __devinit octeon_cf_probe(struct platform_device *pdev)
ap->ioaddr.ctl_addr = cs1 + (6 << 1) + 1;
octeon_cf_ops.sff_data_xfer = octeon_cf_data_xfer16;
- ap->mwdma_mask = 0x1f; /* Support MWDMA 0-4 */
+ ap->mwdma_mask = ATA_MWDMA4;
irq = platform_get_irq(pdev, 0);
irq_handler = octeon_cf_interrupt;
diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c
index 2c1a91c..84ac503 100644
--- a/drivers/ata/pata_oldpiix.c
+++ b/drivers/ata/pata_oldpiix.c
@@ -238,8 +238,8 @@ static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *e
static int printed_version;
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma1-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.port_ops = &oldpiix_pata_ops,
};
const struct ata_port_info *ppi[] = { &info, NULL };
diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c
index e4fa4d5..99eddda 100644
--- a/drivers/ata/pata_opti.c
+++ b/drivers/ata/pata_opti.c
@@ -163,7 +163,7 @@ static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
+ .pio_mask = ATA_PIO4,
.port_ops = &opti_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
diff --git a/drivers/ata/pata_optidma.c b/drivers/ata/pata_optidma.c
index 93bb6e9..86885a4 100644
--- a/drivers/ata/pata_optidma.c
+++ b/drivers/ata/pata_optidma.c
@@ -399,15 +399,15 @@ static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info_82c700 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.port_ops = &optidma_port_ops
};
static const struct ata_port_info info_82c700_udma = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA2,
.port_ops = &optiplus_port_ops
};
const struct ata_port_info *ppi[] = { &info_82c700, NULL };
diff --git a/drivers/ata/pata_pcmcia.c b/drivers/ata/pata_pcmcia.c
index 64b2e22..f4d009e 100644
--- a/drivers/ata/pata_pcmcia.c
+++ b/drivers/ata/pata_pcmcia.c
@@ -42,7 +42,7 @@
#define DRV_NAME "pata_pcmcia"
-#define DRV_VERSION "0.3.3"
+#define DRV_VERSION "0.3.5"
/*
* Private data structure to glue stuff together
@@ -126,6 +126,37 @@ static unsigned int ata_data_xfer_8bit(struct ata_device *dev,
return buflen;
}
+/**
+ * pcmcia_8bit_drain_fifo - Stock FIFO drain logic for SFF controllers
+ * @qc: command
+ *
+ * Drain the FIFO and device of any stuck data following a command
+ * failing to complete. In some cases this is neccessary before a
+ * reset will recover the device.
+ *
+ */
+
+void pcmcia_8bit_drain_fifo(struct ata_queued_cmd *qc)
+{
+ int count;
+ struct ata_port *ap;
+
+ /* We only need to flush incoming data when a command was running */
+ if (qc == NULL || qc->dma_dir == DMA_TO_DEVICE)
+ return;
+
+ ap = qc->ap;
+
+ /* Drain up to 64K of data before we give up this recovery method */
+ for (count = 0; (ap->ops->sff_check_status(ap) & ATA_DRQ)
+ && count++ < 65536;)
+ ioread8(ap->ioaddr.data_addr);
+
+ if (count)
+ ata_port_printk(ap, KERN_WARNING, "drained %d bytes to clear DRQ.\n",
+ count);
+
+}
static struct scsi_host_template pcmcia_sht = {
ATA_PIO_SHT(DRV_NAME),
@@ -143,6 +174,7 @@ static struct ata_port_operations pcmcia_8bit_port_ops = {
.sff_data_xfer = ata_data_xfer_8bit,
.cable_detect = ata_cable_40wire,
.set_mode = pcmcia_set_mode_8bit,
+ .drain_fifo = pcmcia_8bit_drain_fifo,
};
#define CS_CHECK(fn, ret) \
@@ -299,7 +331,7 @@ static int pcmcia_init_one(struct pcmcia_device *pdev)
ap = host->ports[p];
ap->ops = ops;
- ap->pio_mask = 1; /* ISA so PIO 0 cycles */
+ ap->pio_mask = ATA_PIO0; /* ISA so PIO 0 cycles */
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->ioaddr.cmd_addr = io_addr + 0x10 * p;
ap->ioaddr.altstatus_addr = ctl_addr + 0x10 * p;
diff --git a/drivers/ata/pata_pdc2027x.c b/drivers/ata/pata_pdc2027x.c
index e94efcc..ca5cad0 100644
--- a/drivers/ata/pata_pdc2027x.c
+++ b/drivers/ata/pata_pdc2027x.c
@@ -152,18 +152,18 @@ static struct ata_port_info pdc2027x_port_info[] = {
{
.flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS |
ATA_FLAG_MMIO,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = ATA_UDMA5, /* udma0-5 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &pdc2027x_pata100_ops,
},
/* PDC_UDMA_133 */
{
.flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS |
ATA_FLAG_MMIO,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = ATA_UDMA6, /* udma0-6 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA6,
.port_ops = &pdc2027x_pata133_ops,
},
};
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c
index 799a6a0..5fedb3d 100644
--- a/drivers/ata/pata_pdc202xx_old.c
+++ b/drivers/ata/pata_pdc202xx_old.c
@@ -291,22 +291,22 @@ static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id
static const struct ata_port_info info[3] = {
{
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA2,
.port_ops = &pdc2024x_port_ops
},
{
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
.port_ops = &pdc2026x_port_ops
},
{
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &pdc2026x_port_ops
}
diff --git a/drivers/ata/pata_qdi.c b/drivers/ata/pata_qdi.c
index f1b26f7..45879dc 100644
--- a/drivers/ata/pata_qdi.c
+++ b/drivers/ata/pata_qdi.c
@@ -212,11 +212,11 @@ static __init int qdi_init_one(unsigned long port, int type, unsigned long io, i
if (type == 6580) {
ap->ops = &qdi6580_port_ops;
- ap->pio_mask = 0x1F;
+ ap->pio_mask = ATA_PIO4;
ap->flags |= ATA_FLAG_SLAVE_POSS;
} else {
ap->ops = &qdi6500_port_ops;
- ap->pio_mask = 0x07; /* Actually PIO3 !IORDY is possible */
+ ap->pio_mask = ATA_PIO2; /* Actually PIO3 !IORDY is possible */
ap->flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_NO_IORDY;
}
diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c
index 695d44a..4401b33 100644
--- a/drivers/ata/pata_radisys.c
+++ b/drivers/ata/pata_radisys.c
@@ -216,9 +216,9 @@ static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *e
static int printed_version;
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma1-2 */
- .udma_mask = 0x14, /* UDMA33/66 only */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA12_ONLY,
+ .udma_mask = ATA_UDMA24_ONLY,
.port_ops = &radisys_pata_ops,
};
const struct ata_port_info *ppi[] = { &info, NULL };
diff --git a/drivers/ata/pata_rb532_cf.c b/drivers/ata/pata_rb532_cf.c
index ebfcda2..8e3cdef 100644
--- a/drivers/ata/pata_rb532_cf.c
+++ b/drivers/ata/pata_rb532_cf.c
@@ -48,63 +48,11 @@
struct rb532_cf_info {
void __iomem *iobase;
unsigned int gpio_line;
- int frozen;
unsigned int irq;
};
/* ------------------------------------------------------------------------ */
-static inline void rb532_pata_finish_io(struct ata_port *ap)
-{
- struct ata_host *ah = ap->host;
- struct rb532_cf_info *info = ah->private_data;
-
- /* FIXME: Keep previous delay. If this is merely a fence then
- ata_sff_sync might be sufficient. */
- ata_sff_dma_pause(ap);
- ndelay(RB500_CF_IO_DELAY);
-}
-
-static void rb532_pata_exec_command(struct ata_port *ap,
- const struct ata_taskfile *tf)
-{
- writeb(tf->command, ap->ioaddr.command_addr);
- rb532_pata_finish_io(ap);
-}
-
-static unsigned int rb532_pata_data_xfer(struct ata_device *adev, unsigned char *buf,
- unsigned int buflen, int write_data)
-{
- struct ata_port *ap = adev->link->ap;
- void __iomem *ioaddr = ap->ioaddr.data_addr;
- int retlen = buflen;
-
- if (write_data) {
- for (; buflen > 0; buflen--, buf++)
- writeb(*buf, ioaddr);
- } else {
- for (; buflen > 0; buflen--, buf++)
- *buf = readb(ioaddr);
- }
-
- rb532_pata_finish_io(adev->link->ap);
- return retlen;
-}
-
-static void rb532_pata_freeze(struct ata_port *ap)
-{
- struct rb532_cf_info *info = ap->host->private_data;
-
- info->frozen = 1;
-}
-
-static void rb532_pata_thaw(struct ata_port *ap)
-{
- struct rb532_cf_info *info = ap->host->private_data;
-
- info->frozen = 0;
-}
-
static irqreturn_t rb532_pata_irq_handler(int irq, void *dev_instance)
{
struct ata_host *ah = dev_instance;
@@ -112,8 +60,7 @@ static irqreturn_t rb532_pata_irq_handler(int irq, void *dev_instance)
if (gpio_get_value(info->gpio_line)) {
set_irq_type(info->irq, IRQ_TYPE_LEVEL_LOW);
- if (!info->frozen)
- ata_sff_interrupt(info->irq, dev_instance);
+ ata_sff_interrupt(info->irq, dev_instance);
} else {
set_irq_type(info->irq, IRQ_TYPE_LEVEL_HIGH);
}
@@ -123,10 +70,7 @@ static irqreturn_t rb532_pata_irq_handler(int irq, void *dev_instance)
static struct ata_port_operations rb532_pata_port_ops = {
.inherits = &ata_sff_port_ops,
- .sff_exec_command = rb532_pata_exec_command,
- .sff_data_xfer = rb532_pata_data_xfer,
- .freeze = rb532_pata_freeze,
- .thaw = rb532_pata_thaw,
+ .sff_data_xfer = ata_sff_data_xfer32,
};
/* ------------------------------------------------------------------------ */
@@ -145,7 +89,7 @@ static void rb532_pata_setup_ports(struct ata_host *ah)
ap = ah->ports[0];
ap->ops = &rb532_pata_port_ops;
- ap->pio_mask = 0x1f; /* PIO4 */
+ ap->pio_mask = ATA_PIO4;
ap->flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO;
ap->ioaddr.cmd_addr = info->iobase + RB500_CF_REG_BASE;
@@ -160,7 +104,7 @@ static void rb532_pata_setup_ports(struct ata_host *ah)
static __devinit int rb532_pata_driver_probe(struct platform_device *pdev)
{
- unsigned int irq;
+ int irq;
int gpio;
struct resource *res;
struct ata_host *ah;
diff --git a/drivers/ata/pata_rz1000.c b/drivers/ata/pata_rz1000.c
index 46d6bc1..0c574c0 100644
--- a/drivers/ata/pata_rz1000.c
+++ b/drivers/ata/pata_rz1000.c
@@ -88,7 +88,7 @@ static int rz1000_init_one (struct pci_dev *pdev, const struct pci_device_id *en
static int printed_version;
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
+ .pio_mask = ATA_PIO4,
.port_ops = &rz1000_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c
index 9a4bdca..f49814d 100644
--- a/drivers/ata/pata_sc1200.c
+++ b/drivers/ata/pata_sc1200.c
@@ -2,7 +2,6 @@
* New ATA layer SC1200 driver Alan Cox <alan@lxorguk.ukuu.org.uk>
*
* TODO: Mode selection filtering
- * TODO: Can't enable second channel until ATA core has serialize
* TODO: Needs custom DMA cleanup code
*
* Based very heavily on
@@ -178,6 +177,31 @@ static unsigned int sc1200_qc_issue(struct ata_queued_cmd *qc)
return ata_sff_qc_issue(qc);
}
+/**
+ * sc1200_qc_defer - implement serialization
+ * @qc: command
+ *
+ * Serialize command issue on this controller.
+ */
+
+static int sc1200_qc_defer(struct ata_queued_cmd *qc)
+{
+ struct ata_host *host = qc->ap->host;
+ struct ata_port *alt = host->ports[1 ^ qc->ap->port_no];
+ int rc;
+
+ /* First apply the usual rules */
+ rc = ata_std_qc_defer(qc);
+ if (rc != 0)
+ return rc;
+
+ /* Now apply serialization rules. Only allow a command if the
+ other channel state machine is idle */
+ if (alt && alt->qc_active)
+ return ATA_DEFER_PORT;
+ return 0;
+}
+
static struct scsi_host_template sc1200_sht = {
ATA_BMDMA_SHT(DRV_NAME),
.sg_tablesize = LIBATA_DUMB_MAX_PRD,
@@ -187,6 +211,7 @@ static struct ata_port_operations sc1200_port_ops = {
.inherits = &ata_bmdma_port_ops,
.qc_prep = ata_sff_dumb_qc_prep,
.qc_issue = sc1200_qc_issue,
+ .qc_defer = sc1200_qc_defer,
.cable_detect = ata_cable_40wire,
.set_piomode = sc1200_set_piomode,
.set_dmamode = sc1200_set_dmamode,
@@ -205,13 +230,13 @@ static int sc1200_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA2,
.port_ops = &sc1200_port_ops
};
/* Can't enable port 2 yet, see top comments */
- const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
+ const struct ata_port_info *ppi[] = { &info, };
return ata_pci_sff_init_one(dev, ppi, &sc1200_sht, NULL);
}
diff --git a/drivers/ata/pata_scc.c b/drivers/ata/pata_scc.c
index d447f1c..4257d6b 100644
--- a/drivers/ata/pata_scc.c
+++ b/drivers/ata/pata_scc.c
@@ -1001,8 +1001,8 @@ static struct ata_port_operations scc_pata_ops = {
static struct ata_port_info scc_port_info[] = {
{
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_MMIO | ATA_FLAG_NO_LEGACY,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x00,
+ .pio_mask = ATA_PIO4,
+ /* No MWDMA */
.udma_mask = ATA_UDMA6,
.port_ops = &scc_pata_ops,
},
diff --git a/drivers/ata/pata_sch.c b/drivers/ata/pata_sch.c
index 6aeeeeb..99cceb4 100644
--- a/drivers/ata/pata_sch.c
+++ b/drivers/ata/pata_sch.c
@@ -84,9 +84,9 @@ static struct ata_port_operations sch_pata_ops = {
static struct ata_port_info sch_port_info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = ATA_PIO4, /* pio0-4 */
- .mwdma_mask = ATA_MWDMA2, /* mwdma0-2 */
- .udma_mask = ATA_UDMA5, /* udma0-5 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &sch_pata_ops,
};
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c
index 8d2fd9d..beaed12 100644
--- a/drivers/ata/pata_serverworks.c
+++ b/drivers/ata/pata_serverworks.c
@@ -398,26 +398,26 @@ static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id
static const struct ata_port_info info[4] = {
{ /* OSB4 */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA2,
.port_ops = &serverworks_osb4_port_ops
}, { /* OSB4 no UDMA */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = 0x00,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ /* No UDMA */
.port_ops = &serverworks_osb4_port_ops
}, { /* CSB5 */
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
.port_ops = &serverworks_csb_port_ops
}, { /* CSB5 - later revisions*/
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &serverworks_csb_port_ops
}
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index 9e764e5..4cb649d 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -282,15 +282,15 @@ static int __devinit sil680_init_one(struct pci_dev *pdev,
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &sil680_port_ops
};
static const struct ata_port_info info_slow = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &sil680_port_ops
};
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index 27ceb42..488e77b 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -552,51 +552,57 @@ static struct ata_port_operations sis_old_ops = {
static const struct ata_port_info sis_info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07,
- .udma_mask = 0,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ /* No UDMA */
.port_ops = &sis_old_ops,
};
static const struct ata_port_info sis_info33 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07,
- .udma_mask = ATA_UDMA2, /* UDMA 33 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA2,
.port_ops = &sis_old_ops,
};
static const struct ata_port_info sis_info66 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = ATA_UDMA4, /* UDMA 66 */
+ .pio_mask = ATA_PIO4,
+ /* No MWDMA */
+ .udma_mask = ATA_UDMA4,
.port_ops = &sis_66_ops,
};
static const struct ata_port_info sis_info100 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
+ /* No MWDMA */
.udma_mask = ATA_UDMA5,
.port_ops = &sis_100_ops,
};
static const struct ata_port_info sis_info100_early = {
.flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ /* No MWDMA */
.udma_mask = ATA_UDMA5,
- .pio_mask = 0x1f, /* pio0-4 */
.port_ops = &sis_66_ops,
};
static const struct ata_port_info sis_info133 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
+ /* No MWDMA */
.udma_mask = ATA_UDMA6,
.port_ops = &sis_133_ops,
};
const struct ata_port_info sis_info133_for_sata = {
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
+ /* No MWDMA */
.udma_mask = ATA_UDMA6,
.port_ops = &sis_133_for_sata_ops,
};
static const struct ata_port_info sis_info133_early = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
+ /* No MWDMA */
.udma_mask = ATA_UDMA6,
.port_ops = &sis_133_early_ops,
};
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index 1b0e7b6..29f733c 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -283,13 +283,13 @@ static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id
{
static const struct ata_port_info info_dma = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.port_ops = &sl82c105_port_ops
};
static const struct ata_port_info info_early = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
+ .pio_mask = ATA_PIO4,
.port_ops = &sl82c105_port_ops
};
/* for now use only the first port */
diff --git a/drivers/ata/pata_triflex.c b/drivers/ata/pata_triflex.c
index ef95975..f1f13ff 100644
--- a/drivers/ata/pata_triflex.c
+++ b/drivers/ata/pata_triflex.c
@@ -191,8 +191,8 @@ static int triflex_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.port_ops = &triflex_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index ba556d3..b08e6e0 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -422,46 +422,46 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
/* Early VIA without UDMA support */
static const struct ata_port_info via_mwdma_info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.port_ops = &via_port_ops
};
/* Ditto with IRQ masking required */
static const struct ata_port_info via_mwdma_info_borked = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.port_ops = &via_port_ops_noirq,
};
/* VIA UDMA 33 devices (and borked 66) */
static const struct ata_port_info via_udma33_info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA2,
.port_ops = &via_port_ops
};
/* VIA UDMA 66 devices */
static const struct ata_port_info via_udma66_info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
.port_ops = &via_port_ops
};
/* VIA UDMA 100 devices */
static const struct ata_port_info via_udma100_info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &via_port_ops
};
/* UDMA133 with bad AST (All current 133) */
static const struct ata_port_info via_udma133_info = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6, /* FIXME: should check north bridge */
.port_ops = &via_port_ops
};
diff --git a/drivers/ata/pata_winbond.c b/drivers/ata/pata_winbond.c
index 319e164..6d8619b 100644
--- a/drivers/ata/pata_winbond.c
+++ b/drivers/ata/pata_winbond.c
@@ -193,7 +193,7 @@ static __init int winbond_init_one(unsigned long port)
ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx", cmd_port, ctl_port);
ap->ops = &winbond_port_ops;
- ap->pio_mask = 0x1F;
+ ap->pio_mask = ATA_PIO4;
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->ioaddr.cmd_addr = cmd_addr;
ap->ioaddr.altstatus_addr = ctl_addr;
diff --git a/drivers/ata/pdc_adma.c b/drivers/ata/pdc_adma.c
index be53545..3958817 100644
--- a/drivers/ata/pdc_adma.c
+++ b/drivers/ata/pdc_adma.c
@@ -148,6 +148,8 @@ static struct scsi_host_template adma_ata_sht = {
static struct ata_port_operations adma_ata_ops = {
.inherits = &ata_sff_port_ops,
+ .lost_interrupt = ATA_OP_NULL,
+
.check_atapi_dma = adma_check_atapi_dma,
.qc_prep = adma_qc_prep,
.qc_issue = adma_qc_issue,
@@ -166,7 +168,7 @@ static struct ata_port_info adma_port_info[] = {
.flags = ATA_FLAG_SLAVE_POSS |
ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO |
ATA_FLAG_PIO_POLLING,
- .pio_mask = 0x10, /* pio4 */
+ .pio_mask = ATA_PIO4_ONLY,
.udma_mask = ATA_UDMA4,
.port_ops = &adma_ata_ops,
},
diff --git a/drivers/ata/sata_fsl.c b/drivers/ata/sata_fsl.c
index 55bc88c..c2e90e1 100644
--- a/drivers/ata/sata_fsl.c
+++ b/drivers/ata/sata_fsl.c
@@ -1279,8 +1279,8 @@ static struct ata_port_operations sata_fsl_ops = {
static const struct ata_port_info sata_fsl_port_info[] = {
{
.flags = SATA_FSL_HOST_FLAGS,
- .pio_mask = 0x1f, /* pio 0-4 */
- .udma_mask = 0x7f, /* udma 0-6 */
+ .pio_mask = ATA_PIO4,
+ .udma_mask = ATA_UDMA6,
.port_ops = &sata_fsl_ops,
},
};
diff --git a/drivers/ata/sata_inic162x.c b/drivers/ata/sata_inic162x.c
index fbbd87c..305a4f8 100644
--- a/drivers/ata/sata_inic162x.c
+++ b/drivers/ata/sata_inic162x.c
@@ -744,8 +744,8 @@ static struct ata_port_operations inic_port_ops = {
static struct ata_port_info inic_port_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_PIO_DMA,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &inic_port_ops
};
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 74b1080..a377226 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -1,10 +1,13 @@
/*
* sata_mv.c - Marvell SATA support
*
- * Copyright 2008: Marvell Corporation, all rights reserved.
+ * Copyright 2008-2009: Marvell Corporation, all rights reserved.
* Copyright 2005: EMC Corporation, all rights reserved.
* Copyright 2005 Red Hat, Inc. All rights reserved.
*
+ * Originally written by Brett Russ.
+ * Extensive overhaul and enhancement by Mark Lord <mlord@pobox.com>.
+ *
* Please ALWAYS copy linux-ide@vger.kernel.org on emails.
*
* This program is free software; you can redistribute it and/or modify
@@ -25,20 +28,13 @@
/*
* sata_mv TODO list:
*
- * --> Errata workaround for NCQ device errors.
- *
* --> More errata workarounds for PCI-X.
*
* --> Complete a full errata audit for all chipsets to identify others.
*
- * --> ATAPI support (Marvell claims the 60xx/70xx chips can do it).
- *
* --> Develop a low-power-consumption strategy, and implement it.
*
- * --> [Experiment, low priority] Investigate interrupt coalescing.
- * Quite often, especially with PCI Message Signalled Interrupts (MSI),
- * the overhead reduced by interrupt mitigation is quite often not
- * worth the latency cost.
+ * --> Add sysfs attributes for per-chip / per-HC IRQ coalescing thresholds.
*
* --> [Experiment, Marvell value added] Is it possible to use target
* mode to cross-connect two Linux boxes with Marvell cards? If so,
@@ -68,7 +64,27 @@
#include <linux/libata.h>
#define DRV_NAME "sata_mv"
-#define DRV_VERSION "1.25"
+#define DRV_VERSION "1.27"
+
+/*
+ * module options
+ */
+
+static int msi;
+#ifdef CONFIG_PCI
+module_param(msi, int, S_IRUGO);
+MODULE_PARM_DESC(msi, "Enable use of PCI MSI (0=off, 1=on)");
+#endif
+
+static int irq_coalescing_io_count;
+module_param(irq_coalescing_io_count, int, S_IRUGO);
+MODULE_PARM_DESC(irq_coalescing_io_count,
+ "IRQ coalescing I/O count threshold (0..255)");
+
+static int irq_coalescing_usecs;
+module_param(irq_coalescing_usecs, int, S_IRUGO);
+MODULE_PARM_DESC(irq_coalescing_usecs,
+ "IRQ coalescing time threshold in usecs");
enum {
/* BAR's are enumerated in terms of pci_resource_start() terms */
@@ -79,13 +95,32 @@ enum {
MV_MAJOR_REG_AREA_SZ = 0x10000, /* 64KB */
MV_MINOR_REG_AREA_SZ = 0x2000, /* 8KB */
+ /* For use with both IRQ coalescing methods ("all ports" or "per-HC" */
+ COAL_CLOCKS_PER_USEC = 150, /* for calculating COAL_TIMEs */
+ MAX_COAL_TIME_THRESHOLD = ((1 << 24) - 1), /* internal clocks count */
+ MAX_COAL_IO_COUNT = 255, /* completed I/O count */
+
MV_PCI_REG_BASE = 0,
- MV_IRQ_COAL_REG_BASE = 0x18000, /* 6xxx part only */
- MV_IRQ_COAL_CAUSE = (MV_IRQ_COAL_REG_BASE + 0x08),
- MV_IRQ_COAL_CAUSE_LO = (MV_IRQ_COAL_REG_BASE + 0x88),
- MV_IRQ_COAL_CAUSE_HI = (MV_IRQ_COAL_REG_BASE + 0x8c),
- MV_IRQ_COAL_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xcc),
- MV_IRQ_COAL_TIME_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xd0),
+
+ /*
+ * Per-chip ("all ports") interrupt coalescing feature.
+ * This is only for GEN_II / GEN_IIE hardware.
+ *
+ * Coalescing defers the interrupt until either the IO_THRESHOLD
+ * (count of completed I/Os) is met, or the TIME_THRESHOLD is met.
+ */
+ MV_COAL_REG_BASE = 0x18000,
+ MV_IRQ_COAL_CAUSE = (MV_COAL_REG_BASE + 0x08),
+ ALL_PORTS_COAL_IRQ = (1 << 4), /* all ports irq event */
+
+ MV_IRQ_COAL_IO_THRESHOLD = (MV_COAL_REG_BASE + 0xcc),
+ MV_IRQ_COAL_TIME_THRESHOLD = (MV_COAL_REG_BASE + 0xd0),
+
+ /*
+ * Registers for the (unused here) transaction coalescing feature:
+ */
+ MV_TRAN_COAL_CAUSE_LO = (MV_COAL_REG_BASE + 0x88),
+ MV_TRAN_COAL_CAUSE_HI = (MV_COAL_REG_BASE + 0x8c),
MV_SATAHC0_REG_BASE = 0x20000,
MV_FLASH_CTL_OFS = 0x1046c,
@@ -117,17 +152,16 @@ enum {
/* Host Flags */
MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */
- MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */
MV_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI |
- ATA_FLAG_PIO_POLLING,
+ ATA_FLAG_MMIO | ATA_FLAG_PIO_POLLING,
+
+ MV_GEN_I_FLAGS = MV_COMMON_FLAGS | ATA_FLAG_NO_ATAPI,
- MV_6XXX_FLAGS = MV_FLAG_IRQ_COALESCE,
+ MV_GEN_II_FLAGS = MV_COMMON_FLAGS | ATA_FLAG_NCQ |
+ ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA,
- MV_GENIIE_FLAGS = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ | ATA_FLAG_AN,
+ MV_GEN_IIE_FLAGS = MV_GEN_II_FLAGS | ATA_FLAG_AN,
CRQB_FLAG_READ = (1 << 0),
CRQB_TAG_SHIFT = 1,
@@ -180,16 +214,18 @@ enum {
PCI_HC_MAIN_IRQ_MASK_OFS = 0x1d64,
SOC_HC_MAIN_IRQ_CAUSE_OFS = 0x20020,
SOC_HC_MAIN_IRQ_MASK_OFS = 0x20024,
- ERR_IRQ = (1 << 0), /* shift by port # */
- DONE_IRQ = (1 << 1), /* shift by port # */
+ ERR_IRQ = (1 << 0), /* shift by (2 * port #) */
+ DONE_IRQ = (1 << 1), /* shift by (2 * port #) */
HC0_IRQ_PEND = 0x1ff, /* bits 0-8 = HC0's ports */
HC_SHIFT = 9, /* bits 9-17 = HC1's ports */
+ DONE_IRQ_0_3 = 0x000000aa, /* DONE_IRQ ports 0,1,2,3 */
+ DONE_IRQ_4_7 = (DONE_IRQ_0_3 << HC_SHIFT), /* 4,5,6,7 */
PCI_ERR = (1 << 18),
- TRAN_LO_DONE = (1 << 19), /* 6xxx: IRQ coalescing */
- TRAN_HI_DONE = (1 << 20), /* 6xxx: IRQ coalescing */
- PORTS_0_3_COAL_DONE = (1 << 8),
- PORTS_4_7_COAL_DONE = (1 << 17),
- PORTS_0_7_COAL_DONE = (1 << 21), /* 6xxx: IRQ coalescing */
+ TRAN_COAL_LO_DONE = (1 << 19), /* transaction coalescing */
+ TRAN_COAL_HI_DONE = (1 << 20), /* transaction coalescing */
+ PORTS_0_3_COAL_DONE = (1 << 8), /* HC0 IRQ coalescing */
+ PORTS_4_7_COAL_DONE = (1 << 17), /* HC1 IRQ coalescing */
+ ALL_PORTS_COAL_DONE = (1 << 21), /* GEN_II(E) IRQ coalescing */
GPIO_INT = (1 << 22),
SELF_INT = (1 << 23),
TWSI_INT = (1 << 24),
@@ -205,6 +241,21 @@ enum {
HC_COAL_IRQ = (1 << 4), /* IRQ coalescing */
DEV_IRQ = (1 << 8), /* shift by port # */
+ /*
+ * Per-HC (Host-Controller) interrupt coalescing feature.
+ * This is present on all chip generations.
+ *
+ * Coalescing defers the interrupt until either the IO_THRESHOLD
+ * (count of completed I/Os) is met, or the TIME_THRESHOLD is met.
+ */
+ HC_IRQ_COAL_IO_THRESHOLD_OFS = 0x000c,
+ HC_IRQ_COAL_TIME_THRESHOLD_OFS = 0x0010,
+
+ SOC_LED_CTRL_OFS = 0x2c,
+ SOC_LED_CTRL_BLINK = (1 << 0), /* Active LED blink */
+ SOC_LED_CTRL_ACT_PRESENCE = (1 << 2), /* Multiplex dev presence */
+ /* with dev activity LED */
+
/* Shadow block registers */
SHD_BLK_OFS = 0x100,
SHD_CTL_AST_OFS = 0x20, /* ofs from SHD_BLK_OFS */
@@ -346,6 +397,12 @@ enum {
EDMA_ARB_CFG_OFS = 0x38,
EDMA_HALTCOND_OFS = 0x60, /* GenIIe halt conditions */
+ EDMA_UNKNOWN_RSVD_OFS = 0x6C, /* GenIIe unknown/reserved */
+
+ BMDMA_CMD_OFS = 0x224, /* bmdma command register */
+ BMDMA_STATUS_OFS = 0x228, /* bmdma status register */
+ BMDMA_PRD_LOW_OFS = 0x22c, /* bmdma PRD addr 31:0 */
+ BMDMA_PRD_HIGH_OFS = 0x230, /* bmdma PRD addr 63:32 */
/* Host private flags (hp_flags) */
MV_HP_FLAG_MSI = (1 << 0),
@@ -359,12 +416,14 @@ enum {
MV_HP_PCIE = (1 << 9), /* PCIe bus/regs: 7042 */
MV_HP_CUT_THROUGH = (1 << 10), /* can use EDMA cut-through */
MV_HP_FLAG_SOC = (1 << 11), /* SystemOnChip, no PCI */
+ MV_HP_QUIRK_LED_BLINK_EN = (1 << 12), /* is led blinking enabled? */
/* Port private flags (pp_flags) */
MV_PP_FLAG_EDMA_EN = (1 << 0), /* is EDMA engine enabled? */
MV_PP_FLAG_NCQ_EN = (1 << 1), /* is EDMA set up for NCQ? */
MV_PP_FLAG_FBS_EN = (1 << 2), /* is EDMA set up for FBS? */
MV_PP_FLAG_DELAYED_EH = (1 << 3), /* delayed dev err handling */
+ MV_PP_FLAG_FAKE_ATA_BUSY = (1 << 4), /* ignore initial ATA_DRDY */
};
#define IS_GEN_I(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_I)
@@ -433,6 +492,18 @@ struct mv_sg {
__le32 reserved;
};
+/*
+ * We keep a local cache of a few frequently accessed port
+ * registers here, to avoid having to read them (very slow)
+ * when switching between EDMA and non-EDMA modes.
+ */
+struct mv_cached_regs {
+ u32 fiscfg;
+ u32 ltmode;
+ u32 haltcond;
+ u32 unknown_rsvd;
+};
+
struct mv_port_priv {
struct mv_crqb *crqb;
dma_addr_t crqb_dma;
@@ -445,6 +516,7 @@ struct mv_port_priv {
unsigned int resp_idx;
u32 pp_flags;
+ struct mv_cached_regs cached;
unsigned int delayed_eh_pmp_map;
};
@@ -535,7 +607,7 @@ static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int port_no);
static int mv_stop_edma(struct ata_port *ap);
static int mv_stop_edma_engine(void __iomem *port_mmio);
-static void mv_edma_cfg(struct ata_port *ap, int want_ncq);
+static void mv_edma_cfg(struct ata_port *ap, int want_ncq, int want_edma);
static void mv_pmp_select(struct ata_port *ap, int pmp);
static int mv_pmp_hardreset(struct ata_link *link, unsigned int *class,
@@ -546,6 +618,14 @@ static void mv_pmp_error_handler(struct ata_port *ap);
static void mv_process_crpb_entries(struct ata_port *ap,
struct mv_port_priv *pp);
+static void mv_sff_irq_clear(struct ata_port *ap);
+static int mv_check_atapi_dma(struct ata_queued_cmd *qc);
+static void mv_bmdma_setup(struct ata_queued_cmd *qc);
+static void mv_bmdma_start(struct ata_queued_cmd *qc);
+static void mv_bmdma_stop(struct ata_queued_cmd *qc);
+static u8 mv_bmdma_status(struct ata_port *ap);
+static u8 mv_sff_check_status(struct ata_port *ap);
+
/* .sg_tablesize is (MV_MAX_SG_CT / 2) in the structures below
* because we have to allow room for worst case splitting of
* PRDs for 64K boundaries in mv_fill_sg().
@@ -566,6 +646,8 @@ static struct scsi_host_template mv6_sht = {
static struct ata_port_operations mv5_ops = {
.inherits = &ata_sff_port_ops,
+ .lost_interrupt = ATA_OP_NULL,
+
.qc_defer = mv_qc_defer,
.qc_prep = mv_qc_prep,
.qc_issue = mv_qc_issue,
@@ -593,6 +675,14 @@ static struct ata_port_operations mv6_ops = {
.pmp_softreset = mv_softreset,
.softreset = mv_softreset,
.error_handler = mv_pmp_error_handler,
+
+ .sff_check_status = mv_sff_check_status,
+ .sff_irq_clear = mv_sff_irq_clear,
+ .check_atapi_dma = mv_check_atapi_dma,
+ .bmdma_setup = mv_bmdma_setup,
+ .bmdma_start = mv_bmdma_start,
+ .bmdma_stop = mv_bmdma_stop,
+ .bmdma_status = mv_bmdma_status,
};
static struct ata_port_operations mv_iie_ops = {
@@ -603,53 +693,49 @@ static struct ata_port_operations mv_iie_ops = {
static const struct ata_port_info mv_port_info[] = {
{ /* chip_504x */
- .flags = MV_COMMON_FLAGS,
+ .flags = MV_GEN_I_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_508x */
- .flags = MV_COMMON_FLAGS | MV_FLAG_DUAL_HC,
+ .flags = MV_GEN_I_FLAGS | MV_FLAG_DUAL_HC,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_5080 */
- .flags = MV_COMMON_FLAGS | MV_FLAG_DUAL_HC,
+ .flags = MV_GEN_I_FLAGS | MV_FLAG_DUAL_HC,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_604x */
- .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ,
+ .flags = MV_GEN_II_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv6_ops,
},
{ /* chip_608x */
- .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ | MV_FLAG_DUAL_HC,
+ .flags = MV_GEN_II_FLAGS | MV_FLAG_DUAL_HC,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv6_ops,
},
{ /* chip_6042 */
- .flags = MV_GENIIE_FLAGS,
+ .flags = MV_GEN_IIE_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
{ /* chip_7042 */
- .flags = MV_GENIIE_FLAGS,
+ .flags = MV_GEN_IIE_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
{ /* chip_soc */
- .flags = MV_GENIIE_FLAGS,
+ .flags = MV_GEN_IIE_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
@@ -794,6 +880,44 @@ static inline int mv_get_hc_count(unsigned long port_flags)
return ((port_flags & MV_FLAG_DUAL_HC) ? 2 : 1);
}
+/**
+ * mv_save_cached_regs - (re-)initialize cached port registers
+ * @ap: the port whose registers we are caching
+ *
+ * Initialize the local cache of port registers,
+ * so that reading them over and over again can
+ * be avoided on the hotter paths of this driver.
+ * This saves a few microseconds each time we switch
+ * to/from EDMA mode to perform (eg.) a drive cache flush.
+ */
+static void mv_save_cached_regs(struct ata_port *ap)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+ struct mv_port_priv *pp = ap->private_data;
+
+ pp->cached.fiscfg = readl(port_mmio + FISCFG_OFS);
+ pp->cached.ltmode = readl(port_mmio + LTMODE_OFS);
+ pp->cached.haltcond = readl(port_mmio + EDMA_HALTCOND_OFS);
+ pp->cached.unknown_rsvd = readl(port_mmio + EDMA_UNKNOWN_RSVD_OFS);
+}
+
+/**
+ * mv_write_cached_reg - write to a cached port register
+ * @addr: hardware address of the register
+ * @old: pointer to cached value of the register
+ * @new: new value for the register
+ *
+ * Write a new value to a cached register,
+ * but only if the value is different from before.
+ */
+static inline void mv_write_cached_reg(void __iomem *addr, u32 *old, u32 new)
+{
+ if (new != *old) {
+ *old = new;
+ writel(new, addr);
+ }
+}
+
static void mv_set_edma_ptrs(void __iomem *port_mmio,
struct mv_host_priv *hpriv,
struct mv_port_priv *pp)
@@ -825,6 +949,23 @@ static void mv_set_edma_ptrs(void __iomem *port_mmio,
port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
}
+static void mv_write_main_irq_mask(u32 mask, struct mv_host_priv *hpriv)
+{
+ /*
+ * When writing to the main_irq_mask in hardware,
+ * we must ensure exclusivity between the interrupt coalescing bits
+ * and the corresponding individual port DONE_IRQ bits.
+ *
+ * Note that this register is really an "IRQ enable" register,
+ * not an "IRQ mask" register as Marvell's naming might suggest.
+ */
+ if (mask & (ALL_PORTS_COAL_DONE | PORTS_0_3_COAL_DONE))
+ mask &= ~DONE_IRQ_0_3;
+ if (mask & (ALL_PORTS_COAL_DONE | PORTS_4_7_COAL_DONE))
+ mask &= ~DONE_IRQ_4_7;
+ writelfl(mask, hpriv->main_irq_mask_addr);
+}
+
static void mv_set_main_irq_mask(struct ata_host *host,
u32 disable_bits, u32 enable_bits)
{
@@ -835,7 +976,7 @@ static void mv_set_main_irq_mask(struct ata_host *host,
new_mask = (old_mask & ~disable_bits) | enable_bits;
if (new_mask != old_mask) {
hpriv->main_irq_mask = new_mask;
- writelfl(new_mask, hpriv->main_irq_mask_addr);
+ mv_write_main_irq_mask(new_mask, hpriv);
}
}
@@ -852,8 +993,94 @@ static void mv_enable_port_irqs(struct ata_port *ap,
mv_set_main_irq_mask(ap->host, disable_bits, enable_bits);
}
+static void mv_clear_and_enable_port_irqs(struct ata_port *ap,
+ void __iomem *port_mmio,
+ unsigned int port_irqs)
+{
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ int hardport = mv_hardport_from_port(ap->port_no);
+ void __iomem *hc_mmio = mv_hc_base_from_port(
+ mv_host_base(ap->host), ap->port_no);
+ u32 hc_irq_cause;
+
+ /* clear EDMA event indicators, if any */
+ writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+
+ /* clear pending irq events */
+ hc_irq_cause = ~((DEV_IRQ | DMA_IRQ) << hardport);
+ writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
+
+ /* clear FIS IRQ Cause */
+ if (IS_GEN_IIE(hpriv))
+ writelfl(0, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
+
+ mv_enable_port_irqs(ap, port_irqs);
+}
+
+static void mv_set_irq_coalescing(struct ata_host *host,
+ unsigned int count, unsigned int usecs)
+{
+ struct mv_host_priv *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->base, *hc_mmio;
+ u32 coal_enable = 0;
+ unsigned long flags;
+ unsigned int clks, is_dual_hc = hpriv->n_ports > MV_PORTS_PER_HC;
+ const u32 coal_disable = PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE |
+ ALL_PORTS_COAL_DONE;
+
+ /* Disable IRQ coalescing if either threshold is zero */
+ if (!usecs || !count) {
+ clks = count = 0;
+ } else {
+ /* Respect maximum limits of the hardware */
+ clks = usecs * COAL_CLOCKS_PER_USEC;
+ if (clks > MAX_COAL_TIME_THRESHOLD)
+ clks = MAX_COAL_TIME_THRESHOLD;
+ if (count > MAX_COAL_IO_COUNT)
+ count = MAX_COAL_IO_COUNT;
+ }
+
+ spin_lock_irqsave(&host->lock, flags);
+ mv_set_main_irq_mask(host, coal_disable, 0);
+
+ if (is_dual_hc && !IS_GEN_I(hpriv)) {
+ /*
+ * GEN_II/GEN_IIE with dual host controllers:
+ * one set of global thresholds for the entire chip.
+ */
+ writel(clks, mmio + MV_IRQ_COAL_TIME_THRESHOLD);
+ writel(count, mmio + MV_IRQ_COAL_IO_THRESHOLD);
+ /* clear leftover coal IRQ bit */
+ writel(~ALL_PORTS_COAL_IRQ, mmio + MV_IRQ_COAL_CAUSE);
+ if (count)
+ coal_enable = ALL_PORTS_COAL_DONE;
+ clks = count = 0; /* force clearing of regular regs below */
+ }
+
+ /*
+ * All chips: independent thresholds for each HC on the chip.
+ */
+ hc_mmio = mv_hc_base_from_port(mmio, 0);
+ writel(clks, hc_mmio + HC_IRQ_COAL_TIME_THRESHOLD_OFS);
+ writel(count, hc_mmio + HC_IRQ_COAL_IO_THRESHOLD_OFS);
+ writel(~HC_COAL_IRQ, hc_mmio + HC_IRQ_CAUSE_OFS);
+ if (count)
+ coal_enable |= PORTS_0_3_COAL_DONE;
+ if (is_dual_hc) {
+ hc_mmio = mv_hc_base_from_port(mmio, MV_PORTS_PER_HC);
+ writel(clks, hc_mmio + HC_IRQ_COAL_TIME_THRESHOLD_OFS);
+ writel(count, hc_mmio + HC_IRQ_COAL_IO_THRESHOLD_OFS);
+ writel(~HC_COAL_IRQ, hc_mmio + HC_IRQ_CAUSE_OFS);
+ if (count)
+ coal_enable |= PORTS_4_7_COAL_DONE;
+ }
+
+ mv_set_main_irq_mask(host, 0, coal_enable);
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
/**
- * mv_start_dma - Enable eDMA engine
+ * mv_start_edma - Enable eDMA engine
* @base: port base address
* @pp: port private data
*
@@ -863,7 +1090,7 @@ static void mv_enable_port_irqs(struct ata_port *ap,
* LOCKING:
* Inherited from caller.
*/
-static void mv_start_dma(struct ata_port *ap, void __iomem *port_mmio,
+static void mv_start_edma(struct ata_port *ap, void __iomem *port_mmio,
struct mv_port_priv *pp, u8 protocol)
{
int want_ncq = (protocol == ATA_PROT_NCQ);
@@ -875,26 +1102,11 @@ static void mv_start_dma(struct ata_port *ap, void __iomem *port_mmio,
}
if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN)) {
struct mv_host_priv *hpriv = ap->host->private_data;
- int hardport = mv_hardport_from_port(ap->port_no);
- void __iomem *hc_mmio = mv_hc_base_from_port(
- mv_host_base(ap->host), ap->port_no);
- u32 hc_irq_cause;
-
- /* clear EDMA event indicators, if any */
- writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
- /* clear pending irq events */
- hc_irq_cause = ~((DEV_IRQ | DMA_IRQ) << hardport);
- writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
-
- mv_edma_cfg(ap, want_ncq);
-
- /* clear FIS IRQ Cause */
- if (IS_GEN_IIE(hpriv))
- writelfl(0, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
+ mv_edma_cfg(ap, want_ncq, 1);
mv_set_edma_ptrs(port_mmio, hpriv, pp);
- mv_enable_port_irqs(ap, DONE_IRQ|ERR_IRQ);
+ mv_clear_and_enable_port_irqs(ap, port_mmio, DONE_IRQ|ERR_IRQ);
writelfl(EDMA_EN, port_mmio + EDMA_CMD_OFS);
pp->pp_flags |= MV_PP_FLAG_EDMA_EN;
@@ -952,6 +1164,7 @@ static int mv_stop_edma(struct ata_port *ap)
{
void __iomem *port_mmio = mv_ap_base(ap);
struct mv_port_priv *pp = ap->private_data;
+ int err = 0;
if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN))
return 0;
@@ -959,9 +1172,10 @@ static int mv_stop_edma(struct ata_port *ap)
mv_wait_for_edma_empty_idle(ap);
if (mv_stop_edma_engine(port_mmio)) {
ata_port_printk(ap, KERN_ERR, "Unable to stop eDMA\n");
- return -EIO;
+ err = -EIO;
}
- return 0;
+ mv_edma_cfg(ap, 0, 0);
+ return err;
}
#ifdef ATA_DEBUG
@@ -1130,35 +1344,33 @@ static int mv_qc_defer(struct ata_queued_cmd *qc)
return ATA_DEFER_PORT;
}
-static void mv_config_fbs(void __iomem *port_mmio, int want_ncq, int want_fbs)
+static void mv_config_fbs(struct ata_port *ap, int want_ncq, int want_fbs)
{
- u32 new_fiscfg, old_fiscfg;
- u32 new_ltmode, old_ltmode;
- u32 new_haltcond, old_haltcond;
+ struct mv_port_priv *pp = ap->private_data;
+ void __iomem *port_mmio;
- old_fiscfg = readl(port_mmio + FISCFG_OFS);
- old_ltmode = readl(port_mmio + LTMODE_OFS);
- old_haltcond = readl(port_mmio + EDMA_HALTCOND_OFS);
+ u32 fiscfg, *old_fiscfg = &pp->cached.fiscfg;
+ u32 ltmode, *old_ltmode = &pp->cached.ltmode;
+ u32 haltcond, *old_haltcond = &pp->cached.haltcond;
- new_fiscfg = old_fiscfg & ~(FISCFG_SINGLE_SYNC | FISCFG_WAIT_DEV_ERR);
- new_ltmode = old_ltmode & ~LTMODE_BIT8;
- new_haltcond = old_haltcond | EDMA_ERR_DEV;
+ ltmode = *old_ltmode & ~LTMODE_BIT8;
+ haltcond = *old_haltcond | EDMA_ERR_DEV;
if (want_fbs) {
- new_fiscfg = old_fiscfg | FISCFG_SINGLE_SYNC;
- new_ltmode = old_ltmode | LTMODE_BIT8;
+ fiscfg = *old_fiscfg | FISCFG_SINGLE_SYNC;
+ ltmode = *old_ltmode | LTMODE_BIT8;
if (want_ncq)
- new_haltcond &= ~EDMA_ERR_DEV;
+ haltcond &= ~EDMA_ERR_DEV;
else
- new_fiscfg |= FISCFG_WAIT_DEV_ERR;
+ fiscfg |= FISCFG_WAIT_DEV_ERR;
+ } else {
+ fiscfg = *old_fiscfg & ~(FISCFG_SINGLE_SYNC | FISCFG_WAIT_DEV_ERR);
}
- if (new_fiscfg != old_fiscfg)
- writelfl(new_fiscfg, port_mmio + FISCFG_OFS);
- if (new_ltmode != old_ltmode)
- writelfl(new_ltmode, port_mmio + LTMODE_OFS);
- if (new_haltcond != old_haltcond)
- writelfl(new_haltcond, port_mmio + EDMA_HALTCOND_OFS);
+ port_mmio = mv_ap_base(ap);
+ mv_write_cached_reg(port_mmio + FISCFG_OFS, old_fiscfg, fiscfg);
+ mv_write_cached_reg(port_mmio + LTMODE_OFS, old_ltmode, ltmode);
+ mv_write_cached_reg(port_mmio + EDMA_HALTCOND_OFS, old_haltcond, haltcond);
}
static void mv_60x1_errata_sata25(struct ata_port *ap, int want_ncq)
@@ -1176,7 +1388,86 @@ static void mv_60x1_errata_sata25(struct ata_port *ap, int want_ncq)
writel(new, hpriv->base + MV_GPIO_PORT_CTL_OFS);
}
-static void mv_edma_cfg(struct ata_port *ap, int want_ncq)
+/**
+ * mv_bmdma_enable - set a magic bit on GEN_IIE to allow bmdma
+ * @ap: Port being initialized
+ *
+ * There are two DMA modes on these chips: basic DMA, and EDMA.
+ *
+ * Bit-0 of the "EDMA RESERVED" register enables/disables use
+ * of basic DMA on the GEN_IIE versions of the chips.
+ *
+ * This bit survives EDMA resets, and must be set for basic DMA
+ * to function, and should be cleared when EDMA is active.
+ */
+static void mv_bmdma_enable_iie(struct ata_port *ap, int enable_bmdma)
+{
+ struct mv_port_priv *pp = ap->private_data;
+ u32 new, *old = &pp->cached.unknown_rsvd;
+
+ if (enable_bmdma)
+ new = *old | 1;
+ else
+ new = *old & ~1;
+ mv_write_cached_reg(mv_ap_base(ap) + EDMA_UNKNOWN_RSVD_OFS, old, new);
+}
+
+/*
+ * SOC chips have an issue whereby the HDD LEDs don't always blink
+ * during I/O when NCQ is enabled. Enabling a special "LED blink" mode
+ * of the SOC takes care of it, generating a steady blink rate when
+ * any drive on the chip is active.
+ *
+ * Unfortunately, the blink mode is a global hardware setting for the SOC,
+ * so we must use it whenever at least one port on the SOC has NCQ enabled.
+ *
+ * We turn "LED blink" off when NCQ is not in use anywhere, because the normal
+ * LED operation works then, and provides better (more accurate) feedback.
+ *
+ * Note that this code assumes that an SOC never has more than one HC onboard.
+ */
+static void mv_soc_led_blink_enable(struct ata_port *ap)
+{
+ struct ata_host *host = ap->host;
+ struct mv_host_priv *hpriv = host->private_data;
+ void __iomem *hc_mmio;
+ u32 led_ctrl;
+
+ if (hpriv->hp_flags & MV_HP_QUIRK_LED_BLINK_EN)
+ return;
+ hpriv->hp_flags |= MV_HP_QUIRK_LED_BLINK_EN;
+ hc_mmio = mv_hc_base_from_port(mv_host_base(host), ap->port_no);
+ led_ctrl = readl(hc_mmio + SOC_LED_CTRL_OFS);
+ writel(led_ctrl | SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL_OFS);
+}
+
+static void mv_soc_led_blink_disable(struct ata_port *ap)
+{
+ struct ata_host *host = ap->host;
+ struct mv_host_priv *hpriv = host->private_data;
+ void __iomem *hc_mmio;
+ u32 led_ctrl;
+ unsigned int port;
+
+ if (!(hpriv->hp_flags & MV_HP_QUIRK_LED_BLINK_EN))
+ return;
+
+ /* disable led-blink only if no ports are using NCQ */
+ for (port = 0; port < hpriv->n_ports; port++) {
+ struct ata_port *this_ap = host->ports[port];
+ struct mv_port_priv *pp = this_ap->private_data;
+
+ if (pp->pp_flags & MV_PP_FLAG_NCQ_EN)
+ return;
+ }
+
+ hpriv->hp_flags &= ~MV_HP_QUIRK_LED_BLINK_EN;
+ hc_mmio = mv_hc_base_from_port(mv_host_base(host), ap->port_no);
+ led_ctrl = readl(hc_mmio + SOC_LED_CTRL_OFS);
+ writel(led_ctrl & ~SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL_OFS);
+}
+
+static void mv_edma_cfg(struct ata_port *ap, int want_ncq, int want_edma)
{
u32 cfg;
struct mv_port_priv *pp = ap->private_data;
@@ -1185,7 +1476,8 @@ static void mv_edma_cfg(struct ata_port *ap, int want_ncq)
/* set up non-NCQ EDMA configuration */
cfg = EDMA_CFG_Q_DEPTH; /* always 0x1f for *all* chips */
- pp->pp_flags &= ~MV_PP_FLAG_FBS_EN;
+ pp->pp_flags &=
+ ~(MV_PP_FLAG_FBS_EN | MV_PP_FLAG_NCQ_EN | MV_PP_FLAG_FAKE_ATA_BUSY);
if (IS_GEN_I(hpriv))
cfg |= (1 << 8); /* enab config burst size mask */
@@ -1206,7 +1498,7 @@ static void mv_edma_cfg(struct ata_port *ap, int want_ncq)
*/
want_fbs &= want_ncq;
- mv_config_fbs(port_mmio, want_ncq, want_fbs);
+ mv_config_fbs(ap, want_ncq, want_fbs);
if (want_fbs) {
pp->pp_flags |= MV_PP_FLAG_FBS_EN;
@@ -1214,18 +1506,27 @@ static void mv_edma_cfg(struct ata_port *ap, int want_ncq)
}
cfg |= (1 << 23); /* do not mask PM field in rx'd FIS */
- cfg |= (1 << 22); /* enab 4-entry host queue cache */
- if (!IS_SOC(hpriv))
- cfg |= (1 << 18); /* enab early completion */
+ if (want_edma) {
+ cfg |= (1 << 22); /* enab 4-entry host queue cache */
+ if (!IS_SOC(hpriv))
+ cfg |= (1 << 18); /* enab early completion */
+ }
if (hpriv->hp_flags & MV_HP_CUT_THROUGH)
cfg |= (1 << 17); /* enab cut-thru (dis stor&forwrd) */
+ mv_bmdma_enable_iie(ap, !want_edma);
+
+ if (IS_SOC(hpriv)) {
+ if (want_ncq)
+ mv_soc_led_blink_enable(ap);
+ else
+ mv_soc_led_blink_disable(ap);
+ }
}
if (want_ncq) {
cfg |= EDMA_CFG_NCQ;
pp->pp_flags |= MV_PP_FLAG_NCQ_EN;
- } else
- pp->pp_flags &= ~MV_PP_FLAG_NCQ_EN;
+ }
writelfl(cfg, port_mmio + EDMA_CFG_OFS);
}
@@ -1309,6 +1610,8 @@ static int mv_port_start(struct ata_port *ap)
pp->sg_tbl_dma[tag] = pp->sg_tbl_dma[0];
}
}
+ mv_save_cached_regs(ap);
+ mv_edma_cfg(ap, 0, 0);
return 0;
out_port_free_dma_mem:
@@ -1357,12 +1660,13 @@ static void mv_fill_sg(struct ata_queued_cmd *qc)
u32 offset = addr & 0xffff;
u32 len = sg_len;
- if ((offset + sg_len > 0x10000))
+ if (offset + len > 0x10000)
len = 0x10000 - offset;
mv_sg->addr = cpu_to_le32(addr & 0xffffffff);
mv_sg->addr_hi = cpu_to_le32((addr >> 16) >> 16);
mv_sg->flags_size = cpu_to_le32(len & 0xffff);
+ mv_sg->reserved = 0;
sg_len -= len;
addr += len;
@@ -1374,6 +1678,7 @@ static void mv_fill_sg(struct ata_queued_cmd *qc)
if (likely(last_sg))
last_sg->flags_size |= cpu_to_le32(EPRD_FLAG_END_OF_TBL);
+ mb(); /* ensure data structure is visible to the chipset */
}
static void mv_crqb_pack_cmd(__le16 *cmdw, u8 data, u8 addr, unsigned last)
@@ -1384,6 +1689,147 @@ static void mv_crqb_pack_cmd(__le16 *cmdw, u8 data, u8 addr, unsigned last)
}
/**
+ * mv_sff_irq_clear - Clear hardware interrupt after DMA.
+ * @ap: Port associated with this ATA transaction.
+ *
+ * We need this only for ATAPI bmdma transactions,
+ * as otherwise we experience spurious interrupts
+ * after libata-sff handles the bmdma interrupts.
+ */
+static void mv_sff_irq_clear(struct ata_port *ap)
+{
+ mv_clear_and_enable_port_irqs(ap, mv_ap_base(ap), ERR_IRQ);
+}
+
+/**
+ * mv_check_atapi_dma - Filter ATAPI cmds which are unsuitable for DMA.
+ * @qc: queued command to check for chipset/DMA compatibility.
+ *
+ * The bmdma engines cannot handle speculative data sizes
+ * (bytecount under/over flow). So only allow DMA for
+ * data transfer commands with known data sizes.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static int mv_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+ struct scsi_cmnd *scmd = qc->scsicmd;
+
+ if (scmd) {
+ switch (scmd->cmnd[0]) {
+ case READ_6:
+ case READ_10:
+ case READ_12:
+ case WRITE_6:
+ case WRITE_10:
+ case WRITE_12:
+ case GPCMD_READ_CD:
+ case GPCMD_SEND_DVD_STRUCTURE:
+ case GPCMD_SEND_CUE_SHEET:
+ return 0; /* DMA is safe */
+ }
+ }
+ return -EOPNOTSUPP; /* use PIO instead */
+}
+
+/**
+ * mv_bmdma_setup - Set up BMDMA transaction
+ * @qc: queued command to prepare DMA for.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static void mv_bmdma_setup(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ void __iomem *port_mmio = mv_ap_base(ap);
+ struct mv_port_priv *pp = ap->private_data;
+
+ mv_fill_sg(qc);
+
+ /* clear all DMA cmd bits */
+ writel(0, port_mmio + BMDMA_CMD_OFS);
+
+ /* load PRD table addr. */
+ writel((pp->sg_tbl_dma[qc->tag] >> 16) >> 16,
+ port_mmio + BMDMA_PRD_HIGH_OFS);
+ writelfl(pp->sg_tbl_dma[qc->tag],
+ port_mmio + BMDMA_PRD_LOW_OFS);
+
+ /* issue r/w command */
+ ap->ops->sff_exec_command(ap, &qc->tf);
+}
+
+/**
+ * mv_bmdma_start - Start a BMDMA transaction
+ * @qc: queued command to start DMA on.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static void mv_bmdma_start(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ void __iomem *port_mmio = mv_ap_base(ap);
+ unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
+ u32 cmd = (rw ? 0 : ATA_DMA_WR) | ATA_DMA_START;
+
+ /* start host DMA transaction */
+ writelfl(cmd, port_mmio + BMDMA_CMD_OFS);
+}
+
+/**
+ * mv_bmdma_stop - Stop BMDMA transfer
+ * @qc: queued command to stop DMA on.
+ *
+ * Clears the ATA_DMA_START flag in the bmdma control register
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static void mv_bmdma_stop(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ void __iomem *port_mmio = mv_ap_base(ap);
+ u32 cmd;
+
+ /* clear start/stop bit */
+ cmd = readl(port_mmio + BMDMA_CMD_OFS);
+ cmd &= ~ATA_DMA_START;
+ writelfl(cmd, port_mmio + BMDMA_CMD_OFS);
+
+ /* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */
+ ata_sff_dma_pause(ap);
+}
+
+/**
+ * mv_bmdma_status - Read BMDMA status
+ * @ap: port for which to retrieve DMA status.
+ *
+ * Read and return equivalent of the sff BMDMA status register.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static u8 mv_bmdma_status(struct ata_port *ap)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+ u32 reg, status;
+
+ /*
+ * Other bits are valid only if ATA_DMA_ACTIVE==0,
+ * and the ATA_DMA_INTR bit doesn't exist.
+ */
+ reg = readl(port_mmio + BMDMA_STATUS_OFS);
+ if (reg & ATA_DMA_ACTIVE)
+ status = ATA_DMA_ACTIVE;
+ else
+ status = (reg & ATA_DMA_ERR) | ATA_DMA_INTR;
+ return status;
+}
+
+/**
* mv_qc_prep - Host specific command preparation.
* @qc: queued command to prepare
*
@@ -1545,6 +1991,132 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc)
}
/**
+ * mv_sff_check_status - fetch device status, if valid
+ * @ap: ATA port to fetch status from
+ *
+ * When using command issue via mv_qc_issue_fis(),
+ * the initial ATA_BUSY state does not show up in the
+ * ATA status (shadow) register. This can confuse libata!
+ *
+ * So we have a hook here to fake ATA_BUSY for that situation,
+ * until the first time a BUSY, DRQ, or ERR bit is seen.
+ *
+ * The rest of the time, it simply returns the ATA status register.
+ */
+static u8 mv_sff_check_status(struct ata_port *ap)
+{
+ u8 stat = ioread8(ap->ioaddr.status_addr);
+ struct mv_port_priv *pp = ap->private_data;
+
+ if (pp->pp_flags & MV_PP_FLAG_FAKE_ATA_BUSY) {
+ if (stat & (ATA_BUSY | ATA_DRQ | ATA_ERR))
+ pp->pp_flags &= ~MV_PP_FLAG_FAKE_ATA_BUSY;
+ else
+ stat = ATA_BUSY;
+ }
+ return stat;
+}
+
+/**
+ * mv_send_fis - Send a FIS, using the "Vendor-Unique FIS" register
+ * @fis: fis to be sent
+ * @nwords: number of 32-bit words in the fis
+ */
+static unsigned int mv_send_fis(struct ata_port *ap, u32 *fis, int nwords)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+ u32 ifctl, old_ifctl, ifstat;
+ int i, timeout = 200, final_word = nwords - 1;
+
+ /* Initiate FIS transmission mode */
+ old_ifctl = readl(port_mmio + SATA_IFCTL_OFS);
+ ifctl = 0x100 | (old_ifctl & 0xf);
+ writelfl(ifctl, port_mmio + SATA_IFCTL_OFS);
+
+ /* Send all words of the FIS except for the final word */
+ for (i = 0; i < final_word; ++i)
+ writel(fis[i], port_mmio + VENDOR_UNIQUE_FIS_OFS);
+
+ /* Flag end-of-transmission, and then send the final word */
+ writelfl(ifctl | 0x200, port_mmio + SATA_IFCTL_OFS);
+ writelfl(fis[final_word], port_mmio + VENDOR_UNIQUE_FIS_OFS);
+
+ /*
+ * Wait for FIS transmission to complete.
+ * This typically takes just a single iteration.
+ */
+ do {
+ ifstat = readl(port_mmio + SATA_IFSTAT_OFS);
+ } while (!(ifstat & 0x1000) && --timeout);
+
+ /* Restore original port configuration */
+ writelfl(old_ifctl, port_mmio + SATA_IFCTL_OFS);
+
+ /* See if it worked */
+ if ((ifstat & 0x3000) != 0x1000) {
+ ata_port_printk(ap, KERN_WARNING,
+ "%s transmission error, ifstat=%08x\n",
+ __func__, ifstat);
+ return AC_ERR_OTHER;
+ }
+ return 0;
+}
+
+/**
+ * mv_qc_issue_fis - Issue a command directly as a FIS
+ * @qc: queued command to start
+ *
+ * Note that the ATA shadow registers are not updated
+ * after command issue, so the device will appear "READY"
+ * if polled, even while it is BUSY processing the command.
+ *
+ * So we use a status hook to fake ATA_BUSY until the drive changes state.
+ *
+ * Note: we don't get updated shadow regs on *completion*
+ * of non-data commands. So avoid sending them via this function,
+ * as they will appear to have completed immediately.
+ *
+ * GEN_IIE has special registers that we could get the result tf from,
+ * but earlier chipsets do not. For now, we ignore those registers.
+ */
+static unsigned int mv_qc_issue_fis(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct mv_port_priv *pp = ap->private_data;
+ struct ata_link *link = qc->dev->link;
+ u32 fis[5];
+ int err = 0;
+
+ ata_tf_to_fis(&qc->tf, link->pmp, 1, (void *)fis);
+ err = mv_send_fis(ap, fis, sizeof(fis) / sizeof(fis[0]));
+ if (err)
+ return err;
+
+ switch (qc->tf.protocol) {
+ case ATAPI_PROT_PIO:
+ pp->pp_flags |= MV_PP_FLAG_FAKE_ATA_BUSY;
+ /* fall through */
+ case ATAPI_PROT_NODATA:
+ ap->hsm_task_state = HSM_ST_FIRST;
+ break;
+ case ATA_PROT_PIO:
+ pp->pp_flags |= MV_PP_FLAG_FAKE_ATA_BUSY;
+ if (qc->tf.flags & ATA_TFLAG_WRITE)
+ ap->hsm_task_state = HSM_ST_FIRST;
+ else
+ ap->hsm_task_state = HSM_ST;
+ break;
+ default:
+ ap->hsm_task_state = HSM_ST_LAST;
+ break;
+ }
+
+ if (qc->tf.flags & ATA_TFLAG_POLLING)
+ ata_pio_queue_task(ap, qc, 0);
+ return 0;
+}
+
+/**
* mv_qc_issue - Initiate a command to the host
* @qc: queued command to start
*
@@ -1558,14 +2130,28 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc)
*/
static unsigned int mv_qc_issue(struct ata_queued_cmd *qc)
{
+ static int limit_warnings = 10;
struct ata_port *ap = qc->ap;
void __iomem *port_mmio = mv_ap_base(ap);
struct mv_port_priv *pp = ap->private_data;
u32 in_index;
+ unsigned int port_irqs;
- if ((qc->tf.protocol != ATA_PROT_DMA) &&
- (qc->tf.protocol != ATA_PROT_NCQ)) {
- static int limit_warnings = 10;
+ pp->pp_flags &= ~MV_PP_FLAG_FAKE_ATA_BUSY; /* paranoia */
+
+ switch (qc->tf.protocol) {
+ case ATA_PROT_DMA:
+ case ATA_PROT_NCQ:
+ mv_start_edma(ap, port_mmio, pp, qc->tf.protocol);
+ pp->req_idx = (pp->req_idx + 1) & MV_MAX_Q_DEPTH_MASK;
+ in_index = pp->req_idx << EDMA_REQ_Q_PTR_SHIFT;
+
+ /* Write the request in pointer to kick the EDMA to life */
+ writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | in_index,
+ port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
+ return 0;
+
+ case ATA_PROT_PIO:
/*
* Errata SATA#16, SATA#24: warn if multiple DRQs expected.
*
@@ -1583,27 +2169,46 @@ static unsigned int mv_qc_issue(struct ata_queued_cmd *qc)
": attempting PIO w/multiple DRQ: "
"this may fail due to h/w errata\n");
}
- /*
- * We're about to send a non-EDMA capable command to the
- * port. Turn off EDMA so there won't be problems accessing
- * shadow block, etc registers.
- */
- mv_stop_edma(ap);
- mv_enable_port_irqs(ap, ERR_IRQ);
- mv_pmp_select(ap, qc->dev->link->pmp);
- return ata_sff_qc_issue(qc);
+ /* drop through */
+ case ATA_PROT_NODATA:
+ case ATAPI_PROT_PIO:
+ case ATAPI_PROT_NODATA:
+ if (ap->flags & ATA_FLAG_PIO_POLLING)
+ qc->tf.flags |= ATA_TFLAG_POLLING;
+ break;
}
- mv_start_dma(ap, port_mmio, pp, qc->tf.protocol);
-
- pp->req_idx = (pp->req_idx + 1) & MV_MAX_Q_DEPTH_MASK;
- in_index = pp->req_idx << EDMA_REQ_Q_PTR_SHIFT;
+ if (qc->tf.flags & ATA_TFLAG_POLLING)
+ port_irqs = ERR_IRQ; /* mask device interrupt when polling */
+ else
+ port_irqs = ERR_IRQ | DONE_IRQ; /* unmask all interrupts */
- /* and write the request in pointer to kick the EDMA to life */
- writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | in_index,
- port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
+ /*
+ * We're about to send a non-EDMA capable command to the
+ * port. Turn off EDMA so there won't be problems accessing
+ * shadow block, etc registers.
+ */
+ mv_stop_edma(ap);
+ mv_clear_and_enable_port_irqs(ap, mv_ap_base(ap), port_irqs);
+ mv_pmp_select(ap, qc->dev->link->pmp);
- return 0;
+ if (qc->tf.command == ATA_CMD_READ_LOG_EXT) {
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ /*
+ * Workaround for 88SX60x1 FEr SATA#25 (part 2).
+ *
+ * After any NCQ error, the READ_LOG_EXT command
+ * from libata-eh *must* use mv_qc_issue_fis().
+ * Otherwise it might fail, due to chip errata.
+ *
+ * Rather than special-case it, we'll just *always*
+ * use this method here for READ_LOG_EXT, making for
+ * easier testing.
+ */
+ if (IS_GEN_II(hpriv))
+ return mv_qc_issue_fis(qc);
+ }
+ return ata_sff_qc_issue(qc);
}
static struct ata_queued_cmd *mv_get_active_qc(struct ata_port *ap)
@@ -1614,8 +2219,12 @@ static struct ata_queued_cmd *mv_get_active_qc(struct ata_port *ap)
if (pp->pp_flags & MV_PP_FLAG_NCQ_EN)
return NULL;
qc = ata_qc_from_tag(ap, ap->link.active_tag);
- if (qc && (qc->tf.flags & ATA_TFLAG_POLLING))
- qc = NULL;
+ if (qc) {
+ if (qc->tf.flags & ATA_TFLAG_POLLING)
+ qc = NULL;
+ else if (!(qc->flags & ATA_QCFLAG_ACTIVE))
+ qc = NULL;
+ }
return qc;
}
@@ -2084,6 +2693,10 @@ static int mv_host_intr(struct ata_host *host, u32 main_irq_cause)
void __iomem *mmio = hpriv->base, *hc_mmio;
unsigned int handled = 0, port;
+ /* If asserted, clear the "all ports" IRQ coalescing bit */
+ if (main_irq_cause & ALL_PORTS_COAL_DONE)
+ writel(~ALL_PORTS_COAL_IRQ, mmio + MV_IRQ_COAL_CAUSE);
+
for (port = 0; port < hpriv->n_ports; port++) {
struct ata_port *ap = host->ports[port];
unsigned int p, shift, hardport, port_cause;
@@ -2116,6 +2729,8 @@ static int mv_host_intr(struct ata_host *host, u32 main_irq_cause)
* to ack (only) those ports via hc_irq_cause.
*/
ack_irqs = 0;
+ if (hc_cause & PORTS_0_3_COAL_DONE)
+ ack_irqs = HC_COAL_IRQ;
for (p = 0; p < MV_PORTS_PER_HC; ++p) {
if ((port + p) >= hpriv->n_ports)
break;
@@ -2204,7 +2819,7 @@ static irqreturn_t mv_interrupt(int irq, void *dev_instance)
/* for MSI: block new interrupts while in here */
if (using_msi)
- writel(0, hpriv->main_irq_mask_addr);
+ mv_write_main_irq_mask(0, hpriv);
main_irq_cause = readl(hpriv->main_irq_cause_addr);
pending_irqs = main_irq_cause & hpriv->main_irq_mask;
@@ -2221,7 +2836,7 @@ static irqreturn_t mv_interrupt(int irq, void *dev_instance)
/* for MSI: unmask; interrupt cause bits will retrigger now */
if (using_msi)
- writel(hpriv->main_irq_mask, hpriv->main_irq_mask_addr);
+ mv_write_main_irq_mask(hpriv->main_irq_mask, hpriv);
spin_unlock(&host->lock);
@@ -2774,6 +3389,8 @@ static int mv_hardreset(struct ata_link *link, unsigned int *class,
mv_reset_channel(hpriv, mmio, ap->port_no);
pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
+ pp->pp_flags &=
+ ~(MV_PP_FLAG_FBS_EN | MV_PP_FLAG_NCQ_EN | MV_PP_FLAG_FAKE_ATA_BUSY);
/* Workaround for errata FEr SATA#10 (part 2) */
do {
@@ -2793,6 +3410,8 @@ static int mv_hardreset(struct ata_link *link, unsigned int *class,
extra = HZ; /* only extend it once, max */
}
} while (sstatus != 0x0 && sstatus != 0x113 && sstatus != 0x123);
+ mv_save_cached_regs(ap);
+ mv_edma_cfg(ap, 0, 0);
return rc;
}
@@ -3126,6 +3745,8 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
* The per-port interrupts get done later as ports are set up.
*/
mv_set_main_irq_mask(host, 0, PCI_ERR);
+ mv_set_irq_coalescing(host, irq_coalescing_io_count,
+ irq_coalescing_usecs);
done:
return rc;
}
@@ -3287,12 +3908,6 @@ static struct pci_driver mv_pci_driver = {
.remove = ata_pci_remove_one,
};
-/*
- * module options
- */
-static int msi; /* Use PCI msi; either zero (off, default) or non-zero */
-
-
/* move to PCI layer or libata core? */
static int pci_go_64(struct pci_dev *pdev)
{
@@ -3474,10 +4089,5 @@ MODULE_DEVICE_TABLE(pci, mv_pci_tbl);
MODULE_VERSION(DRV_VERSION);
MODULE_ALIAS("platform:" DRV_NAME);
-#ifdef CONFIG_PCI
-module_param(msi, int, 0444);
-MODULE_PARM_DESC(msi, "Enable use of PCI MSI (0=off, 1=on)");
-#endif
-
module_init(mv_init);
module_exit(mv_exit);
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index f65b537..6cda12b 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -57,9 +57,9 @@ enum {
NV_MMIO_BAR = 5,
NV_PORTS = 2,
- NV_PIO_MASK = 0x1f,
- NV_MWDMA_MASK = 0x07,
- NV_UDMA_MASK = 0x7f,
+ NV_PIO_MASK = ATA_PIO4,
+ NV_MWDMA_MASK = ATA_MWDMA2,
+ NV_UDMA_MASK = ATA_UDMA6,
NV_PORT0_SCR_REG_OFFSET = 0x00,
NV_PORT1_SCR_REG_OFFSET = 0x40,
@@ -408,6 +408,7 @@ static struct scsi_host_template nv_swncq_sht = {
static struct ata_port_operations nv_common_ops = {
.inherits = &ata_bmdma_port_ops,
+ .lost_interrupt = ATA_OP_NULL,
.scr_read = nv_scr_read,
.scr_write = nv_scr_write,
};
diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c
index ba9a257..b1fd7d6 100644
--- a/drivers/ata/sata_promise.c
+++ b/drivers/ata/sata_promise.c
@@ -176,7 +176,9 @@ static const struct ata_port_operations pdc_common_ops = {
.check_atapi_dma = pdc_check_atapi_dma,
.qc_prep = pdc_qc_prep,
.qc_issue = pdc_qc_issue,
+
.sff_irq_clear = pdc_irq_clear,
+ .lost_interrupt = ATA_OP_NULL,
.post_internal_cmd = pdc_post_internal_cmd,
.error_handler = pdc_error_handler,
@@ -213,8 +215,8 @@ static const struct ata_port_info pdc_port_info[] = {
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA |
PDC_FLAG_SATA_PATA,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_old_sata_ops,
},
@@ -222,8 +224,8 @@ static const struct ata_port_info pdc_port_info[] = {
[board_2037x_pata] =
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_pata_ops,
},
@@ -232,8 +234,8 @@ static const struct ata_port_info pdc_port_info[] = {
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA |
PDC_FLAG_4_PORTS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_old_sata_ops,
},
@@ -242,8 +244,8 @@ static const struct ata_port_info pdc_port_info[] = {
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS |
PDC_FLAG_4_PORTS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_pata_ops,
},
@@ -252,8 +254,8 @@ static const struct ata_port_info pdc_port_info[] = {
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA |
PDC_FLAG_GEN_II | PDC_FLAG_SATA_PATA,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_sata_ops,
},
@@ -262,8 +264,8 @@ static const struct ata_port_info pdc_port_info[] = {
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS |
PDC_FLAG_GEN_II,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_pata_ops,
},
@@ -272,8 +274,8 @@ static const struct ata_port_info pdc_port_info[] = {
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA |
PDC_FLAG_GEN_II | PDC_FLAG_4_PORTS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_sata_ops,
},
diff --git a/drivers/ata/sata_qstor.c b/drivers/ata/sata_qstor.c
index a000c86..c3936d3 100644
--- a/drivers/ata/sata_qstor.c
+++ b/drivers/ata/sata_qstor.c
@@ -147,6 +147,7 @@ static struct ata_port_operations qs_ata_ops = {
.softreset = ATA_OP_NULL,
.error_handler = qs_error_handler,
.post_internal_cmd = ATA_OP_NULL,
+ .lost_interrupt = ATA_OP_NULL,
.scr_read = qs_scr_read,
.scr_write = qs_scr_write,
@@ -160,7 +161,7 @@ static const struct ata_port_info qs_port_info[] = {
{
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | ATA_FLAG_PIO_POLLING,
- .pio_mask = 0x10, /* pio4 */
+ .pio_mask = ATA_PIO4_ONLY,
.udma_mask = ATA_UDMA6,
.port_ops = &qs_ata_ops,
},
diff --git a/drivers/ata/sata_sil.c b/drivers/ata/sata_sil.c
index d009160..e67ce8e 100644
--- a/drivers/ata/sata_sil.c
+++ b/drivers/ata/sata_sil.c
@@ -200,8 +200,8 @@ static const struct ata_port_info sil_port_info[] = {
/* sil_3112 */
{
.flags = SIL_DFL_PORT_FLAGS | SIL_FLAG_MOD15WRITE,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &sil_ops,
},
@@ -209,24 +209,24 @@ static const struct ata_port_info sil_port_info[] = {
{
.flags = SIL_DFL_PORT_FLAGS | SIL_FLAG_MOD15WRITE |
SIL_FLAG_NO_SATA_IRQ,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &sil_ops,
},
/* sil_3512 */
{
.flags = SIL_DFL_PORT_FLAGS | SIL_FLAG_RERR_ON_DMA_ACT,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &sil_ops,
},
/* sil_3114 */
{
.flags = SIL_DFL_PORT_FLAGS | SIL_FLAG_RERR_ON_DMA_ACT,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &sil_ops,
},
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index 2590c22..0d8990d 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -429,25 +429,25 @@ static const struct ata_port_info sil24_port_info[] = {
{
.flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(4) |
SIL24_FLAG_PCIX_IRQ_WOC,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = ATA_UDMA5, /* udma0-5 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &sil24_ops,
},
/* sil_3132 */
{
.flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(2),
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = ATA_UDMA5, /* udma0-5 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &sil24_ops,
},
/* sil_3131/sil_3531 */
{
.flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(1),
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = ATA_UDMA5, /* udma0-5 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &sil24_ops,
},
};
diff --git a/drivers/ata/sata_sis.c b/drivers/ata/sata_sis.c
index 9c43b4e..8f98332 100644
--- a/drivers/ata/sata_sis.c
+++ b/drivers/ata/sata_sis.c
@@ -97,8 +97,8 @@ static struct ata_port_operations sis_ops = {
static const struct ata_port_info sis_port_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x7,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &sis_ops,
};
diff --git a/drivers/ata/sata_svw.c b/drivers/ata/sata_svw.c
index 609d147..7257f2d 100644
--- a/drivers/ata/sata_svw.c
+++ b/drivers/ata/sata_svw.c
@@ -361,8 +361,8 @@ static const struct ata_port_info k2_port_info[] = {
{
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | K2_FLAG_NO_ATAPI_DMA,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &k2_sata_ops,
},
@@ -371,8 +371,8 @@ static const struct ata_port_info k2_port_info[] = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | K2_FLAG_NO_ATAPI_DMA |
K2_FLAG_SATA_8_PORTS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &k2_sata_ops,
},
@@ -380,8 +380,8 @@ static const struct ata_port_info k2_port_info[] = {
{
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | K2_FLAG_BAR_POS_3,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &k2_sata_ops,
},
@@ -389,8 +389,8 @@ static const struct ata_port_info k2_port_info[] = {
{
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &k2_sata_ops,
},
diff --git a/drivers/ata/sata_sx4.c b/drivers/ata/sata_sx4.c
index ec04b8d..dce3dcc 100644
--- a/drivers/ata/sata_sx4.c
+++ b/drivers/ata/sata_sx4.c
@@ -265,8 +265,8 @@ static const struct ata_port_info pdc_port_info[] = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_SRST | ATA_FLAG_MMIO |
ATA_FLAG_NO_ATAPI | ATA_FLAG_PIO_POLLING,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_20621_ops,
},
diff --git a/drivers/ata/sata_uli.c b/drivers/ata/sata_uli.c
index 019575b..e5bff47 100644
--- a/drivers/ata/sata_uli.c
+++ b/drivers/ata/sata_uli.c
@@ -89,7 +89,7 @@ static struct ata_port_operations uli_ops = {
static const struct ata_port_info uli_port_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_IGN_SIMPLEX,
- .pio_mask = 0x1f, /* pio0-4 */
+ .pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &uli_ops,
};
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index 5c62da9..98e8c50 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -146,24 +146,24 @@ static struct ata_port_operations vt8251_ops = {
static const struct ata_port_info vt6420_port_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &vt6420_sata_ops,
};
static struct ata_port_info vt6421_sport_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &vt6421_sata_ops,
};
static struct ata_port_info vt6421_pport_info = {
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_NO_LEGACY,
- .pio_mask = 0x1f,
- .mwdma_mask = 0,
+ .pio_mask = ATA_PIO4,
+ /* No MWDMA */
.udma_mask = ATA_UDMA6,
.port_ops = &vt6421_pata_ops,
};
@@ -171,8 +171,8 @@ static struct ata_port_info vt6421_pport_info = {
static struct ata_port_info vt8251_port_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_SLAVE_POSS |
ATA_FLAG_NO_LEGACY,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &vt8251_ops,
};
diff --git a/drivers/ata/sata_vsc.c b/drivers/ata/sata_vsc.c
index c57cdff..ed70bd2 100644
--- a/drivers/ata/sata_vsc.c
+++ b/drivers/ata/sata_vsc.c
@@ -308,6 +308,9 @@ static struct scsi_host_template vsc_sata_sht = {
static struct ata_port_operations vsc_sata_ops = {
.inherits = &ata_bmdma_port_ops,
+ /* The IRQ handling is not quite standard SFF behaviour so we
+ cannot use the default lost interrupt handler */
+ .lost_interrupt = ATA_OP_NULL,
.sff_tf_load = vsc_sata_tf_load,
.sff_tf_read = vsc_sata_tf_read,
.freeze = vsc_freeze,
@@ -345,8 +348,8 @@ static int __devinit vsc_sata_init_one(struct pci_dev *pdev,
static const struct ata_port_info pi = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &vsc_sata_ops,
};
diff --git a/include/linux/ata.h b/include/linux/ata.h
index 9a061ac..3901b00 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -108,6 +108,8 @@ enum {
ATA_PIO5 = ATA_PIO4 | (1 << 5),
ATA_PIO6 = ATA_PIO5 | (1 << 6),
+ ATA_PIO4_ONLY = (1 << 4),
+
ATA_SWDMA0 = (1 << 0),
ATA_SWDMA1 = ATA_SWDMA0 | (1 << 1),
ATA_SWDMA2 = ATA_SWDMA1 | (1 << 2),
@@ -117,6 +119,8 @@ enum {
ATA_MWDMA0 = (1 << 0),
ATA_MWDMA1 = ATA_MWDMA0 | (1 << 1),
ATA_MWDMA2 = ATA_MWDMA1 | (1 << 2),
+ ATA_MWDMA3 = ATA_MWDMA2 | (1 << 3),
+ ATA_MWDMA4 = ATA_MWDMA3 | (1 << 4),
ATA_MWDMA12_ONLY = (1 << 1) | (1 << 2),
ATA_MWDMA2_ONLY = (1 << 2),
@@ -131,6 +135,8 @@ enum {
ATA_UDMA7 = ATA_UDMA6 | (1 << 7),
/* ATA_UDMA7 is just for completeness... doesn't exist (yet?). */
+ ATA_UDMA24_ONLY = (1 << 2) | (1 << 4),
+
ATA_UDMA_MASK_40C = ATA_UDMA2, /* udma0-2 */
/* DMA-related */
diff --git a/include/linux/libata.h b/include/linux/libata.h
index dc18b87..76262d8 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -795,6 +795,7 @@ struct ata_port_operations {
ata_reset_fn_t pmp_hardreset;
ata_postreset_fn_t pmp_postreset;
void (*error_handler)(struct ata_port *ap);
+ void (*lost_interrupt)(struct ata_port *ap);
void (*post_internal_cmd)(struct ata_queued_cmd *qc);
/*
@@ -836,6 +837,8 @@ struct ata_port_operations {
void (*bmdma_start)(struct ata_queued_cmd *qc);
void (*bmdma_stop)(struct ata_queued_cmd *qc);
u8 (*bmdma_status)(struct ata_port *ap);
+
+ void (*drain_fifo)(struct ata_queued_cmd *qc);
#endif /* CONFIG_ATA_SFF */
ssize_t (*em_show)(struct ata_port *ap, char *buf);
@@ -1008,6 +1011,9 @@ extern int ata_cable_sata(struct ata_port *ap);
extern int ata_cable_ignore(struct ata_port *ap);
extern int ata_cable_unknown(struct ata_port *ap);
+extern void ata_pio_queue_task(struct ata_port *ap, void *data,
+ unsigned long delay);
+
/* Timing helpers */
extern unsigned int ata_pio_need_iordy(const struct ata_device *);
extern const struct ata_timing *ata_timing_find_mode(u8 xfer_mode);
@@ -1572,6 +1578,7 @@ extern bool ata_sff_qc_fill_rtf(struct ata_queued_cmd *qc);
extern unsigned int ata_sff_host_intr(struct ata_port *ap,
struct ata_queued_cmd *qc);
extern irqreturn_t ata_sff_interrupt(int irq, void *dev_instance);
+extern void ata_sff_lost_interrupt(struct ata_port *ap);
extern void ata_sff_freeze(struct ata_port *ap);
extern void ata_sff_thaw(struct ata_port *ap);
extern int ata_sff_prereset(struct ata_link *link, unsigned long deadline);
@@ -1584,6 +1591,7 @@ extern int ata_sff_softreset(struct ata_link *link, unsigned int *classes,
extern int sata_sff_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
extern void ata_sff_postreset(struct ata_link *link, unsigned int *classes);
+extern void ata_sff_drain_fifo(struct ata_queued_cmd *qc);
extern void ata_sff_error_handler(struct ata_port *ap);
extern void ata_sff_post_internal_cmd(struct ata_queued_cmd *qc);
extern int ata_sff_port_start(struct ata_port *ap);
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2009-02-03 4:27 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2009-02-03 4:27 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
1) 8-patch patchset from Tejun to fix eSata cable flakiness and
WD My Book issues
2) A CompactFlash (CFA) identification fix, which also affects
drivers/ide, since drivers/ide shares some definitions with libata
via include/linux/ata.h.
Other minor fixes, and an AHCI workaround for staggered spin-up ("SSS")
from Arjan related to the async stuff.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/ahci.c | 9 ++++-
drivers/ata/libata-core.c | 96 +++++++++++++++++++++++++++++++++-----------
drivers/ata/libata-eh.c | 87 +++++++++++++++++++++++++++++++++++++----
drivers/ata/libata-pmp.c | 2 +-
drivers/ata/libata-scsi.c | 1 +
drivers/ata/libata.h | 4 +-
drivers/ata/sata_mv.c | 4 +-
drivers/ata/sata_nv.c | 7 +++-
drivers/ata/sata_sil.c | 2 +-
include/linux/ata.h | 15 +++++--
include/linux/libata.h | 19 +++++----
11 files changed, 193 insertions(+), 53 deletions(-)
Arjan van de Ven (1):
ahci: add a module parameter to ignore the SSS flags for async scanning
Mark Lord (1):
sata_mv: Fix chip type for Hightpoint RocketRaid 1740/1742
Pasi Kärkkäinen (1):
[libata] sata_sil: Fix compilation error with libata debugging enabled
Randy Dunlap (1):
libata: fix kernel-doc warnings
Sergei Shtylyov (1):
ide/libata: fix ata_id_is_cfa() (take 4)
Tejun Heo (9):
sata_nv: ck804 has borked hardreset too
libata: fix EH device failure handling
libata: move ata_dev_disable() to libata-eh.c
libata: check onlineness before using SPD in sata_down_spd_limit()
libata: clear dev->ering in smarter way
libata: add @spd_limit to sata_down_spd_limit()
libata: improve probe failure handling
libata: add no penalty retry request for EH device handling routines
libata: implement HORKAGE_1_5_GBPS and apply it to WD My Book
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 77bba4c..a603bbf 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -61,9 +61,14 @@
#define EM_MSG_LED_VALUE_ON 0x00010000
static int ahci_skip_host_reset;
+static int ahci_ignore_sss;
+
module_param_named(skip_host_reset, ahci_skip_host_reset, int, 0444);
MODULE_PARM_DESC(skip_host_reset, "skip global host reset (0=don't skip, 1=skip)");
+module_param_named(ignore_sss, ahci_ignore_sss, int, 0444);
+MODULE_PARM_DESC(ignore_sss, "Ignore staggered spinup flag (0=don't ignore, 1=ignore)");
+
static int ahci_enable_alpm(struct ata_port *ap,
enum link_pm policy);
static void ahci_disable_alpm(struct ata_port *ap);
@@ -2692,8 +2697,10 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
host->iomap = pcim_iomap_table(pdev);
host->private_data = hpriv;
- if (!(hpriv->cap & HOST_CAP_SSS))
+ if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss)
host->flags |= ATA_HOST_PARALLEL_SCAN;
+ else
+ printk(KERN_INFO "ahci: SSS flag set, parallel bus scan disabled\n");
if (pi.flags & ATA_FLAG_EM)
ahci_reset_em(host);
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 88c2428..9fbf059 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -164,6 +164,11 @@ MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_VERSION);
+static bool ata_sstatus_online(u32 sstatus)
+{
+ return (sstatus & 0xf) == 0x3;
+}
+
/**
* ata_link_next - link iteration helper
* @link: the previous link, NULL to start
@@ -1015,18 +1020,6 @@ static const char *sata_spd_string(unsigned int spd)
return spd_str[spd - 1];
}
-void ata_dev_disable(struct ata_device *dev)
-{
- if (ata_dev_enabled(dev)) {
- if (ata_msg_drv(dev->link->ap))
- ata_dev_printk(dev, KERN_WARNING, "disabled\n");
- ata_acpi_on_disable(dev);
- ata_down_xfermask_limit(dev, ATA_DNXFER_FORCE_PIO0 |
- ATA_DNXFER_QUIET);
- dev->class++;
- }
-}
-
static int ata_dev_set_dipm(struct ata_device *dev, enum link_pm policy)
{
struct ata_link *link = dev->link;
@@ -2239,6 +2232,40 @@ retry:
return rc;
}
+static int ata_do_link_spd_horkage(struct ata_device *dev)
+{
+ struct ata_link *plink = ata_dev_phys_link(dev);
+ u32 target, target_limit;
+
+ if (!sata_scr_valid(plink))
+ return 0;
+
+ if (dev->horkage & ATA_HORKAGE_1_5_GBPS)
+ target = 1;
+ else
+ return 0;
+
+ target_limit = (1 << target) - 1;
+
+ /* if already on stricter limit, no need to push further */
+ if (plink->sata_spd_limit <= target_limit)
+ return 0;
+
+ plink->sata_spd_limit = target_limit;
+
+ /* Request another EH round by returning -EAGAIN if link is
+ * going faster than the target speed. Forward progress is
+ * guaranteed by setting sata_spd_limit to target_limit above.
+ */
+ if (plink->sata_spd > target) {
+ ata_dev_printk(dev, KERN_INFO,
+ "applying link speed limit horkage to %s\n",
+ sata_spd_string(target));
+ return -EAGAIN;
+ }
+ return 0;
+}
+
static inline u8 ata_dev_knobble(struct ata_device *dev)
{
struct ata_port *ap = dev->link->ap;
@@ -2329,6 +2356,10 @@ int ata_dev_configure(struct ata_device *dev)
return 0;
}
+ rc = ata_do_link_spd_horkage(dev);
+ if (rc)
+ return rc;
+
/* let ACPI work its magic */
rc = ata_acpi_on_devcfg(dev);
if (rc)
@@ -2784,7 +2815,7 @@ int ata_bus_probe(struct ata_port *ap)
/* This is the last chance, better to slow
* down than lose it.
*/
- sata_down_spd_limit(&ap->link);
+ sata_down_spd_limit(&ap->link, 0);
ata_down_xfermask_limit(dev, ATA_DNXFER_PIO);
}
}
@@ -2880,21 +2911,27 @@ void ata_port_disable(struct ata_port *ap)
/**
* sata_down_spd_limit - adjust SATA spd limit downward
* @link: Link to adjust SATA spd limit for
+ * @spd_limit: Additional limit
*
* Adjust SATA spd limit of @link downward. Note that this
* function only adjusts the limit. The change must be applied
* using sata_set_spd().
*
+ * If @spd_limit is non-zero, the speed is limited to equal to or
+ * lower than @spd_limit if such speed is supported. If
+ * @spd_limit is slower than any supported speed, only the lowest
+ * supported speed is allowed.
+ *
* LOCKING:
* Inherited from caller.
*
* RETURNS:
* 0 on success, negative errno on failure
*/
-int sata_down_spd_limit(struct ata_link *link)
+int sata_down_spd_limit(struct ata_link *link, u32 spd_limit)
{
u32 sstatus, spd, mask;
- int rc, highbit;
+ int rc, bit;
if (!sata_scr_valid(link))
return -EOPNOTSUPP;
@@ -2903,7 +2940,7 @@ int sata_down_spd_limit(struct ata_link *link)
* If not, use cached value in link->sata_spd.
*/
rc = sata_scr_read(link, SCR_STATUS, &sstatus);
- if (rc == 0)
+ if (rc == 0 && ata_sstatus_online(sstatus))
spd = (sstatus >> 4) & 0xf;
else
spd = link->sata_spd;
@@ -2913,8 +2950,8 @@ int sata_down_spd_limit(struct ata_link *link)
return -EINVAL;
/* unconditionally mask off the highest bit */
- highbit = fls(mask) - 1;
- mask &= ~(1 << highbit);
+ bit = fls(mask) - 1;
+ mask &= ~(1 << bit);
/* Mask off all speeds higher than or equal to the current
* one. Force 1.5Gbps if current SPD is not available.
@@ -2928,6 +2965,15 @@ int sata_down_spd_limit(struct ata_link *link)
if (!mask)
return -EINVAL;
+ if (spd_limit) {
+ if (mask & ((1 << spd_limit) - 1))
+ mask &= (1 << spd_limit) - 1;
+ else {
+ bit = ffs(mask) - 1;
+ mask = 1 << bit;
+ }
+ }
+
link->sata_spd_limit = mask;
ata_link_printk(link, KERN_WARNING, "limiting SATA link speed to %s\n",
@@ -4215,6 +4261,9 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
/* Devices that do not need bridging limits applied */
{ "MTRON MSP-SATA*", NULL, ATA_HORKAGE_BRIDGE_OK, },
+ /* Devices which aren't very happy with higher link speeds */
+ { "WD My Book", NULL, ATA_HORKAGE_1_5_GBPS, },
+
/* End Marker */
{ }
};
@@ -4709,8 +4758,7 @@ void swap_buf_le16(u16 *buf, unsigned int buf_words)
/**
* ata_qc_new - Request an available ATA command, for queueing
- * @ap: Port associated with device @dev
- * @dev: Device from whom we request an available command structure
+ * @ap: target port
*
* LOCKING:
* None.
@@ -5175,7 +5223,7 @@ bool ata_phys_link_online(struct ata_link *link)
u32 sstatus;
if (sata_scr_read(link, SCR_STATUS, &sstatus) == 0 &&
- (sstatus & 0xf) == 0x3)
+ ata_sstatus_online(sstatus))
return true;
return false;
}
@@ -5199,7 +5247,7 @@ bool ata_phys_link_offline(struct ata_link *link)
u32 sstatus;
if (sata_scr_read(link, SCR_STATUS, &sstatus) == 0 &&
- (sstatus & 0xf) != 0x3)
+ !ata_sstatus_online(sstatus))
return true;
return false;
}
@@ -5412,8 +5460,8 @@ void ata_dev_init(struct ata_device *dev)
dev->horkage = 0;
spin_unlock_irqrestore(ap->lock, flags);
- memset((void *)dev + ATA_DEVICE_CLEAR_OFFSET, 0,
- sizeof(*dev) - ATA_DEVICE_CLEAR_OFFSET);
+ memset((void *)dev + ATA_DEVICE_CLEAR_BEGIN, 0,
+ ATA_DEVICE_CLEAR_END - ATA_DEVICE_CLEAR_BEGIN);
dev->pio_mask = UINT_MAX;
dev->mwdma_mask = UINT_MAX;
dev->udma_mask = UINT_MAX;
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 8147a83..ce2ef04 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -82,6 +82,10 @@ enum {
ATA_EH_FASTDRAIN_INTERVAL = 3000,
ATA_EH_UA_TRIES = 5,
+
+ /* probe speed down parameters, see ata_eh_schedule_probe() */
+ ATA_EH_PROBE_TRIAL_INTERVAL = 60000, /* 1 min */
+ ATA_EH_PROBE_TRIALS = 2,
};
/* The following table determines how we sequence resets. Each entry
@@ -1176,6 +1180,32 @@ void ata_eh_qc_retry(struct ata_queued_cmd *qc)
}
/**
+ * ata_dev_disable - disable ATA device
+ * @dev: ATA device to disable
+ *
+ * Disable @dev.
+ *
+ * Locking:
+ * EH context.
+ */
+void ata_dev_disable(struct ata_device *dev)
+{
+ if (!ata_dev_enabled(dev))
+ return;
+
+ if (ata_msg_drv(dev->link->ap))
+ ata_dev_printk(dev, KERN_WARNING, "disabled\n");
+ ata_acpi_on_disable(dev);
+ ata_down_xfermask_limit(dev, ATA_DNXFER_FORCE_PIO0 | ATA_DNXFER_QUIET);
+ dev->class++;
+
+ /* From now till the next successful probe, ering is used to
+ * track probe failures. Clear accumulated device error info.
+ */
+ ata_ering_clear(&dev->ering);
+}
+
+/**
* ata_eh_detach_dev - detach ATA device
* @dev: ATA device to detach
*
@@ -1849,7 +1879,7 @@ static unsigned int ata_eh_speed_down(struct ata_device *dev,
/* speed down? */
if (verdict & ATA_EH_SPDN_SPEED_DOWN) {
/* speed down SATA link speed if possible */
- if (sata_down_spd_limit(link) == 0) {
+ if (sata_down_spd_limit(link, 0) == 0) {
action |= ATA_EH_RESET;
goto done;
}
@@ -2601,11 +2631,11 @@ int ata_eh_reset(struct ata_link *link, int classify,
}
if (try == max_tries - 1) {
- sata_down_spd_limit(link);
+ sata_down_spd_limit(link, 0);
if (slave)
- sata_down_spd_limit(slave);
+ sata_down_spd_limit(slave, 0);
} else if (rc == -EPIPE)
- sata_down_spd_limit(failed_link);
+ sata_down_spd_limit(failed_link, 0);
if (hardreset)
reset = hardreset;
@@ -2744,6 +2774,8 @@ static int ata_eh_revalidate_and_attach(struct ata_link *link,
readid_flags, dev->id);
switch (rc) {
case 0:
+ /* clear error info accumulated during probe */
+ ata_ering_clear(&dev->ering);
new_mask |= 1 << dev->devno;
break;
case -ENOENT:
@@ -2947,9 +2979,24 @@ static int ata_eh_skip_recovery(struct ata_link *link)
return 1;
}
+static int ata_count_probe_trials_cb(struct ata_ering_entry *ent, void *void_arg)
+{
+ u64 interval = msecs_to_jiffies(ATA_EH_PROBE_TRIAL_INTERVAL);
+ u64 now = get_jiffies_64();
+ int *trials = void_arg;
+
+ if (ent->timestamp < now - min(now, interval))
+ return -1;
+
+ (*trials)++;
+ return 0;
+}
+
static int ata_eh_schedule_probe(struct ata_device *dev)
{
struct ata_eh_context *ehc = &dev->link->eh_context;
+ struct ata_link *link = ata_dev_phys_link(dev);
+ int trials = 0;
if (!(ehc->i.probe_mask & (1 << dev->devno)) ||
(ehc->did_probe_mask & (1 << dev->devno)))
@@ -2962,6 +3009,25 @@ static int ata_eh_schedule_probe(struct ata_device *dev)
ehc->saved_xfer_mode[dev->devno] = 0;
ehc->saved_ncq_enabled &= ~(1 << dev->devno);
+ /* Record and count probe trials on the ering. The specific
+ * error mask used is irrelevant. Because a successful device
+ * detection clears the ering, this count accumulates only if
+ * there are consecutive failed probes.
+ *
+ * If the count is equal to or higher than ATA_EH_PROBE_TRIALS
+ * in the last ATA_EH_PROBE_TRIAL_INTERVAL, link speed is
+ * forced to 1.5Gbps.
+ *
+ * This is to work around cases where failed link speed
+ * negotiation results in device misdetection leading to
+ * infinite DEVXCHG or PHRDY CHG events.
+ */
+ ata_ering_record(&dev->ering, 0, AC_ERR_OTHER);
+ ata_ering_map(&dev->ering, ata_count_probe_trials_cb, &trials);
+
+ if (trials > ATA_EH_PROBE_TRIALS)
+ sata_down_spd_limit(link, 1);
+
return 1;
}
@@ -2969,7 +3035,11 @@ static int ata_eh_handle_dev_fail(struct ata_device *dev, int err)
{
struct ata_eh_context *ehc = &dev->link->eh_context;
- ehc->tries[dev->devno]--;
+ /* -EAGAIN from EH routine indicates retry without prejudice.
+ * The requester is responsible for ensuring forward progress.
+ */
+ if (err != -EAGAIN)
+ ehc->tries[dev->devno]--;
switch (err) {
case -ENODEV:
@@ -2979,12 +3049,13 @@ static int ata_eh_handle_dev_fail(struct ata_device *dev, int err)
/* give it just one more chance */
ehc->tries[dev->devno] = min(ehc->tries[dev->devno], 1);
case -EIO:
- if (ehc->tries[dev->devno] == 1 && dev->pio_mode > XFER_PIO_0) {
+ if (ehc->tries[dev->devno] == 1) {
/* This is the last chance, better to slow
* down than lose it.
*/
- sata_down_spd_limit(ata_dev_phys_link(dev));
- ata_down_xfermask_limit(dev, ATA_DNXFER_PIO);
+ sata_down_spd_limit(ata_dev_phys_link(dev), 0);
+ if (dev->pio_mode > XFER_PIO_0)
+ ata_down_xfermask_limit(dev, ATA_DNXFER_PIO);
}
}
diff --git a/drivers/ata/libata-pmp.c b/drivers/ata/libata-pmp.c
index 98ca07a..619f2c3 100644
--- a/drivers/ata/libata-pmp.c
+++ b/drivers/ata/libata-pmp.c
@@ -729,7 +729,7 @@ static int sata_pmp_eh_recover_pmp(struct ata_port *ap,
if (tries) {
/* consecutive revalidation failures? speed down */
if (reval_failed)
- sata_down_spd_limit(link);
+ sata_down_spd_limit(link, 0);
else
reval_failed = 1;
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 3c4c5ae..b9747fa 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -415,6 +415,7 @@ int ata_std_bios_param(struct scsi_device *sdev, struct block_device *bdev,
/**
* ata_get_identity - Handler for HDIO_GET_IDENTITY ioctl
+ * @ap: target port
* @sdev: SCSI device to get identify data for
* @arg: User buffer area for identify data
*
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index fe2839e..cea8014 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -79,7 +79,6 @@ extern int ata_build_rw_tf(struct ata_taskfile *tf, struct ata_device *dev,
u64 block, u32 n_block, unsigned int tf_flags,
unsigned int tag);
extern u64 ata_tf_read_block(struct ata_taskfile *tf, struct ata_device *dev);
-extern void ata_dev_disable(struct ata_device *dev);
extern void ata_pio_queue_task(struct ata_port *ap, void *data,
unsigned long delay);
extern void ata_port_flush_task(struct ata_port *ap);
@@ -100,7 +99,7 @@ extern int ata_dev_reread_id(struct ata_device *dev, unsigned int readid_flags);
extern int ata_dev_revalidate(struct ata_device *dev, unsigned int new_class,
unsigned int readid_flags);
extern int ata_dev_configure(struct ata_device *dev);
-extern int sata_down_spd_limit(struct ata_link *link);
+extern int sata_down_spd_limit(struct ata_link *link, u32 spd_limit);
extern int ata_down_xfermask_limit(struct ata_device *dev, unsigned int sel);
extern void ata_sg_clean(struct ata_queued_cmd *qc);
extern void ata_qc_free(struct ata_queued_cmd *qc);
@@ -160,6 +159,7 @@ extern void ata_scsi_error(struct Scsi_Host *host);
extern void ata_port_wait_eh(struct ata_port *ap);
extern void ata_eh_fastdrain_timerfn(unsigned long arg);
extern void ata_qc_schedule_eh(struct ata_queued_cmd *qc);
+extern void ata_dev_disable(struct ata_device *dev);
extern void ata_eh_detach_dev(struct ata_device *dev);
extern void ata_eh_about_to_do(struct ata_link *link, struct ata_device *dev,
unsigned int action);
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index f2d8a02..4ae1a41 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -663,8 +663,8 @@ static const struct pci_device_id mv_pci_tbl[] = {
{ PCI_VDEVICE(MARVELL, 0x5081), chip_508x },
/* RocketRAID 1720/174x have different identifiers */
{ PCI_VDEVICE(TTI, 0x1720), chip_6042 },
- { PCI_VDEVICE(TTI, 0x1740), chip_508x },
- { PCI_VDEVICE(TTI, 0x1742), chip_508x },
+ { PCI_VDEVICE(TTI, 0x1740), chip_6042 },
+ { PCI_VDEVICE(TTI, 0x1742), chip_6042 },
{ PCI_VDEVICE(MARVELL, 0x6040), chip_604x },
{ PCI_VDEVICE(MARVELL, 0x6041), chip_604x },
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index c49ad0e..444af04 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -436,11 +436,16 @@ static struct ata_port_operations nv_nf2_ops = {
.hardreset = nv_noclassify_hardreset,
};
-/* CK804 finally gets hardreset right */
+/* For initial probing after boot and hot plugging, hardreset mostly
+ * works fine on CK804 but curiously, reprobing on the initial port by
+ * rescanning or rmmod/insmod fails to acquire the initial D2H Reg FIS
+ * in somewhat undeterministic way. Use noclassify hardreset.
+ */
static struct ata_port_operations nv_ck804_ops = {
.inherits = &nv_common_ops,
.freeze = nv_ck804_freeze,
.thaw = nv_ck804_thaw,
+ .hardreset = nv_noclassify_hardreset,
.host_stop = nv_ck804_host_stop,
};
diff --git a/drivers/ata/sata_sil.c b/drivers/ata/sata_sil.c
index 9f02959..d009160 100644
--- a/drivers/ata/sata_sil.c
+++ b/drivers/ata/sata_sil.c
@@ -324,7 +324,7 @@ static void sil_fill_sg(struct ata_queued_cmd *qc)
prd->addr = cpu_to_le32(addr);
prd->flags_len = cpu_to_le32(sg_len);
- VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", pi, addr, sg_len);
+ VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", si, addr, sg_len);
last_prd = prd;
prd++;
diff --git a/include/linux/ata.h b/include/linux/ata.h
index a53318b..08a86d5 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -731,12 +731,17 @@ static inline int ata_id_current_chs_valid(const u16 *id)
static inline int ata_id_is_cfa(const u16 *id)
{
- if (id[ATA_ID_CONFIG] == 0x848A) /* Standard CF */
+ if (id[ATA_ID_CONFIG] == 0x848A) /* Traditional CF */
return 1;
- /* Could be CF hiding as standard ATA */
- if (ata_id_major_version(id) >= 3 &&
- id[ATA_ID_COMMAND_SET_1] != 0xFFFF &&
- (id[ATA_ID_COMMAND_SET_1] & (1 << 2)))
+ /*
+ * CF specs don't require specific value in the word 0 anymore and yet
+ * they forbid to report the ATA version in the word 80 and require the
+ * CFA feature set support to be indicated in the word 83 in this case.
+ * Unfortunately, some cards only follow either of this requirements,
+ * and while those that don't indicate CFA feature support need some
+ * sort of quirk list, it seems impractical for the ones that do...
+ */
+ if ((id[ATA_ID_COMMAND_SET_2] & 0xC004) == 0x4004)
return 1;
return 0;
}
diff --git a/include/linux/libata.h b/include/linux/libata.h
index bca3ba2..5d87bc0 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -380,6 +380,7 @@ enum {
ATA_HORKAGE_ATAPI_MOD16_DMA = (1 << 11), /* use ATAPI DMA for commands
not multiple of 16 bytes */
ATA_HORKAGE_FIRMWARE_WARN = (1 << 12), /* firwmare update warning */
+ ATA_HORKAGE_1_5_GBPS = (1 << 13), /* force 1.5 Gbps */
/* DMA mask for user DMA control: User visible values; DO NOT
renumber */
@@ -580,7 +581,7 @@ struct ata_device {
acpi_handle acpi_handle;
union acpi_object *gtf_cache;
#endif
- /* n_sector is used as CLEAR_OFFSET, read comment above CLEAR_OFFSET */
+ /* n_sector is CLEAR_BEGIN, read comment above CLEAR_BEGIN */
u64 n_sectors; /* size of device, if ATA */
unsigned int class; /* ATA_DEV_xxx */
unsigned long unpark_deadline;
@@ -605,20 +606,22 @@ struct ata_device {
u16 heads; /* Number of heads */
u16 sectors; /* Number of sectors per track */
- /* error history */
- int spdn_cnt;
- struct ata_ering ering;
-
union {
u16 id[ATA_ID_WORDS]; /* IDENTIFY xxx DEVICE data */
u32 gscr[SATA_PMP_GSCR_DWORDS]; /* PMP GSCR block */
};
+
+ /* error history */
+ int spdn_cnt;
+ /* ering is CLEAR_END, read comment above CLEAR_END */
+ struct ata_ering ering;
};
-/* Offset into struct ata_device. Fields above it are maintained
- * acress device init. Fields below are zeroed.
+/* Fields between ATA_DEVICE_CLEAR_BEGIN and ATA_DEVICE_CLEAR_END are
+ * cleared to zero on ata_dev_init().
*/
-#define ATA_DEVICE_CLEAR_OFFSET offsetof(struct ata_device, n_sectors)
+#define ATA_DEVICE_CLEAR_BEGIN offsetof(struct ata_device, n_sectors)
+#define ATA_DEVICE_CLEAR_END offsetof(struct ata_device, ering)
struct ata_eh_info {
struct ata_device *dev; /* offending device */
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2009-01-08 21:46 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2009-01-08 21:46 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Lots of little bits. The only notable piece is Alan's 32-bit PIO
support; but even that is small and nicely contained, thanks to the
nifty inheritance system from Tejun.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/ahci.c | 10 ++-
drivers/ata/ata_piix.c | 51 ++++++++----
drivers/ata/libata-core.c | 5 +
drivers/ata/libata-sff.c | 185 ++++++++++++++++++++++++++++---------------
drivers/ata/pata_ali.c | 107 ++++++++++++++++---------
drivers/ata/pata_amd.c | 4 +-
drivers/ata/pata_hpt366.c | 109 ++++++++++---------------
drivers/ata/pata_hpt3x3.c | 49 ++++++++++-
drivers/ata/pata_mpiix.c | 3 +-
drivers/ata/pata_platform.c | 2 +-
drivers/ata/pata_sil680.c | 4 +-
drivers/ata/sata_sil24.c | 7 --
include/linux/libata.h | 3 +
13 files changed, 336 insertions(+), 203 deletions(-)
Alan Cox (5):
pata_hpt3x3: Workarounds for chipset
pata_ali: force initialise a few bits
pata_ali: Fix and workaround for FIFO DMA bug
libata: Add 32bit PIO support
libata: clean up the SFF code for coding style
David Daney (1):
libata: Add special ata_pio_need_iordy() handling for Compact Flash.
Grant Grundler (1):
sata_sil24: remove unused sil24_port_multiplier
Jeff Garzik (1):
[libata] pata_hpt3x3: correct _freeze() function declaration
Shane Huang (2):
[libata] ahci: Add SATA GEN3 related messages
[libata] ahci: Withdraw IGN_SERR_INTERNAL for SB800 SATA
Sonic Zhang (1):
pata_platform: __pata_platform_remove() shouldn't be in discard section
Tejun Heo (2):
ata_piix: save, use saved and restore IOCFG
pata_hpt366: reimplement mode programming
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 656448c..7f701cb 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -105,7 +105,7 @@ enum {
board_ahci_ign_iferr = 2,
board_ahci_sb600 = 3,
board_ahci_mv = 4,
- board_ahci_sb700 = 5,
+ board_ahci_sb700 = 5, /* for SB700 and SB800 */
board_ahci_mcp65 = 6,
board_ahci_nopmp = 7,
@@ -439,7 +439,7 @@ static const struct ata_port_info ahci_port_info[] = {
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
- /* board_ahci_sb700 */
+ /* board_ahci_sb700, for SB700 and SB800 */
{
AHCI_HFLAGS (AHCI_HFLAG_IGN_SERR_INTERNAL),
.flags = AHCI_FLAG_COMMON,
@@ -2446,6 +2446,8 @@ static void ahci_print_info(struct ata_host *host)
speed_s = "1.5";
else if (speed == 2)
speed_s = "3";
+ else if (speed == 3)
+ speed_s = "6";
else
speed_s = "?";
@@ -2610,6 +2612,10 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
(pdev->revision == 0xa1 || pdev->revision == 0xa2))
hpriv->flags |= AHCI_HFLAG_NO_MSI;
+ /* SB800 does NOT need the workaround to ignore SERR_INTERNAL */
+ if (board_id == board_ahci_sb700 && pdev->revision >= 0x40)
+ hpriv->flags &= ~AHCI_HFLAG_IGN_SERR_INTERNAL;
+
if ((hpriv->flags & AHCI_HFLAG_NO_MSI) || pci_enable_msi(pdev))
pci_intx(pdev, 1);
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 5fdf167..887d8f4 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -154,11 +154,13 @@ struct piix_map_db {
struct piix_host_priv {
const int *map;
+ u32 saved_iocfg;
void __iomem *sidpr;
};
static int piix_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent);
+static void piix_remove_one(struct pci_dev *pdev);
static int piix_pata_prereset(struct ata_link *link, unsigned long deadline);
static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev);
static void piix_set_dmamode(struct ata_port *ap, struct ata_device *adev);
@@ -296,7 +298,7 @@ static struct pci_driver piix_pci_driver = {
.name = DRV_NAME,
.id_table = piix_pci_tbl,
.probe = piix_init_one,
- .remove = ata_pci_remove_one,
+ .remove = piix_remove_one,
#ifdef CONFIG_PM
.suspend = piix_pci_device_suspend,
.resume = piix_pci_device_resume,
@@ -308,7 +310,7 @@ static struct scsi_host_template piix_sht = {
};
static struct ata_port_operations piix_pata_ops = {
- .inherits = &ata_bmdma_port_ops,
+ .inherits = &ata_bmdma32_port_ops,
.cable_detect = ata_cable_40wire,
.set_piomode = piix_set_piomode,
.set_dmamode = piix_set_dmamode,
@@ -610,8 +612,9 @@ static const struct ich_laptop ich_laptop[] = {
static int ich_pata_cable_detect(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ struct piix_host_priv *hpriv = ap->host->private_data;
const struct ich_laptop *lap = &ich_laptop[0];
- u8 tmp, mask;
+ u8 mask;
/* Check for specials - Acer Aspire 5602WLMi */
while (lap->device) {
@@ -625,8 +628,7 @@ static int ich_pata_cable_detect(struct ata_port *ap)
/* check BIOS cable detect results */
mask = ap->port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC;
- pci_read_config_byte(pdev, PIIX_IOCFG, &tmp);
- if ((tmp & mask) == 0)
+ if ((hpriv->saved_iocfg & mask) == 0)
return ATA_CBL_PATA40;
return ATA_CBL_PATA80;
}
@@ -1350,7 +1352,7 @@ static int __devinit piix_init_sidpr(struct ata_host *host)
return 0;
}
-static void piix_iocfg_bit18_quirk(struct pci_dev *pdev)
+static void piix_iocfg_bit18_quirk(struct ata_host *host)
{
static const struct dmi_system_id sysids[] = {
{
@@ -1367,7 +1369,8 @@ static void piix_iocfg_bit18_quirk(struct pci_dev *pdev)
{ } /* terminate list */
};
- u32 iocfg;
+ struct pci_dev *pdev = to_pci_dev(host->dev);
+ struct piix_host_priv *hpriv = host->private_data;
if (!dmi_check_system(sysids))
return;
@@ -1376,12 +1379,11 @@ static void piix_iocfg_bit18_quirk(struct pci_dev *pdev)
* seem to use it to disable a channel. Clear the bit on the
* affected systems.
*/
- pci_read_config_dword(pdev, PIIX_IOCFG, &iocfg);
- if (iocfg & (1 << 18)) {
+ if (hpriv->saved_iocfg & (1 << 18)) {
dev_printk(KERN_INFO, &pdev->dev,
"applying IOCFG bit18 quirk\n");
- iocfg &= ~(1 << 18);
- pci_write_config_dword(pdev, PIIX_IOCFG, iocfg);
+ pci_write_config_dword(pdev, PIIX_IOCFG,
+ hpriv->saved_iocfg & ~(1 << 18));
}
}
@@ -1430,6 +1432,17 @@ static int __devinit piix_init_one(struct pci_dev *pdev,
if (rc)
return rc;
+ hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
+ if (!hpriv)
+ return -ENOMEM;
+
+ /* Save IOCFG, this will be used for cable detection, quirk
+ * detection and restoration on detach. This is necessary
+ * because some ACPI implementations mess up cable related
+ * bits on _STM. Reported on kernel bz#11879.
+ */
+ pci_read_config_dword(pdev, PIIX_IOCFG, &hpriv->saved_iocfg);
+
/* ICH6R may be driven by either ata_piix or ahci driver
* regardless of BIOS configuration. Make sure AHCI mode is
* off.
@@ -1441,10 +1454,6 @@ static int __devinit piix_init_one(struct pci_dev *pdev,
}
/* SATA map init can change port_info, do it before prepping host */
- hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
- if (!hpriv)
- return -ENOMEM;
-
if (port_flags & ATA_FLAG_SATA)
hpriv->map = piix_init_sata_map(pdev, port_info,
piix_map_db_table[ent->driver_data]);
@@ -1463,7 +1472,7 @@ static int __devinit piix_init_one(struct pci_dev *pdev,
}
/* apply IOCFG bit18 quirk */
- piix_iocfg_bit18_quirk(pdev);
+ piix_iocfg_bit18_quirk(host);
/* On ICH5, some BIOSen disable the interrupt using the
* PCI_COMMAND_INTX_DISABLE bit added in PCI 2.3.
@@ -1488,6 +1497,16 @@ static int __devinit piix_init_one(struct pci_dev *pdev,
return ata_pci_sff_activate_host(host, ata_sff_interrupt, &piix_sht);
}
+static void piix_remove_one(struct pci_dev *pdev)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ struct piix_host_priv *hpriv = host->private_data;
+
+ pci_write_config_dword(pdev, PIIX_IOCFG, hpriv->saved_iocfg);
+
+ ata_pci_remove_one(pdev);
+}
+
static int __init piix_init(void)
{
int rc;
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index f178a45..175df54 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -1007,6 +1007,7 @@ static const char *sata_spd_string(unsigned int spd)
static const char * const spd_str[] = {
"1.5 Gbps",
"3.0 Gbps",
+ "6.0 Gbps",
};
if (spd == 0 || (spd - 1) >= ARRAY_SIZE(spd_str))
@@ -2000,6 +2001,10 @@ unsigned int ata_pio_need_iordy(const struct ata_device *adev)
as the caller should know this */
if (adev->link->ap->flags & ATA_FLAG_NO_IORDY)
return 0;
+ /* CF spec. r4.1 Table 22 says no iordy on PIO5 and PIO6. */
+ if (ata_id_is_cfa(adev->id)
+ && (adev->pio_mode == XFER_PIO_5 || adev->pio_mode == XFER_PIO_6))
+ return 0;
/* PIO3 and higher it is mandatory */
if (adev->pio_mode > XFER_PIO_2)
return 1;
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index 9033d16..c59ad76 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -66,6 +66,7 @@ const struct ata_port_operations ata_sff_port_ops = {
.port_start = ata_sff_port_start,
};
+EXPORT_SYMBOL_GPL(ata_sff_port_ops);
const struct ata_port_operations ata_bmdma_port_ops = {
.inherits = &ata_sff_port_ops,
@@ -77,6 +78,14 @@ const struct ata_port_operations ata_bmdma_port_ops = {
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
};
+EXPORT_SYMBOL_GPL(ata_bmdma_port_ops);
+
+const struct ata_port_operations ata_bmdma32_port_ops = {
+ .inherits = &ata_bmdma_port_ops,
+
+ .sff_data_xfer = ata_sff_data_xfer32,
+};
+EXPORT_SYMBOL_GPL(ata_bmdma32_port_ops);
/**
* ata_fill_sg - Fill PCI IDE PRD table
@@ -166,8 +175,9 @@ static void ata_fill_sg_dumb(struct ata_queued_cmd *qc)
blen = len & 0xffff;
ap->prd[pi].addr = cpu_to_le32(addr);
if (blen == 0) {
- /* Some PATA chipsets like the CS5530 can't
- cope with 0x0000 meaning 64K as the spec says */
+ /* Some PATA chipsets like the CS5530 can't
+ cope with 0x0000 meaning 64K as the spec
+ says */
ap->prd[pi].flags_len = cpu_to_le32(0x8000);
blen = 0x8000;
ap->prd[++pi].addr = cpu_to_le32(addr + 0x8000);
@@ -200,6 +210,7 @@ void ata_sff_qc_prep(struct ata_queued_cmd *qc)
ata_fill_sg(qc);
}
+EXPORT_SYMBOL_GPL(ata_sff_qc_prep);
/**
* ata_sff_dumb_qc_prep - Prepare taskfile for submission
@@ -217,6 +228,7 @@ void ata_sff_dumb_qc_prep(struct ata_queued_cmd *qc)
ata_fill_sg_dumb(qc);
}
+EXPORT_SYMBOL_GPL(ata_sff_dumb_qc_prep);
/**
* ata_sff_check_status - Read device status reg & clear interrupt
@@ -233,6 +245,7 @@ u8 ata_sff_check_status(struct ata_port *ap)
{
return ioread8(ap->ioaddr.status_addr);
}
+EXPORT_SYMBOL_GPL(ata_sff_check_status);
/**
* ata_sff_altstatus - Read device alternate status reg
@@ -275,7 +288,7 @@ static u8 ata_sff_irq_status(struct ata_port *ap)
status = ata_sff_altstatus(ap);
/* Not us: We are busy */
if (status & ATA_BUSY)
- return status;
+ return status;
}
/* Clear INTRQ latch */
status = ap->ops->sff_check_status(ap);
@@ -319,6 +332,7 @@ void ata_sff_pause(struct ata_port *ap)
ata_sff_sync(ap);
ndelay(400);
}
+EXPORT_SYMBOL_GPL(ata_sff_pause);
/**
* ata_sff_dma_pause - Pause before commencing DMA
@@ -327,7 +341,7 @@ void ata_sff_pause(struct ata_port *ap)
* Perform I/O fencing and ensure sufficient cycle delays occur
* for the HDMA1:0 transition
*/
-
+
void ata_sff_dma_pause(struct ata_port *ap)
{
if (ap->ops->sff_check_altstatus || ap->ioaddr.altstatus_addr) {
@@ -341,6 +355,7 @@ void ata_sff_dma_pause(struct ata_port *ap)
corruption. */
BUG();
}
+EXPORT_SYMBOL_GPL(ata_sff_dma_pause);
/**
* ata_sff_busy_sleep - sleep until BSY clears, or timeout
@@ -396,6 +411,7 @@ int ata_sff_busy_sleep(struct ata_port *ap,
return 0;
}
+EXPORT_SYMBOL_GPL(ata_sff_busy_sleep);
static int ata_sff_check_ready(struct ata_link *link)
{
@@ -422,6 +438,7 @@ int ata_sff_wait_ready(struct ata_link *link, unsigned long deadline)
{
return ata_wait_ready(link, deadline, ata_sff_check_ready);
}
+EXPORT_SYMBOL_GPL(ata_sff_wait_ready);
/**
* ata_sff_dev_select - Select device 0/1 on ATA bus
@@ -449,6 +466,7 @@ void ata_sff_dev_select(struct ata_port *ap, unsigned int device)
iowrite8(tmp, ap->ioaddr.device_addr);
ata_sff_pause(ap); /* needed; also flushes, for mmio */
}
+EXPORT_SYMBOL_GPL(ata_sff_dev_select);
/**
* ata_dev_select - Select device 0/1 on ATA bus
@@ -513,6 +531,7 @@ u8 ata_sff_irq_on(struct ata_port *ap)
return tmp;
}
+EXPORT_SYMBOL_GPL(ata_sff_irq_on);
/**
* ata_sff_irq_clear - Clear PCI IDE BMDMA interrupt.
@@ -534,6 +553,7 @@ void ata_sff_irq_clear(struct ata_port *ap)
iowrite8(ioread8(mmio + ATA_DMA_STATUS), mmio + ATA_DMA_STATUS);
}
+EXPORT_SYMBOL_GPL(ata_sff_irq_clear);
/**
* ata_sff_tf_load - send taskfile registers to host controller
@@ -593,6 +613,7 @@ void ata_sff_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
ata_wait_idle(ap);
}
+EXPORT_SYMBOL_GPL(ata_sff_tf_load);
/**
* ata_sff_tf_read - input device's ATA taskfile shadow registers
@@ -633,6 +654,7 @@ void ata_sff_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
WARN_ON(1);
}
}
+EXPORT_SYMBOL_GPL(ata_sff_tf_read);
/**
* ata_sff_exec_command - issue ATA command to host controller
@@ -652,6 +674,7 @@ void ata_sff_exec_command(struct ata_port *ap, const struct ata_taskfile *tf)
iowrite8(tf->command, ap->ioaddr.command_addr);
ata_sff_pause(ap);
}
+EXPORT_SYMBOL_GPL(ata_sff_exec_command);
/**
* ata_tf_to_host - issue ATA taskfile to host controller
@@ -717,6 +740,53 @@ unsigned int ata_sff_data_xfer(struct ata_device *dev, unsigned char *buf,
return words << 1;
}
+EXPORT_SYMBOL_GPL(ata_sff_data_xfer);
+
+/**
+ * ata_sff_data_xfer32 - Transfer data by PIO
+ * @dev: device to target
+ * @buf: data buffer
+ * @buflen: buffer length
+ * @rw: read/write
+ *
+ * Transfer data from/to the device data register by PIO using 32bit
+ * I/O operations.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ *
+ * RETURNS:
+ * Bytes consumed.
+ */
+
+unsigned int ata_sff_data_xfer32(struct ata_device *dev, unsigned char *buf,
+ unsigned int buflen, int rw)
+{
+ struct ata_port *ap = dev->link->ap;
+ void __iomem *data_addr = ap->ioaddr.data_addr;
+ unsigned int words = buflen >> 2;
+ int slop = buflen & 3;
+
+ /* Transfer multiple of 4 bytes */
+ if (rw == READ)
+ ioread32_rep(data_addr, buf, words);
+ else
+ iowrite32_rep(data_addr, buf, words);
+
+ if (unlikely(slop)) {
+ __le32 pad;
+ if (rw == READ) {
+ pad = cpu_to_le32(ioread32(ap->ioaddr.data_addr));
+ memcpy(buf + buflen - slop, &pad, slop);
+ } else {
+ memcpy(&pad, buf + buflen - slop, slop);
+ iowrite32(le32_to_cpu(pad), ap->ioaddr.data_addr);
+ }
+ words++;
+ }
+ return words << 2;
+}
+EXPORT_SYMBOL_GPL(ata_sff_data_xfer32);
/**
* ata_sff_data_xfer_noirq - Transfer data by PIO
@@ -746,6 +816,7 @@ unsigned int ata_sff_data_xfer_noirq(struct ata_device *dev, unsigned char *buf,
return consumed;
}
+EXPORT_SYMBOL_GPL(ata_sff_data_xfer_noirq);
/**
* ata_pio_sector - Transfer a sector of data.
@@ -922,13 +993,15 @@ next_sg:
buf = kmap_atomic(page, KM_IRQ0);
/* do the actual data transfer */
- consumed = ap->ops->sff_data_xfer(dev, buf + offset, count, rw);
+ consumed = ap->ops->sff_data_xfer(dev, buf + offset,
+ count, rw);
kunmap_atomic(buf, KM_IRQ0);
local_irq_restore(flags);
} else {
buf = page_address(page);
- consumed = ap->ops->sff_data_xfer(dev, buf + offset, count, rw);
+ consumed = ap->ops->sff_data_xfer(dev, buf + offset,
+ count, rw);
}
bytes -= min(bytes, consumed);
@@ -1013,18 +1086,19 @@ static void atapi_pio_bytes(struct ata_queued_cmd *qc)
* RETURNS:
* 1 if ok in workqueue, 0 otherwise.
*/
-static inline int ata_hsm_ok_in_wq(struct ata_port *ap, struct ata_queued_cmd *qc)
+static inline int ata_hsm_ok_in_wq(struct ata_port *ap,
+ struct ata_queued_cmd *qc)
{
if (qc->tf.flags & ATA_TFLAG_POLLING)
return 1;
if (ap->hsm_task_state == HSM_ST_FIRST) {
if (qc->tf.protocol == ATA_PROT_PIO &&
- (qc->tf.flags & ATA_TFLAG_WRITE))
+ (qc->tf.flags & ATA_TFLAG_WRITE))
return 1;
if (ata_is_atapi(qc->tf.protocol) &&
- !(qc->dev->flags & ATA_DFLAG_CDB_INTR))
+ !(qc->dev->flags & ATA_DFLAG_CDB_INTR))
return 1;
}
@@ -1338,6 +1412,7 @@ fsm_start:
return poll_next;
}
+EXPORT_SYMBOL_GPL(ata_sff_hsm_move);
void ata_pio_task(struct work_struct *work)
{
@@ -1507,6 +1582,7 @@ unsigned int ata_sff_qc_issue(struct ata_queued_cmd *qc)
return 0;
}
+EXPORT_SYMBOL_GPL(ata_sff_qc_issue);
/**
* ata_sff_qc_fill_rtf - fill result TF using ->sff_tf_read
@@ -1526,6 +1602,7 @@ bool ata_sff_qc_fill_rtf(struct ata_queued_cmd *qc)
qc->ap->ops->sff_tf_read(qc->ap, &qc->result_tf);
return true;
}
+EXPORT_SYMBOL_GPL(ata_sff_qc_fill_rtf);
/**
* ata_sff_host_intr - Handle host interrupt for given (port, task)
@@ -1623,6 +1700,7 @@ idle_irq:
#endif
return 0; /* irq not handled */
}
+EXPORT_SYMBOL_GPL(ata_sff_host_intr);
/**
* ata_sff_interrupt - Default ATA host interrupt handler
@@ -1667,6 +1745,7 @@ irqreturn_t ata_sff_interrupt(int irq, void *dev_instance)
return IRQ_RETVAL(handled);
}
+EXPORT_SYMBOL_GPL(ata_sff_interrupt);
/**
* ata_sff_freeze - Freeze SFF controller port
@@ -1695,6 +1774,7 @@ void ata_sff_freeze(struct ata_port *ap)
ap->ops->sff_irq_clear(ap);
}
+EXPORT_SYMBOL_GPL(ata_sff_freeze);
/**
* ata_sff_thaw - Thaw SFF controller port
@@ -1712,6 +1792,7 @@ void ata_sff_thaw(struct ata_port *ap)
ap->ops->sff_irq_clear(ap);
ap->ops->sff_irq_on(ap);
}
+EXPORT_SYMBOL_GPL(ata_sff_thaw);
/**
* ata_sff_prereset - prepare SFF link for reset
@@ -1753,6 +1834,7 @@ int ata_sff_prereset(struct ata_link *link, unsigned long deadline)
return 0;
}
+EXPORT_SYMBOL_GPL(ata_sff_prereset);
/**
* ata_devchk - PATA device presence detection
@@ -1865,6 +1947,7 @@ unsigned int ata_sff_dev_classify(struct ata_device *dev, int present,
return class;
}
+EXPORT_SYMBOL_GPL(ata_sff_dev_classify);
/**
* ata_sff_wait_after_reset - wait for devices to become ready after reset
@@ -1941,6 +2024,7 @@ int ata_sff_wait_after_reset(struct ata_link *link, unsigned int devmask,
return ret;
}
+EXPORT_SYMBOL_GPL(ata_sff_wait_after_reset);
static int ata_bus_softreset(struct ata_port *ap, unsigned int devmask,
unsigned long deadline)
@@ -2013,6 +2097,7 @@ int ata_sff_softreset(struct ata_link *link, unsigned int *classes,
DPRINTK("EXIT, classes[0]=%u [1]=%u\n", classes[0], classes[1]);
return 0;
}
+EXPORT_SYMBOL_GPL(ata_sff_softreset);
/**
* sata_sff_hardreset - reset host port via SATA phy reset
@@ -2045,6 +2130,7 @@ int sata_sff_hardreset(struct ata_link *link, unsigned int *class,
DPRINTK("EXIT, class=%u\n", *class);
return rc;
}
+EXPORT_SYMBOL_GPL(sata_sff_hardreset);
/**
* ata_sff_postreset - SFF postreset callback
@@ -2080,6 +2166,7 @@ void ata_sff_postreset(struct ata_link *link, unsigned int *classes)
if (ap->ioaddr.ctl_addr)
iowrite8(ap->ctl, ap->ioaddr.ctl_addr);
}
+EXPORT_SYMBOL_GPL(ata_sff_postreset);
/**
* ata_sff_error_handler - Stock error handler for BMDMA controller
@@ -2152,6 +2239,7 @@ void ata_sff_error_handler(struct ata_port *ap)
ata_do_eh(ap, ap->ops->prereset, softreset, hardreset,
ap->ops->postreset);
}
+EXPORT_SYMBOL_GPL(ata_sff_error_handler);
/**
* ata_sff_post_internal_cmd - Stock post_internal_cmd for SFF controller
@@ -2174,6 +2262,7 @@ void ata_sff_post_internal_cmd(struct ata_queued_cmd *qc)
spin_unlock_irqrestore(ap->lock, flags);
}
+EXPORT_SYMBOL_GPL(ata_sff_post_internal_cmd);
/**
* ata_sff_port_start - Set port up for dma.
@@ -2194,6 +2283,7 @@ int ata_sff_port_start(struct ata_port *ap)
return ata_port_start(ap);
return 0;
}
+EXPORT_SYMBOL_GPL(ata_sff_port_start);
/**
* ata_sff_std_ports - initialize ioaddr with standard port offsets.
@@ -2219,6 +2309,7 @@ void ata_sff_std_ports(struct ata_ioports *ioaddr)
ioaddr->status_addr = ioaddr->cmd_addr + ATA_REG_STATUS;
ioaddr->command_addr = ioaddr->cmd_addr + ATA_REG_CMD;
}
+EXPORT_SYMBOL_GPL(ata_sff_std_ports);
unsigned long ata_bmdma_mode_filter(struct ata_device *adev,
unsigned long xfer_mask)
@@ -2230,6 +2321,7 @@ unsigned long ata_bmdma_mode_filter(struct ata_device *adev,
xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
return xfer_mask;
}
+EXPORT_SYMBOL_GPL(ata_bmdma_mode_filter);
/**
* ata_bmdma_setup - Set up PCI IDE BMDMA transaction
@@ -2258,6 +2350,7 @@ void ata_bmdma_setup(struct ata_queued_cmd *qc)
/* issue r/w command */
ap->ops->sff_exec_command(ap, &qc->tf);
}
+EXPORT_SYMBOL_GPL(ata_bmdma_setup);
/**
* ata_bmdma_start - Start a PCI IDE BMDMA transaction
@@ -2290,6 +2383,7 @@ void ata_bmdma_start(struct ata_queued_cmd *qc)
* unneccessarily delayed for MMIO
*/
}
+EXPORT_SYMBOL_GPL(ata_bmdma_start);
/**
* ata_bmdma_stop - Stop PCI IDE BMDMA transfer
@@ -2314,6 +2408,7 @@ void ata_bmdma_stop(struct ata_queued_cmd *qc)
/* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */
ata_sff_dma_pause(ap);
}
+EXPORT_SYMBOL_GPL(ata_bmdma_stop);
/**
* ata_bmdma_status - Read PCI IDE BMDMA status
@@ -2330,6 +2425,7 @@ u8 ata_bmdma_status(struct ata_port *ap)
{
return ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
}
+EXPORT_SYMBOL_GPL(ata_bmdma_status);
/**
* ata_bus_reset - reset host port and associated ATA channel
@@ -2422,6 +2518,7 @@ err_out:
DPRINTK("EXIT\n");
}
+EXPORT_SYMBOL_GPL(ata_bus_reset);
#ifdef CONFIG_PCI
@@ -2449,6 +2546,7 @@ int ata_pci_bmdma_clear_simplex(struct pci_dev *pdev)
return -EOPNOTSUPP;
return 0;
}
+EXPORT_SYMBOL_GPL(ata_pci_bmdma_clear_simplex);
/**
* ata_pci_bmdma_init - acquire PCI BMDMA resources and init ATA host
@@ -2501,11 +2599,12 @@ int ata_pci_bmdma_init(struct ata_host *host)
host->flags |= ATA_HOST_SIMPLEX;
ata_port_desc(ap, "bmdma 0x%llx",
- (unsigned long long)pci_resource_start(pdev, 4) + 8 * i);
+ (unsigned long long)pci_resource_start(pdev, 4) + 8 * i);
}
return 0;
}
+EXPORT_SYMBOL_GPL(ata_pci_bmdma_init);
static int ata_resources_present(struct pci_dev *pdev, int port)
{
@@ -2513,7 +2612,7 @@ static int ata_resources_present(struct pci_dev *pdev, int port)
/* Check the PCI resources for this channel are enabled */
port = port * 2;
- for (i = 0; i < 2; i ++) {
+ for (i = 0; i < 2; i++) {
if (pci_resource_start(pdev, port + i) == 0 ||
pci_resource_len(pdev, port + i) == 0)
return 0;
@@ -2598,6 +2697,7 @@ int ata_pci_sff_init_host(struct ata_host *host)
return 0;
}
+EXPORT_SYMBOL_GPL(ata_pci_sff_init_host);
/**
* ata_pci_sff_prepare_host - helper to prepare native PCI ATA host
@@ -2615,7 +2715,7 @@ int ata_pci_sff_init_host(struct ata_host *host)
* 0 on success, -errno otherwise.
*/
int ata_pci_sff_prepare_host(struct pci_dev *pdev,
- const struct ata_port_info * const * ppi,
+ const struct ata_port_info * const *ppi,
struct ata_host **r_host)
{
struct ata_host *host;
@@ -2645,17 +2745,18 @@ int ata_pci_sff_prepare_host(struct pci_dev *pdev,
*r_host = host;
return 0;
- err_bmdma:
+err_bmdma:
/* This is necessary because PCI and iomap resources are
* merged and releasing the top group won't release the
* acquired resources if some of those have been acquired
* before entering this function.
*/
pcim_iounmap_regions(pdev, 0xf);
- err_out:
+err_out:
devres_release_group(&pdev->dev, NULL);
return rc;
}
+EXPORT_SYMBOL_GPL(ata_pci_sff_prepare_host);
/**
* ata_pci_sff_activate_host - start SFF host, request IRQ and register it
@@ -2741,7 +2842,7 @@ int ata_pci_sff_activate_host(struct ata_host *host,
}
rc = ata_host_register(host, sht);
- out:
+out:
if (rc == 0)
devres_remove_group(dev, NULL);
else
@@ -2749,6 +2850,7 @@ int ata_pci_sff_activate_host(struct ata_host *host,
return rc;
}
+EXPORT_SYMBOL_GPL(ata_pci_sff_activate_host);
/**
* ata_pci_sff_init_one - Initialize/register PCI IDE host controller
@@ -2776,7 +2878,7 @@ int ata_pci_sff_activate_host(struct ata_host *host,
* Zero on success, negative on errno-based value on error.
*/
int ata_pci_sff_init_one(struct pci_dev *pdev,
- const struct ata_port_info * const * ppi,
+ const struct ata_port_info * const *ppi,
struct scsi_host_template *sht, void *host_priv)
{
struct device *dev = &pdev->dev;
@@ -2815,7 +2917,7 @@ int ata_pci_sff_init_one(struct pci_dev *pdev,
pci_set_master(pdev);
rc = ata_pci_sff_activate_host(host, ata_sff_interrupt, sht);
- out:
+out:
if (rc == 0)
devres_remove_group(&pdev->dev, NULL);
else
@@ -2823,54 +2925,7 @@ int ata_pci_sff_init_one(struct pci_dev *pdev,
return rc;
}
+EXPORT_SYMBOL_GPL(ata_pci_sff_init_one);
#endif /* CONFIG_PCI */
-EXPORT_SYMBOL_GPL(ata_sff_port_ops);
-EXPORT_SYMBOL_GPL(ata_bmdma_port_ops);
-EXPORT_SYMBOL_GPL(ata_sff_qc_prep);
-EXPORT_SYMBOL_GPL(ata_sff_dumb_qc_prep);
-EXPORT_SYMBOL_GPL(ata_sff_dev_select);
-EXPORT_SYMBOL_GPL(ata_sff_check_status);
-EXPORT_SYMBOL_GPL(ata_sff_dma_pause);
-EXPORT_SYMBOL_GPL(ata_sff_pause);
-EXPORT_SYMBOL_GPL(ata_sff_busy_sleep);
-EXPORT_SYMBOL_GPL(ata_sff_wait_ready);
-EXPORT_SYMBOL_GPL(ata_sff_tf_load);
-EXPORT_SYMBOL_GPL(ata_sff_tf_read);
-EXPORT_SYMBOL_GPL(ata_sff_exec_command);
-EXPORT_SYMBOL_GPL(ata_sff_data_xfer);
-EXPORT_SYMBOL_GPL(ata_sff_data_xfer_noirq);
-EXPORT_SYMBOL_GPL(ata_sff_irq_on);
-EXPORT_SYMBOL_GPL(ata_sff_irq_clear);
-EXPORT_SYMBOL_GPL(ata_sff_hsm_move);
-EXPORT_SYMBOL_GPL(ata_sff_qc_issue);
-EXPORT_SYMBOL_GPL(ata_sff_qc_fill_rtf);
-EXPORT_SYMBOL_GPL(ata_sff_host_intr);
-EXPORT_SYMBOL_GPL(ata_sff_interrupt);
-EXPORT_SYMBOL_GPL(ata_sff_freeze);
-EXPORT_SYMBOL_GPL(ata_sff_thaw);
-EXPORT_SYMBOL_GPL(ata_sff_prereset);
-EXPORT_SYMBOL_GPL(ata_sff_dev_classify);
-EXPORT_SYMBOL_GPL(ata_sff_wait_after_reset);
-EXPORT_SYMBOL_GPL(ata_sff_softreset);
-EXPORT_SYMBOL_GPL(sata_sff_hardreset);
-EXPORT_SYMBOL_GPL(ata_sff_postreset);
-EXPORT_SYMBOL_GPL(ata_sff_error_handler);
-EXPORT_SYMBOL_GPL(ata_sff_post_internal_cmd);
-EXPORT_SYMBOL_GPL(ata_sff_port_start);
-EXPORT_SYMBOL_GPL(ata_sff_std_ports);
-EXPORT_SYMBOL_GPL(ata_bmdma_mode_filter);
-EXPORT_SYMBOL_GPL(ata_bmdma_setup);
-EXPORT_SYMBOL_GPL(ata_bmdma_start);
-EXPORT_SYMBOL_GPL(ata_bmdma_stop);
-EXPORT_SYMBOL_GPL(ata_bmdma_status);
-EXPORT_SYMBOL_GPL(ata_bus_reset);
-#ifdef CONFIG_PCI
-EXPORT_SYMBOL_GPL(ata_pci_bmdma_clear_simplex);
-EXPORT_SYMBOL_GPL(ata_pci_bmdma_init);
-EXPORT_SYMBOL_GPL(ata_pci_sff_init_host);
-EXPORT_SYMBOL_GPL(ata_pci_sff_prepare_host);
-EXPORT_SYMBOL_GPL(ata_pci_sff_activate_host);
-EXPORT_SYMBOL_GPL(ata_pci_sff_init_one);
-#endif /* CONFIG_PCI */
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index 73c466e..a7999c1 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -19,7 +19,9 @@
*
* TODO/CHECK
* Cannot have ATAPI on both master & slave for rev < c2 (???) but
- * otherwise should do atapi DMA.
+ * otherwise should do atapi DMA (For now for old we do PIO only for
+ * ATAPI)
+ * Review Sunblade workaround.
*/
#include <linux/kernel.h>
@@ -33,12 +35,14 @@
#include <linux/dmi.h>
#define DRV_NAME "pata_ali"
-#define DRV_VERSION "0.7.5"
+#define DRV_VERSION "0.7.8"
static int ali_atapi_dma = 0;
module_param_named(atapi_dma, ali_atapi_dma, int, 0644);
MODULE_PARM_DESC(atapi_dma, "Enable ATAPI DMA (0=disable, 1=enable)");
+static struct pci_dev *isa_bridge;
+
/*
* Cable special cases
*/
@@ -147,8 +151,7 @@ static void ali_fifo_control(struct ata_port *ap, struct ata_device *adev, int o
pci_read_config_byte(pdev, pio_fifo, &fifo);
fifo &= ~(0x0F << shift);
- if (on)
- fifo |= (on << shift);
+ fifo |= (on << shift);
pci_write_config_byte(pdev, pio_fifo, fifo);
}
@@ -337,6 +340,23 @@ static int ali_check_atapi_dma(struct ata_queued_cmd *qc)
return 0;
}
+static void ali_c2_c3_postreset(struct ata_link *link, unsigned int *classes)
+{
+ u8 r;
+ int port_bit = 4 << link->ap->port_no;
+
+ /* If our bridge is an ALI 1533 then do the extra work */
+ if (isa_bridge) {
+ /* Tristate and re-enable the bus signals */
+ pci_read_config_byte(isa_bridge, 0x58, &r);
+ r &= ~port_bit;
+ pci_write_config_byte(isa_bridge, 0x58, r);
+ r |= port_bit;
+ pci_write_config_byte(isa_bridge, 0x58, r);
+ }
+ ata_sff_postreset(link, classes);
+}
+
static struct scsi_host_template ali_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
@@ -349,10 +369,11 @@ static struct ata_port_operations ali_early_port_ops = {
.inherits = &ata_sff_port_ops,
.cable_detect = ata_cable_40wire,
.set_piomode = ali_set_piomode,
+ .sff_data_xfer = ata_sff_data_xfer32,
};
static const struct ata_port_operations ali_dma_base_ops = {
- .inherits = &ata_bmdma_port_ops,
+ .inherits = &ata_bmdma32_port_ops,
.set_piomode = ali_set_piomode,
.set_dmamode = ali_set_dmamode,
};
@@ -377,6 +398,17 @@ static struct ata_port_operations ali_c2_port_ops = {
.check_atapi_dma = ali_check_atapi_dma,
.cable_detect = ali_c2_cable_detect,
.dev_config = ali_lock_sectors,
+ .postreset = ali_c2_c3_postreset,
+};
+
+/*
+ * Port operations for DMA capable ALi with cable detect
+ */
+static struct ata_port_operations ali_c4_port_ops = {
+ .inherits = &ali_dma_base_ops,
+ .check_atapi_dma = ali_check_atapi_dma,
+ .cable_detect = ali_c2_cable_detect,
+ .dev_config = ali_lock_sectors,
};
/*
@@ -401,52 +433,49 @@ static struct ata_port_operations ali_c5_port_ops = {
static void ali_init_chipset(struct pci_dev *pdev)
{
u8 tmp;
- struct pci_dev *north, *isa_bridge;
+ struct pci_dev *north;
/*
* The chipset revision selects the driver operations and
* mode data.
*/
- if (pdev->revision >= 0x20 && pdev->revision < 0xC2) {
- /* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */
- pci_read_config_byte(pdev, 0x4B, &tmp);
- /* Clear CD-ROM DMA write bit */
- tmp &= 0x7F;
- pci_write_config_byte(pdev, 0x4B, tmp);
- } else if (pdev->revision >= 0xC2) {
- /* Enable cable detection logic */
+ if (pdev->revision <= 0x20) {
+ pci_read_config_byte(pdev, 0x53, &tmp);
+ tmp |= 0x03;
+ pci_write_config_byte(pdev, 0x53, tmp);
+ } else {
+ pci_read_config_byte(pdev, 0x4a, &tmp);
+ pci_write_config_byte(pdev, 0x4a, tmp | 0x20);
pci_read_config_byte(pdev, 0x4B, &tmp);
- pci_write_config_byte(pdev, 0x4B, tmp | 0x08);
- }
- north = pci_get_bus_and_slot(0, PCI_DEVFN(0,0));
- isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
-
- if (north && north->vendor == PCI_VENDOR_ID_AL && isa_bridge) {
- /* Configure the ALi bridge logic. For non ALi rely on BIOS.
- Set the south bridge enable bit */
- pci_read_config_byte(isa_bridge, 0x79, &tmp);
- if (pdev->revision == 0xC2)
- pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04);
- else if (pdev->revision > 0xC2 && pdev->revision < 0xC5)
- pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02);
- }
- if (pdev->revision >= 0x20) {
+ if (pdev->revision < 0xC2)
+ /* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */
+ /* Clear CD-ROM DMA write bit */
+ tmp &= 0x7F;
+ /* Cable and UDMA */
+ pci_write_config_byte(pdev, 0x4B, tmp | 0x09);
/*
* CD_ROM DMA on (0x53 bit 0). Enable this even if we want
* to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control
* via 0x54/55.
*/
pci_read_config_byte(pdev, 0x53, &tmp);
- if (pdev->revision <= 0x20)
- tmp &= ~0x02;
if (pdev->revision >= 0xc7)
tmp |= 0x03;
else
tmp |= 0x01; /* CD_ROM enable for DMA */
pci_write_config_byte(pdev, 0x53, tmp);
}
- pci_dev_put(isa_bridge);
+ north = pci_get_bus_and_slot(0, PCI_DEVFN(0,0));
+ if (north && north->vendor == PCI_VENDOR_ID_AL && isa_bridge) {
+ /* Configure the ALi bridge logic. For non ALi rely on BIOS.
+ Set the south bridge enable bit */
+ pci_read_config_byte(isa_bridge, 0x79, &tmp);
+ if (pdev->revision == 0xC2)
+ pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04);
+ else if (pdev->revision > 0xC2 && pdev->revision < 0xC5)
+ pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02);
+ }
pci_dev_put(north);
ata_pci_bmdma_clear_simplex(pdev);
}
@@ -503,7 +532,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = ATA_UDMA5,
- .port_ops = &ali_c2_port_ops
+ .port_ops = &ali_c4_port_ops
};
/* Revision 0xC5 is UDMA133 with LBA48 DMA */
static const struct ata_port_info info_c5 = {
@@ -516,7 +545,6 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
const struct ata_port_info *ppi[] = { NULL, NULL };
u8 tmp;
- struct pci_dev *isa_bridge;
int rc;
rc = pcim_enable_device(pdev);
@@ -543,14 +571,12 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
ali_init_chipset(pdev);
- isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
if (isa_bridge && pdev->revision >= 0x20 && pdev->revision < 0xC2) {
/* Are we paired with a UDMA capable chip */
pci_read_config_byte(isa_bridge, 0x5E, &tmp);
if ((tmp & 0x1E) == 0x12)
ppi[0] = &info_20_udma;
}
- pci_dev_put(isa_bridge);
return ata_pci_sff_init_one(pdev, ppi, &ali_sht, NULL);
}
@@ -590,13 +616,20 @@ static struct pci_driver ali_pci_driver = {
static int __init ali_init(void)
{
- return pci_register_driver(&ali_pci_driver);
+ int ret;
+ isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
+
+ ret = pci_register_driver(&ali_pci_driver);
+ if (ret < 0)
+ pci_dev_put(isa_bridge);
+ return ret;
}
static void __exit ali_exit(void)
{
pci_unregister_driver(&ali_pci_driver);
+ pci_dev_put(isa_bridge);
}
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index 0ec9c7d..63719ab 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -24,7 +24,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_amd"
-#define DRV_VERSION "0.3.10"
+#define DRV_VERSION "0.3.11"
/**
* timing_setup - shared timing computation and load
@@ -345,7 +345,7 @@ static struct scsi_host_template amd_sht = {
};
static const struct ata_port_operations amd_base_port_ops = {
- .inherits = &ata_bmdma_port_ops,
+ .inherits = &ata_bmdma32_port_ops,
.prereset = amd_pre_reset,
};
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index e0c4f05..65c28e5 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -30,7 +30,7 @@
#define DRV_VERSION "0.6.2"
struct hpt_clock {
- u8 xfer_speed;
+ u8 xfer_mode;
u32 timing;
};
@@ -189,28 +189,6 @@ static unsigned long hpt366_filter(struct ata_device *adev, unsigned long mask)
return ata_bmdma_mode_filter(adev, mask);
}
-/**
- * hpt36x_find_mode - reset the hpt36x bus
- * @ap: ATA port
- * @speed: transfer mode
- *
- * Return the 32bit register programming information for this channel
- * that matches the speed provided.
- */
-
-static u32 hpt36x_find_mode(struct ata_port *ap, int speed)
-{
- struct hpt_clock *clocks = ap->host->private_data;
-
- while(clocks->xfer_speed) {
- if (clocks->xfer_speed == speed)
- return clocks->timing;
- clocks++;
- }
- BUG();
- return 0xffffffffU; /* silence compiler warning */
-}
-
static int hpt36x_cable_detect(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
@@ -226,25 +204,16 @@ static int hpt36x_cable_detect(struct ata_port *ap)
return ATA_CBL_PATA80;
}
-/**
- * hpt366_set_piomode - PIO setup
- * @ap: ATA interface
- * @adev: device on the interface
- *
- * Perform PIO mode setup.
- */
-
-static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt366_set_mode(struct ata_port *ap, struct ata_device *adev,
+ u8 mode)
{
+ struct hpt_clock *clocks = ap->host->private_data;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg;
- u32 mode;
+ u32 addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+ u32 addr2 = 0x51 + 4 * ap->port_no;
+ u32 mask, reg;
u8 fast;
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
/* Fast interrupt prediction disable, hold off interrupt disable */
pci_read_config_byte(pdev, addr2, &fast);
if (fast & 0x80) {
@@ -252,12 +221,43 @@ static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
pci_write_config_byte(pdev, addr2, fast);
}
+ /* determine timing mask and find matching clock entry */
+ if (mode < XFER_MW_DMA_0)
+ mask = 0xc1f8ffff;
+ else if (mode < XFER_UDMA_0)
+ mask = 0x303800ff;
+ else
+ mask = 0x30070000;
+
+ while (clocks->xfer_mode) {
+ if (clocks->xfer_mode == mode)
+ break;
+ clocks++;
+ }
+ if (!clocks->xfer_mode)
+ BUG();
+
+ /*
+ * Combine new mode bits with old config bits and disable
+ * on-chip PIO FIFO/buffer (and PIO MST mode as well) to avoid
+ * problems handling I/O errors later.
+ */
pci_read_config_dword(pdev, addr1, ®);
- mode = hpt36x_find_mode(ap, adev->pio_mode);
- mode &= ~0x8000000; /* No FIFO in PIO */
- mode &= ~0x30070000; /* Leave config bits alone */
- reg &= 0x30070000; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+ reg = ((reg & ~mask) | (clocks->timing & mask)) & ~0xc0000000;
+ pci_write_config_dword(pdev, addr1, reg);
+}
+
+/**
+ * hpt366_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Perform PIO mode setup.
+ */
+
+static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ hpt366_set_mode(ap, adev, adev->pio_mode);
}
/**
@@ -271,28 +271,7 @@ static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
static void hpt366_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg;
- u32 mode;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- if (fast & 0x80) {
- fast &= ~0x80;
- pci_write_config_byte(pdev, addr2, fast);
- }
-
- pci_read_config_dword(pdev, addr1, ®);
- mode = hpt36x_find_mode(ap, adev->dma_mode);
- mode |= 0x8000000; /* FIFO in MWDMA or UDMA */
- mode &= ~0xC0000000; /* Leave config bits alone */
- reg &= 0xC0000000; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt366_set_mode(ap, adev, adev->dma_mode);
}
static struct scsi_host_template hpt36x_sht = {
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
index f11a320..f19cc64 100644
--- a/drivers/ata/pata_hpt3x3.c
+++ b/drivers/ata/pata_hpt3x3.c
@@ -23,7 +23,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x3"
-#define DRV_VERSION "0.5.3"
+#define DRV_VERSION "0.6.1"
/**
* hpt3x3_set_piomode - PIO setup
@@ -80,14 +80,48 @@ static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev)
r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */
if (adev->dma_mode >= XFER_UDMA_0)
- r2 |= (0x10 << dn); /* Ultra mode */
+ r2 |= (0x01 << dn); /* Ultra mode */
else
- r2 |= (0x01 << dn); /* MWDMA */
+ r2 |= (0x10 << dn); /* MWDMA */
pci_write_config_dword(pdev, 0x44, r1);
pci_write_config_dword(pdev, 0x48, r2);
}
-#endif /* CONFIG_PATA_HPT3X3_DMA */
+
+/**
+ * hpt3x3_freeze - DMA workaround
+ * @ap: port to freeze
+ *
+ * When freezing an HPT3x3 we must stop any pending DMA before
+ * writing to the control register or the chip will hang
+ */
+
+static void hpt3x3_freeze(struct ata_port *ap)
+{
+ void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+ iowrite8(ioread8(mmio + ATA_DMA_CMD) & ~ ATA_DMA_START,
+ mmio + ATA_DMA_CMD);
+ ata_sff_dma_pause(ap);
+ ata_sff_freeze(ap);
+}
+
+/**
+ * hpt3x3_bmdma_setup - DMA workaround
+ * @qc: Queued command
+ *
+ * When issuing BMDMA we must clean up the error/active bits in
+ * software on this device
+ */
+
+static void hpt3x3_bmdma_setup(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ u8 r = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+ r |= ATA_DMA_INTR | ATA_DMA_ERR;
+ iowrite8(r, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+ return ata_bmdma_setup(qc);
+}
/**
* hpt3x3_atapi_dma - ATAPI DMA check
@@ -101,18 +135,23 @@ static int hpt3x3_atapi_dma(struct ata_queued_cmd *qc)
return 1;
}
+#endif /* CONFIG_PATA_HPT3X3_DMA */
+
static struct scsi_host_template hpt3x3_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
static struct ata_port_operations hpt3x3_port_ops = {
.inherits = &ata_bmdma_port_ops,
- .check_atapi_dma= hpt3x3_atapi_dma,
.cable_detect = ata_cable_40wire,
.set_piomode = hpt3x3_set_piomode,
#if defined(CONFIG_PATA_HPT3X3_DMA)
.set_dmamode = hpt3x3_set_dmamode,
+ .bmdma_setup = hpt3x3_bmdma_setup,
+ .check_atapi_dma= hpt3x3_atapi_dma,
+ .freeze = hpt3x3_freeze,
#endif
+
};
/**
diff --git a/drivers/ata/pata_mpiix.c b/drivers/ata/pata_mpiix.c
index 7c8faa4..aa576ca 100644
--- a/drivers/ata/pata_mpiix.c
+++ b/drivers/ata/pata_mpiix.c
@@ -35,7 +35,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_mpiix"
-#define DRV_VERSION "0.7.6"
+#define DRV_VERSION "0.7.7"
enum {
IDETIM = 0x6C, /* IDE control register */
@@ -146,6 +146,7 @@ static struct ata_port_operations mpiix_port_ops = {
.cable_detect = ata_cable_40wire,
.set_piomode = mpiix_set_piomode,
.prereset = mpiix_pre_reset,
+ .sff_data_xfer = ata_sff_data_xfer32,
};
static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id)
diff --git a/drivers/ata/pata_platform.c b/drivers/ata/pata_platform.c
index 6afa07a..d8d743a 100644
--- a/drivers/ata/pata_platform.c
+++ b/drivers/ata/pata_platform.c
@@ -186,7 +186,7 @@ EXPORT_SYMBOL_GPL(__pata_platform_probe);
* A platform bus ATA device has been unplugged. Perform the needed
* cleanup. Also called on module unload for any active devices.
*/
-int __devexit __pata_platform_remove(struct device *dev)
+int __pata_platform_remove(struct device *dev)
{
struct ata_host *host = dev_get_drvdata(dev);
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index 83580a5..9e764e5 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -32,7 +32,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_sil680"
-#define DRV_VERSION "0.4.8"
+#define DRV_VERSION "0.4.9"
#define SIL680_MMIO_BAR 5
@@ -195,7 +195,7 @@ static struct scsi_host_template sil680_sht = {
};
static struct ata_port_operations sil680_port_ops = {
- .inherits = &ata_bmdma_port_ops,
+ .inherits = &ata_bmdma32_port_ops,
.cable_detect = sil680_cable_detect,
.set_piomode = sil680_set_piomode,
.set_dmamode = sil680_set_dmamode,
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index ccee930..2590c22 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -51,13 +51,6 @@ struct sil24_sge {
__le32 flags;
};
-/*
- * Port multiplier
- */
-struct sil24_port_multiplier {
- __le32 diag;
- __le32 sactive;
-};
enum {
SIL24_HOST_BAR = 0,
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 3449de5..4f7c8fb 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1518,6 +1518,7 @@ extern void sata_pmp_error_handler(struct ata_port *ap);
extern const struct ata_port_operations ata_sff_port_ops;
extern const struct ata_port_operations ata_bmdma_port_ops;
+extern const struct ata_port_operations ata_bmdma32_port_ops;
/* PIO only, sg_tablesize and dma_boundary limits can be removed */
#define ATA_PIO_SHT(drv_name) \
@@ -1545,6 +1546,8 @@ extern void ata_sff_exec_command(struct ata_port *ap,
const struct ata_taskfile *tf);
extern unsigned int ata_sff_data_xfer(struct ata_device *dev,
unsigned char *buf, unsigned int buflen, int rw);
+extern unsigned int ata_sff_data_xfer32(struct ata_device *dev,
+ unsigned char *buf, unsigned int buflen, int rw);
extern unsigned int ata_sff_data_xfer_noirq(struct ata_device *dev,
unsigned char *buf, unsigned int buflen, int rw);
extern u8 ata_sff_irq_on(struct ata_port *ap);
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2008-10-28 4:45 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2008-10-28 4:45 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
All bug fixes except for the one-line Promise PCI ID addition to ahci,
the zap-magic-numbers prep patch from David Milburn, and Alan's email
addr patch.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/ahci.c | 41 +++++++++++++++++++++++++----------
drivers/ata/ata_generic.c | 2 +-
drivers/ata/ata_piix.c | 2 +-
drivers/ata/libata-core.c | 35 +++++++++++++++++-------------
drivers/ata/libata-eh.c | 14 +++++++++++-
drivers/ata/pata_acpi.c | 2 +-
drivers/ata/pata_ali.c | 1 -
drivers/ata/pata_amd.c | 1 -
drivers/ata/pata_artop.c | 2 +-
drivers/ata/pata_atiixp.c | 1 -
drivers/ata/pata_cmd640.c | 1 -
drivers/ata/pata_cmd64x.c | 2 +-
drivers/ata/pata_cs5530.c | 1 -
drivers/ata/pata_cs5535.c | 2 +-
drivers/ata/pata_cypress.c | 2 +-
drivers/ata/pata_efar.c | 2 +-
drivers/ata/pata_isapnp.c | 2 +-
drivers/ata/pata_it821x.c | 7 ++---
drivers/ata/pata_jmicron.c | 2 +-
drivers/ata/pata_legacy.c | 2 +-
drivers/ata/pata_marvell.c | 2 +-
drivers/ata/pata_mpiix.c | 2 +-
drivers/ata/pata_netcell.c | 2 +-
drivers/ata/pata_ninja32.c | 44 ++++++++++++++++++++++++++++++--------
drivers/ata/pata_ns87410.c | 1 -
drivers/ata/pata_ns87415.c | 2 +-
drivers/ata/pata_oldpiix.c | 2 +-
drivers/ata/pata_opti.c | 1 -
drivers/ata/pata_optidma.c | 1 -
drivers/ata/pata_pcmcia.c | 2 +-
drivers/ata/pata_pdc202xx_old.c | 2 +-
drivers/ata/pata_platform.c | 2 +-
drivers/ata/pata_qdi.c | 2 +-
drivers/ata/pata_radisys.c | 2 +-
drivers/ata/pata_sc1200.c | 2 +-
drivers/ata/pata_scc.c | 2 +-
drivers/ata/pata_serverworks.c | 1 -
drivers/ata/pata_sil680.c | 1 -
drivers/ata/pata_sis.c | 2 +-
drivers/ata/pata_sl82c105.c | 1 -
drivers/ata/pata_triflex.c | 2 +-
drivers/ata/pata_via.c | 1 -
drivers/ata/pata_winbond.c | 2 +-
drivers/ata/sata_sil24.c | 5 ++++
44 files changed, 130 insertions(+), 80 deletions(-)
Alan Cox (2):
ata: Switch all my stuff to a common address
pata_ninja32: suspend/resume support
David Milburn (2):
libata: ahci enclosure management led sync
libata: ahci enclosure management bit mask
Mark Nelson (1):
ahci: Add support for Promise PDC42819
Ondrej Zary (1):
libata: Fix LBA48 on pata_it821x RAID volumes.
Randy Dunlap (1):
libata: add missing kernel-doc
Tejun Heo (3):
libata: fix device iteration bugs
sata_sil24: configure max read request size to 4k
libata: clear saved xfer_mode and ncq_enabled on device detach
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index aeadd00..a67b8e7 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -49,6 +49,17 @@
#define DRV_NAME "ahci"
#define DRV_VERSION "3.0"
+/* Enclosure Management Control */
+#define EM_CTRL_MSG_TYPE 0x000f0000
+
+/* Enclosure Management LED Message Type */
+#define EM_MSG_LED_HBA_PORT 0x0000000f
+#define EM_MSG_LED_PMP_SLOT 0x0000ff00
+#define EM_MSG_LED_VALUE 0xffff0000
+#define EM_MSG_LED_VALUE_ACTIVITY 0x00070000
+#define EM_MSG_LED_VALUE_OFF 0xfff80000
+#define EM_MSG_LED_VALUE_ON 0x00010000
+
static int ahci_skip_host_reset;
module_param_named(skip_host_reset, ahci_skip_host_reset, int, 0444);
MODULE_PARM_DESC(skip_host_reset, "skip global host reset (0=don't skip, 1=skip)");
@@ -588,6 +599,9 @@ static const struct pci_device_id ahci_pci_tbl[] = {
{ PCI_VDEVICE(MARVELL, 0x6145), board_ahci_mv }, /* 6145 */
{ PCI_VDEVICE(MARVELL, 0x6121), board_ahci_mv }, /* 6121 */
+ /* Promise */
+ { PCI_VDEVICE(PROMISE, 0x3f20), board_ahci }, /* PDC42819 */
+
/* Generic, PCI class code for AHCI */
{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_STORAGE_SATA_AHCI, 0xffffff, board_ahci },
@@ -1220,18 +1234,20 @@ static void ahci_sw_activity_blink(unsigned long arg)
struct ahci_em_priv *emp = &pp->em_priv[link->pmp];
unsigned long led_message = emp->led_state;
u32 activity_led_state;
+ unsigned long flags;
- led_message &= 0xffff0000;
+ led_message &= EM_MSG_LED_VALUE;
led_message |= ap->port_no | (link->pmp << 8);
/* check to see if we've had activity. If so,
* toggle state of LED and reset timer. If not,
* turn LED to desired idle state.
*/
+ spin_lock_irqsave(ap->lock, flags);
if (emp->saved_activity != emp->activity) {
emp->saved_activity = emp->activity;
/* get the current LED state */
- activity_led_state = led_message & 0x00010000;
+ activity_led_state = led_message & EM_MSG_LED_VALUE_ON;
if (activity_led_state)
activity_led_state = 0;
@@ -1239,17 +1255,18 @@ static void ahci_sw_activity_blink(unsigned long arg)
activity_led_state = 1;
/* clear old state */
- led_message &= 0xfff8ffff;
+ led_message &= ~EM_MSG_LED_VALUE_ACTIVITY;
/* toggle state */
led_message |= (activity_led_state << 16);
mod_timer(&emp->timer, jiffies + msecs_to_jiffies(100));
} else {
/* switch to idle */
- led_message &= 0xfff8ffff;
+ led_message &= ~EM_MSG_LED_VALUE_ACTIVITY;
if (emp->blink_policy == BLINK_OFF)
led_message |= (1 << 16);
}
+ spin_unlock_irqrestore(ap->lock, flags);
ahci_transmit_led_message(ap, led_message, 4);
}
@@ -1294,7 +1311,7 @@ static ssize_t ahci_transmit_led_message(struct ata_port *ap, u32 state,
struct ahci_em_priv *emp;
/* get the slot number from the message */
- pmp = (state & 0x0000ff00) >> 8;
+ pmp = (state & EM_MSG_LED_PMP_SLOT) >> 8;
if (pmp < MAX_SLOTS)
emp = &pp->em_priv[pmp];
else
@@ -1319,7 +1336,7 @@ static ssize_t ahci_transmit_led_message(struct ata_port *ap, u32 state,
message[0] |= (4 << 8);
/* ignore 0:4 of byte zero, fill in port info yourself */
- message[1] = ((state & 0xfffffff0) | ap->port_no);
+ message[1] = ((state & ~EM_MSG_LED_HBA_PORT) | ap->port_no);
/* write message to EM_LOC */
writel(message[0], mmio + hpriv->em_loc);
@@ -1362,7 +1379,7 @@ static ssize_t ahci_led_store(struct ata_port *ap, const char *buf,
state = simple_strtoul(buf, NULL, 0);
/* get the slot number from the message */
- pmp = (state & 0x0000ff00) >> 8;
+ pmp = (state & EM_MSG_LED_PMP_SLOT) >> 8;
if (pmp < MAX_SLOTS)
emp = &pp->em_priv[pmp];
else
@@ -1373,7 +1390,7 @@ static ssize_t ahci_led_store(struct ata_port *ap, const char *buf,
* activity led through em_message
*/
if (emp->blink_policy)
- state &= 0xfff8ffff;
+ state &= ~EM_MSG_LED_VALUE_ACTIVITY;
return ahci_transmit_led_message(ap, state, size);
}
@@ -1392,16 +1409,16 @@ static ssize_t ahci_activity_store(struct ata_device *dev, enum sw_activity val)
link->flags &= ~(ATA_LFLAG_SW_ACTIVITY);
/* set the LED to OFF */
- port_led_state &= 0xfff80000;
+ port_led_state &= EM_MSG_LED_VALUE_OFF;
port_led_state |= (ap->port_no | (link->pmp << 8));
ahci_transmit_led_message(ap, port_led_state, 4);
} else {
link->flags |= ATA_LFLAG_SW_ACTIVITY;
if (val == BLINK_OFF) {
/* set LED to ON for idle */
- port_led_state &= 0xfff80000;
+ port_led_state &= EM_MSG_LED_VALUE_OFF;
port_led_state |= (ap->port_no | (link->pmp << 8));
- port_led_state |= 0x00010000; /* check this */
+ port_led_state |= EM_MSG_LED_VALUE_ON; /* check this */
ahci_transmit_led_message(ap, port_led_state, 4);
}
}
@@ -2612,7 +2629,7 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
u32 em_loc = readl(mmio + HOST_EM_LOC);
u32 em_ctl = readl(mmio + HOST_EM_CTL);
- messages = (em_ctl & 0x000f0000) >> 16;
+ messages = (em_ctl & EM_CTRL_MSG_TYPE) >> 16;
/* we only support LED message type right now */
if ((messages & 0x01) && (ahci_em_messages == 1)) {
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
index 75a406f..5c33767 100644
--- a/drivers/ata/ata_generic.c
+++ b/drivers/ata/ata_generic.c
@@ -1,6 +1,6 @@
/*
* ata_generic.c - Generic PATA/SATA controller driver.
- * Copyright 2005 Red Hat Inc <alan@redhat.com>, all rights reserved.
+ * Copyright 2005 Red Hat Inc, all rights reserved.
*
* Elements from ide/pci/generic.c
* Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org>
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index e9e32ed..52dc2d8 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -14,7 +14,7 @@
*
* Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
- * Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
+ * Copyright (C) 2003 Red Hat Inc
*
*
* This program is free software; you can redistribute it and/or modify
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 8cb0b36..2ff633c 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -4156,29 +4156,33 @@ static int cable_is_40wire(struct ata_port *ap)
struct ata_link *link;
struct ata_device *dev;
- /* If the controller thinks we are 40 wire, we are */
+ /* If the controller thinks we are 40 wire, we are. */
if (ap->cbl == ATA_CBL_PATA40)
return 1;
- /* If the controller thinks we are 80 wire, we are */
+
+ /* If the controller thinks we are 80 wire, we are. */
if (ap->cbl == ATA_CBL_PATA80 || ap->cbl == ATA_CBL_SATA)
return 0;
- /* If the system is known to be 40 wire short cable (eg laptop),
- then we allow 80 wire modes even if the drive isn't sure */
+
+ /* If the system is known to be 40 wire short cable (eg
+ * laptop), then we allow 80 wire modes even if the drive
+ * isn't sure.
+ */
if (ap->cbl == ATA_CBL_PATA40_SHORT)
return 0;
- /* If the controller doesn't know we scan
-
- - Note: We look for all 40 wire detects at this point.
- Any 80 wire detect is taken to be 80 wire cable
- because
- - In many setups only the one drive (slave if present)
- will give a valid detect
- - If you have a non detect capable drive you don't
- want it to colour the choice
- */
+
+ /* If the controller doesn't know, we scan.
+ *
+ * Note: We look for all 40 wire detects at this point. Any
+ * 80 wire detect is taken to be 80 wire cable because
+ * - in many setups only the one drive (slave if present) will
+ * give a valid detect
+ * - if you have a non detect capable drive you don't want it
+ * to colour the choice
+ */
ata_port_for_each_link(link, ap) {
ata_link_for_each_dev(dev, link) {
- if (!ata_is_40wire(dev))
+ if (ata_dev_enabled(dev) && !ata_is_40wire(dev))
return 0;
}
}
@@ -4553,6 +4557,7 @@ void swap_buf_le16(u16 *buf, unsigned int buf_words)
/**
* ata_qc_new_init - Request an available ATA command, and initialize it
* @dev: Device from whom we request an available command structure
+ * @tag: command tag
*
* LOCKING:
* None.
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 5d687d7..8077bdf 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -603,6 +603,9 @@ void ata_scsi_error(struct Scsi_Host *host)
ata_link_for_each_dev(dev, link) {
int devno = dev->devno;
+ if (!ata_dev_enabled(dev))
+ continue;
+
ehc->saved_xfer_mode[devno] = dev->xfer_mode;
if (ata_ncq_enabled(dev))
ehc->saved_ncq_enabled |= 1 << devno;
@@ -1161,6 +1164,7 @@ void ata_eh_detach_dev(struct ata_device *dev)
{
struct ata_link *link = dev->link;
struct ata_port *ap = link->ap;
+ struct ata_eh_context *ehc = &link->eh_context;
unsigned long flags;
ata_dev_disable(dev);
@@ -1174,9 +1178,11 @@ void ata_eh_detach_dev(struct ata_device *dev)
ap->pflags |= ATA_PFLAG_SCSI_HOTPLUG;
}
- /* clear per-dev EH actions */
+ /* clear per-dev EH info */
ata_eh_clear_action(link, dev, &link->eh_info, ATA_EH_PERDEV_MASK);
ata_eh_clear_action(link, dev, &link->eh_context.i, ATA_EH_PERDEV_MASK);
+ ehc->saved_xfer_mode[dev->devno] = 0;
+ ehc->saved_ncq_enabled &= ~(1 << dev->devno);
spin_unlock_irqrestore(ap->lock, flags);
}
@@ -2787,6 +2793,9 @@ int ata_set_mode(struct ata_link *link, struct ata_device **r_failed_dev)
/* if data transfer is verified, clear DUBIOUS_XFER on ering top */
ata_link_for_each_dev(dev, link) {
+ if (!ata_dev_enabled(dev))
+ continue;
+
if (!(dev->flags & ATA_DFLAG_DUBIOUS_XFER)) {
struct ata_ering_entry *ent;
@@ -2808,6 +2817,9 @@ int ata_set_mode(struct ata_link *link, struct ata_device **r_failed_dev)
u8 saved_xfer_mode = ehc->saved_xfer_mode[dev->devno];
u8 saved_ncq = !!(ehc->saved_ncq_enabled & (1 << dev->devno));
+ if (!ata_dev_enabled(dev))
+ continue;
+
if (dev->xfer_mode != saved_xfer_mode ||
ata_ncq_enabled(dev) != saved_ncq)
dev->flags |= ATA_DFLAG_DUBIOUS_XFER;
diff --git a/drivers/ata/pata_acpi.c b/drivers/ata/pata_acpi.c
index eb919c1..e2e332d 100644
--- a/drivers/ata/pata_acpi.c
+++ b/drivers/ata/pata_acpi.c
@@ -1,7 +1,7 @@
/*
* ACPI PATA driver
*
- * (c) 2007 Red Hat <alan@redhat.com>
+ * (c) 2007 Red Hat
*/
#include <linux/kernel.h>
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index 5ca70fa..73c466e 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -1,7 +1,6 @@
/*
* pata_ali.c - ALI 15x3 PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* based in part upon
* linux/drivers/ide/pci/alim15x3.c Version 0.17 2003/01/02
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index 57dd00f..0ec9c7d 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -1,7 +1,6 @@
/*
* pata_amd.c - AMD PATA for new ATA layer
* (C) 2005-2006 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* Based on pata-sil680. Errata information is taken from data sheets
* and the amd74xx.c driver by Vojtech Pavlik. Nvidia SATA devices are
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
index 0f513bc..6b3092c 100644
--- a/drivers/ata/pata_artop.c
+++ b/drivers/ata/pata_artop.c
@@ -1,7 +1,7 @@
/*
* pata_artop.c - ARTOP ATA controller driver
*
- * (C) 2006 Red Hat <alan@redhat.com>
+ * (C) 2006 Red Hat
* (C) 2007 Bartlomiej Zolnierkiewicz
*
* Based in part on drivers/ide/pci/aec62xx.c
diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
index e8a0d99..0e2cde8 100644
--- a/drivers/ata/pata_atiixp.c
+++ b/drivers/ata/pata_atiixp.c
@@ -1,7 +1,6 @@
/*
* pata_atiixp.c - ATI PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* Based on
*
diff --git a/drivers/ata/pata_cmd640.c b/drivers/ata/pata_cmd640.c
index 2de30b9..34a3942 100644
--- a/drivers/ata/pata_cmd640.c
+++ b/drivers/ata/pata_cmd640.c
@@ -1,7 +1,6 @@
/*
* pata_cmd640.c - CMD640 PCI PATA for new ATA layer
* (C) 2007 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* Based upon
* linux/drivers/ide/pci/cmd640.c Version 1.02 Sep 01, 1996
diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c
index ddd09b7..3167d8f 100644
--- a/drivers/ata/pata_cmd64x.c
+++ b/drivers/ata/pata_cmd64x.c
@@ -1,7 +1,7 @@
/*
* pata_cmd64x.c - CMD64x PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
+ * Alan Cox <alan@lxorguk.ukuu.org.uk>
*
* Based upon
* linux/drivers/ide/pci/cmd64x.c Version 1.30 Sept 10, 2002
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
index 0c4b271..bba4533 100644
--- a/drivers/ata/pata_cs5530.c
+++ b/drivers/ata/pata_cs5530.c
@@ -1,7 +1,6 @@
/*
* pata-cs5530.c - CS5530 PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* based upon cs5530.c by Mark Lord.
*
diff --git a/drivers/ata/pata_cs5535.c b/drivers/ata/pata_cs5535.c
index f1b6556..1b2d4a0 100644
--- a/drivers/ata/pata_cs5535.c
+++ b/drivers/ata/pata_cs5535.c
@@ -1,7 +1,7 @@
/*
* pata-cs5535.c - CS5535 PATA for new ATA layer
* (C) 2005-2006 Red Hat Inc
- * Alan Cox <alan@redhat.com>
+ * Alan Cox <alan@lxorguk.ukuu.org.uk>
*
* based upon cs5535.c from AMD <Jens.Altmann@amd.com> as cleaned up and
* made readable and Linux style by Wolfgang Zuleger <wolfgang.zuleger@gmx.de
diff --git a/drivers/ata/pata_cypress.c b/drivers/ata/pata_cypress.c
index 2ff6260..d546425 100644
--- a/drivers/ata/pata_cypress.c
+++ b/drivers/ata/pata_cypress.c
@@ -1,7 +1,7 @@
/*
* pata_cypress.c - Cypress PATA for new ATA layer
* (C) 2006 Red Hat Inc
- * Alan Cox <alan@redhat.com>
+ * Alan Cox
*
* Based heavily on
* linux/drivers/ide/pci/cy82c693.c Version 0.40 Sep. 10, 2002
diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c
index 9fba829..ac6392e 100644
--- a/drivers/ata/pata_efar.c
+++ b/drivers/ata/pata_efar.c
@@ -1,7 +1,7 @@
/*
* pata_efar.c - EFAR PIIX clone controller driver
*
- * (C) 2005 Red Hat <alan@redhat.com>
+ * (C) 2005 Red Hat
*
* Some parts based on ata_piix.c by Jeff Garzik and others.
*
diff --git a/drivers/ata/pata_isapnp.c b/drivers/ata/pata_isapnp.c
index 6a111ba..15cdb91 100644
--- a/drivers/ata/pata_isapnp.c
+++ b/drivers/ata/pata_isapnp.c
@@ -1,7 +1,7 @@
/*
* pata-isapnp.c - ISA PnP PATA controller driver.
- * Copyright 2005/2006 Red Hat Inc <alan@redhat.com>, all rights reserved.
+ * Copyright 2005/2006 Red Hat Inc, all rights reserved.
*
* Based in part on ide-pnp.c by Andrey Panin <pazke@donpac.ru>
*/
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
index 0221c9a..860ede5 100644
--- a/drivers/ata/pata_it821x.c
+++ b/drivers/ata/pata_it821x.c
@@ -1,7 +1,7 @@
/*
* pata_it821x.c - IT821x PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
+ * Alan Cox <alan@lxorguk.ukuu.org.uk>
* (C) 2007 Bartlomiej Zolnierkiewicz
*
* based upon
@@ -10,7 +10,7 @@
*
* linux/drivers/ide/pci/it821x.c Version 0.09 December 2004
*
- * Copyright (C) 2004 Red Hat <alan@redhat.com>
+ * Copyright (C) 2004 Red Hat
*
* May be copied or modified under the terms of the GNU General Public License
* Based in part on the ITE vendor provided SCSI driver.
@@ -557,9 +557,8 @@ static unsigned int it821x_read_id(struct ata_device *adev,
if (strstr(model_num, "Integrated Technology Express")) {
/* Set feature bits the firmware neglects */
id[49] |= 0x0300; /* LBA, DMA */
- id[82] |= 0x0400; /* LBA48 */
id[83] &= 0x7FFF;
- id[83] |= 0x4000; /* Word 83 is valid */
+ id[83] |= 0x4400; /* Word 83 is valid and LBA48 */
id[86] |= 0x0400; /* LBA48 on */
id[ATA_ID_MAJOR_VER] |= 0x1F;
}
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
index 73b7596..38cf1ab 100644
--- a/drivers/ata/pata_jmicron.c
+++ b/drivers/ata/pata_jmicron.c
@@ -4,7 +4,7 @@
* driven by AHCI in the usual configuration although
* this driver can handle other setups if we need it.
*
- * (c) 2006 Red Hat <alan@redhat.com>
+ * (c) 2006 Red Hat
*/
#include <linux/kernel.h>
diff --git a/drivers/ata/pata_legacy.c b/drivers/ata/pata_legacy.c
index bc037ff..930c220 100644
--- a/drivers/ata/pata_legacy.c
+++ b/drivers/ata/pata_legacy.c
@@ -1,6 +1,6 @@
/*
* pata-legacy.c - Legacy port PATA/SATA controller driver.
- * Copyright 2005/2006 Red Hat <alan@redhat.com>, all rights reserved.
+ * Copyright 2005/2006 Red Hat, all rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
diff --git a/drivers/ata/pata_marvell.c b/drivers/ata/pata_marvell.c
index 0d87eec..76e399b 100644
--- a/drivers/ata/pata_marvell.c
+++ b/drivers/ata/pata_marvell.c
@@ -5,7 +5,7 @@
* isn't making full use of the device functionality but it is
* easy to get working.
*
- * (c) 2006 Red Hat <alan@redhat.com>
+ * (c) 2006 Red Hat
*/
#include <linux/kernel.h>
diff --git a/drivers/ata/pata_mpiix.c b/drivers/ata/pata_mpiix.c
index 7d7e3fd..7c8faa4 100644
--- a/drivers/ata/pata_mpiix.c
+++ b/drivers/ata/pata_mpiix.c
@@ -1,7 +1,7 @@
/*
* pata_mpiix.c - Intel MPIIX PATA for new ATA layer
* (C) 2005-2006 Red Hat Inc
- * Alan Cox <alan@redhat.com>
+ * Alan Cox <alan@lxorguk.ukuu.org.uk>
*
* The MPIIX is different enough to the PIIX4 and friends that we give it
* a separate driver. The old ide/pci code handles this by just not tuning
diff --git a/drivers/ata/pata_netcell.c b/drivers/ata/pata_netcell.c
index d9719c8..9dc05e1 100644
--- a/drivers/ata/pata_netcell.c
+++ b/drivers/ata/pata_netcell.c
@@ -1,7 +1,7 @@
/*
* pata_netcell.c - Netcell PATA driver
*
- * (c) 2006 Red Hat <alan@redhat.com>
+ * (c) 2006 Red Hat
*/
#include <linux/kernel.h>
diff --git a/drivers/ata/pata_ninja32.c b/drivers/ata/pata_ninja32.c
index 565e67c..4e466ea 100644
--- a/drivers/ata/pata_ninja32.c
+++ b/drivers/ata/pata_ninja32.c
@@ -1,7 +1,6 @@
/*
* pata_ninja32.c - Ninja32 PATA for new ATA layer
* (C) 2007 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* Note: The controller like many controllers has shared timings for
* PIO and DMA. We thus flip to the DMA timings in dma_start and flip back
@@ -45,7 +44,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_ninja32"
-#define DRV_VERSION "0.0.1"
+#define DRV_VERSION "0.1.1"
/**
@@ -89,6 +88,17 @@ static struct ata_port_operations ninja32_port_ops = {
.set_piomode = ninja32_set_piomode,
};
+static void ninja32_program(void __iomem *base)
+{
+ iowrite8(0x05, base + 0x01); /* Enable interrupt lines */
+ iowrite8(0xBE, base + 0x02); /* Burst, ?? setup */
+ iowrite8(0x01, base + 0x03); /* Unknown */
+ iowrite8(0x20, base + 0x04); /* WAIT0 */
+ iowrite8(0x8f, base + 0x05); /* Unknown */
+ iowrite8(0xa4, base + 0x1c); /* Unknown */
+ iowrite8(0x83, base + 0x1d); /* BMDMA control: WAIT0 */
+}
+
static int ninja32_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
struct ata_host *host;
@@ -134,18 +144,28 @@ static int ninja32_init_one(struct pci_dev *dev, const struct pci_device_id *id)
ap->ioaddr.bmdma_addr = base;
ata_sff_std_ports(&ap->ioaddr);
- iowrite8(0x05, base + 0x01); /* Enable interrupt lines */
- iowrite8(0xBE, base + 0x02); /* Burst, ?? setup */
- iowrite8(0x01, base + 0x03); /* Unknown */
- iowrite8(0x20, base + 0x04); /* WAIT0 */
- iowrite8(0x8f, base + 0x05); /* Unknown */
- iowrite8(0xa4, base + 0x1c); /* Unknown */
- iowrite8(0x83, base + 0x1d); /* BMDMA control: WAIT0 */
+ ninja32_program(base);
/* FIXME: Should we disable them at remove ? */
return ata_host_activate(host, dev->irq, ata_sff_interrupt,
IRQF_SHARED, &ninja32_sht);
}
+#ifdef CONFIG_PM
+
+static int ninja32_reinit_one(struct pci_dev *pdev)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ int rc;
+
+ rc = ata_pci_device_do_resume(pdev);
+ if (rc)
+ return rc;
+ ninja32_program(host->iomap[0]);
+ ata_host_resume(host);
+ return 0;
+}
+#endif
+
static const struct pci_device_id ninja32[] = {
{ 0x1145, 0xf021, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
{ 0x1145, 0xf024, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
@@ -156,7 +176,11 @@ static struct pci_driver ninja32_pci_driver = {
.name = DRV_NAME,
.id_table = ninja32,
.probe = ninja32_init_one,
- .remove = ata_pci_remove_one
+ .remove = ata_pci_remove_one,
+#ifdef CONFIG_PM
+ .suspend = ata_pci_device_suspend,
+ .resume = ninja32_reinit_one,
+#endif
};
static int __init ninja32_init(void)
diff --git a/drivers/ata/pata_ns87410.c b/drivers/ata/pata_ns87410.c
index be756b7..40d411c 100644
--- a/drivers/ata/pata_ns87410.c
+++ b/drivers/ata/pata_ns87410.c
@@ -1,7 +1,6 @@
/*
* pata_ns87410.c - National Semiconductor 87410 PATA for new ATA layer
* (C) 2006 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
diff --git a/drivers/ata/pata_ns87415.c b/drivers/ata/pata_ns87415.c
index e0aa7ea..89bf5f8 100644
--- a/drivers/ata/pata_ns87415.c
+++ b/drivers/ata/pata_ns87415.c
@@ -1,7 +1,7 @@
/*
* pata_ns87415.c - NS87415 (non PARISC) PATA
*
- * (C) 2005 Red Hat <alan@redhat.com>
+ * (C) 2005 Red Hat <alan@lxorguk.ukuu.org.uk>
*
* This is a fairly generic MWDMA controller. It has some limitations
* as it requires timing reloads on PIO/DMA transitions but it is otherwise
diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c
index df64f24..c0dbc46 100644
--- a/drivers/ata/pata_oldpiix.c
+++ b/drivers/ata/pata_oldpiix.c
@@ -1,7 +1,7 @@
/*
* pata_oldpiix.c - Intel PATA/SATA controllers
*
- * (C) 2005 Red Hat <alan@redhat.com>
+ * (C) 2005 Red Hat
*
* Some parts based on ata_piix.c by Jeff Garzik and others.
*
diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c
index fb2cf66..e4fa4d5 100644
--- a/drivers/ata/pata_opti.c
+++ b/drivers/ata/pata_opti.c
@@ -1,7 +1,6 @@
/*
* pata_opti.c - ATI PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* Based on
* linux/drivers/ide/pci/opti621.c Version 0.7 Sept 10, 2002
diff --git a/drivers/ata/pata_optidma.c b/drivers/ata/pata_optidma.c
index 4cd7444..93bb6e9 100644
--- a/drivers/ata/pata_optidma.c
+++ b/drivers/ata/pata_optidma.c
@@ -1,7 +1,6 @@
/*
* pata_optidma.c - Opti DMA PATA for new ATA layer
* (C) 2006 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* The Opti DMA controllers are related to the older PIO PCI controllers
* and indeed the VLB ones. The main differences are that the timing
diff --git a/drivers/ata/pata_pcmcia.c b/drivers/ata/pata_pcmcia.c
index 02b596b..271cb64 100644
--- a/drivers/ata/pata_pcmcia.c
+++ b/drivers/ata/pata_pcmcia.c
@@ -1,6 +1,6 @@
/*
* pata_pcmcia.c - PCMCIA PATA controller driver.
- * Copyright 2005-2006 Red Hat Inc <alan@redhat.com>, all rights reserved.
+ * Copyright 2005-2006 Red Hat Inc, all rights reserved.
* PCMCIA ident update Copyright 2006 Marcin Juszkiewicz
* <openembedded@hrw.one.pl>
*
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c
index d267306..799a6a0 100644
--- a/drivers/ata/pata_pdc202xx_old.c
+++ b/drivers/ata/pata_pdc202xx_old.c
@@ -1,7 +1,7 @@
/*
* pata_pdc202xx_old.c - Promise PDC202xx PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
+ * Alan Cox <alan@lxorguk.ukuu.org.uk>
* (C) 2007 Bartlomiej Zolnierkiewicz
*
* Based in part on linux/drivers/ide/pci/pdc202xx_old.c
diff --git a/drivers/ata/pata_platform.c b/drivers/ata/pata_platform.c
index 8f65ad6..77e4e3b 100644
--- a/drivers/ata/pata_platform.c
+++ b/drivers/ata/pata_platform.c
@@ -5,7 +5,7 @@
*
* Based on pata_pcmcia:
*
- * Copyright 2005-2006 Red Hat Inc <alan@redhat.com>, all rights reserved.
+ * Copyright 2005-2006 Red Hat Inc, all rights reserved.
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
diff --git a/drivers/ata/pata_qdi.c b/drivers/ata/pata_qdi.c
index 63b7a1c..3080f37 100644
--- a/drivers/ata/pata_qdi.c
+++ b/drivers/ata/pata_qdi.c
@@ -1,6 +1,6 @@
/*
* pata_qdi.c - QDI VLB ATA controllers
- * (C) 2006 Red Hat <alan@redhat.com>
+ * (C) 2006 Red Hat
*
* This driver mostly exists as a proof of concept for non PCI devices under
* libata. While the QDI6580 was 'neat' in 1993 it is no longer terribly
diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c
index 1c0d9fa..0b0aa45 100644
--- a/drivers/ata/pata_radisys.c
+++ b/drivers/ata/pata_radisys.c
@@ -1,7 +1,7 @@
/*
* pata_radisys.c - Intel PATA/SATA controllers
*
- * (C) 2006 Red Hat <alan@redhat.com>
+ * (C) 2006 Red Hat <alan@lxorguk.ukuu.org.uk>
*
* Some parts based on ata_piix.c by Jeff Garzik and others.
*
diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c
index 0278fd2..9a4bdca 100644
--- a/drivers/ata/pata_sc1200.c
+++ b/drivers/ata/pata_sc1200.c
@@ -1,5 +1,5 @@
/*
- * New ATA layer SC1200 driver Alan Cox <alan@redhat.com>
+ * New ATA layer SC1200 driver Alan Cox <alan@lxorguk.ukuu.org.uk>
*
* TODO: Mode selection filtering
* TODO: Can't enable second channel until ATA core has serialize
diff --git a/drivers/ata/pata_scc.c b/drivers/ata/pata_scc.c
index 16673d1..cf3707e 100644
--- a/drivers/ata/pata_scc.c
+++ b/drivers/ata/pata_scc.c
@@ -8,7 +8,7 @@
* Copyright 2003-2005 Jeff Garzik
* Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
- * Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
+ * Copyright (C) 2003 Red Hat Inc
*
* and drivers/ata/ahci.c:
* Copyright 2004-2005 Red Hat, Inc.
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c
index ffd26d0..72e41c9 100644
--- a/drivers/ata/pata_serverworks.c
+++ b/drivers/ata/pata_serverworks.c
@@ -1,7 +1,6 @@
/*
* pata_serverworks.c - Serverworks PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* based upon
*
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index a598bb3..83580a5 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -1,7 +1,6 @@
/*
* pata_sil680.c - SIL680 PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* based upon
*
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index 26345d7..d342366 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -1,7 +1,7 @@
/*
* pata_sis.c - SiS ATA driver
*
- * (C) 2005 Red Hat <alan@redhat.com>
+ * (C) 2005 Red Hat
* (C) 2007 Bartlomiej Zolnierkiewicz
*
* Based upon linux/drivers/ide/pci/sis5513.c
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index 69877bd..1b0e7b6 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -1,7 +1,6 @@
/*
* pata_sl82c105.c - SL82C105 PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* Based in part on linux/drivers/ide/pci/sl82c105.c
* SL82C105/Winbond 553 IDE driver
diff --git a/drivers/ata/pata_triflex.c b/drivers/ata/pata_triflex.c
index b181261..ef95975 100644
--- a/drivers/ata/pata_triflex.c
+++ b/drivers/ata/pata_triflex.c
@@ -1,7 +1,7 @@
/*
* pata_triflex.c - Compaq PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
+ * Alan Cox <alan@lxorguk.ukuu.org.uk>
*
* based upon
*
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 8fdb2ce..681169c 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -1,7 +1,6 @@
/*
* pata_via.c - VIA PATA for new ATA layer
* (C) 2005-2006 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* Documentation
* Most chipset documentation available under NDA only
diff --git a/drivers/ata/pata_winbond.c b/drivers/ata/pata_winbond.c
index a7606b0..319e164 100644
--- a/drivers/ata/pata_winbond.c
+++ b/drivers/ata/pata_winbond.c
@@ -1,6 +1,6 @@
/*
* pata_winbond.c - Winbond VLB ATA controllers
- * (C) 2006 Red Hat <alan@redhat.com>
+ * (C) 2006 Red Hat
*
* Support for the Winbond 83759A when operating in advanced mode.
* Multichip mode is not currently supported.
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index 4621807..ccee930 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -1329,6 +1329,11 @@ static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
}
}
+ /* Set max read request size to 4096. This slightly increases
+ * write throughput for pci-e variants.
+ */
+ pcie_set_readrq(pdev, 4096);
+
sil24_init_controller(host);
pci_set_master(pdev);
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2008-08-22 7:04 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2008-08-22 7:04 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Main items of note:
* Tejun's error handling (soft/hard reset) fixes
* Tejun's sata_mv fix
* Alan's dma_mode fixes
pata_via is a cleanup not a fix, but it is cleaning up some
vendor mistakes, with a net decrease in code size.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
Documentation/kernel-parameters.txt | 3 ++
drivers/ata/ahci.c | 8 +++--
drivers/ata/ata_piix.c | 8 +++++
drivers/ata/libata-core.c | 60 +++++++++++++++++++++-------------
drivers/ata/libata-eh.c | 30 +++++++----------
drivers/ata/pata_acpi.c | 2 +-
drivers/ata/pata_atiixp.c | 2 +-
drivers/ata/pata_cs5530.c | 6 ++--
drivers/ata/pata_it821x.c | 2 +-
drivers/ata/pata_oldpiix.c | 2 +-
drivers/ata/pata_sc1200.c | 6 ++--
drivers/ata/pata_via.c | 59 ++++++----------------------------
drivers/ata/sata_mv.c | 37 +++++++--------------
include/linux/libata.h | 24 ++++++++++++++
14 files changed, 123 insertions(+), 126 deletions(-)
Alan Cox (1):
libata: Fix a large collection of DMA mode mismatches
Jeff Garzik (1):
[libata] pata_it821x: fix warning
Saeed Bishara (1):
sata_mv: add the Gen IIE flag to the SoC devices.
Seth Heasley (2):
ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
Tejun Heo (8):
libata: implement no[hs]rst force params
sata_mv: don't issue two DMA commands concurrently
libata: fix EH action overwriting in ata_eh_reset()
libata: always do follow-up SRST if hardreset returned -EAGAIN
libata: use ata_link_printk() when printing SError
libata: restore SControl on detach
pata_via: clean up recent tf_load changes
ahci: sis controllers actually can do PMP
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index a897646..1150444 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -1074,6 +1074,9 @@ and is between 256 and 4096 characters. It is defined in the file
* [no]ncq: Turn on or off NCQ.
+ * nohrst, nosrst, norst: suppress hard, soft
+ and both resets.
+
If there are multiple matching configurations changing
the same attribute, the last one is used.
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index ef3e552..c729e69 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -486,6 +486,8 @@ static const struct pci_device_id ahci_pci_tbl[] = {
{ PCI_VDEVICE(INTEL, 0x502b), board_ahci }, /* Tolapai */
{ PCI_VDEVICE(INTEL, 0x3a05), board_ahci }, /* ICH10 */
{ PCI_VDEVICE(INTEL, 0x3a25), board_ahci }, /* ICH10 */
+ { PCI_VDEVICE(INTEL, 0x3b24), board_ahci }, /* PCH RAID */
+ { PCI_VDEVICE(INTEL, 0x3b2b), board_ahci }, /* PCH RAID */
/* JMicron 360/1/3/5/6, match class to avoid IDE function */
{ PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
@@ -575,9 +577,9 @@ static const struct pci_device_id ahci_pci_tbl[] = {
{ PCI_VDEVICE(NVIDIA, 0x0bc7), board_ahci }, /* MCP7B */
/* SiS */
- { PCI_VDEVICE(SI, 0x1184), board_ahci_nopmp }, /* SiS 966 */
- { PCI_VDEVICE(SI, 0x1185), board_ahci_nopmp }, /* SiS 968 */
- { PCI_VDEVICE(SI, 0x0186), board_ahci_nopmp }, /* SiS 968 */
+ { PCI_VDEVICE(SI, 0x1184), board_ahci }, /* SiS 966 */
+ { PCI_VDEVICE(SI, 0x1185), board_ahci }, /* SiS 968 */
+ { PCI_VDEVICE(SI, 0x0186), board_ahci }, /* SiS 968 */
/* Marvell */
{ PCI_VDEVICE(MARVELL, 0x6145), board_ahci_mv }, /* 6145 */
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index c294121..b1d08a8 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -275,6 +275,14 @@ static const struct pci_device_id piix_pci_tbl[] = {
{ 0x8086, 0x3a20, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
/* SATA Controller IDE (ICH10) */
{ 0x8086, 0x3a26, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
+ /* SATA Controller IDE (PCH) */
+ { 0x8086, 0x3b20, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
+ /* SATA Controller IDE (PCH) */
+ { 0x8086, 0x3b26, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
+ /* SATA Controller IDE (PCH) */
+ { 0x8086, 0x3b2d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
+ /* SATA Controller IDE (PCH) */
+ { 0x8086, 0x3b2e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
{ } /* terminate list */
};
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 5ba96c5..79e3a8e 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -104,6 +104,7 @@ struct ata_force_param {
unsigned long xfer_mask;
unsigned int horkage_on;
unsigned int horkage_off;
+ unsigned int lflags;
};
struct ata_force_ent {
@@ -196,22 +197,23 @@ void ata_force_cbl(struct ata_port *ap)
}
/**
- * ata_force_spd_limit - force SATA spd limit according to libata.force
+ * ata_force_link_limits - force link limits according to libata.force
* @link: ATA link of interest
*
- * Force SATA spd limit according to libata.force and whine about
- * it. When only the port part is specified (e.g. 1:), the limit
- * applies to all links connected to both the host link and all
- * fan-out ports connected via PMP. If the device part is
- * specified as 0 (e.g. 1.00:), it specifies the first fan-out
- * link not the host link. Device number 15 always points to the
- * host link whether PMP is attached or not.
+ * Force link flags and SATA spd limit according to libata.force
+ * and whine about it. When only the port part is specified
+ * (e.g. 1:), the limit applies to all links connected to both
+ * the host link and all fan-out ports connected via PMP. If the
+ * device part is specified as 0 (e.g. 1.00:), it specifies the
+ * first fan-out link not the host link. Device number 15 always
+ * points to the host link whether PMP is attached or not.
*
* LOCKING:
* EH context.
*/
-static void ata_force_spd_limit(struct ata_link *link)
+static void ata_force_link_limits(struct ata_link *link)
{
+ bool did_spd = false;
int linkno, i;
if (ata_is_host_link(link))
@@ -228,13 +230,22 @@ static void ata_force_spd_limit(struct ata_link *link)
if (fe->device != -1 && fe->device != linkno)
continue;
- if (!fe->param.spd_limit)
- continue;
+ /* only honor the first spd limit */
+ if (!did_spd && fe->param.spd_limit) {
+ link->hw_sata_spd_limit = (1 << fe->param.spd_limit) - 1;
+ ata_link_printk(link, KERN_NOTICE,
+ "FORCE: PHY spd limit set to %s\n",
+ fe->param.name);
+ did_spd = true;
+ }
- link->hw_sata_spd_limit = (1 << fe->param.spd_limit) - 1;
- ata_link_printk(link, KERN_NOTICE,
- "FORCE: PHY spd limit set to %s\n", fe->param.name);
- return;
+ /* let lflags stack */
+ if (fe->param.lflags) {
+ link->flags |= fe->param.lflags;
+ ata_link_printk(link, KERN_NOTICE,
+ "FORCE: link flag 0x%x forced -> 0x%x\n",
+ fe->param.lflags, link->flags);
+ }
}
}
@@ -3277,7 +3288,7 @@ int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev)
dev->dma_mode = ata_xfer_mask2mode(dma_mask);
found = 1;
- if (dev->dma_mode != 0xff)
+ if (ata_dma_enabled(dev))
used_dma = 1;
}
if (!found)
@@ -3302,7 +3313,7 @@ int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev)
/* step 3: set host DMA timings */
ata_link_for_each_dev(dev, link) {
- if (!ata_dev_enabled(dev) || dev->dma_mode == 0xff)
+ if (!ata_dev_enabled(dev) || !ata_dma_enabled(dev))
continue;
dev->xfer_mode = dev->dma_mode;
@@ -5188,19 +5199,18 @@ void ata_link_init(struct ata_port *ap, struct ata_link *link, int pmp)
*/
int sata_link_init_spd(struct ata_link *link)
{
- u32 scontrol;
u8 spd;
int rc;
- rc = sata_scr_read(link, SCR_CONTROL, &scontrol);
+ rc = sata_scr_read(link, SCR_CONTROL, &link->saved_scontrol);
if (rc)
return rc;
- spd = (scontrol >> 4) & 0xf;
+ spd = (link->saved_scontrol >> 4) & 0xf;
if (spd)
link->hw_sata_spd_limit &= (1 << spd) - 1;
- ata_force_spd_limit(link);
+ ata_force_link_limits(link);
link->sata_spd_limit = link->hw_sata_spd_limit;
@@ -5783,9 +5793,10 @@ static void ata_port_detach(struct ata_port *ap)
ata_port_wait_eh(ap);
/* EH is now guaranteed to see UNLOADING - EH context belongs
- * to us. Disable all existing devices.
+ * to us. Restore SControl and disable all existing devices.
*/
- ata_port_for_each_link(link, ap) {
+ __ata_port_for_each_link(link, ap) {
+ sata_scr_write(link, SCR_CONTROL, link->saved_scontrol);
ata_link_for_each_dev(dev, link)
ata_dev_disable(dev);
}
@@ -5991,6 +6002,9 @@ static int __init ata_parse_force_one(char **cur,
{ "udma133", .xfer_mask = 1 << (ATA_SHIFT_UDMA + 6) },
{ "udma/133", .xfer_mask = 1 << (ATA_SHIFT_UDMA + 6) },
{ "udma7", .xfer_mask = 1 << (ATA_SHIFT_UDMA + 7) },
+ { "nohrst", .lflags = ATA_LFLAG_NO_HRST },
+ { "nosrst", .lflags = ATA_LFLAG_NO_SRST },
+ { "norst", .lflags = ATA_LFLAG_NO_HRST | ATA_LFLAG_NO_SRST },
};
char *start = *cur, *p = *cur;
char *id, *val, *endp;
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 58bdc53..c1db2f2 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -2040,7 +2040,7 @@ static void ata_eh_link_report(struct ata_link *link)
}
if (ehc->i.serror)
- ata_port_printk(ap, KERN_ERR,
+ ata_link_printk(link, KERN_ERR,
"SError: { %s%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s}\n",
ehc->i.serror & SERR_DATA_RECOVERED ? "RecovData " : "",
ehc->i.serror & SERR_COMM_RECOVERED ? "RecovComm " : "",
@@ -2171,18 +2171,12 @@ static int ata_do_reset(struct ata_link *link, ata_reset_fn_t reset,
}
static int ata_eh_followup_srst_needed(struct ata_link *link,
- int rc, int classify,
- const unsigned int *classes)
+ int rc, const unsigned int *classes)
{
if ((link->flags & ATA_LFLAG_NO_SRST) || ata_link_offline(link))
return 0;
- if (rc == -EAGAIN) {
- if (classify)
- return 1;
- rc = 0;
- }
- if (rc != 0)
- return 0;
+ if (rc == -EAGAIN)
+ return 1;
if (sata_pmp_supported(link->ap) && ata_is_host_link(link))
return 1;
return 0;
@@ -2210,6 +2204,10 @@ int ata_eh_reset(struct ata_link *link, int classify,
*/
while (ata_eh_reset_timeouts[max_tries] != ULONG_MAX)
max_tries++;
+ if (link->flags & ATA_LFLAG_NO_HRST)
+ hardreset = NULL;
+ if (link->flags & ATA_LFLAG_NO_SRST)
+ softreset = NULL;
now = jiffies;
deadline = ata_deadline(ehc->last_reset, ATA_EH_RESET_COOL_DOWN);
@@ -2247,10 +2245,10 @@ int ata_eh_reset(struct ata_link *link, int classify,
ehc->i.action &= ~ATA_EH_RESET;
if (hardreset) {
reset = hardreset;
- ehc->i.action = ATA_EH_HARDRESET;
+ ehc->i.action |= ATA_EH_HARDRESET;
} else if (softreset) {
reset = softreset;
- ehc->i.action = ATA_EH_SOFTRESET;
+ ehc->i.action |= ATA_EH_SOFTRESET;
}
if (prereset) {
@@ -2305,9 +2303,11 @@ int ata_eh_reset(struct ata_link *link, int classify,
ehc->i.flags |= ATA_EHI_DID_SOFTRESET;
rc = ata_do_reset(link, reset, classes, deadline);
+ if (rc && rc != -EAGAIN)
+ goto fail;
if (reset == hardreset &&
- ata_eh_followup_srst_needed(link, rc, classify, classes)) {
+ ata_eh_followup_srst_needed(link, rc, classes)) {
/* okay, let's do follow-up softreset */
reset = softreset;
@@ -2322,10 +2322,6 @@ int ata_eh_reset(struct ata_link *link, int classify,
ata_eh_about_to_do(link, NULL, ATA_EH_RESET);
rc = ata_do_reset(link, reset, classes, deadline);
}
-
- /* -EAGAIN can happen if we skipped followup SRST */
- if (rc && rc != -EAGAIN)
- goto fail;
} else {
if (verbose)
ata_link_printk(link, KERN_INFO, "no reset method "
diff --git a/drivers/ata/pata_acpi.c b/drivers/ata/pata_acpi.c
index fbe6057..eb919c1 100644
--- a/drivers/ata/pata_acpi.c
+++ b/drivers/ata/pata_acpi.c
@@ -181,7 +181,7 @@ static unsigned int pacpi_qc_issue(struct ata_queued_cmd *qc)
if (adev != acpi->last) {
pacpi_set_piomode(ap, adev);
- if (adev->dma_mode)
+ if (ata_dma_enabled(adev))
pacpi_set_dmamode(ap, adev);
acpi->last = adev;
}
diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
index d7de7ba..e8a0d99 100644
--- a/drivers/ata/pata_atiixp.c
+++ b/drivers/ata/pata_atiixp.c
@@ -183,7 +183,7 @@ static void atiixp_bmdma_start(struct ata_queued_cmd *qc)
u16 tmp16;
pci_read_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, &tmp16);
- if (adev->dma_mode >= XFER_UDMA_0)
+ if (ata_using_udma(adev))
tmp16 |= (1 << dn);
else
tmp16 &= ~(1 << dn);
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
index 744beeb..0c4b271 100644
--- a/drivers/ata/pata_cs5530.c
+++ b/drivers/ata/pata_cs5530.c
@@ -149,10 +149,10 @@ static unsigned int cs5530_qc_issue(struct ata_queued_cmd *qc)
struct ata_device *prev = ap->private_data;
/* See if the DMA settings could be wrong */
- if (adev->dma_mode != 0 && adev != prev && prev != NULL) {
+ if (ata_dma_enabled(adev) && adev != prev && prev != NULL) {
/* Maybe, but do the channels match MWDMA/UDMA ? */
- if ((adev->dma_mode >= XFER_UDMA_0 && prev->dma_mode < XFER_UDMA_0) ||
- (adev->dma_mode < XFER_UDMA_0 && prev->dma_mode >= XFER_UDMA_0))
+ if ((ata_using_udma(adev) && !ata_using_udma(prev)) ||
+ (ata_using_udma(prev) && !ata_using_udma(adev)))
/* Switch the mode bits */
cs5530_set_dmamode(ap, adev);
}
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
index 27843c7..0221c9a 100644
--- a/drivers/ata/pata_it821x.c
+++ b/drivers/ata/pata_it821x.c
@@ -606,7 +606,7 @@ static void it821x_display_disk(int n, u8 *buf)
{
unsigned char id[41];
int mode = 0;
- char *mtype;
+ char *mtype = "";
char mbuf[8];
char *cbl = "(40 wire cable)";
diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c
index e678af3..df64f24 100644
--- a/drivers/ata/pata_oldpiix.c
+++ b/drivers/ata/pata_oldpiix.c
@@ -198,7 +198,7 @@ static unsigned int oldpiix_qc_issue(struct ata_queued_cmd *qc)
if (adev != ap->private_data) {
oldpiix_set_piomode(ap, adev);
- if (adev->dma_mode)
+ if (ata_dma_enabled(adev))
oldpiix_set_dmamode(ap, adev);
}
return ata_sff_qc_issue(qc);
diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c
index cbab397..0278fd2 100644
--- a/drivers/ata/pata_sc1200.c
+++ b/drivers/ata/pata_sc1200.c
@@ -167,10 +167,10 @@ static unsigned int sc1200_qc_issue(struct ata_queued_cmd *qc)
struct ata_device *prev = ap->private_data;
/* See if the DMA settings could be wrong */
- if (adev->dma_mode != 0 && adev != prev && prev != NULL) {
+ if (ata_dma_enabled(adev) && adev != prev && prev != NULL) {
/* Maybe, but do the channels match MWDMA/UDMA ? */
- if ((adev->dma_mode >= XFER_UDMA_0 && prev->dma_mode < XFER_UDMA_0) ||
- (adev->dma_mode < XFER_UDMA_0 && prev->dma_mode >= XFER_UDMA_0))
+ if ((ata_using_udma(adev) && !ata_using_udma(prev)) ||
+ (ata_using_udma(prev) && !ata_using_udma(adev)))
/* Switch the mode bits */
sc1200_set_dmamode(ap, adev);
}
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 57d951b..8fdb2ce 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -324,62 +324,26 @@ static void via_set_dmamode(struct ata_port *ap, struct ata_device *adev)
}
/**
- * via_ata_sff_tf_load - send taskfile registers to host controller
+ * via_tf_load - send taskfile registers to host controller
* @ap: Port to which output is sent
* @tf: ATA taskfile register set
*
* Outputs ATA taskfile to standard ATA host controller.
*
* Note: This is to fix the internal bug of via chipsets, which
- * will reset the device register after changing the IEN bit on
- * ctl register
+ * will reset the device register after changing the IEN bit on
+ * ctl register
*/
-static void via_ata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
+static void via_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
{
- struct ata_ioports *ioaddr = &ap->ioaddr;
- unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
-
- if (tf->ctl != ap->last_ctl) {
- iowrite8(tf->ctl, ioaddr->ctl_addr);
- iowrite8(tf->device, ioaddr->device_addr);
- ap->last_ctl = tf->ctl;
- ata_wait_idle(ap);
- }
-
- if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
- iowrite8(tf->hob_feature, ioaddr->feature_addr);
- iowrite8(tf->hob_nsect, ioaddr->nsect_addr);
- iowrite8(tf->hob_lbal, ioaddr->lbal_addr);
- iowrite8(tf->hob_lbam, ioaddr->lbam_addr);
- iowrite8(tf->hob_lbah, ioaddr->lbah_addr);
- VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
- tf->hob_feature,
- tf->hob_nsect,
- tf->hob_lbal,
- tf->hob_lbam,
- tf->hob_lbah);
- }
+ struct ata_taskfile tmp_tf;
- if (is_addr) {
- iowrite8(tf->feature, ioaddr->feature_addr);
- iowrite8(tf->nsect, ioaddr->nsect_addr);
- iowrite8(tf->lbal, ioaddr->lbal_addr);
- iowrite8(tf->lbam, ioaddr->lbam_addr);
- iowrite8(tf->lbah, ioaddr->lbah_addr);
- VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
- tf->feature,
- tf->nsect,
- tf->lbal,
- tf->lbam,
- tf->lbah);
+ if (ap->ctl != ap->last_ctl && !(tf->flags & ATA_TFLAG_DEVICE)) {
+ tmp_tf = *tf;
+ tmp_tf.flags |= ATA_TFLAG_DEVICE;
+ tf = &tmp_tf;
}
-
- if (tf->flags & ATA_TFLAG_DEVICE) {
- iowrite8(tf->device, ioaddr->device_addr);
- VPRINTK("device 0x%X\n", tf->device);
- }
-
- ata_wait_idle(ap);
+ ata_sff_tf_load(ap, tf);
}
static struct scsi_host_template via_sht = {
@@ -392,13 +356,12 @@ static struct ata_port_operations via_port_ops = {
.set_piomode = via_set_piomode,
.set_dmamode = via_set_dmamode,
.prereset = via_pre_reset,
- .sff_tf_load = via_ata_tf_load,
+ .sff_tf_load = via_tf_load,
};
static struct ata_port_operations via_port_ops_noirq = {
.inherits = &via_port_ops,
.sff_data_xfer = ata_sff_data_xfer_noirq,
- .sff_tf_load = via_ata_tf_load,
};
/**
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index ad169ff..13c1d2a 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -1134,30 +1134,16 @@ static int mv_qc_defer(struct ata_queued_cmd *qc)
if (ap->nr_active_links == 0)
return 0;
- if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) {
- /*
- * The port is operating in host queuing mode (EDMA).
- * It can accomodate a new qc if the qc protocol
- * is compatible with the current host queue mode.
- */
- if (pp->pp_flags & MV_PP_FLAG_NCQ_EN) {
- /*
- * The host queue (EDMA) is in NCQ mode.
- * If the new qc is also an NCQ command,
- * then allow the new qc.
- */
- if (qc->tf.protocol == ATA_PROT_NCQ)
- return 0;
- } else {
- /*
- * The host queue (EDMA) is in non-NCQ, DMA mode.
- * If the new qc is also a non-NCQ, DMA command,
- * then allow the new qc.
- */
- if (qc->tf.protocol == ATA_PROT_DMA)
- return 0;
- }
- }
+ /*
+ * The port is operating in host queuing mode (EDMA) with NCQ
+ * enabled, allow multiple NCQ commands. EDMA also allows
+ * queueing multiple DMA commands but libata core currently
+ * doesn't allow it.
+ */
+ if ((pp->pp_flags & MV_PP_FLAG_EDMA_EN) &&
+ (pp->pp_flags & MV_PP_FLAG_NCQ_EN) && ata_is_ncq(qc->tf.protocol))
+ return 0;
+
return ATA_DEFER_PORT;
}
@@ -3036,7 +3022,8 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
break;
case chip_soc:
hpriv->ops = &mv_soc_ops;
- hp_flags |= MV_HP_FLAG_SOC | MV_HP_ERRATA_60X1C0;
+ hp_flags |= MV_HP_FLAG_SOC | MV_HP_GEN_IIE |
+ MV_HP_ERRATA_60X1C0;
break;
default:
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 06b8033..225bfc5 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -163,6 +163,7 @@ enum {
ATA_DEV_NONE = 9, /* no device */
/* struct ata_link flags */
+ ATA_LFLAG_NO_HRST = (1 << 1), /* avoid hardreset */
ATA_LFLAG_NO_SRST = (1 << 2), /* avoid softreset */
ATA_LFLAG_ASSUME_ATA = (1 << 3), /* assume ATA class */
ATA_LFLAG_ASSUME_SEMB = (1 << 4), /* assume SEMB class */
@@ -646,6 +647,7 @@ struct ata_link {
unsigned int flags; /* ATA_LFLAG_xxx */
+ u32 saved_scontrol; /* SControl on probe */
unsigned int hw_sata_spd_limit;
unsigned int sata_spd_limit;
unsigned int sata_spd; /* current SATA PHY speed */
@@ -1427,6 +1429,28 @@ static inline unsigned long ata_deadline(unsigned long from_jiffies,
return from_jiffies + msecs_to_jiffies(timeout_msecs);
}
+/* Don't open code these in drivers as there are traps. Firstly the range may
+ change in future hardware and specs, secondly 0xFF means 'no DMA' but is
+ > UDMA_0. Dyma ddreigiau */
+
+static inline int ata_using_mwdma(struct ata_device *adev)
+{
+ if (adev->dma_mode >= XFER_MW_DMA_0 && adev->dma_mode <= XFER_MW_DMA_4)
+ return 1;
+ return 0;
+}
+
+static inline int ata_using_udma(struct ata_device *adev)
+{
+ if (adev->dma_mode >= XFER_UDMA_0 && adev->dma_mode <= XFER_UDMA_7)
+ return 1;
+ return 0;
+}
+
+static inline int ata_dma_enabled(struct ata_device *adev)
+{
+ return (adev->dma_mode == 0xFF ? 0 : 1);
+}
/**************************************************************************
* PMP - drivers/ata/libata-pmp.c
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2008-07-31 6:51 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2008-07-31 6:51 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/ata_piix.c | 1 +
drivers/ata/libata-core.c | 57 ++++++++--
drivers/ata/libata-scsi.c | 34 +------
drivers/ata/libata.h | 1 -
drivers/ata/pata_ali.c | 3 +-
drivers/ata/pata_it821x.c | 270 +++++++++++++++++++++++++++++++++++++++------
drivers/ata/pata_via.c | 64 +++++++++++-
include/linux/libata.h | 9 +-
8 files changed, 356 insertions(+), 83 deletions(-)
Alan Cox (1):
pata_it821x: Driver updates and reworking
Alexander Beregalov (1):
libata.h: replace __FUNCTION__ with __func__
Ben Dooks (1):
pata_ali: misplaced pci_dev_put()
Elias Oltmanns (1):
libata-core: make sure that ata_force_tbl is freed in case of an error
JosephChan@via.com.tw (1):
pata_via: add VX800 flag; add function for fixing h/w bugs
Tejun Heo (2):
libata: update atapi disable handling
ata_piix: subsys 106b:00a3 is apple ich8m too
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index a90ae03..c294121 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -250,6 +250,7 @@ static const struct pci_device_id piix_pci_tbl[] = {
/* Mobile SATA Controller IDE (ICH8M), Apple */
{ 0x8086, 0x2828, 0x106b, 0x00a0, 0, 0, ich8m_apple_sata },
{ 0x8086, 0x2828, 0x106b, 0x00a1, 0, 0, ich8m_apple_sata },
+ { 0x8086, 0x2828, 0x106b, 0x00a3, 0, 0, ich8m_apple_sata },
/* Mobile SATA Controller IDE (ICH8M) */
{ 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
/* SATA Controller IDE (ICH9) */
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 9bef1a8..5ba96c5 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -120,7 +120,7 @@ static char ata_force_param_buf[PAGE_SIZE] __initdata;
module_param_string(force, ata_force_param_buf, sizeof(ata_force_param_buf), 0);
MODULE_PARM_DESC(force, "Force ATA configurations including cable type, link speed and transfer mode (see Documentation/kernel-parameters.txt for details)");
-int atapi_enabled = 1;
+static int atapi_enabled = 1;
module_param(atapi_enabled, int, 0444);
MODULE_PARM_DESC(atapi_enabled, "Enable discovery of ATAPI devices (0=off, 1=on)");
@@ -1132,6 +1132,8 @@ void ata_id_string(const u16 *id, unsigned char *s,
{
unsigned int c;
+ BUG_ON(len & 1);
+
while (len > 0) {
c = id[ofs] >> 8;
*s = c;
@@ -1165,8 +1167,6 @@ void ata_id_c_string(const u16 *id, unsigned char *s,
{
unsigned char *p;
- WARN_ON(!(len & 1));
-
ata_id_string(id, s, ofs, len - 1);
p = s + strnlen(s, len - 1);
@@ -1886,6 +1886,23 @@ static u32 ata_pio_mask_no_iordy(const struct ata_device *adev)
}
/**
+ * ata_do_dev_read_id - default ID read method
+ * @dev: device
+ * @tf: proposed taskfile
+ * @id: data buffer
+ *
+ * Issue the identify taskfile and hand back the buffer containing
+ * identify data. For some RAID controllers and for pre ATA devices
+ * this function is wrapped or replaced by the driver
+ */
+unsigned int ata_do_dev_read_id(struct ata_device *dev,
+ struct ata_taskfile *tf, u16 *id)
+{
+ return ata_exec_internal(dev, tf, NULL, DMA_FROM_DEVICE,
+ id, sizeof(id[0]) * ATA_ID_WORDS, 0);
+}
+
+/**
* ata_dev_read_id - Read ID data from the specified device
* @dev: target device
* @p_class: pointer to class of the target device (may be changed)
@@ -1920,7 +1937,7 @@ int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class,
if (ata_msg_ctl(ap))
ata_dev_printk(dev, KERN_DEBUG, "%s: ENTER\n", __func__);
- retry:
+retry:
ata_tf_init(dev, &tf);
switch (class) {
@@ -1948,8 +1965,11 @@ int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class,
*/
tf.flags |= ATA_TFLAG_POLLING;
- err_mask = ata_exec_internal(dev, &tf, NULL, DMA_FROM_DEVICE,
- id, sizeof(id[0]) * ATA_ID_WORDS, 0);
+ if (ap->ops->read_id)
+ err_mask = ap->ops->read_id(dev, &tf, id);
+ else
+ err_mask = ata_do_dev_read_id(dev, &tf, id);
+
if (err_mask) {
if (err_mask & AC_ERR_NODEV_HINT) {
ata_dev_printk(dev, KERN_DEBUG,
@@ -2142,6 +2162,16 @@ int ata_dev_configure(struct ata_device *dev)
return 0;
}
+ if ((!atapi_enabled || (ap->flags & ATA_FLAG_NO_ATAPI)) &&
+ dev->class == ATA_DEV_ATAPI) {
+ ata_dev_printk(dev, KERN_WARNING,
+ "WARNING: ATAPI is %s, device ignored.\n",
+ atapi_enabled ? "not supported with this driver"
+ : "disabled");
+ ata_dev_disable(dev);
+ return 0;
+ }
+
/* let ACPI work its magic */
rc = ata_acpi_on_devcfg(dev);
if (rc)
@@ -6088,16 +6118,20 @@ static int __init ata_init(void)
ata_wq = create_workqueue("ata");
if (!ata_wq)
- return -ENOMEM;
+ goto free_force_tbl;
ata_aux_wq = create_singlethread_workqueue("ata_aux");
- if (!ata_aux_wq) {
- destroy_workqueue(ata_wq);
- return -ENOMEM;
- }
+ if (!ata_aux_wq)
+ goto free_wq;
printk(KERN_DEBUG "libata version " DRV_VERSION " loaded.\n");
return 0;
+
+free_wq:
+ destroy_workqueue(ata_wq);
+free_force_tbl:
+ kfree(ata_force_tbl);
+ return -ENOMEM;
}
static void __exit ata_exit(void)
@@ -6269,6 +6303,7 @@ EXPORT_SYMBOL_GPL(ata_host_resume);
#endif /* CONFIG_PM */
EXPORT_SYMBOL_GPL(ata_id_string);
EXPORT_SYMBOL_GPL(ata_id_c_string);
+EXPORT_SYMBOL_GPL(ata_do_dev_read_id);
EXPORT_SYMBOL_GPL(ata_scsi_simulate);
EXPORT_SYMBOL_GPL(ata_pio_need_iordy);
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index f3b4b15..b9d3ba4 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -2551,36 +2551,6 @@ static struct ata_device *__ata_scsi_find_dev(struct ata_port *ap,
}
/**
- * ata_scsi_dev_enabled - determine if device is enabled
- * @dev: ATA device
- *
- * Determine if commands should be sent to the specified device.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- *
- * RETURNS:
- * 0 if commands are not allowed / 1 if commands are allowed
- */
-
-static int ata_scsi_dev_enabled(struct ata_device *dev)
-{
- if (unlikely(!ata_dev_enabled(dev)))
- return 0;
-
- if (!atapi_enabled || (dev->link->ap->flags & ATA_FLAG_NO_ATAPI)) {
- if (unlikely(dev->class == ATA_DEV_ATAPI)) {
- ata_dev_printk(dev, KERN_WARNING,
- "WARNING: ATAPI is %s, device ignored.\n",
- atapi_enabled ? "not supported with this driver" : "disabled");
- return 0;
- }
- }
-
- return 1;
-}
-
-/**
* ata_scsi_find_dev - lookup ata_device from scsi_cmnd
* @ap: ATA port to which the device is attached
* @scsidev: SCSI device from which we derive the ATA device
@@ -2601,7 +2571,7 @@ ata_scsi_find_dev(struct ata_port *ap, const struct scsi_device *scsidev)
{
struct ata_device *dev = __ata_scsi_find_dev(ap, scsidev);
- if (unlikely(!dev || !ata_scsi_dev_enabled(dev)))
+ if (unlikely(!dev || !ata_dev_enabled(dev)))
return NULL;
return dev;
@@ -3622,7 +3592,7 @@ int ata_sas_queuecmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *),
ata_scsi_dump_cdb(ap, cmd);
- if (likely(ata_scsi_dev_enabled(ap->link.device)))
+ if (likely(ata_dev_enabled(ap->link.device)))
rc = __ata_scsi_queuecmd(cmd, done, ap->link.device);
else {
cmd->result = (DID_BAD_TARGET << 16);
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index f6f9c28..ade5c75 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -66,7 +66,6 @@ enum {
extern unsigned int ata_print_id;
extern struct workqueue_struct *ata_aux_wq;
-extern int atapi_enabled;
extern int atapi_passthru16;
extern int libata_fua;
extern int libata_noacpi;
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index 0f3e659..5ca70fa 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -550,8 +550,9 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
pci_read_config_byte(isa_bridge, 0x5E, &tmp);
if ((tmp & 0x1E) == 0x12)
ppi[0] = &info_20_udma;
- pci_dev_put(isa_bridge);
}
+ pci_dev_put(isa_bridge);
+
return ata_pci_sff_init_one(pdev, ppi, &ali_sht, NULL);
}
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
index e108169..27843c7 100644
--- a/drivers/ata/pata_it821x.c
+++ b/drivers/ata/pata_it821x.c
@@ -80,7 +80,7 @@
#define DRV_NAME "pata_it821x"
-#define DRV_VERSION "0.3.8"
+#define DRV_VERSION "0.4.0"
struct it821x_dev
{
@@ -425,6 +425,8 @@ static unsigned int it821x_smart_qc_issue(struct ata_queued_cmd *qc)
case ATA_CMD_WRITE_MULTI:
case ATA_CMD_WRITE_MULTI_EXT:
case ATA_CMD_ID_ATA:
+ case ATA_CMD_INIT_DEV_PARAMS:
+ case 0xFC: /* Internal 'report rebuild state' */
/* Arguably should just no-op this one */
case ATA_CMD_SET_FEATURES:
return ata_sff_qc_issue(qc);
@@ -509,7 +511,7 @@ static void it821x_dev_config(struct ata_device *adev)
if (strstr(model_num, "Integrated Technology Express")) {
/* RAID mode */
- printk(KERN_INFO "IT821x %sRAID%d volume",
+ ata_dev_printk(adev, KERN_INFO, "%sRAID%d volume",
adev->id[147]?"Bootable ":"",
adev->id[129]);
if (adev->id[129] != 1)
@@ -519,37 +521,51 @@ static void it821x_dev_config(struct ata_device *adev)
/* This is a controller firmware triggered funny, don't
report the drive faulty! */
adev->horkage &= ~ATA_HORKAGE_DIAGNOSTIC;
+ /* No HPA in 'smart' mode */
+ adev->horkage |= ATA_HORKAGE_BROKEN_HPA;
}
/**
- * it821x_ident_hack - Hack identify data up
- * @ap: Port
+ * it821x_read_id - Hack identify data up
+ * @adev: device to read
+ * @tf: proposed taskfile
+ * @id: buffer for returned ident data
*
- * Walk the devices on this firmware driven port and slightly
+ * Query the devices on this firmware driven port and slightly
* mash the identify data to stop us and common tools trying to
* use features not firmware supported. The firmware itself does
* some masking (eg SMART) but not enough.
- *
- * This is a bit of an abuse of the cable method, but it is the
- * only method called at the right time. We could modify the libata
- * core specifically for ident hacking but while we have one offender
- * it seems better to keep the fallout localised.
*/
-static int it821x_ident_hack(struct ata_port *ap)
+static unsigned int it821x_read_id(struct ata_device *adev,
+ struct ata_taskfile *tf, u16 *id)
{
- struct ata_device *adev;
- ata_link_for_each_dev(adev, &ap->link) {
- if (ata_dev_enabled(adev)) {
- adev->id[84] &= ~(1 << 6); /* No FUA */
- adev->id[85] &= ~(1 << 10); /* No HPA */
- adev->id[76] = 0; /* No NCQ/AN etc */
- }
+ unsigned int err_mask;
+ unsigned char model_num[ATA_ID_PROD_LEN + 1];
+
+ err_mask = ata_do_dev_read_id(adev, tf, id);
+ if (err_mask)
+ return err_mask;
+ ata_id_c_string(id, model_num, ATA_ID_PROD, sizeof(model_num));
+
+ id[83] &= ~(1 << 12); /* Cache flush is firmware handled */
+ id[83] &= ~(1 << 13); /* Ditto for LBA48 flushes */
+ id[84] &= ~(1 << 6); /* No FUA */
+ id[85] &= ~(1 << 10); /* No HPA */
+ id[76] = 0; /* No NCQ/AN etc */
+
+ if (strstr(model_num, "Integrated Technology Express")) {
+ /* Set feature bits the firmware neglects */
+ id[49] |= 0x0300; /* LBA, DMA */
+ id[82] |= 0x0400; /* LBA48 */
+ id[83] &= 0x7FFF;
+ id[83] |= 0x4000; /* Word 83 is valid */
+ id[86] |= 0x0400; /* LBA48 on */
+ id[ATA_ID_MAJOR_VER] |= 0x1F;
}
- return ata_cable_unknown(ap);
+ return err_mask;
}
-
/**
* it821x_check_atapi_dma - ATAPI DMA handler
* @qc: Command we are about to issue
@@ -577,6 +593,136 @@ static int it821x_check_atapi_dma(struct ata_queued_cmd *qc)
return 0;
}
+/**
+ * it821x_display_disk - display disk setup
+ * @n: Device number
+ * @buf: Buffer block from firmware
+ *
+ * Produce a nice informative display of the device setup as provided
+ * by the firmware.
+ */
+
+static void it821x_display_disk(int n, u8 *buf)
+{
+ unsigned char id[41];
+ int mode = 0;
+ char *mtype;
+ char mbuf[8];
+ char *cbl = "(40 wire cable)";
+
+ static const char *types[5] = {
+ "RAID0", "RAID1" "RAID 0+1", "JBOD", "DISK"
+ };
+
+ if (buf[52] > 4) /* No Disk */
+ return;
+
+ ata_id_c_string((u16 *)buf, id, 0, 41);
+
+ if (buf[51]) {
+ mode = ffs(buf[51]);
+ mtype = "UDMA";
+ } else if (buf[49]) {
+ mode = ffs(buf[49]);
+ mtype = "MWDMA";
+ }
+
+ if (buf[76])
+ cbl = "";
+
+ if (mode)
+ snprintf(mbuf, 8, "%5s%d", mtype, mode - 1);
+ else
+ strcpy(mbuf, "PIO");
+ if (buf[52] == 4)
+ printk(KERN_INFO "%d: %-6s %-8s %s %s\n",
+ n, mbuf, types[buf[52]], id, cbl);
+ else
+ printk(KERN_INFO "%d: %-6s %-8s Volume: %1d %s %s\n",
+ n, mbuf, types[buf[52]], buf[53], id, cbl);
+ if (buf[125] < 100)
+ printk(KERN_INFO "%d: Rebuilding: %d%%\n", n, buf[125]);
+}
+
+/**
+ * it821x_firmware_command - issue firmware command
+ * @ap: IT821x port to interrogate
+ * @cmd: command
+ * @len: length
+ *
+ * Issue firmware commands expecting data back from the controller. We
+ * use this to issue commands that do not go via the normal paths. Other
+ * commands such as 0xFC can be issued normally.
+ */
+
+static u8 *it821x_firmware_command(struct ata_port *ap, u8 cmd, int len)
+{
+ u8 status;
+ int n = 0;
+ u16 *buf = kmalloc(len, GFP_KERNEL);
+ if (buf == NULL) {
+ printk(KERN_ERR "it821x_firmware_command: Out of memory\n");
+ return NULL;
+ }
+ /* This isn't quite a normal ATA command as we are talking to the
+ firmware not the drives */
+ ap->ctl |= ATA_NIEN;
+ iowrite8(ap->ctl, ap->ioaddr.ctl_addr);
+ ata_wait_idle(ap);
+ iowrite8(ATA_DEVICE_OBS, ap->ioaddr.device_addr);
+ iowrite8(cmd, ap->ioaddr.command_addr);
+ udelay(1);
+ /* This should be almost immediate but a little paranoia goes a long
+ way. */
+ while(n++ < 10) {
+ status = ioread8(ap->ioaddr.status_addr);
+ if (status & ATA_ERR) {
+ kfree(buf);
+ printk(KERN_ERR "it821x_firmware_command: rejected\n");
+ return NULL;
+ }
+ if (status & ATA_DRQ) {
+ ioread16_rep(ap->ioaddr.data_addr, buf, len/2);
+ return (u8 *)buf;
+ }
+ mdelay(1);
+ }
+ kfree(buf);
+ printk(KERN_ERR "it821x_firmware_command: timeout\n");
+ return NULL;
+}
+
+/**
+ * it821x_probe_firmware - firmware reporting/setup
+ * @ap: IT821x port being probed
+ *
+ * Probe the firmware of the controller by issuing firmware command
+ * 0xFA and analysing the returned data.
+ */
+
+static void it821x_probe_firmware(struct ata_port *ap)
+{
+ u8 *buf;
+ int i;
+
+ /* This is a bit ugly as we can't just issue a task file to a device
+ as this is controller magic */
+
+ buf = it821x_firmware_command(ap, 0xFA, 512);
+
+ if (buf != NULL) {
+ printk(KERN_INFO "pata_it821x: Firmware %02X/%02X/%02X%02X\n",
+ buf[505],
+ buf[506],
+ buf[507],
+ buf[508]);
+ for (i = 0; i < 4; i++)
+ it821x_display_disk(i, buf + 128 * i);
+ kfree(buf);
+ }
+}
+
+
/**
* it821x_port_start - port setup
@@ -610,6 +756,8 @@ static int it821x_port_start(struct ata_port *ap)
/* Long I/O's although allowed in LBA48 space cause the
onboard firmware to enter the twighlight zone */
/* No ATAPI DMA in this mode either */
+ if (ap->port_no == 0)
+ it821x_probe_firmware(ap);
}
/* Pull the current clocks from 0x50 */
if (conf & (1 << (1 + ap->port_no)))
@@ -631,6 +779,25 @@ static int it821x_port_start(struct ata_port *ap)
return 0;
}
+/**
+ * it821x_rdc_cable - Cable detect for RDC1010
+ * @ap: port we are checking
+ *
+ * Return the RDC1010 cable type. Unlike the IT821x we know how to do
+ * this and can do host side cable detect
+ */
+
+static int it821x_rdc_cable(struct ata_port *ap)
+{
+ u16 r40;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+ pci_read_config_word(pdev, 0x40, &r40);
+ if (r40 & (1 << (2 + ap->port_no)))
+ return ATA_CBL_PATA40;
+ return ATA_CBL_PATA80;
+}
+
static struct scsi_host_template it821x_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
@@ -641,9 +808,10 @@ static struct ata_port_operations it821x_smart_port_ops = {
.check_atapi_dma= it821x_check_atapi_dma,
.qc_issue = it821x_smart_qc_issue,
- .cable_detect = it821x_ident_hack,
+ .cable_detect = ata_cable_80wire,
.set_mode = it821x_smart_set_mode,
.dev_config = it821x_dev_config,
+ .read_id = it821x_read_id,
.port_start = it821x_port_start,
};
@@ -664,8 +832,29 @@ static struct ata_port_operations it821x_passthru_port_ops = {
.port_start = it821x_port_start,
};
+static struct ata_port_operations it821x_rdc_port_ops = {
+ .inherits = &ata_bmdma_port_ops,
+
+ .check_atapi_dma= it821x_check_atapi_dma,
+ .sff_dev_select = it821x_passthru_dev_select,
+ .bmdma_start = it821x_passthru_bmdma_start,
+ .bmdma_stop = it821x_passthru_bmdma_stop,
+ .qc_issue = it821x_passthru_qc_issue,
+
+ .cable_detect = it821x_rdc_cable,
+ .set_piomode = it821x_passthru_set_piomode,
+ .set_dmamode = it821x_passthru_set_dmamode,
+
+ .port_start = it821x_port_start,
+};
+
static void it821x_disable_raid(struct pci_dev *pdev)
{
+ /* Neither the RDC nor the IT8211 */
+ if (pdev->vendor != PCI_VENDOR_ID_ITE ||
+ pdev->device != PCI_DEVICE_ID_ITE_8212)
+ return;
+
/* Reset local CPU, and set BIOS not ready */
pci_write_config_byte(pdev, 0x5E, 0x01);
@@ -690,6 +879,7 @@ static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
+ .udma_mask = ATA_UDMA6,
.port_ops = &it821x_smart_port_ops
};
static const struct ata_port_info info_passthru = {
@@ -699,6 +889,13 @@ static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.udma_mask = ATA_UDMA6,
.port_ops = &it821x_passthru_port_ops
};
+ static const struct ata_port_info info_rdc = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = 0x1f,
+ .mwdma_mask = 0x07,
+ /* No UDMA */
+ .port_ops = &it821x_rdc_port_ops
+ };
const struct ata_port_info *ppi[] = { NULL, NULL };
static char *mode[2] = { "pass through", "smart" };
@@ -707,21 +904,25 @@ static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
rc = pcim_enable_device(pdev);
if (rc)
return rc;
+
+ if (pdev->vendor == PCI_VENDOR_ID_RDC) {
+ ppi[0] = &info_rdc;
+ } else {
+ /* Force the card into bypass mode if so requested */
+ if (it8212_noraid) {
+ printk(KERN_INFO DRV_NAME ": forcing bypass mode.\n");
+ it821x_disable_raid(pdev);
+ }
+ pci_read_config_byte(pdev, 0x50, &conf);
+ conf &= 1;
- /* Force the card into bypass mode if so requested */
- if (it8212_noraid) {
- printk(KERN_INFO DRV_NAME ": forcing bypass mode.\n");
- it821x_disable_raid(pdev);
+ printk(KERN_INFO DRV_NAME": controller in %s mode.\n",
+ mode[conf]);
+ if (conf == 0)
+ ppi[0] = &info_passthru;
+ else
+ ppi[0] = &info_smart;
}
- pci_read_config_byte(pdev, 0x50, &conf);
- conf &= 1;
-
- printk(KERN_INFO DRV_NAME ": controller in %s mode.\n", mode[conf]);
- if (conf == 0)
- ppi[0] = &info_passthru;
- else
- ppi[0] = &info_smart;
-
return ata_pci_sff_init_one(pdev, ppi, &it821x_sht, NULL);
}
@@ -745,6 +946,7 @@ static int it821x_reinit_one(struct pci_dev *pdev)
static const struct pci_device_id it821x[] = {
{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), },
{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), },
+ { PCI_VDEVICE(RDC, 0x1010), },
{ },
};
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 708ed14..57d951b 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -98,7 +98,8 @@ static const struct via_isa_bridge {
u8 rev_max;
u16 flags;
} via_isa_bridges[] = {
- { "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
+ { "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, VIA_UDMA_133 |
+ VIA_BAD_AST | VIA_SATA_PATA },
{ "vt8237s", PCI_DEVICE_ID_VIA_8237S, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
{ "vt8251", PCI_DEVICE_ID_VIA_8251, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
{ "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST | VIA_SATA_PATA },
@@ -322,6 +323,65 @@ static void via_set_dmamode(struct ata_port *ap, struct ata_device *adev)
via_do_set_mode(ap, adev, adev->dma_mode, tclock[mode], set_ast, udma[mode]);
}
+/**
+ * via_ata_sff_tf_load - send taskfile registers to host controller
+ * @ap: Port to which output is sent
+ * @tf: ATA taskfile register set
+ *
+ * Outputs ATA taskfile to standard ATA host controller.
+ *
+ * Note: This is to fix the internal bug of via chipsets, which
+ * will reset the device register after changing the IEN bit on
+ * ctl register
+ */
+static void via_ata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
+
+ if (tf->ctl != ap->last_ctl) {
+ iowrite8(tf->ctl, ioaddr->ctl_addr);
+ iowrite8(tf->device, ioaddr->device_addr);
+ ap->last_ctl = tf->ctl;
+ ata_wait_idle(ap);
+ }
+
+ if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
+ iowrite8(tf->hob_feature, ioaddr->feature_addr);
+ iowrite8(tf->hob_nsect, ioaddr->nsect_addr);
+ iowrite8(tf->hob_lbal, ioaddr->lbal_addr);
+ iowrite8(tf->hob_lbam, ioaddr->lbam_addr);
+ iowrite8(tf->hob_lbah, ioaddr->lbah_addr);
+ VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
+ tf->hob_feature,
+ tf->hob_nsect,
+ tf->hob_lbal,
+ tf->hob_lbam,
+ tf->hob_lbah);
+ }
+
+ if (is_addr) {
+ iowrite8(tf->feature, ioaddr->feature_addr);
+ iowrite8(tf->nsect, ioaddr->nsect_addr);
+ iowrite8(tf->lbal, ioaddr->lbal_addr);
+ iowrite8(tf->lbam, ioaddr->lbam_addr);
+ iowrite8(tf->lbah, ioaddr->lbah_addr);
+ VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
+ tf->feature,
+ tf->nsect,
+ tf->lbal,
+ tf->lbam,
+ tf->lbah);
+ }
+
+ if (tf->flags & ATA_TFLAG_DEVICE) {
+ iowrite8(tf->device, ioaddr->device_addr);
+ VPRINTK("device 0x%X\n", tf->device);
+ }
+
+ ata_wait_idle(ap);
+}
+
static struct scsi_host_template via_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
@@ -332,11 +392,13 @@ static struct ata_port_operations via_port_ops = {
.set_piomode = via_set_piomode,
.set_dmamode = via_set_dmamode,
.prereset = via_pre_reset,
+ .sff_tf_load = via_ata_tf_load,
};
static struct ata_port_operations via_port_ops_noirq = {
.inherits = &via_port_ops,
.sff_data_xfer = ata_sff_data_xfer_noirq,
+ .sff_tf_load = via_ata_tf_load,
};
/**
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 5b247b8..06b8033 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -60,9 +60,9 @@
/* note: prints function name for you */
#ifdef ATA_DEBUG
-#define DPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __FUNCTION__, ## args)
+#define DPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __func__, ## args)
#ifdef ATA_VERBOSE_DEBUG
-#define VPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __FUNCTION__, ## args)
+#define VPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __func__, ## args)
#else
#define VPRINTK(fmt, args...)
#endif /* ATA_VERBOSE_DEBUG */
@@ -71,7 +71,7 @@
#define VPRINTK(fmt, args...)
#endif /* ATA_DEBUG */
-#define BPRINTK(fmt, args...) if (ap->flags & ATA_FLAG_DEBUGMSG) printk(KERN_ERR "%s: " fmt, __FUNCTION__, ## args)
+#define BPRINTK(fmt, args...) if (ap->flags & ATA_FLAG_DEBUGMSG) printk(KERN_ERR "%s: " fmt, __func__, ## args)
/* NEW: debug levels */
#define HAVE_LIBATA_MSG 1
@@ -750,6 +750,7 @@ struct ata_port_operations {
void (*set_piomode)(struct ata_port *ap, struct ata_device *dev);
void (*set_dmamode)(struct ata_port *ap, struct ata_device *dev);
int (*set_mode)(struct ata_link *link, struct ata_device **r_failed_dev);
+ unsigned int (*read_id)(struct ata_device *dev, struct ata_taskfile *tf, u16 *id);
void (*dev_config)(struct ata_device *dev);
@@ -951,6 +952,8 @@ extern void ata_id_string(const u16 *id, unsigned char *s,
unsigned int ofs, unsigned int len);
extern void ata_id_c_string(const u16 *id, unsigned char *s,
unsigned int ofs, unsigned int len);
+extern unsigned int ata_do_dev_read_id(struct ata_device *dev,
+ struct ata_taskfile *tf, u16 *id);
extern void ata_qc_complete(struct ata_queued_cmd *qc);
extern int ata_qc_complete_multiple(struct ata_port *ap, u32 qc_active);
extern void ata_scsi_simulate(struct ata_device *dev, struct scsi_cmnd *cmd,
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2008-05-19 22:57 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2008-05-19 22:57 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
sata_mv, sata_promise and PMP fixes
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/libata-acpi.c | 75 ++++++++++------
drivers/ata/libata-core.c | 40 +++++----
drivers/ata/libata-eh.c | 207 +++++++++++++++++++++++-------------------
drivers/ata/libata-pmp.c | 44 +++++-----
drivers/ata/libata-scsi.c | 6 --
drivers/ata/pata_ali.c | 10 +-
drivers/ata/pata_amd.c | 14 ++--
drivers/ata/pata_at32.c | 2 -
drivers/ata/pata_bf54x.c | 5 +-
drivers/ata/pata_cypress.c | 8 +-
drivers/ata/pata_legacy.c | 50 +++++-----
drivers/ata/pata_ns87410.c | 6 +-
drivers/ata/pata_ns87415.c | 4 +-
drivers/ata/pata_qdi.c | 16 ++--
drivers/ata/pata_sl82c105.c | 2 +-
drivers/ata/pata_via.c | 14 ++--
drivers/ata/pata_winbond.c | 6 +-
drivers/ata/sata_mv.c | 163 +++++++++++++++++++---------------
drivers/ata/sata_promise.c | 148 +++++++++++++++----------------
drivers/ata/sata_sil24.c | 11 +++
include/linux/libata.h | 6 +-
21 files changed, 453 insertions(+), 384 deletions(-)
Christophe Jaillet (1):
avr32/pata: avoid unnecessary memset (updated after comments)
Harvey Harrison (1):
ata: remove FIT() macro
Jeff Garzik (1):
drivers/ata: trim trailing whitespace
Mark Lord (10):
sata_mv: always do softreset
sata_mv: fis irq register fixes
sata_mv: group genIIe flags
sata_mv: async notify for genIIe only
sata_mv: don't blindly enable IRQs
sata_mv: consolidate main_irq_mask updates
sata_mv: fix pmp drives not found
sata_mv: disregard masked irqs
sata_mv: cache main_irq_mask register in hpriv
sata_mv: ensure empty request queue for FBS-NCQ EH
Matthew Garrett (1):
Fixups to ATA ACPI hotplug
Mikael Pettersson (3):
sata_promise: fix irq clearing buglets
sata_promise: mmio access cleanups
sata_promise: other cleanups
Sonic Zhang (1):
pata-bf54x: Set ATAPI HSM to control IDE device terminate sequence.
Tejun Heo (10):
libata: fix sata_link_hardreset() @online out parameter handling
libata: reorganize ata_eh_reset() no reset method path
libata: move reset freeze/thaw handling into ata_eh_reset()
libata: kill hotplug related race condition
libata: ignore recovered PHY errors
libata: increase PMP register access timeout to 3s
libata: make sure PMP notification is turned off during recovery
libata: don't schedule LPM action seperately during probing
sata_sil24: don't use NCQ if marvell 4140 PMP is attached
libata: ignore SIMG4726 config pseudo device
diff --git a/drivers/ata/libata-acpi.c b/drivers/ata/libata-acpi.c
index 70b77e0..dbf6ca7 100644
--- a/drivers/ata/libata-acpi.c
+++ b/drivers/ata/libata-acpi.c
@@ -118,8 +118,8 @@ static void ata_acpi_associate_ide_port(struct ata_port *ap)
ap->pflags |= ATA_PFLAG_INIT_GTM_VALID;
}
-static void ata_acpi_handle_hotplug(struct ata_port *ap, struct ata_device *dev,
- u32 event)
+static void ata_acpi_handle_hotplug(struct ata_port *ap, struct ata_device
+ *dev, u32 event)
{
char event_string[12];
char *envp[] = { event_string, NULL };
@@ -127,6 +127,9 @@ static void ata_acpi_handle_hotplug(struct ata_port *ap, struct ata_device *dev,
struct kobject *kobj = NULL;
int wait = 0;
unsigned long flags;
+ acpi_handle handle, tmphandle;
+ unsigned long sta;
+ acpi_status status;
if (!ap)
ap = dev->link->ap;
@@ -134,32 +137,57 @@ static void ata_acpi_handle_hotplug(struct ata_port *ap, struct ata_device *dev,
spin_lock_irqsave(ap->lock, flags);
+ if (dev)
+ handle = dev->acpi_handle;
+ else
+ handle = ap->acpi_handle;
+
+ status = acpi_get_handle(handle, "_EJ0", &tmphandle);
+ if (ACPI_FAILURE(status)) {
+ /* This device is not ejectable */
+ spin_unlock_irqrestore(ap->lock, flags);
+ return;
+ }
+
+ status = acpi_evaluate_integer(handle, "_STA", NULL, &sta);
+ if (ACPI_FAILURE(status)) {
+ printk ("Unable to determine bay status\n");
+ spin_unlock_irqrestore(ap->lock, flags);
+ return;
+ }
+
switch (event) {
case ACPI_NOTIFY_BUS_CHECK:
case ACPI_NOTIFY_DEVICE_CHECK:
ata_ehi_push_desc(ehi, "ACPI event");
- ata_ehi_hotplugged(ehi);
- ata_port_freeze(ap);
- break;
-
- case ACPI_NOTIFY_EJECT_REQUEST:
- ata_ehi_push_desc(ehi, "ACPI event");
- if (dev)
- dev->flags |= ATA_DFLAG_DETACH;
- else {
- struct ata_link *tlink;
- struct ata_device *tdev;
-
- ata_port_for_each_link(tlink, ap)
- ata_link_for_each_dev(tdev, tlink)
- tdev->flags |= ATA_DFLAG_DETACH;
+ if (!sta) {
+ /* Device has been unplugged */
+ if (dev)
+ dev->flags |= ATA_DFLAG_DETACH;
+ else {
+ struct ata_link *tlink;
+ struct ata_device *tdev;
+
+ ata_port_for_each_link(tlink, ap) {
+ ata_link_for_each_dev(tdev, tlink) {
+ tdev->flags |=
+ ATA_DFLAG_DETACH;
+ }
+ }
+ }
+ ata_port_schedule_eh(ap);
+ wait = 1;
+ } else {
+ ata_ehi_hotplugged(ehi);
+ ata_port_freeze(ap);
}
-
- ata_port_schedule_eh(ap);
- wait = 1;
- break;
}
+ spin_unlock_irqrestore(ap->lock, flags);
+
+ if (wait)
+ ata_port_wait_eh(ap);
+
if (dev) {
if (dev->sdev)
kobj = &dev->sdev->sdev_gendev.kobj;
@@ -170,11 +198,6 @@ static void ata_acpi_handle_hotplug(struct ata_port *ap, struct ata_device *dev,
sprintf(event_string, "BAY_EVENT=%d", event);
kobject_uevent_env(kobj, KOBJ_CHANGE, envp);
}
-
- spin_unlock_irqrestore(ap->lock, flags);
-
- if (wait)
- ata_port_wait_eh(ap);
}
static void ata_acpi_dev_notify(acpi_handle handle, u32 event, void *data)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 927b692..3c89f20 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -2126,6 +2126,13 @@ int ata_dev_configure(struct ata_device *dev)
dev->horkage |= ata_dev_blacklisted(dev);
ata_force_horkage(dev);
+ if (dev->horkage & ATA_HORKAGE_DISABLE) {
+ ata_dev_printk(dev, KERN_INFO,
+ "unsupported device, disabling\n");
+ ata_dev_disable(dev);
+ return 0;
+ }
+
/* let ACPI work its magic */
rc = ata_acpi_on_devcfg(dev);
if (rc)
@@ -3490,22 +3497,11 @@ int sata_link_resume(struct ata_link *link, const unsigned long *params,
if ((rc = sata_link_debounce(link, params, deadline)))
return rc;
- /* Clear SError. PMP and some host PHYs require this to
- * operate and clearing should be done before checking PHY
- * online status to avoid race condition (hotplugging between
- * link resume and status check).
- */
+ /* clear SError, some PHYs require this even for SRST to work */
if (!(rc = sata_scr_read(link, SCR_ERROR, &serror)))
rc = sata_scr_write(link, SCR_ERROR, serror);
- if (rc == 0 || rc == -EINVAL) {
- unsigned long flags;
- spin_lock_irqsave(link->ap->lock, flags);
- link->eh_info.serror = 0;
- spin_unlock_irqrestore(link->ap->lock, flags);
- rc = 0;
- }
- return rc;
+ return rc != -EINVAL ? rc : 0;
}
/**
@@ -3653,9 +3649,13 @@ int sata_link_hardreset(struct ata_link *link, const unsigned long *timing,
if (check_ready)
rc = ata_wait_ready(link, deadline, check_ready);
out:
- if (rc && rc != -EAGAIN)
+ if (rc && rc != -EAGAIN) {
+ /* online is set iff link is online && reset succeeded */
+ if (online)
+ *online = false;
ata_link_printk(link, KERN_ERR,
"COMRESET failed (errno=%d)\n", rc);
+ }
DPRINTK("EXIT, rc=%d\n", rc);
return rc;
}
@@ -3700,8 +3700,14 @@ int sata_std_hardreset(struct ata_link *link, unsigned int *class,
*/
void ata_std_postreset(struct ata_link *link, unsigned int *classes)
{
+ u32 serror;
+
DPRINTK("ENTER\n");
+ /* reset complete, clear SError */
+ if (!sata_scr_read(link, SCR_ERROR, &serror))
+ sata_scr_write(link, SCR_ERROR, serror);
+
/* print link status */
sata_print_link_status(link);
@@ -3894,8 +3900,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
{ "SAMSUNG CD-ROM SN-124", "N001", ATA_HORKAGE_NODMA },
{ "Seagate STT20000A", NULL, ATA_HORKAGE_NODMA },
/* Odd clown on sil3726/4726 PMPs */
- { "Config Disk", NULL, ATA_HORKAGE_NODMA |
- ATA_HORKAGE_SKIP_PM },
+ { "Config Disk", NULL, ATA_HORKAGE_DISABLE },
/* Weird ATAPI devices */
{ "TORiSAN DVD-ROM DRD-N216", NULL, ATA_HORKAGE_MAX_SEC_128 },
@@ -5616,7 +5621,7 @@ int ata_host_register(struct ata_host *host, struct scsi_host_template *sht)
spin_lock_irqsave(ap->lock, flags);
ehi->probe_mask |= ATA_ALL_DEVICES;
- ehi->action |= ATA_EH_RESET;
+ ehi->action |= ATA_EH_RESET | ATA_EH_LPM;
ehi->flags |= ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET;
ap->pflags &= ~ATA_PFLAG_INITIALIZING;
@@ -5649,7 +5654,6 @@ int ata_host_register(struct ata_host *host, struct scsi_host_template *sht)
struct ata_port *ap = host->ports[i];
ata_scsi_scan_host(ap, 1);
- ata_lpm_schedule(ap, ap->pm_policy);
}
return 0;
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 62e0331..7894d83 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -1308,12 +1308,7 @@ static void ata_eh_analyze_serror(struct ata_link *link)
unsigned int err_mask = 0, action = 0;
u32 hotplug_mask;
- if (serror & SERR_PERSISTENT) {
- err_mask |= AC_ERR_ATA_BUS;
- action |= ATA_EH_RESET;
- }
- if (serror &
- (SERR_DATA_RECOVERED | SERR_COMM_RECOVERED | SERR_DATA)) {
+ if (serror & (SERR_PERSISTENT | SERR_DATA)) {
err_mask |= AC_ERR_ATA_BUS;
action |= ATA_EH_RESET;
}
@@ -2047,19 +2042,11 @@ static int ata_do_reset(struct ata_link *link, ata_reset_fn_t reset,
unsigned int *classes, unsigned long deadline)
{
struct ata_device *dev;
- int rc;
ata_link_for_each_dev(dev, link)
classes[dev->devno] = ATA_DEV_UNKNOWN;
- rc = reset(link, classes, deadline);
-
- /* convert all ATA_DEV_UNKNOWN to ATA_DEV_NONE */
- ata_link_for_each_dev(dev, link)
- if (classes[dev->devno] == ATA_DEV_UNKNOWN)
- classes[dev->devno] = ATA_DEV_NONE;
-
- return rc;
+ return reset(link, classes, deadline);
}
static int ata_eh_followup_srst_needed(struct ata_link *link,
@@ -2096,9 +2083,11 @@ int ata_eh_reset(struct ata_link *link, int classify,
ata_reset_fn_t reset;
unsigned long flags;
u32 sstatus;
- int rc;
+ int nr_known, rc;
- /* about to reset */
+ /*
+ * Prepare to reset
+ */
spin_lock_irqsave(ap->lock, flags);
ap->pflags |= ATA_PFLAG_RESETTING;
spin_unlock_irqrestore(ap->lock, flags);
@@ -2124,16 +2113,8 @@ int ata_eh_reset(struct ata_link *link, int classify,
ap->ops->set_piomode(ap, dev);
}
- if (!softreset && !hardreset) {
- if (verbose)
- ata_link_printk(link, KERN_INFO, "no reset method "
- "available, skipping reset\n");
- if (!(lflags & ATA_LFLAG_ASSUME_CLASS))
- lflags |= ATA_LFLAG_ASSUME_ATA;
- goto done;
- }
-
/* prefer hardreset */
+ reset = NULL;
ehc->i.action &= ~ATA_EH_RESET;
if (hardreset) {
reset = hardreset;
@@ -2141,11 +2122,6 @@ int ata_eh_reset(struct ata_link *link, int classify,
} else if (softreset) {
reset = softreset;
ehc->i.action = ATA_EH_SOFTRESET;
- } else {
- ata_link_printk(link, KERN_ERR, "BUG: no reset method, "
- "please report to linux-ide@vger.kernel.org\n");
- dump_stack();
- return -EINVAL;
}
if (prereset) {
@@ -2165,55 +2141,71 @@ int ata_eh_reset(struct ata_link *link, int classify,
"prereset failed (errno=%d)\n", rc);
goto out;
}
- }
- /* prereset() might have cleared ATA_EH_RESET */
- if (!(ehc->i.action & ATA_EH_RESET)) {
- /* prereset told us not to reset, bang classes and return */
- ata_link_for_each_dev(dev, link)
- classes[dev->devno] = ATA_DEV_NONE;
- rc = 0;
- goto out;
+ /* prereset() might have cleared ATA_EH_RESET. If so,
+ * bang classes and return.
+ */
+ if (reset && !(ehc->i.action & ATA_EH_RESET)) {
+ ata_link_for_each_dev(dev, link)
+ classes[dev->devno] = ATA_DEV_NONE;
+ rc = 0;
+ goto out;
+ }
}
retry:
+ /*
+ * Perform reset
+ */
+ if (ata_is_host_link(link))
+ ata_eh_freeze_port(ap);
+
deadline = jiffies + ata_eh_reset_timeouts[try++];
- /* shut up during boot probing */
- if (verbose)
- ata_link_printk(link, KERN_INFO, "%s resetting link\n",
- reset == softreset ? "soft" : "hard");
+ if (reset) {
+ if (verbose)
+ ata_link_printk(link, KERN_INFO, "%s resetting link\n",
+ reset == softreset ? "soft" : "hard");
- /* mark that this EH session started with reset */
- if (reset == hardreset)
- ehc->i.flags |= ATA_EHI_DID_HARDRESET;
- else
- ehc->i.flags |= ATA_EHI_DID_SOFTRESET;
+ /* mark that this EH session started with reset */
+ if (reset == hardreset)
+ ehc->i.flags |= ATA_EHI_DID_HARDRESET;
+ else
+ ehc->i.flags |= ATA_EHI_DID_SOFTRESET;
- rc = ata_do_reset(link, reset, classes, deadline);
+ rc = ata_do_reset(link, reset, classes, deadline);
- if (reset == hardreset &&
- ata_eh_followup_srst_needed(link, rc, classify, classes)) {
- /* okay, let's do follow-up softreset */
- reset = softreset;
+ if (reset == hardreset &&
+ ata_eh_followup_srst_needed(link, rc, classify, classes)) {
+ /* okay, let's do follow-up softreset */
+ reset = softreset;
- if (!reset) {
- ata_link_printk(link, KERN_ERR,
- "follow-up softreset required "
- "but no softreset avaliable\n");
- rc = -EINVAL;
- goto fail;
+ if (!reset) {
+ ata_link_printk(link, KERN_ERR,
+ "follow-up softreset required "
+ "but no softreset avaliable\n");
+ rc = -EINVAL;
+ goto fail;
+ }
+
+ ata_eh_about_to_do(link, NULL, ATA_EH_RESET);
+ rc = ata_do_reset(link, reset, classes, deadline);
}
- ata_eh_about_to_do(link, NULL, ATA_EH_RESET);
- rc = ata_do_reset(link, reset, classes, deadline);
+ /* -EAGAIN can happen if we skipped followup SRST */
+ if (rc && rc != -EAGAIN)
+ goto fail;
+ } else {
+ if (verbose)
+ ata_link_printk(link, KERN_INFO, "no reset method "
+ "available, skipping reset\n");
+ if (!(lflags & ATA_LFLAG_ASSUME_CLASS))
+ lflags |= ATA_LFLAG_ASSUME_ATA;
}
- /* -EAGAIN can happen if we skipped followup SRST */
- if (rc && rc != -EAGAIN)
- goto fail;
-
- done:
+ /*
+ * Post-reset processing
+ */
ata_link_for_each_dev(dev, link) {
/* After the reset, the device state is PIO 0 and the
* controller state is undefined. Reset also wakes up
@@ -2236,9 +2228,53 @@ int ata_eh_reset(struct ata_link *link, int classify,
if (sata_scr_read(link, SCR_STATUS, &sstatus) == 0)
link->sata_spd = (sstatus >> 4) & 0xf;
+ /* thaw the port */
+ if (ata_is_host_link(link))
+ ata_eh_thaw_port(ap);
+
+ /* postreset() should clear hardware SError. Although SError
+ * is cleared during link resume, clearing SError here is
+ * necessary as some PHYs raise hotplug events after SRST.
+ * This introduces race condition where hotplug occurs between
+ * reset and here. This race is mediated by cross checking
+ * link onlineness and classification result later.
+ */
if (postreset)
postreset(link, classes);
+ /* clear cached SError */
+ spin_lock_irqsave(link->ap->lock, flags);
+ link->eh_info.serror = 0;
+ spin_unlock_irqrestore(link->ap->lock, flags);
+
+ /* Make sure onlineness and classification result correspond.
+ * Hotplug could have happened during reset and some
+ * controllers fail to wait while a drive is spinning up after
+ * being hotplugged causing misdetection. By cross checking
+ * link onlineness and classification result, those conditions
+ * can be reliably detected and retried.
+ */
+ nr_known = 0;
+ ata_link_for_each_dev(dev, link) {
+ /* convert all ATA_DEV_UNKNOWN to ATA_DEV_NONE */
+ if (classes[dev->devno] == ATA_DEV_UNKNOWN)
+ classes[dev->devno] = ATA_DEV_NONE;
+ else
+ nr_known++;
+ }
+
+ if (classify && !nr_known && ata_link_online(link)) {
+ if (try < max_tries) {
+ ata_link_printk(link, KERN_WARNING, "link online but "
+ "device misclassified, retrying\n");
+ rc = -EAGAIN;
+ goto fail;
+ }
+ ata_link_printk(link, KERN_WARNING,
+ "link online but device misclassified, "
+ "device detection might fail\n");
+ }
+
/* reset successful, schedule revalidation */
ata_eh_done(link, NULL, ATA_EH_RESET);
ehc->i.action |= ATA_EH_REVALIDATE;
@@ -2587,7 +2623,7 @@ int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
struct ata_link *link;
struct ata_device *dev;
int nr_failed_devs, nr_disabled_devs;
- int reset, rc;
+ int rc;
unsigned long flags;
DPRINTK("ENTER\n");
@@ -2630,7 +2666,6 @@ int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
rc = 0;
nr_failed_devs = 0;
nr_disabled_devs = 0;
- reset = 0;
/* if UNLOADING, finish immediately */
if (ap->pflags & ATA_PFLAG_UNLOADING)
@@ -2644,40 +2679,24 @@ int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
if (ata_eh_skip_recovery(link))
ehc->i.action = 0;
- /* do we need to reset? */
- if (ehc->i.action & ATA_EH_RESET)
- reset = 1;
-
ata_link_for_each_dev(dev, link)
ehc->classes[dev->devno] = ATA_DEV_UNKNOWN;
}
/* reset */
- if (reset) {
- /* if PMP is attached, this function only deals with
- * downstream links, port should stay thawed.
- */
- if (!sata_pmp_attached(ap))
- ata_eh_freeze_port(ap);
-
- ata_port_for_each_link(link, ap) {
- struct ata_eh_context *ehc = &link->eh_context;
+ ata_port_for_each_link(link, ap) {
+ struct ata_eh_context *ehc = &link->eh_context;
- if (!(ehc->i.action & ATA_EH_RESET))
- continue;
+ if (!(ehc->i.action & ATA_EH_RESET))
+ continue;
- rc = ata_eh_reset(link, ata_link_nr_vacant(link),
- prereset, softreset, hardreset,
- postreset);
- if (rc) {
- ata_link_printk(link, KERN_ERR,
- "reset failed, giving up\n");
- goto out;
- }
+ rc = ata_eh_reset(link, ata_link_nr_vacant(link),
+ prereset, softreset, hardreset, postreset);
+ if (rc) {
+ ata_link_printk(link, KERN_ERR,
+ "reset failed, giving up\n");
+ goto out;
}
-
- if (!sata_pmp_attached(ap))
- ata_eh_thaw_port(ap);
}
/* the rest */
diff --git a/drivers/ata/libata-pmp.c b/drivers/ata/libata-pmp.c
index ff1822a..0f9386d 100644
--- a/drivers/ata/libata-pmp.c
+++ b/drivers/ata/libata-pmp.c
@@ -48,7 +48,7 @@ static unsigned int sata_pmp_read(struct ata_link *link, int reg, u32 *r_val)
tf.device = link->pmp;
err_mask = ata_exec_internal(pmp_dev, &tf, NULL, DMA_NONE, NULL, 0,
- SATA_PMP_SCR_TIMEOUT);
+ SATA_PMP_RW_TIMEOUT);
if (err_mask)
return err_mask;
@@ -88,7 +88,7 @@ static unsigned int sata_pmp_write(struct ata_link *link, int reg, u32 val)
tf.lbah = (val >> 24) & 0xff;
return ata_exec_internal(pmp_dev, &tf, NULL, DMA_NONE, NULL, 0,
- SATA_PMP_SCR_TIMEOUT);
+ SATA_PMP_RW_TIMEOUT);
}
/**
@@ -257,19 +257,6 @@ static int sata_pmp_configure(struct ata_device *dev, int print_info)
goto fail;
}
- /* turn off notification till fan-out ports are reset and configured */
- if (gscr[SATA_PMP_GSCR_FEAT_EN] & SATA_PMP_FEAT_NOTIFY) {
- gscr[SATA_PMP_GSCR_FEAT_EN] &= ~SATA_PMP_FEAT_NOTIFY;
-
- err_mask = sata_pmp_write(dev->link, SATA_PMP_GSCR_FEAT_EN,
- gscr[SATA_PMP_GSCR_FEAT_EN]);
- if (err_mask) {
- rc = -EIO;
- reason = "failed to write GSCR_FEAT_EN";
- goto fail;
- }
- }
-
if (print_info) {
ata_dev_printk(dev, KERN_INFO, "Port Multiplier %s, "
"0x%04x:0x%04x r%d, %d ports, feat 0x%x/0x%x\n",
@@ -700,8 +687,6 @@ static int sata_pmp_eh_recover_pmp(struct ata_port *ap,
if (ehc->i.action & ATA_EH_RESET) {
struct ata_link *tlink;
- ata_eh_freeze_port(ap);
-
/* reset */
rc = ata_eh_reset(link, 0, prereset, softreset, hardreset,
postreset);
@@ -711,8 +696,6 @@ static int sata_pmp_eh_recover_pmp(struct ata_port *ap,
goto fail;
}
- ata_eh_thaw_port(ap);
-
/* PMP is reset, SErrors cannot be trusted, scan all */
ata_port_for_each_link(tlink, ap) {
struct ata_eh_context *ehc = &tlink->eh_context;
@@ -864,6 +847,7 @@ static int sata_pmp_eh_recover(struct ata_port *ap)
struct ata_link *pmp_link = &ap->link;
struct ata_device *pmp_dev = pmp_link->device;
struct ata_eh_context *pmp_ehc = &pmp_link->eh_context;
+ u32 *gscr = pmp_dev->gscr;
struct ata_link *link;
struct ata_device *dev;
unsigned int err_mask;
@@ -901,6 +885,22 @@ static int sata_pmp_eh_recover(struct ata_port *ap)
if (rc)
goto pmp_fail;
+ /* PHY event notification can disturb reset and other recovery
+ * operations. Turn it off.
+ */
+ if (gscr[SATA_PMP_GSCR_FEAT_EN] & SATA_PMP_FEAT_NOTIFY) {
+ gscr[SATA_PMP_GSCR_FEAT_EN] &= ~SATA_PMP_FEAT_NOTIFY;
+
+ err_mask = sata_pmp_write(pmp_link, SATA_PMP_GSCR_FEAT_EN,
+ gscr[SATA_PMP_GSCR_FEAT_EN]);
+ if (err_mask) {
+ ata_link_printk(pmp_link, KERN_WARNING,
+ "failed to disable NOTIFY (err_mask=0x%x)\n",
+ err_mask);
+ goto pmp_fail;
+ }
+ }
+
/* handle disabled links */
rc = sata_pmp_eh_handle_disabled_links(ap);
if (rc)
@@ -923,10 +923,10 @@ static int sata_pmp_eh_recover(struct ata_port *ap)
/* enable notification */
if (pmp_dev->flags & ATA_DFLAG_AN) {
- pmp_dev->gscr[SATA_PMP_GSCR_FEAT_EN] |= SATA_PMP_FEAT_NOTIFY;
+ gscr[SATA_PMP_GSCR_FEAT_EN] |= SATA_PMP_FEAT_NOTIFY;
- err_mask = sata_pmp_write(pmp_dev->link, SATA_PMP_GSCR_FEAT_EN,
- pmp_dev->gscr[SATA_PMP_GSCR_FEAT_EN]);
+ err_mask = sata_pmp_write(pmp_link, SATA_PMP_GSCR_FEAT_EN,
+ gscr[SATA_PMP_GSCR_FEAT_EN]);
if (err_mask) {
ata_dev_printk(pmp_dev, KERN_ERR, "failed to write "
"PMP_FEAT_EN (Emask=0x%x)\n", err_mask);
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 3ce4392..aeb6e01 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -1082,12 +1082,6 @@ static unsigned int ata_scsi_start_stop_xlat(struct ata_queued_cmd *qc)
if (((cdb[4] >> 4) & 0xf) != 0)
goto invalid_fld; /* power conditions not supported */
- if (qc->dev->horkage & ATA_HORKAGE_SKIP_PM) {
- /* the device lacks PM support, finish without doing anything */
- scmd->result = SAM_STAT_GOOD;
- return 1;
- }
-
if (cdb[4] & 0x1) {
tf->nsect = 1; /* 1 sector, lba=0 */
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index fcabe46..0f3e659 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -177,11 +177,11 @@ static void ali_program_modes(struct ata_port *ap, struct ata_device *adev, stru
u8 udma;
if (t != NULL) {
- t->setup = FIT(t->setup, 1, 8) & 7;
- t->act8b = FIT(t->act8b, 1, 8) & 7;
- t->rec8b = FIT(t->rec8b, 1, 16) & 15;
- t->active = FIT(t->active, 1, 8) & 7;
- t->recover = FIT(t->recover, 1, 16) & 15;
+ t->setup = clamp_val(t->setup, 1, 8) & 7;
+ t->act8b = clamp_val(t->act8b, 1, 8) & 7;
+ t->rec8b = clamp_val(t->rec8b, 1, 16) & 15;
+ t->active = clamp_val(t->active, 1, 8) & 7;
+ t->recover = clamp_val(t->recover, 1, 16) & 15;
pci_write_config_byte(pdev, cas, t->setup);
pci_write_config_byte(pdev, cbt, (t->act8b << 4) | t->rec8b);
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index 26665c3..57dd00f 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -84,32 +84,32 @@ static void timing_setup(struct ata_port *ap, struct ata_device *adev, int offse
/* Configure the address set up timing */
pci_read_config_byte(pdev, offset + 0x0C, &t);
- t = (t & ~(3 << ((3 - dn) << 1))) | ((FIT(at.setup, 1, 4) - 1) << ((3 - dn) << 1));
+ t = (t & ~(3 << ((3 - dn) << 1))) | ((clamp_val(at.setup, 1, 4) - 1) << ((3 - dn) << 1));
pci_write_config_byte(pdev, offset + 0x0C , t);
/* Configure the 8bit I/O timing */
pci_write_config_byte(pdev, offset + 0x0E + (1 - (dn >> 1)),
- ((FIT(at.act8b, 1, 16) - 1) << 4) | (FIT(at.rec8b, 1, 16) - 1));
+ ((clamp_val(at.act8b, 1, 16) - 1) << 4) | (clamp_val(at.rec8b, 1, 16) - 1));
/* Drive timing */
pci_write_config_byte(pdev, offset + 0x08 + (3 - dn),
- ((FIT(at.active, 1, 16) - 1) << 4) | (FIT(at.recover, 1, 16) - 1));
+ ((clamp_val(at.active, 1, 16) - 1) << 4) | (clamp_val(at.recover, 1, 16) - 1));
switch (clock) {
case 1:
- t = at.udma ? (0xc0 | (FIT(at.udma, 2, 5) - 2)) : 0x03;
+ t = at.udma ? (0xc0 | (clamp_val(at.udma, 2, 5) - 2)) : 0x03;
break;
case 2:
- t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 2, 10)]) : 0x03;
+ t = at.udma ? (0xc0 | amd_cyc2udma[clamp_val(at.udma, 2, 10)]) : 0x03;
break;
case 3:
- t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 1, 10)]) : 0x03;
+ t = at.udma ? (0xc0 | amd_cyc2udma[clamp_val(at.udma, 1, 10)]) : 0x03;
break;
case 4:
- t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 1, 15)]) : 0x03;
+ t = at.udma ? (0xc0 | amd_cyc2udma[clamp_val(at.udma, 1, 15)]) : 0x03;
break;
default:
diff --git a/drivers/ata/pata_at32.c b/drivers/ata/pata_at32.c
index 5e10438..82fb6e2 100644
--- a/drivers/ata/pata_at32.c
+++ b/drivers/ata/pata_at32.c
@@ -291,8 +291,6 @@ static int __init pata_at32_probe(struct platform_device *pdev)
if (!info)
return -ENOMEM;
- memset(info, 0, sizeof(struct at32_ide_info));
-
info->irq = irq;
info->cs = board->cs;
diff --git a/drivers/ata/pata_bf54x.c b/drivers/ata/pata_bf54x.c
index 9ab8973..5551610 100644
--- a/drivers/ata/pata_bf54x.c
+++ b/drivers/ata/pata_bf54x.c
@@ -911,7 +911,10 @@ static void bfin_bmdma_start(struct ata_queued_cmd *qc)
/* Reset all transfer count */
ATAPI_SET_CONTROL(base, ATAPI_GET_CONTROL(base) | TFRCNT_RST);
- /* Set transfer length to buffer len */
+ /* Set ATAPI state machine contorl in terminate sequence */
+ ATAPI_SET_CONTROL(base, ATAPI_GET_CONTROL(base) | END_ON_TERM);
+
+ /* Set transfer length to buffer len */
for_each_sg(qc->sg, sg, qc->n_elem, si) {
ATAPI_SET_XFER_LEN(base, (sg_dma_len(sg) >> 1));
}
diff --git a/drivers/ata/pata_cypress.c b/drivers/ata/pata_cypress.c
index a9c3218..2ff6260 100644
--- a/drivers/ata/pata_cypress.c
+++ b/drivers/ata/pata_cypress.c
@@ -62,14 +62,14 @@ static void cy82c693_set_piomode(struct ata_port *ap, struct ata_device *adev)
return;
}
- time_16 = FIT(t.recover, 0, 15) | (FIT(t.active, 0, 15) << 4);
- time_8 = FIT(t.act8b, 0, 15) | (FIT(t.rec8b, 0, 15) << 4);
+ time_16 = clamp_val(t.recover, 0, 15) | (clamp_val(t.active, 0, 15) << 4);
+ time_8 = clamp_val(t.act8b, 0, 15) | (clamp_val(t.rec8b, 0, 15) << 4);
if (adev->devno == 0) {
pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr);
addr &= ~0x0F; /* Mask bits */
- addr |= FIT(t.setup, 0, 15);
+ addr |= clamp_val(t.setup, 0, 15);
pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr);
pci_write_config_byte(pdev, CY82_IDE_MASTER_IOR, time_16);
@@ -79,7 +79,7 @@ static void cy82c693_set_piomode(struct ata_port *ap, struct ata_device *adev)
pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr);
addr &= ~0xF0; /* Mask bits */
- addr |= (FIT(t.setup, 0, 15) << 4);
+ addr |= (clamp_val(t.setup, 0, 15) << 4);
pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr);
pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOR, time_16);
diff --git a/drivers/ata/pata_legacy.c b/drivers/ata/pata_legacy.c
index 7af4b29..fe7cc8e 100644
--- a/drivers/ata/pata_legacy.c
+++ b/drivers/ata/pata_legacy.c
@@ -343,8 +343,8 @@ static void ht6560a_set_piomode(struct ata_port *ap, struct ata_device *adev)
/* Get the timing data in cycles. For now play safe at 50Mhz */
ata_timing_compute(adev, adev->pio_mode, &t, 20000, 1000);
- active = FIT(t.active, 2, 15);
- recover = FIT(t.recover, 4, 15);
+ active = clamp_val(t.active, 2, 15);
+ recover = clamp_val(t.recover, 4, 15);
inb(0x3E6);
inb(0x3E6);
@@ -377,8 +377,8 @@ static void ht6560b_set_piomode(struct ata_port *ap, struct ata_device *adev)
/* Get the timing data in cycles. For now play safe at 50Mhz */
ata_timing_compute(adev, adev->pio_mode, &t, 20000, 1000);
- active = FIT(t.active, 2, 15);
- recover = FIT(t.recover, 2, 16);
+ active = clamp_val(t.active, 2, 15);
+ recover = clamp_val(t.recover, 2, 16);
recover &= 0x15;
inb(0x3E6);
@@ -462,9 +462,9 @@ static void opti82c611a_set_piomode(struct ata_port *ap,
ata_timing_merge(&t, &tp, &t, ATA_TIMING_SETUP);
}
- active = FIT(t.active, 2, 17) - 2;
- recover = FIT(t.recover, 1, 16) - 1;
- setup = FIT(t.setup, 1, 4) - 1;
+ active = clamp_val(t.active, 2, 17) - 2;
+ recover = clamp_val(t.recover, 1, 16) - 1;
+ setup = clamp_val(t.setup, 1, 4) - 1;
/* Select the right timing bank for write timing */
rc = ioread8(ap->ioaddr.lbal_addr);
@@ -541,9 +541,9 @@ static void opti82c46x_set_piomode(struct ata_port *ap, struct ata_device *adev)
ata_timing_merge(&t, &tp, &t, ATA_TIMING_SETUP);
}
- active = FIT(t.active, 2, 17) - 2;
- recover = FIT(t.recover, 1, 16) - 1;
- setup = FIT(t.setup, 1, 4) - 1;
+ active = clamp_val(t.active, 2, 17) - 2;
+ recover = clamp_val(t.recover, 1, 16) - 1;
+ setup = clamp_val(t.setup, 1, 4) - 1;
/* Select the right timing bank for write timing */
rc = ioread8(ap->ioaddr.lbal_addr);
@@ -624,11 +624,11 @@ static void qdi6500_set_piomode(struct ata_port *ap, struct ata_device *adev)
ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000);
if (ld_qdi->fast) {
- active = 8 - FIT(t.active, 1, 8);
- recovery = 18 - FIT(t.recover, 3, 18);
+ active = 8 - clamp_val(t.active, 1, 8);
+ recovery = 18 - clamp_val(t.recover, 3, 18);
} else {
- active = 9 - FIT(t.active, 2, 9);
- recovery = 15 - FIT(t.recover, 0, 15);
+ active = 9 - clamp_val(t.active, 2, 9);
+ recovery = 15 - clamp_val(t.recover, 0, 15);
}
timing = (recovery << 4) | active | 0x08;
@@ -658,11 +658,11 @@ static void qdi6580dp_set_piomode(struct ata_port *ap, struct ata_device *adev)
ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000);
if (ld_qdi->fast) {
- active = 8 - FIT(t.active, 1, 8);
- recovery = 18 - FIT(t.recover, 3, 18);
+ active = 8 - clamp_val(t.active, 1, 8);
+ recovery = 18 - clamp_val(t.recover, 3, 18);
} else {
- active = 9 - FIT(t.active, 2, 9);
- recovery = 15 - FIT(t.recover, 0, 15);
+ active = 9 - clamp_val(t.active, 2, 9);
+ recovery = 15 - clamp_val(t.recover, 0, 15);
}
timing = (recovery << 4) | active | 0x08;
@@ -695,11 +695,11 @@ static void qdi6580_set_piomode(struct ata_port *ap, struct ata_device *adev)
ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000);
if (ld_qdi->fast) {
- active = 8 - FIT(t.active, 1, 8);
- recovery = 18 - FIT(t.recover, 3, 18);
+ active = 8 - clamp_val(t.active, 1, 8);
+ recovery = 18 - clamp_val(t.recover, 3, 18);
} else {
- active = 9 - FIT(t.active, 2, 9);
- recovery = 15 - FIT(t.recover, 0, 15);
+ active = 9 - clamp_val(t.active, 2, 9);
+ recovery = 15 - clamp_val(t.recover, 0, 15);
}
timing = (recovery << 4) | active | 0x08;
ld_qdi->clock[adev->devno] = timing;
@@ -830,8 +830,8 @@ static void winbond_set_piomode(struct ata_port *ap, struct ata_device *adev)
else
ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000);
- active = (FIT(t.active, 3, 17) - 1) & 0x0F;
- recovery = (FIT(t.recover, 1, 15) + 1) & 0x0F;
+ active = (clamp_val(t.active, 3, 17) - 1) & 0x0F;
+ recovery = (clamp_val(t.recover, 1, 15) + 1) & 0x0F;
timing = (active << 4) | recovery;
winbond_writecfg(ld_winbond->timing, timing, reg);
@@ -842,7 +842,7 @@ static void winbond_set_piomode(struct ata_port *ap, struct ata_device *adev)
reg |= 0x08; /* FIFO off */
if (!ata_pio_need_iordy(adev))
reg |= 0x02; /* IORDY off */
- reg |= (FIT(t.setup, 0, 3) << 6);
+ reg |= (clamp_val(t.setup, 0, 3) << 6);
winbond_writecfg(ld_winbond->timing, timing + 1, reg);
}
diff --git a/drivers/ata/pata_ns87410.c b/drivers/ata/pata_ns87410.c
index 76d2455..be756b7 100644
--- a/drivers/ata/pata_ns87410.c
+++ b/drivers/ata/pata_ns87410.c
@@ -91,9 +91,9 @@ static void ns87410_set_piomode(struct ata_port *ap, struct ata_device *adev)
return;
}
- at.active = FIT(at.active, 2, 16) - 2;
- at.setup = FIT(at.setup, 1, 4) - 1;
- at.recover = FIT(at.recover, 1, 12) - 1;
+ at.active = clamp_val(at.active, 2, 16) - 2;
+ at.setup = clamp_val(at.setup, 1, 4) - 1;
+ at.recover = clamp_val(at.recover, 1, 12) - 1;
idetcr = (at.setup << 6) | (recoverbits[at.recover] << 3) | activebits[at.active];
diff --git a/drivers/ata/pata_ns87415.c b/drivers/ata/pata_ns87415.c
index ae92b00..e0aa7ea 100644
--- a/drivers/ata/pata_ns87415.c
+++ b/drivers/ata/pata_ns87415.c
@@ -66,8 +66,8 @@ static void ns87415_set_mode(struct ata_port *ap, struct ata_device *adev, u8 mo
ata_timing_compute(adev, adev->pio_mode, &t, T, 0);
- clocking = 17 - FIT(t.active, 2, 17);
- clocking |= (16 - FIT(t.recover, 1, 16)) << 4;
+ clocking = 17 - clamp_val(t.active, 2, 17);
+ clocking |= (16 - clamp_val(t.recover, 1, 16)) << 4;
/* Use the same timing for read and write bytes */
clocking |= (clocking << 8);
pci_write_config_word(dev, timing, clocking);
diff --git a/drivers/ata/pata_qdi.c b/drivers/ata/pata_qdi.c
index bf45cf0..97e5b09 100644
--- a/drivers/ata/pata_qdi.c
+++ b/drivers/ata/pata_qdi.c
@@ -60,11 +60,11 @@ static void qdi6500_set_piomode(struct ata_port *ap, struct ata_device *adev)
ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000);
if (qdi->fast) {
- active = 8 - FIT(t.active, 1, 8);
- recovery = 18 - FIT(t.recover, 3, 18);
+ active = 8 - clamp_val(t.active, 1, 8);
+ recovery = 18 - clamp_val(t.recover, 3, 18);
} else {
- active = 9 - FIT(t.active, 2, 9);
- recovery = 15 - FIT(t.recover, 0, 15);
+ active = 9 - clamp_val(t.active, 2, 9);
+ recovery = 15 - clamp_val(t.recover, 0, 15);
}
timing = (recovery << 4) | active | 0x08;
@@ -84,11 +84,11 @@ static void qdi6580_set_piomode(struct ata_port *ap, struct ata_device *adev)
ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000);
if (qdi->fast) {
- active = 8 - FIT(t.active, 1, 8);
- recovery = 18 - FIT(t.recover, 3, 18);
+ active = 8 - clamp_val(t.active, 1, 8);
+ recovery = 18 - clamp_val(t.recover, 3, 18);
} else {
- active = 9 - FIT(t.active, 2, 9);
- recovery = 15 - FIT(t.recover, 0, 15);
+ active = 9 - clamp_val(t.active, 2, 9);
+ recovery = 15 - clamp_val(t.recover, 0, 15);
}
timing = (recovery << 4) | active | 0x08;
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index 70d94fb..69877bd 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -216,7 +216,7 @@ static int sl82c105_qc_defer(struct ata_queued_cmd *qc)
struct ata_port *alt = host->ports[1 ^ qc->ap->port_no];
int rc;
- /* First apply the usual rules */
+ /* First apply the usual rules */
rc = ata_std_qc_defer(qc);
if (rc != 0)
return rc;
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 2fea6cb..708ed14 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -259,15 +259,15 @@ static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, int mo
pci_read_config_byte(pdev, 0x4C, &setup);
setup &= ~(3 << shift);
- setup |= FIT(t.setup, 1, 4) << shift; /* 1,4 or 1,4 - 1 FIXME */
+ setup |= clamp_val(t.setup, 1, 4) << shift; /* 1,4 or 1,4 - 1 FIXME */
pci_write_config_byte(pdev, 0x4C, setup);
}
/* Load the PIO mode bits */
pci_write_config_byte(pdev, 0x4F - ap->port_no,
- ((FIT(t.act8b, 1, 16) - 1) << 4) | (FIT(t.rec8b, 1, 16) - 1));
+ ((clamp_val(t.act8b, 1, 16) - 1) << 4) | (clamp_val(t.rec8b, 1, 16) - 1));
pci_write_config_byte(pdev, 0x48 + offset,
- ((FIT(t.active, 1, 16) - 1) << 4) | (FIT(t.recover, 1, 16) - 1));
+ ((clamp_val(t.active, 1, 16) - 1) << 4) | (clamp_val(t.recover, 1, 16) - 1));
/* Load the UDMA bits according to type */
switch(udma_type) {
@@ -275,16 +275,16 @@ static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, int mo
/* BUG() ? */
/* fall through */
case 33:
- ut = t.udma ? (0xe0 | (FIT(t.udma, 2, 5) - 2)) : 0x03;
+ ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 5) - 2)) : 0x03;
break;
case 66:
- ut = t.udma ? (0xe8 | (FIT(t.udma, 2, 9) - 2)) : 0x0f;
+ ut = t.udma ? (0xe8 | (clamp_val(t.udma, 2, 9) - 2)) : 0x0f;
break;
case 100:
- ut = t.udma ? (0xe0 | (FIT(t.udma, 2, 9) - 2)) : 0x07;
+ ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07;
break;
case 133:
- ut = t.udma ? (0xe0 | (FIT(t.udma, 2, 9) - 2)) : 0x07;
+ ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07;
break;
}
diff --git a/drivers/ata/pata_winbond.c b/drivers/ata/pata_winbond.c
index 6e52a35..474528f 100644
--- a/drivers/ata/pata_winbond.c
+++ b/drivers/ata/pata_winbond.c
@@ -75,8 +75,8 @@ static void winbond_set_piomode(struct ata_port *ap, struct ata_device *adev)
else
ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000);
- active = (FIT(t.active, 3, 17) - 1) & 0x0F;
- recovery = (FIT(t.recover, 1, 15) + 1) & 0x0F;
+ active = (clamp_val(t.active, 3, 17) - 1) & 0x0F;
+ recovery = (clamp_val(t.recover, 1, 15) + 1) & 0x0F;
timing = (active << 4) | recovery;
winbond_writecfg(winbond->config, timing, reg);
@@ -87,7 +87,7 @@ static void winbond_set_piomode(struct ata_port *ap, struct ata_device *adev)
reg |= 0x08; /* FIFO off */
if (!ata_pio_need_iordy(adev))
reg |= 0x02; /* IORDY off */
- reg |= (FIT(t.setup, 0, 3) << 6);
+ reg |= (clamp_val(t.setup, 0, 3) << 6);
winbond_writecfg(winbond->config, timing + 1, reg);
}
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index bb73b22..fb81f0c 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -72,7 +72,7 @@
#include <linux/libata.h>
#define DRV_NAME "sata_mv"
-#define DRV_VERSION "1.20"
+#define DRV_VERSION "1.21"
enum {
/* BAR's are enumerated in terms of pci_resource_start() terms */
@@ -128,8 +128,13 @@ enum {
MV_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI |
ATA_FLAG_PIO_POLLING,
+
MV_6XXX_FLAGS = MV_FLAG_IRQ_COALESCE,
+ MV_GENIIE_FLAGS = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
+ ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
+ ATA_FLAG_NCQ | ATA_FLAG_AN,
+
CRQB_FLAG_READ = (1 << 0),
CRQB_TAG_SHIFT = 1,
CRQB_IOID_SHIFT = 6, /* CRQB Gen-II/IIE IO Id shift */
@@ -197,13 +202,6 @@ enum {
HC_MAIN_RSVD = (0x7f << 25), /* bits 31-25 */
HC_MAIN_RSVD_5 = (0x1fff << 19), /* bits 31-19 */
HC_MAIN_RSVD_SOC = (0x3fffffb << 6), /* bits 31-9, 7-6 */
- HC_MAIN_MASKED_IRQS = (TRAN_LO_DONE | TRAN_HI_DONE |
- PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE |
- PORTS_0_7_COAL_DONE | GPIO_INT | TWSI_INT |
- HC_MAIN_RSVD),
- HC_MAIN_MASKED_IRQS_5 = (PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE |
- HC_MAIN_RSVD_5),
- HC_MAIN_MASKED_IRQS_SOC = (PORTS_0_3_COAL_DONE | HC_MAIN_RSVD_SOC),
/* SATAHC registers */
HC_CFG_OFS = 0,
@@ -221,6 +219,7 @@ enum {
SATA_STATUS_OFS = 0x300, /* ctrl, err regs follow status */
SATA_ACTIVE_OFS = 0x350,
SATA_FIS_IRQ_CAUSE_OFS = 0x364,
+ SATA_FIS_IRQ_AN = (1 << 9), /* async notification */
LTMODE_OFS = 0x30c,
LTMODE_BIT8 = (1 << 8), /* unknown, but necessary */
@@ -459,6 +458,7 @@ struct mv_port_signal {
struct mv_host_priv {
u32 hp_flags;
+ u32 main_irq_mask;
struct mv_port_signal signal[8];
const struct mv_hw_ops *ops;
int n_ports;
@@ -640,25 +640,19 @@ static const struct ata_port_info mv_port_info[] = {
.port_ops = &mv6_ops,
},
{ /* chip_6042 */
- .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ,
+ .flags = MV_GENIIE_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
{ /* chip_7042 */
- .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ,
+ .flags = MV_GENIIE_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
{ /* chip_soc */
- .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ | MV_FLAG_SOC,
+ .flags = MV_GENIIE_FLAGS | MV_FLAG_SOC,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
@@ -844,6 +838,33 @@ static void mv_set_edma_ptrs(void __iomem *port_mmio,
port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
}
+static void mv_set_main_irq_mask(struct ata_host *host,
+ u32 disable_bits, u32 enable_bits)
+{
+ struct mv_host_priv *hpriv = host->private_data;
+ u32 old_mask, new_mask;
+
+ old_mask = hpriv->main_irq_mask;
+ new_mask = (old_mask & ~disable_bits) | enable_bits;
+ if (new_mask != old_mask) {
+ hpriv->main_irq_mask = new_mask;
+ writelfl(new_mask, hpriv->main_irq_mask_addr);
+ }
+}
+
+static void mv_enable_port_irqs(struct ata_port *ap,
+ unsigned int port_bits)
+{
+ unsigned int shift, hardport, port = ap->port_no;
+ u32 disable_bits, enable_bits;
+
+ MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport);
+
+ disable_bits = (DONE_IRQ | ERR_IRQ) << shift;
+ enable_bits = port_bits << shift;
+ mv_set_main_irq_mask(ap->host, disable_bits, enable_bits);
+}
+
/**
* mv_start_dma - Enable eDMA engine
* @base: port base address
@@ -886,9 +907,11 @@ static void mv_start_dma(struct ata_port *ap, void __iomem *port_mmio,
mv_edma_cfg(ap, want_ncq);
/* clear FIS IRQ Cause */
- writelfl(0, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
+ if (IS_GEN_IIE(hpriv))
+ writelfl(0, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
mv_set_edma_ptrs(port_mmio, hpriv, pp);
+ mv_enable_port_irqs(ap, DONE_IRQ|ERR_IRQ);
writelfl(EDMA_EN, port_mmio + EDMA_CMD_OFS);
pp->pp_flags |= MV_PP_FLAG_EDMA_EN;
@@ -1341,6 +1364,7 @@ out_port_free_dma_mem:
static void mv_port_stop(struct ata_port *ap)
{
mv_stop_edma(ap);
+ mv_enable_port_irqs(ap, 0);
mv_port_free_dma_mem(ap);
}
@@ -1582,6 +1606,7 @@ static unsigned int mv_qc_issue(struct ata_queued_cmd *qc)
* shadow block, etc registers.
*/
mv_stop_edma(ap);
+ mv_enable_port_irqs(ap, ERR_IRQ);
mv_pmp_select(ap, qc->dev->link->pmp);
return ata_sff_qc_issue(qc);
}
@@ -1670,6 +1695,18 @@ static void mv_pmp_eh_prep(struct ata_port *ap, unsigned int pmp_map)
}
}
+static int mv_req_q_empty(struct ata_port *ap)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+ u32 in_ptr, out_ptr;
+
+ in_ptr = (readl(port_mmio + EDMA_REQ_Q_IN_PTR_OFS)
+ >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
+ out_ptr = (readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS)
+ >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
+ return (in_ptr == out_ptr); /* 1 == queue_is_empty */
+}
+
static int mv_handle_fbs_ncq_dev_err(struct ata_port *ap)
{
struct mv_port_priv *pp = ap->private_data;
@@ -1703,7 +1740,7 @@ static int mv_handle_fbs_ncq_dev_err(struct ata_port *ap)
ap->qc_active, failed_links,
ap->nr_active_links);
- if (ap->nr_active_links <= failed_links) {
+ if (ap->nr_active_links <= failed_links && mv_req_q_empty(ap)) {
mv_process_crpb_entries(ap, pp);
mv_stop_edma(ap);
mv_eh_freeze(ap);
@@ -1812,6 +1849,7 @@ static void mv_err_intr(struct ata_port *ap)
{
void __iomem *port_mmio = mv_ap_base(ap);
u32 edma_err_cause, eh_freeze_mask, serr = 0;
+ u32 fis_cause = 0;
struct mv_port_priv *pp = ap->private_data;
struct mv_host_priv *hpriv = ap->host->private_data;
unsigned int action = 0, err_mask = 0;
@@ -1821,16 +1859,19 @@ static void mv_err_intr(struct ata_port *ap)
/*
* Read and clear the SError and err_cause bits.
+ * For GenIIe, if EDMA_ERR_TRANS_IRQ_7 is set, we also must read/clear
+ * the FIS_IRQ_CAUSE register before clearing edma_err_cause.
*/
sata_scr_read(&ap->link, SCR_ERROR, &serr);
sata_scr_write_flush(&ap->link, SCR_ERROR, serr);
edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+ if (IS_GEN_IIE(hpriv) && (edma_err_cause & EDMA_ERR_TRANS_IRQ_7)) {
+ fis_cause = readl(port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
+ writelfl(~fis_cause, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
+ }
writelfl(~edma_err_cause, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
- ata_port_printk(ap, KERN_INFO, "%s: err_cause=%08x pp_flags=0x%x\n",
- __func__, edma_err_cause, pp->pp_flags);
-
if (edma_err_cause & EDMA_ERR_DEV) {
/*
* Device errors during FIS-based switching operation
@@ -1844,6 +1885,18 @@ static void mv_err_intr(struct ata_port *ap)
ata_ehi_clear_desc(ehi);
ata_ehi_push_desc(ehi, "edma_err_cause=%08x pp_flags=%08x",
edma_err_cause, pp->pp_flags);
+
+ if (IS_GEN_IIE(hpriv) && (edma_err_cause & EDMA_ERR_TRANS_IRQ_7)) {
+ ata_ehi_push_desc(ehi, "fis_cause=%08x", fis_cause);
+ if (fis_cause & SATA_FIS_IRQ_AN) {
+ u32 ec = edma_err_cause &
+ ~(EDMA_ERR_TRANS_IRQ_7 | EDMA_ERR_IRQ_TRANSIENT);
+ sata_async_notification(ap);
+ if (!ec)
+ return; /* Just an AN; no need for the nukes */
+ ata_ehi_push_desc(ehi, "SDB notify");
+ }
+ }
/*
* All generations share these EDMA error cause bits:
*/
@@ -2162,20 +2215,20 @@ static irqreturn_t mv_interrupt(int irq, void *dev_instance)
struct ata_host *host = dev_instance;
struct mv_host_priv *hpriv = host->private_data;
unsigned int handled = 0;
- u32 main_irq_cause, main_irq_mask;
+ u32 main_irq_cause, pending_irqs;
spin_lock(&host->lock);
main_irq_cause = readl(hpriv->main_irq_cause_addr);
- main_irq_mask = readl(hpriv->main_irq_mask_addr);
+ pending_irqs = main_irq_cause & hpriv->main_irq_mask;
/*
* Deal with cases where we either have nothing pending, or have read
* a bogus register value which can indicate HW removal or PCI fault.
*/
- if ((main_irq_cause & main_irq_mask) && (main_irq_cause != 0xffffffffU)) {
- if (unlikely((main_irq_cause & PCI_ERR) && HAS_PCI(host)))
+ if (pending_irqs && main_irq_cause != 0xffffffffU) {
+ if (unlikely((pending_irqs & PCI_ERR) && HAS_PCI(host)))
handled = mv_pci_error(host, hpriv->base);
else
- handled = mv_host_intr(host, main_irq_cause);
+ handled = mv_host_intr(host, pending_irqs);
}
spin_unlock(&host->lock);
return IRQ_RETVAL(handled);
@@ -2373,7 +2426,6 @@ static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio)
ZERO(MV_PCI_DISC_TIMER);
ZERO(MV_PCI_MSI_TRIGGER);
writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT_OFS);
- ZERO(PCI_HC_MAIN_IRQ_MASK_OFS);
ZERO(MV_PCI_SERR_MASK);
ZERO(hpriv->irq_cause_ofs);
ZERO(hpriv->irq_mask_ofs);
@@ -2728,6 +2780,7 @@ static int mv_hardreset(struct ata_link *link, unsigned int *class,
rc = sata_link_hardreset(link, timing, deadline + extra,
&online, NULL);
+ rc = online ? -EAGAIN : rc;
if (rc)
return rc;
sata_scr_read(link, SCR_STATUS, &sstatus);
@@ -2744,32 +2797,18 @@ static int mv_hardreset(struct ata_link *link, unsigned int *class,
static void mv_eh_freeze(struct ata_port *ap)
{
- struct mv_host_priv *hpriv = ap->host->private_data;
- unsigned int shift, hardport, port = ap->port_no;
- u32 main_irq_mask;
-
- /* FIXME: handle coalescing completion events properly */
-
mv_stop_edma(ap);
- MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport);
-
- /* disable assertion of portN err, done events */
- main_irq_mask = readl(hpriv->main_irq_mask_addr);
- main_irq_mask &= ~((DONE_IRQ | ERR_IRQ) << shift);
- writelfl(main_irq_mask, hpriv->main_irq_mask_addr);
+ mv_enable_port_irqs(ap, 0);
}
static void mv_eh_thaw(struct ata_port *ap)
{
struct mv_host_priv *hpriv = ap->host->private_data;
- unsigned int shift, hardport, port = ap->port_no;
+ unsigned int port = ap->port_no;
+ unsigned int hardport = mv_hardport_from_port(port);
void __iomem *hc_mmio = mv_hc_base_from_port(hpriv->base, port);
void __iomem *port_mmio = mv_ap_base(ap);
- u32 main_irq_mask, hc_irq_cause;
-
- /* FIXME: handle coalescing completion events properly */
-
- MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport);
+ u32 hc_irq_cause;
/* clear EDMA errors on this port */
writel(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
@@ -2779,10 +2818,7 @@ static void mv_eh_thaw(struct ata_port *ap)
hc_irq_cause &= ~((DEV_IRQ | DMA_IRQ) << hardport);
writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
- /* enable assertion of portN err, done events */
- main_irq_mask = readl(hpriv->main_irq_mask_addr);
- main_irq_mask |= ((DONE_IRQ | ERR_IRQ) << shift);
- writelfl(main_irq_mask, hpriv->main_irq_mask_addr);
+ mv_enable_port_irqs(ap, ERR_IRQ);
}
/**
@@ -3035,7 +3071,7 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
}
/* global interrupt mask: 0 == mask everything */
- writel(0, hpriv->main_irq_mask_addr);
+ mv_set_main_irq_mask(host, ~0, 0);
n_hc = mv_get_hc_count(host->ports[0]->flags);
@@ -3083,25 +3119,12 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
/* and unmask interrupt generation for host regs */
writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_ofs);
- if (IS_GEN_I(hpriv))
- writelfl(~HC_MAIN_MASKED_IRQS_5,
- hpriv->main_irq_mask_addr);
- else
- writelfl(~HC_MAIN_MASKED_IRQS,
- hpriv->main_irq_mask_addr);
-
- VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x "
- "PCI int cause/mask=0x%08x/0x%08x\n",
- readl(hpriv->main_irq_cause_addr),
- readl(hpriv->main_irq_mask_addr),
- readl(mmio + hpriv->irq_cause_ofs),
- readl(mmio + hpriv->irq_mask_ofs));
- } else {
- writelfl(~HC_MAIN_MASKED_IRQS_SOC,
- hpriv->main_irq_mask_addr);
- VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x\n",
- readl(hpriv->main_irq_cause_addr),
- readl(hpriv->main_irq_mask_addr));
+
+ /*
+ * enable only global host interrupts for now.
+ * The per-port interrupts get done later as ports are set up.
+ */
+ mv_set_main_irq_mask(host, 0, PCI_ERR);
}
done:
return rc;
diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c
index 5a10dc5..030665b 100644
--- a/drivers/ata/sata_promise.c
+++ b/drivers/ata/sata_promise.c
@@ -53,7 +53,15 @@ enum {
PDC_MMIO_BAR = 3,
PDC_MAX_PRD = LIBATA_MAX_PRD - 1, /* -1 for ASIC PRD bug workaround */
- /* register offsets */
+ /* host register offsets (from host->iomap[PDC_MMIO_BAR]) */
+ PDC_INT_SEQMASK = 0x40, /* Mask of asserted SEQ INTs */
+ PDC_FLASH_CTL = 0x44, /* Flash control register */
+ PDC_SATA_PLUG_CSR = 0x6C, /* SATA Plug control/status reg */
+ PDC2_SATA_PLUG_CSR = 0x60, /* SATAII Plug control/status reg */
+ PDC_TBG_MODE = 0x41C, /* TBG mode (not SATAII) */
+ PDC_SLEW_CTL = 0x470, /* slew rate control reg (not SATAII) */
+
+ /* per-port ATA register offsets (from ap->ioaddr.cmd_addr) */
PDC_FEATURE = 0x04, /* Feature/Error reg (per port) */
PDC_SECTOR_COUNT = 0x08, /* Sector count reg (per port) */
PDC_SECTOR_NUMBER = 0x0C, /* Sector number reg (per port) */
@@ -63,14 +71,11 @@ enum {
PDC_COMMAND = 0x1C, /* Command/status reg (per port) */
PDC_ALTSTATUS = 0x38, /* Alternate-status/device-control reg (per port) */
PDC_PKT_SUBMIT = 0x40, /* Command packet pointer addr */
- PDC_INT_SEQMASK = 0x40, /* Mask of asserted SEQ INTs */
- PDC_FLASH_CTL = 0x44, /* Flash control register */
PDC_GLOBAL_CTL = 0x48, /* Global control/status (per port) */
PDC_CTLSTAT = 0x60, /* IDE control and status (per port) */
- PDC_SATA_PLUG_CSR = 0x6C, /* SATA Plug control/status reg */
- PDC2_SATA_PLUG_CSR = 0x60, /* SATAII Plug control/status reg */
- PDC_TBG_MODE = 0x41C, /* TBG mode (not SATAII) */
- PDC_SLEW_CTL = 0x470, /* slew rate control reg (not SATAII) */
+
+ /* per-port SATA register offsets (from ap->ioaddr.scr_addr) */
+ PDC_PHYMODE4 = 0x14,
/* PDC_GLOBAL_CTL bit definitions */
PDC_PH_ERR = (1 << 8), /* PCI error while loading packet */
@@ -134,7 +139,7 @@ struct pdc_port_priv {
static int pdc_sata_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val);
static int pdc_sata_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val);
-static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
+static int pdc_ata_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
static int pdc_common_port_start(struct ata_port *ap);
static int pdc_sata_port_start(struct ata_port *ap);
static void pdc_qc_prep(struct ata_queued_cmd *qc);
@@ -332,12 +337,12 @@ static int pdc_sata_port_start(struct ata_port *ap)
/* fix up PHYMODE4 align timing */
if (ap->flags & PDC_FLAG_GEN_II) {
- void __iomem *mmio = ap->ioaddr.scr_addr;
+ void __iomem *sata_mmio = ap->ioaddr.scr_addr;
unsigned int tmp;
- tmp = readl(mmio + 0x014);
+ tmp = readl(sata_mmio + PDC_PHYMODE4);
tmp = (tmp & ~3) | 1; /* set bits 1:0 = 0:1 */
- writel(tmp, mmio + 0x014);
+ writel(tmp, sata_mmio + PDC_PHYMODE4);
}
return 0;
@@ -345,32 +350,32 @@ static int pdc_sata_port_start(struct ata_port *ap)
static void pdc_reset_port(struct ata_port *ap)
{
- void __iomem *mmio = ap->ioaddr.cmd_addr + PDC_CTLSTAT;
+ void __iomem *ata_ctlstat_mmio = ap->ioaddr.cmd_addr + PDC_CTLSTAT;
unsigned int i;
u32 tmp;
for (i = 11; i > 0; i--) {
- tmp = readl(mmio);
+ tmp = readl(ata_ctlstat_mmio);
if (tmp & PDC_RESET)
break;
udelay(100);
tmp |= PDC_RESET;
- writel(tmp, mmio);
+ writel(tmp, ata_ctlstat_mmio);
}
tmp &= ~PDC_RESET;
- writel(tmp, mmio);
- readl(mmio); /* flush */
+ writel(tmp, ata_ctlstat_mmio);
+ readl(ata_ctlstat_mmio); /* flush */
}
static int pdc_pata_cable_detect(struct ata_port *ap)
{
u8 tmp;
- void __iomem *mmio = ap->ioaddr.cmd_addr + PDC_CTLSTAT + 0x03;
+ void __iomem *ata_mmio = ap->ioaddr.cmd_addr;
- tmp = readb(mmio);
+ tmp = readb(ata_mmio + PDC_CTLSTAT + 3);
if (tmp & 0x01)
return ATA_CBL_PATA40;
return ATA_CBL_PATA80;
@@ -557,31 +562,25 @@ static void pdc_qc_prep(struct ata_queued_cmd *qc)
switch (qc->tf.protocol) {
case ATA_PROT_DMA:
pdc_fill_sg(qc);
- /* fall through */
-
+ /*FALLTHROUGH*/
case ATA_PROT_NODATA:
i = pdc_pkt_header(&qc->tf, qc->ap->prd_dma,
qc->dev->devno, pp->pkt);
-
if (qc->tf.flags & ATA_TFLAG_LBA48)
i = pdc_prep_lba48(&qc->tf, pp->pkt, i);
else
i = pdc_prep_lba28(&qc->tf, pp->pkt, i);
-
pdc_pkt_footer(&qc->tf, pp->pkt, i);
break;
-
case ATAPI_PROT_PIO:
pdc_fill_sg(qc);
break;
-
case ATAPI_PROT_DMA:
pdc_fill_sg(qc);
/*FALLTHROUGH*/
case ATAPI_PROT_NODATA:
pdc_atapi_pkt(qc);
break;
-
default:
break;
}
@@ -611,7 +610,7 @@ static unsigned int pdc_sata_ata_port_to_ata_no(const struct ata_port *ap)
unsigned int nr_ports = pdc_sata_nr_ports(ap);
unsigned int i;
- for(i = 0; i < nr_ports && host->ports[i] != ap; ++i)
+ for (i = 0; i < nr_ports && host->ports[i] != ap; ++i)
;
BUG_ON(i >= nr_ports);
return pdc_port_no_to_ata_no(i, pdc_is_sataii_tx4(ap->flags));
@@ -624,14 +623,14 @@ static unsigned int pdc_sata_hotplug_offset(const struct ata_port *ap)
static void pdc_freeze(struct ata_port *ap)
{
- void __iomem *mmio = ap->ioaddr.cmd_addr;
+ void __iomem *ata_mmio = ap->ioaddr.cmd_addr;
u32 tmp;
- tmp = readl(mmio + PDC_CTLSTAT);
+ tmp = readl(ata_mmio + PDC_CTLSTAT);
tmp |= PDC_IRQ_DISABLE;
tmp &= ~PDC_DMA_ENABLE;
- writel(tmp, mmio + PDC_CTLSTAT);
- readl(mmio + PDC_CTLSTAT); /* flush */
+ writel(tmp, ata_mmio + PDC_CTLSTAT);
+ readl(ata_mmio + PDC_CTLSTAT); /* flush */
}
static void pdc_sata_freeze(struct ata_port *ap)
@@ -659,17 +658,17 @@ static void pdc_sata_freeze(struct ata_port *ap)
static void pdc_thaw(struct ata_port *ap)
{
- void __iomem *mmio = ap->ioaddr.cmd_addr;
+ void __iomem *ata_mmio = ap->ioaddr.cmd_addr;
u32 tmp;
/* clear IRQ */
- readl(mmio + PDC_INT_SEQMASK);
+ readl(ata_mmio + PDC_COMMAND);
/* turn IRQ back on */
- tmp = readl(mmio + PDC_CTLSTAT);
+ tmp = readl(ata_mmio + PDC_CTLSTAT);
tmp &= ~PDC_IRQ_DISABLE;
- writel(tmp, mmio + PDC_CTLSTAT);
- readl(mmio + PDC_CTLSTAT); /* flush */
+ writel(tmp, ata_mmio + PDC_CTLSTAT);
+ readl(ata_mmio + PDC_CTLSTAT); /* flush */
}
static void pdc_sata_thaw(struct ata_port *ap)
@@ -743,11 +742,11 @@ static void pdc_error_intr(struct ata_port *ap, struct ata_queued_cmd *qc,
ata_port_abort(ap);
}
-static inline unsigned int pdc_host_intr(struct ata_port *ap,
- struct ata_queued_cmd *qc)
+static unsigned int pdc_host_intr(struct ata_port *ap,
+ struct ata_queued_cmd *qc)
{
unsigned int handled = 0;
- void __iomem *port_mmio = ap->ioaddr.cmd_addr;
+ void __iomem *ata_mmio = ap->ioaddr.cmd_addr;
u32 port_status, err_mask;
err_mask = PDC_ERR_MASK;
@@ -755,7 +754,7 @@ static inline unsigned int pdc_host_intr(struct ata_port *ap,
err_mask &= ~PDC1_ERR_MASK;
else
err_mask &= ~PDC2_ERR_MASK;
- port_status = readl(port_mmio + PDC_GLOBAL_CTL);
+ port_status = readl(ata_mmio + PDC_GLOBAL_CTL);
if (unlikely(port_status & err_mask)) {
pdc_error_intr(ap, qc, port_status, err_mask);
return 1;
@@ -770,7 +769,6 @@ static inline unsigned int pdc_host_intr(struct ata_port *ap,
ata_qc_complete(qc);
handled = 1;
break;
-
default:
ap->stats.idle_irq++;
break;
@@ -781,10 +779,9 @@ static inline unsigned int pdc_host_intr(struct ata_port *ap,
static void pdc_irq_clear(struct ata_port *ap)
{
- struct ata_host *host = ap->host;
- void __iomem *mmio = host->iomap[PDC_MMIO_BAR];
+ void __iomem *ata_mmio = ap->ioaddr.cmd_addr;
- readl(mmio + PDC_INT_SEQMASK);
+ readl(ata_mmio + PDC_COMMAND);
}
static irqreturn_t pdc_interrupt(int irq, void *dev_instance)
@@ -794,7 +791,7 @@ static irqreturn_t pdc_interrupt(int irq, void *dev_instance)
u32 mask = 0;
unsigned int i, tmp;
unsigned int handled = 0;
- void __iomem *mmio_base;
+ void __iomem *host_mmio;
unsigned int hotplug_offset, ata_no;
u32 hotplug_status;
int is_sataii_tx4;
@@ -806,7 +803,7 @@ static irqreturn_t pdc_interrupt(int irq, void *dev_instance)
return IRQ_NONE;
}
- mmio_base = host->iomap[PDC_MMIO_BAR];
+ host_mmio = host->iomap[PDC_MMIO_BAR];
spin_lock(&host->lock);
@@ -815,26 +812,26 @@ static irqreturn_t pdc_interrupt(int irq, void *dev_instance)
hotplug_offset = PDC2_SATA_PLUG_CSR;
else
hotplug_offset = PDC_SATA_PLUG_CSR;
- hotplug_status = readl(mmio_base + hotplug_offset);
+ hotplug_status = readl(host_mmio + hotplug_offset);
if (hotplug_status & 0xff)
- writel(hotplug_status | 0xff, mmio_base + hotplug_offset);
+ writel(hotplug_status | 0xff, host_mmio + hotplug_offset);
hotplug_status &= 0xff; /* clear uninteresting bits */
/* reading should also clear interrupts */
- mask = readl(mmio_base + PDC_INT_SEQMASK);
+ mask = readl(host_mmio + PDC_INT_SEQMASK);
if (mask == 0xffffffff && hotplug_status == 0) {
VPRINTK("QUICK EXIT 2\n");
goto done_irq;
}
- mask &= 0xffff; /* only 16 tags possible */
+ mask &= 0xffff; /* only 16 SEQIDs possible */
if (mask == 0 && hotplug_status == 0) {
VPRINTK("QUICK EXIT 3\n");
goto done_irq;
}
- writel(mask, mmio_base + PDC_INT_SEQMASK);
+ writel(mask, host_mmio + PDC_INT_SEQMASK);
is_sataii_tx4 = pdc_is_sataii_tx4(host->ports[0]->flags);
@@ -875,23 +872,24 @@ done_irq:
return IRQ_RETVAL(handled);
}
-static inline void pdc_packet_start(struct ata_queued_cmd *qc)
+static void pdc_packet_start(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct pdc_port_priv *pp = ap->private_data;
- void __iomem *mmio = ap->host->iomap[PDC_MMIO_BAR];
+ void __iomem *host_mmio = ap->host->iomap[PDC_MMIO_BAR];
+ void __iomem *ata_mmio = ap->ioaddr.cmd_addr;
unsigned int port_no = ap->port_no;
u8 seq = (u8) (port_no + 1);
VPRINTK("ENTER, ap %p\n", ap);
- writel(0x00000001, mmio + (seq * 4));
- readl(mmio + (seq * 4)); /* flush */
+ writel(0x00000001, host_mmio + (seq * 4));
+ readl(host_mmio + (seq * 4)); /* flush */
pp->pkt[2] = seq;
wmb(); /* flush PRD, pkt writes */
- writel(pp->pkt_dma, ap->ioaddr.cmd_addr + PDC_PKT_SUBMIT);
- readl(ap->ioaddr.cmd_addr + PDC_PKT_SUBMIT); /* flush */
+ writel(pp->pkt_dma, ata_mmio + PDC_PKT_SUBMIT);
+ readl(ata_mmio + PDC_PKT_SUBMIT); /* flush */
}
static unsigned int pdc_qc_issue(struct ata_queued_cmd *qc)
@@ -909,11 +907,9 @@ static unsigned int pdc_qc_issue(struct ata_queued_cmd *qc)
case ATA_PROT_DMA:
pdc_packet_start(qc);
return 0;
-
default:
break;
}
-
return ata_sff_qc_issue(qc);
}
@@ -987,7 +983,7 @@ static void pdc_ata_setup_port(struct ata_port *ap,
static void pdc_host_init(struct ata_host *host)
{
- void __iomem *mmio = host->iomap[PDC_MMIO_BAR];
+ void __iomem *host_mmio = host->iomap[PDC_MMIO_BAR];
int is_gen2 = host->ports[0]->flags & PDC_FLAG_GEN_II;
int hotplug_offset;
u32 tmp;
@@ -1004,38 +1000,38 @@ static void pdc_host_init(struct ata_host *host)
*/
/* enable BMR_BURST, maybe change FIFO_SHD to 8 dwords */
- tmp = readl(mmio + PDC_FLASH_CTL);
+ tmp = readl(host_mmio + PDC_FLASH_CTL);
tmp |= 0x02000; /* bit 13 (enable bmr burst) */
if (!is_gen2)
tmp |= 0x10000; /* bit 16 (fifo threshold at 8 dw) */
- writel(tmp, mmio + PDC_FLASH_CTL);
+ writel(tmp, host_mmio + PDC_FLASH_CTL);
/* clear plug/unplug flags for all ports */
- tmp = readl(mmio + hotplug_offset);
- writel(tmp | 0xff, mmio + hotplug_offset);
+ tmp = readl(host_mmio + hotplug_offset);
+ writel(tmp | 0xff, host_mmio + hotplug_offset);
/* unmask plug/unplug ints */
- tmp = readl(mmio + hotplug_offset);
- writel(tmp & ~0xff0000, mmio + hotplug_offset);
+ tmp = readl(host_mmio + hotplug_offset);
+ writel(tmp & ~0xff0000, host_mmio + hotplug_offset);
/* don't initialise TBG or SLEW on 2nd generation chips */
if (is_gen2)
return;
/* reduce TBG clock to 133 Mhz. */
- tmp = readl(mmio + PDC_TBG_MODE);
+ tmp = readl(host_mmio + PDC_TBG_MODE);
tmp &= ~0x30000; /* clear bit 17, 16*/
tmp |= 0x10000; /* set bit 17:16 = 0:1 */
- writel(tmp, mmio + PDC_TBG_MODE);
+ writel(tmp, host_mmio + PDC_TBG_MODE);
- readl(mmio + PDC_TBG_MODE); /* flush */
+ readl(host_mmio + PDC_TBG_MODE); /* flush */
msleep(10);
/* adjust slew rate control register. */
- tmp = readl(mmio + PDC_SLEW_CTL);
+ tmp = readl(host_mmio + PDC_SLEW_CTL);
tmp &= 0xFFFFF03F; /* clear bit 11 ~ 6 */
tmp |= 0x00000900; /* set bit 11-9 = 100b , bit 8-6 = 100 */
- writel(tmp, mmio + PDC_SLEW_CTL);
+ writel(tmp, host_mmio + PDC_SLEW_CTL);
}
static int pdc_ata_init_one(struct pci_dev *pdev,
@@ -1045,7 +1041,7 @@ static int pdc_ata_init_one(struct pci_dev *pdev,
const struct ata_port_info *pi = &pdc_port_info[ent->driver_data];
const struct ata_port_info *ppi[PDC_MAX_PORTS];
struct ata_host *host;
- void __iomem *base;
+ void __iomem *host_mmio;
int n_ports, i, rc;
int is_sataii_tx4;
@@ -1062,7 +1058,7 @@ static int pdc_ata_init_one(struct pci_dev *pdev,
pcim_pin_device(pdev);
if (rc)
return rc;
- base = pcim_iomap_table(pdev)[PDC_MMIO_BAR];
+ host_mmio = pcim_iomap_table(pdev)[PDC_MMIO_BAR];
/* determine port configuration and setup host */
n_ports = 2;
@@ -1072,7 +1068,7 @@ static int pdc_ata_init_one(struct pci_dev *pdev,
ppi[i] = pi;
if (pi->flags & PDC_FLAG_SATA_PATA) {
- u8 tmp = readb(base + PDC_FLASH_CTL+1);
+ u8 tmp = readb(host_mmio + PDC_FLASH_CTL + 1);
if (!(tmp & 0x80))
ppi[n_ports++] = pi + 1;
}
@@ -1088,13 +1084,13 @@ static int pdc_ata_init_one(struct pci_dev *pdev,
for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap = host->ports[i];
unsigned int ata_no = pdc_port_no_to_ata_no(i, is_sataii_tx4);
- unsigned int port_offset = 0x200 + ata_no * 0x80;
+ unsigned int ata_offset = 0x200 + ata_no * 0x80;
unsigned int scr_offset = 0x400 + ata_no * 0x100;
- pdc_ata_setup_port(ap, base + port_offset, base + scr_offset);
+ pdc_ata_setup_port(ap, host_mmio + ata_offset, host_mmio + scr_offset);
ata_port_pbar_desc(ap, PDC_MMIO_BAR, -1, "mmio");
- ata_port_pbar_desc(ap, PDC_MMIO_BAR, port_offset, "port");
+ ata_port_pbar_desc(ap, PDC_MMIO_BAR, ata_offset, "ata");
}
/* initialize adapter */
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index 27a1101..8ee6b5b 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -899,14 +899,25 @@ static bool sil24_qc_fill_rtf(struct ata_queued_cmd *qc)
static void sil24_pmp_attach(struct ata_port *ap)
{
+ u32 *gscr = ap->link.device->gscr;
+
sil24_config_pmp(ap, 1);
sil24_init_port(ap);
+
+ if (sata_pmp_gscr_vendor(gscr) == 0x11ab &&
+ sata_pmp_gscr_devid(gscr) == 0x4140) {
+ ata_port_printk(ap, KERN_INFO,
+ "disabling NCQ support due to sil24-mv4140 quirk\n");
+ ap->flags &= ~ATA_FLAG_NCQ;
+ }
}
static void sil24_pmp_detach(struct ata_port *ap)
{
sil24_init_port(ap);
sil24_config_pmp(ap, 0);
+
+ ap->flags |= ATA_FLAG_NCQ;
}
static int sil24_pmp_hardreset(struct ata_link *link, unsigned int *class,
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 0f17643..4a92fba 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -341,7 +341,7 @@ enum {
ATA_EH_PMP_TRIES = 5,
ATA_EH_PMP_LINK_TRIES = 3,
- SATA_PMP_SCR_TIMEOUT = 250,
+ SATA_PMP_RW_TIMEOUT = 3000, /* PMP read/write timeout */
/* Horkage types. May be set by libata or controller on drives
(some horkage may be drive/controller pair dependant */
@@ -351,7 +351,7 @@ enum {
ATA_HORKAGE_NONCQ = (1 << 2), /* Don't use NCQ */
ATA_HORKAGE_MAX_SEC_128 = (1 << 3), /* Limit max sects to 128 */
ATA_HORKAGE_BROKEN_HPA = (1 << 4), /* Broken HPA */
- ATA_HORKAGE_SKIP_PM = (1 << 5), /* Skip PM operations */
+ ATA_HORKAGE_DISABLE = (1 << 5), /* Disable it */
ATA_HORKAGE_HPA_SIZE = (1 << 6), /* native size off by one */
ATA_HORKAGE_IPM = (1 << 7), /* Link PM problems */
ATA_HORKAGE_IVB = (1 << 8), /* cbl det validity bit bugs */
@@ -821,8 +821,6 @@ struct ata_timing {
unsigned short udma; /* t2CYCTYP/2 */
};
-#define FIT(v, vmin, vmax) max_t(short, min_t(short, v, vmax), vmin)
-
/*
* Core layer - drivers/ata/libata-core.c
*/
^ permalink raw reply related [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2008-05-06 15:48 Jeff Garzik
@ 2008-05-06 16:23 ` Linus Torvalds
0 siblings, 0 replies; 95+ messages in thread
From: Linus Torvalds @ 2008-05-06 16:23 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Andrew Morton, linux-ide, LKML
On Tue, 6 May 2008, Jeff Garzik wrote:
>
> +config PATA_SCH
> + tristate "Intel SCH PATA support"
> + depends on PCI
> + help
> + This option enables support for Intel SCH PATA on the Intel
> + SCH (US15W, US15L, UL11L) series host controllers.
> +
> + If unsure, say N.
I think it would generally be good if people explained their drivers
better than this.
If you know what the hell an SCH is, you don't *need* that help message in
the first place! Agreed?
IOW, when adding drivers, please add help messages that actually explain
what the driver is from a *user* perspective, not from a chip designer
perspective. In this case, something like
The Intel SCH chipset is the new low-power, small-footprint
embedded chipset that is generally paired with the Atom CPU and is
not their normal PC chipset.
or something. So that people can actually make a somewhat informed guess
about whether it's relevant to them or not.
Linus
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2008-05-06 15:48 Jeff Garzik
2008-05-06 16:23 ` Linus Torvalds
0 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2008-05-06 15:48 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
- sata_mv: continued fixing
- sata_inic: make it actually work
- new driver from Intel
- misc fixes from Tejun
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/Kconfig | 13 +-
drivers/ata/Makefile | 1 +
drivers/ata/ahci.c | 4 +-
drivers/ata/ata_generic.c | 6 +
drivers/ata/ata_piix.c | 25 ++
drivers/ata/libata-core.c | 1 +
drivers/ata/libata-eh.c | 2 +-
drivers/ata/libata-sff.c | 6 +-
drivers/ata/pata_acpi.c | 6 +
drivers/ata/pata_sch.c | 206 +++++++++++++
drivers/ata/sata_inic162x.c | 646 ++++++++++++++++++++++++++--------------
drivers/ata/sata_mv.c | 688 +++++++++++++++++++++++++++++++++----------
include/linux/libata.h | 16 +
13 files changed, 1222 insertions(+), 398 deletions(-)
create mode 100644 drivers/ata/pata_sch.c
Alan Cox (1):
pata_atiixp: Don't disable
Alek Du (1):
libata: Add Intel SCH PATA driver
Mark Lord (13):
sata_mv more cosmetic changes
sata_mv pci features
sata_mv wait for empty+idle
sata_mv new mv_qc_defer method
sata_mv errata workaround for sata25 part 1
sata_mv rearrange mv_config_fbs
sata_mv NCQ and SError fixes for mv_err_intr
sata_mv fix mv_host_intr bug for hc_irq_cause
sata_mv new mv_port_intr function
libata: export ata_eh_analyze_ncq_error
sata_mv delayed eh handling
sata_mv NCQ-EH for FIS-based switching
sata_mv use hweight16() for bit counting (V2)
Tejun Heo (12):
libata: improve post-reset device ready test
ata_piix: verify SIDPR access before enabling it
sata_inic162x: misc clean ups
sata_inic162x: add / update constants
sata_inic162x: update TF read handling
sata_inic162x: use IDMA for ATA_PROT_DMA
sata_inic162x: kill now unused bmdma related stuff
sata_inic162x: use IDMA for non DMA ATA commands
sata_inic162x: use IDMA for ATAPI commands
sata_inic162x: kill now unused SFF related stuff
sata_inic162x: add cardbus support
sata_inic162x: update intro comment, up the version and drop EXPERIMENTAL
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 1c11df9..9bf2986 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -205,8 +205,8 @@ config SATA_VITESSE
If unsure, say N.
config SATA_INIC162X
- tristate "Initio 162x SATA support (HIGHLY EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ tristate "Initio 162x SATA support"
+ depends on PCI
help
This option enables support for Initio 162x Serial ATA.
@@ -697,6 +697,15 @@ config PATA_SCC
If unsure, say N.
+config PATA_SCH
+ tristate "Intel SCH PATA support"
+ depends on PCI
+ help
+ This option enables support for Intel SCH PATA on the Intel
+ SCH (US15W, US15L, UL11L) series host controllers.
+
+ If unsure, say N.
+
config PATA_BF54X
tristate "Blackfin 54x ATAPI support"
depends on BF542 || BF548 || BF549
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index b693d82..674965f 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -67,6 +67,7 @@ obj-$(CONFIG_PATA_SIS) += pata_sis.o
obj-$(CONFIG_PATA_TRIFLEX) += pata_triflex.o
obj-$(CONFIG_PATA_IXP4XX_CF) += pata_ixp4xx_cf.o
obj-$(CONFIG_PATA_SCC) += pata_scc.o
+obj-$(CONFIG_PATA_SCH) += pata_sch.o
obj-$(CONFIG_PATA_BF54X) += pata_bf54x.o
obj-$(CONFIG_PATA_PLATFORM) += pata_platform.o
obj-$(CONFIG_PATA_OF_PLATFORM) += pata_of_platform.o
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 8cace9a..97f83fb 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -1267,9 +1267,7 @@ static int ahci_check_ready(struct ata_link *link)
void __iomem *port_mmio = ahci_port_base(link->ap);
u8 status = readl(port_mmio + PORT_TFDATA) & 0xFF;
- if (!(status & ATA_BUSY))
- return 1;
- return 0;
+ return ata_check_ready(status);
}
static int ahci_softreset(struct ata_link *link, unsigned int *class,
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
index 47aeccd..75a406f 100644
--- a/drivers/ata/ata_generic.c
+++ b/drivers/ata/ata_generic.c
@@ -152,6 +152,12 @@ static int ata_generic_init_one(struct pci_dev *dev, const struct pci_device_id
if (dev->vendor == PCI_VENDOR_ID_AL)
ata_pci_bmdma_clear_simplex(dev);
+ if (dev->vendor == PCI_VENDOR_ID_ATI) {
+ int rc = pcim_enable_device(dev);
+ if (rc < 0)
+ return rc;
+ pcim_pin_device(dev);
+ }
return ata_pci_sff_init_one(dev, ppi, &generic_sht, NULL);
}
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index ea2c764..a9027b8 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -1348,6 +1348,8 @@ static void __devinit piix_init_sidpr(struct ata_host *host)
{
struct pci_dev *pdev = to_pci_dev(host->dev);
struct piix_host_priv *hpriv = host->private_data;
+ struct ata_device *dev0 = &host->ports[0]->link.device[0];
+ u32 scontrol;
int i;
/* check for availability */
@@ -1366,6 +1368,29 @@ static void __devinit piix_init_sidpr(struct ata_host *host)
return;
hpriv->sidpr = pcim_iomap_table(pdev)[PIIX_SIDPR_BAR];
+
+ /* SCR access via SIDPR doesn't work on some configurations.
+ * Give it a test drive by inhibiting power save modes which
+ * we'll do anyway.
+ */
+ scontrol = piix_sidpr_read(dev0, SCR_CONTROL);
+
+ /* if IPM is already 3, SCR access is probably working. Don't
+ * un-inhibit power save modes as BIOS might have inhibited
+ * them for a reason.
+ */
+ if ((scontrol & 0xf00) != 0x300) {
+ scontrol |= 0x300;
+ piix_sidpr_write(dev0, SCR_CONTROL, scontrol);
+ scontrol = piix_sidpr_read(dev0, SCR_CONTROL);
+
+ if ((scontrol & 0xf00) != 0x300) {
+ dev_printk(KERN_INFO, host->dev, "SCR access via "
+ "SIDPR is available but doesn't work\n");
+ return;
+ }
+ }
+
host->ports[0]->ops = &piix_sidpr_sata_ops;
host->ports[1]->ops = &piix_sidpr_sata_ops;
}
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 3bc4885..927b692 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -6292,6 +6292,7 @@ EXPORT_SYMBOL_GPL(ata_eh_freeze_port);
EXPORT_SYMBOL_GPL(ata_eh_thaw_port);
EXPORT_SYMBOL_GPL(ata_eh_qc_complete);
EXPORT_SYMBOL_GPL(ata_eh_qc_retry);
+EXPORT_SYMBOL_GPL(ata_eh_analyze_ncq_error);
EXPORT_SYMBOL_GPL(ata_do_eh);
EXPORT_SYMBOL_GPL(ata_std_error_handler);
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 61dcd00..62e0331 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -1357,7 +1357,7 @@ static void ata_eh_analyze_serror(struct ata_link *link)
* LOCKING:
* Kernel thread context (may sleep).
*/
-static void ata_eh_analyze_ncq_error(struct ata_link *link)
+void ata_eh_analyze_ncq_error(struct ata_link *link)
{
struct ata_port *ap = link->ap;
struct ata_eh_context *ehc = &link->eh_context;
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index 2ec65a8..3c2d228 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -314,11 +314,7 @@ static int ata_sff_check_ready(struct ata_link *link)
{
u8 status = link->ap->ops->sff_check_status(link->ap);
- if (!(status & ATA_BUSY))
- return 1;
- if (status == 0xff)
- return -ENODEV;
- return 0;
+ return ata_check_ready(status);
}
/**
diff --git a/drivers/ata/pata_acpi.c b/drivers/ata/pata_acpi.c
index c5f91e6..fbe6057 100644
--- a/drivers/ata/pata_acpi.c
+++ b/drivers/ata/pata_acpi.c
@@ -259,6 +259,12 @@ static int pacpi_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &pacpi_ops,
};
const struct ata_port_info *ppi[] = { &info, NULL };
+ if (pdev->vendor == PCI_VENDOR_ID_ATI) {
+ int rc = pcim_enable_device(pdev);
+ if (rc < 0)
+ return rc;
+ pcim_pin_device(pdev);
+ }
return ata_pci_sff_init_one(pdev, ppi, &pacpi_sht, NULL);
}
diff --git a/drivers/ata/pata_sch.c b/drivers/ata/pata_sch.c
new file mode 100644
index 0000000..c8cc027
--- /dev/null
+++ b/drivers/ata/pata_sch.c
@@ -0,0 +1,206 @@
+/*
+ * pata_sch.c - Intel SCH PATA controllers
+ *
+ * Copyright (c) 2008 Alek Du <alek.du@intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License 2 as published
+ * by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING. If not, write to
+ * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+/*
+ * Supports:
+ * Intel SCH (AF82US15W, AF82US15L, AF82UL11L) chipsets -- see spec at:
+ * http://download.intel.com/design/chipsets/embedded/datashts/319537.pdf
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/dmi.h>
+
+#define DRV_NAME "pata_sch"
+#define DRV_VERSION "0.2"
+
+/* see SCH datasheet page 351 */
+enum {
+ D0TIM = 0x80, /* Device 0 Timing Register */
+ D1TIM = 0x84, /* Device 1 Timing Register */
+ PM = 0x07, /* PIO Mode Bit Mask */
+ MDM = (0x03 << 8), /* Multi-word DMA Mode Bit Mask */
+ UDM = (0x07 << 16), /* Ultra DMA Mode Bit Mask */
+ PPE = (1 << 30), /* Prefetch/Post Enable */
+ USD = (1 << 31), /* Use Synchronous DMA */
+};
+
+static int sch_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent);
+static void sch_set_piomode(struct ata_port *ap, struct ata_device *adev);
+static void sch_set_dmamode(struct ata_port *ap, struct ata_device *adev);
+
+static const struct pci_device_id sch_pci_tbl[] = {
+ /* Intel SCH PATA Controller */
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_SCH_IDE), 0 },
+ { } /* terminate list */
+};
+
+static struct pci_driver sch_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = sch_pci_tbl,
+ .probe = sch_init_one,
+ .remove = ata_pci_remove_one,
+#ifdef CONFIG_PM
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
+#endif
+};
+
+static struct scsi_host_template sch_sht = {
+ ATA_BMDMA_SHT(DRV_NAME),
+};
+
+static struct ata_port_operations sch_pata_ops = {
+ .inherits = &ata_bmdma_port_ops,
+ .cable_detect = ata_cable_unknown,
+ .set_piomode = sch_set_piomode,
+ .set_dmamode = sch_set_dmamode,
+};
+
+static struct ata_port_info sch_port_info = {
+ .flags = 0,
+ .pio_mask = ATA_PIO4, /* pio0-4 */
+ .mwdma_mask = ATA_MWDMA2, /* mwdma0-2 */
+ .udma_mask = ATA_UDMA5, /* udma0-5 */
+ .port_ops = &sch_pata_ops,
+};
+
+MODULE_AUTHOR("Alek Du <alek.du@intel.com>");
+MODULE_DESCRIPTION("SCSI low-level driver for Intel SCH PATA controllers");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, sch_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
+/**
+ * sch_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: ATA device
+ *
+ * Set PIO mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void sch_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int pio = adev->pio_mode - XFER_PIO_0;
+ struct pci_dev *dev = to_pci_dev(ap->host->dev);
+ unsigned int port = adev->devno ? D1TIM : D0TIM;
+ unsigned int data;
+
+ pci_read_config_dword(dev, port, &data);
+ /* see SCH datasheet page 351 */
+ /* set PIO mode */
+ data &= ~(PM | PPE);
+ data |= pio;
+ /* enable PPE for block device */
+ if (adev->class == ATA_DEV_ATA)
+ data |= PPE;
+ pci_write_config_dword(dev, port, data);
+}
+
+/**
+ * sch_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: ATA device
+ *
+ * Set MW/UDMA mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void sch_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int dma_mode = adev->dma_mode;
+ struct pci_dev *dev = to_pci_dev(ap->host->dev);
+ unsigned int port = adev->devno ? D1TIM : D0TIM;
+ unsigned int data;
+
+ pci_read_config_dword(dev, port, &data);
+ /* see SCH datasheet page 351 */
+ if (dma_mode >= XFER_UDMA_0) {
+ /* enable Synchronous DMA mode */
+ data |= USD;
+ data &= ~UDM;
+ data |= (dma_mode - XFER_UDMA_0) << 16;
+ } else { /* must be MWDMA mode, since we masked SWDMA already */
+ data &= ~(USD | MDM);
+ data |= (dma_mode - XFER_MW_DMA_0) << 8;
+ }
+ pci_write_config_dword(dev, port, data);
+}
+
+/**
+ * sch_init_one - Register SCH ATA PCI device with kernel services
+ * @pdev: PCI device to register
+ * @ent: Entry in sch_pci_tbl matching with @pdev
+ *
+ * LOCKING:
+ * Inherited from PCI layer (may sleep).
+ *
+ * RETURNS:
+ * Zero on success, or -ERRNO value.
+ */
+
+static int __devinit sch_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ static int printed_version;
+ const struct ata_port_info *ppi[] = { &sch_port_info, NULL };
+ struct ata_host *host;
+ int rc;
+
+ if (!printed_version++)
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "version " DRV_VERSION "\n");
+
+ /* enable device and prepare host */
+ rc = pcim_enable_device(pdev);
+ if (rc)
+ return rc;
+ rc = ata_pci_sff_prepare_host(pdev, ppi, &host);
+ if (rc)
+ return rc;
+ pci_set_master(pdev);
+ return ata_pci_sff_activate_host(host, ata_sff_interrupt, &sch_sht);
+}
+
+static int __init sch_init(void)
+{
+ return pci_register_driver(&sch_pci_driver);
+}
+
+static void __exit sch_exit(void)
+{
+ pci_unregister_driver(&sch_pci_driver);
+}
+
+module_init(sch_init);
+module_exit(sch_exit);
diff --git a/drivers/ata/sata_inic162x.c b/drivers/ata/sata_inic162x.c
index d27bb9a..3ead02f 100644
--- a/drivers/ata/sata_inic162x.c
+++ b/drivers/ata/sata_inic162x.c
@@ -10,13 +10,33 @@
* right. Documentation is available at initio's website but it only
* documents registers (not programming model).
*
- * - ATA disks work.
- * - Hotplug works.
- * - ATAPI read works but burning doesn't. This thing is really
- * peculiar about ATAPI and I couldn't figure out how ATAPI PIO and
- * ATAPI DMA WRITE should be programmed. If you've got a clue, be
- * my guest.
- * - Both STR and STD work.
+ * This driver has interesting history. The first version was written
+ * from the documentation and a 2.4 IDE driver posted on a Taiwan
+ * company, which didn't use any IDMA features and couldn't handle
+ * LBA48. The resulting driver couldn't handle LBA48 devices either
+ * making it pretty useless.
+ *
+ * After a while, initio picked the driver up, renamed it to
+ * sata_initio162x, updated it to use IDMA for ATA DMA commands and
+ * posted it on their website. It only used ATA_PROT_DMA for IDMA and
+ * attaching both devices and issuing IDMA and !IDMA commands
+ * simultaneously broke it due to PIRQ masking interaction but it did
+ * show how to use the IDMA (ADMA + some initio specific twists)
+ * engine.
+ *
+ * Then, I picked up their changes again and here's the usable driver
+ * which uses IDMA for everything. Everything works now including
+ * LBA48, CD/DVD burning, suspend/resume and hotplug. There are some
+ * issues tho. Result Tf is not resported properly, NCQ isn't
+ * supported yet and CD/DVD writing works with DMA assisted PIO
+ * protocol (which, for native SATA devices, shouldn't cause any
+ * noticeable difference).
+ *
+ * Anyways, so, here's finally a working driver for inic162x. Enjoy!
+ *
+ * initio: If you guys wanna improve the driver regarding result TF
+ * access and other stuff, please feel free to contact me. I'll be
+ * happy to assist.
*/
#include <linux/kernel.h>
@@ -28,13 +48,19 @@
#include <scsi/scsi_device.h>
#define DRV_NAME "sata_inic162x"
-#define DRV_VERSION "0.3"
+#define DRV_VERSION "0.4"
enum {
- MMIO_BAR = 5,
+ MMIO_BAR_PCI = 5,
+ MMIO_BAR_CARDBUS = 1,
NR_PORTS = 2,
+ IDMA_CPB_TBL_SIZE = 4 * 32,
+
+ INIC_DMA_BOUNDARY = 0xffffff,
+
+ HOST_ACTRL = 0x08,
HOST_CTL = 0x7c,
HOST_STAT = 0x7e,
HOST_IRQ_STAT = 0xbc,
@@ -43,22 +69,37 @@ enum {
PORT_SIZE = 0x40,
/* registers for ATA TF operation */
- PORT_TF = 0x00,
- PORT_ALT_STAT = 0x08,
+ PORT_TF_DATA = 0x00,
+ PORT_TF_FEATURE = 0x01,
+ PORT_TF_NSECT = 0x02,
+ PORT_TF_LBAL = 0x03,
+ PORT_TF_LBAM = 0x04,
+ PORT_TF_LBAH = 0x05,
+ PORT_TF_DEVICE = 0x06,
+ PORT_TF_COMMAND = 0x07,
+ PORT_TF_ALT_STAT = 0x08,
PORT_IRQ_STAT = 0x09,
PORT_IRQ_MASK = 0x0a,
PORT_PRD_CTL = 0x0b,
PORT_PRD_ADDR = 0x0c,
PORT_PRD_XFERLEN = 0x10,
+ PORT_CPB_CPBLAR = 0x18,
+ PORT_CPB_PTQFIFO = 0x1c,
/* IDMA register */
PORT_IDMA_CTL = 0x14,
+ PORT_IDMA_STAT = 0x16,
+
+ PORT_RPQ_FIFO = 0x1e,
+ PORT_RPQ_CNT = 0x1f,
PORT_SCR = 0x20,
/* HOST_CTL bits */
HCTL_IRQOFF = (1 << 8), /* global IRQ off */
- HCTL_PWRDWN = (1 << 13), /* power down PHYs */
+ HCTL_FTHD0 = (1 << 10), /* fifo threshold 0 */
+ HCTL_FTHD1 = (1 << 11), /* fifo threshold 1*/
+ HCTL_PWRDWN = (1 << 12), /* power down PHYs */
HCTL_SOFTRST = (1 << 13), /* global reset (no phy reset) */
HCTL_RPGSEL = (1 << 15), /* register page select */
@@ -81,9 +122,7 @@ enum {
PIRQ_PENDING = (1 << 7), /* port IRQ pending (STAT only) */
PIRQ_ERR = PIRQ_OFFLINE | PIRQ_ONLINE | PIRQ_FATAL,
-
- PIRQ_MASK_DMA_READ = PIRQ_REPLY | PIRQ_ATA,
- PIRQ_MASK_OTHER = PIRQ_REPLY | PIRQ_COMPLETE,
+ PIRQ_MASK_DEFAULT = PIRQ_REPLY | PIRQ_ATA,
PIRQ_MASK_FREEZE = 0xff,
/* PORT_PRD_CTL bits */
@@ -96,20 +135,104 @@ enum {
IDMA_CTL_RST_IDMA = (1 << 5), /* reset IDMA machinary */
IDMA_CTL_GO = (1 << 7), /* IDMA mode go */
IDMA_CTL_ATA_NIEN = (1 << 8), /* ATA IRQ disable */
+
+ /* PORT_IDMA_STAT bits */
+ IDMA_STAT_PERR = (1 << 0), /* PCI ERROR MODE */
+ IDMA_STAT_CPBERR = (1 << 1), /* ADMA CPB error */
+ IDMA_STAT_LGCY = (1 << 3), /* ADMA legacy */
+ IDMA_STAT_UIRQ = (1 << 4), /* ADMA unsolicited irq */
+ IDMA_STAT_STPD = (1 << 5), /* ADMA stopped */
+ IDMA_STAT_PSD = (1 << 6), /* ADMA pause */
+ IDMA_STAT_DONE = (1 << 7), /* ADMA done */
+
+ IDMA_STAT_ERR = IDMA_STAT_PERR | IDMA_STAT_CPBERR,
+
+ /* CPB Control Flags*/
+ CPB_CTL_VALID = (1 << 0), /* CPB valid */
+ CPB_CTL_QUEUED = (1 << 1), /* queued command */
+ CPB_CTL_DATA = (1 << 2), /* data, rsvd in datasheet */
+ CPB_CTL_IEN = (1 << 3), /* PCI interrupt enable */
+ CPB_CTL_DEVDIR = (1 << 4), /* device direction control */
+
+ /* CPB Response Flags */
+ CPB_RESP_DONE = (1 << 0), /* ATA command complete */
+ CPB_RESP_REL = (1 << 1), /* ATA release */
+ CPB_RESP_IGNORED = (1 << 2), /* CPB ignored */
+ CPB_RESP_ATA_ERR = (1 << 3), /* ATA command error */
+ CPB_RESP_SPURIOUS = (1 << 4), /* ATA spurious interrupt error */
+ CPB_RESP_UNDERFLOW = (1 << 5), /* APRD deficiency length error */
+ CPB_RESP_OVERFLOW = (1 << 6), /* APRD exccess length error */
+ CPB_RESP_CPB_ERR = (1 << 7), /* CPB error flag */
+
+ /* PRD Control Flags */
+ PRD_DRAIN = (1 << 1), /* ignore data excess */
+ PRD_CDB = (1 << 2), /* atapi packet command pointer */
+ PRD_DIRECT_INTR = (1 << 3), /* direct interrupt */
+ PRD_DMA = (1 << 4), /* data transfer method */
+ PRD_WRITE = (1 << 5), /* data dir, rsvd in datasheet */
+ PRD_IOM = (1 << 6), /* io/memory transfer */
+ PRD_END = (1 << 7), /* APRD chain end */
};
+/* Comman Parameter Block */
+struct inic_cpb {
+ u8 resp_flags; /* Response Flags */
+ u8 error; /* ATA Error */
+ u8 status; /* ATA Status */
+ u8 ctl_flags; /* Control Flags */
+ __le32 len; /* Total Transfer Length */
+ __le32 prd; /* First PRD pointer */
+ u8 rsvd[4];
+ /* 16 bytes */
+ u8 feature; /* ATA Feature */
+ u8 hob_feature; /* ATA Ex. Feature */
+ u8 device; /* ATA Device/Head */
+ u8 mirctl; /* Mirror Control */
+ u8 nsect; /* ATA Sector Count */
+ u8 hob_nsect; /* ATA Ex. Sector Count */
+ u8 lbal; /* ATA Sector Number */
+ u8 hob_lbal; /* ATA Ex. Sector Number */
+ u8 lbam; /* ATA Cylinder Low */
+ u8 hob_lbam; /* ATA Ex. Cylinder Low */
+ u8 lbah; /* ATA Cylinder High */
+ u8 hob_lbah; /* ATA Ex. Cylinder High */
+ u8 command; /* ATA Command */
+ u8 ctl; /* ATA Control */
+ u8 slave_error; /* Slave ATA Error */
+ u8 slave_status; /* Slave ATA Status */
+ /* 32 bytes */
+} __packed;
+
+/* Physical Region Descriptor */
+struct inic_prd {
+ __le32 mad; /* Physical Memory Address */
+ __le16 len; /* Transfer Length */
+ u8 rsvd;
+ u8 flags; /* Control Flags */
+} __packed;
+
+struct inic_pkt {
+ struct inic_cpb cpb;
+ struct inic_prd prd[LIBATA_MAX_PRD + 1]; /* + 1 for cdb */
+ u8 cdb[ATAPI_CDB_LEN];
+} __packed;
+
struct inic_host_priv {
- u16 cached_hctl;
+ void __iomem *mmio_base;
+ u16 cached_hctl;
};
struct inic_port_priv {
- u8 dfl_prdctl;
- u8 cached_prdctl;
- u8 cached_pirq_mask;
+ struct inic_pkt *pkt;
+ dma_addr_t pkt_dma;
+ u32 *cpb_tbl;
+ dma_addr_t cpb_tbl_dma;
};
static struct scsi_host_template inic_sht = {
- ATA_BMDMA_SHT(DRV_NAME),
+ ATA_BASE_SHT(DRV_NAME),
+ .sg_tablesize = LIBATA_MAX_PRD, /* maybe it can be larger? */
+ .dma_boundary = INIC_DMA_BOUNDARY,
};
static const int scr_map[] = {
@@ -120,54 +243,34 @@ static const int scr_map[] = {
static void __iomem *inic_port_base(struct ata_port *ap)
{
- return ap->host->iomap[MMIO_BAR] + ap->port_no * PORT_SIZE;
-}
-
-static void __inic_set_pirq_mask(struct ata_port *ap, u8 mask)
-{
- void __iomem *port_base = inic_port_base(ap);
- struct inic_port_priv *pp = ap->private_data;
+ struct inic_host_priv *hpriv = ap->host->private_data;
- writeb(mask, port_base + PORT_IRQ_MASK);
- pp->cached_pirq_mask = mask;
-}
-
-static void inic_set_pirq_mask(struct ata_port *ap, u8 mask)
-{
- struct inic_port_priv *pp = ap->private_data;
-
- if (pp->cached_pirq_mask != mask)
- __inic_set_pirq_mask(ap, mask);
+ return hpriv->mmio_base + ap->port_no * PORT_SIZE;
}
static void inic_reset_port(void __iomem *port_base)
{
void __iomem *idma_ctl = port_base + PORT_IDMA_CTL;
- u16 ctl;
- ctl = readw(idma_ctl);
- ctl &= ~(IDMA_CTL_RST_IDMA | IDMA_CTL_ATA_NIEN | IDMA_CTL_GO);
+ /* stop IDMA engine */
+ readw(idma_ctl); /* flush */
+ msleep(1);
/* mask IRQ and assert reset */
- writew(ctl | IDMA_CTL_RST_IDMA | IDMA_CTL_ATA_NIEN, idma_ctl);
+ writew(IDMA_CTL_RST_IDMA, idma_ctl);
readw(idma_ctl); /* flush */
-
- /* give it some time */
msleep(1);
/* release reset */
- writew(ctl | IDMA_CTL_ATA_NIEN, idma_ctl);
+ writew(0, idma_ctl);
/* clear irq */
writeb(0xff, port_base + PORT_IRQ_STAT);
-
- /* reenable ATA IRQ, turn off IDMA mode */
- writew(ctl, idma_ctl);
}
static int inic_scr_read(struct ata_port *ap, unsigned sc_reg, u32 *val)
{
- void __iomem *scr_addr = ap->ioaddr.scr_addr;
+ void __iomem *scr_addr = inic_port_base(ap) + PORT_SCR;
void __iomem *addr;
if (unlikely(sc_reg >= ARRAY_SIZE(scr_map)))
@@ -184,120 +287,126 @@ static int inic_scr_read(struct ata_port *ap, unsigned sc_reg, u32 *val)
static int inic_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val)
{
- void __iomem *scr_addr = ap->ioaddr.scr_addr;
- void __iomem *addr;
+ void __iomem *scr_addr = inic_port_base(ap) + PORT_SCR;
if (unlikely(sc_reg >= ARRAY_SIZE(scr_map)))
return -EINVAL;
- addr = scr_addr + scr_map[sc_reg] * 4;
writel(val, scr_addr + scr_map[sc_reg] * 4);
return 0;
}
-/*
- * In TF mode, inic162x is very similar to SFF device. TF registers
- * function the same. DMA engine behaves similary using the same PRD
- * format as BMDMA but different command register, interrupt and event
- * notification methods are used. The following inic_bmdma_*()
- * functions do the impedance matching.
- */
-static void inic_bmdma_setup(struct ata_queued_cmd *qc)
+static void inic_stop_idma(struct ata_port *ap)
{
- struct ata_port *ap = qc->ap;
- struct inic_port_priv *pp = ap->private_data;
void __iomem *port_base = inic_port_base(ap);
- int rw = qc->tf.flags & ATA_TFLAG_WRITE;
-
- /* make sure device sees PRD table writes */
- wmb();
-
- /* load transfer length */
- writel(qc->nbytes, port_base + PORT_PRD_XFERLEN);
-
- /* turn on DMA and specify data direction */
- pp->cached_prdctl = pp->dfl_prdctl | PRD_CTL_DMAEN;
- if (!rw)
- pp->cached_prdctl |= PRD_CTL_WR;
- writeb(pp->cached_prdctl, port_base + PORT_PRD_CTL);
- /* issue r/w command */
- ap->ops->sff_exec_command(ap, &qc->tf);
+ readb(port_base + PORT_RPQ_FIFO);
+ readb(port_base + PORT_RPQ_CNT);
+ writew(0, port_base + PORT_IDMA_CTL);
}
-static void inic_bmdma_start(struct ata_queued_cmd *qc)
+static void inic_host_err_intr(struct ata_port *ap, u8 irq_stat, u16 idma_stat)
{
- struct ata_port *ap = qc->ap;
+ struct ata_eh_info *ehi = &ap->link.eh_info;
struct inic_port_priv *pp = ap->private_data;
- void __iomem *port_base = inic_port_base(ap);
+ struct inic_cpb *cpb = &pp->pkt->cpb;
+ bool freeze = false;
- /* start host DMA transaction */
- pp->cached_prdctl |= PRD_CTL_START;
- writeb(pp->cached_prdctl, port_base + PORT_PRD_CTL);
-}
+ ata_ehi_clear_desc(ehi);
+ ata_ehi_push_desc(ehi, "irq_stat=0x%x idma_stat=0x%x",
+ irq_stat, idma_stat);
-static void inic_bmdma_stop(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- struct inic_port_priv *pp = ap->private_data;
- void __iomem *port_base = inic_port_base(ap);
+ inic_stop_idma(ap);
- /* stop DMA engine */
- writeb(pp->dfl_prdctl, port_base + PORT_PRD_CTL);
-}
+ if (irq_stat & (PIRQ_OFFLINE | PIRQ_ONLINE)) {
+ ata_ehi_push_desc(ehi, "hotplug");
+ ata_ehi_hotplugged(ehi);
+ freeze = true;
+ }
-static u8 inic_bmdma_status(struct ata_port *ap)
-{
- /* event is already verified by the interrupt handler */
- return ATA_DMA_INTR;
+ if (idma_stat & IDMA_STAT_PERR) {
+ ata_ehi_push_desc(ehi, "PCI error");
+ freeze = true;
+ }
+
+ if (idma_stat & IDMA_STAT_CPBERR) {
+ ata_ehi_push_desc(ehi, "CPB error");
+
+ if (cpb->resp_flags & CPB_RESP_IGNORED) {
+ __ata_ehi_push_desc(ehi, " ignored");
+ ehi->err_mask |= AC_ERR_INVALID;
+ freeze = true;
+ }
+
+ if (cpb->resp_flags & CPB_RESP_ATA_ERR)
+ ehi->err_mask |= AC_ERR_DEV;
+
+ if (cpb->resp_flags & CPB_RESP_SPURIOUS) {
+ __ata_ehi_push_desc(ehi, " spurious-intr");
+ ehi->err_mask |= AC_ERR_HSM;
+ freeze = true;
+ }
+
+ if (cpb->resp_flags &
+ (CPB_RESP_UNDERFLOW | CPB_RESP_OVERFLOW)) {
+ __ata_ehi_push_desc(ehi, " data-over/underflow");
+ ehi->err_mask |= AC_ERR_HSM;
+ freeze = true;
+ }
+ }
+
+ if (freeze)
+ ata_port_freeze(ap);
+ else
+ ata_port_abort(ap);
}
static void inic_host_intr(struct ata_port *ap)
{
void __iomem *port_base = inic_port_base(ap);
- struct ata_eh_info *ehi = &ap->link.eh_info;
+ struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->link.active_tag);
u8 irq_stat;
+ u16 idma_stat;
- /* fetch and clear irq */
+ /* read and clear IRQ status */
irq_stat = readb(port_base + PORT_IRQ_STAT);
writeb(irq_stat, port_base + PORT_IRQ_STAT);
+ idma_stat = readw(port_base + PORT_IDMA_STAT);
- if (likely(!(irq_stat & PIRQ_ERR))) {
- struct ata_queued_cmd *qc =
- ata_qc_from_tag(ap, ap->link.active_tag);
+ if (unlikely((irq_stat & PIRQ_ERR) || (idma_stat & IDMA_STAT_ERR)))
+ inic_host_err_intr(ap, irq_stat, idma_stat);
- if (unlikely(!qc || (qc->tf.flags & ATA_TFLAG_POLLING))) {
- ap->ops->sff_check_status(ap); /* clear ATA interrupt */
- return;
- }
+ if (unlikely(!qc))
+ goto spurious;
- if (likely(ata_sff_host_intr(ap, qc)))
- return;
+ if (likely(idma_stat & IDMA_STAT_DONE)) {
+ inic_stop_idma(ap);
- ap->ops->sff_check_status(ap); /* clear ATA interrupt */
- ata_port_printk(ap, KERN_WARNING, "unhandled "
- "interrupt, irq_stat=%x\n", irq_stat);
+ /* Depending on circumstances, device error
+ * isn't reported by IDMA, check it explicitly.
+ */
+ if (unlikely(readb(port_base + PORT_TF_COMMAND) &
+ (ATA_DF | ATA_ERR)))
+ qc->err_mask |= AC_ERR_DEV;
+
+ ata_qc_complete(qc);
return;
}
- /* error */
- ata_ehi_push_desc(ehi, "irq_stat=0x%x", irq_stat);
-
- if (irq_stat & (PIRQ_OFFLINE | PIRQ_ONLINE)) {
- ata_ehi_hotplugged(ehi);
- ata_port_freeze(ap);
- } else
- ata_port_abort(ap);
+ spurious:
+ ata_port_printk(ap, KERN_WARNING, "unhandled interrupt: "
+ "cmd=0x%x irq_stat=0x%x idma_stat=0x%x\n",
+ qc ? qc->tf.command : 0xff, irq_stat, idma_stat);
}
static irqreturn_t inic_interrupt(int irq, void *dev_instance)
{
struct ata_host *host = dev_instance;
- void __iomem *mmio_base = host->iomap[MMIO_BAR];
+ struct inic_host_priv *hpriv = host->private_data;
u16 host_irq_stat;
int i, handled = 0;;
- host_irq_stat = readw(mmio_base + HOST_IRQ_STAT);
+ host_irq_stat = readw(hpriv->mmio_base + HOST_IRQ_STAT);
if (unlikely(!(host_irq_stat & HIRQ_GLOBAL)))
goto out;
@@ -327,60 +436,173 @@ static irqreturn_t inic_interrupt(int irq, void *dev_instance)
return IRQ_RETVAL(handled);
}
+static int inic_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+ /* For some reason ATAPI_PROT_DMA doesn't work for some
+ * commands including writes and other misc ops. Use PIO
+ * protocol instead, which BTW is driven by the DMA engine
+ * anyway, so it shouldn't make much difference for native
+ * SATA devices.
+ */
+ if (atapi_cmd_type(qc->cdb[0]) == READ)
+ return 0;
+ return 1;
+}
+
+static void inic_fill_sg(struct inic_prd *prd, struct ata_queued_cmd *qc)
+{
+ struct scatterlist *sg;
+ unsigned int si;
+ u8 flags = 0;
+
+ if (qc->tf.flags & ATA_TFLAG_WRITE)
+ flags |= PRD_WRITE;
+
+ if (ata_is_dma(qc->tf.protocol))
+ flags |= PRD_DMA;
+
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
+ prd->mad = cpu_to_le32(sg_dma_address(sg));
+ prd->len = cpu_to_le16(sg_dma_len(sg));
+ prd->flags = flags;
+ prd++;
+ }
+
+ WARN_ON(!si);
+ prd[-1].flags |= PRD_END;
+}
+
+static void inic_qc_prep(struct ata_queued_cmd *qc)
+{
+ struct inic_port_priv *pp = qc->ap->private_data;
+ struct inic_pkt *pkt = pp->pkt;
+ struct inic_cpb *cpb = &pkt->cpb;
+ struct inic_prd *prd = pkt->prd;
+ bool is_atapi = ata_is_atapi(qc->tf.protocol);
+ bool is_data = ata_is_data(qc->tf.protocol);
+ unsigned int cdb_len = 0;
+
+ VPRINTK("ENTER\n");
+
+ if (is_atapi)
+ cdb_len = qc->dev->cdb_len;
+
+ /* prepare packet, based on initio driver */
+ memset(pkt, 0, sizeof(struct inic_pkt));
+
+ cpb->ctl_flags = CPB_CTL_VALID | CPB_CTL_IEN;
+ if (is_atapi || is_data)
+ cpb->ctl_flags |= CPB_CTL_DATA;
+
+ cpb->len = cpu_to_le32(qc->nbytes + cdb_len);
+ cpb->prd = cpu_to_le32(pp->pkt_dma + offsetof(struct inic_pkt, prd));
+
+ cpb->device = qc->tf.device;
+ cpb->feature = qc->tf.feature;
+ cpb->nsect = qc->tf.nsect;
+ cpb->lbal = qc->tf.lbal;
+ cpb->lbam = qc->tf.lbam;
+ cpb->lbah = qc->tf.lbah;
+
+ if (qc->tf.flags & ATA_TFLAG_LBA48) {
+ cpb->hob_feature = qc->tf.hob_feature;
+ cpb->hob_nsect = qc->tf.hob_nsect;
+ cpb->hob_lbal = qc->tf.hob_lbal;
+ cpb->hob_lbam = qc->tf.hob_lbam;
+ cpb->hob_lbah = qc->tf.hob_lbah;
+ }
+
+ cpb->command = qc->tf.command;
+ /* don't load ctl - dunno why. it's like that in the initio driver */
+
+ /* setup PRD for CDB */
+ if (is_atapi) {
+ memcpy(pkt->cdb, qc->cdb, ATAPI_CDB_LEN);
+ prd->mad = cpu_to_le32(pp->pkt_dma +
+ offsetof(struct inic_pkt, cdb));
+ prd->len = cpu_to_le16(cdb_len);
+ prd->flags = PRD_CDB | PRD_WRITE;
+ if (!is_data)
+ prd->flags |= PRD_END;
+ prd++;
+ }
+
+ /* setup sg table */
+ if (is_data)
+ inic_fill_sg(prd, qc);
+
+ pp->cpb_tbl[0] = pp->pkt_dma;
+}
+
static unsigned int inic_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
+ void __iomem *port_base = inic_port_base(ap);
- /* ATA IRQ doesn't wait for DMA transfer completion and vice
- * versa. Mask IRQ selectively to detect command completion.
- * Without it, ATA DMA read command can cause data corruption.
- *
- * Something similar might be needed for ATAPI writes. I
- * tried a lot of combinations but couldn't find the solution.
- */
- if (qc->tf.protocol == ATA_PROT_DMA &&
- !(qc->tf.flags & ATA_TFLAG_WRITE))
- inic_set_pirq_mask(ap, PIRQ_MASK_DMA_READ);
- else
- inic_set_pirq_mask(ap, PIRQ_MASK_OTHER);
+ /* fire up the ADMA engine */
+ writew(HCTL_FTHD0, port_base + HOST_CTL);
+ writew(IDMA_CTL_GO, port_base + PORT_IDMA_CTL);
+ writeb(0, port_base + PORT_CPB_PTQFIFO);
+
+ return 0;
+}
+
+static void inic_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
+{
+ void __iomem *port_base = inic_port_base(ap);
+
+ tf->feature = readb(port_base + PORT_TF_FEATURE);
+ tf->nsect = readb(port_base + PORT_TF_NSECT);
+ tf->lbal = readb(port_base + PORT_TF_LBAL);
+ tf->lbam = readb(port_base + PORT_TF_LBAM);
+ tf->lbah = readb(port_base + PORT_TF_LBAH);
+ tf->device = readb(port_base + PORT_TF_DEVICE);
+ tf->command = readb(port_base + PORT_TF_COMMAND);
+}
- /* Issuing a command to yet uninitialized port locks up the
- * controller. Most of the time, this happens for the first
- * command after reset which are ATA and ATAPI IDENTIFYs.
- * Fast fail if stat is 0x7f or 0xff for those commands.
+static bool inic_qc_fill_rtf(struct ata_queued_cmd *qc)
+{
+ struct ata_taskfile *rtf = &qc->result_tf;
+ struct ata_taskfile tf;
+
+ /* FIXME: Except for status and error, result TF access
+ * doesn't work. I tried reading from BAR0/2, CPB and BAR5.
+ * None works regardless of which command interface is used.
+ * For now return true iff status indicates device error.
+ * This means that we're reporting bogus sector for RW
+ * failures. Eeekk....
*/
- if (unlikely(qc->tf.command == ATA_CMD_ID_ATA ||
- qc->tf.command == ATA_CMD_ID_ATAPI)) {
- u8 stat = ap->ops->sff_check_status(ap);
- if (stat == 0x7f || stat == 0xff)
- return AC_ERR_HSM;
- }
+ inic_tf_read(qc->ap, &tf);
- return ata_sff_qc_issue(qc);
+ if (!(tf.command & ATA_ERR))
+ return false;
+
+ rtf->command = tf.command;
+ rtf->feature = tf.feature;
+ return true;
}
static void inic_freeze(struct ata_port *ap)
{
void __iomem *port_base = inic_port_base(ap);
- __inic_set_pirq_mask(ap, PIRQ_MASK_FREEZE);
-
- ap->ops->sff_check_status(ap);
+ writeb(PIRQ_MASK_FREEZE, port_base + PORT_IRQ_MASK);
writeb(0xff, port_base + PORT_IRQ_STAT);
-
- readb(port_base + PORT_IRQ_STAT); /* flush */
}
static void inic_thaw(struct ata_port *ap)
{
void __iomem *port_base = inic_port_base(ap);
- ap->ops->sff_check_status(ap);
writeb(0xff, port_base + PORT_IRQ_STAT);
+ writeb(PIRQ_MASK_DEFAULT, port_base + PORT_IRQ_MASK);
+}
- __inic_set_pirq_mask(ap, PIRQ_MASK_OTHER);
+static int inic_check_ready(struct ata_link *link)
+{
+ void __iomem *port_base = inic_port_base(link->ap);
- readb(port_base + PORT_IRQ_STAT); /* flush */
+ return ata_check_ready(readb(port_base + PORT_TF_COMMAND));
}
/*
@@ -394,17 +616,15 @@ static int inic_hardreset(struct ata_link *link, unsigned int *class,
void __iomem *port_base = inic_port_base(ap);
void __iomem *idma_ctl = port_base + PORT_IDMA_CTL;
const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
- u16 val;
int rc;
/* hammer it into sane state */
inic_reset_port(port_base);
- val = readw(idma_ctl);
- writew(val | IDMA_CTL_RST_ATA, idma_ctl);
+ writew(IDMA_CTL_RST_ATA, idma_ctl);
readw(idma_ctl); /* flush */
msleep(1);
- writew(val & ~IDMA_CTL_RST_ATA, idma_ctl);
+ writew(0, idma_ctl);
rc = sata_link_resume(link, timing, deadline);
if (rc) {
@@ -418,7 +638,7 @@ static int inic_hardreset(struct ata_link *link, unsigned int *class,
struct ata_taskfile tf;
/* wait for link to become ready */
- rc = ata_sff_wait_after_reset(link, 1, deadline);
+ rc = ata_wait_after_reset(link, deadline, inic_check_ready);
/* link occupied, -ENODEV too is an error */
if (rc) {
ata_link_printk(link, KERN_WARNING, "device not ready "
@@ -426,7 +646,7 @@ static int inic_hardreset(struct ata_link *link, unsigned int *class,
return rc;
}
- ata_sff_tf_read(ap, &tf);
+ inic_tf_read(ap, &tf);
*class = ata_dev_classify(&tf);
}
@@ -436,18 +656,8 @@ static int inic_hardreset(struct ata_link *link, unsigned int *class,
static void inic_error_handler(struct ata_port *ap)
{
void __iomem *port_base = inic_port_base(ap);
- struct inic_port_priv *pp = ap->private_data;
- unsigned long flags;
- /* reset PIO HSM and stop DMA engine */
inic_reset_port(port_base);
-
- spin_lock_irqsave(ap->lock, flags);
- ap->hsm_task_state = HSM_ST_IDLE;
- writeb(pp->dfl_prdctl, port_base + PORT_PRD_CTL);
- spin_unlock_irqrestore(ap->lock, flags);
-
- /* PIO and DMA engines have been stopped, perform recovery */
ata_std_error_handler(ap);
}
@@ -458,26 +668,18 @@ static void inic_post_internal_cmd(struct ata_queued_cmd *qc)
inic_reset_port(inic_port_base(qc->ap));
}
-static void inic_dev_config(struct ata_device *dev)
-{
- /* inic can only handle upto LBA28 max sectors */
- if (dev->max_sectors > ATA_MAX_SECTORS)
- dev->max_sectors = ATA_MAX_SECTORS;
-
- if (dev->n_sectors >= 1 << 28) {
- ata_dev_printk(dev, KERN_ERR,
- "ERROR: This driver doesn't support LBA48 yet and may cause\n"
- " data corruption on such devices. Disabling.\n");
- ata_dev_disable(dev);
- }
-}
-
static void init_port(struct ata_port *ap)
{
void __iomem *port_base = inic_port_base(ap);
+ struct inic_port_priv *pp = ap->private_data;
- /* Setup PRD address */
+ /* clear packet and CPB table */
+ memset(pp->pkt, 0, sizeof(struct inic_pkt));
+ memset(pp->cpb_tbl, 0, IDMA_CPB_TBL_SIZE);
+
+ /* setup PRD and CPB lookup table addresses */
writel(ap->prd_dma, port_base + PORT_PRD_ADDR);
+ writel(pp->cpb_tbl_dma, port_base + PORT_CPB_CPBLAR);
}
static int inic_port_resume(struct ata_port *ap)
@@ -488,28 +690,30 @@ static int inic_port_resume(struct ata_port *ap)
static int inic_port_start(struct ata_port *ap)
{
- void __iomem *port_base = inic_port_base(ap);
+ struct device *dev = ap->host->dev;
struct inic_port_priv *pp;
- u8 tmp;
int rc;
/* alloc and initialize private data */
- pp = devm_kzalloc(ap->host->dev, sizeof(*pp), GFP_KERNEL);
+ pp = devm_kzalloc(dev, sizeof(*pp), GFP_KERNEL);
if (!pp)
return -ENOMEM;
ap->private_data = pp;
- /* default PRD_CTL value, DMAEN, WR and START off */
- tmp = readb(port_base + PORT_PRD_CTL);
- tmp &= ~(PRD_CTL_DMAEN | PRD_CTL_WR | PRD_CTL_START);
- pp->dfl_prdctl = tmp;
-
/* Alloc resources */
rc = ata_port_start(ap);
- if (rc) {
- kfree(pp);
+ if (rc)
return rc;
- }
+
+ pp->pkt = dmam_alloc_coherent(dev, sizeof(struct inic_pkt),
+ &pp->pkt_dma, GFP_KERNEL);
+ if (!pp->pkt)
+ return -ENOMEM;
+
+ pp->cpb_tbl = dmam_alloc_coherent(dev, IDMA_CPB_TBL_SIZE,
+ &pp->cpb_tbl_dma, GFP_KERNEL);
+ if (!pp->cpb_tbl)
+ return -ENOMEM;
init_port(ap);
@@ -517,21 +721,18 @@ static int inic_port_start(struct ata_port *ap)
}
static struct ata_port_operations inic_port_ops = {
- .inherits = &ata_sff_port_ops,
+ .inherits = &sata_port_ops,
- .bmdma_setup = inic_bmdma_setup,
- .bmdma_start = inic_bmdma_start,
- .bmdma_stop = inic_bmdma_stop,
- .bmdma_status = inic_bmdma_status,
+ .check_atapi_dma = inic_check_atapi_dma,
+ .qc_prep = inic_qc_prep,
.qc_issue = inic_qc_issue,
+ .qc_fill_rtf = inic_qc_fill_rtf,
.freeze = inic_freeze,
.thaw = inic_thaw,
- .softreset = ATA_OP_NULL, /* softreset is broken */
.hardreset = inic_hardreset,
.error_handler = inic_error_handler,
.post_internal_cmd = inic_post_internal_cmd,
- .dev_config = inic_dev_config,
.scr_read = inic_scr_read,
.scr_write = inic_scr_write,
@@ -541,12 +742,6 @@ static struct ata_port_operations inic_port_ops = {
};
static struct ata_port_info inic_port_info = {
- /* For some reason, ATAPI_PROT_PIO is broken on this
- * controller, and no, PIO_POLLING does't fix it. It somehow
- * manages to report the wrong ireason and ignoring ireason
- * results in machine lock up. Tell libata to always prefer
- * DMA.
- */
.flags = ATA_FLAG_SATA | ATA_FLAG_PIO_DMA,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
@@ -599,7 +794,6 @@ static int inic_pci_device_resume(struct pci_dev *pdev)
{
struct ata_host *host = dev_get_drvdata(&pdev->dev);
struct inic_host_priv *hpriv = host->private_data;
- void __iomem *mmio_base = host->iomap[MMIO_BAR];
int rc;
rc = ata_pci_device_do_resume(pdev);
@@ -607,7 +801,7 @@ static int inic_pci_device_resume(struct pci_dev *pdev)
return rc;
if (pdev->dev.power.power_state.event == PM_EVENT_SUSPEND) {
- rc = init_controller(mmio_base, hpriv->cached_hctl);
+ rc = init_controller(hpriv->mmio_base, hpriv->cached_hctl);
if (rc)
return rc;
}
@@ -625,6 +819,7 @@ static int inic_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
struct ata_host *host;
struct inic_host_priv *hpriv;
void __iomem * const *iomap;
+ int mmio_bar;
int i, rc;
if (!printed_version++)
@@ -638,38 +833,31 @@ static int inic_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
host->private_data = hpriv;
- /* acquire resources and fill host */
+ /* Acquire resources and fill host. Note that PCI and cardbus
+ * use different BARs.
+ */
rc = pcim_enable_device(pdev);
if (rc)
return rc;
- rc = pcim_iomap_regions(pdev, 0x3f, DRV_NAME);
+ if (pci_resource_flags(pdev, MMIO_BAR_PCI) & IORESOURCE_MEM)
+ mmio_bar = MMIO_BAR_PCI;
+ else
+ mmio_bar = MMIO_BAR_CARDBUS;
+
+ rc = pcim_iomap_regions(pdev, 1 << mmio_bar, DRV_NAME);
if (rc)
return rc;
host->iomap = iomap = pcim_iomap_table(pdev);
+ hpriv->mmio_base = iomap[mmio_bar];
+ hpriv->cached_hctl = readw(hpriv->mmio_base + HOST_CTL);
for (i = 0; i < NR_PORTS; i++) {
struct ata_port *ap = host->ports[i];
- struct ata_ioports *port = &ap->ioaddr;
- unsigned int offset = i * PORT_SIZE;
-
- port->cmd_addr = iomap[2 * i];
- port->altstatus_addr =
- port->ctl_addr = (void __iomem *)
- ((unsigned long)iomap[2 * i + 1] | ATA_PCI_CTL_OFS);
- port->scr_addr = iomap[MMIO_BAR] + offset + PORT_SCR;
-
- ata_sff_std_ports(port);
-
- ata_port_pbar_desc(ap, MMIO_BAR, -1, "mmio");
- ata_port_pbar_desc(ap, MMIO_BAR, offset, "port");
- ata_port_desc(ap, "cmd 0x%llx ctl 0x%llx",
- (unsigned long long)pci_resource_start(pdev, 2 * i),
- (unsigned long long)pci_resource_start(pdev, (2 * i + 1)) |
- ATA_PCI_CTL_OFS);
- }
- hpriv->cached_hctl = readw(iomap[MMIO_BAR] + HOST_CTL);
+ ata_port_pbar_desc(ap, mmio_bar, -1, "mmio");
+ ata_port_pbar_desc(ap, mmio_bar, i * PORT_SIZE, "port");
+ }
/* Set dma_mask. This devices doesn't support 64bit addressing. */
rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
@@ -698,7 +886,7 @@ static int inic_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
return rc;
}
- rc = init_controller(iomap[MMIO_BAR], hpriv->cached_hctl);
+ rc = init_controller(hpriv->mmio_base, hpriv->cached_hctl);
if (rc) {
dev_printk(KERN_ERR, &pdev->dev,
"failed to initialize controller\n");
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 842b1a1..bb73b22 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -65,6 +65,7 @@
#include <linux/platform_device.h>
#include <linux/ata_platform.h>
#include <linux/mbus.h>
+#include <linux/bitops.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_device.h>
@@ -91,9 +92,9 @@ enum {
MV_IRQ_COAL_TIME_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xd0),
MV_SATAHC0_REG_BASE = 0x20000,
- MV_FLASH_CTL = 0x1046c,
- MV_GPIO_PORT_CTL = 0x104f0,
- MV_RESET_CFG = 0x180d8,
+ MV_FLASH_CTL_OFS = 0x1046c,
+ MV_GPIO_PORT_CTL_OFS = 0x104f0,
+ MV_RESET_CFG_OFS = 0x180d8,
MV_PCI_REG_SZ = MV_MAJOR_REG_AREA_SZ,
MV_SATAHC_REG_SZ = MV_MAJOR_REG_AREA_SZ,
@@ -147,18 +148,21 @@ enum {
/* PCI interface registers */
PCI_COMMAND_OFS = 0xc00,
+ PCI_COMMAND_MRDTRIG = (1 << 7), /* PCI Master Read Trigger */
PCI_MAIN_CMD_STS_OFS = 0xd30,
STOP_PCI_MASTER = (1 << 2),
PCI_MASTER_EMPTY = (1 << 3),
GLOB_SFT_RST = (1 << 4),
- MV_PCI_MODE = 0xd00,
+ MV_PCI_MODE_OFS = 0xd00,
+ MV_PCI_MODE_MASK = 0x30,
+
MV_PCI_EXP_ROM_BAR_CTL = 0xd2c,
MV_PCI_DISC_TIMER = 0xd04,
MV_PCI_MSI_TRIGGER = 0xc38,
MV_PCI_SERR_MASK = 0xc28,
- MV_PCI_XBAR_TMOUT = 0x1d04,
+ MV_PCI_XBAR_TMOUT_OFS = 0x1d04,
MV_PCI_ERR_LOW_ADDRESS = 0x1d40,
MV_PCI_ERR_HIGH_ADDRESS = 0x1d44,
MV_PCI_ERR_ATTRIBUTE = 0x1d48,
@@ -225,16 +229,18 @@ enum {
PHY_MODE4 = 0x314,
PHY_MODE2 = 0x330,
SATA_IFCTL_OFS = 0x344,
+ SATA_TESTCTL_OFS = 0x348,
SATA_IFSTAT_OFS = 0x34c,
VENDOR_UNIQUE_FIS_OFS = 0x35c,
- FIS_CFG_OFS = 0x360,
- FIS_CFG_SINGLE_SYNC = (1 << 16), /* SYNC on DMA activation */
+ FISCFG_OFS = 0x360,
+ FISCFG_WAIT_DEV_ERR = (1 << 8), /* wait for host on DevErr */
+ FISCFG_SINGLE_SYNC = (1 << 16), /* SYNC on DMA activation */
MV5_PHY_MODE = 0x74,
- MV5_LT_MODE = 0x30,
- MV5_PHY_CTL = 0x0C,
- SATA_INTERFACE_CFG = 0x050,
+ MV5_LTMODE_OFS = 0x30,
+ MV5_PHY_CTL_OFS = 0x0C,
+ SATA_INTERFACE_CFG_OFS = 0x050,
MV_M2_PREAMP_MASK = 0x7e0,
@@ -332,10 +338,16 @@ enum {
EDMA_CMD_OFS = 0x28, /* EDMA command register */
EDMA_EN = (1 << 0), /* enable EDMA */
EDMA_DS = (1 << 1), /* disable EDMA; self-negated */
- ATA_RST = (1 << 2), /* reset trans/link/phy */
+ EDMA_RESET = (1 << 2), /* reset eng/trans/link/phy */
+
+ EDMA_STATUS_OFS = 0x30, /* EDMA engine status */
+ EDMA_STATUS_CACHE_EMPTY = (1 << 6), /* GenIIe command cache empty */
+ EDMA_STATUS_IDLE = (1 << 7), /* GenIIe EDMA enabled/idle */
- EDMA_IORDY_TMOUT = 0x34,
- EDMA_ARB_CFG = 0x38,
+ EDMA_IORDY_TMOUT_OFS = 0x34,
+ EDMA_ARB_CFG_OFS = 0x38,
+
+ EDMA_HALTCOND_OFS = 0x60, /* GenIIe halt conditions */
GEN_II_NCQ_MAX_SECTORS = 256, /* max sects/io on Gen2 w/NCQ */
@@ -350,15 +362,19 @@ enum {
MV_HP_GEN_II = (1 << 7), /* Generation II: 60xx */
MV_HP_GEN_IIE = (1 << 8), /* Generation IIE: 6042/7042 */
MV_HP_PCIE = (1 << 9), /* PCIe bus/regs: 7042 */
+ MV_HP_CUT_THROUGH = (1 << 10), /* can use EDMA cut-through */
/* Port private flags (pp_flags) */
MV_PP_FLAG_EDMA_EN = (1 << 0), /* is EDMA engine enabled? */
MV_PP_FLAG_NCQ_EN = (1 << 1), /* is EDMA set up for NCQ? */
+ MV_PP_FLAG_FBS_EN = (1 << 2), /* is EDMA set up for FBS? */
+ MV_PP_FLAG_DELAYED_EH = (1 << 3), /* delayed dev err handling */
};
#define IS_GEN_I(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_I)
#define IS_GEN_II(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_II)
#define IS_GEN_IIE(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_IIE)
+#define IS_PCIE(hpriv) ((hpriv)->hp_flags & MV_HP_PCIE)
#define HAS_PCI(host) (!((host)->ports[0]->flags & MV_FLAG_SOC))
#define WINDOW_CTRL(i) (0x20030 + ((i) << 4))
@@ -433,6 +449,7 @@ struct mv_port_priv {
unsigned int resp_idx;
u32 pp_flags;
+ unsigned int delayed_eh_pmp_map;
};
struct mv_port_signal {
@@ -479,6 +496,7 @@ static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val);
static int mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
static int mv_port_start(struct ata_port *ap);
static void mv_port_stop(struct ata_port *ap);
+static int mv_qc_defer(struct ata_queued_cmd *qc);
static void mv_qc_prep(struct ata_queued_cmd *qc);
static void mv_qc_prep_iie(struct ata_queued_cmd *qc);
static unsigned int mv_qc_issue(struct ata_queued_cmd *qc);
@@ -527,6 +545,9 @@ static int mv_pmp_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
static int mv_softreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
+static void mv_pmp_error_handler(struct ata_port *ap);
+static void mv_process_crpb_entries(struct ata_port *ap,
+ struct mv_port_priv *pp);
/* .sg_tablesize is (MV_MAX_SG_CT / 2) in the structures below
* because we have to allow room for worst case splitting of
@@ -548,6 +569,7 @@ static struct scsi_host_template mv6_sht = {
static struct ata_port_operations mv5_ops = {
.inherits = &ata_sff_port_ops,
+ .qc_defer = mv_qc_defer,
.qc_prep = mv_qc_prep,
.qc_issue = mv_qc_issue,
@@ -566,7 +588,6 @@ static struct ata_port_operations mv5_ops = {
static struct ata_port_operations mv6_ops = {
.inherits = &mv5_ops,
- .qc_defer = sata_pmp_qc_defer_cmd_switch,
.dev_config = mv6_dev_config,
.scr_read = mv_scr_read,
.scr_write = mv_scr_write,
@@ -574,12 +595,11 @@ static struct ata_port_operations mv6_ops = {
.pmp_hardreset = mv_pmp_hardreset,
.pmp_softreset = mv_softreset,
.softreset = mv_softreset,
- .error_handler = sata_pmp_error_handler,
+ .error_handler = mv_pmp_error_handler,
};
static struct ata_port_operations mv_iie_ops = {
.inherits = &mv6_ops,
- .qc_defer = ata_std_qc_defer, /* FIS-based switching */
.dev_config = ATA_OP_NULL,
.qc_prep = mv_qc_prep_iie,
};
@@ -875,6 +895,29 @@ static void mv_start_dma(struct ata_port *ap, void __iomem *port_mmio,
}
}
+static void mv_wait_for_edma_empty_idle(struct ata_port *ap)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+ const u32 empty_idle = (EDMA_STATUS_CACHE_EMPTY | EDMA_STATUS_IDLE);
+ const int per_loop = 5, timeout = (15 * 1000 / per_loop);
+ int i;
+
+ /*
+ * Wait for the EDMA engine to finish transactions in progress.
+ * No idea what a good "timeout" value might be, but measurements
+ * indicate that it often requires hundreds of microseconds
+ * with two drives in-use. So we use the 15msec value above
+ * as a rough guess at what even more drives might require.
+ */
+ for (i = 0; i < timeout; ++i) {
+ u32 edma_stat = readl(port_mmio + EDMA_STATUS_OFS);
+ if ((edma_stat & empty_idle) == empty_idle)
+ break;
+ udelay(per_loop);
+ }
+ /* ata_port_printk(ap, KERN_INFO, "%s: %u+ usecs\n", __func__, i); */
+}
+
/**
* mv_stop_edma_engine - Disable eDMA engine
* @port_mmio: io base address
@@ -907,6 +950,7 @@ static int mv_stop_edma(struct ata_port *ap)
if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN))
return 0;
pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
+ mv_wait_for_edma_empty_idle(ap);
if (mv_stop_edma_engine(port_mmio)) {
ata_port_printk(ap, KERN_ERR, "Unable to stop eDMA\n");
return -EIO;
@@ -1057,26 +1101,95 @@ static void mv6_dev_config(struct ata_device *adev)
}
}
-static void mv_config_fbs(void __iomem *port_mmio, int enable_fbs)
+static int mv_qc_defer(struct ata_queued_cmd *qc)
{
- u32 old_fcfg, new_fcfg, old_ltmode, new_ltmode;
+ struct ata_link *link = qc->dev->link;
+ struct ata_port *ap = link->ap;
+ struct mv_port_priv *pp = ap->private_data;
+
+ /*
+ * Don't allow new commands if we're in a delayed EH state
+ * for NCQ and/or FIS-based switching.
+ */
+ if (pp->pp_flags & MV_PP_FLAG_DELAYED_EH)
+ return ATA_DEFER_PORT;
/*
- * Various bit settings required for operation
- * in FIS-based switching (fbs) mode on GenIIe:
+ * If the port is completely idle, then allow the new qc.
*/
- old_fcfg = readl(port_mmio + FIS_CFG_OFS);
- old_ltmode = readl(port_mmio + LTMODE_OFS);
- if (enable_fbs) {
- new_fcfg = old_fcfg | FIS_CFG_SINGLE_SYNC;
- new_ltmode = old_ltmode | LTMODE_BIT8;
- } else { /* disable fbs */
- new_fcfg = old_fcfg & ~FIS_CFG_SINGLE_SYNC;
- new_ltmode = old_ltmode & ~LTMODE_BIT8;
- }
- if (new_fcfg != old_fcfg)
- writelfl(new_fcfg, port_mmio + FIS_CFG_OFS);
+ if (ap->nr_active_links == 0)
+ return 0;
+
+ if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) {
+ /*
+ * The port is operating in host queuing mode (EDMA).
+ * It can accomodate a new qc if the qc protocol
+ * is compatible with the current host queue mode.
+ */
+ if (pp->pp_flags & MV_PP_FLAG_NCQ_EN) {
+ /*
+ * The host queue (EDMA) is in NCQ mode.
+ * If the new qc is also an NCQ command,
+ * then allow the new qc.
+ */
+ if (qc->tf.protocol == ATA_PROT_NCQ)
+ return 0;
+ } else {
+ /*
+ * The host queue (EDMA) is in non-NCQ, DMA mode.
+ * If the new qc is also a non-NCQ, DMA command,
+ * then allow the new qc.
+ */
+ if (qc->tf.protocol == ATA_PROT_DMA)
+ return 0;
+ }
+ }
+ return ATA_DEFER_PORT;
+}
+
+static void mv_config_fbs(void __iomem *port_mmio, int want_ncq, int want_fbs)
+{
+ u32 new_fiscfg, old_fiscfg;
+ u32 new_ltmode, old_ltmode;
+ u32 new_haltcond, old_haltcond;
+
+ old_fiscfg = readl(port_mmio + FISCFG_OFS);
+ old_ltmode = readl(port_mmio + LTMODE_OFS);
+ old_haltcond = readl(port_mmio + EDMA_HALTCOND_OFS);
+
+ new_fiscfg = old_fiscfg & ~(FISCFG_SINGLE_SYNC | FISCFG_WAIT_DEV_ERR);
+ new_ltmode = old_ltmode & ~LTMODE_BIT8;
+ new_haltcond = old_haltcond | EDMA_ERR_DEV;
+
+ if (want_fbs) {
+ new_fiscfg = old_fiscfg | FISCFG_SINGLE_SYNC;
+ new_ltmode = old_ltmode | LTMODE_BIT8;
+ if (want_ncq)
+ new_haltcond &= ~EDMA_ERR_DEV;
+ else
+ new_fiscfg |= FISCFG_WAIT_DEV_ERR;
+ }
+
+ if (new_fiscfg != old_fiscfg)
+ writelfl(new_fiscfg, port_mmio + FISCFG_OFS);
if (new_ltmode != old_ltmode)
writelfl(new_ltmode, port_mmio + LTMODE_OFS);
+ if (new_haltcond != old_haltcond)
+ writelfl(new_haltcond, port_mmio + EDMA_HALTCOND_OFS);
+}
+
+static void mv_60x1_errata_sata25(struct ata_port *ap, int want_ncq)
+{
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ u32 old, new;
+
+ /* workaround for 88SX60x1 FEr SATA#25 (part 1) */
+ old = readl(hpriv->base + MV_GPIO_PORT_CTL_OFS);
+ if (want_ncq)
+ new = old | (1 << 22);
+ else
+ new = old & ~(1 << 22);
+ if (new != old)
+ writel(new, hpriv->base + MV_GPIO_PORT_CTL_OFS);
}
static void mv_edma_cfg(struct ata_port *ap, int want_ncq)
@@ -1088,25 +1201,40 @@ static void mv_edma_cfg(struct ata_port *ap, int want_ncq)
/* set up non-NCQ EDMA configuration */
cfg = EDMA_CFG_Q_DEPTH; /* always 0x1f for *all* chips */
+ pp->pp_flags &= ~MV_PP_FLAG_FBS_EN;
if (IS_GEN_I(hpriv))
cfg |= (1 << 8); /* enab config burst size mask */
- else if (IS_GEN_II(hpriv))
+ else if (IS_GEN_II(hpriv)) {
cfg |= EDMA_CFG_RD_BRST_EXT | EDMA_CFG_WR_BUFF_LEN;
+ mv_60x1_errata_sata25(ap, want_ncq);
- else if (IS_GEN_IIE(hpriv)) {
- cfg |= (1 << 23); /* do not mask PM field in rx'd FIS */
- cfg |= (1 << 22); /* enab 4-entry host queue cache */
- cfg |= (1 << 18); /* enab early completion */
- cfg |= (1 << 17); /* enab cut-through (dis stor&forwrd) */
+ } else if (IS_GEN_IIE(hpriv)) {
+ int want_fbs = sata_pmp_attached(ap);
+ /*
+ * Possible future enhancement:
+ *
+ * The chip can use FBS with non-NCQ, if we allow it,
+ * But first we need to have the error handling in place
+ * for this mode (datasheet section 7.3.15.4.2.3).
+ * So disallow non-NCQ FBS for now.
+ */
+ want_fbs &= want_ncq;
+
+ mv_config_fbs(port_mmio, want_ncq, want_fbs);
- if (want_ncq && sata_pmp_attached(ap)) {
+ if (want_fbs) {
+ pp->pp_flags |= MV_PP_FLAG_FBS_EN;
cfg |= EDMA_CFG_EDMA_FBS; /* FIS-based switching */
- mv_config_fbs(port_mmio, 1);
- } else {
- mv_config_fbs(port_mmio, 0);
}
+
+ cfg |= (1 << 23); /* do not mask PM field in rx'd FIS */
+ cfg |= (1 << 22); /* enab 4-entry host queue cache */
+ if (HAS_PCI(ap->host))
+ cfg |= (1 << 18); /* enab early completion */
+ if (hpriv->hp_flags & MV_HP_CUT_THROUGH)
+ cfg |= (1 << 17); /* enab cut-thru (dis stor&forwrd) */
}
if (want_ncq) {
@@ -1483,25 +1611,186 @@ static struct ata_queued_cmd *mv_get_active_qc(struct ata_port *ap)
return qc;
}
-static void mv_unexpected_intr(struct ata_port *ap)
+static void mv_pmp_error_handler(struct ata_port *ap)
{
+ unsigned int pmp, pmp_map;
struct mv_port_priv *pp = ap->private_data;
- struct ata_eh_info *ehi = &ap->link.eh_info;
- char *when = "";
+ if (pp->pp_flags & MV_PP_FLAG_DELAYED_EH) {
+ /*
+ * Perform NCQ error analysis on failed PMPs
+ * before we freeze the port entirely.
+ *
+ * The failed PMPs are marked earlier by mv_pmp_eh_prep().
+ */
+ pmp_map = pp->delayed_eh_pmp_map;
+ pp->pp_flags &= ~MV_PP_FLAG_DELAYED_EH;
+ for (pmp = 0; pmp_map != 0; pmp++) {
+ unsigned int this_pmp = (1 << pmp);
+ if (pmp_map & this_pmp) {
+ struct ata_link *link = &ap->pmp_link[pmp];
+ pmp_map &= ~this_pmp;
+ ata_eh_analyze_ncq_error(link);
+ }
+ }
+ ata_port_freeze(ap);
+ }
+ sata_pmp_error_handler(ap);
+}
+
+static unsigned int mv_get_err_pmp_map(struct ata_port *ap)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+
+ return readl(port_mmio + SATA_TESTCTL_OFS) >> 16;
+}
+
+static void mv_pmp_eh_prep(struct ata_port *ap, unsigned int pmp_map)
+{
+ struct ata_eh_info *ehi;
+ unsigned int pmp;
+
+ /*
+ * Initialize EH info for PMPs which saw device errors
+ */
+ ehi = &ap->link.eh_info;
+ for (pmp = 0; pmp_map != 0; pmp++) {
+ unsigned int this_pmp = (1 << pmp);
+ if (pmp_map & this_pmp) {
+ struct ata_link *link = &ap->pmp_link[pmp];
+
+ pmp_map &= ~this_pmp;
+ ehi = &link->eh_info;
+ ata_ehi_clear_desc(ehi);
+ ata_ehi_push_desc(ehi, "dev err");
+ ehi->err_mask |= AC_ERR_DEV;
+ ehi->action |= ATA_EH_RESET;
+ ata_link_abort(link);
+ }
+ }
+}
+
+static int mv_handle_fbs_ncq_dev_err(struct ata_port *ap)
+{
+ struct mv_port_priv *pp = ap->private_data;
+ int failed_links;
+ unsigned int old_map, new_map;
+
+ /*
+ * Device error during FBS+NCQ operation:
+ *
+ * Set a port flag to prevent further I/O being enqueued.
+ * Leave the EDMA running to drain outstanding commands from this port.
+ * Perform the post-mortem/EH only when all responses are complete.
+ * Follow recovery sequence from 6042/7042 datasheet (7.3.15.4.2.2).
+ */
+ if (!(pp->pp_flags & MV_PP_FLAG_DELAYED_EH)) {
+ pp->pp_flags |= MV_PP_FLAG_DELAYED_EH;
+ pp->delayed_eh_pmp_map = 0;
+ }
+ old_map = pp->delayed_eh_pmp_map;
+ new_map = old_map | mv_get_err_pmp_map(ap);
+
+ if (old_map != new_map) {
+ pp->delayed_eh_pmp_map = new_map;
+ mv_pmp_eh_prep(ap, new_map & ~old_map);
+ }
+ failed_links = hweight16(new_map);
+
+ ata_port_printk(ap, KERN_INFO, "%s: pmp_map=%04x qc_map=%04x "
+ "failed_links=%d nr_active_links=%d\n",
+ __func__, pp->delayed_eh_pmp_map,
+ ap->qc_active, failed_links,
+ ap->nr_active_links);
+
+ if (ap->nr_active_links <= failed_links) {
+ mv_process_crpb_entries(ap, pp);
+ mv_stop_edma(ap);
+ mv_eh_freeze(ap);
+ ata_port_printk(ap, KERN_INFO, "%s: done\n", __func__);
+ return 1; /* handled */
+ }
+ ata_port_printk(ap, KERN_INFO, "%s: waiting\n", __func__);
+ return 1; /* handled */
+}
+
+static int mv_handle_fbs_non_ncq_dev_err(struct ata_port *ap)
+{
/*
- * We got a device interrupt from something that
- * was supposed to be using EDMA or polling.
+ * Possible future enhancement:
+ *
+ * FBS+non-NCQ operation is not yet implemented.
+ * See related notes in mv_edma_cfg().
+ *
+ * Device error during FBS+non-NCQ operation:
+ *
+ * We need to snapshot the shadow registers for each failed command.
+ * Follow recovery sequence from 6042/7042 datasheet (7.3.15.4.2.3).
*/
+ return 0; /* not handled */
+}
+
+static int mv_handle_dev_err(struct ata_port *ap, u32 edma_err_cause)
+{
+ struct mv_port_priv *pp = ap->private_data;
+
+ if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN))
+ return 0; /* EDMA was not active: not handled */
+ if (!(pp->pp_flags & MV_PP_FLAG_FBS_EN))
+ return 0; /* FBS was not active: not handled */
+
+ if (!(edma_err_cause & EDMA_ERR_DEV))
+ return 0; /* non DEV error: not handled */
+ edma_err_cause &= ~EDMA_ERR_IRQ_TRANSIENT;
+ if (edma_err_cause & ~(EDMA_ERR_DEV | EDMA_ERR_SELF_DIS))
+ return 0; /* other problems: not handled */
+
+ if (pp->pp_flags & MV_PP_FLAG_NCQ_EN) {
+ /*
+ * EDMA should NOT have self-disabled for this case.
+ * If it did, then something is wrong elsewhere,
+ * and we cannot handle it here.
+ */
+ if (edma_err_cause & EDMA_ERR_SELF_DIS) {
+ ata_port_printk(ap, KERN_WARNING,
+ "%s: err_cause=0x%x pp_flags=0x%x\n",
+ __func__, edma_err_cause, pp->pp_flags);
+ return 0; /* not handled */
+ }
+ return mv_handle_fbs_ncq_dev_err(ap);
+ } else {
+ /*
+ * EDMA should have self-disabled for this case.
+ * If it did not, then something is wrong elsewhere,
+ * and we cannot handle it here.
+ */
+ if (!(edma_err_cause & EDMA_ERR_SELF_DIS)) {
+ ata_port_printk(ap, KERN_WARNING,
+ "%s: err_cause=0x%x pp_flags=0x%x\n",
+ __func__, edma_err_cause, pp->pp_flags);
+ return 0; /* not handled */
+ }
+ return mv_handle_fbs_non_ncq_dev_err(ap);
+ }
+ return 0; /* not handled */
+}
+
+static void mv_unexpected_intr(struct ata_port *ap, int edma_was_enabled)
+{
+ struct ata_eh_info *ehi = &ap->link.eh_info;
+ char *when = "idle";
+
ata_ehi_clear_desc(ehi);
- if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) {
- when = " while EDMA enabled";
+ if (!ap || (ap->flags & ATA_FLAG_DISABLED)) {
+ when = "disabled";
+ } else if (edma_was_enabled) {
+ when = "EDMA enabled";
} else {
struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->link.active_tag);
if (qc && (qc->tf.flags & ATA_TFLAG_POLLING))
- when = " while polling";
+ when = "polling";
}
- ata_ehi_push_desc(ehi, "unexpected device interrupt%s", when);
+ ata_ehi_push_desc(ehi, "unexpected device interrupt while %s", when);
ehi->err_mask |= AC_ERR_OTHER;
ehi->action |= ATA_EH_RESET;
ata_port_freeze(ap);
@@ -1519,7 +1808,7 @@ static void mv_unexpected_intr(struct ata_port *ap)
* LOCKING:
* Inherited from caller.
*/
-static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
+static void mv_err_intr(struct ata_port *ap)
{
void __iomem *port_mmio = mv_ap_base(ap);
u32 edma_err_cause, eh_freeze_mask, serr = 0;
@@ -1527,24 +1816,42 @@ static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
struct mv_host_priv *hpriv = ap->host->private_data;
unsigned int action = 0, err_mask = 0;
struct ata_eh_info *ehi = &ap->link.eh_info;
-
- ata_ehi_clear_desc(ehi);
+ struct ata_queued_cmd *qc;
+ int abort = 0;
/*
- * Read and clear the err_cause bits. This won't actually
- * clear for some errors (eg. SError), but we will be doing
- * a hard reset in those cases regardless, which *will* clear it.
+ * Read and clear the SError and err_cause bits.
*/
+ sata_scr_read(&ap->link, SCR_ERROR, &serr);
+ sata_scr_write_flush(&ap->link, SCR_ERROR, serr);
+
edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
writelfl(~edma_err_cause, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
- ata_ehi_push_desc(ehi, "edma_err_cause=%08x", edma_err_cause);
+ ata_port_printk(ap, KERN_INFO, "%s: err_cause=%08x pp_flags=0x%x\n",
+ __func__, edma_err_cause, pp->pp_flags);
+
+ if (edma_err_cause & EDMA_ERR_DEV) {
+ /*
+ * Device errors during FIS-based switching operation
+ * require special handling.
+ */
+ if (mv_handle_dev_err(ap, edma_err_cause))
+ return;
+ }
+ qc = mv_get_active_qc(ap);
+ ata_ehi_clear_desc(ehi);
+ ata_ehi_push_desc(ehi, "edma_err_cause=%08x pp_flags=%08x",
+ edma_err_cause, pp->pp_flags);
/*
* All generations share these EDMA error cause bits:
*/
- if (edma_err_cause & EDMA_ERR_DEV)
+ if (edma_err_cause & EDMA_ERR_DEV) {
err_mask |= AC_ERR_DEV;
+ action |= ATA_EH_RESET;
+ ata_ehi_push_desc(ehi, "dev error");
+ }
if (edma_err_cause & (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR |
EDMA_ERR_CRQB_PAR | EDMA_ERR_CRPB_PAR |
EDMA_ERR_INTRL_PAR)) {
@@ -1576,13 +1883,6 @@ static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
ata_ehi_push_desc(ehi, "EDMA self-disable");
}
if (edma_err_cause & EDMA_ERR_SERR) {
- /*
- * Ensure that we read our own SCR, not a pmp link SCR:
- */
- ap->ops->scr_read(ap, SCR_ERROR, &serr);
- /*
- * Don't clear SError here; leave it for libata-eh:
- */
ata_ehi_push_desc(ehi, "SError=%08x", serr);
err_mask |= AC_ERR_ATA_BUS;
action |= ATA_EH_RESET;
@@ -1602,10 +1902,29 @@ static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
else
ehi->err_mask |= err_mask;
- if (edma_err_cause & eh_freeze_mask)
+ if (err_mask == AC_ERR_DEV) {
+ /*
+ * Cannot do ata_port_freeze() here,
+ * because it would kill PIO access,
+ * which is needed for further diagnosis.
+ */
+ mv_eh_freeze(ap);
+ abort = 1;
+ } else if (edma_err_cause & eh_freeze_mask) {
+ /*
+ * Note to self: ata_port_freeze() calls ata_port_abort()
+ */
ata_port_freeze(ap);
- else
- ata_port_abort(ap);
+ } else {
+ abort = 1;
+ }
+
+ if (abort) {
+ if (qc)
+ ata_link_abort(qc->dev->link);
+ else
+ ata_port_abort(ap);
+ }
}
static void mv_process_crpb_response(struct ata_port *ap,
@@ -1632,8 +1951,9 @@ static void mv_process_crpb_response(struct ata_port *ap,
}
}
ata_status = edma_status >> CRPB_FLAG_STATUS_SHIFT;
- qc->err_mask |= ac_err_mask(ata_status);
- ata_qc_complete(qc);
+ if (!ac_err_mask(ata_status))
+ ata_qc_complete(qc);
+ /* else: leave it for mv_err_intr() */
} else {
ata_port_printk(ap, KERN_ERR, "%s: no qc for tag=%d\n",
__func__, tag);
@@ -1677,6 +1997,44 @@ static void mv_process_crpb_entries(struct ata_port *ap, struct mv_port_priv *pp
port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
}
+static void mv_port_intr(struct ata_port *ap, u32 port_cause)
+{
+ struct mv_port_priv *pp;
+ int edma_was_enabled;
+
+ if (!ap || (ap->flags & ATA_FLAG_DISABLED)) {
+ mv_unexpected_intr(ap, 0);
+ return;
+ }
+ /*
+ * Grab a snapshot of the EDMA_EN flag setting,
+ * so that we have a consistent view for this port,
+ * even if something we call of our routines changes it.
+ */
+ pp = ap->private_data;
+ edma_was_enabled = (pp->pp_flags & MV_PP_FLAG_EDMA_EN);
+ /*
+ * Process completed CRPB response(s) before other events.
+ */
+ if (edma_was_enabled && (port_cause & DONE_IRQ)) {
+ mv_process_crpb_entries(ap, pp);
+ if (pp->pp_flags & MV_PP_FLAG_DELAYED_EH)
+ mv_handle_fbs_ncq_dev_err(ap);
+ }
+ /*
+ * Handle chip-reported errors, or continue on to handle PIO.
+ */
+ if (unlikely(port_cause & ERR_IRQ)) {
+ mv_err_intr(ap);
+ } else if (!edma_was_enabled) {
+ struct ata_queued_cmd *qc = mv_get_active_qc(ap);
+ if (qc)
+ ata_sff_host_intr(ap, qc);
+ else
+ mv_unexpected_intr(ap, edma_was_enabled);
+ }
+}
+
/**
* mv_host_intr - Handle all interrupts on the given host controller
* @host: host specific structure
@@ -1688,66 +2046,58 @@ static void mv_process_crpb_entries(struct ata_port *ap, struct mv_port_priv *pp
static int mv_host_intr(struct ata_host *host, u32 main_irq_cause)
{
struct mv_host_priv *hpriv = host->private_data;
- void __iomem *mmio = hpriv->base, *hc_mmio = NULL;
- u32 hc_irq_cause = 0;
+ void __iomem *mmio = hpriv->base, *hc_mmio;
unsigned int handled = 0, port;
for (port = 0; port < hpriv->n_ports; port++) {
struct ata_port *ap = host->ports[port];
- struct mv_port_priv *pp;
- unsigned int shift, hardport, port_cause;
- /*
- * When we move to the second hc, flag our cached
- * copies of hc_mmio (and hc_irq_cause) as invalid again.
- */
- if (port == MV_PORTS_PER_HC)
- hc_mmio = NULL;
- /*
- * Do nothing if port is not interrupting or is disabled:
- */
+ unsigned int p, shift, hardport, port_cause;
+
MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport);
- port_cause = (main_irq_cause >> shift) & (DONE_IRQ | ERR_IRQ);
- if (!port_cause || !ap || (ap->flags & ATA_FLAG_DISABLED))
- continue;
/*
- * Each hc within the host has its own hc_irq_cause register.
- * We defer reading it until we know we need it, right now:
- *
- * FIXME later: we don't really need to read this register
- * (some logic changes required below if we go that way),
- * because it doesn't tell us anything new. But we do need
- * to write to it, outside the top of this loop,
- * to reset the interrupt triggers for next time.
+ * Each hc within the host has its own hc_irq_cause register,
+ * where the interrupting ports bits get ack'd.
*/
- if (!hc_mmio) {
+ if (hardport == 0) { /* first port on this hc ? */
+ u32 hc_cause = (main_irq_cause >> shift) & HC0_IRQ_PEND;
+ u32 port_mask, ack_irqs;
+ /*
+ * Skip this entire hc if nothing pending for any ports
+ */
+ if (!hc_cause) {
+ port += MV_PORTS_PER_HC - 1;
+ continue;
+ }
+ /*
+ * We don't need/want to read the hc_irq_cause register,
+ * because doing so hurts performance, and
+ * main_irq_cause already gives us everything we need.
+ *
+ * But we do have to *write* to the hc_irq_cause to ack
+ * the ports that we are handling this time through.
+ *
+ * This requires that we create a bitmap for those
+ * ports which interrupted us, and use that bitmap
+ * to ack (only) those ports via hc_irq_cause.
+ */
+ ack_irqs = 0;
+ for (p = 0; p < MV_PORTS_PER_HC; ++p) {
+ if ((port + p) >= hpriv->n_ports)
+ break;
+ port_mask = (DONE_IRQ | ERR_IRQ) << (p * 2);
+ if (hc_cause & port_mask)
+ ack_irqs |= (DMA_IRQ | DEV_IRQ) << p;
+ }
hc_mmio = mv_hc_base_from_port(mmio, port);
- hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
- writelfl(~hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
+ writelfl(~ack_irqs, hc_mmio + HC_IRQ_CAUSE_OFS);
handled = 1;
}
/*
- * Process completed CRPB response(s) before other events.
- */
- pp = ap->private_data;
- if (hc_irq_cause & (DMA_IRQ << hardport)) {
- if (pp->pp_flags & MV_PP_FLAG_EDMA_EN)
- mv_process_crpb_entries(ap, pp);
- }
- /*
- * Handle chip-reported errors, or continue on to handle PIO.
+ * Handle interrupts signalled for this port:
*/
- if (unlikely(port_cause & ERR_IRQ)) {
- mv_err_intr(ap, mv_get_active_qc(ap));
- } else if (hc_irq_cause & (DEV_IRQ << hardport)) {
- if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN)) {
- struct ata_queued_cmd *qc = mv_get_active_qc(ap);
- if (qc) {
- ata_sff_host_intr(ap, qc);
- continue;
- }
- }
- mv_unexpected_intr(ap);
- }
+ port_cause = (main_irq_cause >> shift) & (DONE_IRQ | ERR_IRQ);
+ if (port_cause)
+ mv_port_intr(ap, port_cause);
}
return handled;
}
@@ -1894,7 +2244,7 @@ static void mv5_reset_bus(struct ata_host *host, void __iomem *mmio)
static void mv5_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio)
{
- writel(0x0fcfffff, mmio + MV_FLASH_CTL);
+ writel(0x0fcfffff, mmio + MV_FLASH_CTL_OFS);
}
static void mv5_read_preamp(struct mv_host_priv *hpriv, int idx,
@@ -1913,7 +2263,7 @@ static void mv5_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio)
{
u32 tmp;
- writel(0, mmio + MV_GPIO_PORT_CTL);
+ writel(0, mmio + MV_GPIO_PORT_CTL_OFS);
/* FIXME: handle MV_HP_ERRATA_50XXB2 errata */
@@ -1931,14 +2281,14 @@ static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
int fix_apm_sq = (hpriv->hp_flags & MV_HP_ERRATA_50XXB0);
if (fix_apm_sq) {
- tmp = readl(phy_mmio + MV5_LT_MODE);
+ tmp = readl(phy_mmio + MV5_LTMODE_OFS);
tmp |= (1 << 19);
- writel(tmp, phy_mmio + MV5_LT_MODE);
+ writel(tmp, phy_mmio + MV5_LTMODE_OFS);
- tmp = readl(phy_mmio + MV5_PHY_CTL);
+ tmp = readl(phy_mmio + MV5_PHY_CTL_OFS);
tmp &= ~0x3;
tmp |= 0x1;
- writel(tmp, phy_mmio + MV5_PHY_CTL);
+ writel(tmp, phy_mmio + MV5_PHY_CTL_OFS);
}
tmp = readl(phy_mmio + MV5_PHY_MODE);
@@ -1956,11 +2306,6 @@ static void mv5_reset_hc_port(struct mv_host_priv *hpriv, void __iomem *mmio,
{
void __iomem *port_mmio = mv_port_base(mmio, port);
- /*
- * The datasheet warns against setting ATA_RST when EDMA is active
- * (but doesn't say what the problem might be). So we first try
- * to disable the EDMA engine before doing the ATA_RST operation.
- */
mv_reset_channel(hpriv, mmio, port);
ZERO(0x028); /* command */
@@ -1975,7 +2320,7 @@ static void mv5_reset_hc_port(struct mv_host_priv *hpriv, void __iomem *mmio,
ZERO(0x024); /* respq outp */
ZERO(0x020); /* respq inp */
ZERO(0x02c); /* test control */
- writel(0xbc, port_mmio + EDMA_IORDY_TMOUT);
+ writel(0xbc, port_mmio + EDMA_IORDY_TMOUT_OFS);
}
#undef ZERO
@@ -2021,13 +2366,13 @@ static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio)
struct mv_host_priv *hpriv = host->private_data;
u32 tmp;
- tmp = readl(mmio + MV_PCI_MODE);
+ tmp = readl(mmio + MV_PCI_MODE_OFS);
tmp &= 0xff00ffff;
- writel(tmp, mmio + MV_PCI_MODE);
+ writel(tmp, mmio + MV_PCI_MODE_OFS);
ZERO(MV_PCI_DISC_TIMER);
ZERO(MV_PCI_MSI_TRIGGER);
- writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT);
+ writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT_OFS);
ZERO(PCI_HC_MAIN_IRQ_MASK_OFS);
ZERO(MV_PCI_SERR_MASK);
ZERO(hpriv->irq_cause_ofs);
@@ -2045,10 +2390,10 @@ static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio)
mv5_reset_flash(hpriv, mmio);
- tmp = readl(mmio + MV_GPIO_PORT_CTL);
+ tmp = readl(mmio + MV_GPIO_PORT_CTL_OFS);
tmp &= 0x3;
tmp |= (1 << 5) | (1 << 6);
- writel(tmp, mmio + MV_GPIO_PORT_CTL);
+ writel(tmp, mmio + MV_GPIO_PORT_CTL_OFS);
}
/**
@@ -2121,7 +2466,7 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx,
void __iomem *port_mmio;
u32 tmp;
- tmp = readl(mmio + MV_RESET_CFG);
+ tmp = readl(mmio + MV_RESET_CFG_OFS);
if ((tmp & (1 << 0)) == 0) {
hpriv->signal[idx].amps = 0x7 << 8;
hpriv->signal[idx].pre = 0x1 << 5;
@@ -2137,7 +2482,7 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx,
static void mv6_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio)
{
- writel(0x00000060, mmio + MV_GPIO_PORT_CTL);
+ writel(0x00000060, mmio + MV_GPIO_PORT_CTL_OFS);
}
static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
@@ -2235,11 +2580,6 @@ static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv,
{
void __iomem *port_mmio = mv_port_base(mmio, port);
- /*
- * The datasheet warns against setting ATA_RST when EDMA is active
- * (but doesn't say what the problem might be). So we first try
- * to disable the EDMA engine before doing the ATA_RST operation.
- */
mv_reset_channel(hpriv, mmio, port);
ZERO(0x028); /* command */
@@ -2254,7 +2594,7 @@ static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv,
ZERO(0x024); /* respq outp */
ZERO(0x020); /* respq inp */
ZERO(0x02c); /* test control */
- writel(0xbc, port_mmio + EDMA_IORDY_TMOUT);
+ writel(0xbc, port_mmio + EDMA_IORDY_TMOUT_OFS);
}
#undef ZERO
@@ -2297,38 +2637,39 @@ static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio)
return;
}
-static void mv_setup_ifctl(void __iomem *port_mmio, int want_gen2i)
+static void mv_setup_ifcfg(void __iomem *port_mmio, int want_gen2i)
{
- u32 ifctl = readl(port_mmio + SATA_INTERFACE_CFG);
+ u32 ifcfg = readl(port_mmio + SATA_INTERFACE_CFG_OFS);
- ifctl = (ifctl & 0xf7f) | 0x9b1000; /* from chip spec */
+ ifcfg = (ifcfg & 0xf7f) | 0x9b1000; /* from chip spec */
if (want_gen2i)
- ifctl |= (1 << 7); /* enable gen2i speed */
- writelfl(ifctl, port_mmio + SATA_INTERFACE_CFG);
+ ifcfg |= (1 << 7); /* enable gen2i speed */
+ writelfl(ifcfg, port_mmio + SATA_INTERFACE_CFG_OFS);
}
-/*
- * Caller must ensure that EDMA is not active,
- * by first doing mv_stop_edma() where needed.
- */
static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int port_no)
{
void __iomem *port_mmio = mv_port_base(mmio, port_no);
+ /*
+ * The datasheet warns against setting EDMA_RESET when EDMA is active
+ * (but doesn't say what the problem might be). So we first try
+ * to disable the EDMA engine before doing the EDMA_RESET operation.
+ */
mv_stop_edma_engine(port_mmio);
- writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS);
+ writelfl(EDMA_RESET, port_mmio + EDMA_CMD_OFS);
if (!IS_GEN_I(hpriv)) {
- /* Enable 3.0gb/s link speed */
- mv_setup_ifctl(port_mmio, 1);
+ /* Enable 3.0gb/s link speed: this survives EDMA_RESET */
+ mv_setup_ifcfg(port_mmio, 1);
}
/*
- * Strobing ATA_RST here causes a hard reset of the SATA transport,
+ * Strobing EDMA_RESET here causes a hard reset of the SATA transport,
* link, and physical layers. It resets all SATA interface registers
* (except for SATA_INTERFACE_CFG), and issues a COMRESET to the dev.
*/
- writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS);
+ writelfl(EDMA_RESET, port_mmio + EDMA_CMD_OFS);
udelay(25); /* allow reset propagation */
writelfl(0, port_mmio + EDMA_CMD_OFS);
@@ -2392,7 +2733,7 @@ static int mv_hardreset(struct ata_link *link, unsigned int *class,
sata_scr_read(link, SCR_STATUS, &sstatus);
if (!IS_GEN_I(hpriv) && ++attempts >= 5 && sstatus == 0x121) {
/* Force 1.5gb/s link speed and try again */
- mv_setup_ifctl(mv_ap_base(ap), 0);
+ mv_setup_ifcfg(mv_ap_base(ap), 0);
if (time_after(jiffies + HZ, deadline))
extra = HZ; /* only extend it once, max */
}
@@ -2493,6 +2834,34 @@ static void mv_port_init(struct ata_ioports *port, void __iomem *port_mmio)
readl(port_mmio + EDMA_ERR_IRQ_MASK_OFS));
}
+static unsigned int mv_in_pcix_mode(struct ata_host *host)
+{
+ struct mv_host_priv *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->base;
+ u32 reg;
+
+ if (!HAS_PCI(host) || !IS_PCIE(hpriv))
+ return 0; /* not PCI-X capable */
+ reg = readl(mmio + MV_PCI_MODE_OFS);
+ if ((reg & MV_PCI_MODE_MASK) == 0)
+ return 0; /* conventional PCI mode */
+ return 1; /* chip is in PCI-X mode */
+}
+
+static int mv_pci_cut_through_okay(struct ata_host *host)
+{
+ struct mv_host_priv *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->base;
+ u32 reg;
+
+ if (!mv_in_pcix_mode(host)) {
+ reg = readl(mmio + PCI_COMMAND_OFS);
+ if (reg & PCI_COMMAND_MRDTRIG)
+ return 0; /* not okay */
+ }
+ return 1; /* okay */
+}
+
static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
{
struct pci_dev *pdev = to_pci_dev(host->dev);
@@ -2560,7 +2929,7 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
break;
case chip_7042:
- hp_flags |= MV_HP_PCIE;
+ hp_flags |= MV_HP_PCIE | MV_HP_CUT_THROUGH;
if (pdev->vendor == PCI_VENDOR_ID_TTI &&
(pdev->device == 0x2300 || pdev->device == 0x2310))
{
@@ -2590,9 +2959,12 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
" and avoid the final two gigabytes on"
" all RocketRAID BIOS initialized drives.\n");
}
+ /* drop through */
case chip_6042:
hpriv->ops = &mv6xxx_ops;
hp_flags |= MV_HP_GEN_IIE;
+ if (board_idx == chip_6042 && mv_pci_cut_through_okay(host))
+ hp_flags |= MV_HP_CUT_THROUGH;
switch (pdev->revision) {
case 0x0:
diff --git a/include/linux/libata.h b/include/linux/libata.h
index d1dfe87..7e206da 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1039,6 +1039,7 @@ extern void ata_eh_thaw_port(struct ata_port *ap);
extern void ata_eh_qc_complete(struct ata_queued_cmd *qc);
extern void ata_eh_qc_retry(struct ata_queued_cmd *qc);
+extern void ata_eh_analyze_ncq_error(struct ata_link *link);
extern void ata_do_eh(struct ata_port *ap, ata_prereset_fn_t prereset,
ata_reset_fn_t softreset, ata_reset_fn_t hardreset,
@@ -1381,6 +1382,21 @@ static inline struct ata_port *ata_shost_to_port(struct Scsi_Host *host)
return *(struct ata_port **)&host->hostdata[0];
}
+static inline int ata_check_ready(u8 status)
+{
+ /* Some controllers report 0x77 or 0x7f during intermediate
+ * not-ready stages.
+ */
+ if (status == 0x77 || status == 0x7f)
+ return 0;
+
+ /* 0xff indicates either no device or device not ready */
+ if (status == 0xff)
+ return -ENODEV;
+
+ return !(status & ATA_BUSY);
+}
+
/**************************************************************************
* PMP - drivers/ata/libata-pmp.c
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2008-04-29 6:25 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2008-04-29 6:25 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/Kconfig | 8 +-
drivers/ata/Makefile | 2 +-
drivers/ata/libata-scsi.c | 507 +++++++---------------
drivers/ata/libata.h | 28 --
drivers/ata/pata_bf54x.c | 124 +++++-
drivers/ata/{pata_rb500_cf.c => pata_rb532_cf.c} | 78 ++--
drivers/ata/sata_mv.c | 77 ++--
7 files changed, 365 insertions(+), 459 deletions(-)
rename drivers/ata/{pata_rb500_cf.c => pata_rb532_cf.c} (72%)
Mark Lord (1):
sata_mv: Improve naming of main_irq cause/mask identifiers
Ralf Baechle (1):
[MIPS] ATA: Rename routerboard 500 to 532
Sonic Zhang (1):
Fix bug - Implement bfin ata interrupt handler to avoid "irq 68 nobody cared" (v2)
Tejun Heo (2):
libata-scsi: clean up inquiry / mode sense related functions
libata-scsi: improve rbuf handling for simulated commands
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 292aa9a..1c11df9 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -566,11 +566,11 @@ config PATA_RADISYS
If unsure, say N.
-config PATA_RB500
- tristate "RouterBoard 500 PATA CompactFlash support"
- depends on MIKROTIK_RB500
+config PATA_RB532
+ tristate "RouterBoard 532 PATA CompactFlash support"
+ depends on MIKROTIK_RB532
help
- This option enables support for the RouterBoard 500
+ This option enables support for the RouterBoard 532
PATA CompactFlash controller.
If unsure, say N.
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 1fbc2aa..b693d82 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -55,7 +55,7 @@ obj-$(CONFIG_PATA_PDC2027X) += pata_pdc2027x.o
obj-$(CONFIG_PATA_PDC_OLD) += pata_pdc202xx_old.o
obj-$(CONFIG_PATA_QDI) += pata_qdi.o
obj-$(CONFIG_PATA_RADISYS) += pata_radisys.o
-obj-$(CONFIG_PATA_RB500) += pata_rb500_cf.o
+obj-$(CONFIG_PATA_RB532) += pata_rb532_cf.o
obj-$(CONFIG_PATA_RZ1000) += pata_rz1000.o
obj-$(CONFIG_PATA_SC1200) += pata_sc1200.o
obj-$(CONFIG_PATA_SERVERWORKS) += pata_serverworks.o
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index a34f324..3ce4392 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -49,7 +49,11 @@
#include "libata.h"
-#define SECTOR_SIZE 512
+#define SECTOR_SIZE 512
+#define ATA_SCSI_RBUF_SIZE 4096
+
+static DEFINE_SPINLOCK(ata_scsi_rbuf_lock);
+static u8 ata_scsi_rbuf[ATA_SCSI_RBUF_SIZE];
typedef unsigned int (*ata_xlat_func_t)(struct ata_queued_cmd *qc);
@@ -179,6 +183,13 @@ DEVICE_ATTR(link_power_management_policy, S_IRUGO | S_IWUSR,
ata_scsi_lpm_show, ata_scsi_lpm_put);
EXPORT_SYMBOL_GPL(dev_attr_link_power_management_policy);
+static void ata_scsi_set_sense(struct scsi_cmnd *cmd, u8 sk, u8 asc, u8 ascq)
+{
+ cmd->result = (DRIVER_SENSE << 24) | SAM_STAT_CHECK_CONDITION;
+
+ scsi_build_sense_buffer(0, cmd->sense_buffer, sk, asc, ascq);
+}
+
static void ata_scsi_invalid_field(struct scsi_cmnd *cmd,
void (*done)(struct scsi_cmnd *))
{
@@ -1632,53 +1643,48 @@ defer:
/**
* ata_scsi_rbuf_get - Map response buffer.
- * @cmd: SCSI command containing buffer to be mapped.
- * @buf_out: Pointer to mapped area.
+ * @flags: unsigned long variable to store irq enable status
+ * @copy_in: copy in from user buffer
*
- * Maps buffer contained within SCSI command @cmd.
+ * Prepare buffer for simulated SCSI commands.
*
* LOCKING:
- * spin_lock_irqsave(host lock)
+ * spin_lock_irqsave(ata_scsi_rbuf_lock) on success
*
* RETURNS:
- * Length of response buffer.
+ * Pointer to response buffer.
*/
-
-static unsigned int ata_scsi_rbuf_get(struct scsi_cmnd *cmd, u8 **buf_out)
+static void *ata_scsi_rbuf_get(struct scsi_cmnd *cmd, bool copy_in,
+ unsigned long *flags)
{
- u8 *buf;
- unsigned int buflen;
-
- struct scatterlist *sg = scsi_sglist(cmd);
+ spin_lock_irqsave(&ata_scsi_rbuf_lock, *flags);
- if (sg) {
- buf = kmap_atomic(sg_page(sg), KM_IRQ0) + sg->offset;
- buflen = sg->length;
- } else {
- buf = NULL;
- buflen = 0;
- }
-
- *buf_out = buf;
- return buflen;
+ memset(ata_scsi_rbuf, 0, ATA_SCSI_RBUF_SIZE);
+ if (copy_in)
+ sg_copy_to_buffer(scsi_sglist(cmd), scsi_sg_count(cmd),
+ ata_scsi_rbuf, ATA_SCSI_RBUF_SIZE);
+ return ata_scsi_rbuf;
}
/**
* ata_scsi_rbuf_put - Unmap response buffer.
* @cmd: SCSI command containing buffer to be unmapped.
- * @buf: buffer to unmap
+ * @copy_out: copy out result
+ * @flags: @flags passed to ata_scsi_rbuf_get()
*
- * Unmaps response buffer contained within @cmd.
+ * Returns rbuf buffer. The result is copied to @cmd's buffer if
+ * @copy_back is true.
*
* LOCKING:
- * spin_lock_irqsave(host lock)
+ * Unlocks ata_scsi_rbuf_lock.
*/
-
-static inline void ata_scsi_rbuf_put(struct scsi_cmnd *cmd, u8 *buf)
+static inline void ata_scsi_rbuf_put(struct scsi_cmnd *cmd, bool copy_out,
+ unsigned long *flags)
{
- struct scatterlist *sg = scsi_sglist(cmd);
- if (sg)
- kunmap_atomic(buf - sg->offset, KM_IRQ0);
+ if (copy_out)
+ sg_copy_from_buffer(scsi_sglist(cmd), scsi_sg_count(cmd),
+ ata_scsi_rbuf, ATA_SCSI_RBUF_SIZE);
+ spin_unlock_irqrestore(&ata_scsi_rbuf_lock, *flags);
}
/**
@@ -1696,24 +1702,17 @@ static inline void ata_scsi_rbuf_put(struct scsi_cmnd *cmd, u8 *buf)
* LOCKING:
* spin_lock_irqsave(host lock)
*/
-
-void ata_scsi_rbuf_fill(struct ata_scsi_args *args,
- unsigned int (*actor) (struct ata_scsi_args *args,
- u8 *rbuf, unsigned int buflen))
+static void ata_scsi_rbuf_fill(struct ata_scsi_args *args,
+ unsigned int (*actor)(struct ata_scsi_args *args, u8 *rbuf))
{
u8 *rbuf;
- unsigned int buflen, rc;
+ unsigned int rc;
struct scsi_cmnd *cmd = args->cmd;
unsigned long flags;
- local_irq_save(flags);
-
- buflen = ata_scsi_rbuf_get(cmd, &rbuf);
- memset(rbuf, 0, buflen);
- rc = actor(args, rbuf, buflen);
- ata_scsi_rbuf_put(cmd, rbuf);
-
- local_irq_restore(flags);
+ rbuf = ata_scsi_rbuf_get(cmd, false, &flags);
+ rc = actor(args, rbuf);
+ ata_scsi_rbuf_put(cmd, rc == 0, &flags);
if (rc == 0)
cmd->result = SAM_STAT_GOOD;
@@ -1721,26 +1720,9 @@ void ata_scsi_rbuf_fill(struct ata_scsi_args *args,
}
/**
- * ATA_SCSI_RBUF_SET - helper to set values in SCSI response buffer
- * @idx: byte index into SCSI response buffer
- * @val: value to set
- *
- * To be used by SCSI command simulator functions. This macros
- * expects two local variables, u8 *rbuf and unsigned int buflen,
- * are in scope.
- *
- * LOCKING:
- * None.
- */
-#define ATA_SCSI_RBUF_SET(idx, val) do { \
- if ((idx) < buflen) rbuf[(idx)] = (u8)(val); \
- } while (0)
-
-/**
* ata_scsiop_inq_std - Simulate INQUIRY command
* @args: device IDENTIFY data / SCSI command of interest.
* @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
- * @buflen: Response buffer length.
*
* Returns standard device identification data associated
* with non-VPD INQUIRY command output.
@@ -1748,10 +1730,17 @@ void ata_scsi_rbuf_fill(struct ata_scsi_args *args,
* LOCKING:
* spin_lock_irqsave(host lock)
*/
-
-unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen)
+static unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf)
{
+ const u8 versions[] = {
+ 0x60, /* SAM-3 (no version claimed) */
+
+ 0x03,
+ 0x20, /* SBC-2 (no version claimed) */
+
+ 0x02,
+ 0x60 /* SPC-3 (no version claimed) */
+ };
u8 hdr[] = {
TYPE_DISK,
0,
@@ -1760,35 +1749,21 @@ unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf,
95 - 4
};
+ VPRINTK("ENTER\n");
+
/* set scsi removeable (RMB) bit per ata bit */
if (ata_id_removeable(args->id))
hdr[1] |= (1 << 7);
- VPRINTK("ENTER\n");
-
memcpy(rbuf, hdr, sizeof(hdr));
+ memcpy(&rbuf[8], "ATA ", 8);
+ ata_id_string(args->id, &rbuf[16], ATA_ID_PROD, 16);
+ ata_id_string(args->id, &rbuf[32], ATA_ID_FW_REV, 4);
- if (buflen > 35) {
- memcpy(&rbuf[8], "ATA ", 8);
- ata_id_string(args->id, &rbuf[16], ATA_ID_PROD, 16);
- ata_id_string(args->id, &rbuf[32], ATA_ID_FW_REV, 4);
- if (rbuf[32] == 0 || rbuf[32] == ' ')
- memcpy(&rbuf[32], "n/a ", 4);
- }
-
- if (buflen > 63) {
- const u8 versions[] = {
- 0x60, /* SAM-3 (no version claimed) */
-
- 0x03,
- 0x20, /* SBC-2 (no version claimed) */
+ if (rbuf[32] == 0 || rbuf[32] == ' ')
+ memcpy(&rbuf[32], "n/a ", 4);
- 0x02,
- 0x60 /* SPC-3 (no version claimed) */
- };
-
- memcpy(rbuf + 59, versions, sizeof(versions));
- }
+ memcpy(rbuf + 59, versions, sizeof(versions));
return 0;
}
@@ -1797,27 +1772,22 @@ unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf,
* ata_scsiop_inq_00 - Simulate INQUIRY VPD page 0, list of pages
* @args: device IDENTIFY data / SCSI command of interest.
* @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
- * @buflen: Response buffer length.
*
* Returns list of inquiry VPD pages available.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*/
-
-unsigned int ata_scsiop_inq_00(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen)
+static unsigned int ata_scsiop_inq_00(struct ata_scsi_args *args, u8 *rbuf)
{
const u8 pages[] = {
0x00, /* page 0x00, this page */
0x80, /* page 0x80, unit serial no page */
0x83 /* page 0x83, device ident page */
};
- rbuf[3] = sizeof(pages); /* number of supported VPD pages */
-
- if (buflen > 6)
- memcpy(rbuf + 4, pages, sizeof(pages));
+ rbuf[3] = sizeof(pages); /* number of supported VPD pages */
+ memcpy(rbuf + 4, pages, sizeof(pages));
return 0;
}
@@ -1825,16 +1795,13 @@ unsigned int ata_scsiop_inq_00(struct ata_scsi_args *args, u8 *rbuf,
* ata_scsiop_inq_80 - Simulate INQUIRY VPD page 80, device serial number
* @args: device IDENTIFY data / SCSI command of interest.
* @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
- * @buflen: Response buffer length.
*
* Returns ATA device serial number.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*/
-
-unsigned int ata_scsiop_inq_80(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen)
+static unsigned int ata_scsiop_inq_80(struct ata_scsi_args *args, u8 *rbuf)
{
const u8 hdr[] = {
0,
@@ -1842,12 +1809,10 @@ unsigned int ata_scsiop_inq_80(struct ata_scsi_args *args, u8 *rbuf,
0,
ATA_ID_SERNO_LEN, /* page len */
};
- memcpy(rbuf, hdr, sizeof(hdr));
-
- if (buflen > (ATA_ID_SERNO_LEN + 4 - 1))
- ata_id_string(args->id, (unsigned char *) &rbuf[4],
- ATA_ID_SERNO, ATA_ID_SERNO_LEN);
+ memcpy(rbuf, hdr, sizeof(hdr));
+ ata_id_string(args->id, (unsigned char *) &rbuf[4],
+ ATA_ID_SERNO, ATA_ID_SERNO_LEN);
return 0;
}
@@ -1855,7 +1820,6 @@ unsigned int ata_scsiop_inq_80(struct ata_scsi_args *args, u8 *rbuf,
* ata_scsiop_inq_83 - Simulate INQUIRY VPD page 83, device identity
* @args: device IDENTIFY data / SCSI command of interest.
* @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
- * @buflen: Response buffer length.
*
* Yields two logical unit device identification designators:
* - vendor specific ASCII containing the ATA serial number
@@ -1865,41 +1829,37 @@ unsigned int ata_scsiop_inq_80(struct ata_scsi_args *args, u8 *rbuf,
* LOCKING:
* spin_lock_irqsave(host lock)
*/
-
-unsigned int ata_scsiop_inq_83(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen)
+static unsigned int ata_scsiop_inq_83(struct ata_scsi_args *args, u8 *rbuf)
{
- int num;
const int sat_model_serial_desc_len = 68;
+ int num;
rbuf[1] = 0x83; /* this page code */
num = 4;
- if (buflen > (ATA_ID_SERNO_LEN + num + 3)) {
- /* piv=0, assoc=lu, code_set=ACSII, designator=vendor */
- rbuf[num + 0] = 2;
- rbuf[num + 3] = ATA_ID_SERNO_LEN;
- num += 4;
- ata_id_string(args->id, (unsigned char *) rbuf + num,
- ATA_ID_SERNO, ATA_ID_SERNO_LEN);
- num += ATA_ID_SERNO_LEN;
- }
- if (buflen > (sat_model_serial_desc_len + num + 3)) {
- /* SAT defined lu model and serial numbers descriptor */
- /* piv=0, assoc=lu, code_set=ACSII, designator=t10 vendor id */
- rbuf[num + 0] = 2;
- rbuf[num + 1] = 1;
- rbuf[num + 3] = sat_model_serial_desc_len;
- num += 4;
- memcpy(rbuf + num, "ATA ", 8);
- num += 8;
- ata_id_string(args->id, (unsigned char *) rbuf + num,
- ATA_ID_PROD, ATA_ID_PROD_LEN);
- num += ATA_ID_PROD_LEN;
- ata_id_string(args->id, (unsigned char *) rbuf + num,
- ATA_ID_SERNO, ATA_ID_SERNO_LEN);
- num += ATA_ID_SERNO_LEN;
- }
+ /* piv=0, assoc=lu, code_set=ACSII, designator=vendor */
+ rbuf[num + 0] = 2;
+ rbuf[num + 3] = ATA_ID_SERNO_LEN;
+ num += 4;
+ ata_id_string(args->id, (unsigned char *) rbuf + num,
+ ATA_ID_SERNO, ATA_ID_SERNO_LEN);
+ num += ATA_ID_SERNO_LEN;
+
+ /* SAT defined lu model and serial numbers descriptor */
+ /* piv=0, assoc=lu, code_set=ACSII, designator=t10 vendor id */
+ rbuf[num + 0] = 2;
+ rbuf[num + 1] = 1;
+ rbuf[num + 3] = sat_model_serial_desc_len;
+ num += 4;
+ memcpy(rbuf + num, "ATA ", 8);
+ num += 8;
+ ata_id_string(args->id, (unsigned char *) rbuf + num, ATA_ID_PROD,
+ ATA_ID_PROD_LEN);
+ num += ATA_ID_PROD_LEN;
+ ata_id_string(args->id, (unsigned char *) rbuf + num, ATA_ID_SERNO,
+ ATA_ID_SERNO_LEN);
+ num += ATA_ID_SERNO_LEN;
+
rbuf[3] = num - 4; /* page len (assume less than 256 bytes) */
return 0;
}
@@ -1908,35 +1868,26 @@ unsigned int ata_scsiop_inq_83(struct ata_scsi_args *args, u8 *rbuf,
* ata_scsiop_inq_89 - Simulate INQUIRY VPD page 89, ATA info
* @args: device IDENTIFY data / SCSI command of interest.
* @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
- * @buflen: Response buffer length.
*
* Yields SAT-specified ATA VPD page.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*/
-
-static unsigned int ata_scsiop_inq_89(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen)
+static unsigned int ata_scsiop_inq_89(struct ata_scsi_args *args, u8 *rbuf)
{
- u8 pbuf[60];
struct ata_taskfile tf;
- unsigned int i;
- if (!buflen)
- return 0;
-
- memset(&pbuf, 0, sizeof(pbuf));
memset(&tf, 0, sizeof(tf));
- pbuf[1] = 0x89; /* our page code */
- pbuf[2] = (0x238 >> 8); /* page size fixed at 238h */
- pbuf[3] = (0x238 & 0xff);
+ rbuf[1] = 0x89; /* our page code */
+ rbuf[2] = (0x238 >> 8); /* page size fixed at 238h */
+ rbuf[3] = (0x238 & 0xff);
- memcpy(&pbuf[8], "linux ", 8);
- memcpy(&pbuf[16], "libata ", 16);
- memcpy(&pbuf[32], DRV_VERSION, 4);
- ata_id_string(args->id, &pbuf[32], ATA_ID_FW_REV, 4);
+ memcpy(&rbuf[8], "linux ", 8);
+ memcpy(&rbuf[16], "libata ", 16);
+ memcpy(&rbuf[32], DRV_VERSION, 4);
+ ata_id_string(args->id, &rbuf[32], ATA_ID_FW_REV, 4);
/* we don't store the ATA device signature, so we fake it */
@@ -1944,19 +1895,12 @@ static unsigned int ata_scsiop_inq_89(struct ata_scsi_args *args, u8 *rbuf,
tf.lbal = 0x1;
tf.nsect = 0x1;
- ata_tf_to_fis(&tf, 0, 1, &pbuf[36]); /* TODO: PMP? */
- pbuf[36] = 0x34; /* force D2H Reg FIS (34h) */
+ ata_tf_to_fis(&tf, 0, 1, &rbuf[36]); /* TODO: PMP? */
+ rbuf[36] = 0x34; /* force D2H Reg FIS (34h) */
- pbuf[56] = ATA_CMD_ID_ATA;
+ rbuf[56] = ATA_CMD_ID_ATA;
- i = min(buflen, 60U);
- memcpy(rbuf, &pbuf[0], i);
- buflen -= i;
-
- if (!buflen)
- return 0;
-
- memcpy(&rbuf[60], &args->id[0], min(buflen, 512U));
+ memcpy(&rbuf[60], &args->id[0], 512);
return 0;
}
@@ -1964,7 +1908,6 @@ static unsigned int ata_scsiop_inq_89(struct ata_scsi_args *args, u8 *rbuf,
* ata_scsiop_noop - Command handler that simply returns success.
* @args: device IDENTIFY data / SCSI command of interest.
* @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
- * @buflen: Response buffer length.
*
* No operation. Simply returns success to caller, to indicate
* that the caller should successfully complete this SCSI command.
@@ -1972,47 +1915,16 @@ static unsigned int ata_scsiop_inq_89(struct ata_scsi_args *args, u8 *rbuf,
* LOCKING:
* spin_lock_irqsave(host lock)
*/
-
-unsigned int ata_scsiop_noop(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen)
+static unsigned int ata_scsiop_noop(struct ata_scsi_args *args, u8 *rbuf)
{
VPRINTK("ENTER\n");
return 0;
}
/**
- * ata_msense_push - Push data onto MODE SENSE data output buffer
- * @ptr_io: (input/output) Location to store more output data
- * @last: End of output data buffer
- * @buf: Pointer to BLOB being added to output buffer
- * @buflen: Length of BLOB
- *
- * Store MODE SENSE data on an output buffer.
- *
- * LOCKING:
- * None.
- */
-
-static void ata_msense_push(u8 **ptr_io, const u8 *last,
- const u8 *buf, unsigned int buflen)
-{
- u8 *ptr = *ptr_io;
-
- if ((ptr + buflen - 1) > last)
- return;
-
- memcpy(ptr, buf, buflen);
-
- ptr += buflen;
-
- *ptr_io = ptr;
-}
-
-/**
* ata_msense_caching - Simulate MODE SENSE caching info page
* @id: device IDENTIFY data
- * @ptr_io: (input/output) Location to store more output data
- * @last: End of output data buffer
+ * @buf: output buffer
*
* Generate a caching info page, which conditionally indicates
* write caching to the SCSI layer, depending on device
@@ -2021,58 +1933,43 @@ static void ata_msense_push(u8 **ptr_io, const u8 *last,
* LOCKING:
* None.
*/
-
-static unsigned int ata_msense_caching(u16 *id, u8 **ptr_io,
- const u8 *last)
+static unsigned int ata_msense_caching(u16 *id, u8 *buf)
{
- u8 page[CACHE_MPAGE_LEN];
-
- memcpy(page, def_cache_mpage, sizeof(page));
+ memcpy(buf, def_cache_mpage, sizeof(def_cache_mpage));
if (ata_id_wcache_enabled(id))
- page[2] |= (1 << 2); /* write cache enable */
+ buf[2] |= (1 << 2); /* write cache enable */
if (!ata_id_rahead_enabled(id))
- page[12] |= (1 << 5); /* disable read ahead */
-
- ata_msense_push(ptr_io, last, page, sizeof(page));
- return sizeof(page);
+ buf[12] |= (1 << 5); /* disable read ahead */
+ return sizeof(def_cache_mpage);
}
/**
* ata_msense_ctl_mode - Simulate MODE SENSE control mode page
- * @dev: Device associated with this MODE SENSE command
- * @ptr_io: (input/output) Location to store more output data
- * @last: End of output data buffer
+ * @buf: output buffer
*
* Generate a generic MODE SENSE control mode page.
*
* LOCKING:
* None.
*/
-
-static unsigned int ata_msense_ctl_mode(u8 **ptr_io, const u8 *last)
+static unsigned int ata_msense_ctl_mode(u8 *buf)
{
- ata_msense_push(ptr_io, last, def_control_mpage,
- sizeof(def_control_mpage));
+ memcpy(buf, def_control_mpage, sizeof(def_control_mpage));
return sizeof(def_control_mpage);
}
/**
* ata_msense_rw_recovery - Simulate MODE SENSE r/w error recovery page
- * @dev: Device associated with this MODE SENSE command
- * @ptr_io: (input/output) Location to store more output data
- * @last: End of output data buffer
+ * @bufp: output buffer
*
* Generate a generic MODE SENSE r/w error recovery page.
*
* LOCKING:
* None.
*/
-
-static unsigned int ata_msense_rw_recovery(u8 **ptr_io, const u8 *last)
+static unsigned int ata_msense_rw_recovery(u8 *buf)
{
-
- ata_msense_push(ptr_io, last, def_rw_recovery_mpage,
- sizeof(def_rw_recovery_mpage));
+ memcpy(buf, def_rw_recovery_mpage, sizeof(def_rw_recovery_mpage));
return sizeof(def_rw_recovery_mpage);
}
@@ -2104,7 +2001,6 @@ static int ata_dev_supports_fua(u16 *id)
* ata_scsiop_mode_sense - Simulate MODE SENSE 6, 10 commands
* @args: device IDENTIFY data / SCSI command of interest.
* @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
- * @buflen: Response buffer length.
*
* Simulate MODE SENSE commands. Assume this is invoked for direct
* access devices (e.g. disks) only. There should be no block
@@ -2113,19 +2009,17 @@ static int ata_dev_supports_fua(u16 *id)
* LOCKING:
* spin_lock_irqsave(host lock)
*/
-
-unsigned int ata_scsiop_mode_sense(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen)
+static unsigned int ata_scsiop_mode_sense(struct ata_scsi_args *args, u8 *rbuf)
{
struct ata_device *dev = args->dev;
- u8 *scsicmd = args->cmd->cmnd, *p, *last;
+ u8 *scsicmd = args->cmd->cmnd, *p = rbuf;
const u8 sat_blk_desc[] = {
0, 0, 0, 0, /* number of blocks: sat unspecified */
0,
0, 0x2, 0x0 /* block length: 512 bytes */
};
u8 pg, spg;
- unsigned int ebd, page_control, six_byte, output_len, alloc_len, minlen;
+ unsigned int ebd, page_control, six_byte;
u8 dpofua;
VPRINTK("ENTER\n");
@@ -2148,17 +2042,10 @@ unsigned int ata_scsiop_mode_sense(struct ata_scsi_args *args, u8 *rbuf,
goto invalid_fld;
}
- if (six_byte) {
- output_len = 4 + (ebd ? 8 : 0);
- alloc_len = scsicmd[4];
- } else {
- output_len = 8 + (ebd ? 8 : 0);
- alloc_len = (scsicmd[7] << 8) + scsicmd[8];
- }
- minlen = (alloc_len < buflen) ? alloc_len : buflen;
-
- p = rbuf + output_len;
- last = rbuf + minlen - 1;
+ if (six_byte)
+ p += 4 + (ebd ? 8 : 0);
+ else
+ p += 8 + (ebd ? 8 : 0);
pg = scsicmd[2] & 0x3f;
spg = scsicmd[3];
@@ -2171,61 +2058,48 @@ unsigned int ata_scsiop_mode_sense(struct ata_scsi_args *args, u8 *rbuf,
switch(pg) {
case RW_RECOVERY_MPAGE:
- output_len += ata_msense_rw_recovery(&p, last);
+ p += ata_msense_rw_recovery(p);
break;
case CACHE_MPAGE:
- output_len += ata_msense_caching(args->id, &p, last);
+ p += ata_msense_caching(args->id, p);
break;
- case CONTROL_MPAGE: {
- output_len += ata_msense_ctl_mode(&p, last);
+ case CONTROL_MPAGE:
+ p += ata_msense_ctl_mode(p);
break;
- }
case ALL_MPAGES:
- output_len += ata_msense_rw_recovery(&p, last);
- output_len += ata_msense_caching(args->id, &p, last);
- output_len += ata_msense_ctl_mode(&p, last);
+ p += ata_msense_rw_recovery(p);
+ p += ata_msense_caching(args->id, p);
+ p += ata_msense_ctl_mode(p);
break;
default: /* invalid page code */
goto invalid_fld;
}
- if (minlen < 1)
- return 0;
-
dpofua = 0;
if (ata_dev_supports_fua(args->id) && (dev->flags & ATA_DFLAG_LBA48) &&
(!(dev->flags & ATA_DFLAG_PIO) || dev->multi_count))
dpofua = 1 << 4;
if (six_byte) {
- output_len--;
- rbuf[0] = output_len;
- if (minlen > 2)
- rbuf[2] |= dpofua;
+ rbuf[0] = p - rbuf - 1;
+ rbuf[2] |= dpofua;
if (ebd) {
- if (minlen > 3)
- rbuf[3] = sizeof(sat_blk_desc);
- if (minlen > 11)
- memcpy(rbuf + 4, sat_blk_desc,
- sizeof(sat_blk_desc));
+ rbuf[3] = sizeof(sat_blk_desc);
+ memcpy(rbuf + 4, sat_blk_desc, sizeof(sat_blk_desc));
}
} else {
- output_len -= 2;
+ unsigned int output_len = p - rbuf - 2;
+
rbuf[0] = output_len >> 8;
- if (minlen > 1)
- rbuf[1] = output_len;
- if (minlen > 3)
- rbuf[3] |= dpofua;
+ rbuf[1] = output_len;
+ rbuf[3] |= dpofua;
if (ebd) {
- if (minlen > 7)
- rbuf[7] = sizeof(sat_blk_desc);
- if (minlen > 15)
- memcpy(rbuf + 8, sat_blk_desc,
- sizeof(sat_blk_desc));
+ rbuf[7] = sizeof(sat_blk_desc);
+ memcpy(rbuf + 8, sat_blk_desc, sizeof(sat_blk_desc));
}
}
return 0;
@@ -2245,15 +2119,13 @@ saving_not_supp:
* ata_scsiop_read_cap - Simulate READ CAPACITY[ 16] commands
* @args: device IDENTIFY data / SCSI command of interest.
* @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
- * @buflen: Response buffer length.
*
* Simulate READ CAPACITY commands.
*
* LOCKING:
* None.
*/
-unsigned int ata_scsiop_read_cap(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen)
+static unsigned int ata_scsiop_read_cap(struct ata_scsi_args *args, u8 *rbuf)
{
u64 last_lba = args->dev->n_sectors - 1; /* LBA of the last block */
@@ -2264,28 +2136,28 @@ unsigned int ata_scsiop_read_cap(struct ata_scsi_args *args, u8 *rbuf,
last_lba = 0xffffffff;
/* sector count, 32-bit */
- ATA_SCSI_RBUF_SET(0, last_lba >> (8 * 3));
- ATA_SCSI_RBUF_SET(1, last_lba >> (8 * 2));
- ATA_SCSI_RBUF_SET(2, last_lba >> (8 * 1));
- ATA_SCSI_RBUF_SET(3, last_lba);
+ rbuf[0] = last_lba >> (8 * 3);
+ rbuf[1] = last_lba >> (8 * 2);
+ rbuf[2] = last_lba >> (8 * 1);
+ rbuf[3] = last_lba;
/* sector size */
- ATA_SCSI_RBUF_SET(6, ATA_SECT_SIZE >> 8);
- ATA_SCSI_RBUF_SET(7, ATA_SECT_SIZE & 0xff);
+ rbuf[6] = ATA_SECT_SIZE >> 8;
+ rbuf[7] = ATA_SECT_SIZE & 0xff;
} else {
/* sector count, 64-bit */
- ATA_SCSI_RBUF_SET(0, last_lba >> (8 * 7));
- ATA_SCSI_RBUF_SET(1, last_lba >> (8 * 6));
- ATA_SCSI_RBUF_SET(2, last_lba >> (8 * 5));
- ATA_SCSI_RBUF_SET(3, last_lba >> (8 * 4));
- ATA_SCSI_RBUF_SET(4, last_lba >> (8 * 3));
- ATA_SCSI_RBUF_SET(5, last_lba >> (8 * 2));
- ATA_SCSI_RBUF_SET(6, last_lba >> (8 * 1));
- ATA_SCSI_RBUF_SET(7, last_lba);
+ rbuf[0] = last_lba >> (8 * 7);
+ rbuf[1] = last_lba >> (8 * 6);
+ rbuf[2] = last_lba >> (8 * 5);
+ rbuf[3] = last_lba >> (8 * 4);
+ rbuf[4] = last_lba >> (8 * 3);
+ rbuf[5] = last_lba >> (8 * 2);
+ rbuf[6] = last_lba >> (8 * 1);
+ rbuf[7] = last_lba;
/* sector size */
- ATA_SCSI_RBUF_SET(10, ATA_SECT_SIZE >> 8);
- ATA_SCSI_RBUF_SET(11, ATA_SECT_SIZE & 0xff);
+ rbuf[10] = ATA_SECT_SIZE >> 8;
+ rbuf[11] = ATA_SECT_SIZE & 0xff;
}
return 0;
@@ -2295,16 +2167,13 @@ unsigned int ata_scsiop_read_cap(struct ata_scsi_args *args, u8 *rbuf,
* ata_scsiop_report_luns - Simulate REPORT LUNS command
* @args: device IDENTIFY data / SCSI command of interest.
* @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
- * @buflen: Response buffer length.
*
* Simulate REPORT LUNS command.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*/
-
-unsigned int ata_scsiop_report_luns(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen)
+static unsigned int ata_scsiop_report_luns(struct ata_scsi_args *args, u8 *rbuf)
{
VPRINTK("ENTER\n");
rbuf[3] = 8; /* just one lun, LUN 0, size 8 bytes */
@@ -2312,53 +2181,6 @@ unsigned int ata_scsiop_report_luns(struct ata_scsi_args *args, u8 *rbuf,
return 0;
}
-/**
- * ata_scsi_set_sense - Set SCSI sense data and status
- * @cmd: SCSI request to be handled
- * @sk: SCSI-defined sense key
- * @asc: SCSI-defined additional sense code
- * @ascq: SCSI-defined additional sense code qualifier
- *
- * Helper function that builds a valid fixed format, current
- * response code and the given sense key (sk), additional sense
- * code (asc) and additional sense code qualifier (ascq) with
- * a SCSI command status of %SAM_STAT_CHECK_CONDITION and
- * DRIVER_SENSE set in the upper bits of scsi_cmnd::result .
- *
- * LOCKING:
- * Not required
- */
-
-void ata_scsi_set_sense(struct scsi_cmnd *cmd, u8 sk, u8 asc, u8 ascq)
-{
- cmd->result = (DRIVER_SENSE << 24) | SAM_STAT_CHECK_CONDITION;
-
- scsi_build_sense_buffer(0, cmd->sense_buffer, sk, asc, ascq);
-}
-
-/**
- * ata_scsi_badcmd - End a SCSI request with an error
- * @cmd: SCSI request to be handled
- * @done: SCSI command completion function
- * @asc: SCSI-defined additional sense code
- * @ascq: SCSI-defined additional sense code qualifier
- *
- * Helper function that completes a SCSI command with
- * %SAM_STAT_CHECK_CONDITION, with a sense key %ILLEGAL_REQUEST
- * and the specified additional sense codes.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- */
-
-void ata_scsi_badcmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *), u8 asc, u8 ascq)
-{
- DPRINTK("ENTER\n");
- ata_scsi_set_sense(cmd, ILLEGAL_REQUEST, asc, ascq);
-
- done(cmd);
-}
-
static void atapi_sense_complete(struct ata_queued_cmd *qc)
{
if (qc->err_mask && ((qc->err_mask & AC_ERR_DEV) == 0)) {
@@ -2485,13 +2307,10 @@ static void atapi_qc_complete(struct ata_queued_cmd *qc)
u8 *scsicmd = cmd->cmnd;
if ((scsicmd[0] == INQUIRY) && ((scsicmd[1] & 0x03) == 0)) {
- u8 *buf = NULL;
- unsigned int buflen;
unsigned long flags;
+ u8 *buf;
- local_irq_save(flags);
-
- buflen = ata_scsi_rbuf_get(cmd, &buf);
+ buf = ata_scsi_rbuf_get(cmd, true, &flags);
/* ATAPI devices typically report zero for their SCSI version,
* and sometimes deviate from the spec WRT response data
@@ -2506,9 +2325,7 @@ static void atapi_qc_complete(struct ata_queued_cmd *qc)
buf[3] = 0x32;
}
- ata_scsi_rbuf_put(cmd, buf);
-
- local_irq_restore(flags);
+ ata_scsi_rbuf_put(cmd, true, &flags);
}
cmd->result = SAM_STAT_GOOD;
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index ae2cfd9..4514283 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -146,34 +146,6 @@ extern void ata_scsi_scan_host(struct ata_port *ap, int sync);
extern int ata_scsi_offline_dev(struct ata_device *dev);
extern void ata_scsi_media_change_notify(struct ata_device *dev);
extern void ata_scsi_hotplug(struct work_struct *work);
-extern unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen);
-
-extern unsigned int ata_scsiop_inq_00(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen);
-
-extern unsigned int ata_scsiop_inq_80(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen);
-extern unsigned int ata_scsiop_inq_83(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen);
-extern unsigned int ata_scsiop_noop(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen);
-extern unsigned int ata_scsiop_sync_cache(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen);
-extern unsigned int ata_scsiop_mode_sense(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen);
-extern unsigned int ata_scsiop_read_cap(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen);
-extern unsigned int ata_scsiop_report_luns(struct ata_scsi_args *args, u8 *rbuf,
- unsigned int buflen);
-extern void ata_scsi_badcmd(struct scsi_cmnd *cmd,
- void (*done)(struct scsi_cmnd *),
- u8 asc, u8 ascq);
-extern void ata_scsi_set_sense(struct scsi_cmnd *cmd,
- u8 sk, u8 asc, u8 ascq);
-extern void ata_scsi_rbuf_fill(struct ata_scsi_args *args,
- unsigned int (*actor) (struct ata_scsi_args *args,
- u8 *rbuf, unsigned int buflen));
extern void ata_schedule_scsi_eh(struct Scsi_Host *shost);
extern void ata_scsi_dev_rescan(struct work_struct *work);
extern int ata_bus_probe(struct ata_port *ap);
diff --git a/drivers/ata/pata_bf54x.c b/drivers/ata/pata_bf54x.c
index a75de06..9ab8973 100644
--- a/drivers/ata/pata_bf54x.c
+++ b/drivers/ata/pata_bf54x.c
@@ -1272,8 +1272,8 @@ static void bfin_freeze(struct ata_port *ap)
void bfin_thaw(struct ata_port *ap)
{
+ dev_dbg(ap->dev, "in atapi dma thaw\n");
bfin_check_status(ap);
- bfin_irq_clear(ap);
bfin_irq_on(ap);
}
@@ -1339,13 +1339,130 @@ static int bfin_port_start(struct ata_port *ap)
return 0;
}
+static unsigned int bfin_ata_host_intr(struct ata_port *ap,
+ struct ata_queued_cmd *qc)
+{
+ struct ata_eh_info *ehi = &ap->link.eh_info;
+ u8 status, host_stat = 0;
+
+ VPRINTK("ata%u: protocol %d task_state %d\n",
+ ap->print_id, qc->tf.protocol, ap->hsm_task_state);
+
+ /* Check whether we are expecting interrupt in this state */
+ switch (ap->hsm_task_state) {
+ case HSM_ST_FIRST:
+ /* Some pre-ATAPI-4 devices assert INTRQ
+ * at this state when ready to receive CDB.
+ */
+
+ /* Check the ATA_DFLAG_CDB_INTR flag is enough here.
+ * The flag was turned on only for atapi devices.
+ * No need to check is_atapi_taskfile(&qc->tf) again.
+ */
+ if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
+ goto idle_irq;
+ break;
+ case HSM_ST_LAST:
+ if (qc->tf.protocol == ATA_PROT_DMA ||
+ qc->tf.protocol == ATAPI_PROT_DMA) {
+ /* check status of DMA engine */
+ host_stat = ap->ops->bmdma_status(ap);
+ VPRINTK("ata%u: host_stat 0x%X\n",
+ ap->print_id, host_stat);
+
+ /* if it's not our irq... */
+ if (!(host_stat & ATA_DMA_INTR))
+ goto idle_irq;
+
+ /* before we do anything else, clear DMA-Start bit */
+ ap->ops->bmdma_stop(qc);
+
+ if (unlikely(host_stat & ATA_DMA_ERR)) {
+ /* error when transfering data to/from memory */
+ qc->err_mask |= AC_ERR_HOST_BUS;
+ ap->hsm_task_state = HSM_ST_ERR;
+ }
+ }
+ break;
+ case HSM_ST:
+ break;
+ default:
+ goto idle_irq;
+ }
+
+ /* check altstatus */
+ status = ap->ops->sff_check_altstatus(ap);
+ if (status & ATA_BUSY)
+ goto busy_ata;
+
+ /* check main status, clearing INTRQ */
+ status = ap->ops->sff_check_status(ap);
+ if (unlikely(status & ATA_BUSY))
+ goto busy_ata;
+
+ /* ack bmdma irq events */
+ ap->ops->sff_irq_clear(ap);
+
+ ata_sff_hsm_move(ap, qc, status, 0);
+
+ if (unlikely(qc->err_mask) && (qc->tf.protocol == ATA_PROT_DMA ||
+ qc->tf.protocol == ATAPI_PROT_DMA))
+ ata_ehi_push_desc(ehi, "BMDMA stat 0x%x", host_stat);
+
+busy_ata:
+ return 1; /* irq handled */
+
+idle_irq:
+ ap->stats.idle_irq++;
+
+#ifdef ATA_IRQ_TRAP
+ if ((ap->stats.idle_irq % 1000) == 0) {
+ ap->ops->irq_ack(ap, 0); /* debug trap */
+ ata_port_printk(ap, KERN_WARNING, "irq trap\n");
+ return 1;
+ }
+#endif
+ return 0; /* irq not handled */
+}
+
+static irqreturn_t bfin_ata_interrupt(int irq, void *dev_instance)
+{
+ struct ata_host *host = dev_instance;
+ unsigned int i;
+ unsigned int handled = 0;
+ unsigned long flags;
+
+ /* TODO: make _irqsave conditional on x86 PCI IDE legacy mode */
+ spin_lock_irqsave(&host->lock, flags);
+
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap;
+
+ ap = host->ports[i];
+ if (ap &&
+ !(ap->flags & ATA_FLAG_DISABLED)) {
+ struct ata_queued_cmd *qc;
+
+ qc = ata_qc_from_tag(ap, ap->link.active_tag);
+ if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING)) &&
+ (qc->flags & ATA_QCFLAG_ACTIVE))
+ handled |= bfin_ata_host_intr(ap, qc);
+ }
+ }
+
+ spin_unlock_irqrestore(&host->lock, flags);
+
+ return IRQ_RETVAL(handled);
+}
+
+
static struct scsi_host_template bfin_sht = {
ATA_BASE_SHT(DRV_NAME),
.sg_tablesize = SG_NONE,
.dma_boundary = ATA_DMA_BOUNDARY,
};
-static const struct ata_port_operations bfin_pata_ops = {
+static struct ata_port_operations bfin_pata_ops = {
.inherits = &ata_sff_port_ops,
.set_piomode = bfin_set_piomode,
@@ -1370,7 +1487,6 @@ static const struct ata_port_operations bfin_pata_ops = {
.thaw = bfin_thaw,
.softreset = bfin_softreset,
.postreset = bfin_postreset,
- .post_internal_cmd = bfin_bmdma_stop,
.sff_irq_clear = bfin_irq_clear,
.sff_irq_on = bfin_irq_on,
@@ -1507,7 +1623,7 @@ static int __devinit bfin_atapi_probe(struct platform_device *pdev)
}
if (ata_host_activate(host, platform_get_irq(pdev, 0),
- ata_sff_interrupt, IRQF_SHARED, &bfin_sht) != 0) {
+ bfin_ata_interrupt, IRQF_SHARED, &bfin_sht) != 0) {
peripheral_free_list(atapi_io_port);
dev_err(&pdev->dev, "Fail to attach ATAPI device\n");
return -ENODEV;
diff --git a/drivers/ata/pata_rb500_cf.c b/drivers/ata/pata_rb500_cf.c
deleted file mode 100644
index 4345174..0000000
--- a/drivers/ata/pata_rb500_cf.c
+++ /dev/null
@@ -1,277 +0,0 @@
-/*
- * A low-level PATA driver to handle a Compact Flash connected on the
- * Mikrotik's RouterBoard 532 board.
- *
- * Copyright (C) 2007 Gabor Juhos <juhosg at openwrt.org>
- * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
- *
- * This file was based on: drivers/ata/pata_ixp4xx_cf.c
- * Copyright (C) 2006-07 Tower Technologies
- * Author: Alessandro Zummo <a.zummo@towertech.it>
- *
- * Also was based on the driver for Linux 2.4.xx published by Mikrotik for
- * their RouterBoard 1xx and 5xx series devices. The original Mikrotik code
- * seems not to have a license.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-
-#include <linux/io.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-
-#include <linux/libata.h>
-#include <scsi/scsi_host.h>
-
-#include <asm/gpio.h>
-
-#define DRV_NAME "pata-rb500-cf"
-#define DRV_VERSION "0.1.0"
-#define DRV_DESC "PATA driver for RouterBOARD 532 Compact Flash"
-
-#define RB500_CF_MAXPORTS 1
-#define RB500_CF_IO_DELAY 400
-
-#define RB500_CF_REG_CMD 0x0800
-#define RB500_CF_REG_CTRL 0x080E
-#define RB500_CF_REG_DATA 0x0C00
-
-struct rb500_cf_info {
- void __iomem *iobase;
- unsigned int gpio_line;
- int frozen;
- unsigned int irq;
-};
-
-/* ------------------------------------------------------------------------ */
-
-static inline void rb500_pata_finish_io(struct ata_port *ap)
-{
- struct ata_host *ah = ap->host;
- struct rb500_cf_info *info = ah->private_data;
-
- ata_sff_altstatus(ap);
- ndelay(RB500_CF_IO_DELAY);
-
- set_irq_type(info->irq, IRQ_TYPE_LEVEL_HIGH);
-}
-
-static void rb500_pata_exec_command(struct ata_port *ap,
- const struct ata_taskfile *tf)
-{
- writeb(tf->command, ap->ioaddr.command_addr);
- rb500_pata_finish_io(ap);
-}
-
-static void rb500_pata_data_xfer(struct ata_device *adev, unsigned char *buf,
- unsigned int buflen, int write_data)
-{
- struct ata_port *ap = adev->link->ap;
- void __iomem *ioaddr = ap->ioaddr.data_addr;
-
- if (write_data) {
- for (; buflen > 0; buflen--, buf++)
- writeb(*buf, ioaddr);
- } else {
- for (; buflen > 0; buflen--, buf++)
- *buf = readb(ioaddr);
- }
-
- rb500_pata_finish_io(adev->link->ap);
-}
-
-static void rb500_pata_freeze(struct ata_port *ap)
-{
- struct rb500_cf_info *info = ap->host->private_data;
-
- info->frozen = 1;
-}
-
-static void rb500_pata_thaw(struct ata_port *ap)
-{
- struct rb500_cf_info *info = ap->host->private_data;
-
- info->frozen = 0;
-}
-
-static irqreturn_t rb500_pata_irq_handler(int irq, void *dev_instance)
-{
- struct ata_host *ah = dev_instance;
- struct rb500_cf_info *info = ah->private_data;
-
- if (gpio_get_value(info->gpio_line)) {
- set_irq_type(info->irq, IRQ_TYPE_LEVEL_LOW);
- if (!info->frozen)
- ata_sff_interrupt(info->irq, dev_instance);
- } else {
- set_irq_type(info->irq, IRQ_TYPE_LEVEL_HIGH);
- }
-
- return IRQ_HANDLED;
-}
-
-static struct ata_port_operations rb500_pata_port_ops = {
- .inherits = &ata_sff_port_ops,
- .sff_exec_command = rb500_pata_exec_command,
- .sff_data_xfer = rb500_pata_data_xfer,
- .freeze = rb500_pata_freeze,
- .thaw = rb500_pata_thaw,
-};
-
-/* ------------------------------------------------------------------------ */
-
-static struct scsi_host_template rb500_pata_sht = {
- ATA_PIO_SHT(DRV_NAME),
-};
-
-/* ------------------------------------------------------------------------ */
-
-static void rb500_pata_setup_ports(struct ata_host *ah)
-{
- struct rb500_cf_info *info = ah->private_data;
- struct ata_port *ap;
-
- ap = ah->ports[0];
-
- ap->ops = &rb500_pata_port_ops;
- ap->pio_mask = 0x1f; /* PIO4 */
- ap->flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO;
-
- ap->ioaddr.cmd_addr = info->iobase + RB500_CF_REG_CMD;
- ap->ioaddr.ctl_addr = info->iobase + RB500_CF_REG_CTRL;
- ap->ioaddr.altstatus_addr = info->iobase + RB500_CF_REG_CTRL;
-
- ata_sff_std_ports(&ap->ioaddr);
-
- ap->ioaddr.data_addr = info->iobase + RB500_CF_REG_DATA;
-}
-
-static __devinit int rb500_pata_driver_probe(struct platform_device *pdev)
-{
- unsigned int irq;
- int gpio;
- struct resource *res;
- struct ata_host *ah;
- struct rb500_cf_info *info;
- int ret;
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res) {
- dev_err(&pdev->dev, "no IOMEM resource found\n");
- return -EINVAL;
- }
-
- irq = platform_get_irq(pdev, 0);
- if (irq <= 0) {
- dev_err(&pdev->dev, "no IRQ resource found\n");
- return -ENOENT;
- }
-
- gpio = irq_to_gpio(irq);
- if (gpio < 0) {
- dev_err(&pdev->dev, "no GPIO found for irq%d\n", irq);
- return -ENOENT;
- }
-
- ret = gpio_request(gpio, DRV_NAME);
- if (ret) {
- dev_err(&pdev->dev, "GPIO request failed\n");
- return ret;
- }
-
- /* allocate host */
- ah = ata_host_alloc(&pdev->dev, RB500_CF_MAXPORTS);
- if (!ah)
- return -ENOMEM;
-
- platform_set_drvdata(pdev, ah);
-
- info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
- if (!info)
- return -ENOMEM;
-
- ah->private_data = info;
- info->gpio_line = gpio;
- info->irq = irq;
-
- info->iobase = devm_ioremap_nocache(&pdev->dev, res->start,
- res->end - res->start + 1);
- if (!info->iobase)
- return -ENOMEM;
-
- ret = gpio_direction_input(gpio);
- if (ret) {
- dev_err(&pdev->dev, "unable to set GPIO direction, err=%d\n",
- ret);
- goto err_free_gpio;
- }
-
- rb500_pata_setup_ports(ah);
-
- ret = ata_host_activate(ah, irq, rb500_pata_irq_handler,
- IRQF_TRIGGER_LOW, &rb500_pata_sht);
- if (ret)
- goto err_free_gpio;
-
- return 0;
-
-err_free_gpio:
- gpio_free(gpio);
-
- return ret;
-}
-
-static __devexit int rb500_pata_driver_remove(struct platform_device *pdev)
-{
- struct ata_host *ah = platform_get_drvdata(pdev);
- struct rb500_cf_info *info = ah->private_data;
-
- ata_host_detach(ah);
- gpio_free(info->gpio_line);
-
- return 0;
-}
-
-/* work with hotplug and coldplug */
-MODULE_ALIAS("platform:" DRV_NAME);
-
-static struct platform_driver rb500_pata_platform_driver = {
- .probe = rb500_pata_driver_probe,
- .remove = __devexit_p(rb500_pata_driver_remove),
- .driver = {
- .name = DRV_NAME,
- .owner = THIS_MODULE,
- },
-};
-
-/* ------------------------------------------------------------------------ */
-
-#define DRV_INFO DRV_DESC " version " DRV_VERSION
-
-static int __init rb500_pata_module_init(void)
-{
- printk(KERN_INFO DRV_INFO "\n");
-
- return platform_driver_register(&rb500_pata_platform_driver);
-}
-
-static void __exit rb500_pata_module_exit(void)
-{
- platform_driver_unregister(&rb500_pata_platform_driver);
-}
-
-MODULE_AUTHOR("Gabor Juhos <juhosg at openwrt.org>");
-MODULE_AUTHOR("Florian Fainelli <florian@openwrt.org>");
-MODULE_DESCRIPTION(DRV_DESC);
-MODULE_VERSION(DRV_VERSION);
-MODULE_LICENSE("GPL");
-
-module_init(rb500_pata_module_init);
-module_exit(rb500_pata_module_exit);
diff --git a/drivers/ata/pata_rb532_cf.c b/drivers/ata/pata_rb532_cf.c
new file mode 100644
index 0000000..a108d25
--- /dev/null
+++ b/drivers/ata/pata_rb532_cf.c
@@ -0,0 +1,277 @@
+/*
+ * A low-level PATA driver to handle a Compact Flash connected on the
+ * Mikrotik's RouterBoard 532 board.
+ *
+ * Copyright (C) 2007 Gabor Juhos <juhosg at openwrt.org>
+ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
+ *
+ * This file was based on: drivers/ata/pata_ixp4xx_cf.c
+ * Copyright (C) 2006-07 Tower Technologies
+ * Author: Alessandro Zummo <a.zummo@towertech.it>
+ *
+ * Also was based on the driver for Linux 2.4.xx published by Mikrotik for
+ * their RouterBoard 1xx and 5xx series devices. The original Mikrotik code
+ * seems not to have a license.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+
+#include <linux/libata.h>
+#include <scsi/scsi_host.h>
+
+#include <asm/gpio.h>
+
+#define DRV_NAME "pata-rb532-cf"
+#define DRV_VERSION "0.1.0"
+#define DRV_DESC "PATA driver for RouterBOARD 532 Compact Flash"
+
+#define RB500_CF_MAXPORTS 1
+#define RB500_CF_IO_DELAY 400
+
+#define RB500_CF_REG_CMD 0x0800
+#define RB500_CF_REG_CTRL 0x080E
+#define RB500_CF_REG_DATA 0x0C00
+
+struct rb532_cf_info {
+ void __iomem *iobase;
+ unsigned int gpio_line;
+ int frozen;
+ unsigned int irq;
+};
+
+/* ------------------------------------------------------------------------ */
+
+static inline void rb532_pata_finish_io(struct ata_port *ap)
+{
+ struct ata_host *ah = ap->host;
+ struct rb532_cf_info *info = ah->private_data;
+
+ ata_sff_altstatus(ap);
+ ndelay(RB500_CF_IO_DELAY);
+
+ set_irq_type(info->irq, IRQ_TYPE_LEVEL_HIGH);
+}
+
+static void rb532_pata_exec_command(struct ata_port *ap,
+ const struct ata_taskfile *tf)
+{
+ writeb(tf->command, ap->ioaddr.command_addr);
+ rb532_pata_finish_io(ap);
+}
+
+static void rb532_pata_data_xfer(struct ata_device *adev, unsigned char *buf,
+ unsigned int buflen, int write_data)
+{
+ struct ata_port *ap = adev->link->ap;
+ void __iomem *ioaddr = ap->ioaddr.data_addr;
+
+ if (write_data) {
+ for (; buflen > 0; buflen--, buf++)
+ writeb(*buf, ioaddr);
+ } else {
+ for (; buflen > 0; buflen--, buf++)
+ *buf = readb(ioaddr);
+ }
+
+ rb532_pata_finish_io(adev->link->ap);
+}
+
+static void rb532_pata_freeze(struct ata_port *ap)
+{
+ struct rb532_cf_info *info = ap->host->private_data;
+
+ info->frozen = 1;
+}
+
+static void rb532_pata_thaw(struct ata_port *ap)
+{
+ struct rb532_cf_info *info = ap->host->private_data;
+
+ info->frozen = 0;
+}
+
+static irqreturn_t rb532_pata_irq_handler(int irq, void *dev_instance)
+{
+ struct ata_host *ah = dev_instance;
+ struct rb532_cf_info *info = ah->private_data;
+
+ if (gpio_get_value(info->gpio_line)) {
+ set_irq_type(info->irq, IRQ_TYPE_LEVEL_LOW);
+ if (!info->frozen)
+ ata_sff_interrupt(info->irq, dev_instance);
+ } else {
+ set_irq_type(info->irq, IRQ_TYPE_LEVEL_HIGH);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static struct ata_port_operations rb532_pata_port_ops = {
+ .inherits = &ata_sff_port_ops,
+ .sff_exec_command = rb532_pata_exec_command,
+ .sff_data_xfer = rb532_pata_data_xfer,
+ .freeze = rb532_pata_freeze,
+ .thaw = rb532_pata_thaw,
+};
+
+/* ------------------------------------------------------------------------ */
+
+static struct scsi_host_template rb532_pata_sht = {
+ ATA_PIO_SHT(DRV_NAME),
+};
+
+/* ------------------------------------------------------------------------ */
+
+static void rb532_pata_setup_ports(struct ata_host *ah)
+{
+ struct rb532_cf_info *info = ah->private_data;
+ struct ata_port *ap;
+
+ ap = ah->ports[0];
+
+ ap->ops = &rb532_pata_port_ops;
+ ap->pio_mask = 0x1f; /* PIO4 */
+ ap->flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO;
+
+ ap->ioaddr.cmd_addr = info->iobase + RB500_CF_REG_CMD;
+ ap->ioaddr.ctl_addr = info->iobase + RB500_CF_REG_CTRL;
+ ap->ioaddr.altstatus_addr = info->iobase + RB500_CF_REG_CTRL;
+
+ ata_sff_std_ports(&ap->ioaddr);
+
+ ap->ioaddr.data_addr = info->iobase + RB500_CF_REG_DATA;
+}
+
+static __devinit int rb532_pata_driver_probe(struct platform_device *pdev)
+{
+ unsigned int irq;
+ int gpio;
+ struct resource *res;
+ struct ata_host *ah;
+ struct rb532_cf_info *info;
+ int ret;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "no IOMEM resource found\n");
+ return -EINVAL;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq <= 0) {
+ dev_err(&pdev->dev, "no IRQ resource found\n");
+ return -ENOENT;
+ }
+
+ gpio = irq_to_gpio(irq);
+ if (gpio < 0) {
+ dev_err(&pdev->dev, "no GPIO found for irq%d\n", irq);
+ return -ENOENT;
+ }
+
+ ret = gpio_request(gpio, DRV_NAME);
+ if (ret) {
+ dev_err(&pdev->dev, "GPIO request failed\n");
+ return ret;
+ }
+
+ /* allocate host */
+ ah = ata_host_alloc(&pdev->dev, RB500_CF_MAXPORTS);
+ if (!ah)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, ah);
+
+ info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+
+ ah->private_data = info;
+ info->gpio_line = gpio;
+ info->irq = irq;
+
+ info->iobase = devm_ioremap_nocache(&pdev->dev, res->start,
+ res->end - res->start + 1);
+ if (!info->iobase)
+ return -ENOMEM;
+
+ ret = gpio_direction_input(gpio);
+ if (ret) {
+ dev_err(&pdev->dev, "unable to set GPIO direction, err=%d\n",
+ ret);
+ goto err_free_gpio;
+ }
+
+ rb532_pata_setup_ports(ah);
+
+ ret = ata_host_activate(ah, irq, rb532_pata_irq_handler,
+ IRQF_TRIGGER_LOW, &rb532_pata_sht);
+ if (ret)
+ goto err_free_gpio;
+
+ return 0;
+
+err_free_gpio:
+ gpio_free(gpio);
+
+ return ret;
+}
+
+static __devexit int rb532_pata_driver_remove(struct platform_device *pdev)
+{
+ struct ata_host *ah = platform_get_drvdata(pdev);
+ struct rb532_cf_info *info = ah->private_data;
+
+ ata_host_detach(ah);
+ gpio_free(info->gpio_line);
+
+ return 0;
+}
+
+/* work with hotplug and coldplug */
+MODULE_ALIAS("platform:" DRV_NAME);
+
+static struct platform_driver rb532_pata_platform_driver = {
+ .probe = rb532_pata_driver_probe,
+ .remove = __devexit_p(rb532_pata_driver_remove),
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+/* ------------------------------------------------------------------------ */
+
+#define DRV_INFO DRV_DESC " version " DRV_VERSION
+
+static int __init rb532_pata_module_init(void)
+{
+ printk(KERN_INFO DRV_INFO "\n");
+
+ return platform_driver_register(&rb532_pata_platform_driver);
+}
+
+static void __exit rb532_pata_module_exit(void)
+{
+ platform_driver_unregister(&rb532_pata_platform_driver);
+}
+
+MODULE_AUTHOR("Gabor Juhos <juhosg at openwrt.org>");
+MODULE_AUTHOR("Florian Fainelli <florian@openwrt.org>");
+MODULE_DESCRIPTION(DRV_DESC);
+MODULE_VERSION(DRV_VERSION);
+MODULE_LICENSE("GPL");
+
+module_init(rb532_pata_module_init);
+module_exit(rb532_pata_module_exit);
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 26a6337..842b1a1 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -172,10 +172,11 @@ enum {
PCIE_IRQ_MASK_OFS = 0x1910,
PCIE_UNMASK_ALL_IRQS = 0x40a, /* assorted bits */
- HC_MAIN_IRQ_CAUSE_OFS = 0x1d60,
- HC_MAIN_IRQ_MASK_OFS = 0x1d64,
- HC_SOC_MAIN_IRQ_CAUSE_OFS = 0x20020,
- HC_SOC_MAIN_IRQ_MASK_OFS = 0x20024,
+ /* Host Controller Main Interrupt Cause/Mask registers (1 per-chip) */
+ PCI_HC_MAIN_IRQ_CAUSE_OFS = 0x1d60,
+ PCI_HC_MAIN_IRQ_MASK_OFS = 0x1d64,
+ SOC_HC_MAIN_IRQ_CAUSE_OFS = 0x20020,
+ SOC_HC_MAIN_IRQ_MASK_OFS = 0x20024,
ERR_IRQ = (1 << 0), /* shift by port # */
DONE_IRQ = (1 << 1), /* shift by port # */
HC0_IRQ_PEND = 0x1ff, /* bits 0-8 = HC0's ports */
@@ -445,8 +446,8 @@ struct mv_host_priv {
const struct mv_hw_ops *ops;
int n_ports;
void __iomem *base;
- void __iomem *main_cause_reg_addr;
- void __iomem *main_mask_reg_addr;
+ void __iomem *main_irq_cause_addr;
+ void __iomem *main_irq_mask_addr;
u32 irq_cause_ofs;
u32 irq_mask_ofs;
u32 unmask_all_irqs;
@@ -727,8 +728,8 @@ static inline unsigned int mv_hardport_from_port(unsigned int port)
* Simple code, with two return values, so macro rather than inline.
*
* port is the sole input, in range 0..7.
- * shift is one output, for use with the main_cause and main_mask registers.
- * hardport is the other output, in range 0..3
+ * shift is one output, for use with main_irq_cause / main_irq_mask registers.
+ * hardport is the other output, in range 0..3.
*
* Note that port and hardport may be the same variable in some cases.
*/
@@ -1679,12 +1680,12 @@ static void mv_process_crpb_entries(struct ata_port *ap, struct mv_port_priv *pp
/**
* mv_host_intr - Handle all interrupts on the given host controller
* @host: host specific structure
- * @main_cause: Main interrupt cause register for the chip.
+ * @main_irq_cause: Main interrupt cause register for the chip.
*
* LOCKING:
* Inherited from caller.
*/
-static int mv_host_intr(struct ata_host *host, u32 main_cause)
+static int mv_host_intr(struct ata_host *host, u32 main_irq_cause)
{
struct mv_host_priv *hpriv = host->private_data;
void __iomem *mmio = hpriv->base, *hc_mmio = NULL;
@@ -1705,7 +1706,7 @@ static int mv_host_intr(struct ata_host *host, u32 main_cause)
* Do nothing if port is not interrupting or is disabled:
*/
MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport);
- port_cause = (main_cause >> shift) & (DONE_IRQ | ERR_IRQ);
+ port_cause = (main_irq_cause >> shift) & (DONE_IRQ | ERR_IRQ);
if (!port_cause || !ap || (ap->flags & ATA_FLAG_DISABLED))
continue;
/*
@@ -1811,20 +1812,20 @@ static irqreturn_t mv_interrupt(int irq, void *dev_instance)
struct ata_host *host = dev_instance;
struct mv_host_priv *hpriv = host->private_data;
unsigned int handled = 0;
- u32 main_cause, main_mask;
+ u32 main_irq_cause, main_irq_mask;
spin_lock(&host->lock);
- main_cause = readl(hpriv->main_cause_reg_addr);
- main_mask = readl(hpriv->main_mask_reg_addr);
+ main_irq_cause = readl(hpriv->main_irq_cause_addr);
+ main_irq_mask = readl(hpriv->main_irq_mask_addr);
/*
* Deal with cases where we either have nothing pending, or have read
* a bogus register value which can indicate HW removal or PCI fault.
*/
- if ((main_cause & main_mask) && (main_cause != 0xffffffffU)) {
- if (unlikely((main_cause & PCI_ERR) && HAS_PCI(host)))
+ if ((main_irq_cause & main_irq_mask) && (main_irq_cause != 0xffffffffU)) {
+ if (unlikely((main_irq_cause & PCI_ERR) && HAS_PCI(host)))
handled = mv_pci_error(host, hpriv->base);
else
- handled = mv_host_intr(host, main_cause);
+ handled = mv_host_intr(host, main_irq_cause);
}
spin_unlock(&host->lock);
return IRQ_RETVAL(handled);
@@ -2027,7 +2028,7 @@ static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio)
ZERO(MV_PCI_DISC_TIMER);
ZERO(MV_PCI_MSI_TRIGGER);
writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT);
- ZERO(HC_MAIN_IRQ_MASK_OFS);
+ ZERO(PCI_HC_MAIN_IRQ_MASK_OFS);
ZERO(MV_PCI_SERR_MASK);
ZERO(hpriv->irq_cause_ofs);
ZERO(hpriv->irq_mask_ofs);
@@ -2404,7 +2405,7 @@ static void mv_eh_freeze(struct ata_port *ap)
{
struct mv_host_priv *hpriv = ap->host->private_data;
unsigned int shift, hardport, port = ap->port_no;
- u32 main_mask;
+ u32 main_irq_mask;
/* FIXME: handle coalescing completion events properly */
@@ -2412,9 +2413,9 @@ static void mv_eh_freeze(struct ata_port *ap)
MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport);
/* disable assertion of portN err, done events */
- main_mask = readl(hpriv->main_mask_reg_addr);
- main_mask &= ~((DONE_IRQ | ERR_IRQ) << shift);
- writelfl(main_mask, hpriv->main_mask_reg_addr);
+ main_irq_mask = readl(hpriv->main_irq_mask_addr);
+ main_irq_mask &= ~((DONE_IRQ | ERR_IRQ) << shift);
+ writelfl(main_irq_mask, hpriv->main_irq_mask_addr);
}
static void mv_eh_thaw(struct ata_port *ap)
@@ -2423,7 +2424,7 @@ static void mv_eh_thaw(struct ata_port *ap)
unsigned int shift, hardport, port = ap->port_no;
void __iomem *hc_mmio = mv_hc_base_from_port(hpriv->base, port);
void __iomem *port_mmio = mv_ap_base(ap);
- u32 main_mask, hc_irq_cause;
+ u32 main_irq_mask, hc_irq_cause;
/* FIXME: handle coalescing completion events properly */
@@ -2438,9 +2439,9 @@ static void mv_eh_thaw(struct ata_port *ap)
writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
/* enable assertion of portN err, done events */
- main_mask = readl(hpriv->main_mask_reg_addr);
- main_mask |= ((DONE_IRQ | ERR_IRQ) << shift);
- writelfl(main_mask, hpriv->main_mask_reg_addr);
+ main_irq_mask = readl(hpriv->main_irq_mask_addr);
+ main_irq_mask |= ((DONE_IRQ | ERR_IRQ) << shift);
+ writelfl(main_irq_mask, hpriv->main_irq_mask_addr);
}
/**
@@ -2654,15 +2655,15 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
goto done;
if (HAS_PCI(host)) {
- hpriv->main_cause_reg_addr = mmio + HC_MAIN_IRQ_CAUSE_OFS;
- hpriv->main_mask_reg_addr = mmio + HC_MAIN_IRQ_MASK_OFS;
+ hpriv->main_irq_cause_addr = mmio + PCI_HC_MAIN_IRQ_CAUSE_OFS;
+ hpriv->main_irq_mask_addr = mmio + PCI_HC_MAIN_IRQ_MASK_OFS;
} else {
- hpriv->main_cause_reg_addr = mmio + HC_SOC_MAIN_IRQ_CAUSE_OFS;
- hpriv->main_mask_reg_addr = mmio + HC_SOC_MAIN_IRQ_MASK_OFS;
+ hpriv->main_irq_cause_addr = mmio + SOC_HC_MAIN_IRQ_CAUSE_OFS;
+ hpriv->main_irq_mask_addr = mmio + SOC_HC_MAIN_IRQ_MASK_OFS;
}
/* global interrupt mask: 0 == mask everything */
- writel(0, hpriv->main_mask_reg_addr);
+ writel(0, hpriv->main_irq_mask_addr);
n_hc = mv_get_hc_count(host->ports[0]->flags);
@@ -2712,23 +2713,23 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_ofs);
if (IS_GEN_I(hpriv))
writelfl(~HC_MAIN_MASKED_IRQS_5,
- hpriv->main_mask_reg_addr);
+ hpriv->main_irq_mask_addr);
else
writelfl(~HC_MAIN_MASKED_IRQS,
- hpriv->main_mask_reg_addr);
+ hpriv->main_irq_mask_addr);
VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x "
"PCI int cause/mask=0x%08x/0x%08x\n",
- readl(hpriv->main_cause_reg_addr),
- readl(hpriv->main_mask_reg_addr),
+ readl(hpriv->main_irq_cause_addr),
+ readl(hpriv->main_irq_mask_addr),
readl(mmio + hpriv->irq_cause_ofs),
readl(mmio + hpriv->irq_mask_ofs));
} else {
writelfl(~HC_MAIN_MASKED_IRQS_SOC,
- hpriv->main_mask_reg_addr);
+ hpriv->main_irq_mask_addr);
VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x\n",
- readl(hpriv->main_cause_reg_addr),
- readl(hpriv->main_mask_reg_addr));
+ readl(hpriv->main_irq_cause_addr),
+ readl(hpriv->main_irq_mask_addr));
}
done:
return rc;
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2008-02-25 22:38 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2008-02-25 22:38 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
(additional explanation for the revert is in the full changeset
description)
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/libata-core.c | 5 ++++-
drivers/ata/libata.h | 1 -
2 files changed, 4 insertions(+), 2 deletions(-)
Adrian Bunk (1):
make atapi_dmadir static
Jeff Garzik (1):
Revert "power_state: get rid of write-only variable in SATA"
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index fbc2435..4fbcce7 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -113,7 +113,7 @@ int atapi_enabled = 1;
module_param(atapi_enabled, int, 0444);
MODULE_PARM_DESC(atapi_enabled, "Enable discovery of ATAPI devices (0=off, 1=on)");
-int atapi_dmadir = 0;
+static int atapi_dmadir = 0;
module_param(atapi_dmadir, int, 0444);
MODULE_PARM_DESC(atapi_dmadir, "Enable ATAPI DMADIR bridge support (0=off, 1=on)");
@@ -6567,6 +6567,8 @@ int ata_host_suspend(struct ata_host *host, pm_message_t mesg)
ata_lpm_enable(host);
rc = ata_host_request_pm(host, mesg, 0, ATA_EHI_QUIET, 1);
+ if (rc == 0)
+ host->dev->power.power_state = mesg;
return rc;
}
@@ -6585,6 +6587,7 @@ void ata_host_resume(struct ata_host *host)
{
ata_host_request_pm(host, PMSG_ON, ATA_EH_SOFTRESET,
ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET, 0);
+ host->dev->power.power_state = PMSG_ON;
/* reenable link pm */
ata_lpm_disable(host);
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index 6036ded..aa884f7 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -56,7 +56,6 @@ enum {
extern unsigned int ata_print_id;
extern struct workqueue_struct *ata_aux_wq;
extern int atapi_enabled;
-extern int atapi_dmadir;
extern int atapi_passthru16;
extern int libata_fua;
extern int libata_noacpi;
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2008-02-06 12:14 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2008-02-06 12:14 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
arch/arm/mach-rpc/riscpc.c | 2 +-
arch/blackfin/mach-bf527/boards/ezkit.c | 2 +-
arch/blackfin/mach-bf533/boards/H8606.c | 2 +-
arch/blackfin/mach-bf533/boards/cm_bf533.c | 2 +-
arch/blackfin/mach-bf533/boards/ezkit.c | 2 +-
arch/blackfin/mach-bf533/boards/stamp.c | 2 +-
arch/blackfin/mach-bf537/boards/cm_bf537.c | 2 +-
arch/blackfin/mach-bf537/boards/generic_board.c | 2 +-
arch/blackfin/mach-bf537/boards/minotaur.c | 2 +-
arch/blackfin/mach-bf537/boards/stamp.c | 2 +-
arch/blackfin/mach-bf561/boards/cm_bf561.c | 2 +-
arch/blackfin/mach-bf561/boards/ezkit.c | 2 +-
arch/sh/boards/landisk/setup.c | 2 +-
arch/sh/boards/lboxre2/setup.c | 2 +-
arch/sh/boards/renesas/r7780rp/setup.c | 2 +-
arch/sh/boards/renesas/rts7751r2d/setup.c | 2 +-
arch/sh/boards/renesas/sdk7780/setup.c | 2 +-
arch/sh/boards/se/7722/setup.c | 2 +-
drivers/ata/ahci.c | 35 +-
drivers/ata/ata_piix.c | 3 +-
drivers/ata/libata-core.c | 2 -
drivers/ata/pata_of_platform.c | 2 +-
drivers/ata/pata_platform.c | 2 +-
drivers/ata/sata_fsl.c | 4 +-
drivers/ata/sata_mv.c | 366 ++++++++++++++++++---
drivers/ata/sata_nv.c | 78 ++++-
drivers/ata/sata_via.c | 2 -
drivers/ide/legacy/ide_platform.c | 2 +-
include/linux/{pata_platform.h => ata_platform.h} | 13 +-
include/linux/libata.h | 2 -
30 files changed, 440 insertions(+), 107 deletions(-)
rename include/linux/{pata_platform.h => ata_platform.h} (75%)
Adrian Bunk (1):
ata_piix.c:piix_init_one() must be __devinit
Alejandro Riveira Fernández (1):
sata_via.c: Remove missleading comment.
Andrew Morton (1):
ata: drivers/ata/sata_mv.c needs dmapool.h
David Milburn (1):
libata-core: unblacklist HITACHI drives
James Bottomley (1):
libata: kill now unused n_iter and fix sata_fsl
Jeff Garzik (1):
Rename: linux/pata_platform.h to linux/ata_platform.h
Robert Hancock (1):
sata_nv: fix ATAPI issues with memory over 4GB (v7)
Saeed Bishara (1):
sata_mv: Support SoC controllers
Tejun Heo (1):
ahci: fix CAP.NP and PI handling
diff --git a/arch/arm/mach-rpc/riscpc.c b/arch/arm/mach-rpc/riscpc.c
index a454451..eca558c 100644
--- a/arch/arm/mach-rpc/riscpc.c
+++ b/arch/arm/mach-rpc/riscpc.c
@@ -17,7 +17,7 @@
#include <linux/sched.h>
#include <linux/device.h>
#include <linux/serial_8250.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <asm/elf.h>
#include <asm/io.h>
diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
index f8c411a..1795aab 100644
--- a/arch/blackfin/mach-bf527/boards/ezkit.c
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -37,7 +37,7 @@
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb/isp1362.h>
#endif
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/usb/sl811.h>
diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c
index a72c7a6..97378b0 100644
--- a/arch/blackfin/mach-bf533/boards/H8606.c
+++ b/arch/blackfin/mach-bf533/boards/H8606.c
@@ -38,7 +38,7 @@
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb/isp1362.h>
#endif
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c
index 21df2f3..886f260 100644
--- a/arch/blackfin/mach-bf533/boards/cm_bf533.c
+++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c
@@ -34,7 +34,7 @@
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/usb/isp1362.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
diff --git a/arch/blackfin/mach-bf533/boards/ezkit.c b/arch/blackfin/mach-bf533/boards/ezkit.c
index c37dd45..4026c2f 100644
--- a/arch/blackfin/mach-bf533/boards/ezkit.c
+++ b/arch/blackfin/mach-bf533/boards/ezkit.c
@@ -35,7 +35,7 @@
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/usb/isp1362.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
index ac52b04..0185350 100644
--- a/arch/blackfin/mach-bf533/boards/stamp.c
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -38,7 +38,7 @@
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb/isp1362.h>
#endif
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c
index 8703b67..f7c1f96 100644
--- a/arch/blackfin/mach-bf537/boards/cm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c
@@ -36,7 +36,7 @@
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/usb/isp1362.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
diff --git a/arch/blackfin/mach-bf537/boards/generic_board.c b/arch/blackfin/mach-bf537/boards/generic_board.c
index 3e52f3f..8a3397d 100644
--- a/arch/blackfin/mach-bf537/boards/generic_board.c
+++ b/arch/blackfin/mach-bf537/boards/generic_board.c
@@ -38,7 +38,7 @@
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb/isp1362.h>
#endif
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/usb/sl811.h>
diff --git a/arch/blackfin/mach-bf537/boards/minotaur.c b/arch/blackfin/mach-bf537/boards/minotaur.c
index b8bbba8..d71e0be 100644
--- a/arch/blackfin/mach-bf537/boards/minotaur.c
+++ b/arch/blackfin/mach-bf537/boards/minotaur.c
@@ -10,7 +10,7 @@
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb_isp1362.h>
#endif
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/usb_sl811.h>
diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index 7725415..119e6ea 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -38,7 +38,7 @@
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb/isp1362.h>
#endif
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/usb/sl811.h>
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index 3a79a90..bf9e738 100644
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -34,7 +34,7 @@
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/usb/isp1362.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
diff --git a/arch/blackfin/mach-bf561/boards/ezkit.c b/arch/blackfin/mach-bf561/boards/ezkit.c
index 7601c3b..ed863ce 100644
--- a/arch/blackfin/mach-bf561/boards/ezkit.c
+++ b/arch/blackfin/mach-bf561/boards/ezkit.c
@@ -35,7 +35,7 @@
#include <linux/spi/spi.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/portmux.h>
diff --git a/arch/sh/boards/landisk/setup.c b/arch/sh/boards/landisk/setup.c
index eda7176..2b708ec 100644
--- a/arch/sh/boards/landisk/setup.c
+++ b/arch/sh/boards/landisk/setup.c
@@ -14,7 +14,7 @@
*/
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/pm.h>
#include <linux/mm.h>
#include <asm/machvec.h>
diff --git a/arch/sh/boards/lboxre2/setup.c b/arch/sh/boards/lboxre2/setup.c
index 9c830fd..c74440d 100644
--- a/arch/sh/boards/lboxre2/setup.c
+++ b/arch/sh/boards/lboxre2/setup.c
@@ -13,7 +13,7 @@
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <asm/machvec.h>
#include <asm/addrspace.h>
#include <asm/lboxre2.h>
diff --git a/arch/sh/boards/renesas/r7780rp/setup.c b/arch/sh/boards/renesas/r7780rp/setup.c
index a43b477..f7a8d5c 100644
--- a/arch/sh/boards/renesas/r7780rp/setup.c
+++ b/arch/sh/boards/renesas/r7780rp/setup.c
@@ -15,7 +15,7 @@
*/
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/types.h>
#include <net/ax88796.h>
#include <asm/machvec.h>
diff --git a/arch/sh/boards/renesas/rts7751r2d/setup.c b/arch/sh/boards/renesas/rts7751r2d/setup.c
index 3452b07..a0ef81b 100644
--- a/arch/sh/boards/renesas/rts7751r2d/setup.c
+++ b/arch/sh/boards/renesas/rts7751r2d/setup.c
@@ -10,7 +10,7 @@
*/
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/serial_8250.h>
#include <linux/sm501.h>
#include <linux/sm501-regs.h>
diff --git a/arch/sh/boards/renesas/sdk7780/setup.c b/arch/sh/boards/renesas/sdk7780/setup.c
index 5df32f2..acc5932 100644
--- a/arch/sh/boards/renesas/sdk7780/setup.c
+++ b/arch/sh/boards/renesas/sdk7780/setup.c
@@ -11,7 +11,7 @@
#include <linux/init.h>
#include <linux/types.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <asm/machvec.h>
#include <asm/sdk7780.h>
#include <asm/heartbeat.h>
diff --git a/arch/sh/boards/se/7722/setup.c b/arch/sh/boards/se/7722/setup.c
index eb97dca..b1a3d9d 100644
--- a/arch/sh/boards/se/7722/setup.c
+++ b/arch/sh/boards/se/7722/setup.c
@@ -12,7 +12,7 @@
*/
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <asm/machvec.h>
#include <asm/se7722.h>
#include <asm/io.h>
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 27c8d56..29e71bd 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -679,24 +679,20 @@ static void ahci_save_initial_config(struct pci_dev *pdev,
/* cross check port_map and cap.n_ports */
if (port_map) {
- u32 tmp_port_map = port_map;
- int n_ports = ahci_nr_ports(cap);
+ int map_ports = 0;
- for (i = 0; i < AHCI_MAX_PORTS && n_ports; i++) {
- if (tmp_port_map & (1 << i)) {
- n_ports--;
- tmp_port_map &= ~(1 << i);
- }
- }
+ for (i = 0; i < AHCI_MAX_PORTS; i++)
+ if (port_map & (1 << i))
+ map_ports++;
- /* If n_ports and port_map are inconsistent, whine and
- * clear port_map and let it be generated from n_ports.
+ /* If PI has more ports than n_ports, whine, clear
+ * port_map and let it be generated from n_ports.
*/
- if (n_ports || tmp_port_map) {
+ if (map_ports > ahci_nr_ports(cap)) {
dev_printk(KERN_WARNING, &pdev->dev,
- "nr_ports (%u) and implemented port map "
- "(0x%x) don't match, using nr_ports\n",
- ahci_nr_ports(cap), port_map);
+ "implemented port map (0x%x) contains more "
+ "ports than nr_ports (%u), using nr_ports\n",
+ port_map, ahci_nr_ports(cap));
port_map = 0;
}
}
@@ -2201,7 +2197,7 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
struct device *dev = &pdev->dev;
struct ahci_host_priv *hpriv;
struct ata_host *host;
- int i, rc;
+ int n_ports, i, rc;
VPRINTK("ENTER\n");
@@ -2255,7 +2251,14 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (hpriv->cap & HOST_CAP_PMP)
pi.flags |= ATA_FLAG_PMP;
- host = ata_host_alloc_pinfo(&pdev->dev, ppi, fls(hpriv->port_map));
+ /* CAP.NP sometimes indicate the index of the last enabled
+ * port, at other times, that of the last possible port, so
+ * determining the maximum port number requires looking at
+ * both CAP.NP and port_map.
+ */
+ n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
+
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports);
if (!host)
return -ENOMEM;
host->iomap = pcim_iomap_table(pdev);
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 4b99ed0..9c2515f 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -1603,7 +1603,8 @@ static void piix_iocfg_bit18_quirk(struct pci_dev *pdev)
* Zero on success, or -ERRNO value.
*/
-static int piix_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
+static int __devinit piix_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
{
static int printed_version;
struct device *dev = &pdev->dev;
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 361cf50..3011919 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -4154,8 +4154,6 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
/* NCQ is broken */
{ "Maxtor *", "BANC*", ATA_HORKAGE_NONCQ },
{ "Maxtor 7V300F0", "VA111630", ATA_HORKAGE_NONCQ },
- { "HITACHI HDS7250SASUN500G*", NULL, ATA_HORKAGE_NONCQ },
- { "HITACHI HDS7225SBSUN250G*", NULL, ATA_HORKAGE_NONCQ },
{ "ST380817AS", "3.42", ATA_HORKAGE_NONCQ },
{ "ST3160023AS", "3.42", ATA_HORKAGE_NONCQ },
diff --git a/drivers/ata/pata_of_platform.c b/drivers/ata/pata_of_platform.c
index 938f48a..408da30 100644
--- a/drivers/ata/pata_of_platform.c
+++ b/drivers/ata/pata_of_platform.c
@@ -12,7 +12,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/of_platform.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
static int __devinit pata_of_platform_probe(struct of_device *ofdev,
const struct of_device_id *match)
diff --git a/drivers/ata/pata_platform.c b/drivers/ata/pata_platform.c
index 224bb6c..aad7adc 100644
--- a/drivers/ata/pata_platform.c
+++ b/drivers/ata/pata_platform.c
@@ -19,7 +19,7 @@
#include <linux/ata.h>
#include <linux/libata.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#define DRV_NAME "pata_platform"
#define DRV_VERSION "1.2"
diff --git a/drivers/ata/sata_fsl.c b/drivers/ata/sata_fsl.c
index 922d7b2..efcb66b 100644
--- a/drivers/ata/sata_fsl.c
+++ b/drivers/ata/sata_fsl.c
@@ -355,8 +355,8 @@ static unsigned int sata_fsl_fill_sg(struct ata_queued_cmd *qc, void *cmd_desc,
ata_port_printk(qc->ap, KERN_ERR,
"s/g len unaligned : 0x%x\n", sg_len);
- if ((num_prde == (SATA_FSL_MAX_PRD_DIRECT - 1)) &&
- (qc->n_iter + 1 != qc->n_elem)) {
+ if (num_prde == (SATA_FSL_MAX_PRD_DIRECT - 1) &&
+ sg_next(sg) != NULL) {
VPRINTK("setting indirect prde\n");
prd_ptr_to_indirect_ext = prd;
prd->dba = cpu_to_le32(indirect_ext_segment_paddr);
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 3c1b5c9..080b836 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -69,8 +69,11 @@
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
+#include <linux/dmapool.h>
#include <linux/dma-mapping.h>
#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_device.h>
@@ -179,6 +182,8 @@ enum {
HC_MAIN_IRQ_CAUSE_OFS = 0x1d60,
HC_MAIN_IRQ_MASK_OFS = 0x1d64,
+ HC_SOC_MAIN_IRQ_CAUSE_OFS = 0x20020,
+ HC_SOC_MAIN_IRQ_MASK_OFS = 0x20024,
PORT0_ERR = (1 << 0), /* shift by port # */
PORT0_DONE = (1 << 1), /* shift by port # */
HC0_IRQ_PEND = 0x1ff, /* bits 0-8 = HC0's ports */
@@ -194,11 +199,13 @@ enum {
TWSI_INT = (1 << 24),
HC_MAIN_RSVD = (0x7f << 25), /* bits 31-25 */
HC_MAIN_RSVD_5 = (0x1fff << 19), /* bits 31-19 */
+ HC_MAIN_RSVD_SOC = (0x3fffffb << 6), /* bits 31-9, 7-6 */
HC_MAIN_MASKED_IRQS = (TRAN_LO_DONE | TRAN_HI_DONE |
PORTS_0_7_COAL_DONE | GPIO_INT | TWSI_INT |
HC_MAIN_RSVD),
HC_MAIN_MASKED_IRQS_5 = (PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE |
HC_MAIN_RSVD_5),
+ HC_MAIN_MASKED_IRQS_SOC = (PORTS_0_3_COAL_DONE | HC_MAIN_RSVD_SOC),
/* SATAHC registers */
HC_CFG_OFS = 0,
@@ -368,6 +375,7 @@ enum chip_type {
chip_608x,
chip_6042,
chip_7042,
+ chip_soc,
};
/* Command ReQuest Block: 32B */
@@ -424,6 +432,10 @@ struct mv_host_priv {
u32 hp_flags;
struct mv_port_signal signal[8];
const struct mv_hw_ops *ops;
+ int n_ports;
+ void __iomem *base;
+ void __iomem *main_cause_reg_addr;
+ void __iomem *main_mask_reg_addr;
u32 irq_cause_ofs;
u32 irq_mask_ofs;
u32 unmask_all_irqs;
@@ -482,6 +494,15 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx,
static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int n_hc);
static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio);
+static void mv_soc_enable_leds(struct mv_host_priv *hpriv,
+ void __iomem *mmio);
+static void mv_soc_read_preamp(struct mv_host_priv *hpriv, int idx,
+ void __iomem *mmio);
+static int mv_soc_reset_hc(struct mv_host_priv *hpriv,
+ void __iomem *mmio, unsigned int n_hc);
+static void mv_soc_reset_flash(struct mv_host_priv *hpriv,
+ void __iomem *mmio);
+static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio);
static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio);
static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int port_no);
@@ -661,6 +682,12 @@ static const struct ata_port_info mv_port_info[] = {
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
+ { /* chip_soc */
+ .flags = MV_COMMON_FLAGS | MV_FLAG_SOC,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &mv_iie_ops,
+ },
};
static const struct pci_device_id mv_pci_tbl[] = {
@@ -711,6 +738,15 @@ static const struct mv_hw_ops mv6xxx_ops = {
.reset_bus = mv_reset_pci_bus,
};
+static const struct mv_hw_ops mv_soc_ops = {
+ .phy_errata = mv6_phy_errata,
+ .enable_leds = mv_soc_enable_leds,
+ .read_preamp = mv_soc_read_preamp,
+ .reset_hc = mv_soc_reset_hc,
+ .reset_flash = mv_soc_reset_flash,
+ .reset_bus = mv_soc_reset_bus,
+};
+
/*
* Functions
*/
@@ -749,9 +785,15 @@ static inline void __iomem *mv_port_base(void __iomem *base, unsigned int port)
(mv_hardport_from_port(port) * MV_PORT_REG_SZ);
}
+static inline void __iomem *mv_host_base(struct ata_host *host)
+{
+ struct mv_host_priv *hpriv = host->private_data;
+ return hpriv->base;
+}
+
static inline void __iomem *mv_ap_base(struct ata_port *ap)
{
- return mv_port_base(ap->host->iomap[MV_PRIMARY_BAR], ap->port_no);
+ return mv_port_base(mv_host_base(ap->host), ap->port_no);
}
static inline int mv_get_hc_count(unsigned long port_flags)
@@ -1649,16 +1691,21 @@ static void mv_intr_edma(struct ata_port *ap)
*/
static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc)
{
- void __iomem *mmio = host->iomap[MV_PRIMARY_BAR];
+ struct mv_host_priv *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->base;
void __iomem *hc_mmio = mv_hc_base(mmio, hc);
u32 hc_irq_cause;
- int port, port0;
+ int port, port0, last_port;
if (hc == 0)
port0 = 0;
else
port0 = MV_PORTS_PER_HC;
+ if (HAS_PCI(host))
+ last_port = port0 + MV_PORTS_PER_HC;
+ else
+ last_port = port0 + hpriv->n_ports;
/* we'll need the HC success int register in most cases */
hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
if (!hc_irq_cause)
@@ -1669,7 +1716,7 @@ static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc)
VPRINTK("ENTER, hc%u relevant=0x%08x HC IRQ cause=0x%08x\n",
hc, relevant, hc_irq_cause);
- for (port = port0; port < port0 + MV_PORTS_PER_HC; port++) {
+ for (port = port0; port < port0 + last_port; port++) {
struct ata_port *ap = host->ports[port];
struct mv_port_priv *pp = ap->private_data;
int have_err_bits, hard_port, shift;
@@ -1764,13 +1811,15 @@ static void mv_pci_error(struct ata_host *host, void __iomem *mmio)
static irqreturn_t mv_interrupt(int irq, void *dev_instance)
{
struct ata_host *host = dev_instance;
+ struct mv_host_priv *hpriv = host->private_data;
unsigned int hc, handled = 0, n_hcs;
- void __iomem *mmio = host->iomap[MV_PRIMARY_BAR];
+ void __iomem *mmio = hpriv->base;
u32 irq_stat, irq_mask;
spin_lock(&host->lock);
- irq_stat = readl(mmio + HC_MAIN_IRQ_CAUSE_OFS);
- irq_mask = readl(mmio + HC_MAIN_IRQ_MASK_OFS);
+
+ irq_stat = readl(hpriv->main_cause_reg_addr);
+ irq_mask = readl(hpriv->main_mask_reg_addr);
/* check the cases where we either have nothing pending or have read
* a bogus register value which can indicate HW removal or PCI fault
@@ -1827,7 +1876,8 @@ static unsigned int mv5_scr_offset(unsigned int sc_reg_in)
static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val)
{
- void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ void __iomem *mmio = hpriv->base;
void __iomem *addr = mv5_phy_base(mmio, ap->port_no);
unsigned int ofs = mv5_scr_offset(sc_reg_in);
@@ -1840,7 +1890,8 @@ static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val)
static int mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
{
- void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ void __iomem *mmio = hpriv->base;
void __iomem *addr = mv5_phy_base(mmio, ap->port_no);
unsigned int ofs = mv5_scr_offset(sc_reg_in);
@@ -2178,6 +2229,93 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
writel(m2, port_mmio + PHY_MODE2);
}
+/* TODO: use the generic LED interface to configure the SATA Presence */
+/* & Acitivy LEDs on the board */
+static void mv_soc_enable_leds(struct mv_host_priv *hpriv,
+ void __iomem *mmio)
+{
+ return;
+}
+
+static void mv_soc_read_preamp(struct mv_host_priv *hpriv, int idx,
+ void __iomem *mmio)
+{
+ void __iomem *port_mmio;
+ u32 tmp;
+
+ port_mmio = mv_port_base(mmio, idx);
+ tmp = readl(port_mmio + PHY_MODE2);
+
+ hpriv->signal[idx].amps = tmp & 0x700; /* bits 10:8 */
+ hpriv->signal[idx].pre = tmp & 0xe0; /* bits 7:5 */
+}
+
+#undef ZERO
+#define ZERO(reg) writel(0, port_mmio + (reg))
+static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv,
+ void __iomem *mmio, unsigned int port)
+{
+ void __iomem *port_mmio = mv_port_base(mmio, port);
+
+ writelfl(EDMA_DS, port_mmio + EDMA_CMD_OFS);
+
+ mv_channel_reset(hpriv, mmio, port);
+
+ ZERO(0x028); /* command */
+ writel(0x101f, port_mmio + EDMA_CFG_OFS);
+ ZERO(0x004); /* timer */
+ ZERO(0x008); /* irq err cause */
+ ZERO(0x00c); /* irq err mask */
+ ZERO(0x010); /* rq bah */
+ ZERO(0x014); /* rq inp */
+ ZERO(0x018); /* rq outp */
+ ZERO(0x01c); /* respq bah */
+ ZERO(0x024); /* respq outp */
+ ZERO(0x020); /* respq inp */
+ ZERO(0x02c); /* test control */
+ writel(0xbc, port_mmio + EDMA_IORDY_TMOUT);
+}
+
+#undef ZERO
+
+#define ZERO(reg) writel(0, hc_mmio + (reg))
+static void mv_soc_reset_one_hc(struct mv_host_priv *hpriv,
+ void __iomem *mmio)
+{
+ void __iomem *hc_mmio = mv_hc_base(mmio, 0);
+
+ ZERO(0x00c);
+ ZERO(0x010);
+ ZERO(0x014);
+
+}
+
+#undef ZERO
+
+static int mv_soc_reset_hc(struct mv_host_priv *hpriv,
+ void __iomem *mmio, unsigned int n_hc)
+{
+ unsigned int port;
+
+ for (port = 0; port < hpriv->n_ports; port++)
+ mv_soc_reset_hc_port(hpriv, mmio, port);
+
+ mv_soc_reset_one_hc(hpriv, mmio);
+
+ return 0;
+}
+
+static void mv_soc_reset_flash(struct mv_host_priv *hpriv,
+ void __iomem *mmio)
+{
+ return;
+}
+
+static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio)
+{
+ return;
+}
+
static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int port_no)
{
@@ -2342,7 +2480,7 @@ static int mv_hardreset(struct ata_link *link, unsigned int *class,
{
struct ata_port *ap = link->ap;
struct mv_host_priv *hpriv = ap->host->private_data;
- void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ void __iomem *mmio = hpriv->base;
mv_stop_dma(ap);
@@ -2383,7 +2521,7 @@ static void mv_error_handler(struct ata_port *ap)
static void mv_eh_freeze(struct ata_port *ap)
{
- void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ struct mv_host_priv *hpriv = ap->host->private_data;
unsigned int hc = (ap->port_no > 3) ? 1 : 0;
u32 tmp, mask;
unsigned int shift;
@@ -2397,13 +2535,14 @@ static void mv_eh_freeze(struct ata_port *ap)
mask = 0x3 << shift;
/* disable assertion of portN err, done events */
- tmp = readl(mmio + HC_MAIN_IRQ_MASK_OFS);
- writelfl(tmp & ~mask, mmio + HC_MAIN_IRQ_MASK_OFS);
+ tmp = readl(hpriv->main_mask_reg_addr);
+ writelfl(tmp & ~mask, hpriv->main_mask_reg_addr);
}
static void mv_eh_thaw(struct ata_port *ap)
{
- void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ void __iomem *mmio = hpriv->base;
unsigned int hc = (ap->port_no > 3) ? 1 : 0;
void __iomem *hc_mmio = mv_hc_base(mmio, hc);
void __iomem *port_mmio = mv_ap_base(ap);
@@ -2430,8 +2569,8 @@ static void mv_eh_thaw(struct ata_port *ap)
writel(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
/* enable assertion of portN err, done events */
- tmp = readl(mmio + HC_MAIN_IRQ_MASK_OFS);
- writelfl(tmp | mask, mmio + HC_MAIN_IRQ_MASK_OFS);
+ tmp = readl(hpriv->main_mask_reg_addr);
+ writelfl(tmp | mask, hpriv->main_mask_reg_addr);
}
/**
@@ -2598,9 +2737,13 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
break;
}
break;
+ case chip_soc:
+ hpriv->ops = &mv_soc_ops;
+ hp_flags |= MV_HP_ERRATA_60X1C0;
+ break;
default:
- dev_printk(KERN_ERR, &pdev->dev,
+ dev_printk(KERN_ERR, host->dev,
"BUG: invalid board index %u\n", board_idx);
return 1;
}
@@ -2633,15 +2776,25 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
static int mv_init_host(struct ata_host *host, unsigned int board_idx)
{
int rc = 0, n_hc, port, hc;
- void __iomem *mmio = host->iomap[MV_PRIMARY_BAR];
struct mv_host_priv *hpriv = host->private_data;
-
- /* global interrupt mask */
- writel(0, mmio + HC_MAIN_IRQ_MASK_OFS);
+ void __iomem *mmio = hpriv->base;
rc = mv_chip_id(host, board_idx);
if (rc)
- goto done;
+ goto done;
+
+ if (HAS_PCI(host)) {
+ hpriv->main_cause_reg_addr = hpriv->base +
+ HC_MAIN_IRQ_CAUSE_OFS;
+ hpriv->main_mask_reg_addr = hpriv->base + HC_MAIN_IRQ_MASK_OFS;
+ } else {
+ hpriv->main_cause_reg_addr = hpriv->base +
+ HC_SOC_MAIN_IRQ_CAUSE_OFS;
+ hpriv->main_mask_reg_addr = hpriv->base +
+ HC_SOC_MAIN_IRQ_MASK_OFS;
+ }
+ /* global interrupt mask */
+ writel(0, hpriv->main_mask_reg_addr);
n_hc = mv_get_hc_count(host->ports[0]->flags);
@@ -2672,13 +2825,15 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
for (port = 0; port < host->n_ports; port++) {
struct ata_port *ap = host->ports[port];
void __iomem *port_mmio = mv_port_base(mmio, port);
- unsigned int offset = port_mmio - mmio;
mv_port_init(&ap->ioaddr, port_mmio);
#ifdef CONFIG_PCI
- ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio");
- ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port");
+ if (HAS_PCI(host)) {
+ unsigned int offset = port_mmio - mmio;
+ ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio");
+ ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port");
+ }
#endif
}
@@ -2694,35 +2849,141 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
writelfl(0, hc_mmio + HC_IRQ_CAUSE_OFS);
}
- /* Clear any currently outstanding host interrupt conditions */
- writelfl(0, mmio + hpriv->irq_cause_ofs);
+ if (HAS_PCI(host)) {
+ /* Clear any currently outstanding host interrupt conditions */
+ writelfl(0, mmio + hpriv->irq_cause_ofs);
- /* and unmask interrupt generation for host regs */
- writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_ofs);
+ /* and unmask interrupt generation for host regs */
+ writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_ofs);
+ if (IS_GEN_I(hpriv))
+ writelfl(~HC_MAIN_MASKED_IRQS_5,
+ hpriv->main_mask_reg_addr);
+ else
+ writelfl(~HC_MAIN_MASKED_IRQS,
+ hpriv->main_mask_reg_addr);
+
+ VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x "
+ "PCI int cause/mask=0x%08x/0x%08x\n",
+ readl(hpriv->main_cause_reg_addr),
+ readl(hpriv->main_mask_reg_addr),
+ readl(mmio + hpriv->irq_cause_ofs),
+ readl(mmio + hpriv->irq_mask_ofs));
+ } else {
+ writelfl(~HC_MAIN_MASKED_IRQS_SOC,
+ hpriv->main_mask_reg_addr);
+ VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x\n",
+ readl(hpriv->main_cause_reg_addr),
+ readl(hpriv->main_mask_reg_addr));
+ }
+done:
+ return rc;
+}
- if (IS_GEN_I(hpriv))
- writelfl(~HC_MAIN_MASKED_IRQS_5, mmio + HC_MAIN_IRQ_MASK_OFS);
- else
- writelfl(~HC_MAIN_MASKED_IRQS, mmio + HC_MAIN_IRQ_MASK_OFS);
+/**
+ * mv_platform_probe - handle a positive probe of an soc Marvell
+ * host
+ * @pdev: platform device found
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static int mv_platform_probe(struct platform_device *pdev)
+{
+ static int printed_version;
+ const struct mv_sata_platform_data *mv_platform_data;
+ const struct ata_port_info *ppi[] =
+ { &mv_port_info[chip_soc], NULL };
+ struct ata_host *host;
+ struct mv_host_priv *hpriv;
+ struct resource *res;
+ int n_ports, rc;
- VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x "
- "PCI int cause/mask=0x%08x/0x%08x\n",
- readl(mmio + HC_MAIN_IRQ_CAUSE_OFS),
- readl(mmio + HC_MAIN_IRQ_MASK_OFS),
- readl(mmio + hpriv->irq_cause_ofs),
- readl(mmio + hpriv->irq_mask_ofs));
+ if (!printed_version++)
+ dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
-done:
- return rc;
+ /*
+ * Simple resource validation ..
+ */
+ if (unlikely(pdev->num_resources != 2)) {
+ dev_err(&pdev->dev, "invalid number of resources\n");
+ return -EINVAL;
+ }
+
+ /*
+ * Get the register base first
+ */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (res == NULL)
+ return -EINVAL;
+
+ /* allocate host */
+ mv_platform_data = pdev->dev.platform_data;
+ n_ports = mv_platform_data->n_ports;
+
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports);
+ hpriv = devm_kzalloc(&pdev->dev, sizeof(*hpriv), GFP_KERNEL);
+
+ if (!host || !hpriv)
+ return -ENOMEM;
+ host->private_data = hpriv;
+ hpriv->n_ports = n_ports;
+
+ host->iomap = NULL;
+ hpriv->base = ioremap(res->start, res->end - res->start + 1);
+ hpriv->base -= MV_SATAHC0_REG_BASE;
+
+ /* initialize adapter */
+ rc = mv_init_host(host, chip_soc);
+ if (rc)
+ return rc;
+
+ dev_printk(KERN_INFO, &pdev->dev,
+ "slots %u ports %d\n", (unsigned)MV_MAX_Q_DEPTH,
+ host->n_ports);
+
+ return ata_host_activate(host, platform_get_irq(pdev, 0), mv_interrupt,
+ IRQF_SHARED, &mv6_sht);
+}
+
+/*
+ *
+ * mv_platform_remove - unplug a platform interface
+ * @pdev: platform device
+ *
+ * A platform bus SATA device has been unplugged. Perform the needed
+ * cleanup. Also called on module unload for any active devices.
+ */
+static int __devexit mv_platform_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ata_host *host = dev_get_drvdata(dev);
+ struct mv_host_priv *hpriv = host->private_data;
+ void __iomem *base = hpriv->base;
+
+ ata_host_detach(host);
+ iounmap(base);
+ return 0;
}
+static struct platform_driver mv_platform_driver = {
+ .probe = mv_platform_probe,
+ .remove = __devexit_p(mv_platform_remove),
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+
#ifdef CONFIG_PCI
-static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
+static int mv_pci_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent);
+
static struct pci_driver mv_pci_driver = {
.name = DRV_NAME,
.id_table = mv_pci_tbl,
- .probe = mv_init_one,
+ .probe = mv_pci_init_one,
.remove = ata_pci_remove_one,
};
@@ -2828,14 +3089,15 @@ static int mv_create_dma_pools(struct mv_host_priv *hpriv, struct device *dev)
}
/**
- * mv_init_one - handle a positive probe of a Marvell host
+ * mv_pci_init_one - handle a positive probe of a PCI Marvell host
* @pdev: PCI device found
* @ent: PCI device ID entry for the matched host
*
* LOCKING:
* Inherited from caller.
*/
-static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
+static int mv_pci_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
{
static int printed_version;
unsigned int board_idx = (unsigned int)ent->driver_data;
@@ -2855,6 +3117,7 @@ static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (!host || !hpriv)
return -ENOMEM;
host->private_data = hpriv;
+ hpriv->n_ports = n_ports;
/* acquire resources */
rc = pcim_enable_device(pdev);
@@ -2867,6 +3130,7 @@ static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (rc)
return rc;
host->iomap = pcim_iomap_table(pdev);
+ hpriv->base = host->iomap[MV_PRIMARY_BAR];
rc = pci_go_64(pdev);
if (rc)
@@ -2895,11 +3159,22 @@ static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
}
#endif
+static int mv_platform_probe(struct platform_device *pdev);
+static int __devexit mv_platform_remove(struct platform_device *pdev);
+
static int __init mv_init(void)
{
int rc = -ENODEV;
#ifdef CONFIG_PCI
rc = pci_register_driver(&mv_pci_driver);
+ if (rc < 0)
+ return rc;
+#endif
+ rc = platform_driver_register(&mv_platform_driver);
+
+#ifdef CONFIG_PCI
+ if (rc < 0)
+ pci_unregister_driver(&mv_pci_driver);
#endif
return rc;
}
@@ -2909,6 +3184,7 @@ static void __exit mv_exit(void)
#ifdef CONFIG_PCI
pci_unregister_driver(&mv_pci_driver);
#endif
+ platform_driver_unregister(&mv_platform_driver);
}
MODULE_AUTHOR("Brett Russ");
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index bfe92a4..ed5473b 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -247,6 +247,7 @@ struct nv_adma_port_priv {
void __iomem *ctl_block;
void __iomem *gen_block;
void __iomem *notifier_clear_block;
+ u64 adma_dma_mask;
u8 flags;
int last_issue_ncq;
};
@@ -715,9 +716,10 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
{
struct ata_port *ap = ata_shost_to_port(sdev->host);
struct nv_adma_port_priv *pp = ap->private_data;
+ struct nv_adma_port_priv *port0, *port1;
+ struct scsi_device *sdev0, *sdev1;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u64 bounce_limit;
- unsigned long segment_boundary;
+ unsigned long segment_boundary, flags;
unsigned short sg_tablesize;
int rc;
int adma_enable;
@@ -729,6 +731,8 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
/* Not a proper libata device, ignore */
return rc;
+ spin_lock_irqsave(ap->lock, flags);
+
if (ap->link.device[sdev->id].class == ATA_DEV_ATAPI) {
/*
* NVIDIA reports that ADMA mode does not support ATAPI commands.
@@ -737,7 +741,6 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
* Restrict DMA parameters as required by the legacy interface
* when an ATAPI device is connected.
*/
- bounce_limit = ATA_DMA_MASK;
segment_boundary = ATA_DMA_BOUNDARY;
/* Subtract 1 since an extra entry may be needed for padding, see
libata-scsi.c */
@@ -748,7 +751,6 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
adma_enable = 0;
nv_adma_register_mode(ap);
} else {
- bounce_limit = *ap->dev->dma_mask;
segment_boundary = NV_ADMA_DMA_BOUNDARY;
sg_tablesize = NV_ADMA_SGTBL_TOTAL_LEN;
adma_enable = 1;
@@ -774,12 +776,49 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
if (current_reg != new_reg)
pci_write_config_dword(pdev, NV_MCP_SATA_CFG_20, new_reg);
- blk_queue_bounce_limit(sdev->request_queue, bounce_limit);
+ port0 = ap->host->ports[0]->private_data;
+ port1 = ap->host->ports[1]->private_data;
+ sdev0 = ap->host->ports[0]->link.device[0].sdev;
+ sdev1 = ap->host->ports[1]->link.device[0].sdev;
+ if ((port0->flags & NV_ADMA_ATAPI_SETUP_COMPLETE) ||
+ (port1->flags & NV_ADMA_ATAPI_SETUP_COMPLETE)) {
+ /** We have to set the DMA mask to 32-bit if either port is in
+ ATAPI mode, since they are on the same PCI device which is
+ used for DMA mapping. If we set the mask we also need to set
+ the bounce limit on both ports to ensure that the block
+ layer doesn't feed addresses that cause DMA mapping to
+ choke. If either SCSI device is not allocated yet, it's OK
+ since that port will discover its correct setting when it
+ does get allocated.
+ Note: Setting 32-bit mask should not fail. */
+ if (sdev0)
+ blk_queue_bounce_limit(sdev0->request_queue,
+ ATA_DMA_MASK);
+ if (sdev1)
+ blk_queue_bounce_limit(sdev1->request_queue,
+ ATA_DMA_MASK);
+
+ pci_set_dma_mask(pdev, ATA_DMA_MASK);
+ } else {
+ /** This shouldn't fail as it was set to this value before */
+ pci_set_dma_mask(pdev, pp->adma_dma_mask);
+ if (sdev0)
+ blk_queue_bounce_limit(sdev0->request_queue,
+ pp->adma_dma_mask);
+ if (sdev1)
+ blk_queue_bounce_limit(sdev1->request_queue,
+ pp->adma_dma_mask);
+ }
+
blk_queue_segment_boundary(sdev->request_queue, segment_boundary);
blk_queue_max_hw_segments(sdev->request_queue, sg_tablesize);
ata_port_printk(ap, KERN_INFO,
- "bounce limit 0x%llX, segment boundary 0x%lX, hw segs %hu\n",
- (unsigned long long)bounce_limit, segment_boundary, sg_tablesize);
+ "DMA mask 0x%llX, segment boundary 0x%lX, hw segs %hu\n",
+ (unsigned long long)*ap->host->dev->dma_mask,
+ segment_boundary, sg_tablesize);
+
+ spin_unlock_irqrestore(ap->lock, flags);
+
return rc;
}
@@ -1140,10 +1179,20 @@ static int nv_adma_port_start(struct ata_port *ap)
void *mem;
dma_addr_t mem_dma;
void __iomem *mmio;
+ struct pci_dev *pdev = to_pci_dev(dev);
u16 tmp;
VPRINTK("ENTER\n");
+ /* Ensure DMA mask is set to 32-bit before allocating legacy PRD and
+ pad buffers */
+ rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (rc)
+ return rc;
+ rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (rc)
+ return rc;
+
rc = ata_port_start(ap);
if (rc)
return rc;
@@ -1159,6 +1208,15 @@ static int nv_adma_port_start(struct ata_port *ap)
pp->notifier_clear_block = pp->gen_block +
NV_ADMA_NOTIFIER_CLEAR + (4 * ap->port_no);
+ /* Now that the legacy PRD and padding buffer are allocated we can
+ safely raise the DMA mask to allocate the CPB/APRD table.
+ These are allowed to fail since we store the value that ends up
+ being used to set as the bounce limit in slave_config later if
+ needed. */
+ pci_set_dma_mask(pdev, DMA_BIT_MASK(64));
+ pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+ pp->adma_dma_mask = *dev->dma_mask;
+
mem = dmam_alloc_coherent(dev, NV_ADMA_PORT_PRIV_DMA_SZ,
&mem_dma, GFP_KERNEL);
if (!mem)
@@ -2417,12 +2475,6 @@ static int nv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
hpriv->type = type;
host->private_data = hpriv;
- /* set 64bit dma masks, may fail */
- if (type == ADMA) {
- if (pci_set_dma_mask(pdev, DMA_64BIT_MASK) == 0)
- pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
- }
-
/* request and iomap NV_MMIO_BAR */
rc = pcim_iomap_regions(pdev, 1 << NV_MMIO_BAR, DRV_NAME);
if (rc)
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index 3ef072f..30caa03 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -30,8 +30,6 @@
* Hardware documentation available under NDA.
*
*
- * To-do list:
- * - VT6421 PATA support
*
*/
diff --git a/drivers/ide/legacy/ide_platform.c b/drivers/ide/legacy/ide_platform.c
index 26c82ce..688fcae 100644
--- a/drivers/ide/legacy/ide_platform.c
+++ b/drivers/ide/legacy/ide_platform.c
@@ -17,7 +17,7 @@
#include <linux/ide.h>
#include <linux/ioport.h>
#include <linux/module.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/platform_device.h>
#include <linux/io.h>
diff --git a/include/linux/ata_platform.h b/include/linux/ata_platform.h
new file mode 100644
index 0000000..b856a2a
--- /dev/null
+++ b/include/linux/ata_platform.h
@@ -0,0 +1,34 @@
+#ifndef __LINUX_ATA_PLATFORM_H
+#define __LINUX_ATA_PLATFORM_H
+
+struct pata_platform_info {
+ /*
+ * I/O port shift, for platforms with ports that are
+ * constantly spaced and need larger than the 1-byte
+ * spacing used by ata_std_ports().
+ */
+ unsigned int ioport_shift;
+ /*
+ * Indicate platform specific irq types and initial
+ * IRQ flags when call request_irq()
+ */
+ unsigned int irq_flags;
+};
+
+extern int __devinit __pata_platform_probe(struct device *dev,
+ struct resource *io_res,
+ struct resource *ctl_res,
+ struct resource *irq_res,
+ unsigned int ioport_shift,
+ int __pio_mask);
+
+extern int __devexit __pata_platform_remove(struct device *dev);
+
+/*
+ * Marvell SATA private data
+ */
+struct mv_sata_platform_data {
+ int n_ports; /* number of sata ports */
+};
+
+#endif /* __LINUX_ATA_PLATFORM_H */
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 4374c42..bc5a8d0 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -457,7 +457,6 @@ struct ata_queued_cmd {
unsigned long flags; /* ATA_QCFLAG_xxx */
unsigned int tag;
unsigned int n_elem;
- unsigned int n_iter;
unsigned int mapped_n_elem;
int dma_dir;
@@ -1367,7 +1366,6 @@ static inline void ata_qc_reinit(struct ata_queued_cmd *qc)
qc->nbytes = qc->raw_nbytes = qc->curbytes = 0;
qc->n_elem = 0;
qc->mapped_n_elem = 0;
- qc->n_iter = 0;
qc->err_mask = 0;
qc->pad_len = 0;
qc->last_sg = NULL;
diff --git a/include/linux/pata_platform.h b/include/linux/pata_platform.h
deleted file mode 100644
index 6a7a92d..0000000
--- a/include/linux/pata_platform.h
+++ /dev/null
@@ -1,27 +0,0 @@
-#ifndef __LINUX_PATA_PLATFORM_H
-#define __LINUX_PATA_PLATFORM_H
-
-struct pata_platform_info {
- /*
- * I/O port shift, for platforms with ports that are
- * constantly spaced and need larger than the 1-byte
- * spacing used by ata_std_ports().
- */
- unsigned int ioport_shift;
- /*
- * Indicate platform specific irq types and initial
- * IRQ flags when call request_irq()
- */
- unsigned int irq_flags;
-};
-
-extern int __devinit __pata_platform_probe(struct device *dev,
- struct resource *io_res,
- struct resource *ctl_res,
- struct resource *irq_res,
- unsigned int ioport_shift,
- int __pio_mask);
-
-extern int __devexit __pata_platform_remove(struct device *dev);
-
-#endif /* __LINUX_PATA_PLATFORM_H */
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2008-02-01 18:33 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2008-02-01 18:33 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
The PCI change was ack'd by Greg...
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/Kconfig | 2 +-
drivers/ata/ahci.c | 2 +
drivers/ata/ata_piix.c | 10 +-
drivers/ata/pata_bf54x.c | 53 ++---
drivers/ata/pata_sl82c105.c | 33 +++-
drivers/ata/sata_mv.c | 486 +++++++++++++++++++++++++++----------------
drivers/ata/sata_nv.c | 18 +-
drivers/pci/pci.c | 3 +-
8 files changed, 389 insertions(+), 218 deletions(-)
Adrian Bunk (1):
ata_piix.c: make piix_merge_scr() static
Alan Cox (1):
pata_sl82c105: dual channel support
Bryan Wu (1):
Blackfin pata-bf54x driver: fix compiling bug - no ata_port struct in struct ata_device any more
Jason Gaston (2):
ahci: RAID mode SATA patch for Intel ICH10 DeviceID's
ata_piix: IDE mode SATA patch for Intel ICH10 DeviceID's
Mark Lord (13):
sata_mv ncq EH fixes
sata_mv ncq Mask transient IRQs
sata_mv ncq Rename base to port mmio
sata_mv ncq Fix EDMA configuration
sata_mv ncq Add want ncq parameter for EDMA configuration
sata_mv ncq Use hqtag instead of ioid
sata_mv ncq Ignore response status LSB on NCQ
sata_mv ncq Restrict max sectors to 8-bits on GenII NCQ
sata_mv ncq Use DMA memory pools for hardware memory tables
sata_mv ncq Introduce per-tag SG tables
sata_mv ncq Enable NCQ operation
sata_mv ncq Remove post internal cmd op
sata_mv ncq Comments and version bump
Robert Hancock (1):
sata_nv: fix for completion handling
Saeed Bishara (1):
sata_mv: Remove PCI dependency
Sonic Zhang (3):
Blackfin pata-bf54x driver: Remove obsolete PM function
Blackfin pata-bf54x driver: Add debug information
Blackfin pata-bf54x driver: should cover all possible interrupt sources
Tejun Heo (1):
pci: allow multiple calls to pcim_enable_device()
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index ae19c9b..ba8f7f4 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -69,7 +69,7 @@ config ATA_PIIX
config SATA_MV
tristate "Marvell SATA support (HIGHLY EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ depends on EXPERIMENTAL
help
This option enables support for the Marvell Serial ATA family.
Currently supports 88SX[56]0[48][01] chips.
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 6f089b8..27c8d56 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -475,6 +475,8 @@ static const struct pci_device_id ahci_pci_tbl[] = {
{ PCI_VDEVICE(INTEL, 0x294e), board_ahci }, /* ICH9M */
{ PCI_VDEVICE(INTEL, 0x502a), board_ahci }, /* Tolapai */
{ PCI_VDEVICE(INTEL, 0x502b), board_ahci }, /* Tolapai */
+ { PCI_VDEVICE(INTEL, 0x3a05), board_ahci }, /* ICH10 */
+ { PCI_VDEVICE(INTEL, 0x3a25), board_ahci }, /* ICH10 */
/* JMicron 360/1/3/5/6, match class to avoid IDE function */
{ PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index a65c8ae..47892e6 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -267,6 +267,14 @@ static const struct pci_device_id piix_pci_tbl[] = {
{ 0x8086, 0x292e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
/* SATA Controller IDE (Tolapai) */
{ 0x8086, 0x5028, PCI_ANY_ID, PCI_ANY_ID, 0, 0, tolapai_sata_ahci },
+ /* SATA Controller IDE (ICH10) */
+ { 0x8086, 0x3a00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH10) */
+ { 0x8086, 0x3a06, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
+ /* SATA Controller IDE (ICH10) */
+ { 0x8086, 0x3a20, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH10) */
+ { 0x8086, 0x3a26, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
{ } /* terminate list */
};
@@ -1068,7 +1076,7 @@ static void piix_sidpr_write(struct ata_device *dev, unsigned int reg, u32 val)
iowrite32(val, hpriv->sidpr + PIIX_SIDPR_DATA);
}
-u32 piix_merge_scr(u32 val0, u32 val1, const int * const *merge_tbl)
+static u32 piix_merge_scr(u32 val0, u32 val1, const int * const *merge_tbl)
{
u32 val = 0;
int i, mi;
diff --git a/drivers/ata/pata_bf54x.c b/drivers/ata/pata_bf54x.c
index a32e3c4..7f87f10 100644
--- a/drivers/ata/pata_bf54x.c
+++ b/drivers/ata/pata_bf54x.c
@@ -299,7 +299,7 @@ static void bfin_set_piomode(struct ata_port *ap, struct ata_device *adev)
*/
n6 = num_clocks_min(t6min, fsclk);
if (mode >= 0 && mode <= 4 && n6 >= 1) {
- pr_debug("set piomode: mode=%d, fsclk=%ud\n", mode, fsclk);
+ dev_dbg(adev->link->ap->dev, "set piomode: mode=%d, fsclk=%ud\n", mode, fsclk);
/* calculate the timing values for register transfers. */
while (mode > 0 && pio_fsclk[mode] > fsclk)
mode--;
@@ -376,7 +376,7 @@ static void bfin_set_dmamode(struct ata_port *ap, struct ata_device *adev)
mode = adev->dma_mode - XFER_UDMA_0;
if (mode >= 0 && mode <= 5) {
- pr_debug("set udmamode: mode=%d\n", mode);
+ dev_dbg(adev->link->ap->dev, "set udmamode: mode=%d\n", mode);
/* the most restrictive timing value is t6 and tc,
* the DIOW - data hold. If one SCLK pulse is longer
* than this minimum value then register
@@ -433,7 +433,7 @@ static void bfin_set_dmamode(struct ata_port *ap, struct ata_device *adev)
mode = adev->dma_mode - XFER_MW_DMA_0;
if (mode >= 0 && mode <= 2) {
- pr_debug("set mdmamode: mode=%d\n", mode);
+ dev_dbg(adev->link->ap->dev, "set mdmamode: mode=%d\n", mode);
/* the most restrictive timing value is tf, the DMACK to
* read data released. If one SCLK pulse is longer than
* this maximum value then the MDMA mode
@@ -697,7 +697,7 @@ static void bfin_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
write_atapi_register(base, ATA_REG_LBAL, tf->hob_lbal);
write_atapi_register(base, ATA_REG_LBAM, tf->hob_lbam);
write_atapi_register(base, ATA_REG_LBAH, tf->hob_lbah);
- pr_debug("hob: feat 0x%X nsect 0x%X, lba 0x%X "
+ dev_dbg(ap->dev, "hob: feat 0x%X nsect 0x%X, lba 0x%X "
"0x%X 0x%X\n",
tf->hob_feature,
tf->hob_nsect,
@@ -711,7 +711,7 @@ static void bfin_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
write_atapi_register(base, ATA_REG_LBAL, tf->lbal);
write_atapi_register(base, ATA_REG_LBAM, tf->lbam);
write_atapi_register(base, ATA_REG_LBAH, tf->lbah);
- pr_debug("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
+ dev_dbg(ap->dev, "feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
tf->feature,
tf->nsect,
tf->lbal,
@@ -721,7 +721,7 @@ static void bfin_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
if (tf->flags & ATA_TFLAG_DEVICE) {
write_atapi_register(base, ATA_REG_DEVICE, tf->device);
- pr_debug("device 0x%X\n", tf->device);
+ dev_dbg(ap->dev, "device 0x%X\n", tf->device);
}
ata_wait_idle(ap);
@@ -782,7 +782,7 @@ static void bfin_exec_command(struct ata_port *ap,
const struct ata_taskfile *tf)
{
void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
- pr_debug("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
+ dev_dbg(ap->dev, "ata%u: cmd 0x%X\n", ap->print_id, tf->command);
write_atapi_register(base, ATA_REG_CMD, tf->command);
ata_pause(ap);
@@ -834,7 +834,7 @@ static void bfin_bmdma_setup(struct ata_queued_cmd *qc)
struct scatterlist *sg;
unsigned int si;
- pr_debug("in atapi dma setup\n");
+ dev_dbg(qc->ap->dev, "in atapi dma setup\n");
/* Program the ATA_CTRL register with dir */
if (qc->tf.flags & ATA_TFLAG_WRITE) {
/* fill the ATAPI DMA controller */
@@ -870,7 +870,7 @@ static void bfin_bmdma_start(struct ata_queued_cmd *qc)
struct scatterlist *sg;
unsigned int si;
- pr_debug("in atapi dma start\n");
+ dev_dbg(qc->ap->dev, "in atapi dma start\n");
if (!(ap->udma_mask || ap->mwdma_mask))
return;
@@ -888,7 +888,7 @@ static void bfin_bmdma_start(struct ata_queued_cmd *qc)
sg_dma_address(sg) + sg_dma_len(sg));
}
enable_dma(CH_ATAPI_TX);
- pr_debug("enable udma write\n");
+ dev_dbg(qc->ap->dev, "enable udma write\n");
/* Send ATA DMA write command */
bfin_exec_command(ap, &qc->tf);
@@ -898,7 +898,7 @@ static void bfin_bmdma_start(struct ata_queued_cmd *qc)
| XFER_DIR));
} else {
enable_dma(CH_ATAPI_RX);
- pr_debug("enable udma read\n");
+ dev_dbg(qc->ap->dev, "enable udma read\n");
/* Send ATA DMA read command */
bfin_exec_command(ap, &qc->tf);
@@ -936,7 +936,7 @@ static void bfin_bmdma_stop(struct ata_queued_cmd *qc)
struct scatterlist *sg;
unsigned int si;
- pr_debug("in atapi dma stop\n");
+ dev_dbg(qc->ap->dev, "in atapi dma stop\n");
if (!(ap->udma_mask || ap->mwdma_mask))
return;
@@ -1147,15 +1147,15 @@ static unsigned char bfin_bmdma_status(struct ata_port *ap)
void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
unsigned short int_status = ATAPI_GET_INT_STATUS(base);
- if (ATAPI_GET_STATUS(base) & (MULTI_XFER_ON|ULTRA_XFER_ON)) {
+ if (ATAPI_GET_STATUS(base) & (MULTI_XFER_ON|ULTRA_XFER_ON))
host_stat |= ATA_DMA_ACTIVE;
- }
- if (int_status & (MULTI_DONE_INT|UDMAIN_DONE_INT|UDMAOUT_DONE_INT)) {
+ if (int_status & (MULTI_DONE_INT|UDMAIN_DONE_INT|UDMAOUT_DONE_INT|
+ ATAPI_DEV_INT))
host_stat |= ATA_DMA_INTR;
- }
- if (int_status & (MULTI_TERM_INT|UDMAIN_TERM_INT|UDMAOUT_TERM_INT)) {
- host_stat |= ATA_DMA_ERR;
- }
+ if (int_status & (MULTI_TERM_INT|UDMAIN_TERM_INT|UDMAOUT_TERM_INT))
+ host_stat |= ATA_DMA_ERR|ATA_DMA_INTR;
+
+ dev_dbg(ap->dev, "ATAPI: host_stat=0x%x\n", host_stat);
return host_stat;
}
@@ -1213,8 +1213,7 @@ static void bfin_irq_clear(struct ata_port *ap)
{
void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
- pr_debug("in atapi irq clear\n");
-
+ dev_dbg(ap->dev, "in atapi irq clear\n");
ATAPI_SET_INT_STATUS(base, ATAPI_GET_INT_STATUS(base)|ATAPI_DEV_INT
| MULTI_DONE_INT | UDMAIN_DONE_INT | UDMAOUT_DONE_INT
| MULTI_TERM_INT | UDMAIN_TERM_INT | UDMAOUT_TERM_INT);
@@ -1232,7 +1231,7 @@ static unsigned char bfin_irq_on(struct ata_port *ap)
void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
u8 tmp;
- pr_debug("in atapi irq on\n");
+ dev_dbg(ap->dev, "in atapi irq on\n");
ap->ctl &= ~ATA_NIEN;
ap->last_ctl = ap->ctl;
@@ -1255,7 +1254,7 @@ static void bfin_bmdma_freeze(struct ata_port *ap)
{
void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
- pr_debug("in atapi dma freeze\n");
+ dev_dbg(ap->dev, "in atapi dma freeze\n");
ap->ctl |= ATA_NIEN;
ap->last_ctl = ap->ctl;
@@ -1328,7 +1327,7 @@ static void bfin_error_handler(struct ata_port *ap)
static void bfin_port_stop(struct ata_port *ap)
{
- pr_debug("in atapi port stop\n");
+ dev_dbg(ap->dev, "in atapi port stop\n");
if (ap->udma_mask != 0 || ap->mwdma_mask != 0) {
free_dma(CH_ATAPI_RX);
free_dma(CH_ATAPI_TX);
@@ -1337,7 +1336,7 @@ static void bfin_port_stop(struct ata_port *ap)
static int bfin_port_start(struct ata_port *ap)
{
- pr_debug("in atapi port start\n");
+ dev_dbg(ap->dev, "in atapi port start\n");
if (!(ap->udma_mask || ap->mwdma_mask))
return 0;
@@ -1373,10 +1372,6 @@ static struct scsi_host_template bfin_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static const struct ata_port_operations bfin_pata_ops = {
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index 1388cef..81ef207 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -26,7 +26,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_sl82c105"
-#define DRV_VERSION "0.3.2"
+#define DRV_VERSION "0.3.3"
enum {
/*
@@ -206,6 +206,34 @@ static void sl82c105_bmdma_stop(struct ata_queued_cmd *qc)
sl82c105_set_piomode(ap, qc->dev);
}
+/**
+ * sl82c105_qc_defer - implement serialization
+ * @qc: command
+ *
+ * We must issue one command per host not per channel because
+ * of the reset bug.
+ *
+ * Q: is the scsi host lock sufficient ?
+ */
+
+static int sl82c105_qc_defer(struct ata_queued_cmd *qc)
+{
+ struct ata_host *host = qc->ap->host;
+ struct ata_port *alt = host->ports[1 ^ qc->ap->port_no];
+ int rc;
+
+ /* First apply the usual rules */
+ rc = ata_std_qc_defer(qc);
+ if (rc != 0)
+ return rc;
+
+ /* Now apply serialization rules. Only allow a command if the
+ other channel state machine is idle */
+ if (alt && alt->qc_active)
+ return ATA_DEFER_PORT;
+ return 0;
+}
+
static struct scsi_host_template sl82c105_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
@@ -245,6 +273,7 @@ static struct ata_port_operations sl82c105_port_ops = {
.bmdma_stop = sl82c105_bmdma_stop,
.bmdma_status = ata_bmdma_status,
+ .qc_defer = sl82c105_qc_defer,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
@@ -312,7 +341,7 @@ static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id
};
/* for now use only the first port */
const struct ata_port_info *ppi[] = { &info_early,
- &ata_dummy_port_info };
+ NULL };
u32 val;
int rev;
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 7e72463..3c1b5c9 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -29,7 +29,13 @@
I distinctly remember a couple workarounds (one related to PCI-X)
are still needed.
- 4) Add NCQ support (easy to intermediate, once new-EH support appears)
+ 2) Improve/fix IRQ and error handling sequences.
+
+ 3) ATAPI support (Marvell claims the 60xx/70xx chips can do it).
+
+ 4) Think about TCQ support here, and for libata in general
+ with controllers that suppport it via host-queuing hardware
+ (a software-only implementation could be a nightmare).
5) Investigate problems with PCI Message Signalled Interrupts (MSI).
@@ -53,8 +59,6 @@
Target mode, for those without docs, is the ability to directly
connect two SATA controllers.
- 13) Verify that 7042 is fully supported. I only have a 6042.
-
*/
@@ -73,7 +77,7 @@
#include <linux/libata.h>
#define DRV_NAME "sata_mv"
-#define DRV_VERSION "1.01"
+#define DRV_VERSION "1.20"
enum {
/* BAR's are enumerated in terms of pci_resource_start() terms */
@@ -107,14 +111,12 @@ enum {
/* CRQB needs alignment on a 1KB boundary. Size == 1KB
* CRPB needs alignment on a 256B boundary. Size == 256B
- * SG count of 176 leads to MV_PORT_PRIV_DMA_SZ == 4KB
* ePRD (SG) entries need alignment on a 16B boundary. Size == 16B
*/
MV_CRQB_Q_SZ = (32 * MV_MAX_Q_DEPTH),
MV_CRPB_Q_SZ = (8 * MV_MAX_Q_DEPTH),
- MV_MAX_SG_CT = 176,
+ MV_MAX_SG_CT = 256,
MV_SG_TBL_SZ = (16 * MV_MAX_SG_CT),
- MV_PORT_PRIV_DMA_SZ = (MV_CRQB_Q_SZ + MV_CRPB_Q_SZ + MV_SG_TBL_SZ),
MV_PORTS_PER_HC = 4,
/* == (port / MV_PORTS_PER_HC) to determine HC from 0-7 port */
@@ -125,6 +127,9 @@ enum {
/* Host Flags */
MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */
MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */
+ /* SoC integrated controllers, no PCI interface */
+ MV_FLAG_SOC = (1 << 28),
+
MV_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI |
ATA_FLAG_PIO_POLLING,
@@ -170,7 +175,7 @@ enum {
PCIE_IRQ_CAUSE_OFS = 0x1900,
PCIE_IRQ_MASK_OFS = 0x1910,
- PCIE_UNMASK_ALL_IRQS = 0x70a, /* assorted bits */
+ PCIE_UNMASK_ALL_IRQS = 0x40a, /* assorted bits */
HC_MAIN_IRQ_CAUSE_OFS = 0x1d60,
HC_MAIN_IRQ_MASK_OFS = 0x1d64,
@@ -210,6 +215,7 @@ enum {
/* SATA registers */
SATA_STATUS_OFS = 0x300, /* ctrl, err regs follow status */
SATA_ACTIVE_OFS = 0x350,
+ SATA_FIS_IRQ_CAUSE_OFS = 0x364,
PHY_MODE3 = 0x310,
PHY_MODE4 = 0x314,
PHY_MODE2 = 0x330,
@@ -222,11 +228,11 @@ enum {
/* Port registers */
EDMA_CFG_OFS = 0,
- EDMA_CFG_Q_DEPTH = 0, /* queueing disabled */
- EDMA_CFG_NCQ = (1 << 5),
- EDMA_CFG_NCQ_GO_ON_ERR = (1 << 14), /* continue on error */
- EDMA_CFG_RD_BRST_EXT = (1 << 11), /* read burst 512B */
- EDMA_CFG_WR_BUFF_LEN = (1 << 13), /* write buffer 512B */
+ EDMA_CFG_Q_DEPTH = 0x1f, /* max device queue depth */
+ EDMA_CFG_NCQ = (1 << 5), /* for R/W FPDMA queued */
+ EDMA_CFG_NCQ_GO_ON_ERR = (1 << 14), /* continue on error */
+ EDMA_CFG_RD_BRST_EXT = (1 << 11), /* read burst 512B */
+ EDMA_CFG_WR_BUFF_LEN = (1 << 13), /* write buffer 512B */
EDMA_ERR_IRQ_CAUSE_OFS = 0x8,
EDMA_ERR_IRQ_MASK_OFS = 0xc,
@@ -244,14 +250,33 @@ enum {
EDMA_ERR_CRPB_PAR = (1 << 10), /* CRPB parity error */
EDMA_ERR_INTRL_PAR = (1 << 11), /* internal parity error */
EDMA_ERR_IORDY = (1 << 12), /* IORdy timeout */
+
EDMA_ERR_LNK_CTRL_RX = (0xf << 13), /* link ctrl rx error */
- EDMA_ERR_LNK_CTRL_RX_2 = (1 << 15),
+ EDMA_ERR_LNK_CTRL_RX_0 = (1 << 13), /* transient: CRC err */
+ EDMA_ERR_LNK_CTRL_RX_1 = (1 << 14), /* transient: FIFO err */
+ EDMA_ERR_LNK_CTRL_RX_2 = (1 << 15), /* fatal: caught SYNC */
+ EDMA_ERR_LNK_CTRL_RX_3 = (1 << 16), /* transient: FIS rx err */
+
EDMA_ERR_LNK_DATA_RX = (0xf << 17), /* link data rx error */
+
EDMA_ERR_LNK_CTRL_TX = (0x1f << 21), /* link ctrl tx error */
+ EDMA_ERR_LNK_CTRL_TX_0 = (1 << 21), /* transient: CRC err */
+ EDMA_ERR_LNK_CTRL_TX_1 = (1 << 22), /* transient: FIFO err */
+ EDMA_ERR_LNK_CTRL_TX_2 = (1 << 23), /* transient: caught SYNC */
+ EDMA_ERR_LNK_CTRL_TX_3 = (1 << 24), /* transient: caught DMAT */
+ EDMA_ERR_LNK_CTRL_TX_4 = (1 << 25), /* transient: FIS collision */
+
EDMA_ERR_LNK_DATA_TX = (0x1f << 26), /* link data tx error */
+
EDMA_ERR_TRANS_PROTO = (1 << 31), /* transport protocol error */
EDMA_ERR_OVERRUN_5 = (1 << 5),
EDMA_ERR_UNDERRUN_5 = (1 << 6),
+
+ EDMA_ERR_IRQ_TRANSIENT = EDMA_ERR_LNK_CTRL_RX_0 |
+ EDMA_ERR_LNK_CTRL_RX_1 |
+ EDMA_ERR_LNK_CTRL_RX_3 |
+ EDMA_ERR_LNK_CTRL_TX,
+
EDMA_EH_FREEZE = EDMA_ERR_D_PAR |
EDMA_ERR_PRD_PAR |
EDMA_ERR_DEV_DCON |
@@ -311,12 +336,14 @@ enum {
/* Port private flags (pp_flags) */
MV_PP_FLAG_EDMA_EN = (1 << 0), /* is EDMA engine enabled? */
+ MV_PP_FLAG_NCQ_EN = (1 << 1), /* is EDMA set up for NCQ? */
MV_PP_FLAG_HAD_A_RESET = (1 << 2), /* 1st hard reset complete? */
};
#define IS_GEN_I(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_I)
#define IS_GEN_II(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_II)
#define IS_GEN_IIE(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_IIE)
+#define HAS_PCI(host) (!((host)->ports[0]->flags & MV_FLAG_SOC))
enum {
/* DMA boundary 0xffff is required by the s/g splitting
@@ -379,8 +406,8 @@ struct mv_port_priv {
dma_addr_t crqb_dma;
struct mv_crpb *crpb;
dma_addr_t crpb_dma;
- struct mv_sg *sg_tbl;
- dma_addr_t sg_tbl_dma;
+ struct mv_sg *sg_tbl[MV_MAX_Q_DEPTH];
+ dma_addr_t sg_tbl_dma[MV_MAX_Q_DEPTH];
unsigned int req_idx;
unsigned int resp_idx;
@@ -400,6 +427,14 @@ struct mv_host_priv {
u32 irq_cause_ofs;
u32 irq_mask_ofs;
u32 unmask_all_irqs;
+ /*
+ * These consistent DMA memory pools give us guaranteed
+ * alignment for hardware-accessed data structures,
+ * and less memory waste in accomplishing the alignment.
+ */
+ struct dma_pool *crqb_pool;
+ struct dma_pool *crpb_pool;
+ struct dma_pool *sg_tbl_pool;
};
struct mv_hw_ops {
@@ -411,7 +446,7 @@ struct mv_hw_ops {
int (*reset_hc)(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int n_hc);
void (*reset_flash)(struct mv_host_priv *hpriv, void __iomem *mmio);
- void (*reset_bus)(struct pci_dev *pdev, void __iomem *mmio);
+ void (*reset_bus)(struct ata_host *host, void __iomem *mmio);
};
static void mv_irq_clear(struct ata_port *ap);
@@ -425,10 +460,9 @@ static void mv_qc_prep(struct ata_queued_cmd *qc);
static void mv_qc_prep_iie(struct ata_queued_cmd *qc);
static unsigned int mv_qc_issue(struct ata_queued_cmd *qc);
static void mv_error_handler(struct ata_port *ap);
-static void mv_post_int_cmd(struct ata_queued_cmd *qc);
static void mv_eh_freeze(struct ata_port *ap);
static void mv_eh_thaw(struct ata_port *ap);
-static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
+static void mv6_dev_config(struct ata_device *dev);
static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int port);
@@ -438,7 +472,7 @@ static void mv5_read_preamp(struct mv_host_priv *hpriv, int idx,
static int mv5_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int n_hc);
static void mv5_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio);
-static void mv5_reset_bus(struct pci_dev *pdev, void __iomem *mmio);
+static void mv5_reset_bus(struct ata_host *host, void __iomem *mmio);
static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int port);
@@ -448,10 +482,17 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx,
static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int n_hc);
static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio);
-static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio);
+static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio);
static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int port_no);
+static void mv_edma_cfg(struct mv_port_priv *pp, struct mv_host_priv *hpriv,
+ void __iomem *port_mmio, int want_ncq);
+static int __mv_stop_dma(struct ata_port *ap);
+/* .sg_tablesize is (MV_MAX_SG_CT / 2) in the structures below
+ * because we have to allow room for worst case splitting of
+ * PRDs for 64K boundaries in mv_fill_sg().
+ */
static struct scsi_host_template mv5_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
@@ -475,7 +516,8 @@ static struct scsi_host_template mv6_sht = {
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
- .can_queue = ATA_DEF_QUEUE,
+ .change_queue_depth = ata_scsi_change_queue_depth,
+ .can_queue = MV_MAX_Q_DEPTH - 1,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = MV_MAX_SG_CT / 2,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
@@ -505,7 +547,6 @@ static const struct ata_port_operations mv5_ops = {
.irq_on = ata_irq_on,
.error_handler = mv_error_handler,
- .post_internal_cmd = mv_post_int_cmd,
.freeze = mv_eh_freeze,
.thaw = mv_eh_thaw,
@@ -517,6 +558,7 @@ static const struct ata_port_operations mv5_ops = {
};
static const struct ata_port_operations mv6_ops = {
+ .dev_config = mv6_dev_config,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
@@ -533,9 +575,9 @@ static const struct ata_port_operations mv6_ops = {
.irq_on = ata_irq_on,
.error_handler = mv_error_handler,
- .post_internal_cmd = mv_post_int_cmd,
.freeze = mv_eh_freeze,
.thaw = mv_eh_thaw,
+ .qc_defer = ata_std_qc_defer,
.scr_read = mv_scr_read,
.scr_write = mv_scr_write,
@@ -561,9 +603,9 @@ static const struct ata_port_operations mv_iie_ops = {
.irq_on = ata_irq_on,
.error_handler = mv_error_handler,
- .post_internal_cmd = mv_post_int_cmd,
.freeze = mv_eh_freeze,
.thaw = mv_eh_thaw,
+ .qc_defer = ata_std_qc_defer,
.scr_read = mv_scr_read,
.scr_write = mv_scr_write,
@@ -592,26 +634,29 @@ static const struct ata_port_info mv_port_info[] = {
.port_ops = &mv5_ops,
},
{ /* chip_604x */
- .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS,
+ .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
+ ATA_FLAG_NCQ,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv6_ops,
},
{ /* chip_608x */
.flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- MV_FLAG_DUAL_HC,
+ ATA_FLAG_NCQ | MV_FLAG_DUAL_HC,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv6_ops,
},
{ /* chip_6042 */
- .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS,
+ .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
+ ATA_FLAG_NCQ,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
{ /* chip_7042 */
- .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS,
+ .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
+ ATA_FLAG_NCQ,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
@@ -648,13 +693,6 @@ static const struct pci_device_id mv_pci_tbl[] = {
{ } /* terminate list */
};
-static struct pci_driver mv_pci_driver = {
- .name = DRV_NAME,
- .id_table = mv_pci_tbl,
- .probe = mv_init_one,
- .remove = ata_pci_remove_one,
-};
-
static const struct mv_hw_ops mv5xxx_ops = {
.phy_errata = mv5_phy_errata,
.enable_leds = mv5_enable_leds,
@@ -674,45 +712,6 @@ static const struct mv_hw_ops mv6xxx_ops = {
};
/*
- * module options
- */
-static int msi; /* Use PCI msi; either zero (off, default) or non-zero */
-
-
-/* move to PCI layer or libata core? */
-static int pci_go_64(struct pci_dev *pdev)
-{
- int rc;
-
- if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
- rc = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
- if (rc) {
- rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
- if (rc) {
- dev_printk(KERN_ERR, &pdev->dev,
- "64-bit DMA enable failed\n");
- return rc;
- }
- }
- } else {
- rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
- if (rc) {
- dev_printk(KERN_ERR, &pdev->dev,
- "32-bit DMA enable failed\n");
- return rc;
- }
- rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
- if (rc) {
- dev_printk(KERN_ERR, &pdev->dev,
- "32-bit consistent DMA enable failed\n");
- return rc;
- }
- }
-
- return rc;
-}
-
-/*
* Functions
*/
@@ -815,19 +814,46 @@ static void mv_set_edma_ptrs(void __iomem *port_mmio,
* LOCKING:
* Inherited from caller.
*/
-static void mv_start_dma(void __iomem *base, struct mv_host_priv *hpriv,
- struct mv_port_priv *pp)
+static void mv_start_dma(struct ata_port *ap, void __iomem *port_mmio,
+ struct mv_port_priv *pp, u8 protocol)
{
+ int want_ncq = (protocol == ATA_PROT_NCQ);
+
+ if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) {
+ int using_ncq = ((pp->pp_flags & MV_PP_FLAG_NCQ_EN) != 0);
+ if (want_ncq != using_ncq)
+ __mv_stop_dma(ap);
+ }
if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN)) {
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ int hard_port = mv_hardport_from_port(ap->port_no);
+ void __iomem *hc_mmio = mv_hc_base_from_port(
+ ap->host->iomap[MV_PRIMARY_BAR], hard_port);
+ u32 hc_irq_cause, ipending;
+
/* clear EDMA event indicators, if any */
- writelfl(0, base + EDMA_ERR_IRQ_CAUSE_OFS);
+ writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+
+ /* clear EDMA interrupt indicator, if any */
+ hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
+ ipending = (DEV_IRQ << hard_port) |
+ (CRPB_DMA_DONE << hard_port);
+ if (hc_irq_cause & ipending) {
+ writelfl(hc_irq_cause & ~ipending,
+ hc_mmio + HC_IRQ_CAUSE_OFS);
+ }
+
+ mv_edma_cfg(pp, hpriv, port_mmio, want_ncq);
+
+ /* clear FIS IRQ Cause */
+ writelfl(0, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
- mv_set_edma_ptrs(base, hpriv, pp);
+ mv_set_edma_ptrs(port_mmio, hpriv, pp);
- writelfl(EDMA_EN, base + EDMA_CMD_OFS);
+ writelfl(EDMA_EN, port_mmio + EDMA_CMD_OFS);
pp->pp_flags |= MV_PP_FLAG_EDMA_EN;
}
- WARN_ON(!(EDMA_EN & readl(base + EDMA_CMD_OFS)));
+ WARN_ON(!(EDMA_EN & readl(port_mmio + EDMA_CMD_OFS)));
}
/**
@@ -1003,38 +1029,76 @@ static int mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
return -EINVAL;
}
-static void mv_edma_cfg(struct ata_port *ap, struct mv_host_priv *hpriv,
- void __iomem *port_mmio)
+static void mv6_dev_config(struct ata_device *adev)
{
- u32 cfg = readl(port_mmio + EDMA_CFG_OFS);
+ /*
+ * We don't have hob_nsect when doing NCQ commands on Gen-II.
+ * See mv_qc_prep() for more info.
+ */
+ if (adev->flags & ATA_DFLAG_NCQ)
+ if (adev->max_sectors > ATA_MAX_SECTORS)
+ adev->max_sectors = ATA_MAX_SECTORS;
+}
+
+static void mv_edma_cfg(struct mv_port_priv *pp, struct mv_host_priv *hpriv,
+ void __iomem *port_mmio, int want_ncq)
+{
+ u32 cfg;
/* set up non-NCQ EDMA configuration */
- cfg &= ~(1 << 9); /* disable eQue */
+ cfg = EDMA_CFG_Q_DEPTH; /* always 0x1f for *all* chips */
- if (IS_GEN_I(hpriv)) {
- cfg &= ~0x1f; /* clear queue depth */
+ if (IS_GEN_I(hpriv))
cfg |= (1 << 8); /* enab config burst size mask */
- }
- else if (IS_GEN_II(hpriv)) {
- cfg &= ~0x1f; /* clear queue depth */
+ else if (IS_GEN_II(hpriv))
cfg |= EDMA_CFG_RD_BRST_EXT | EDMA_CFG_WR_BUFF_LEN;
- cfg &= ~(EDMA_CFG_NCQ | EDMA_CFG_NCQ_GO_ON_ERR); /* clear NCQ */
- }
else if (IS_GEN_IIE(hpriv)) {
cfg |= (1 << 23); /* do not mask PM field in rx'd FIS */
cfg |= (1 << 22); /* enab 4-entry host queue cache */
- cfg &= ~(1 << 19); /* dis 128-entry queue (for now?) */
cfg |= (1 << 18); /* enab early completion */
cfg |= (1 << 17); /* enab cut-through (dis stor&forwrd) */
- cfg &= ~(1 << 16); /* dis FIS-based switching (for now) */
- cfg &= ~(EDMA_CFG_NCQ); /* clear NCQ */
}
+ if (want_ncq) {
+ cfg |= EDMA_CFG_NCQ;
+ pp->pp_flags |= MV_PP_FLAG_NCQ_EN;
+ } else
+ pp->pp_flags &= ~MV_PP_FLAG_NCQ_EN;
+
writelfl(cfg, port_mmio + EDMA_CFG_OFS);
}
+static void mv_port_free_dma_mem(struct ata_port *ap)
+{
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ struct mv_port_priv *pp = ap->private_data;
+ int tag;
+
+ if (pp->crqb) {
+ dma_pool_free(hpriv->crqb_pool, pp->crqb, pp->crqb_dma);
+ pp->crqb = NULL;
+ }
+ if (pp->crpb) {
+ dma_pool_free(hpriv->crpb_pool, pp->crpb, pp->crpb_dma);
+ pp->crpb = NULL;
+ }
+ /*
+ * For GEN_I, there's no NCQ, so we have only a single sg_tbl.
+ * For later hardware, we have one unique sg_tbl per NCQ tag.
+ */
+ for (tag = 0; tag < MV_MAX_Q_DEPTH; ++tag) {
+ if (pp->sg_tbl[tag]) {
+ if (tag == 0 || !IS_GEN_I(hpriv))
+ dma_pool_free(hpriv->sg_tbl_pool,
+ pp->sg_tbl[tag],
+ pp->sg_tbl_dma[tag]);
+ pp->sg_tbl[tag] = NULL;
+ }
+ }
+}
+
/**
* mv_port_start - Port specific init/start routine.
* @ap: ATA channel to manipulate
@@ -1051,51 +1115,47 @@ static int mv_port_start(struct ata_port *ap)
struct mv_host_priv *hpriv = ap->host->private_data;
struct mv_port_priv *pp;
void __iomem *port_mmio = mv_ap_base(ap);
- void *mem;
- dma_addr_t mem_dma;
unsigned long flags;
- int rc;
+ int tag, rc;
pp = devm_kzalloc(dev, sizeof(*pp), GFP_KERNEL);
if (!pp)
return -ENOMEM;
-
- mem = dmam_alloc_coherent(dev, MV_PORT_PRIV_DMA_SZ, &mem_dma,
- GFP_KERNEL);
- if (!mem)
- return -ENOMEM;
- memset(mem, 0, MV_PORT_PRIV_DMA_SZ);
+ ap->private_data = pp;
rc = ata_pad_alloc(ap, dev);
if (rc)
return rc;
- /* First item in chunk of DMA memory:
- * 32-slot command request table (CRQB), 32 bytes each in size
- */
- pp->crqb = mem;
- pp->crqb_dma = mem_dma;
- mem += MV_CRQB_Q_SZ;
- mem_dma += MV_CRQB_Q_SZ;
+ pp->crqb = dma_pool_alloc(hpriv->crqb_pool, GFP_KERNEL, &pp->crqb_dma);
+ if (!pp->crqb)
+ return -ENOMEM;
+ memset(pp->crqb, 0, MV_CRQB_Q_SZ);
- /* Second item:
- * 32-slot command response table (CRPB), 8 bytes each in size
- */
- pp->crpb = mem;
- pp->crpb_dma = mem_dma;
- mem += MV_CRPB_Q_SZ;
- mem_dma += MV_CRPB_Q_SZ;
+ pp->crpb = dma_pool_alloc(hpriv->crpb_pool, GFP_KERNEL, &pp->crpb_dma);
+ if (!pp->crpb)
+ goto out_port_free_dma_mem;
+ memset(pp->crpb, 0, MV_CRPB_Q_SZ);
- /* Third item:
- * Table of scatter-gather descriptors (ePRD), 16 bytes each
+ /*
+ * For GEN_I, there's no NCQ, so we only allocate a single sg_tbl.
+ * For later hardware, we need one unique sg_tbl per NCQ tag.
*/
- pp->sg_tbl = mem;
- pp->sg_tbl_dma = mem_dma;
+ for (tag = 0; tag < MV_MAX_Q_DEPTH; ++tag) {
+ if (tag == 0 || !IS_GEN_I(hpriv)) {
+ pp->sg_tbl[tag] = dma_pool_alloc(hpriv->sg_tbl_pool,
+ GFP_KERNEL, &pp->sg_tbl_dma[tag]);
+ if (!pp->sg_tbl[tag])
+ goto out_port_free_dma_mem;
+ } else {
+ pp->sg_tbl[tag] = pp->sg_tbl[0];
+ pp->sg_tbl_dma[tag] = pp->sg_tbl_dma[0];
+ }
+ }
spin_lock_irqsave(&ap->host->lock, flags);
- mv_edma_cfg(ap, hpriv, port_mmio);
-
+ mv_edma_cfg(pp, hpriv, port_mmio, 0);
mv_set_edma_ptrs(port_mmio, hpriv, pp);
spin_unlock_irqrestore(&ap->host->lock, flags);
@@ -1104,8 +1164,11 @@ static int mv_port_start(struct ata_port *ap)
* we'll be unable to send non-data, PIO, etc due to restricted access
* to shadow regs.
*/
- ap->private_data = pp;
return 0;
+
+out_port_free_dma_mem:
+ mv_port_free_dma_mem(ap);
+ return -ENOMEM;
}
/**
@@ -1120,6 +1183,7 @@ static int mv_port_start(struct ata_port *ap)
static void mv_port_stop(struct ata_port *ap)
{
mv_stop_dma(ap);
+ mv_port_free_dma_mem(ap);
}
/**
@@ -1138,7 +1202,7 @@ static void mv_fill_sg(struct ata_queued_cmd *qc)
struct mv_sg *mv_sg, *last_sg = NULL;
unsigned int si;
- mv_sg = pp->sg_tbl;
+ mv_sg = pp->sg_tbl[qc->tag];
for_each_sg(qc->sg, sg, qc->n_elem, si) {
dma_addr_t addr = sg_dma_address(sg);
u32 sg_len = sg_dma_len(sg);
@@ -1194,7 +1258,8 @@ static void mv_qc_prep(struct ata_queued_cmd *qc)
u16 flags = 0;
unsigned in_index;
- if (qc->tf.protocol != ATA_PROT_DMA)
+ if ((qc->tf.protocol != ATA_PROT_DMA) &&
+ (qc->tf.protocol != ATA_PROT_NCQ))
return;
/* Fill in command request block
@@ -1203,15 +1268,14 @@ static void mv_qc_prep(struct ata_queued_cmd *qc)
flags |= CRQB_FLAG_READ;
WARN_ON(MV_MAX_Q_DEPTH <= qc->tag);
flags |= qc->tag << CRQB_TAG_SHIFT;
- flags |= qc->tag << CRQB_IOID_SHIFT; /* 50xx appears to ignore this*/
/* get current queue index from software */
in_index = pp->req_idx & MV_MAX_Q_DEPTH_MASK;
pp->crqb[in_index].sg_addr =
- cpu_to_le32(pp->sg_tbl_dma & 0xffffffff);
+ cpu_to_le32(pp->sg_tbl_dma[qc->tag] & 0xffffffff);
pp->crqb[in_index].sg_addr_hi =
- cpu_to_le32((pp->sg_tbl_dma >> 16) >> 16);
+ cpu_to_le32((pp->sg_tbl_dma[qc->tag] >> 16) >> 16);
pp->crqb[in_index].ctrl_flags = cpu_to_le16(flags);
cw = &pp->crqb[in_index].ata_cmd[0];
@@ -1231,13 +1295,11 @@ static void mv_qc_prep(struct ata_queued_cmd *qc)
case ATA_CMD_WRITE_FUA_EXT:
mv_crqb_pack_cmd(cw++, tf->hob_nsect, ATA_REG_NSECT, 0);
break;
-#ifdef LIBATA_NCQ /* FIXME: remove this line when NCQ added */
case ATA_CMD_FPDMA_READ:
case ATA_CMD_FPDMA_WRITE:
mv_crqb_pack_cmd(cw++, tf->hob_feature, ATA_REG_FEATURE, 0);
mv_crqb_pack_cmd(cw++, tf->feature, ATA_REG_FEATURE, 0);
break;
-#endif /* FIXME: remove this line when NCQ added */
default:
/* The only other commands EDMA supports in non-queued and
* non-NCQ mode are: [RW] STREAM DMA and W DMA FUA EXT, none
@@ -1286,7 +1348,8 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc)
unsigned in_index;
u32 flags = 0;
- if (qc->tf.protocol != ATA_PROT_DMA)
+ if ((qc->tf.protocol != ATA_PROT_DMA) &&
+ (qc->tf.protocol != ATA_PROT_NCQ))
return;
/* Fill in Gen IIE command request block
@@ -1296,15 +1359,14 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc)
WARN_ON(MV_MAX_Q_DEPTH <= qc->tag);
flags |= qc->tag << CRQB_TAG_SHIFT;
- flags |= qc->tag << CRQB_IOID_SHIFT; /* "I/O Id" is -really-
- what we use as our tag */
+ flags |= qc->tag << CRQB_HOSTQ_SHIFT;
/* get current queue index from software */
in_index = pp->req_idx & MV_MAX_Q_DEPTH_MASK;
crqb = (struct mv_crqb_iie *) &pp->crqb[in_index];
- crqb->addr = cpu_to_le32(pp->sg_tbl_dma & 0xffffffff);
- crqb->addr_hi = cpu_to_le32((pp->sg_tbl_dma >> 16) >> 16);
+ crqb->addr = cpu_to_le32(pp->sg_tbl_dma[qc->tag] & 0xffffffff);
+ crqb->addr_hi = cpu_to_le32((pp->sg_tbl_dma[qc->tag] >> 16) >> 16);
crqb->flags = cpu_to_le32(flags);
tf = &qc->tf;
@@ -1351,10 +1413,10 @@ static unsigned int mv_qc_issue(struct ata_queued_cmd *qc)
struct ata_port *ap = qc->ap;
void __iomem *port_mmio = mv_ap_base(ap);
struct mv_port_priv *pp = ap->private_data;
- struct mv_host_priv *hpriv = ap->host->private_data;
u32 in_index;
- if (qc->tf.protocol != ATA_PROT_DMA) {
+ if ((qc->tf.protocol != ATA_PROT_DMA) &&
+ (qc->tf.protocol != ATA_PROT_NCQ)) {
/* We're about to send a non-EDMA capable command to the
* port. Turn off EDMA so there won't be problems accessing
* shadow block, etc registers.
@@ -1363,13 +1425,7 @@ static unsigned int mv_qc_issue(struct ata_queued_cmd *qc)
return ata_qc_issue_prot(qc);
}
- mv_start_dma(port_mmio, hpriv, pp);
-
- in_index = pp->req_idx & MV_MAX_Q_DEPTH_MASK;
-
- /* until we do queuing, the queue should be empty at this point */
- WARN_ON(in_index != ((readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS)
- >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK));
+ mv_start_dma(ap, port_mmio, pp, qc->tf.protocol);
pp->req_idx++;
@@ -1437,6 +1493,7 @@ static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
ata_ehi_hotplugged(ehi);
ata_ehi_push_desc(ehi, edma_err_cause & EDMA_ERR_DEV_DCON ?
"dev disconnect" : "dev connect");
+ action |= ATA_EH_HARDRESET;
}
if (IS_GEN_I(hpriv)) {
@@ -1465,7 +1522,7 @@ static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
}
/* Clear EDMA now that SERR cleanup done */
- writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+ writelfl(~edma_err_cause, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
if (!err_mask) {
err_mask = AC_ERR_OTHER;
@@ -1538,23 +1595,17 @@ static void mv_intr_edma(struct ata_port *ap)
* support for queueing. this works transparently for
* queued and non-queued modes.
*/
- else if (IS_GEN_II(hpriv))
- tag = (le16_to_cpu(pp->crpb[out_index].id)
- >> CRPB_IOID_SHIFT_6) & 0x3f;
-
- else /* IS_GEN_IIE */
- tag = (le16_to_cpu(pp->crpb[out_index].id)
- >> CRPB_IOID_SHIFT_7) & 0x3f;
+ else
+ tag = le16_to_cpu(pp->crpb[out_index].id) & 0x1f;
qc = ata_qc_from_tag(ap, tag);
- /* lower 8 bits of status are EDMA_ERR_IRQ_CAUSE_OFS
- * bits (WARNING: might not necessarily be associated
- * with this command), which -should- be clear
- * if all is well
+ /* For non-NCQ mode, the lower 8 bits of status
+ * are from EDMA_ERR_IRQ_CAUSE_OFS,
+ * which should be zero if all went well.
*/
status = le16_to_cpu(pp->crpb[out_index].flags);
- if (unlikely(status & 0xff)) {
+ if ((status & 0xff) && !(pp->pp_flags & MV_PP_FLAG_NCQ_EN)) {
mv_err_intr(ap, qc);
return;
}
@@ -1715,20 +1766,21 @@ static irqreturn_t mv_interrupt(int irq, void *dev_instance)
struct ata_host *host = dev_instance;
unsigned int hc, handled = 0, n_hcs;
void __iomem *mmio = host->iomap[MV_PRIMARY_BAR];
- u32 irq_stat;
+ u32 irq_stat, irq_mask;
+ spin_lock(&host->lock);
irq_stat = readl(mmio + HC_MAIN_IRQ_CAUSE_OFS);
+ irq_mask = readl(mmio + HC_MAIN_IRQ_MASK_OFS);
/* check the cases where we either have nothing pending or have read
* a bogus register value which can indicate HW removal or PCI fault
*/
- if (!irq_stat || (0xffffffffU == irq_stat))
- return IRQ_NONE;
+ if (!(irq_stat & irq_mask) || (0xffffffffU == irq_stat))
+ goto out_unlock;
n_hcs = mv_get_hc_count(host->ports[0]->flags);
- spin_lock(&host->lock);
- if (unlikely(irq_stat & PCI_ERR)) {
+ if (unlikely((irq_stat & PCI_ERR) && HAS_PCI(host))) {
mv_pci_error(host, mmio);
handled = 1;
goto out_unlock; /* skip all other HC irq handling */
@@ -1799,8 +1851,9 @@ static int mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
return -EINVAL;
}
-static void mv5_reset_bus(struct pci_dev *pdev, void __iomem *mmio)
+static void mv5_reset_bus(struct ata_host *host, void __iomem *mmio)
{
+ struct pci_dev *pdev = to_pci_dev(host->dev);
int early_5080;
early_5080 = (pdev->device == 0x5080) && (pdev->revision == 0);
@@ -1811,7 +1864,7 @@ static void mv5_reset_bus(struct pci_dev *pdev, void __iomem *mmio)
writel(tmp, mmio + MV_PCI_EXP_ROM_BAR_CTL);
}
- mv_reset_pci_bus(pdev, mmio);
+ mv_reset_pci_bus(host, mmio);
}
static void mv5_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio)
@@ -1935,9 +1988,8 @@ static int mv5_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio,
#undef ZERO
#define ZERO(reg) writel(0, mmio + (reg))
-static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio)
+static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio)
{
- struct ata_host *host = dev_get_drvdata(&pdev->dev);
struct mv_host_priv *hpriv = host->private_data;
u32 tmp;
@@ -2329,11 +2381,6 @@ static void mv_error_handler(struct ata_port *ap)
mv_hardreset, mv_postreset);
}
-static void mv_post_int_cmd(struct ata_queued_cmd *qc)
-{
- mv_stop_dma(qc->ap);
-}
-
static void mv_eh_freeze(struct ata_port *ap)
{
void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
@@ -2427,8 +2474,8 @@ static void mv_port_init(struct ata_ioports *port, void __iomem *port_mmio)
writelfl(readl(port_mmio + serr_ofs), port_mmio + serr_ofs);
writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
- /* unmask all EDMA error interrupts */
- writelfl(~0, port_mmio + EDMA_ERR_IRQ_MASK_OFS);
+ /* unmask all non-transient EDMA error interrupts */
+ writelfl(~EDMA_ERR_IRQ_TRANSIENT, port_mmio + EDMA_ERR_IRQ_MASK_OFS);
VPRINTK("EDMA cfg=0x%08x EDMA IRQ err cause/mask=0x%08x/0x%08x\n",
readl(port_mmio + EDMA_CFG_OFS),
@@ -2586,7 +2633,6 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
static int mv_init_host(struct ata_host *host, unsigned int board_idx)
{
int rc = 0, n_hc, port, hc;
- struct pci_dev *pdev = to_pci_dev(host->dev);
void __iomem *mmio = host->iomap[MV_PRIMARY_BAR];
struct mv_host_priv *hpriv = host->private_data;
@@ -2607,7 +2653,7 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
goto done;
hpriv->ops->reset_flash(hpriv, mmio);
- hpriv->ops->reset_bus(pdev, mmio);
+ hpriv->ops->reset_bus(host, mmio);
hpriv->ops->enable_leds(hpriv, mmio);
for (port = 0; port < host->n_ports; port++) {
@@ -2630,8 +2676,10 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
mv_port_init(&ap->ioaddr, port_mmio);
+#ifdef CONFIG_PCI
ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio");
ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port");
+#endif
}
for (hc = 0; hc < n_hc; hc++) {
@@ -2668,6 +2716,55 @@ done:
return rc;
}
+#ifdef CONFIG_PCI
+static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
+
+static struct pci_driver mv_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = mv_pci_tbl,
+ .probe = mv_init_one,
+ .remove = ata_pci_remove_one,
+};
+
+/*
+ * module options
+ */
+static int msi; /* Use PCI msi; either zero (off, default) or non-zero */
+
+
+/* move to PCI layer or libata core? */
+static int pci_go_64(struct pci_dev *pdev)
+{
+ int rc;
+
+ if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
+ rc = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
+ if (rc) {
+ rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
+ if (rc) {
+ dev_printk(KERN_ERR, &pdev->dev,
+ "64-bit DMA enable failed\n");
+ return rc;
+ }
+ }
+ } else {
+ rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
+ if (rc) {
+ dev_printk(KERN_ERR, &pdev->dev,
+ "32-bit DMA enable failed\n");
+ return rc;
+ }
+ rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
+ if (rc) {
+ dev_printk(KERN_ERR, &pdev->dev,
+ "32-bit consistent DMA enable failed\n");
+ return rc;
+ }
+ }
+
+ return rc;
+}
+
/**
* mv_print_info - Dump key info to kernel log for perusal.
* @host: ATA host to print info about
@@ -2710,6 +2807,26 @@ static void mv_print_info(struct ata_host *host)
scc_s, (MV_HP_FLAG_MSI & hpriv->hp_flags) ? "MSI" : "INTx");
}
+static int mv_create_dma_pools(struct mv_host_priv *hpriv, struct device *dev)
+{
+ hpriv->crqb_pool = dmam_pool_create("crqb_q", dev, MV_CRQB_Q_SZ,
+ MV_CRQB_Q_SZ, 0);
+ if (!hpriv->crqb_pool)
+ return -ENOMEM;
+
+ hpriv->crpb_pool = dmam_pool_create("crpb_q", dev, MV_CRPB_Q_SZ,
+ MV_CRPB_Q_SZ, 0);
+ if (!hpriv->crpb_pool)
+ return -ENOMEM;
+
+ hpriv->sg_tbl_pool = dmam_pool_create("sg_tbl", dev, MV_SG_TBL_SZ,
+ MV_SG_TBL_SZ, 0);
+ if (!hpriv->sg_tbl_pool)
+ return -ENOMEM;
+
+ return 0;
+}
+
/**
* mv_init_one - handle a positive probe of a Marvell host
* @pdev: PCI device found
@@ -2755,6 +2872,10 @@ static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (rc)
return rc;
+ rc = mv_create_dma_pools(hpriv, &pdev->dev);
+ if (rc)
+ return rc;
+
/* initialize adapter */
rc = mv_init_host(host, board_idx);
if (rc)
@@ -2772,15 +2893,22 @@ static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
return ata_host_activate(host, pdev->irq, mv_interrupt, IRQF_SHARED,
IS_GEN_I(hpriv) ? &mv5_sht : &mv6_sht);
}
+#endif
static int __init mv_init(void)
{
- return pci_register_driver(&mv_pci_driver);
+ int rc = -ENODEV;
+#ifdef CONFIG_PCI
+ rc = pci_register_driver(&mv_pci_driver);
+#endif
+ return rc;
}
static void __exit mv_exit(void)
{
+#ifdef CONFIG_PCI
pci_unregister_driver(&mv_pci_driver);
+#endif
}
MODULE_AUTHOR("Brett Russ");
@@ -2789,8 +2917,10 @@ MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, mv_pci_tbl);
MODULE_VERSION(DRV_VERSION);
+#ifdef CONFIG_PCI
module_param(msi, int, 0444);
MODULE_PARM_DESC(msi, "Enable use of PCI MSI (0=off, 1=on)");
+#endif
module_init(mv_init);
module_exit(mv_exit);
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index a0f98fd..bfe92a4 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -1011,14 +1011,20 @@ static irqreturn_t nv_adma_interrupt(int irq, void *dev_instance)
}
if (status & (NV_ADMA_STAT_DONE |
- NV_ADMA_STAT_CPBERR)) {
- u32 check_commands;
+ NV_ADMA_STAT_CPBERR |
+ NV_ADMA_STAT_CMD_COMPLETE)) {
+ u32 check_commands = notifier_clears[i];
int pos, error = 0;
- if (ata_tag_valid(ap->link.active_tag))
- check_commands = 1 << ap->link.active_tag;
- else
- check_commands = ap->link.sactive;
+ if (status & NV_ADMA_STAT_CPBERR) {
+ /* Check all active commands */
+ if (ata_tag_valid(ap->link.active_tag))
+ check_commands = 1 <<
+ ap->link.active_tag;
+ else
+ check_commands = ap->
+ link.sactive;
+ }
/** Check CPBs for completed commands */
while ((pos = ffs(check_commands)) && !error) {
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index 71d561f..7d4ce90 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -823,7 +823,8 @@ int pcim_enable_device(struct pci_dev *pdev)
dr = get_pci_dr(pdev);
if (unlikely(!dr))
return -ENOMEM;
- WARN_ON(!!dr->enabled);
+ if (dr->enabled)
+ return 0;
rc = pci_enable_device(pdev);
if (!rc) {
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2008-01-25 23:16 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2008-01-25 23:16 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Honestly, this is the least interesting merge push I've had in a while.
We're all doing debugging and such, so nothing major is below.
I have some queued stuff (notably a sata_mv update) still to come, but
this is the stuff that's been pending and in -mm for a while.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/Kconfig | 9 +
drivers/ata/Makefile | 1 +
drivers/ata/ahci.c | 72 ++--
drivers/ata/ata_generic.c | 51 ++-
drivers/ata/ata_piix.c | 393 ++++++++++++++----
drivers/ata/libata-acpi.c | 117 ++++--
drivers/ata/libata-core.c | 805 ++++++++++++++++------------------
drivers/ata/libata-eh.c | 299 ++++++++++---
drivers/ata/libata-scsi.c | 40 ++-
drivers/ata/libata-sff.c | 199 +++++----
drivers/ata/libata.h | 6 +-
drivers/ata/pata_acpi.c | 67 +---
drivers/ata/pata_ali.c | 2 +-
drivers/ata/pata_amd.c | 128 ++++--
drivers/ata/pata_bf54x.c | 41 +-
drivers/ata/pata_cs5520.c | 2 +-
drivers/ata/pata_hpt37x.c | 7 +-
drivers/ata/pata_icside.c | 3 +-
drivers/ata/pata_it821x.c | 35 ++-
drivers/ata/pata_ixp4xx_cf.c | 26 +-
drivers/ata/pata_legacy.c | 912 +++++++++++++++++++++++++++++++--------
drivers/ata/pata_mpc52xx.c | 2 +-
drivers/ata/pata_ninja32.c | 214 +++++++++
drivers/ata/pata_pcmcia.c | 101 ++++-
drivers/ata/pata_pdc2027x.c | 2 +-
drivers/ata/pata_pdc202xx_old.c | 5 +-
drivers/ata/pata_qdi.c | 30 +-
drivers/ata/pata_scc.c | 30 +-
drivers/ata/pata_serverworks.c | 9 +-
drivers/ata/pata_via.c | 3 +-
drivers/ata/pata_winbond.c | 30 +-
drivers/ata/pdc_adma.c | 5 +-
drivers/ata/sata_fsl.c | 5 +-
drivers/ata/sata_inic162x.c | 2 +-
drivers/ata/sata_mv.c | 3 +-
drivers/ata/sata_nv.c | 25 +-
drivers/ata/sata_promise.c | 98 ++---
drivers/ata/sata_promise.h | 2 +-
drivers/ata/sata_qstor.c | 15 +-
drivers/ata/sata_sil.c | 10 +-
drivers/ata/sata_sil24.c | 30 +-
drivers/ata/sata_sx4.c | 15 +-
drivers/scsi/ipr.c | 9 +-
drivers/scsi/libsas/sas_ata.c | 14 +-
include/linux/ata.h | 110 ++++-
include/linux/cdrom.h | 3 +
include/linux/libata.h | 184 +++++---
include/linux/pci_ids.h | 3 +
48 files changed, 2851 insertions(+), 1323 deletions(-)
create mode 100644 drivers/ata/pata_ninja32.c
Al Viro (1):
libata annotations and fixes
Alan Cox (13):
libata: Disable ATA8-ACS proposed Trusted Computing features by default
libata: IORDY handling
libata-sff: tf_load
pata_ninja32: Cardbus ATA initial support
pata_pcmcia: Add support for dumb 8bit IDE emulations
libata/pata_it821x: Improve handling of poorly compatible emulations
pata_pcmcia: Minor cleanups and support for dual channel cards
pata_legacy: resychronize with upstream changes and resubmit
pata_mpc52xx: remove un-needed assignment
pata_serverworks: Fix cable types and cosmetics
pata_winbond: error return
ata_generic: Cenatek support
pata_legacy: Merge winbond support
Albert Lee (1):
libata: zero xfer length on ATAPI data xfer IRQ is HSM violation
Andrew Morton (4):
drivers/ata/libata-eh.c: fix printk warning
pata_hpt37x: checkpatch fixes
[libata] pata_winbond: update for new ->data_xfer hook
[libata] pata_legacy: typo fix
James Bottomley (1):
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
Jeff Garzik (3):
libata: checkpatch fixes
[libata] Build fix WRT ata_is_xxx() new API introduction
libata: make ata_port_queue_task() an internal function
Peter Schwenke (1):
ata_piix: Add Toshiba Satellite R20 and Tecra M6 to broken suspend list.
Shaohua Li (1):
libata-acpi: add ACPI _PSx method
Tejun Heo (40):
ahci: update PCS programming
libata: rearrange ATA_DFLAG_*
libata: implement protocol tests
libata: factor out ata_eh_schedule_probe()
libata: move ata_set_mode() to libata-eh.c
libata: clean up EH speed down implementation
libata: adjust speed down rules
libata: implement ATA_DFLAG_DUBIOUS_XFER
libata: implement fast speed down for unverified data transfer mode
ata_generic: unindent loop in generic_set_mode()
libata: export xfermode / PATA timing related functions
libata: clean up xfermode / PATA timing related stuff
libata: kill ata_id_to_dma_mode()
libata: xfer_mask is unsigned long not unsigned int
libata: add ATA_CBL_PATA_IGN
sata_promise: make pdc_atapi_pkt() use values from qc->tf
ata_piix: separate controller IDs into separate enum
libata: separate out ata_acpi_gtm_xfermask() from pacpi_discover_modes()
libata: fix ata_acpi_gtm_xfermask()
libata: implement ata_timing_cycle2mode() and use it in libata-acpi and pata_acpi
libata: reimplement ata_acpi_cbl_80wire() using ata_acpi_gtm_xfermask()
pata_amd: update mode selection for NV PATAs
libata: convert NCQ test in ata_qc_issue() to ata_is_ncq()
libata: make atapi_request_sense() use sg
cdrom: add more GPCMD_* constants
libata: rename ATA_PROT_ATAPI_* to ATAPI_PROT_*
libata: add ATAPI_* cmd types and implement atapi_cmd_type()
libata: update ->data_xfer hook for ATAPI
libata: kill non-sg DMA interface
libata: change ATA_QCFLAG_DMAMAP semantics
libata: convert to chained sg
libata: make qc->nbytes include extra buffers
ata_piix: kill unused constants and flags
libata: use dev_driver_string() instead of "libata" in libata-sff.c
pata_pcmcia: convert to new data_xfer prototype
libata: factor out ata_pci_activate_sff_host() from ata_pci_one()
ata_piix: convert to prepare - activate initialization
ata_piix: implement SIDPR SCR access
ahci: factor out AHCI enabling and enable AHCI before reading CAP
libata: fix off-by-one in error categorization
akpm@linux-foundation.org (2):
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
fix drivers/ata/sata_fsl.c double-decl
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index ba63619..2478cca 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -459,6 +459,15 @@ config PATA_NETCELL
If unsure, say N.
+config PATA_NINJA32
+ tristate "Ninja32/Delkin Cardbus ATA support (Experimental)"
+ depends on PCI && EXPERIMENTAL
+ help
+ This option enables support for the Ninja32, Delkin and
+ possibly other brands of Cardbus ATA adapter
+
+ If unsure, say N.
+
config PATA_NS87410
tristate "Nat Semi NS87410 PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index b13feb2..82550c1 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -41,6 +41,7 @@ obj-$(CONFIG_PATA_IT821X) += pata_it821x.o
obj-$(CONFIG_PATA_IT8213) += pata_it8213.o
obj-$(CONFIG_PATA_JMICRON) += pata_jmicron.o
obj-$(CONFIG_PATA_NETCELL) += pata_netcell.o
+obj-$(CONFIG_PATA_NINJA32) += pata_ninja32.o
obj-$(CONFIG_PATA_NS87410) += pata_ns87410.o
obj-$(CONFIG_PATA_NS87415) += pata_ns87415.o
obj-$(CONFIG_PATA_OPTI) += pata_opti.o
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 54f38c2..6f089b8 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -198,18 +198,18 @@ enum {
};
struct ahci_cmd_hdr {
- u32 opts;
- u32 status;
- u32 tbl_addr;
- u32 tbl_addr_hi;
- u32 reserved[4];
+ __le32 opts;
+ __le32 status;
+ __le32 tbl_addr;
+ __le32 tbl_addr_hi;
+ __le32 reserved[4];
};
struct ahci_sg {
- u32 addr;
- u32 addr_hi;
- u32 reserved;
- u32 flags_size;
+ __le32 addr;
+ __le32 addr_hi;
+ __le32 reserved;
+ __le32 flags_size;
};
struct ahci_host_priv {
@@ -597,6 +597,20 @@ static inline void __iomem *ahci_port_base(struct ata_port *ap)
return __ahci_port_base(ap->host, ap->port_no);
}
+static void ahci_enable_ahci(void __iomem *mmio)
+{
+ u32 tmp;
+
+ /* turn on AHCI_EN */
+ tmp = readl(mmio + HOST_CTL);
+ if (!(tmp & HOST_AHCI_EN)) {
+ tmp |= HOST_AHCI_EN;
+ writel(tmp, mmio + HOST_CTL);
+ tmp = readl(mmio + HOST_CTL); /* flush && sanity check */
+ WARN_ON(!(tmp & HOST_AHCI_EN));
+ }
+}
+
/**
* ahci_save_initial_config - Save and fixup initial config values
* @pdev: target PCI device
@@ -619,6 +633,9 @@ static void ahci_save_initial_config(struct pci_dev *pdev,
u32 cap, port_map;
int i;
+ /* make sure AHCI mode is enabled before accessing CAP */
+ ahci_enable_ahci(mmio);
+
/* Values prefixed with saved_ are written back to host after
* reset. Values without are used for driver operation.
*/
@@ -1036,19 +1053,17 @@ static int ahci_deinit_port(struct ata_port *ap, const char **emsg)
static int ahci_reset_controller(struct ata_host *host)
{
struct pci_dev *pdev = to_pci_dev(host->dev);
+ struct ahci_host_priv *hpriv = host->private_data;
void __iomem *mmio = host->iomap[AHCI_PCI_BAR];
u32 tmp;
/* we must be in AHCI mode, before using anything
* AHCI-specific, such as HOST_RESET.
*/
- tmp = readl(mmio + HOST_CTL);
- if (!(tmp & HOST_AHCI_EN)) {
- tmp |= HOST_AHCI_EN;
- writel(tmp, mmio + HOST_CTL);
- }
+ ahci_enable_ahci(mmio);
/* global controller reset */
+ tmp = readl(mmio + HOST_CTL);
if ((tmp & HOST_RESET) == 0) {
writel(tmp | HOST_RESET, mmio + HOST_CTL);
readl(mmio + HOST_CTL); /* flush */
@@ -1067,8 +1082,7 @@ static int ahci_reset_controller(struct ata_host *host)
}
/* turn on AHCI mode */
- writel(HOST_AHCI_EN, mmio + HOST_CTL);
- (void) readl(mmio + HOST_CTL); /* flush */
+ ahci_enable_ahci(mmio);
/* some registers might be cleared on reset. restore initial values */
ahci_restore_initial_config(host);
@@ -1078,8 +1092,10 @@ static int ahci_reset_controller(struct ata_host *host)
/* configure PCS */
pci_read_config_word(pdev, 0x92, &tmp16);
- tmp16 |= 0xf;
- pci_write_config_word(pdev, 0x92, tmp16);
+ if ((tmp16 & hpriv->port_map) != hpriv->port_map) {
+ tmp16 |= hpriv->port_map;
+ pci_write_config_word(pdev, 0x92, tmp16);
+ }
}
return 0;
@@ -1480,35 +1496,31 @@ static void ahci_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
static unsigned int ahci_fill_sg(struct ata_queued_cmd *qc, void *cmd_tbl)
{
struct scatterlist *sg;
- struct ahci_sg *ahci_sg;
- unsigned int n_sg = 0;
+ struct ahci_sg *ahci_sg = cmd_tbl + AHCI_CMD_TBL_HDR_SZ;
+ unsigned int si;
VPRINTK("ENTER\n");
/*
* Next, the S/G list.
*/
- ahci_sg = cmd_tbl + AHCI_CMD_TBL_HDR_SZ;
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
dma_addr_t addr = sg_dma_address(sg);
u32 sg_len = sg_dma_len(sg);
- ahci_sg->addr = cpu_to_le32(addr & 0xffffffff);
- ahci_sg->addr_hi = cpu_to_le32((addr >> 16) >> 16);
- ahci_sg->flags_size = cpu_to_le32(sg_len - 1);
-
- ahci_sg++;
- n_sg++;
+ ahci_sg[si].addr = cpu_to_le32(addr & 0xffffffff);
+ ahci_sg[si].addr_hi = cpu_to_le32((addr >> 16) >> 16);
+ ahci_sg[si].flags_size = cpu_to_le32(sg_len - 1);
}
- return n_sg;
+ return si;
}
static void ahci_qc_prep(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ahci_port_priv *pp = ap->private_data;
- int is_atapi = is_atapi_taskfile(&qc->tf);
+ int is_atapi = ata_is_atapi(qc->tf.protocol);
void *cmd_tbl;
u32 opts;
const u32 cmd_fis_len = 5; /* five dwords */
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
index 9032998..2053420 100644
--- a/drivers/ata/ata_generic.c
+++ b/drivers/ata/ata_generic.c
@@ -26,7 +26,7 @@
#include <linux/libata.h>
#define DRV_NAME "ata_generic"
-#define DRV_VERSION "0.2.13"
+#define DRV_VERSION "0.2.15"
/*
* A generic parallel ATA driver using libata
@@ -48,27 +48,47 @@ static int generic_set_mode(struct ata_link *link, struct ata_device **unused)
struct ata_port *ap = link->ap;
int dma_enabled = 0;
struct ata_device *dev;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
/* Bits 5 and 6 indicate if DMA is active on master/slave */
if (ap->ioaddr.bmdma_addr)
dma_enabled = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+ if (pdev->vendor == PCI_VENDOR_ID_CENATEK)
+ dma_enabled = 0xFF;
+
ata_link_for_each_dev(dev, link) {
- if (ata_dev_enabled(dev)) {
- /* We don't really care */
- dev->pio_mode = XFER_PIO_0;
- dev->dma_mode = XFER_MW_DMA_0;
- /* We do need the right mode information for DMA or PIO
- and this comes from the current configuration flags */
- if (dma_enabled & (1 << (5 + dev->devno))) {
- ata_id_to_dma_mode(dev, XFER_MW_DMA_0);
- dev->flags &= ~ATA_DFLAG_PIO;
- } else {
- ata_dev_printk(dev, KERN_INFO, "configured for PIO\n");
- dev->xfer_mode = XFER_PIO_0;
- dev->xfer_shift = ATA_SHIFT_PIO;
- dev->flags |= ATA_DFLAG_PIO;
+ if (!ata_dev_enabled(dev))
+ continue;
+
+ /* We don't really care */
+ dev->pio_mode = XFER_PIO_0;
+ dev->dma_mode = XFER_MW_DMA_0;
+ /* We do need the right mode information for DMA or PIO
+ and this comes from the current configuration flags */
+ if (dma_enabled & (1 << (5 + dev->devno))) {
+ unsigned int xfer_mask = ata_id_xfermask(dev->id);
+ const char *name;
+
+ if (xfer_mask & (ATA_MASK_MWDMA | ATA_MASK_UDMA))
+ name = ata_mode_string(xfer_mask);
+ else {
+ /* SWDMA perhaps? */
+ name = "DMA";
+ xfer_mask |= ata_xfer_mode2mask(XFER_MW_DMA_0);
}
+
+ ata_dev_printk(dev, KERN_INFO, "configured for %s\n",
+ name);
+
+ dev->xfer_mode = ata_xfer_mask2mode(xfer_mask);
+ dev->xfer_shift = ata_xfer_mode2shift(dev->xfer_mode);
+ dev->flags &= ~ATA_DFLAG_PIO;
+ } else {
+ ata_dev_printk(dev, KERN_INFO, "configured for PIO\n");
+ dev->xfer_mode = XFER_PIO_0;
+ dev->xfer_shift = ATA_SHIFT_PIO;
+ dev->flags |= ATA_DFLAG_PIO;
}
}
return 0;
@@ -185,6 +205,7 @@ static struct pci_device_id ata_generic[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_HINT, PCI_DEVICE_ID_HINT_VXPROII_IDE), },
{ PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C561), },
{ PCI_DEVICE(PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C558), },
+ { PCI_DEVICE(PCI_VENDOR_ID_CENATEK,PCI_DEVICE_ID_CENATEK_IDE), },
{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO), },
{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_1), },
{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_2), },
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index b406b39..a65c8ae 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -101,39 +101,21 @@ enum {
ICH5_PMR = 0x90, /* port mapping register */
ICH5_PCS = 0x92, /* port control and status */
PIIX_SCC = 0x0A, /* sub-class code register */
+ PIIX_SIDPR_BAR = 5,
+ PIIX_SIDPR_LEN = 16,
+ PIIX_SIDPR_IDX = 0,
+ PIIX_SIDPR_DATA = 4,
- PIIX_FLAG_SCR = (1 << 26), /* SCR available */
PIIX_FLAG_AHCI = (1 << 27), /* AHCI possible */
PIIX_FLAG_CHECKINTR = (1 << 28), /* make sure PCI INTx enabled */
+ PIIX_FLAG_SIDPR = (1 << 29), /* SATA idx/data pair regs */
PIIX_PATA_FLAGS = ATA_FLAG_SLAVE_POSS,
PIIX_SATA_FLAGS = ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR,
- /* combined mode. if set, PATA is channel 0.
- * if clear, PATA is channel 1.
- */
- PIIX_PORT_ENABLED = (1 << 0),
- PIIX_PORT_PRESENT = (1 << 4),
-
PIIX_80C_PRI = (1 << 5) | (1 << 4),
PIIX_80C_SEC = (1 << 7) | (1 << 6),
- /* controller IDs */
- piix_pata_mwdma = 0, /* PIIX3 MWDMA only */
- piix_pata_33, /* PIIX4 at 33Mhz */
- ich_pata_33, /* ICH up to UDMA 33 only */
- ich_pata_66, /* ICH up to 66 Mhz */
- ich_pata_100, /* ICH up to UDMA 100 */
- ich5_sata,
- ich6_sata,
- ich6_sata_ahci,
- ich6m_sata_ahci,
- ich8_sata_ahci,
- ich8_2port_sata,
- ich8m_apple_sata_ahci, /* locks up on second port enable */
- tolapai_sata_ahci,
- piix_pata_vmw, /* PIIX4 for VMware, spurious DMA_ERR */
-
/* constants for mapping table */
P0 = 0, /* port 0 */
P1 = 1, /* port 1 */
@@ -149,6 +131,24 @@ enum {
PIIX_HOST_BROKEN_SUSPEND = (1 << 24),
};
+enum piix_controller_ids {
+ /* controller IDs */
+ piix_pata_mwdma, /* PIIX3 MWDMA only */
+ piix_pata_33, /* PIIX4 at 33Mhz */
+ ich_pata_33, /* ICH up to UDMA 33 only */
+ ich_pata_66, /* ICH up to 66 Mhz */
+ ich_pata_100, /* ICH up to UDMA 100 */
+ ich5_sata,
+ ich6_sata,
+ ich6_sata_ahci,
+ ich6m_sata_ahci,
+ ich8_sata_ahci,
+ ich8_2port_sata,
+ ich8m_apple_sata_ahci, /* locks up on second port enable */
+ tolapai_sata_ahci,
+ piix_pata_vmw, /* PIIX4 for VMware, spurious DMA_ERR */
+};
+
struct piix_map_db {
const u32 mask;
const u16 port_enable;
@@ -157,6 +157,7 @@ struct piix_map_db {
struct piix_host_priv {
const int *map;
+ void __iomem *sidpr;
};
static int piix_init_one(struct pci_dev *pdev,
@@ -167,6 +168,9 @@ static void piix_set_dmamode(struct ata_port *ap, struct ata_device *adev);
static void ich_set_dmamode(struct ata_port *ap, struct ata_device *adev);
static int ich_pata_cable_detect(struct ata_port *ap);
static u8 piix_vmw_bmdma_status(struct ata_port *ap);
+static int piix_sidpr_scr_read(struct ata_port *ap, unsigned int reg, u32 *val);
+static int piix_sidpr_scr_write(struct ata_port *ap, unsigned int reg, u32 val);
+static void piix_sidpr_error_handler(struct ata_port *ap);
#ifdef CONFIG_PM
static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
static int piix_pci_device_resume(struct pci_dev *pdev);
@@ -321,7 +325,6 @@ static const struct ata_port_operations piix_pata_ops = {
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.cable_detect = ata_cable_40wire,
- .irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
@@ -353,7 +356,6 @@ static const struct ata_port_operations ich_pata_ops = {
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.cable_detect = ich_pata_cable_detect,
- .irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
@@ -380,7 +382,6 @@ static const struct ata_port_operations piix_sata_ops = {
.error_handler = ata_bmdma_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
- .irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
@@ -419,6 +420,35 @@ static const struct ata_port_operations piix_vmw_ops = {
.port_start = ata_port_start,
};
+static const struct ata_port_operations piix_sidpr_sata_ops = {
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_data_xfer,
+
+ .scr_read = piix_sidpr_scr_read,
+ .scr_write = piix_sidpr_scr_write,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = piix_sidpr_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+
+ .port_start = ata_port_start,
+};
+
static const struct piix_map_db ich5_map_db = {
.mask = 0x7,
.port_enable = 0x3,
@@ -526,7 +556,6 @@ static const struct piix_map_db *piix_map_db_table[] = {
static struct ata_port_info piix_port_info[] = {
[piix_pata_mwdma] = /* PIIX3 MWDMA only */
{
- .sht = &piix_sht,
.flags = PIIX_PATA_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
@@ -535,7 +564,6 @@ static struct ata_port_info piix_port_info[] = {
[piix_pata_33] = /* PIIX4 at 33MHz */
{
- .sht = &piix_sht,
.flags = PIIX_PATA_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
@@ -545,7 +573,6 @@ static struct ata_port_info piix_port_info[] = {
[ich_pata_33] = /* ICH0 - ICH at 33Mhz*/
{
- .sht = &piix_sht,
.flags = PIIX_PATA_FLAGS,
.pio_mask = 0x1f, /* pio 0-4 */
.mwdma_mask = 0x06, /* Check: maybe 0x07 */
@@ -555,7 +582,6 @@ static struct ata_port_info piix_port_info[] = {
[ich_pata_66] = /* ICH controllers up to 66MHz */
{
- .sht = &piix_sht,
.flags = PIIX_PATA_FLAGS,
.pio_mask = 0x1f, /* pio 0-4 */
.mwdma_mask = 0x06, /* MWDMA0 is broken on chip */
@@ -565,7 +591,6 @@ static struct ata_port_info piix_port_info[] = {
[ich_pata_100] =
{
- .sht = &piix_sht,
.flags = PIIX_PATA_FLAGS | PIIX_FLAG_CHECKINTR,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x06, /* mwdma1-2 */
@@ -575,7 +600,6 @@ static struct ata_port_info piix_port_info[] = {
[ich5_sata] =
{
- .sht = &piix_sht,
.flags = PIIX_SATA_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
@@ -585,8 +609,7 @@ static struct ata_port_info piix_port_info[] = {
[ich6_sata] =
{
- .sht = &piix_sht,
- .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR,
+ .flags = PIIX_SATA_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
@@ -595,9 +618,7 @@ static struct ata_port_info piix_port_info[] = {
[ich6_sata_ahci] =
{
- .sht = &piix_sht,
- .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
- PIIX_FLAG_AHCI,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
@@ -606,9 +627,7 @@ static struct ata_port_info piix_port_info[] = {
[ich6m_sata_ahci] =
{
- .sht = &piix_sht,
- .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
- PIIX_FLAG_AHCI,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
@@ -617,9 +636,8 @@ static struct ata_port_info piix_port_info[] = {
[ich8_sata_ahci] =
{
- .sht = &piix_sht,
- .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
- PIIX_FLAG_AHCI,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_AHCI |
+ PIIX_FLAG_SIDPR,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
@@ -628,9 +646,8 @@ static struct ata_port_info piix_port_info[] = {
[ich8_2port_sata] =
{
- .sht = &piix_sht,
- .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
- PIIX_FLAG_AHCI,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_AHCI |
+ PIIX_FLAG_SIDPR,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
@@ -639,9 +656,7 @@ static struct ata_port_info piix_port_info[] = {
[tolapai_sata_ahci] =
{
- .sht = &piix_sht,
- .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
- PIIX_FLAG_AHCI,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
@@ -650,9 +665,8 @@ static struct ata_port_info piix_port_info[] = {
[ich8m_apple_sata_ahci] =
{
- .sht = &piix_sht,
- .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
- PIIX_FLAG_AHCI,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_AHCI |
+ PIIX_FLAG_SIDPR,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
@@ -1001,6 +1015,180 @@ static void ich_set_dmamode(struct ata_port *ap, struct ata_device *adev)
do_pata_set_dmamode(ap, adev, 1);
}
+/*
+ * Serial ATA Index/Data Pair Superset Registers access
+ *
+ * Beginning from ICH8, there's a sane way to access SCRs using index
+ * and data register pair located at BAR5. This creates an
+ * interesting problem of mapping two SCRs to one port.
+ *
+ * Although they have separate SCRs, the master and slave aren't
+ * independent enough to be treated as separate links - e.g. softreset
+ * resets both. Also, there's no protocol defined for hard resetting
+ * singled device sharing the virtual port (no defined way to acquire
+ * device signature). This is worked around by merging the SCR values
+ * into one sensible value and requesting follow-up SRST after
+ * hardreset.
+ *
+ * SCR merging is perfomed in nibbles which is the unit contents in
+ * SCRs are organized. If two values are equal, the value is used.
+ * When they differ, merge table which lists precedence of possible
+ * values is consulted and the first match or the last entry when
+ * nothing matches is used. When there's no merge table for the
+ * specific nibble, value from the first port is used.
+ */
+static const int piix_sidx_map[] = {
+ [SCR_STATUS] = 0,
+ [SCR_ERROR] = 2,
+ [SCR_CONTROL] = 1,
+};
+
+static void piix_sidpr_sel(struct ata_device *dev, unsigned int reg)
+{
+ struct ata_port *ap = dev->link->ap;
+ struct piix_host_priv *hpriv = ap->host->private_data;
+
+ iowrite32(((ap->port_no * 2 + dev->devno) << 8) | piix_sidx_map[reg],
+ hpriv->sidpr + PIIX_SIDPR_IDX);
+}
+
+static int piix_sidpr_read(struct ata_device *dev, unsigned int reg)
+{
+ struct piix_host_priv *hpriv = dev->link->ap->host->private_data;
+
+ piix_sidpr_sel(dev, reg);
+ return ioread32(hpriv->sidpr + PIIX_SIDPR_DATA);
+}
+
+static void piix_sidpr_write(struct ata_device *dev, unsigned int reg, u32 val)
+{
+ struct piix_host_priv *hpriv = dev->link->ap->host->private_data;
+
+ piix_sidpr_sel(dev, reg);
+ iowrite32(val, hpriv->sidpr + PIIX_SIDPR_DATA);
+}
+
+u32 piix_merge_scr(u32 val0, u32 val1, const int * const *merge_tbl)
+{
+ u32 val = 0;
+ int i, mi;
+
+ for (i = 0, mi = 0; i < 32 / 4; i++) {
+ u8 c0 = (val0 >> (i * 4)) & 0xf;
+ u8 c1 = (val1 >> (i * 4)) & 0xf;
+ u8 merged = c0;
+ const int *cur;
+
+ /* if no merge preference, assume the first value */
+ cur = merge_tbl[mi];
+ if (!cur)
+ goto done;
+ mi++;
+
+ /* if two values equal, use it */
+ if (c0 == c1)
+ goto done;
+
+ /* choose the first match or the last from the merge table */
+ while (*cur != -1) {
+ if (c0 == *cur || c1 == *cur)
+ break;
+ cur++;
+ }
+ if (*cur == -1)
+ cur--;
+ merged = *cur;
+ done:
+ val |= merged << (i * 4);
+ }
+
+ return val;
+}
+
+static int piix_sidpr_scr_read(struct ata_port *ap, unsigned int reg, u32 *val)
+{
+ const int * const sstatus_merge_tbl[] = {
+ /* DET */ (const int []){ 1, 3, 0, 4, 3, -1 },
+ /* SPD */ (const int []){ 2, 1, 0, -1 },
+ /* IPM */ (const int []){ 6, 2, 1, 0, -1 },
+ NULL,
+ };
+ const int * const scontrol_merge_tbl[] = {
+ /* DET */ (const int []){ 1, 0, 4, 0, -1 },
+ /* SPD */ (const int []){ 0, 2, 1, 0, -1 },
+ /* IPM */ (const int []){ 0, 1, 2, 3, 0, -1 },
+ NULL,
+ };
+ u32 v0, v1;
+
+ if (reg >= ARRAY_SIZE(piix_sidx_map))
+ return -EINVAL;
+
+ if (!(ap->flags & ATA_FLAG_SLAVE_POSS)) {
+ *val = piix_sidpr_read(&ap->link.device[0], reg);
+ return 0;
+ }
+
+ v0 = piix_sidpr_read(&ap->link.device[0], reg);
+ v1 = piix_sidpr_read(&ap->link.device[1], reg);
+
+ switch (reg) {
+ case SCR_STATUS:
+ *val = piix_merge_scr(v0, v1, sstatus_merge_tbl);
+ break;
+ case SCR_ERROR:
+ *val = v0 | v1;
+ break;
+ case SCR_CONTROL:
+ *val = piix_merge_scr(v0, v1, scontrol_merge_tbl);
+ break;
+ }
+
+ return 0;
+}
+
+static int piix_sidpr_scr_write(struct ata_port *ap, unsigned int reg, u32 val)
+{
+ if (reg >= ARRAY_SIZE(piix_sidx_map))
+ return -EINVAL;
+
+ piix_sidpr_write(&ap->link.device[0], reg, val);
+
+ if (ap->flags & ATA_FLAG_SLAVE_POSS)
+ piix_sidpr_write(&ap->link.device[1], reg, val);
+
+ return 0;
+}
+
+static int piix_sidpr_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
+{
+ const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
+ int rc;
+
+ /* do hardreset */
+ rc = sata_link_hardreset(link, timing, deadline);
+ if (rc) {
+ ata_link_printk(link, KERN_ERR,
+ "COMRESET failed (errno=%d)\n", rc);
+ return rc;
+ }
+
+ /* TODO: phy layer with polling, timeouts, etc. */
+ if (ata_link_offline(link)) {
+ *class = ATA_DEV_NONE;
+ return 0;
+ }
+
+ return -EAGAIN;
+}
+
+static void piix_sidpr_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, ata_std_prereset, ata_std_softreset,
+ piix_sidpr_hardreset, ata_std_postreset);
+}
+
#ifdef CONFIG_PM
static int piix_broken_suspend(void)
{
@@ -1034,6 +1222,13 @@ static int piix_broken_suspend(void)
},
},
{
+ .ident = "TECRA M6",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M6"),
+ },
+ },
+ {
.ident = "TECRA M7",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
@@ -1048,6 +1243,13 @@ static int piix_broken_suspend(void)
},
},
{
+ .ident = "Satellite R20",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Satellite R20"),
+ },
+ },
+ {
.ident = "Satellite R25",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
@@ -1253,10 +1455,10 @@ static int __devinit piix_check_450nx_errata(struct pci_dev *ata_dev)
return no_piix_dma;
}
-static void __devinit piix_init_pcs(struct pci_dev *pdev,
- struct ata_port_info *pinfo,
+static void __devinit piix_init_pcs(struct ata_host *host,
const struct piix_map_db *map_db)
{
+ struct pci_dev *pdev = to_pci_dev(host->dev);
u16 pcs, new_pcs;
pci_read_config_word(pdev, ICH5_PCS, &pcs);
@@ -1270,11 +1472,10 @@ static void __devinit piix_init_pcs(struct pci_dev *pdev,
}
}
-static void __devinit piix_init_sata_map(struct pci_dev *pdev,
- struct ata_port_info *pinfo,
- const struct piix_map_db *map_db)
+static const int *__devinit piix_init_sata_map(struct pci_dev *pdev,
+ struct ata_port_info *pinfo,
+ const struct piix_map_db *map_db)
{
- struct piix_host_priv *hpriv = pinfo[0].private_data;
const int *map;
int i, invalid_map = 0;
u8 map_value;
@@ -1298,7 +1499,6 @@ static void __devinit piix_init_sata_map(struct pci_dev *pdev,
case IDE:
WARN_ON((i & 1) || map[i + 1] != IDE);
pinfo[i / 2] = piix_port_info[ich_pata_100];
- pinfo[i / 2].private_data = hpriv;
i++;
printk(" IDE IDE");
break;
@@ -1316,7 +1516,33 @@ static void __devinit piix_init_sata_map(struct pci_dev *pdev,
dev_printk(KERN_ERR, &pdev->dev,
"invalid MAP value %u\n", map_value);
- hpriv->map = map;
+ return map;
+}
+
+static void __devinit piix_init_sidpr(struct ata_host *host)
+{
+ struct pci_dev *pdev = to_pci_dev(host->dev);
+ struct piix_host_priv *hpriv = host->private_data;
+ int i;
+
+ /* check for availability */
+ for (i = 0; i < 4; i++)
+ if (hpriv->map[i] == IDE)
+ return;
+
+ if (!(host->ports[0]->flags & PIIX_FLAG_SIDPR))
+ return;
+
+ if (pci_resource_start(pdev, PIIX_SIDPR_BAR) == 0 ||
+ pci_resource_len(pdev, PIIX_SIDPR_BAR) != PIIX_SIDPR_LEN)
+ return;
+
+ if (pcim_iomap_regions(pdev, 1 << PIIX_SIDPR_BAR, DRV_NAME))
+ return;
+
+ hpriv->sidpr = pcim_iomap_table(pdev)[PIIX_SIDPR_BAR];
+ host->ports[0]->ops = &piix_sidpr_sata_ops;
+ host->ports[1]->ops = &piix_sidpr_sata_ops;
}
static void piix_iocfg_bit18_quirk(struct pci_dev *pdev)
@@ -1375,8 +1601,10 @@ static int piix_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
struct device *dev = &pdev->dev;
struct ata_port_info port_info[2];
const struct ata_port_info *ppi[] = { &port_info[0], &port_info[1] };
- struct piix_host_priv *hpriv;
unsigned long port_flags;
+ struct ata_host *host;
+ struct piix_host_priv *hpriv;
+ int rc;
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev,
@@ -1386,17 +1614,31 @@ static int piix_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (!in_module_init)
return -ENODEV;
+ port_info[0] = piix_port_info[ent->driver_data];
+ port_info[1] = piix_port_info[ent->driver_data];
+
+ port_flags = port_info[0].flags;
+
+ /* enable device and prepare host */
+ rc = pcim_enable_device(pdev);
+ if (rc)
+ return rc;
+
+ /* SATA map init can change port_info, do it before prepping host */
hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
if (!hpriv)
return -ENOMEM;
- port_info[0] = piix_port_info[ent->driver_data];
- port_info[1] = piix_port_info[ent->driver_data];
- port_info[0].private_data = hpriv;
- port_info[1].private_data = hpriv;
+ if (port_flags & ATA_FLAG_SATA)
+ hpriv->map = piix_init_sata_map(pdev, port_info,
+ piix_map_db_table[ent->driver_data]);
- port_flags = port_info[0].flags;
+ rc = ata_pci_prepare_sff_host(pdev, ppi, &host);
+ if (rc)
+ return rc;
+ host->private_data = hpriv;
+ /* initialize controller */
if (port_flags & PIIX_FLAG_AHCI) {
u8 tmp;
pci_read_config_byte(pdev, PIIX_SCC, &tmp);
@@ -1407,12 +1649,9 @@ static int piix_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
}
}
- /* Initialize SATA map */
if (port_flags & ATA_FLAG_SATA) {
- piix_init_sata_map(pdev, port_info,
- piix_map_db_table[ent->driver_data]);
- piix_init_pcs(pdev, port_info,
- piix_map_db_table[ent->driver_data]);
+ piix_init_pcs(host, piix_map_db_table[ent->driver_data]);
+ piix_init_sidpr(host);
}
/* apply IOCFG bit18 quirk */
@@ -1431,12 +1670,14 @@ static int piix_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
/* This writes into the master table but it does not
really matter for this errata as we will apply it to
all the PIIX devices on the board */
- port_info[0].mwdma_mask = 0;
- port_info[0].udma_mask = 0;
- port_info[1].mwdma_mask = 0;
- port_info[1].udma_mask = 0;
+ host->ports[0]->mwdma_mask = 0;
+ host->ports[0]->udma_mask = 0;
+ host->ports[1]->mwdma_mask = 0;
+ host->ports[1]->udma_mask = 0;
}
- return ata_pci_init_one(pdev, ppi);
+
+ pci_set_master(pdev);
+ return ata_pci_activate_sff_host(host, ata_interrupt, &piix_sht);
}
static int __init piix_init(void)
diff --git a/drivers/ata/libata-acpi.c b/drivers/ata/libata-acpi.c
index 7bf4bef..9e8ec19 100644
--- a/drivers/ata/libata-acpi.c
+++ b/drivers/ata/libata-acpi.c
@@ -442,40 +442,77 @@ static int ata_dev_get_GTF(struct ata_device *dev, struct ata_acpi_gtf **gtf)
}
/**
+ * ata_acpi_gtm_xfermode - determine xfermode from GTM parameter
+ * @dev: target device
+ * @gtm: GTM parameter to use
+ *
+ * Determine xfermask for @dev from @gtm.
+ *
+ * LOCKING:
+ * None.
+ *
+ * RETURNS:
+ * Determined xfermask.
+ */
+unsigned long ata_acpi_gtm_xfermask(struct ata_device *dev,
+ const struct ata_acpi_gtm *gtm)
+{
+ unsigned long xfer_mask = 0;
+ unsigned int type;
+ int unit;
+ u8 mode;
+
+ /* we always use the 0 slot for crap hardware */
+ unit = dev->devno;
+ if (!(gtm->flags & 0x10))
+ unit = 0;
+
+ /* PIO */
+ mode = ata_timing_cycle2mode(ATA_SHIFT_PIO, gtm->drive[unit].pio);
+ xfer_mask |= ata_xfer_mode2mask(mode);
+
+ /* See if we have MWDMA or UDMA data. We don't bother with
+ * MWDMA if UDMA is available as this means the BIOS set UDMA
+ * and our error changedown if it works is UDMA to PIO anyway.
+ */
+ if (!(gtm->flags & (1 << (2 * unit))))
+ type = ATA_SHIFT_MWDMA;
+ else
+ type = ATA_SHIFT_UDMA;
+
+ mode = ata_timing_cycle2mode(type, gtm->drive[unit].dma);
+ xfer_mask |= ata_xfer_mode2mask(mode);
+
+ return xfer_mask;
+}
+EXPORT_SYMBOL_GPL(ata_acpi_gtm_xfermask);
+
+/**
* ata_acpi_cbl_80wire - Check for 80 wire cable
* @ap: Port to check
+ * @gtm: GTM data to use
*
- * Return 1 if the ACPI mode data for this port indicates the BIOS selected
- * an 80wire mode.
+ * Return 1 if the @gtm indicates the BIOS selected an 80wire mode.
*/
-
-int ata_acpi_cbl_80wire(struct ata_port *ap)
+int ata_acpi_cbl_80wire(struct ata_port *ap, const struct ata_acpi_gtm *gtm)
{
- const struct ata_acpi_gtm *gtm = ata_acpi_init_gtm(ap);
- int valid = 0;
+ struct ata_device *dev;
- if (!gtm)
- return 0;
+ ata_link_for_each_dev(dev, &ap->link) {
+ unsigned long xfer_mask, udma_mask;
+
+ if (!ata_dev_enabled(dev))
+ continue;
+
+ xfer_mask = ata_acpi_gtm_xfermask(dev, gtm);
+ ata_unpack_xfermask(xfer_mask, NULL, NULL, &udma_mask);
+
+ if (udma_mask & ~ATA_UDMA_MASK_40C)
+ return 1;
+ }
- /* Split timing, DMA enabled */
- if ((gtm->flags & 0x11) == 0x11 && gtm->drive[0].dma < 55)
- valid |= 1;
- if ((gtm->flags & 0x14) == 0x14 && gtm->drive[1].dma < 55)
- valid |= 2;
- /* Shared timing, DMA enabled */
- if ((gtm->flags & 0x11) == 0x01 && gtm->drive[0].dma < 55)
- valid |= 1;
- if ((gtm->flags & 0x14) == 0x04 && gtm->drive[0].dma < 55)
- valid |= 2;
-
- /* Drive check */
- if ((valid & 1) && ata_dev_enabled(&ap->link.device[0]))
- return 1;
- if ((valid & 2) && ata_dev_enabled(&ap->link.device[1]))
- return 1;
return 0;
}
-
EXPORT_SYMBOL_GPL(ata_acpi_cbl_80wire);
static void ata_acpi_gtf_to_tf(struct ata_device *dev,
@@ -776,6 +813,36 @@ void ata_acpi_on_resume(struct ata_port *ap)
}
/**
+ * ata_acpi_set_state - set the port power state
+ * @ap: target ATA port
+ * @state: state, on/off
+ *
+ * This function executes the _PS0/_PS3 ACPI method to set the power state.
+ * ACPI spec requires _PS0 when IDE power on and _PS3 when power off
+ */
+void ata_acpi_set_state(struct ata_port *ap, pm_message_t state)
+{
+ struct ata_device *dev;
+
+ if (!ap->acpi_handle || (ap->flags & ATA_FLAG_ACPI_SATA))
+ return;
+
+ /* channel first and then drives for power on and vica versa
+ for power off */
+ if (state.event == PM_EVENT_ON)
+ acpi_bus_set_power(ap->acpi_handle, ACPI_STATE_D0);
+
+ ata_link_for_each_dev(dev, &ap->link) {
+ if (dev->acpi_handle && ata_dev_enabled(dev))
+ acpi_bus_set_power(dev->acpi_handle,
+ state.event == PM_EVENT_ON ?
+ ACPI_STATE_D0 : ACPI_STATE_D3);
+ }
+ if (state.event != PM_EVENT_ON)
+ acpi_bus_set_power(ap->acpi_handle, ACPI_STATE_D3);
+}
+
+/**
* ata_acpi_on_devcfg - ATA ACPI hook called on device donfiguration
* @dev: target ATA device
*
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 6380726..ce803d1 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -119,6 +119,10 @@ int libata_noacpi = 0;
module_param_named(noacpi, libata_noacpi, int, 0444);
MODULE_PARM_DESC(noacpi, "Disables the use of ACPI in probe/suspend/resume when set");
+int libata_allow_tpm = 0;
+module_param_named(allow_tpm, libata_allow_tpm, int, 0444);
+MODULE_PARM_DESC(allow_tpm, "Permit the use of TPM commands");
+
MODULE_AUTHOR("Jeff Garzik");
MODULE_DESCRIPTION("Library module for ATA devices");
MODULE_LICENSE("GPL");
@@ -450,9 +454,9 @@ int ata_build_rw_tf(struct ata_taskfile *tf, struct ata_device *dev,
* RETURNS:
* Packed xfer_mask.
*/
-static unsigned int ata_pack_xfermask(unsigned int pio_mask,
- unsigned int mwdma_mask,
- unsigned int udma_mask)
+unsigned long ata_pack_xfermask(unsigned long pio_mask,
+ unsigned long mwdma_mask,
+ unsigned long udma_mask)
{
return ((pio_mask << ATA_SHIFT_PIO) & ATA_MASK_PIO) |
((mwdma_mask << ATA_SHIFT_MWDMA) & ATA_MASK_MWDMA) |
@@ -469,10 +473,8 @@ static unsigned int ata_pack_xfermask(unsigned int pio_mask,
* Unpack @xfer_mask into @pio_mask, @mwdma_mask and @udma_mask.
* Any NULL distination masks will be ignored.
*/
-static void ata_unpack_xfermask(unsigned int xfer_mask,
- unsigned int *pio_mask,
- unsigned int *mwdma_mask,
- unsigned int *udma_mask)
+void ata_unpack_xfermask(unsigned long xfer_mask, unsigned long *pio_mask,
+ unsigned long *mwdma_mask, unsigned long *udma_mask)
{
if (pio_mask)
*pio_mask = (xfer_mask & ATA_MASK_PIO) >> ATA_SHIFT_PIO;
@@ -486,9 +488,9 @@ static const struct ata_xfer_ent {
int shift, bits;
u8 base;
} ata_xfer_tbl[] = {
- { ATA_SHIFT_PIO, ATA_BITS_PIO, XFER_PIO_0 },
- { ATA_SHIFT_MWDMA, ATA_BITS_MWDMA, XFER_MW_DMA_0 },
- { ATA_SHIFT_UDMA, ATA_BITS_UDMA, XFER_UDMA_0 },
+ { ATA_SHIFT_PIO, ATA_NR_PIO_MODES, XFER_PIO_0 },
+ { ATA_SHIFT_MWDMA, ATA_NR_MWDMA_MODES, XFER_MW_DMA_0 },
+ { ATA_SHIFT_UDMA, ATA_NR_UDMA_MODES, XFER_UDMA_0 },
{ -1, },
};
@@ -503,9 +505,9 @@ static const struct ata_xfer_ent {
* None.
*
* RETURNS:
- * Matching XFER_* value, 0 if no match found.
+ * Matching XFER_* value, 0xff if no match found.
*/
-static u8 ata_xfer_mask2mode(unsigned int xfer_mask)
+u8 ata_xfer_mask2mode(unsigned long xfer_mask)
{
int highbit = fls(xfer_mask) - 1;
const struct ata_xfer_ent *ent;
@@ -513,7 +515,7 @@ static u8 ata_xfer_mask2mode(unsigned int xfer_mask)
for (ent = ata_xfer_tbl; ent->shift >= 0; ent++)
if (highbit >= ent->shift && highbit < ent->shift + ent->bits)
return ent->base + highbit - ent->shift;
- return 0;
+ return 0xff;
}
/**
@@ -528,13 +530,14 @@ static u8 ata_xfer_mask2mode(unsigned int xfer_mask)
* RETURNS:
* Matching xfer_mask, 0 if no match found.
*/
-static unsigned int ata_xfer_mode2mask(u8 xfer_mode)
+unsigned long ata_xfer_mode2mask(u8 xfer_mode)
{
const struct ata_xfer_ent *ent;
for (ent = ata_xfer_tbl; ent->shift >= 0; ent++)
if (xfer_mode >= ent->base && xfer_mode < ent->base + ent->bits)
- return 1 << (ent->shift + xfer_mode - ent->base);
+ return ((2 << (ent->shift + xfer_mode - ent->base)) - 1)
+ & ~((1 << ent->shift) - 1);
return 0;
}
@@ -550,7 +553,7 @@ static unsigned int ata_xfer_mode2mask(u8 xfer_mode)
* RETURNS:
* Matching xfer_shift, -1 if no match found.
*/
-static int ata_xfer_mode2shift(unsigned int xfer_mode)
+int ata_xfer_mode2shift(unsigned long xfer_mode)
{
const struct ata_xfer_ent *ent;
@@ -574,7 +577,7 @@ static int ata_xfer_mode2shift(unsigned int xfer_mode)
* Constant C string representing highest speed listed in
* @mode_mask, or the constant C string "<n/a>".
*/
-static const char *ata_mode_string(unsigned int xfer_mask)
+const char *ata_mode_string(unsigned long xfer_mask)
{
static const char * const xfer_mode_str[] = {
"PIO0",
@@ -947,8 +950,8 @@ unsigned int ata_dev_try_classify(struct ata_device *dev, int present,
if (r_err)
*r_err = err;
- /* see if device passed diags: if master then continue and warn later */
- if (err == 0 && dev->devno == 0)
+ /* see if device passed diags: continue and warn later */
+ if (err == 0)
/* diagnostic fail : do nothing _YET_ */
dev->horkage |= ATA_HORKAGE_DIAGNOSTIC;
else if (err == 1)
@@ -1286,48 +1289,6 @@ static int ata_hpa_resize(struct ata_device *dev)
}
/**
- * ata_id_to_dma_mode - Identify DMA mode from id block
- * @dev: device to identify
- * @unknown: mode to assume if we cannot tell
- *
- * Set up the timing values for the device based upon the identify
- * reported values for the DMA mode. This function is used by drivers
- * which rely upon firmware configured modes, but wish to report the
- * mode correctly when possible.
- *
- * In addition we emit similarly formatted messages to the default
- * ata_dev_set_mode handler, in order to provide consistency of
- * presentation.
- */
-
-void ata_id_to_dma_mode(struct ata_device *dev, u8 unknown)
-{
- unsigned int mask;
- u8 mode;
-
- /* Pack the DMA modes */
- mask = ((dev->id[63] >> 8) << ATA_SHIFT_MWDMA) & ATA_MASK_MWDMA;
- if (dev->id[53] & 0x04)
- mask |= ((dev->id[88] >> 8) << ATA_SHIFT_UDMA) & ATA_MASK_UDMA;
-
- /* Select the mode in use */
- mode = ata_xfer_mask2mode(mask);
-
- if (mode != 0) {
- ata_dev_printk(dev, KERN_INFO, "configured for %s\n",
- ata_mode_string(mask));
- } else {
- /* SWDMA perhaps ? */
- mode = unknown;
- ata_dev_printk(dev, KERN_INFO, "configured for DMA\n");
- }
-
- /* Configure the device reporting */
- dev->xfer_mode = mode;
- dev->xfer_shift = ata_xfer_mode2shift(mode);
-}
-
-/**
* ata_noop_dev_select - Select device 0/1 on ATA bus
* @ap: ATA channel to manipulate
* @device: ATA device (numbered from zero) to select
@@ -1464,9 +1425,9 @@ static inline void ata_dump_id(const u16 *id)
* RETURNS:
* Computed xfermask
*/
-static unsigned int ata_id_xfermask(const u16 *id)
+unsigned long ata_id_xfermask(const u16 *id)
{
- unsigned int pio_mask, mwdma_mask, udma_mask;
+ unsigned long pio_mask, mwdma_mask, udma_mask;
/* Usual case. Word 53 indicates word 64 is valid */
if (id[ATA_ID_FIELD_VALID] & (1 << 1)) {
@@ -1519,7 +1480,7 @@ static unsigned int ata_id_xfermask(const u16 *id)
}
/**
- * ata_port_queue_task - Queue port_task
+ * ata_pio_queue_task - Queue port_task
* @ap: The ata_port to queue port_task for
* @fn: workqueue function to be scheduled
* @data: data for @fn to use
@@ -1531,16 +1492,15 @@ static unsigned int ata_id_xfermask(const u16 *id)
* one task is active at any given time.
*
* libata core layer takes care of synchronization between
- * port_task and EH. ata_port_queue_task() may be ignored for EH
+ * port_task and EH. ata_pio_queue_task() may be ignored for EH
* synchronization.
*
* LOCKING:
* Inherited from caller.
*/
-void ata_port_queue_task(struct ata_port *ap, work_func_t fn, void *data,
- unsigned long delay)
+static void ata_pio_queue_task(struct ata_port *ap, void *data,
+ unsigned long delay)
{
- PREPARE_DELAYED_WORK(&ap->port_task, fn);
ap->port_task_data = data;
/* may fail if ata_port_flush_task() in progress */
@@ -2090,7 +2050,7 @@ int ata_dev_configure(struct ata_device *dev)
struct ata_eh_context *ehc = &dev->link->eh_context;
int print_info = ehc->i.flags & ATA_EHI_PRINTINFO;
const u16 *id = dev->id;
- unsigned int xfer_mask;
+ unsigned long xfer_mask;
char revbuf[7]; /* XYZ-99\0 */
char fwrevbuf[ATA_ID_FW_REV_LEN+1];
char modelbuf[ATA_ID_PROD_LEN+1];
@@ -2161,8 +2121,14 @@ int ata_dev_configure(struct ata_device *dev)
"supports DRM functions and may "
"not be fully accessable.\n");
snprintf(revbuf, 7, "CFA");
- } else
+ } else {
snprintf(revbuf, 7, "ATA-%d", ata_id_major_version(id));
+ /* Warn the user if the device has TPM extensions */
+ if (ata_id_has_tpm(id))
+ ata_dev_printk(dev, KERN_WARNING,
+ "supports DRM functions and may "
+ "not be fully accessable.\n");
+ }
dev->n_sectors = ata_id_n_sectors(id);
@@ -2295,19 +2261,8 @@ int ata_dev_configure(struct ata_device *dev)
dev->flags |= ATA_DFLAG_DIPM;
}
- if (dev->horkage & ATA_HORKAGE_DIAGNOSTIC) {
- /* Let the user know. We don't want to disallow opens for
- rescue purposes, or in case the vendor is just a blithering
- idiot */
- if (print_info) {
- ata_dev_printk(dev, KERN_WARNING,
-"Drive reports diagnostics failure. This may indicate a drive\n");
- ata_dev_printk(dev, KERN_WARNING,
-"fault or invalid emulation. Contact drive vendor for information.\n");
- }
- }
-
- /* limit bridge transfers to udma5, 200 sectors */
+ /* Limit PATA drive on SATA cable bridge transfers to udma5,
+ 200 sectors */
if (ata_dev_knobble(dev)) {
if (ata_msg_drv(ap) && print_info)
ata_dev_printk(dev, KERN_INFO,
@@ -2336,6 +2291,21 @@ int ata_dev_configure(struct ata_device *dev)
if (ap->ops->dev_config)
ap->ops->dev_config(dev);
+ if (dev->horkage & ATA_HORKAGE_DIAGNOSTIC) {
+ /* Let the user know. We don't want to disallow opens for
+ rescue purposes, or in case the vendor is just a blithering
+ idiot. Do this after the dev_config call as some controllers
+ with buggy firmware may want to avoid reporting false device
+ bugs */
+
+ if (print_info) {
+ ata_dev_printk(dev, KERN_WARNING,
+"Drive reports diagnostics failure. This may indicate a drive\n");
+ ata_dev_printk(dev, KERN_WARNING,
+"fault or invalid emulation. Contact drive vendor for information.\n");
+ }
+ }
+
if (ata_msg_probe(ap))
ata_dev_printk(dev, KERN_DEBUG, "%s: EXIT, drv_stat = 0x%x\n",
__FUNCTION__, ata_chk_status(ap));
@@ -2387,6 +2357,18 @@ int ata_cable_unknown(struct ata_port *ap)
}
/**
+ * ata_cable_ignore - return ignored PATA cable.
+ * @ap: port
+ *
+ * Helper method for drivers which don't use cable type to limit
+ * transfer mode.
+ */
+int ata_cable_ignore(struct ata_port *ap)
+{
+ return ATA_CBL_PATA_IGN;
+}
+
+/**
* ata_cable_sata - return SATA cable type
* @ap: port
*
@@ -2781,38 +2763,33 @@ int sata_set_spd(struct ata_link *link)
*/
static const struct ata_timing ata_timing[] = {
+/* { XFER_PIO_SLOW, 120, 290, 240, 960, 290, 240, 960, 0 }, */
+ { XFER_PIO_0, 70, 290, 240, 600, 165, 150, 600, 0 },
+ { XFER_PIO_1, 50, 290, 93, 383, 125, 100, 383, 0 },
+ { XFER_PIO_2, 30, 290, 40, 330, 100, 90, 240, 0 },
+ { XFER_PIO_3, 30, 80, 70, 180, 80, 70, 180, 0 },
+ { XFER_PIO_4, 25, 70, 25, 120, 70, 25, 120, 0 },
+ { XFER_PIO_5, 15, 65, 25, 100, 65, 25, 100, 0 },
+ { XFER_PIO_6, 10, 55, 20, 80, 55, 20, 80, 0 },
- { XFER_UDMA_6, 0, 0, 0, 0, 0, 0, 0, 15 },
- { XFER_UDMA_5, 0, 0, 0, 0, 0, 0, 0, 20 },
- { XFER_UDMA_4, 0, 0, 0, 0, 0, 0, 0, 30 },
- { XFER_UDMA_3, 0, 0, 0, 0, 0, 0, 0, 45 },
+ { XFER_SW_DMA_0, 120, 0, 0, 0, 480, 480, 960, 0 },
+ { XFER_SW_DMA_1, 90, 0, 0, 0, 240, 240, 480, 0 },
+ { XFER_SW_DMA_2, 60, 0, 0, 0, 120, 120, 240, 0 },
- { XFER_MW_DMA_4, 25, 0, 0, 0, 55, 20, 80, 0 },
+ { XFER_MW_DMA_0, 60, 0, 0, 0, 215, 215, 480, 0 },
+ { XFER_MW_DMA_1, 45, 0, 0, 0, 80, 50, 150, 0 },
+ { XFER_MW_DMA_2, 25, 0, 0, 0, 70, 25, 120, 0 },
{ XFER_MW_DMA_3, 25, 0, 0, 0, 65, 25, 100, 0 },
- { XFER_UDMA_2, 0, 0, 0, 0, 0, 0, 0, 60 },
- { XFER_UDMA_1, 0, 0, 0, 0, 0, 0, 0, 80 },
- { XFER_UDMA_0, 0, 0, 0, 0, 0, 0, 0, 120 },
+ { XFER_MW_DMA_4, 25, 0, 0, 0, 55, 20, 80, 0 },
/* { XFER_UDMA_SLOW, 0, 0, 0, 0, 0, 0, 0, 150 }, */
-
- { XFER_MW_DMA_2, 25, 0, 0, 0, 70, 25, 120, 0 },
- { XFER_MW_DMA_1, 45, 0, 0, 0, 80, 50, 150, 0 },
- { XFER_MW_DMA_0, 60, 0, 0, 0, 215, 215, 480, 0 },
-
- { XFER_SW_DMA_2, 60, 0, 0, 0, 120, 120, 240, 0 },
- { XFER_SW_DMA_1, 90, 0, 0, 0, 240, 240, 480, 0 },
- { XFER_SW_DMA_0, 120, 0, 0, 0, 480, 480, 960, 0 },
-
- { XFER_PIO_6, 10, 55, 20, 80, 55, 20, 80, 0 },
- { XFER_PIO_5, 15, 65, 25, 100, 65, 25, 100, 0 },
- { XFER_PIO_4, 25, 70, 25, 120, 70, 25, 120, 0 },
- { XFER_PIO_3, 30, 80, 70, 180, 80, 70, 180, 0 },
-
- { XFER_PIO_2, 30, 290, 40, 330, 100, 90, 240, 0 },
- { XFER_PIO_1, 50, 290, 93, 383, 125, 100, 383, 0 },
- { XFER_PIO_0, 70, 290, 240, 600, 165, 150, 600, 0 },
-
-/* { XFER_PIO_SLOW, 120, 290, 240, 960, 290, 240, 960, 0 }, */
+ { XFER_UDMA_0, 0, 0, 0, 0, 0, 0, 0, 120 },
+ { XFER_UDMA_1, 0, 0, 0, 0, 0, 0, 0, 80 },
+ { XFER_UDMA_2, 0, 0, 0, 0, 0, 0, 0, 60 },
+ { XFER_UDMA_3, 0, 0, 0, 0, 0, 0, 0, 45 },
+ { XFER_UDMA_4, 0, 0, 0, 0, 0, 0, 0, 30 },
+ { XFER_UDMA_5, 0, 0, 0, 0, 0, 0, 0, 20 },
+ { XFER_UDMA_6, 0, 0, 0, 0, 0, 0, 0, 15 },
{ 0xFF }
};
@@ -2845,14 +2822,16 @@ void ata_timing_merge(const struct ata_timing *a, const struct ata_timing *b,
if (what & ATA_TIMING_UDMA ) m->udma = max(a->udma, b->udma);
}
-static const struct ata_timing *ata_timing_find_mode(unsigned short speed)
+const struct ata_timing *ata_timing_find_mode(u8 xfer_mode)
{
- const struct ata_timing *t;
+ const struct ata_timing *t = ata_timing;
+
+ while (xfer_mode > t->mode)
+ t++;
- for (t = ata_timing; t->mode != speed; t++)
- if (t->mode == 0xFF)
- return NULL;
- return t;
+ if (xfer_mode == t->mode)
+ return t;
+ return NULL;
}
int ata_timing_compute(struct ata_device *adev, unsigned short speed,
@@ -2927,6 +2906,57 @@ int ata_timing_compute(struct ata_device *adev, unsigned short speed,
}
/**
+ * ata_timing_cycle2mode - find xfer mode for the specified cycle duration
+ * @xfer_shift: ATA_SHIFT_* value for transfer type to examine.
+ * @cycle: cycle duration in ns
+ *
+ * Return matching xfer mode for @cycle. The returned mode is of
+ * the transfer type specified by @xfer_shift. If @cycle is too
+ * slow for @xfer_shift, 0xff is returned. If @cycle is faster
+ * than the fastest known mode, the fasted mode is returned.
+ *
+ * LOCKING:
+ * None.
+ *
+ * RETURNS:
+ * Matching xfer_mode, 0xff if no match found.
+ */
+u8 ata_timing_cycle2mode(unsigned int xfer_shift, int cycle)
+{
+ u8 base_mode = 0xff, last_mode = 0xff;
+ const struct ata_xfer_ent *ent;
+ const struct ata_timing *t;
+
+ for (ent = ata_xfer_tbl; ent->shift >= 0; ent++)
+ if (ent->shift == xfer_shift)
+ base_mode = ent->base;
+
+ for (t = ata_timing_find_mode(base_mode);
+ t && ata_xfer_mode2shift(t->mode) == xfer_shift; t++) {
+ unsigned short this_cycle;
+
+ switch (xfer_shift) {
+ case ATA_SHIFT_PIO:
+ case ATA_SHIFT_MWDMA:
+ this_cycle = t->cycle;
+ break;
+ case ATA_SHIFT_UDMA:
+ this_cycle = t->udma;
+ break;
+ default:
+ return 0xff;
+ }
+
+ if (cycle > this_cycle)
+ break;
+
+ last_mode = t->mode;
+ }
+
+ return last_mode;
+}
+
+/**
* ata_down_xfermask_limit - adjust dev xfer masks downward
* @dev: Device to adjust xfer masks
* @sel: ATA_DNXFER_* selector
@@ -2944,8 +2974,8 @@ int ata_timing_compute(struct ata_device *adev, unsigned short speed,
int ata_down_xfermask_limit(struct ata_device *dev, unsigned int sel)
{
char buf[32];
- unsigned int orig_mask, xfer_mask;
- unsigned int pio_mask, mwdma_mask, udma_mask;
+ unsigned long orig_mask, xfer_mask;
+ unsigned long pio_mask, mwdma_mask, udma_mask;
int quiet, highbit;
quiet = !!(sel & ATA_DNXFER_QUIET);
@@ -3039,7 +3069,7 @@ static int ata_dev_set_mode(struct ata_device *dev)
/* Early MWDMA devices do DMA but don't allow DMA mode setting.
Don't fail an MWDMA0 set IFF the device indicates it is in MWDMA0 */
- if (dev->xfer_shift == ATA_SHIFT_MWDMA &&
+ if (dev->xfer_shift == ATA_SHIFT_MWDMA &&
dev->dma_mode == XFER_MW_DMA_0 &&
(dev->id[63] >> 8) & 1)
err_mask &= ~AC_ERR_DEV;
@@ -3089,7 +3119,7 @@ int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev)
/* step 1: calculate xfer_mask */
ata_link_for_each_dev(dev, link) {
- unsigned int pio_mask, dma_mask;
+ unsigned long pio_mask, dma_mask;
unsigned int mode_mask;
if (!ata_dev_enabled(dev))
@@ -3115,7 +3145,7 @@ int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev)
dev->dma_mode = ata_xfer_mask2mode(dma_mask);
found = 1;
- if (dev->dma_mode)
+ if (dev->dma_mode != 0xff)
used_dma = 1;
}
if (!found)
@@ -3126,7 +3156,7 @@ int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev)
if (!ata_dev_enabled(dev))
continue;
- if (!dev->pio_mode) {
+ if (dev->pio_mode == 0xff) {
ata_dev_printk(dev, KERN_WARNING, "no PIO support\n");
rc = -EINVAL;
goto out;
@@ -3140,7 +3170,7 @@ int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev)
/* step 3: set host DMA timings */
ata_link_for_each_dev(dev, link) {
- if (!ata_dev_enabled(dev) || !dev->dma_mode)
+ if (!ata_dev_enabled(dev) || dev->dma_mode == 0xff)
continue;
dev->xfer_mode = dev->dma_mode;
@@ -3173,31 +3203,6 @@ int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev)
}
/**
- * ata_set_mode - Program timings and issue SET FEATURES - XFER
- * @link: link on which timings will be programmed
- * @r_failed_dev: out paramter for failed device
- *
- * Set ATA device disk transfer mode (PIO3, UDMA6, etc.). If
- * ata_set_mode() fails, pointer to the failing device is
- * returned in @r_failed_dev.
- *
- * LOCKING:
- * PCI/etc. bus probe sem.
- *
- * RETURNS:
- * 0 on success, negative errno otherwise
- */
-int ata_set_mode(struct ata_link *link, struct ata_device **r_failed_dev)
-{
- struct ata_port *ap = link->ap;
-
- /* has private set_mode? */
- if (ap->ops->set_mode)
- return ap->ops->set_mode(link, r_failed_dev);
- return ata_do_set_mode(link, r_failed_dev);
-}
-
-/**
* ata_tf_to_host - issue ATA taskfile to host controller
* @ap: port to which command is being issued
* @tf: ATA taskfile register set
@@ -4363,7 +4368,14 @@ static unsigned int ata_dev_set_xfermode(struct ata_device *dev)
tf.feature = SETFEATURES_XFER;
tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE | ATA_TFLAG_POLLING;
tf.protocol = ATA_PROT_NODATA;
- tf.nsect = dev->xfer_mode;
+ /* If we are using IORDY we must send the mode setting command */
+ if (ata_pio_need_iordy(dev))
+ tf.nsect = dev->xfer_mode;
+ /* If the device has IORDY and the controller does not - turn it off */
+ else if (ata_id_has_iordy(dev->id))
+ tf.nsect = 0x01;
+ else /* In the ancient relic department - skip all of this */
+ return 0;
err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
@@ -4462,17 +4474,13 @@ static unsigned int ata_dev_init_params(struct ata_device *dev,
void ata_sg_clean(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
- struct scatterlist *sg = qc->__sg;
+ struct scatterlist *sg = qc->sg;
int dir = qc->dma_dir;
void *pad_buf = NULL;
- WARN_ON(!(qc->flags & ATA_QCFLAG_DMAMAP));
WARN_ON(sg == NULL);
- if (qc->flags & ATA_QCFLAG_SINGLE)
- WARN_ON(qc->n_elem > 1);
-
- VPRINTK("unmapping %u sg elements\n", qc->n_elem);
+ VPRINTK("unmapping %u sg elements\n", qc->mapped_n_elem);
/* if we padded the buffer out to 32-bit bound, and data
* xfer direction is from-device, we must copy from the
@@ -4481,31 +4489,20 @@ void ata_sg_clean(struct ata_queued_cmd *qc)
if (qc->pad_len && !(qc->tf.flags & ATA_TFLAG_WRITE))
pad_buf = ap->pad + (qc->tag * ATA_DMA_PAD_SZ);
- if (qc->flags & ATA_QCFLAG_SG) {
- if (qc->n_elem)
- dma_unmap_sg(ap->dev, sg, qc->n_elem, dir);
- /* restore last sg */
- sg_last(sg, qc->orig_n_elem)->length += qc->pad_len;
- if (pad_buf) {
- struct scatterlist *psg = &qc->pad_sgent;
- void *addr = kmap_atomic(sg_page(psg), KM_IRQ0);
- memcpy(addr + psg->offset, pad_buf, qc->pad_len);
- kunmap_atomic(addr, KM_IRQ0);
- }
- } else {
- if (qc->n_elem)
- dma_unmap_single(ap->dev,
- sg_dma_address(&sg[0]), sg_dma_len(&sg[0]),
- dir);
- /* restore sg */
- sg->length += qc->pad_len;
- if (pad_buf)
- memcpy(qc->buf_virt + sg->length - qc->pad_len,
- pad_buf, qc->pad_len);
+ if (qc->mapped_n_elem)
+ dma_unmap_sg(ap->dev, sg, qc->mapped_n_elem, dir);
+ /* restore last sg */
+ if (qc->last_sg)
+ *qc->last_sg = qc->saved_last_sg;
+ if (pad_buf) {
+ struct scatterlist *psg = &qc->extra_sg[1];
+ void *addr = kmap_atomic(sg_page(psg), KM_IRQ0);
+ memcpy(addr + psg->offset, pad_buf, qc->pad_len);
+ kunmap_atomic(addr, KM_IRQ0);
}
qc->flags &= ~ATA_QCFLAG_DMAMAP;
- qc->__sg = NULL;
+ qc->sg = NULL;
}
/**
@@ -4523,13 +4520,10 @@ static void ata_fill_sg(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct scatterlist *sg;
- unsigned int idx;
+ unsigned int si, pi;
- WARN_ON(qc->__sg == NULL);
- WARN_ON(qc->n_elem == 0 && qc->pad_len == 0);
-
- idx = 0;
- ata_for_each_sg(sg, qc) {
+ pi = 0;
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
u32 addr, offset;
u32 sg_len, len;
@@ -4546,18 +4540,17 @@ static void ata_fill_sg(struct ata_queued_cmd *qc)
if ((offset + sg_len) > 0x10000)
len = 0x10000 - offset;
- ap->prd[idx].addr = cpu_to_le32(addr);
- ap->prd[idx].flags_len = cpu_to_le32(len & 0xffff);
- VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", idx, addr, len);
+ ap->prd[pi].addr = cpu_to_le32(addr);
+ ap->prd[pi].flags_len = cpu_to_le32(len & 0xffff);
+ VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", pi, addr, len);
- idx++;
+ pi++;
sg_len -= len;
addr += len;
}
}
- if (idx)
- ap->prd[idx - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
+ ap->prd[pi - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
}
/**
@@ -4577,13 +4570,10 @@ static void ata_fill_sg_dumb(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct scatterlist *sg;
- unsigned int idx;
-
- WARN_ON(qc->__sg == NULL);
- WARN_ON(qc->n_elem == 0 && qc->pad_len == 0);
+ unsigned int si, pi;
- idx = 0;
- ata_for_each_sg(sg, qc) {
+ pi = 0;
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
u32 addr, offset;
u32 sg_len, len, blen;
@@ -4601,25 +4591,24 @@ static void ata_fill_sg_dumb(struct ata_queued_cmd *qc)
len = 0x10000 - offset;
blen = len & 0xffff;
- ap->prd[idx].addr = cpu_to_le32(addr);
+ ap->prd[pi].addr = cpu_to_le32(addr);
if (blen == 0) {
/* Some PATA chipsets like the CS5530 can't
cope with 0x0000 meaning 64K as the spec says */
- ap->prd[idx].flags_len = cpu_to_le32(0x8000);
+ ap->prd[pi].flags_len = cpu_to_le32(0x8000);
blen = 0x8000;
- ap->prd[++idx].addr = cpu_to_le32(addr + 0x8000);
+ ap->prd[++pi].addr = cpu_to_le32(addr + 0x8000);
}
- ap->prd[idx].flags_len = cpu_to_le32(blen);
- VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", idx, addr, len);
+ ap->prd[pi].flags_len = cpu_to_le32(blen);
+ VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", pi, addr, len);
- idx++;
+ pi++;
sg_len -= len;
addr += len;
}
}
- if (idx)
- ap->prd[idx - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
+ ap->prd[pi - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
}
/**
@@ -4669,8 +4658,8 @@ int ata_check_atapi_dma(struct ata_queued_cmd *qc)
*/
static int atapi_qc_may_overflow(struct ata_queued_cmd *qc)
{
- if (qc->tf.protocol != ATA_PROT_ATAPI &&
- qc->tf.protocol != ATA_PROT_ATAPI_DMA)
+ if (qc->tf.protocol != ATAPI_PROT_PIO &&
+ qc->tf.protocol != ATAPI_PROT_DMA)
return 0;
if (qc->tf.flags & ATA_TFLAG_WRITE)
@@ -4756,33 +4745,6 @@ void ata_dumb_qc_prep(struct ata_queued_cmd *qc)
void ata_noop_qc_prep(struct ata_queued_cmd *qc) { }
/**
- * ata_sg_init_one - Associate command with memory buffer
- * @qc: Command to be associated
- * @buf: Memory buffer
- * @buflen: Length of memory buffer, in bytes.
- *
- * Initialize the data-related elements of queued_cmd @qc
- * to point to a single memory buffer, @buf of byte length @buflen.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- */
-
-void ata_sg_init_one(struct ata_queued_cmd *qc, void *buf, unsigned int buflen)
-{
- qc->flags |= ATA_QCFLAG_SINGLE;
-
- qc->__sg = &qc->sgent;
- qc->n_elem = 1;
- qc->orig_n_elem = 1;
- qc->buf_virt = buf;
- qc->nbytes = buflen;
- qc->cursg = qc->__sg;
-
- sg_init_one(&qc->sgent, buf, buflen);
-}
-
-/**
* ata_sg_init - Associate command with scatter-gather table.
* @qc: Command to be associated
* @sg: Scatter-gather table.
@@ -4795,84 +4757,103 @@ void ata_sg_init_one(struct ata_queued_cmd *qc, void *buf, unsigned int buflen)
* LOCKING:
* spin_lock_irqsave(host lock)
*/
-
void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
unsigned int n_elem)
{
- qc->flags |= ATA_QCFLAG_SG;
- qc->__sg = sg;
+ qc->sg = sg;
qc->n_elem = n_elem;
- qc->orig_n_elem = n_elem;
- qc->cursg = qc->__sg;
+ qc->cursg = qc->sg;
}
-/**
- * ata_sg_setup_one - DMA-map the memory buffer associated with a command.
- * @qc: Command with memory buffer to be mapped.
- *
- * DMA-map the memory buffer associated with queued_cmd @qc.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- *
- * RETURNS:
- * Zero on success, negative on error.
- */
-
-static int ata_sg_setup_one(struct ata_queued_cmd *qc)
+static unsigned int ata_sg_setup_extra(struct ata_queued_cmd *qc,
+ unsigned int *n_elem_extra,
+ unsigned int *nbytes_extra)
{
struct ata_port *ap = qc->ap;
- int dir = qc->dma_dir;
- struct scatterlist *sg = qc->__sg;
- dma_addr_t dma_address;
- int trim_sg = 0;
+ unsigned int n_elem = qc->n_elem;
+ struct scatterlist *lsg, *copy_lsg = NULL, *tsg = NULL, *esg = NULL;
+
+ *n_elem_extra = 0;
+ *nbytes_extra = 0;
+
+ /* needs padding? */
+ qc->pad_len = qc->nbytes & 3;
+
+ if (likely(!qc->pad_len))
+ return n_elem;
+
+ /* locate last sg and save it */
+ lsg = sg_last(qc->sg, n_elem);
+ qc->last_sg = lsg;
+ qc->saved_last_sg = *lsg;
+
+ sg_init_table(qc->extra_sg, ARRAY_SIZE(qc->extra_sg));
- /* we must lengthen transfers to end on a 32-bit boundary */
- qc->pad_len = sg->length & 3;
if (qc->pad_len) {
+ struct scatterlist *psg = &qc->extra_sg[1];
void *pad_buf = ap->pad + (qc->tag * ATA_DMA_PAD_SZ);
- struct scatterlist *psg = &qc->pad_sgent;
+ unsigned int offset;
WARN_ON(qc->dev->class != ATA_DEV_ATAPI);
memset(pad_buf, 0, ATA_DMA_PAD_SZ);
- if (qc->tf.flags & ATA_TFLAG_WRITE)
- memcpy(pad_buf, qc->buf_virt + sg->length - qc->pad_len,
- qc->pad_len);
+ /* psg->page/offset are used to copy to-be-written
+ * data in this function or read data in ata_sg_clean.
+ */
+ offset = lsg->offset + lsg->length - qc->pad_len;
+ sg_set_page(psg, nth_page(sg_page(lsg), offset >> PAGE_SHIFT),
+ qc->pad_len, offset_in_page(offset));
+
+ if (qc->tf.flags & ATA_TFLAG_WRITE) {
+ void *addr = kmap_atomic(sg_page(psg), KM_IRQ0);
+ memcpy(pad_buf, addr + psg->offset, qc->pad_len);
+ kunmap_atomic(addr, KM_IRQ0);
+ }
sg_dma_address(psg) = ap->pad_dma + (qc->tag * ATA_DMA_PAD_SZ);
sg_dma_len(psg) = ATA_DMA_PAD_SZ;
- /* trim sg */
- sg->length -= qc->pad_len;
- if (sg->length == 0)
- trim_sg = 1;
- DPRINTK("padding done, sg->length=%u pad_len=%u\n",
- sg->length, qc->pad_len);
- }
+ /* Trim the last sg entry and chain the original and
+ * padding sg lists.
+ *
+ * Because chaining consumes one sg entry, one extra
+ * sg entry is allocated and the last sg entry is
+ * copied to it if the length isn't zero after padded
+ * amount is removed.
+ *
+ * If the last sg entry is completely replaced by
+ * padding sg entry, the first sg entry is skipped
+ * while chaining.
+ */
+ lsg->length -= qc->pad_len;
+ if (lsg->length) {
+ copy_lsg = &qc->extra_sg[0];
+ tsg = &qc->extra_sg[0];
+ } else {
+ n_elem--;
+ tsg = &qc->extra_sg[1];
+ }
- if (trim_sg) {
- qc->n_elem--;
- goto skip_map;
- }
+ esg = &qc->extra_sg[1];
- dma_address = dma_map_single(ap->dev, qc->buf_virt,
- sg->length, dir);
- if (dma_mapping_error(dma_address)) {
- /* restore sg */
- sg->length += qc->pad_len;
- return -1;
+ (*n_elem_extra)++;
+ (*nbytes_extra) += 4 - qc->pad_len;
}
- sg_dma_address(sg) = dma_address;
- sg_dma_len(sg) = sg->length;
+ if (copy_lsg)
+ sg_set_page(copy_lsg, sg_page(lsg), lsg->length, lsg->offset);
-skip_map:
- DPRINTK("mapped buffer of %d bytes for %s\n", sg_dma_len(sg),
- qc->tf.flags & ATA_TFLAG_WRITE ? "write" : "read");
+ sg_chain(lsg, 1, tsg);
+ sg_mark_end(esg);
- return 0;
+ /* sglist can't start with chaining sg entry, fast forward */
+ if (qc->sg == lsg) {
+ qc->sg = tsg;
+ qc->cursg = tsg;
+ }
+
+ return n_elem;
}
/**
@@ -4888,75 +4869,30 @@ skip_map:
* Zero on success, negative on error.
*
*/
-
static int ata_sg_setup(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
- struct scatterlist *sg = qc->__sg;
- struct scatterlist *lsg = sg_last(qc->__sg, qc->n_elem);
- int n_elem, pre_n_elem, dir, trim_sg = 0;
+ unsigned int n_elem, n_elem_extra, nbytes_extra;
VPRINTK("ENTER, ata%u\n", ap->print_id);
- WARN_ON(!(qc->flags & ATA_QCFLAG_SG));
- /* we must lengthen transfers to end on a 32-bit boundary */
- qc->pad_len = lsg->length & 3;
- if (qc->pad_len) {
- void *pad_buf = ap->pad + (qc->tag * ATA_DMA_PAD_SZ);
- struct scatterlist *psg = &qc->pad_sgent;
- unsigned int offset;
-
- WARN_ON(qc->dev->class != ATA_DEV_ATAPI);
+ n_elem = ata_sg_setup_extra(qc, &n_elem_extra, &nbytes_extra);
- memset(pad_buf, 0, ATA_DMA_PAD_SZ);
-
- /*
- * psg->page/offset are used to copy to-be-written
- * data in this function or read data in ata_sg_clean.
- */
- offset = lsg->offset + lsg->length - qc->pad_len;
- sg_init_table(psg, 1);
- sg_set_page(psg, nth_page(sg_page(lsg), offset >> PAGE_SHIFT),
- qc->pad_len, offset_in_page(offset));
-
- if (qc->tf.flags & ATA_TFLAG_WRITE) {
- void *addr = kmap_atomic(sg_page(psg), KM_IRQ0);
- memcpy(pad_buf, addr + psg->offset, qc->pad_len);
- kunmap_atomic(addr, KM_IRQ0);
+ if (n_elem) {
+ n_elem = dma_map_sg(ap->dev, qc->sg, n_elem, qc->dma_dir);
+ if (n_elem < 1) {
+ /* restore last sg */
+ if (qc->last_sg)
+ *qc->last_sg = qc->saved_last_sg;
+ return -1;
}
-
- sg_dma_address(psg) = ap->pad_dma + (qc->tag * ATA_DMA_PAD_SZ);
- sg_dma_len(psg) = ATA_DMA_PAD_SZ;
- /* trim last sg */
- lsg->length -= qc->pad_len;
- if (lsg->length == 0)
- trim_sg = 1;
-
- DPRINTK("padding done, sg[%d].length=%u pad_len=%u\n",
- qc->n_elem - 1, lsg->length, qc->pad_len);
- }
-
- pre_n_elem = qc->n_elem;
- if (trim_sg && pre_n_elem)
- pre_n_elem--;
-
- if (!pre_n_elem) {
- n_elem = 0;
- goto skip_map;
- }
-
- dir = qc->dma_dir;
- n_elem = dma_map_sg(ap->dev, sg, pre_n_elem, dir);
- if (n_elem < 1) {
- /* restore last sg */
- lsg->length += qc->pad_len;
- return -1;
+ DPRINTK("%d sg elements mapped\n", n_elem);
}
- DPRINTK("%d sg elements mapped\n", n_elem);
-
-skip_map:
- qc->n_elem = n_elem;
+ qc->n_elem = qc->mapped_n_elem = n_elem;
+ qc->n_elem += n_elem_extra;
+ qc->nbytes += nbytes_extra;
+ qc->flags |= ATA_QCFLAG_DMAMAP;
return 0;
}
@@ -4985,7 +4921,7 @@ void swap_buf_le16(u16 *buf, unsigned int buf_words)
/**
* ata_data_xfer - Transfer data by PIO
- * @adev: device to target
+ * @dev: device to target
* @buf: data buffer
* @buflen: buffer length
* @write_data: read/write
@@ -4994,37 +4930,44 @@ void swap_buf_le16(u16 *buf, unsigned int buf_words)
*
* LOCKING:
* Inherited from caller.
+ *
+ * RETURNS:
+ * Bytes consumed.
*/
-void ata_data_xfer(struct ata_device *adev, unsigned char *buf,
- unsigned int buflen, int write_data)
+unsigned int ata_data_xfer(struct ata_device *dev, unsigned char *buf,
+ unsigned int buflen, int rw)
{
- struct ata_port *ap = adev->link->ap;
+ struct ata_port *ap = dev->link->ap;
+ void __iomem *data_addr = ap->ioaddr.data_addr;
unsigned int words = buflen >> 1;
/* Transfer multiple of 2 bytes */
- if (write_data)
- iowrite16_rep(ap->ioaddr.data_addr, buf, words);
+ if (rw == READ)
+ ioread16_rep(data_addr, buf, words);
else
- ioread16_rep(ap->ioaddr.data_addr, buf, words);
+ iowrite16_rep(data_addr, buf, words);
/* Transfer trailing 1 byte, if any. */
if (unlikely(buflen & 0x01)) {
- u16 align_buf[1] = { 0 };
+ __le16 align_buf[1] = { 0 };
unsigned char *trailing_buf = buf + buflen - 1;
- if (write_data) {
- memcpy(align_buf, trailing_buf, 1);
- iowrite16(le16_to_cpu(align_buf[0]), ap->ioaddr.data_addr);
- } else {
- align_buf[0] = cpu_to_le16(ioread16(ap->ioaddr.data_addr));
+ if (rw == READ) {
+ align_buf[0] = cpu_to_le16(ioread16(data_addr));
memcpy(trailing_buf, align_buf, 1);
+ } else {
+ memcpy(align_buf, trailing_buf, 1);
+ iowrite16(le16_to_cpu(align_buf[0]), data_addr);
}
+ words++;
}
+
+ return words << 1;
}
/**
* ata_data_xfer_noirq - Transfer data by PIO
- * @adev: device to target
+ * @dev: device to target
* @buf: data buffer
* @buflen: buffer length
* @write_data: read/write
@@ -5034,14 +4977,21 @@ void ata_data_xfer(struct ata_device *adev, unsigned char *buf,
*
* LOCKING:
* Inherited from caller.
+ *
+ * RETURNS:
+ * Bytes consumed.
*/
-void ata_data_xfer_noirq(struct ata_device *adev, unsigned char *buf,
- unsigned int buflen, int write_data)
+unsigned int ata_data_xfer_noirq(struct ata_device *dev, unsigned char *buf,
+ unsigned int buflen, int rw)
{
unsigned long flags;
+ unsigned int consumed;
+
local_irq_save(flags);
- ata_data_xfer(adev, buf, buflen, write_data);
+ consumed = ata_data_xfer(dev, buf, buflen, rw);
local_irq_restore(flags);
+
+ return consumed;
}
@@ -5152,13 +5102,13 @@ static void atapi_send_cdb(struct ata_port *ap, struct ata_queued_cmd *qc)
ata_altstatus(ap); /* flush */
switch (qc->tf.protocol) {
- case ATA_PROT_ATAPI:
+ case ATAPI_PROT_PIO:
ap->hsm_task_state = HSM_ST;
break;
- case ATA_PROT_ATAPI_NODATA:
+ case ATAPI_PROT_NODATA:
ap->hsm_task_state = HSM_ST_LAST;
break;
- case ATA_PROT_ATAPI_DMA:
+ case ATAPI_PROT_DMA:
ap->hsm_task_state = HSM_ST_LAST;
/* initiate bmdma */
ap->ops->bmdma_start(qc);
@@ -5300,12 +5250,15 @@ static void atapi_pio_bytes(struct ata_queued_cmd *qc)
bytes = (bc_hi << 8) | bc_lo;
/* shall be cleared to zero, indicating xfer of data */
- if (ireason & (1 << 0))
+ if (unlikely(ireason & (1 << 0)))
goto err_out;
/* make sure transfer direction matches expected */
i_write = ((ireason & (1 << 1)) == 0) ? 1 : 0;
- if (do_write != i_write)
+ if (unlikely(do_write != i_write))
+ goto err_out;
+
+ if (unlikely(!bytes))
goto err_out;
VPRINTK("ata%u: xfering %d bytes\n", ap->print_id, bytes);
@@ -5341,7 +5294,7 @@ static inline int ata_hsm_ok_in_wq(struct ata_port *ap, struct ata_queued_cmd *q
(qc->tf.flags & ATA_TFLAG_WRITE))
return 1;
- if (is_atapi_taskfile(&qc->tf) &&
+ if (ata_is_atapi(qc->tf.protocol) &&
!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
return 1;
}
@@ -5506,7 +5459,7 @@ fsm_start:
case HSM_ST:
/* complete command or read/write the data register */
- if (qc->tf.protocol == ATA_PROT_ATAPI) {
+ if (qc->tf.protocol == ATAPI_PROT_PIO) {
/* ATAPI PIO protocol */
if ((status & ATA_DRQ) == 0) {
/* No more data to transfer or device error.
@@ -5664,7 +5617,7 @@ fsm_start:
msleep(2);
status = ata_busy_wait(ap, ATA_BUSY, 10);
if (status & ATA_BUSY) {
- ata_port_queue_task(ap, ata_pio_task, qc, ATA_SHORT_PAUSE);
+ ata_pio_queue_task(ap, qc, ATA_SHORT_PAUSE);
return;
}
}
@@ -5805,6 +5758,22 @@ static void fill_result_tf(struct ata_queued_cmd *qc)
ap->ops->tf_read(ap, &qc->result_tf);
}
+static void ata_verify_xfer(struct ata_queued_cmd *qc)
+{
+ struct ata_device *dev = qc->dev;
+
+ if (ata_tag_internal(qc->tag))
+ return;
+
+ if (ata_is_nodata(qc->tf.protocol))
+ return;
+
+ if ((dev->mwdma_mask || dev->udma_mask) && ata_is_pio(qc->tf.protocol))
+ return;
+
+ dev->flags &= ~ATA_DFLAG_DUBIOUS_XFER;
+}
+
/**
* ata_qc_complete - Complete an active ATA command
* @qc: Command to complete
@@ -5876,6 +5845,9 @@ void ata_qc_complete(struct ata_queued_cmd *qc)
break;
}
+ if (unlikely(dev->flags & ATA_DFLAG_DUBIOUS_XFER))
+ ata_verify_xfer(qc);
+
__ata_qc_complete(qc);
} else {
if (qc->flags & ATA_QCFLAG_EH_SCHEDULED)
@@ -5938,30 +5910,6 @@ int ata_qc_complete_multiple(struct ata_port *ap, u32 qc_active,
return nr_done;
}
-static inline int ata_should_dma_map(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
-
- switch (qc->tf.protocol) {
- case ATA_PROT_NCQ:
- case ATA_PROT_DMA:
- case ATA_PROT_ATAPI_DMA:
- return 1;
-
- case ATA_PROT_ATAPI:
- case ATA_PROT_PIO:
- if (ap->flags & ATA_FLAG_PIO_DMA)
- return 1;
-
- /* fall through */
-
- default:
- return 0;
- }
-
- /* never reached */
-}
-
/**
* ata_qc_issue - issue taskfile to device
* @qc: command to issue to device
@@ -5978,6 +5926,7 @@ void ata_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ata_link *link = qc->dev->link;
+ u8 prot = qc->tf.protocol;
/* Make sure only one non-NCQ command is outstanding. The
* check is skipped for old EH because it reuses active qc to
@@ -5985,7 +5934,7 @@ void ata_qc_issue(struct ata_queued_cmd *qc)
*/
WARN_ON(ap->ops->error_handler && ata_tag_valid(link->active_tag));
- if (qc->tf.protocol == ATA_PROT_NCQ) {
+ if (ata_is_ncq(prot)) {
WARN_ON(link->sactive & (1 << qc->tag));
if (!link->sactive)
@@ -6001,17 +5950,18 @@ void ata_qc_issue(struct ata_queued_cmd *qc)
qc->flags |= ATA_QCFLAG_ACTIVE;
ap->qc_active |= 1 << qc->tag;
- if (ata_should_dma_map(qc)) {
- if (qc->flags & ATA_QCFLAG_SG) {
- if (ata_sg_setup(qc))
- goto sg_err;
- } else if (qc->flags & ATA_QCFLAG_SINGLE) {
- if (ata_sg_setup_one(qc))
- goto sg_err;
- }
- } else {
- qc->flags &= ~ATA_QCFLAG_DMAMAP;
- }
+ /* We guarantee to LLDs that they will have at least one
+ * non-zero sg if the command is a data command.
+ */
+ BUG_ON(ata_is_data(prot) && (!qc->sg || !qc->n_elem || !qc->nbytes));
+
+ /* ata_sg_setup() may update nbytes */
+ qc->raw_nbytes = qc->nbytes;
+
+ if (ata_is_dma(prot) || (ata_is_pio(prot) &&
+ (ap->flags & ATA_FLAG_PIO_DMA)))
+ if (ata_sg_setup(qc))
+ goto sg_err;
/* if device is sleeping, schedule softreset and abort the link */
if (unlikely(qc->dev->flags & ATA_DFLAG_SLEEPING)) {
@@ -6029,7 +5979,6 @@ void ata_qc_issue(struct ata_queued_cmd *qc)
return;
sg_err:
- qc->flags &= ~ATA_QCFLAG_DMAMAP;
qc->err_mask |= AC_ERR_SYSTEM;
err:
ata_qc_complete(qc);
@@ -6064,11 +6013,11 @@ unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc)
switch (qc->tf.protocol) {
case ATA_PROT_PIO:
case ATA_PROT_NODATA:
- case ATA_PROT_ATAPI:
- case ATA_PROT_ATAPI_NODATA:
+ case ATAPI_PROT_PIO:
+ case ATAPI_PROT_NODATA:
qc->tf.flags |= ATA_TFLAG_POLLING;
break;
- case ATA_PROT_ATAPI_DMA:
+ case ATAPI_PROT_DMA:
if (qc->dev->flags & ATA_DFLAG_CDB_INTR)
/* see ata_dma_blacklisted() */
BUG();
@@ -6091,7 +6040,7 @@ unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc)
ap->hsm_task_state = HSM_ST_LAST;
if (qc->tf.flags & ATA_TFLAG_POLLING)
- ata_port_queue_task(ap, ata_pio_task, qc, 0);
+ ata_pio_queue_task(ap, qc, 0);
break;
@@ -6113,7 +6062,7 @@ unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc)
if (qc->tf.flags & ATA_TFLAG_WRITE) {
/* PIO data out protocol */
ap->hsm_task_state = HSM_ST_FIRST;
- ata_port_queue_task(ap, ata_pio_task, qc, 0);
+ ata_pio_queue_task(ap, qc, 0);
/* always send first data block using
* the ata_pio_task() codepath.
@@ -6123,7 +6072,7 @@ unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc)
ap->hsm_task_state = HSM_ST;
if (qc->tf.flags & ATA_TFLAG_POLLING)
- ata_port_queue_task(ap, ata_pio_task, qc, 0);
+ ata_pio_queue_task(ap, qc, 0);
/* if polling, ata_pio_task() handles the rest.
* otherwise, interrupt handler takes over from here.
@@ -6132,8 +6081,8 @@ unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc)
break;
- case ATA_PROT_ATAPI:
- case ATA_PROT_ATAPI_NODATA:
+ case ATAPI_PROT_PIO:
+ case ATAPI_PROT_NODATA:
if (qc->tf.flags & ATA_TFLAG_POLLING)
ata_qc_set_polling(qc);
@@ -6144,10 +6093,10 @@ unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc)
/* send cdb by polling if no cdb interrupt */
if ((!(qc->dev->flags & ATA_DFLAG_CDB_INTR)) ||
(qc->tf.flags & ATA_TFLAG_POLLING))
- ata_port_queue_task(ap, ata_pio_task, qc, 0);
+ ata_pio_queue_task(ap, qc, 0);
break;
- case ATA_PROT_ATAPI_DMA:
+ case ATAPI_PROT_DMA:
WARN_ON(qc->tf.flags & ATA_TFLAG_POLLING);
ap->ops->tf_load(ap, &qc->tf); /* load tf registers */
@@ -6156,7 +6105,7 @@ unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc)
/* send cdb by polling if no cdb interrupt */
if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
- ata_port_queue_task(ap, ata_pio_task, qc, 0);
+ ata_pio_queue_task(ap, qc, 0);
break;
default:
@@ -6200,15 +6149,15 @@ inline unsigned int ata_host_intr(struct ata_port *ap,
*/
/* Check the ATA_DFLAG_CDB_INTR flag is enough here.
- * The flag was turned on only for atapi devices.
- * No need to check is_atapi_taskfile(&qc->tf) again.
+ * The flag was turned on only for atapi devices. No
+ * need to check ata_is_atapi(qc->tf.protocol) again.
*/
if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
goto idle_irq;
break;
case HSM_ST_LAST:
if (qc->tf.protocol == ATA_PROT_DMA ||
- qc->tf.protocol == ATA_PROT_ATAPI_DMA) {
+ qc->tf.protocol == ATAPI_PROT_DMA) {
/* check status of DMA engine */
host_stat = ap->ops->bmdma_status(ap);
VPRINTK("ata%u: host_stat 0x%X\n",
@@ -6250,7 +6199,7 @@ inline unsigned int ata_host_intr(struct ata_port *ap,
ata_hsm_move(ap, qc, status, 0);
if (unlikely(qc->err_mask) && (qc->tf.protocol == ATA_PROT_DMA ||
- qc->tf.protocol == ATA_PROT_ATAPI_DMA))
+ qc->tf.protocol == ATAPI_PROT_DMA))
ata_ehi_push_desc(ehi, "BMDMA stat 0x%x", host_stat);
return 1; /* irq handled */
@@ -6772,7 +6721,7 @@ struct ata_port *ata_port_alloc(struct ata_host *host)
ap->msg_enable = ATA_MSG_DRV | ATA_MSG_ERR | ATA_MSG_WARN;
#endif
- INIT_DELAYED_WORK(&ap->port_task, NULL);
+ INIT_DELAYED_WORK(&ap->port_task, ata_pio_task);
INIT_DELAYED_WORK(&ap->hotplug_task, ata_scsi_hotplug);
INIT_WORK(&ap->scsi_rescan_task, ata_scsi_dev_rescan);
INIT_LIST_HEAD(&ap->eh_done_q);
@@ -7589,7 +7538,6 @@ EXPORT_SYMBOL_GPL(ata_host_register);
EXPORT_SYMBOL_GPL(ata_host_activate);
EXPORT_SYMBOL_GPL(ata_host_detach);
EXPORT_SYMBOL_GPL(ata_sg_init);
-EXPORT_SYMBOL_GPL(ata_sg_init_one);
EXPORT_SYMBOL_GPL(ata_hsm_move);
EXPORT_SYMBOL_GPL(ata_qc_complete);
EXPORT_SYMBOL_GPL(ata_qc_complete_multiple);
@@ -7601,6 +7549,13 @@ EXPORT_SYMBOL_GPL(ata_std_dev_select);
EXPORT_SYMBOL_GPL(sata_print_link_status);
EXPORT_SYMBOL_GPL(ata_tf_to_fis);
EXPORT_SYMBOL_GPL(ata_tf_from_fis);
+EXPORT_SYMBOL_GPL(ata_pack_xfermask);
+EXPORT_SYMBOL_GPL(ata_unpack_xfermask);
+EXPORT_SYMBOL_GPL(ata_xfer_mask2mode);
+EXPORT_SYMBOL_GPL(ata_xfer_mode2mask);
+EXPORT_SYMBOL_GPL(ata_xfer_mode2shift);
+EXPORT_SYMBOL_GPL(ata_mode_string);
+EXPORT_SYMBOL_GPL(ata_id_xfermask);
EXPORT_SYMBOL_GPL(ata_check_status);
EXPORT_SYMBOL_GPL(ata_altstatus);
EXPORT_SYMBOL_GPL(ata_exec_command);
@@ -7643,7 +7598,6 @@ EXPORT_SYMBOL_GPL(ata_wait_register);
EXPORT_SYMBOL_GPL(ata_busy_sleep);
EXPORT_SYMBOL_GPL(ata_wait_after_reset);
EXPORT_SYMBOL_GPL(ata_wait_ready);
-EXPORT_SYMBOL_GPL(ata_port_queue_task);
EXPORT_SYMBOL_GPL(ata_scsi_ioctl);
EXPORT_SYMBOL_GPL(ata_scsi_queuecmd);
EXPORT_SYMBOL_GPL(ata_scsi_slave_config);
@@ -7662,18 +7616,20 @@ EXPORT_SYMBOL_GPL(ata_host_resume);
#endif /* CONFIG_PM */
EXPORT_SYMBOL_GPL(ata_id_string);
EXPORT_SYMBOL_GPL(ata_id_c_string);
-EXPORT_SYMBOL_GPL(ata_id_to_dma_mode);
EXPORT_SYMBOL_GPL(ata_scsi_simulate);
EXPORT_SYMBOL_GPL(ata_pio_need_iordy);
+EXPORT_SYMBOL_GPL(ata_timing_find_mode);
EXPORT_SYMBOL_GPL(ata_timing_compute);
EXPORT_SYMBOL_GPL(ata_timing_merge);
+EXPORT_SYMBOL_GPL(ata_timing_cycle2mode);
#ifdef CONFIG_PCI
EXPORT_SYMBOL_GPL(pci_test_config_bits);
EXPORT_SYMBOL_GPL(ata_pci_init_sff_host);
EXPORT_SYMBOL_GPL(ata_pci_init_bmdma);
EXPORT_SYMBOL_GPL(ata_pci_prepare_sff_host);
+EXPORT_SYMBOL_GPL(ata_pci_activate_sff_host);
EXPORT_SYMBOL_GPL(ata_pci_init_one);
EXPORT_SYMBOL_GPL(ata_pci_remove_one);
#ifdef CONFIG_PM
@@ -7715,4 +7671,5 @@ EXPORT_SYMBOL_GPL(ata_dev_try_classify);
EXPORT_SYMBOL_GPL(ata_cable_40wire);
EXPORT_SYMBOL_GPL(ata_cable_80wire);
EXPORT_SYMBOL_GPL(ata_cable_unknown);
+EXPORT_SYMBOL_GPL(ata_cable_ignore);
EXPORT_SYMBOL_GPL(ata_cable_sata);
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 21a81cd..4e31071 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -46,9 +46,26 @@
#include "libata.h"
enum {
+ /* speed down verdicts */
ATA_EH_SPDN_NCQ_OFF = (1 << 0),
ATA_EH_SPDN_SPEED_DOWN = (1 << 1),
ATA_EH_SPDN_FALLBACK_TO_PIO = (1 << 2),
+ ATA_EH_SPDN_KEEP_ERRORS = (1 << 3),
+
+ /* error flags */
+ ATA_EFLAG_IS_IO = (1 << 0),
+ ATA_EFLAG_DUBIOUS_XFER = (1 << 1),
+
+ /* error categories */
+ ATA_ECAT_NONE = 0,
+ ATA_ECAT_ATA_BUS = 1,
+ ATA_ECAT_TOUT_HSM = 2,
+ ATA_ECAT_UNK_DEV = 3,
+ ATA_ECAT_DUBIOUS_NONE = 4,
+ ATA_ECAT_DUBIOUS_ATA_BUS = 5,
+ ATA_ECAT_DUBIOUS_TOUT_HSM = 6,
+ ATA_ECAT_DUBIOUS_UNK_DEV = 7,
+ ATA_ECAT_NR = 8,
};
/* Waiting in ->prereset can never be reliable. It's sometimes nice
@@ -213,12 +230,13 @@ void ata_port_pbar_desc(struct ata_port *ap, int bar, ssize_t offset,
if (offset < 0)
ata_port_desc(ap, "%s %s%llu@0x%llx", name, type, len, start);
else
- ata_port_desc(ap, "%s 0x%llx", name, start + offset);
+ ata_port_desc(ap, "%s 0x%llx", name,
+ start + (unsigned long long)offset);
}
#endif /* CONFIG_PCI */
-static void ata_ering_record(struct ata_ering *ering, int is_io,
+static void ata_ering_record(struct ata_ering *ering, unsigned int eflags,
unsigned int err_mask)
{
struct ata_ering_entry *ent;
@@ -229,11 +247,20 @@ static void ata_ering_record(struct ata_ering *ering, int is_io,
ering->cursor %= ATA_ERING_SIZE;
ent = &ering->ring[ering->cursor];
- ent->is_io = is_io;
+ ent->eflags = eflags;
ent->err_mask = err_mask;
ent->timestamp = get_jiffies_64();
}
+static struct ata_ering_entry *ata_ering_top(struct ata_ering *ering)
+{
+ struct ata_ering_entry *ent = &ering->ring[ering->cursor];
+
+ if (ent->err_mask)
+ return ent;
+ return NULL;
+}
+
static void ata_ering_clear(struct ata_ering *ering)
{
memset(ering, 0, sizeof(*ering));
@@ -445,9 +472,20 @@ void ata_scsi_error(struct Scsi_Host *host)
spin_lock_irqsave(ap->lock, flags);
__ata_port_for_each_link(link, ap) {
+ struct ata_eh_context *ehc = &link->eh_context;
+ struct ata_device *dev;
+
memset(&link->eh_context, 0, sizeof(link->eh_context));
link->eh_context.i = link->eh_info;
memset(&link->eh_info, 0, sizeof(link->eh_info));
+
+ ata_link_for_each_dev(dev, link) {
+ int devno = dev->devno;
+
+ ehc->saved_xfer_mode[devno] = dev->xfer_mode;
+ if (ata_ncq_enabled(dev))
+ ehc->saved_ncq_enabled |= 1 << devno;
+ }
}
ap->pflags |= ATA_PFLAG_EH_IN_PROGRESS;
@@ -1260,10 +1298,10 @@ static unsigned int atapi_eh_request_sense(struct ata_queued_cmd *qc)
/* is it pointless to prefer PIO for "safety reasons"? */
if (ap->flags & ATA_FLAG_PIO_DMA) {
- tf.protocol = ATA_PROT_ATAPI_DMA;
+ tf.protocol = ATAPI_PROT_DMA;
tf.feature |= ATAPI_PKT_DMA;
} else {
- tf.protocol = ATA_PROT_ATAPI;
+ tf.protocol = ATAPI_PROT_PIO;
tf.lbam = SCSI_SENSE_BUFFERSIZE;
tf.lbah = 0;
}
@@ -1451,20 +1489,29 @@ static unsigned int ata_eh_analyze_tf(struct ata_queued_cmd *qc,
return action;
}
-static int ata_eh_categorize_error(int is_io, unsigned int err_mask)
+static int ata_eh_categorize_error(unsigned int eflags, unsigned int err_mask,
+ int *xfer_ok)
{
+ int base = 0;
+
+ if (!(eflags & ATA_EFLAG_DUBIOUS_XFER))
+ *xfer_ok = 1;
+
+ if (!*xfer_ok)
+ base = ATA_ECAT_DUBIOUS_NONE;
+
if (err_mask & AC_ERR_ATA_BUS)
- return 1;
+ return base + ATA_ECAT_ATA_BUS;
if (err_mask & AC_ERR_TIMEOUT)
- return 2;
+ return base + ATA_ECAT_TOUT_HSM;
- if (is_io) {
+ if (eflags & ATA_EFLAG_IS_IO) {
if (err_mask & AC_ERR_HSM)
- return 2;
+ return base + ATA_ECAT_TOUT_HSM;
if ((err_mask &
(AC_ERR_DEV|AC_ERR_MEDIA|AC_ERR_INVALID)) == AC_ERR_DEV)
- return 3;
+ return base + ATA_ECAT_UNK_DEV;
}
return 0;
@@ -1472,18 +1519,22 @@ static int ata_eh_categorize_error(int is_io, unsigned int err_mask)
struct speed_down_verdict_arg {
u64 since;
- int nr_errors[4];
+ int xfer_ok;
+ int nr_errors[ATA_ECAT_NR];
};
static int speed_down_verdict_cb(struct ata_ering_entry *ent, void *void_arg)
{
struct speed_down_verdict_arg *arg = void_arg;
- int cat = ata_eh_categorize_error(ent->is_io, ent->err_mask);
+ int cat;
if (ent->timestamp < arg->since)
return -1;
+ cat = ata_eh_categorize_error(ent->eflags, ent->err_mask,
+ &arg->xfer_ok);
arg->nr_errors[cat]++;
+
return 0;
}
@@ -1495,22 +1546,48 @@ static int speed_down_verdict_cb(struct ata_ering_entry *ent, void *void_arg)
* whether NCQ needs to be turned off, transfer speed should be
* stepped down, or falling back to PIO is necessary.
*
- * Cat-1 is ATA_BUS error for any command.
+ * ECAT_ATA_BUS : ATA_BUS error for any command
+ *
+ * ECAT_TOUT_HSM : TIMEOUT for any command or HSM violation for
+ * IO commands
+ *
+ * ECAT_UNK_DEV : Unknown DEV error for IO commands
+ *
+ * ECAT_DUBIOUS_* : Identical to above three but occurred while
+ * data transfer hasn't been verified.
+ *
+ * Verdicts are
+ *
+ * NCQ_OFF : Turn off NCQ.
+ *
+ * SPEED_DOWN : Speed down transfer speed but don't fall back
+ * to PIO.
+ *
+ * FALLBACK_TO_PIO : Fall back to PIO.
+ *
+ * Even if multiple verdicts are returned, only one action is
+ * taken per error. An action triggered by non-DUBIOUS errors
+ * clears ering, while one triggered by DUBIOUS_* errors doesn't.
+ * This is to expedite speed down decisions right after device is
+ * initially configured.
*
- * Cat-2 is TIMEOUT for any command or HSM violation for known
- * supported commands.
+ * The followings are speed down rules. #1 and #2 deal with
+ * DUBIOUS errors.
*
- * Cat-3 is is unclassified DEV error for known supported
- * command.
+ * 1. If more than one DUBIOUS_ATA_BUS or DUBIOUS_TOUT_HSM errors
+ * occurred during last 5 mins, SPEED_DOWN and FALLBACK_TO_PIO.
*
- * NCQ needs to be turned off if there have been more than 3
- * Cat-2 + Cat-3 errors during last 10 minutes.
+ * 2. If more than one DUBIOUS_TOUT_HSM or DUBIOUS_UNK_DEV errors
+ * occurred during last 5 mins, NCQ_OFF.
*
- * Speed down is necessary if there have been more than 3 Cat-1 +
- * Cat-2 errors or 10 Cat-3 errors during last 10 minutes.
+ * 3. If more than 8 ATA_BUS, TOUT_HSM or UNK_DEV errors
+ * ocurred during last 5 mins, FALLBACK_TO_PIO
*
- * Falling back to PIO mode is necessary if there have been more
- * than 10 Cat-1 + Cat-2 + Cat-3 errors during last 5 minutes.
+ * 4. If more than 3 TOUT_HSM or UNK_DEV errors occurred
+ * during last 10 mins, NCQ_OFF.
+ *
+ * 5. If more than 3 ATA_BUS or TOUT_HSM errors, or more than 6
+ * UNK_DEV errors occurred during last 10 mins, SPEED_DOWN.
*
* LOCKING:
* Inherited from caller.
@@ -1525,23 +1602,38 @@ static unsigned int ata_eh_speed_down_verdict(struct ata_device *dev)
struct speed_down_verdict_arg arg;
unsigned int verdict = 0;
- /* scan past 10 mins of error history */
+ /* scan past 5 mins of error history */
memset(&arg, 0, sizeof(arg));
- arg.since = j64 - min(j64, j10mins);
+ arg.since = j64 - min(j64, j5mins);
ata_ering_map(&dev->ering, speed_down_verdict_cb, &arg);
- if (arg.nr_errors[2] + arg.nr_errors[3] > 3)
- verdict |= ATA_EH_SPDN_NCQ_OFF;
- if (arg.nr_errors[1] + arg.nr_errors[2] > 3 || arg.nr_errors[3] > 10)
- verdict |= ATA_EH_SPDN_SPEED_DOWN;
+ if (arg.nr_errors[ATA_ECAT_DUBIOUS_ATA_BUS] +
+ arg.nr_errors[ATA_ECAT_DUBIOUS_TOUT_HSM] > 1)
+ verdict |= ATA_EH_SPDN_SPEED_DOWN |
+ ATA_EH_SPDN_FALLBACK_TO_PIO | ATA_EH_SPDN_KEEP_ERRORS;
- /* scan past 3 mins of error history */
+ if (arg.nr_errors[ATA_ECAT_DUBIOUS_TOUT_HSM] +
+ arg.nr_errors[ATA_ECAT_DUBIOUS_UNK_DEV] > 1)
+ verdict |= ATA_EH_SPDN_NCQ_OFF | ATA_EH_SPDN_KEEP_ERRORS;
+
+ if (arg.nr_errors[ATA_ECAT_ATA_BUS] +
+ arg.nr_errors[ATA_ECAT_TOUT_HSM] +
+ arg.nr_errors[ATA_ECAT_UNK_DEV] > 6)
+ verdict |= ATA_EH_SPDN_FALLBACK_TO_PIO;
+
+ /* scan past 10 mins of error history */
memset(&arg, 0, sizeof(arg));
- arg.since = j64 - min(j64, j5mins);
+ arg.since = j64 - min(j64, j10mins);
ata_ering_map(&dev->ering, speed_down_verdict_cb, &arg);
- if (arg.nr_errors[1] + arg.nr_errors[2] + arg.nr_errors[3] > 10)
- verdict |= ATA_EH_SPDN_FALLBACK_TO_PIO;
+ if (arg.nr_errors[ATA_ECAT_TOUT_HSM] +
+ arg.nr_errors[ATA_ECAT_UNK_DEV] > 3)
+ verdict |= ATA_EH_SPDN_NCQ_OFF;
+
+ if (arg.nr_errors[ATA_ECAT_ATA_BUS] +
+ arg.nr_errors[ATA_ECAT_TOUT_HSM] > 3 ||
+ arg.nr_errors[ATA_ECAT_UNK_DEV] > 6)
+ verdict |= ATA_EH_SPDN_SPEED_DOWN;
return verdict;
}
@@ -1549,7 +1641,7 @@ static unsigned int ata_eh_speed_down_verdict(struct ata_device *dev)
/**
* ata_eh_speed_down - record error and speed down if necessary
* @dev: Failed device
- * @is_io: Did the device fail during normal IO?
+ * @eflags: mask of ATA_EFLAG_* flags
* @err_mask: err_mask of the error
*
* Record error and examine error history to determine whether
@@ -1563,18 +1655,20 @@ static unsigned int ata_eh_speed_down_verdict(struct ata_device *dev)
* RETURNS:
* Determined recovery action.
*/
-static unsigned int ata_eh_speed_down(struct ata_device *dev, int is_io,
- unsigned int err_mask)
+static unsigned int ata_eh_speed_down(struct ata_device *dev,
+ unsigned int eflags, unsigned int err_mask)
{
+ struct ata_link *link = dev->link;
+ int xfer_ok = 0;
unsigned int verdict;
unsigned int action = 0;
/* don't bother if Cat-0 error */
- if (ata_eh_categorize_error(is_io, err_mask) == 0)
+ if (ata_eh_categorize_error(eflags, err_mask, &xfer_ok) == 0)
return 0;
/* record error and determine whether speed down is necessary */
- ata_ering_record(&dev->ering, is_io, err_mask);
+ ata_ering_record(&dev->ering, eflags, err_mask);
verdict = ata_eh_speed_down_verdict(dev);
/* turn off NCQ? */
@@ -1590,7 +1684,7 @@ static unsigned int ata_eh_speed_down(struct ata_device *dev, int is_io,
/* speed down? */
if (verdict & ATA_EH_SPDN_SPEED_DOWN) {
/* speed down SATA link speed if possible */
- if (sata_down_spd_limit(dev->link) == 0) {
+ if (sata_down_spd_limit(link) == 0) {
action |= ATA_EH_HARDRESET;
goto done;
}
@@ -1618,10 +1712,10 @@ static unsigned int ata_eh_speed_down(struct ata_device *dev, int is_io,
}
/* Fall back to PIO? Slowing down to PIO is meaningless for
- * SATA. Consider it only for PATA.
+ * SATA ATA devices. Consider it only for PATA and SATAPI.
*/
if ((verdict & ATA_EH_SPDN_FALLBACK_TO_PIO) && (dev->spdn_cnt >= 2) &&
- (dev->link->ap->cbl != ATA_CBL_SATA) &&
+ (link->ap->cbl != ATA_CBL_SATA || dev->class == ATA_DEV_ATAPI) &&
(dev->xfer_shift != ATA_SHIFT_PIO)) {
if (ata_down_xfermask_limit(dev, ATA_DNXFER_FORCE_PIO) == 0) {
dev->spdn_cnt = 0;
@@ -1633,7 +1727,8 @@ static unsigned int ata_eh_speed_down(struct ata_device *dev, int is_io,
return 0;
done:
/* device has been slowed down, blow error history */
- ata_ering_clear(&dev->ering);
+ if (!(verdict & ATA_EH_SPDN_KEEP_ERRORS))
+ ata_ering_clear(&dev->ering);
return action;
}
@@ -1653,8 +1748,8 @@ static void ata_eh_link_autopsy(struct ata_link *link)
struct ata_port *ap = link->ap;
struct ata_eh_context *ehc = &link->eh_context;
struct ata_device *dev;
- unsigned int all_err_mask = 0;
- int tag, is_io = 0;
+ unsigned int all_err_mask = 0, eflags = 0;
+ int tag;
u32 serror;
int rc;
@@ -1713,15 +1808,15 @@ static void ata_eh_link_autopsy(struct ata_link *link)
ehc->i.dev = qc->dev;
all_err_mask |= qc->err_mask;
if (qc->flags & ATA_QCFLAG_IO)
- is_io = 1;
+ eflags |= ATA_EFLAG_IS_IO;
}
/* enforce default EH actions */
if (ap->pflags & ATA_PFLAG_FROZEN ||
all_err_mask & (AC_ERR_HSM | AC_ERR_TIMEOUT))
ehc->i.action |= ATA_EH_SOFTRESET;
- else if ((is_io && all_err_mask) ||
- (!is_io && (all_err_mask & ~AC_ERR_DEV)))
+ else if (((eflags & ATA_EFLAG_IS_IO) && all_err_mask) ||
+ (!(eflags & ATA_EFLAG_IS_IO) && (all_err_mask & ~AC_ERR_DEV)))
ehc->i.action |= ATA_EH_REVALIDATE;
/* If we have offending qcs and the associated failed device,
@@ -1743,8 +1838,11 @@ static void ata_eh_link_autopsy(struct ata_link *link)
ata_dev_enabled(link->device))))
dev = link->device;
- if (dev)
- ehc->i.action |= ata_eh_speed_down(dev, is_io, all_err_mask);
+ if (dev) {
+ if (dev->flags & ATA_DFLAG_DUBIOUS_XFER)
+ eflags |= ATA_EFLAG_DUBIOUS_XFER;
+ ehc->i.action |= ata_eh_speed_down(dev, eflags, all_err_mask);
+ }
DPRINTK("EXIT\n");
}
@@ -1880,8 +1978,8 @@ static void ata_eh_link_report(struct ata_link *link)
[ATA_PROT_PIO] = "pio",
[ATA_PROT_DMA] = "dma",
[ATA_PROT_NCQ] = "ncq",
- [ATA_PROT_ATAPI] = "pio",
- [ATA_PROT_ATAPI_DMA] = "dma",
+ [ATAPI_PROT_PIO] = "pio",
+ [ATAPI_PROT_DMA] = "dma",
};
snprintf(data_buf, sizeof(data_buf), " %s %u %s",
@@ -1889,7 +1987,7 @@ static void ata_eh_link_report(struct ata_link *link)
dma_str[qc->dma_dir]);
}
- if (is_atapi_taskfile(&qc->tf))
+ if (ata_is_atapi(qc->tf.protocol))
snprintf(cdb_buf, sizeof(cdb_buf),
"cdb %02x %02x %02x %02x %02x %02x %02x %02x "
"%02x %02x %02x %02x %02x %02x %02x %02x\n ",
@@ -2329,6 +2427,58 @@ static int ata_eh_revalidate_and_attach(struct ata_link *link,
return rc;
}
+/**
+ * ata_set_mode - Program timings and issue SET FEATURES - XFER
+ * @link: link on which timings will be programmed
+ * @r_failed_dev: out paramter for failed device
+ *
+ * Set ATA device disk transfer mode (PIO3, UDMA6, etc.). If
+ * ata_set_mode() fails, pointer to the failing device is
+ * returned in @r_failed_dev.
+ *
+ * LOCKING:
+ * PCI/etc. bus probe sem.
+ *
+ * RETURNS:
+ * 0 on success, negative errno otherwise
+ */
+int ata_set_mode(struct ata_link *link, struct ata_device **r_failed_dev)
+{
+ struct ata_port *ap = link->ap;
+ struct ata_device *dev;
+ int rc;
+
+ /* if data transfer is verified, clear DUBIOUS_XFER on ering top */
+ ata_link_for_each_dev(dev, link) {
+ if (!(dev->flags & ATA_DFLAG_DUBIOUS_XFER)) {
+ struct ata_ering_entry *ent;
+
+ ent = ata_ering_top(&dev->ering);
+ if (ent)
+ ent->eflags &= ~ATA_EFLAG_DUBIOUS_XFER;
+ }
+ }
+
+ /* has private set_mode? */
+ if (ap->ops->set_mode)
+ rc = ap->ops->set_mode(link, r_failed_dev);
+ else
+ rc = ata_do_set_mode(link, r_failed_dev);
+
+ /* if transfer mode has changed, set DUBIOUS_XFER on device */
+ ata_link_for_each_dev(dev, link) {
+ struct ata_eh_context *ehc = &link->eh_context;
+ u8 saved_xfer_mode = ehc->saved_xfer_mode[dev->devno];
+ u8 saved_ncq = !!(ehc->saved_ncq_enabled & (1 << dev->devno));
+
+ if (dev->xfer_mode != saved_xfer_mode ||
+ ata_ncq_enabled(dev) != saved_ncq)
+ dev->flags |= ATA_DFLAG_DUBIOUS_XFER;
+ }
+
+ return rc;
+}
+
static int ata_link_nr_enabled(struct ata_link *link)
{
struct ata_device *dev;
@@ -2375,6 +2525,24 @@ static int ata_eh_skip_recovery(struct ata_link *link)
return 1;
}
+static int ata_eh_schedule_probe(struct ata_device *dev)
+{
+ struct ata_eh_context *ehc = &dev->link->eh_context;
+
+ if (!(ehc->i.probe_mask & (1 << dev->devno)) ||
+ (ehc->did_probe_mask & (1 << dev->devno)))
+ return 0;
+
+ ata_eh_detach_dev(dev);
+ ata_dev_init(dev);
+ ehc->did_probe_mask |= (1 << dev->devno);
+ ehc->i.action |= ATA_EH_SOFTRESET;
+ ehc->saved_xfer_mode[dev->devno] = 0;
+ ehc->saved_ncq_enabled &= ~(1 << dev->devno);
+
+ return 1;
+}
+
static int ata_eh_handle_dev_fail(struct ata_device *dev, int err)
{
struct ata_eh_context *ehc = &dev->link->eh_context;
@@ -2406,16 +2574,9 @@ static int ata_eh_handle_dev_fail(struct ata_device *dev, int err)
if (ata_link_offline(dev->link))
ata_eh_detach_dev(dev);
- /* probe if requested */
- if ((ehc->i.probe_mask & (1 << dev->devno)) &&
- !(ehc->did_probe_mask & (1 << dev->devno))) {
- ata_eh_detach_dev(dev);
- ata_dev_init(dev);
-
+ /* schedule probe if necessary */
+ if (ata_eh_schedule_probe(dev))
ehc->tries[dev->devno] = ATA_EH_DEV_TRIES;
- ehc->did_probe_mask |= (1 << dev->devno);
- ehc->i.action |= ATA_EH_SOFTRESET;
- }
return 1;
} else {
@@ -2492,14 +2653,9 @@ int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
if (dev->flags & ATA_DFLAG_DETACH)
ata_eh_detach_dev(dev);
- if (!ata_dev_enabled(dev) &&
- ((ehc->i.probe_mask & (1 << dev->devno)) &&
- !(ehc->did_probe_mask & (1 << dev->devno)))) {
- ata_eh_detach_dev(dev);
- ata_dev_init(dev);
- ehc->did_probe_mask |= (1 << dev->devno);
- ehc->i.action |= ATA_EH_SOFTRESET;
- }
+ /* schedule probe if necessary */
+ if (!ata_dev_enabled(dev))
+ ata_eh_schedule_probe(dev);
}
}
@@ -2747,6 +2903,7 @@ static void ata_eh_handle_port_suspend(struct ata_port *ap)
if (ap->ops->port_suspend)
rc = ap->ops->port_suspend(ap, ap->pm_mesg);
+ ata_acpi_set_state(ap, PMSG_SUSPEND);
out:
/* report result */
spin_lock_irqsave(ap->lock, flags);
@@ -2792,6 +2949,8 @@ static void ata_eh_handle_port_resume(struct ata_port *ap)
WARN_ON(!(ap->pflags & ATA_PFLAG_SUSPENDED));
+ ata_acpi_set_state(ap, PMSG_ON);
+
if (ap->ops->port_resume)
rc = ap->ops->port_resume(ap);
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 14daf48..3fd0820 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -517,7 +517,7 @@ static struct ata_queued_cmd *ata_scsi_qc_new(struct ata_device *dev,
qc->scsicmd = cmd;
qc->scsidone = done;
- qc->__sg = scsi_sglist(cmd);
+ qc->sg = scsi_sglist(cmd);
qc->n_elem = scsi_sg_count(cmd);
} else {
cmd->result = (DID_OK << 16) | (QUEUE_FULL << 1);
@@ -2210,7 +2210,7 @@ unsigned int ata_scsiop_read_cap(struct ata_scsi_args *args, u8 *rbuf,
/* sector size */
ATA_SCSI_RBUF_SET(6, ATA_SECT_SIZE >> 8);
- ATA_SCSI_RBUF_SET(7, ATA_SECT_SIZE);
+ ATA_SCSI_RBUF_SET(7, ATA_SECT_SIZE & 0xff);
} else {
/* sector count, 64-bit */
ATA_SCSI_RBUF_SET(0, last_lba >> (8 * 7));
@@ -2224,7 +2224,7 @@ unsigned int ata_scsiop_read_cap(struct ata_scsi_args *args, u8 *rbuf,
/* sector size */
ATA_SCSI_RBUF_SET(10, ATA_SECT_SIZE >> 8);
- ATA_SCSI_RBUF_SET(11, ATA_SECT_SIZE);
+ ATA_SCSI_RBUF_SET(11, ATA_SECT_SIZE & 0xff);
}
return 0;
@@ -2331,7 +2331,7 @@ static void atapi_request_sense(struct ata_queued_cmd *qc)
DPRINTK("ATAPI request sense\n");
/* FIXME: is this needed? */
- memset(cmd->sense_buffer, 0, sizeof(cmd->sense_buffer));
+ memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE);
ap->ops->tf_read(ap, &qc->tf);
@@ -2341,7 +2341,9 @@ static void atapi_request_sense(struct ata_queued_cmd *qc)
ata_qc_reinit(qc);
- ata_sg_init_one(qc, cmd->sense_buffer, sizeof(cmd->sense_buffer));
+ /* setup sg table and init transfer direction */
+ sg_init_one(&qc->sgent, cmd->sense_buffer, SCSI_SENSE_BUFFERSIZE);
+ ata_sg_init(qc, &qc->sgent, 1);
qc->dma_dir = DMA_FROM_DEVICE;
memset(&qc->cdb, 0, qc->dev->cdb_len);
@@ -2352,10 +2354,10 @@ static void atapi_request_sense(struct ata_queued_cmd *qc)
qc->tf.command = ATA_CMD_PACKET;
if (ata_pio_use_silly(ap)) {
- qc->tf.protocol = ATA_PROT_ATAPI_DMA;
+ qc->tf.protocol = ATAPI_PROT_DMA;
qc->tf.feature |= ATAPI_PKT_DMA;
} else {
- qc->tf.protocol = ATA_PROT_ATAPI;
+ qc->tf.protocol = ATAPI_PROT_PIO;
qc->tf.lbam = SCSI_SENSE_BUFFERSIZE;
qc->tf.lbah = 0;
}
@@ -2526,12 +2528,12 @@ static unsigned int atapi_xlat(struct ata_queued_cmd *qc)
if (using_pio || nodata) {
/* no data, or PIO data xfer */
if (nodata)
- qc->tf.protocol = ATA_PROT_ATAPI_NODATA;
+ qc->tf.protocol = ATAPI_PROT_NODATA;
else
- qc->tf.protocol = ATA_PROT_ATAPI;
+ qc->tf.protocol = ATAPI_PROT_PIO;
} else {
/* DMA data xfer */
- qc->tf.protocol = ATA_PROT_ATAPI_DMA;
+ qc->tf.protocol = ATAPI_PROT_DMA;
qc->tf.feature |= ATAPI_PKT_DMA;
if (atapi_dmadir && (scmd->sc_data_direction != DMA_TO_DEVICE))
@@ -2690,6 +2692,24 @@ static unsigned int ata_scsi_pass_thru(struct ata_queued_cmd *qc)
if ((tf->protocol = ata_scsi_map_proto(cdb[1])) == ATA_PROT_UNKNOWN)
goto invalid_fld;
+ /*
+ * Filter TPM commands by default. These provide an
+ * essentially uncontrolled encrypted "back door" between
+ * applications and the disk. Set libata.allow_tpm=1 if you
+ * have a real reason for wanting to use them. This ensures
+ * that installed software cannot easily mess stuff up without
+ * user intent. DVR type users will probably ship with this enabled
+ * for movie content management.
+ *
+ * Note that for ATA8 we can issue a DCS change and DCS freeze lock
+ * for this and should do in future but that it is not sufficient as
+ * DCS is an optional feature set. Thus we also do the software filter
+ * so that we comply with the TC consortium stated goal that the user
+ * can turn off TC features of their system.
+ */
+ if (tf->command >= 0x5C && tf->command <= 0x5F && !libata_allow_tpm)
+ goto invalid_fld;
+
/* We may not issue DMA commands if no DMA mode is set */
if (tf->protocol == ATA_PROT_DMA && dev->dma_mode == 0)
goto invalid_fld;
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index b7ac80b..60cd4b1 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -147,7 +147,9 @@ void ata_exec_command(struct ata_port *ap, const struct ata_taskfile *tf)
* @tf: ATA taskfile register set for storing input
*
* Reads ATA taskfile registers for currently-selected device
- * into @tf.
+ * into @tf. Assumes the device has a fully SFF compliant task file
+ * layout and behaviour. If you device does not (eg has a different
+ * status method) then you will need to provide a replacement tf_read
*
* LOCKING:
* Inherited from caller.
@@ -156,7 +158,7 @@ void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
- tf->command = ata_chk_status(ap);
+ tf->command = ata_check_status(ap);
tf->feature = ioread8(ioaddr->error_addr);
tf->nsect = ioread8(ioaddr->nsect_addr);
tf->lbal = ioread8(ioaddr->lbal_addr);
@@ -415,7 +417,7 @@ void ata_bmdma_drive_eh(struct ata_port *ap, ata_prereset_fn_t prereset,
ap->hsm_task_state = HSM_ST_IDLE;
if (qc && (qc->tf.protocol == ATA_PROT_DMA ||
- qc->tf.protocol == ATA_PROT_ATAPI_DMA)) {
+ qc->tf.protocol == ATAPI_PROT_DMA)) {
u8 host_stat;
host_stat = ap->ops->bmdma_status(ap);
@@ -549,7 +551,7 @@ int ata_pci_init_bmdma(struct ata_host *host)
return rc;
/* request and iomap DMA region */
- rc = pcim_iomap_regions(pdev, 1 << 4, DRV_NAME);
+ rc = pcim_iomap_regions(pdev, 1 << 4, dev_driver_string(gdev));
if (rc) {
dev_printk(KERN_ERR, gdev, "failed to request/iomap BAR4\n");
return -ENOMEM;
@@ -619,7 +621,8 @@ int ata_pci_init_sff_host(struct ata_host *host)
continue;
}
- rc = pcim_iomap_regions(pdev, 0x3 << base, DRV_NAME);
+ rc = pcim_iomap_regions(pdev, 0x3 << base,
+ dev_driver_string(gdev));
if (rc) {
dev_printk(KERN_WARNING, gdev,
"failed to request/iomap BARs for port %d "
@@ -711,6 +714,99 @@ int ata_pci_prepare_sff_host(struct pci_dev *pdev,
}
/**
+ * ata_pci_activate_sff_host - start SFF host, request IRQ and register it
+ * @host: target SFF ATA host
+ * @irq_handler: irq_handler used when requesting IRQ(s)
+ * @sht: scsi_host_template to use when registering the host
+ *
+ * This is the counterpart of ata_host_activate() for SFF ATA
+ * hosts. This separate helper is necessary because SFF hosts
+ * use two separate interrupts in legacy mode.
+ *
+ * LOCKING:
+ * Inherited from calling layer (may sleep).
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
+ */
+int ata_pci_activate_sff_host(struct ata_host *host,
+ irq_handler_t irq_handler,
+ struct scsi_host_template *sht)
+{
+ struct device *dev = host->dev;
+ struct pci_dev *pdev = to_pci_dev(dev);
+ const char *drv_name = dev_driver_string(host->dev);
+ int legacy_mode = 0, rc;
+
+ rc = ata_host_start(host);
+ if (rc)
+ return rc;
+
+ if ((pdev->class >> 8) == PCI_CLASS_STORAGE_IDE) {
+ u8 tmp8, mask;
+
+ /* TODO: What if one channel is in native mode ... */
+ pci_read_config_byte(pdev, PCI_CLASS_PROG, &tmp8);
+ mask = (1 << 2) | (1 << 0);
+ if ((tmp8 & mask) != mask)
+ legacy_mode = 1;
+#if defined(CONFIG_NO_ATA_LEGACY)
+ /* Some platforms with PCI limits cannot address compat
+ port space. In that case we punt if their firmware has
+ left a device in compatibility mode */
+ if (legacy_mode) {
+ printk(KERN_ERR "ata: Compatibility mode ATA is not supported on this platform, skipping.\n");
+ return -EOPNOTSUPP;
+ }
+#endif
+ }
+
+ if (!devres_open_group(dev, NULL, GFP_KERNEL))
+ return -ENOMEM;
+
+ if (!legacy_mode && pdev->irq) {
+ rc = devm_request_irq(dev, pdev->irq, irq_handler,
+ IRQF_SHARED, drv_name, host);
+ if (rc)
+ goto out;
+
+ ata_port_desc(host->ports[0], "irq %d", pdev->irq);
+ ata_port_desc(host->ports[1], "irq %d", pdev->irq);
+ } else if (legacy_mode) {
+ if (!ata_port_is_dummy(host->ports[0])) {
+ rc = devm_request_irq(dev, ATA_PRIMARY_IRQ(pdev),
+ irq_handler, IRQF_SHARED,
+ drv_name, host);
+ if (rc)
+ goto out;
+
+ ata_port_desc(host->ports[0], "irq %d",
+ ATA_PRIMARY_IRQ(pdev));
+ }
+
+ if (!ata_port_is_dummy(host->ports[1])) {
+ rc = devm_request_irq(dev, ATA_SECONDARY_IRQ(pdev),
+ irq_handler, IRQF_SHARED,
+ drv_name, host);
+ if (rc)
+ goto out;
+
+ ata_port_desc(host->ports[1], "irq %d",
+ ATA_SECONDARY_IRQ(pdev));
+ }
+ }
+
+ rc = ata_host_register(host, sht);
+ out:
+ if (rc == 0)
+ devres_remove_group(dev, NULL);
+ else
+ devres_release_group(dev, NULL);
+
+ return rc;
+}
+
+/**
* ata_pci_init_one - Initialize/register PCI IDE host controller
* @pdev: Controller to be initialized
* @ppi: array of port_info, must be enough for two ports
@@ -739,8 +835,6 @@ int ata_pci_init_one(struct pci_dev *pdev,
struct device *dev = &pdev->dev;
const struct ata_port_info *pi = NULL;
struct ata_host *host = NULL;
- u8 mask;
- int legacy_mode = 0;
int i, rc;
DPRINTK("ENTER\n");
@@ -762,95 +856,24 @@ int ata_pci_init_one(struct pci_dev *pdev,
if (!devres_open_group(dev, NULL, GFP_KERNEL))
return -ENOMEM;
- /* FIXME: Really for ATA it isn't safe because the device may be
- multi-purpose and we want to leave it alone if it was already
- enabled. Secondly for shared use as Arjan says we want refcounting
-
- Checking dev->is_enabled is insufficient as this is not set at
- boot for the primary video which is BIOS enabled
- */
-
rc = pcim_enable_device(pdev);
if (rc)
- goto err_out;
+ goto out;
- if ((pdev->class >> 8) == PCI_CLASS_STORAGE_IDE) {
- u8 tmp8;
-
- /* TODO: What if one channel is in native mode ... */
- pci_read_config_byte(pdev, PCI_CLASS_PROG, &tmp8);
- mask = (1 << 2) | (1 << 0);
- if ((tmp8 & mask) != mask)
- legacy_mode = 1;
-#if defined(CONFIG_NO_ATA_LEGACY)
- /* Some platforms with PCI limits cannot address compat
- port space. In that case we punt if their firmware has
- left a device in compatibility mode */
- if (legacy_mode) {
- printk(KERN_ERR "ata: Compatibility mode ATA is not supported on this platform, skipping.\n");
- rc = -EOPNOTSUPP;
- goto err_out;
- }
-#endif
- }
-
- /* prepare host */
+ /* prepare and activate SFF host */
rc = ata_pci_prepare_sff_host(pdev, ppi, &host);
if (rc)
- goto err_out;
+ goto out;
pci_set_master(pdev);
+ rc = ata_pci_activate_sff_host(host, pi->port_ops->irq_handler,
+ pi->sht);
+ out:
+ if (rc == 0)
+ devres_remove_group(&pdev->dev, NULL);
+ else
+ devres_release_group(&pdev->dev, NULL);
- /* start host and request IRQ */
- rc = ata_host_start(host);
- if (rc)
- goto err_out;
-
- if (!legacy_mode && pdev->irq) {
- /* We may have no IRQ assigned in which case we can poll. This
- shouldn't happen on a sane system but robustness is cheap
- in this case */
- rc = devm_request_irq(dev, pdev->irq, pi->port_ops->irq_handler,
- IRQF_SHARED, DRV_NAME, host);
- if (rc)
- goto err_out;
-
- ata_port_desc(host->ports[0], "irq %d", pdev->irq);
- ata_port_desc(host->ports[1], "irq %d", pdev->irq);
- } else if (legacy_mode) {
- if (!ata_port_is_dummy(host->ports[0])) {
- rc = devm_request_irq(dev, ATA_PRIMARY_IRQ(pdev),
- pi->port_ops->irq_handler,
- IRQF_SHARED, DRV_NAME, host);
- if (rc)
- goto err_out;
-
- ata_port_desc(host->ports[0], "irq %d",
- ATA_PRIMARY_IRQ(pdev));
- }
-
- if (!ata_port_is_dummy(host->ports[1])) {
- rc = devm_request_irq(dev, ATA_SECONDARY_IRQ(pdev),
- pi->port_ops->irq_handler,
- IRQF_SHARED, DRV_NAME, host);
- if (rc)
- goto err_out;
-
- ata_port_desc(host->ports[1], "irq %d",
- ATA_SECONDARY_IRQ(pdev));
- }
- }
-
- /* register */
- rc = ata_host_register(host, pi->sht);
- if (rc)
- goto err_out;
-
- devres_remove_group(dev, NULL);
- return 0;
-
-err_out:
- devres_release_group(dev, NULL);
return rc;
}
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index bbe59c2..409ffb9 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -60,6 +60,7 @@ extern int atapi_dmadir;
extern int atapi_passthru16;
extern int libata_fua;
extern int libata_noacpi;
+extern int libata_allow_tpm;
extern struct ata_queued_cmd *ata_qc_new_init(struct ata_device *dev);
extern int ata_build_rw_tf(struct ata_taskfile *tf, struct ata_device *dev,
u64 block, u32 n_block, unsigned int tf_flags,
@@ -85,7 +86,6 @@ extern int ata_dev_configure(struct ata_device *dev);
extern int sata_down_spd_limit(struct ata_link *link);
extern int sata_set_spd_needed(struct ata_link *link);
extern int ata_down_xfermask_limit(struct ata_device *dev, unsigned int sel);
-extern int ata_set_mode(struct ata_link *link, struct ata_device **r_failed_dev);
extern void ata_sg_clean(struct ata_queued_cmd *qc);
extern void ata_qc_free(struct ata_queued_cmd *qc);
extern void ata_qc_issue(struct ata_queued_cmd *qc);
@@ -113,6 +113,7 @@ extern int ata_acpi_on_suspend(struct ata_port *ap);
extern void ata_acpi_on_resume(struct ata_port *ap);
extern int ata_acpi_on_devcfg(struct ata_device *dev);
extern void ata_acpi_on_disable(struct ata_device *dev);
+extern void ata_acpi_set_state(struct ata_port *ap, pm_message_t state);
#else
static inline void ata_acpi_associate_sata_port(struct ata_port *ap) { }
static inline void ata_acpi_associate(struct ata_host *host) { }
@@ -121,6 +122,8 @@ static inline int ata_acpi_on_suspend(struct ata_port *ap) { return 0; }
static inline void ata_acpi_on_resume(struct ata_port *ap) { }
static inline int ata_acpi_on_devcfg(struct ata_device *dev) { return 0; }
static inline void ata_acpi_on_disable(struct ata_device *dev) { }
+static inline void ata_acpi_set_state(struct ata_port *ap,
+ pm_message_t state) { }
#endif
/* libata-scsi.c */
@@ -183,6 +186,7 @@ extern void ata_eh_report(struct ata_port *ap);
extern int ata_eh_reset(struct ata_link *link, int classify,
ata_prereset_fn_t prereset, ata_reset_fn_t softreset,
ata_reset_fn_t hardreset, ata_postreset_fn_t postreset);
+extern int ata_set_mode(struct ata_link *link, struct ata_device **r_failed_dev);
extern int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
ata_reset_fn_t softreset, ata_reset_fn_t hardreset,
ata_postreset_fn_t postreset,
diff --git a/drivers/ata/pata_acpi.c b/drivers/ata/pata_acpi.c
index e4542ab..244098a 100644
--- a/drivers/ata/pata_acpi.c
+++ b/drivers/ata/pata_acpi.c
@@ -81,17 +81,6 @@ static void pacpi_error_handler(struct ata_port *ap)
NULL, ata_std_postreset);
}
-/* Welcome to ACPI, bring a bucket */
-static const unsigned int pio_cycle[7] = {
- 600, 383, 240, 180, 120, 100, 80
-};
-static const unsigned int mwdma_cycle[5] = {
- 480, 150, 120, 100, 80
-};
-static const unsigned int udma_cycle[7] = {
- 120, 80, 60, 45, 30, 20, 15
-};
-
/**
* pacpi_discover_modes - filter non ACPI modes
* @adev: ATA device
@@ -103,56 +92,20 @@ static const unsigned int udma_cycle[7] = {
static unsigned long pacpi_discover_modes(struct ata_port *ap, struct ata_device *adev)
{
- int unit = adev->devno;
struct pata_acpi *acpi = ap->private_data;
- int i;
- u32 t;
- unsigned long mask = (0x7f << ATA_SHIFT_UDMA) | (0x7 << ATA_SHIFT_MWDMA) | (0x1F << ATA_SHIFT_PIO);
-
struct ata_acpi_gtm probe;
+ unsigned int xfer_mask;
probe = acpi->gtm;
- /* We always use the 0 slot for crap hardware */
- if (!(probe.flags & 0x10))
- unit = 0;
-
ata_acpi_gtm(ap, &probe);
- /* Start by scanning for PIO modes */
- for (i = 0; i < 7; i++) {
- t = probe.drive[unit].pio;
- if (t <= pio_cycle[i]) {
- mask |= (2 << (ATA_SHIFT_PIO + i)) - 1;
- break;
- }
- }
+ xfer_mask = ata_acpi_gtm_xfermask(adev, &probe);
- /* See if we have MWDMA or UDMA data. We don't bother with MWDMA
- if UDMA is availabe as this means the BIOS set UDMA and our
- error changedown if it works is UDMA to PIO anyway */
- if (probe.flags & (1 << (2 * unit))) {
- /* MWDMA */
- for (i = 0; i < 5; i++) {
- t = probe.drive[unit].dma;
- if (t <= mwdma_cycle[i]) {
- mask |= (2 << (ATA_SHIFT_MWDMA + i)) - 1;
- break;
- }
- }
- } else {
- /* UDMA */
- for (i = 0; i < 7; i++) {
- t = probe.drive[unit].dma;
- if (t <= udma_cycle[i]) {
- mask |= (2 << (ATA_SHIFT_UDMA + i)) - 1;
- break;
- }
- }
- }
- if (mask & (0xF8 << ATA_SHIFT_UDMA))
+ if (xfer_mask & (0xF8 << ATA_SHIFT_UDMA))
ap->cbl = ATA_CBL_PATA80;
- return mask;
+
+ return xfer_mask;
}
/**
@@ -180,12 +133,14 @@ static void pacpi_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
int unit = adev->devno;
struct pata_acpi *acpi = ap->private_data;
+ const struct ata_timing *t;
if (!(acpi->gtm.flags & 0x10))
unit = 0;
/* Now stuff the nS values into the structure */
- acpi->gtm.drive[unit].pio = pio_cycle[adev->pio_mode - XFER_PIO_0];
+ t = ata_timing_find_mode(adev->pio_mode);
+ acpi->gtm.drive[unit].pio = t->cycle;
ata_acpi_stm(ap, &acpi->gtm);
/* See what mode we actually got */
ata_acpi_gtm(ap, &acpi->gtm);
@@ -201,16 +156,18 @@ static void pacpi_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
int unit = adev->devno;
struct pata_acpi *acpi = ap->private_data;
+ const struct ata_timing *t;
if (!(acpi->gtm.flags & 0x10))
unit = 0;
/* Now stuff the nS values into the structure */
+ t = ata_timing_find_mode(adev->dma_mode);
if (adev->dma_mode >= XFER_UDMA_0) {
- acpi->gtm.drive[unit].dma = udma_cycle[adev->dma_mode - XFER_UDMA_0];
+ acpi->gtm.drive[unit].dma = t->udma;
acpi->gtm.flags |= (1 << (2 * unit));
} else {
- acpi->gtm.drive[unit].dma = mwdma_cycle[adev->dma_mode - XFER_MW_DMA_0];
+ acpi->gtm.drive[unit].dma = t->cycle;
acpi->gtm.flags &= ~(1 << (2 * unit));
}
ata_acpi_stm(ap, &acpi->gtm);
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index 8caf9af..7e68edf 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -64,7 +64,7 @@ static int ali_cable_override(struct pci_dev *pdev)
if (pdev->subsystem_vendor == 0x10CF && pdev->subsystem_device == 0x10AF)
return 1;
/* Mitac 8317 (Winbook-A) and relatives */
- if (pdev->subsystem_vendor == 0x1071 && pdev->subsystem_device == 0x8317)
+ if (pdev->subsystem_vendor == 0x1071 && pdev->subsystem_device == 0x8317)
return 1;
/* Systems by DMI */
if (dmi_check_system(cable_dmi_table))
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index 3cc27b5..761a666 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -220,6 +220,62 @@ static void amd133_set_dmamode(struct ata_port *ap, struct ata_device *adev)
timing_setup(ap, adev, 0x40, adev->dma_mode, 4);
}
+/* Both host-side and drive-side detection results are worthless on NV
+ * PATAs. Ignore them and just follow what BIOS configured. Both the
+ * current configuration in PCI config reg and ACPI GTM result are
+ * cached during driver attach and are consulted to select transfer
+ * mode.
+ */
+static unsigned long nv_mode_filter(struct ata_device *dev,
+ unsigned long xfer_mask)
+{
+ static const unsigned int udma_mask_map[] =
+ { ATA_UDMA2, ATA_UDMA1, ATA_UDMA0, 0,
+ ATA_UDMA3, ATA_UDMA4, ATA_UDMA5, ATA_UDMA6 };
+ struct ata_port *ap = dev->link->ap;
+ char acpi_str[32] = "";
+ u32 saved_udma, udma;
+ const struct ata_acpi_gtm *gtm;
+ unsigned long bios_limit = 0, acpi_limit = 0, limit;
+
+ /* find out what BIOS configured */
+ udma = saved_udma = (unsigned long)ap->host->private_data;
+
+ if (ap->port_no == 0)
+ udma >>= 16;
+ if (dev->devno == 0)
+ udma >>= 8;
+
+ if ((udma & 0xc0) == 0xc0)
+ bios_limit = ata_pack_xfermask(0, 0, udma_mask_map[udma & 0x7]);
+
+ /* consult ACPI GTM too */
+ gtm = ata_acpi_init_gtm(ap);
+ if (gtm) {
+ acpi_limit = ata_acpi_gtm_xfermask(dev, gtm);
+
+ snprintf(acpi_str, sizeof(acpi_str), " (%u:%u:0x%x)",
+ gtm->drive[0].dma, gtm->drive[1].dma, gtm->flags);
+ }
+
+ /* be optimistic, EH can take care of things if something goes wrong */
+ limit = bios_limit | acpi_limit;
+
+ /* If PIO or DMA isn't configured at all, don't limit. Let EH
+ * handle it.
+ */
+ if (!(limit & ATA_MASK_PIO))
+ limit |= ATA_MASK_PIO;
+ if (!(limit & (ATA_MASK_MWDMA | ATA_MASK_UDMA)))
+ limit |= ATA_MASK_MWDMA | ATA_MASK_UDMA;
+
+ ata_port_printk(ap, KERN_DEBUG, "nv_mode_filter: 0x%lx&0x%lx->0x%lx, "
+ "BIOS=0x%lx (0x%x) ACPI=0x%lx%s\n",
+ xfer_mask, limit, xfer_mask & limit, bios_limit,
+ saved_udma, acpi_limit, acpi_str);
+
+ return xfer_mask & limit;
+}
/**
* nv_probe_init - cable detection
@@ -252,31 +308,6 @@ static void nv_error_handler(struct ata_port *ap)
ata_std_postreset);
}
-static int nv_cable_detect(struct ata_port *ap)
-{
- static const u8 bitmask[2] = {0x03, 0x0C};
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u8 ata66;
- u16 udma;
- int cbl;
-
- pci_read_config_byte(pdev, 0x52, &ata66);
- if (ata66 & bitmask[ap->port_no])
- cbl = ATA_CBL_PATA80;
- else
- cbl = ATA_CBL_PATA40;
-
- /* We now have to double check because the Nvidia boxes BIOS
- doesn't always set the cable bits but does set mode bits */
- pci_read_config_word(pdev, 0x62 - 2 * ap->port_no, &udma);
- if ((udma & 0xC4) == 0xC4 || (udma & 0xC400) == 0xC400)
- cbl = ATA_CBL_PATA80;
- /* And a triple check across suspend/resume with ACPI around */
- if (ata_acpi_cbl_80wire(ap))
- cbl = ATA_CBL_PATA80;
- return cbl;
-}
-
/**
* nv100_set_piomode - set initial PIO mode data
* @ap: ATA interface
@@ -314,6 +345,14 @@ static void nv133_set_dmamode(struct ata_port *ap, struct ata_device *adev)
timing_setup(ap, adev, 0x50, adev->dma_mode, 4);
}
+static void nv_host_stop(struct ata_host *host)
+{
+ u32 udma = (unsigned long)host->private_data;
+
+ /* restore PCI config register 0x60 */
+ pci_write_config_dword(to_pci_dev(host->dev), 0x60, udma);
+}
+
static struct scsi_host_template amd_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
@@ -478,7 +517,8 @@ static struct ata_port_operations nv100_port_ops = {
.thaw = ata_bmdma_thaw,
.error_handler = nv_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
- .cable_detect = nv_cable_detect,
+ .cable_detect = ata_cable_ignore,
+ .mode_filter = nv_mode_filter,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
@@ -495,6 +535,7 @@ static struct ata_port_operations nv100_port_ops = {
.irq_on = ata_irq_on,
.port_start = ata_sff_port_start,
+ .host_stop = nv_host_stop,
};
static struct ata_port_operations nv133_port_ops = {
@@ -511,7 +552,8 @@ static struct ata_port_operations nv133_port_ops = {
.thaw = ata_bmdma_thaw,
.error_handler = nv_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
- .cable_detect = nv_cable_detect,
+ .cable_detect = ata_cable_ignore,
+ .mode_filter = nv_mode_filter,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
@@ -528,6 +570,7 @@ static struct ata_port_operations nv133_port_ops = {
.irq_on = ata_irq_on,
.port_start = ata_sff_port_start,
+ .host_stop = nv_host_stop,
};
static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
@@ -614,7 +657,8 @@ static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &amd100_port_ops
}
};
- const struct ata_port_info *ppi[] = { NULL, NULL };
+ struct ata_port_info pi;
+ const struct ata_port_info *ppi[] = { &pi, NULL };
static int printed_version;
int type = id->driver_data;
u8 fifo;
@@ -628,6 +672,19 @@ static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
if (type == 1 && pdev->revision > 0x7)
type = 2;
+ /* Serenade ? */
+ if (type == 5 && pdev->subsystem_vendor == PCI_VENDOR_ID_AMD &&
+ pdev->subsystem_device == PCI_DEVICE_ID_AMD_SERENADE)
+ type = 6; /* UDMA 100 only */
+
+ /*
+ * Okay, type is determined now. Apply type-specific workarounds.
+ */
+ pi = info[type];
+
+ if (type < 3)
+ ata_pci_clear_simplex(pdev);
+
/* Check for AMD7411 */
if (type == 3)
/* FIFO is broken */
@@ -635,16 +692,17 @@ static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
else
pci_write_config_byte(pdev, 0x41, fifo | 0xF0);
- /* Serenade ? */
- if (type == 5 && pdev->subsystem_vendor == PCI_VENDOR_ID_AMD &&
- pdev->subsystem_device == PCI_DEVICE_ID_AMD_SERENADE)
- type = 6; /* UDMA 100 only */
+ /* Cable detection on Nvidia chips doesn't work too well,
+ * cache BIOS programmed UDMA mode.
+ */
+ if (type == 7 || type == 8) {
+ u32 udma;
- if (type < 3)
- ata_pci_clear_simplex(pdev);
+ pci_read_config_dword(pdev, 0x60, &udma);
+ pi.private_data = (void *)(unsigned long)udma;
+ }
/* And fire it up */
- ppi[0] = &info[type];
return ata_pci_init_one(pdev, ppi);
}
diff --git a/drivers/ata/pata_bf54x.c b/drivers/ata/pata_bf54x.c
index 7842cc4..a32e3c4 100644
--- a/drivers/ata/pata_bf54x.c
+++ b/drivers/ata/pata_bf54x.c
@@ -832,6 +832,7 @@ static void bfin_bmdma_setup(struct ata_queued_cmd *qc)
{
unsigned short config = WDSIZE_16;
struct scatterlist *sg;
+ unsigned int si;
pr_debug("in atapi dma setup\n");
/* Program the ATA_CTRL register with dir */
@@ -839,7 +840,7 @@ static void bfin_bmdma_setup(struct ata_queued_cmd *qc)
/* fill the ATAPI DMA controller */
set_dma_config(CH_ATAPI_TX, config);
set_dma_x_modify(CH_ATAPI_TX, 2);
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
set_dma_start_addr(CH_ATAPI_TX, sg_dma_address(sg));
set_dma_x_count(CH_ATAPI_TX, sg_dma_len(sg) >> 1);
}
@@ -848,7 +849,7 @@ static void bfin_bmdma_setup(struct ata_queued_cmd *qc)
/* fill the ATAPI DMA controller */
set_dma_config(CH_ATAPI_RX, config);
set_dma_x_modify(CH_ATAPI_RX, 2);
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
set_dma_start_addr(CH_ATAPI_RX, sg_dma_address(sg));
set_dma_x_count(CH_ATAPI_RX, sg_dma_len(sg) >> 1);
}
@@ -867,6 +868,7 @@ static void bfin_bmdma_start(struct ata_queued_cmd *qc)
struct ata_port *ap = qc->ap;
void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
struct scatterlist *sg;
+ unsigned int si;
pr_debug("in atapi dma start\n");
if (!(ap->udma_mask || ap->mwdma_mask))
@@ -881,7 +883,7 @@ static void bfin_bmdma_start(struct ata_queued_cmd *qc)
* data cache is enabled. Otherwise, this loop
* is an empty loop and optimized out.
*/
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
flush_dcache_range(sg_dma_address(sg),
sg_dma_address(sg) + sg_dma_len(sg));
}
@@ -910,7 +912,7 @@ static void bfin_bmdma_start(struct ata_queued_cmd *qc)
ATAPI_SET_CONTROL(base, ATAPI_GET_CONTROL(base) | TFRCNT_RST);
/* Set transfer length to buffer len */
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
ATAPI_SET_XFER_LEN(base, (sg_dma_len(sg) >> 1));
}
@@ -932,6 +934,7 @@ static void bfin_bmdma_stop(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct scatterlist *sg;
+ unsigned int si;
pr_debug("in atapi dma stop\n");
if (!(ap->udma_mask || ap->mwdma_mask))
@@ -950,7 +953,7 @@ static void bfin_bmdma_stop(struct ata_queued_cmd *qc)
* data cache is enabled. Otherwise, this loop
* is an empty loop and optimized out.
*/
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
invalidate_dcache_range(
sg_dma_address(sg),
sg_dma_address(sg)
@@ -1167,34 +1170,36 @@ static unsigned char bfin_bmdma_status(struct ata_port *ap)
* Note: Original code is ata_data_xfer().
*/
-static void bfin_data_xfer(struct ata_device *adev, unsigned char *buf,
- unsigned int buflen, int write_data)
+static unsigned int bfin_data_xfer(struct ata_device *dev, unsigned char *buf,
+ unsigned int buflen, int rw)
{
- struct ata_port *ap = adev->link->ap;
- unsigned int words = buflen >> 1;
- unsigned short *buf16 = (u16 *) buf;
+ struct ata_port *ap = dev->link->ap;
void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
+ unsigned int words = buflen >> 1;
+ unsigned short *buf16 = (u16 *)buf;
/* Transfer multiple of 2 bytes */
- if (write_data) {
- write_atapi_data(base, words, buf16);
- } else {
+ if (rw == READ)
read_atapi_data(base, words, buf16);
- }
+ else
+ write_atapi_data(base, words, buf16);
/* Transfer trailing 1 byte, if any. */
if (unlikely(buflen & 0x01)) {
unsigned short align_buf[1] = { 0 };
unsigned char *trailing_buf = buf + buflen - 1;
- if (write_data) {
- memcpy(align_buf, trailing_buf, 1);
- write_atapi_data(base, 1, align_buf);
- } else {
+ if (rw == READ) {
read_atapi_data(base, 1, align_buf);
memcpy(trailing_buf, align_buf, 1);
+ } else {
+ memcpy(align_buf, trailing_buf, 1);
+ write_atapi_data(base, 1, align_buf);
}
+ words++;
}
+
+ return words << 1;
}
/**
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c
index 33f7f08..d4590f5 100644
--- a/drivers/ata/pata_cs5520.c
+++ b/drivers/ata/pata_cs5520.c
@@ -198,7 +198,7 @@ static int __devinit cs5520_init_one(struct pci_dev *pdev, const struct pci_devi
};
const struct ata_port_info *ppi[2];
u8 pcicfg;
- void *iomap[5];
+ void __iomem *iomap[5];
struct ata_host *host;
struct ata_ioports *ioaddr;
int i, rc;
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index c79f066..68eb349 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -847,15 +847,16 @@ static u32 hpt374_read_freq(struct pci_dev *pdev)
u32 freq;
unsigned long io_base = pci_resource_start(pdev, 4);
if (PCI_FUNC(pdev->devfn) & 1) {
- struct pci_dev *pdev_0 = pci_get_slot(pdev->bus, pdev->devfn - 1);
+ struct pci_dev *pdev_0;
+
+ pdev_0 = pci_get_slot(pdev->bus, pdev->devfn - 1);
/* Someone hot plugged the controller on us ? */
if (pdev_0 == NULL)
return 0;
io_base = pci_resource_start(pdev_0, 4);
freq = inl(io_base + 0x90);
pci_dev_put(pdev_0);
- }
- else
+ } else
freq = inl(io_base + 0x90);
return freq;
}
diff --git a/drivers/ata/pata_icside.c b/drivers/ata/pata_icside.c
index 842fe08..5b8586d 100644
--- a/drivers/ata/pata_icside.c
+++ b/drivers/ata/pata_icside.c
@@ -224,6 +224,7 @@ static void pata_icside_bmdma_setup(struct ata_queued_cmd *qc)
struct pata_icside_state *state = ap->host->private_data;
struct scatterlist *sg, *rsg = state->sg;
unsigned int write = qc->tf.flags & ATA_TFLAG_WRITE;
+ unsigned int si;
/*
* We are simplex; BUG if we try to fiddle with DMA
@@ -234,7 +235,7 @@ static void pata_icside_bmdma_setup(struct ata_queued_cmd *qc)
/*
* Copy ATAs scattered sg list into a contiguous array of sg
*/
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
memcpy(rsg, sg, sizeof(*sg));
rsg++;
}
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
index ca9aae0..109ddd4 100644
--- a/drivers/ata/pata_it821x.c
+++ b/drivers/ata/pata_it821x.c
@@ -430,7 +430,7 @@ static unsigned int it821x_smart_qc_issue_prot(struct ata_queued_cmd *qc)
return ata_qc_issue_prot(qc);
}
printk(KERN_DEBUG "it821x: can't process command 0x%02X\n", qc->tf.command);
- return AC_ERR_INVALID;
+ return AC_ERR_DEV;
}
/**
@@ -516,6 +516,37 @@ static void it821x_dev_config(struct ata_device *adev)
printk("(%dK stripe)", adev->id[146]);
printk(".\n");
}
+ /* This is a controller firmware triggered funny, don't
+ report the drive faulty! */
+ adev->horkage &= ~ATA_HORKAGE_DIAGNOSTIC;
+}
+
+/**
+ * it821x_ident_hack - Hack identify data up
+ * @ap: Port
+ *
+ * Walk the devices on this firmware driven port and slightly
+ * mash the identify data to stop us and common tools trying to
+ * use features not firmware supported. The firmware itself does
+ * some masking (eg SMART) but not enough.
+ *
+ * This is a bit of an abuse of the cable method, but it is the
+ * only method called at the right time. We could modify the libata
+ * core specifically for ident hacking but while we have one offender
+ * it seems better to keep the fallout localised.
+ */
+
+static int it821x_ident_hack(struct ata_port *ap)
+{
+ struct ata_device *adev;
+ ata_link_for_each_dev(adev, &ap->link) {
+ if (ata_dev_enabled(adev)) {
+ adev->id[84] &= ~(1 << 6); /* No FUA */
+ adev->id[85] &= ~(1 << 10); /* No HPA */
+ adev->id[76] = 0; /* No NCQ/AN etc */
+ }
+ }
+ return ata_cable_unknown(ap);
}
@@ -634,7 +665,7 @@ static struct ata_port_operations it821x_smart_port_ops = {
.thaw = ata_bmdma_thaw,
.error_handler = ata_bmdma_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
- .cable_detect = ata_cable_unknown,
+ .cable_detect = it821x_ident_hack,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
diff --git a/drivers/ata/pata_ixp4xx_cf.c b/drivers/ata/pata_ixp4xx_cf.c
index 120b5bf..030878f 100644
--- a/drivers/ata/pata_ixp4xx_cf.c
+++ b/drivers/ata/pata_ixp4xx_cf.c
@@ -42,13 +42,13 @@ static int ixp4xx_set_mode(struct ata_link *link, struct ata_device **error)
return 0;
}
-static void ixp4xx_mmio_data_xfer(struct ata_device *adev, unsigned char *buf,
- unsigned int buflen, int write_data)
+static unsigned int ixp4xx_mmio_data_xfer(struct ata_device *dev,
+ unsigned char *buf, unsigned int buflen, int rw)
{
unsigned int i;
unsigned int words = buflen >> 1;
u16 *buf16 = (u16 *) buf;
- struct ata_port *ap = adev->link->ap;
+ struct ata_port *ap = dev->link->ap;
void __iomem *mmio = ap->ioaddr.data_addr;
struct ixp4xx_pata_data *data = ap->host->dev->platform_data;
@@ -59,30 +59,32 @@ static void ixp4xx_mmio_data_xfer(struct ata_device *adev, unsigned char *buf,
udelay(100);
/* Transfer multiple of 2 bytes */
- if (write_data) {
- for (i = 0; i < words; i++)
- writew(buf16[i], mmio);
- } else {
+ if (rw == READ)
for (i = 0; i < words; i++)
buf16[i] = readw(mmio);
- }
+ else
+ for (i = 0; i < words; i++)
+ writew(buf16[i], mmio);
/* Transfer trailing 1 byte, if any. */
if (unlikely(buflen & 0x01)) {
u16 align_buf[1] = { 0 };
unsigned char *trailing_buf = buf + buflen - 1;
- if (write_data) {
- memcpy(align_buf, trailing_buf, 1);
- writew(align_buf[0], mmio);
- } else {
+ if (rw == READ) {
align_buf[0] = readw(mmio);
memcpy(trailing_buf, align_buf, 1);
+ } else {
+ memcpy(align_buf, trailing_buf, 1);
+ writew(align_buf[0], mmio);
}
+ words++;
}
udelay(100);
*data->cs0_cfg |= 0x01;
+
+ return words << 1;
}
static struct scsi_host_template ixp4xx_sht = {
diff --git a/drivers/ata/pata_legacy.c b/drivers/ata/pata_legacy.c
index 17159b5..333dc15 100644
--- a/drivers/ata/pata_legacy.c
+++ b/drivers/ata/pata_legacy.c
@@ -28,7 +28,6 @@
*
* Unsupported but docs exist:
* Appian/Adaptec AIC25VL01/Cirrus Logic PD7220
- * Winbond W83759A
*
* This driver handles legacy (that is "ISA/VLB side") IDE ports found
* on PC class systems. There are three hybrid devices that are exceptions
@@ -36,7 +35,7 @@
* the MPIIX where the tuning is PCI side but the IDE is "ISA side".
*
* Specific support is included for the ht6560a/ht6560b/opti82c611a/
- * opti82c465mv/promise 20230c/20630
+ * opti82c465mv/promise 20230c/20630/winbond83759A
*
* Use the autospeed and pio_mask options with:
* Appian ADI/2 aka CLPD7220 or AIC25VL01.
@@ -47,9 +46,6 @@
* For now use autospeed and pio_mask as above with the W83759A. This may
* change.
*
- * TODO
- * Merge existing pata_qdi driver
- *
*/
#include <linux/kernel.h>
@@ -64,12 +60,13 @@
#include <linux/platform_device.h>
#define DRV_NAME "pata_legacy"
-#define DRV_VERSION "0.5.5"
+#define DRV_VERSION "0.6.5"
#define NR_HOST 6
-static int legacy_port[NR_HOST] = { 0x1f0, 0x170, 0x1e8, 0x168, 0x1e0, 0x160 };
-static int legacy_irq[NR_HOST] = { 14, 15, 11, 10, 8, 12 };
+static int all;
+module_param(all, int, 0444);
+MODULE_PARM_DESC(all, "Grab all legacy port devices, even if PCI(0=off, 1=on)");
struct legacy_data {
unsigned long timing;
@@ -80,21 +77,107 @@ struct legacy_data {
};
+enum controller {
+ BIOS = 0,
+ SNOOP = 1,
+ PDC20230 = 2,
+ HT6560A = 3,
+ HT6560B = 4,
+ OPTI611A = 5,
+ OPTI46X = 6,
+ QDI6500 = 7,
+ QDI6580 = 8,
+ QDI6580DP = 9, /* Dual channel mode is different */
+ W83759A = 10,
+
+ UNKNOWN = -1
+};
+
+
+struct legacy_probe {
+ unsigned char *name;
+ unsigned long port;
+ unsigned int irq;
+ unsigned int slot;
+ enum controller type;
+ unsigned long private;
+};
+
+struct legacy_controller {
+ const char *name;
+ struct ata_port_operations *ops;
+ unsigned int pio_mask;
+ unsigned int flags;
+ int (*setup)(struct platform_device *, struct legacy_probe *probe,
+ struct legacy_data *data);
+};
+
+static int legacy_port[NR_HOST] = { 0x1f0, 0x170, 0x1e8, 0x168, 0x1e0, 0x160 };
+
+static struct legacy_probe probe_list[NR_HOST];
static struct legacy_data legacy_data[NR_HOST];
static struct ata_host *legacy_host[NR_HOST];
static int nr_legacy_host;
-static int probe_all; /* Set to check all ISA port ranges */
-static int ht6560a; /* HT 6560A on primary 1, secondary 2, both 3 */
-static int ht6560b; /* HT 6560A on primary 1, secondary 2, both 3 */
-static int opti82c611a; /* Opti82c611A on primary 1, secondary 2, both 3 */
-static int opti82c46x; /* Opti 82c465MV present (pri/sec autodetect) */
-static int autospeed; /* Chip present which snoops speed changes */
-static int pio_mask = 0x1F; /* PIO range for autospeed devices */
+static int probe_all; /* Set to check all ISA port ranges */
+static int ht6560a; /* HT 6560A on primary 1, second 2, both 3 */
+static int ht6560b; /* HT 6560A on primary 1, second 2, both 3 */
+static int opti82c611a; /* Opti82c611A on primary 1, sec 2, both 3 */
+static int opti82c46x; /* Opti 82c465MV present(pri/sec autodetect) */
+static int qdi; /* Set to probe QDI controllers */
+static int winbond; /* Set to probe Winbond controllers,
+ give I/O port if non stdanard */
+static int autospeed; /* Chip present which snoops speed changes */
+static int pio_mask = 0x1F; /* PIO range for autospeed devices */
static int iordy_mask = 0xFFFFFFFF; /* Use iordy if available */
/**
+ * legacy_probe_add - Add interface to probe list
+ * @port: Controller port
+ * @irq: IRQ number
+ * @type: Controller type
+ * @private: Controller specific info
+ *
+ * Add an entry into the probe list for ATA controllers. This is used
+ * to add the default ISA slots and then to build up the table
+ * further according to other ISA/VLB/Weird device scans
+ *
+ * An I/O port list is used to keep ordering stable and sane, as we
+ * don't have any good way to talk about ordering otherwise
+ */
+
+static int legacy_probe_add(unsigned long port, unsigned int irq,
+ enum controller type, unsigned long private)
+{
+ struct legacy_probe *lp = &probe_list[0];
+ int i;
+ struct legacy_probe *free = NULL;
+
+ for (i = 0; i < NR_HOST; i++) {
+ if (lp->port == 0 && free == NULL)
+ free = lp;
+ /* Matching port, or the correct slot for ordering */
+ if (lp->port == port || legacy_port[i] == port) {
+ free = lp;
+ break;
+ }
+ lp++;
+ }
+ if (free == NULL) {
+ printk(KERN_ERR "pata_legacy: Too many interfaces.\n");
+ return -1;
+ }
+ /* Fill in the entry for later probing */
+ free->port = port;
+ free->irq = irq;
+ free->type = type;
+ free->private = private;
+ return 0;
+}
+
+
+/**
* legacy_set_mode - mode setting
* @link: IDE link
* @unused: Device that failed when error is returned
@@ -113,7 +196,8 @@ static int legacy_set_mode(struct ata_link *link, struct ata_device **unused)
ata_link_for_each_dev(dev, link) {
if (ata_dev_enabled(dev)) {
- ata_dev_printk(dev, KERN_INFO, "configured for PIO\n");
+ ata_dev_printk(dev, KERN_INFO,
+ "configured for PIO\n");
dev->pio_mode = XFER_PIO_0;
dev->xfer_mode = XFER_PIO_0;
dev->xfer_shift = ATA_SHIFT_PIO;
@@ -171,7 +255,7 @@ static struct ata_port_operations simple_port_ops = {
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
- .port_start = ata_port_start,
+ .port_start = ata_sff_port_start,
};
static struct ata_port_operations legacy_port_ops = {
@@ -198,15 +282,16 @@ static struct ata_port_operations legacy_port_ops = {
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
- .port_start = ata_port_start,
+ .port_start = ata_sff_port_start,
};
/*
* Promise 20230C and 20620 support
*
- * This controller supports PIO0 to PIO2. We set PIO timings conservatively to
- * allow for 50MHz Vesa Local Bus. The 20620 DMA support is weird being DMA to
- * controller and PIO'd to the host and not supported.
+ * This controller supports PIO0 to PIO2. We set PIO timings
+ * conservatively to allow for 50MHz Vesa Local Bus. The 20620 DMA
+ * support is weird being DMA to controller and PIO'd to the host
+ * and not supported.
*/
static void pdc20230_set_piomode(struct ata_port *ap, struct ata_device *adev)
@@ -221,8 +306,7 @@ static void pdc20230_set_piomode(struct ata_port *ap, struct ata_device *adev)
local_irq_save(flags);
/* Unlock the control interface */
- do
- {
+ do {
inb(0x1F5);
outb(inb(0x1F2) | 0x80, 0x1F2);
inb(0x1F2);
@@ -231,7 +315,7 @@ static void pdc20230_set_piomode(struct ata_port *ap, struct ata_device *adev)
inb(0x1F2);
inb(0x1F2);
}
- while((inb(0x1F2) & 0x80) && --tries);
+ while ((inb(0x1F2) & 0x80) && --tries);
local_irq_restore(flags);
@@ -249,13 +333,14 @@ static void pdc20230_set_piomode(struct ata_port *ap, struct ata_device *adev)
}
-static void pdc_data_xfer_vlb(struct ata_device *adev, unsigned char *buf, unsigned int buflen, int write_data)
+static unsigned int pdc_data_xfer_vlb(struct ata_device *dev,
+ unsigned char *buf, unsigned int buflen, int rw)
{
- struct ata_port *ap = adev->link->ap;
- int slop = buflen & 3;
- unsigned long flags;
+ if (ata_id_has_dword_io(dev->id)) {
+ struct ata_port *ap = dev->link->ap;
+ int slop = buflen & 3;
+ unsigned long flags;
- if (ata_id_has_dword_io(adev->id)) {
local_irq_save(flags);
/* Perform the 32bit I/O synchronization sequence */
@@ -264,26 +349,27 @@ static void pdc_data_xfer_vlb(struct ata_device *adev, unsigned char *buf, unsig
ioread8(ap->ioaddr.nsect_addr);
/* Now the data */
-
- if (write_data)
- iowrite32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
- else
+ if (rw == READ)
ioread32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
+ else
+ iowrite32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
if (unlikely(slop)) {
- __le32 pad = 0;
- if (write_data) {
- memcpy(&pad, buf + buflen - slop, slop);
- iowrite32(le32_to_cpu(pad), ap->ioaddr.data_addr);
- } else {
+ u32 pad;
+ if (rw == READ) {
pad = cpu_to_le32(ioread32(ap->ioaddr.data_addr));
memcpy(buf + buflen - slop, &pad, slop);
+ } else {
+ memcpy(&pad, buf + buflen - slop, slop);
+ iowrite32(le32_to_cpu(pad), ap->ioaddr.data_addr);
}
+ buflen += 4 - slop;
}
local_irq_restore(flags);
- }
- else
- ata_data_xfer_noirq(adev, buf, buflen, write_data);
+ } else
+ buflen = ata_data_xfer_noirq(dev, buf, buflen, rw);
+
+ return buflen;
}
static struct ata_port_operations pdc20230_port_ops = {
@@ -310,14 +396,14 @@ static struct ata_port_operations pdc20230_port_ops = {
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
- .port_start = ata_port_start,
+ .port_start = ata_sff_port_start,
};
/*
* Holtek 6560A support
*
- * This controller supports PIO0 to PIO2 (no IORDY even though higher timings
- * can be loaded).
+ * This controller supports PIO0 to PIO2 (no IORDY even though higher
+ * timings can be loaded).
*/
static void ht6560a_set_piomode(struct ata_port *ap, struct ata_device *adev)
@@ -364,14 +450,14 @@ static struct ata_port_operations ht6560a_port_ops = {
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
- .port_start = ata_port_start,
+ .port_start = ata_sff_port_start,
};
/*
* Holtek 6560B support
*
- * This controller supports PIO0 to PIO4. We honour the BIOS/jumper FIFO setting
- * unless we see an ATAPI device in which case we force it off.
+ * This controller supports PIO0 to PIO4. We honour the BIOS/jumper FIFO
+ * setting unless we see an ATAPI device in which case we force it off.
*
* FIXME: need to implement 2nd channel support.
*/
@@ -398,7 +484,7 @@ static void ht6560b_set_piomode(struct ata_port *ap, struct ata_device *adev)
if (adev->class != ATA_DEV_ATA) {
u8 rconf = inb(0x3E6);
if (rconf & 0x24) {
- rconf &= ~ 0x24;
+ rconf &= ~0x24;
outb(rconf, 0x3E6);
}
}
@@ -423,13 +509,13 @@ static struct ata_port_operations ht6560b_port_ops = {
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_data_xfer, /* FIXME: Check 32bit and noirq */
+ .data_xfer = ata_data_xfer, /* FIXME: Check 32bit and noirq */
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
- .port_start = ata_port_start,
+ .port_start = ata_sff_port_start,
};
/*
@@ -462,7 +548,8 @@ static u8 opti_syscfg(u8 reg)
* This controller supports PIO0 to PIO3.
*/
-static void opti82c611a_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void opti82c611a_set_piomode(struct ata_port *ap,
+ struct ata_device *adev)
{
u8 active, recover, setup;
struct ata_timing t;
@@ -549,7 +636,7 @@ static struct ata_port_operations opti82c611a_port_ops = {
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
- .port_start = ata_port_start,
+ .port_start = ata_sff_port_start,
};
/*
@@ -681,77 +768,398 @@ static struct ata_port_operations opti82c46x_port_ops = {
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
- .port_start = ata_port_start,
+ .port_start = ata_sff_port_start,
};
+static void qdi6500_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct ata_timing t;
+ struct legacy_data *qdi = ap->host->private_data;
+ int active, recovery;
+ u8 timing;
+
+ /* Get the timing data in cycles */
+ ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000);
+
+ if (qdi->fast) {
+ active = 8 - FIT(t.active, 1, 8);
+ recovery = 18 - FIT(t.recover, 3, 18);
+ } else {
+ active = 9 - FIT(t.active, 2, 9);
+ recovery = 15 - FIT(t.recover, 0, 15);
+ }
+ timing = (recovery << 4) | active | 0x08;
+
+ qdi->clock[adev->devno] = timing;
+
+ outb(timing, qdi->timing);
+}
/**
- * legacy_init_one - attach a legacy interface
- * @port: port number
- * @io: I/O port start
- * @ctrl: control port
+ * qdi6580dp_set_piomode - PIO setup for dual channel
+ * @ap: Port
+ * @adev: Device
* @irq: interrupt line
*
- * Register an ISA bus IDE interface. Such interfaces are PIO and we
- * assume do not support IRQ sharing.
+ * In dual channel mode the 6580 has one clock per channel and we have
+ * to software clockswitch in qc_issue_prot.
*/
-static __init int legacy_init_one(int port, unsigned long io, unsigned long ctrl, int irq)
+static void qdi6580dp_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
- struct legacy_data *ld = &legacy_data[nr_legacy_host];
- struct ata_host *host;
- struct ata_port *ap;
- struct platform_device *pdev;
- struct ata_port_operations *ops = &legacy_port_ops;
- void __iomem *io_addr, *ctrl_addr;
- int pio_modes = pio_mask;
- u32 mask = (1 << port);
- u32 iordy = (iordy_mask & mask) ? 0: ATA_FLAG_NO_IORDY;
- int ret;
+ struct ata_timing t;
+ struct legacy_data *qdi = ap->host->private_data;
+ int active, recovery;
+ u8 timing;
- pdev = platform_device_register_simple(DRV_NAME, nr_legacy_host, NULL, 0);
- if (IS_ERR(pdev))
- return PTR_ERR(pdev);
+ /* Get the timing data in cycles */
+ ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000);
+
+ if (qdi->fast) {
+ active = 8 - FIT(t.active, 1, 8);
+ recovery = 18 - FIT(t.recover, 3, 18);
+ } else {
+ active = 9 - FIT(t.active, 2, 9);
+ recovery = 15 - FIT(t.recover, 0, 15);
+ }
+ timing = (recovery << 4) | active | 0x08;
- ret = -EBUSY;
- if (devm_request_region(&pdev->dev, io, 8, "pata_legacy") == NULL ||
- devm_request_region(&pdev->dev, ctrl, 1, "pata_legacy") == NULL)
- goto fail;
+ qdi->clock[adev->devno] = timing;
- ret = -ENOMEM;
- io_addr = devm_ioport_map(&pdev->dev, io, 8);
- ctrl_addr = devm_ioport_map(&pdev->dev, ctrl, 1);
- if (!io_addr || !ctrl_addr)
- goto fail;
+ outb(timing, qdi->timing + 2 * ap->port_no);
+ /* Clear the FIFO */
+ if (adev->class != ATA_DEV_ATA)
+ outb(0x5F, qdi->timing + 3);
+}
- if (ht6560a & mask) {
- ops = &ht6560a_port_ops;
- pio_modes = 0x07;
- iordy = ATA_FLAG_NO_IORDY;
- }
- if (ht6560b & mask) {
- ops = &ht6560b_port_ops;
- pio_modes = 0x1F;
- }
- if (opti82c611a & mask) {
- ops = &opti82c611a_port_ops;
- pio_modes = 0x0F;
+/**
+ * qdi6580_set_piomode - PIO setup for single channel
+ * @ap: Port
+ * @adev: Device
+ *
+ * In single channel mode the 6580 has one clock per device and we can
+ * avoid the requirement to clock switch. We also have to load the timing
+ * into the right clock according to whether we are master or slave.
+ */
+
+static void qdi6580_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct ata_timing t;
+ struct legacy_data *qdi = ap->host->private_data;
+ int active, recovery;
+ u8 timing;
+
+ /* Get the timing data in cycles */
+ ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000);
+
+ if (qdi->fast) {
+ active = 8 - FIT(t.active, 1, 8);
+ recovery = 18 - FIT(t.recover, 3, 18);
+ } else {
+ active = 9 - FIT(t.active, 2, 9);
+ recovery = 15 - FIT(t.recover, 0, 15);
}
- if (opti82c46x & mask) {
- ops = &opti82c46x_port_ops;
- pio_modes = 0x0F;
+ timing = (recovery << 4) | active | 0x08;
+ qdi->clock[adev->devno] = timing;
+ outb(timing, qdi->timing + 2 * adev->devno);
+ /* Clear the FIFO */
+ if (adev->class != ATA_DEV_ATA)
+ outb(0x5F, qdi->timing + 3);
+}
+
+/**
+ * qdi_qc_issue_prot - command issue
+ * @qc: command pending
+ *
+ * Called when the libata layer is about to issue a command. We wrap
+ * this interface so that we can load the correct ATA timings.
+ */
+
+static unsigned int qdi_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct ata_device *adev = qc->dev;
+ struct legacy_data *qdi = ap->host->private_data;
+
+ if (qdi->clock[adev->devno] != qdi->last) {
+ if (adev->pio_mode) {
+ qdi->last = qdi->clock[adev->devno];
+ outb(qdi->clock[adev->devno], qdi->timing +
+ 2 * ap->port_no);
+ }
}
+ return ata_qc_issue_prot(qc);
+}
- /* Probe for automatically detectable controllers */
+static unsigned int vlb32_data_xfer(struct ata_device *adev, unsigned char *buf,
+ unsigned int buflen, int rw)
+{
+ struct ata_port *ap = adev->link->ap;
+ int slop = buflen & 3;
- if (io == 0x1F0 && ops == &legacy_port_ops) {
- unsigned long flags;
+ if (ata_id_has_dword_io(adev->id)) {
+ if (rw == WRITE)
+ iowrite32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
+ else
+ ioread32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
- local_irq_save(flags);
+ if (unlikely(slop)) {
+ u32 pad;
+ if (rw == WRITE) {
+ memcpy(&pad, buf + buflen - slop, slop);
+ pad = le32_to_cpu(pad);
+ iowrite32(pad, ap->ioaddr.data_addr);
+ } else {
+ pad = ioread32(ap->ioaddr.data_addr);
+ pad = cpu_to_le32(pad);
+ memcpy(buf + buflen - slop, &pad, slop);
+ }
+ }
+ return (buflen + 3) & ~3;
+ } else
+ return ata_data_xfer(adev, buf, buflen, rw);
+}
+
+static int qdi_port(struct platform_device *dev,
+ struct legacy_probe *lp, struct legacy_data *ld)
+{
+ if (devm_request_region(&dev->dev, lp->private, 4, "qdi") == NULL)
+ return -EBUSY;
+ ld->timing = lp->private;
+ return 0;
+}
+
+static struct ata_port_operations qdi6500_port_ops = {
+ .set_piomode = qdi6500_set_piomode,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = ata_bmdma_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = ata_cable_40wire,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = qdi_qc_issue_prot,
+
+ .data_xfer = vlb32_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+
+ .port_start = ata_sff_port_start,
+};
+
+static struct ata_port_operations qdi6580_port_ops = {
+ .set_piomode = qdi6580_set_piomode,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = ata_bmdma_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = ata_cable_40wire,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+
+ .data_xfer = vlb32_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+
+ .port_start = ata_sff_port_start,
+};
+
+static struct ata_port_operations qdi6580dp_port_ops = {
+ .set_piomode = qdi6580dp_set_piomode,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = ata_bmdma_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = ata_cable_40wire,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = qdi_qc_issue_prot,
+
+ .data_xfer = vlb32_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+
+ .port_start = ata_sff_port_start,
+};
+
+static DEFINE_SPINLOCK(winbond_lock);
+
+static void winbond_writecfg(unsigned long port, u8 reg, u8 val)
+{
+ unsigned long flags;
+ spin_lock_irqsave(&winbond_lock, flags);
+ outb(reg, port + 0x01);
+ outb(val, port + 0x02);
+ spin_unlock_irqrestore(&winbond_lock, flags);
+}
+
+static u8 winbond_readcfg(unsigned long port, u8 reg)
+{
+ u8 val;
+
+ unsigned long flags;
+ spin_lock_irqsave(&winbond_lock, flags);
+ outb(reg, port + 0x01);
+ val = inb(port + 0x02);
+ spin_unlock_irqrestore(&winbond_lock, flags);
+
+ return val;
+}
+
+static void winbond_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct ata_timing t;
+ struct legacy_data *winbond = ap->host->private_data;
+ int active, recovery;
+ u8 reg;
+ int timing = 0x88 + (ap->port_no * 4) + (adev->devno * 2);
+
+ reg = winbond_readcfg(winbond->timing, 0x81);
+
+ /* Get the timing data in cycles */
+ if (reg & 0x40) /* Fast VLB bus, assume 50MHz */
+ ata_timing_compute(adev, adev->pio_mode, &t, 20000, 1000);
+ else
+ ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000);
+
+ active = (FIT(t.active, 3, 17) - 1) & 0x0F;
+ recovery = (FIT(t.recover, 1, 15) + 1) & 0x0F;
+ timing = (active << 4) | recovery;
+ winbond_writecfg(winbond->timing, timing, reg);
+
+ /* Load the setup timing */
+
+ reg = 0x35;
+ if (adev->class != ATA_DEV_ATA)
+ reg |= 0x08; /* FIFO off */
+ if (!ata_pio_need_iordy(adev))
+ reg |= 0x02; /* IORDY off */
+ reg |= (FIT(t.setup, 0, 3) << 6);
+ winbond_writecfg(winbond->timing, timing + 1, reg);
+}
+
+static int winbond_port(struct platform_device *dev,
+ struct legacy_probe *lp, struct legacy_data *ld)
+{
+ if (devm_request_region(&dev->dev, lp->private, 4, "winbond") == NULL)
+ return -EBUSY;
+ ld->timing = lp->private;
+ return 0;
+}
+
+static struct ata_port_operations winbond_port_ops = {
+ .set_piomode = winbond_set_piomode,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = ata_bmdma_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = ata_cable_40wire,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+
+ .data_xfer = vlb32_data_xfer,
+
+ .irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .port_start = ata_sff_port_start,
+};
+
+static struct legacy_controller controllers[] = {
+ {"BIOS", &legacy_port_ops, 0x1F,
+ ATA_FLAG_NO_IORDY, NULL },
+ {"Snooping", &simple_port_ops, 0x1F,
+ 0 , NULL },
+ {"PDC20230", &pdc20230_port_ops, 0x7,
+ ATA_FLAG_NO_IORDY, NULL },
+ {"HT6560A", &ht6560a_port_ops, 0x07,
+ ATA_FLAG_NO_IORDY, NULL },
+ {"HT6560B", &ht6560b_port_ops, 0x1F,
+ ATA_FLAG_NO_IORDY, NULL },
+ {"OPTI82C611A", &opti82c611a_port_ops, 0x0F,
+ 0 , NULL },
+ {"OPTI82C46X", &opti82c46x_port_ops, 0x0F,
+ 0 , NULL },
+ {"QDI6500", &qdi6500_port_ops, 0x07,
+ ATA_FLAG_NO_IORDY, qdi_port },
+ {"QDI6580", &qdi6580_port_ops, 0x1F,
+ 0 , qdi_port },
+ {"QDI6580DP", &qdi6580dp_port_ops, 0x1F,
+ 0 , qdi_port },
+ {"W83759A", &winbond_port_ops, 0x1F,
+ 0 , winbond_port }
+};
+
+/**
+ * probe_chip_type - Discover controller
+ * @probe: Probe entry to check
+ *
+ * Probe an ATA port and identify the type of controller. We don't
+ * check if the controller appears to be driveless at this point.
+ */
+
+static __init int probe_chip_type(struct legacy_probe *probe)
+{
+ int mask = 1 << probe->slot;
+
+ if (winbond && (probe->port == 0x1F0 || probe->port == 0x170)) {
+ u8 reg = winbond_readcfg(winbond, 0x81);
+ reg |= 0x80; /* jumpered mode off */
+ winbond_writecfg(winbond, 0x81, reg);
+ reg = winbond_readcfg(winbond, 0x83);
+ reg |= 0xF0; /* local control */
+ winbond_writecfg(winbond, 0x83, reg);
+ reg = winbond_readcfg(winbond, 0x85);
+ reg |= 0xF0; /* programmable timing */
+ winbond_writecfg(winbond, 0x85, reg);
+
+ reg = winbond_readcfg(winbond, 0x81);
+
+ if (reg & mask)
+ return W83759A;
+ }
+ if (probe->port == 0x1F0) {
+ unsigned long flags;
+ local_irq_save(flags);
/* Probes */
- inb(0x1F5);
outb(inb(0x1F2) | 0x80, 0x1F2);
+ inb(0x1F5);
inb(0x1F2);
inb(0x3F6);
inb(0x3F6);
@@ -760,29 +1168,83 @@ static __init int legacy_init_one(int port, unsigned long io, unsigned long ctrl
if ((inb(0x1F2) & 0x80) == 0) {
/* PDC20230c or 20630 ? */
- printk(KERN_INFO "PDC20230-C/20630 VLB ATA controller detected.\n");
- pio_modes = 0x07;
- ops = &pdc20230_port_ops;
- iordy = ATA_FLAG_NO_IORDY;
+ printk(KERN_INFO "PDC20230-C/20630 VLB ATA controller"
+ " detected.\n");
udelay(100);
inb(0x1F5);
+ local_irq_restore(flags);
+ return PDC20230;
} else {
outb(0x55, 0x1F2);
inb(0x1F2);
inb(0x1F2);
- if (inb(0x1F2) == 0x00) {
- printk(KERN_INFO "PDC20230-B VLB ATA controller detected.\n");
- }
+ if (inb(0x1F2) == 0x00)
+ printk(KERN_INFO "PDC20230-B VLB ATA "
+ "controller detected.\n");
+ local_irq_restore(flags);
+ return BIOS;
}
local_irq_restore(flags);
}
+ if (ht6560a & mask)
+ return HT6560A;
+ if (ht6560b & mask)
+ return HT6560B;
+ if (opti82c611a & mask)
+ return OPTI611A;
+ if (opti82c46x & mask)
+ return OPTI46X;
+ if (autospeed & mask)
+ return SNOOP;
+ return BIOS;
+}
+
+
+/**
+ * legacy_init_one - attach a legacy interface
+ * @pl: probe record
+ *
+ * Register an ISA bus IDE interface. Such interfaces are PIO and we
+ * assume do not support IRQ sharing.
+ */
+
+static __init int legacy_init_one(struct legacy_probe *probe)
+{
+ struct legacy_controller *controller = &controllers[probe->type];
+ int pio_modes = controller->pio_mask;
+ unsigned long io = probe->port;
+ u32 mask = (1 << probe->slot);
+ struct ata_port_operations *ops = controller->ops;
+ struct legacy_data *ld = &legacy_data[probe->slot];
+ struct ata_host *host = NULL;
+ struct ata_port *ap;
+ struct platform_device *pdev;
+ struct ata_device *dev;
+ void __iomem *io_addr, *ctrl_addr;
+ u32 iordy = (iordy_mask & mask) ? 0: ATA_FLAG_NO_IORDY;
+ int ret;
- /* Chip does mode setting by command snooping */
- if (ops == &legacy_port_ops && (autospeed & mask))
- ops = &simple_port_ops;
+ iordy |= controller->flags;
+
+ pdev = platform_device_register_simple(DRV_NAME, probe->slot, NULL, 0);
+ if (IS_ERR(pdev))
+ return PTR_ERR(pdev);
+
+ ret = -EBUSY;
+ if (devm_request_region(&pdev->dev, io, 8, "pata_legacy") == NULL ||
+ devm_request_region(&pdev->dev, io + 0x0206, 1,
+ "pata_legacy") == NULL)
+ goto fail;
ret = -ENOMEM;
+ io_addr = devm_ioport_map(&pdev->dev, io, 8);
+ ctrl_addr = devm_ioport_map(&pdev->dev, io + 0x0206, 1);
+ if (!io_addr || !ctrl_addr)
+ goto fail;
+ if (controller->setup)
+ if (controller->setup(pdev, probe, ld) < 0)
+ goto fail;
host = ata_host_alloc(&pdev->dev, 1);
if (!host)
goto fail;
@@ -795,19 +1257,29 @@ static __init int legacy_init_one(int port, unsigned long io, unsigned long ctrl
ap->ioaddr.altstatus_addr = ctrl_addr;
ap->ioaddr.ctl_addr = ctrl_addr;
ata_std_ports(&ap->ioaddr);
- ap->private_data = ld;
+ ap->host->private_data = ld;
- ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx", io, ctrl);
+ ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx", io, io + 0x0206);
- ret = ata_host_activate(host, irq, ata_interrupt, 0, &legacy_sht);
+ ret = ata_host_activate(host, probe->irq, ata_interrupt, 0,
+ &legacy_sht);
if (ret)
goto fail;
-
- legacy_host[nr_legacy_host++] = dev_get_drvdata(&pdev->dev);
ld->platform_dev = pdev;
- return 0;
+ /* Nothing found means we drop the port as its probably not there */
+
+ ret = -ENODEV;
+ ata_link_for_each_dev(dev, &ap->link) {
+ if (!ata_dev_absent(dev)) {
+ legacy_host[probe->slot] = host;
+ ld->platform_dev = pdev;
+ return 0;
+ }
+ }
fail:
+ if (host)
+ ata_host_detach(host);
platform_device_unregister(pdev);
return ret;
}
@@ -818,13 +1290,15 @@ fail:
* @master: set this if we find an ATA master
* @master: set this if we find an ATA secondary
*
- * A small number of vendors implemented early PCI ATA interfaces on bridge logic
- * without the ATA interface being PCI visible. Where we have a matching PCI driver
- * we must skip the relevant device here. If we don't know about it then the legacy
- * driver is the right driver anyway.
+ * A small number of vendors implemented early PCI ATA interfaces
+ * on bridge logic without the ATA interface being PCI visible.
+ * Where we have a matching PCI driver we must skip the relevant
+ * device here. If we don't know about it then the legacy driver
+ * is the right driver anyway.
*/
-static void legacy_check_special_cases(struct pci_dev *p, int *primary, int *secondary)
+static void __init legacy_check_special_cases(struct pci_dev *p, int *primary,
+ int *secondary)
{
/* Cyrix CS5510 pre SFF MWDMA ATA on the bridge */
if (p->vendor == 0x1078 && p->device == 0x0000) {
@@ -840,7 +1314,8 @@ static void legacy_check_special_cases(struct pci_dev *p, int *primary, int *sec
if (p->vendor == 0x8086 && p->device == 0x1234) {
u16 r;
pci_read_config_word(p, 0x6C, &r);
- if (r & 0x8000) { /* ATA port enabled */
+ if (r & 0x8000) {
+ /* ATA port enabled */
if (r & 0x4000)
*secondary = 1;
else
@@ -850,6 +1325,114 @@ static void legacy_check_special_cases(struct pci_dev *p, int *primary, int *sec
}
}
+static __init void probe_opti_vlb(void)
+{
+ /* If an OPTI 82C46X is present find out where the channels are */
+ static const char *optis[4] = {
+ "3/463MV", "5MV",
+ "5MVA", "5MVB"
+ };
+ u8 chans = 1;
+ u8 ctrl = (opti_syscfg(0x30) & 0xC0) >> 6;
+
+ opti82c46x = 3; /* Assume master and slave first */
+ printk(KERN_INFO DRV_NAME ": Opti 82C46%s chipset support.\n",
+ optis[ctrl]);
+ if (ctrl == 3)
+ chans = (opti_syscfg(0x3F) & 0x20) ? 2 : 1;
+ ctrl = opti_syscfg(0xAC);
+ /* Check enabled and this port is the 465MV port. On the
+ MVB we may have two channels */
+ if (ctrl & 8) {
+ if (chans == 2) {
+ legacy_probe_add(0x1F0, 14, OPTI46X, 0);
+ legacy_probe_add(0x170, 15, OPTI46X, 0);
+ }
+ if (ctrl & 4)
+ legacy_probe_add(0x170, 15, OPTI46X, 0);
+ else
+ legacy_probe_add(0x1F0, 14, OPTI46X, 0);
+ } else
+ legacy_probe_add(0x1F0, 14, OPTI46X, 0);
+}
+
+static __init void qdi65_identify_port(u8 r, u8 res, unsigned long port)
+{
+ static const unsigned long ide_port[2] = { 0x170, 0x1F0 };
+ /* Check card type */
+ if ((r & 0xF0) == 0xC0) {
+ /* QD6500: single channel */
+ if (r & 8)
+ /* Disabled ? */
+ return;
+ legacy_probe_add(ide_port[r & 0x01], 14 + (r & 0x01),
+ QDI6500, port);
+ }
+ if (((r & 0xF0) == 0xA0) || (r & 0xF0) == 0x50) {
+ /* QD6580: dual channel */
+ if (!request_region(port + 2 , 2, "pata_qdi")) {
+ release_region(port, 2);
+ return;
+ }
+ res = inb(port + 3);
+ /* Single channel mode ? */
+ if (res & 1)
+ legacy_probe_add(ide_port[r & 0x01], 14 + (r & 0x01),
+ QDI6580, port);
+ else { /* Dual channel mode */
+ legacy_probe_add(0x1F0, 14, QDI6580DP, port);
+ /* port + 0x02, r & 0x04 */
+ legacy_probe_add(0x170, 15, QDI6580DP, port + 2);
+ }
+ release_region(port + 2, 2);
+ }
+}
+
+static __init void probe_qdi_vlb(void)
+{
+ unsigned long flags;
+ static const unsigned long qd_port[2] = { 0x30, 0xB0 };
+ int i;
+
+ /*
+ * Check each possible QD65xx base address
+ */
+
+ for (i = 0; i < 2; i++) {
+ unsigned long port = qd_port[i];
+ u8 r, res;
+
+
+ if (request_region(port, 2, "pata_qdi")) {
+ /* Check for a card */
+ local_irq_save(flags);
+ /* I have no h/w that needs this delay but it
+ is present in the historic code */
+ r = inb(port);
+ udelay(1);
+ outb(0x19, port);
+ udelay(1);
+ res = inb(port);
+ udelay(1);
+ outb(r, port);
+ udelay(1);
+ local_irq_restore(flags);
+
+ /* Fail */
+ if (res == 0x19) {
+ release_region(port, 2);
+ continue;
+ }
+ /* Passes the presence test */
+ r = inb(port + 1);
+ udelay(1);
+ /* Check port agrees with port set */
+ if ((r & 2) >> 1 == i)
+ qdi65_identify_port(r, res, port);
+ release_region(port, 2);
+ }
+ }
+}
/**
* legacy_init - attach legacy interfaces
@@ -867,15 +1450,17 @@ static __init int legacy_init(void)
int ct = 0;
int primary = 0;
int secondary = 0;
- int last_port = NR_HOST;
+ int pci_present = 0;
+ struct legacy_probe *pl = &probe_list[0];
+ int slot = 0;
struct pci_dev *p = NULL;
for_each_pci_dev(p) {
int r;
- /* Check for any overlap of the system ATA mappings. Native mode controllers
- stuck on these addresses or some devices in 'raid' mode won't be found by
- the storage class test */
+ /* Check for any overlap of the system ATA mappings. Native
+ mode controllers stuck on these addresses or some devices
+ in 'raid' mode won't be found by the storage class test */
for (r = 0; r < 6; r++) {
if (pci_resource_start(p, r) == 0x1f0)
primary = 1;
@@ -885,49 +1470,39 @@ static __init int legacy_init(void)
/* Check for special cases */
legacy_check_special_cases(p, &primary, &secondary);
- /* If PCI bus is present then don't probe for tertiary legacy ports */
- if (probe_all == 0)
- last_port = 2;
+ /* If PCI bus is present then don't probe for tertiary
+ legacy ports */
+ pci_present = 1;
}
- /* If an OPTI 82C46X is present find out where the channels are */
- if (opti82c46x) {
- static const char *optis[4] = {
- "3/463MV", "5MV",
- "5MVA", "5MVB"
- };
- u8 chans = 1;
- u8 ctrl = (opti_syscfg(0x30) & 0xC0) >> 6;
-
- opti82c46x = 3; /* Assume master and slave first */
- printk(KERN_INFO DRV_NAME ": Opti 82C46%s chipset support.\n", optis[ctrl]);
- if (ctrl == 3)
- chans = (opti_syscfg(0x3F) & 0x20) ? 2 : 1;
- ctrl = opti_syscfg(0xAC);
- /* Check enabled and this port is the 465MV port. On the
- MVB we may have two channels */
- if (ctrl & 8) {
- if (ctrl & 4)
- opti82c46x = 2; /* Slave */
- else
- opti82c46x = 1; /* Master */
- if (chans == 2)
- opti82c46x = 3; /* Master and Slave */
- } /* Slave only */
- else if (chans == 1)
- opti82c46x = 1;
+ if (winbond == 1)
+ winbond = 0x130; /* Default port, alt is 1B0 */
+
+ if (primary == 0 || all)
+ legacy_probe_add(0x1F0, 14, UNKNOWN, 0);
+ if (secondary == 0 || all)
+ legacy_probe_add(0x170, 15, UNKNOWN, 0);
+
+ if (probe_all || !pci_present) {
+ /* ISA/VLB extra ports */
+ legacy_probe_add(0x1E8, 11, UNKNOWN, 0);
+ legacy_probe_add(0x168, 10, UNKNOWN, 0);
+ legacy_probe_add(0x1E0, 8, UNKNOWN, 0);
+ legacy_probe_add(0x160, 12, UNKNOWN, 0);
}
- for (i = 0; i < last_port; i++) {
- /* Skip primary if we have seen a PCI one */
- if (i == 0 && primary == 1)
- continue;
- /* Skip secondary if we have seen a PCI one */
- if (i == 1 && secondary == 1)
+ if (opti82c46x)
+ probe_opti_vlb();
+ if (qdi)
+ probe_qdi_vlb();
+
+ for (i = 0; i < NR_HOST; i++, pl++) {
+ if (pl->port == 0)
continue;
- if (legacy_init_one(i, legacy_port[i],
- legacy_port[i] + 0x0206,
- legacy_irq[i]) == 0)
+ if (pl->type == UNKNOWN)
+ pl->type = probe_chip_type(pl);
+ pl->slot = slot++;
+ if (legacy_init_one(pl) == 0)
ct++;
}
if (ct != 0)
@@ -941,11 +1516,8 @@ static __exit void legacy_exit(void)
for (i = 0; i < nr_legacy_host; i++) {
struct legacy_data *ld = &legacy_data[i];
-
ata_host_detach(legacy_host[i]);
platform_device_unregister(ld->platform_dev);
- if (ld->timing)
- release_region(ld->timing, 2);
}
}
@@ -960,9 +1532,9 @@ module_param(ht6560a, int, 0);
module_param(ht6560b, int, 0);
module_param(opti82c611a, int, 0);
module_param(opti82c46x, int, 0);
+module_param(qdi, int, 0);
module_param(pio_mask, int, 0);
module_param(iordy_mask, int, 0);
module_init(legacy_init);
module_exit(legacy_exit);
-
diff --git a/drivers/ata/pata_mpc52xx.c b/drivers/ata/pata_mpc52xx.c
index 50c56e2..dc40162 100644
--- a/drivers/ata/pata_mpc52xx.c
+++ b/drivers/ata/pata_mpc52xx.c
@@ -364,7 +364,7 @@ mpc52xx_ata_probe(struct of_device *op, const struct of_device_id *match)
{
unsigned int ipb_freq;
struct resource res_mem;
- int ata_irq = NO_IRQ;
+ int ata_irq;
struct mpc52xx_ata __iomem *ata_regs;
struct mpc52xx_ata_priv *priv;
int rv;
diff --git a/drivers/ata/pata_ninja32.c b/drivers/ata/pata_ninja32.c
new file mode 100644
index 0000000..1c1b835
--- /dev/null
+++ b/drivers/ata/pata_ninja32.c
@@ -0,0 +1,214 @@
+/*
+ * pata_ninja32.c - Ninja32 PATA for new ATA layer
+ * (C) 2007 Red Hat Inc
+ * Alan Cox <alan@redhat.com>
+ *
+ * Note: The controller like many controllers has shared timings for
+ * PIO and DMA. We thus flip to the DMA timings in dma_start and flip back
+ * in the dma_stop function. Thus we actually don't need a set_dmamode
+ * method as the PIO method is always called and will set the right PIO
+ * timing parameters.
+ *
+ * The Ninja32 Cardbus is not a generic SFF controller. Instead it is
+ * laid out as follows off BAR 0. This is based upon Mark Lord's delkin
+ * driver and the extensive analysis done by the BSD developers, notably
+ * ITOH Yasufumi.
+ *
+ * Base + 0x00 IRQ Status
+ * Base + 0x01 IRQ control
+ * Base + 0x02 Chipset control
+ * Base + 0x04 VDMA and reset control + wait bits
+ * Base + 0x08 BMIMBA
+ * Base + 0x0C DMA Length
+ * Base + 0x10 Taskfile
+ * Base + 0x18 BMDMA Status ?
+ * Base + 0x1C
+ * Base + 0x1D Bus master control
+ * bit 0 = enable
+ * bit 1 = 0 write/1 read
+ * bit 2 = 1 sgtable
+ * bit 3 = go
+ * bit 4-6 wait bits
+ * bit 7 = done
+ * Base + 0x1E AltStatus
+ * Base + 0x1F timing register
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_ninja32"
+#define DRV_VERSION "0.0.1"
+
+
+/**
+ * ninja32_set_piomode - set initial PIO mode data
+ * @ap: ATA interface
+ * @adev: ATA device
+ *
+ * Called to do the PIO mode setup. Our timing registers are shared
+ * but we want to set the PIO timing by default.
+ */
+
+static void ninja32_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ static u16 pio_timing[5] = {
+ 0xd6, 0x85, 0x44, 0x33, 0x13
+ };
+ iowrite8(pio_timing[adev->pio_mode - XFER_PIO_0],
+ ap->ioaddr.bmdma_addr + 0x1f);
+ ap->private_data = adev;
+}
+
+
+static void ninja32_dev_select(struct ata_port *ap, unsigned int device)
+{
+ struct ata_device *adev = &ap->link.device[device];
+ if (ap->private_data != adev) {
+ iowrite8(0xd6, ap->ioaddr.bmdma_addr + 0x1f);
+ ata_std_dev_select(ap, device);
+ ninja32_set_piomode(ap, adev);
+ }
+}
+
+static struct scsi_host_template ninja32_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
+ .bios_param = ata_std_bios_param,
+};
+
+static struct ata_port_operations ninja32_port_ops = {
+ .set_piomode = ninja32_set_piomode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ninja32_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = ata_bmdma_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = ata_cable_40wire,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+
+ .data_xfer = ata_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+
+ .port_start = ata_sff_port_start,
+};
+
+static int ninja32_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+ struct ata_host *host;
+ struct ata_port *ap;
+ void __iomem *base;
+ int rc;
+
+ host = ata_host_alloc(&dev->dev, 1);
+ if (!host)
+ return -ENOMEM;
+ ap = host->ports[0];
+
+ /* Set up the PCI device */
+ rc = pcim_enable_device(dev);
+ if (rc)
+ return rc;
+ rc = pcim_iomap_regions(dev, 1 << 0, DRV_NAME);
+ if (rc == -EBUSY)
+ pcim_pin_device(dev);
+ if (rc)
+ return rc;
+
+ host->iomap = pcim_iomap_table(dev);
+ rc = pci_set_dma_mask(dev, ATA_DMA_MASK);
+ if (rc)
+ return rc;
+ rc = pci_set_consistent_dma_mask(dev, ATA_DMA_MASK);
+ if (rc)
+ return rc;
+ pci_set_master(dev);
+
+ /* Set up the register mappings */
+ base = host->iomap[0];
+ if (!base)
+ return -ENOMEM;
+ ap->ops = &ninja32_port_ops;
+ ap->pio_mask = 0x1F;
+ ap->flags |= ATA_FLAG_SLAVE_POSS;
+
+ ap->ioaddr.cmd_addr = base + 0x10;
+ ap->ioaddr.ctl_addr = base + 0x1E;
+ ap->ioaddr.altstatus_addr = base + 0x1E;
+ ap->ioaddr.bmdma_addr = base;
+ ata_std_ports(&ap->ioaddr);
+
+ iowrite8(0x05, base + 0x01); /* Enable interrupt lines */
+ iowrite8(0xB3, base + 0x02); /* Burst, ?? setup */
+ iowrite8(0x00, base + 0x04); /* WAIT0 ? */
+ /* FIXME: Should we disable them at remove ? */
+ return ata_host_activate(host, dev->irq, ata_interrupt,
+ IRQF_SHARED, &ninja32_sht);
+}
+
+static const struct pci_device_id ninja32[] = {
+ { 0x1145, 0xf021, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+ { 0x1145, 0xf024, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+ { },
+};
+
+static struct pci_driver ninja32_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = ninja32,
+ .probe = ninja32_init_one,
+ .remove = ata_pci_remove_one
+};
+
+static int __init ninja32_init(void)
+{
+ return pci_register_driver(&ninja32_pci_driver);
+}
+
+static void __exit ninja32_exit(void)
+{
+ pci_unregister_driver(&ninja32_pci_driver);
+}
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for Ninja32 ATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, ninja32);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(ninja32_init);
+module_exit(ninja32_exit);
diff --git a/drivers/ata/pata_pcmcia.c b/drivers/ata/pata_pcmcia.c
index fd36099..3e7f6a9 100644
--- a/drivers/ata/pata_pcmcia.c
+++ b/drivers/ata/pata_pcmcia.c
@@ -42,7 +42,7 @@
#define DRV_NAME "pata_pcmcia"
-#define DRV_VERSION "0.3.2"
+#define DRV_VERSION "0.3.3"
/*
* Private data structure to glue stuff together
@@ -86,6 +86,47 @@ static int pcmcia_set_mode(struct ata_link *link, struct ata_device **r_failed_d
return ata_do_set_mode(link, r_failed_dev);
}
+/**
+ * pcmcia_set_mode_8bit - PCMCIA specific mode setup
+ * @link: link
+ * @r_failed_dev: Return pointer for failed device
+ *
+ * For the simple emulated 8bit stuff the less we do the better.
+ */
+
+static int pcmcia_set_mode_8bit(struct ata_link *link,
+ struct ata_device **r_failed_dev)
+{
+ return 0;
+}
+
+/**
+ * ata_data_xfer_8bit - Transfer data by 8bit PIO
+ * @dev: device to target
+ * @buf: data buffer
+ * @buflen: buffer length
+ * @rw: read/write
+ *
+ * Transfer data from/to the device data register by 8 bit PIO.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+
+static unsigned int ata_data_xfer_8bit(struct ata_device *dev,
+ unsigned char *buf, unsigned int buflen, int rw)
+{
+ struct ata_port *ap = dev->link->ap;
+
+ if (rw == READ)
+ ioread8_rep(ap->ioaddr.data_addr, buf, buflen);
+ else
+ iowrite8_rep(ap->ioaddr.data_addr, buf, buflen);
+
+ return buflen;
+}
+
+
static struct scsi_host_template pcmcia_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
@@ -129,6 +170,31 @@ static struct ata_port_operations pcmcia_port_ops = {
.port_start = ata_sff_port_start,
};
+static struct ata_port_operations pcmcia_8bit_port_ops = {
+ .set_mode = pcmcia_set_mode_8bit,
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = ata_bmdma_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = ata_cable_40wire,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+
+ .data_xfer = ata_data_xfer_8bit,
+
+ .irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+
+ .port_start = ata_sff_port_start,
+};
+
#define CS_CHECK(fn, ret) \
do { last_fn = (fn); if ((last_ret = (ret)) != 0) goto cs_failed; } while (0)
@@ -153,9 +219,12 @@ static int pcmcia_init_one(struct pcmcia_device *pdev)
cistpl_cftable_entry_t dflt;
} *stk = NULL;
cistpl_cftable_entry_t *cfg;
- int pass, last_ret = 0, last_fn = 0, is_kme = 0, ret = -ENOMEM;
+ int pass, last_ret = 0, last_fn = 0, is_kme = 0, ret = -ENOMEM, p;
unsigned long io_base, ctl_base;
void __iomem *io_addr, *ctl_addr;
+ int n_ports = 1;
+
+ struct ata_port_operations *ops = &pcmcia_port_ops;
info = kzalloc(sizeof(*info), GFP_KERNEL);
if (info == NULL)
@@ -282,27 +351,32 @@ next_entry:
/* FIXME: Could be more ports at base + 0x10 but we only deal with
one right now */
if (pdev->io.NumPorts1 >= 0x20)
- printk(KERN_WARNING DRV_NAME ": second channel not yet supported.\n");
+ n_ports = 2;
+ if (pdev->manf_id == 0x0097 && pdev->card_id == 0x1620)
+ ops = &pcmcia_8bit_port_ops;
/*
* Having done the PCMCIA plumbing the ATA side is relatively
* sane.
*/
ret = -ENOMEM;
- host = ata_host_alloc(&pdev->dev, 1);
+ host = ata_host_alloc(&pdev->dev, n_ports);
if (!host)
goto failed;
- ap = host->ports[0];
- ap->ops = &pcmcia_port_ops;
- ap->pio_mask = 1; /* ISA so PIO 0 cycles */
- ap->flags |= ATA_FLAG_SLAVE_POSS;
- ap->ioaddr.cmd_addr = io_addr;
- ap->ioaddr.altstatus_addr = ctl_addr;
- ap->ioaddr.ctl_addr = ctl_addr;
- ata_std_ports(&ap->ioaddr);
+ for (p = 0; p < n_ports; p++) {
+ ap = host->ports[p];
- ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx", io_base, ctl_base);
+ ap->ops = ops;
+ ap->pio_mask = 1; /* ISA so PIO 0 cycles */
+ ap->flags |= ATA_FLAG_SLAVE_POSS;
+ ap->ioaddr.cmd_addr = io_addr + 0x10 * p;
+ ap->ioaddr.altstatus_addr = ctl_addr + 0x10 * p;
+ ap->ioaddr.ctl_addr = ctl_addr + 0x10 * p;
+ ata_std_ports(&ap->ioaddr);
+
+ ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx", io_base, ctl_base);
+ }
/* activate */
ret = ata_host_activate(host, pdev->irq.AssignedIRQ, ata_interrupt,
@@ -360,6 +434,7 @@ static struct pcmcia_device_id pcmcia_devices[] = {
PCMCIA_DEVICE_MANF_CARD(0x0032, 0x0704),
PCMCIA_DEVICE_MANF_CARD(0x0032, 0x2904),
PCMCIA_DEVICE_MANF_CARD(0x0045, 0x0401), /* SanDisk CFA */
+ PCMCIA_DEVICE_MANF_CARD(0x0097, 0x1620), /* TI emulated */
PCMCIA_DEVICE_MANF_CARD(0x0098, 0x0000), /* Toshiba */
PCMCIA_DEVICE_MANF_CARD(0x00a4, 0x002d),
PCMCIA_DEVICE_MANF_CARD(0x00ce, 0x0000), /* Samsung */
diff --git a/drivers/ata/pata_pdc2027x.c b/drivers/ata/pata_pdc2027x.c
index 2622577..028af5d 100644
--- a/drivers/ata/pata_pdc2027x.c
+++ b/drivers/ata/pata_pdc2027x.c
@@ -348,7 +348,7 @@ static unsigned long pdc2027x_mode_filter(struct ata_device *adev, unsigned long
ata_id_c_string(pair->id, model_num, ATA_ID_PROD,
ATA_ID_PROD_LEN + 1);
/* If the master is a maxtor in UDMA6 then the slave should not use UDMA 6 */
- if (strstr(model_num, "Maxtor") == 0 && pair->dma_mode == XFER_UDMA_6)
+ if (strstr(model_num, "Maxtor") == NULL && pair->dma_mode == XFER_UDMA_6)
mask &= ~ (1 << (6 + ATA_SHIFT_UDMA));
return ata_pci_default_filter(adev, mask);
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c
index 6c9689b..3ed8667 100644
--- a/drivers/ata/pata_pdc202xx_old.c
+++ b/drivers/ata/pata_pdc202xx_old.c
@@ -168,8 +168,7 @@ static void pdc2026x_bmdma_start(struct ata_queued_cmd *qc)
pdc202xx_set_dmamode(ap, qc->dev);
/* Cases the state machine will not complete correctly without help */
- if ((tf->flags & ATA_TFLAG_LBA48) || tf->protocol == ATA_PROT_ATAPI_DMA)
- {
+ if ((tf->flags & ATA_TFLAG_LBA48) || tf->protocol == ATAPI_PROT_DMA) {
len = qc->nbytes / 2;
if (tf->flags & ATA_TFLAG_WRITE)
@@ -208,7 +207,7 @@ static void pdc2026x_bmdma_stop(struct ata_queued_cmd *qc)
void __iomem *atapi_reg = master + 0x20 + (4 * ap->port_no);
/* Cases the state machine will not complete correctly */
- if (tf->protocol == ATA_PROT_ATAPI_DMA || ( tf->flags & ATA_TFLAG_LBA48)) {
+ if (tf->protocol == ATAPI_PROT_DMA || (tf->flags & ATA_TFLAG_LBA48)) {
iowrite32(0, atapi_reg);
iowrite8(ioread8(clock) & ~sel66, clock);
}
diff --git a/drivers/ata/pata_qdi.c b/drivers/ata/pata_qdi.c
index a4c0e50..9f308ed 100644
--- a/drivers/ata/pata_qdi.c
+++ b/drivers/ata/pata_qdi.c
@@ -124,29 +124,33 @@ static unsigned int qdi_qc_issue_prot(struct ata_queued_cmd *qc)
return ata_qc_issue_prot(qc);
}
-static void qdi_data_xfer(struct ata_device *adev, unsigned char *buf, unsigned int buflen, int write_data)
+static unsigned int qdi_data_xfer(struct ata_device *dev, unsigned char *buf,
+ unsigned int buflen, int rw)
{
- struct ata_port *ap = adev->link->ap;
- int slop = buflen & 3;
+ if (ata_id_has_dword_io(dev->id)) {
+ struct ata_port *ap = dev->link->ap;
+ int slop = buflen & 3;
- if (ata_id_has_dword_io(adev->id)) {
- if (write_data)
- iowrite32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
- else
+ if (rw == READ)
ioread32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
+ else
+ iowrite32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
if (unlikely(slop)) {
- __le32 pad = 0;
- if (write_data) {
- memcpy(&pad, buf + buflen - slop, slop);
- iowrite32(le32_to_cpu(pad), ap->ioaddr.data_addr);
- } else {
+ u32 pad;
+ if (rw == READ) {
pad = cpu_to_le32(ioread32(ap->ioaddr.data_addr));
memcpy(buf + buflen - slop, &pad, slop);
+ } else {
+ memcpy(&pad, buf + buflen - slop, slop);
+ iowrite32(le32_to_cpu(pad), ap->ioaddr.data_addr);
}
+ buflen += 4 - slop;
}
} else
- ata_data_xfer(adev, buf, buflen, write_data);
+ buflen = ata_data_xfer(dev, buf, buflen, rw);
+
+ return buflen;
}
static struct scsi_host_template qdi_sht = {
diff --git a/drivers/ata/pata_scc.c b/drivers/ata/pata_scc.c
index ea2ef9f..55055b2 100644
--- a/drivers/ata/pata_scc.c
+++ b/drivers/ata/pata_scc.c
@@ -768,45 +768,47 @@ static u8 scc_bmdma_status (struct ata_port *ap)
/**
* scc_data_xfer - Transfer data by PIO
- * @adev: device for this I/O
+ * @dev: device for this I/O
* @buf: data buffer
* @buflen: buffer length
- * @write_data: read/write
+ * @rw: read/write
*
* Note: Original code is ata_data_xfer().
*/
-static void scc_data_xfer (struct ata_device *adev, unsigned char *buf,
- unsigned int buflen, int write_data)
+static unsigned int scc_data_xfer (struct ata_device *dev, unsigned char *buf,
+ unsigned int buflen, int rw)
{
- struct ata_port *ap = adev->link->ap;
+ struct ata_port *ap = dev->link->ap;
unsigned int words = buflen >> 1;
unsigned int i;
u16 *buf16 = (u16 *) buf;
void __iomem *mmio = ap->ioaddr.data_addr;
/* Transfer multiple of 2 bytes */
- if (write_data) {
- for (i = 0; i < words; i++)
- out_be32(mmio, cpu_to_le16(buf16[i]));
- } else {
+ if (rw == READ)
for (i = 0; i < words; i++)
buf16[i] = le16_to_cpu(in_be32(mmio));
- }
+ else
+ for (i = 0; i < words; i++)
+ out_be32(mmio, cpu_to_le16(buf16[i]));
/* Transfer trailing 1 byte, if any. */
if (unlikely(buflen & 0x01)) {
u16 align_buf[1] = { 0 };
unsigned char *trailing_buf = buf + buflen - 1;
- if (write_data) {
- memcpy(align_buf, trailing_buf, 1);
- out_be32(mmio, cpu_to_le16(align_buf[0]));
- } else {
+ if (rw == READ) {
align_buf[0] = le16_to_cpu(in_be32(mmio));
memcpy(trailing_buf, align_buf, 1);
+ } else {
+ memcpy(align_buf, trailing_buf, 1);
+ out_be32(mmio, cpu_to_le16(align_buf[0]));
}
+ words++;
}
+
+ return words << 1;
}
/**
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c
index 8bed888..9c523fb 100644
--- a/drivers/ata/pata_serverworks.c
+++ b/drivers/ata/pata_serverworks.c
@@ -41,7 +41,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_serverworks"
-#define DRV_VERSION "0.4.2"
+#define DRV_VERSION "0.4.3"
#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
#define SVWKS_CSB6_REVISION 0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
@@ -102,7 +102,7 @@ static int osb4_cable(struct ata_port *ap) {
}
/**
- * csb4_cable - CSB5/6 cable detect
+ * csb_cable - CSB5/6 cable detect
* @ap: ATA port to check
*
* Serverworks default arrangement is to use the drive side detection
@@ -110,7 +110,7 @@ static int osb4_cable(struct ata_port *ap) {
*/
static int csb_cable(struct ata_port *ap) {
- return ATA_CBL_PATA80;
+ return ATA_CBL_PATA_UNK;
}
struct sv_cable_table {
@@ -231,7 +231,6 @@ static unsigned long serverworks_csb_filter(struct ata_device *adev, unsigned lo
return ata_pci_default_filter(adev, mask);
}
-
/**
* serverworks_set_piomode - set initial PIO mode data
* @ap: ATA interface
@@ -243,7 +242,7 @@ static unsigned long serverworks_csb_filter(struct ata_device *adev, unsigned lo
static void serverworks_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
static const u8 pio_mode[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
- int offset = 1 + (2 * ap->port_no) - adev->devno;
+ int offset = 1 + 2 * ap->port_no - adev->devno;
int devbits = (2 * ap->port_no + adev->devno) * 4;
u16 csb5_pio;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 453d72b..39627ab 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -185,7 +185,8 @@ static int via_cable_detect(struct ata_port *ap) {
if (ata66 & (0x10100000 >> (16 * ap->port_no)))
return ATA_CBL_PATA80;
/* Check with ACPI so we can spot BIOS reported SATA bridges */
- if (ata_acpi_cbl_80wire(ap))
+ if (ata_acpi_init_gtm(ap) &&
+ ata_acpi_cbl_80wire(ap, ata_acpi_init_gtm(ap)))
return ATA_CBL_PATA80;
return ATA_CBL_PATA40;
}
diff --git a/drivers/ata/pata_winbond.c b/drivers/ata/pata_winbond.c
index 7116a9e..99c92ed 100644
--- a/drivers/ata/pata_winbond.c
+++ b/drivers/ata/pata_winbond.c
@@ -92,29 +92,33 @@ static void winbond_set_piomode(struct ata_port *ap, struct ata_device *adev)
}
-static void winbond_data_xfer(struct ata_device *adev, unsigned char *buf, unsigned int buflen, int write_data)
+static unsigned int winbond_data_xfer(struct ata_device *dev,
+ unsigned char *buf, unsigned int buflen, int rw)
{
- struct ata_port *ap = adev->link->ap;
+ struct ata_port *ap = dev->link->ap;
int slop = buflen & 3;
- if (ata_id_has_dword_io(adev->id)) {
- if (write_data)
- iowrite32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
- else
+ if (ata_id_has_dword_io(dev->id)) {
+ if (rw == READ)
ioread32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
+ else
+ iowrite32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
if (unlikely(slop)) {
- __le32 pad = 0;
- if (write_data) {
- memcpy(&pad, buf + buflen - slop, slop);
- iowrite32(le32_to_cpu(pad), ap->ioaddr.data_addr);
- } else {
+ u32 pad;
+ if (rw == READ) {
pad = cpu_to_le32(ioread32(ap->ioaddr.data_addr));
memcpy(buf + buflen - slop, &pad, slop);
+ } else {
+ memcpy(&pad, buf + buflen - slop, slop);
+ iowrite32(le32_to_cpu(pad), ap->ioaddr.data_addr);
}
+ buflen += 4 - slop;
}
} else
- ata_data_xfer(adev, buf, buflen, write_data);
+ buflen = ata_data_xfer(dev, buf, buflen, rw);
+
+ return buflen;
}
static struct scsi_host_template winbond_sht = {
@@ -191,7 +195,7 @@ static __init int winbond_init_one(unsigned long port)
reg = winbond_readcfg(port, 0x81);
if (!(reg & 0x03)) /* Disabled */
- return 0;
+ return -ENODEV;
for (i = 0; i < 2 ; i ++) {
unsigned long cmd_port = 0x1F0 - (0x80 * i);
diff --git a/drivers/ata/pdc_adma.c b/drivers/ata/pdc_adma.c
index bd4c2a3..8e1b7e9 100644
--- a/drivers/ata/pdc_adma.c
+++ b/drivers/ata/pdc_adma.c
@@ -321,8 +321,9 @@ static int adma_fill_sg(struct ata_queued_cmd *qc)
u8 *buf = pp->pkt, *last_buf = NULL;
int i = (2 + buf[3]) * 8;
u8 pFLAGS = pORD | ((qc->tf.flags & ATA_TFLAG_WRITE) ? pDIRO : 0);
+ unsigned int si;
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
u32 addr;
u32 len;
@@ -455,7 +456,7 @@ static unsigned int adma_qc_issue(struct ata_queued_cmd *qc)
adma_packet_start(qc);
return 0;
- case ATA_PROT_ATAPI_DMA:
+ case ATAPI_PROT_DMA:
BUG();
break;
diff --git a/drivers/ata/sata_fsl.c b/drivers/ata/sata_fsl.c
index d015b4a..922d7b2 100644
--- a/drivers/ata/sata_fsl.c
+++ b/drivers/ata/sata_fsl.c
@@ -333,13 +333,14 @@ static unsigned int sata_fsl_fill_sg(struct ata_queued_cmd *qc, void *cmd_desc,
struct prde *prd_ptr_to_indirect_ext = NULL;
unsigned indirect_ext_segment_sz = 0;
dma_addr_t indirect_ext_segment_paddr;
+ unsigned int si;
VPRINTK("SATA FSL : cd = 0x%x, prd = 0x%x\n", cmd_desc, prd);
indirect_ext_segment_paddr = cmd_desc_paddr +
SATA_FSL_CMD_DESC_OFFSET_TO_PRDT + SATA_FSL_MAX_PRD_DIRECT * 16;
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
dma_addr_t sg_addr = sg_dma_address(sg);
u32 sg_len = sg_dma_len(sg);
@@ -417,7 +418,7 @@ static void sata_fsl_qc_prep(struct ata_queued_cmd *qc)
}
/* setup "ACMD - atapi command" in cmd. desc. if this is ATAPI cmd */
- if (is_atapi_taskfile(&qc->tf)) {
+ if (ata_is_atapi(qc->tf.protocol)) {
desc_info |= ATAPI_CMD;
memset((void *)&cd->acmd, 0, 32);
memcpy((void *)&cd->acmd, qc->cdb, qc->dev->cdb_len);
diff --git a/drivers/ata/sata_inic162x.c b/drivers/ata/sata_inic162x.c
index 323c087..96e614a 100644
--- a/drivers/ata/sata_inic162x.c
+++ b/drivers/ata/sata_inic162x.c
@@ -585,7 +585,7 @@ static struct ata_port_operations inic_port_ops = {
};
static struct ata_port_info inic_port_info = {
- /* For some reason, ATA_PROT_ATAPI is broken on this
+ /* For some reason, ATAPI_PROT_PIO is broken on this
* controller, and no, PIO_POLLING does't fix it. It somehow
* manages to report the wrong ireason and ignoring ireason
* results in machine lock up. Tell libata to always prefer
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 37b850a..7e72463 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -1136,9 +1136,10 @@ static void mv_fill_sg(struct ata_queued_cmd *qc)
struct mv_port_priv *pp = qc->ap->private_data;
struct scatterlist *sg;
struct mv_sg *mv_sg, *last_sg = NULL;
+ unsigned int si;
mv_sg = pp->sg_tbl;
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
dma_addr_t addr = sg_dma_address(sg);
u32 sg_len = sg_dma_len(sg);
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index ed5dc7c..a0f98fd 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -1336,21 +1336,18 @@ static void nv_adma_fill_aprd(struct ata_queued_cmd *qc,
static void nv_adma_fill_sg(struct ata_queued_cmd *qc, struct nv_adma_cpb *cpb)
{
struct nv_adma_port_priv *pp = qc->ap->private_data;
- unsigned int idx;
struct nv_adma_prd *aprd;
struct scatterlist *sg;
+ unsigned int si;
VPRINTK("ENTER\n");
- idx = 0;
-
- ata_for_each_sg(sg, qc) {
- aprd = (idx < 5) ? &cpb->aprd[idx] :
- &pp->aprd[NV_ADMA_SGTBL_LEN * qc->tag + (idx-5)];
- nv_adma_fill_aprd(qc, sg, idx, aprd);
- idx++;
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
+ aprd = (si < 5) ? &cpb->aprd[si] :
+ &pp->aprd[NV_ADMA_SGTBL_LEN * qc->tag + (si-5)];
+ nv_adma_fill_aprd(qc, sg, si, aprd);
}
- if (idx > 5)
+ if (si > 5)
cpb->next_aprd = cpu_to_le64(((u64)(pp->aprd_dma + NV_ADMA_SGTBL_SZ * qc->tag)));
else
cpb->next_aprd = cpu_to_le64(0);
@@ -1995,17 +1992,14 @@ static void nv_swncq_fill_sg(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct scatterlist *sg;
- unsigned int idx;
struct nv_swncq_port_priv *pp = ap->private_data;
struct ata_prd *prd;
-
- WARN_ON(qc->__sg == NULL);
- WARN_ON(qc->n_elem == 0 && qc->pad_len == 0);
+ unsigned int si, idx;
prd = pp->prd + ATA_MAX_PRD * qc->tag;
idx = 0;
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
u32 addr, offset;
u32 sg_len, len;
@@ -2027,8 +2021,7 @@ static void nv_swncq_fill_sg(struct ata_queued_cmd *qc)
}
}
- if (idx)
- prd[idx - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
+ prd[idx - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
}
static unsigned int nv_swncq_issue_atacmd(struct ata_port *ap,
diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c
index 7914def..a07d319 100644
--- a/drivers/ata/sata_promise.c
+++ b/drivers/ata/sata_promise.c
@@ -450,19 +450,19 @@ static void pdc_atapi_pkt(struct ata_queued_cmd *qc)
struct pdc_port_priv *pp = ap->private_data;
u8 *buf = pp->pkt;
u32 *buf32 = (u32 *) buf;
- unsigned int dev_sel, feature, nbytes;
+ unsigned int dev_sel, feature;
/* set control bits (byte 0), zero delay seq id (byte 3),
* and seq id (byte 2)
*/
switch (qc->tf.protocol) {
- case ATA_PROT_ATAPI_DMA:
+ case ATAPI_PROT_DMA:
if (!(qc->tf.flags & ATA_TFLAG_WRITE))
buf32[0] = cpu_to_le32(PDC_PKT_READ);
else
buf32[0] = 0;
break;
- case ATA_PROT_ATAPI_NODATA:
+ case ATAPI_PROT_NODATA:
buf32[0] = cpu_to_le32(PDC_PKT_NODATA);
break;
default:
@@ -473,45 +473,37 @@ static void pdc_atapi_pkt(struct ata_queued_cmd *qc)
buf32[2] = 0; /* no next-packet */
/* select drive */
- if (sata_scr_valid(&ap->link)) {
+ if (sata_scr_valid(&ap->link))
dev_sel = PDC_DEVICE_SATA;
- } else {
- dev_sel = ATA_DEVICE_OBS;
- if (qc->dev->devno != 0)
- dev_sel |= ATA_DEV1;
- }
+ else
+ dev_sel = qc->tf.device;
+
buf[12] = (1 << 5) | ATA_REG_DEVICE;
buf[13] = dev_sel;
buf[14] = (1 << 5) | ATA_REG_DEVICE | PDC_PKT_CLEAR_BSY;
buf[15] = dev_sel; /* once more, waiting for BSY to clear */
buf[16] = (1 << 5) | ATA_REG_NSECT;
- buf[17] = 0x00;
+ buf[17] = qc->tf.nsect;
buf[18] = (1 << 5) | ATA_REG_LBAL;
- buf[19] = 0x00;
+ buf[19] = qc->tf.lbal;
/* set feature and byte counter registers */
- if (qc->tf.protocol != ATA_PROT_ATAPI_DMA) {
+ if (qc->tf.protocol != ATAPI_PROT_DMA)
feature = PDC_FEATURE_ATAPI_PIO;
- /* set byte counter register to real transfer byte count */
- nbytes = qc->nbytes;
- if (nbytes > 0xffff)
- nbytes = 0xffff;
- } else {
+ else
feature = PDC_FEATURE_ATAPI_DMA;
- /* set byte counter register to 0 */
- nbytes = 0;
- }
+
buf[20] = (1 << 5) | ATA_REG_FEATURE;
buf[21] = feature;
buf[22] = (1 << 5) | ATA_REG_BYTEL;
- buf[23] = nbytes & 0xFF;
+ buf[23] = qc->tf.lbam;
buf[24] = (1 << 5) | ATA_REG_BYTEH;
- buf[25] = (nbytes >> 8) & 0xFF;
+ buf[25] = qc->tf.lbah;
/* send ATAPI packet command 0xA0 */
buf[26] = (1 << 5) | ATA_REG_CMD;
- buf[27] = ATA_CMD_PACKET;
+ buf[27] = qc->tf.command;
/* select drive and check DRQ */
buf[28] = (1 << 5) | ATA_REG_DEVICE | PDC_PKT_WAIT_DRDY;
@@ -541,17 +533,15 @@ static void pdc_fill_sg(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct scatterlist *sg;
- unsigned int idx;
const u32 SG_COUNT_ASIC_BUG = 41*4;
+ unsigned int si, idx;
+ u32 len;
if (!(qc->flags & ATA_QCFLAG_DMAMAP))
return;
- WARN_ON(qc->__sg == NULL);
- WARN_ON(qc->n_elem == 0 && qc->pad_len == 0);
-
idx = 0;
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
u32 addr, offset;
u32 sg_len, len;
@@ -578,29 +568,27 @@ static void pdc_fill_sg(struct ata_queued_cmd *qc)
}
}
- if (idx) {
- u32 len = le32_to_cpu(ap->prd[idx - 1].flags_len);
+ len = le32_to_cpu(ap->prd[idx - 1].flags_len);
- if (len > SG_COUNT_ASIC_BUG) {
- u32 addr;
+ if (len > SG_COUNT_ASIC_BUG) {
+ u32 addr;
- VPRINTK("Splitting last PRD.\n");
+ VPRINTK("Splitting last PRD.\n");
- addr = le32_to_cpu(ap->prd[idx - 1].addr);
- ap->prd[idx - 1].flags_len = cpu_to_le32(len - SG_COUNT_ASIC_BUG);
- VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", idx - 1, addr, SG_COUNT_ASIC_BUG);
+ addr = le32_to_cpu(ap->prd[idx - 1].addr);
+ ap->prd[idx - 1].flags_len = cpu_to_le32(len - SG_COUNT_ASIC_BUG);
+ VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", idx - 1, addr, SG_COUNT_ASIC_BUG);
- addr = addr + len - SG_COUNT_ASIC_BUG;
- len = SG_COUNT_ASIC_BUG;
- ap->prd[idx].addr = cpu_to_le32(addr);
- ap->prd[idx].flags_len = cpu_to_le32(len);
- VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", idx, addr, len);
+ addr = addr + len - SG_COUNT_ASIC_BUG;
+ len = SG_COUNT_ASIC_BUG;
+ ap->prd[idx].addr = cpu_to_le32(addr);
+ ap->prd[idx].flags_len = cpu_to_le32(len);
+ VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", idx, addr, len);
- idx++;
- }
-
- ap->prd[idx - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
+ idx++;
}
+
+ ap->prd[idx - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
}
static void pdc_qc_prep(struct ata_queued_cmd *qc)
@@ -627,14 +615,14 @@ static void pdc_qc_prep(struct ata_queued_cmd *qc)
pdc_pkt_footer(&qc->tf, pp->pkt, i);
break;
- case ATA_PROT_ATAPI:
+ case ATAPI_PROT_PIO:
pdc_fill_sg(qc);
break;
- case ATA_PROT_ATAPI_DMA:
+ case ATAPI_PROT_DMA:
pdc_fill_sg(qc);
/*FALLTHROUGH*/
- case ATA_PROT_ATAPI_NODATA:
+ case ATAPI_PROT_NODATA:
pdc_atapi_pkt(qc);
break;
@@ -754,8 +742,8 @@ static inline unsigned int pdc_host_intr(struct ata_port *ap,
switch (qc->tf.protocol) {
case ATA_PROT_DMA:
case ATA_PROT_NODATA:
- case ATA_PROT_ATAPI_DMA:
- case ATA_PROT_ATAPI_NODATA:
+ case ATAPI_PROT_DMA:
+ case ATAPI_PROT_NODATA:
qc->err_mask |= ac_err_mask(ata_wait_idle(ap));
ata_qc_complete(qc);
handled = 1;
@@ -900,7 +888,7 @@ static inline void pdc_packet_start(struct ata_queued_cmd *qc)
static unsigned int pdc_qc_issue_prot(struct ata_queued_cmd *qc)
{
switch (qc->tf.protocol) {
- case ATA_PROT_ATAPI_NODATA:
+ case ATAPI_PROT_NODATA:
if (qc->dev->flags & ATA_DFLAG_CDB_INTR)
break;
/*FALLTHROUGH*/
@@ -908,7 +896,7 @@ static unsigned int pdc_qc_issue_prot(struct ata_queued_cmd *qc)
if (qc->tf.flags & ATA_TFLAG_POLLING)
break;
/*FALLTHROUGH*/
- case ATA_PROT_ATAPI_DMA:
+ case ATAPI_PROT_DMA:
case ATA_PROT_DMA:
pdc_packet_start(qc);
return 0;
@@ -922,16 +910,14 @@ static unsigned int pdc_qc_issue_prot(struct ata_queued_cmd *qc)
static void pdc_tf_load_mmio(struct ata_port *ap, const struct ata_taskfile *tf)
{
- WARN_ON(tf->protocol == ATA_PROT_DMA ||
- tf->protocol == ATA_PROT_ATAPI_DMA);
+ WARN_ON(tf->protocol == ATA_PROT_DMA || tf->protocol == ATAPI_PROT_DMA);
ata_tf_load(ap, tf);
}
static void pdc_exec_command_mmio(struct ata_port *ap,
const struct ata_taskfile *tf)
{
- WARN_ON(tf->protocol == ATA_PROT_DMA ||
- tf->protocol == ATA_PROT_ATAPI_DMA);
+ WARN_ON(tf->protocol == ATA_PROT_DMA || tf->protocol == ATAPI_PROT_DMA);
ata_exec_command(ap, tf);
}
diff --git a/drivers/ata/sata_promise.h b/drivers/ata/sata_promise.h
index 6ee5e19..00d6000 100644
--- a/drivers/ata/sata_promise.h
+++ b/drivers/ata/sata_promise.h
@@ -46,7 +46,7 @@ static inline unsigned int pdc_pkt_header(struct ata_taskfile *tf,
unsigned int devno, u8 *buf)
{
u8 dev_reg;
- u32 *buf32 = (u32 *) buf;
+ __le32 *buf32 = (__le32 *) buf;
/* set control bits (byte 0), zero delay seq id (byte 3),
* and seq id (byte 2)
diff --git a/drivers/ata/sata_qstor.c b/drivers/ata/sata_qstor.c
index c68b241..91cc12c 100644
--- a/drivers/ata/sata_qstor.c
+++ b/drivers/ata/sata_qstor.c
@@ -287,14 +287,10 @@ static unsigned int qs_fill_sg(struct ata_queued_cmd *qc)
struct scatterlist *sg;
struct ata_port *ap = qc->ap;
struct qs_port_priv *pp = ap->private_data;
- unsigned int nelem;
u8 *prd = pp->pkt + QS_CPB_BYTES;
+ unsigned int si;
- WARN_ON(qc->__sg == NULL);
- WARN_ON(qc->n_elem == 0 && qc->pad_len == 0);
-
- nelem = 0;
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
u64 addr;
u32 len;
@@ -306,12 +302,11 @@ static unsigned int qs_fill_sg(struct ata_queued_cmd *qc)
*(__le32 *)prd = cpu_to_le32(len);
prd += sizeof(u64);
- VPRINTK("PRD[%u] = (0x%llX, 0x%X)\n", nelem,
+ VPRINTK("PRD[%u] = (0x%llX, 0x%X)\n", si,
(unsigned long long)addr, len);
- nelem++;
}
- return nelem;
+ return si;
}
static void qs_qc_prep(struct ata_queued_cmd *qc)
@@ -376,7 +371,7 @@ static unsigned int qs_qc_issue(struct ata_queued_cmd *qc)
qs_packet_start(qc);
return 0;
- case ATA_PROT_ATAPI_DMA:
+ case ATAPI_PROT_DMA:
BUG();
break;
diff --git a/drivers/ata/sata_sil.c b/drivers/ata/sata_sil.c
index f5119bf..0b8191b 100644
--- a/drivers/ata/sata_sil.c
+++ b/drivers/ata/sata_sil.c
@@ -416,15 +416,14 @@ static void sil_host_intr(struct ata_port *ap, u32 bmdma2)
*/
/* Check the ATA_DFLAG_CDB_INTR flag is enough here.
- * The flag was turned on only for atapi devices.
- * No need to check is_atapi_taskfile(&qc->tf) again.
+ * The flag was turned on only for atapi devices. No
+ * need to check ata_is_atapi(qc->tf.protocol) again.
*/
if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
goto err_hsm;
break;
case HSM_ST_LAST:
- if (qc->tf.protocol == ATA_PROT_DMA ||
- qc->tf.protocol == ATA_PROT_ATAPI_DMA) {
+ if (ata_is_dma(qc->tf.protocol)) {
/* clear DMA-Start bit */
ap->ops->bmdma_stop(qc);
@@ -451,8 +450,7 @@ static void sil_host_intr(struct ata_port *ap, u32 bmdma2)
/* kick HSM in the ass */
ata_hsm_move(ap, qc, status, 0);
- if (unlikely(qc->err_mask) && (qc->tf.protocol == ATA_PROT_DMA ||
- qc->tf.protocol == ATA_PROT_ATAPI_DMA))
+ if (unlikely(qc->err_mask) && ata_is_dma(qc->tf.protocol))
ata_ehi_push_desc(ehi, "BMDMA2 stat 0x%x", bmdma2);
return;
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index 864c1c1..b4b1f91 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -813,8 +813,9 @@ static inline void sil24_fill_sg(struct ata_queued_cmd *qc,
{
struct scatterlist *sg;
struct sil24_sge *last_sge = NULL;
+ unsigned int si;
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
sge->addr = cpu_to_le64(sg_dma_address(sg));
sge->cnt = cpu_to_le32(sg_dma_len(sg));
sge->flags = 0;
@@ -823,8 +824,7 @@ static inline void sil24_fill_sg(struct ata_queued_cmd *qc,
sge++;
}
- if (likely(last_sge))
- last_sge->flags = cpu_to_le32(SGE_TRM);
+ last_sge->flags = cpu_to_le32(SGE_TRM);
}
static int sil24_qc_defer(struct ata_queued_cmd *qc)
@@ -852,9 +852,7 @@ static int sil24_qc_defer(struct ata_queued_cmd *qc)
* set.
*
*/
- int is_excl = (prot == ATA_PROT_ATAPI ||
- prot == ATA_PROT_ATAPI_NODATA ||
- prot == ATA_PROT_ATAPI_DMA ||
+ int is_excl = (ata_is_atapi(prot) ||
(qc->flags & ATA_QCFLAG_RESULT_TF));
if (unlikely(ap->excl_link)) {
@@ -885,35 +883,21 @@ static void sil24_qc_prep(struct ata_queued_cmd *qc)
cb = &pp->cmd_block[sil24_tag(qc->tag)];
- switch (qc->tf.protocol) {
- case ATA_PROT_PIO:
- case ATA_PROT_DMA:
- case ATA_PROT_NCQ:
- case ATA_PROT_NODATA:
+ if (!ata_is_atapi(qc->tf.protocol)) {
prb = &cb->ata.prb;
sge = cb->ata.sge;
- break;
-
- case ATA_PROT_ATAPI:
- case ATA_PROT_ATAPI_DMA:
- case ATA_PROT_ATAPI_NODATA:
+ } else {
prb = &cb->atapi.prb;
sge = cb->atapi.sge;
memset(cb->atapi.cdb, 0, 32);
memcpy(cb->atapi.cdb, qc->cdb, qc->dev->cdb_len);
- if (qc->tf.protocol != ATA_PROT_ATAPI_NODATA) {
+ if (ata_is_data(qc->tf.protocol)) {
if (qc->tf.flags & ATA_TFLAG_WRITE)
ctrl = PRB_CTRL_PACKET_WRITE;
else
ctrl = PRB_CTRL_PACKET_READ;
}
- break;
-
- default:
- prb = NULL; /* shut up, gcc */
- sge = NULL;
- BUG();
}
prb->ctrl = cpu_to_le16(ctrl);
diff --git a/drivers/ata/sata_sx4.c b/drivers/ata/sata_sx4.c
index 4d85718..e3d56bc 100644
--- a/drivers/ata/sata_sx4.c
+++ b/drivers/ata/sata_sx4.c
@@ -334,7 +334,7 @@ static inline void pdc20621_ata_sg(struct ata_taskfile *tf, u8 *buf,
{
u32 addr;
unsigned int dw = PDC_DIMM_APKT_PRD >> 2;
- u32 *buf32 = (u32 *) buf;
+ __le32 *buf32 = (__le32 *) buf;
/* output ATA packet S/G table */
addr = PDC_20621_DIMM_BASE + PDC_20621_DIMM_DATA +
@@ -356,7 +356,7 @@ static inline void pdc20621_host_sg(struct ata_taskfile *tf, u8 *buf,
{
u32 addr;
unsigned int dw = PDC_DIMM_HPKT_PRD >> 2;
- u32 *buf32 = (u32 *) buf;
+ __le32 *buf32 = (__le32 *) buf;
/* output Host DMA packet S/G table */
addr = PDC_20621_DIMM_BASE + PDC_20621_DIMM_DATA +
@@ -377,7 +377,7 @@ static inline unsigned int pdc20621_ata_pkt(struct ata_taskfile *tf,
unsigned int portno)
{
unsigned int i, dw;
- u32 *buf32 = (u32 *) buf;
+ __le32 *buf32 = (__le32 *) buf;
u8 dev_reg;
unsigned int dimm_sg = PDC_20621_DIMM_BASE +
@@ -429,7 +429,8 @@ static inline void pdc20621_host_pkt(struct ata_taskfile *tf, u8 *buf,
unsigned int portno)
{
unsigned int dw;
- u32 tmp, *buf32 = (u32 *) buf;
+ u32 tmp;
+ __le32 *buf32 = (__le32 *) buf;
unsigned int host_sg = PDC_20621_DIMM_BASE +
(PDC_DIMM_WINDOW_STEP * portno) +
@@ -473,7 +474,7 @@ static void pdc20621_dma_prep(struct ata_queued_cmd *qc)
void __iomem *mmio = ap->host->iomap[PDC_MMIO_BAR];
void __iomem *dimm_mmio = ap->host->iomap[PDC_DIMM_BAR];
unsigned int portno = ap->port_no;
- unsigned int i, idx, total_len = 0, sgt_len;
+ unsigned int i, si, idx, total_len = 0, sgt_len;
u32 *buf = (u32 *) &pp->dimm_buf[PDC_DIMM_HEADER_SZ];
WARN_ON(!(qc->flags & ATA_QCFLAG_DMAMAP));
@@ -487,7 +488,7 @@ static void pdc20621_dma_prep(struct ata_queued_cmd *qc)
* Build S/G table
*/
idx = 0;
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
buf[idx++] = cpu_to_le32(sg_dma_address(sg));
buf[idx++] = cpu_to_le32(sg_dma_len(sg));
total_len += sg_dma_len(sg);
@@ -700,7 +701,7 @@ static unsigned int pdc20621_qc_issue_prot(struct ata_queued_cmd *qc)
pdc20621_packet_start(qc);
return 0;
- case ATA_PROT_ATAPI_DMA:
+ case ATAPI_PROT_DMA:
BUG();
break;
diff --git a/drivers/scsi/ipr.c b/drivers/scsi/ipr.c
index 0841df0..aa0df0a 100644
--- a/drivers/scsi/ipr.c
+++ b/drivers/scsi/ipr.c
@@ -5142,6 +5142,7 @@ static void ipr_build_ata_ioadl(struct ipr_cmnd *ipr_cmd,
struct ipr_ioadl_desc *last_ioadl = NULL;
int len = qc->nbytes + qc->pad_len;
struct scatterlist *sg;
+ unsigned int si;
if (len == 0)
return;
@@ -5159,7 +5160,7 @@ static void ipr_build_ata_ioadl(struct ipr_cmnd *ipr_cmd,
cpu_to_be32(sizeof(struct ipr_ioadl_desc) * ipr_cmd->dma_use_sg);
}
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
ioadl->flags_and_data_len = cpu_to_be32(ioadl_flags | sg_dma_len(sg));
ioadl->address = cpu_to_be32(sg_dma_address(sg));
@@ -5222,12 +5223,12 @@ static unsigned int ipr_qc_issue(struct ata_queued_cmd *qc)
regs->flags |= IPR_ATA_FLAG_XFER_TYPE_DMA;
break;
- case ATA_PROT_ATAPI:
- case ATA_PROT_ATAPI_NODATA:
+ case ATAPI_PROT_PIO:
+ case ATAPI_PROT_NODATA:
regs->flags |= IPR_ATA_FLAG_PACKET_CMD;
break;
- case ATA_PROT_ATAPI_DMA:
+ case ATAPI_PROT_DMA:
regs->flags |= IPR_ATA_FLAG_PACKET_CMD;
regs->flags |= IPR_ATA_FLAG_XFER_TYPE_DMA;
break;
diff --git a/drivers/scsi/libsas/sas_ata.c b/drivers/scsi/libsas/sas_ata.c
index 0829b55..827cfb1 100644
--- a/drivers/scsi/libsas/sas_ata.c
+++ b/drivers/scsi/libsas/sas_ata.c
@@ -158,8 +158,8 @@ static unsigned int sas_ata_qc_issue(struct ata_queued_cmd *qc)
struct Scsi_Host *host = sas_ha->core.shost;
struct sas_internal *i = to_sas_internal(host->transportt);
struct scatterlist *sg;
- unsigned int num = 0;
unsigned int xfer = 0;
+ unsigned int si;
task = sas_alloc_task(GFP_ATOMIC);
if (!task)
@@ -176,22 +176,20 @@ static unsigned int sas_ata_qc_issue(struct ata_queued_cmd *qc)
ata_tf_to_fis(&qc->tf, 1, 0, (u8*)&task->ata_task.fis);
task->uldd_task = qc;
- if (is_atapi_taskfile(&qc->tf)) {
+ if (ata_is_atapi(qc->tf.protocol)) {
memcpy(task->ata_task.atapi_packet, qc->cdb, qc->dev->cdb_len);
task->total_xfer_len = qc->nbytes + qc->pad_len;
task->num_scatter = qc->pad_len ? qc->n_elem + 1 : qc->n_elem;
} else {
- ata_for_each_sg(sg, qc) {
- num++;
+ for_each_sg(qc->sg, sg, qc->n_elem, si)
xfer += sg->length;
- }
task->total_xfer_len = xfer;
- task->num_scatter = num;
+ task->num_scatter = si;
}
task->data_dir = qc->dma_dir;
- task->scatter = qc->__sg;
+ task->scatter = qc->sg;
task->ata_task.retry_count = 1;
task->task_state_flags = SAS_TASK_STATE_PENDING;
qc->lldd_task = task;
@@ -200,7 +198,7 @@ static unsigned int sas_ata_qc_issue(struct ata_queued_cmd *qc)
case ATA_PROT_NCQ:
task->ata_task.use_ncq = 1;
/* fall through */
- case ATA_PROT_ATAPI_DMA:
+ case ATAPI_PROT_DMA:
case ATA_PROT_DMA:
task->ata_task.dma_xfer = 1;
break;
diff --git a/include/linux/ata.h b/include/linux/ata.h
index e672e80..78bbaca 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -286,9 +286,10 @@ enum {
ATA_CBL_NONE = 0,
ATA_CBL_PATA40 = 1,
ATA_CBL_PATA80 = 2,
- ATA_CBL_PATA40_SHORT = 3, /* 40 wire cable to high UDMA spec */
- ATA_CBL_PATA_UNK = 4,
- ATA_CBL_SATA = 5,
+ ATA_CBL_PATA40_SHORT = 3, /* 40 wire cable to high UDMA spec */
+ ATA_CBL_PATA_UNK = 4, /* don't know, maybe 80c? */
+ ATA_CBL_PATA_IGN = 5, /* don't know, ignore cable handling */
+ ATA_CBL_SATA = 6,
/* SATA Status and Control Registers */
SCR_STATUS = 0,
@@ -324,6 +325,13 @@ enum {
ATA_TFLAG_LBA = (1 << 4), /* enable LBA */
ATA_TFLAG_FUA = (1 << 5), /* enable FUA */
ATA_TFLAG_POLLING = (1 << 6), /* set nIEN to 1 and use polling */
+
+ /* protocol flags */
+ ATA_PROT_FLAG_PIO = (1 << 0), /* is PIO */
+ ATA_PROT_FLAG_DMA = (1 << 1), /* is DMA */
+ ATA_PROT_FLAG_DATA = ATA_PROT_FLAG_PIO | ATA_PROT_FLAG_DMA,
+ ATA_PROT_FLAG_NCQ = (1 << 2), /* is NCQ */
+ ATA_PROT_FLAG_ATAPI = (1 << 3), /* is ATAPI */
};
enum ata_tf_protocols {
@@ -333,9 +341,9 @@ enum ata_tf_protocols {
ATA_PROT_PIO, /* PIO data xfer */
ATA_PROT_DMA, /* DMA */
ATA_PROT_NCQ, /* NCQ */
- ATA_PROT_ATAPI, /* packet command, PIO data xfer*/
- ATA_PROT_ATAPI_NODATA, /* packet command, no data */
- ATA_PROT_ATAPI_DMA, /* packet command with special DMA sauce */
+ ATAPI_PROT_NODATA, /* packet command, no data */
+ ATAPI_PROT_PIO, /* packet command, PIO data xfer*/
+ ATAPI_PROT_DMA, /* packet command with special DMA sauce */
};
enum ata_ioctls {
@@ -346,8 +354,8 @@ enum ata_ioctls {
/* core structures */
struct ata_prd {
- u32 addr;
- u32 flags_len;
+ __le32 addr;
+ __le32 flags_len;
};
struct ata_taskfile {
@@ -373,13 +381,69 @@ struct ata_taskfile {
u8 command; /* IO operation */
};
+/*
+ * protocol tests
+ */
+static inline unsigned int ata_prot_flags(u8 prot)
+{
+ switch (prot) {
+ case ATA_PROT_NODATA:
+ return 0;
+ case ATA_PROT_PIO:
+ return ATA_PROT_FLAG_PIO;
+ case ATA_PROT_DMA:
+ return ATA_PROT_FLAG_DMA;
+ case ATA_PROT_NCQ:
+ return ATA_PROT_FLAG_DMA | ATA_PROT_FLAG_NCQ;
+ case ATAPI_PROT_NODATA:
+ return ATA_PROT_FLAG_ATAPI;
+ case ATAPI_PROT_PIO:
+ return ATA_PROT_FLAG_ATAPI | ATA_PROT_FLAG_PIO;
+ case ATAPI_PROT_DMA:
+ return ATA_PROT_FLAG_ATAPI | ATA_PROT_FLAG_DMA;
+ }
+ return 0;
+}
+
+static inline int ata_is_atapi(u8 prot)
+{
+ return ata_prot_flags(prot) & ATA_PROT_FLAG_ATAPI;
+}
+
+static inline int ata_is_nodata(u8 prot)
+{
+ return !(ata_prot_flags(prot) & ATA_PROT_FLAG_DATA);
+}
+
+static inline int ata_is_pio(u8 prot)
+{
+ return ata_prot_flags(prot) & ATA_PROT_FLAG_PIO;
+}
+
+static inline int ata_is_dma(u8 prot)
+{
+ return ata_prot_flags(prot) & ATA_PROT_FLAG_DMA;
+}
+
+static inline int ata_is_ncq(u8 prot)
+{
+ return ata_prot_flags(prot) & ATA_PROT_FLAG_NCQ;
+}
+
+static inline int ata_is_data(u8 prot)
+{
+ return ata_prot_flags(prot) & ATA_PROT_FLAG_DATA;
+}
+
+/*
+ * id tests
+ */
#define ata_id_is_ata(id) (((id)[0] & (1 << 15)) == 0)
#define ata_id_has_lba(id) ((id)[49] & (1 << 9))
#define ata_id_has_dma(id) ((id)[49] & (1 << 8))
#define ata_id_has_ncq(id) ((id)[76] & (1 << 8))
#define ata_id_queue_depth(id) (((id)[75] & 0x1f) + 1)
#define ata_id_removeable(id) ((id)[0] & (1 << 7))
-#define ata_id_has_dword_io(id) ((id)[48] & (1 << 0))
#define ata_id_has_atapi_AN(id) \
( (((id)[76] != 0x0000) && ((id)[76] != 0xffff)) && \
((id)[78] & (1 << 5)) )
@@ -415,6 +479,7 @@ static inline bool ata_id_has_dipm(const u16 *id)
return val & (1 << 3);
}
+
static inline int ata_id_has_fua(const u16 *id)
{
if ((id[84] & 0xC000) != 0x4000)
@@ -519,6 +584,26 @@ static inline int ata_id_is_sata(const u16 *id)
return ata_id_major_version(id) >= 5 && id[93] == 0;
}
+static inline int ata_id_has_tpm(const u16 *id)
+{
+ /* The TPM bits are only valid on ATA8 */
+ if (ata_id_major_version(id) < 8)
+ return 0;
+ if ((id[48] & 0xC000) != 0x4000)
+ return 0;
+ return id[48] & (1 << 0);
+}
+
+static inline int ata_id_has_dword_io(const u16 *id)
+{
+ /* ATA 8 reuses this flag for "trusted" computing */
+ if (ata_id_major_version(id) > 7)
+ return 0;
+ if (id[48] & (1 << 0))
+ return 1;
+ return 0;
+}
+
static inline int ata_id_current_chs_valid(const u16 *id)
{
/* For ATA-1 devices, if the INITIALIZE DEVICE PARAMETERS command
@@ -574,13 +659,6 @@ static inline int atapi_command_packet_set(const u16 *dev_id)
return (dev_id[0] >> 8) & 0x1f;
}
-static inline int is_atapi_taskfile(const struct ata_taskfile *tf)
-{
- return (tf->protocol == ATA_PROT_ATAPI) ||
- (tf->protocol == ATA_PROT_ATAPI_NODATA) ||
- (tf->protocol == ATA_PROT_ATAPI_DMA);
-}
-
static inline int is_multi_taskfile(struct ata_taskfile *tf)
{
return (tf->command == ATA_CMD_READ_MULTI) ||
diff --git a/include/linux/cdrom.h b/include/linux/cdrom.h
index c6d3e22..fcdc11b 100644
--- a/include/linux/cdrom.h
+++ b/include/linux/cdrom.h
@@ -451,6 +451,7 @@ struct cdrom_generic_command
#define GPCMD_PREVENT_ALLOW_MEDIUM_REMOVAL 0x1e
#define GPCMD_READ_10 0x28
#define GPCMD_READ_12 0xa8
+#define GPCMD_READ_BUFFER 0x3c
#define GPCMD_READ_BUFFER_CAPACITY 0x5c
#define GPCMD_READ_CDVD_CAPACITY 0x25
#define GPCMD_READ_CD 0xbe
@@ -480,7 +481,9 @@ struct cdrom_generic_command
#define GPCMD_TEST_UNIT_READY 0x00
#define GPCMD_VERIFY_10 0x2f
#define GPCMD_WRITE_10 0x2a
+#define GPCMD_WRITE_12 0xaa
#define GPCMD_WRITE_AND_VERIFY_10 0x2e
+#define GPCMD_WRITE_BUFFER 0x3b
/* This is listed as optional in ATAPI 2.6, but is (curiously)
* missing from Mt. Fuji, Table 57. It _is_ mentioned in Mt. Fuji
* Table 377 as an MMC command for SCSi devices though... Most ATAPI
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 124033c..4374c42 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -35,6 +35,7 @@
#include <linux/workqueue.h>
#include <scsi/scsi_host.h>
#include <linux/acpi.h>
+#include <linux/cdrom.h>
/*
* Define if arch has non-standard setup. This is a _PCI_ standard
@@ -143,10 +144,11 @@ enum {
ATA_DFLAG_NCQ_OFF = (1 << 13), /* device limited to non-NCQ mode */
ATA_DFLAG_SPUNDOWN = (1 << 14), /* XXX: for spindown_compat */
ATA_DFLAG_SLEEPING = (1 << 15), /* device is sleeping */
- ATA_DFLAG_INIT_MASK = (1 << 16) - 1,
+ ATA_DFLAG_DUBIOUS_XFER = (1 << 16), /* data transfer not verified */
+ ATA_DFLAG_INIT_MASK = (1 << 24) - 1,
- ATA_DFLAG_DETACH = (1 << 16),
- ATA_DFLAG_DETACHED = (1 << 17),
+ ATA_DFLAG_DETACH = (1 << 24),
+ ATA_DFLAG_DETACHED = (1 << 25),
ATA_DEV_UNKNOWN = 0, /* unknown device */
ATA_DEV_ATA = 1, /* ATA device */
@@ -217,9 +219,7 @@ enum {
/* struct ata_queued_cmd flags */
ATA_QCFLAG_ACTIVE = (1 << 0), /* cmd not yet ack'd to scsi lyer */
- ATA_QCFLAG_SG = (1 << 1), /* have s/g table? */
- ATA_QCFLAG_SINGLE = (1 << 2), /* no s/g, just a single buffer */
- ATA_QCFLAG_DMAMAP = ATA_QCFLAG_SG | ATA_QCFLAG_SINGLE,
+ ATA_QCFLAG_DMAMAP = (1 << 1), /* SG table is DMA mapped */
ATA_QCFLAG_IO = (1 << 3), /* standard IO command */
ATA_QCFLAG_RESULT_TF = (1 << 4), /* result TF requested */
ATA_QCFLAG_CLEAR_EXCL = (1 << 5), /* clear excl_link on completion */
@@ -266,19 +266,15 @@ enum {
PORT_DISABLED = 2,
/* encoding various smaller bitmaps into a single
- * unsigned int bitmap
+ * unsigned long bitmap
*/
- ATA_BITS_PIO = 7,
- ATA_BITS_MWDMA = 5,
- ATA_BITS_UDMA = 8,
+ ATA_NR_PIO_MODES = 7,
+ ATA_NR_MWDMA_MODES = 5,
+ ATA_NR_UDMA_MODES = 8,
ATA_SHIFT_PIO = 0,
- ATA_SHIFT_MWDMA = ATA_SHIFT_PIO + ATA_BITS_PIO,
- ATA_SHIFT_UDMA = ATA_SHIFT_MWDMA + ATA_BITS_MWDMA,
-
- ATA_MASK_PIO = ((1 << ATA_BITS_PIO) - 1) << ATA_SHIFT_PIO,
- ATA_MASK_MWDMA = ((1 << ATA_BITS_MWDMA) - 1) << ATA_SHIFT_MWDMA,
- ATA_MASK_UDMA = ((1 << ATA_BITS_UDMA) - 1) << ATA_SHIFT_UDMA,
+ ATA_SHIFT_MWDMA = ATA_SHIFT_PIO + ATA_NR_PIO_MODES,
+ ATA_SHIFT_UDMA = ATA_SHIFT_MWDMA + ATA_NR_MWDMA_MODES,
/* size of buffer to pad xfers ending on unaligned boundaries */
ATA_DMA_PAD_SZ = 4,
@@ -349,6 +345,21 @@ enum {
ATA_DMA_MASK_ATA = (1 << 0), /* DMA on ATA Disk */
ATA_DMA_MASK_ATAPI = (1 << 1), /* DMA on ATAPI */
ATA_DMA_MASK_CFA = (1 << 2), /* DMA on CF Card */
+
+ /* ATAPI command types */
+ ATAPI_READ = 0, /* READs */
+ ATAPI_WRITE = 1, /* WRITEs */
+ ATAPI_READ_CD = 2, /* READ CD [MSF] */
+ ATAPI_MISC = 3, /* the rest */
+};
+
+enum ata_xfer_mask {
+ ATA_MASK_PIO = ((1LU << ATA_NR_PIO_MODES) - 1)
+ << ATA_SHIFT_PIO,
+ ATA_MASK_MWDMA = ((1LU << ATA_NR_MWDMA_MODES) - 1)
+ << ATA_SHIFT_MWDMA,
+ ATA_MASK_UDMA = ((1LU << ATA_NR_UDMA_MODES) - 1)
+ << ATA_SHIFT_UDMA,
};
enum hsm_task_states {
@@ -447,7 +458,7 @@ struct ata_queued_cmd {
unsigned int tag;
unsigned int n_elem;
unsigned int n_iter;
- unsigned int orig_n_elem;
+ unsigned int mapped_n_elem;
int dma_dir;
@@ -455,17 +466,18 @@ struct ata_queued_cmd {
unsigned int sect_size;
unsigned int nbytes;
+ unsigned int raw_nbytes;
unsigned int curbytes;
struct scatterlist *cursg;
unsigned int cursg_ofs;
+ struct scatterlist *last_sg;
+ struct scatterlist saved_last_sg;
struct scatterlist sgent;
- struct scatterlist pad_sgent;
- void *buf_virt;
+ struct scatterlist extra_sg[2];
- /* DO NOT iterate over __sg manually, use ata_for_each_sg() */
- struct scatterlist *__sg;
+ struct scatterlist *sg;
unsigned int err_mask;
struct ata_taskfile result_tf;
@@ -482,7 +494,7 @@ struct ata_port_stats {
};
struct ata_ering_entry {
- int is_io;
+ unsigned int eflags;
unsigned int err_mask;
u64 timestamp;
};
@@ -522,9 +534,9 @@ struct ata_device {
unsigned int cdb_len;
/* per-dev xfer mask */
- unsigned int pio_mask;
- unsigned int mwdma_mask;
- unsigned int udma_mask;
+ unsigned long pio_mask;
+ unsigned long mwdma_mask;
+ unsigned long udma_mask;
/* for CHS addressing */
u16 cylinders; /* Number of cylinders */
@@ -560,6 +572,8 @@ struct ata_eh_context {
int tries[ATA_MAX_DEVICES];
unsigned int classes[ATA_MAX_DEVICES];
unsigned int did_probe_mask;
+ unsigned int saved_ncq_enabled;
+ u8 saved_xfer_mode[ATA_MAX_DEVICES];
};
struct ata_acpi_drive
@@ -686,7 +700,8 @@ struct ata_port_operations {
void (*bmdma_setup) (struct ata_queued_cmd *qc);
void (*bmdma_start) (struct ata_queued_cmd *qc);
- void (*data_xfer) (struct ata_device *, unsigned char *, unsigned int, int);
+ unsigned int (*data_xfer) (struct ata_device *dev, unsigned char *buf,
+ unsigned int buflen, int rw);
int (*qc_defer) (struct ata_queued_cmd *qc);
void (*qc_prep) (struct ata_queued_cmd *qc);
@@ -832,8 +847,6 @@ extern int ata_busy_sleep(struct ata_port *ap,
unsigned long timeout_pat, unsigned long timeout);
extern void ata_wait_after_reset(struct ata_port *ap, unsigned long deadline);
extern int ata_wait_ready(struct ata_port *ap, unsigned long deadline);
-extern void ata_port_queue_task(struct ata_port *ap, work_func_t fn,
- void *data, unsigned long delay);
extern u32 ata_wait_register(void __iomem *reg, u32 mask, u32 val,
unsigned long interval_msec,
unsigned long timeout_msec);
@@ -848,6 +861,16 @@ extern void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf);
extern void ata_tf_to_fis(const struct ata_taskfile *tf,
u8 pmp, int is_cmd, u8 *fis);
extern void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf);
+extern unsigned long ata_pack_xfermask(unsigned long pio_mask,
+ unsigned long mwdma_mask, unsigned long udma_mask);
+extern void ata_unpack_xfermask(unsigned long xfer_mask,
+ unsigned long *pio_mask, unsigned long *mwdma_mask,
+ unsigned long *udma_mask);
+extern u8 ata_xfer_mask2mode(unsigned long xfer_mask);
+extern unsigned long ata_xfer_mode2mask(u8 xfer_mode);
+extern int ata_xfer_mode2shift(unsigned long xfer_mode);
+extern const char *ata_mode_string(unsigned long xfer_mask);
+extern unsigned long ata_id_xfermask(const u16 *id);
extern void ata_noop_dev_select(struct ata_port *ap, unsigned int device);
extern void ata_std_dev_select(struct ata_port *ap, unsigned int device);
extern u8 ata_check_status(struct ata_port *ap);
@@ -856,17 +879,15 @@ extern void ata_exec_command(struct ata_port *ap, const struct ata_taskfile *tf)
extern int ata_port_start(struct ata_port *ap);
extern int ata_sff_port_start(struct ata_port *ap);
extern irqreturn_t ata_interrupt(int irq, void *dev_instance);
-extern void ata_data_xfer(struct ata_device *adev, unsigned char *buf,
- unsigned int buflen, int write_data);
-extern void ata_data_xfer_noirq(struct ata_device *adev, unsigned char *buf,
- unsigned int buflen, int write_data);
+extern unsigned int ata_data_xfer(struct ata_device *dev,
+ unsigned char *buf, unsigned int buflen, int rw);
+extern unsigned int ata_data_xfer_noirq(struct ata_device *dev,
+ unsigned char *buf, unsigned int buflen, int rw);
extern int ata_std_qc_defer(struct ata_queued_cmd *qc);
extern void ata_dumb_qc_prep(struct ata_queued_cmd *qc);
extern void ata_qc_prep(struct ata_queued_cmd *qc);
extern void ata_noop_qc_prep(struct ata_queued_cmd *qc);
extern unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc);
-extern void ata_sg_init_one(struct ata_queued_cmd *qc, void *buf,
- unsigned int buflen);
extern void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
unsigned int n_elem);
extern unsigned int ata_dev_classify(const struct ata_taskfile *tf);
@@ -875,7 +896,6 @@ extern void ata_id_string(const u16 *id, unsigned char *s,
unsigned int ofs, unsigned int len);
extern void ata_id_c_string(const u16 *id, unsigned char *s,
unsigned int ofs, unsigned int len);
-extern void ata_id_to_dma_mode(struct ata_device *dev, u8 unknown);
extern void ata_bmdma_setup(struct ata_queued_cmd *qc);
extern void ata_bmdma_start(struct ata_queued_cmd *qc);
extern void ata_bmdma_stop(struct ata_queued_cmd *qc);
@@ -910,6 +930,7 @@ extern u8 ata_irq_on(struct ata_port *ap);
extern int ata_cable_40wire(struct ata_port *ap);
extern int ata_cable_80wire(struct ata_port *ap);
extern int ata_cable_sata(struct ata_port *ap);
+extern int ata_cable_ignore(struct ata_port *ap);
extern int ata_cable_unknown(struct ata_port *ap);
/*
@@ -917,11 +938,13 @@ extern int ata_cable_unknown(struct ata_port *ap);
*/
extern unsigned int ata_pio_need_iordy(const struct ata_device *);
+extern const struct ata_timing *ata_timing_find_mode(u8 xfer_mode);
extern int ata_timing_compute(struct ata_device *, unsigned short,
struct ata_timing *, int, int);
extern void ata_timing_merge(const struct ata_timing *,
const struct ata_timing *, struct ata_timing *,
unsigned int);
+extern u8 ata_timing_cycle2mode(unsigned int xfer_shift, int cycle);
enum {
ATA_TIMING_SETUP = (1 << 0),
@@ -948,15 +971,40 @@ static inline const struct ata_acpi_gtm *ata_acpi_init_gtm(struct ata_port *ap)
return &ap->__acpi_init_gtm;
return NULL;
}
-extern int ata_acpi_cbl_80wire(struct ata_port *ap);
int ata_acpi_stm(struct ata_port *ap, const struct ata_acpi_gtm *stm);
int ata_acpi_gtm(struct ata_port *ap, struct ata_acpi_gtm *stm);
+unsigned long ata_acpi_gtm_xfermask(struct ata_device *dev,
+ const struct ata_acpi_gtm *gtm);
+int ata_acpi_cbl_80wire(struct ata_port *ap, const struct ata_acpi_gtm *gtm);
#else
static inline const struct ata_acpi_gtm *ata_acpi_init_gtm(struct ata_port *ap)
{
return NULL;
}
-static inline int ata_acpi_cbl_80wire(struct ata_port *ap) { return 0; }
+
+static inline int ata_acpi_stm(const struct ata_port *ap,
+ struct ata_acpi_gtm *stm)
+{
+ return -ENOSYS;
+}
+
+static inline int ata_acpi_gtm(const struct ata_port *ap,
+ struct ata_acpi_gtm *stm)
+{
+ return -ENOSYS;
+}
+
+static inline unsigned int ata_acpi_gtm_xfermask(struct ata_device *dev,
+ const struct ata_acpi_gtm *gtm)
+{
+ return 0;
+}
+
+static inline int ata_acpi_cbl_80wire(struct ata_port *ap,
+ const struct ata_acpi_gtm *gtm)
+{
+ return 0;
+}
#endif
#ifdef CONFIG_PCI
@@ -985,8 +1033,12 @@ extern int ata_pci_init_bmdma(struct ata_host *host);
extern int ata_pci_prepare_sff_host(struct pci_dev *pdev,
const struct ata_port_info * const * ppi,
struct ata_host **r_host);
+extern int ata_pci_activate_sff_host(struct ata_host *host,
+ irq_handler_t irq_handler,
+ struct scsi_host_template *sht);
extern int pci_test_config_bits(struct pci_dev *pdev, const struct pci_bits *bits);
-extern unsigned long ata_pci_default_filter(struct ata_device *, unsigned long);
+extern unsigned long ata_pci_default_filter(struct ata_device *dev,
+ unsigned long xfer_mask);
#endif /* CONFIG_PCI */
/*
@@ -1074,35 +1126,6 @@ extern void ata_port_pbar_desc(struct ata_port *ap, int bar, ssize_t offset,
const char *name);
#endif
-/*
- * qc helpers
- */
-static inline struct scatterlist *
-ata_qc_first_sg(struct ata_queued_cmd *qc)
-{
- qc->n_iter = 0;
- if (qc->n_elem)
- return qc->__sg;
- if (qc->pad_len)
- return &qc->pad_sgent;
- return NULL;
-}
-
-static inline struct scatterlist *
-ata_qc_next_sg(struct scatterlist *sg, struct ata_queued_cmd *qc)
-{
- if (sg == &qc->pad_sgent)
- return NULL;
- if (++qc->n_iter < qc->n_elem)
- return sg_next(sg);
- if (qc->pad_len)
- return &qc->pad_sgent;
- return NULL;
-}
-
-#define ata_for_each_sg(sg, qc) \
- for (sg = ata_qc_first_sg(qc); sg; sg = ata_qc_next_sg(sg, qc))
-
static inline unsigned int ata_tag_valid(unsigned int tag)
{
return (tag < ATA_MAX_QUEUE) ? 1 : 0;
@@ -1337,15 +1360,17 @@ static inline void ata_tf_init(struct ata_device *dev, struct ata_taskfile *tf)
static inline void ata_qc_reinit(struct ata_queued_cmd *qc)
{
qc->dma_dir = DMA_NONE;
- qc->__sg = NULL;
+ qc->sg = NULL;
qc->flags = 0;
qc->cursg = NULL;
qc->cursg_ofs = 0;
- qc->nbytes = qc->curbytes = 0;
+ qc->nbytes = qc->raw_nbytes = qc->curbytes = 0;
qc->n_elem = 0;
+ qc->mapped_n_elem = 0;
qc->n_iter = 0;
qc->err_mask = 0;
qc->pad_len = 0;
+ qc->last_sg = NULL;
qc->sect_size = ATA_SECT_SIZE;
ata_tf_init(qc->dev, &qc->tf);
@@ -1362,6 +1387,27 @@ static inline int ata_try_flush_cache(const struct ata_device *dev)
ata_id_has_flush_ext(dev->id);
}
+static inline int atapi_cmd_type(u8 opcode)
+{
+ switch (opcode) {
+ case GPCMD_READ_10:
+ case GPCMD_READ_12:
+ return ATAPI_READ;
+
+ case GPCMD_WRITE_10:
+ case GPCMD_WRITE_12:
+ case GPCMD_WRITE_AND_VERIFY_10:
+ return ATAPI_WRITE;
+
+ case GPCMD_READ_CD:
+ case GPCMD_READ_CD_MSF:
+ return ATAPI_READ_CD;
+
+ default:
+ return ATAPI_MISC;
+ }
+}
+
static inline unsigned int ac_err_mask(u8 status)
{
if (status & (ATA_BUSY | ATA_DRQ))
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 7f22151..1fbd025 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -2066,6 +2066,9 @@
#define PCI_VENDOR_ID_NETCELL 0x169c
#define PCI_DEVICE_ID_REVOLUTION 0x0044
+#define PCI_VENDOR_ID_CENATEK 0x16CA
+#define PCI_DEVICE_ID_CENATEK_IDE 0x0001
+
#define PCI_VENDOR_ID_VITESSE 0x1725
#define PCI_DEVICE_ID_VITESSE_VSC7174 0x7174
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2007-10-25 7:49 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2007-10-25 7:49 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
A couple small cleanups, the rest fixes.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/ahci.c | 144 +++++++++++++++++++++++++++++++++++++++++++++
drivers/ata/libata-core.c | 40 ++++++------
drivers/ata/libata-eh.c | 12 ++--
drivers/ata/pata_icside.c | 42 +++++++------
drivers/ata/sata_nv.c | 6 +-
5 files changed, 195 insertions(+), 49 deletions(-)
Adrian Bunk (1):
libata-core.c: make 2 functions static
Al Viro (1):
Fix pata_icside build for recent libata API changes
Alan Cox (1):
libata-core: Be a bit more relaxed about early DMA zero devices
Jeff Garzik (1):
[libata] Create [and use -ed.] internal helper ata_dev_set_feature()
Kuan Luo (1):
[libata] sata_nv: SWNCQ should not apply to MCP61
Tejun Heo (2):
libata: cosmetic clean up in ata_eh_reset()
ahci: ahci: implement workaround for ASUS P5W-DH Deluxe ahci_broken_hardreset(), take #2
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 95229e7..49cf4cf 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -41,6 +41,7 @@
#include <linux/interrupt.h>
#include <linux/dma-mapping.h>
#include <linux/device.h>
+#include <linux/dmi.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_cmnd.h>
#include <linux/libata.h>
@@ -241,6 +242,7 @@ static void ahci_pmp_attach(struct ata_port *ap);
static void ahci_pmp_detach(struct ata_port *ap);
static void ahci_error_handler(struct ata_port *ap);
static void ahci_vt8251_error_handler(struct ata_port *ap);
+static void ahci_p5wdh_error_handler(struct ata_port *ap);
static void ahci_post_internal_cmd(struct ata_queued_cmd *qc);
static int ahci_port_resume(struct ata_port *ap);
static unsigned int ahci_fill_sg(struct ata_queued_cmd *qc, void *cmd_tbl);
@@ -339,6 +341,40 @@ static const struct ata_port_operations ahci_vt8251_ops = {
.port_stop = ahci_port_stop,
};
+static const struct ata_port_operations ahci_p5wdh_ops = {
+ .check_status = ahci_check_status,
+ .check_altstatus = ahci_check_status,
+ .dev_select = ata_noop_dev_select,
+
+ .tf_read = ahci_tf_read,
+
+ .qc_defer = sata_pmp_qc_defer_cmd_switch,
+ .qc_prep = ahci_qc_prep,
+ .qc_issue = ahci_qc_issue,
+
+ .irq_clear = ahci_irq_clear,
+
+ .scr_read = ahci_scr_read,
+ .scr_write = ahci_scr_write,
+
+ .freeze = ahci_freeze,
+ .thaw = ahci_thaw,
+
+ .error_handler = ahci_p5wdh_error_handler,
+ .post_internal_cmd = ahci_post_internal_cmd,
+
+ .pmp_attach = ahci_pmp_attach,
+ .pmp_detach = ahci_pmp_detach,
+
+#ifdef CONFIG_PM
+ .port_suspend = ahci_port_suspend,
+ .port_resume = ahci_port_resume,
+#endif
+
+ .port_start = ahci_port_start,
+ .port_stop = ahci_port_stop,
+};
+
#define AHCI_HFLAGS(flags) .private_data = (void *)(flags)
static const struct ata_port_info ahci_port_info[] = {
@@ -1213,6 +1249,53 @@ static int ahci_vt8251_hardreset(struct ata_link *link, unsigned int *class,
return rc ?: -EAGAIN;
}
+static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
+{
+ struct ata_port *ap = link->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+ u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
+ struct ata_taskfile tf;
+ int rc;
+
+ ahci_stop_engine(ap);
+
+ /* clear D2H reception area to properly wait for D2H FIS */
+ ata_tf_init(link->device, &tf);
+ tf.command = 0x80;
+ ata_tf_to_fis(&tf, 0, 0, d2h_fis);
+
+ rc = sata_link_hardreset(link, sata_ehc_deb_timing(&link->eh_context),
+ deadline);
+
+ ahci_start_engine(ap);
+
+ if (rc || ata_link_offline(link))
+ return rc;
+
+ /* spec mandates ">= 2ms" before checking status */
+ msleep(150);
+
+ /* The pseudo configuration device on SIMG4726 attached to
+ * ASUS P5W-DH Deluxe doesn't send signature FIS after
+ * hardreset if no device is attached to the first downstream
+ * port && the pseudo device locks up on SRST w/ PMP==0. To
+ * work around this, wait for !BSY only briefly. If BSY isn't
+ * cleared, perform CLO and proceed to IDENTIFY (achieved by
+ * ATA_LFLAG_NO_SRST and ATA_LFLAG_ASSUME_ATA).
+ *
+ * Wait for two seconds. Devices attached to downstream port
+ * which can't process the following IDENTIFY after this will
+ * have to be reset again. For most cases, this should
+ * suffice while making probing snappish enough.
+ */
+ rc = ata_wait_ready(ap, jiffies + 2 * HZ);
+ if (rc)
+ ahci_kick_engine(ap, 0);
+
+ return 0;
+}
+
static void ahci_postreset(struct ata_link *link, unsigned int *class)
{
struct ata_port *ap = link->ap;
@@ -1670,6 +1753,19 @@ static void ahci_vt8251_error_handler(struct ata_port *ap)
ahci_postreset);
}
+static void ahci_p5wdh_error_handler(struct ata_port *ap)
+{
+ if (!(ap->pflags & ATA_PFLAG_FROZEN)) {
+ /* restart engine */
+ ahci_stop_engine(ap);
+ ahci_start_engine(ap);
+ }
+
+ /* perform recovery */
+ ata_do_eh(ap, ata_std_prereset, ahci_softreset, ahci_p5wdh_hardreset,
+ ahci_postreset);
+}
+
static void ahci_post_internal_cmd(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
@@ -1955,6 +2051,51 @@ static void ahci_print_info(struct ata_host *host)
);
}
+/* On ASUS P5W DH Deluxe, the second port of PCI device 00:1f.2 is
+ * hardwired to on-board SIMG 4726. The chipset is ICH8 and doesn't
+ * support PMP and the 4726 either directly exports the device
+ * attached to the first downstream port or acts as a hardware storage
+ * controller and emulate a single ATA device (can be RAID 0/1 or some
+ * other configuration).
+ *
+ * When there's no device attached to the first downstream port of the
+ * 4726, "Config Disk" appears, which is a pseudo ATA device to
+ * configure the 4726. However, ATA emulation of the device is very
+ * lame. It doesn't send signature D2H Reg FIS after the initial
+ * hardreset, pukes on SRST w/ PMP==0 and has bunch of other issues.
+ *
+ * The following function works around the problem by always using
+ * hardreset on the port and not depending on receiving signature FIS
+ * afterward. If signature FIS isn't received soon, ATA class is
+ * assumed without follow-up softreset.
+ */
+static void ahci_p5wdh_workaround(struct ata_host *host)
+{
+ static struct dmi_system_id sysids[] = {
+ {
+ .ident = "P5W DH Deluxe",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR,
+ "ASUSTEK COMPUTER INC"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "P5W DH Deluxe"),
+ },
+ },
+ { }
+ };
+ struct pci_dev *pdev = to_pci_dev(host->dev);
+
+ if (pdev->bus->number == 0 && pdev->devfn == PCI_DEVFN(0x1f, 2) &&
+ dmi_check_system(sysids)) {
+ struct ata_port *ap = host->ports[1];
+
+ dev_printk(KERN_INFO, &pdev->dev, "enabling ASUS P5W DH "
+ "Deluxe on-board SIMG4726 workaround\n");
+
+ ap->ops = &ahci_p5wdh_ops;
+ ap->link.flags |= ATA_LFLAG_NO_SRST | ATA_LFLAG_ASSUME_ATA;
+ }
+}
+
static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
@@ -2024,6 +2165,9 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
ap->ops = &ata_dummy_port_ops;
}
+ /* apply workaround for ASUS P5W DH Deluxe mainboard */
+ ahci_p5wdh_workaround(host);
+
/* initialize adapter */
rc = ahci_configure_dma_masks(pdev, hpriv->cap & HOST_CAP_64);
if (rc)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 2d147b5..9d10e2f 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -68,7 +68,8 @@ const unsigned long sata_deb_timing_long[] = { 100, 2000, 5000 };
static unsigned int ata_dev_init_params(struct ata_device *dev,
u16 heads, u16 sectors);
static unsigned int ata_dev_set_xfermode(struct ata_device *dev);
-static unsigned int ata_dev_set_AN(struct ata_device *dev, u8 enable);
+static unsigned int ata_dev_set_feature(struct ata_device *dev,
+ u8 enable, u8 feature);
static void ata_dev_xfermask(struct ata_device *dev);
static unsigned long ata_dev_blacklisted(const struct ata_device *dev);
@@ -1799,13 +1800,7 @@ int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class,
* SET_FEATURES spin-up subcommand before it will accept
* anything other than the original IDENTIFY command.
*/
- ata_tf_init(dev, &tf);
- tf.command = ATA_CMD_SET_FEATURES;
- tf.feature = SETFEATURES_SPINUP;
- tf.protocol = ATA_PROT_NODATA;
- tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE;
- err_mask = ata_exec_internal(dev, &tf, NULL,
- DMA_NONE, NULL, 0, 0);
+ err_mask = ata_dev_set_feature(dev, SETFEATURES_SPINUP, 0);
if (err_mask && id[2] != 0x738c) {
rc = -EIO;
reason = "SPINUP failed";
@@ -2075,7 +2070,8 @@ int ata_dev_configure(struct ata_device *dev)
unsigned int err_mask;
/* issue SET feature command to turn this on */
- err_mask = ata_dev_set_AN(dev, SETFEATURES_SATA_ENABLE);
+ err_mask = ata_dev_set_feature(dev,
+ SETFEATURES_SATA_ENABLE, SATA_AN);
if (err_mask)
ata_dev_printk(dev, KERN_ERR,
"failed to enable ATAPI AN "
@@ -2886,6 +2882,13 @@ static int ata_dev_set_mode(struct ata_device *dev)
dev->pio_mode <= XFER_PIO_2)
err_mask &= ~AC_ERR_DEV;
+ /* Early MWDMA devices do DMA but don't allow DMA mode setting.
+ Don't fail an MWDMA0 set IFF the device indicates it is in MWDMA0 */
+ if (dev->xfer_shift == ATA_SHIFT_MWDMA &&
+ dev->dma_mode == XFER_MW_DMA_0 &&
+ (dev->id[63] >> 8) & 1)
+ err_mask &= ~AC_ERR_DEV;
+
if (err_mask) {
ata_dev_printk(dev, KERN_ERR, "failed to set xfermode "
"(err_mask=0x%x)\n", err_mask);
@@ -3947,9 +3950,6 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
{ "_NEC DV5800A", NULL, ATA_HORKAGE_NODMA },
{ "SAMSUNG CD-ROM SN-124", "N001", ATA_HORKAGE_NODMA },
{ "Seagate STT20000A", NULL, ATA_HORKAGE_NODMA },
- { "IOMEGA ZIP 250 ATAPI", NULL, ATA_HORKAGE_NODMA }, /* temporary fix */
- { "IOMEGA ZIP 250 ATAPI Floppy",
- NULL, ATA_HORKAGE_NODMA },
/* Odd clown on sil3726/4726 PMPs */
{ "Config Disk", NULL, ATA_HORKAGE_NODMA |
ATA_HORKAGE_SKIP_PM },
@@ -4007,7 +4007,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
{ }
};
-int strn_pattern_cmp(const char *patt, const char *name, int wildchar)
+static int strn_pattern_cmp(const char *patt, const char *name, int wildchar)
{
const char *p;
int len;
@@ -4181,15 +4181,14 @@ static unsigned int ata_dev_set_xfermode(struct ata_device *dev)
DPRINTK("EXIT, err_mask=%x\n", err_mask);
return err_mask;
}
-
/**
- * ata_dev_set_AN - Issue SET FEATURES - SATA FEATURES
+ * ata_dev_set_feature - Issue SET FEATURES - SATA FEATURES
* @dev: Device to which command will be sent
* @enable: Whether to enable or disable the feature
+ * @feature: The sector count represents the feature to set
*
* Issue SET FEATURES - SATA FEATURES command to device @dev
- * on port @ap with sector count set to indicate Asynchronous
- * Notification feature
+ * on port @ap with sector count
*
* LOCKING:
* PCI/etc. bus probe sem.
@@ -4197,7 +4196,8 @@ static unsigned int ata_dev_set_xfermode(struct ata_device *dev)
* RETURNS:
* 0 on success, AC_ERR_* mask otherwise.
*/
-static unsigned int ata_dev_set_AN(struct ata_device *dev, u8 enable)
+static unsigned int ata_dev_set_feature(struct ata_device *dev, u8 enable,
+ u8 feature)
{
struct ata_taskfile tf;
unsigned int err_mask;
@@ -4210,7 +4210,7 @@ static unsigned int ata_dev_set_AN(struct ata_device *dev, u8 enable)
tf.feature = enable;
tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE;
tf.protocol = ATA_PROT_NODATA;
- tf.nsect = SATA_AN;
+ tf.nsect = feature;
err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
@@ -6921,7 +6921,7 @@ int ata_host_activate(struct ata_host *host, int irq,
* LOCKING:
* Kernel thread context (may sleep).
*/
-void ata_port_detach(struct ata_port *ap)
+static void ata_port_detach(struct ata_port *ap)
{
unsigned long flags;
struct ata_link *link;
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 93e2b54..8cb35bb 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -2071,7 +2071,7 @@ int ata_eh_reset(struct ata_link *link, int classify,
int try = 0;
struct ata_device *dev;
unsigned long deadline;
- unsigned int action;
+ unsigned int tmp_action;
ata_reset_fn_t reset;
unsigned long flags;
int rc;
@@ -2086,14 +2086,14 @@ int ata_eh_reset(struct ata_link *link, int classify,
/* Determine which reset to use and record in ehc->i.action.
* prereset() may examine and modify it.
*/
- action = ehc->i.action;
- ehc->i.action &= ~ATA_EH_RESET_MASK;
if (softreset && (!hardreset || (!(link->flags & ATA_LFLAG_NO_SRST) &&
!sata_set_spd_needed(link) &&
- !(action & ATA_EH_HARDRESET))))
- ehc->i.action |= ATA_EH_SOFTRESET;
+ !(ehc->i.action & ATA_EH_HARDRESET))))
+ tmp_action = ATA_EH_SOFTRESET;
else
- ehc->i.action |= ATA_EH_HARDRESET;
+ tmp_action = ATA_EH_HARDRESET;
+
+ ehc->i.action = (ehc->i.action & ~ATA_EH_RESET_MASK) | tmp_action;
if (prereset) {
rc = prereset(link, jiffies + ATA_EH_PRERESET_TIMEOUT);
diff --git a/drivers/ata/pata_icside.c b/drivers/ata/pata_icside.c
index be30923..842fe08 100644
--- a/drivers/ata/pata_icside.c
+++ b/drivers/ata/pata_icside.c
@@ -332,12 +332,13 @@ static void ata_dummy_noret(struct ata_port *port)
{
}
-static void pata_icside_postreset(struct ata_port *ap, unsigned int *classes)
+static void pata_icside_postreset(struct ata_link *link, unsigned int *classes)
{
+ struct ata_port *ap = link->ap;
struct pata_icside_state *state = ap->host->private_data;
if (classes[0] != ATA_DEV_NONE || classes[1] != ATA_DEV_NONE)
- return ata_std_postreset(ap, classes);
+ return ata_std_postreset(link, classes);
state->port[ap->port_no].disabled = 1;
@@ -395,29 +396,30 @@ static struct ata_port_operations pata_icside_port_ops = {
static void __devinit
pata_icside_setup_ioaddr(struct ata_port *ap, void __iomem *base,
- const struct portinfo *info)
+ struct pata_icside_info *info,
+ const struct portinfo *port)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
- void __iomem *cmd = base + info->dataoffset;
+ void __iomem *cmd = base + port->dataoffset;
ioaddr->cmd_addr = cmd;
- ioaddr->data_addr = cmd + (ATA_REG_DATA << info->stepping);
- ioaddr->error_addr = cmd + (ATA_REG_ERR << info->stepping);
- ioaddr->feature_addr = cmd + (ATA_REG_FEATURE << info->stepping);
- ioaddr->nsect_addr = cmd + (ATA_REG_NSECT << info->stepping);
- ioaddr->lbal_addr = cmd + (ATA_REG_LBAL << info->stepping);
- ioaddr->lbam_addr = cmd + (ATA_REG_LBAM << info->stepping);
- ioaddr->lbah_addr = cmd + (ATA_REG_LBAH << info->stepping);
- ioaddr->device_addr = cmd + (ATA_REG_DEVICE << info->stepping);
- ioaddr->status_addr = cmd + (ATA_REG_STATUS << info->stepping);
- ioaddr->command_addr = cmd + (ATA_REG_CMD << info->stepping);
-
- ioaddr->ctl_addr = base + info->ctrloffset;
+ ioaddr->data_addr = cmd + (ATA_REG_DATA << port->stepping);
+ ioaddr->error_addr = cmd + (ATA_REG_ERR << port->stepping);
+ ioaddr->feature_addr = cmd + (ATA_REG_FEATURE << port->stepping);
+ ioaddr->nsect_addr = cmd + (ATA_REG_NSECT << port->stepping);
+ ioaddr->lbal_addr = cmd + (ATA_REG_LBAL << port->stepping);
+ ioaddr->lbam_addr = cmd + (ATA_REG_LBAM << port->stepping);
+ ioaddr->lbah_addr = cmd + (ATA_REG_LBAH << port->stepping);
+ ioaddr->device_addr = cmd + (ATA_REG_DEVICE << port->stepping);
+ ioaddr->status_addr = cmd + (ATA_REG_STATUS << port->stepping);
+ ioaddr->command_addr = cmd + (ATA_REG_CMD << port->stepping);
+
+ ioaddr->ctl_addr = base + port->ctrloffset;
ioaddr->altstatus_addr = ioaddr->ctl_addr;
ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx",
- info->raw_base + info->dataoffset,
- info->raw_base + info->ctrloffset);
+ info->raw_base + port->dataoffset,
+ info->raw_base + port->ctrloffset);
if (info->raw_ioc_base)
ata_port_desc(ap, "iocbase 0x%lx", info->raw_ioc_base);
@@ -441,7 +443,7 @@ static int __devinit pata_icside_register_v5(struct pata_icside_info *info)
info->nr_ports = 1;
info->port[0] = &pata_icside_portinfo_v5;
- info->raw_base = ecard_resource_start(ec, ECARD_RES_MEMC);
+ info->raw_base = ecard_resource_start(info->ec, ECARD_RES_MEMC);
return 0;
}
@@ -522,7 +524,7 @@ static int __devinit pata_icside_add_ports(struct pata_icside_info *info)
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->ops = &pata_icside_port_ops;
- pata_icside_setup_ioaddr(ap, info->base, info->port[i]);
+ pata_icside_setup_ioaddr(ap, info->base, info, info->port[i]);
}
return ata_host_activate(host, ec->irq, ata_interrupt, 0,
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 2e0279f..f1b422f 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -365,9 +365,9 @@ static const struct pci_device_id nv_pci_tbl[] = {
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2), SWNCQ },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA), SWNCQ },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA2), SWNCQ },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA), SWNCQ },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA2), SWNCQ },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA3), SWNCQ },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA), GENERIC },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA2), GENERIC },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA3), GENERIC },
{ } /* terminate list */
};
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2007-10-15 20:20 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2007-10-15 20:20 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
The sata_nv update has been in -mm for a while, but couldn't make the
last drop due to last minute bugs.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/Kconfig | 9 +
drivers/ata/Makefile | 1 +
drivers/ata/ata_piix.c | 35 ++-
drivers/ata/libata-core.c | 9 +-
drivers/ata/libata-scsi.c | 5 +-
drivers/ata/pata_cs5536.c | 346 ++++++++++++++++++
drivers/ata/pata_pcmcia.c | 2 +
drivers/ata/pata_sil680.c | 61 +++-
drivers/ata/sata_nv.c | 851 ++++++++++++++++++++++++++++++++++++++++++++-
9 files changed, 1298 insertions(+), 21 deletions(-)
create mode 100644 drivers/ata/pata_cs5536.c
Andrew Paprocki (1):
libata: prevent devices with blank model names from being DMA blacklisted
Benjamin Herrenschmidt (1):
[libata] pata_sil680: Add MMIO support
Jason Gaston (1):
ata_piix: SATA 2port controller port map fix
Kristoffer Ericson (1):
[libata] pata_pcmcia: Add additional id string (corsair, 1GB)
Kuan Luo (1):
[libata] sata_nv: add SW NCQ support for MCP51/MCP55/MCP61
Martin K. Petersen (1):
pata_cs5536: ATA driver for Geode companion chip
Tejun Heo (2):
libata: fix revalidation issuing after configuration commands
libata: add ST9160821AS / 3.CCD to NCQ blacklist
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 4672066..33f5eb0 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -272,6 +272,15 @@ config PATA_CS5535
If unsure, say N.
+config PATA_CS5536
+ tristate "CS5536 PATA support (Experimental)"
+ depends on PCI && X86 && !X86_64 && EXPERIMENTAL
+ help
+ This option enables support for the AMD CS5536
+ companion chip used with the Geode LX processor family.
+
+ If unsure, say N.
+
config PATA_CYPRESS
tristate "Cypress CY82C693 PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 2a63645..6bdc307 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_PATA_CMD64X) += pata_cmd64x.o
obj-$(CONFIG_PATA_CS5520) += pata_cs5520.o
obj-$(CONFIG_PATA_CS5530) += pata_cs5530.o
obj-$(CONFIG_PATA_CS5535) += pata_cs5535.o
+obj-$(CONFIG_PATA_CS5536) += pata_cs5536.o
obj-$(CONFIG_PATA_CYPRESS) += pata_cypress.o
obj-$(CONFIG_PATA_EFAR) += pata_efar.o
obj-$(CONFIG_PATA_HPT366) += pata_hpt366.o
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 9ce4aa9..3c6f43e 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -130,6 +130,7 @@ enum {
ich8_sata_ahci = 9,
piix_pata_mwdma = 10, /* PIIX3 MWDMA only */
tolapai_sata_ahci = 11,
+ ich9_2port_sata = 12,
/* constants for mapping table */
P0 = 0, /* port 0 */
@@ -238,19 +239,19 @@ static const struct pci_device_id piix_pci_tbl[] = {
/* SATA Controller 1 IDE (ICH8) */
{ 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
/* SATA Controller 2 IDE (ICH8) */
- { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
/* Mobile SATA Controller IDE (ICH8M) */
{ 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
/* SATA Controller IDE (ICH9) */
{ 0x8086, 0x2920, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
/* SATA Controller IDE (ICH9) */
- { 0x8086, 0x2921, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ { 0x8086, 0x2921, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
/* SATA Controller IDE (ICH9) */
- { 0x8086, 0x2926, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ { 0x8086, 0x2926, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
/* SATA Controller IDE (ICH9M) */
- { 0x8086, 0x2928, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ { 0x8086, 0x2928, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
/* SATA Controller IDE (ICH9M) */
- { 0x8086, 0x292d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ { 0x8086, 0x292d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
/* SATA Controller IDE (ICH9M) */
{ 0x8086, 0x292e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
/* SATA Controller IDE (Tolapai) */
@@ -448,6 +449,18 @@ static const struct piix_map_db tolapai_map_db = {
},
};
+static const struct piix_map_db ich9_2port_map_db = {
+ .mask = 0x3,
+ .port_enable = 0x3,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, NA, P1, NA }, /* 00b */
+ { RV, RV, RV, RV }, /* 01b */
+ { RV, RV, RV, RV }, /* 10b */
+ { RV, RV, RV, RV },
+ },
+};
+
static const struct piix_map_db *piix_map_db_table[] = {
[ich5_sata] = &ich5_map_db,
[ich6_sata] = &ich6_map_db,
@@ -455,6 +468,7 @@ static const struct piix_map_db *piix_map_db_table[] = {
[ich6m_sata_ahci] = &ich6m_map_db,
[ich8_sata_ahci] = &ich8_map_db,
[tolapai_sata_ahci] = &tolapai_map_db,
+ [ich9_2port_sata] = &ich9_2port_map_db,
};
static struct ata_port_info piix_port_info[] = {
@@ -570,6 +584,17 @@ static struct ata_port_info piix_port_info[] = {
.udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
+
+ [ich9_2port_sata] =
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &piix_sata_ops,
+ },
};
static struct pci_bits piix_enable_bits[] = {
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index b05384a..68699b3 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3984,6 +3984,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
{ "ST9120822AS", "3.CLF", ATA_HORKAGE_NONCQ, },
{ "ST9160821AS", "3.CLF", ATA_HORKAGE_NONCQ, },
{ "ST9160821AS", "3.ALD", ATA_HORKAGE_NONCQ, },
+ { "ST9160821AS", "3.CCD", ATA_HORKAGE_NONCQ, },
{ "ST3160812AS", "3.ADJ", ATA_HORKAGE_NONCQ, },
{ "ST980813AS", "3.ADB", ATA_HORKAGE_NONCQ, },
{ "SAMSUNG HD401LJ", "ZZ100-15", ATA_HORKAGE_NONCQ, },
@@ -4013,8 +4014,14 @@ int strn_pattern_cmp(const char *patt, const char *name, int wildchar)
p = strchr(patt, wildchar);
if (p && ((*(p + 1)) == 0))
len = p - patt;
- else
+ else {
len = strlen(name);
+ if (!len) {
+ if (!*patt)
+ return 0;
+ return -1;
+ }
+ }
return strncmp(patt, name, len);
}
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index ea53e6a..d63c81e 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -1363,6 +1363,7 @@ nothing_to_do:
static void ata_scsi_qc_complete(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
+ struct ata_eh_info *ehi = &qc->dev->link->eh_info;
struct scsi_cmnd *cmd = qc->scsicmd;
u8 *cdb = cmd->cmnd;
int need_sense = (qc->err_mask != 0);
@@ -1376,14 +1377,14 @@ static void ata_scsi_qc_complete(struct ata_queued_cmd *qc)
case ATA_CMD_SET_FEATURES:
if ((qc->tf.feature == SETFEATURES_WC_ON) ||
(qc->tf.feature == SETFEATURES_WC_OFF)) {
- ap->link.eh_info.action |= ATA_EH_REVALIDATE;
+ ehi->action |= ATA_EH_REVALIDATE;
ata_port_schedule_eh(ap);
}
break;
case ATA_CMD_INIT_DEV_PARAMS: /* CHS translation changed */
case ATA_CMD_SET_MULTI: /* multi_count changed */
- ap->link.eh_info.action |= ATA_EH_REVALIDATE;
+ ehi->action |= ATA_EH_REVALIDATE;
ata_port_schedule_eh(ap);
break;
}
diff --git a/drivers/ata/pata_cs5536.c b/drivers/ata/pata_cs5536.c
new file mode 100644
index 0000000..21405bf
--- /dev/null
+++ b/drivers/ata/pata_cs5536.c
@@ -0,0 +1,346 @@
+/*
+ * pata_cs5536.c - CS5536 PATA for new ATA layer
+ * (C) 2007 Martin K. Petersen <mkp@mkp.net>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * Documentation:
+ * Available from AMD web site.
+ *
+ * The IDE timing registers for the CS5536 live in the Geode Machine
+ * Specific Register file and not PCI config space. Most BIOSes
+ * virtualize the PCI registers so the chip looks like a standard IDE
+ * controller. Unfortunately not all implementations get this right.
+ * In particular some have problems with unaligned accesses to the
+ * virtualized PCI registers. This driver always does full dword
+ * writes to work around the issue. Also, in case of a bad BIOS this
+ * driver can be loaded with the "msr=1" parameter which forces using
+ * the Machine Specific Registers to configure the device.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/libata.h>
+#include <scsi/scsi_host.h>
+#include <asm/msr.h>
+
+#define DRV_NAME "pata_cs5536"
+#define DRV_VERSION "0.0.5"
+
+enum {
+ CFG = 0,
+ DTC = 1,
+ CAST = 2,
+ ETC = 3,
+
+ MSR_IDE_BASE = 0x51300000,
+ MSR_IDE_CFG = (MSR_IDE_BASE + 0x10),
+ MSR_IDE_DTC = (MSR_IDE_BASE + 0x12),
+ MSR_IDE_CAST = (MSR_IDE_BASE + 0x13),
+ MSR_IDE_ETC = (MSR_IDE_BASE + 0x14),
+
+ PCI_IDE_CFG = 0x40,
+ PCI_IDE_DTC = 0x48,
+ PCI_IDE_CAST = 0x4c,
+ PCI_IDE_ETC = 0x50,
+
+ IDE_CFG_CHANEN = 0x2,
+ IDE_CFG_CABLE = 0x10000,
+
+ IDE_D0_SHIFT = 24,
+ IDE_D1_SHIFT = 16,
+ IDE_DRV_MASK = 0xff,
+
+ IDE_CAST_D0_SHIFT = 6,
+ IDE_CAST_D1_SHIFT = 4,
+ IDE_CAST_DRV_MASK = 0x3,
+ IDE_CAST_CMD_MASK = 0xff,
+ IDE_CAST_CMD_SHIFT = 24,
+
+ IDE_ETC_NODMA = 0x03,
+};
+
+static int use_msr;
+
+static const u32 msr_reg[4] = {
+ MSR_IDE_CFG, MSR_IDE_DTC, MSR_IDE_CAST, MSR_IDE_ETC,
+};
+
+static const u8 pci_reg[4] = {
+ PCI_IDE_CFG, PCI_IDE_DTC, PCI_IDE_CAST, PCI_IDE_ETC,
+};
+
+static inline int cs5536_read(struct pci_dev *pdev, int reg, int *val)
+{
+ if (unlikely(use_msr)) {
+ u32 dummy;
+
+ rdmsr(msr_reg[reg], *val, dummy);
+ return 0;
+ }
+
+ return pci_read_config_dword(pdev, pci_reg[reg], val);
+}
+
+static inline int cs5536_write(struct pci_dev *pdev, int reg, int val)
+{
+ if (unlikely(use_msr)) {
+ wrmsr(msr_reg[reg], val, 0);
+ return 0;
+ }
+
+ return pci_write_config_dword(pdev, pci_reg[reg], val);
+}
+
+/**
+ * cs5536_cable_detect - detect cable type
+ * @ap: Port to detect on
+ * @deadline: deadline jiffies for the operation
+ *
+ * Perform cable detection for ATA66 capable cable. Return a libata
+ * cable type.
+ */
+
+static int cs5536_cable_detect(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u32 cfg;
+
+ cs5536_read(pdev, CFG, &cfg);
+
+ if (cfg & (IDE_CFG_CABLE << ap->port_no))
+ return ATA_CBL_PATA80;
+ else
+ return ATA_CBL_PATA40;
+}
+
+/**
+ * cs5536_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ */
+
+static void cs5536_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ static const u8 drv_timings[5] = {
+ 0x98, 0x55, 0x32, 0x21, 0x20,
+ };
+
+ static const u8 addr_timings[5] = {
+ 0x2, 0x1, 0x0, 0x0, 0x0,
+ };
+
+ static const u8 cmd_timings[5] = {
+ 0x99, 0x92, 0x90, 0x22, 0x20,
+ };
+
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ struct ata_device *pair = ata_dev_pair(adev);
+ int mode = adev->pio_mode - XFER_PIO_0;
+ int cmdmode = mode;
+ int dshift = ap->port_no ? IDE_D1_SHIFT : IDE_D0_SHIFT;
+ int cshift = ap->port_no ? IDE_CAST_D1_SHIFT : IDE_CAST_D0_SHIFT;
+ u32 dtc, cast, etc;
+
+ if (pair)
+ cmdmode = min(mode, pair->pio_mode - XFER_PIO_0);
+
+ cs5536_read(pdev, DTC, &dtc);
+ cs5536_read(pdev, CAST, &cast);
+ cs5536_read(pdev, ETC, &etc);
+
+ dtc &= ~(IDE_DRV_MASK << dshift);
+ dtc |= drv_timings[mode] << dshift;
+
+ cast &= ~(IDE_CAST_DRV_MASK << cshift);
+ cast |= addr_timings[mode] << cshift;
+
+ cast &= ~(IDE_CAST_CMD_MASK << IDE_CAST_CMD_SHIFT);
+ cast |= cmd_timings[cmdmode] << IDE_CAST_CMD_SHIFT;
+
+ etc &= ~(IDE_DRV_MASK << dshift);
+ etc |= IDE_ETC_NODMA << dshift;
+
+ cs5536_write(pdev, DTC, dtc);
+ cs5536_write(pdev, CAST, cast);
+ cs5536_write(pdev, ETC, etc);
+}
+
+/**
+ * cs5536_set_dmamode - DMA timing setup
+ * @ap: ATA interface
+ * @adev: Device being configured
+ *
+ */
+
+static void cs5536_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+ static const u8 udma_timings[6] = {
+ 0xc2, 0xc1, 0xc0, 0xc4, 0xc5, 0xc6,
+ };
+
+ static const u8 mwdma_timings[3] = {
+ 0x67, 0x21, 0x20,
+ };
+
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u32 dtc, etc;
+ int mode = adev->dma_mode;
+ int dshift = ap->port_no ? IDE_D1_SHIFT : IDE_D0_SHIFT;
+
+ if (mode >= XFER_UDMA_0) {
+ cs5536_read(pdev, ETC, &etc);
+
+ etc &= ~(IDE_DRV_MASK << dshift);
+ etc |= udma_timings[mode - XFER_UDMA_0] << dshift;
+
+ cs5536_write(pdev, ETC, etc);
+ } else { /* MWDMA */
+ cs5536_read(pdev, DTC, &dtc);
+
+ dtc &= ~(IDE_DRV_MASK << dshift);
+ dtc |= mwdma_timings[mode] << dshift;
+
+ cs5536_write(pdev, DTC, dtc);
+ }
+}
+
+static struct scsi_host_template cs5536_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
+ .bios_param = ata_std_bios_param,
+};
+
+static struct ata_port_operations cs5536_port_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = cs5536_set_piomode,
+ .set_dmamode = cs5536_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = ata_bmdma_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = cs5536_cable_detect,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+
+ .data_xfer = ata_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
+
+ .port_start = ata_port_start,
+};
+
+/**
+ * cs5536_init_one
+ * @dev: PCI device
+ * @id: Entry in match table
+ *
+ */
+
+static int cs5536_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+ static const struct ata_port_info info = {
+ .sht = &cs5536_sht,
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = 0x1f,
+ .mwdma_mask = 0x07,
+ .udma_mask = ATA_UDMA5,
+ .port_ops = &cs5536_port_ops,
+ };
+
+ const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
+ u32 cfg;
+
+ if (use_msr)
+ printk(KERN_ERR DRV_NAME ": Using MSR regs instead of PCI\n");
+
+ cs5536_read(dev, CFG, &cfg);
+
+ if ((cfg & IDE_CFG_CHANEN) == 0) {
+ printk(KERN_ERR DRV_NAME ": disabled by BIOS\n");
+ return -ENODEV;
+ }
+
+ return ata_pci_init_one(dev, ppi);
+}
+
+static const struct pci_device_id cs5536[] = {
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_CS5536_IDE), },
+ { },
+};
+
+static struct pci_driver cs5536_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = cs5536,
+ .probe = cs5536_init_one,
+ .remove = ata_pci_remove_one,
+#ifdef CONFIG_PM
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
+#endif
+};
+
+static int __init cs5536_init(void)
+{
+ return pci_register_driver(&cs5536_pci_driver);
+}
+
+static void __exit cs5536_exit(void)
+{
+ pci_unregister_driver(&cs5536_pci_driver);
+}
+
+MODULE_AUTHOR("Martin K. Petersen");
+MODULE_DESCRIPTION("low-level driver for the CS5536 IDE controller");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, cs5536);
+MODULE_VERSION(DRV_VERSION);
+module_param_named(msr, use_msr, int, 0644);
+MODULE_PARM_DESC(msr, "Force using MSR to configure IDE function (Default: 0)");
+
+module_init(cs5536_init);
+module_exit(cs5536_exit);
diff --git a/drivers/ata/pata_pcmcia.c b/drivers/ata/pata_pcmcia.c
index 782ff4a..5db2013 100644
--- a/drivers/ata/pata_pcmcia.c
+++ b/drivers/ata/pata_pcmcia.c
@@ -353,6 +353,7 @@ static void pcmcia_remove_one(struct pcmcia_device *pdev)
static struct pcmcia_device_id pcmcia_devices[] = {
PCMCIA_DEVICE_FUNC_ID(4),
+ PCMCIA_DEVICE_MANF_CARD(0x0000, 0x0000), /* Corsair */
PCMCIA_DEVICE_MANF_CARD(0x0007, 0x0000), /* Hitachi */
PCMCIA_DEVICE_MANF_CARD(0x000a, 0x0000), /* I-O Data CFA */
PCMCIA_DEVICE_MANF_CARD(0x001c, 0x0001), /* Mitsubishi CFA */
@@ -378,6 +379,7 @@ static struct pcmcia_device_id pcmcia_devices[] = {
PCMCIA_DEVICE_PROD_ID12("EXP ", "CD-ROM", 0x0a5c52fd, 0x66536591),
PCMCIA_DEVICE_PROD_ID12("EXP ", "PnPIDE", 0x0a5c52fd, 0x0c694728),
PCMCIA_DEVICE_PROD_ID12("FREECOM", "PCCARD-IDE", 0x5714cbf7, 0x48e0ab8e),
+ PCMCIA_DEVICE_PROD_ID12("Hyperstone", "Model1", 0x3d5b9ef5, 0xca6ab420),
PCMCIA_DEVICE_PROD_ID12("HITACHI", "FLASH", 0xf4f43949, 0x9eb86aae),
PCMCIA_DEVICE_PROD_ID12("HITACHI", "microdrive", 0xf4f43949, 0xa6d76178),
PCMCIA_DEVICE_PROD_ID12("IBM", "microdrive", 0xb569a6e5, 0xa6d76178),
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index 2eb75cd..4dc2e73 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -279,7 +279,7 @@ static struct ata_port_operations sil680_port_ops = {
* Returns the final clock settings.
*/
-static u8 sil680_init_chip(struct pci_dev *pdev)
+static u8 sil680_init_chip(struct pci_dev *pdev, int *try_mmio)
{
u32 class_rev = 0;
u8 tmpbyte = 0;
@@ -297,6 +297,8 @@ static u8 sil680_init_chip(struct pci_dev *pdev)
dev_dbg(&pdev->dev, "sil680: BA5_EN = %d clock = %02X\n",
tmpbyte & 1, tmpbyte & 0x30);
+ *try_mmio = (tmpbyte & 1) || pci_resource_start(pdev, 5);
+
switch(tmpbyte & 0x30) {
case 0x00:
/* 133 clock attempt to force it on */
@@ -361,25 +363,76 @@ static int __devinit sil680_init_one(struct pci_dev *pdev,
};
const struct ata_port_info *ppi[] = { &info, NULL };
static int printed_version;
+ struct ata_host *host;
+ void __iomem *mmio_base;
+ int rc, try_mmio;
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
- switch(sil680_init_chip(pdev))
- {
+ switch (sil680_init_chip(pdev, &try_mmio)) {
case 0:
ppi[0] = &info_slow;
break;
case 0x30:
return -ENODEV;
}
+
+ if (!try_mmio)
+ goto use_ioports;
+
+ /* Try to acquire MMIO resources and fallback to PIO if
+ * that fails
+ */
+ rc = pcim_enable_device(pdev);
+ if (rc)
+ return rc;
+ rc = pcim_iomap_regions(pdev, 1 << SIL680_MMIO_BAR, DRV_NAME);
+ if (rc)
+ goto use_ioports;
+
+ /* Allocate host and set it up */
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
+ if (!host)
+ return -ENOMEM;
+ host->iomap = pcim_iomap_table(pdev);
+
+ /* Setup DMA masks */
+ rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+ if (rc)
+ return rc;
+ rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+ if (rc)
+ return rc;
+ pci_set_master(pdev);
+
+ /* Get MMIO base and initialize port addresses */
+ mmio_base = host->iomap[SIL680_MMIO_BAR];
+ host->ports[0]->ioaddr.bmdma_addr = mmio_base + 0x00;
+ host->ports[0]->ioaddr.cmd_addr = mmio_base + 0x80;
+ host->ports[0]->ioaddr.ctl_addr = mmio_base + 0x8a;
+ host->ports[0]->ioaddr.altstatus_addr = mmio_base + 0x8a;
+ ata_std_ports(&host->ports[0]->ioaddr);
+ host->ports[1]->ioaddr.bmdma_addr = mmio_base + 0x08;
+ host->ports[1]->ioaddr.cmd_addr = mmio_base + 0xc0;
+ host->ports[1]->ioaddr.ctl_addr = mmio_base + 0xca;
+ host->ports[1]->ioaddr.altstatus_addr = mmio_base + 0xca;
+ ata_std_ports(&host->ports[1]->ioaddr);
+
+ /* Register & activate */
+ return ata_host_activate(host, pdev->irq, ata_interrupt, IRQF_SHARED,
+ &sil680_sht);
+
+use_ioports:
return ata_pci_init_one(pdev, ppi);
}
#ifdef CONFIG_PM
static int sil680_reinit_one(struct pci_dev *pdev)
{
- sil680_init_chip(pdev);
+ int try_mmio;
+
+ sil680_init_chip(pdev, &try_mmio);
return ata_pci_device_resume(pdev);
}
#endif
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 40557fe..240a892 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -169,6 +169,35 @@ enum {
NV_ADMA_PORT_REGISTER_MODE = (1 << 0),
NV_ADMA_ATAPI_SETUP_COMPLETE = (1 << 1),
+ /* MCP55 reg offset */
+ NV_CTL_MCP55 = 0x400,
+ NV_INT_STATUS_MCP55 = 0x440,
+ NV_INT_ENABLE_MCP55 = 0x444,
+ NV_NCQ_REG_MCP55 = 0x448,
+
+ /* MCP55 */
+ NV_INT_ALL_MCP55 = 0xffff,
+ NV_INT_PORT_SHIFT_MCP55 = 16, /* each port occupies 16 bits */
+ NV_INT_MASK_MCP55 = NV_INT_ALL_MCP55 & 0xfffd,
+
+ /* SWNCQ ENABLE BITS*/
+ NV_CTL_PRI_SWNCQ = 0x02,
+ NV_CTL_SEC_SWNCQ = 0x04,
+
+ /* SW NCQ status bits*/
+ NV_SWNCQ_IRQ_DEV = (1 << 0),
+ NV_SWNCQ_IRQ_PM = (1 << 1),
+ NV_SWNCQ_IRQ_ADDED = (1 << 2),
+ NV_SWNCQ_IRQ_REMOVED = (1 << 3),
+
+ NV_SWNCQ_IRQ_BACKOUT = (1 << 4),
+ NV_SWNCQ_IRQ_SDBFIS = (1 << 5),
+ NV_SWNCQ_IRQ_DHREGFIS = (1 << 6),
+ NV_SWNCQ_IRQ_DMASETUP = (1 << 7),
+
+ NV_SWNCQ_IRQ_HOTPLUG = NV_SWNCQ_IRQ_ADDED |
+ NV_SWNCQ_IRQ_REMOVED,
+
};
/* ADMA Physical Region Descriptor - one SG segment */
@@ -226,6 +255,42 @@ struct nv_host_priv {
unsigned long type;
};
+struct defer_queue {
+ u32 defer_bits;
+ unsigned int head;
+ unsigned int tail;
+ unsigned int tag[ATA_MAX_QUEUE];
+};
+
+enum ncq_saw_flag_list {
+ ncq_saw_d2h = (1U << 0),
+ ncq_saw_dmas = (1U << 1),
+ ncq_saw_sdb = (1U << 2),
+ ncq_saw_backout = (1U << 3),
+};
+
+struct nv_swncq_port_priv {
+ struct ata_prd *prd; /* our SG list */
+ dma_addr_t prd_dma; /* and its DMA mapping */
+ void __iomem *sactive_block;
+ void __iomem *irq_block;
+ void __iomem *tag_block;
+ u32 qc_active;
+
+ unsigned int last_issue_tag;
+
+ /* fifo circular queue to store deferral command */
+ struct defer_queue defer_queue;
+
+ /* for NCQ interrupt analysis */
+ u32 dhfis_bits;
+ u32 dmafis_bits;
+ u32 sdbfis_bits;
+
+ unsigned int ncq_flags;
+};
+
+
#define NV_ADMA_CHECK_INTR(GCTL, PORT) ((GCTL) & ( 1 << (19 + (12 * (PORT)))))
static int nv_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
@@ -263,13 +328,29 @@ static void nv_adma_host_stop(struct ata_host *host);
static void nv_adma_post_internal_cmd(struct ata_queued_cmd *qc);
static void nv_adma_tf_read(struct ata_port *ap, struct ata_taskfile *tf);
+static void nv_mcp55_thaw(struct ata_port *ap);
+static void nv_mcp55_freeze(struct ata_port *ap);
+static void nv_swncq_error_handler(struct ata_port *ap);
+static int nv_swncq_slave_config(struct scsi_device *sdev);
+static int nv_swncq_port_start(struct ata_port *ap);
+static void nv_swncq_qc_prep(struct ata_queued_cmd *qc);
+static void nv_swncq_fill_sg(struct ata_queued_cmd *qc);
+static unsigned int nv_swncq_qc_issue(struct ata_queued_cmd *qc);
+static void nv_swncq_irq_clear(struct ata_port *ap, u16 fis);
+static irqreturn_t nv_swncq_interrupt(int irq, void *dev_instance);
+#ifdef CONFIG_PM
+static int nv_swncq_port_suspend(struct ata_port *ap, pm_message_t mesg);
+static int nv_swncq_port_resume(struct ata_port *ap);
+#endif
+
enum nv_host_type
{
GENERIC,
NFORCE2,
NFORCE3 = NFORCE2, /* NF2 == NF3 as far as sata_nv is concerned */
CK804,
- ADMA
+ ADMA,
+ SWNCQ,
};
static const struct pci_device_id nv_pci_tbl[] = {
@@ -280,13 +361,13 @@ static const struct pci_device_id nv_pci_tbl[] = {
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_SATA2), CK804 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_SATA), CK804 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_SATA2), CK804 },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA), GENERIC },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2), GENERIC },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA), GENERIC },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA2), GENERIC },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA), GENERIC },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA2), GENERIC },
- { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA3), GENERIC },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA), SWNCQ },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2), SWNCQ },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA), SWNCQ },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA2), SWNCQ },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA), SWNCQ },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA2), SWNCQ },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA3), SWNCQ },
{ } /* terminate list */
};
@@ -339,6 +420,25 @@ static struct scsi_host_template nv_adma_sht = {
.bios_param = ata_std_bios_param,
};
+static struct scsi_host_template nv_swncq_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .change_queue_depth = ata_scsi_change_queue_depth,
+ .can_queue = ATA_MAX_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = nv_swncq_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
+ .bios_param = ata_std_bios_param,
+};
+
static const struct ata_port_operations nv_generic_ops = {
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
@@ -444,6 +544,35 @@ static const struct ata_port_operations nv_adma_ops = {
.host_stop = nv_adma_host_stop,
};
+static const struct ata_port_operations nv_swncq_ops = {
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .exec_command = ata_exec_command,
+ .check_status = ata_check_status,
+ .dev_select = ata_std_dev_select,
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_defer = ata_std_qc_defer,
+ .qc_prep = nv_swncq_qc_prep,
+ .qc_issue = nv_swncq_qc_issue,
+ .freeze = nv_mcp55_freeze,
+ .thaw = nv_mcp55_thaw,
+ .error_handler = nv_swncq_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .data_xfer = ata_data_xfer,
+ .irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .scr_read = nv_scr_read,
+ .scr_write = nv_scr_write,
+#ifdef CONFIG_PM
+ .port_suspend = nv_swncq_port_suspend,
+ .port_resume = nv_swncq_port_resume,
+#endif
+ .port_start = nv_swncq_port_start,
+};
+
static const struct ata_port_info nv_port_info[] = {
/* generic */
{
@@ -490,6 +619,18 @@ static const struct ata_port_info nv_port_info[] = {
.port_ops = &nv_adma_ops,
.irq_handler = nv_adma_interrupt,
},
+ /* SWNCQ */
+ {
+ .sht = &nv_swncq_sht,
+ .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+ ATA_FLAG_NCQ,
+ .link_flags = ATA_LFLAG_HRST_TO_RESUME,
+ .pio_mask = NV_PIO_MASK,
+ .mwdma_mask = NV_MWDMA_MASK,
+ .udma_mask = NV_UDMA_MASK,
+ .port_ops = &nv_swncq_ops,
+ .irq_handler = nv_swncq_interrupt,
+ },
};
MODULE_AUTHOR("NVIDIA");
@@ -499,6 +640,7 @@ MODULE_DEVICE_TABLE(pci, nv_pci_tbl);
MODULE_VERSION(DRV_VERSION);
static int adma_enabled = 1;
+static int swncq_enabled;
static void nv_adma_register_mode(struct ata_port *ap)
{
@@ -1452,6 +1594,34 @@ static void nv_ck804_thaw(struct ata_port *ap)
writeb(mask, mmio_base + NV_INT_ENABLE_CK804);
}
+static void nv_mcp55_freeze(struct ata_port *ap)
+{
+ void __iomem *mmio_base = ap->host->iomap[NV_MMIO_BAR];
+ int shift = ap->port_no * NV_INT_PORT_SHIFT_MCP55;
+ u32 mask;
+
+ writel(NV_INT_ALL_MCP55 << shift, mmio_base + NV_INT_STATUS_MCP55);
+
+ mask = readl(mmio_base + NV_INT_ENABLE_MCP55);
+ mask &= ~(NV_INT_ALL_MCP55 << shift);
+ writel(mask, mmio_base + NV_INT_ENABLE_MCP55);
+ ata_bmdma_freeze(ap);
+}
+
+static void nv_mcp55_thaw(struct ata_port *ap)
+{
+ void __iomem *mmio_base = ap->host->iomap[NV_MMIO_BAR];
+ int shift = ap->port_no * NV_INT_PORT_SHIFT_MCP55;
+ u32 mask;
+
+ writel(NV_INT_ALL_MCP55 << shift, mmio_base + NV_INT_STATUS_MCP55);
+
+ mask = readl(mmio_base + NV_INT_ENABLE_MCP55);
+ mask |= (NV_INT_MASK_MCP55 << shift);
+ writel(mask, mmio_base + NV_INT_ENABLE_MCP55);
+ ata_bmdma_thaw(ap);
+}
+
static int nv_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline)
{
@@ -1525,6 +1695,663 @@ static void nv_adma_error_handler(struct ata_port *ap)
nv_hardreset, ata_std_postreset);
}
+static void nv_swncq_qc_to_dq(struct ata_port *ap, struct ata_queued_cmd *qc)
+{
+ struct nv_swncq_port_priv *pp = ap->private_data;
+ struct defer_queue *dq = &pp->defer_queue;
+
+ /* queue is full */
+ WARN_ON(dq->tail - dq->head == ATA_MAX_QUEUE);
+ dq->defer_bits |= (1 << qc->tag);
+ dq->tag[dq->tail++ & (ATA_MAX_QUEUE - 1)] = qc->tag;
+}
+
+static struct ata_queued_cmd *nv_swncq_qc_from_dq(struct ata_port *ap)
+{
+ struct nv_swncq_port_priv *pp = ap->private_data;
+ struct defer_queue *dq = &pp->defer_queue;
+ unsigned int tag;
+
+ if (dq->head == dq->tail) /* null queue */
+ return NULL;
+
+ tag = dq->tag[dq->head & (ATA_MAX_QUEUE - 1)];
+ dq->tag[dq->head++ & (ATA_MAX_QUEUE - 1)] = ATA_TAG_POISON;
+ WARN_ON(!(dq->defer_bits & (1 << tag)));
+ dq->defer_bits &= ~(1 << tag);
+
+ return ata_qc_from_tag(ap, tag);
+}
+
+static void nv_swncq_fis_reinit(struct ata_port *ap)
+{
+ struct nv_swncq_port_priv *pp = ap->private_data;
+
+ pp->dhfis_bits = 0;
+ pp->dmafis_bits = 0;
+ pp->sdbfis_bits = 0;
+ pp->ncq_flags = 0;
+}
+
+static void nv_swncq_pp_reinit(struct ata_port *ap)
+{
+ struct nv_swncq_port_priv *pp = ap->private_data;
+ struct defer_queue *dq = &pp->defer_queue;
+
+ dq->head = 0;
+ dq->tail = 0;
+ dq->defer_bits = 0;
+ pp->qc_active = 0;
+ pp->last_issue_tag = ATA_TAG_POISON;
+ nv_swncq_fis_reinit(ap);
+}
+
+static void nv_swncq_irq_clear(struct ata_port *ap, u16 fis)
+{
+ struct nv_swncq_port_priv *pp = ap->private_data;
+
+ writew(fis, pp->irq_block);
+}
+
+static void __ata_bmdma_stop(struct ata_port *ap)
+{
+ struct ata_queued_cmd qc;
+
+ qc.ap = ap;
+ ata_bmdma_stop(&qc);
+}
+
+static void nv_swncq_ncq_stop(struct ata_port *ap)
+{
+ struct nv_swncq_port_priv *pp = ap->private_data;
+ unsigned int i;
+ u32 sactive;
+ u32 done_mask;
+
+ ata_port_printk(ap, KERN_ERR,
+ "EH in SWNCQ mode,QC:qc_active 0x%X sactive 0x%X\n",
+ ap->qc_active, ap->link.sactive);
+ ata_port_printk(ap, KERN_ERR,
+ "SWNCQ:qc_active 0x%X defer_bits 0x%X last_issue_tag 0x%x\n "
+ "dhfis 0x%X dmafis 0x%X sdbfis 0x%X\n",
+ pp->qc_active, pp->defer_queue.defer_bits, pp->last_issue_tag,
+ pp->dhfis_bits, pp->dmafis_bits, pp->sdbfis_bits);
+
+ ata_port_printk(ap, KERN_ERR, "ATA_REG 0x%X ERR_REG 0x%X\n",
+ ap->ops->check_status(ap),
+ ioread8(ap->ioaddr.error_addr));
+
+ sactive = readl(pp->sactive_block);
+ done_mask = pp->qc_active ^ sactive;
+
+ ata_port_printk(ap, KERN_ERR, "tag : dhfis dmafis sdbfis sacitve\n");
+ for (i = 0; i < ATA_MAX_QUEUE; i++) {
+ u8 err = 0;
+ if (pp->qc_active & (1 << i))
+ err = 0;
+ else if (done_mask & (1 << i))
+ err = 1;
+ else
+ continue;
+
+ ata_port_printk(ap, KERN_ERR,
+ "tag 0x%x: %01x %01x %01x %01x %s\n", i,
+ (pp->dhfis_bits >> i) & 0x1,
+ (pp->dmafis_bits >> i) & 0x1,
+ (pp->sdbfis_bits >> i) & 0x1,
+ (sactive >> i) & 0x1,
+ (err ? "error! tag doesn't exit" : " "));
+ }
+
+ nv_swncq_pp_reinit(ap);
+ ap->ops->irq_clear(ap);
+ __ata_bmdma_stop(ap);
+ nv_swncq_irq_clear(ap, 0xffff);
+}
+
+static void nv_swncq_error_handler(struct ata_port *ap)
+{
+ struct ata_eh_context *ehc = &ap->link.eh_context;
+
+ if (ap->link.sactive) {
+ nv_swncq_ncq_stop(ap);
+ ehc->i.action |= ATA_EH_HARDRESET;
+ }
+
+ ata_bmdma_drive_eh(ap, ata_std_prereset, ata_std_softreset,
+ nv_hardreset, ata_std_postreset);
+}
+
+#ifdef CONFIG_PM
+static int nv_swncq_port_suspend(struct ata_port *ap, pm_message_t mesg)
+{
+ void __iomem *mmio = ap->host->iomap[NV_MMIO_BAR];
+ u32 tmp;
+
+ /* clear irq */
+ writel(~0, mmio + NV_INT_STATUS_MCP55);
+
+ /* disable irq */
+ writel(0, mmio + NV_INT_ENABLE_MCP55);
+
+ /* disable swncq */
+ tmp = readl(mmio + NV_CTL_MCP55);
+ tmp &= ~(NV_CTL_PRI_SWNCQ | NV_CTL_SEC_SWNCQ);
+ writel(tmp, mmio + NV_CTL_MCP55);
+
+ return 0;
+}
+
+static int nv_swncq_port_resume(struct ata_port *ap)
+{
+ void __iomem *mmio = ap->host->iomap[NV_MMIO_BAR];
+ u32 tmp;
+
+ /* clear irq */
+ writel(~0, mmio + NV_INT_STATUS_MCP55);
+
+ /* enable irq */
+ writel(0x00fd00fd, mmio + NV_INT_ENABLE_MCP55);
+
+ /* enable swncq */
+ tmp = readl(mmio + NV_CTL_MCP55);
+ writel(tmp | NV_CTL_PRI_SWNCQ | NV_CTL_SEC_SWNCQ, mmio + NV_CTL_MCP55);
+
+ return 0;
+}
+#endif
+
+static void nv_swncq_host_init(struct ata_host *host)
+{
+ u32 tmp;
+ void __iomem *mmio = host->iomap[NV_MMIO_BAR];
+ struct pci_dev *pdev = to_pci_dev(host->dev);
+ u8 regval;
+
+ /* disable ECO 398 */
+ pci_read_config_byte(pdev, 0x7f, ®val);
+ regval &= ~(1 << 7);
+ pci_write_config_byte(pdev, 0x7f, regval);
+
+ /* enable swncq */
+ tmp = readl(mmio + NV_CTL_MCP55);
+ VPRINTK("HOST_CTL:0x%X\n", tmp);
+ writel(tmp | NV_CTL_PRI_SWNCQ | NV_CTL_SEC_SWNCQ, mmio + NV_CTL_MCP55);
+
+ /* enable irq intr */
+ tmp = readl(mmio + NV_INT_ENABLE_MCP55);
+ VPRINTK("HOST_ENABLE:0x%X\n", tmp);
+ writel(tmp | 0x00fd00fd, mmio + NV_INT_ENABLE_MCP55);
+
+ /* clear port irq */
+ writel(~0x0, mmio + NV_INT_STATUS_MCP55);
+}
+
+static int nv_swncq_slave_config(struct scsi_device *sdev)
+{
+ struct ata_port *ap = ata_shost_to_port(sdev->host);
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ struct ata_device *dev;
+ int rc;
+ u8 rev;
+ u8 check_maxtor = 0;
+ unsigned char model_num[ATA_ID_PROD_LEN + 1];
+
+ rc = ata_scsi_slave_config(sdev);
+ if (sdev->id >= ATA_MAX_DEVICES || sdev->channel || sdev->lun)
+ /* Not a proper libata device, ignore */
+ return rc;
+
+ dev = &ap->link.device[sdev->id];
+ if (!(ap->flags & ATA_FLAG_NCQ) || dev->class == ATA_DEV_ATAPI)
+ return rc;
+
+ /* if MCP51 and Maxtor, then disable ncq */
+ if (pdev->device == PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA ||
+ pdev->device == PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2)
+ check_maxtor = 1;
+
+ /* if MCP55 and rev <= a2 and Maxtor, then disable ncq */
+ if (pdev->device == PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA ||
+ pdev->device == PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA2) {
+ pci_read_config_byte(pdev, 0x8, &rev);
+ if (rev <= 0xa2)
+ check_maxtor = 1;
+ }
+
+ if (!check_maxtor)
+ return rc;
+
+ ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));
+
+ if (strncmp(model_num, "Maxtor", 6) == 0) {
+ ata_scsi_change_queue_depth(sdev, 1);
+ ata_dev_printk(dev, KERN_NOTICE,
+ "Disabling SWNCQ mode (depth %x)\n", sdev->queue_depth);
+ }
+
+ return rc;
+}
+
+static int nv_swncq_port_start(struct ata_port *ap)
+{
+ struct device *dev = ap->host->dev;
+ void __iomem *mmio = ap->host->iomap[NV_MMIO_BAR];
+ struct nv_swncq_port_priv *pp;
+ int rc;
+
+ rc = ata_port_start(ap);
+ if (rc)
+ return rc;
+
+ pp = devm_kzalloc(dev, sizeof(*pp), GFP_KERNEL);
+ if (!pp)
+ return -ENOMEM;
+
+ pp->prd = dmam_alloc_coherent(dev, ATA_PRD_TBL_SZ * ATA_MAX_QUEUE,
+ &pp->prd_dma, GFP_KERNEL);
+ if (!pp->prd)
+ return -ENOMEM;
+ memset(pp->prd, 0, ATA_PRD_TBL_SZ * ATA_MAX_QUEUE);
+
+ ap->private_data = pp;
+ pp->sactive_block = ap->ioaddr.scr_addr + 4 * SCR_ACTIVE;
+ pp->irq_block = mmio + NV_INT_STATUS_MCP55 + ap->port_no * 2;
+ pp->tag_block = mmio + NV_NCQ_REG_MCP55 + ap->port_no * 2;
+
+ return 0;
+}
+
+static void nv_swncq_qc_prep(struct ata_queued_cmd *qc)
+{
+ if (qc->tf.protocol != ATA_PROT_NCQ) {
+ ata_qc_prep(qc);
+ return;
+ }
+
+ if (!(qc->flags & ATA_QCFLAG_DMAMAP))
+ return;
+
+ nv_swncq_fill_sg(qc);
+}
+
+static void nv_swncq_fill_sg(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct scatterlist *sg;
+ unsigned int idx;
+ struct nv_swncq_port_priv *pp = ap->private_data;
+ struct ata_prd *prd;
+
+ WARN_ON(qc->__sg == NULL);
+ WARN_ON(qc->n_elem == 0 && qc->pad_len == 0);
+
+ prd = pp->prd + ATA_MAX_PRD * qc->tag;
+
+ idx = 0;
+ ata_for_each_sg(sg, qc) {
+ u32 addr, offset;
+ u32 sg_len, len;
+
+ addr = (u32)sg_dma_address(sg);
+ sg_len = sg_dma_len(sg);
+
+ while (sg_len) {
+ offset = addr & 0xffff;
+ len = sg_len;
+ if ((offset + sg_len) > 0x10000)
+ len = 0x10000 - offset;
+
+ prd[idx].addr = cpu_to_le32(addr);
+ prd[idx].flags_len = cpu_to_le32(len & 0xffff);
+
+ idx++;
+ sg_len -= len;
+ addr += len;
+ }
+ }
+
+ if (idx)
+ prd[idx - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
+}
+
+static unsigned int nv_swncq_issue_atacmd(struct ata_port *ap,
+ struct ata_queued_cmd *qc)
+{
+ struct nv_swncq_port_priv *pp = ap->private_data;
+
+ if (qc == NULL)
+ return 0;
+
+ DPRINTK("Enter\n");
+
+ writel((1 << qc->tag), pp->sactive_block);
+ pp->last_issue_tag = qc->tag;
+ pp->dhfis_bits &= ~(1 << qc->tag);
+ pp->dmafis_bits &= ~(1 << qc->tag);
+ pp->qc_active |= (0x1 << qc->tag);
+
+ ap->ops->tf_load(ap, &qc->tf); /* load tf registers */
+ ap->ops->exec_command(ap, &qc->tf);
+
+ DPRINTK("Issued tag %u\n", qc->tag);
+
+ return 0;
+}
+
+static unsigned int nv_swncq_qc_issue(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct nv_swncq_port_priv *pp = ap->private_data;
+
+ if (qc->tf.protocol != ATA_PROT_NCQ)
+ return ata_qc_issue_prot(qc);
+
+ DPRINTK("Enter\n");
+
+ if (!pp->qc_active)
+ nv_swncq_issue_atacmd(ap, qc);
+ else
+ nv_swncq_qc_to_dq(ap, qc); /* add qc to defer queue */
+
+ return 0;
+}
+
+static void nv_swncq_hotplug(struct ata_port *ap, u32 fis)
+{
+ u32 serror;
+ struct ata_eh_info *ehi = &ap->link.eh_info;
+
+ ata_ehi_clear_desc(ehi);
+
+ /* AHCI needs SError cleared; otherwise, it might lock up */
+ sata_scr_read(&ap->link, SCR_ERROR, &serror);
+ sata_scr_write(&ap->link, SCR_ERROR, serror);
+
+ /* analyze @irq_stat */
+ if (fis & NV_SWNCQ_IRQ_ADDED)
+ ata_ehi_push_desc(ehi, "hot plug");
+ else if (fis & NV_SWNCQ_IRQ_REMOVED)
+ ata_ehi_push_desc(ehi, "hot unplug");
+
+ ata_ehi_hotplugged(ehi);
+
+ /* okay, let's hand over to EH */
+ ehi->serror |= serror;
+
+ ata_port_freeze(ap);
+}
+
+static int nv_swncq_sdbfis(struct ata_port *ap)
+{
+ struct ata_queued_cmd *qc;
+ struct nv_swncq_port_priv *pp = ap->private_data;
+ struct ata_eh_info *ehi = &ap->link.eh_info;
+ u32 sactive;
+ int nr_done = 0;
+ u32 done_mask;
+ int i;
+ u8 host_stat;
+ u8 lack_dhfis = 0;
+
+ host_stat = ap->ops->bmdma_status(ap);
+ if (unlikely(host_stat & ATA_DMA_ERR)) {
+ /* error when transfering data to/from memory */
+ ata_ehi_clear_desc(ehi);
+ ata_ehi_push_desc(ehi, "BMDMA stat 0x%x", host_stat);
+ ehi->err_mask |= AC_ERR_HOST_BUS;
+ ehi->action |= ATA_EH_SOFTRESET;
+ return -EINVAL;
+ }
+
+ ap->ops->irq_clear(ap);
+ __ata_bmdma_stop(ap);
+
+ sactive = readl(pp->sactive_block);
+ done_mask = pp->qc_active ^ sactive;
+
+ if (unlikely(done_mask & sactive)) {
+ ata_ehi_clear_desc(ehi);
+ ata_ehi_push_desc(ehi, "illegal SWNCQ:qc_active transition"
+ "(%08x->%08x)", pp->qc_active, sactive);
+ ehi->err_mask |= AC_ERR_HSM;
+ ehi->action |= ATA_EH_HARDRESET;
+ return -EINVAL;
+ }
+ for (i = 0; i < ATA_MAX_QUEUE; i++) {
+ if (!(done_mask & (1 << i)))
+ continue;
+
+ qc = ata_qc_from_tag(ap, i);
+ if (qc) {
+ ata_qc_complete(qc);
+ pp->qc_active &= ~(1 << i);
+ pp->dhfis_bits &= ~(1 << i);
+ pp->dmafis_bits &= ~(1 << i);
+ pp->sdbfis_bits |= (1 << i);
+ nr_done++;
+ }
+ }
+
+ if (!ap->qc_active) {
+ DPRINTK("over\n");
+ nv_swncq_pp_reinit(ap);
+ return nr_done;
+ }
+
+ if (pp->qc_active & pp->dhfis_bits)
+ return nr_done;
+
+ if ((pp->ncq_flags & ncq_saw_backout) ||
+ (pp->qc_active ^ pp->dhfis_bits))
+ /* if the controller cann't get a device to host register FIS,
+ * The driver needs to reissue the new command.
+ */
+ lack_dhfis = 1;
+
+ DPRINTK("id 0x%x QC: qc_active 0x%x,"
+ "SWNCQ:qc_active 0x%X defer_bits %X "
+ "dhfis 0x%X dmafis 0x%X last_issue_tag %x\n",
+ ap->print_id, ap->qc_active, pp->qc_active,
+ pp->defer_queue.defer_bits, pp->dhfis_bits,
+ pp->dmafis_bits, pp->last_issue_tag);
+
+ nv_swncq_fis_reinit(ap);
+
+ if (lack_dhfis) {
+ qc = ata_qc_from_tag(ap, pp->last_issue_tag);
+ nv_swncq_issue_atacmd(ap, qc);
+ return nr_done;
+ }
+
+ if (pp->defer_queue.defer_bits) {
+ /* send deferral queue command */
+ qc = nv_swncq_qc_from_dq(ap);
+ WARN_ON(qc == NULL);
+ nv_swncq_issue_atacmd(ap, qc);
+ }
+
+ return nr_done;
+}
+
+static inline u32 nv_swncq_tag(struct ata_port *ap)
+{
+ struct nv_swncq_port_priv *pp = ap->private_data;
+ u32 tag;
+
+ tag = readb(pp->tag_block) >> 2;
+ return (tag & 0x1f);
+}
+
+static int nv_swncq_dmafis(struct ata_port *ap)
+{
+ struct ata_queued_cmd *qc;
+ unsigned int rw;
+ u8 dmactl;
+ u32 tag;
+ struct nv_swncq_port_priv *pp = ap->private_data;
+
+ __ata_bmdma_stop(ap);
+ tag = nv_swncq_tag(ap);
+
+ DPRINTK("dma setup tag 0x%x\n", tag);
+ qc = ata_qc_from_tag(ap, tag);
+
+ if (unlikely(!qc))
+ return 0;
+
+ rw = qc->tf.flags & ATA_TFLAG_WRITE;
+
+ /* load PRD table addr. */
+ iowrite32(pp->prd_dma + ATA_PRD_TBL_SZ * qc->tag,
+ ap->ioaddr.bmdma_addr + ATA_DMA_TABLE_OFS);
+
+ /* specify data direction, triple-check start bit is clear */
+ dmactl = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+ dmactl &= ~ATA_DMA_WR;
+ if (!rw)
+ dmactl |= ATA_DMA_WR;
+
+ iowrite8(dmactl | ATA_DMA_START, ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+
+ return 1;
+}
+
+static void nv_swncq_host_interrupt(struct ata_port *ap, u16 fis)
+{
+ struct nv_swncq_port_priv *pp = ap->private_data;
+ struct ata_queued_cmd *qc;
+ struct ata_eh_info *ehi = &ap->link.eh_info;
+ u32 serror;
+ u8 ata_stat;
+ int rc = 0;
+
+ ata_stat = ap->ops->check_status(ap);
+ nv_swncq_irq_clear(ap, fis);
+ if (!fis)
+ return;
+
+ if (ap->pflags & ATA_PFLAG_FROZEN)
+ return;
+
+ if (fis & NV_SWNCQ_IRQ_HOTPLUG) {
+ nv_swncq_hotplug(ap, fis);
+ return;
+ }
+
+ if (!pp->qc_active)
+ return;
+
+ if (ap->ops->scr_read(ap, SCR_ERROR, &serror))
+ return;
+ ap->ops->scr_write(ap, SCR_ERROR, serror);
+
+ if (ata_stat & ATA_ERR) {
+ ata_ehi_clear_desc(ehi);
+ ata_ehi_push_desc(ehi, "Ata error. fis:0x%X", fis);
+ ehi->err_mask |= AC_ERR_DEV;
+ ehi->serror |= serror;
+ ehi->action |= ATA_EH_SOFTRESET;
+ ata_port_freeze(ap);
+ return;
+ }
+
+ if (fis & NV_SWNCQ_IRQ_BACKOUT) {
+ /* If the IRQ is backout, driver must issue
+ * the new command again some time later.
+ */
+ pp->ncq_flags |= ncq_saw_backout;
+ }
+
+ if (fis & NV_SWNCQ_IRQ_SDBFIS) {
+ pp->ncq_flags |= ncq_saw_sdb;
+ DPRINTK("id 0x%x SWNCQ: qc_active 0x%X "
+ "dhfis 0x%X dmafis 0x%X sactive 0x%X\n",
+ ap->print_id, pp->qc_active, pp->dhfis_bits,
+ pp->dmafis_bits, readl(pp->sactive_block));
+ rc = nv_swncq_sdbfis(ap);
+ if (rc < 0)
+ goto irq_error;
+ }
+
+ if (fis & NV_SWNCQ_IRQ_DHREGFIS) {
+ /* The interrupt indicates the new command
+ * was transmitted correctly to the drive.
+ */
+ pp->dhfis_bits |= (0x1 << pp->last_issue_tag);
+ pp->ncq_flags |= ncq_saw_d2h;
+ if (pp->ncq_flags & (ncq_saw_sdb | ncq_saw_backout)) {
+ ata_ehi_push_desc(ehi, "illegal fis transaction");
+ ehi->err_mask |= AC_ERR_HSM;
+ ehi->action |= ATA_EH_HARDRESET;
+ goto irq_error;
+ }
+
+ if (!(fis & NV_SWNCQ_IRQ_DMASETUP) &&
+ !(pp->ncq_flags & ncq_saw_dmas)) {
+ ata_stat = ap->ops->check_status(ap);
+ if (ata_stat & ATA_BUSY)
+ goto irq_exit;
+
+ if (pp->defer_queue.defer_bits) {
+ DPRINTK("send next command\n");
+ qc = nv_swncq_qc_from_dq(ap);
+ nv_swncq_issue_atacmd(ap, qc);
+ }
+ }
+ }
+
+ if (fis & NV_SWNCQ_IRQ_DMASETUP) {
+ /* program the dma controller with appropriate PRD buffers
+ * and start the DMA transfer for requested command.
+ */
+ pp->dmafis_bits |= (0x1 << nv_swncq_tag(ap));
+ pp->ncq_flags |= ncq_saw_dmas;
+ rc = nv_swncq_dmafis(ap);
+ }
+
+irq_exit:
+ return;
+irq_error:
+ ata_ehi_push_desc(ehi, "fis:0x%x", fis);
+ ata_port_freeze(ap);
+ return;
+}
+
+static irqreturn_t nv_swncq_interrupt(int irq, void *dev_instance)
+{
+ struct ata_host *host = dev_instance;
+ unsigned int i;
+ unsigned int handled = 0;
+ unsigned long flags;
+ u32 irq_stat;
+
+ spin_lock_irqsave(&host->lock, flags);
+
+ irq_stat = readl(host->iomap[NV_MMIO_BAR] + NV_INT_STATUS_MCP55);
+
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap = host->ports[i];
+
+ if (ap && !(ap->flags & ATA_FLAG_DISABLED)) {
+ if (ap->link.sactive) {
+ nv_swncq_host_interrupt(ap, (u16)irq_stat);
+ handled = 1;
+ } else {
+ if (irq_stat) /* reserve Hotplug */
+ nv_swncq_irq_clear(ap, 0xfff0);
+
+ handled += nv_host_intr(ap, (u8)irq_stat);
+ }
+ }
+ irq_stat >>= NV_INT_PORT_SHIFT_MCP55;
+ }
+
+ spin_unlock_irqrestore(&host->lock, flags);
+
+ return IRQ_RETVAL(handled);
+}
+
static int nv_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version = 0;
@@ -1551,7 +2378,7 @@ static int nv_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
return rc;
/* determine type and allocate host */
- if (type >= CK804 && adma_enabled) {
+ if (type == CK804 && adma_enabled) {
dev_printk(KERN_NOTICE, &pdev->dev, "Using ADMA mode\n");
type = ADMA;
}
@@ -1597,6 +2424,9 @@ static int nv_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
rc = nv_adma_host_init(host);
if (rc)
return rc;
+ } else if (type == SWNCQ && swncq_enabled) {
+ dev_printk(KERN_NOTICE, &pdev->dev, "Using SWNCQ mode\n");
+ nv_swncq_host_init(host);
}
pci_set_master(pdev);
@@ -1696,3 +2526,6 @@ module_init(nv_init);
module_exit(nv_exit);
module_param_named(adma, adma_enabled, bool, 0444);
MODULE_PARM_DESC(adma, "Enable use of ADMA (Default: true)");
+module_param_named(swncq, swncq_enabled, bool, 0444);
+MODULE_PARM_DESC(swncq, "Enable use of SWNCQ (Default: false)");
+
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2007-07-20 15:00 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2007-07-20 15:00 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Bug fixes, and 1/4 of Tejun's port multiplier work.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/ahci.c | 255 +++++++++++++++++++++++++------------------
drivers/ata/libata-core.c | 79 +++++++++-----
drivers/ata/libata-eh.c | 204 ++++++++++++++++++++++++++++++++---
drivers/ata/libata-scsi.c | 63 ++++++++---
drivers/ata/libata-sff.c | 4 +-
drivers/ata/libata.h | 3 +-
drivers/ata/pata_platform.c | 5 +-
drivers/ata/pata_scc.c | 29 +++--
drivers/ata/sata_inic162x.c | 16 ++--
drivers/ata/sata_mv.c | 203 ++++++++++++++++++++--------------
drivers/ata/sata_nv.c | 38 ++++---
drivers/ata/sata_promise.c | 25 +++--
drivers/ata/sata_qstor.c | 18 ++--
drivers/ata/sata_sil.c | 25 +++--
drivers/ata/sata_sil24.c | 139 ++++++++++++++++-------
drivers/ata/sata_sis.c | 22 ++--
drivers/ata/sata_svw.c | 13 +-
drivers/ata/sata_uli.c | 16 ++-
drivers/ata/sata_via.c | 27 +++--
drivers/ata/sata_vsc.c | 13 +-
include/linux/libata.h | 35 +++---
21 files changed, 816 insertions(+), 416 deletions(-)
Akira Iguchi (1):
pata_scc.c: small fixes (Workaround for errata A308)
Alexey Dobriyan (1):
ahci.c: fix CONFIG_PM=n compilation
Dave Jones (1):
Correct comment in libata-sff.c
Jeff Garzik (2):
[libata] sata_mv: Micro-optimization and cleanups
[libata] sata_mv: minor cleanups
Magnus Damm (1):
pata_platform: Fix NULL pointer dereference
Petr Vandrovec (1):
[libata] Fix reported task file values in sense data
Tejun Heo (21):
libata: add ST9160821AS 3.CLF to NONCQ blacklist
libata: add @is_cmd to ata_tf_to_fis()
ahci: use deadline instead of fixed timeout for 1st FIS for SRST
ahci: separate out ahci_kick_engine()
ahci: separate out ahci_exec_polled_cmd()
ahci: separate out ahci_do_softreset()
sata_sil24: replace sil24_update_tf() with sil24_read_tf()
sata_sil24: separate out sil24_exec_polled_cmd()
sata_sil24: separate out sil24_do_softreset()
libata: improve EH report formatting
libata: implement AC_ERR_NCQ
libata: make ->scr_read/write callbacks return error code
ahci: make NO_NCQ handling more consistent
ahci: implement SCR_NOTIFICATION r/w
libata: improve SATA PHY speed down logic
libata: quickly trigger SATA SPD down after debouncing failed
libata: improve SCSI scan failure handling
libata: reorganize ata_ehi_hotplugged()
libata: clear HOTPLUG flag after a reset
libata: schedule probing after SError access failure during autopsy
libata: implement EH fast drain
su henry (1):
The SATA controller device ID is different according to
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 11e4eb9..06f212f 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -99,6 +99,7 @@ enum {
HOST_CAP_SSC = (1 << 14), /* Slumber capable */
HOST_CAP_CLO = (1 << 24), /* Command List Override support */
HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */
+ HOST_CAP_SNTF = (1 << 29), /* SNotification register */
HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */
HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */
@@ -113,11 +114,11 @@ enum {
PORT_TFDATA = 0x20, /* taskfile data */
PORT_SIG = 0x24, /* device TF signature */
PORT_CMD_ISSUE = 0x38, /* command issue */
- PORT_SCR = 0x28, /* SATA phy register block */
PORT_SCR_STAT = 0x28, /* SATA phy register: SStatus */
PORT_SCR_CTL = 0x2c, /* SATA phy register: SControl */
PORT_SCR_ERR = 0x30, /* SATA phy register: SError */
PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */
+ PORT_SCR_NTF = 0x3c, /* SATA phy register: SNotification */
/* PORT_IRQ_{STAT,MASK} bits */
PORT_IRQ_COLD_PRES = (1 << 31), /* cold presence detect */
@@ -216,8 +217,8 @@ struct ahci_port_priv {
unsigned int ncq_saw_sdb:1;
};
-static u32 ahci_scr_read (struct ata_port *ap, unsigned int sc_reg);
-static void ahci_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
+static int ahci_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val);
+static int ahci_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val);
static int ahci_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc);
static void ahci_irq_clear(struct ata_port *ap);
@@ -417,7 +418,10 @@ static const struct pci_device_id ahci_pci_tbl[] = {
/* ATI */
{ PCI_VDEVICE(ATI, 0x4380), board_ahci_sb600 }, /* ATI SB600 */
- { PCI_VDEVICE(ATI, 0x4390), board_ahci_sb600 }, /* ATI SB700 */
+ { PCI_VDEVICE(ATI, 0x4390), board_ahci_sb600 }, /* ATI SB700 IDE */
+ { PCI_VDEVICE(ATI, 0x4391), board_ahci_sb600 }, /* ATI SB700 AHCI */
+ { PCI_VDEVICE(ATI, 0x4392), board_ahci_sb600 }, /* ATI SB700 nraid5 */
+ { PCI_VDEVICE(ATI, 0x4393), board_ahci_sb600 }, /* ATI SB700 raid5 */
/* VIA */
{ PCI_VDEVICE(VIA, 0x3349), board_ahci_vt8251 }, /* VIA VT8251 */
@@ -545,13 +549,19 @@ static void ahci_save_initial_config(struct pci_dev *pdev,
hpriv->saved_cap = cap = readl(mmio + HOST_CAP);
hpriv->saved_port_map = port_map = readl(mmio + HOST_PORTS_IMPL);
- /* some chips lie about 64bit support */
+ /* some chips have errata preventing 64bit use */
if ((cap & HOST_CAP_64) && (pi->flags & AHCI_FLAG_32BIT_ONLY)) {
dev_printk(KERN_INFO, &pdev->dev,
"controller can't do 64bit DMA, forcing 32bit\n");
cap &= ~HOST_CAP_64;
}
+ if ((cap & HOST_CAP_NCQ) && (pi->flags & AHCI_FLAG_NO_NCQ)) {
+ dev_printk(KERN_INFO, &pdev->dev,
+ "controller can't do NCQ, turning off CAP_NCQ\n");
+ cap &= ~HOST_CAP_NCQ;
+ }
+
/* fixup zero port_map */
if (!port_map) {
port_map = (1 << ahci_nr_ports(cap)) - 1;
@@ -625,38 +635,45 @@ static void ahci_restore_initial_config(struct ata_host *host)
(void) readl(mmio + HOST_PORTS_IMPL); /* flush */
}
-static u32 ahci_scr_read (struct ata_port *ap, unsigned int sc_reg_in)
+static unsigned ahci_scr_offset(struct ata_port *ap, unsigned int sc_reg)
{
- unsigned int sc_reg;
-
- switch (sc_reg_in) {
- case SCR_STATUS: sc_reg = 0; break;
- case SCR_CONTROL: sc_reg = 1; break;
- case SCR_ERROR: sc_reg = 2; break;
- case SCR_ACTIVE: sc_reg = 3; break;
- default:
- return 0xffffffffU;
- }
+ static const int offset[] = {
+ [SCR_STATUS] = PORT_SCR_STAT,
+ [SCR_CONTROL] = PORT_SCR_CTL,
+ [SCR_ERROR] = PORT_SCR_ERR,
+ [SCR_ACTIVE] = PORT_SCR_ACT,
+ [SCR_NOTIFICATION] = PORT_SCR_NTF,
+ };
+ struct ahci_host_priv *hpriv = ap->host->private_data;
- return readl(ap->ioaddr.scr_addr + (sc_reg * 4));
+ if (sc_reg < ARRAY_SIZE(offset) &&
+ (sc_reg != SCR_NOTIFICATION || (hpriv->cap & HOST_CAP_SNTF)))
+ return offset[sc_reg];
+ return 0;
}
-
-static void ahci_scr_write (struct ata_port *ap, unsigned int sc_reg_in,
- u32 val)
+static int ahci_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val)
{
- unsigned int sc_reg;
-
- switch (sc_reg_in) {
- case SCR_STATUS: sc_reg = 0; break;
- case SCR_CONTROL: sc_reg = 1; break;
- case SCR_ERROR: sc_reg = 2; break;
- case SCR_ACTIVE: sc_reg = 3; break;
- default:
- return;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ int offset = ahci_scr_offset(ap, sc_reg);
+
+ if (offset) {
+ *val = readl(port_mmio + offset);
+ return 0;
}
+ return -EINVAL;
+}
- writel(val, ap->ioaddr.scr_addr + (sc_reg * 4));
+static int ahci_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+ int offset = ahci_scr_offset(ap, sc_reg);
+
+ if (offset) {
+ writel(val, port_mmio + offset);
+ return 0;
+ }
+ return -EINVAL;
}
static void ahci_start_engine(struct ata_port *ap)
@@ -948,37 +965,87 @@ static void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag,
pp->cmd_slot[tag].tbl_addr_hi = cpu_to_le32((cmd_tbl_dma >> 16) >> 16);
}
-static int ahci_clo(struct ata_port *ap)
+static int ahci_kick_engine(struct ata_port *ap, int force_restart)
{
void __iomem *port_mmio = ap->ioaddr.cmd_addr;
struct ahci_host_priv *hpriv = ap->host->private_data;
u32 tmp;
+ int busy, rc;
+
+ /* do we need to kick the port? */
+ busy = ahci_check_status(ap) & (ATA_BUSY | ATA_DRQ);
+ if (!busy && !force_restart)
+ return 0;
+
+ /* stop engine */
+ rc = ahci_stop_engine(ap);
+ if (rc)
+ goto out_restart;
- if (!(hpriv->cap & HOST_CAP_CLO))
- return -EOPNOTSUPP;
+ /* need to do CLO? */
+ if (!busy) {
+ rc = 0;
+ goto out_restart;
+ }
+ if (!(hpriv->cap & HOST_CAP_CLO)) {
+ rc = -EOPNOTSUPP;
+ goto out_restart;
+ }
+
+ /* perform CLO */
tmp = readl(port_mmio + PORT_CMD);
tmp |= PORT_CMD_CLO;
writel(tmp, port_mmio + PORT_CMD);
+ rc = 0;
tmp = ata_wait_register(port_mmio + PORT_CMD,
PORT_CMD_CLO, PORT_CMD_CLO, 1, 500);
if (tmp & PORT_CMD_CLO)
- return -EIO;
+ rc = -EIO;
- return 0;
+ /* restart engine */
+ out_restart:
+ ahci_start_engine(ap);
+ return rc;
}
-static int ahci_softreset(struct ata_port *ap, unsigned int *class,
- unsigned long deadline)
+static int ahci_exec_polled_cmd(struct ata_port *ap, int pmp,
+ struct ata_taskfile *tf, int is_cmd, u16 flags,
+ unsigned long timeout_msec)
{
+ const u32 cmd_fis_len = 5; /* five dwords */
struct ahci_port_priv *pp = ap->private_data;
void __iomem *port_mmio = ahci_port_base(ap);
- const u32 cmd_fis_len = 5; /* five dwords */
+ u8 *fis = pp->cmd_tbl;
+ u32 tmp;
+
+ /* prep the command */
+ ata_tf_to_fis(tf, pmp, is_cmd, fis);
+ ahci_fill_cmd_slot(pp, 0, cmd_fis_len | flags | (pmp << 12));
+
+ /* issue & wait */
+ writel(1, port_mmio + PORT_CMD_ISSUE);
+
+ if (timeout_msec) {
+ tmp = ata_wait_register(port_mmio + PORT_CMD_ISSUE, 0x1, 0x1,
+ 1, timeout_msec);
+ if (tmp & 0x1) {
+ ahci_kick_engine(ap, 1);
+ return -EBUSY;
+ }
+ } else
+ readl(port_mmio + PORT_CMD_ISSUE); /* flush */
+
+ return 0;
+}
+
+static int ahci_do_softreset(struct ata_port *ap, unsigned int *class,
+ int pmp, unsigned long deadline)
+{
const char *reason = NULL;
+ unsigned long now, msecs;
struct ata_taskfile tf;
- u32 tmp;
- u8 *fis;
int rc;
DPRINTK("ENTER\n");
@@ -990,43 +1057,22 @@ static int ahci_softreset(struct ata_port *ap, unsigned int *class,
}
/* prepare for SRST (AHCI-1.1 10.4.1) */
- rc = ahci_stop_engine(ap);
- if (rc) {
- reason = "failed to stop engine";
- goto fail_restart;
- }
-
- /* check BUSY/DRQ, perform Command List Override if necessary */
- if (ahci_check_status(ap) & (ATA_BUSY | ATA_DRQ)) {
- rc = ahci_clo(ap);
-
- if (rc == -EOPNOTSUPP) {
- reason = "port busy but CLO unavailable";
- goto fail_restart;
- } else if (rc) {
- reason = "port busy but CLO failed";
- goto fail_restart;
- }
- }
-
- /* restart engine */
- ahci_start_engine(ap);
+ rc = ahci_kick_engine(ap, 1);
+ if (rc)
+ ata_port_printk(ap, KERN_WARNING,
+ "failed to reset engine (errno=%d)", rc);
ata_tf_init(ap->device, &tf);
- fis = pp->cmd_tbl;
/* issue the first D2H Register FIS */
- ahci_fill_cmd_slot(pp, 0,
- cmd_fis_len | AHCI_CMD_RESET | AHCI_CMD_CLR_BUSY);
+ msecs = 0;
+ now = jiffies;
+ if (time_after(now, deadline))
+ msecs = jiffies_to_msecs(deadline - now);
tf.ctl |= ATA_SRST;
- ata_tf_to_fis(&tf, fis, 0);
- fis[1] &= ~(1 << 7); /* turn off Command FIS bit */
-
- writel(1, port_mmio + PORT_CMD_ISSUE);
-
- tmp = ata_wait_register(port_mmio + PORT_CMD_ISSUE, 0x1, 0x1, 1, 500);
- if (tmp & 0x1) {
+ if (ahci_exec_polled_cmd(ap, pmp, &tf, 0,
+ AHCI_CMD_RESET | AHCI_CMD_CLR_BUSY, msecs)) {
rc = -EIO;
reason = "1st FIS failed";
goto fail;
@@ -1036,14 +1082,8 @@ static int ahci_softreset(struct ata_port *ap, unsigned int *class,
msleep(1);
/* issue the second D2H Register FIS */
- ahci_fill_cmd_slot(pp, 0, cmd_fis_len);
-
tf.ctl &= ~ATA_SRST;
- ata_tf_to_fis(&tf, fis, 0);
- fis[1] &= ~(1 << 7); /* turn off Command FIS bit */
-
- writel(1, port_mmio + PORT_CMD_ISSUE);
- readl(port_mmio + PORT_CMD_ISSUE); /* flush */
+ ahci_exec_polled_cmd(ap, pmp, &tf, 0, 0, 0);
/* spec mandates ">= 2ms" before checking status.
* We wait 150ms, because that was the magic delay used for
@@ -1066,13 +1106,17 @@ static int ahci_softreset(struct ata_port *ap, unsigned int *class,
DPRINTK("EXIT, class=%u\n", *class);
return 0;
- fail_restart:
- ahci_start_engine(ap);
fail:
ata_port_printk(ap, KERN_ERR, "softreset failed (%s)\n", reason);
return rc;
}
+static int ahci_softreset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
+{
+ return ahci_do_softreset(ap, class, 0, deadline);
+}
+
static int ahci_hardreset(struct ata_port *ap, unsigned int *class,
unsigned long deadline)
{
@@ -1088,7 +1132,7 @@ static int ahci_hardreset(struct ata_port *ap, unsigned int *class,
/* clear D2H reception area to properly wait for D2H FIS */
ata_tf_init(ap->device, &tf);
tf.command = 0x80;
- ata_tf_to_fis(&tf, d2h_fis, 0);
+ ata_tf_to_fis(&tf, 0, 0, d2h_fis);
rc = sata_std_hardreset(ap, class, deadline);
@@ -1106,6 +1150,7 @@ static int ahci_hardreset(struct ata_port *ap, unsigned int *class,
static int ahci_vt8251_hardreset(struct ata_port *ap, unsigned int *class,
unsigned long deadline)
{
+ u32 serror;
int rc;
DPRINTK("ENTER\n");
@@ -1116,7 +1161,8 @@ static int ahci_vt8251_hardreset(struct ata_port *ap, unsigned int *class,
deadline);
/* vt8251 needs SError cleared for the port to operate */
- ahci_scr_write(ap, SCR_ERROR, ahci_scr_read(ap, SCR_ERROR));
+ ahci_scr_read(ap, SCR_ERROR, &serror);
+ ahci_scr_write(ap, SCR_ERROR, serror);
ahci_start_engine(ap);
@@ -1205,7 +1251,7 @@ static void ahci_qc_prep(struct ata_queued_cmd *qc)
*/
cmd_tbl = pp->cmd_tbl + qc->tag * AHCI_CMD_TBL_SZ;
- ata_tf_to_fis(&qc->tf, cmd_tbl, 0);
+ ata_tf_to_fis(&qc->tf, 0, 1, cmd_tbl);
if (is_atapi) {
memset(cmd_tbl + AHCI_CMD_TBL_CDB, 0, 32);
memcpy(cmd_tbl + AHCI_CMD_TBL_CDB, qc->cdb, qc->dev->cdb_len);
@@ -1238,7 +1284,7 @@ static void ahci_error_intr(struct ata_port *ap, u32 irq_stat)
ata_ehi_clear_desc(ehi);
/* AHCI needs SError cleared; otherwise, it might lock up */
- serror = ahci_scr_read(ap, SCR_ERROR);
+ ahci_scr_read(ap, SCR_ERROR, &serror);
ahci_scr_write(ap, SCR_ERROR, serror);
/* analyze @irq_stat */
@@ -1262,12 +1308,12 @@ static void ahci_error_intr(struct ata_port *ap, u32 irq_stat)
if (irq_stat & PORT_IRQ_IF_ERR) {
err_mask |= AC_ERR_ATA_BUS;
action |= ATA_EH_SOFTRESET;
- ata_ehi_push_desc(ehi, ", interface fatal error");
+ ata_ehi_push_desc(ehi, "interface fatal error");
}
if (irq_stat & (PORT_IRQ_CONNECT | PORT_IRQ_PHYRDY)) {
ata_ehi_hotplugged(ehi);
- ata_ehi_push_desc(ehi, ", %s", irq_stat & PORT_IRQ_CONNECT ?
+ ata_ehi_push_desc(ehi, "%s", irq_stat & PORT_IRQ_CONNECT ?
"connection status changed" : "PHY RDY changed");
}
@@ -1276,7 +1322,7 @@ static void ahci_error_intr(struct ata_port *ap, u32 irq_stat)
err_mask |= AC_ERR_HSM;
action |= ATA_EH_SOFTRESET;
- ata_ehi_push_desc(ehi, ", unknown FIS %08x %08x %08x %08x",
+ ata_ehi_push_desc(ehi, "unknown FIS %08x %08x %08x %08x",
unk[0], unk[1], unk[2], unk[3]);
}
@@ -1512,11 +1558,17 @@ static void ahci_post_internal_cmd(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
- if (qc->flags & ATA_QCFLAG_FAILED) {
- /* make DMA engine forget about the failed command */
- ahci_stop_engine(ap);
- ahci_start_engine(ap);
- }
+ /* make DMA engine forget about the failed command */
+ if (qc->flags & ATA_QCFLAG_FAILED)
+ ahci_kick_engine(ap, 1);
+}
+
+static int ahci_port_resume(struct ata_port *ap)
+{
+ ahci_power_up(ap);
+ ahci_start_port(ap);
+
+ return 0;
}
#ifdef CONFIG_PM
@@ -1536,14 +1588,6 @@ static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg)
return rc;
}
-static int ahci_port_resume(struct ata_port *ap)
-{
- ahci_power_up(ap);
- ahci_start_port(ap);
-
- return 0;
-}
-
static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
{
struct ata_host *host = dev_get_drvdata(&pdev->dev);
@@ -1734,12 +1778,13 @@ static void ahci_print_info(struct ata_host *host)
dev_printk(KERN_INFO, &pdev->dev,
"flags: "
- "%s%s%s%s%s%s"
- "%s%s%s%s%s%s%s\n"
+ "%s%s%s%s%s%s%s"
+ "%s%s%s%s%s%s%s\n"
,
cap & (1 << 31) ? "64bit " : "",
cap & (1 << 30) ? "ncq " : "",
+ cap & (1 << 29) ? "sntf " : "",
cap & (1 << 28) ? "ilck " : "",
cap & (1 << 27) ? "stag " : "",
cap & (1 << 26) ? "pm " : "",
@@ -1794,7 +1839,7 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
ahci_save_initial_config(pdev, &pi, hpriv);
/* prepare host */
- if (!(pi.flags & AHCI_FLAG_NO_NCQ) && (hpriv->cap & HOST_CAP_NCQ))
+ if (hpriv->cap & HOST_CAP_NCQ)
pi.flags |= ATA_FLAG_NCQ;
host = ata_host_alloc_pinfo(&pdev->dev, ppi, fls(hpriv->port_map));
@@ -1808,10 +1853,8 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
void __iomem *port_mmio = ahci_port_base(ap);
/* standard SATA port setup */
- if (hpriv->port_map & (1 << i)) {
+ if (hpriv->port_map & (1 << i))
ap->ioaddr.cmd_addr = port_mmio;
- ap->ioaddr.scr_addr = port_mmio + PORT_SCR;
- }
/* disabled/not-implemented port */
else
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 88e2dd0..6001aae 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -111,8 +111,9 @@ MODULE_VERSION(DRV_VERSION);
/**
* ata_tf_to_fis - Convert ATA taskfile to SATA FIS structure
* @tf: Taskfile to convert
- * @fis: Buffer into which data will output
* @pmp: Port multiplier port
+ * @is_cmd: This FIS is for command
+ * @fis: Buffer into which data will output
*
* Converts a standard ATA taskfile to a Serial ATA
* FIS structure (Register - Host to Device).
@@ -120,12 +121,13 @@ MODULE_VERSION(DRV_VERSION);
* LOCKING:
* Inherited from caller.
*/
-
-void ata_tf_to_fis(const struct ata_taskfile *tf, u8 *fis, u8 pmp)
+void ata_tf_to_fis(const struct ata_taskfile *tf, u8 pmp, int is_cmd, u8 *fis)
{
- fis[0] = 0x27; /* Register - Host to Device FIS */
- fis[1] = (pmp & 0xf) | (1 << 7); /* Port multiplier number,
- bit 7 indicates Command FIS */
+ fis[0] = 0x27; /* Register - Host to Device FIS */
+ fis[1] = pmp & 0xf; /* Port multiplier number*/
+ if (is_cmd)
+ fis[1] |= (1 << 7); /* bit 7 indicates Command FIS */
+
fis[2] = tf->command;
fis[3] = tf->feature;
@@ -2387,21 +2389,35 @@ int sata_down_spd_limit(struct ata_port *ap)
u32 sstatus, spd, mask;
int rc, highbit;
+ if (!sata_scr_valid(ap))
+ return -EOPNOTSUPP;
+
+ /* If SCR can be read, use it to determine the current SPD.
+ * If not, use cached value in ap->sata_spd.
+ */
rc = sata_scr_read(ap, SCR_STATUS, &sstatus);
- if (rc)
- return rc;
+ if (rc == 0)
+ spd = (sstatus >> 4) & 0xf;
+ else
+ spd = ap->sata_spd;
mask = ap->sata_spd_limit;
if (mask <= 1)
return -EINVAL;
+
+ /* unconditionally mask off the highest bit */
highbit = fls(mask) - 1;
mask &= ~(1 << highbit);
- spd = (sstatus >> 4) & 0xf;
- if (spd <= 1)
- return -EINVAL;
- spd--;
- mask &= (1 << spd) - 1;
+ /* Mask off all speeds higher than or equal to the current
+ * one. Force 1.5Gbps if current SPD is not available.
+ */
+ if (spd > 1)
+ mask &= (1 << (spd - 1)) - 1;
+ else
+ mask &= 1;
+
+ /* were we already at the bottom? */
if (!mask)
return -EINVAL;
@@ -3251,9 +3267,11 @@ int sata_phy_debounce(struct ata_port *ap, const unsigned long *params,
last = cur;
last_jiffies = jiffies;
- /* check deadline */
+ /* Check deadline. If debouncing failed, return
+ * -EPIPE to tell upper layer to lower link speed.
+ */
if (time_after(jiffies, deadline))
- return -EBUSY;
+ return -EPIPE;
}
}
@@ -3769,6 +3787,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
{ "Hitachi HTS541616J9SA00", "SB4OC70P", ATA_HORKAGE_NONCQ, },
{ "WDC WD740ADFD-00NLR1", NULL, ATA_HORKAGE_NONCQ, },
{ "FUJITSU MHV2080BH", "00840028", ATA_HORKAGE_NONCQ, },
+ { "ST9160821AS", "3.CLF", ATA_HORKAGE_NONCQ, },
/* Devices with NCQ limits */
@@ -5729,10 +5748,8 @@ int sata_scr_valid(struct ata_port *ap)
*/
int sata_scr_read(struct ata_port *ap, int reg, u32 *val)
{
- if (sata_scr_valid(ap)) {
- *val = ap->ops->scr_read(ap, reg);
- return 0;
- }
+ if (sata_scr_valid(ap))
+ return ap->ops->scr_read(ap, reg, val);
return -EOPNOTSUPP;
}
@@ -5754,10 +5771,8 @@ int sata_scr_read(struct ata_port *ap, int reg, u32 *val)
*/
int sata_scr_write(struct ata_port *ap, int reg, u32 val)
{
- if (sata_scr_valid(ap)) {
- ap->ops->scr_write(ap, reg, val);
- return 0;
- }
+ if (sata_scr_valid(ap))
+ return ap->ops->scr_write(ap, reg, val);
return -EOPNOTSUPP;
}
@@ -5778,10 +5793,13 @@ int sata_scr_write(struct ata_port *ap, int reg, u32 val)
*/
int sata_scr_write_flush(struct ata_port *ap, int reg, u32 val)
{
+ int rc;
+
if (sata_scr_valid(ap)) {
- ap->ops->scr_write(ap, reg, val);
- ap->ops->scr_read(ap, reg);
- return 0;
+ rc = ap->ops->scr_write(ap, reg, val);
+ if (rc == 0)
+ rc = ap->ops->scr_read(ap, reg, &val);
+ return rc;
}
return -EOPNOTSUPP;
}
@@ -5993,6 +6011,7 @@ void ata_dev_init(struct ata_device *dev)
/* SATA spd limit is bound to the first device */
ap->sata_spd_limit = ap->hw_sata_spd_limit;
+ ap->sata_spd = 0;
/* High bits of dev->flags are used to record warm plug
* requests which occur asynchronously. Synchronize using
@@ -6058,6 +6077,9 @@ struct ata_port *ata_port_alloc(struct ata_host *host)
INIT_WORK(&ap->scsi_rescan_task, ata_scsi_dev_rescan);
INIT_LIST_HEAD(&ap->eh_done_q);
init_waitqueue_head(&ap->eh_wait_q);
+ init_timer_deferrable(&ap->fastdrain_timer);
+ ap->fastdrain_timer.function = ata_eh_fastdrain_timerfn;
+ ap->fastdrain_timer.data = (unsigned long)ap;
ap->cbl = ATA_CBL_NONE;
@@ -6434,7 +6456,7 @@ int ata_host_register(struct ata_host *host, struct scsi_host_template *sht)
for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap = host->ports[i];
- ata_scsi_scan_host(ap);
+ ata_scsi_scan_host(ap, 1);
}
return 0;
@@ -6942,6 +6964,9 @@ EXPORT_SYMBOL_GPL(ata_pci_default_filter);
EXPORT_SYMBOL_GPL(ata_pci_clear_simplex);
#endif /* CONFIG_PCI */
+EXPORT_SYMBOL_GPL(__ata_ehi_push_desc);
+EXPORT_SYMBOL_GPL(ata_ehi_push_desc);
+EXPORT_SYMBOL_GPL(ata_ehi_clear_desc);
EXPORT_SYMBOL_GPL(ata_eng_timeout);
EXPORT_SYMBOL_GPL(ata_port_schedule_eh);
EXPORT_SYMBOL_GPL(ata_port_abort);
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 9aa62a0..ac6ceed 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -56,6 +56,7 @@ enum {
*/
enum {
ATA_EH_PRERESET_TIMEOUT = 10 * HZ,
+ ATA_EH_FASTDRAIN_INTERVAL = 3 * HZ,
};
/* The following table determines how we sequence resets. Each entry
@@ -85,6 +86,71 @@ static void ata_eh_handle_port_resume(struct ata_port *ap)
{ }
#endif /* CONFIG_PM */
+static void __ata_ehi_pushv_desc(struct ata_eh_info *ehi, const char *fmt,
+ va_list args)
+{
+ ehi->desc_len += vscnprintf(ehi->desc + ehi->desc_len,
+ ATA_EH_DESC_LEN - ehi->desc_len,
+ fmt, args);
+}
+
+/**
+ * __ata_ehi_push_desc - push error description without adding separator
+ * @ehi: target EHI
+ * @fmt: printf format string
+ *
+ * Format string according to @fmt and append it to @ehi->desc.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void __ata_ehi_push_desc(struct ata_eh_info *ehi, const char *fmt, ...)
+{
+ va_list args;
+
+ va_start(args, fmt);
+ __ata_ehi_pushv_desc(ehi, fmt, args);
+ va_end(args);
+}
+
+/**
+ * ata_ehi_push_desc - push error description with separator
+ * @ehi: target EHI
+ * @fmt: printf format string
+ *
+ * Format string according to @fmt and append it to @ehi->desc.
+ * If @ehi->desc is not empty, ", " is added in-between.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void ata_ehi_push_desc(struct ata_eh_info *ehi, const char *fmt, ...)
+{
+ va_list args;
+
+ if (ehi->desc_len)
+ __ata_ehi_push_desc(ehi, ", ");
+
+ va_start(args, fmt);
+ __ata_ehi_pushv_desc(ehi, fmt, args);
+ va_end(args);
+}
+
+/**
+ * ata_ehi_clear_desc - clean error description
+ * @ehi: target EHI
+ *
+ * Clear @ehi->desc.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void ata_ehi_clear_desc(struct ata_eh_info *ehi)
+{
+ ehi->desc[0] = '\0';
+ ehi->desc_len = 0;
+}
+
static void ata_ering_record(struct ata_ering *ering, int is_io,
unsigned int err_mask)
{
@@ -296,6 +362,9 @@ void ata_scsi_error(struct Scsi_Host *host)
repeat:
/* invoke error handler */
if (ap->ops->error_handler) {
+ /* kill fast drain timer */
+ del_timer_sync(&ap->fastdrain_timer);
+
/* process port resume request */
ata_eh_handle_port_resume(ap);
@@ -511,6 +580,94 @@ void ata_eng_timeout(struct ata_port *ap)
DPRINTK("EXIT\n");
}
+static int ata_eh_nr_in_flight(struct ata_port *ap)
+{
+ unsigned int tag;
+ int nr = 0;
+
+ /* count only non-internal commands */
+ for (tag = 0; tag < ATA_MAX_QUEUE - 1; tag++)
+ if (ata_qc_from_tag(ap, tag))
+ nr++;
+
+ return nr;
+}
+
+void ata_eh_fastdrain_timerfn(unsigned long arg)
+{
+ struct ata_port *ap = (void *)arg;
+ unsigned long flags;
+ int cnt;
+
+ spin_lock_irqsave(ap->lock, flags);
+
+ cnt = ata_eh_nr_in_flight(ap);
+
+ /* are we done? */
+ if (!cnt)
+ goto out_unlock;
+
+ if (cnt == ap->fastdrain_cnt) {
+ unsigned int tag;
+
+ /* No progress during the last interval, tag all
+ * in-flight qcs as timed out and freeze the port.
+ */
+ for (tag = 0; tag < ATA_MAX_QUEUE - 1; tag++) {
+ struct ata_queued_cmd *qc = ata_qc_from_tag(ap, tag);
+ if (qc)
+ qc->err_mask |= AC_ERR_TIMEOUT;
+ }
+
+ ata_port_freeze(ap);
+ } else {
+ /* some qcs have finished, give it another chance */
+ ap->fastdrain_cnt = cnt;
+ ap->fastdrain_timer.expires =
+ jiffies + ATA_EH_FASTDRAIN_INTERVAL;
+ add_timer(&ap->fastdrain_timer);
+ }
+
+ out_unlock:
+ spin_unlock_irqrestore(ap->lock, flags);
+}
+
+/**
+ * ata_eh_set_pending - set ATA_PFLAG_EH_PENDING and activate fast drain
+ * @ap: target ATA port
+ * @fastdrain: activate fast drain
+ *
+ * Set ATA_PFLAG_EH_PENDING and activate fast drain if @fastdrain
+ * is non-zero and EH wasn't pending before. Fast drain ensures
+ * that EH kicks in in timely manner.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+static void ata_eh_set_pending(struct ata_port *ap, int fastdrain)
+{
+ int cnt;
+
+ /* already scheduled? */
+ if (ap->pflags & ATA_PFLAG_EH_PENDING)
+ return;
+
+ ap->pflags |= ATA_PFLAG_EH_PENDING;
+
+ if (!fastdrain)
+ return;
+
+ /* do we have in-flight qcs? */
+ cnt = ata_eh_nr_in_flight(ap);
+ if (!cnt)
+ return;
+
+ /* activate fast drain */
+ ap->fastdrain_cnt = cnt;
+ ap->fastdrain_timer.expires = jiffies + ATA_EH_FASTDRAIN_INTERVAL;
+ add_timer(&ap->fastdrain_timer);
+}
+
/**
* ata_qc_schedule_eh - schedule qc for error handling
* @qc: command to schedule error handling for
@@ -528,7 +685,7 @@ void ata_qc_schedule_eh(struct ata_queued_cmd *qc)
WARN_ON(!ap->ops->error_handler);
qc->flags |= ATA_QCFLAG_FAILED;
- qc->ap->pflags |= ATA_PFLAG_EH_PENDING;
+ ata_eh_set_pending(ap, 1);
/* The following will fail if timeout has already expired.
* ata_scsi_error() takes care of such scmds on EH entry.
@@ -555,7 +712,7 @@ void ata_port_schedule_eh(struct ata_port *ap)
if (ap->pflags & ATA_PFLAG_INITIALIZING)
return;
- ap->pflags |= ATA_PFLAG_EH_PENDING;
+ ata_eh_set_pending(ap, 1);
scsi_schedule_eh(ap->scsi_host);
DPRINTK("port EH scheduled\n");
@@ -579,6 +736,9 @@ int ata_port_abort(struct ata_port *ap)
WARN_ON(!ap->ops->error_handler);
+ /* we're gonna abort all commands, no need for fast drain */
+ ata_eh_set_pending(ap, 0);
+
for (tag = 0; tag < ATA_MAX_QUEUE; tag++) {
struct ata_queued_cmd *qc = ata_qc_from_tag(ap, tag);
@@ -1130,7 +1290,7 @@ static void ata_eh_analyze_ncq_error(struct ata_port *ap)
/* we've got the perpetrator, condemn it */
qc = __ata_qc_from_tag(ap, tag);
memcpy(&qc->result_tf, &tf, sizeof(tf));
- qc->err_mask |= AC_ERR_DEV;
+ qc->err_mask |= AC_ERR_DEV | AC_ERR_NCQ;
ehc->i.err_mask &= ~AC_ERR_DEV;
}
@@ -1413,8 +1573,12 @@ static void ata_eh_autopsy(struct ata_port *ap)
if (rc == 0) {
ehc->i.serror |= serror;
ata_eh_analyze_serror(ap);
- } else if (rc != -EOPNOTSUPP)
+ } else if (rc != -EOPNOTSUPP) {
+ /* SError read failed, force hardreset and probing */
+ ata_ehi_schedule_probe(&ehc->i);
ehc->i.action |= ATA_EH_HARDRESET;
+ ehc->i.err_mask |= AC_ERR_OTHER;
+ }
/* analyze NCQ failure */
ata_eh_analyze_ncq_error(ap);
@@ -1524,14 +1688,14 @@ static void ata_eh_report(struct ata_port *ap)
ehc->i.err_mask, ap->sactive, ehc->i.serror,
ehc->i.action, frozen);
if (desc)
- ata_dev_printk(ehc->i.dev, KERN_ERR, "(%s)\n", desc);
+ ata_dev_printk(ehc->i.dev, KERN_ERR, "%s\n", desc);
} else {
ata_port_printk(ap, KERN_ERR, "exception Emask 0x%x "
"SAct 0x%x SErr 0x%x action 0x%x%s\n",
ehc->i.err_mask, ap->sactive, ehc->i.serror,
ehc->i.action, frozen);
if (desc)
- ata_port_printk(ap, KERN_ERR, "(%s)\n", desc);
+ ata_port_printk(ap, KERN_ERR, "%s\n", desc);
}
for (tag = 0; tag < ATA_MAX_QUEUE; tag++) {
@@ -1551,7 +1715,7 @@ static void ata_eh_report(struct ata_port *ap)
"cmd %02x/%02x:%02x:%02x:%02x:%02x/%02x:%02x:%02x:%02x:%02x/%02x "
"tag %d cdb 0x%x data %u %s\n "
"res %02x/%02x:%02x:%02x:%02x:%02x/%02x:%02x:%02x:%02x:%02x/%02x "
- "Emask 0x%x (%s)\n",
+ "Emask 0x%x (%s)%s\n",
cmd->command, cmd->feature, cmd->nsect,
cmd->lbal, cmd->lbam, cmd->lbah,
cmd->hob_feature, cmd->hob_nsect,
@@ -1562,7 +1726,8 @@ static void ata_eh_report(struct ata_port *ap)
res->lbal, res->lbam, res->lbah,
res->hob_feature, res->hob_nsect,
res->hob_lbal, res->hob_lbam, res->hob_lbah,
- res->device, qc->err_mask, ata_err_string(qc->err_mask));
+ res->device, qc->err_mask, ata_err_string(qc->err_mask),
+ qc->err_mask & AC_ERR_NCQ ? " <F>" : "");
}
}
@@ -1648,7 +1813,7 @@ static int ata_eh_reset(struct ata_port *ap, int classify,
} else
ata_port_printk(ap, KERN_ERR,
"prereset failed (errno=%d)\n", rc);
- return rc;
+ goto out;
}
}
@@ -1661,7 +1826,8 @@ static int ata_eh_reset(struct ata_port *ap, int classify,
/* prereset told us not to reset, bang classes and return */
for (i = 0; i < ATA_MAX_DEVICES; i++)
classes[i] = ATA_DEV_NONE;
- return 0;
+ rc = 0;
+ goto out;
}
/* did prereset() screw up? if so, fix up to avoid oopsing */
@@ -1697,7 +1863,8 @@ static int ata_eh_reset(struct ata_port *ap, int classify,
ata_port_printk(ap, KERN_ERR,
"follow-up softreset required "
"but no softreset avaliable\n");
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
ata_eh_about_to_do(ap, NULL, ATA_EH_RESET_MASK);
@@ -1707,7 +1874,8 @@ static int ata_eh_reset(struct ata_port *ap, int classify,
classes[0] == ATA_DEV_UNKNOWN) {
ata_port_printk(ap, KERN_ERR,
"classification failed\n");
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
}
@@ -1724,7 +1892,7 @@ static int ata_eh_reset(struct ata_port *ap, int classify,
schedule_timeout_uninterruptible(delta);
}
- if (reset == hardreset &&
+ if (rc == -EPIPE ||
try == ARRAY_SIZE(ata_eh_reset_timeouts) - 1)
sata_down_spd_limit(ap);
if (hardreset)
@@ -1733,12 +1901,18 @@ static int ata_eh_reset(struct ata_port *ap, int classify,
}
if (rc == 0) {
+ u32 sstatus;
+
/* After the reset, the device state is PIO 0 and the
* controller state is undefined. Record the mode.
*/
for (i = 0; i < ATA_MAX_DEVICES; i++)
ap->device[i].pio_mode = XFER_PIO_0;
+ /* record current link speed */
+ if (sata_scr_read(ap, SCR_STATUS, &sstatus) == 0)
+ ap->sata_spd = (sstatus >> 4) & 0xf;
+
if (postreset)
postreset(ap, classes);
@@ -1746,7 +1920,9 @@ static int ata_eh_reset(struct ata_port *ap, int classify,
ata_eh_done(ap, NULL, ehc->i.action & ATA_EH_RESET_MASK);
ehc->i.action |= ATA_EH_REVALIDATE;
}
-
+ out:
+ /* clear hotplug flag */
+ ehc->i.flags &= ~ATA_EHI_HOTPLUGGED;
return rc;
}
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index cfde22d..12ac0b5 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -2947,17 +2947,22 @@ int ata_scsi_add_hosts(struct ata_host *host, struct scsi_host_template *sht)
return rc;
}
-void ata_scsi_scan_host(struct ata_port *ap)
+void ata_scsi_scan_host(struct ata_port *ap, int sync)
{
+ int tries = 5;
+ struct ata_device *last_failed_dev = NULL;
+ struct ata_device *dev;
unsigned int i;
if (ap->flags & ATA_FLAG_DISABLED)
return;
+ repeat:
for (i = 0; i < ATA_MAX_DEVICES; i++) {
- struct ata_device *dev = &ap->device[i];
struct scsi_device *sdev;
+ dev = &ap->device[i];
+
if (!ata_dev_enabled(dev) || dev->sdev)
continue;
@@ -2967,6 +2972,45 @@ void ata_scsi_scan_host(struct ata_port *ap)
scsi_device_put(sdev);
}
}
+
+ /* If we scanned while EH was in progress or allocation
+ * failure occurred, scan would have failed silently. Check
+ * whether all devices are attached.
+ */
+ for (i = 0; i < ATA_MAX_DEVICES; i++) {
+ dev = &ap->device[i];
+ if (ata_dev_enabled(dev) && !dev->sdev)
+ break;
+ }
+ if (i == ATA_MAX_DEVICES)
+ return;
+
+ /* we're missing some SCSI devices */
+ if (sync) {
+ /* If caller requested synchrnous scan && we've made
+ * any progress, sleep briefly and repeat.
+ */
+ if (dev != last_failed_dev) {
+ msleep(100);
+ last_failed_dev = dev;
+ goto repeat;
+ }
+
+ /* We might be failing to detect boot device, give it
+ * a few more chances.
+ */
+ if (--tries) {
+ msleep(100);
+ goto repeat;
+ }
+
+ ata_port_printk(ap, KERN_ERR, "WARNING: synchronous SCSI scan "
+ "failed without making any progress,\n"
+ " switching to async\n");
+ }
+
+ queue_delayed_work(ata_aux_wq, &ap->hotplug_task,
+ round_jiffies_relative(HZ));
}
/**
@@ -3093,20 +3137,7 @@ void ata_scsi_hotplug(struct work_struct *work)
}
/* scan for new ones */
- ata_scsi_scan_host(ap);
-
- /* If we scanned while EH was in progress, scan would have
- * failed silently. Requeue if there are enabled but
- * unattached devices.
- */
- for (i = 0; i < ATA_MAX_DEVICES; i++) {
- struct ata_device *dev = &ap->device[i];
- if (ata_dev_enabled(dev) && !dev->sdev) {
- queue_delayed_work(ata_aux_wq, &ap->hotplug_task,
- round_jiffies_relative(HZ));
- break;
- }
- }
+ ata_scsi_scan_host(ap, 0);
DPRINTK("EXIT\n");
}
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index ca7d224..6c289c7 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -1,5 +1,5 @@
/*
- * libata-bmdma.c - helper library for PCI IDE BMDMA
+ * libata-sff.c - helper library for PCI IDE BMDMA
*
* Maintained by: Jeff Garzik <jgarzik@pobox.com>
* Please ALWAYS copy linux-ide@vger.kernel.org
@@ -211,6 +211,8 @@ void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
tf->hob_lbal = ioread8(ioaddr->lbal_addr);
tf->hob_lbam = ioread8(ioaddr->lbam_addr);
tf->hob_lbah = ioread8(ioaddr->lbah_addr);
+ iowrite8(tf->ctl, ioaddr->ctl_addr);
+ ap->last_ctl = tf->ctl;
}
}
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index ba17fc5..564cd23 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -112,7 +112,7 @@ static inline int ata_acpi_on_devcfg(struct ata_device *adev) { return 0; }
/* libata-scsi.c */
extern int ata_scsi_add_hosts(struct ata_host *host,
struct scsi_host_template *sht);
-extern void ata_scsi_scan_host(struct ata_port *ap);
+extern void ata_scsi_scan_host(struct ata_port *ap, int sync);
extern int ata_scsi_offline_dev(struct ata_device *dev);
extern void ata_scsi_hotplug(struct work_struct *work);
extern unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf,
@@ -151,6 +151,7 @@ extern int ata_bus_probe(struct ata_port *ap);
extern enum scsi_eh_timer_return ata_scsi_timed_out(struct scsi_cmnd *cmd);
extern void ata_scsi_error(struct Scsi_Host *host);
extern void ata_port_wait_eh(struct ata_port *ap);
+extern void ata_eh_fastdrain_timerfn(unsigned long arg);
extern void ata_qc_schedule_eh(struct ata_queued_cmd *qc);
/* libata-sff.c */
diff --git a/drivers/ata/pata_platform.c b/drivers/ata/pata_platform.c
index 79f841b..a909f79 100644
--- a/drivers/ata/pata_platform.c
+++ b/drivers/ata/pata_platform.c
@@ -213,8 +213,9 @@ static int __devinit pata_platform_probe(struct platform_device *pdev)
pata_platform_setup_port(&ap->ioaddr, pp_info);
/* activate */
- return ata_host_activate(host, platform_get_irq(pdev, 0), ata_interrupt,
- pp_info->irq_flags, &pata_platform_sht);
+ return ata_host_activate(host, platform_get_irq(pdev, 0),
+ ata_interrupt, pp_info ? pp_info->irq_flags
+ : 0, &pata_platform_sht);
}
/**
diff --git a/drivers/ata/pata_scc.c b/drivers/ata/pata_scc.c
index c55667e..36cdbd2 100644
--- a/drivers/ata/pata_scc.c
+++ b/drivers/ata/pata_scc.c
@@ -238,12 +238,6 @@ static void scc_set_dmamode (struct ata_port *ap, struct ata_device *adev)
else
offset = 0; /* 100MHz */
- /* errata A308 workaround: limit ATAPI UDMA mode to UDMA4 */
- if (adev->class == ATA_DEV_ATAPI && speed > XFER_UDMA_4) {
- printk(KERN_INFO "%s: limit ATAPI UDMA to UDMA4\n", DRV_NAME);
- speed = XFER_UDMA_4;
- }
-
if (speed >= XFER_UDMA_0)
idx = speed - XFER_UDMA_0;
else
@@ -264,6 +258,17 @@ static void scc_set_dmamode (struct ata_port *ap, struct ata_device *adev)
JCTSStbl[offset][idx] << 16 | JCENVTtbl[offset][idx]);
}
+unsigned long scc_mode_filter(struct ata_device *adev, unsigned long mask)
+{
+ /* errata A308 workaround: limit ATAPI UDMA mode to UDMA4 */
+ if (adev->class == ATA_DEV_ATAPI &&
+ (mask & (0xE0 << ATA_SHIFT_UDMA))) {
+ printk(KERN_INFO "%s: limit ATAPI UDMA to UDMA4\n", DRV_NAME);
+ mask &= ~(0xE0 << ATA_SHIFT_UDMA);
+ }
+ return ata_pci_default_filter(adev, mask);
+}
+
/**
* scc_tf_load - send taskfile registers to host controller
* @ap: Port to which output is sent
@@ -358,6 +363,8 @@ static void scc_tf_read (struct ata_port *ap, struct ata_taskfile *tf)
tf->hob_lbal = in_be32(ioaddr->lbal_addr);
tf->hob_lbam = in_be32(ioaddr->lbam_addr);
tf->hob_lbah = in_be32(ioaddr->lbah_addr);
+ out_be32(ioaddr->ctl_addr, tf->ctl);
+ ap->last_ctl = tf->ctl;
}
}
@@ -741,7 +748,7 @@ static u8 scc_bmdma_status (struct ata_port *ap)
return host_stat;
/* errata A252,A308 workaround: Step4 */
- if (ata_altstatus(ap) & ATA_ERR && int_status & INTSTS_INTRQ)
+ if ((ata_altstatus(ap) & ATA_ERR) && (int_status & INTSTS_INTRQ))
return (host_stat | ATA_DMA_INTR);
/* errata A308 workaround Step5 */
@@ -752,11 +759,11 @@ static u8 scc_bmdma_status (struct ata_port *ap)
if ((qc->tf.protocol == ATA_PROT_DMA &&
qc->dev->xfer_mode > XFER_UDMA_4)) {
if (!(int_status & INTSTS_ACTEINT)) {
- printk(KERN_WARNING "ata%u: data lost occurred. (ACTEINT==0, retry:%d)\n",
- ap->print_id, retry);
+ printk(KERN_WARNING "ata%u: operation failed (transfer data loss)\n",
+ ap->print_id);
host_stat |= ATA_DMA_ERR;
if (retry++)
- ap->udma_mask >>= 1;
+ ap->udma_mask &= ~(1 << qc->dev->xfer_mode);
} else
retry = 0;
}
@@ -1016,7 +1023,7 @@ static const struct ata_port_operations scc_pata_ops = {
.port_disable = ata_port_disable,
.set_piomode = scc_set_piomode,
.set_dmamode = scc_set_dmamode,
- .mode_filter = ata_pci_default_filter,
+ .mode_filter = scc_mode_filter,
.tf_load = scc_tf_load,
.tf_read = scc_tf_read,
diff --git a/drivers/ata/sata_inic162x.c b/drivers/ata/sata_inic162x.c
index 3de1834..a9c948d 100644
--- a/drivers/ata/sata_inic162x.c
+++ b/drivers/ata/sata_inic162x.c
@@ -190,34 +190,34 @@ static void inic_reset_port(void __iomem *port_base)
writew(ctl, idma_ctl);
}
-static u32 inic_scr_read(struct ata_port *ap, unsigned sc_reg)
+static int inic_scr_read(struct ata_port *ap, unsigned sc_reg, u32 *val)
{
void __iomem *scr_addr = ap->ioaddr.scr_addr;
void __iomem *addr;
- u32 val;
if (unlikely(sc_reg >= ARRAY_SIZE(scr_map)))
- return 0xffffffffU;
+ return -EINVAL;
addr = scr_addr + scr_map[sc_reg] * 4;
- val = readl(scr_addr + scr_map[sc_reg] * 4);
+ *val = readl(scr_addr + scr_map[sc_reg] * 4);
/* this controller has stuck DIAG.N, ignore it */
if (sc_reg == SCR_ERROR)
- val &= ~SERR_PHYRDY_CHG;
- return val;
+ *val &= ~SERR_PHYRDY_CHG;
+ return 0;
}
-static void inic_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val)
+static int inic_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val)
{
void __iomem *scr_addr = ap->ioaddr.scr_addr;
void __iomem *addr;
if (unlikely(sc_reg >= ARRAY_SIZE(scr_map)))
- return;
+ return -EINVAL;
addr = scr_addr + scr_map[sc_reg] * 4;
writel(val, scr_addr + scr_map[sc_reg] * 4);
+ return 0;
}
/*
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index fb8a749..8ec5208 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -35,8 +35,6 @@
6) Add port multiplier support (intermediate)
- 7) Test and verify 3.0 Gbps support
-
8) Develop a low-power-consumption strategy, and implement it.
9) [Experiment, low priority] See if ATAPI can be supported using
@@ -227,26 +225,26 @@ enum {
EDMA_ERR_IRQ_CAUSE_OFS = 0x8,
EDMA_ERR_IRQ_MASK_OFS = 0xc,
- EDMA_ERR_D_PAR = (1 << 0),
- EDMA_ERR_PRD_PAR = (1 << 1),
- EDMA_ERR_DEV = (1 << 2),
- EDMA_ERR_DEV_DCON = (1 << 3),
- EDMA_ERR_DEV_CON = (1 << 4),
- EDMA_ERR_SERR = (1 << 5),
+ EDMA_ERR_D_PAR = (1 << 0), /* UDMA data parity err */
+ EDMA_ERR_PRD_PAR = (1 << 1), /* UDMA PRD parity err */
+ EDMA_ERR_DEV = (1 << 2), /* device error */
+ EDMA_ERR_DEV_DCON = (1 << 3), /* device disconnect */
+ EDMA_ERR_DEV_CON = (1 << 4), /* device connected */
+ EDMA_ERR_SERR = (1 << 5), /* SError bits [WBDST] raised */
EDMA_ERR_SELF_DIS = (1 << 7), /* Gen II/IIE self-disable */
EDMA_ERR_SELF_DIS_5 = (1 << 8), /* Gen I self-disable */
- EDMA_ERR_BIST_ASYNC = (1 << 8),
+ EDMA_ERR_BIST_ASYNC = (1 << 8), /* BIST FIS or Async Notify */
EDMA_ERR_TRANS_IRQ_7 = (1 << 8), /* Gen IIE transprt layer irq */
- EDMA_ERR_CRBQ_PAR = (1 << 9),
- EDMA_ERR_CRPB_PAR = (1 << 10),
- EDMA_ERR_INTRL_PAR = (1 << 11),
- EDMA_ERR_IORDY = (1 << 12),
- EDMA_ERR_LNK_CTRL_RX = (0xf << 13),
+ EDMA_ERR_CRQB_PAR = (1 << 9), /* CRQB parity error */
+ EDMA_ERR_CRPB_PAR = (1 << 10), /* CRPB parity error */
+ EDMA_ERR_INTRL_PAR = (1 << 11), /* internal parity error */
+ EDMA_ERR_IORDY = (1 << 12), /* IORdy timeout */
+ EDMA_ERR_LNK_CTRL_RX = (0xf << 13), /* link ctrl rx error */
EDMA_ERR_LNK_CTRL_RX_2 = (1 << 15),
- EDMA_ERR_LNK_DATA_RX = (0xf << 17),
- EDMA_ERR_LNK_CTRL_TX = (0x1f << 21),
- EDMA_ERR_LNK_DATA_TX = (0x1f << 26),
- EDMA_ERR_TRANS_PROTO = (1 << 31),
+ EDMA_ERR_LNK_DATA_RX = (0xf << 17), /* link data rx error */
+ EDMA_ERR_LNK_CTRL_TX = (0x1f << 21), /* link ctrl tx error */
+ EDMA_ERR_LNK_DATA_TX = (0x1f << 26), /* link data tx error */
+ EDMA_ERR_TRANS_PROTO = (1 << 31), /* transport protocol error */
EDMA_ERR_OVERRUN_5 = (1 << 5),
EDMA_ERR_UNDERRUN_5 = (1 << 6),
EDMA_EH_FREEZE = EDMA_ERR_D_PAR |
@@ -255,7 +253,7 @@ enum {
EDMA_ERR_DEV_CON |
EDMA_ERR_SERR |
EDMA_ERR_SELF_DIS |
- EDMA_ERR_CRBQ_PAR |
+ EDMA_ERR_CRQB_PAR |
EDMA_ERR_CRPB_PAR |
EDMA_ERR_INTRL_PAR |
EDMA_ERR_IORDY |
@@ -270,7 +268,7 @@ enum {
EDMA_ERR_OVERRUN_5 |
EDMA_ERR_UNDERRUN_5 |
EDMA_ERR_SELF_DIS_5 |
- EDMA_ERR_CRBQ_PAR |
+ EDMA_ERR_CRQB_PAR |
EDMA_ERR_CRPB_PAR |
EDMA_ERR_INTRL_PAR |
EDMA_ERR_IORDY,
@@ -286,10 +284,10 @@ enum {
EDMA_RSP_Q_OUT_PTR_OFS = 0x24, /* also contains BASE_LO */
EDMA_RSP_Q_PTR_SHIFT = 3,
- EDMA_CMD_OFS = 0x28,
- EDMA_EN = (1 << 0),
- EDMA_DS = (1 << 1),
- ATA_RST = (1 << 2),
+ EDMA_CMD_OFS = 0x28, /* EDMA command register */
+ EDMA_EN = (1 << 0), /* enable EDMA */
+ EDMA_DS = (1 << 1), /* disable EDMA; self-negated */
+ ATA_RST = (1 << 2), /* reset trans/link/phy */
EDMA_IORDY_TMOUT = 0x34,
EDMA_ARB_CFG = 0x38,
@@ -301,14 +299,13 @@ enum {
MV_HP_ERRATA_60X1B2 = (1 << 3),
MV_HP_ERRATA_60X1C0 = (1 << 4),
MV_HP_ERRATA_XX42A0 = (1 << 5),
- MV_HP_GEN_I = (1 << 6),
- MV_HP_GEN_II = (1 << 7),
- MV_HP_GEN_IIE = (1 << 8),
+ MV_HP_GEN_I = (1 << 6), /* Generation I: 50xx */
+ MV_HP_GEN_II = (1 << 7), /* Generation II: 60xx */
+ MV_HP_GEN_IIE = (1 << 8), /* Generation IIE: 6042/7042 */
/* Port private flags (pp_flags) */
- MV_PP_FLAG_EDMA_EN = (1 << 0),
- MV_PP_FLAG_EDMA_DS_ACT = (1 << 1),
- MV_PP_FLAG_HAD_A_RESET = (1 << 2),
+ MV_PP_FLAG_EDMA_EN = (1 << 0), /* is EDMA engine enabled? */
+ MV_PP_FLAG_HAD_A_RESET = (1 << 2), /* 1st hard reset complete? */
};
#define IS_GEN_I(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_I)
@@ -318,8 +315,12 @@ enum {
enum {
MV_DMA_BOUNDARY = 0xffffffffU,
+ /* mask of register bits containing lower 32 bits
+ * of EDMA request queue DMA address
+ */
EDMA_REQ_Q_BASE_LO_MASK = 0xfffffc00U,
+ /* ditto, for response queue */
EDMA_RSP_Q_BASE_LO_MASK = 0xffffff00U,
};
@@ -403,10 +404,10 @@ struct mv_host_priv {
};
static void mv_irq_clear(struct ata_port *ap);
-static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in);
-static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
-static u32 mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in);
-static void mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
+static int mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val);
+static int mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
+static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val);
+static int mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
static int mv_port_start(struct ata_port *ap);
static void mv_port_stop(struct ata_port *ap);
static void mv_qc_prep(struct ata_queued_cmd *qc);
@@ -823,7 +824,7 @@ static void mv_start_dma(void __iomem *base, struct mv_host_priv *hpriv,
}
/**
- * mv_stop_dma - Disable eDMA engine
+ * __mv_stop_dma - Disable eDMA engine
* @ap: ATA channel to manipulate
*
* Verify the local cache of the eDMA state is accurate with a
@@ -832,7 +833,7 @@ static void mv_start_dma(void __iomem *base, struct mv_host_priv *hpriv,
* LOCKING:
* Inherited from caller.
*/
-static int mv_stop_dma(struct ata_port *ap)
+static int __mv_stop_dma(struct ata_port *ap)
{
void __iomem *port_mmio = mv_ap_base(ap);
struct mv_port_priv *pp = ap->private_data;
@@ -865,6 +866,18 @@ static int mv_stop_dma(struct ata_port *ap)
return err;
}
+static int mv_stop_dma(struct ata_port *ap)
+{
+ unsigned long flags;
+ int rc;
+
+ spin_lock_irqsave(&ap->host->lock, flags);
+ rc = __mv_stop_dma(ap);
+ spin_unlock_irqrestore(&ap->host->lock, flags);
+
+ return rc;
+}
+
#ifdef ATA_DEBUG
static void mv_dump_mem(void __iomem *start, unsigned bytes)
{
@@ -961,22 +974,26 @@ static unsigned int mv_scr_offset(unsigned int sc_reg_in)
return ofs;
}
-static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in)
+static int mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val)
{
unsigned int ofs = mv_scr_offset(sc_reg_in);
- if (0xffffffffU != ofs)
- return readl(mv_ap_base(ap) + ofs);
- else
- return (u32) ofs;
+ if (ofs != 0xffffffffU) {
+ *val = readl(mv_ap_base(ap) + ofs);
+ return 0;
+ } else
+ return -EINVAL;
}
-static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
+static int mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
{
unsigned int ofs = mv_scr_offset(sc_reg_in);
- if (0xffffffffU != ofs)
+ if (ofs != 0xffffffffU) {
writelfl(val, mv_ap_base(ap) + ofs);
+ return 0;
+ } else
+ return -EINVAL;
}
static void mv_edma_cfg(struct ata_port *ap, struct mv_host_priv *hpriv,
@@ -1029,6 +1046,7 @@ static int mv_port_start(struct ata_port *ap)
void __iomem *port_mmio = mv_ap_base(ap);
void *mem;
dma_addr_t mem_dma;
+ unsigned long flags;
int rc;
pp = devm_kzalloc(dev, sizeof(*pp), GFP_KERNEL);
@@ -1067,10 +1085,14 @@ static int mv_port_start(struct ata_port *ap)
pp->sg_tbl = mem;
pp->sg_tbl_dma = mem_dma;
+ spin_lock_irqsave(&ap->host->lock, flags);
+
mv_edma_cfg(ap, hpriv, port_mmio);
mv_set_edma_ptrs(port_mmio, hpriv, pp);
+ spin_unlock_irqrestore(&ap->host->lock, flags);
+
/* Don't turn on EDMA here...do it before DMA commands only. Else
* we'll be unable to send non-data, PIO, etc due to restricted access
* to shadow regs.
@@ -1090,11 +1112,7 @@ static int mv_port_start(struct ata_port *ap)
*/
static void mv_port_stop(struct ata_port *ap)
{
- unsigned long flags;
-
- spin_lock_irqsave(&ap->host->lock, flags);
mv_stop_dma(ap);
- spin_unlock_irqrestore(&ap->host->lock, flags);
}
/**
@@ -1325,7 +1343,7 @@ static unsigned int mv_qc_issue(struct ata_queued_cmd *qc)
* port. Turn off EDMA so there won't be problems accessing
* shadow block, etc registers.
*/
- mv_stop_dma(ap);
+ __mv_stop_dma(ap);
return ata_qc_issue_prot(qc);
}
@@ -1393,16 +1411,16 @@ static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
if (edma_err_cause & EDMA_ERR_DEV)
err_mask |= AC_ERR_DEV;
if (edma_err_cause & (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR |
- EDMA_ERR_CRBQ_PAR | EDMA_ERR_CRPB_PAR |
+ EDMA_ERR_CRQB_PAR | EDMA_ERR_CRPB_PAR |
EDMA_ERR_INTRL_PAR)) {
err_mask |= AC_ERR_ATA_BUS;
action |= ATA_EH_HARDRESET;
- ata_ehi_push_desc(ehi, ", parity error");
+ ata_ehi_push_desc(ehi, "parity error");
}
if (edma_err_cause & (EDMA_ERR_DEV_DCON | EDMA_ERR_DEV_CON)) {
ata_ehi_hotplugged(ehi);
ata_ehi_push_desc(ehi, edma_err_cause & EDMA_ERR_DEV_DCON ?
- ", dev disconnect" : ", dev connect");
+ "dev disconnect" : "dev connect");
}
if (IS_GEN_I(hpriv)) {
@@ -1411,7 +1429,7 @@ static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
if (edma_err_cause & EDMA_ERR_SELF_DIS_5) {
struct mv_port_priv *pp = ap->private_data;
pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
- ata_ehi_push_desc(ehi, ", EDMA self-disable");
+ ata_ehi_push_desc(ehi, "EDMA self-disable");
}
} else {
eh_freeze_mask = EDMA_EH_FREEZE;
@@ -1419,7 +1437,7 @@ static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
if (edma_err_cause & EDMA_ERR_SELF_DIS) {
struct mv_port_priv *pp = ap->private_data;
pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
- ata_ehi_push_desc(ehi, ", EDMA self-disable");
+ ata_ehi_push_desc(ehi, "EDMA self-disable");
}
if (edma_err_cause & EDMA_ERR_SERR) {
@@ -1489,33 +1507,30 @@ static void mv_intr_edma(struct ata_port *ap)
while (1) {
u16 status;
+ unsigned int tag;
/* get s/w response queue last-read pointer, and compare */
out_index = pp->resp_idx & MV_MAX_Q_DEPTH_MASK;
if (in_index == out_index)
break;
-
/* 50xx: get active ATA command */
- if (IS_GEN_I(hpriv))
- qc = ata_qc_from_tag(ap, ap->active_tag);
+ if (IS_GEN_I(hpriv))
+ tag = ap->active_tag;
- /* 60xx: get active ATA command via tag, to enable support
- * for queueing. this works transparently for queued and
- * non-queued modes.
+ /* Gen II/IIE: get active ATA command via tag, to enable
+ * support for queueing. this works transparently for
+ * queued and non-queued modes.
*/
- else {
- unsigned int tag;
+ else if (IS_GEN_II(hpriv))
+ tag = (le16_to_cpu(pp->crpb[out_index].id)
+ >> CRPB_IOID_SHIFT_6) & 0x3f;
- if (IS_GEN_II(hpriv))
- tag = (le16_to_cpu(pp->crpb[out_index].id)
- >> CRPB_IOID_SHIFT_6) & 0x3f;
- else
- tag = (le16_to_cpu(pp->crpb[out_index].id)
- >> CRPB_IOID_SHIFT_7) & 0x3f;
+ else /* IS_GEN_IIE */
+ tag = (le16_to_cpu(pp->crpb[out_index].id)
+ >> CRPB_IOID_SHIFT_7) & 0x3f;
- qc = ata_qc_from_tag(ap, tag);
- }
+ qc = ata_qc_from_tag(ap, tag);
/* lower 8 bits of status are EDMA_ERR_IRQ_CAUSE_OFS
* bits (WARNING: might not necessarily be associated
@@ -1535,7 +1550,7 @@ static void mv_intr_edma(struct ata_port *ap)
ata_qc_complete(qc);
}
- /* advance software response queue pointer, to
+ /* advance software response queue pointer, to
* indicate (after the loop completes) to hardware
* that we have consumed a response queue entry.
*/
@@ -1741,26 +1756,30 @@ static unsigned int mv5_scr_offset(unsigned int sc_reg_in)
return ofs;
}
-static u32 mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in)
+static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val)
{
void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
void __iomem *addr = mv5_phy_base(mmio, ap->port_no);
unsigned int ofs = mv5_scr_offset(sc_reg_in);
- if (ofs != 0xffffffffU)
- return readl(addr + ofs);
- else
- return (u32) ofs;
+ if (ofs != 0xffffffffU) {
+ *val = readl(addr + ofs);
+ return 0;
+ } else
+ return -EINVAL;
}
-static void mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
+static int mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
{
void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
void __iomem *addr = mv5_phy_base(mmio, ap->port_no);
unsigned int ofs = mv5_scr_offset(sc_reg_in);
- if (ofs != 0xffffffffU)
+ if (ofs != 0xffffffffU) {
writelfl(val, addr + ofs);
+ return 0;
+ } else
+ return -EINVAL;
}
static void mv5_reset_bus(struct pci_dev *pdev, void __iomem *mmio)
@@ -2138,9 +2157,17 @@ static void mv_phy_reset(struct ata_port *ap, unsigned int *class,
VPRINTK("ENTER, port %u, mmio 0x%p\n", ap->port_no, port_mmio);
- DPRINTK("S-regs after ATA_RST: SStat 0x%08x SErr 0x%08x "
- "SCtrl 0x%08x\n", mv_scr_read(ap, SCR_STATUS),
- mv_scr_read(ap, SCR_ERROR), mv_scr_read(ap, SCR_CONTROL));
+#ifdef DEBUG
+ {
+ u32 sstatus, serror, scontrol;
+
+ mv_scr_read(ap, SCR_STATUS, &sstatus);
+ mv_scr_read(ap, SCR_ERROR, &serror);
+ mv_scr_read(ap, SCR_CONTROL, &scontrol);
+ DPRINTK("S-regs after ATA_RST: SStat 0x%08x SErr 0x%08x "
+ "SCtrl 0x%08x\n", status, serror, scontrol);
+ }
+#endif
/* Issue COMRESET via SControl */
comreset_retry:
@@ -2164,9 +2191,17 @@ comreset_retry:
(retry-- > 0))
goto comreset_retry;
- DPRINTK("S-regs after PHY wake: SStat 0x%08x SErr 0x%08x "
- "SCtrl 0x%08x\n", mv_scr_read(ap, SCR_STATUS),
- mv_scr_read(ap, SCR_ERROR), mv_scr_read(ap, SCR_CONTROL));
+#ifdef DEBUG
+ {
+ u32 sstatus, serror, scontrol;
+
+ mv_scr_read(ap, SCR_STATUS, &sstatus);
+ mv_scr_read(ap, SCR_ERROR, &serror);
+ mv_scr_read(ap, SCR_CONTROL, &scontrol);
+ DPRINTK("S-regs after PHY wake: SStat 0x%08x SErr 0x%08x "
+ "SCtrl 0x%08x\n", sstatus, serror, scontrol);
+ }
+#endif
if (ata_port_offline(ap)) {
*class = ATA_DEV_NONE;
@@ -2209,7 +2244,7 @@ static int mv_prereset(struct ata_port *ap, unsigned long deadline)
struct mv_port_priv *pp = ap->private_data;
struct ata_eh_context *ehc = &ap->eh_context;
int rc;
-
+
rc = mv_stop_dma(ap);
if (rc)
ehc->i.action |= ATA_EH_HARDRESET;
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index db81e3e..0b58c4d 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -236,8 +236,8 @@ static void nv_ck804_host_stop(struct ata_host *host);
static irqreturn_t nv_generic_interrupt(int irq, void *dev_instance);
static irqreturn_t nv_nf2_interrupt(int irq, void *dev_instance);
static irqreturn_t nv_ck804_interrupt(int irq, void *dev_instance);
-static u32 nv_scr_read (struct ata_port *ap, unsigned int sc_reg);
-static void nv_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
+static int nv_scr_read (struct ata_port *ap, unsigned int sc_reg, u32 *val);
+static int nv_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static void nv_nf2_freeze(struct ata_port *ap);
static void nv_nf2_thaw(struct ata_port *ap);
@@ -715,19 +715,20 @@ static int nv_adma_check_cpb(struct ata_port *ap, int cpb_num, int force_err)
int freeze = 0;
ata_ehi_clear_desc(ehi);
- ata_ehi_push_desc(ehi, "CPB resp_flags 0x%x", flags );
+ __ata_ehi_push_desc(ehi, "CPB resp_flags 0x%x: ", flags );
if (flags & NV_CPB_RESP_ATA_ERR) {
- ata_ehi_push_desc(ehi, ": ATA error");
+ ata_ehi_push_desc(ehi, "ATA error");
ehi->err_mask |= AC_ERR_DEV;
} else if (flags & NV_CPB_RESP_CMD_ERR) {
- ata_ehi_push_desc(ehi, ": CMD error");
+ ata_ehi_push_desc(ehi, "CMD error");
ehi->err_mask |= AC_ERR_DEV;
} else if (flags & NV_CPB_RESP_CPB_ERR) {
- ata_ehi_push_desc(ehi, ": CPB error");
+ ata_ehi_push_desc(ehi, "CPB error");
ehi->err_mask |= AC_ERR_SYSTEM;
freeze = 1;
} else {
/* notifier error, but no error in CPB flags? */
+ ata_ehi_push_desc(ehi, "unknown");
ehi->err_mask |= AC_ERR_OTHER;
freeze = 1;
}
@@ -854,20 +855,21 @@ static irqreturn_t nv_adma_interrupt(int irq, void *dev_instance)
struct ata_eh_info *ehi = &ap->eh_info;
ata_ehi_clear_desc(ehi);
- ata_ehi_push_desc(ehi, "ADMA status 0x%08x", status );
+ __ata_ehi_push_desc(ehi, "ADMA status 0x%08x: ", status );
if (status & NV_ADMA_STAT_TIMEOUT) {
ehi->err_mask |= AC_ERR_SYSTEM;
- ata_ehi_push_desc(ehi, ": timeout");
+ ata_ehi_push_desc(ehi, "timeout");
} else if (status & NV_ADMA_STAT_HOTPLUG) {
ata_ehi_hotplugged(ehi);
- ata_ehi_push_desc(ehi, ": hotplug");
+ ata_ehi_push_desc(ehi, "hotplug");
} else if (status & NV_ADMA_STAT_HOTUNPLUG) {
ata_ehi_hotplugged(ehi);
- ata_ehi_push_desc(ehi, ": hot unplug");
+ ata_ehi_push_desc(ehi, "hot unplug");
} else if (status & NV_ADMA_STAT_SERROR) {
/* let libata analyze SError and figure out the cause */
- ata_ehi_push_desc(ehi, ": SError");
- }
+ ata_ehi_push_desc(ehi, "SError");
+ } else
+ ata_ehi_push_desc(ehi, "unknown");
ata_port_freeze(ap);
continue;
}
@@ -1391,20 +1393,22 @@ static irqreturn_t nv_ck804_interrupt(int irq, void *dev_instance)
return ret;
}
-static u32 nv_scr_read (struct ata_port *ap, unsigned int sc_reg)
+static int nv_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val)
{
if (sc_reg > SCR_CONTROL)
- return 0xffffffffU;
+ return -EINVAL;
- return ioread32(ap->ioaddr.scr_addr + (sc_reg * 4));
+ *val = ioread32(ap->ioaddr.scr_addr + (sc_reg * 4));
+ return 0;
}
-static void nv_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
+static int nv_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val)
{
if (sc_reg > SCR_CONTROL)
- return;
+ return -EINVAL;
iowrite32(val, ap->ioaddr.scr_addr + (sc_reg * 4));
+ return 0;
}
static void nv_nf2_freeze(struct ata_port *ap)
diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c
index d2fcb9a..d39ebc2 100644
--- a/drivers/ata/sata_promise.c
+++ b/drivers/ata/sata_promise.c
@@ -128,8 +128,8 @@ struct pdc_port_priv {
dma_addr_t pkt_dma;
};
-static u32 pdc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg);
-static void pdc_sata_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
+static int pdc_sata_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val);
+static int pdc_sata_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val);
static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
static int pdc_common_port_start(struct ata_port *ap);
static int pdc_sata_port_start(struct ata_port *ap);
@@ -427,19 +427,20 @@ static int pdc_sata_cable_detect(struct ata_port *ap)
return ATA_CBL_SATA;
}
-static u32 pdc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
+static int pdc_sata_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val)
{
if (sc_reg > SCR_CONTROL)
- return 0xffffffffU;
- return readl(ap->ioaddr.scr_addr + (sc_reg * 4));
+ return -EINVAL;
+ *val = readl(ap->ioaddr.scr_addr + (sc_reg * 4));
+ return 0;
}
-static void pdc_sata_scr_write (struct ata_port *ap, unsigned int sc_reg,
- u32 val)
+static int pdc_sata_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val)
{
if (sc_reg > SCR_CONTROL)
- return;
+ return -EINVAL;
writel(val, ap->ioaddr.scr_addr + (sc_reg * 4));
+ return 0;
}
static void pdc_atapi_pkt(struct ata_queued_cmd *qc)
@@ -642,8 +643,12 @@ static void pdc_error_intr(struct ata_port *ap, struct ata_queued_cmd *qc,
| PDC_PCI_SYS_ERR | PDC1_PCI_PARITY_ERR))
ac_err_mask |= AC_ERR_HOST_BUS;
- if (sata_scr_valid(ap))
- ehi->serror |= pdc_sata_scr_read(ap, SCR_ERROR);
+ if (sata_scr_valid(ap)) {
+ u32 serror;
+
+ pdc_sata_scr_read(ap, SCR_ERROR, &serror);
+ ehi->serror |= serror;
+ }
qc->err_mask |= ac_err_mask;
diff --git a/drivers/ata/sata_qstor.c b/drivers/ata/sata_qstor.c
index 9ab554d..c8f9242 100644
--- a/drivers/ata/sata_qstor.c
+++ b/drivers/ata/sata_qstor.c
@@ -111,8 +111,8 @@ struct qs_port_priv {
qs_state_t state;
};
-static u32 qs_scr_read (struct ata_port *ap, unsigned int sc_reg);
-static void qs_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
+static int qs_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val);
+static int qs_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val);
static int qs_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
static int qs_port_start(struct ata_port *ap);
static void qs_host_stop(struct ata_host *host);
@@ -255,18 +255,20 @@ static void qs_eng_timeout(struct ata_port *ap)
ata_eng_timeout(ap);
}
-static u32 qs_scr_read (struct ata_port *ap, unsigned int sc_reg)
+static int qs_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val)
{
if (sc_reg > SCR_CONTROL)
- return ~0U;
- return readl(ap->ioaddr.scr_addr + (sc_reg * 8));
+ return -EINVAL;
+ *val = readl(ap->ioaddr.scr_addr + (sc_reg * 8));
+ return 0;
}
-static void qs_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
+static int qs_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val)
{
if (sc_reg > SCR_CONTROL)
- return;
+ return -EINVAL;
writel(val, ap->ioaddr.scr_addr + (sc_reg * 8));
+ return 0;
}
static unsigned int qs_fill_sg(struct ata_queued_cmd *qc)
@@ -337,7 +339,7 @@ static void qs_qc_prep(struct ata_queued_cmd *qc)
buf[28] = dflags;
/* frame information structure (FIS) */
- ata_tf_to_fis(&qc->tf, &buf[32], 0);
+ ata_tf_to_fis(&qc->tf, 0, 1, &buf[32]);
}
static inline void qs_packet_start(struct ata_queued_cmd *qc)
diff --git a/drivers/ata/sata_sil.c b/drivers/ata/sata_sil.c
index 2a86dc4..db67637 100644
--- a/drivers/ata/sata_sil.c
+++ b/drivers/ata/sata_sil.c
@@ -115,8 +115,8 @@ static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
static int sil_pci_device_resume(struct pci_dev *pdev);
#endif
static void sil_dev_config(struct ata_device *dev);
-static u32 sil_scr_read (struct ata_port *ap, unsigned int sc_reg);
-static void sil_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
+static int sil_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val);
+static int sil_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val);
static int sil_set_mode (struct ata_port *ap, struct ata_device **r_failed);
static void sil_freeze(struct ata_port *ap);
static void sil_thaw(struct ata_port *ap);
@@ -350,19 +350,26 @@ static inline void __iomem *sil_scr_addr(struct ata_port *ap, unsigned int sc_re
return NULL;
}
-static u32 sil_scr_read (struct ata_port *ap, unsigned int sc_reg)
+static int sil_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val)
{
void __iomem *mmio = sil_scr_addr(ap, sc_reg);
- if (mmio)
- return readl(mmio);
- return 0xffffffffU;
+
+ if (mmio) {
+ *val = readl(mmio);
+ return 0;
+ }
+ return -EINVAL;
}
-static void sil_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
+static int sil_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val)
{
void __iomem *mmio = sil_scr_addr(ap, sc_reg);
- if (mmio)
+
+ if (mmio) {
writel(val, mmio);
+ return 0;
+ }
+ return -EINVAL;
}
static void sil_host_intr(struct ata_port *ap, u32 bmdma2)
@@ -378,7 +385,7 @@ static void sil_host_intr(struct ata_port *ap, u32 bmdma2)
* controllers continue to assert IRQ as long as
* SError bits are pending. Clear SError immediately.
*/
- serror = sil_scr_read(ap, SCR_ERROR);
+ sil_scr_read(ap, SCR_ERROR, &serror);
sil_scr_write(ap, SCR_ERROR, serror);
/* Trigger hotplug and accumulate SError only if the
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index ac43a30..46fbbe7 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -326,8 +326,8 @@ struct sil24_port_priv {
static void sil24_dev_config(struct ata_device *dev);
static u8 sil24_check_status(struct ata_port *ap);
-static u32 sil24_scr_read(struct ata_port *ap, unsigned sc_reg);
-static void sil24_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val);
+static int sil24_scr_read(struct ata_port *ap, unsigned sc_reg, u32 *val);
+static int sil24_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val);
static void sil24_tf_read(struct ata_port *ap, struct ata_taskfile *tf);
static void sil24_qc_prep(struct ata_queued_cmd *qc);
static unsigned int sil24_qc_issue(struct ata_queued_cmd *qc);
@@ -464,15 +464,15 @@ static void sil24_dev_config(struct ata_device *dev)
writel(PORT_CS_CDB16, port + PORT_CTRL_CLR);
}
-static inline void sil24_update_tf(struct ata_port *ap)
+static void sil24_read_tf(struct ata_port *ap, int tag, struct ata_taskfile *tf)
{
- struct sil24_port_priv *pp = ap->private_data;
void __iomem *port = ap->ioaddr.cmd_addr;
- struct sil24_prb __iomem *prb = port;
+ struct sil24_prb __iomem *prb;
u8 fis[6 * 4];
- memcpy_fromio(fis, prb->fis, 6 * 4);
- ata_tf_from_fis(fis, &pp->tf);
+ prb = port + PORT_LRAM + sil24_tag(tag) * PORT_LRAM_SLOT_SZ;
+ memcpy_fromio(fis, prb->fis, sizeof(fis));
+ ata_tf_from_fis(fis, tf);
}
static u8 sil24_check_status(struct ata_port *ap)
@@ -488,25 +488,30 @@ static int sil24_scr_map[] = {
[SCR_ACTIVE] = 3,
};
-static u32 sil24_scr_read(struct ata_port *ap, unsigned sc_reg)
+static int sil24_scr_read(struct ata_port *ap, unsigned sc_reg, u32 *val)
{
void __iomem *scr_addr = ap->ioaddr.scr_addr;
+
if (sc_reg < ARRAY_SIZE(sil24_scr_map)) {
void __iomem *addr;
addr = scr_addr + sil24_scr_map[sc_reg] * 4;
- return readl(scr_addr + sil24_scr_map[sc_reg] * 4);
+ *val = readl(scr_addr + sil24_scr_map[sc_reg] * 4);
+ return 0;
}
- return 0xffffffffU;
+ return -EINVAL;
}
-static void sil24_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val)
+static int sil24_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val)
{
void __iomem *scr_addr = ap->ioaddr.scr_addr;
+
if (sc_reg < ARRAY_SIZE(sil24_scr_map)) {
void __iomem *addr;
addr = scr_addr + sil24_scr_map[sc_reg] * 4;
writel(val, scr_addr + sil24_scr_map[sc_reg] * 4);
+ return 0;
}
+ return -EINVAL;
}
static void sil24_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
@@ -531,15 +536,60 @@ static int sil24_init_port(struct ata_port *ap)
return 0;
}
-static int sil24_softreset(struct ata_port *ap, unsigned int *class,
- unsigned long deadline)
+static int sil24_exec_polled_cmd(struct ata_port *ap, int pmp,
+ const struct ata_taskfile *tf,
+ int is_cmd, u32 ctrl,
+ unsigned long timeout_msec)
{
void __iomem *port = ap->ioaddr.cmd_addr;
struct sil24_port_priv *pp = ap->private_data;
struct sil24_prb *prb = &pp->cmd_block[0].ata.prb;
dma_addr_t paddr = pp->cmd_block_dma;
- u32 mask, irq_stat;
+ u32 irq_enabled, irq_mask, irq_stat;
+ int rc;
+
+ prb->ctrl = cpu_to_le16(ctrl);
+ ata_tf_to_fis(tf, pmp, is_cmd, prb->fis);
+
+ /* temporarily plug completion and error interrupts */
+ irq_enabled = readl(port + PORT_IRQ_ENABLE_SET);
+ writel(PORT_IRQ_COMPLETE | PORT_IRQ_ERROR, port + PORT_IRQ_ENABLE_CLR);
+
+ writel((u32)paddr, port + PORT_CMD_ACTIVATE);
+ writel((u64)paddr >> 32, port + PORT_CMD_ACTIVATE + 4);
+
+ irq_mask = (PORT_IRQ_COMPLETE | PORT_IRQ_ERROR) << PORT_IRQ_RAW_SHIFT;
+ irq_stat = ata_wait_register(port + PORT_IRQ_STAT, irq_mask, 0x0,
+ 10, timeout_msec);
+
+ writel(irq_mask, port + PORT_IRQ_STAT); /* clear IRQs */
+ irq_stat >>= PORT_IRQ_RAW_SHIFT;
+
+ if (irq_stat & PORT_IRQ_COMPLETE)
+ rc = 0;
+ else {
+ /* force port into known state */
+ sil24_init_port(ap);
+
+ if (irq_stat & PORT_IRQ_ERROR)
+ rc = -EIO;
+ else
+ rc = -EBUSY;
+ }
+
+ /* restore IRQ enabled */
+ writel(irq_enabled, port + PORT_IRQ_ENABLE_SET);
+
+ return rc;
+}
+
+static int sil24_do_softreset(struct ata_port *ap, unsigned int *class,
+ int pmp, unsigned long deadline)
+{
+ unsigned long timeout_msec = 0;
+ struct ata_taskfile tf;
const char *reason;
+ int rc;
DPRINTK("ENTER\n");
@@ -556,29 +606,22 @@ static int sil24_softreset(struct ata_port *ap, unsigned int *class,
}
/* do SRST */
- prb->ctrl = cpu_to_le16(PRB_CTRL_SRST);
- prb->fis[1] = 0; /* no PMP yet */
-
- writel((u32)paddr, port + PORT_CMD_ACTIVATE);
- writel((u64)paddr >> 32, port + PORT_CMD_ACTIVATE + 4);
-
- mask = (PORT_IRQ_COMPLETE | PORT_IRQ_ERROR) << PORT_IRQ_RAW_SHIFT;
- irq_stat = ata_wait_register(port + PORT_IRQ_STAT, mask, 0x0,
- 100, jiffies_to_msecs(deadline - jiffies));
-
- writel(irq_stat, port + PORT_IRQ_STAT); /* clear IRQs */
- irq_stat >>= PORT_IRQ_RAW_SHIFT;
-
- if (!(irq_stat & PORT_IRQ_COMPLETE)) {
- if (irq_stat & PORT_IRQ_ERROR)
- reason = "SRST command error";
- else
- reason = "timeout";
+ if (time_after(deadline, jiffies))
+ timeout_msec = jiffies_to_msecs(deadline - jiffies);
+
+ ata_tf_init(ap->device, &tf); /* doesn't really matter */
+ rc = sil24_exec_polled_cmd(ap, pmp, &tf, 0, PRB_CTRL_SRST,
+ timeout_msec);
+ if (rc == -EBUSY) {
+ reason = "timeout";
+ goto err;
+ } else if (rc) {
+ reason = "SRST command error";
goto err;
}
- sil24_update_tf(ap);
- *class = ata_dev_classify(&pp->tf);
+ sil24_read_tf(ap, 0, &tf);
+ *class = ata_dev_classify(&tf);
if (*class == ATA_DEV_UNKNOWN)
*class = ATA_DEV_NONE;
@@ -592,6 +635,12 @@ static int sil24_softreset(struct ata_port *ap, unsigned int *class,
return -EIO;
}
+static int sil24_softreset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
+{
+ return sil24_do_softreset(ap, class, 0, deadline);
+}
+
static int sil24_hardreset(struct ata_port *ap, unsigned int *class,
unsigned long deadline)
{
@@ -699,7 +748,7 @@ static void sil24_qc_prep(struct ata_queued_cmd *qc)
}
prb->ctrl = cpu_to_le16(ctrl);
- ata_tf_to_fis(&qc->tf, prb->fis, 0);
+ ata_tf_to_fis(&qc->tf, 0, 1, prb->fis);
if (qc->flags & ATA_QCFLAG_DMAMAP)
sil24_fill_sg(qc, sge);
@@ -754,6 +803,7 @@ static void sil24_thaw(struct ata_port *ap)
static void sil24_error_intr(struct ata_port *ap)
{
void __iomem *port = ap->ioaddr.cmd_addr;
+ struct sil24_port_priv *pp = ap->private_data;
struct ata_eh_info *ehi = &ap->eh_info;
int freeze = 0;
u32 irq_stat;
@@ -769,16 +819,16 @@ static void sil24_error_intr(struct ata_port *ap)
if (irq_stat & (PORT_IRQ_PHYRDY_CHG | PORT_IRQ_DEV_XCHG)) {
ata_ehi_hotplugged(ehi);
- ata_ehi_push_desc(ehi, ", %s",
- irq_stat & PORT_IRQ_PHYRDY_CHG ?
- "PHY RDY changed" : "device exchanged");
+ ata_ehi_push_desc(ehi, "%s",
+ irq_stat & PORT_IRQ_PHYRDY_CHG ?
+ "PHY RDY changed" : "device exchanged");
freeze = 1;
}
if (irq_stat & PORT_IRQ_UNK_FIS) {
ehi->err_mask |= AC_ERR_HSM;
ehi->action |= ATA_EH_SOFTRESET;
- ata_ehi_push_desc(ehi , ", unknown FIS");
+ ata_ehi_push_desc(ehi, "unknown FIS");
freeze = 1;
}
@@ -797,18 +847,18 @@ static void sil24_error_intr(struct ata_port *ap)
if (ci && ci->desc) {
err_mask |= ci->err_mask;
action |= ci->action;
- ata_ehi_push_desc(ehi, ", %s", ci->desc);
+ ata_ehi_push_desc(ehi, "%s", ci->desc);
} else {
err_mask |= AC_ERR_OTHER;
action |= ATA_EH_SOFTRESET;
- ata_ehi_push_desc(ehi, ", unknown command error %d",
+ ata_ehi_push_desc(ehi, "unknown command error %d",
cerr);
}
/* record error info */
qc = ata_qc_from_tag(ap, ap->active_tag);
if (qc) {
- sil24_update_tf(ap);
+ sil24_read_tf(ap, qc->tag, &pp->tf);
qc->err_mask |= err_mask;
} else
ehi->err_mask |= err_mask;
@@ -825,8 +875,11 @@ static void sil24_error_intr(struct ata_port *ap)
static void sil24_finish_qc(struct ata_queued_cmd *qc)
{
+ struct ata_port *ap = qc->ap;
+ struct sil24_port_priv *pp = ap->private_data;
+
if (qc->flags & ATA_QCFLAG_RESULT_TF)
- sil24_update_tf(qc->ap);
+ sil24_read_tf(ap, qc->tag, &pp->tf);
}
static inline void sil24_host_intr(struct ata_port *ap)
diff --git a/drivers/ata/sata_sis.c b/drivers/ata/sata_sis.c
index 33716b0..31a2f55 100644
--- a/drivers/ata/sata_sis.c
+++ b/drivers/ata/sata_sis.c
@@ -64,8 +64,8 @@ enum {
};
static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
-static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg);
-static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
+static int sis_scr_read (struct ata_port *ap, unsigned int sc_reg, u32 *val);
+static int sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static const struct pci_device_id sis_pci_tbl[] = {
{ PCI_VDEVICE(SI, 0x0180), sis_180 }, /* SiS 964/180 */
@@ -207,36 +207,37 @@ static void sis_scr_cfg_write (struct ata_port *ap, unsigned int sc_reg, u32 val
pci_write_config_dword(pdev, cfg_addr+0x10, val);
}
-static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg)
+static int sis_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 val, val2 = 0;
u8 pmr;
if (sc_reg > SCR_CONTROL)
- return 0xffffffffU;
+ return -EINVAL;
if (ap->flags & SIS_FLAG_CFGSCR)
return sis_scr_cfg_read(ap, sc_reg);
pci_read_config_byte(pdev, SIS_PMR, &pmr);
- val = ioread32(ap->ioaddr.scr_addr + (sc_reg * 4));
+ *val = ioread32(ap->ioaddr.scr_addr + (sc_reg * 4));
if ((pdev->device == 0x0182) || (pdev->device == 0x0183) ||
(pdev->device == 0x1182) || (pmr & SIS_PMR_COMBINED))
- val2 = ioread32(ap->ioaddr.scr_addr + (sc_reg * 4) + 0x10);
+ *val |= ioread32(ap->ioaddr.scr_addr + (sc_reg * 4) + 0x10);
+
+ *val &= 0xfffffffb;
- return (val | val2) & 0xfffffffb;
+ return 0;
}
-static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
+static int sis_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u8 pmr;
if (sc_reg > SCR_CONTROL)
- return;
+ return -EINVAL;
pci_read_config_byte(pdev, SIS_PMR, &pmr);
@@ -248,6 +249,7 @@ static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
(pdev->device == 0x1182) || (pmr & SIS_PMR_COMBINED))
iowrite32(val, ap->ioaddr.scr_addr + (sc_reg * 4)+0x10);
}
+ return 0;
}
static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
diff --git a/drivers/ata/sata_svw.c b/drivers/ata/sata_svw.c
index 63fe99a..92e8770 100644
--- a/drivers/ata/sata_svw.c
+++ b/drivers/ata/sata_svw.c
@@ -103,20 +103,21 @@ static int k2_sata_check_atapi_dma(struct ata_queued_cmd *qc)
return 0;
}
-static u32 k2_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
+static int k2_sata_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val)
{
if (sc_reg > SCR_CONTROL)
- return 0xffffffffU;
- return readl(ap->ioaddr.scr_addr + (sc_reg * 4));
+ return -EINVAL;
+ *val = readl(ap->ioaddr.scr_addr + (sc_reg * 4));
+ return 0;
}
-static void k2_sata_scr_write (struct ata_port *ap, unsigned int sc_reg,
- u32 val)
+static int k2_sata_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val)
{
if (sc_reg > SCR_CONTROL)
- return;
+ return -EINVAL;
writel(val, ap->ioaddr.scr_addr + (sc_reg * 4));
+ return 0;
}
diff --git a/drivers/ata/sata_uli.c b/drivers/ata/sata_uli.c
index b52f83a..78c2851 100644
--- a/drivers/ata/sata_uli.c
+++ b/drivers/ata/sata_uli.c
@@ -57,8 +57,8 @@ struct uli_priv {
};
static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
-static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg);
-static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
+static int uli_scr_read (struct ata_port *ap, unsigned int sc_reg, u32 *val);
+static int uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static const struct pci_device_id uli_pci_tbl[] = {
{ PCI_VDEVICE(AL, 0x5289), uli_5289 },
@@ -164,20 +164,22 @@ static void uli_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val)
pci_write_config_dword(pdev, cfg_addr, val);
}
-static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg)
+static int uli_scr_read (struct ata_port *ap, unsigned int sc_reg, u32 *val)
{
if (sc_reg > SCR_CONTROL)
- return 0xffffffffU;
+ return -EINVAL;
- return uli_scr_cfg_read(ap, sc_reg);
+ *val = uli_scr_cfg_read(ap, sc_reg);
+ return 0;
}
-static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
+static int uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
{
if (sc_reg > SCR_CONTROL) //SCR_CONTROL=2, SCR_ERROR=1, SCR_STATUS=0
- return;
+ return -EINVAL;
uli_scr_cfg_write(ap, sc_reg, val);
+ return 0;
}
static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index c412447..86b7bfc 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -72,8 +72,8 @@ enum {
};
static int svia_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
-static u32 svia_scr_read (struct ata_port *ap, unsigned int sc_reg);
-static void svia_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
+static int svia_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val);
+static int svia_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val);
static void svia_noop_freeze(struct ata_port *ap);
static void vt6420_error_handler(struct ata_port *ap);
static int vt6421_pata_cable_detect(struct ata_port *ap);
@@ -249,18 +249,20 @@ MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, svia_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-static u32 svia_scr_read (struct ata_port *ap, unsigned int sc_reg)
+static int svia_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val)
{
if (sc_reg > SCR_CONTROL)
- return 0xffffffffU;
- return ioread32(ap->ioaddr.scr_addr + (4 * sc_reg));
+ return -EINVAL;
+ *val = ioread32(ap->ioaddr.scr_addr + (4 * sc_reg));
+ return 0;
}
-static void svia_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
+static int svia_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val)
{
if (sc_reg > SCR_CONTROL)
- return;
+ return -EINVAL;
iowrite32(val, ap->ioaddr.scr_addr + (4 * sc_reg));
+ return 0;
}
static void svia_noop_freeze(struct ata_port *ap)
@@ -305,18 +307,19 @@ static int vt6420_prereset(struct ata_port *ap, unsigned long deadline)
/* Resume phy. This is the old SATA resume sequence */
svia_scr_write(ap, SCR_CONTROL, 0x300);
- svia_scr_read(ap, SCR_CONTROL); /* flush */
+ svia_scr_read(ap, SCR_CONTROL, &scontrol); /* flush */
/* wait for phy to become ready, if necessary */
do {
msleep(200);
- if ((svia_scr_read(ap, SCR_STATUS) & 0xf) != 1)
+ svia_scr_read(ap, SCR_STATUS, &sstatus);
+ if ((sstatus & 0xf) != 1)
break;
} while (time_before(jiffies, timeout));
/* open code sata_print_link_status() */
- sstatus = svia_scr_read(ap, SCR_STATUS);
- scontrol = svia_scr_read(ap, SCR_CONTROL);
+ svia_scr_read(ap, SCR_STATUS, &sstatus);
+ svia_scr_read(ap, SCR_CONTROL, &scontrol);
online = (sstatus & 0xf) == 0x3;
@@ -325,7 +328,7 @@ static int vt6420_prereset(struct ata_port *ap, unsigned long deadline)
online ? "up" : "down", sstatus, scontrol);
/* SStatus is read one more time */
- svia_scr_read(ap, SCR_STATUS);
+ svia_scr_read(ap, SCR_STATUS, &sstatus);
if (!online) {
/* tell EH to bail */
diff --git a/drivers/ata/sata_vsc.c b/drivers/ata/sata_vsc.c
index 1b5d81f..24344d0 100644
--- a/drivers/ata/sata_vsc.c
+++ b/drivers/ata/sata_vsc.c
@@ -98,20 +98,21 @@ enum {
VSC_SATA_INT_PHY_CHANGE),
};
-static u32 vsc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
+static int vsc_sata_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val)
{
if (sc_reg > SCR_CONTROL)
- return 0xffffffffU;
- return readl(ap->ioaddr.scr_addr + (sc_reg * 4));
+ return -EINVAL;
+ *val = readl(ap->ioaddr.scr_addr + (sc_reg * 4));
+ return 0;
}
-static void vsc_sata_scr_write (struct ata_port *ap, unsigned int sc_reg,
- u32 val)
+static int vsc_sata_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val)
{
if (sc_reg > SCR_CONTROL)
- return;
+ return -EINVAL;
writel(val, ap->ioaddr.scr_addr + (sc_reg * 4));
+ return 0;
}
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 47cd2a1..be5a439 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -323,6 +323,7 @@ enum ata_completion_errors {
AC_ERR_INVALID = (1 << 7), /* invalid argument */
AC_ERR_OTHER = (1 << 8), /* unknown */
AC_ERR_NODEV_HINT = (1 << 9), /* polling device detection hint */
+ AC_ERR_NCQ = (1 << 10), /* marker for offending NCQ qc */
};
/* forward declarations */
@@ -530,6 +531,7 @@ struct ata_port {
unsigned int cbl; /* cable type; ATA_CBL_xxx */
unsigned int hw_sata_spd_limit;
unsigned int sata_spd_limit; /* SATA PHY speed limit */
+ unsigned int sata_spd; /* current SATA PHY speed */
/* record runtime error info, protected by host lock */
struct ata_eh_info eh_info;
@@ -563,6 +565,9 @@ struct ata_port {
pm_message_t pm_mesg;
int *pm_result;
+ struct timer_list fastdrain_timer;
+ unsigned long fastdrain_cnt;
+
void *private_data;
#ifdef CONFIG_ATA_ACPI
@@ -619,9 +624,8 @@ struct ata_port_operations {
u8 (*irq_on) (struct ata_port *);
u8 (*irq_ack) (struct ata_port *ap, unsigned int chk_drq);
- u32 (*scr_read) (struct ata_port *ap, unsigned int sc_reg);
- void (*scr_write) (struct ata_port *ap, unsigned int sc_reg,
- u32 val);
+ int (*scr_read) (struct ata_port *ap, unsigned int sc_reg, u32 *val);
+ int (*scr_write) (struct ata_port *ap, unsigned int sc_reg, u32 val);
int (*port_suspend) (struct ata_port *ap, pm_message_t mesg);
int (*port_resume) (struct ata_port *ap);
@@ -764,7 +768,8 @@ extern unsigned int ata_dev_try_classify(struct ata_port *, unsigned int, u8 *);
*/
extern void ata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf);
extern void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf);
-extern void ata_tf_to_fis(const struct ata_taskfile *tf, u8 *fis, u8 pmp);
+extern void ata_tf_to_fis(const struct ata_taskfile *tf,
+ u8 pmp, int is_cmd, u8 *fis);
extern void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf);
extern void ata_noop_dev_select (struct ata_port *ap, unsigned int device);
extern void ata_std_dev_select (struct ata_port *ap, unsigned int device);
@@ -909,27 +914,21 @@ extern void ata_do_eh(struct ata_port *ap, ata_prereset_fn_t prereset,
/*
* ata_eh_info helpers
*/
-#define ata_ehi_push_desc(ehi, fmt, args...) do { \
- (ehi)->desc_len += scnprintf((ehi)->desc + (ehi)->desc_len, \
- ATA_EH_DESC_LEN - (ehi)->desc_len, \
- fmt , ##args); \
-} while (0)
-
-#define ata_ehi_clear_desc(ehi) do { \
- (ehi)->desc[0] = '\0'; \
- (ehi)->desc_len = 0; \
-} while (0)
-
-static inline void __ata_ehi_hotplugged(struct ata_eh_info *ehi)
+extern void __ata_ehi_push_desc(struct ata_eh_info *ehi, const char *fmt, ...);
+extern void ata_ehi_push_desc(struct ata_eh_info *ehi, const char *fmt, ...);
+extern void ata_ehi_clear_desc(struct ata_eh_info *ehi);
+
+static inline void ata_ehi_schedule_probe(struct ata_eh_info *ehi)
{
- ehi->flags |= ATA_EHI_HOTPLUGGED | ATA_EHI_RESUME_LINK;
+ ehi->flags |= ATA_EHI_RESUME_LINK;
ehi->action |= ATA_EH_SOFTRESET;
ehi->probe_mask |= (1 << ATA_MAX_DEVICES) - 1;
}
static inline void ata_ehi_hotplugged(struct ata_eh_info *ehi)
{
- __ata_ehi_hotplugged(ehi);
+ ata_ehi_schedule_probe(ehi);
+ ehi->flags |= ATA_EHI_HOTPLUGGED;
ehi->err_mask |= AC_ERR_ATA_BUS;
}
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2007-07-12 20:20 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2007-07-12 20:20 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Tejun's Port Multiplier support, one of the larger libata merge items
for 2.6.23, is still pending. This is mostly cleanups and minor
improvements, though sata_mv received a much-needed facelift.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/Kconfig | 10 +-
drivers/ata/ata_piix.c | 2 +-
drivers/ata/libata-core.c | 74 +---
drivers/ata/libata-eh.c | 96 +++---
drivers/ata/libata-sff.c | 288 ++-------------
drivers/ata/pata_hpt3x3.c | 93 ++++-
drivers/ata/pata_mpc52xx.c | 18 +-
drivers/ata/pata_scc.c | 54 ++-
drivers/ata/pata_sis.c | 3 +
drivers/ata/sata_mv.c | 887 ++++++++++++++++++++++++++++----------------
drivers/ata/sata_nv.c | 2 +-
drivers/ata/sata_promise.c | 41 ++-
drivers/ata/sata_sis.c | 2 +-
drivers/ata/sata_uli.c | 2 +-
drivers/ata/sata_via.c | 2 +-
include/linux/ata.h | 29 ++
include/linux/libata.h | 12 +-
17 files changed, 890 insertions(+), 725 deletions(-)
Akira Iguchi (1):
pata_scc.c: Workaround for errata A308
Alan Cox (2):
pata_sis: FIFO whack
pata_hpt3x3: major reworking and testing
Albert Lee (1):
libata: remove irq_on from ata_bus_reset() and ata_std_postreset()
Chuck Ebbert (1):
libata: add another Maxtor drive with broken NCQ to the list
Domen Puncer (1):
pata_mpc52xx: suspend/resume support
Jeff Garzik (5):
pata_hpt3x3: fix DMA Kconfig option to actually have a hope of working
[libata] sata_mv: Minor cleanups and renaming, preparing for new EH & NCQ
[libata] sata_mv: minor bug fixes, enhancements, and cleanups (prep for new EH)
[libata] sata_mv: Convert to new exception handling (EH) infrastructure
[libata] sata_mv: Fix and clean up per-chip-generation tests
Mikael Pettersson (1):
sata_promise: SATA hotplug support, take 2
Oleg Nesterov (1):
libata-core: convert to use cancel_rearming_delayed_work()
Prarit Bhargava (1):
Add Hitachi HDS7250SASUN500G 0621KTAWSD to NCQ blacklist
Tejun Heo (7):
libata: simplify PCI legacy SFF host handling
libata: quirk IOMEGA ZIP 250 ATAPI FLOPPY
libata: clean up horkage handling
libata: add FUJITSU MHV2080BH to NCQ blacklist
libata-link: separate out ata_eh_handle_dev_fail()
libata-link: add PMP related ATA constants
ata_piix: kill incorrect invalid map value warning
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 4ad8675..d8046a1 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -309,7 +309,7 @@ config PATA_HPT3X2N
If unsure, say N.
config PATA_HPT3X3
- tristate "HPT 343/363 PATA support (Experimental)"
+ tristate "HPT 343/363 PATA support"
depends on PCI
help
This option enables support for the HPT 343/363
@@ -317,6 +317,14 @@ config PATA_HPT3X3
If unsure, say N.
+config PATA_HPT3X3_DMA
+ bool "HPT 343/363 DMA support (Experimental)"
+ depends on PATA_HPT3X3
+ help
+ This option enables DMA support for the HPT343/363
+ controllers. Enable with care as there are still some
+ problems with DMA on this chipset.
+
config PATA_ISAPNP
tristate "ISA Plug and Play PATA support (Experimental)"
depends on EXPERIMENTAL && ISAPNP
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 6a3bfef..21a7ca4 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -414,7 +414,7 @@ static const struct piix_map_db ich6m_map_db = {
*/
.map = {
/* PM PS SM SS MAP */
- { P0, P2, RV, RV }, /* 00b */
+ { P0, P2, NA, NA }, /* 00b */
{ IDE, IDE, P1, P3 }, /* 01b */
{ P0, P2, IDE, IDE }, /* 10b */
{ RV, RV, RV, RV },
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 5b25311..88e2dd0 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -71,6 +71,7 @@ static unsigned int ata_dev_init_params(struct ata_device *dev,
u16 heads, u16 sectors);
static unsigned int ata_dev_set_xfermode(struct ata_device *dev);
static void ata_dev_xfermask(struct ata_device *dev);
+static unsigned long ata_dev_blacklisted(const struct ata_device *dev);
unsigned int ata_print_id = 1;
static struct workqueue_struct *ata_wq;
@@ -1283,18 +1284,11 @@ static unsigned int ata_id_xfermask(const u16 *id)
void ata_port_queue_task(struct ata_port *ap, work_func_t fn, void *data,
unsigned long delay)
{
- int rc;
-
- if (ap->pflags & ATA_PFLAG_FLUSH_PORT_TASK)
- return;
-
PREPARE_DELAYED_WORK(&ap->port_task, fn);
ap->port_task_data = data;
- rc = queue_delayed_work(ata_wq, &ap->port_task, delay);
-
- /* rc == 0 means that another user is using port task */
- WARN_ON(rc == 0);
+ /* may fail if ata_port_flush_task() in progress */
+ queue_delayed_work(ata_wq, &ap->port_task, delay);
}
/**
@@ -1309,32 +1303,9 @@ void ata_port_queue_task(struct ata_port *ap, work_func_t fn, void *data,
*/
void ata_port_flush_task(struct ata_port *ap)
{
- unsigned long flags;
-
DPRINTK("ENTER\n");
- spin_lock_irqsave(ap->lock, flags);
- ap->pflags |= ATA_PFLAG_FLUSH_PORT_TASK;
- spin_unlock_irqrestore(ap->lock, flags);
-
- DPRINTK("flush #1\n");
- cancel_work_sync(&ap->port_task.work); /* akpm: seems unneeded */
-
- /*
- * At this point, if a task is running, it's guaranteed to see
- * the FLUSH flag; thus, it will never queue pio tasks again.
- * Cancel and flush.
- */
- if (!cancel_delayed_work(&ap->port_task)) {
- if (ata_msg_ctl(ap))
- ata_port_printk(ap, KERN_DEBUG, "%s: flush #2\n",
- __FUNCTION__);
- cancel_work_sync(&ap->port_task.work);
- }
-
- spin_lock_irqsave(ap->lock, flags);
- ap->pflags &= ~ATA_PFLAG_FLUSH_PORT_TASK;
- spin_unlock_irqrestore(ap->lock, flags);
+ cancel_rearming_delayed_work(&ap->port_task);
if (ata_msg_ctl(ap))
ata_port_printk(ap, KERN_DEBUG, "%s: EXIT\n", __FUNCTION__);
@@ -1814,7 +1785,7 @@ static void ata_dev_config_ncq(struct ata_device *dev,
desc[0] = '\0';
return;
}
- if (ata_device_blacklisted(dev) & ATA_HORKAGE_NONCQ) {
+ if (dev->horkage & ATA_HORKAGE_NONCQ) {
snprintf(desc, desc_sz, "NCQ (not used)");
return;
}
@@ -1863,6 +1834,9 @@ int ata_dev_configure(struct ata_device *dev)
if (ata_msg_probe(ap))
ata_dev_printk(dev, KERN_DEBUG, "%s: ENTER\n", __FUNCTION__);
+ /* set horkage */
+ dev->horkage |= ata_dev_blacklisted(dev);
+
/* let ACPI work its magic */
rc = ata_acpi_on_devcfg(dev);
if (rc)
@@ -2038,7 +2012,7 @@ int ata_dev_configure(struct ata_device *dev)
dev->max_sectors = ATA_MAX_SECTORS;
}
- if (ata_device_blacklisted(dev) & ATA_HORKAGE_MAX_SEC_128)
+ if (dev->horkage & ATA_HORKAGE_MAX_SEC_128)
dev->max_sectors = min_t(unsigned int, ATA_MAX_SECTORS_128,
dev->max_sectors);
@@ -3190,9 +3164,6 @@ void ata_bus_reset(struct ata_port *ap)
if ((slave_possible) && (err != 0x81))
ap->device[1].class = ata_dev_try_classify(ap, 1, &err);
- /* re-enable interrupts */
- ap->ops->irq_on(ap);
-
/* is double-select really necessary? */
if (ap->device[1].class != ATA_DEV_NONE)
ap->ops->dev_select(ap, 1);
@@ -3577,10 +3548,6 @@ void ata_std_postreset(struct ata_port *ap, unsigned int *classes)
if (sata_scr_read(ap, SCR_ERROR, &serror) == 0)
sata_scr_write(ap, SCR_ERROR, serror);
- /* re-enable interrupts */
- if (!ap->ops->error_handler)
- ap->ops->irq_on(ap);
-
/* is double-select really necessary? */
if (classes[0] != ATA_DEV_NONE)
ap->ops->dev_select(ap, 1);
@@ -3770,6 +3737,8 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
{ "SAMSUNG CD-ROM SN-124","N001", ATA_HORKAGE_NODMA },
{ "Seagate STT20000A", NULL, ATA_HORKAGE_NODMA },
{ "IOMEGA ZIP 250 ATAPI", NULL, ATA_HORKAGE_NODMA }, /* temporary fix */
+ { "IOMEGA ZIP 250 ATAPI Floppy",
+ NULL, ATA_HORKAGE_NODMA },
/* Weird ATAPI devices */
{ "TORiSAN DVD-ROM DRD-N216", NULL, ATA_HORKAGE_MAX_SEC_128 },
@@ -3783,7 +3752,10 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
{ "FUJITSU MHT2060BH", NULL, ATA_HORKAGE_NONCQ },
/* NCQ is broken */
{ "Maxtor 6L250S0", "BANC1G10", ATA_HORKAGE_NONCQ },
+ { "Maxtor 6B200M0", "BANC1BM0", ATA_HORKAGE_NONCQ },
{ "Maxtor 6B200M0", "BANC1B10", ATA_HORKAGE_NONCQ },
+ { "HITACHI HDS7250SASUN500G 0621KTAWSD", "K2AOAJ0AHITACHI",
+ ATA_HORKAGE_NONCQ },
/* NCQ hard hangs device under heavier load, needs hard power cycle */
{ "Maxtor 6B250S0", "BANC1B70", ATA_HORKAGE_NONCQ },
/* Blacklist entries taken from Silicon Image 3124/3132
@@ -3796,6 +3768,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
{ "HTS541612J9SA00", "SBDIC7JP", ATA_HORKAGE_NONCQ, },
{ "Hitachi HTS541616J9SA00", "SB4OC70P", ATA_HORKAGE_NONCQ, },
{ "WDC WD740ADFD-00NLR1", NULL, ATA_HORKAGE_NONCQ, },
+ { "FUJITSU MHV2080BH", "00840028", ATA_HORKAGE_NONCQ, },
/* Devices with NCQ limits */
@@ -3803,7 +3776,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
{ }
};
-unsigned long ata_device_blacklisted(const struct ata_device *dev)
+static unsigned long ata_dev_blacklisted(const struct ata_device *dev)
{
unsigned char model_num[ATA_ID_PROD_LEN + 1];
unsigned char model_rev[ATA_ID_FW_REV_LEN + 1];
@@ -3833,7 +3806,7 @@ static int ata_dma_blacklisted(const struct ata_device *dev)
if ((dev->ap->flags & ATA_FLAG_PIO_POLLING) &&
(dev->flags & ATA_DFLAG_CDB_INTR))
return 1;
- return (ata_device_blacklisted(dev) & ATA_HORKAGE_NODMA) ? 1 : 0;
+ return (dev->horkage & ATA_HORKAGE_NODMA) ? 1 : 0;
}
/**
@@ -6557,13 +6530,7 @@ void ata_port_detach(struct ata_port *ap)
spin_unlock_irqrestore(ap->lock, flags);
ata_port_wait_eh(ap);
-
- /* Flush hotplug task. The sequence is similar to
- * ata_port_flush_task().
- */
- cancel_work_sync(&ap->hotplug_task.work); /* akpm: why? */
- cancel_delayed_work(&ap->hotplug_task);
- cancel_work_sync(&ap->hotplug_task.work);
+ cancel_rearming_delayed_work(&ap->hotplug_task);
skip_eh:
/* remove the associated SCSI host */
@@ -6952,7 +6919,6 @@ EXPORT_SYMBOL_GPL(ata_host_resume);
EXPORT_SYMBOL_GPL(ata_id_string);
EXPORT_SYMBOL_GPL(ata_id_c_string);
EXPORT_SYMBOL_GPL(ata_id_to_dma_mode);
-EXPORT_SYMBOL_GPL(ata_device_blacklisted);
EXPORT_SYMBOL_GPL(ata_scsi_simulate);
EXPORT_SYMBOL_GPL(ata_pio_need_iordy);
@@ -6961,9 +6927,9 @@ EXPORT_SYMBOL_GPL(ata_timing_merge);
#ifdef CONFIG_PCI
EXPORT_SYMBOL_GPL(pci_test_config_bits);
-EXPORT_SYMBOL_GPL(ata_pci_init_native_host);
+EXPORT_SYMBOL_GPL(ata_pci_init_sff_host);
EXPORT_SYMBOL_GPL(ata_pci_init_bmdma);
-EXPORT_SYMBOL_GPL(ata_pci_prepare_native_host);
+EXPORT_SYMBOL_GPL(ata_pci_prepare_sff_host);
EXPORT_SYMBOL_GPL(ata_pci_init_one);
EXPORT_SYMBOL_GPL(ata_pci_remove_one);
#ifdef CONFIG_PM
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 9ee0a8c..9aa62a0 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -1897,6 +1897,57 @@ static int ata_eh_skip_recovery(struct ata_port *ap)
return 1;
}
+static void ata_eh_handle_dev_fail(struct ata_device *dev, int err)
+{
+ struct ata_port *ap = dev->ap;
+ struct ata_eh_context *ehc = &ap->eh_context;
+
+ ehc->tries[dev->devno]--;
+
+ switch (err) {
+ case -ENODEV:
+ /* device missing or wrong IDENTIFY data, schedule probing */
+ ehc->i.probe_mask |= (1 << dev->devno);
+ case -EINVAL:
+ /* give it just one more chance */
+ ehc->tries[dev->devno] = min(ehc->tries[dev->devno], 1);
+ case -EIO:
+ if (ehc->tries[dev->devno] == 1) {
+ /* This is the last chance, better to slow
+ * down than lose it.
+ */
+ sata_down_spd_limit(ap);
+ ata_down_xfermask_limit(dev, ATA_DNXFER_PIO);
+ }
+ }
+
+ if (ata_dev_enabled(dev) && !ehc->tries[dev->devno]) {
+ /* disable device if it has used up all its chances */
+ ata_dev_disable(dev);
+
+ /* detach if offline */
+ if (ata_port_offline(ap))
+ ata_eh_detach_dev(dev);
+
+ /* probe if requested */
+ if ((ehc->i.probe_mask & (1 << dev->devno)) &&
+ !(ehc->did_probe_mask & (1 << dev->devno))) {
+ ata_eh_detach_dev(dev);
+ ata_dev_init(dev);
+
+ ehc->tries[dev->devno] = ATA_EH_DEV_TRIES;
+ ehc->did_probe_mask |= (1 << dev->devno);
+ ehc->i.action |= ATA_EH_SOFTRESET;
+ }
+ } else {
+ /* soft didn't work? be haaaaard */
+ if (ehc->i.flags & ATA_EHI_DID_RESET)
+ ehc->i.action |= ATA_EH_HARDRESET;
+ else
+ ehc->i.action |= ATA_EH_SOFTRESET;
+ }
+}
+
/**
* ata_eh_recover - recover host port after error
* @ap: host port to recover
@@ -1997,50 +2048,7 @@ static int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
goto out;
dev_fail:
- ehc->tries[dev->devno]--;
-
- switch (rc) {
- case -ENODEV:
- /* device missing or wrong IDENTIFY data, schedule probing */
- ehc->i.probe_mask |= (1 << dev->devno);
- case -EINVAL:
- /* give it just one more chance */
- ehc->tries[dev->devno] = min(ehc->tries[dev->devno], 1);
- case -EIO:
- if (ehc->tries[dev->devno] == 1) {
- /* This is the last chance, better to slow
- * down than lose it.
- */
- sata_down_spd_limit(ap);
- ata_down_xfermask_limit(dev, ATA_DNXFER_PIO);
- }
- }
-
- if (ata_dev_enabled(dev) && !ehc->tries[dev->devno]) {
- /* disable device if it has used up all its chances */
- ata_dev_disable(dev);
-
- /* detach if offline */
- if (ata_port_offline(ap))
- ata_eh_detach_dev(dev);
-
- /* probe if requested */
- if ((ehc->i.probe_mask & (1 << dev->devno)) &&
- !(ehc->did_probe_mask & (1 << dev->devno))) {
- ata_eh_detach_dev(dev);
- ata_dev_init(dev);
-
- ehc->tries[dev->devno] = ATA_EH_DEV_TRIES;
- ehc->did_probe_mask |= (1 << dev->devno);
- ehc->i.action |= ATA_EH_SOFTRESET;
- }
- } else {
- /* soft didn't work? be haaaaard */
- if (ehc->i.flags & ATA_EHI_DID_RESET)
- ehc->i.action |= ATA_EH_HARDRESET;
- else
- ehc->i.action |= ATA_EH_SOFTRESET;
- }
+ ata_eh_handle_dev_fail(dev, rc);
if (ata_port_nr_enabled(ap)) {
ata_port_printk(ap, KERN_WARNING, "failed to recover some "
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index fa1c22c..ca7d224 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -604,13 +604,17 @@ int ata_pci_init_bmdma(struct ata_host *host)
}
/**
- * ata_pci_init_native_host - acquire native ATA resources and init host
+ * ata_pci_init_sff_host - acquire native PCI ATA resources and init host
* @host: target ATA host
*
* Acquire native PCI ATA resources for @host and initialize the
* first two ports of @host accordingly. Ports marked dummy are
* skipped and allocation failure makes the port dummy.
*
+ * Note that native PCI resources are valid even for legacy hosts
+ * as we fix up pdev resources array early in boot, so this
+ * function can be used for both native and legacy SFF hosts.
+ *
* LOCKING:
* Inherited from calling layer (may sleep).
*
@@ -618,7 +622,7 @@ int ata_pci_init_bmdma(struct ata_host *host)
* 0 if at least one port is initialized, -ENODEV if no port is
* available.
*/
-int ata_pci_init_native_host(struct ata_host *host)
+int ata_pci_init_sff_host(struct ata_host *host)
{
struct device *gdev = host->dev;
struct pci_dev *pdev = to_pci_dev(gdev);
@@ -673,7 +677,7 @@ int ata_pci_init_native_host(struct ata_host *host)
}
/**
- * ata_pci_prepare_native_host - helper to prepare native PCI ATA host
+ * ata_pci_prepare_sff_host - helper to prepare native PCI ATA host
* @pdev: target PCI device
* @ppi: array of port_info, must be enough for two ports
* @r_host: out argument for the initialized ATA host
@@ -687,9 +691,9 @@ int ata_pci_init_native_host(struct ata_host *host)
* RETURNS:
* 0 on success, -errno otherwise.
*/
-int ata_pci_prepare_native_host(struct pci_dev *pdev,
- const struct ata_port_info * const * ppi,
- struct ata_host **r_host)
+int ata_pci_prepare_sff_host(struct pci_dev *pdev,
+ const struct ata_port_info * const * ppi,
+ struct ata_host **r_host)
{
struct ata_host *host;
int rc;
@@ -705,7 +709,7 @@ int ata_pci_prepare_native_host(struct pci_dev *pdev,
goto err_out;
}
- rc = ata_pci_init_native_host(host);
+ rc = ata_pci_init_sff_host(host);
if (rc)
goto err_out;
@@ -730,221 +734,6 @@ int ata_pci_prepare_native_host(struct pci_dev *pdev,
return rc;
}
-struct ata_legacy_devres {
- unsigned int mask;
- unsigned long cmd_port[2];
- void __iomem * cmd_addr[2];
- void __iomem * ctl_addr[2];
- unsigned int irq[2];
- void * irq_dev_id[2];
-};
-
-static void ata_legacy_free_irqs(struct ata_legacy_devres *legacy_dr)
-{
- int i;
-
- for (i = 0; i < 2; i++) {
- if (!legacy_dr->irq[i])
- continue;
-
- free_irq(legacy_dr->irq[i], legacy_dr->irq_dev_id[i]);
- legacy_dr->irq[i] = 0;
- legacy_dr->irq_dev_id[i] = NULL;
- }
-}
-
-static void ata_legacy_release(struct device *gdev, void *res)
-{
- struct ata_legacy_devres *this = res;
- int i;
-
- ata_legacy_free_irqs(this);
-
- for (i = 0; i < 2; i++) {
- if (this->cmd_addr[i])
- ioport_unmap(this->cmd_addr[i]);
- if (this->ctl_addr[i])
- ioport_unmap(this->ctl_addr[i]);
- if (this->cmd_port[i])
- release_region(this->cmd_port[i], 8);
- }
-}
-
-static int ata_init_legacy_port(struct ata_port *ap,
- struct ata_legacy_devres *legacy_dr)
-{
- struct ata_host *host = ap->host;
- int port_no = ap->port_no;
- unsigned long cmd_port, ctl_port;
-
- if (port_no == 0) {
- cmd_port = ATA_PRIMARY_CMD;
- ctl_port = ATA_PRIMARY_CTL;
- } else {
- cmd_port = ATA_SECONDARY_CMD;
- ctl_port = ATA_SECONDARY_CTL;
- }
-
- /* request cmd_port */
- if (request_region(cmd_port, 8, "libata"))
- legacy_dr->cmd_port[port_no] = cmd_port;
- else {
- dev_printk(KERN_WARNING, host->dev,
- "0x%0lX IDE port busy\n", cmd_port);
- return -EBUSY;
- }
-
- /* iomap cmd and ctl ports */
- legacy_dr->cmd_addr[port_no] = ioport_map(cmd_port, 8);
- legacy_dr->ctl_addr[port_no] = ioport_map(ctl_port, 1);
- if (!legacy_dr->cmd_addr[port_no] || !legacy_dr->ctl_addr[port_no]) {
- dev_printk(KERN_WARNING, host->dev,
- "failed to map cmd/ctl ports\n");
- return -ENOMEM;
- }
-
- /* init IO addresses */
- ap->ioaddr.cmd_addr = legacy_dr->cmd_addr[port_no];
- ap->ioaddr.altstatus_addr = legacy_dr->ctl_addr[port_no];
- ap->ioaddr.ctl_addr = legacy_dr->ctl_addr[port_no];
- ata_std_ports(&ap->ioaddr);
-
- return 0;
-}
-
-/**
- * ata_init_legacy_host - acquire legacy ATA resources and init ATA host
- * @host: target ATA host
- * @was_busy: out parameter, indicates whether any port was busy
- *
- * Acquire legacy ATA resources for the first two ports of @host
- * and initialize it accordingly. Ports marked dummy are skipped
- * and resource acquistion failure makes the port dummy.
- *
- * LOCKING:
- * Inherited from calling layer (may sleep).
- *
- * RETURNS:
- * 0 if at least one port is initialized, -ENODEV if no port is
- * available.
- */
-static int ata_init_legacy_host(struct ata_host *host, int *was_busy)
-{
- struct device *gdev = host->dev;
- struct ata_legacy_devres *legacy_dr;
- int i, rc;
-
- if (!devres_open_group(gdev, NULL, GFP_KERNEL))
- return -ENOMEM;
-
- rc = -ENOMEM;
- legacy_dr = devres_alloc(ata_legacy_release, sizeof(*legacy_dr),
- GFP_KERNEL);
- if (!legacy_dr)
- goto err_out;
- devres_add(gdev, legacy_dr);
-
- for (i = 0; i < 2; i++) {
- if (ata_port_is_dummy(host->ports[i]))
- continue;
-
- rc = ata_init_legacy_port(host->ports[i], legacy_dr);
- if (rc == 0)
- legacy_dr->mask |= 1 << i;
- else {
- if (rc == -EBUSY)
- (*was_busy)++;
- host->ports[i]->ops = &ata_dummy_port_ops;
- }
- }
-
- if (!legacy_dr->mask) {
- dev_printk(KERN_ERR, gdev, "no available legacy port\n");
- return -ENODEV;
- }
-
- devres_remove_group(gdev, NULL);
- return 0;
-
- err_out:
- devres_release_group(gdev, NULL);
- return rc;
-}
-
-/**
- * ata_request_legacy_irqs - request legacy ATA IRQs
- * @host: target ATA host
- * @handler: array of IRQ handlers
- * @irq_flags: array of IRQ flags
- * @dev_id: array of IRQ dev_ids
- *
- * Request legacy IRQs for non-dummy legacy ports in @host. All
- * IRQ parameters are passed as array to allow ports to have
- * separate IRQ handlers.
- *
- * LOCKING:
- * Inherited from calling layer (may sleep).
- *
- * RETURNS:
- * 0 on success, -errno otherwise.
- */
-static int ata_request_legacy_irqs(struct ata_host *host,
- irq_handler_t const *handler,
- const unsigned int *irq_flags,
- void * const *dev_id)
-{
- struct device *gdev = host->dev;
- struct ata_legacy_devres *legacy_dr;
- int i, rc;
-
- legacy_dr = devres_find(host->dev, ata_legacy_release, NULL, NULL);
- BUG_ON(!legacy_dr);
-
- for (i = 0; i < 2; i++) {
- unsigned int irq;
-
- /* FIXME: ATA_*_IRQ() should take generic device not pci_dev */
- if (i == 0)
- irq = ATA_PRIMARY_IRQ(to_pci_dev(gdev));
- else
- irq = ATA_SECONDARY_IRQ(to_pci_dev(gdev));
-
- if (!(legacy_dr->mask & (1 << i)))
- continue;
-
- if (!handler[i]) {
- dev_printk(KERN_ERR, gdev,
- "NULL handler specified for port %d\n", i);
- rc = -EINVAL;
- goto err_out;
- }
-
- rc = request_irq(irq, handler[i], irq_flags[i], DRV_NAME,
- dev_id[i]);
- if (rc) {
- dev_printk(KERN_ERR, gdev,
- "irq %u request failed (errno=%d)\n", irq, rc);
- goto err_out;
- }
-
- /* record irq allocation in legacy_dr */
- legacy_dr->irq[i] = irq;
- legacy_dr->irq_dev_id[i] = dev_id[i];
-
- /* only used to print info */
- if (i == 0)
- host->irq = irq;
- else
- host->irq2 = irq;
- }
-
- return 0;
-
- err_out:
- ata_legacy_free_irqs(legacy_dr);
- return rc;
-}
-
/**
* ata_pci_init_one - Initialize/register PCI IDE host controller
* @pdev: Controller to be initialized
@@ -1029,35 +818,11 @@ int ata_pci_init_one(struct pci_dev *pdev,
#endif
}
- /* alloc and init host */
- host = ata_host_alloc_pinfo(dev, ppi, 2);
- if (!host) {
- dev_printk(KERN_ERR, &pdev->dev,
- "failed to allocate ATA host\n");
- rc = -ENOMEM;
+ /* prepare host */
+ rc = ata_pci_prepare_sff_host(pdev, ppi, &host);
+ if (rc)
goto err_out;
- }
- if (!legacy_mode) {
- rc = ata_pci_init_native_host(host);
- if (rc)
- goto err_out;
- } else {
- int was_busy = 0;
-
- rc = ata_init_legacy_host(host, &was_busy);
- if (was_busy)
- pcim_pin_device(pdev);
- if (rc)
- goto err_out;
-
- /* request respective PCI regions, may fail */
- rc = pci_request_region(pdev, 1, DRV_NAME);
- rc = pci_request_region(pdev, 3, DRV_NAME);
- }
-
- /* init BMDMA, may fail */
- ata_pci_init_bmdma(host);
pci_set_master(pdev);
/* start host and request IRQ */
@@ -1068,17 +833,28 @@ int ata_pci_init_one(struct pci_dev *pdev,
if (!legacy_mode) {
rc = devm_request_irq(dev, pdev->irq, pi->port_ops->irq_handler,
IRQF_SHARED, DRV_NAME, host);
+ if (rc)
+ goto err_out;
host->irq = pdev->irq;
} else {
- irq_handler_t handler[2] = { host->ops->irq_handler,
- host->ops->irq_handler };
- unsigned int irq_flags[2] = { IRQF_SHARED, IRQF_SHARED };
- void *dev_id[2] = { host, host };
+ if (!ata_port_is_dummy(host->ports[0])) {
+ host->irq = ATA_PRIMARY_IRQ(pdev);
+ rc = devm_request_irq(dev, host->irq,
+ pi->port_ops->irq_handler,
+ IRQF_SHARED, DRV_NAME, host);
+ if (rc)
+ goto err_out;
+ }
- rc = ata_request_legacy_irqs(host, handler, irq_flags, dev_id);
+ if (!ata_port_is_dummy(host->ports[1])) {
+ host->irq2 = ATA_SECONDARY_IRQ(pdev);
+ rc = devm_request_irq(dev, host->irq2,
+ pi->port_ops->irq_handler,
+ IRQF_SHARED, DRV_NAME, host);
+ if (rc)
+ goto err_out;
+ }
}
- if (rc)
- goto err_out;
/* register */
rc = ata_host_register(host, pi->sht);
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
index d928c91..be0f05e 100644
--- a/drivers/ata/pata_hpt3x3.c
+++ b/drivers/ata/pata_hpt3x3.c
@@ -23,7 +23,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x3"
-#define DRV_VERSION "0.4.3"
+#define DRV_VERSION "0.5.3"
/**
* hpt3x3_set_piomode - PIO setup
@@ -52,6 +52,7 @@ static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev)
pci_write_config_dword(pdev, 0x48, r2);
}
+#if defined(CONFIG_PATA_HPT3X3_DMA)
/**
* hpt3x3_set_dmamode - DMA timing setup
* @ap: ATA interface
@@ -59,6 +60,9 @@ static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev)
*
* Set up the channel for MWDMA or UDMA modes. Much the same as with
* PIO, load the mode number and then set MWDMA or UDMA flag.
+ *
+ * 0x44 : bit 0-2 master mode, 3-5 slave mode, etc
+ * 0x48 : bit 4/0 DMA/UDMA bit 5/1 for slave etc
*/
static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev)
@@ -76,13 +80,26 @@ static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev)
r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */
if (adev->dma_mode >= XFER_UDMA_0)
- r2 |= 0x01 << dn; /* Ultra mode */
+ r2 |= (0x10 << dn); /* Ultra mode */
else
- r2 |= 0x10 << dn; /* MWDMA */
+ r2 |= (0x01 << dn); /* MWDMA */
pci_write_config_dword(pdev, 0x44, r1);
pci_write_config_dword(pdev, 0x48, r2);
}
+#endif /* CONFIG_PATA_HPT3X3_DMA */
+
+/**
+ * hpt3x3_atapi_dma - ATAPI DMA check
+ * @qc: Queued command
+ *
+ * Just say no - we don't do ATAPI DMA
+ */
+
+static int hpt3x3_atapi_dma(struct ata_queued_cmd *qc)
+{
+ return 1;
+}
static struct scsi_host_template hpt3x3_sht = {
.module = THIS_MODULE,
@@ -105,7 +122,9 @@ static struct scsi_host_template hpt3x3_sht = {
static struct ata_port_operations hpt3x3_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = hpt3x3_set_piomode,
+#if defined(CONFIG_PATA_HPT3X3_DMA)
.set_dmamode = hpt3x3_set_dmamode,
+#endif
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
@@ -124,6 +143,7 @@ static struct ata_port_operations hpt3x3_port_ops = {
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
+ .check_atapi_dma= hpt3x3_atapi_dma,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
@@ -158,32 +178,79 @@ static void hpt3x3_init_chipset(struct pci_dev *dev)
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
}
-
/**
* hpt3x3_init_one - Initialise an HPT343/363
- * @dev: PCI device
+ * @pdev: PCI device
* @id: Entry in match table
*
- * Perform basic initialisation. The chip has a quirk that it won't
- * function unless it is at XX00. The old ATA driver touched this up
- * but we leave it for pci quirks to do properly.
+ * Perform basic initialisation. We set the device up so we access all
+ * ports via BAR4. This is neccessary to work around errata.
*/
-static int hpt3x3_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
+ static int printed_version;
static const struct ata_port_info info = {
.sht = &hpt3x3_sht,
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
+#if defined(CONFIG_PATA_HPT3X3_DMA)
+ /* Further debug needed */
.mwdma_mask = 0x07,
.udma_mask = 0x07,
+#endif
.port_ops = &hpt3x3_port_ops
};
+ /* Register offsets of taskfiles in BAR4 area */
+ static const u8 offset_cmd[2] = { 0x20, 0x28 };
+ static const u8 offset_ctl[2] = { 0x36, 0x3E };
const struct ata_port_info *ppi[] = { &info, NULL };
-
- hpt3x3_init_chipset(dev);
- /* Now kick off ATA set up */
- return ata_pci_init_one(dev, ppi);
+ struct ata_host *host;
+ int i, rc;
+ void __iomem *base;
+
+ hpt3x3_init_chipset(pdev);
+
+ if (!printed_version++)
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
+
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
+ if (!host)
+ return -ENOMEM;
+ /* acquire resources and fill host */
+ rc = pcim_enable_device(pdev);
+ if (rc)
+ return rc;
+
+ /* Everything is relative to BAR4 if we set up this way */
+ rc = pcim_iomap_regions(pdev, 1 << 4, DRV_NAME);
+ if (rc == -EBUSY)
+ pcim_pin_device(pdev);
+ if (rc)
+ return rc;
+ host->iomap = pcim_iomap_table(pdev);
+ rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+ if (rc)
+ return rc;
+ rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+ if (rc)
+ return rc;
+
+ base = host->iomap[4]; /* Bus mastering base */
+
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_ioports *ioaddr = &host->ports[i]->ioaddr;
+
+ ioaddr->cmd_addr = base + offset_cmd[i];
+ ioaddr->altstatus_addr =
+ ioaddr->ctl_addr = base + offset_ctl[i];
+ ioaddr->scr_addr = NULL;
+ ata_std_ports(ioaddr);
+ ioaddr->bmdma_addr = base + 8 * i;
+ }
+ pci_set_master(pdev);
+ return ata_host_activate(host, pdev->irq, ata_interrupt, IRQF_SHARED,
+ &hpt3x3_sht);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_mpc52xx.c b/drivers/ata/pata_mpc52xx.c
index 368fac7..182e83c 100644
--- a/drivers/ata/pata_mpc52xx.c
+++ b/drivers/ata/pata_mpc52xx.c
@@ -467,13 +467,27 @@ mpc52xx_ata_remove(struct of_device *op)
static int
mpc52xx_ata_suspend(struct of_device *op, pm_message_t state)
{
- return 0; /* FIXME : What to do here ? */
+ struct ata_host *host = dev_get_drvdata(&op->dev);
+
+ return ata_host_suspend(host, state);
}
static int
mpc52xx_ata_resume(struct of_device *op)
{
- return 0; /* FIXME : What to do here ? */
+ struct ata_host *host = dev_get_drvdata(&op->dev);
+ struct mpc52xx_ata_priv *priv = host->private_data;
+ int rv;
+
+ rv = mpc52xx_ata_hw_init(priv);
+ if (rv) {
+ printk(KERN_ERR DRV_NAME ": Error during HW init\n");
+ return rv;
+ }
+
+ ata_host_resume(host);
+
+ return 0;
}
#endif
diff --git a/drivers/ata/pata_scc.c b/drivers/ata/pata_scc.c
index 61502bc..c55667e 100644
--- a/drivers/ata/pata_scc.c
+++ b/drivers/ata/pata_scc.c
@@ -238,6 +238,12 @@ static void scc_set_dmamode (struct ata_port *ap, struct ata_device *adev)
else
offset = 0; /* 100MHz */
+ /* errata A308 workaround: limit ATAPI UDMA mode to UDMA4 */
+ if (adev->class == ATA_DEV_ATAPI && speed > XFER_UDMA_4) {
+ printk(KERN_INFO "%s: limit ATAPI UDMA to UDMA4\n", DRV_NAME);
+ speed = XFER_UDMA_4;
+ }
+
if (speed >= XFER_UDMA_0)
idx = speed - XFER_UDMA_0;
else
@@ -724,22 +730,36 @@ static void scc_bmdma_stop (struct ata_queued_cmd *qc)
static u8 scc_bmdma_status (struct ata_port *ap)
{
- u8 host_stat;
void __iomem *mmio = ap->ioaddr.bmdma_addr;
-
- host_stat = in_be32(mmio + SCC_DMA_STATUS);
-
- /* Workaround for PTERADD: emulate DMA_INTR when
- * - IDE_STATUS[ERR] = 1
- * - INT_STATUS[INTRQ] = 1
- * - DMA_STATUS[IORACTA] = 1
- */
- if (!(host_stat & ATA_DMA_INTR)) {
- u32 int_status = in_be32(mmio + SCC_DMA_INTST);
- if (ata_altstatus(ap) & ATA_ERR &&
- int_status & INTSTS_INTRQ &&
- host_stat & ATA_DMA_ACTIVE)
- host_stat |= ATA_DMA_INTR;
+ u8 host_stat = in_be32(mmio + SCC_DMA_STATUS);
+ u32 int_status = in_be32(mmio + SCC_DMA_INTST);
+ struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->active_tag);
+ static int retry = 0;
+
+ /* return if IOS_SS is cleared */
+ if (!(in_be32(mmio + SCC_DMA_CMD) & ATA_DMA_START))
+ return host_stat;
+
+ /* errata A252,A308 workaround: Step4 */
+ if (ata_altstatus(ap) & ATA_ERR && int_status & INTSTS_INTRQ)
+ return (host_stat | ATA_DMA_INTR);
+
+ /* errata A308 workaround Step5 */
+ if (int_status & INTSTS_IOIRQS) {
+ host_stat |= ATA_DMA_INTR;
+
+ /* We don't check ATAPI DMA because it is limited to UDMA4 */
+ if ((qc->tf.protocol == ATA_PROT_DMA &&
+ qc->dev->xfer_mode > XFER_UDMA_4)) {
+ if (!(int_status & INTSTS_ACTEINT)) {
+ printk(KERN_WARNING "ata%u: data lost occurred. (ACTEINT==0, retry:%d)\n",
+ ap->print_id, retry);
+ host_stat |= ATA_DMA_ERR;
+ if (retry++)
+ ap->udma_mask >>= 1;
+ } else
+ retry = 0;
+ }
}
return host_stat;
@@ -892,10 +912,6 @@ static void scc_std_postreset (struct ata_port *ap, unsigned int *classes)
{
DPRINTK("ENTER\n");
- /* re-enable interrupts */
- if (!ap->ops->error_handler)
- ap->ops->irq_on(ap);
-
/* is double-select really necessary? */
if (classes[0] != ATA_DEV_NONE)
ap->ops->dev_select(ap, 1);
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index 2b45082..657b1ee 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -149,6 +149,9 @@ static int sis_pre_reset(struct ata_port *ap, unsigned long deadline)
if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no]))
return -ENOENT;
+ /* Clear the FIFO settings. We can't enable the FIFO until
+ we know we are poking at a disk */
+ pci_write_config_byte(pdev, 0x4B, 0);
return ata_std_prereset(ap, deadline);
}
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 3873b29..8a77a0a 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -29,11 +29,6 @@
I distinctly remember a couple workarounds (one related to PCI-X)
are still needed.
- 2) Convert to LibATA new EH. Required for hotplug, NCQ, and sane
- probing/error handling in general. MUST HAVE.
-
- 3) Add hotplug support (easy, once new-EH support appears)
-
4) Add NCQ support (easy to intermediate, once new-EH support appears)
5) Investigate problems with PCI Message Signalled Interrupts (MSI).
@@ -108,8 +103,6 @@ enum {
MV_SATAHC_ARBTR_REG_SZ = MV_MINOR_REG_AREA_SZ, /* arbiter */
MV_PORT_REG_SZ = MV_MINOR_REG_AREA_SZ,
- MV_USE_Q_DEPTH = ATA_DEF_QUEUE,
-
MV_MAX_Q_DEPTH = 32,
MV_MAX_Q_DEPTH_MASK = MV_MAX_Q_DEPTH - 1,
@@ -133,18 +126,22 @@ enum {
/* Host Flags */
MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */
MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */
- MV_COMMON_FLAGS = (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO |
- ATA_FLAG_NO_ATAPI | ATA_FLAG_PIO_POLLING),
+ MV_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+ ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI |
+ ATA_FLAG_PIO_POLLING,
MV_6XXX_FLAGS = MV_FLAG_IRQ_COALESCE,
CRQB_FLAG_READ = (1 << 0),
CRQB_TAG_SHIFT = 1,
+ CRQB_IOID_SHIFT = 6, /* CRQB Gen-II/IIE IO Id shift */
+ CRQB_HOSTQ_SHIFT = 17, /* CRQB Gen-II/IIE HostQueTag shift */
CRQB_CMD_ADDR_SHIFT = 8,
CRQB_CMD_CS = (0x2 << 11),
CRQB_CMD_LAST = (1 << 15),
CRPB_FLAG_STATUS_SHIFT = 8,
+ CRPB_IOID_SHIFT_6 = 5, /* CRPB Gen-II IO Id shift */
+ CRPB_IOID_SHIFT_7 = 7, /* CRPB Gen-IIE IO Id shift */
EPRD_FLAG_END_OF_TBL = (1 << 31),
@@ -236,8 +233,10 @@ enum {
EDMA_ERR_DEV_DCON = (1 << 3),
EDMA_ERR_DEV_CON = (1 << 4),
EDMA_ERR_SERR = (1 << 5),
- EDMA_ERR_SELF_DIS = (1 << 7),
+ EDMA_ERR_SELF_DIS = (1 << 7), /* Gen II/IIE self-disable */
+ EDMA_ERR_SELF_DIS_5 = (1 << 8), /* Gen I self-disable */
EDMA_ERR_BIST_ASYNC = (1 << 8),
+ EDMA_ERR_TRANS_IRQ_7 = (1 << 8), /* Gen IIE transprt layer irq */
EDMA_ERR_CRBQ_PAR = (1 << 9),
EDMA_ERR_CRPB_PAR = (1 << 10),
EDMA_ERR_INTRL_PAR = (1 << 11),
@@ -248,13 +247,33 @@ enum {
EDMA_ERR_LNK_CTRL_TX = (0x1f << 21),
EDMA_ERR_LNK_DATA_TX = (0x1f << 26),
EDMA_ERR_TRANS_PROTO = (1 << 31),
- EDMA_ERR_FATAL = (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR |
- EDMA_ERR_DEV_DCON | EDMA_ERR_CRBQ_PAR |
- EDMA_ERR_CRPB_PAR | EDMA_ERR_INTRL_PAR |
- EDMA_ERR_IORDY | EDMA_ERR_LNK_CTRL_RX_2 |
- EDMA_ERR_LNK_DATA_RX |
- EDMA_ERR_LNK_DATA_TX |
- EDMA_ERR_TRANS_PROTO),
+ EDMA_ERR_OVERRUN_5 = (1 << 5),
+ EDMA_ERR_UNDERRUN_5 = (1 << 6),
+ EDMA_EH_FREEZE = EDMA_ERR_D_PAR |
+ EDMA_ERR_PRD_PAR |
+ EDMA_ERR_DEV_DCON |
+ EDMA_ERR_DEV_CON |
+ EDMA_ERR_SERR |
+ EDMA_ERR_SELF_DIS |
+ EDMA_ERR_CRBQ_PAR |
+ EDMA_ERR_CRPB_PAR |
+ EDMA_ERR_INTRL_PAR |
+ EDMA_ERR_IORDY |
+ EDMA_ERR_LNK_CTRL_RX_2 |
+ EDMA_ERR_LNK_DATA_RX |
+ EDMA_ERR_LNK_DATA_TX |
+ EDMA_ERR_TRANS_PROTO,
+ EDMA_EH_FREEZE_5 = EDMA_ERR_D_PAR |
+ EDMA_ERR_PRD_PAR |
+ EDMA_ERR_DEV_DCON |
+ EDMA_ERR_DEV_CON |
+ EDMA_ERR_OVERRUN_5 |
+ EDMA_ERR_UNDERRUN_5 |
+ EDMA_ERR_SELF_DIS_5 |
+ EDMA_ERR_CRBQ_PAR |
+ EDMA_ERR_CRPB_PAR |
+ EDMA_ERR_INTRL_PAR |
+ EDMA_ERR_IORDY,
EDMA_REQ_Q_BASE_HI_OFS = 0x10,
EDMA_REQ_Q_IN_PTR_OFS = 0x14, /* also contains BASE_LO */
@@ -282,18 +301,18 @@ enum {
MV_HP_ERRATA_60X1B2 = (1 << 3),
MV_HP_ERRATA_60X1C0 = (1 << 4),
MV_HP_ERRATA_XX42A0 = (1 << 5),
- MV_HP_50XX = (1 << 6),
- MV_HP_GEN_IIE = (1 << 7),
+ MV_HP_GEN_I = (1 << 6),
+ MV_HP_GEN_II = (1 << 7),
+ MV_HP_GEN_IIE = (1 << 8),
/* Port private flags (pp_flags) */
MV_PP_FLAG_EDMA_EN = (1 << 0),
MV_PP_FLAG_EDMA_DS_ACT = (1 << 1),
+ MV_PP_FLAG_HAD_A_RESET = (1 << 2),
};
-#define IS_50XX(hpriv) ((hpriv)->hp_flags & MV_HP_50XX)
-#define IS_60XX(hpriv) (((hpriv)->hp_flags & MV_HP_50XX) == 0)
-#define IS_GEN_I(hpriv) IS_50XX(hpriv)
-#define IS_GEN_II(hpriv) IS_60XX(hpriv)
+#define IS_GEN_I(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_I)
+#define IS_GEN_II(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_II)
#define IS_GEN_IIE(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_IIE)
enum {
@@ -352,6 +371,10 @@ struct mv_port_priv {
dma_addr_t crpb_dma;
struct mv_sg *sg_tbl;
dma_addr_t sg_tbl_dma;
+
+ unsigned int req_idx;
+ unsigned int resp_idx;
+
u32 pp_flags;
};
@@ -384,14 +407,15 @@ static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in);
static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
static u32 mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in);
static void mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
-static void mv_phy_reset(struct ata_port *ap);
-static void __mv_phy_reset(struct ata_port *ap, int can_sleep);
static int mv_port_start(struct ata_port *ap);
static void mv_port_stop(struct ata_port *ap);
static void mv_qc_prep(struct ata_queued_cmd *qc);
static void mv_qc_prep_iie(struct ata_queued_cmd *qc);
static unsigned int mv_qc_issue(struct ata_queued_cmd *qc);
-static void mv_eng_timeout(struct ata_port *ap);
+static void mv_error_handler(struct ata_port *ap);
+static void mv_post_int_cmd(struct ata_queued_cmd *qc);
+static void mv_eh_freeze(struct ata_port *ap);
+static void mv_eh_thaw(struct ata_port *ap);
static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
@@ -415,14 +439,31 @@ static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio);
static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio);
static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int port_no);
-static void mv_stop_and_reset(struct ata_port *ap);
-static struct scsi_host_template mv_sht = {
+static struct scsi_host_template mv5_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = MV_MAX_SG_CT,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = 1,
+ .proc_name = DRV_NAME,
+ .dma_boundary = MV_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
+ .bios_param = ata_std_bios_param,
+};
+
+static struct scsi_host_template mv6_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
- .can_queue = MV_USE_Q_DEPTH,
+ .can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = MV_MAX_SG_CT,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
@@ -444,19 +485,21 @@ static const struct ata_port_operations mv5_ops = {
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
- .phy_reset = mv_phy_reset,
.cable_detect = ata_cable_sata,
.qc_prep = mv_qc_prep,
.qc_issue = mv_qc_issue,
.data_xfer = ata_data_xfer,
- .eng_timeout = mv_eng_timeout,
-
.irq_clear = mv_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
+ .error_handler = mv_error_handler,
+ .post_internal_cmd = mv_post_int_cmd,
+ .freeze = mv_eh_freeze,
+ .thaw = mv_eh_thaw,
+
.scr_read = mv5_scr_read,
.scr_write = mv5_scr_write,
@@ -473,19 +516,21 @@ static const struct ata_port_operations mv6_ops = {
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
- .phy_reset = mv_phy_reset,
.cable_detect = ata_cable_sata,
.qc_prep = mv_qc_prep,
.qc_issue = mv_qc_issue,
.data_xfer = ata_data_xfer,
- .eng_timeout = mv_eng_timeout,
-
.irq_clear = mv_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
+ .error_handler = mv_error_handler,
+ .post_internal_cmd = mv_post_int_cmd,
+ .freeze = mv_eh_freeze,
+ .thaw = mv_eh_thaw,
+
.scr_read = mv_scr_read,
.scr_write = mv_scr_write,
@@ -502,19 +547,21 @@ static const struct ata_port_operations mv_iie_ops = {
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
- .phy_reset = mv_phy_reset,
.cable_detect = ata_cable_sata,
.qc_prep = mv_qc_prep_iie,
.qc_issue = mv_qc_issue,
.data_xfer = ata_data_xfer,
- .eng_timeout = mv_eng_timeout,
-
.irq_clear = mv_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
+ .error_handler = mv_error_handler,
+ .post_internal_cmd = mv_post_int_cmd,
+ .freeze = mv_eh_freeze,
+ .thaw = mv_eh_thaw,
+
.scr_read = mv_scr_read,
.scr_write = mv_scr_write,
@@ -530,38 +577,38 @@ static const struct ata_port_info mv_port_info[] = {
.port_ops = &mv5_ops,
},
{ /* chip_508x */
- .flags = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC),
+ .flags = MV_COMMON_FLAGS | MV_FLAG_DUAL_HC,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_5080 */
- .flags = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC),
+ .flags = MV_COMMON_FLAGS | MV_FLAG_DUAL_HC,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_604x */
- .flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS),
+ .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv6_ops,
},
{ /* chip_608x */
- .flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- MV_FLAG_DUAL_HC),
+ .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
+ MV_FLAG_DUAL_HC,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv6_ops,
},
{ /* chip_6042 */
- .flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS),
+ .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
{ /* chip_7042 */
- .flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS),
+ .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
@@ -709,6 +756,46 @@ static void mv_irq_clear(struct ata_port *ap)
{
}
+static void mv_set_edma_ptrs(void __iomem *port_mmio,
+ struct mv_host_priv *hpriv,
+ struct mv_port_priv *pp)
+{
+ u32 index;
+
+ /*
+ * initialize request queue
+ */
+ index = (pp->req_idx & MV_MAX_Q_DEPTH_MASK) << EDMA_REQ_Q_PTR_SHIFT;
+
+ WARN_ON(pp->crqb_dma & 0x3ff);
+ writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI_OFS);
+ writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | index,
+ port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
+
+ if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0)
+ writelfl((pp->crqb_dma & 0xffffffff) | index,
+ port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
+ else
+ writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
+
+ /*
+ * initialize response queue
+ */
+ index = (pp->resp_idx & MV_MAX_Q_DEPTH_MASK) << EDMA_RSP_Q_PTR_SHIFT;
+
+ WARN_ON(pp->crpb_dma & 0xff);
+ writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI_OFS);
+
+ if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0)
+ writelfl((pp->crpb_dma & 0xffffffff) | index,
+ port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
+ else
+ writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
+
+ writelfl((pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK) | index,
+ port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
+}
+
/**
* mv_start_dma - Enable eDMA engine
* @base: port base address
@@ -720,9 +807,15 @@ static void mv_irq_clear(struct ata_port *ap)
* LOCKING:
* Inherited from caller.
*/
-static void mv_start_dma(void __iomem *base, struct mv_port_priv *pp)
+static void mv_start_dma(void __iomem *base, struct mv_host_priv *hpriv,
+ struct mv_port_priv *pp)
{
- if (!(MV_PP_FLAG_EDMA_EN & pp->pp_flags)) {
+ if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN)) {
+ /* clear EDMA event indicators, if any */
+ writelfl(0, base + EDMA_ERR_IRQ_CAUSE_OFS);
+
+ mv_set_edma_ptrs(base, hpriv, pp);
+
writelfl(EDMA_EN, base + EDMA_CMD_OFS);
pp->pp_flags |= MV_PP_FLAG_EDMA_EN;
}
@@ -739,14 +832,14 @@ static void mv_start_dma(void __iomem *base, struct mv_port_priv *pp)
* LOCKING:
* Inherited from caller.
*/
-static void mv_stop_dma(struct ata_port *ap)
+static int mv_stop_dma(struct ata_port *ap)
{
void __iomem *port_mmio = mv_ap_base(ap);
struct mv_port_priv *pp = ap->private_data;
u32 reg;
- int i;
+ int i, err = 0;
- if (MV_PP_FLAG_EDMA_EN & pp->pp_flags) {
+ if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) {
/* Disable EDMA if active. The disable bit auto clears.
*/
writelfl(EDMA_DS, port_mmio + EDMA_CMD_OFS);
@@ -758,16 +851,18 @@ static void mv_stop_dma(struct ata_port *ap)
/* now properly wait for the eDMA to stop */
for (i = 1000; i > 0; i--) {
reg = readl(port_mmio + EDMA_CMD_OFS);
- if (!(EDMA_EN & reg)) {
+ if (!(reg & EDMA_EN))
break;
- }
+
udelay(100);
}
- if (EDMA_EN & reg) {
+ if (reg & EDMA_EN) {
ata_port_printk(ap, KERN_ERR, "Unable to stop eDMA\n");
- /* FIXME: Consider doing a reset here to recover */
+ err = -EIO;
}
+
+ return err;
}
#ifdef ATA_DEBUG
@@ -884,12 +979,13 @@ static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
writelfl(val, mv_ap_base(ap) + ofs);
}
-static void mv_edma_cfg(struct mv_host_priv *hpriv, void __iomem *port_mmio)
+static void mv_edma_cfg(struct ata_port *ap, struct mv_host_priv *hpriv,
+ void __iomem *port_mmio)
{
u32 cfg = readl(port_mmio + EDMA_CFG_OFS);
/* set up non-NCQ EDMA configuration */
- cfg &= ~(1 << 9); /* disable equeue */
+ cfg &= ~(1 << 9); /* disable eQue */
if (IS_GEN_I(hpriv)) {
cfg &= ~0x1f; /* clear queue depth */
@@ -909,7 +1005,7 @@ static void mv_edma_cfg(struct mv_host_priv *hpriv, void __iomem *port_mmio)
cfg |= (1 << 18); /* enab early completion */
cfg |= (1 << 17); /* enab cut-through (dis stor&forwrd) */
cfg &= ~(1 << 16); /* dis FIS-based switching (for now) */
- cfg &= ~(EDMA_CFG_NCQ | EDMA_CFG_NCQ_GO_ON_ERR); /* clear NCQ */
+ cfg &= ~(EDMA_CFG_NCQ); /* clear NCQ */
}
writelfl(cfg, port_mmio + EDMA_CFG_OFS);
@@ -971,28 +1067,9 @@ static int mv_port_start(struct ata_port *ap)
pp->sg_tbl = mem;
pp->sg_tbl_dma = mem_dma;
- mv_edma_cfg(hpriv, port_mmio);
+ mv_edma_cfg(ap, hpriv, port_mmio);
- writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI_OFS);
- writelfl(pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK,
- port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
-
- if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0)
- writelfl(pp->crqb_dma & 0xffffffff,
- port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
- else
- writelfl(0, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
-
- writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI_OFS);
-
- if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0)
- writelfl(pp->crpb_dma & 0xffffffff,
- port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
- else
- writelfl(0, port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
-
- writelfl(pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK,
- port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
+ mv_set_edma_ptrs(port_mmio, hpriv, pp);
/* Don't turn on EDMA here...do it before DMA commands only. Else
* we'll be unable to send non-data, PIO, etc due to restricted access
@@ -1055,11 +1132,6 @@ static unsigned int mv_fill_sg(struct ata_queued_cmd *qc)
return n_sg;
}
-static inline unsigned mv_inc_q_index(unsigned index)
-{
- return (index + 1) & MV_MAX_Q_DEPTH_MASK;
-}
-
static inline void mv_crqb_pack_cmd(__le16 *cmdw, u8 data, u8 addr, unsigned last)
{
u16 tmp = data | (addr << CRQB_CMD_ADDR_SHIFT) | CRQB_CMD_CS |
@@ -1088,7 +1160,7 @@ static void mv_qc_prep(struct ata_queued_cmd *qc)
u16 flags = 0;
unsigned in_index;
- if (ATA_PROT_DMA != qc->tf.protocol)
+ if (qc->tf.protocol != ATA_PROT_DMA)
return;
/* Fill in command request block
@@ -1097,10 +1169,10 @@ static void mv_qc_prep(struct ata_queued_cmd *qc)
flags |= CRQB_FLAG_READ;
WARN_ON(MV_MAX_Q_DEPTH <= qc->tag);
flags |= qc->tag << CRQB_TAG_SHIFT;
+ flags |= qc->tag << CRQB_IOID_SHIFT; /* 50xx appears to ignore this*/
- /* get current queue index from hardware */
- in_index = (readl(mv_ap_base(ap) + EDMA_REQ_Q_IN_PTR_OFS)
- >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
+ /* get current queue index from software */
+ in_index = pp->req_idx & MV_MAX_Q_DEPTH_MASK;
pp->crqb[in_index].sg_addr =
cpu_to_le32(pp->sg_tbl_dma & 0xffffffff);
@@ -1180,7 +1252,7 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc)
unsigned in_index;
u32 flags = 0;
- if (ATA_PROT_DMA != qc->tf.protocol)
+ if (qc->tf.protocol != ATA_PROT_DMA)
return;
/* Fill in Gen IIE command request block
@@ -1190,10 +1262,11 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc)
WARN_ON(MV_MAX_Q_DEPTH <= qc->tag);
flags |= qc->tag << CRQB_TAG_SHIFT;
+ flags |= qc->tag << CRQB_IOID_SHIFT; /* "I/O Id" is -really-
+ what we use as our tag */
- /* get current queue index from hardware */
- in_index = (readl(mv_ap_base(ap) + EDMA_REQ_Q_IN_PTR_OFS)
- >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
+ /* get current queue index from software */
+ in_index = pp->req_idx & MV_MAX_Q_DEPTH_MASK;
crqb = (struct mv_crqb_iie *) &pp->crqb[in_index];
crqb->addr = cpu_to_le32(pp->sg_tbl_dma & 0xffffffff);
@@ -1241,83 +1314,41 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc)
*/
static unsigned int mv_qc_issue(struct ata_queued_cmd *qc)
{
- void __iomem *port_mmio = mv_ap_base(qc->ap);
- struct mv_port_priv *pp = qc->ap->private_data;
- unsigned in_index;
- u32 in_ptr;
+ struct ata_port *ap = qc->ap;
+ void __iomem *port_mmio = mv_ap_base(ap);
+ struct mv_port_priv *pp = ap->private_data;
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ u32 in_index;
- if (ATA_PROT_DMA != qc->tf.protocol) {
+ if (qc->tf.protocol != ATA_PROT_DMA) {
/* We're about to send a non-EDMA capable command to the
* port. Turn off EDMA so there won't be problems accessing
* shadow block, etc registers.
*/
- mv_stop_dma(qc->ap);
+ mv_stop_dma(ap);
return ata_qc_issue_prot(qc);
}
- in_ptr = readl(port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
- in_index = (in_ptr >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
+ mv_start_dma(port_mmio, hpriv, pp);
+
+ in_index = pp->req_idx & MV_MAX_Q_DEPTH_MASK;
/* until we do queuing, the queue should be empty at this point */
WARN_ON(in_index != ((readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS)
>> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK));
- in_index = mv_inc_q_index(in_index); /* now incr producer index */
+ pp->req_idx++;
- mv_start_dma(port_mmio, pp);
+ in_index = (pp->req_idx & MV_MAX_Q_DEPTH_MASK) << EDMA_REQ_Q_PTR_SHIFT;
/* and write the request in pointer to kick the EDMA to life */
- in_ptr &= EDMA_REQ_Q_BASE_LO_MASK;
- in_ptr |= in_index << EDMA_REQ_Q_PTR_SHIFT;
- writelfl(in_ptr, port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
+ writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | in_index,
+ port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
return 0;
}
/**
- * mv_get_crpb_status - get status from most recently completed cmd
- * @ap: ATA channel to manipulate
- *
- * This routine is for use when the port is in DMA mode, when it
- * will be using the CRPB (command response block) method of
- * returning command completion information. We check indices
- * are good, grab status, and bump the response consumer index to
- * prove that we're up to date.
- *
- * LOCKING:
- * Inherited from caller.
- */
-static u8 mv_get_crpb_status(struct ata_port *ap)
-{
- void __iomem *port_mmio = mv_ap_base(ap);
- struct mv_port_priv *pp = ap->private_data;
- unsigned out_index;
- u32 out_ptr;
- u8 ata_status;
-
- out_ptr = readl(port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
- out_index = (out_ptr >> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
-
- ata_status = le16_to_cpu(pp->crpb[out_index].flags)
- >> CRPB_FLAG_STATUS_SHIFT;
-
- /* increment our consumer index... */
- out_index = mv_inc_q_index(out_index);
-
- /* and, until we do NCQ, there should only be 1 CRPB waiting */
- WARN_ON(out_index != ((readl(port_mmio + EDMA_RSP_Q_IN_PTR_OFS)
- >> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK));
-
- /* write out our inc'd consumer index so EDMA knows we're caught up */
- out_ptr &= EDMA_RSP_Q_BASE_LO_MASK;
- out_ptr |= out_index << EDMA_RSP_Q_PTR_SHIFT;
- writelfl(out_ptr, port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
-
- /* Return ATA status register for completed CRPB */
- return ata_status;
-}
-
-/**
* mv_err_intr - Handle error interrupts on the port
* @ap: ATA channel to manipulate
* @reset_allowed: bool: 0 == don't trigger from reset here
@@ -1331,30 +1362,191 @@ static u8 mv_get_crpb_status(struct ata_port *ap)
* LOCKING:
* Inherited from caller.
*/
-static void mv_err_intr(struct ata_port *ap, int reset_allowed)
+static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
{
void __iomem *port_mmio = mv_ap_base(ap);
- u32 edma_err_cause, serr = 0;
+ u32 edma_err_cause, eh_freeze_mask, serr = 0;
+ struct mv_port_priv *pp = ap->private_data;
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ unsigned int edma_enabled = (pp->pp_flags & MV_PP_FLAG_EDMA_EN);
+ unsigned int action = 0, err_mask = 0;
+ struct ata_eh_info *ehi = &ap->eh_info;
- edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+ ata_ehi_clear_desc(ehi);
- if (EDMA_ERR_SERR & edma_err_cause) {
+ if (!edma_enabled) {
+ /* just a guess: do we need to do this? should we
+ * expand this, and do it in all cases?
+ */
sata_scr_read(ap, SCR_ERROR, &serr);
sata_scr_write_flush(ap, SCR_ERROR, serr);
}
- if (EDMA_ERR_SELF_DIS & edma_err_cause) {
- struct mv_port_priv *pp = ap->private_data;
- pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
+
+ edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+
+ ata_ehi_push_desc(ehi, "edma_err 0x%08x", edma_err_cause);
+
+ /*
+ * all generations share these EDMA error cause bits
+ */
+
+ if (edma_err_cause & EDMA_ERR_DEV)
+ err_mask |= AC_ERR_DEV;
+ if (edma_err_cause & (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR |
+ EDMA_ERR_CRBQ_PAR | EDMA_ERR_CRPB_PAR |
+ EDMA_ERR_INTRL_PAR)) {
+ err_mask |= AC_ERR_ATA_BUS;
+ action |= ATA_EH_HARDRESET;
+ ata_ehi_push_desc(ehi, ", parity error");
+ }
+ if (edma_err_cause & (EDMA_ERR_DEV_DCON | EDMA_ERR_DEV_CON)) {
+ ata_ehi_hotplugged(ehi);
+ ata_ehi_push_desc(ehi, edma_err_cause & EDMA_ERR_DEV_DCON ?
+ ", dev disconnect" : ", dev connect");
+ }
+
+ if (IS_GEN_I(hpriv)) {
+ eh_freeze_mask = EDMA_EH_FREEZE_5;
+
+ if (edma_err_cause & EDMA_ERR_SELF_DIS_5) {
+ struct mv_port_priv *pp = ap->private_data;
+ pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
+ ata_ehi_push_desc(ehi, ", EDMA self-disable");
+ }
+ } else {
+ eh_freeze_mask = EDMA_EH_FREEZE;
+
+ if (edma_err_cause & EDMA_ERR_SELF_DIS) {
+ struct mv_port_priv *pp = ap->private_data;
+ pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
+ ata_ehi_push_desc(ehi, ", EDMA self-disable");
+ }
+
+ if (edma_err_cause & EDMA_ERR_SERR) {
+ sata_scr_read(ap, SCR_ERROR, &serr);
+ sata_scr_write_flush(ap, SCR_ERROR, serr);
+ err_mask = AC_ERR_ATA_BUS;
+ action |= ATA_EH_HARDRESET;
+ }
}
- DPRINTK(KERN_ERR "ata%u: port error; EDMA err cause: 0x%08x "
- "SERR: 0x%08x\n", ap->print_id, edma_err_cause, serr);
/* Clear EDMA now that SERR cleanup done */
writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
- /* check for fatal here and recover if needed */
- if (reset_allowed && (EDMA_ERR_FATAL & edma_err_cause))
- mv_stop_and_reset(ap);
+ if (!err_mask) {
+ err_mask = AC_ERR_OTHER;
+ action |= ATA_EH_HARDRESET;
+ }
+
+ ehi->serror |= serr;
+ ehi->action |= action;
+
+ if (qc)
+ qc->err_mask |= err_mask;
+ else
+ ehi->err_mask |= err_mask;
+
+ if (edma_err_cause & eh_freeze_mask)
+ ata_port_freeze(ap);
+ else
+ ata_port_abort(ap);
+}
+
+static void mv_intr_pio(struct ata_port *ap)
+{
+ struct ata_queued_cmd *qc;
+ u8 ata_status;
+
+ /* ignore spurious intr if drive still BUSY */
+ ata_status = readb(ap->ioaddr.status_addr);
+ if (unlikely(ata_status & ATA_BUSY))
+ return;
+
+ /* get active ATA command */
+ qc = ata_qc_from_tag(ap, ap->active_tag);
+ if (unlikely(!qc)) /* no active tag */
+ return;
+ if (qc->tf.flags & ATA_TFLAG_POLLING) /* polling; we don't own qc */
+ return;
+
+ /* and finally, complete the ATA command */
+ qc->err_mask |= ac_err_mask(ata_status);
+ ata_qc_complete(qc);
+}
+
+static void mv_intr_edma(struct ata_port *ap)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ struct mv_port_priv *pp = ap->private_data;
+ struct ata_queued_cmd *qc;
+ u32 out_index, in_index;
+ bool work_done = false;
+
+ /* get h/w response queue pointer */
+ in_index = (readl(port_mmio + EDMA_RSP_Q_IN_PTR_OFS)
+ >> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
+
+ while (1) {
+ u16 status;
+
+ /* get s/w response queue last-read pointer, and compare */
+ out_index = pp->resp_idx & MV_MAX_Q_DEPTH_MASK;
+ if (in_index == out_index)
+ break;
+
+
+ /* 50xx: get active ATA command */
+ if (IS_GEN_I(hpriv))
+ qc = ata_qc_from_tag(ap, ap->active_tag);
+
+ /* 60xx: get active ATA command via tag, to enable support
+ * for queueing. this works transparently for queued and
+ * non-queued modes.
+ */
+ else {
+ unsigned int tag;
+
+ if (IS_GEN_II(hpriv))
+ tag = (le16_to_cpu(pp->crpb[out_index].id)
+ >> CRPB_IOID_SHIFT_6) & 0x3f;
+ else
+ tag = (le16_to_cpu(pp->crpb[out_index].id)
+ >> CRPB_IOID_SHIFT_7) & 0x3f;
+
+ qc = ata_qc_from_tag(ap, tag);
+ }
+
+ /* lower 8 bits of status are EDMA_ERR_IRQ_CAUSE_OFS
+ * bits (WARNING: might not necessarily be associated
+ * with this command), which -should- be clear
+ * if all is well
+ */
+ status = le16_to_cpu(pp->crpb[out_index].flags);
+ if (unlikely(status & 0xff)) {
+ mv_err_intr(ap, qc);
+ return;
+ }
+
+ /* and finally, complete the ATA command */
+ if (qc) {
+ qc->err_mask |=
+ ac_err_mask(status >> CRPB_FLAG_STATUS_SHIFT);
+ ata_qc_complete(qc);
+ }
+
+ /* advance software response queue pointer, to
+ * indicate (after the loop completes) to hardware
+ * that we have consumed a response queue entry.
+ */
+ work_done = true;
+ pp->resp_idx++;
+ }
+
+ if (work_done)
+ writelfl((pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK) |
+ (out_index << EDMA_RSP_Q_PTR_SHIFT),
+ port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
}
/**
@@ -1377,10 +1569,8 @@ static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc)
{
void __iomem *mmio = host->iomap[MV_PRIMARY_BAR];
void __iomem *hc_mmio = mv_hc_base(mmio, hc);
- struct ata_queued_cmd *qc;
u32 hc_irq_cause;
- int shift, port, port0, hard_port, handled;
- unsigned int err_mask;
+ int port, port0;
if (hc == 0)
port0 = 0;
@@ -1389,79 +1579,95 @@ static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc)
/* we'll need the HC success int register in most cases */
hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
- if (hc_irq_cause)
- writelfl(~hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
+ if (!hc_irq_cause)
+ return;
+
+ writelfl(~hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
VPRINTK("ENTER, hc%u relevant=0x%08x HC IRQ cause=0x%08x\n",
hc,relevant,hc_irq_cause);
for (port = port0; port < port0 + MV_PORTS_PER_HC; port++) {
- u8 ata_status = 0;
struct ata_port *ap = host->ports[port];
struct mv_port_priv *pp = ap->private_data;
+ int have_err_bits, hard_port, shift;
+
+ if ((!ap) || (ap->flags & ATA_FLAG_DISABLED))
+ continue;
+
+ shift = port << 1; /* (port * 2) */
+ if (port >= MV_PORTS_PER_HC) {
+ shift++; /* skip bit 8 in the HC Main IRQ reg */
+ }
+ have_err_bits = ((PORT0_ERR << shift) & relevant);
+
+ if (unlikely(have_err_bits)) {
+ struct ata_queued_cmd *qc;
+
+ qc = ata_qc_from_tag(ap, ap->active_tag);
+ if (qc && (qc->tf.flags & ATA_TFLAG_POLLING))
+ continue;
+
+ mv_err_intr(ap, qc);
+ continue;
+ }
hard_port = mv_hardport_from_port(port); /* range 0..3 */
- handled = 0; /* ensure ata_status is set if handled++ */
- /* Note that DEV_IRQ might happen spuriously during EDMA,
- * and should be ignored in such cases.
- * The cause of this is still under investigation.
- */
if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) {
- /* EDMA: check for response queue interrupt */
- if ((CRPB_DMA_DONE << hard_port) & hc_irq_cause) {
- ata_status = mv_get_crpb_status(ap);
- handled = 1;
- }
+ if ((CRPB_DMA_DONE << hard_port) & hc_irq_cause)
+ mv_intr_edma(ap);
} else {
- /* PIO: check for device (drive) interrupt */
- if ((DEV_IRQ << hard_port) & hc_irq_cause) {
- ata_status = readb(ap->ioaddr.status_addr);
- handled = 1;
- /* ignore spurious intr if drive still BUSY */
- if (ata_status & ATA_BUSY) {
- ata_status = 0;
- handled = 0;
- }
- }
+ if ((DEV_IRQ << hard_port) & hc_irq_cause)
+ mv_intr_pio(ap);
}
+ }
+ VPRINTK("EXIT\n");
+}
- if (ap && (ap->flags & ATA_FLAG_DISABLED))
- continue;
+static void mv_pci_error(struct ata_host *host, void __iomem *mmio)
+{
+ struct ata_port *ap;
+ struct ata_queued_cmd *qc;
+ struct ata_eh_info *ehi;
+ unsigned int i, err_mask, printed = 0;
+ u32 err_cause;
- err_mask = ac_err_mask(ata_status);
+ err_cause = readl(mmio + PCI_IRQ_CAUSE_OFS);
- shift = port << 1; /* (port * 2) */
- if (port >= MV_PORTS_PER_HC) {
- shift++; /* skip bit 8 in the HC Main IRQ reg */
- }
- if ((PORT0_ERR << shift) & relevant) {
- mv_err_intr(ap, 1);
- err_mask |= AC_ERR_OTHER;
- handled = 1;
- }
+ dev_printk(KERN_ERR, host->dev, "PCI ERROR; PCI IRQ cause=0x%08x\n",
+ err_cause);
+
+ DPRINTK("All regs @ PCI error\n");
+ mv_dump_all_regs(mmio, -1, to_pci_dev(host->dev));
+
+ writelfl(0, mmio + PCI_IRQ_CAUSE_OFS);
- if (handled) {
+ for (i = 0; i < host->n_ports; i++) {
+ ap = host->ports[i];
+ if (!ata_port_offline(ap)) {
+ ehi = &ap->eh_info;
+ ata_ehi_clear_desc(ehi);
+ if (!printed++)
+ ata_ehi_push_desc(ehi,
+ "PCI err cause 0x%08x", err_cause);
+ err_mask = AC_ERR_HOST_BUS;
+ ehi->action = ATA_EH_HARDRESET;
qc = ata_qc_from_tag(ap, ap->active_tag);
- if (qc && (qc->flags & ATA_QCFLAG_ACTIVE)) {
- VPRINTK("port %u IRQ found for qc, "
- "ata_status 0x%x\n", port,ata_status);
- /* mark qc status appropriately */
- if (!(qc->tf.flags & ATA_TFLAG_POLLING)) {
- qc->err_mask |= err_mask;
- ata_qc_complete(qc);
- }
- }
+ if (qc)
+ qc->err_mask |= err_mask;
+ else
+ ehi->err_mask |= err_mask;
+
+ ata_port_freeze(ap);
}
}
- VPRINTK("EXIT\n");
}
/**
- * mv_interrupt -
+ * mv_interrupt - Main interrupt event handler
* @irq: unused
* @dev_instance: private data; in this case the host structure
- * @regs: unused
*
* Read the read only register to determine if any host
* controllers have pending interrupts. If so, call lower level
@@ -1477,7 +1683,6 @@ static irqreturn_t mv_interrupt(int irq, void *dev_instance)
struct ata_host *host = dev_instance;
unsigned int hc, handled = 0, n_hcs;
void __iomem *mmio = host->iomap[MV_PRIMARY_BAR];
- struct mv_host_priv *hpriv;
u32 irq_stat;
irq_stat = readl(mmio + HC_MAIN_IRQ_CAUSE_OFS);
@@ -1491,34 +1696,21 @@ static irqreturn_t mv_interrupt(int irq, void *dev_instance)
n_hcs = mv_get_hc_count(host->ports[0]->flags);
spin_lock(&host->lock);
+ if (unlikely(irq_stat & PCI_ERR)) {
+ mv_pci_error(host, mmio);
+ handled = 1;
+ goto out_unlock; /* skip all other HC irq handling */
+ }
+
for (hc = 0; hc < n_hcs; hc++) {
u32 relevant = irq_stat & (HC0_IRQ_PEND << (hc * HC_SHIFT));
if (relevant) {
mv_host_intr(host, relevant, hc);
- handled++;
- }
- }
-
- hpriv = host->private_data;
- if (IS_60XX(hpriv)) {
- /* deal with the interrupt coalescing bits */
- if (irq_stat & (TRAN_LO_DONE | TRAN_HI_DONE | PORTS_0_7_COAL_DONE)) {
- writelfl(0, mmio + MV_IRQ_COAL_CAUSE_LO);
- writelfl(0, mmio + MV_IRQ_COAL_CAUSE_HI);
- writelfl(0, mmio + MV_IRQ_COAL_CAUSE);
+ handled = 1;
}
}
- if (PCI_ERR & irq_stat) {
- printk(KERN_ERR DRV_NAME ": PCI ERROR; PCI IRQ cause=0x%08x\n",
- readl(mmio + PCI_IRQ_CAUSE_OFS));
-
- DPRINTK("All regs @ PCI error\n");
- mv_dump_all_regs(mmio, -1, to_pci_dev(host->dev));
-
- writelfl(0, mmio + PCI_IRQ_CAUSE_OFS);
- handled++;
- }
+out_unlock:
spin_unlock(&host->lock);
return IRQ_RETVAL(handled);
@@ -1907,7 +2099,7 @@ static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio,
writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS);
- if (IS_60XX(hpriv)) {
+ if (IS_GEN_II(hpriv)) {
u32 ifctl = readl(port_mmio + SATA_INTERFACE_CTL);
ifctl |= (1 << 7); /* enable gen2i speed */
ifctl = (ifctl & 0xfff) | 0x9b1000; /* from chip spec */
@@ -1923,32 +2115,12 @@ static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio,
hpriv->ops->phy_errata(hpriv, mmio, port_no);
- if (IS_50XX(hpriv))
+ if (IS_GEN_I(hpriv))
mdelay(1);
}
-static void mv_stop_and_reset(struct ata_port *ap)
-{
- struct mv_host_priv *hpriv = ap->host->private_data;
- void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
-
- mv_stop_dma(ap);
-
- mv_channel_reset(hpriv, mmio, ap->port_no);
-
- __mv_phy_reset(ap, 0);
-}
-
-static inline void __msleep(unsigned int msec, int can_sleep)
-{
- if (can_sleep)
- msleep(msec);
- else
- mdelay(msec);
-}
-
/**
- * __mv_phy_reset - Perform eDMA reset followed by COMRESET
+ * mv_phy_reset - Perform eDMA reset followed by COMRESET
* @ap: ATA channel to manipulate
*
* Part of this is taken from __sata_phy_reset and modified to
@@ -1958,14 +2130,12 @@ static inline void __msleep(unsigned int msec, int can_sleep)
* Inherited from caller. This is coded to safe to call at
* interrupt level, i.e. it does not sleep.
*/
-static void __mv_phy_reset(struct ata_port *ap, int can_sleep)
+static void mv_phy_reset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
{
struct mv_port_priv *pp = ap->private_data;
struct mv_host_priv *hpriv = ap->host->private_data;
void __iomem *port_mmio = mv_ap_base(ap);
- struct ata_taskfile tf;
- struct ata_device *dev = &ap->device[0];
- unsigned long timeout;
int retry = 5;
u32 sstatus;
@@ -1978,22 +2148,21 @@ static void __mv_phy_reset(struct ata_port *ap, int can_sleep)
/* Issue COMRESET via SControl */
comreset_retry:
sata_scr_write_flush(ap, SCR_CONTROL, 0x301);
- __msleep(1, can_sleep);
+ msleep(1);
sata_scr_write_flush(ap, SCR_CONTROL, 0x300);
- __msleep(20, can_sleep);
+ msleep(20);
- timeout = jiffies + msecs_to_jiffies(200);
do {
sata_scr_read(ap, SCR_STATUS, &sstatus);
if (((sstatus & 0x3) == 3) || ((sstatus & 0x3) == 0))
break;
- __msleep(1, can_sleep);
- } while (time_before(jiffies, timeout));
+ msleep(1);
+ } while (time_before(jiffies, deadline));
/* work around errata */
- if (IS_60XX(hpriv) &&
+ if (IS_GEN_II(hpriv) &&
(sstatus != 0x0) && (sstatus != 0x113) && (sstatus != 0x123) &&
(retry-- > 0))
goto comreset_retry;
@@ -2002,13 +2171,8 @@ comreset_retry:
"SCtrl 0x%08x\n", mv_scr_read(ap, SCR_STATUS),
mv_scr_read(ap, SCR_ERROR), mv_scr_read(ap, SCR_CONTROL));
- if (ata_port_online(ap)) {
- ata_port_probe(ap);
- } else {
- sata_scr_read(ap, SCR_STATUS, &sstatus);
- ata_port_printk(ap, KERN_INFO,
- "no device found (phy stat %08x)\n", sstatus);
- ata_port_disable(ap);
+ if (ata_port_offline(ap)) {
+ *class = ATA_DEV_NONE;
return;
}
@@ -2022,68 +2186,152 @@ comreset_retry:
u8 drv_stat = ata_check_status(ap);
if ((drv_stat != 0x80) && (drv_stat != 0x7f))
break;
- __msleep(500, can_sleep);
+ msleep(500);
if (retry-- <= 0)
break;
+ if (time_after(jiffies, deadline))
+ break;
}
- tf.lbah = readb(ap->ioaddr.lbah_addr);
- tf.lbam = readb(ap->ioaddr.lbam_addr);
- tf.lbal = readb(ap->ioaddr.lbal_addr);
- tf.nsect = readb(ap->ioaddr.nsect_addr);
+ /* FIXME: if we passed the deadline, the following
+ * code probably produces an invalid result
+ */
- dev->class = ata_dev_classify(&tf);
- if (!ata_dev_enabled(dev)) {
- VPRINTK("Port disabled post-sig: No device present.\n");
- ata_port_disable(ap);
- }
+ /* finally, read device signature from TF registers */
+ *class = ata_dev_try_classify(ap, 0, NULL);
writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
- pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
+ WARN_ON(pp->pp_flags & MV_PP_FLAG_EDMA_EN);
VPRINTK("EXIT\n");
}
-static void mv_phy_reset(struct ata_port *ap)
+static int mv_prereset(struct ata_port *ap, unsigned long deadline)
{
- __mv_phy_reset(ap, 1);
+ struct mv_port_priv *pp = ap->private_data;
+ struct ata_eh_context *ehc = &ap->eh_context;
+ int rc;
+
+ rc = mv_stop_dma(ap);
+ if (rc)
+ ehc->i.action |= ATA_EH_HARDRESET;
+
+ if (!(pp->pp_flags & MV_PP_FLAG_HAD_A_RESET)) {
+ pp->pp_flags |= MV_PP_FLAG_HAD_A_RESET;
+ ehc->i.action |= ATA_EH_HARDRESET;
+ }
+
+ /* if we're about to do hardreset, nothing more to do */
+ if (ehc->i.action & ATA_EH_HARDRESET)
+ return 0;
+
+ if (ata_port_online(ap))
+ rc = ata_wait_ready(ap, deadline);
+ else
+ rc = -ENODEV;
+
+ return rc;
}
-/**
- * mv_eng_timeout - Routine called by libata when SCSI times out I/O
- * @ap: ATA channel to manipulate
- *
- * Intent is to clear all pending error conditions, reset the
- * chip/bus, fail the command, and move on.
- *
- * LOCKING:
- * This routine holds the host lock while failing the command.
- */
-static void mv_eng_timeout(struct ata_port *ap)
+static int mv_hardreset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
{
+ struct mv_host_priv *hpriv = ap->host->private_data;
void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
- struct ata_queued_cmd *qc;
- unsigned long flags;
- ata_port_printk(ap, KERN_ERR, "Entering mv_eng_timeout\n");
- DPRINTK("All regs @ start of eng_timeout\n");
- mv_dump_all_regs(mmio, ap->port_no, to_pci_dev(ap->host->dev));
+ mv_stop_dma(ap);
- qc = ata_qc_from_tag(ap, ap->active_tag);
- printk(KERN_ERR "mmio_base %p ap %p qc %p scsi_cmnd %p &cmnd %p\n",
- mmio, ap, qc, qc->scsicmd, &qc->scsicmd->cmnd);
+ mv_channel_reset(hpriv, mmio, ap->port_no);
- spin_lock_irqsave(&ap->host->lock, flags);
- mv_err_intr(ap, 0);
- mv_stop_and_reset(ap);
- spin_unlock_irqrestore(&ap->host->lock, flags);
+ mv_phy_reset(ap, class, deadline);
+
+ return 0;
+}
+
+static void mv_postreset(struct ata_port *ap, unsigned int *classes)
+{
+ u32 serr;
+
+ /* print link status */
+ sata_print_link_status(ap);
+
+ /* clear SError */
+ sata_scr_read(ap, SCR_ERROR, &serr);
+ sata_scr_write_flush(ap, SCR_ERROR, serr);
- WARN_ON(!(qc->flags & ATA_QCFLAG_ACTIVE));
- if (qc->flags & ATA_QCFLAG_ACTIVE) {
- qc->err_mask |= AC_ERR_TIMEOUT;
- ata_eh_qc_complete(qc);
+ /* bail out if no device is present */
+ if (classes[0] == ATA_DEV_NONE && classes[1] == ATA_DEV_NONE) {
+ DPRINTK("EXIT, no device\n");
+ return;
}
+
+ /* set up device control */
+ iowrite8(ap->ctl, ap->ioaddr.ctl_addr);
+}
+
+static void mv_error_handler(struct ata_port *ap)
+{
+ ata_do_eh(ap, mv_prereset, ata_std_softreset,
+ mv_hardreset, mv_postreset);
+}
+
+static void mv_post_int_cmd(struct ata_queued_cmd *qc)
+{
+ mv_stop_dma(qc->ap);
+}
+
+static void mv_eh_freeze(struct ata_port *ap)
+{
+ void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ unsigned int hc = (ap->port_no > 3) ? 1 : 0;
+ u32 tmp, mask;
+ unsigned int shift;
+
+ /* FIXME: handle coalescing completion events properly */
+
+ shift = ap->port_no * 2;
+ if (hc > 0)
+ shift++;
+
+ mask = 0x3 << shift;
+
+ /* disable assertion of portN err, done events */
+ tmp = readl(mmio + HC_MAIN_IRQ_MASK_OFS);
+ writelfl(tmp & ~mask, mmio + HC_MAIN_IRQ_MASK_OFS);
+}
+
+static void mv_eh_thaw(struct ata_port *ap)
+{
+ void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ unsigned int hc = (ap->port_no > 3) ? 1 : 0;
+ void __iomem *hc_mmio = mv_hc_base(mmio, hc);
+ void __iomem *port_mmio = mv_ap_base(ap);
+ u32 tmp, mask, hc_irq_cause;
+ unsigned int shift, hc_port_no = ap->port_no;
+
+ /* FIXME: handle coalescing completion events properly */
+
+ shift = ap->port_no * 2;
+ if (hc > 0) {
+ shift++;
+ hc_port_no -= 4;
+ }
+
+ mask = 0x3 << shift;
+
+ /* clear EDMA errors on this port */
+ writel(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+
+ /* clear pending irq events */
+ hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
+ hc_irq_cause &= ~(1 << hc_port_no); /* clear CRPB-done */
+ hc_irq_cause &= ~(1 << (hc_port_no + 8)); /* clear Device int */
+ writel(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
+
+ /* enable assertion of portN err, done events */
+ tmp = readl(mmio + HC_MAIN_IRQ_MASK_OFS);
+ writelfl(tmp | mask, mmio + HC_MAIN_IRQ_MASK_OFS);
}
/**
@@ -2147,7 +2395,7 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
switch(board_idx) {
case chip_5080:
hpriv->ops = &mv5xxx_ops;
- hp_flags |= MV_HP_50XX;
+ hp_flags |= MV_HP_GEN_I;
switch (rev_id) {
case 0x1:
@@ -2167,7 +2415,7 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
case chip_504x:
case chip_508x:
hpriv->ops = &mv5xxx_ops;
- hp_flags |= MV_HP_50XX;
+ hp_flags |= MV_HP_GEN_I;
switch (rev_id) {
case 0x0:
@@ -2187,6 +2435,7 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
case chip_604x:
case chip_608x:
hpriv->ops = &mv6xxx_ops;
+ hp_flags |= MV_HP_GEN_II;
switch (rev_id) {
case 0x7:
@@ -2206,7 +2455,6 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
case chip_7042:
case chip_6042:
hpriv->ops = &mv6xxx_ops;
-
hp_flags |= MV_HP_GEN_IIE;
switch (rev_id) {
@@ -2273,7 +2521,7 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
hpriv->ops->enable_leds(hpriv, mmio);
for (port = 0; port < host->n_ports; port++) {
- if (IS_60XX(hpriv)) {
+ if (IS_GEN_II(hpriv)) {
void __iomem *port_mmio = mv_port_base(mmio, port);
u32 ifctl = readl(port_mmio + SATA_INTERFACE_CTL);
@@ -2308,7 +2556,7 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
/* and unmask interrupt generation for host regs */
writelfl(PCI_UNMASK_ALL_IRQS, mmio + PCI_IRQ_MASK_OFS);
- if (IS_50XX(hpriv))
+ if (IS_GEN_I(hpriv))
writelfl(~HC_MAIN_MASKED_IRQS_5, mmio + HC_MAIN_IRQ_MASK_OFS);
else
writelfl(~HC_MAIN_MASKED_IRQS, mmio + HC_MAIN_IRQ_MASK_OFS);
@@ -2426,8 +2674,9 @@ static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
mv_print_info(host);
pci_set_master(pdev);
+ pci_set_mwi(pdev);
return ata_host_activate(host, pdev->irq, mv_interrupt, IRQF_SHARED,
- &mv_sht);
+ IS_GEN_I(hpriv) ? &mv5_sht : &mv6_sht);
}
static int __init mv_init(void)
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index b265686..db81e3e 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -1560,7 +1560,7 @@ static int nv_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
}
ppi[0] = &nv_port_info[type];
- rc = ata_pci_prepare_native_host(pdev, ppi, &host);
+ rc = ata_pci_prepare_sff_host(pdev, ppi, &host);
if (rc)
return rc;
diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c
index 2ad5872..d2fcb9a 100644
--- a/drivers/ata/sata_promise.c
+++ b/drivers/ata/sata_promise.c
@@ -45,7 +45,7 @@
#include "sata_promise.h"
#define DRV_NAME "sata_promise"
-#define DRV_VERSION "2.08"
+#define DRV_VERSION "2.09"
enum {
PDC_MAX_PORTS = 4,
@@ -716,6 +716,9 @@ static irqreturn_t pdc_interrupt (int irq, void *dev_instance)
unsigned int i, tmp;
unsigned int handled = 0;
void __iomem *mmio_base;
+ unsigned int hotplug_offset, ata_no;
+ u32 hotplug_status;
+ int is_sataii_tx4;
VPRINTK("ENTER\n");
@@ -726,10 +729,20 @@ static irqreturn_t pdc_interrupt (int irq, void *dev_instance)
mmio_base = host->iomap[PDC_MMIO_BAR];
+ /* read and clear hotplug flags for all ports */
+ if (host->ports[0]->flags & PDC_FLAG_GEN_II)
+ hotplug_offset = PDC2_SATA_PLUG_CSR;
+ else
+ hotplug_offset = PDC_SATA_PLUG_CSR;
+ hotplug_status = readl(mmio_base + hotplug_offset);
+ if (hotplug_status & 0xff)
+ writel(hotplug_status | 0xff, mmio_base + hotplug_offset);
+ hotplug_status &= 0xff; /* clear uninteresting bits */
+
/* reading should also clear interrupts */
mask = readl(mmio_base + PDC_INT_SEQMASK);
- if (mask == 0xffffffff) {
+ if (mask == 0xffffffff && hotplug_status == 0) {
VPRINTK("QUICK EXIT 2\n");
return IRQ_NONE;
}
@@ -737,16 +750,34 @@ static irqreturn_t pdc_interrupt (int irq, void *dev_instance)
spin_lock(&host->lock);
mask &= 0xffff; /* only 16 tags possible */
- if (!mask) {
+ if (mask == 0 && hotplug_status == 0) {
VPRINTK("QUICK EXIT 3\n");
goto done_irq;
}
writel(mask, mmio_base + PDC_INT_SEQMASK);
+ is_sataii_tx4 = pdc_is_sataii_tx4(host->ports[0]->flags);
+
for (i = 0; i < host->n_ports; i++) {
VPRINTK("port %u\n", i);
ap = host->ports[i];
+
+ /* check for a plug or unplug event */
+ ata_no = pdc_port_no_to_ata_no(i, is_sataii_tx4);
+ tmp = hotplug_status & (0x11 << ata_no);
+ if (tmp && ap &&
+ !(ap->flags & ATA_FLAG_DISABLED)) {
+ struct ata_eh_info *ehi = &ap->eh_info;
+ ata_ehi_clear_desc(ehi);
+ ata_ehi_hotplugged(ehi);
+ ata_ehi_push_desc(ehi, "hotplug_status %#x", tmp);
+ ata_port_freeze(ap);
+ ++handled;
+ continue;
+ }
+
+ /* check for a packet interrupt */
tmp = mask & (1 << (i + 1));
if (tmp && ap &&
!(ap->flags & ATA_FLAG_DISABLED)) {
@@ -902,9 +933,9 @@ static void pdc_host_init(struct ata_host *host)
tmp = readl(mmio + hotplug_offset);
writel(tmp | 0xff, mmio + hotplug_offset);
- /* mask plug/unplug ints */
+ /* unmask plug/unplug ints */
tmp = readl(mmio + hotplug_offset);
- writel(tmp | 0xff0000, mmio + hotplug_offset);
+ writel(tmp & ~0xff0000, mmio + hotplug_offset);
/* don't initialise TBG or SLEW on 2nd generation chips */
if (is_gen2)
diff --git a/drivers/ata/sata_sis.c b/drivers/ata/sata_sis.c
index fd80bcf..33716b0 100644
--- a/drivers/ata/sata_sis.c
+++ b/drivers/ata/sata_sis.c
@@ -334,7 +334,7 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
break;
}
- rc = ata_pci_prepare_native_host(pdev, ppi, &host);
+ rc = ata_pci_prepare_sff_host(pdev, ppi, &host);
if (rc)
return rc;
diff --git a/drivers/ata/sata_uli.c b/drivers/ata/sata_uli.c
index aca7181..b52f83a 100644
--- a/drivers/ata/sata_uli.c
+++ b/drivers/ata/sata_uli.c
@@ -213,7 +213,7 @@ static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
host->private_data = hpriv;
/* the first two ports are standard SFF */
- rc = ata_pci_init_native_host(host);
+ rc = ata_pci_init_sff_host(host);
if (rc)
return rc;
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index a4c0832..c412447 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -412,7 +412,7 @@ static int vt6420_prepare_host(struct pci_dev *pdev, struct ata_host **r_host)
struct ata_host *host;
int rc;
- rc = ata_pci_prepare_native_host(pdev, ppi, &host);
+ rc = ata_pci_prepare_sff_host(pdev, ppi, &host);
if (rc)
return rc;
*r_host = host;
diff --git a/include/linux/ata.h b/include/linux/ata.h
index 407dc7e..b5a2016 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -164,6 +164,8 @@ enum {
ATA_CMD_SET_MAX = 0xF9,
ATA_CMD_SET_MAX_EXT = 0x37,
ATA_CMD_READ_LOG_EXT = 0x2f,
+ ATA_CMD_PMP_READ = 0xE4,
+ ATA_CMD_PMP_WRITE = 0xE8,
/* READ_LOG_EXT pages */
ATA_LOG_SATA_NCQ = 0x10,
@@ -212,6 +214,28 @@ enum {
0=to device, 1=to host */
ATAPI_CDB_LEN = 16,
+ /* PMP stuff */
+ SATA_PMP_MAX_PORTS = 15,
+ SATA_PMP_CTRL_PORT = 15,
+
+ SATA_PMP_GSCR_DWORDS = 128,
+ SATA_PMP_GSCR_PROD_ID = 0,
+ SATA_PMP_GSCR_REV = 1,
+ SATA_PMP_GSCR_PORT_INFO = 2,
+ SATA_PMP_GSCR_ERROR = 32,
+ SATA_PMP_GSCR_ERROR_EN = 33,
+ SATA_PMP_GSCR_FEAT = 64,
+ SATA_PMP_GSCR_FEAT_EN = 96,
+
+ SATA_PMP_PSCR_STATUS = 0,
+ SATA_PMP_PSCR_ERROR = 1,
+ SATA_PMP_PSCR_CONTROL = 2,
+
+ SATA_PMP_FEAT_BIST = (1 << 0),
+ SATA_PMP_FEAT_PMREQ = (1 << 1),
+ SATA_PMP_FEAT_DYNSSC = (1 << 2),
+ SATA_PMP_FEAT_NOTIFY = (1 << 3),
+
/* cable types */
ATA_CBL_NONE = 0,
ATA_CBL_PATA40 = 1,
@@ -418,4 +442,9 @@ static inline int lba_48_ok(u64 block, u32 n_block)
return ((block + n_block - 1) < ((u64)1 << 48)) && (n_block <= 65536);
}
+#define sata_pmp_gscr_vendor(gscr) ((gscr)[SATA_PMP_GSCR_PROD_ID] & 0xffff)
+#define sata_pmp_gscr_devid(gscr) ((gscr)[SATA_PMP_GSCR_PROD_ID] >> 16)
+#define sata_pmp_gscr_rev(gscr) (((gscr)[SATA_PMP_GSCR_REV] >> 8) & 0xff)
+#define sata_pmp_gscr_ports(gscr) ((gscr)[SATA_PMP_GSCR_PORT_INFO] & 0xf)
+
#endif /* __LINUX_ATA_H__ */
diff --git a/include/linux/libata.h b/include/linux/libata.h
index a3df646..47cd2a1 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -196,7 +196,6 @@ enum {
ATA_PFLAG_SCSI_HOTPLUG = (1 << 6), /* SCSI hotplug scheduled */
ATA_PFLAG_INITIALIZING = (1 << 7), /* being initialized, don't touch */
- ATA_PFLAG_FLUSH_PORT_TASK = (1 << 16), /* flush port task */
ATA_PFLAG_SUSPENDED = (1 << 17), /* port is suspended (power) */
ATA_PFLAG_PM_PENDING = (1 << 18), /* PM operation pending */
ATA_PFLAG_GTM_VALID = (1 << 19), /* acpi_gtm data valid */
@@ -435,6 +434,7 @@ struct ata_device {
struct ata_port *ap;
unsigned int devno; /* 0 or 1 */
unsigned long flags; /* ATA_DFLAG_xxx */
+ unsigned int horkage; /* List of broken features */
struct scsi_device *sdev; /* attached SCSI device */
#ifdef CONFIG_ATA_ACPI
acpi_handle acpi_handle;
@@ -466,7 +466,6 @@ struct ata_device {
/* error history */
struct ata_ering ering;
int spdn_cnt;
- unsigned int horkage; /* List of broken features */
};
/* Offset into struct ata_device. Fields above it are maintained
@@ -794,7 +793,6 @@ extern void ata_id_string(const u16 *id, unsigned char *s,
extern void ata_id_c_string(const u16 *id, unsigned char *s,
unsigned int ofs, unsigned int len);
extern void ata_id_to_dma_mode(struct ata_device *dev, u8 unknown);
-extern unsigned long ata_device_blacklisted(const struct ata_device *dev);
extern void ata_bmdma_setup (struct ata_queued_cmd *qc);
extern void ata_bmdma_start (struct ata_queued_cmd *qc);
extern void ata_bmdma_stop(struct ata_queued_cmd *qc);
@@ -871,11 +869,11 @@ struct pci_bits {
unsigned long val;
};
-extern int ata_pci_init_native_host(struct ata_host *host);
+extern int ata_pci_init_sff_host(struct ata_host *host);
extern int ata_pci_init_bmdma(struct ata_host *host);
-extern int ata_pci_prepare_native_host(struct pci_dev *pdev,
- const struct ata_port_info * const * ppi,
- struct ata_host **r_host);
+extern int ata_pci_prepare_sff_host(struct pci_dev *pdev,
+ const struct ata_port_info * const * ppi,
+ struct ata_host **r_host);
extern int pci_test_config_bits(struct pci_dev *pdev, const struct pci_bits *bits);
extern unsigned long ata_pci_default_filter(struct ata_device *, unsigned long);
#endif /* CONFIG_PCI */
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2007-07-10 18:36 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2007-07-10 18:36 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Very little of note. Tejun's ACPI updates are useful. And a big Tejun
"port multiplier" (== SATA version of ethernet or USB hub) patchbomb is
waiting to be reviewed.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/ahci.c | 159 +++++--
drivers/ata/ata_generic.c | 4 +-
drivers/ata/ata_piix.c | 35 +-
drivers/ata/libata-acpi.c | 914 +++++++++++++++++----------------------
drivers/ata/libata-core.c | 105 ++++-
drivers/ata/libata-eh.c | 11 +-
drivers/ata/libata-scsi.c | 2 +-
drivers/ata/libata.h | 18 +-
drivers/ata/pata_ali.c | 22 +-
drivers/ata/pata_amd.c | 38 +-
drivers/ata/pata_artop.c | 6 +-
drivers/ata/pata_atiixp.c | 3 +-
drivers/ata/pata_cmd640.c | 2 +-
drivers/ata/pata_cmd64x.c | 12 +-
drivers/ata/pata_cs5520.c | 4 +-
drivers/ata/pata_cs5530.c | 8 +-
drivers/ata/pata_cs5535.c | 4 +-
drivers/ata/pata_cypress.c | 2 +-
drivers/ata/pata_efar.c | 2 +-
drivers/ata/pata_hpt366.c | 4 +-
drivers/ata/pata_hpt37x.c | 20 +-
drivers/ata/pata_hpt3x2n.c | 4 +-
drivers/ata/pata_hpt3x3.c | 2 +-
drivers/ata/pata_icside.c | 2 +-
drivers/ata/pata_it8213.c | 4 +-
drivers/ata/pata_it821x.c | 6 +-
drivers/ata/pata_ixp4xx_cf.c | 76 ++--
drivers/ata/pata_jmicron.c | 4 +-
drivers/ata/pata_marvell.c | 8 +-
drivers/ata/pata_netcell.c | 4 +-
drivers/ata/pata_ns87410.c | 2 +-
drivers/ata/pata_oldpiix.c | 2 +-
drivers/ata/pata_opti.c | 2 +-
drivers/ata/pata_optidma.c | 4 +-
drivers/ata/pata_pdc202xx_old.c | 6 +-
drivers/ata/pata_platform.c | 6 +-
drivers/ata/pata_radisys.c | 2 +-
drivers/ata/pata_rz1000.c | 2 +-
drivers/ata/pata_sc1200.c | 6 +-
drivers/ata/pata_serverworks.c | 12 +-
drivers/ata/pata_sil680.c | 21 +-
drivers/ata/pata_sis.c | 14 +-
drivers/ata/pata_sl82c105.c | 4 +-
drivers/ata/pata_triflex.c | 2 +-
drivers/ata/pata_via.c | 8 +-
drivers/ata/pdc_adma.c | 20 +-
drivers/ata/sata_inic162x.c | 6 +-
drivers/ata/sata_mv.c | 31 +-
drivers/ata/sata_promise.c | 78 ++--
drivers/ata/sata_qstor.c | 2 +-
drivers/ata/sata_sil.c | 13 +-
drivers/ata/sata_sil24.c | 8 +-
drivers/ata/sata_sis.c | 2 +-
drivers/ata/sata_svw.c | 15 +-
drivers/ata/sata_sx4.c | 168 +++++---
drivers/ata/sata_uli.c | 2 +-
drivers/ata/sata_via.c | 10 +-
drivers/ata/sata_vsc.c | 2 +-
include/linux/ata.h | 1 +
include/linux/libata.h | 30 ++-
include/linux/pata_platform.h | 5 +
61 files changed, 1052 insertions(+), 919 deletions(-)
Alan Cox (1):
libata: Support chips with 64K PRD quirk
Alessandro Zummo (1):
[libata] pata_ixp4xx: convert to new EH
Christian Lamparter (1):
Add a PCI ID for santa rosa's PATA controller.
Jeff Garzik (17):
[libata] pata_atiixp: add SB700 PCI ID
[libata] sata_sil: register table cleanup
[libata] PATA drivers: remove ATA_FLAG_SRST
[libata] drivers: remove 'void __iomem *' casts from pre-iomap days
[libata] pdc_adma: Reorder initializers with a couple structs
[libata] sata_sx4: named constant cleanup
[libata] pata_sil680: minor cleanups from benh
[libata] ahci: Factor out SATA port init into a separate function
[libata] ahci: minor internal cleanups
[libata] sata_sx4, sata_via: minor documentation updates
[ATA] Add named constant for ATAPI command DEVICE RESET
[libata] ahci: minor internal cleanups
[libata] pata_ixp4xx: kill unused var
[libata] Clean up driver udma_mask initializers
[libata] AHCI: Add support for Marvell AHCI-like chips (initially 6145)
[libata] Use ATA_UDMAx standard masks when filling driver's udma_mask info
[libata] sata_mv: print out additional chip info during probe
Jens Axboe (1):
use_clustering (sht) bit set to 0 in AHCI ?
Mikael Pettersson (2):
sata_promise: cleanups
sata_sil24: sil24_interrupt() micro-optimisation
Sonic Zhang (1):
Add irq_flags to struct pata_platform_info
Tejun Heo (8):
libata-acpi: implement ata_acpi_associate()
libata-acpi: clean up ata_acpi_exec_tfs()
libata-acpi: miscellaneous cleanups
libata: reimplement ACPI invocation
libata-acpi: remove redundant checks
libata-acpi: implement _GTM/_STM support
libata: replace ap->cbl tests with ATA_FLAG_SATA tests
ata_piix: fix pio/mwdma programming
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index ca5229d..11e4eb9 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -46,7 +46,7 @@
#include <linux/libata.h>
#define DRV_NAME "ahci"
-#define DRV_VERSION "2.2"
+#define DRV_VERSION "2.3"
enum {
@@ -54,7 +54,7 @@ enum {
AHCI_MAX_PORTS = 32,
AHCI_MAX_SG = 168, /* hardware max is 64K */
AHCI_DMA_BOUNDARY = 0xffffffff,
- AHCI_USE_CLUSTERING = 0,
+ AHCI_USE_CLUSTERING = 1,
AHCI_MAX_CMDS = 32,
AHCI_CMD_SZ = 32,
AHCI_CMD_SLOT_SZ = AHCI_MAX_CMDS * AHCI_CMD_SZ,
@@ -81,6 +81,7 @@ enum {
board_ahci_vt8251 = 2,
board_ahci_ign_iferr = 3,
board_ahci_sb600 = 4,
+ board_ahci_mv = 5,
/* global controller registers */
HOST_CAP = 0x00, /* host capabilities */
@@ -171,6 +172,8 @@ enum {
AHCI_FLAG_HONOR_PI = (1 << 26), /* honor PORTS_IMPL */
AHCI_FLAG_IGN_SERR_INTERNAL = (1 << 27), /* ignore SERR_INTERNAL */
AHCI_FLAG_32BIT_ONLY = (1 << 28), /* force 32bit */
+ AHCI_FLAG_MV_PATA = (1 << 29), /* PATA port */
+ AHCI_FLAG_NO_MSI = (1 << 30), /* no PCI MSI */
AHCI_FLAG_COMMON = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA |
@@ -228,9 +231,12 @@ static void ahci_thaw(struct ata_port *ap);
static void ahci_error_handler(struct ata_port *ap);
static void ahci_vt8251_error_handler(struct ata_port *ap);
static void ahci_post_internal_cmd(struct ata_queued_cmd *qc);
+static int ahci_port_resume(struct ata_port *ap);
+static unsigned int ahci_fill_sg(struct ata_queued_cmd *qc, void *cmd_tbl);
+static void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag,
+ u32 opts);
#ifdef CONFIG_PM
static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg);
-static int ahci_port_resume(struct ata_port *ap);
static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
static int ahci_pci_device_resume(struct pci_dev *pdev);
#endif
@@ -327,14 +333,14 @@ static const struct ata_port_info ahci_port_info[] = {
{
.flags = AHCI_FLAG_COMMON,
.pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
/* board_ahci_pi */
{
.flags = AHCI_FLAG_COMMON | AHCI_FLAG_HONOR_PI,
.pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
/* board_ahci_vt8251 */
@@ -342,14 +348,14 @@ static const struct ata_port_info ahci_port_info[] = {
.flags = AHCI_FLAG_COMMON | ATA_FLAG_HRST_TO_RESUME |
AHCI_FLAG_NO_NCQ,
.pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .udma_mask = ATA_UDMA6,
.port_ops = &ahci_vt8251_ops,
},
/* board_ahci_ign_iferr */
{
.flags = AHCI_FLAG_COMMON | AHCI_FLAG_IGN_IRQ_IF_ERR,
.pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
/* board_ahci_sb600 */
@@ -358,7 +364,19 @@ static const struct ata_port_info ahci_port_info[] = {
AHCI_FLAG_IGN_SERR_INTERNAL |
AHCI_FLAG_32BIT_ONLY,
.pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &ahci_ops,
+ },
+ /* board_ahci_mv */
+ {
+ .sht = &ahci_sht,
+ .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+ ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA |
+ ATA_FLAG_SKIP_D2H_BSY | AHCI_FLAG_HONOR_PI |
+ AHCI_FLAG_NO_NCQ | AHCI_FLAG_NO_MSI |
+ AHCI_FLAG_MV_PATA,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
};
@@ -456,6 +474,9 @@ static const struct pci_device_id ahci_pci_tbl[] = {
{ PCI_VDEVICE(SI, 0x1185), board_ahci }, /* SiS 966 */
{ PCI_VDEVICE(SI, 0x0186), board_ahci }, /* SiS 968 */
+ /* Marvell */
+ { PCI_VDEVICE(MARVELL, 0x6145), board_ahci_mv }, /* 6145 */
+
/* Generic, PCI class code for AHCI */
{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_STORAGE_SATA_AHCI, 0xffffff, board_ahci },
@@ -481,11 +502,17 @@ static inline int ahci_nr_ports(u32 cap)
return (cap & 0x1f) + 1;
}
-static inline void __iomem *ahci_port_base(struct ata_port *ap)
+static inline void __iomem *__ahci_port_base(struct ata_host *host,
+ unsigned int port_no)
{
- void __iomem *mmio = ap->host->iomap[AHCI_PCI_BAR];
+ void __iomem *mmio = host->iomap[AHCI_PCI_BAR];
+
+ return mmio + 0x100 + (port_no * 0x80);
+}
- return mmio + 0x100 + (ap->port_no * 0x80);
+static inline void __iomem *ahci_port_base(struct ata_port *ap)
+{
+ return __ahci_port_base(ap->host, ap->port_no);
}
/**
@@ -535,6 +562,20 @@ static void ahci_save_initial_config(struct pci_dev *pdev,
hpriv->saved_port_map = port_map;
}
+ /*
+ * Temporary Marvell 6145 hack: PATA port presence
+ * is asserted through the standard AHCI port
+ * presence register, as bit 4 (counting from 0)
+ */
+ if (pi->flags & AHCI_FLAG_MV_PATA) {
+ dev_printk(KERN_ERR, &pdev->dev,
+ "MV_AHCI HACK: port_map %x -> %x\n",
+ hpriv->port_map,
+ hpriv->port_map & 0xf);
+
+ port_map &= 0xf;
+ }
+
/* cross check port_map and cap.n_ports */
if (pi->flags & AHCI_FLAG_HONOR_PI) {
u32 tmp_port_map = port_map;
@@ -740,7 +781,7 @@ static void ahci_power_down(struct ata_port *ap)
}
#endif
-static void ahci_init_port(struct ata_port *ap)
+static void ahci_start_port(struct ata_port *ap)
{
/* enable FIS reception */
ahci_start_fis_rx(ap);
@@ -814,39 +855,62 @@ static int ahci_reset_controller(struct ata_host *host)
return 0;
}
+static void ahci_port_init(struct pci_dev *pdev, struct ata_port *ap,
+ int port_no, void __iomem *mmio,
+ void __iomem *port_mmio)
+{
+ const char *emsg = NULL;
+ int rc;
+ u32 tmp;
+
+ /* make sure port is not active */
+ rc = ahci_deinit_port(ap, &emsg);
+ if (rc)
+ dev_printk(KERN_WARNING, &pdev->dev,
+ "%s (%d)\n", emsg, rc);
+
+ /* clear SError */
+ tmp = readl(port_mmio + PORT_SCR_ERR);
+ VPRINTK("PORT_SCR_ERR 0x%x\n", tmp);
+ writel(tmp, port_mmio + PORT_SCR_ERR);
+
+ /* clear port IRQ */
+ tmp = readl(port_mmio + PORT_IRQ_STAT);
+ VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
+ if (tmp)
+ writel(tmp, port_mmio + PORT_IRQ_STAT);
+
+ writel(1 << port_no, mmio + HOST_IRQ_STAT);
+}
+
static void ahci_init_controller(struct ata_host *host)
{
struct pci_dev *pdev = to_pci_dev(host->dev);
void __iomem *mmio = host->iomap[AHCI_PCI_BAR];
- int i, rc;
+ int i;
+ void __iomem *port_mmio;
u32 tmp;
- for (i = 0; i < host->n_ports; i++) {
- struct ata_port *ap = host->ports[i];
- void __iomem *port_mmio = ahci_port_base(ap);
- const char *emsg = NULL;
-
- if (ata_port_is_dummy(ap))
- continue;
-
- /* make sure port is not active */
- rc = ahci_deinit_port(ap, &emsg);
- if (rc)
- dev_printk(KERN_WARNING, &pdev->dev,
- "%s (%d)\n", emsg, rc);
+ if (host->ports[0]->flags & AHCI_FLAG_MV_PATA) {
+ port_mmio = __ahci_port_base(host, 4);
- /* clear SError */
- tmp = readl(port_mmio + PORT_SCR_ERR);
- VPRINTK("PORT_SCR_ERR 0x%x\n", tmp);
- writel(tmp, port_mmio + PORT_SCR_ERR);
+ writel(0, port_mmio + PORT_IRQ_MASK);
/* clear port IRQ */
tmp = readl(port_mmio + PORT_IRQ_STAT);
VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
if (tmp)
writel(tmp, port_mmio + PORT_IRQ_STAT);
+ }
- writel(1 << i, mmio + HOST_IRQ_STAT);
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap = host->ports[i];
+
+ port_mmio = ahci_port_base(ap);
+ if (ata_port_is_dummy(ap))
+ continue;
+
+ ahci_port_init(pdev, ap, i, mmio, port_mmio);
}
tmp = readl(mmio + HOST_CTL);
@@ -1232,7 +1296,7 @@ static void ahci_error_intr(struct ata_port *ap, u32 irq_stat)
ata_port_abort(ap);
}
-static void ahci_host_intr(struct ata_port *ap)
+static void ahci_port_intr(struct ata_port *ap)
{
void __iomem *port_mmio = ap->ioaddr.cmd_addr;
struct ata_eh_info *ehi = &ap->eh_info;
@@ -1358,7 +1422,7 @@ static irqreturn_t ahci_interrupt(int irq, void *dev_instance)
ap = host->ports[i];
if (ap) {
- ahci_host_intr(ap);
+ ahci_port_intr(ap);
VPRINTK("port %u\n", i);
} else {
VPRINTK("port %u (no irq)\n", i);
@@ -1466,7 +1530,7 @@ static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg)
ahci_power_down(ap);
else {
ata_port_printk(ap, KERN_ERR, "%s (%d)\n", emsg, rc);
- ahci_init_port(ap);
+ ahci_start_port(ap);
}
return rc;
@@ -1475,7 +1539,7 @@ static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg)
static int ahci_port_resume(struct ata_port *ap)
{
ahci_power_up(ap);
- ahci_init_port(ap);
+ ahci_start_port(ap);
return 0;
}
@@ -1573,13 +1637,8 @@ static int ahci_port_start(struct ata_port *ap)
ap->private_data = pp;
- /* power up port */
- ahci_power_up(ap);
-
- /* initialize port */
- ahci_init_port(ap);
-
- return 0;
+ /* engage engines, captain */
+ return ahci_port_resume(ap);
}
static void ahci_port_stop(struct ata_port *ap)
@@ -1724,7 +1783,7 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (rc)
return rc;
- if (pci_enable_msi(pdev))
+ if ((pi.flags & AHCI_FLAG_NO_MSI) || pci_enable_msi(pdev))
pci_intx(pdev, 1);
hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
@@ -1745,14 +1804,18 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
host->private_data = hpriv;
for (i = 0; i < host->n_ports; i++) {
- if (hpriv->port_map & (1 << i)) {
- struct ata_port *ap = host->ports[i];
- void __iomem *port_mmio = ahci_port_base(ap);
+ struct ata_port *ap = host->ports[i];
+ void __iomem *port_mmio = ahci_port_base(ap);
+ /* standard SATA port setup */
+ if (hpriv->port_map & (1 << i)) {
ap->ioaddr.cmd_addr = port_mmio;
ap->ioaddr.scr_addr = port_mmio + PORT_SCR;
- } else
- host->ports[i]->ops = &ata_dummy_port_ops;
+ }
+
+ /* disabled/not-implemented port */
+ else
+ ap->ops = &ata_dummy_port_ops;
}
/* initialize adapter */
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
index 4c6e95c..430fcf4 100644
--- a/drivers/ata/ata_generic.c
+++ b/drivers/ata/ata_generic.c
@@ -143,10 +143,10 @@ static int ata_generic_init_one(struct pci_dev *dev, const struct pci_device_id
u16 command;
static const struct ata_port_info info = {
.sht = &generic_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ .udma_mask = ATA_UDMA5,
.port_ops = &generic_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 9c07b88..6a3bfef 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -200,6 +200,8 @@ static const struct pci_device_id piix_pci_tbl[] = {
/* ICH7/7-R (i945, i975) UDMA 100*/
{ 0x8086, 0x27DF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_133 },
{ 0x8086, 0x269E, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+ /* ICH8 Mobile PATA Controller */
+ { 0x8086, 0x2850, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
/* NOTE: The following PCI ids must be kept in sync with the
* list in drivers/pci/quirks.c.
@@ -495,7 +497,7 @@ static struct ata_port_info piix_port_info[] = {
.flags = PIIX_SATA_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
@@ -505,7 +507,7 @@ static struct ata_port_info piix_port_info[] = {
.flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
@@ -516,7 +518,7 @@ static struct ata_port_info piix_port_info[] = {
PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
@@ -527,7 +529,7 @@ static struct ata_port_info piix_port_info[] = {
PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
@@ -538,7 +540,7 @@ static struct ata_port_info piix_port_info[] = {
PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
@@ -685,8 +687,14 @@ static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev)
if (adev->class == ATA_DEV_ATA)
control |= 4; /* PPE enable */
+ /* PIO configuration clears DTE unconditionally. It will be
+ * programmed in set_dmamode which is guaranteed to be called
+ * after set_piomode if any DMA mode is available.
+ */
pci_read_config_word(dev, master_port, &master_data);
if (is_slave) {
+ /* clear TIME1|IE1|PPE1|DTE1 */
+ master_data &= 0xff0f;
/* Enable SITRE (seperate slave timing register) */
master_data |= 0x4000;
/* enable PPE1, IE1 and TIME1 as needed */
@@ -694,12 +702,14 @@ static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev)
pci_read_config_byte(dev, slave_port, &slave_data);
slave_data &= (ap->port_no ? 0x0f : 0xf0);
/* Load the timing nibble for this slave */
- slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1])
+ << (ap->port_no ? 4 : 0);
} else {
- /* Master keeps the bits in a different format */
- master_data &= 0xccf8;
+ /* clear ISP|RCT|TIME0|IE0|PPE0|DTE0 */
+ master_data &= 0xccf0;
/* Enable PPE, IE and TIME as appropriate */
master_data |= control;
+ /* load ISP and RCT */
master_data |=
(timings[pio][0] << 12) |
(timings[pio][1] << 8);
@@ -816,7 +826,7 @@ static void do_pata_set_dmamode (struct ata_port *ap, struct ata_device *adev, i
master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */
master_data |= control << 4;
pci_read_config_byte(dev, 0x44, &slave_data);
- slave_data &= (0x0F + 0xE1 * ap->port_no);
+ slave_data &= (ap->port_no ? 0x0f : 0xf0);
/* Load the matching timing */
slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
pci_write_config_byte(dev, 0x44, slave_data);
@@ -828,8 +838,11 @@ static void do_pata_set_dmamode (struct ata_port *ap, struct ata_device *adev, i
(timings[pio][0] << 12) |
(timings[pio][1] << 8);
}
- udma_enable &= ~(1 << devid);
- pci_write_config_word(dev, master_port, master_data);
+
+ if (ap->udma_mask) {
+ udma_enable &= ~(1 << devid);
+ pci_write_config_word(dev, master_port, master_data);
+ }
}
/* Don't scribble on 0x48 if the controller does not support UDMA */
if (ap->udma_mask)
diff --git a/drivers/ata/libata-acpi.c b/drivers/ata/libata-acpi.c
index 0223673..c059f78 100644
--- a/drivers/ata/libata-acpi.c
+++ b/drivers/ata/libata-acpi.c
@@ -24,15 +24,13 @@
#include <acpi/acmacros.h>
#include <acpi/actypes.h>
-#define SATA_ROOT_PORT(x) (((x) >> 16) & 0xffff)
-#define SATA_PORT_NUMBER(x) ((x) & 0xffff) /* or NO_PORT_MULT */
#define NO_PORT_MULT 0xffff
-#define SATA_ADR_RSVD 0xffffffff
+#define SATA_ADR(root,pmp) (((root) << 16) | (pmp))
#define REGS_PER_GTF 7
-struct taskfile_array {
- u8 tfa[REGS_PER_GTF]; /* regs. 0x1f1 - 0x1f7 */
-};
+struct ata_acpi_gtf {
+ u8 tf[REGS_PER_GTF]; /* regs. 0x1f1 - 0x1f7 */
+} __packed;
/*
* Helper - belongs in the PCI layer somewhere eventually
@@ -42,237 +40,173 @@ static int is_pci_dev(struct device *dev)
return (dev->bus == &pci_bus_type);
}
+static void ata_acpi_associate_sata_port(struct ata_port *ap)
+{
+ acpi_integer adr = SATA_ADR(ap->port_no, NO_PORT_MULT);
+
+ ap->device->acpi_handle = acpi_get_child(ap->host->acpi_handle, adr);
+}
+
+static void ata_acpi_associate_ide_port(struct ata_port *ap)
+{
+ int max_devices, i;
+
+ ap->acpi_handle = acpi_get_child(ap->host->acpi_handle, ap->port_no);
+ if (!ap->acpi_handle)
+ return;
+
+ max_devices = 1;
+ if (ap->flags & ATA_FLAG_SLAVE_POSS)
+ max_devices++;
+
+ for (i = 0; i < max_devices; i++) {
+ struct ata_device *dev = &ap->device[i];
+
+ dev->acpi_handle = acpi_get_child(ap->acpi_handle, i);
+ }
+}
+
/**
- * sata_get_dev_handle - finds acpi_handle and PCI device.function
- * @dev: device to locate
- * @handle: returned acpi_handle for @dev
- * @pcidevfn: return PCI device.func for @dev
+ * ata_acpi_associate - associate ATA host with ACPI objects
+ * @host: target ATA host
+ *
+ * Look up ACPI objects associated with @host and initialize
+ * acpi_handle fields of @host, its ports and devices accordingly.
*
- * This function is somewhat SATA-specific. Or at least the
- * PATA & SATA versions of this function are different,
- * so it's not entirely generic code.
+ * LOCKING:
+ * EH context.
*
- * Returns 0 on success, <0 on error.
+ * RETURNS:
+ * 0 on success, -errno on failure.
*/
-static int sata_get_dev_handle(struct device *dev, acpi_handle *handle,
- acpi_integer *pcidevfn)
+void ata_acpi_associate(struct ata_host *host)
{
- struct pci_dev *pci_dev;
- acpi_integer addr;
-
- if (!is_pci_dev(dev))
- return -ENODEV;
-
- pci_dev = to_pci_dev(dev); /* NOTE: PCI-specific */
- /* Please refer to the ACPI spec for the syntax of _ADR. */
- addr = (PCI_SLOT(pci_dev->devfn) << 16) | PCI_FUNC(pci_dev->devfn);
- *pcidevfn = addr;
- *handle = acpi_get_child(DEVICE_ACPI_HANDLE(dev->parent), addr);
- if (!*handle)
- return -ENODEV;
- return 0;
+ int i;
+
+ if (!is_pci_dev(host->dev) || libata_noacpi)
+ return;
+
+ host->acpi_handle = DEVICE_ACPI_HANDLE(host->dev);
+ if (!host->acpi_handle)
+ return;
+
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap = host->ports[i];
+
+ if (host->ports[0]->flags & ATA_FLAG_ACPI_SATA)
+ ata_acpi_associate_sata_port(ap);
+ else
+ ata_acpi_associate_ide_port(ap);
+ }
}
/**
- * pata_get_dev_handle - finds acpi_handle and PCI device.function
- * @dev: device to locate
- * @handle: returned acpi_handle for @dev
- * @pcidevfn: return PCI device.func for @dev
+ * ata_acpi_gtm - execute _GTM
+ * @ap: target ATA port
+ * @gtm: out parameter for _GTM result
+ *
+ * Evaluate _GTM and store the result in @gtm.
*
- * The PATA and SATA versions of this function are different.
+ * LOCKING:
+ * EH context.
*
- * Returns 0 on success, <0 on error.
+ * RETURNS:
+ * 0 on success, -ENOENT if _GTM doesn't exist, -errno on failure.
*/
-static int pata_get_dev_handle(struct device *dev, acpi_handle *handle,
- acpi_integer *pcidevfn)
+static int ata_acpi_gtm(const struct ata_port *ap, struct ata_acpi_gtm *gtm)
{
- unsigned int bus, devnum, func;
- acpi_integer addr;
- acpi_handle dev_handle, parent_handle;
- struct acpi_buffer buffer = {.length = ACPI_ALLOCATE_BUFFER,
- .pointer = NULL};
+ struct acpi_buffer output = { .length = ACPI_ALLOCATE_BUFFER };
+ union acpi_object *out_obj;
acpi_status status;
- struct acpi_device_info *dinfo = NULL;
- int ret = -ENODEV;
- struct pci_dev *pdev;
-
- if (!is_pci_dev(dev))
- return -ENODEV;
-
- pdev = to_pci_dev(dev);
-
- bus = pdev->bus->number;
- devnum = PCI_SLOT(pdev->devfn);
- func = PCI_FUNC(pdev->devfn);
-
- dev_handle = DEVICE_ACPI_HANDLE(dev);
- parent_handle = DEVICE_ACPI_HANDLE(dev->parent);
-
- status = acpi_get_object_info(parent_handle, &buffer);
- if (ACPI_FAILURE(status))
- goto err;
-
- dinfo = buffer.pointer;
- if (dinfo && (dinfo->valid & ACPI_VALID_ADR) &&
- dinfo->address == bus) {
- /* ACPI spec for _ADR for PCI bus: */
- addr = (acpi_integer)(devnum << 16 | func);
- *pcidevfn = addr;
- *handle = dev_handle;
- } else {
- goto err;
+ int rc = 0;
+
+ status = acpi_evaluate_object(ap->acpi_handle, "_GTM", NULL, &output);
+
+ rc = -ENOENT;
+ if (status == AE_NOT_FOUND)
+ goto out_free;
+
+ rc = -EINVAL;
+ if (ACPI_FAILURE(status)) {
+ ata_port_printk(ap, KERN_ERR,
+ "ACPI get timing mode failed (AE 0x%x)\n",
+ status);
+ goto out_free;
}
- if (!*handle)
- goto err;
- ret = 0;
-err:
- kfree(dinfo);
- return ret;
-}
+ out_obj = output.pointer;
+ if (out_obj->type != ACPI_TYPE_BUFFER) {
+ ata_port_printk(ap, KERN_WARNING,
+ "_GTM returned unexpected object type 0x%x\n",
+ out_obj->type);
-struct walk_info { /* can be trimmed some */
- struct device *dev;
- struct acpi_device *adev;
- acpi_handle handle;
- acpi_integer pcidevfn;
- unsigned int drivenum;
- acpi_handle obj_handle;
- struct ata_port *ataport;
- struct ata_device *atadev;
- u32 sata_adr;
- int status;
- char basepath[ACPI_PATHNAME_MAX];
- int basepath_len;
-};
-
-static acpi_status get_devices(acpi_handle handle,
- u32 level, void *context, void **return_value)
-{
- acpi_status status;
- struct walk_info *winfo = context;
- struct acpi_buffer namebuf = {ACPI_ALLOCATE_BUFFER, NULL};
- char *pathname;
- struct acpi_buffer buffer;
- struct acpi_device_info *dinfo;
-
- status = acpi_get_name(handle, ACPI_FULL_PATHNAME, &namebuf);
- if (status)
- goto ret;
- pathname = namebuf.pointer;
-
- buffer.length = ACPI_ALLOCATE_BUFFER;
- buffer.pointer = NULL;
- status = acpi_get_object_info(handle, &buffer);
- if (ACPI_FAILURE(status))
- goto out2;
-
- dinfo = buffer.pointer;
-
- /* find full device path name for pcidevfn */
- if (dinfo && (dinfo->valid & ACPI_VALID_ADR) &&
- dinfo->address == winfo->pcidevfn) {
- if (ata_msg_probe(winfo->ataport))
- ata_dev_printk(winfo->atadev, KERN_DEBUG,
- ":%s: matches pcidevfn (0x%llx)\n",
- pathname, winfo->pcidevfn);
- strlcpy(winfo->basepath, pathname,
- sizeof(winfo->basepath));
- winfo->basepath_len = strlen(pathname);
- goto out;
+ goto out_free;
}
- /* if basepath is not yet known, ignore this object */
- if (!winfo->basepath_len)
- goto out;
-
- /* if this object is in scope of basepath, maybe use it */
- if (strncmp(pathname, winfo->basepath,
- winfo->basepath_len) == 0) {
- if (!(dinfo->valid & ACPI_VALID_ADR))
- goto out;
- if (ata_msg_probe(winfo->ataport))
- ata_dev_printk(winfo->atadev, KERN_DEBUG,
- "GOT ONE: (%s) root_port = 0x%llx,"
- " port_num = 0x%llx\n", pathname,
- SATA_ROOT_PORT(dinfo->address),
- SATA_PORT_NUMBER(dinfo->address));
- /* heuristics: */
- if (SATA_PORT_NUMBER(dinfo->address) != NO_PORT_MULT)
- if (ata_msg_probe(winfo->ataport))
- ata_dev_printk(winfo->atadev,
- KERN_DEBUG, "warning: don't"
- " know how to handle SATA port"
- " multiplier\n");
- if (SATA_ROOT_PORT(dinfo->address) ==
- winfo->ataport->port_no &&
- SATA_PORT_NUMBER(dinfo->address) == NO_PORT_MULT) {
- if (ata_msg_probe(winfo->ataport))
- ata_dev_printk(winfo->atadev,
- KERN_DEBUG,
- "THIS ^^^^^ is the requested"
- " SATA drive (handle = 0x%p)\n",
- handle);
- winfo->sata_adr = dinfo->address;
- winfo->obj_handle = handle;
- }
+ if (out_obj->buffer.length != sizeof(struct ata_acpi_gtm)) {
+ ata_port_printk(ap, KERN_ERR,
+ "_GTM returned invalid length %d\n",
+ out_obj->buffer.length);
+ goto out_free;
}
-out:
- kfree(dinfo);
-out2:
- kfree(pathname);
-ret:
- return status;
+ memcpy(gtm, out_obj->buffer.pointer, sizeof(struct ata_acpi_gtm));
+ rc = 0;
+ out_free:
+ kfree(output.pointer);
+ return rc;
}
-/* Get the SATA drive _ADR object. */
-static int get_sata_adr(struct device *dev, acpi_handle handle,
- acpi_integer pcidevfn, unsigned int drive,
- struct ata_port *ap,
- struct ata_device *atadev, u32 *dev_adr)
+/**
+ * ata_acpi_stm - execute _STM
+ * @ap: target ATA port
+ * @stm: timing parameter to _STM
+ *
+ * Evaluate _STM with timing parameter @stm.
+ *
+ * LOCKING:
+ * EH context.
+ *
+ * RETURNS:
+ * 0 on success, -ENOENT if _STM doesn't exist, -errno on failure.
+ */
+static int ata_acpi_stm(const struct ata_port *ap, struct ata_acpi_gtm *stm)
{
- acpi_status status;
- struct walk_info *winfo;
- int err = -ENOMEM;
-
- winfo = kzalloc(sizeof(struct walk_info), GFP_KERNEL);
- if (!winfo)
- goto out;
-
- winfo->dev = dev;
- winfo->atadev = atadev;
- winfo->ataport = ap;
- if (acpi_bus_get_device(handle, &winfo->adev) < 0)
- if (ata_msg_probe(ap))
- ata_dev_printk(winfo->atadev, KERN_DEBUG,
- "acpi_bus_get_device failed\n");
- winfo->handle = handle;
- winfo->pcidevfn = pcidevfn;
- winfo->drivenum = drive;
+ acpi_status status;
+ struct acpi_object_list input;
+ union acpi_object in_params[3];
- status = acpi_get_devices(NULL, get_devices, winfo, NULL);
+ in_params[0].type = ACPI_TYPE_BUFFER;
+ in_params[0].buffer.length = sizeof(struct ata_acpi_gtm);
+ in_params[0].buffer.pointer = (u8 *)stm;
+ /* Buffers for id may need byteswapping ? */
+ in_params[1].type = ACPI_TYPE_BUFFER;
+ in_params[1].buffer.length = 512;
+ in_params[1].buffer.pointer = (u8 *)ap->device[0].id;
+ in_params[2].type = ACPI_TYPE_BUFFER;
+ in_params[2].buffer.length = 512;
+ in_params[2].buffer.pointer = (u8 *)ap->device[1].id;
+
+ input.count = 3;
+ input.pointer = in_params;
+
+ status = acpi_evaluate_object(ap->acpi_handle, "_STM", &input, NULL);
+
+ if (status == AE_NOT_FOUND)
+ return -ENOENT;
if (ACPI_FAILURE(status)) {
- if (ata_msg_probe(ap))
- ata_dev_printk(winfo->atadev, KERN_DEBUG,
- "%s: acpi_get_devices failed\n",
- __FUNCTION__);
- err = -ENODEV;
- } else {
- *dev_adr = winfo->sata_adr;
- atadev->obj_handle = winfo->obj_handle;
- err = 0;
+ ata_port_printk(ap, KERN_ERR,
+ "ACPI set timing mode failed (status=0x%x)\n", status);
+ return -EINVAL;
}
- kfree(winfo);
-out:
- return err;
+ return 0;
}
/**
- * do_drive_get_GTF - get the drive bootup default taskfile settings
+ * ata_dev_get_GTF - get the drive bootup default taskfile settings
* @dev: target ATA device
- * @gtf_length: number of bytes of _GTF data returned at @gtf_address
- * @gtf_address: buffer containing _GTF taskfile arrays
+ * @gtf: output parameter for buffer containing _GTF taskfile arrays
+ * @ptr_to_free: pointer which should be freed
*
* This applies to both PATA and SATA drives.
*
@@ -282,121 +216,41 @@ out:
* The <variable number> is not known in advance, so have ACPI-CA
* allocate the buffer as needed and return it, then free it later.
*
- * The returned @gtf_length and @gtf_address are only valid if the
- * function return value is 0.
+ * LOCKING:
+ * EH context.
+ *
+ * RETURNS:
+ * Number of taskfiles on success, 0 if _GTF doesn't exist or doesn't
+ * contain valid data. -errno on other errors.
*/
-static int do_drive_get_GTF(struct ata_device *dev, unsigned int *gtf_length,
- unsigned long *gtf_address, unsigned long *obj_loc)
+static int ata_dev_get_GTF(struct ata_device *dev, struct ata_acpi_gtf **gtf,
+ void **ptr_to_free)
{
struct ata_port *ap = dev->ap;
acpi_status status;
- acpi_handle dev_handle = NULL;
- acpi_handle chan_handle, drive_handle;
- acpi_integer pcidevfn = 0;
- u32 dev_adr;
struct acpi_buffer output;
union acpi_object *out_obj;
- struct device *gdev = ap->host->dev;
- int err = -ENODEV;
+ int rc = 0;
- *gtf_length = 0;
- *gtf_address = 0UL;
- *obj_loc = 0UL;
-
- if (libata_noacpi)
- return 0;
+ /* set up output buffer */
+ output.length = ACPI_ALLOCATE_BUFFER;
+ output.pointer = NULL; /* ACPI-CA sets this; save/free it later */
if (ata_msg_probe(ap))
ata_dev_printk(dev, KERN_DEBUG, "%s: ENTER: port#: %d\n",
__FUNCTION__, ap->port_no);
- if (!ata_dev_enabled(dev) || (ap->flags & ATA_FLAG_DISABLED)) {
- if (ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_DEBUG, "%s: ERR: "
- "ata_dev_present: %d, PORT_DISABLED: %lu\n",
- __FUNCTION__, ata_dev_enabled(dev),
- ap->flags & ATA_FLAG_DISABLED);
- goto out;
- }
-
- /* Don't continue if device has no _ADR method.
- * _GTF is intended for known motherboard devices. */
- if (!(ap->flags & ATA_FLAG_ACPI_SATA)) {
- err = pata_get_dev_handle(gdev, &dev_handle, &pcidevfn);
- if (err < 0) {
- if (ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_DEBUG,
- "%s: pata_get_dev_handle failed (%d)\n",
- __FUNCTION__, err);
- goto out;
- }
- } else {
- err = sata_get_dev_handle(gdev, &dev_handle, &pcidevfn);
- if (err < 0) {
- if (ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_DEBUG,
- "%s: sata_get_dev_handle failed (%d\n",
- __FUNCTION__, err);
- goto out;
- }
- }
-
- /* Get this drive's _ADR info. if not already known. */
- if (!dev->obj_handle) {
- if (!(ap->flags & ATA_FLAG_ACPI_SATA)) {
- /* get child objects of dev_handle == channel objects,
- * + _their_ children == drive objects */
- /* channel is ap->port_no */
- chan_handle = acpi_get_child(dev_handle,
- ap->port_no);
- if (ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_DEBUG,
- "%s: chan adr=%d: chan_handle=0x%p\n",
- __FUNCTION__, ap->port_no,
- chan_handle);
- if (!chan_handle) {
- err = -ENODEV;
- goto out;
- }
- /* TBD: could also check ACPI object VALID bits */
- drive_handle = acpi_get_child(chan_handle, dev->devno);
- if (!drive_handle) {
- err = -ENODEV;
- goto out;
- }
- dev_adr = dev->devno;
- dev->obj_handle = drive_handle;
- } else { /* for SATA mode */
- dev_adr = SATA_ADR_RSVD;
- err = get_sata_adr(gdev, dev_handle, pcidevfn, 0,
- ap, dev, &dev_adr);
- }
- if (err < 0 || dev_adr == SATA_ADR_RSVD ||
- !dev->obj_handle) {
- if (ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_DEBUG,
- "%s: get_sata/pata_adr failed: "
- "err=%d, dev_adr=%u, obj_handle=0x%p\n",
- __FUNCTION__, err, dev_adr,
- dev->obj_handle);
- goto out;
- }
- }
-
- /* Setting up output buffer */
- output.length = ACPI_ALLOCATE_BUFFER;
- output.pointer = NULL; /* ACPI-CA sets this; save/free it later */
-
/* _GTF has no input parameters */
- err = -EIO;
- status = acpi_evaluate_object(dev->obj_handle, "_GTF",
- NULL, &output);
+ status = acpi_evaluate_object(dev->acpi_handle, "_GTF", NULL, &output);
+
if (ACPI_FAILURE(status)) {
- if (ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_DEBUG,
- "%s: Run _GTF error: status = 0x%x\n",
- __FUNCTION__, status);
- goto out;
+ if (status != AE_NOT_FOUND) {
+ ata_dev_printk(dev, KERN_WARNING,
+ "_GTF evaluation failed (AE 0x%x)\n",
+ status);
+ rc = -EIO;
+ }
+ goto out_free;
}
if (!output.length || !output.pointer) {
@@ -406,43 +260,39 @@ static int do_drive_get_GTF(struct ata_device *dev, unsigned int *gtf_length,
__FUNCTION__,
(unsigned long long)output.length,
output.pointer);
- kfree(output.pointer);
- goto out;
+ goto out_free;
}
out_obj = output.pointer;
if (out_obj->type != ACPI_TYPE_BUFFER) {
- kfree(output.pointer);
- if (ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_DEBUG, "%s: Run _GTF: "
- "error: expected object type of "
- " ACPI_TYPE_BUFFER, got 0x%x\n",
- __FUNCTION__, out_obj->type);
- err = -ENOENT;
- goto out;
+ ata_dev_printk(dev, KERN_WARNING,
+ "_GTF unexpected object type 0x%x\n",
+ out_obj->type);
+ rc = -EINVAL;
+ goto out_free;
}
- if (!out_obj->buffer.length || !out_obj->buffer.pointer ||
- out_obj->buffer.length % REGS_PER_GTF) {
- if (ata_msg_drv(ap))
- ata_dev_printk(dev, KERN_ERR,
- "%s: unexpected GTF length (%d) or addr (0x%p)\n",
- __FUNCTION__, out_obj->buffer.length,
- out_obj->buffer.pointer);
- err = -ENOENT;
- goto out;
+ if (out_obj->buffer.length % REGS_PER_GTF) {
+ ata_dev_printk(dev, KERN_WARNING,
+ "unexpected _GTF length (%d)\n",
+ out_obj->buffer.length);
+ rc = -EINVAL;
+ goto out_free;
}
- *gtf_length = out_obj->buffer.length;
- *gtf_address = (unsigned long)out_obj->buffer.pointer;
- *obj_loc = (unsigned long)out_obj;
+ *ptr_to_free = out_obj;
+ *gtf = (void *)out_obj->buffer.pointer;
+ rc = out_obj->buffer.length / REGS_PER_GTF;
+
if (ata_msg_probe(ap))
ata_dev_printk(dev, KERN_DEBUG, "%s: returning "
- "gtf_length=%d, gtf_address=0x%lx, obj_loc=0x%lx\n",
- __FUNCTION__, *gtf_length, *gtf_address, *obj_loc);
- err = 0;
-out:
- return err;
+ "gtf=%p, gtf_count=%d, ptr_to_free=%p\n",
+ __FUNCTION__, *gtf, rc, *ptr_to_free);
+ return rc;
+
+ out_free:
+ kfree(output.pointer);
+ return rc;
}
/**
@@ -461,154 +311,99 @@ out:
* function also waits for idle after writing control and before
* writing the remaining registers.
*
- * LOCKING: TBD:
- * Inherited from caller.
+ * LOCKING:
+ * EH context.
+ *
+ * RETURNS:
+ * 0 on success, -errno on failure.
*/
-static void taskfile_load_raw(struct ata_device *dev,
- const struct taskfile_array *gtf)
+static int taskfile_load_raw(struct ata_device *dev,
+ const struct ata_acpi_gtf *gtf)
{
struct ata_port *ap = dev->ap;
- struct ata_taskfile tf;
- unsigned int err;
+ struct ata_taskfile tf, rtf;
+ unsigned int err_mask;
- if (ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_DEBUG, "%s: (0x1f1-1f7): hex: "
- "%02x %02x %02x %02x %02x %02x %02x\n",
- __FUNCTION__,
- gtf->tfa[0], gtf->tfa[1], gtf->tfa[2],
- gtf->tfa[3], gtf->tfa[4], gtf->tfa[5], gtf->tfa[6]);
-
- if ((gtf->tfa[0] == 0) && (gtf->tfa[1] == 0) && (gtf->tfa[2] == 0)
- && (gtf->tfa[3] == 0) && (gtf->tfa[4] == 0) && (gtf->tfa[5] == 0)
- && (gtf->tfa[6] == 0))
- return;
+ if ((gtf->tf[0] == 0) && (gtf->tf[1] == 0) && (gtf->tf[2] == 0)
+ && (gtf->tf[3] == 0) && (gtf->tf[4] == 0) && (gtf->tf[5] == 0)
+ && (gtf->tf[6] == 0))
+ return 0;
ata_tf_init(dev, &tf);
/* convert gtf to tf */
tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; /* TBD */
tf.protocol = ATA_PROT_NODATA;
- tf.feature = gtf->tfa[0]; /* 0x1f1 */
- tf.nsect = gtf->tfa[1]; /* 0x1f2 */
- tf.lbal = gtf->tfa[2]; /* 0x1f3 */
- tf.lbam = gtf->tfa[3]; /* 0x1f4 */
- tf.lbah = gtf->tfa[4]; /* 0x1f5 */
- tf.device = gtf->tfa[5]; /* 0x1f6 */
- tf.command = gtf->tfa[6]; /* 0x1f7 */
-
- err = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0);
- if (err && ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_ERR,
- "%s: ata_exec_internal failed: %u\n",
- __FUNCTION__, err);
-}
-
-/**
- * do_drive_set_taskfiles - write the drive taskfile settings from _GTF
- * @dev: target ATA device
- * @gtf_length: total number of bytes of _GTF taskfiles
- * @gtf_address: location of _GTF taskfile arrays
- *
- * This applies to both PATA and SATA drives.
- *
- * Write {gtf_address, length gtf_length} in groups of
- * REGS_PER_GTF bytes.
- */
-static int do_drive_set_taskfiles(struct ata_device *dev,
- unsigned int gtf_length,
- unsigned long gtf_address)
-{
- struct ata_port *ap = dev->ap;
- int err = -ENODEV;
- int gtf_count = gtf_length / REGS_PER_GTF;
- int ix;
- struct taskfile_array *gtf;
+ tf.feature = gtf->tf[0]; /* 0x1f1 */
+ tf.nsect = gtf->tf[1]; /* 0x1f2 */
+ tf.lbal = gtf->tf[2]; /* 0x1f3 */
+ tf.lbam = gtf->tf[3]; /* 0x1f4 */
+ tf.lbah = gtf->tf[4]; /* 0x1f5 */
+ tf.device = gtf->tf[5]; /* 0x1f6 */
+ tf.command = gtf->tf[6]; /* 0x1f7 */
if (ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_DEBUG, "%s: ENTER: port#: %d\n",
- __FUNCTION__, ap->port_no);
-
- if (libata_noacpi || !(ap->flags & ATA_FLAG_ACPI_SATA))
- return 0;
-
- if (!ata_dev_enabled(dev) || (ap->flags & ATA_FLAG_DISABLED))
- goto out;
- if (!gtf_count) /* shouldn't be here */
- goto out;
-
- if (gtf_length % REGS_PER_GTF) {
- if (ata_msg_drv(ap))
- ata_dev_printk(dev, KERN_ERR,
- "%s: unexpected GTF length (%d)\n",
- __FUNCTION__, gtf_length);
- goto out;
- }
-
- for (ix = 0; ix < gtf_count; ix++) {
- gtf = (struct taskfile_array *)
- (gtf_address + ix * REGS_PER_GTF);
-
- /* send all TaskFile registers (0x1f1-0x1f7) *in*that*order* */
- taskfile_load_raw(dev, gtf);
+ ata_dev_printk(dev, KERN_DEBUG, "executing ACPI cmd "
+ "%02x/%02x:%02x:%02x:%02x:%02x:%02x\n",
+ tf.command, tf.feature, tf.nsect,
+ tf.lbal, tf.lbam, tf.lbah, tf.device);
+
+ rtf = tf;
+ err_mask = ata_exec_internal(dev, &rtf, NULL, DMA_NONE, NULL, 0);
+ if (err_mask) {
+ ata_dev_printk(dev, KERN_ERR,
+ "ACPI cmd %02x/%02x:%02x:%02x:%02x:%02x:%02x failed "
+ "(Emask=0x%x Stat=0x%02x Err=0x%02x)\n",
+ tf.command, tf.feature, tf.nsect, tf.lbal, tf.lbam,
+ tf.lbah, tf.device, err_mask, rtf.command, rtf.feature);
+ return -EIO;
}
- err = 0;
-out:
- return err;
+ return 0;
}
/**
* ata_acpi_exec_tfs - get then write drive taskfile settings
- * @ap: the ata_port for the drive
+ * @dev: target ATA device
*
- * This applies to both PATA and SATA drives.
+ * Evaluate _GTF and excute returned taskfiles.
+ *
+ * LOCKING:
+ * EH context.
+ *
+ * RETURNS:
+ * Number of executed taskfiles on success, 0 if _GTF doesn't exist or
+ * doesn't contain valid data. -errno on other errors.
*/
-int ata_acpi_exec_tfs(struct ata_port *ap)
+static int ata_acpi_exec_tfs(struct ata_device *dev)
{
- int ix;
- int ret = 0;
- unsigned int gtf_length;
- unsigned long gtf_address;
- unsigned long obj_loc;
-
- if (libata_noacpi)
- return 0;
- /*
- * TBD - implement PATA support. For now,
- * we should not run GTF on PATA devices since some
- * PATA require execution of GTM/STM before GTF.
- */
- if (!(ap->flags & ATA_FLAG_ACPI_SATA))
- return 0;
-
- for (ix = 0; ix < ATA_MAX_DEVICES; ix++) {
- struct ata_device *dev = &ap->device[ix];
-
- if (!ata_dev_enabled(dev))
- continue;
-
- ret = do_drive_get_GTF(dev, >f_length, >f_address,
- &obj_loc);
- if (ret < 0) {
- if (ata_msg_probe(ap))
- ata_port_printk(ap, KERN_DEBUG,
- "%s: get_GTF error (%d)\n",
- __FUNCTION__, ret);
- break;
- }
-
- ret = do_drive_set_taskfiles(dev, gtf_length, gtf_address);
- kfree((void *)obj_loc);
- if (ret < 0) {
- if (ata_msg_probe(ap))
- ata_port_printk(ap, KERN_DEBUG,
- "%s: set_taskfiles error (%d)\n",
- __FUNCTION__, ret);
- break;
- }
+ struct ata_acpi_gtf *gtf = NULL;
+ void *ptr_to_free = NULL;
+ int gtf_count, i, rc;
+
+ /* get taskfiles */
+ rc = ata_dev_get_GTF(dev, >f, &ptr_to_free);
+ if (rc < 0)
+ return rc;
+ gtf_count = rc;
+
+ /* execute them */
+ for (i = 0, rc = 0; i < gtf_count; i++) {
+ int tmp;
+
+ /* ACPI errors are eventually ignored. Run till the
+ * end even after errors.
+ */
+ tmp = taskfile_load_raw(dev, gtf++);
+ if (!rc)
+ rc = tmp;
}
- return ret;
+ kfree(ptr_to_free);
+
+ if (rc == 0)
+ return gtf_count;
+ return rc;
}
/**
@@ -620,62 +415,25 @@ int ata_acpi_exec_tfs(struct ata_port *ap)
* ATM this function never returns a failure. It is an optional
* method and if it fails for whatever reason, we should still
* just keep going.
+ *
+ * LOCKING:
+ * EH context.
+ *
+ * RETURNS:
+ * 0 on success, -errno on failure.
*/
-int ata_acpi_push_id(struct ata_device *dev)
+static int ata_acpi_push_id(struct ata_device *dev)
{
struct ata_port *ap = dev->ap;
- acpi_handle handle;
- acpi_integer pcidevfn;
int err;
- struct device *gdev = ap->host->dev;
- u32 dev_adr;
acpi_status status;
struct acpi_object_list input;
union acpi_object in_params[1];
- if (libata_noacpi)
- return 0;
-
if (ata_msg_probe(ap))
ata_dev_printk(dev, KERN_DEBUG, "%s: ix = %d, port#: %d\n",
__FUNCTION__, dev->devno, ap->port_no);
- /* Don't continue if not a SATA device. */
- if (!(ap->flags & ATA_FLAG_ACPI_SATA)) {
- if (ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_DEBUG,
- "%s: Not a SATA device\n", __FUNCTION__);
- goto out;
- }
-
- /* Don't continue if device has no _ADR method.
- * _SDD is intended for known motherboard devices. */
- err = sata_get_dev_handle(gdev, &handle, &pcidevfn);
- if (err < 0) {
- if (ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_DEBUG,
- "%s: sata_get_dev_handle failed (%d\n",
- __FUNCTION__, err);
- goto out;
- }
-
- /* Get this drive's _ADR info, if not already known */
- if (!dev->obj_handle) {
- dev_adr = SATA_ADR_RSVD;
- err = get_sata_adr(gdev, handle, pcidevfn, dev->devno, ap, dev,
- &dev_adr);
- if (err < 0 || dev_adr == SATA_ADR_RSVD ||
- !dev->obj_handle) {
- if (ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_DEBUG,
- "%s: get_sata_adr failed: "
- "err=%d, dev_adr=%u, obj_handle=0x%p\n",
- __FUNCTION__, err, dev_adr,
- dev->obj_handle);
- goto out;
- }
- }
-
/* Give the drive Identify data to the drive via the _SDD method */
/* _SDD: set up input parameters */
input.count = 1;
@@ -687,20 +445,150 @@ int ata_acpi_push_id(struct ata_device *dev)
/* It's OK for _SDD to be missing too. */
swap_buf_le16(dev->id, ATA_ID_WORDS);
- status = acpi_evaluate_object(dev->obj_handle, "_SDD", &input, NULL);
+ status = acpi_evaluate_object(dev->acpi_handle, "_SDD", &input, NULL);
swap_buf_le16(dev->id, ATA_ID_WORDS);
err = ACPI_FAILURE(status) ? -EIO : 0;
- if (err < 0) {
- if (ata_msg_probe(ap))
- ata_dev_printk(dev, KERN_DEBUG,
- "%s _SDD error: status = 0x%x\n",
- __FUNCTION__, status);
+ if (err < 0)
+ ata_dev_printk(dev, KERN_WARNING,
+ "ACPI _SDD failed (AE 0x%x)\n", status);
+
+ return err;
+}
+
+/**
+ * ata_acpi_on_suspend - ATA ACPI hook called on suspend
+ * @ap: target ATA port
+ *
+ * This function is called when @ap is about to be suspended. All
+ * devices are already put to sleep but the port_suspend() callback
+ * hasn't been executed yet. Error return from this function aborts
+ * suspend.
+ *
+ * LOCKING:
+ * EH context.
+ *
+ * RETURNS:
+ * 0 on success, -errno on failure.
+ */
+int ata_acpi_on_suspend(struct ata_port *ap)
+{
+ unsigned long flags;
+ int rc;
+
+ /* proceed iff per-port acpi_handle is valid */
+ if (!ap->acpi_handle)
+ return 0;
+ BUG_ON(ap->flags & ATA_FLAG_ACPI_SATA);
+
+ /* store timing parameters */
+ rc = ata_acpi_gtm(ap, &ap->acpi_gtm);
+
+ spin_lock_irqsave(ap->lock, flags);
+ if (rc == 0)
+ ap->pflags |= ATA_PFLAG_GTM_VALID;
+ else
+ ap->pflags &= ~ATA_PFLAG_GTM_VALID;
+ spin_unlock_irqrestore(ap->lock, flags);
+
+ if (rc == -ENOENT)
+ rc = 0;
+ return rc;
+}
+
+/**
+ * ata_acpi_on_resume - ATA ACPI hook called on resume
+ * @ap: target ATA port
+ *
+ * This function is called when @ap is resumed - right after port
+ * itself is resumed but before any EH action is taken.
+ *
+ * LOCKING:
+ * EH context.
+ */
+void ata_acpi_on_resume(struct ata_port *ap)
+{
+ int i;
+
+ if (ap->acpi_handle && (ap->pflags & ATA_PFLAG_GTM_VALID)) {
+ BUG_ON(ap->flags & ATA_FLAG_ACPI_SATA);
+
+ /* restore timing parameters */
+ ata_acpi_stm(ap, &ap->acpi_gtm);
}
- /* always return success */
-out:
- return 0;
+ /* schedule _GTF */
+ for (i = 0; i < ATA_MAX_DEVICES; i++)
+ ap->device[i].flags |= ATA_DFLAG_ACPI_PENDING;
}
+/**
+ * ata_acpi_on_devcfg - ATA ACPI hook called on device donfiguration
+ * @dev: target ATA device
+ *
+ * This function is called when @dev is about to be configured.
+ * IDENTIFY data might have been modified after this hook is run.
+ *
+ * LOCKING:
+ * EH context.
+ *
+ * RETURNS:
+ * Positive number if IDENTIFY data needs to be refreshed, 0 if not,
+ * -errno on failure.
+ */
+int ata_acpi_on_devcfg(struct ata_device *dev)
+{
+ struct ata_port *ap = dev->ap;
+ struct ata_eh_context *ehc = &ap->eh_context;
+ int acpi_sata = ap->flags & ATA_FLAG_ACPI_SATA;
+ int rc;
+
+ if (!dev->acpi_handle)
+ return 0;
+
+ /* do we need to do _GTF? */
+ if (!(dev->flags & ATA_DFLAG_ACPI_PENDING) &&
+ !(acpi_sata && (ehc->i.flags & ATA_EHI_DID_HARDRESET)))
+ return 0;
+
+ /* do _SDD if SATA */
+ if (acpi_sata) {
+ rc = ata_acpi_push_id(dev);
+ if (rc)
+ goto acpi_err;
+ }
+
+ /* do _GTF */
+ rc = ata_acpi_exec_tfs(dev);
+ if (rc < 0)
+ goto acpi_err;
+
+ dev->flags &= ~ATA_DFLAG_ACPI_PENDING;
+
+ /* refresh IDENTIFY page if any _GTF command has been executed */
+ if (rc > 0) {
+ rc = ata_dev_reread_id(dev, 0);
+ if (rc < 0) {
+ ata_dev_printk(dev, KERN_ERR, "failed to IDENTIFY "
+ "after ACPI commands\n");
+ return rc;
+ }
+ }
+ return 0;
+
+ acpi_err:
+ /* let EH retry on the first failure, disable ACPI on the second */
+ if (dev->flags & ATA_DFLAG_ACPI_FAILED) {
+ ata_dev_printk(dev, KERN_WARNING, "ACPI on devcfg failed the "
+ "second time, disabling (errno=%d)\n", rc);
+
+ dev->acpi_handle = NULL;
+
+ /* if port is working, request IDENTIFY reload and continue */
+ if (!(ap->pflags & ATA_PFLAG_FROZEN))
+ rc = 1;
+ }
+ dev->flags |= ATA_DFLAG_ACPI_FAILED;
+ return rc;
+}
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 981b397..5b25311 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -1845,7 +1845,8 @@ static void ata_dev_config_ncq(struct ata_device *dev,
int ata_dev_configure(struct ata_device *dev)
{
struct ata_port *ap = dev->ap;
- int print_info = ap->eh_context.i.flags & ATA_EHI_PRINTINFO;
+ struct ata_eh_context *ehc = &ap->eh_context;
+ int print_info = ehc->i.flags & ATA_EHI_PRINTINFO;
const u16 *id = dev->id;
unsigned int xfer_mask;
char revbuf[7]; /* XYZ-99\0 */
@@ -1862,15 +1863,10 @@ int ata_dev_configure(struct ata_device *dev)
if (ata_msg_probe(ap))
ata_dev_printk(dev, KERN_DEBUG, "%s: ENTER\n", __FUNCTION__);
- /* set _SDD */
- rc = ata_acpi_push_id(dev);
- if (rc) {
- ata_dev_printk(dev, KERN_WARNING, "failed to set _SDD(%d)\n",
- rc);
- }
-
- /* retrieve and execute the ATA task file of _GTF */
- ata_acpi_exec_tfs(ap);
+ /* let ACPI work its magic */
+ rc = ata_acpi_on_devcfg(dev);
+ if (rc)
+ return rc;
/* print device capabilities */
if (ata_msg_probe(ap))
@@ -3359,7 +3355,7 @@ int ata_std_prereset(struct ata_port *ap, unsigned long deadline)
return 0;
/* if SATA, resume phy */
- if (ap->cbl == ATA_CBL_SATA) {
+ if (ap->flags & ATA_FLAG_SATA) {
rc = sata_phy_resume(ap, timing, deadline);
/* whine about phy resume failure but proceed */
if (rc && rc != -EOPNOTSUPP)
@@ -4107,6 +4103,68 @@ static void ata_fill_sg(struct ata_queued_cmd *qc)
}
/**
+ * ata_fill_sg_dumb - Fill PCI IDE PRD table
+ * @qc: Metadata associated with taskfile to be transferred
+ *
+ * Fill PCI IDE PRD (scatter-gather) table with segments
+ * associated with the current disk command. Perform the fill
+ * so that we avoid writing any length 64K records for
+ * controllers that don't follow the spec.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ *
+ */
+static void ata_fill_sg_dumb(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct scatterlist *sg;
+ unsigned int idx;
+
+ WARN_ON(qc->__sg == NULL);
+ WARN_ON(qc->n_elem == 0 && qc->pad_len == 0);
+
+ idx = 0;
+ ata_for_each_sg(sg, qc) {
+ u32 addr, offset;
+ u32 sg_len, len, blen;
+
+ /* determine if physical DMA addr spans 64K boundary.
+ * Note h/w doesn't support 64-bit, so we unconditionally
+ * truncate dma_addr_t to u32.
+ */
+ addr = (u32) sg_dma_address(sg);
+ sg_len = sg_dma_len(sg);
+
+ while (sg_len) {
+ offset = addr & 0xffff;
+ len = sg_len;
+ if ((offset + sg_len) > 0x10000)
+ len = 0x10000 - offset;
+
+ blen = len & 0xffff;
+ ap->prd[idx].addr = cpu_to_le32(addr);
+ if (blen == 0) {
+ /* Some PATA chipsets like the CS5530 can't
+ cope with 0x0000 meaning 64K as the spec says */
+ ap->prd[idx].flags_len = cpu_to_le32(0x8000);
+ blen = 0x8000;
+ ap->prd[++idx].addr = cpu_to_le32(addr + 0x8000);
+ }
+ ap->prd[idx].flags_len = cpu_to_le32(blen);
+ VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", idx, addr, len);
+
+ idx++;
+ sg_len -= len;
+ addr += len;
+ }
+ }
+
+ if (idx)
+ ap->prd[idx - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
+}
+
+/**
* ata_check_atapi_dma - Check whether ATAPI DMA can be supported
* @qc: Metadata associated with taskfile to check
*
@@ -4153,6 +4211,23 @@ void ata_qc_prep(struct ata_queued_cmd *qc)
ata_fill_sg(qc);
}
+/**
+ * ata_dumb_qc_prep - Prepare taskfile for submission
+ * @qc: Metadata associated with taskfile to be prepared
+ *
+ * Prepare ATA taskfile for submission.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void ata_dumb_qc_prep(struct ata_queued_cmd *qc)
+{
+ if (!(qc->flags & ATA_QCFLAG_DMAMAP))
+ return;
+
+ ata_fill_sg_dumb(qc);
+}
+
void ata_noop_qc_prep(struct ata_queued_cmd *qc) { }
/**
@@ -5660,7 +5735,7 @@ irqreturn_t ata_interrupt (int irq, void *dev_instance)
*/
int sata_scr_valid(struct ata_port *ap)
{
- return ap->cbl == ATA_CBL_SATA && ap->ops->scr_read;
+ return (ap->flags & ATA_FLAG_SATA) && ap->ops->scr_read;
}
/**
@@ -6293,6 +6368,9 @@ int ata_host_register(struct ata_host *host, struct scsi_host_template *sht)
if (rc)
return rc;
+ /* associate with ACPI nodes */
+ ata_acpi_associate(host);
+
/* set cable, sata_spd_limit and report */
for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap = host->ports[i];
@@ -6324,7 +6402,7 @@ int ata_host_register(struct ata_host *host, struct scsi_host_template *sht)
if (!ata_port_is_dummy(ap))
ata_port_printk(ap, KERN_INFO, "%cATA max %s cmd 0x%p "
"ctl 0x%p bmdma 0x%p irq %d\n",
- ap->cbl == ATA_CBL_SATA ? 'S' : 'P',
+ (ap->flags & ATA_FLAG_SATA) ? 'S' : 'P',
ata_mode_string(xfer_mask),
ap->ioaddr.cmd_addr,
ap->ioaddr.ctl_addr,
@@ -6822,6 +6900,7 @@ EXPORT_SYMBOL_GPL(ata_do_set_mode);
EXPORT_SYMBOL_GPL(ata_data_xfer);
EXPORT_SYMBOL_GPL(ata_data_xfer_noirq);
EXPORT_SYMBOL_GPL(ata_qc_prep);
+EXPORT_SYMBOL_GPL(ata_dumb_qc_prep);
EXPORT_SYMBOL_GPL(ata_noop_qc_prep);
EXPORT_SYMBOL_GPL(ata_bmdma_setup);
EXPORT_SYMBOL_GPL(ata_bmdma_start);
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index f7582c9..9ee0a8c 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -2154,19 +2154,25 @@ static void ata_eh_handle_port_suspend(struct ata_port *ap)
WARN_ON(ap->pflags & ATA_PFLAG_SUSPENDED);
+ /* tell ACPI we're suspending */
+ rc = ata_acpi_on_suspend(ap);
+ if (rc)
+ goto out;
+
/* suspend */
ata_eh_freeze_port(ap);
if (ap->ops->port_suspend)
rc = ap->ops->port_suspend(ap, ap->pm_mesg);
+ out:
/* report result */
spin_lock_irqsave(ap->lock, flags);
ap->pflags &= ~ATA_PFLAG_PM_PENDING;
if (rc == 0)
ap->pflags |= ATA_PFLAG_SUSPENDED;
- else
+ else if (ap->pflags & ATA_PFLAG_FROZEN)
ata_port_schedule_eh(ap);
if (ap->pm_result) {
@@ -2207,6 +2213,9 @@ static void ata_eh_handle_port_resume(struct ata_port *ap)
if (ap->ops->port_resume)
rc = ap->ops->port_resume(ap);
+ /* tell ACPI that we're resuming */
+ ata_acpi_on_resume(ap);
+
/* report result */
spin_lock_irqsave(ap->lock, flags);
ap->pflags &= ~(ATA_PFLAG_PM_PENDING | ATA_PFLAG_SUSPENDED);
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 4ddf00c..cfde22d 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -2620,7 +2620,7 @@ static unsigned int ata_scsi_pass_thru(struct ata_queued_cmd *qc)
ata_dev_printk(dev, KERN_WARNING,
"invalid multi_count %u ignored\n",
multi_count);
- }
+ }
/* READ/WRITE LONG use a non-standard sect_size */
qc->sect_size = ATA_SECT_SIZE;
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index 5e24666..ba17fc5 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -98,17 +98,15 @@ extern struct ata_port *ata_port_alloc(struct ata_host *host);
/* libata-acpi.c */
#ifdef CONFIG_ATA_ACPI
-extern int ata_acpi_exec_tfs(struct ata_port *ap);
-extern int ata_acpi_push_id(struct ata_device *dev);
+extern void ata_acpi_associate(struct ata_host *host);
+extern int ata_acpi_on_suspend(struct ata_port *ap);
+extern void ata_acpi_on_resume(struct ata_port *ap);
+extern int ata_acpi_on_devcfg(struct ata_device *adev);
#else
-static inline int ata_acpi_exec_tfs(struct ata_port *ap)
-{
- return 0;
-}
-static inline int ata_acpi_push_id(struct ata_device *dev)
-{
- return 0;
-}
+static inline void ata_acpi_associate(struct ata_host *host) { }
+static inline int ata_acpi_on_suspend(struct ata_port *ap) { return 0; }
+static inline void ata_acpi_on_resume(struct ata_port *ap) { }
+static inline int ata_acpi_on_devcfg(struct ata_device *adev) { return 0; }
#endif
/* libata-scsi.c */
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index 75e95bd..30c4276 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -520,14 +520,14 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const struct ata_port_info info_early = {
.sht = &ali_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.port_ops = &ali_early_port_ops
};
/* Revision 0x20 added DMA */
static const struct ata_port_info info_20 = {
.sht = &ali_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &ali_20_port_ops
@@ -535,7 +535,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
/* Revision 0x20 with support logic added UDMA */
static const struct ata_port_info info_20_udma = {
.sht = &ali_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x07, /* UDMA33 */
@@ -544,37 +544,37 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
/* Revision 0xC2 adds UDMA66 */
static const struct ata_port_info info_c2 = {
.sht = &ali_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x1f,
+ .udma_mask = ATA_UDMA4,
.port_ops = &ali_c2_port_ops
};
/* Revision 0xC3 is UDMA66 for now */
static const struct ata_port_info info_c3 = {
.sht = &ali_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x1f,
+ .udma_mask = ATA_UDMA4,
.port_ops = &ali_c2_port_ops
};
/* Revision 0xC4 is UDMA100 */
static const struct ata_port_info info_c4 = {
.sht = &ali_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ .udma_mask = ATA_UDMA5,
.port_ops = &ali_c2_port_ops
};
/* Revision 0xC5 is UDMA133 with LBA48 DMA */
static const struct ata_port_info info_c5 = {
.sht = &ali_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &ali_c5_port_ops
};
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index a16f629..b9c44c5 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -541,7 +541,7 @@ static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
static const struct ata_port_info info[10] = {
{ /* 0: AMD 7401 */
.sht = &amd_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07, /* No SWDMA */
.udma_mask = 0x07, /* UDMA 33 */
@@ -549,74 +549,74 @@ static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
},
{ /* 1: Early AMD7409 - no swdma */
.sht = &amd_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x1f, /* UDMA 66 */
+ .udma_mask = ATA_UDMA4, /* UDMA 66 */
.port_ops = &amd66_port_ops
},
{ /* 2: AMD 7409, no swdma errata */
.sht = &amd_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x1f, /* UDMA 66 */
+ .udma_mask = ATA_UDMA4, /* UDMA 66 */
.port_ops = &amd66_port_ops
},
{ /* 3: AMD 7411 */
.sht = &amd_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f, /* UDMA 100 */
+ .udma_mask = ATA_UDMA5, /* UDMA 100 */
.port_ops = &amd100_port_ops
},
{ /* 4: AMD 7441 */
.sht = &amd_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f, /* UDMA 100 */
+ .udma_mask = ATA_UDMA5, /* UDMA 100 */
.port_ops = &amd100_port_ops
},
{ /* 5: AMD 8111*/
.sht = &amd_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f, /* UDMA 133, no swdma */
+ .udma_mask = ATA_UDMA6, /* UDMA 133, no swdma */
.port_ops = &amd133_port_ops
},
{ /* 6: AMD 8111 UDMA 100 (Serenade) */
.sht = &amd_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f, /* UDMA 100, no swdma */
+ .udma_mask = ATA_UDMA5, /* UDMA 100, no swdma */
.port_ops = &amd133_port_ops
},
{ /* 7: Nvidia Nforce */
.sht = &amd_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f, /* UDMA 100 */
+ .udma_mask = ATA_UDMA5, /* UDMA 100 */
.port_ops = &nv100_port_ops
},
{ /* 8: Nvidia Nforce2 and later */
.sht = &amd_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f, /* UDMA 133, no swdma */
+ .udma_mask = ATA_UDMA6, /* UDMA 133, no swdma */
.port_ops = &nv133_port_ops
},
{ /* 9: AMD CS5536 (Geode companion) */
.sht = &amd_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f, /* UDMA 100 */
+ .udma_mask = ATA_UDMA5, /* UDMA 100 */
.port_ops = &amd100_port_ops
}
};
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
index 03b6ddd..ce589d9 100644
--- a/drivers/ata/pata_artop.c
+++ b/drivers/ata/pata_artop.c
@@ -416,7 +416,7 @@ static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
static int printed_version;
static const struct ata_port_info info_6210 = {
.sht = &artop_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA2,
@@ -424,7 +424,7 @@ static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
};
static const struct ata_port_info info_626x = {
.sht = &artop_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA4,
@@ -432,7 +432,7 @@ static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
};
static const struct ata_port_info info_626x_fast = {
.sht = &artop_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA5,
diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
index 8449146..80509be 100644
--- a/drivers/ata/pata_atiixp.c
+++ b/drivers/ata/pata_atiixp.c
@@ -270,7 +270,7 @@ static int atiixp_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.sht = &atiixp_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x06, /* No MWDMA0 support */
.udma_mask = 0x3F,
@@ -285,6 +285,7 @@ static const struct pci_device_id atiixp[] = {
{ PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP300_IDE), },
{ PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP400_IDE), },
{ PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP600_IDE), },
+ { PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP700_IDE), },
{ },
};
diff --git a/drivers/ata/pata_cmd640.c b/drivers/ata/pata_cmd640.c
index 31cbf8d..0feb5ae 100644
--- a/drivers/ata/pata_cmd640.c
+++ b/drivers/ata/pata_cmd640.c
@@ -251,7 +251,7 @@ static int cmd640_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.sht = &cmd640_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.port_ops = &cmd640_port_ops
};
diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c
index 320a5b1..dc443e7 100644
--- a/drivers/ata/pata_cmd64x.c
+++ b/drivers/ata/pata_cmd64x.c
@@ -380,21 +380,21 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
static const struct ata_port_info cmd_info[6] = {
{ /* CMD 643 - no UDMA */
.sht = &cmd64x_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &cmd64x_port_ops
},
{ /* CMD 646 with broken UDMA */
.sht = &cmd64x_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &cmd64x_port_ops
},
{ /* CMD 646 with working UDMA */
.sht = &cmd64x_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = ATA_UDMA1,
@@ -402,14 +402,14 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
},
{ /* CMD 646 rev 1 */
.sht = &cmd64x_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &cmd646r1_port_ops
},
{ /* CMD 648 */
.sht = &cmd64x_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = ATA_UDMA2,
@@ -417,7 +417,7 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
},
{ /* CMD 649 */
.sht = &cmd64x_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = ATA_UDMA3,
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c
index 00cf013..6bf037d 100644
--- a/drivers/ata/pata_cs5520.c
+++ b/drivers/ata/pata_cs5520.c
@@ -146,7 +146,7 @@ static struct scsi_host_template cs5520_sht = {
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
- .sg_tablesize = LIBATA_MAX_PRD,
+ .sg_tablesize = LIBATA_DUMB_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
@@ -178,7 +178,7 @@ static struct ata_port_operations cs5520_port_ops = {
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
- .qc_prep = ata_qc_prep,
+ .qc_prep = ata_dumb_qc_prep,
.qc_issue = ata_qc_issue_prot,
.data_xfer = ata_data_xfer,
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
index 848f030..3fca589 100644
--- a/drivers/ata/pata_cs5530.c
+++ b/drivers/ata/pata_cs5530.c
@@ -167,7 +167,7 @@ static struct scsi_host_template cs5530_sht = {
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
- .sg_tablesize = LIBATA_MAX_PRD,
+ .sg_tablesize = LIBATA_DUMB_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
@@ -201,7 +201,7 @@ static struct ata_port_operations cs5530_port_ops = {
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.cable_detect = ata_cable_40wire,
- .qc_prep = ata_qc_prep,
+ .qc_prep = ata_dumb_qc_prep,
.qc_issue = cs5530_qc_issue_prot,
.data_xfer = ata_data_xfer,
@@ -337,7 +337,7 @@ static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.sht = &cs5530_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x07,
@@ -346,7 +346,7 @@ static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
/* The docking connector doesn't do UDMA, and it seems not MWDMA */
static const struct ata_port_info info_palmax_secondary = {
.sht = &cs5530_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.port_ops = &cs5530_port_ops
};
diff --git a/drivers/ata/pata_cs5535.c b/drivers/ata/pata_cs5535.c
index aa3256f..360b6f3 100644
--- a/drivers/ata/pata_cs5535.c
+++ b/drivers/ata/pata_cs5535.c
@@ -225,10 +225,10 @@ static int cs5535_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.sht = &cs5535_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x1f,
+ .udma_mask = ATA_UDMA4,
.port_ops = &cs5535_port_ops
};
const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
diff --git a/drivers/ata/pata_cypress.c b/drivers/ata/pata_cypress.c
index d41a769..6cbc877 100644
--- a/drivers/ata/pata_cypress.c
+++ b/drivers/ata/pata_cypress.c
@@ -167,7 +167,7 @@ static int cy82c693_init_one(struct pci_dev *pdev, const struct pci_device_id *i
{
static const struct ata_port_info info = {
.sht = &cy82c693_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &cy82c693_port_ops
diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c
index 079248a..c8ba59c 100644
--- a/drivers/ata/pata_efar.c
+++ b/drivers/ata/pata_efar.c
@@ -303,7 +303,7 @@ static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
static int printed_version;
static const struct ata_port_info info = {
.sht = &efar_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma1-2 */
.udma_mask = 0x0f, /* UDMA 66 */
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index 0c9cb60..6f7d34a 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -393,10 +393,10 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info_hpt366 = {
.sht = &hpt36x_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x1f,
+ .udma_mask = ATA_UDMA4,
.port_ops = &hpt366_port_ops
};
struct ata_port_info info = info_hpt366;
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index a8c0cbe..b0af65a 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -889,25 +889,25 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
/* HPT370 - UDMA100 */
static const struct ata_port_info info_hpt370 = {
.sht = &hpt37x_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ .udma_mask = ATA_UDMA5,
.port_ops = &hpt370_port_ops
};
/* HPT370A - UDMA100 */
static const struct ata_port_info info_hpt370a = {
.sht = &hpt37x_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ .udma_mask = ATA_UDMA5,
.port_ops = &hpt370a_port_ops
};
/* HPT370 - UDMA100 */
static const struct ata_port_info info_hpt370_33 = {
.sht = &hpt37x_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x0f,
@@ -916,7 +916,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
/* HPT370A - UDMA100 */
static const struct ata_port_info info_hpt370a_33 = {
.sht = &hpt37x_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x0f,
@@ -925,19 +925,19 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
/* HPT371, 372 and friends - UDMA133 */
static const struct ata_port_info info_hpt372 = {
.sht = &hpt37x_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &hpt372_port_ops
};
/* HPT374 - UDMA100 */
static const struct ata_port_info info_hpt374 = {
.sht = &hpt37x_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ .udma_mask = ATA_UDMA5,
.port_ops = &hpt374_port_ops
};
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index e947433..aa29cde 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -490,10 +490,10 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
/* HPT372N and friends - UDMA133 */
static const struct ata_port_info info = {
.sht = &hpt3x2n_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &hpt3x2n_port_ops
};
struct ata_port_info port = info;
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
index 8ce5e23..d928c91 100644
--- a/drivers/ata/pata_hpt3x3.c
+++ b/drivers/ata/pata_hpt3x3.c
@@ -173,7 +173,7 @@ static int hpt3x3_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.sht = &hpt3x3_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x07,
diff --git a/drivers/ata/pata_icside.c b/drivers/ata/pata_icside.c
index c791a46..321d98b 100644
--- a/drivers/ata/pata_icside.c
+++ b/drivers/ata/pata_icside.c
@@ -530,7 +530,7 @@ static int __devinit pata_icside_add_ports(struct pata_icside_info *info)
ap->pio_mask = 0x1f;
ap->mwdma_mask = info->mwdma_mask;
- ap->flags |= ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST;
+ ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->ops = &pata_icside_port_ops;
pata_icside_setup_ioaddr(&ap->ioaddr, info->base, info->port[i]);
diff --git a/drivers/ata/pata_it8213.c b/drivers/ata/pata_it8213.c
index 95b0bb6..b8af55e 100644
--- a/drivers/ata/pata_it8213.c
+++ b/drivers/ata/pata_it8213.c
@@ -313,10 +313,10 @@ static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *en
static int printed_version;
static const struct ata_port_info info = {
.sht = &it8213_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x1f, /* UDMA 100 */
+ .udma_mask = ATA_UDMA4, /* FIXME: want UDMA 100? */
.port_ops = &it8213_ops,
};
/* Current IT8213 stuff is single port */
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
index 12c6e08..b67bbf6 100644
--- a/drivers/ata/pata_it821x.c
+++ b/drivers/ata/pata_it821x.c
@@ -714,17 +714,17 @@ static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
static const struct ata_port_info info_smart = {
.sht = &it821x_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &it821x_smart_port_ops
};
static const struct ata_port_info info_passthru = {
.sht = &it821x_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &it821x_passthru_port_ops
};
diff --git a/drivers/ata/pata_ixp4xx_cf.c b/drivers/ata/pata_ixp4xx_cf.c
index 8d2bc1e..4ca7fd6 100644
--- a/drivers/ata/pata_ixp4xx_cf.c
+++ b/drivers/ata/pata_ixp4xx_cf.c
@@ -1,13 +1,14 @@
/*
* ixp4xx PATA/Compact Flash driver
- * Copyright (c) 2006 Tower Technologies
+ * Copyright (C) 2006-07 Tower Technologies
* Author: Alessandro Zummo <a.zummo@towertech.it>
*
* An ATA driver to handle a Compact Flash connected
* to the ixp4xx expansion bus in TrueIDE mode. The CF
* must have it chip selects connected to two CS lines
- * on the ixp4xx. The interrupt line is optional, if not
- * specified the driver will run in polling mode.
+ * on the ixp4xx. In the irq is not available, you might
+ * want to modify both this driver and libata to run in
+ * polling mode.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -23,7 +24,7 @@
#include <scsi/scsi_host.h>
#define DRV_NAME "pata_ixp4xx_cf"
-#define DRV_VERSION "0.1.3"
+#define DRV_VERSION "0.2"
static int ixp4xx_set_mode(struct ata_port *ap, struct ata_device **error)
{
@@ -42,13 +43,6 @@ static int ixp4xx_set_mode(struct ata_port *ap, struct ata_device **error)
return 0;
}
-static void ixp4xx_phy_reset(struct ata_port *ap)
-{
- ap->cbl = ATA_CBL_PATA40;
- ata_port_probe(ap);
- ata_bus_reset(ap);
-}
-
static void ixp4xx_mmio_data_xfer(struct ata_device *adev, unsigned char *buf,
unsigned int buflen, int write_data)
{
@@ -56,7 +50,7 @@ static void ixp4xx_mmio_data_xfer(struct ata_device *adev, unsigned char *buf,
unsigned int words = buflen >> 1;
u16 *buf16 = (u16 *) buf;
struct ata_port *ap = adev->ap;
- void __iomem *mmio = (void __iomem *)ap->ioaddr.data_addr;
+ void __iomem *mmio = ap->ioaddr.data_addr;
struct ixp4xx_pata_data *data = ap->host->dev->platform_data;
/* set the expansion bus in 16bit mode and restore
@@ -92,10 +86,6 @@ static void ixp4xx_mmio_data_xfer(struct ata_device *adev, unsigned char *buf,
*data->cs0_cfg |= 0x01;
}
-static void ixp4xx_irq_clear(struct ata_port *ap)
-{
-}
-
static struct scsi_host_template ixp4xx_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
@@ -115,29 +105,32 @@ static struct scsi_host_template ixp4xx_sht = {
};
static struct ata_port_operations ixp4xx_port_ops = {
- .set_mode = ixp4xx_set_mode,
- .mode_filter = ata_pci_default_filter,
-
- .port_disable = ata_port_disable,
- .tf_load = ata_tf_load,
- .tf_read = ata_tf_read,
- .check_status = ata_check_status,
- .exec_command = ata_exec_command,
- .dev_select = ata_std_dev_select,
-
- .qc_prep = ata_qc_prep,
- .qc_issue = ata_qc_issue_prot,
- .eng_timeout = ata_eng_timeout,
- .data_xfer = ixp4xx_mmio_data_xfer,
- .cable_detect = ata_cable_40wire,
-
- .irq_clear = ixp4xx_irq_clear,
- .irq_on = ata_irq_on,
- .irq_ack = ata_irq_ack,
-
- .port_start = ata_port_start,
-
- .phy_reset = ixp4xx_phy_reset,
+ .set_mode = ixp4xx_set_mode,
+ .mode_filter = ata_pci_default_filter,
+
+ .port_disable = ata_port_disable,
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .exec_command = ata_exec_command,
+ .check_status = ata_check_status,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = ata_bmdma_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ixp4xx_mmio_data_xfer,
+ .cable_detect = ata_cable_40wire,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_dummy_irq_ack,
+
+ .port_start = ata_port_start,
};
static void ixp4xx_setup_port(struct ata_ioports *ioaddr,
@@ -178,7 +171,6 @@ static __devinit int ixp4xx_pata_probe(struct platform_device *pdev)
struct ata_host *host;
struct ata_port *ap;
struct ixp4xx_pata_data *data = pdev->dev.platform_data;
- int rc;
cs0 = platform_get_resource(pdev, IORESOURCE_MEM, 0);
cs1 = platform_get_resource(pdev, IORESOURCE_MEM, 1);
@@ -211,10 +203,6 @@ static __devinit int ixp4xx_pata_probe(struct platform_device *pdev)
ap->pio_mask = 0x1f; /* PIO4 */
ap->flags |= ATA_FLAG_MMIO | ATA_FLAG_NO_LEGACY | ATA_FLAG_NO_ATAPI;
- /* run in polling mode if no irq has been assigned */
- if (!irq)
- ap->flags |= ATA_FLAG_PIO_POLLING;
-
ixp4xx_setup_port(&ap->ioaddr, data);
dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
index 2af7ff8..4d67f23 100644
--- a/drivers/ata/pata_jmicron.c
+++ b/drivers/ata/pata_jmicron.c
@@ -193,11 +193,11 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i
{
static const struct ata_port_info info = {
.sht = &jmicron_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ .udma_mask = ATA_UDMA5,
.port_ops = &jmicron_ops,
};
diff --git a/drivers/ata/pata_marvell.c b/drivers/ata/pata_marvell.c
index edbfe0d..87594c0 100644
--- a/drivers/ata/pata_marvell.c
+++ b/drivers/ata/pata_marvell.c
@@ -163,22 +163,22 @@ static int marvell_init_one (struct pci_dev *pdev, const struct pci_device_id *i
{
static const struct ata_port_info info = {
.sht = &marvell_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ .udma_mask = ATA_UDMA5,
.port_ops = &marvell_ops,
};
static const struct ata_port_info info_sata = {
.sht = &marvell_sht,
/* Slave possible as its magically mapped not real */
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &marvell_ops,
};
diff --git a/drivers/ata/pata_netcell.c b/drivers/ata/pata_netcell.c
index 81f5634..40eb574 100644
--- a/drivers/ata/pata_netcell.c
+++ b/drivers/ata/pata_netcell.c
@@ -94,12 +94,12 @@ static int netcell_init_one (struct pci_dev *pdev, const struct pci_device_id *e
static int printed_version;
static const struct ata_port_info info = {
.sht = &netcell_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
/* Actually we don't really care about these as the
firmware deals with it */
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x3f, /* UDMA 133 */
+ .udma_mask = ATA_UDMA5, /* UDMA 133 */
.port_ops = &netcell_ops,
};
const struct ata_port_info *port_info[] = { &info, NULL };
diff --git a/drivers/ata/pata_ns87410.c b/drivers/ata/pata_ns87410.c
index ea70ec7..2f5d714 100644
--- a/drivers/ata/pata_ns87410.c
+++ b/drivers/ata/pata_ns87410.c
@@ -193,7 +193,7 @@ static int ns87410_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.sht = &ns87410_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x0F,
.port_ops = &ns87410_port_ops
};
diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c
index 29c23dd..091a70a 100644
--- a/drivers/ata/pata_oldpiix.c
+++ b/drivers/ata/pata_oldpiix.c
@@ -291,7 +291,7 @@ static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *e
static int printed_version;
static const struct ata_port_info info = {
.sht = &oldpiix_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma1-2 */
.port_ops = &oldpiix_pata_ops,
diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c
index 1c44653..458bf67 100644
--- a/drivers/ata/pata_opti.c
+++ b/drivers/ata/pata_opti.c
@@ -218,7 +218,7 @@ static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.sht = &opti_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.port_ops = &opti_port_ops
};
diff --git a/drivers/ata/pata_optidma.c b/drivers/ata/pata_optidma.c
index 3093b02..f89bdfd 100644
--- a/drivers/ata/pata_optidma.c
+++ b/drivers/ata/pata_optidma.c
@@ -484,14 +484,14 @@ static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info_82c700 = {
.sht = &optidma_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &optidma_port_ops
};
static const struct ata_port_info info_82c700_udma = {
.sht = &optidma_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x07,
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c
index d277246..92447be 100644
--- a/drivers/ata/pata_pdc202xx_old.c
+++ b/drivers/ata/pata_pdc202xx_old.c
@@ -320,7 +320,7 @@ static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id
static const struct ata_port_info info[3] = {
{
.sht = &pdc202xx_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = ATA_UDMA2,
@@ -328,7 +328,7 @@ static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id
},
{
.sht = &pdc202xx_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = ATA_UDMA4,
@@ -336,7 +336,7 @@ static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id
},
{
.sht = &pdc202xx_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = ATA_UDMA5,
diff --git a/drivers/ata/pata_platform.c b/drivers/ata/pata_platform.c
index cbb7866..79f841b 100644
--- a/drivers/ata/pata_platform.c
+++ b/drivers/ata/pata_platform.c
@@ -139,6 +139,7 @@ static int __devinit pata_platform_probe(struct platform_device *pdev)
struct resource *io_res, *ctl_res;
struct ata_host *host;
struct ata_port *ap;
+ struct pata_platform_info *pp_info;
unsigned int mmio;
/*
@@ -208,11 +209,12 @@ static int __devinit pata_platform_probe(struct platform_device *pdev)
ap->ioaddr.altstatus_addr = ap->ioaddr.ctl_addr;
- pata_platform_setup_port(&ap->ioaddr, pdev->dev.platform_data);
+ pp_info = (struct pata_platform_info *)(pdev->dev.platform_data);
+ pata_platform_setup_port(&ap->ioaddr, pp_info);
/* activate */
return ata_host_activate(host, platform_get_irq(pdev, 0), ata_interrupt,
- 0, &pata_platform_sht);
+ pp_info->irq_flags, &pata_platform_sht);
}
/**
diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c
index ba96b54..7d1aabe 100644
--- a/drivers/ata/pata_radisys.c
+++ b/drivers/ata/pata_radisys.c
@@ -257,7 +257,7 @@ static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *e
static int printed_version;
static const struct ata_port_info info = {
.sht = &radisys_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma1-2 */
.udma_mask = 0x14, /* UDMA33/66 only */
diff --git a/drivers/ata/pata_rz1000.c b/drivers/ata/pata_rz1000.c
index a3488b4..7632fcb 100644
--- a/drivers/ata/pata_rz1000.c
+++ b/drivers/ata/pata_rz1000.c
@@ -133,7 +133,7 @@ static int rz1000_init_one (struct pci_dev *pdev, const struct pci_device_id *en
static int printed_version;
static const struct ata_port_info info = {
.sht = &rz1000_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.port_ops = &rz1000_port_ops
};
diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c
index 1233063..b8b2d11 100644
--- a/drivers/ata/pata_sc1200.c
+++ b/drivers/ata/pata_sc1200.c
@@ -185,7 +185,7 @@ static struct scsi_host_template sc1200_sht = {
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
- .sg_tablesize = LIBATA_MAX_PRD,
+ .sg_tablesize = LIBATA_DUMB_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
@@ -219,7 +219,7 @@ static struct ata_port_operations sc1200_port_ops = {
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
- .qc_prep = ata_qc_prep,
+ .qc_prep = ata_dumb_qc_prep,
.qc_issue = sc1200_qc_issue_prot,
.data_xfer = ata_data_xfer,
@@ -245,7 +245,7 @@ static int sc1200_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.sht = &sc1200_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x07,
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c
index 1e8f421..0231aba 100644
--- a/drivers/ata/pata_serverworks.c
+++ b/drivers/ata/pata_serverworks.c
@@ -478,31 +478,31 @@ static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id
static const struct ata_port_info info[4] = {
{ /* OSB4 */
.sht = &serverworks_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x07,
.port_ops = &serverworks_osb4_port_ops
}, { /* OSB4 no UDMA */
.sht = &serverworks_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x00,
.port_ops = &serverworks_osb4_port_ops
}, { /* CSB5 */
.sht = &serverworks_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x1f,
+ .udma_mask = ATA_UDMA4,
.port_ops = &serverworks_csb_port_ops
}, { /* CSB5 - later revisions*/
.sht = &serverworks_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ .udma_mask = ATA_UDMA5,
.port_ops = &serverworks_csb_port_ops
}
};
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index 440e2cb..b0cd52d 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -35,6 +35,8 @@
#define DRV_NAME "pata_sil680"
#define DRV_VERSION "0.4.6"
+#define SIL680_MMIO_BAR 5
+
/**
* sil680_selreg - return register base
* @hwif: interface
@@ -293,8 +295,8 @@ static u8 sil680_init_chip(struct pci_dev *pdev)
pci_read_config_byte(pdev, 0x8A, &tmpbyte);
- printk(KERN_INFO "sil680: BA5_EN = %d clock = %02X\n",
- tmpbyte & 1, tmpbyte & 0x30);
+ dev_dbg(&pdev->dev, "sil680: BA5_EN = %d clock = %02X\n",
+ tmpbyte & 1, tmpbyte & 0x30);
switch(tmpbyte & 0x30) {
case 0x00:
@@ -315,8 +317,8 @@ static u8 sil680_init_chip(struct pci_dev *pdev)
}
pci_read_config_byte(pdev, 0x8A, &tmpbyte);
- printk(KERN_INFO "sil680: BA5_EN = %d clock = %02X\n",
- tmpbyte & 1, tmpbyte & 0x30);
+ dev_dbg(&pdev->dev, "sil680: BA5_EN = %d clock = %02X\n",
+ tmpbyte & 1, tmpbyte & 0x30);
pci_write_config_byte(pdev, 0xA1, 0x72);
pci_write_config_word(pdev, 0xA2, 0x328A);
@@ -339,22 +341,23 @@ static u8 sil680_init_chip(struct pci_dev *pdev)
return tmpbyte & 0x30;
}
-static int sil680_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+static int __devinit sil680_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.sht = &sil680_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &sil680_port_ops
};
static const struct ata_port_info info_slow = {
.sht = &sil680_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ .udma_mask = ATA_UDMA5,
.port_ops = &sil680_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index cfe4ec6..2b45082 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -732,7 +732,7 @@ static const struct ata_port_operations sis_old_ops = {
static const struct ata_port_info sis_info = {
.sht = &sis_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07,
.udma_mask = 0,
@@ -740,7 +740,7 @@ static const struct ata_port_info sis_info = {
};
static const struct ata_port_info sis_info33 = {
.sht = &sis_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07,
.udma_mask = ATA_UDMA2, /* UDMA 33 */
@@ -748,28 +748,28 @@ static const struct ata_port_info sis_info33 = {
};
static const struct ata_port_info sis_info66 = {
.sht = &sis_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA4, /* UDMA 66 */
.port_ops = &sis_66_ops,
};
static const struct ata_port_info sis_info100 = {
.sht = &sis_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA5,
.port_ops = &sis_100_ops,
};
static const struct ata_port_info sis_info100_early = {
.sht = &sis_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.udma_mask = ATA_UDMA5,
.pio_mask = 0x1f, /* pio0-4 */
.port_ops = &sis_66_ops,
};
static const struct ata_port_info sis_info133 = {
.sht = &sis_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &sis_133_ops,
@@ -783,7 +783,7 @@ const struct ata_port_info sis_info133_for_sata = {
};
static const struct ata_port_info sis_info133_early = {
.sht = &sis_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &sis_133_early_ops,
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index e5aaec4..bde7341 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -303,14 +303,14 @@ static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id
{
static const struct ata_port_info info_dma = {
.sht = &sl82c105_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &sl82c105_port_ops
};
static const struct ata_port_info info_early = {
.sht = &sl82c105_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.port_ops = &sl82c105_port_ops
};
diff --git a/drivers/ata/pata_triflex.c b/drivers/ata/pata_triflex.c
index b1d3076..af21f44 100644
--- a/drivers/ata/pata_triflex.c
+++ b/drivers/ata/pata_triflex.c
@@ -235,7 +235,7 @@ static int triflex_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.sht = &triflex_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &triflex_port_ops
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 63eca29..f0cadbe 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -471,7 +471,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7,
+ .udma_mask = ATA_UDMA2,
.port_ops = &via_port_ops
};
/* VIA UDMA 66 devices */
@@ -480,7 +480,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x1f,
+ .udma_mask = ATA_UDMA4,
.port_ops = &via_port_ops
};
/* VIA UDMA 100 devices */
@@ -489,7 +489,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ .udma_mask = ATA_UDMA5,
.port_ops = &via_port_ops
};
/* UDMA133 with bad AST (All current 133) */
@@ -498,7 +498,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f, /* FIXME: should check north bridge */
+ .udma_mask = ATA_UDMA6, /* FIXME: should check north bridge */
.port_ops = &via_port_ops
};
struct ata_port_info type;
diff --git a/drivers/ata/pdc_adma.c b/drivers/ata/pdc_adma.c
index f12c2b6..bec1de5 100644
--- a/drivers/ata/pdc_adma.c
+++ b/drivers/ata/pdc_adma.c
@@ -145,32 +145,32 @@ static struct scsi_host_template adma_ata_sht = {
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
+ .slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
+ .bios_param = ata_std_bios_param,
+ .proc_name = DRV_NAME,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
+ .dma_boundary = ADMA_DMA_BOUNDARY,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
- .emulated = ATA_SHT_EMULATED,
.use_clustering = ENABLE_CLUSTERING,
- .proc_name = DRV_NAME,
- .dma_boundary = ADMA_DMA_BOUNDARY,
- .slave_configure = ata_scsi_slave_config,
- .slave_destroy = ata_scsi_slave_destroy,
- .bios_param = ata_std_bios_param,
+ .emulated = ATA_SHT_EMULATED,
};
static const struct ata_port_operations adma_ata_ops = {
.port_disable = ata_port_disable,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
- .check_status = ata_check_status,
- .check_atapi_dma = adma_check_atapi_dma,
.exec_command = ata_exec_command,
+ .check_status = ata_check_status,
.dev_select = ata_std_dev_select,
.phy_reset = adma_phy_reset,
+ .check_atapi_dma = adma_check_atapi_dma,
+ .data_xfer = ata_data_xfer,
.qc_prep = adma_qc_prep,
.qc_issue = adma_qc_issue,
.eng_timeout = adma_eng_timeout,
- .data_xfer = ata_data_xfer,
.irq_clear = adma_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
@@ -188,7 +188,7 @@ static struct ata_port_info adma_port_info[] = {
ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO |
ATA_FLAG_PIO_POLLING,
.pio_mask = 0x10, /* pio4 */
- .udma_mask = 0x1f, /* udma0-4 */
+ .udma_mask = ATA_UDMA4,
.port_ops = &adma_ata_ops,
},
};
diff --git a/drivers/ata/sata_inic162x.c b/drivers/ata/sata_inic162x.c
index dc3bbce..3de1834 100644
--- a/drivers/ata/sata_inic162x.c
+++ b/drivers/ata/sata_inic162x.c
@@ -192,7 +192,7 @@ static void inic_reset_port(void __iomem *port_base)
static u32 inic_scr_read(struct ata_port *ap, unsigned sc_reg)
{
- void __iomem *scr_addr = (void __iomem *)ap->ioaddr.scr_addr;
+ void __iomem *scr_addr = ap->ioaddr.scr_addr;
void __iomem *addr;
u32 val;
@@ -210,7 +210,7 @@ static u32 inic_scr_read(struct ata_port *ap, unsigned sc_reg)
static void inic_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val)
{
- void __iomem *scr_addr = (void __iomem *)ap->ioaddr.scr_addr;
+ void __iomem *scr_addr = ap->ioaddr.scr_addr;
void __iomem *addr;
if (unlikely(sc_reg >= ARRAY_SIZE(scr_map)))
@@ -594,7 +594,7 @@ static struct ata_port_info inic_port_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_PIO_DMA,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &inic_port_ops
};
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 590f2f9..3873b29 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -526,44 +526,44 @@ static const struct ata_port_info mv_port_info[] = {
{ /* chip_504x */
.flags = MV_COMMON_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_508x */
.flags = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC),
.pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_5080 */
.flags = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC),
.pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_604x */
.flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS),
.pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &mv6_ops,
},
{ /* chip_608x */
.flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS |
MV_FLAG_DUAL_HC),
.pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &mv6_ops,
},
{ /* chip_6042 */
.flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS),
.pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
{ /* chip_7042 */
.flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS),
.pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
};
@@ -2338,7 +2338,7 @@ static void mv_print_info(struct ata_host *host)
struct pci_dev *pdev = to_pci_dev(host->dev);
struct mv_host_priv *hpriv = host->private_data;
u8 rev_id, scc;
- const char *scc_s;
+ const char *scc_s, *gen;
/* Use this to determine the HW stepping of the chip so we know
* what errata to workaround
@@ -2351,11 +2351,20 @@ static void mv_print_info(struct ata_host *host)
else if (scc == 0x01)
scc_s = "RAID";
else
- scc_s = "unknown";
+ scc_s = "?";
+
+ if (IS_GEN_I(hpriv))
+ gen = "I";
+ else if (IS_GEN_II(hpriv))
+ gen = "II";
+ else if (IS_GEN_IIE(hpriv))
+ gen = "IIE";
+ else
+ gen = "?";
dev_printk(KERN_INFO, &pdev->dev,
- "%u slots %u ports %s mode IRQ via %s\n",
- (unsigned)MV_MAX_Q_DEPTH, host->n_ports,
+ "Gen-%s %u slots %u ports %s mode IRQ via %s\n",
+ gen, (unsigned)MV_MAX_Q_DEPTH, host->n_ports,
scc_s, (MV_HP_FLAG_MSI & hpriv->hp_flags) ? "MSI" : "INTx");
}
diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c
index 6dc0b01..2ad5872 100644
--- a/drivers/ata/sata_promise.c
+++ b/drivers/ata/sata_promise.c
@@ -45,8 +45,7 @@
#include "sata_promise.h"
#define DRV_NAME "sata_promise"
-#define DRV_VERSION "2.07"
-
+#define DRV_VERSION "2.08"
enum {
PDC_MAX_PORTS = 4,
@@ -94,7 +93,7 @@ enum {
board_20319 = 2, /* FastTrak S150 TX4 */
board_20619 = 3, /* FastTrak TX4000 */
board_2057x = 4, /* SATAII150 Tx2plus */
- board_2057x_pata = 5, /* SATAII150 Tx2plus */
+ board_2057x_pata = 5, /* SATAII150 Tx2plus PATA port */
board_40518 = 6, /* SATAII150 Tx4 */
PDC_HAS_PATA = (1 << 1), /* PDC20375/20575 has PATA */
@@ -124,7 +123,6 @@ enum {
PDC_FLAG_4_PORTS = (1 << 26), /* 4 ports */
};
-
struct pdc_port_priv {
u8 *pkt;
dma_addr_t pkt_dma;
@@ -252,7 +250,7 @@ static const struct ata_port_info pdc_port_info[] = {
PDC_FLAG_SATA_PATA,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .udma_mask = ATA_UDMA6,
.port_ops = &pdc_old_sata_ops,
},
@@ -261,7 +259,7 @@ static const struct ata_port_info pdc_port_info[] = {
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .udma_mask = ATA_UDMA6,
.port_ops = &pdc_pata_ops,
},
@@ -271,7 +269,7 @@ static const struct ata_port_info pdc_port_info[] = {
PDC_FLAG_4_PORTS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .udma_mask = ATA_UDMA6,
.port_ops = &pdc_old_sata_ops,
},
@@ -281,7 +279,7 @@ static const struct ata_port_info pdc_port_info[] = {
PDC_FLAG_4_PORTS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .udma_mask = ATA_UDMA6,
.port_ops = &pdc_pata_ops,
},
@@ -291,7 +289,7 @@ static const struct ata_port_info pdc_port_info[] = {
PDC_FLAG_GEN_II | PDC_FLAG_SATA_PATA,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .udma_mask = ATA_UDMA6,
.port_ops = &pdc_sata_ops,
},
@@ -301,7 +299,7 @@ static const struct ata_port_info pdc_port_info[] = {
PDC_FLAG_GEN_II,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .udma_mask = ATA_UDMA6,
.port_ops = &pdc_pata_ops,
},
@@ -311,7 +309,7 @@ static const struct ata_port_info pdc_port_info[] = {
PDC_FLAG_GEN_II | PDC_FLAG_4_PORTS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .udma_mask = ATA_UDMA6,
.port_ops = &pdc_sata_ops,
},
};
@@ -340,7 +338,6 @@ static const struct pci_device_id pdc_ata_pci_tbl[] = {
{ } /* terminate list */
};
-
static struct pci_driver pdc_ata_pci_driver = {
.name = DRV_NAME,
.id_table = pdc_ata_pci_tbl,
@@ -348,7 +345,6 @@ static struct pci_driver pdc_ata_pci_driver = {
.remove = ata_pci_remove_one,
};
-
static int pdc_common_port_start(struct ata_port *ap)
{
struct device *dev = ap->host->dev;
@@ -382,7 +378,7 @@ static int pdc_sata_port_start(struct ata_port *ap)
/* fix up PHYMODE4 align timing */
if (ap->flags & PDC_FLAG_GEN_II) {
- void __iomem *mmio = (void __iomem *) ap->ioaddr.scr_addr;
+ void __iomem *mmio = ap->ioaddr.scr_addr;
unsigned int tmp;
tmp = readl(mmio + 0x014);
@@ -418,7 +414,7 @@ static void pdc_reset_port(struct ata_port *ap)
static int pdc_pata_cable_detect(struct ata_port *ap)
{
u8 tmp;
- void __iomem *mmio = (void __iomem *) ap->ioaddr.cmd_addr + PDC_CTLSTAT + 0x03;
+ void __iomem *mmio = ap->ioaddr.cmd_addr + PDC_CTLSTAT + 0x03;
tmp = readb(mmio);
if (tmp & 0x01)
@@ -438,7 +434,6 @@ static u32 pdc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
return readl(ap->ioaddr.scr_addr + (sc_reg * 4));
}
-
static void pdc_sata_scr_write (struct ata_port *ap, unsigned int sc_reg,
u32 val)
{
@@ -573,7 +568,7 @@ static void pdc_qc_prep(struct ata_queued_cmd *qc)
static void pdc_freeze(struct ata_port *ap)
{
- void __iomem *mmio = (void __iomem *) ap->ioaddr.cmd_addr;
+ void __iomem *mmio = ap->ioaddr.cmd_addr;
u32 tmp;
tmp = readl(mmio + PDC_CTLSTAT);
@@ -585,7 +580,7 @@ static void pdc_freeze(struct ata_port *ap)
static void pdc_thaw(struct ata_port *ap)
{
- void __iomem *mmio = (void __iomem *) ap->ioaddr.cmd_addr;
+ void __iomem *mmio = ap->ioaddr.cmd_addr;
u32 tmp;
/* clear IRQ */
@@ -657,8 +652,8 @@ static void pdc_error_intr(struct ata_port *ap, struct ata_queued_cmd *qc,
ata_port_abort(ap);
}
-static inline unsigned int pdc_host_intr( struct ata_port *ap,
- struct ata_queued_cmd *qc)
+static inline unsigned int pdc_host_intr(struct ata_port *ap,
+ struct ata_queued_cmd *qc)
{
unsigned int handled = 0;
void __iomem *port_mmio = ap->ioaddr.cmd_addr;
@@ -685,10 +680,10 @@ static inline unsigned int pdc_host_intr( struct ata_port *ap,
handled = 1;
break;
- default:
+ default:
ap->stats.idle_irq++;
break;
- }
+ }
return handled;
}
@@ -701,6 +696,18 @@ static void pdc_irq_clear(struct ata_port *ap)
readl(mmio + PDC_INT_SEQMASK);
}
+static inline int pdc_is_sataii_tx4(unsigned long flags)
+{
+ const unsigned long mask = PDC_FLAG_GEN_II | PDC_FLAG_4_PORTS;
+ return (flags & mask) == mask;
+}
+
+static inline unsigned int pdc_port_no_to_ata_no(unsigned int port_no, int is_sataii_tx4)
+{
+ static const unsigned char sataii_tx4_port_remap[4] = { 3, 1, 0, 2};
+ return is_sataii_tx4 ? sataii_tx4_port_remap[port_no] : port_no;
+}
+
static irqreturn_t pdc_interrupt (int irq, void *dev_instance)
{
struct ata_host *host = dev_instance;
@@ -807,7 +814,6 @@ static void pdc_tf_load_mmio(struct ata_port *ap, const struct ata_taskfile *tf)
ata_tf_load(ap, tf);
}
-
static void pdc_exec_command_mmio(struct ata_port *ap, const struct ata_taskfile *tf)
{
WARN_ON (tf->protocol == ATA_PROT_DMA ||
@@ -867,7 +873,6 @@ static void pdc_ata_setup_port(struct ata_port *ap,
ap->ioaddr.scr_addr = scr_addr;
}
-
static void pdc_host_init(struct ata_host *host)
{
void __iomem *mmio = host->iomap[PDC_MMIO_BAR];
@@ -955,10 +960,8 @@ static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *e
if (pi->flags & PDC_FLAG_SATA_PATA) {
u8 tmp = readb(base + PDC_FLASH_CTL+1);
- if (!(tmp & 0x80)) {
+ if (!(tmp & 0x80))
ppi[n_ports++] = pi + 1;
- dev_printk(KERN_INFO, &pdev->dev, "PATA port found\n");
- }
}
host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports);
@@ -968,22 +971,12 @@ static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *e
}
host->iomap = pcim_iomap_table(pdev);
- is_sataii_tx4 = 0;
- if ((pi->flags & (PDC_FLAG_GEN_II|PDC_FLAG_4_PORTS)) == (PDC_FLAG_GEN_II|PDC_FLAG_4_PORTS)) {
- is_sataii_tx4 = 1;
- dev_printk(KERN_INFO, &pdev->dev, "applying SATAII TX4 port numbering workaround\n");
- }
+ is_sataii_tx4 = pdc_is_sataii_tx4(pi->flags);
for (i = 0; i < host->n_ports; i++) {
- static const unsigned char sataii_tx4_port_remap[4] = { 3, 1, 0, 2};
- int ata_nr;
-
- ata_nr = i;
- if (is_sataii_tx4)
- ata_nr = sataii_tx4_port_remap[i];
-
+ unsigned int ata_no = pdc_port_no_to_ata_no(i, is_sataii_tx4);
pdc_ata_setup_port(host->ports[i],
- base + 0x200 + ata_nr * 0x80,
- base + 0x400 + ata_nr * 0x100);
+ base + 0x200 + ata_no * 0x80,
+ base + 0x400 + ata_no * 0x100);
}
/* initialize adapter */
@@ -1002,19 +995,16 @@ static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *e
&pdc_ata_sht);
}
-
static int __init pdc_ata_init(void)
{
return pci_register_driver(&pdc_ata_pci_driver);
}
-
static void __exit pdc_ata_exit(void)
{
pci_unregister_driver(&pdc_ata_pci_driver);
}
-
MODULE_AUTHOR("Jeff Garzik");
MODULE_DESCRIPTION("Promise ATA TX2/TX4/TX4000 low-level driver");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/sata_qstor.c b/drivers/ata/sata_qstor.c
index 6688ccb..9ab554d 100644
--- a/drivers/ata/sata_qstor.c
+++ b/drivers/ata/sata_qstor.c
@@ -176,7 +176,7 @@ static const struct ata_port_info qs_port_info[] = {
//FIXME ATA_FLAG_SRST |
ATA_FLAG_MMIO | ATA_FLAG_PIO_POLLING,
.pio_mask = 0x10, /* pio4 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &qs_ata_ops,
},
};
diff --git a/drivers/ata/sata_sil.c b/drivers/ata/sata_sil.c
index a3b339b..2a86dc4 100644
--- a/drivers/ata/sata_sil.c
+++ b/drivers/ata/sata_sil.c
@@ -218,7 +218,7 @@ static const struct ata_port_info sil_port_info[] = {
.flags = SIL_DFL_PORT_FLAGS | SIL_FLAG_MOD15WRITE,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x3f, /* udma0-5 */
+ .udma_mask = ATA_UDMA5,
.port_ops = &sil_ops,
},
/* sil_3112_no_sata_irq */
@@ -227,7 +227,7 @@ static const struct ata_port_info sil_port_info[] = {
SIL_FLAG_NO_SATA_IRQ,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x3f, /* udma0-5 */
+ .udma_mask = ATA_UDMA5,
.port_ops = &sil_ops,
},
/* sil_3512 */
@@ -235,7 +235,7 @@ static const struct ata_port_info sil_port_info[] = {
.flags = SIL_DFL_PORT_FLAGS | SIL_FLAG_RERR_ON_DMA_ACT,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x3f, /* udma0-5 */
+ .udma_mask = ATA_UDMA5,
.port_ops = &sil_ops,
},
/* sil_3114 */
@@ -243,7 +243,7 @@ static const struct ata_port_info sil_port_info[] = {
.flags = SIL_DFL_PORT_FLAGS | SIL_FLAG_RERR_ON_DMA_ACT,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x3f, /* udma0-5 */
+ .udma_mask = ATA_UDMA5,
.port_ops = &sil_ops,
},
};
@@ -262,8 +262,9 @@ static const struct {
unsigned long sfis_cfg; /* SATA FIS reception config register */
} sil_port[] = {
/* port 0 ... */
- { 0x80, 0x8A, 0x00, 0x10, 0x40, 0x100, 0x148, 0xb4, 0x14c },
- { 0xC0, 0xCA, 0x08, 0x18, 0x44, 0x180, 0x1c8, 0xf4, 0x1cc },
+ /* tf ctl bmdma bmdma2 fifo scr sien mode sfis */
+ { 0x80, 0x8A, 0x0, 0x10, 0x40, 0x100, 0x148, 0xb4, 0x14c },
+ { 0xC0, 0xCA, 0x8, 0x18, 0x44, 0x180, 0x1c8, 0xf4, 0x1cc },
{ 0x280, 0x28A, 0x200, 0x210, 0x240, 0x300, 0x348, 0x2b4, 0x34c },
{ 0x2C0, 0x2CA, 0x208, 0x218, 0x244, 0x380, 0x3c8, 0x2f4, 0x3cc },
/* ... port 3 */
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index 0ddfae9..ac43a30 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -426,7 +426,7 @@ static const struct ata_port_info sil24_port_info[] = {
SIL24_FLAG_PCIX_IRQ_WOC,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x3f, /* udma0-5 */
+ .udma_mask = ATA_UDMA5, /* udma0-5 */
.port_ops = &sil24_ops,
},
/* sil_3132 */
@@ -434,7 +434,7 @@ static const struct ata_port_info sil24_port_info[] = {
.flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(2),
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x3f, /* udma0-5 */
+ .udma_mask = ATA_UDMA5, /* udma0-5 */
.port_ops = &sil24_ops,
},
/* sil_3131/sil_3531 */
@@ -442,7 +442,7 @@ static const struct ata_port_info sil24_port_info[] = {
.flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(1),
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x3f, /* udma0-5 */
+ .udma_mask = ATA_UDMA5, /* udma0-5 */
.port_ops = &sil24_ops,
},
};
@@ -888,7 +888,7 @@ static irqreturn_t sil24_interrupt(int irq, void *dev_instance)
if (status & (1 << i)) {
struct ata_port *ap = host->ports[i];
if (ap && !(ap->flags & ATA_FLAG_DISABLED)) {
- sil24_host_intr(host->ports[i]);
+ sil24_host_intr(ap);
handled++;
} else
printk(KERN_ERR DRV_NAME
diff --git a/drivers/ata/sata_sis.c b/drivers/ata/sata_sis.c
index f111c98..fd80bcf 100644
--- a/drivers/ata/sata_sis.c
+++ b/drivers/ata/sata_sis.c
@@ -133,7 +133,7 @@ static const struct ata_port_info sis_port_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
.pio_mask = 0x1f,
.mwdma_mask = 0x7,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &sis_ops,
};
diff --git a/drivers/ata/sata_svw.c b/drivers/ata/sata_svw.c
index bcb2cd8..63fe99a 100644
--- a/drivers/ata/sata_svw.c
+++ b/drivers/ata/sata_svw.c
@@ -107,7 +107,7 @@ static u32 k2_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
{
if (sc_reg > SCR_CONTROL)
return 0xffffffffU;
- return readl((void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4));
+ return readl(ap->ioaddr.scr_addr + (sc_reg * 4));
}
@@ -116,7 +116,7 @@ static void k2_sata_scr_write (struct ata_port *ap, unsigned int sc_reg,
{
if (sc_reg > SCR_CONTROL)
return;
- writel(val, (void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4));
+ writel(val, ap->ioaddr.scr_addr + (sc_reg * 4));
}
@@ -197,7 +197,8 @@ static void k2_bmdma_setup_mmio (struct ata_queued_cmd *qc)
struct ata_port *ap = qc->ap;
unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
u8 dmactl;
- void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
+ void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
/* load PRD table addr. */
mb(); /* make sure PRD table writes are visible to controller */
writel(ap->prd_dma, mmio + ATA_DMA_TABLE_OFS);
@@ -225,7 +226,7 @@ static void k2_bmdma_setup_mmio (struct ata_queued_cmd *qc)
static void k2_bmdma_start_mmio (struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
- void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
+ void __iomem *mmio = ap->ioaddr.bmdma_addr;
u8 dmactl;
/* start host DMA transaction */
@@ -253,7 +254,7 @@ static void k2_bmdma_start_mmio (struct ata_queued_cmd *qc)
static u8 k2_stat_check_status(struct ata_port *ap)
{
- return readl((void __iomem *) ap->ioaddr.status_addr);
+ return readl(ap->ioaddr.status_addr);
}
#ifdef CONFIG_PPC_OF
@@ -360,7 +361,7 @@ static const struct ata_port_info k2_port_info[] = {
ATA_FLAG_MMIO | K2_FLAG_NO_ATAPI_DMA,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &k2_sata_ops,
},
/* board_svw8 */
@@ -370,7 +371,7 @@ static const struct ata_port_info k2_port_info[] = {
K2_FLAG_SATA_8_PORTS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &k2_sata_ops,
},
};
diff --git a/drivers/ata/sata_sx4.c b/drivers/ata/sata_sx4.c
index 2d14f3d..5193bd8 100644
--- a/drivers/ata/sata_sx4.c
+++ b/drivers/ata/sata_sx4.c
@@ -30,6 +30,54 @@
*
*/
+/*
+ Theory of operation
+ -------------------
+
+ The SX4 (PDC20621) chip features a single Host DMA (HDMA) copy
+ engine, DIMM memory, and four ATA engines (one per SATA port).
+ Data is copied to/from DIMM memory by the HDMA engine, before
+ handing off to one (or more) of the ATA engines. The ATA
+ engines operate solely on DIMM memory.
+
+ The SX4 behaves like a PATA chip, with no SATA controls or
+ knowledge whatsoever, leading to the presumption that
+ PATA<->SATA bridges exist on SX4 boards, external to the
+ PDC20621 chip itself.
+
+ The chip is quite capable, supporting an XOR engine and linked
+ hardware commands (permits a string to transactions to be
+ submitted and waited-on as a single unit), and an optional
+ microprocessor.
+
+ The limiting factor is largely software. This Linux driver was
+ written to multiplex the single HDMA engine to copy disk
+ transactions into a fixed DIMM memory space, from where an ATA
+ engine takes over. As a result, each WRITE looks like this:
+
+ submit HDMA packet to hardware
+ hardware copies data from system memory to DIMM
+ hardware raises interrupt
+
+ submit ATA packet to hardware
+ hardware executes ATA WRITE command, w/ data in DIMM
+ hardware raises interrupt
+
+ and each READ looks like this:
+
+ submit ATA packet to hardware
+ hardware executes ATA READ command, w/ data in DIMM
+ hardware raises interrupt
+
+ submit HDMA packet to hardware
+ hardware copies data from DIMM to system memory
+ hardware raises interrupt
+
+ This is a very slow, lock-step way of doing things that can
+ certainly be improved by motivated kernel hackers.
+
+ */
+
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
@@ -58,6 +106,8 @@ enum {
PDC_INT_SEQMASK = 0x40, /* Mask of asserted SEQ INTs */
PDC_HDMA_CTLSTAT = 0x12C, /* Host DMA control / status */
+ PDC_CTLSTAT = 0x60, /* IDEn control / status */
+
PDC_20621_SEQCTL = 0x400,
PDC_20621_SEQMASK = 0x480,
PDC_20621_GENERAL_CTL = 0x484,
@@ -87,48 +137,60 @@ enum {
board_20621 = 0, /* FastTrak S150 SX4 */
- PDC_RESET = (1 << 11), /* HDMA reset */
+ PDC_MASK_INT = (1 << 10), /* HDMA/ATA mask int */
+ PDC_RESET = (1 << 11), /* HDMA/ATA reset */
+ PDC_DMA_ENABLE = (1 << 7), /* DMA start/stop */
PDC_MAX_HDMA = 32,
PDC_HDMA_Q_MASK = (PDC_MAX_HDMA - 1),
- PDC_DIMM0_SPD_DEV_ADDRESS = 0x50,
- PDC_DIMM1_SPD_DEV_ADDRESS = 0x51,
- PDC_MAX_DIMM_MODULE = 0x02,
- PDC_I2C_CONTROL_OFFSET = 0x48,
- PDC_I2C_ADDR_DATA_OFFSET = 0x4C,
- PDC_DIMM0_CONTROL_OFFSET = 0x80,
- PDC_DIMM1_CONTROL_OFFSET = 0x84,
- PDC_SDRAM_CONTROL_OFFSET = 0x88,
- PDC_I2C_WRITE = 0x00000000,
- PDC_I2C_READ = 0x00000040,
- PDC_I2C_START = 0x00000080,
- PDC_I2C_MASK_INT = 0x00000020,
- PDC_I2C_COMPLETE = 0x00010000,
- PDC_I2C_NO_ACK = 0x00100000,
- PDC_DIMM_SPD_SUBADDRESS_START = 0x00,
- PDC_DIMM_SPD_SUBADDRESS_END = 0x7F,
- PDC_DIMM_SPD_ROW_NUM = 3,
- PDC_DIMM_SPD_COLUMN_NUM = 4,
- PDC_DIMM_SPD_MODULE_ROW = 5,
- PDC_DIMM_SPD_TYPE = 11,
- PDC_DIMM_SPD_FRESH_RATE = 12,
- PDC_DIMM_SPD_BANK_NUM = 17,
- PDC_DIMM_SPD_CAS_LATENCY = 18,
- PDC_DIMM_SPD_ATTRIBUTE = 21,
- PDC_DIMM_SPD_ROW_PRE_CHARGE = 27,
- PDC_DIMM_SPD_ROW_ACTIVE_DELAY = 28,
- PDC_DIMM_SPD_RAS_CAS_DELAY = 29,
- PDC_DIMM_SPD_ACTIVE_PRECHARGE = 30,
- PDC_DIMM_SPD_SYSTEM_FREQ = 126,
- PDC_CTL_STATUS = 0x08,
- PDC_DIMM_WINDOW_CTLR = 0x0C,
- PDC_TIME_CONTROL = 0x3C,
- PDC_TIME_PERIOD = 0x40,
- PDC_TIME_COUNTER = 0x44,
- PDC_GENERAL_CTLR = 0x484,
- PCI_PLL_INIT = 0x8A531824,
- PCI_X_TCOUNT = 0xEE1E5CFF
+ PDC_DIMM0_SPD_DEV_ADDRESS = 0x50,
+ PDC_DIMM1_SPD_DEV_ADDRESS = 0x51,
+ PDC_I2C_CONTROL = 0x48,
+ PDC_I2C_ADDR_DATA = 0x4C,
+ PDC_DIMM0_CONTROL = 0x80,
+ PDC_DIMM1_CONTROL = 0x84,
+ PDC_SDRAM_CONTROL = 0x88,
+ PDC_I2C_WRITE = 0, /* master -> slave */
+ PDC_I2C_READ = (1 << 6), /* master <- slave */
+ PDC_I2C_START = (1 << 7), /* start I2C proto */
+ PDC_I2C_MASK_INT = (1 << 5), /* mask I2C interrupt */
+ PDC_I2C_COMPLETE = (1 << 16), /* I2C normal compl. */
+ PDC_I2C_NO_ACK = (1 << 20), /* slave no-ack addr */
+ PDC_DIMM_SPD_SUBADDRESS_START = 0x00,
+ PDC_DIMM_SPD_SUBADDRESS_END = 0x7F,
+ PDC_DIMM_SPD_ROW_NUM = 3,
+ PDC_DIMM_SPD_COLUMN_NUM = 4,
+ PDC_DIMM_SPD_MODULE_ROW = 5,
+ PDC_DIMM_SPD_TYPE = 11,
+ PDC_DIMM_SPD_FRESH_RATE = 12,
+ PDC_DIMM_SPD_BANK_NUM = 17,
+ PDC_DIMM_SPD_CAS_LATENCY = 18,
+ PDC_DIMM_SPD_ATTRIBUTE = 21,
+ PDC_DIMM_SPD_ROW_PRE_CHARGE = 27,
+ PDC_DIMM_SPD_ROW_ACTIVE_DELAY = 28,
+ PDC_DIMM_SPD_RAS_CAS_DELAY = 29,
+ PDC_DIMM_SPD_ACTIVE_PRECHARGE = 30,
+ PDC_DIMM_SPD_SYSTEM_FREQ = 126,
+ PDC_CTL_STATUS = 0x08,
+ PDC_DIMM_WINDOW_CTLR = 0x0C,
+ PDC_TIME_CONTROL = 0x3C,
+ PDC_TIME_PERIOD = 0x40,
+ PDC_TIME_COUNTER = 0x44,
+ PDC_GENERAL_CTLR = 0x484,
+ PCI_PLL_INIT = 0x8A531824,
+ PCI_X_TCOUNT = 0xEE1E5CFF,
+
+ /* PDC_TIME_CONTROL bits */
+ PDC_TIMER_BUZZER = (1 << 10),
+ PDC_TIMER_MODE_PERIODIC = 0, /* bits 9:8 == 00 */
+ PDC_TIMER_MODE_ONCE = (1 << 8), /* bits 9:8 == 01 */
+ PDC_TIMER_ENABLE = (1 << 7),
+ PDC_TIMER_MASK_INT = (1 << 5),
+ PDC_TIMER_SEQ_MASK = 0x1f, /* SEQ ID for timer */
+ PDC_TIMER_DEFAULT = PDC_TIMER_MODE_ONCE |
+ PDC_TIMER_ENABLE |
+ PDC_TIMER_MASK_INT,
};
@@ -217,7 +279,7 @@ static const struct ata_port_info pdc_port_info[] = {
ATA_FLAG_NO_ATAPI | ATA_FLAG_PIO_POLLING,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
+ .udma_mask = ATA_UDMA6,
.port_ops = &pdc_20621_ops,
},
@@ -999,17 +1061,17 @@ static unsigned int pdc20621_i2c_read(struct ata_host *host, u32 device,
i2creg |= subaddr << 16;
/* Set the device and subaddress */
- writel(i2creg, mmio + PDC_I2C_ADDR_DATA_OFFSET);
- readl(mmio + PDC_I2C_ADDR_DATA_OFFSET);
+ writel(i2creg, mmio + PDC_I2C_ADDR_DATA);
+ readl(mmio + PDC_I2C_ADDR_DATA);
/* Write Control to perform read operation, mask int */
writel(PDC_I2C_READ | PDC_I2C_START | PDC_I2C_MASK_INT,
- mmio + PDC_I2C_CONTROL_OFFSET);
+ mmio + PDC_I2C_CONTROL);
for (count = 0; count <= 1000; count ++) {
- status = readl(mmio + PDC_I2C_CONTROL_OFFSET);
+ status = readl(mmio + PDC_I2C_CONTROL);
if (status & PDC_I2C_COMPLETE) {
- status = readl(mmio + PDC_I2C_ADDR_DATA_OFFSET);
+ status = readl(mmio + PDC_I2C_ADDR_DATA);
break;
} else if (count == 1000)
return 0;
@@ -1099,8 +1161,8 @@ static int pdc20621_prog_dimm0(struct ata_host *host)
data |= (((size / 16) - 1) << 16);
data |= (0 << 23);
data |= 8;
- writel(data, mmio + PDC_DIMM0_CONTROL_OFFSET);
- readl(mmio + PDC_DIMM0_CONTROL_OFFSET);
+ writel(data, mmio + PDC_DIMM0_CONTROL);
+ readl(mmio + PDC_DIMM0_CONTROL);
return size;
}
@@ -1122,27 +1184,27 @@ static unsigned int pdc20621_prog_dimm_global(struct ata_host *host)
*/
data = 0x022259F1;
- writel(data, mmio + PDC_SDRAM_CONTROL_OFFSET);
- readl(mmio + PDC_SDRAM_CONTROL_OFFSET);
+ writel(data, mmio + PDC_SDRAM_CONTROL);
+ readl(mmio + PDC_SDRAM_CONTROL);
/* Turn on for ECC */
pdc20621_i2c_read(host, PDC_DIMM0_SPD_DEV_ADDRESS,
PDC_DIMM_SPD_TYPE, &spd0);
if (spd0 == 0x02) {
data |= (0x01 << 16);
- writel(data, mmio + PDC_SDRAM_CONTROL_OFFSET);
- readl(mmio + PDC_SDRAM_CONTROL_OFFSET);
+ writel(data, mmio + PDC_SDRAM_CONTROL);
+ readl(mmio + PDC_SDRAM_CONTROL);
printk(KERN_ERR "Local DIMM ECC Enabled\n");
}
/* DIMM Initialization Select/Enable (bit 18/19) */
data &= (~(1<<18));
data |= (1<<19);
- writel(data, mmio + PDC_SDRAM_CONTROL_OFFSET);
+ writel(data, mmio + PDC_SDRAM_CONTROL);
error = 1;
for (i = 1; i <= 10; i++) { /* polling ~5 secs */
- data = readl(mmio + PDC_SDRAM_CONTROL_OFFSET);
+ data = readl(mmio + PDC_SDRAM_CONTROL);
if (!(data & (1<<19))) {
error = 0;
break;
@@ -1176,7 +1238,7 @@ static unsigned int pdc20621_dimm_init(struct ata_host *host)
VPRINTK("Time Period Register (0x40): 0x%x\n", time_period);
/* Enable timer */
- writel(0x00001a0, mmio + PDC_TIME_CONTROL);
+ writel(PDC_TIMER_DEFAULT, mmio + PDC_TIME_CONTROL);
readl(mmio + PDC_TIME_CONTROL);
/* Wait 3 seconds */
diff --git a/drivers/ata/sata_uli.c b/drivers/ata/sata_uli.c
index 6815de7..aca7181 100644
--- a/drivers/ata/sata_uli.c
+++ b/drivers/ata/sata_uli.c
@@ -129,7 +129,7 @@ static const struct ata_port_info uli_port_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_IGN_SIMPLEX,
.pio_mask = 0x1f, /* pio0-4 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &uli_ops,
};
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index e8b90e7..a4c0832 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -223,7 +223,7 @@ static const struct ata_port_info vt6420_port_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &vt6420_sata_ops,
};
@@ -231,7 +231,7 @@ static struct ata_port_info vt6421_sport_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &vt6421_sata_ops,
};
@@ -239,7 +239,7 @@ static struct ata_port_info vt6421_pport_info = {
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_NO_LEGACY,
.pio_mask = 0x1f,
.mwdma_mask = 0,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &vt6421_pata_ops,
};
@@ -303,9 +303,7 @@ static int vt6420_prereset(struct ata_port *ap, unsigned long deadline)
if (!(ap->pflags & ATA_PFLAG_LOADING))
goto skip_scr;
- /* Resume phy. This is the old resume sequence from
- * __sata_phy_reset().
- */
+ /* Resume phy. This is the old SATA resume sequence */
svia_scr_write(ap, SCR_CONTROL, 0x300);
svia_scr_read(ap, SCR_CONTROL); /* flush */
diff --git a/drivers/ata/sata_vsc.c b/drivers/ata/sata_vsc.c
index 8133017..1b5d81f 100644
--- a/drivers/ata/sata_vsc.c
+++ b/drivers/ata/sata_vsc.c
@@ -371,7 +371,7 @@ static int __devinit vsc_sata_init_one (struct pci_dev *pdev, const struct pci_d
ATA_FLAG_MMIO,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &vsc_sata_ops,
};
const struct ata_port_info *ppi[] = { &pi, NULL };
diff --git a/include/linux/ata.h b/include/linux/ata.h
index 703febb..407dc7e 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -126,6 +126,7 @@ enum {
ATA_REG_IRQ = ATA_REG_NSECT,
/* ATA device commands */
+ ATA_CMD_DEV_RESET = 0x08, /* ATAPI device reset */
ATA_CMD_CHK_POWER = 0xE5, /* check power mode */
ATA_CMD_STANDBY = 0xE2, /* place in standby power mode */
ATA_CMD_IDLE = 0xE3, /* place in idle power mode */
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 620da7b..a3df646 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -116,6 +116,7 @@ static inline struct device *pci_dev_to_dev(struct pci_dev *pdev)
enum {
/* various global constants */
LIBATA_MAX_PRD = ATA_MAX_PRD / 2,
+ LIBATA_DUMB_MAX_PRD = ATA_MAX_PRD / 4, /* Worst case */
ATA_MAX_PORTS = 8,
ATA_DEF_QUEUE = 1,
/* tag ATA_MAX_QUEUE - 1 is reserved for internal commands */
@@ -136,6 +137,8 @@ enum {
ATA_DFLAG_CDB_INTR = (1 << 2), /* device asserts INTRQ when ready for CDB */
ATA_DFLAG_NCQ = (1 << 3), /* device supports NCQ */
ATA_DFLAG_FLUSH_EXT = (1 << 4), /* do FLUSH_EXT instead of FLUSH */
+ ATA_DFLAG_ACPI_PENDING = (1 << 5), /* ACPI resume action pending */
+ ATA_DFLAG_ACPI_FAILED = (1 << 6), /* ACPI on devcfg has failed */
ATA_DFLAG_CFG_MASK = (1 << 8) - 1,
ATA_DFLAG_PIO = (1 << 8), /* device limited to PIO mode */
@@ -196,6 +199,7 @@ enum {
ATA_PFLAG_FLUSH_PORT_TASK = (1 << 16), /* flush port task */
ATA_PFLAG_SUSPENDED = (1 << 17), /* port is suspended (power) */
ATA_PFLAG_PM_PENDING = (1 << 18), /* PM operation pending */
+ ATA_PFLAG_GTM_VALID = (1 << 19), /* acpi_gtm data valid */
/* struct ata_queued_cmd flags */
ATA_QCFLAG_ACTIVE = (1 << 0), /* cmd not yet ack'd to scsi lyer */
@@ -363,6 +367,9 @@ struct ata_host {
void *private_data;
const struct ata_port_operations *ops;
unsigned long flags;
+#ifdef CONFIG_ATA_ACPI
+ acpi_handle acpi_handle;
+#endif
struct ata_port *simplex_claimed; /* channel owning the DMA */
struct ata_port *ports[0];
};
@@ -429,6 +436,9 @@ struct ata_device {
unsigned int devno; /* 0 or 1 */
unsigned long flags; /* ATA_DFLAG_xxx */
struct scsi_device *sdev; /* attached SCSI device */
+#ifdef CONFIG_ATA_ACPI
+ acpi_handle acpi_handle;
+#endif
/* n_sector is used as CLEAR_OFFSET, read comment above CLEAR_OFFSET */
u64 n_sectors; /* size of device, if ATA */
unsigned int class; /* ATA_DEV_xxx */
@@ -457,10 +467,6 @@ struct ata_device {
struct ata_ering ering;
int spdn_cnt;
unsigned int horkage; /* List of broken features */
-#ifdef CONFIG_ATA_ACPI
- /* ACPI objects info */
- acpi_handle obj_handle;
-#endif
};
/* Offset into struct ata_device. Fields above it are maintained
@@ -489,6 +495,17 @@ struct ata_eh_context {
unsigned int did_probe_mask;
};
+struct ata_acpi_drive
+{
+ u32 pio;
+ u32 dma;
+} __packed;
+
+struct ata_acpi_gtm {
+ struct ata_acpi_drive drive[2];
+ u32 flags;
+} __packed;
+
struct ata_port {
struct Scsi_Host *scsi_host; /* our co-allocated scsi host */
const struct ata_port_operations *ops;
@@ -549,6 +566,10 @@ struct ata_port {
void *private_data;
+#ifdef CONFIG_ATA_ACPI
+ acpi_handle acpi_handle;
+ struct ata_acpi_gtm acpi_gtm;
+#endif
u8 sector_buf[ATA_SECT_SIZE]; /* owned by EH */
};
@@ -758,6 +779,7 @@ extern void ata_data_xfer(struct ata_device *adev, unsigned char *buf,
unsigned int buflen, int write_data);
extern void ata_data_xfer_noirq(struct ata_device *adev, unsigned char *buf,
unsigned int buflen, int write_data);
+extern void ata_dumb_qc_prep(struct ata_queued_cmd *qc);
extern void ata_qc_prep(struct ata_queued_cmd *qc);
extern void ata_noop_qc_prep(struct ata_queued_cmd *qc);
extern unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc);
diff --git a/include/linux/pata_platform.h b/include/linux/pata_platform.h
index 2d5fd64..5799e8d 100644
--- a/include/linux/pata_platform.h
+++ b/include/linux/pata_platform.h
@@ -8,6 +8,11 @@ struct pata_platform_info {
* spacing used by ata_std_ports().
*/
unsigned int ioport_shift;
+ /*
+ * Indicate platform specific irq types and initial
+ * IRQ flags when call request_irq()
+ */
+ unsigned int irq_flags;
};
#endif /* __LINUX_PATA_PLATFORM_H */
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2007-05-11 22:32 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2007-05-11 22:32 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
Documentation/feature-removal-schedule.txt | 19 ++
drivers/ata/Kconfig | 36 ++---
drivers/ata/Makefile | 2 +-
drivers/ata/ahci.c | 5 +-
drivers/ata/ata_generic.c | 12 +-
drivers/ata/ata_piix.c | 8 +-
drivers/ata/libata-acpi.c | 192 +++++++++++-----------
drivers/ata/libata-core.c | 72 ++++----
drivers/ata/libata-eh.c | 246 +---------------------------
drivers/ata/libata-scsi.c | 157 ++++--------------
drivers/ata/libata-sff.c | 162 ++++++++++---------
drivers/ata/libata.h | 7 +-
drivers/ata/pata_ali.c | 36 ++---
drivers/ata/pata_amd.c | 13 +-
drivers/ata/pata_artop.c | 25 ++--
drivers/ata/pata_atiixp.c | 10 +-
drivers/ata/pata_cmd640.c | 11 +-
drivers/ata/pata_cmd64x.c | 17 +--
drivers/ata/pata_cs5520.c | 4 -
drivers/ata/pata_cs5530.c | 14 +-
drivers/ata/pata_cs5535.c | 10 +-
drivers/ata/pata_cypress.c | 10 +-
drivers/ata/pata_efar.c | 10 +-
drivers/ata/pata_hpt366.c | 17 +-
drivers/ata/pata_hpt37x.c | 33 ++--
drivers/ata/pata_hpt3x2n.c | 13 +-
drivers/ata/pata_hpt3x3.c | 10 +-
drivers/ata/pata_it8213.c | 12 +-
drivers/ata/pata_it821x.c | 16 +-
drivers/ata/pata_ixp4xx_cf.c | 2 +-
drivers/ata/pata_jmicron.c | 10 +-
drivers/ata/pata_marvell.c | 15 +-
drivers/ata/pata_mpc52xx.c | 4 -
drivers/ata/pata_mpiix.c | 4 -
drivers/ata/pata_netcell.c | 10 +-
drivers/ata/pata_ns87410.c | 10 +-
drivers/ata/pata_oldpiix.c | 10 +-
drivers/ata/pata_opti.c | 10 +-
drivers/ata/pata_optidma.c | 16 +--
drivers/ata/pata_pcmcia.c | 1 +
drivers/ata/pata_pdc202xx_old.c | 12 +-
drivers/ata/pata_platform.c | 4 +-
drivers/ata/pata_radisys.c | 10 +-
drivers/ata/pata_rz1000.c | 18 +--
drivers/ata/pata_sc1200.c | 12 +-
drivers/ata/pata_scc.c | 4 -
drivers/ata/pata_serverworks.c | 19 +--
drivers/ata/pata_sil680.c | 14 +-
drivers/ata/pata_sis.c | 33 ++--
drivers/ata/pata_sl82c105.c | 17 +-
drivers/ata/pata_triflex.c | 10 +-
drivers/ata/pata_via.c | 36 ++---
drivers/ata/sata_inic162x.c | 4 -
drivers/ata/sata_nv.c | 16 +--
drivers/ata/sata_sil.c | 4 -
drivers/ata/sata_sil24.c | 4 -
drivers/ata/sata_sis.c | 6 +-
drivers/ata/sata_uli.c | 22 ++-
drivers/ata/sata_via.c | 6 +-
drivers/ata/sis.h | 2 +-
drivers/pci/quirks.c | 1 +
include/linux/libata.h | 31 +---
include/linux/pci_ids.h | 1 +
63 files changed, 532 insertions(+), 1025 deletions(-)
Aeschbacher, Fabrice (1):
pata_pcmcia: recognize 2GB CompactFlash from Transcend
Andrew Morton (1):
git-libata-all: sata_via build fix
Henry Su (2):
Add the combined mode for ATI SB700
add the ATI SB700 SATA controller device id to AHCI pci table
Jan Engelhardt (1):
Use menuconfig objects: libata
Olof Johansson (1):
pata_platform: don't use generic ata_port_start
Tejun Heo (8):
libata: reimplement suspend/resume support using sdev->manage_start_stop
libata: implement libata.spindown_compat
libata: clean up SFF init mess
libata: ignore EH scheduling during initialization
libata: fallback to the other IDENTIFY on device error, take#2
libata: give devices one last chance even if recovery failed with -EINVAL
libata-acpi: s/CONFIG_SATA_ACPI/CONFIG_ATA_ACPI/
libata-acpi: clean up parameters and misc stuff
diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt
index c6322c7..498ff31 100644
--- a/Documentation/feature-removal-schedule.txt
+++ b/Documentation/feature-removal-schedule.txt
@@ -328,3 +328,22 @@ Who: Adrian Bunk <bunk@stusta.de>
---------------------------
+What: libata.spindown_compat module parameter
+When: Dec 2008
+Why: halt(8) synchronizes caches for and spins down libata disks
+ because libata didn't use to spin down disk on system halt
+ (only synchronized caches).
+ Spin down on system halt is now implemented and can be tested
+ using sysfs node /sys/class/scsi_disk/h:c:i:l/manage_start_stop.
+ Because issuing spin down command to an already spun down disk
+ makes some disks spin up just to spin down again, the old
+ behavior needs to be maintained till userspace tool is updated
+ to check the sysfs node and not to spin down disks with the
+ node set to one.
+ This module parameter is to give userspace tool the time to
+ get updated and should be removed after userspace is
+ reasonably updated.
+Who: Tejun Heo <htejun@gmail.com>
+
+---------------------------
+
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index f031b87..ad1f59c 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -2,11 +2,9 @@
# SATA/PATA driver configuration
#
-menu "Serial ATA (prod) and Parallel ATA (experimental) drivers"
+menuconfig ATA
+ tristate "Serial ATA (prod) and Parallel ATA (experimental) drivers"
depends on HAS_IOMEM
-
-config ATA
- tristate "ATA device support"
depends on BLOCK
depends on !(M32R || M68K) || BROKEN
depends on !SUN4 || BROKEN
@@ -24,6 +22,19 @@ config ATA_NONSTANDARD
bool
default n
+config ATA_ACPI
+ bool
+ depends on ACPI && PCI
+ default y
+ help
+ This option adds support for ATA-related ACPI objects.
+ These ACPI objects add the ability to retrieve taskfiles
+ from the ACPI BIOS and write them to the disk controller.
+ These objects may be related to performance, security,
+ power management, or other areas.
+ You can disable this at kernel boot time by using the
+ option libata.noacpi=1
+
config SATA_AHCI
tristate "AHCI SATA support"
depends on PCI
@@ -157,19 +168,6 @@ config SATA_INIC162X
help
This option enables support for Initio 162x Serial ATA.
-config SATA_ACPI
- bool
- depends on ACPI && PCI
- default y
- help
- This option adds support for SATA-related ACPI objects.
- These ACPI objects add the ability to retrieve taskfiles
- from the ACPI BIOS and write them to the disk controller.
- These objects may be related to performance, security,
- power management, or other areas.
- You can disable this at kernel boot time by using the
- option libata.noacpi=1
-
config PATA_ALI
tristate "ALi PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
@@ -585,6 +583,4 @@ config PATA_SCC
If unsure, say N.
-endif
-endmenu
-
+endif # ATA
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 6f42a0e..8149c68 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -69,4 +69,4 @@ obj-$(CONFIG_ATA_GENERIC) += ata_generic.o
obj-$(CONFIG_PATA_LEGACY) += pata_legacy.o
libata-objs := libata-core.o libata-scsi.o libata-sff.o libata-eh.o
-libata-$(CONFIG_SATA_ACPI) += libata-acpi.o
+libata-$(CONFIG_ATA_ACPI) += libata-acpi.o
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index d961789..1ae443d 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -250,10 +250,6 @@ static struct scsi_host_template ahci_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .suspend = ata_scsi_device_suspend,
- .resume = ata_scsi_device_resume,
-#endif
};
static const struct ata_port_operations ahci_ops = {
@@ -400,6 +396,7 @@ static const struct pci_device_id ahci_pci_tbl[] = {
/* ATI */
{ PCI_VDEVICE(ATI, 0x4380), board_ahci_sb600 }, /* ATI SB600 */
+ { PCI_VDEVICE(ATI, 0x4390), board_ahci_sb600 }, /* ATI SB700 */
/* VIA */
{ PCI_VDEVICE(VIA, 0x3349), board_ahci_vt8251 }, /* VIA VT8251 */
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
index 92a491d..c3d7532 100644
--- a/drivers/ata/ata_generic.c
+++ b/drivers/ata/ata_generic.c
@@ -54,7 +54,7 @@ static int generic_set_mode(struct ata_port *ap, struct ata_device **unused)
for (i = 0; i < ATA_MAX_DEVICES; i++) {
struct ata_device *dev = &ap->device[i];
- if (ata_dev_ready(dev)) {
+ if (ata_dev_enabled(dev)) {
/* We don't really care */
dev->pio_mode = XFER_PIO_0;
dev->dma_mode = XFER_MW_DMA_0;
@@ -90,10 +90,6 @@ static struct scsi_host_template generic_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations generic_port_ops = {
@@ -145,7 +141,7 @@ static int all_generic_ide; /* Set to claim all devices */
static int ata_generic_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
u16 command;
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &generic_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -153,7 +149,7 @@ static int ata_generic_init_one(struct pci_dev *dev, const struct pci_device_id
.udma_mask = 0x3f,
.port_ops = &generic_port_ops
};
- static struct ata_port_info *port_info[2] = { &info, &info };
+ const struct ata_port_info *ppi[] = { &info, NULL };
/* Don't use the generic entry unless instructed to do so */
if (id->driver_data == 1 && all_generic_ide == 0)
@@ -179,7 +175,7 @@ static int ata_generic_init_one(struct pci_dev *dev, const struct pci_device_id
if (dev->vendor == PCI_VENDOR_ID_AL)
ata_pci_clear_simplex(dev);
- return ata_pci_init_one(dev, port_info, 2);
+ return ata_pci_init_one(dev, ppi);
}
static struct pci_device_id ata_generic[] = {
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 4a795fd..13b6b1d 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -275,10 +275,6 @@ static struct scsi_host_template piix_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static const struct ata_port_operations piix_pata_ops = {
@@ -1034,7 +1030,7 @@ static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
static int printed_version;
struct device *dev = &pdev->dev;
struct ata_port_info port_info[2];
- struct ata_port_info *ppinfo[2] = { &port_info[0], &port_info[1] };
+ const struct ata_port_info *ppi[] = { &port_info[0], &port_info[1] };
struct piix_host_priv *hpriv;
unsigned long port_flags;
@@ -1093,7 +1089,7 @@ static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
port_info[1].mwdma_mask = 0;
port_info[1].udma_mask = 0;
}
- return ata_pci_init_one(pdev, ppinfo, 2);
+ return ata_pci_init_one(pdev, ppi);
}
static int __init piix_init(void)
diff --git a/drivers/ata/libata-acpi.c b/drivers/ata/libata-acpi.c
index cb3eab6..ed4138e 100644
--- a/drivers/ata/libata-acpi.c
+++ b/drivers/ata/libata-acpi.c
@@ -270,8 +270,7 @@ out:
/**
* do_drive_get_GTF - get the drive bootup default taskfile settings
- * @ap: the ata_port for the drive
- * @ix: target ata_device (drive) index
+ * @dev: target ATA device
* @gtf_length: number of bytes of _GTF data returned at @gtf_address
* @gtf_address: buffer containing _GTF taskfile arrays
*
@@ -286,20 +285,19 @@ out:
* The returned @gtf_length and @gtf_address are only valid if the
* function return value is 0.
*/
-static int do_drive_get_GTF(struct ata_port *ap, int ix,
- unsigned int *gtf_length, unsigned long *gtf_address,
- unsigned long *obj_loc)
+static int do_drive_get_GTF(struct ata_device *dev, unsigned int *gtf_length,
+ unsigned long *gtf_address, unsigned long *obj_loc)
{
- acpi_status status;
- acpi_handle dev_handle = NULL;
- acpi_handle chan_handle, drive_handle;
- acpi_integer pcidevfn = 0;
- u32 dev_adr;
- struct acpi_buffer output;
- union acpi_object *out_obj;
- struct device *dev = ap->host->dev;
- struct ata_device *atadev = &ap->device[ix];
- int err = -ENODEV;
+ struct ata_port *ap = dev->ap;
+ acpi_status status;
+ acpi_handle dev_handle = NULL;
+ acpi_handle chan_handle, drive_handle;
+ acpi_integer pcidevfn = 0;
+ u32 dev_adr;
+ struct acpi_buffer output;
+ union acpi_object *out_obj;
+ struct device *gdev = ap->host->dev;
+ int err = -ENODEV;
*gtf_length = 0;
*gtf_address = 0UL;
@@ -309,14 +307,14 @@ static int do_drive_get_GTF(struct ata_port *ap, int ix,
return 0;
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG, "%s: ENTER: port#: %d\n",
+ ata_dev_printk(dev, KERN_DEBUG, "%s: ENTER: port#: %d\n",
__FUNCTION__, ap->port_no);
- if (!ata_dev_enabled(atadev) || (ap->flags & ATA_FLAG_DISABLED)) {
+ if (!ata_dev_enabled(dev) || (ap->flags & ATA_FLAG_DISABLED)) {
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG, "%s: ERR: "
+ ata_dev_printk(dev, KERN_DEBUG, "%s: ERR: "
"ata_dev_present: %d, PORT_DISABLED: %lu\n",
- __FUNCTION__, ata_dev_enabled(atadev),
+ __FUNCTION__, ata_dev_enabled(dev),
ap->flags & ATA_FLAG_DISABLED);
goto out;
}
@@ -324,19 +322,19 @@ static int do_drive_get_GTF(struct ata_port *ap, int ix,
/* Don't continue if device has no _ADR method.
* _GTF is intended for known motherboard devices. */
if (!(ap->cbl == ATA_CBL_SATA)) {
- err = pata_get_dev_handle(dev, &dev_handle, &pcidevfn);
+ err = pata_get_dev_handle(gdev, &dev_handle, &pcidevfn);
if (err < 0) {
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG,
+ ata_dev_printk(dev, KERN_DEBUG,
"%s: pata_get_dev_handle failed (%d)\n",
__FUNCTION__, err);
goto out;
}
} else {
- err = sata_get_dev_handle(dev, &dev_handle, &pcidevfn);
+ err = sata_get_dev_handle(gdev, &dev_handle, &pcidevfn);
if (err < 0) {
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG,
+ ata_dev_printk(dev, KERN_DEBUG,
"%s: sata_get_dev_handle failed (%d\n",
__FUNCTION__, err);
goto out;
@@ -344,7 +342,7 @@ static int do_drive_get_GTF(struct ata_port *ap, int ix,
}
/* Get this drive's _ADR info. if not already known. */
- if (!atadev->obj_handle) {
+ if (!dev->obj_handle) {
if (!(ap->cbl == ATA_CBL_SATA)) {
/* get child objects of dev_handle == channel objects,
* + _their_ children == drive objects */
@@ -352,7 +350,7 @@ static int do_drive_get_GTF(struct ata_port *ap, int ix,
chan_handle = acpi_get_child(dev_handle,
ap->port_no);
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG,
+ ata_dev_printk(dev, KERN_DEBUG,
"%s: chan adr=%d: chan_handle=0x%p\n",
__FUNCTION__, ap->port_no,
chan_handle);
@@ -361,26 +359,26 @@ static int do_drive_get_GTF(struct ata_port *ap, int ix,
goto out;
}
/* TBD: could also check ACPI object VALID bits */
- drive_handle = acpi_get_child(chan_handle, ix);
+ drive_handle = acpi_get_child(chan_handle, dev->devno);
if (!drive_handle) {
err = -ENODEV;
goto out;
}
- dev_adr = ix;
- atadev->obj_handle = drive_handle;
+ dev_adr = dev->devno;
+ dev->obj_handle = drive_handle;
} else { /* for SATA mode */
dev_adr = SATA_ADR_RSVD;
- err = get_sata_adr(dev, dev_handle, pcidevfn, 0,
- ap, atadev, &dev_adr);
+ err = get_sata_adr(gdev, dev_handle, pcidevfn, 0,
+ ap, dev, &dev_adr);
}
if (err < 0 || dev_adr == SATA_ADR_RSVD ||
- !atadev->obj_handle) {
+ !dev->obj_handle) {
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG,
+ ata_dev_printk(dev, KERN_DEBUG,
"%s: get_sata/pata_adr failed: "
"err=%d, dev_adr=%u, obj_handle=0x%p\n",
__FUNCTION__, err, dev_adr,
- atadev->obj_handle);
+ dev->obj_handle);
goto out;
}
}
@@ -391,11 +389,11 @@ static int do_drive_get_GTF(struct ata_port *ap, int ix,
/* _GTF has no input parameters */
err = -EIO;
- status = acpi_evaluate_object(atadev->obj_handle, "_GTF",
+ status = acpi_evaluate_object(dev->obj_handle, "_GTF",
NULL, &output);
if (ACPI_FAILURE(status)) {
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG,
+ ata_dev_printk(dev, KERN_DEBUG,
"%s: Run _GTF error: status = 0x%x\n",
__FUNCTION__, status);
goto out;
@@ -403,7 +401,7 @@ static int do_drive_get_GTF(struct ata_port *ap, int ix,
if (!output.length || !output.pointer) {
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG, "%s: Run _GTF: "
+ ata_dev_printk(dev, KERN_DEBUG, "%s: Run _GTF: "
"length or ptr is NULL (0x%llx, 0x%p)\n",
__FUNCTION__,
(unsigned long long)output.length,
@@ -416,7 +414,7 @@ static int do_drive_get_GTF(struct ata_port *ap, int ix,
if (out_obj->type != ACPI_TYPE_BUFFER) {
kfree(output.pointer);
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG, "%s: Run _GTF: "
+ ata_dev_printk(dev, KERN_DEBUG, "%s: Run _GTF: "
"error: expected object type of "
" ACPI_TYPE_BUFFER, got 0x%x\n",
__FUNCTION__, out_obj->type);
@@ -427,7 +425,7 @@ static int do_drive_get_GTF(struct ata_port *ap, int ix,
if (!out_obj->buffer.length || !out_obj->buffer.pointer ||
out_obj->buffer.length % REGS_PER_GTF) {
if (ata_msg_drv(ap))
- ata_dev_printk(atadev, KERN_ERR,
+ ata_dev_printk(dev, KERN_ERR,
"%s: unexpected GTF length (%d) or addr (0x%p)\n",
__FUNCTION__, out_obj->buffer.length,
out_obj->buffer.pointer);
@@ -439,7 +437,7 @@ static int do_drive_get_GTF(struct ata_port *ap, int ix,
*gtf_address = (unsigned long)out_obj->buffer.pointer;
*obj_loc = (unsigned long)out_obj;
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG, "%s: returning "
+ ata_dev_printk(dev, KERN_DEBUG, "%s: returning "
"gtf_length=%d, gtf_address=0x%lx, obj_loc=0x%lx\n",
__FUNCTION__, *gtf_length, *gtf_address, *obj_loc);
err = 0;
@@ -449,7 +447,7 @@ out:
/**
* taskfile_load_raw - send taskfile registers to host controller
- * @ap: Port to which output is sent
+ * @dev: target ATA device
* @gtf: raw ATA taskfile register set (0x1f1 - 0x1f7)
*
* Outputs ATA taskfile to standard ATA host controller using MMIO
@@ -466,15 +464,15 @@ out:
* LOCKING: TBD:
* Inherited from caller.
*/
-static void taskfile_load_raw(struct ata_port *ap,
- struct ata_device *atadev,
- const struct taskfile_array *gtf)
+static void taskfile_load_raw(struct ata_device *dev,
+ const struct taskfile_array *gtf)
{
+ struct ata_port *ap = dev->ap;
struct ata_taskfile tf;
unsigned int err;
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG, "%s: (0x1f1-1f7): hex: "
+ ata_dev_printk(dev, KERN_DEBUG, "%s: (0x1f1-1f7): hex: "
"%02x %02x %02x %02x %02x %02x %02x\n",
__FUNCTION__,
gtf->tfa[0], gtf->tfa[1], gtf->tfa[2],
@@ -485,7 +483,7 @@ static void taskfile_load_raw(struct ata_port *ap,
&& (gtf->tfa[6] == 0))
return;
- ata_tf_init(atadev, &tf);
+ ata_tf_init(dev, &tf);
/* convert gtf to tf */
tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; /* TBD */
@@ -498,17 +496,16 @@ static void taskfile_load_raw(struct ata_port *ap,
tf.device = gtf->tfa[5]; /* 0x1f6 */
tf.command = gtf->tfa[6]; /* 0x1f7 */
- err = ata_exec_internal(atadev, &tf, NULL, DMA_NONE, NULL, 0);
+ err = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0);
if (err && ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_ERR,
+ ata_dev_printk(dev, KERN_ERR,
"%s: ata_exec_internal failed: %u\n",
__FUNCTION__, err);
}
/**
* do_drive_set_taskfiles - write the drive taskfile settings from _GTF
- * @ap: the ata_port for the drive
- * @atadev: target ata_device
+ * @dev: target ATA device
* @gtf_length: total number of bytes of _GTF taskfiles
* @gtf_address: location of _GTF taskfile arrays
*
@@ -517,30 +514,31 @@ static void taskfile_load_raw(struct ata_port *ap,
* Write {gtf_address, length gtf_length} in groups of
* REGS_PER_GTF bytes.
*/
-static int do_drive_set_taskfiles(struct ata_port *ap,
- struct ata_device *atadev, unsigned int gtf_length,
- unsigned long gtf_address)
+static int do_drive_set_taskfiles(struct ata_device *dev,
+ unsigned int gtf_length,
+ unsigned long gtf_address)
{
- int err = -ENODEV;
- int gtf_count = gtf_length / REGS_PER_GTF;
- int ix;
+ struct ata_port *ap = dev->ap;
+ int err = -ENODEV;
+ int gtf_count = gtf_length / REGS_PER_GTF;
+ int ix;
struct taskfile_array *gtf;
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG, "%s: ENTER: port#: %d\n",
+ ata_dev_printk(dev, KERN_DEBUG, "%s: ENTER: port#: %d\n",
__FUNCTION__, ap->port_no);
if (libata_noacpi || !(ap->cbl == ATA_CBL_SATA))
return 0;
- if (!ata_dev_enabled(atadev) || (ap->flags & ATA_FLAG_DISABLED))
+ if (!ata_dev_enabled(dev) || (ap->flags & ATA_FLAG_DISABLED))
goto out;
if (!gtf_count) /* shouldn't be here */
goto out;
if (gtf_length % REGS_PER_GTF) {
if (ata_msg_drv(ap))
- ata_dev_printk(atadev, KERN_ERR,
+ ata_dev_printk(dev, KERN_ERR,
"%s: unexpected GTF length (%d)\n",
__FUNCTION__, gtf_length);
goto out;
@@ -551,7 +549,7 @@ static int do_drive_set_taskfiles(struct ata_port *ap,
(gtf_address + ix * REGS_PER_GTF);
/* send all TaskFile registers (0x1f1-0x1f7) *in*that*order* */
- taskfile_load_raw(ap, atadev, gtf);
+ taskfile_load_raw(dev, gtf);
}
err = 0;
@@ -567,11 +565,11 @@ out:
*/
int ata_acpi_exec_tfs(struct ata_port *ap)
{
- int ix;
- int ret =0;
- unsigned int gtf_length;
- unsigned long gtf_address;
- unsigned long obj_loc;
+ int ix;
+ int ret = 0;
+ unsigned int gtf_length;
+ unsigned long gtf_address;
+ unsigned long obj_loc;
if (libata_noacpi)
return 0;
@@ -584,11 +582,13 @@ int ata_acpi_exec_tfs(struct ata_port *ap)
return 0;
for (ix = 0; ix < ATA_MAX_DEVICES; ix++) {
- if (!ata_dev_enabled(&ap->device[ix]))
+ struct ata_device *dev = &ap->device[ix];
+
+ if (!ata_dev_enabled(dev))
continue;
- ret = do_drive_get_GTF(ap, ix,
- >f_length, >f_address, &obj_loc);
+ ret = do_drive_get_GTF(dev, >f_length, >f_address,
+ &obj_loc);
if (ret < 0) {
if (ata_msg_probe(ap))
ata_port_printk(ap, KERN_DEBUG,
@@ -597,8 +597,7 @@ int ata_acpi_exec_tfs(struct ata_port *ap)
break;
}
- ret = do_drive_set_taskfiles(ap, &ap->device[ix],
- gtf_length, gtf_address);
+ ret = do_drive_set_taskfiles(dev, gtf_length, gtf_address);
kfree((void *)obj_loc);
if (ret < 0) {
if (ata_msg_probe(ap))
@@ -614,8 +613,7 @@ int ata_acpi_exec_tfs(struct ata_port *ap)
/**
* ata_acpi_push_id - send Identify data to drive
- * @ap: the ata_port for the drive
- * @ix: drive index
+ * @dev: target ATA device
*
* _SDD ACPI object: for SATA mode only
* Must be after Identify (Packet) Device -- uses its data
@@ -623,57 +621,57 @@ int ata_acpi_exec_tfs(struct ata_port *ap)
* method and if it fails for whatever reason, we should still
* just keep going.
*/
-int ata_acpi_push_id(struct ata_port *ap, unsigned int ix)
+int ata_acpi_push_id(struct ata_device *dev)
{
- acpi_handle handle;
- acpi_integer pcidevfn;
- int err;
- struct device *dev = ap->host->dev;
- struct ata_device *atadev = &ap->device[ix];
- u32 dev_adr;
- acpi_status status;
- struct acpi_object_list input;
- union acpi_object in_params[1];
+ struct ata_port *ap = dev->ap;
+ acpi_handle handle;
+ acpi_integer pcidevfn;
+ int err;
+ struct device *gdev = ap->host->dev;
+ u32 dev_adr;
+ acpi_status status;
+ struct acpi_object_list input;
+ union acpi_object in_params[1];
if (libata_noacpi)
return 0;
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG, "%s: ix = %d, port#: %d\n",
- __FUNCTION__, ix, ap->port_no);
+ ata_dev_printk(dev, KERN_DEBUG, "%s: ix = %d, port#: %d\n",
+ __FUNCTION__, dev->devno, ap->port_no);
/* Don't continue if not a SATA device. */
if (!(ap->cbl == ATA_CBL_SATA)) {
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG,
+ ata_dev_printk(dev, KERN_DEBUG,
"%s: Not a SATA device\n", __FUNCTION__);
goto out;
}
/* Don't continue if device has no _ADR method.
* _SDD is intended for known motherboard devices. */
- err = sata_get_dev_handle(dev, &handle, &pcidevfn);
+ err = sata_get_dev_handle(gdev, &handle, &pcidevfn);
if (err < 0) {
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG,
+ ata_dev_printk(dev, KERN_DEBUG,
"%s: sata_get_dev_handle failed (%d\n",
__FUNCTION__, err);
goto out;
}
/* Get this drive's _ADR info, if not already known */
- if (!atadev->obj_handle) {
+ if (!dev->obj_handle) {
dev_adr = SATA_ADR_RSVD;
- err = get_sata_adr(dev, handle, pcidevfn, ix, ap, atadev,
+ err = get_sata_adr(gdev, handle, pcidevfn, dev->devno, ap, dev,
&dev_adr);
if (err < 0 || dev_adr == SATA_ADR_RSVD ||
- !atadev->obj_handle) {
+ !dev->obj_handle) {
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG,
+ ata_dev_printk(dev, KERN_DEBUG,
"%s: get_sata_adr failed: "
"err=%d, dev_adr=%u, obj_handle=0x%p\n",
__FUNCTION__, err, dev_adr,
- atadev->obj_handle);
+ dev->obj_handle);
goto out;
}
}
@@ -683,19 +681,19 @@ int ata_acpi_push_id(struct ata_port *ap, unsigned int ix)
input.count = 1;
input.pointer = in_params;
in_params[0].type = ACPI_TYPE_BUFFER;
- in_params[0].buffer.length = sizeof(atadev->id[0]) * ATA_ID_WORDS;
- in_params[0].buffer.pointer = (u8 *)atadev->id;
+ in_params[0].buffer.length = sizeof(dev->id[0]) * ATA_ID_WORDS;
+ in_params[0].buffer.pointer = (u8 *)dev->id;
/* Output buffer: _SDD has no output */
/* It's OK for _SDD to be missing too. */
- swap_buf_le16(atadev->id, ATA_ID_WORDS);
- status = acpi_evaluate_object(atadev->obj_handle, "_SDD", &input, NULL);
- swap_buf_le16(atadev->id, ATA_ID_WORDS);
+ swap_buf_le16(dev->id, ATA_ID_WORDS);
+ status = acpi_evaluate_object(dev->obj_handle, "_SDD", &input, NULL);
+ swap_buf_le16(dev->id, ATA_ID_WORDS);
err = ACPI_FAILURE(status) ? -EIO : 0;
if (err < 0) {
if (ata_msg_probe(ap))
- ata_dev_printk(atadev, KERN_DEBUG,
+ ata_dev_printk(dev, KERN_DEBUG,
"%s _SDD error: status = 0x%x\n",
__FUNCTION__, status);
}
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 4595d1f..4166407 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -101,6 +101,12 @@ int libata_noacpi = 1;
module_param_named(noacpi, libata_noacpi, int, 0444);
MODULE_PARM_DESC(noacpi, "Disables the use of ACPI in suspend/resume when set");
+int ata_spindown_compat = 1;
+module_param_named(spindown_compat, ata_spindown_compat, int, 0644);
+MODULE_PARM_DESC(spindown_compat, "Enable backward compatible spindown "
+ "behavior. Will be removed. More info can be found in "
+ "Documentation/feature-removal-schedule.txt\n");
+
MODULE_AUTHOR("Jeff Garzik");
MODULE_DESCRIPTION("Library module for ATA devices");
MODULE_LICENSE("GPL");
@@ -1654,7 +1660,7 @@ int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class,
struct ata_taskfile tf;
unsigned int err_mask = 0;
const char *reason;
- int tried_spinup = 0;
+ int may_fallback = 1, tried_spinup = 0;
int rc;
if (ata_msg_ctl(ap))
@@ -1698,11 +1704,31 @@ int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class,
return -ENOENT;
}
+ /* Device or controller might have reported the wrong
+ * device class. Give a shot at the other IDENTIFY if
+ * the current one is aborted by the device.
+ */
+ if (may_fallback &&
+ (err_mask == AC_ERR_DEV) && (tf.feature & ATA_ABORTED)) {
+ may_fallback = 0;
+
+ if (class == ATA_DEV_ATA)
+ class = ATA_DEV_ATAPI;
+ else
+ class = ATA_DEV_ATA;
+ goto retry;
+ }
+
rc = -EIO;
reason = "I/O error";
goto err_out;
}
+ /* Falling back doesn't make sense if ID data was read
+ * successfully at least once.
+ */
+ may_fallback = 0;
+
swap_buf_le16(id, ATA_ID_WORDS);
/* sanity check */
@@ -1843,7 +1869,7 @@ int ata_dev_configure(struct ata_device *dev)
ata_dev_printk(dev, KERN_DEBUG, "%s: ENTER\n", __FUNCTION__);
/* set _SDD */
- rc = ata_acpi_push_id(ap, dev->devno);
+ rc = ata_acpi_push_id(dev);
if (rc) {
ata_dev_printk(dev, KERN_WARNING, "failed to set _SDD(%d)\n",
rc);
@@ -2860,7 +2886,7 @@ int ata_do_set_mode(struct ata_port *ap, struct ata_device **r_failed_dev)
dev = &ap->device[i];
/* don't update suspended devices' xfer mode */
- if (!ata_dev_ready(dev))
+ if (!ata_dev_enabled(dev))
continue;
rc = ata_dev_set_mode(dev);
@@ -5845,37 +5871,11 @@ static int ata_host_request_pm(struct ata_host *host, pm_message_t mesg,
*/
int ata_host_suspend(struct ata_host *host, pm_message_t mesg)
{
- int i, j, rc;
+ int rc;
rc = ata_host_request_pm(host, mesg, 0, ATA_EHI_QUIET, 1);
- if (rc)
- goto fail;
-
- /* EH is quiescent now. Fail if we have any ready device.
- * This happens if hotplug occurs between completion of device
- * suspension and here.
- */
- for (i = 0; i < host->n_ports; i++) {
- struct ata_port *ap = host->ports[i];
-
- for (j = 0; j < ATA_MAX_DEVICES; j++) {
- struct ata_device *dev = &ap->device[j];
-
- if (ata_dev_ready(dev)) {
- ata_port_printk(ap, KERN_WARNING,
- "suspend failed, device %d "
- "still active\n", dev->devno);
- rc = -EBUSY;
- goto fail;
- }
- }
- }
-
- host->dev->power.power_state = mesg;
- return 0;
-
- fail:
- ata_host_resume(host);
+ if (rc == 0)
+ host->dev->power.power_state = mesg;
return rc;
}
@@ -5984,6 +5984,7 @@ struct ata_port *ata_port_alloc(struct ata_host *host)
if (!ap)
return NULL;
+ ap->pflags |= ATA_PFLAG_INITIALIZING;
ap->lock = &host->lock;
ap->flags = ATA_FLAG_DISABLED;
ap->print_id = -1;
@@ -6352,6 +6353,7 @@ int ata_host_register(struct ata_host *host, struct scsi_host_template *sht)
ehi->action |= ATA_EH_SOFTRESET;
ehi->flags |= ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET;
+ ap->pflags &= ~ATA_PFLAG_INITIALIZING;
ap->pflags |= ATA_PFLAG_LOADING;
ata_port_schedule_eh(ap);
@@ -6876,6 +6878,7 @@ EXPORT_SYMBOL_GPL(ata_timing_merge);
#ifdef CONFIG_PCI
EXPORT_SYMBOL_GPL(pci_test_config_bits);
EXPORT_SYMBOL_GPL(ata_pci_init_native_host);
+EXPORT_SYMBOL_GPL(ata_pci_init_bmdma);
EXPORT_SYMBOL_GPL(ata_pci_prepare_native_host);
EXPORT_SYMBOL_GPL(ata_pci_init_one);
EXPORT_SYMBOL_GPL(ata_pci_remove_one);
@@ -6889,11 +6892,6 @@ EXPORT_SYMBOL_GPL(ata_pci_default_filter);
EXPORT_SYMBOL_GPL(ata_pci_clear_simplex);
#endif /* CONFIG_PCI */
-#ifdef CONFIG_PM
-EXPORT_SYMBOL_GPL(ata_scsi_device_suspend);
-EXPORT_SYMBOL_GPL(ata_scsi_device_resume);
-#endif /* CONFIG_PM */
-
EXPORT_SYMBOL_GPL(ata_eng_timeout);
EXPORT_SYMBOL_GPL(ata_port_schedule_eh);
EXPORT_SYMBOL_GPL(ata_port_abort);
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 8256655..5309c31 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -77,29 +77,12 @@ static void ata_eh_finish(struct ata_port *ap);
#ifdef CONFIG_PM
static void ata_eh_handle_port_suspend(struct ata_port *ap);
static void ata_eh_handle_port_resume(struct ata_port *ap);
-static int ata_eh_suspend(struct ata_port *ap,
- struct ata_device **r_failed_dev);
-static void ata_eh_prep_resume(struct ata_port *ap);
-static int ata_eh_resume(struct ata_port *ap, struct ata_device **r_failed_dev);
#else /* CONFIG_PM */
static void ata_eh_handle_port_suspend(struct ata_port *ap)
{ }
static void ata_eh_handle_port_resume(struct ata_port *ap)
{ }
-
-static int ata_eh_suspend(struct ata_port *ap, struct ata_device **r_failed_dev)
-{
- return 0;
-}
-
-static void ata_eh_prep_resume(struct ata_port *ap)
-{ }
-
-static int ata_eh_resume(struct ata_port *ap, struct ata_device **r_failed_dev)
-{
- return 0;
-}
#endif /* CONFIG_PM */
static void ata_ering_record(struct ata_ering *ering, int is_io,
@@ -568,6 +551,9 @@ void ata_port_schedule_eh(struct ata_port *ap)
{
WARN_ON(!ap->ops->error_handler);
+ if (ap->pflags & ATA_PFLAG_INITIALIZING)
+ return;
+
ap->pflags |= ATA_PFLAG_EH_PENDING;
scsi_schedule_eh(ap->scsi_host);
@@ -1791,7 +1777,7 @@ static int ata_eh_revalidate_and_attach(struct ata_port *ap,
if (ehc->i.flags & ATA_EHI_DID_RESET)
readid_flags |= ATA_READID_POSTRESET;
- if (action & ATA_EH_REVALIDATE && ata_dev_ready(dev)) {
+ if ((action & ATA_EH_REVALIDATE) && ata_dev_enabled(dev)) {
if (ata_port_offline(ap)) {
rc = -EIO;
goto err;
@@ -1872,166 +1858,6 @@ static int ata_eh_revalidate_and_attach(struct ata_port *ap,
return rc;
}
-#ifdef CONFIG_PM
-/**
- * ata_eh_suspend - handle suspend EH action
- * @ap: target host port
- * @r_failed_dev: result parameter to indicate failing device
- *
- * Handle suspend EH action. Disk devices are spinned down and
- * other types of devices are just marked suspended. Once
- * suspended, no EH action to the device is allowed until it is
- * resumed.
- *
- * LOCKING:
- * Kernel thread context (may sleep).
- *
- * RETURNS:
- * 0 on success, -errno otherwise
- */
-static int ata_eh_suspend(struct ata_port *ap, struct ata_device **r_failed_dev)
-{
- struct ata_device *dev;
- int i, rc = 0;
-
- DPRINTK("ENTER\n");
-
- for (i = 0; i < ATA_MAX_DEVICES; i++) {
- unsigned long flags;
- unsigned int action, err_mask;
-
- dev = &ap->device[i];
- action = ata_eh_dev_action(dev);
-
- if (!ata_dev_enabled(dev) || !(action & ATA_EH_SUSPEND))
- continue;
-
- WARN_ON(dev->flags & ATA_DFLAG_SUSPENDED);
-
- ata_eh_about_to_do(ap, dev, ATA_EH_SUSPEND);
-
- if (dev->class == ATA_DEV_ATA && !(action & ATA_EH_PM_FREEZE)) {
- /* flush cache */
- rc = ata_flush_cache(dev);
- if (rc)
- break;
-
- /* spin down */
- err_mask = ata_do_simple_cmd(dev, ATA_CMD_STANDBYNOW1);
- if (err_mask) {
- ata_dev_printk(dev, KERN_ERR, "failed to "
- "spin down (err_mask=0x%x)\n",
- err_mask);
- rc = -EIO;
- break;
- }
- }
-
- spin_lock_irqsave(ap->lock, flags);
- dev->flags |= ATA_DFLAG_SUSPENDED;
- spin_unlock_irqrestore(ap->lock, flags);
-
- ata_eh_done(ap, dev, ATA_EH_SUSPEND);
- }
-
- if (rc)
- *r_failed_dev = dev;
-
- DPRINTK("EXIT\n");
- return rc;
-}
-
-/**
- * ata_eh_prep_resume - prep for resume EH action
- * @ap: target host port
- *
- * Clear SUSPENDED in preparation for scheduled resume actions.
- * This allows other parts of EH to access the devices being
- * resumed.
- *
- * LOCKING:
- * Kernel thread context (may sleep).
- */
-static void ata_eh_prep_resume(struct ata_port *ap)
-{
- struct ata_device *dev;
- unsigned long flags;
- int i;
-
- DPRINTK("ENTER\n");
-
- for (i = 0; i < ATA_MAX_DEVICES; i++) {
- unsigned int action;
-
- dev = &ap->device[i];
- action = ata_eh_dev_action(dev);
-
- if (!ata_dev_enabled(dev) || !(action & ATA_EH_RESUME))
- continue;
-
- spin_lock_irqsave(ap->lock, flags);
- dev->flags &= ~ATA_DFLAG_SUSPENDED;
- spin_unlock_irqrestore(ap->lock, flags);
- }
-
- DPRINTK("EXIT\n");
-}
-
-/**
- * ata_eh_resume - handle resume EH action
- * @ap: target host port
- * @r_failed_dev: result parameter to indicate failing device
- *
- * Handle resume EH action. Target devices are already reset and
- * revalidated. Spinning up is the only operation left.
- *
- * LOCKING:
- * Kernel thread context (may sleep).
- *
- * RETURNS:
- * 0 on success, -errno otherwise
- */
-static int ata_eh_resume(struct ata_port *ap, struct ata_device **r_failed_dev)
-{
- struct ata_device *dev;
- int i, rc = 0;
-
- DPRINTK("ENTER\n");
-
- for (i = 0; i < ATA_MAX_DEVICES; i++) {
- unsigned int action, err_mask;
-
- dev = &ap->device[i];
- action = ata_eh_dev_action(dev);
-
- if (!ata_dev_enabled(dev) || !(action & ATA_EH_RESUME))
- continue;
-
- ata_eh_about_to_do(ap, dev, ATA_EH_RESUME);
-
- if (dev->class == ATA_DEV_ATA && !(action & ATA_EH_PM_FREEZE)) {
- err_mask = ata_do_simple_cmd(dev,
- ATA_CMD_IDLEIMMEDIATE);
- if (err_mask) {
- ata_dev_printk(dev, KERN_ERR, "failed to "
- "spin up (err_mask=0x%x)\n",
- err_mask);
- rc = -EIO;
- break;
- }
- }
-
- ata_eh_done(ap, dev, ATA_EH_RESUME);
- }
-
- if (rc)
- *r_failed_dev = dev;
-
- DPRINTK("EXIT\n");
- return 0;
-}
-#endif /* CONFIG_PM */
-
static int ata_port_nr_enabled(struct ata_port *ap)
{
int i, cnt = 0;
@@ -2057,17 +1883,6 @@ static int ata_eh_skip_recovery(struct ata_port *ap)
struct ata_eh_context *ehc = &ap->eh_context;
int i;
- /* skip if all possible devices are suspended */
- for (i = 0; i < ata_port_max_devices(ap); i++) {
- struct ata_device *dev = &ap->device[i];
-
- if (!(dev->flags & ATA_DFLAG_SUSPENDED))
- break;
- }
-
- if (i == ata_port_max_devices(ap))
- return 1;
-
/* thaw frozen port, resume link and recover failed devices */
if ((ap->pflags & ATA_PFLAG_FROZEN) ||
(ehc->i.flags & ATA_EHI_RESUME_LINK) || ata_port_nr_enabled(ap))
@@ -2147,9 +1962,6 @@ static int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
if (ap->pflags & ATA_PFLAG_UNLOADING)
goto out;
- /* prep for resume */
- ata_eh_prep_resume(ap);
-
/* skip EH if possible. */
if (ata_eh_skip_recovery(ap))
ehc->i.action = 0;
@@ -2177,11 +1989,6 @@ static int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
if (rc)
goto dev_fail;
- /* resume devices */
- rc = ata_eh_resume(ap, &dev);
- if (rc)
- goto dev_fail;
-
/* configure transfer mode if necessary */
if (ehc->i.flags & ATA_EHI_SETMODE) {
rc = ata_set_mode(ap, &dev);
@@ -2190,25 +1997,16 @@ static int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
ehc->i.flags &= ~ATA_EHI_SETMODE;
}
- /* suspend devices */
- rc = ata_eh_suspend(ap, &dev);
- if (rc)
- goto dev_fail;
-
goto out;
dev_fail:
ehc->tries[dev->devno]--;
switch (rc) {
- case -EINVAL:
- /* eeek, something went very wrong, give up */
- ehc->tries[dev->devno] = 0;
- break;
-
case -ENODEV:
/* device missing or wrong IDENTIFY data, schedule probing */
ehc->i.probe_mask |= (1 << dev->devno);
+ case -EINVAL:
/* give it just one more chance */
ehc->tries[dev->devno] = min(ehc->tries[dev->devno], 1);
case -EIO:
@@ -2390,22 +2188,13 @@ static void ata_eh_handle_port_suspend(struct ata_port *ap)
*
* Resume @ap.
*
- * This function also waits upto one second until all devices
- * hanging off this port requests resume EH action. This is to
- * prevent invoking EH and thus reset multiple times on resume.
- *
- * On DPM resume, where some of devices might not be resumed
- * together, this may delay port resume upto one second, but such
- * DPM resumes are rare and 1 sec delay isn't too bad.
- *
* LOCKING:
* Kernel thread context (may sleep).
*/
static void ata_eh_handle_port_resume(struct ata_port *ap)
{
- unsigned long timeout;
unsigned long flags;
- int i, rc = 0;
+ int rc = 0;
/* are we resuming? */
spin_lock_irqsave(ap->lock, flags);
@@ -2416,31 +2205,12 @@ static void ata_eh_handle_port_resume(struct ata_port *ap)
}
spin_unlock_irqrestore(ap->lock, flags);
- /* spurious? */
- if (!(ap->pflags & ATA_PFLAG_SUSPENDED))
- goto done;
+ WARN_ON(!(ap->pflags & ATA_PFLAG_SUSPENDED));
if (ap->ops->port_resume)
rc = ap->ops->port_resume(ap);
- /* give devices time to request EH */
- timeout = jiffies + HZ; /* 1s max */
- while (1) {
- for (i = 0; i < ATA_MAX_DEVICES; i++) {
- struct ata_device *dev = &ap->device[i];
- unsigned int action = ata_eh_dev_action(dev);
-
- if ((dev->flags & ATA_DFLAG_SUSPENDED) &&
- !(action & ATA_EH_RESUME))
- break;
- }
-
- if (i == ATA_MAX_DEVICES || time_after(jiffies, timeout))
- break;
- msleep(10);
- }
-
- done:
+ /* report result */
spin_lock_irqsave(ap->lock, flags);
ap->pflags &= ~(ATA_PFLAG_PM_PENDING | ATA_PFLAG_SUSPENDED);
if (ap->pm_result) {
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 9afba2b..dd81fa7 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -510,133 +510,6 @@ static void ata_dump_status(unsigned id, struct ata_taskfile *tf)
}
}
-#ifdef CONFIG_PM
-/**
- * ata_scsi_device_suspend - suspend ATA device associated with sdev
- * @sdev: the SCSI device to suspend
- * @mesg: target power management message
- *
- * Request suspend EH action on the ATA device associated with
- * @sdev and wait for the operation to complete.
- *
- * LOCKING:
- * Kernel thread context (may sleep).
- *
- * RETURNS:
- * 0 on success, -errno otherwise.
- */
-int ata_scsi_device_suspend(struct scsi_device *sdev, pm_message_t mesg)
-{
- struct ata_port *ap = ata_shost_to_port(sdev->host);
- struct ata_device *dev = ata_scsi_find_dev(ap, sdev);
- unsigned long flags;
- unsigned int action;
- int rc = 0;
-
- if (!dev)
- goto out;
-
- spin_lock_irqsave(ap->lock, flags);
-
- /* wait for the previous resume to complete */
- while (dev->flags & ATA_DFLAG_SUSPENDED) {
- spin_unlock_irqrestore(ap->lock, flags);
- ata_port_wait_eh(ap);
- spin_lock_irqsave(ap->lock, flags);
- }
-
- /* if @sdev is already detached, nothing to do */
- if (sdev->sdev_state == SDEV_OFFLINE ||
- sdev->sdev_state == SDEV_CANCEL || sdev->sdev_state == SDEV_DEL)
- goto out_unlock;
-
- /* request suspend */
- action = ATA_EH_SUSPEND;
- if (mesg.event != PM_EVENT_SUSPEND)
- action |= ATA_EH_PM_FREEZE;
- ap->eh_info.dev_action[dev->devno] |= action;
- ap->eh_info.flags |= ATA_EHI_QUIET;
- ata_port_schedule_eh(ap);
-
- spin_unlock_irqrestore(ap->lock, flags);
-
- /* wait for EH to do the job */
- ata_port_wait_eh(ap);
-
- spin_lock_irqsave(ap->lock, flags);
-
- /* If @sdev is still attached but the associated ATA device
- * isn't suspended, the operation failed.
- */
- if (sdev->sdev_state != SDEV_OFFLINE &&
- sdev->sdev_state != SDEV_CANCEL && sdev->sdev_state != SDEV_DEL &&
- !(dev->flags & ATA_DFLAG_SUSPENDED))
- rc = -EIO;
-
- out_unlock:
- spin_unlock_irqrestore(ap->lock, flags);
- out:
- if (rc == 0)
- sdev->sdev_gendev.power.power_state = mesg;
- return rc;
-}
-
-/**
- * ata_scsi_device_resume - resume ATA device associated with sdev
- * @sdev: the SCSI device to resume
- *
- * Request resume EH action on the ATA device associated with
- * @sdev and return immediately. This enables parallel
- * wakeup/spinup of devices.
- *
- * LOCKING:
- * Kernel thread context (may sleep).
- *
- * RETURNS:
- * 0.
- */
-int ata_scsi_device_resume(struct scsi_device *sdev)
-{
- struct ata_port *ap = ata_shost_to_port(sdev->host);
- struct ata_device *dev = ata_scsi_find_dev(ap, sdev);
- struct ata_eh_info *ehi = &ap->eh_info;
- unsigned long flags;
- unsigned int action;
-
- if (!dev)
- goto out;
-
- spin_lock_irqsave(ap->lock, flags);
-
- /* if @sdev is already detached, nothing to do */
- if (sdev->sdev_state == SDEV_OFFLINE ||
- sdev->sdev_state == SDEV_CANCEL || sdev->sdev_state == SDEV_DEL)
- goto out_unlock;
-
- /* request resume */
- action = ATA_EH_RESUME;
- if (sdev->sdev_gendev.power.power_state.event == PM_EVENT_SUSPEND)
- __ata_ehi_hotplugged(ehi);
- else
- action |= ATA_EH_PM_FREEZE | ATA_EH_SOFTRESET;
- ehi->dev_action[dev->devno] |= action;
-
- /* We don't want autopsy and verbose EH messages. Disable
- * those if we're the only device on this link.
- */
- if (ata_port_max_devices(ap) == 1)
- ehi->flags |= ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET;
-
- ata_port_schedule_eh(ap);
-
- out_unlock:
- spin_unlock_irqrestore(ap->lock, flags);
- out:
- sdev->sdev_gendev.power.power_state = PMSG_ON;
- return 0;
-}
-#endif /* CONFIG_PM */
-
/**
* ata_to_sense_error - convert ATA error to SCSI error
* @id: ATA device number
@@ -929,6 +802,8 @@ int ata_scsi_slave_config(struct scsi_device *sdev)
blk_queue_max_phys_segments(sdev->request_queue, LIBATA_MAX_PRD);
+ sdev->manage_start_stop = 1;
+
if (dev)
ata_scsi_dev_config(sdev, dev);
@@ -1069,9 +944,35 @@ static unsigned int ata_scsi_start_stop_xlat(struct ata_queued_cmd *qc)
}
tf->command = ATA_CMD_VERIFY; /* READ VERIFY */
- } else
+ } else {
+ /* XXX: This is for backward compatibility, will be
+ * removed. Read Documentation/feature-removal-schedule.txt
+ * for more info.
+ */
+ if (ata_spindown_compat &&
+ (system_state == SYSTEM_HALT ||
+ system_state == SYSTEM_POWER_OFF)) {
+ static int warned = 0;
+
+ if (!warned) {
+ spin_unlock_irq(qc->ap->lock);
+ ata_dev_printk(qc->dev, KERN_WARNING,
+ "DISK MIGHT NOT BE SPUN DOWN PROPERLY. "
+ "UPDATE SHUTDOWN UTILITY\n");
+ ata_dev_printk(qc->dev, KERN_WARNING,
+ "For more info, visit "
+ "http://linux-ata.org/shutdown.html\n");
+ warned = 1;
+ ssleep(5);
+ spin_lock_irq(qc->ap->lock);
+ }
+ scmd->result = SAM_STAT_GOOD;
+ return 1;
+ }
+
/* Issue ATA STANDBY IMMEDIATE command */
tf->command = ATA_CMD_STANDBYNOW1;
+ }
/*
* Standby and Idle condition timers could be implemented but that
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index d211db6..e35d134 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -544,7 +544,7 @@ static int ata_resources_present(struct pci_dev *pdev, int port)
* RETURNS:
* 0 on success, -errno otherwise.
*/
-static int ata_pci_init_bmdma(struct ata_host *host)
+int ata_pci_init_bmdma(struct ata_host *host)
{
struct device *gdev = host->dev;
struct pci_dev *pdev = to_pci_dev(gdev);
@@ -566,7 +566,7 @@ static int ata_pci_init_bmdma(struct ata_host *host)
}
host->iomap = pcim_iomap_table(pdev);
- for (i = 0; i < host->n_ports; i++) {
+ for (i = 0; i < 2; i++) {
struct ata_port *ap = host->ports[i];
void __iomem *bmdma = host->iomap[4] + 8 * i;
@@ -585,54 +585,52 @@ static int ata_pci_init_bmdma(struct ata_host *host)
/**
* ata_pci_init_native_host - acquire native ATA resources and init host
* @host: target ATA host
- * @port_mask: ports to consider
*
- * Acquire native PCI ATA resources for @host and initialize
- * @host accordoingly.
+ * Acquire native PCI ATA resources for @host and initialize the
+ * first two ports of @host accordingly. Ports marked dummy are
+ * skipped and allocation failure makes the port dummy.
*
* LOCKING:
* Inherited from calling layer (may sleep).
*
* RETURNS:
- * 0 on success, -errno otherwise.
+ * 0 if at least one port is initialized, -ENODEV if no port is
+ * available.
*/
-int ata_pci_init_native_host(struct ata_host *host, unsigned int port_mask)
+int ata_pci_init_native_host(struct ata_host *host)
{
struct device *gdev = host->dev;
struct pci_dev *pdev = to_pci_dev(gdev);
+ unsigned int mask = 0;
int i, rc;
- /* Discard disabled ports. Some controllers show their unused
- * channels this way. Disabled ports are made dummy.
- */
- for (i = 0; i < 2; i++) {
- if ((port_mask & (1 << i)) && !ata_resources_present(pdev, i)) {
- host->ports[i]->ops = &ata_dummy_port_ops;
- port_mask &= ~(1 << i);
- }
- }
-
- if (!port_mask) {
- dev_printk(KERN_ERR, gdev, "no available port\n");
- return -ENODEV;
- }
-
/* request, iomap BARs and init port addresses accordingly */
for (i = 0; i < 2; i++) {
struct ata_port *ap = host->ports[i];
int base = i * 2;
void __iomem * const *iomap;
- if (!(port_mask & (1 << i)))
+ if (ata_port_is_dummy(ap))
+ continue;
+
+ /* Discard disabled ports. Some controllers show
+ * their unused channels this way. Disabled ports are
+ * made dummy.
+ */
+ if (!ata_resources_present(pdev, i)) {
+ ap->ops = &ata_dummy_port_ops;
continue;
+ }
rc = pcim_iomap_regions(pdev, 0x3 << base, DRV_NAME);
if (rc) {
- dev_printk(KERN_ERR, gdev, "failed to request/iomap "
- "BARs for port %d (errno=%d)\n", i, rc);
+ dev_printk(KERN_WARNING, gdev,
+ "failed to request/iomap BARs for port %d "
+ "(errno=%d)\n", i, rc);
if (rc == -EBUSY)
pcim_pin_device(pdev);
- return rc;
+ ap->ops = &ata_dummy_port_ops;
+ continue;
}
host->iomap = iomap = pcim_iomap_table(pdev);
@@ -641,6 +639,13 @@ int ata_pci_init_native_host(struct ata_host *host, unsigned int port_mask)
ap->ioaddr.ctl_addr = (void __iomem *)
((unsigned long)iomap[base + 1] | ATA_PCI_CTL_OFS);
ata_std_ports(&ap->ioaddr);
+
+ mask |= 1 << i;
+ }
+
+ if (!mask) {
+ dev_printk(KERN_ERR, gdev, "no available native port\n");
+ return -ENODEV;
}
return 0;
@@ -649,8 +654,7 @@ int ata_pci_init_native_host(struct ata_host *host, unsigned int port_mask)
/**
* ata_pci_prepare_native_host - helper to prepare native PCI ATA host
* @pdev: target PCI device
- * @ppi: array of port_info
- * @n_ports: number of ports to allocate
+ * @ppi: array of port_info, must be enough for two ports
* @r_host: out argument for the initialized ATA host
*
* Helper to allocate ATA host for @pdev, acquire all native PCI
@@ -664,10 +668,9 @@ int ata_pci_init_native_host(struct ata_host *host, unsigned int port_mask)
*/
int ata_pci_prepare_native_host(struct pci_dev *pdev,
const struct ata_port_info * const * ppi,
- int n_ports, struct ata_host **r_host)
+ struct ata_host **r_host)
{
struct ata_host *host;
- unsigned int port_mask;
int rc;
if (!devres_open_group(&pdev->dev, NULL, GFP_KERNEL))
@@ -681,11 +684,7 @@ int ata_pci_prepare_native_host(struct pci_dev *pdev,
goto err_out;
}
- port_mask = ATA_PORT_PRIMARY;
- if (n_ports > 1)
- port_mask |= ATA_PORT_SECONDARY;
-
- rc = ata_pci_init_native_host(host, port_mask);
+ rc = ata_pci_init_native_host(host);
if (rc)
goto err_out;
@@ -777,8 +776,11 @@ static int ata_init_legacy_port(struct ata_port *ap,
/* iomap cmd and ctl ports */
legacy_dr->cmd_addr[port_no] = ioport_map(cmd_port, 8);
legacy_dr->ctl_addr[port_no] = ioport_map(ctl_port, 1);
- if (!legacy_dr->cmd_addr[port_no] || !legacy_dr->ctl_addr[port_no])
+ if (!legacy_dr->cmd_addr[port_no] || !legacy_dr->ctl_addr[port_no]) {
+ dev_printk(KERN_WARNING, host->dev,
+ "failed to map cmd/ctl ports\n");
return -ENOMEM;
+ }
/* init IO addresses */
ap->ioaddr.cmd_addr = legacy_dr->cmd_addr[port_no];
@@ -792,19 +794,20 @@ static int ata_init_legacy_port(struct ata_port *ap,
/**
* ata_init_legacy_host - acquire legacy ATA resources and init ATA host
* @host: target ATA host
- * @legacy_mask: out parameter, mask indicating ports is in legacy mode
* @was_busy: out parameter, indicates whether any port was busy
*
- * Acquire legacy ATA resources for ports.
+ * Acquire legacy ATA resources for the first two ports of @host
+ * and initialize it accordingly. Ports marked dummy are skipped
+ * and resource acquistion failure makes the port dummy.
*
* LOCKING:
* Inherited from calling layer (may sleep).
*
* RETURNS:
- * 0 on success, -errno otherwise.
+ * 0 if at least one port is initialized, -ENODEV if no port is
+ * available.
*/
-static int ata_init_legacy_host(struct ata_host *host,
- unsigned int *legacy_mask, int *was_busy)
+static int ata_init_legacy_host(struct ata_host *host, int *was_busy)
{
struct device *gdev = host->dev;
struct ata_legacy_devres *legacy_dr;
@@ -821,22 +824,23 @@ static int ata_init_legacy_host(struct ata_host *host,
devres_add(gdev, legacy_dr);
for (i = 0; i < 2; i++) {
- *legacy_mask &= ~(1 << i);
+ if (ata_port_is_dummy(host->ports[i]))
+ continue;
+
rc = ata_init_legacy_port(host->ports[i], legacy_dr);
if (rc == 0)
legacy_dr->mask |= 1 << i;
- else if (rc == -EBUSY)
- (*was_busy)++;
- }
-
- if (!legacy_dr->mask)
- return -EBUSY;
-
- for (i = 0; i < 2; i++)
- if (!(legacy_dr->mask & (1 << i)))
+ else {
+ if (rc == -EBUSY)
+ (*was_busy)++;
host->ports[i]->ops = &ata_dummy_port_ops;
+ }
+ }
- *legacy_mask |= legacy_dr->mask;
+ if (!legacy_dr->mask) {
+ dev_printk(KERN_ERR, gdev, "no available legacy port\n");
+ return -ENODEV;
+ }
devres_remove_group(gdev, NULL);
return 0;
@@ -875,7 +879,7 @@ static int ata_request_legacy_irqs(struct ata_host *host,
legacy_dr = devres_find(host->dev, ata_legacy_release, NULL, NULL);
BUG_ON(!legacy_dr);
- for (i = 0; i < host->n_ports; i++) {
+ for (i = 0; i < 2; i++) {
unsigned int irq;
/* FIXME: ATA_*_IRQ() should take generic device not pci_dev */
@@ -923,8 +927,7 @@ static int ata_request_legacy_irqs(struct ata_host *host,
/**
* ata_pci_init_one - Initialize/register PCI IDE host controller
* @pdev: Controller to be initialized
- * @port_info: Information from low-level host driver
- * @n_ports: Number of ports attached to host controller
+ * @ppi: array of port_info, must be enough for two ports
*
* This is a helper function which can be called from a driver's
* xxx_init_one() probe function if the hardware uses traditional
@@ -944,26 +947,34 @@ static int ata_request_legacy_irqs(struct ata_host *host,
* RETURNS:
* Zero on success, negative on errno-based value on error.
*/
-
-int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
- unsigned int n_ports)
+int ata_pci_init_one(struct pci_dev *pdev,
+ const struct ata_port_info * const * ppi)
{
struct device *dev = &pdev->dev;
+ const struct ata_port_info *pi = NULL;
struct ata_host *host = NULL;
- const struct ata_port_info *port[2];
u8 mask;
- unsigned int legacy_mode = 0;
- int rc;
+ int legacy_mode = 0;
+ int i, rc;
DPRINTK("ENTER\n");
- if (!devres_open_group(dev, NULL, GFP_KERNEL))
- return -ENOMEM;
+ /* look up the first valid port_info */
+ for (i = 0; i < 2 && ppi[i]; i++) {
+ if (ppi[i]->port_ops != &ata_dummy_port_ops) {
+ pi = ppi[i];
+ break;
+ }
+ }
- BUG_ON(n_ports < 1 || n_ports > 2);
+ if (!pi) {
+ dev_printk(KERN_ERR, &pdev->dev,
+ "no valid port_info specified\n");
+ return -EINVAL;
+ }
- port[0] = port_info[0];
- port[1] = (n_ports > 1) ? port_info[1] : NULL;
+ if (!devres_open_group(dev, NULL, GFP_KERNEL))
+ return -ENOMEM;
/* FIXME: Really for ATA it isn't safe because the device may be
multi-purpose and we want to leave it alone if it was already
@@ -984,7 +995,7 @@ int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
pci_read_config_byte(pdev, PCI_CLASS_PROG, &tmp8);
mask = (1 << 2) | (1 << 0);
if ((tmp8 & mask) != mask)
- legacy_mode = (1 << 3);
+ legacy_mode = 1;
#if defined(CONFIG_NO_ATA_LEGACY)
/* Some platforms with PCI limits cannot address compat
port space. In that case we punt if their firmware has
@@ -998,7 +1009,7 @@ int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
}
/* alloc and init host */
- host = ata_host_alloc_pinfo(dev, port, n_ports);
+ host = ata_host_alloc_pinfo(dev, ppi, 2);
if (!host) {
dev_printk(KERN_ERR, &pdev->dev,
"failed to allocate ATA host\n");
@@ -1007,19 +1018,13 @@ int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
}
if (!legacy_mode) {
- unsigned int port_mask;
-
- port_mask = ATA_PORT_PRIMARY;
- if (n_ports > 1)
- port_mask |= ATA_PORT_SECONDARY;
-
- rc = ata_pci_init_native_host(host, port_mask);
+ rc = ata_pci_init_native_host(host);
if (rc)
goto err_out;
} else {
int was_busy = 0;
- rc = ata_init_legacy_host(host, &legacy_mode, &was_busy);
+ rc = ata_init_legacy_host(host, &was_busy);
if (was_busy)
pcim_pin_device(pdev);
if (rc)
@@ -1040,8 +1045,7 @@ int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
goto err_out;
if (!legacy_mode)
- rc = devm_request_irq(dev, pdev->irq,
- port_info[0]->port_ops->irq_handler,
+ rc = devm_request_irq(dev, pdev->irq, pi->port_ops->irq_handler,
IRQF_SHARED, DRV_NAME, host);
else {
irq_handler_t handler[2] = { host->ops->irq_handler,
@@ -1055,7 +1059,7 @@ int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
goto err_out;
/* register */
- rc = ata_host_register(host, port_info[0]->sht);
+ rc = ata_host_register(host, pi->sht);
if (rc)
goto err_out;
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index 5f4d40c..8b71b73 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -58,6 +58,7 @@ extern int atapi_enabled;
extern int atapi_dmadir;
extern int libata_fua;
extern int libata_noacpi;
+extern int ata_spindown_compat;
extern struct ata_queued_cmd *ata_qc_new_init(struct ata_device *dev);
extern int ata_build_rw_tf(struct ata_taskfile *tf, struct ata_device *dev,
u64 block, u32 n_block, unsigned int tf_flags,
@@ -96,15 +97,15 @@ extern int ata_cmd_ioctl(struct scsi_device *scsidev, void __user *arg);
extern struct ata_port *ata_port_alloc(struct ata_host *host);
/* libata-acpi.c */
-#ifdef CONFIG_SATA_ACPI
+#ifdef CONFIG_ATA_ACPI
extern int ata_acpi_exec_tfs(struct ata_port *ap);
-extern int ata_acpi_push_id(struct ata_port *ap, unsigned int ix);
+extern int ata_acpi_push_id(struct ata_device *dev);
#else
static inline int ata_acpi_exec_tfs(struct ata_port *ap)
{
return 0;
}
-static inline int ata_acpi_push_id(struct ata_port *ap, unsigned int ix)
+static inline int ata_acpi_push_id(struct ata_device *dev)
{
return 0;
}
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index d40edeb..3c55a5f 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -291,10 +291,6 @@ static struct scsi_host_template ali_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
/*
@@ -522,14 +518,14 @@ static void ali_init_chipset(struct pci_dev *pdev)
static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
- static struct ata_port_info info_early = {
+ static const struct ata_port_info info_early = {
.sht = &ali_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.port_ops = &ali_early_port_ops
};
/* Revision 0x20 added DMA */
- static struct ata_port_info info_20 = {
+ static const struct ata_port_info info_20 = {
.sht = &ali_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
.pio_mask = 0x1f,
@@ -537,7 +533,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &ali_20_port_ops
};
/* Revision 0x20 with support logic added UDMA */
- static struct ata_port_info info_20_udma = {
+ static const struct ata_port_info info_20_udma = {
.sht = &ali_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
.pio_mask = 0x1f,
@@ -546,7 +542,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &ali_20_port_ops
};
/* Revision 0xC2 adds UDMA66 */
- static struct ata_port_info info_c2 = {
+ static const struct ata_port_info info_c2 = {
.sht = &ali_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
.pio_mask = 0x1f,
@@ -555,7 +551,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &ali_c2_port_ops
};
/* Revision 0xC3 is UDMA100 */
- static struct ata_port_info info_c3 = {
+ static const struct ata_port_info info_c3 = {
.sht = &ali_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
.pio_mask = 0x1f,
@@ -564,7 +560,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &ali_c2_port_ops
};
/* Revision 0xC4 is UDMA133 */
- static struct ata_port_info info_c4 = {
+ static const struct ata_port_info info_c4 = {
.sht = &ali_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
.pio_mask = 0x1f,
@@ -573,7 +569,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &ali_c2_port_ops
};
/* Revision 0xC5 is UDMA133 with LBA48 DMA */
- static struct ata_port_info info_c5 = {
+ static const struct ata_port_info info_c5 = {
.sht = &ali_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -582,7 +578,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &ali_c5_port_ops
};
- static struct ata_port_info *port_info[2];
+ const struct ata_port_info *ppi[] = { NULL, NULL };
u8 rev, tmp;
struct pci_dev *isa_bridge;
@@ -594,17 +590,17 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
*/
if (rev < 0x20) {
- port_info[0] = port_info[1] = &info_early;
+ ppi[0] = &info_early;
} else if (rev < 0xC2) {
- port_info[0] = port_info[1] = &info_20;
+ ppi[0] = &info_20;
} else if (rev == 0xC2) {
- port_info[0] = port_info[1] = &info_c2;
+ ppi[0] = &info_c2;
} else if (rev == 0xC3) {
- port_info[0] = port_info[1] = &info_c3;
+ ppi[0] = &info_c3;
} else if (rev == 0xC4) {
- port_info[0] = port_info[1] = &info_c4;
+ ppi[0] = &info_c4;
} else
- port_info[0] = port_info[1] = &info_c5;
+ ppi[0] = &info_c5;
ali_init_chipset(pdev);
@@ -613,10 +609,10 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
/* Are we paired with a UDMA capable chip */
pci_read_config_byte(isa_bridge, 0x5E, &tmp);
if ((tmp & 0x1E) == 0x12)
- port_info[0] = port_info[1] = &info_20_udma;
+ ppi[0] = &info_20_udma;
pci_dev_put(isa_bridge);
}
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index 67c7e87..b439351 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -324,10 +324,6 @@ static struct scsi_host_template amd_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations amd33_port_ops = {
@@ -542,7 +538,7 @@ static struct ata_port_operations nv133_port_ops = {
static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
- static struct ata_port_info info[10] = {
+ static const struct ata_port_info info[10] = {
{ /* 0: AMD 7401 */
.sht = &amd_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
@@ -624,7 +620,7 @@ static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &amd100_port_ops
}
};
- static struct ata_port_info *port_info[2];
+ const struct ata_port_info *ppi[] = { NULL, NULL };
static int printed_version;
int type = id->driver_data;
u8 rev;
@@ -656,9 +652,8 @@ static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
ata_pci_clear_simplex(pdev);
/* And fire it up */
-
- port_info[0] = port_info[1] = &info[type];
- return ata_pci_init_one(pdev, port_info, 2);
+ ppi[0] = &info[type];
+ return ata_pci_init_one(pdev, ppi);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
index ef51940..9861059 100644
--- a/drivers/ata/pata_artop.c
+++ b/drivers/ata/pata_artop.c
@@ -414,7 +414,7 @@ static const struct ata_port_operations artop6260_ops = {
static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
{
static int printed_version;
- static struct ata_port_info info_6210 = {
+ static const struct ata_port_info info_6210 = {
.sht = &artop_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
@@ -422,7 +422,7 @@ static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
.udma_mask = ATA_UDMA2,
.port_ops = &artop6210_ops,
};
- static struct ata_port_info info_626x = {
+ static const struct ata_port_info info_626x = {
.sht = &artop_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
@@ -430,7 +430,7 @@ static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
.udma_mask = ATA_UDMA4,
.port_ops = &artop6260_ops,
};
- static struct ata_port_info info_626x_fast = {
+ static const struct ata_port_info info_626x_fast = {
.sht = &artop_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
@@ -438,32 +438,30 @@ static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
.udma_mask = ATA_UDMA5,
.port_ops = &artop6260_ops,
};
- struct ata_port_info *port_info[2];
- struct ata_port_info *info = NULL;
- int ports = 2;
+ const struct ata_port_info *ppi[] = { NULL, NULL };
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
if (id->driver_data == 0) { /* 6210 variant */
- info = &info_6210;
+ ppi[0] = &info_6210;
+ ppi[1] = &ata_dummy_port_info;
/* BIOS may have left us in UDMA, clear it before libata probe */
pci_write_config_byte(pdev, 0x54, 0);
/* For the moment (also lacks dsc) */
printk(KERN_WARNING "ARTOP 6210 requires serialize functionality not yet supported by libata.\n");
printk(KERN_WARNING "Secondary ATA ports will not be activated.\n");
- ports = 1;
}
else if (id->driver_data == 1) /* 6260 */
- info = &info_626x;
+ ppi[0] = &info_626x;
else if (id->driver_data == 2) { /* 6260 or 6260 + fast */
unsigned long io = pci_resource_start(pdev, 4);
u8 reg;
- info = &info_626x;
+ ppi[0] = &info_626x;
if (inb(io) & 0x10)
- info = &info_626x_fast;
+ ppi[0] = &info_626x_fast;
/* Mac systems come up with some registers not set as we
will need them */
@@ -484,10 +482,9 @@ static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
}
- BUG_ON(info == NULL);
+ BUG_ON(ppi[0] == NULL);
- port_info[0] = port_info[1] = info;
- return ata_pci_init_one(pdev, port_info, ports);
+ return ata_pci_init_one(pdev, ppi);
}
static const struct pci_device_id artop_pci_tbl[] = {
diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
index 2151538..8449146 100644
--- a/drivers/ata/pata_atiixp.c
+++ b/drivers/ata/pata_atiixp.c
@@ -229,10 +229,6 @@ static struct scsi_host_template atiixp_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations atiixp_port_ops = {
@@ -272,7 +268,7 @@ static struct ata_port_operations atiixp_port_ops = {
static int atiixp_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &atiixp_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -280,8 +276,8 @@ static int atiixp_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.udma_mask = 0x3F,
.port_ops = &atiixp_port_ops
};
- static struct ata_port_info *port_info[2] = { &info, &info };
- return ata_pci_init_one(dev, port_info, 2);
+ const struct ata_port_info *ppi[] = { &info, NULL };
+ return ata_pci_init_one(dev, ppi);
}
static const struct pci_device_id atiixp[] = {
diff --git a/drivers/ata/pata_cmd640.c b/drivers/ata/pata_cmd640.c
index 2105985..ed00fa9 100644
--- a/drivers/ata/pata_cmd640.c
+++ b/drivers/ata/pata_cmd640.c
@@ -181,10 +181,6 @@ static struct scsi_host_template cmd640_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations cmd640_port_ops = {
@@ -253,17 +249,16 @@ static void cmd640_hardware_init(struct pci_dev *pdev)
static int cmd640_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &cmd640_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.port_ops = &cmd640_port_ops
};
-
- static struct ata_port_info *port_info[2] = { &info, &info };
+ const struct ata_port_info *ppi[] = { &info, NULL };
cmd640_hardware_init(pdev);
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
static int cmd640_reinit_one(struct pci_dev *pdev)
diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c
index 3989cc5..2a79b33 100644
--- a/drivers/ata/pata_cmd64x.c
+++ b/drivers/ata/pata_cmd64x.c
@@ -266,10 +266,6 @@ static struct scsi_host_template cmd64x_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations cmd64x_port_ops = {
@@ -381,7 +377,7 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
u32 class_rev;
- static struct ata_port_info cmd_info[6] = {
+ static const struct ata_port_info cmd_info[6] = {
{ /* CMD 643 - no UDMA */
.sht = &cmd64x_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
@@ -428,11 +424,9 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &cmd648_port_ops
}
};
- static struct ata_port_info *port_info[2], *info;
+ const struct ata_port_info *ppi[] = { &cmd_info[id->driver_data], NULL };
u8 mrdmode;
- info = &cmd_info[id->driver_data];
-
pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class_rev);
class_rev &= 0xFF;
@@ -442,10 +436,10 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
if (pdev->device == PCI_DEVICE_ID_CMD_646) {
/* Does UDMA work ? */
if (class_rev > 4)
- info = &cmd_info[2];
+ ppi[0] = &cmd_info[2];
/* Early rev with other problems ? */
else if (class_rev == 1)
- info = &cmd_info[3];
+ ppi[0] = &cmd_info[3];
}
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 64);
@@ -461,8 +455,7 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
pci_write_config_byte(pdev, UDIDETCR0, 0xF0);
#endif
- port_info[0] = port_info[1] = info;
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c
index 79bef0d..83bcc5b 100644
--- a/drivers/ata/pata_cs5520.c
+++ b/drivers/ata/pata_cs5520.c
@@ -155,10 +155,6 @@ static struct scsi_host_template cs5520_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations cs5520_port_ops = {
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
index 29642d5..1b67923 100644
--- a/drivers/ata/pata_cs5530.c
+++ b/drivers/ata/pata_cs5530.c
@@ -176,10 +176,6 @@ static struct scsi_host_template cs5530_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations cs5530_port_ops = {
@@ -339,7 +335,7 @@ fail_put:
static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &cs5530_sht,
.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -348,23 +344,23 @@ static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &cs5530_port_ops
};
/* The docking connector doesn't do UDMA, and it seems not MWDMA */
- static struct ata_port_info info_palmax_secondary = {
+ static const struct ata_port_info info_palmax_secondary = {
.sht = &cs5530_sht,
.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
.pio_mask = 0x1f,
.port_ops = &cs5530_port_ops
};
- static struct ata_port_info *port_info[2] = { &info, &info };
+ const struct ata_port_info *ppi[] = { &info, NULL };
/* Chip initialisation */
if (cs5530_init_chip())
return -ENODEV;
if (cs5530_is_palmax())
- port_info[1] = &info_palmax_secondary;
+ ppi[1] = &info_palmax_secondary;
/* Now kick off ATA set up */
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_cs5535.c b/drivers/ata/pata_cs5535.c
index 22006ae..f37d4cd 100644
--- a/drivers/ata/pata_cs5535.c
+++ b/drivers/ata/pata_cs5535.c
@@ -173,10 +173,6 @@ static struct scsi_host_template cs5535_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations cs5535_port_ops = {
@@ -227,7 +223,7 @@ static struct ata_port_operations cs5535_port_ops = {
static int cs5535_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &cs5535_sht,
.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -235,7 +231,7 @@ static int cs5535_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.udma_mask = 0x1f,
.port_ops = &cs5535_port_ops
};
- struct ata_port_info *ports[1] = { &info };
+ const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
u32 timings, dummy;
@@ -247,7 +243,7 @@ static int cs5535_init_one(struct pci_dev *dev, const struct pci_device_id *id)
rdmsr(ATAC_CH0D1_PIO, timings, dummy);
if (CS5535_BAD_PIO(timings))
wrmsr(ATAC_CH0D1_PIO, 0xF7F4F7F4UL, 0);
- return ata_pci_init_one(dev, ports, 1);
+ return ata_pci_init_one(dev, ppi);
}
static const struct pci_device_id cs5535[] = {
diff --git a/drivers/ata/pata_cypress.c b/drivers/ata/pata_cypress.c
index 6ec049c..27b9f29 100644
--- a/drivers/ata/pata_cypress.c
+++ b/drivers/ata/pata_cypress.c
@@ -125,10 +125,6 @@ static struct scsi_host_template cy82c693_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations cy82c693_port_ops = {
@@ -169,14 +165,14 @@ static struct ata_port_operations cy82c693_port_ops = {
static int cy82c693_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &cy82c693_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &cy82c693_port_ops
};
- static struct ata_port_info *port_info[1] = { &info };
+ const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
/* Devfn 1 is the ATA primary. The secondary is magic and on devfn2.
For the moment we don't handle the secondary. FIXME */
@@ -184,7 +180,7 @@ static int cy82c693_init_one(struct pci_dev *pdev, const struct pci_device_id *i
if (PCI_FUNC(pdev->devfn) != 1)
return -ENODEV;
- return ata_pci_init_one(pdev, port_info, 1);
+ return ata_pci_init_one(pdev, ppi);
}
static const struct pci_device_id cy82c693[] = {
diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c
index d0f52e0..079248a 100644
--- a/drivers/ata/pata_efar.c
+++ b/drivers/ata/pata_efar.c
@@ -247,10 +247,6 @@ static struct scsi_host_template efar_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static const struct ata_port_operations efar_ops = {
@@ -305,7 +301,7 @@ static const struct ata_port_operations efar_ops = {
static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &efar_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
@@ -313,13 +309,13 @@ static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
.udma_mask = 0x0f, /* UDMA 66 */
.port_ops = &efar_ops,
};
- static struct ata_port_info *port_info[2] = { &info, &info };
+ const struct ata_port_info *ppi[] = { &info, NULL };
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
static const struct pci_device_id efar_pci_tbl[] = {
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index e64e05e..c6c8a8b 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -331,10 +331,6 @@ static struct scsi_host_template hpt36x_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
/*
@@ -421,7 +417,7 @@ static void hpt36x_init_chipset(struct pci_dev *dev)
static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct ata_port_info info_hpt366 = {
+ static const struct ata_port_info info_hpt366 = {
.sht = &hpt36x_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -429,7 +425,8 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.udma_mask = 0x1f,
.port_ops = &hpt366_port_ops
};
- struct ata_port_info *port_info[2] = {&info_hpt366, &info_hpt366};
+ struct ata_port_info info = info_hpt366;
+ const struct ata_port_info *ppi[] = { &info, NULL };
u32 class_rev;
u32 reg1;
@@ -450,17 +447,17 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
/* info_hpt366 is safe against re-entry so we can scribble on it */
switch((reg1 & 0x700) >> 8) {
case 5:
- info_hpt366.private_data = &hpt366_40;
+ info.private_data = &hpt366_40;
break;
case 9:
- info_hpt366.private_data = &hpt366_25;
+ info.private_data = &hpt366_25;
break;
default:
- info_hpt366.private_data = &hpt366_33;
+ info.private_data = &hpt366_33;
break;
}
/* Now kick off ATA set up */
- return ata_pci_init_one(dev, port_info, 2);
+ return ata_pci_init_one(dev, ppi);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index 1614e8c..5a0a410 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -887,7 +887,7 @@ static int hpt37x_calibrate_dpll(struct pci_dev *dev)
static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
/* HPT370 - UDMA100 */
- static struct ata_port_info info_hpt370 = {
+ static const struct ata_port_info info_hpt370 = {
.sht = &hpt37x_sht,
.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -896,7 +896,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.port_ops = &hpt370_port_ops
};
/* HPT370A - UDMA100 */
- static struct ata_port_info info_hpt370a = {
+ static const struct ata_port_info info_hpt370a = {
.sht = &hpt37x_sht,
.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -905,7 +905,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.port_ops = &hpt370a_port_ops
};
/* HPT370 - UDMA100 */
- static struct ata_port_info info_hpt370_33 = {
+ static const struct ata_port_info info_hpt370_33 = {
.sht = &hpt37x_sht,
.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -914,7 +914,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.port_ops = &hpt370_port_ops
};
/* HPT370A - UDMA100 */
- static struct ata_port_info info_hpt370a_33 = {
+ static const struct ata_port_info info_hpt370a_33 = {
.sht = &hpt37x_sht,
.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -923,7 +923,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.port_ops = &hpt370a_port_ops
};
/* HPT371, 372 and friends - UDMA133 */
- static struct ata_port_info info_hpt372 = {
+ static const struct ata_port_info info_hpt372 = {
.sht = &hpt37x_sht,
.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -932,7 +932,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.port_ops = &hpt372_port_ops
};
/* HPT371, 372 and friends - UDMA100 at 50MHz clock */
- static struct ata_port_info info_hpt372_50 = {
+ static const struct ata_port_info info_hpt372_50 = {
.sht = &hpt37x_sht,
.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -941,7 +941,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.port_ops = &hpt372_port_ops
};
/* HPT374 - UDMA133 */
- static struct ata_port_info info_hpt374 = {
+ static const struct ata_port_info info_hpt374 = {
.sht = &hpt37x_sht,
.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -951,9 +951,10 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
};
static const int MHz[4] = { 33, 40, 50, 66 };
-
- struct ata_port_info *port_info[2];
- struct ata_port_info *port;
+ const struct ata_port_info *port;
+ void *private_data = NULL;
+ struct ata_port_info port_info;
+ const struct ata_port_info *ppi[] = { &port_info, NULL };
u8 irqmask;
u32 class_rev;
@@ -1124,13 +1125,13 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
return -ENODEV;
}
if (clock_slot == 3)
- port->private_data = (void *)hpt37x_timings_66;
+ private_data = (void *)hpt37x_timings_66;
else
- port->private_data = (void *)hpt37x_timings_50;
+ private_data = (void *)hpt37x_timings_50;
printk(KERN_INFO "hpt37x: Bus clock %dMHz, using DPLL.\n", MHz[clock_slot]);
} else {
- port->private_data = (void *)chip_table->clocks[clock_slot];
+ private_data = (void *)chip_table->clocks[clock_slot];
/*
* Perform a final fixup. Note that we will have used the
* DPLL on the HPT372 which means we don't have to worry
@@ -1144,9 +1145,11 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
printk(KERN_INFO "hpt37x: %s: Bus clock %dMHz.\n", chip_table->name, MHz[clock_slot]);
}
- port_info[0] = port_info[1] = port;
/* Now kick off ATA set up */
- return ata_pci_init_one(dev, port_info, 2);
+ port_info = *port;
+ port_info.private_data = private_data;
+
+ return ata_pci_init_one(dev, ppi);
}
static const struct pci_device_id hpt37x[] = {
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index ea1037d..f25154a 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -488,7 +488,7 @@ static int hpt3x2n_pci_clock(struct pci_dev *pdev)
static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
/* HPT372N and friends - UDMA133 */
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &hpt3x2n_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -496,8 +496,8 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.udma_mask = 0x7f,
.port_ops = &hpt3x2n_port_ops
};
- struct ata_port_info *port_info[2];
- struct ata_port_info *port = &info;
+ struct ata_port_info port = info;
+ const struct ata_port_info *ppi[] = { &port, NULL };
u8 irqmask;
u32 class_rev;
@@ -585,9 +585,9 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
/* Set our private data up. We only need a few flags so we use
it directly */
- port->private_data = NULL;
+ port.private_data = NULL;
if (pci_mhz > 60) {
- port->private_data = (void *)PCI66;
+ port.private_data = (void *)PCI66;
/*
* On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
* the MISC. register to stretch the UltraDMA Tss timing.
@@ -598,8 +598,7 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
}
/* Now kick off ATA set up */
- port_info[0] = port_info[1] = port;
- return ata_pci_init_one(dev, port_info, 2);
+ return ata_pci_init_one(dev, ppi);
}
static const struct pci_device_id hpt3x2n[] = {
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
index ac28ec8..bbabe79 100644
--- a/drivers/ata/pata_hpt3x3.c
+++ b/drivers/ata/pata_hpt3x3.c
@@ -100,10 +100,6 @@ static struct scsi_host_template hpt3x3_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations hpt3x3_port_ops = {
@@ -175,7 +171,7 @@ static void hpt3x3_init_chipset(struct pci_dev *dev)
static int hpt3x3_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &hpt3x3_sht,
.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -183,11 +179,11 @@ static int hpt3x3_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.udma_mask = 0x07,
.port_ops = &hpt3x3_port_ops
};
- static struct ata_port_info *port_info[2] = { &info, &info };
+ const struct ata_port_info *ppi[] = { &info, NULL };
hpt3x3_init_chipset(dev);
/* Now kick off ATA set up */
- return ata_pci_init_one(dev, port_info, 2);
+ return ata_pci_init_one(dev, ppi);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_it8213.c b/drivers/ata/pata_it8213.c
index 17bf9f3..a769952 100644
--- a/drivers/ata/pata_it8213.c
+++ b/drivers/ata/pata_it8213.c
@@ -257,10 +257,6 @@ static struct scsi_host_template it8213_sht = {
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static const struct ata_port_operations it8213_ops = {
@@ -315,7 +311,7 @@ static const struct ata_port_operations it8213_ops = {
static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &it8213_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
@@ -323,14 +319,14 @@ static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *en
.udma_mask = 0x1f, /* UDMA 100 */
.port_ops = &it8213_ops,
};
- static struct ata_port_info *port_info[2] = { &info, &info };
+ /* Current IT8213 stuff is single port */
+ const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
- /* Current IT8213 stuff is single port */
- return ata_pci_init_one(pdev, port_info, 1);
+ return ata_pci_init_one(pdev, ppi);
}
static const struct pci_device_id it8213_pci_tbl[] = {
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
index f1f8cec..ff9a6fd 100644
--- a/drivers/ata/pata_it821x.c
+++ b/drivers/ata/pata_it821x.c
@@ -620,10 +620,6 @@ static struct scsi_host_template it821x_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations it821x_smart_port_ops = {
@@ -722,14 +718,14 @@ static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
u8 conf;
- static struct ata_port_info info_smart = {
+ static const struct ata_port_info info_smart = {
.sht = &it821x_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &it821x_smart_port_ops
};
- static struct ata_port_info info_passthru = {
+ static const struct ata_port_info info_passthru = {
.sht = &it821x_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -737,8 +733,8 @@ static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.udma_mask = 0x7f,
.port_ops = &it821x_passthru_port_ops
};
- static struct ata_port_info *port_info[2];
+ const struct ata_port_info *ppi[] = { NULL, NULL };
static char *mode[2] = { "pass through", "smart" };
/* Force the card into bypass mode if so requested */
@@ -751,11 +747,11 @@ static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
printk(KERN_INFO DRV_NAME ": controller in %s mode.\n", mode[conf]);
if (conf == 0)
- port_info[0] = port_info[1] = &info_passthru;
+ ppi[0] = &info_passthru;
else
- port_info[0] = port_info[1] = &info_smart;
+ ppi[0] = &info_smart;
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_ixp4xx_cf.c b/drivers/ata/pata_ixp4xx_cf.c
index 420c343..b994351 100644
--- a/drivers/ata/pata_ixp4xx_cf.c
+++ b/drivers/ata/pata_ixp4xx_cf.c
@@ -31,7 +31,7 @@ static int ixp4xx_set_mode(struct ata_port *ap, struct ata_device **error)
for (i = 0; i < ATA_MAX_DEVICES; i++) {
struct ata_device *dev = &ap->device[i];
- if (ata_dev_ready(dev)) {
+ if (ata_dev_enabled(dev)) {
ata_dev_printk(dev, KERN_INFO, "configured for PIO0\n");
dev->pio_mode = XFER_PIO_0;
dev->xfer_mode = XFER_PIO_0;
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
index 1daf78a..8d799e8 100644
--- a/drivers/ata/pata_jmicron.c
+++ b/drivers/ata/pata_jmicron.c
@@ -138,10 +138,6 @@ static struct scsi_host_template jmicron_sht = {
.slave_destroy = ata_scsi_slave_destroy,
/* Use standard CHS mapping rules */
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .suspend = ata_scsi_device_suspend,
- .resume = ata_scsi_device_resume,
-#endif
};
static const struct ata_port_operations jmicron_ops = {
@@ -195,7 +191,7 @@ static const struct ata_port_operations jmicron_ops = {
static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
{
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &jmicron_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
@@ -205,9 +201,9 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i
.port_ops = &jmicron_ops,
};
- struct ata_port_info *port_info[2] = { &info, &info };
+ const struct ata_port_info *ppi[] = { &info, NULL };
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
static const struct pci_device_id jmicron_pci_tbl[] = {
diff --git a/drivers/ata/pata_marvell.c b/drivers/ata/pata_marvell.c
index 837b7fe..edbfe0d 100644
--- a/drivers/ata/pata_marvell.c
+++ b/drivers/ata/pata_marvell.c
@@ -107,10 +107,6 @@ static struct scsi_host_template marvell_sht = {
.slave_destroy = ata_scsi_slave_destroy,
/* Use standard CHS mapping rules */
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static const struct ata_port_operations marvell_ops = {
@@ -165,7 +161,7 @@ static const struct ata_port_operations marvell_ops = {
static int marvell_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
{
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &marvell_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
@@ -175,7 +171,7 @@ static int marvell_init_one (struct pci_dev *pdev, const struct pci_device_id *i
.port_ops = &marvell_ops,
};
- static struct ata_port_info info_sata = {
+ static const struct ata_port_info info_sata = {
.sht = &marvell_sht,
/* Slave possible as its magically mapped not real */
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
@@ -186,13 +182,12 @@ static int marvell_init_one (struct pci_dev *pdev, const struct pci_device_id *i
.port_ops = &marvell_ops,
};
- struct ata_port_info *port_info[2] = { &info, &info_sata };
- int n_port = 2;
+ const struct ata_port_info *ppi[] = { &info, &info_sata };
if (pdev->device == 0x6101)
- n_port = 1;
+ ppi[1] = &ata_dummy_port_info;
- return ata_pci_init_one(pdev, port_info, n_port);
+ return ata_pci_init_one(pdev, ppi);
}
static const struct pci_device_id marvell_pci_tbl[] = {
diff --git a/drivers/ata/pata_mpc52xx.c b/drivers/ata/pata_mpc52xx.c
index 9587a89..368fac7 100644
--- a/drivers/ata/pata_mpc52xx.c
+++ b/drivers/ata/pata_mpc52xx.c
@@ -280,10 +280,6 @@ static struct scsi_host_template mpc52xx_ata_sht = {
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .suspend = ata_scsi_device_suspend,
- .resume = ata_scsi_device_resume,
-#endif
};
static struct ata_port_operations mpc52xx_ata_port_ops = {
diff --git a/drivers/ata/pata_mpiix.c b/drivers/ata/pata_mpiix.c
index 3bfbd49..4ea4283 100644
--- a/drivers/ata/pata_mpiix.c
+++ b/drivers/ata/pata_mpiix.c
@@ -165,10 +165,6 @@ static struct scsi_host_template mpiix_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations mpiix_port_ops = {
diff --git a/drivers/ata/pata_netcell.c b/drivers/ata/pata_netcell.c
index dbba5b7..81f5634 100644
--- a/drivers/ata/pata_netcell.c
+++ b/drivers/ata/pata_netcell.c
@@ -37,10 +37,6 @@ static struct scsi_host_template netcell_sht = {
.slave_destroy = ata_scsi_slave_destroy,
/* Use standard CHS mapping rules */
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static const struct ata_port_operations netcell_ops = {
@@ -96,7 +92,7 @@ static const struct ata_port_operations netcell_ops = {
static int netcell_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &netcell_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
/* Actually we don't really care about these as the
@@ -106,7 +102,7 @@ static int netcell_init_one (struct pci_dev *pdev, const struct pci_device_id *e
.udma_mask = 0x3f, /* UDMA 133 */
.port_ops = &netcell_ops,
};
- static struct ata_port_info *port_info[2] = { &info, &info };
+ const struct ata_port_info *port_info[] = { &info, NULL };
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev,
@@ -116,7 +112,7 @@ static int netcell_init_one (struct pci_dev *pdev, const struct pci_device_id *e
ata_pci_clear_simplex(pdev);
/* And let the library code do the work */
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, port_info);
}
static const struct pci_device_id netcell_pci_tbl[] = {
diff --git a/drivers/ata/pata_ns87410.c b/drivers/ata/pata_ns87410.c
index ebc58a9..ea70ec7 100644
--- a/drivers/ata/pata_ns87410.c
+++ b/drivers/ata/pata_ns87410.c
@@ -158,10 +158,6 @@ static struct scsi_host_template ns87410_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations ns87410_port_ops = {
@@ -195,14 +191,14 @@ static struct ata_port_operations ns87410_port_ops = {
static int ns87410_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &ns87410_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x0F,
.port_ops = &ns87410_port_ops
};
- static struct ata_port_info *port_info[2] = {&info, &info};
- return ata_pci_init_one(dev, port_info, 2);
+ const struct ata_port_info *ppi[] = { &info, NULL };
+ return ata_pci_init_one(dev, ppi);
}
static const struct pci_device_id ns87410[] = {
diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c
index 4d75d32..29c23dd 100644
--- a/drivers/ata/pata_oldpiix.c
+++ b/drivers/ata/pata_oldpiix.c
@@ -234,10 +234,6 @@ static struct scsi_host_template oldpiix_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static const struct ata_port_operations oldpiix_pata_ops = {
@@ -293,20 +289,20 @@ static const struct ata_port_operations oldpiix_pata_ops = {
static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &oldpiix_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma1-2 */
.port_ops = &oldpiix_pata_ops,
};
- static struct ata_port_info *port_info[2] = { &info, &info };
+ const struct ata_port_info *ppi[] = { &info, NULL };
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
static const struct pci_device_id oldpiix_pci_tbl[] = {
diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c
index 0af8a2c..1c44653 100644
--- a/drivers/ata/pata_opti.c
+++ b/drivers/ata/pata_opti.c
@@ -179,10 +179,6 @@ static struct scsi_host_template opti_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations opti_port_ops = {
@@ -220,19 +216,19 @@ static struct ata_port_operations opti_port_ops = {
static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &opti_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.port_ops = &opti_port_ops
};
- static struct ata_port_info *port_info[2] = { &info, &info };
+ const struct ata_port_info *ppi[] = { &info, NULL };
static int printed_version;
if (!printed_version++)
dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
- return ata_pci_init_one(dev, port_info, 2);
+ return ata_pci_init_one(dev, ppi);
}
static const struct pci_device_id opti[] = {
diff --git a/drivers/ata/pata_optidma.c b/drivers/ata/pata_optidma.c
index 2843e48..3093b02 100644
--- a/drivers/ata/pata_optidma.c
+++ b/drivers/ata/pata_optidma.c
@@ -363,10 +363,6 @@ static struct scsi_host_template optidma_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations optidma_port_ops = {
@@ -486,14 +482,14 @@ done_nomsg: /* Wrong chip revision */
static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct ata_port_info info_82c700 = {
+ static const struct ata_port_info info_82c700 = {
.sht = &optidma_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &optidma_port_ops
};
- static struct ata_port_info info_82c700_udma = {
+ static const struct ata_port_info info_82c700_udma = {
.sht = &optidma_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -501,8 +497,7 @@ static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.udma_mask = 0x07,
.port_ops = &optiplus_port_ops
};
- static struct ata_port_info *port_info[2];
- struct ata_port_info *info = &info_82c700;
+ const struct ata_port_info *ppi[] = { &info_82c700, NULL };
static int printed_version;
if (!printed_version++)
@@ -514,10 +509,9 @@ static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id)
pci_clock = inb(0x1F5) & 1; /* 0 = 33Mhz, 1 = 25Mhz */
if (optiplus_with_udma(dev))
- info = &info_82c700_udma;
+ ppi[0] = &info_82c700_udma;
- port_info[0] = port_info[1] = info;
- return ata_pci_init_one(dev, port_info, 2);
+ return ata_pci_init_one(dev, ppi);
}
static const struct pci_device_id optidma[] = {
diff --git a/drivers/ata/pata_pcmcia.c b/drivers/ata/pata_pcmcia.c
index 11245e3..4d44c75 100644
--- a/drivers/ata/pata_pcmcia.c
+++ b/drivers/ata/pata_pcmcia.c
@@ -397,6 +397,7 @@ static struct pcmcia_device_id pcmcia_devices[] = {
PCMCIA_DEVICE_PROD_ID12("TOSHIBA", "MK2001MPL", 0xb4585a1a, 0x3489e003),
PCMCIA_DEVICE_PROD_ID1("TRANSCEND 512M ", 0xd0909443),
PCMCIA_DEVICE_PROD_ID12("TRANSCEND", "TS1GCF80", 0x709b1bf1, 0x2a54d4b1),
+ PCMCIA_DEVICE_PROD_ID12("TRANSCEND", "TS2GCF120", 0x709b1bf1, 0x969aa4f2),
PCMCIA_DEVICE_PROD_ID12("TRANSCEND", "TS4GCF120", 0x709b1bf1, 0xf54a91c8),
PCMCIA_DEVICE_PROD_ID12("WIT", "IDE16", 0x244e5994, 0x3e232852),
PCMCIA_DEVICE_PROD_ID12("WEIDA", "TWTTI", 0xcc7cf69c, 0x212bb918),
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c
index ee636be..edbaf9d 100644
--- a/drivers/ata/pata_pdc202xx_old.c
+++ b/drivers/ata/pata_pdc202xx_old.c
@@ -244,10 +244,6 @@ static struct scsi_host_template pdc202xx_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations pdc2024x_port_ops = {
@@ -321,7 +317,7 @@ static struct ata_port_operations pdc2026x_port_ops = {
static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct ata_port_info info[3] = {
+ static const struct ata_port_info info[3] = {
{
.sht = &pdc202xx_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
@@ -348,9 +344,7 @@ static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id
}
};
- static struct ata_port_info *port_info[2];
-
- port_info[0] = port_info[1] = &info[id->driver_data];
+ const struct ata_port_info *ppi[] = { &info[id->driver_data], NULL };
if (dev->device == PCI_DEVICE_ID_PROMISE_20265) {
struct pci_dev *bridge = dev->bus->self;
@@ -362,7 +356,7 @@ static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id
return -ENODEV;
}
}
- return ata_pci_init_one(dev, port_info, 2);
+ return ata_pci_init_one(dev, ppi);
}
static const struct pci_device_id pdc202xx[] = {
diff --git a/drivers/ata/pata_platform.c b/drivers/ata/pata_platform.c
index a0a650c..1f63848 100644
--- a/drivers/ata/pata_platform.c
+++ b/drivers/ata/pata_platform.c
@@ -48,6 +48,8 @@ static int pata_platform_set_mode(struct ata_port *ap, struct ata_device **unuse
return 0;
}
+static int ata_dummy_ret0(struct ata_port *ap) { return 0; }
+
static struct scsi_host_template pata_platform_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
@@ -91,7 +93,7 @@ static struct ata_port_operations pata_platform_port_ops = {
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
- .port_start = ata_port_start,
+ .port_start = ata_dummy_ret0,
};
static void pata_platform_setup_port(struct ata_ioports *ioaddr,
diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c
index 1c54673..ba96b54 100644
--- a/drivers/ata/pata_radisys.c
+++ b/drivers/ata/pata_radisys.c
@@ -200,10 +200,6 @@ static struct scsi_host_template radisys_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static const struct ata_port_operations radisys_pata_ops = {
@@ -259,7 +255,7 @@ static const struct ata_port_operations radisys_pata_ops = {
static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &radisys_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
@@ -267,13 +263,13 @@ static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *e
.udma_mask = 0x14, /* UDMA33/66 only */
.port_ops = &radisys_pata_ops,
};
- static struct ata_port_info *port_info[2] = { &info, &info };
+ const struct ata_port_info *ppi[] = { &info, NULL };
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
static const struct pci_device_id radisys_pci_tbl[] = {
diff --git a/drivers/ata/pata_rz1000.c b/drivers/ata/pata_rz1000.c
index 85c4529..2bfd7ef 100644
--- a/drivers/ata/pata_rz1000.c
+++ b/drivers/ata/pata_rz1000.c
@@ -40,7 +40,7 @@ static int rz1000_set_mode(struct ata_port *ap, struct ata_device **unused)
for (i = 0; i < ATA_MAX_DEVICES; i++) {
struct ata_device *dev = &ap->device[i];
- if (ata_dev_ready(dev)) {
+ if (ata_dev_enabled(dev)) {
/* We don't really care */
dev->pio_mode = XFER_PIO_0;
dev->xfer_mode = XFER_PIO_0;
@@ -69,10 +69,6 @@ static struct scsi_host_template rz1000_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations rz1000_port_ops = {
@@ -135,22 +131,20 @@ static int rz1000_fifo_disable(struct pci_dev *pdev)
static int rz1000_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
- struct ata_port_info *port_info[2];
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &rz1000_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.port_ops = &rz1000_port_ops
};
+ const struct ata_port_info *ppi[] = { &info, NULL };
if (!printed_version++)
printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
- if (rz1000_fifo_disable(pdev) == 0) {
- port_info[0] = &info;
- port_info[1] = &info;
- return ata_pci_init_one(pdev, port_info, 2);
- }
+ if (rz1000_fifo_disable(pdev) == 0)
+ return ata_pci_init_one(pdev, ppi);
+
printk(KERN_ERR DRV_NAME ": failed to disable read-ahead on chipset..\n");
/* Not safe to use so skip */
return -ENODEV;
diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c
index 66e8ff4..225013e 100644
--- a/drivers/ata/pata_sc1200.c
+++ b/drivers/ata/pata_sc1200.c
@@ -194,10 +194,6 @@ static struct scsi_host_template sc1200_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations sc1200_port_ops = {
@@ -247,7 +243,7 @@ static struct ata_port_operations sc1200_port_ops = {
static int sc1200_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &sc1200_sht,
.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -255,10 +251,10 @@ static int sc1200_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.udma_mask = 0x07,
.port_ops = &sc1200_port_ops
};
- static struct ata_port_info *port_info[2] = { &info, &info };
-
/* Can't enable port 2 yet, see top comments */
- return ata_pci_init_one(dev, port_info, 1);
+ const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
+
+ return ata_pci_init_one(dev, ppi);
}
static const struct pci_device_id sc1200[] = {
diff --git a/drivers/ata/pata_scc.c b/drivers/ata/pata_scc.c
index 203f463..cca3aa2 100644
--- a/drivers/ata/pata_scc.c
+++ b/drivers/ata/pata_scc.c
@@ -984,10 +984,6 @@ static struct scsi_host_template scc_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static const struct ata_port_operations scc_pata_ops = {
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c
index b6e0203..dee6e21 100644
--- a/drivers/ata/pata_serverworks.c
+++ b/drivers/ata/pata_serverworks.c
@@ -315,10 +315,6 @@ static struct scsi_host_template serverworks_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations serverworks_osb4_port_ops = {
@@ -479,8 +475,7 @@ static void serverworks_fixup_ht1000(struct pci_dev *pdev)
static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
- int ports = 2;
- static struct ata_port_info info[4] = {
+ static const struct ata_port_info info[4] = {
{ /* OSB4 */
.sht = &serverworks_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
@@ -511,8 +506,7 @@ static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id
.port_ops = &serverworks_csb_port_ops
}
};
- static struct ata_port_info *port_info[2];
- struct ata_port_info *devinfo = &info[id->driver_data];
+ const struct ata_port_info *ppi[] = { &info[id->driver_data], NULL };
/* Force master latency timer to 64 PCI clocks */
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40);
@@ -521,7 +515,7 @@ static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id
if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
/* Select non UDMA capable OSB4 if we can't do fixups */
if ( serverworks_fixup_osb4(pdev) < 0)
- devinfo = &info[1];
+ ppi[0] = &info[1];
}
/* setup CSB5/CSB6 : South Bridge and IDE option RAID */
else if ((pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
@@ -531,11 +525,11 @@ static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id
/* If the returned btr is the newer revision then
select the right info block */
if (serverworks_fixup_csb(pdev) == 3)
- devinfo = &info[3];
+ ppi[0] = &info[3];
/* Is this the 3rd channel CSB6 IDE ? */
if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)
- ports = 1;
+ ppi[1] = &ata_dummy_port_info;
}
/* setup HT1000E */
else if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE)
@@ -544,8 +538,7 @@ static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id
if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
ata_pci_clear_simplex(pdev);
- port_info[0] = port_info[1] = devinfo;
- return ata_pci_init_one(pdev, port_info, ports);
+ return ata_pci_init_one(pdev, ppi);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index a5886f0..440e2cb 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -232,10 +232,6 @@ static struct scsi_host_template sil680_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .suspend = ata_scsi_device_suspend,
- .resume = ata_scsi_device_resume,
-#endif
};
static struct ata_port_operations sil680_port_ops = {
@@ -345,7 +341,7 @@ static u8 sil680_init_chip(struct pci_dev *pdev)
static int sil680_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &sil680_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -353,7 +349,7 @@ static int sil680_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.udma_mask = 0x7f,
.port_ops = &sil680_port_ops
};
- static struct ata_port_info info_slow = {
+ static const struct ata_port_info info_slow = {
.sht = &sil680_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
@@ -361,7 +357,7 @@ static int sil680_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.udma_mask = 0x3f,
.port_ops = &sil680_port_ops
};
- static struct ata_port_info *port_info[2] = {&info, &info};
+ const struct ata_port_info *ppi[] = { &info, NULL };
static int printed_version;
if (!printed_version++)
@@ -370,12 +366,12 @@ static int sil680_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
switch(sil680_init_chip(pdev))
{
case 0:
- port_info[0] = port_info[1] = &info_slow;
+ ppi[0] = &info_slow;
break;
case 0x30:
return -ENODEV;
}
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index f5838cc..f223126 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -38,8 +38,8 @@
#define DRV_VERSION "0.5.1"
struct sis_chipset {
- u16 device; /* PCI host ID */
- struct ata_port_info *info; /* Info block */
+ u16 device; /* PCI host ID */
+ const struct ata_port_info *info; /* Info block */
/* Probably add family, cable detect type etc here to clean
up code later */
};
@@ -524,10 +524,6 @@ static struct scsi_host_template sis_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static const struct ata_port_operations sis_133_ops = {
@@ -700,7 +696,7 @@ static const struct ata_port_operations sis_old_ops = {
.port_start = ata_port_start,
};
-static struct ata_port_info sis_info = {
+static const struct ata_port_info sis_info = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
@@ -708,7 +704,7 @@ static struct ata_port_info sis_info = {
.udma_mask = 0,
.port_ops = &sis_old_ops,
};
-static struct ata_port_info sis_info33 = {
+static const struct ata_port_info sis_info33 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
@@ -716,35 +712,35 @@ static struct ata_port_info sis_info33 = {
.udma_mask = ATA_UDMA2, /* UDMA 33 */
.port_ops = &sis_old_ops,
};
-static struct ata_port_info sis_info66 = {
+static const struct ata_port_info sis_info66 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA4, /* UDMA 66 */
.port_ops = &sis_66_ops,
};
-static struct ata_port_info sis_info100 = {
+static const struct ata_port_info sis_info100 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA5,
.port_ops = &sis_100_ops,
};
-static struct ata_port_info sis_info100_early = {
+static const struct ata_port_info sis_info100_early = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.udma_mask = ATA_UDMA5,
.pio_mask = 0x1f, /* pio0-4 */
.port_ops = &sis_66_ops,
};
-struct ata_port_info sis_info133 = {
+const struct ata_port_info sis_info133 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &sis_133_ops,
};
-static struct ata_port_info sis_info133_early = {
+static const struct ata_port_info sis_info133_early = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
@@ -827,8 +823,8 @@ static void sis_fixup(struct pci_dev *pdev, struct sis_chipset *sis)
static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
- static struct ata_port_info *port_info[2];
- struct ata_port_info *port;
+ struct ata_port_info port;
+ const struct ata_port_info *ppi[] = { &port, NULL };
struct pci_dev *host = NULL;
struct sis_chipset *chipset = NULL;
struct sis_chipset *sets;
@@ -968,13 +964,12 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
if (chipset == NULL)
return -ENODEV;
- port = chipset->info;
- port->private_data = chipset;
+ port = *chipset->info;
+ port.private_data = chipset;
sis_fixup(pdev, chipset);
- port_info[0] = port_info[1] = port;
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
static const struct pci_device_id sis_pci_tbl[] = {
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index 9aeffdb..f48491a 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -301,20 +301,22 @@ static int sl82c105_bridge_revision(struct pci_dev *pdev)
static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct ata_port_info info_dma = {
+ static const struct ata_port_info info_dma = {
.sht = &sl82c105_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &sl82c105_port_ops
};
- static struct ata_port_info info_early = {
+ static const struct ata_port_info info_early = {
.sht = &sl82c105_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.port_ops = &sl82c105_port_ops
};
- static struct ata_port_info *port_info[2] = { &info_early, &info_early };
+ /* for now use only the first port */
+ const struct ata_port_info *ppi[] = { &info_early,
+ &ata_dummy_port_info };
u32 val;
int rev;
@@ -324,17 +326,14 @@ static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id
dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Unable to find bridge, disabling DMA.\n");
else if (rev <= 5)
dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Early bridge revision, no DMA available.\n");
- else {
- port_info[0] = &info_dma;
- port_info[1] = &info_dma;
- }
+ else
+ ppi[0] = &info_dma;
pci_read_config_dword(dev, 0x40, &val);
val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
pci_write_config_dword(dev, 0x40, val);
-
- return ata_pci_init_one(dev, port_info, 1); /* For now */
+ return ata_pci_init_one(dev, ppi);
}
static const struct pci_device_id sl82c105[] = {
diff --git a/drivers/ata/pata_triflex.c b/drivers/ata/pata_triflex.c
index 349887b..b1d3076 100644
--- a/drivers/ata/pata_triflex.c
+++ b/drivers/ata/pata_triflex.c
@@ -194,10 +194,6 @@ static struct scsi_host_template triflex_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations triflex_port_ops = {
@@ -237,20 +233,20 @@ static struct ata_port_operations triflex_port_ops = {
static int triflex_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct ata_port_info info = {
+ static const struct ata_port_info info = {
.sht = &triflex_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &triflex_port_ops
};
- static struct ata_port_info *port_info[2] = { &info, &info };
+ const struct ata_port_info *ppi[] = { &info, NULL };
static int printed_version;
if (!printed_version++)
dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
- return ata_pci_init_one(dev, port_info, 2);
+ return ata_pci_init_one(dev, ppi);
}
static const struct pci_device_id triflex[] = {
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 362beb2..e4c71f7 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -301,10 +301,6 @@ static struct scsi_host_template via_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations via_port_ops = {
@@ -425,7 +421,7 @@ static void via_config_fifo(struct pci_dev *pdev, unsigned int flags)
static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
/* Early VIA without UDMA support */
- static struct ata_port_info via_mwdma_info = {
+ static const struct ata_port_info via_mwdma_info = {
.sht = &via_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
.pio_mask = 0x1f,
@@ -433,7 +429,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &via_port_ops
};
/* Ditto with IRQ masking required */
- static struct ata_port_info via_mwdma_info_borked = {
+ static const struct ata_port_info via_mwdma_info_borked = {
.sht = &via_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
.pio_mask = 0x1f,
@@ -441,7 +437,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &via_port_ops_noirq,
};
/* VIA UDMA 33 devices (and borked 66) */
- static struct ata_port_info via_udma33_info = {
+ static const struct ata_port_info via_udma33_info = {
.sht = &via_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
.pio_mask = 0x1f,
@@ -450,7 +446,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &via_port_ops
};
/* VIA UDMA 66 devices */
- static struct ata_port_info via_udma66_info = {
+ static const struct ata_port_info via_udma66_info = {
.sht = &via_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
.pio_mask = 0x1f,
@@ -459,7 +455,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &via_port_ops
};
/* VIA UDMA 100 devices */
- static struct ata_port_info via_udma100_info = {
+ static const struct ata_port_info via_udma100_info = {
.sht = &via_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
.pio_mask = 0x1f,
@@ -468,7 +464,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &via_port_ops
};
/* UDMA133 with bad AST (All current 133) */
- static struct ata_port_info via_udma133_info = {
+ static const struct ata_port_info via_udma133_info = {
.sht = &via_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
.pio_mask = 0x1f,
@@ -476,7 +472,8 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.udma_mask = 0x7f, /* FIXME: should check north bridge */
.port_ops = &via_port_ops
};
- struct ata_port_info *port_info[2], *type;
+ struct ata_port_info type;
+ const struct ata_port_info *ppi[] = { &type, NULL };
struct pci_dev *isa = NULL;
const struct via_isa_bridge *config;
static int printed_version;
@@ -521,25 +518,25 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
switch(config->flags & VIA_UDMA) {
case VIA_UDMA_NONE:
if (config->flags & VIA_NO_UNMASK)
- type = &via_mwdma_info_borked;
+ type = via_mwdma_info_borked;
else
- type = &via_mwdma_info;
+ type = via_mwdma_info;
break;
case VIA_UDMA_33:
- type = &via_udma33_info;
+ type = via_udma33_info;
break;
case VIA_UDMA_66:
- type = &via_udma66_info;
+ type = via_udma66_info;
/* The 66 MHz devices require we enable the clock */
pci_read_config_dword(pdev, 0x50, &timing);
timing |= 0x80008;
pci_write_config_dword(pdev, 0x50, timing);
break;
case VIA_UDMA_100:
- type = &via_udma100_info;
+ type = via_udma100_info;
break;
case VIA_UDMA_133:
- type = &via_udma133_info;
+ type = via_udma133_info;
break;
default:
WARN_ON(1);
@@ -554,10 +551,9 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
}
/* We have established the device type, now fire it up */
- type->private_data = (void *)config;
+ type.private_data = (void *)config;
- port_info[0] = port_info[1] = type;
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
#ifdef CONFIG_PM
diff --git a/drivers/ata/sata_inic162x.c b/drivers/ata/sata_inic162x.c
index b3b62e9..bda5e77 100644
--- a/drivers/ata/sata_inic162x.c
+++ b/drivers/ata/sata_inic162x.c
@@ -135,10 +135,6 @@ static struct scsi_host_template inic_sht = {
.slave_configure = inic_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .suspend = ata_scsi_device_suspend,
- .resume = ata_scsi_device_resume,
-#endif
};
static const int scr_map[] = {
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index a097595..4cea3ef 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -325,10 +325,6 @@ static struct scsi_host_template nv_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .suspend = ata_scsi_device_suspend,
- .resume = ata_scsi_device_resume,
-#endif
};
static struct scsi_host_template nv_adma_sht = {
@@ -347,10 +343,6 @@ static struct scsi_host_template nv_adma_sht = {
.slave_configure = nv_adma_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .suspend = ata_scsi_device_suspend,
- .resume = ata_scsi_device_resume,
-#endif
};
static const struct ata_port_operations nv_generic_ops = {
@@ -465,7 +457,7 @@ static const struct ata_port_operations nv_adma_ops = {
.host_stop = nv_adma_host_stop,
};
-static struct ata_port_info nv_port_info[] = {
+static const struct ata_port_info nv_port_info[] = {
/* generic */
{
.sht = &nv_sht,
@@ -1545,7 +1537,7 @@ static void nv_adma_error_handler(struct ata_port *ap)
static int nv_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version = 0;
- const struct ata_port_info *ppi[2];
+ const struct ata_port_info *ppi[] = { NULL, NULL };
struct ata_host *host;
struct nv_host_priv *hpriv;
int rc;
@@ -1573,8 +1565,8 @@ static int nv_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
type = ADMA;
}
- ppi[0] = ppi[1] = &nv_port_info[type];
- rc = ata_pci_prepare_native_host(pdev, ppi, 2, &host);
+ ppi[0] = &nv_port_info[type];
+ rc = ata_pci_prepare_native_host(pdev, ppi, &host);
if (rc)
return rc;
diff --git a/drivers/ata/sata_sil.c b/drivers/ata/sata_sil.c
index 0a1e417..e8483aa 100644
--- a/drivers/ata/sata_sil.c
+++ b/drivers/ata/sata_sil.c
@@ -182,10 +182,6 @@ static struct scsi_host_template sil_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .suspend = ata_scsi_device_suspend,
- .resume = ata_scsi_device_resume,
-#endif
};
static const struct ata_port_operations sil_ops = {
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index b97ee9f..a69d78c 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -380,10 +380,6 @@ static struct scsi_host_template sil24_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .suspend = ata_scsi_device_suspend,
- .resume = ata_scsi_device_resume,
-#endif
};
static const struct ata_port_operations sil24_ops = {
diff --git a/drivers/ata/sata_sis.c b/drivers/ata/sata_sis.c
index d8ee062..ee66c5f 100644
--- a/drivers/ata/sata_sis.c
+++ b/drivers/ata/sata_sis.c
@@ -129,7 +129,7 @@ static const struct ata_port_operations sis_ops = {
.port_start = ata_port_start,
};
-static struct ata_port_info sis_port_info = {
+static const struct ata_port_info sis_port_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
.pio_mask = 0x1f,
.mwdma_mask = 0x7,
@@ -255,7 +255,7 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
struct ata_port_info pi = sis_port_info;
- const struct ata_port_info *ppi[2] = { &pi, &pi };
+ const struct ata_port_info *ppi[] = { &pi, NULL };
struct ata_host *host;
u32 genctl, val;
u8 pmr;
@@ -335,7 +335,7 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
break;
}
- rc = ata_pci_prepare_native_host(pdev, ppi, 2, &host);
+ rc = ata_pci_prepare_native_host(pdev, ppi, &host);
if (rc)
return rc;
diff --git a/drivers/ata/sata_uli.c b/drivers/ata/sata_uli.c
index f74e383..006f5e3 100644
--- a/drivers/ata/sata_uli.c
+++ b/drivers/ata/sata_uli.c
@@ -125,7 +125,7 @@ static const struct ata_port_operations uli_ops = {
.port_start = ata_port_start,
};
-static struct ata_port_info uli_port_info = {
+static const struct ata_port_info uli_port_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_IGN_SIMPLEX,
.pio_mask = 0x1f, /* pio0-4 */
@@ -201,19 +201,33 @@ static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
n_ports = 2;
if (board_idx == uli_5287)
n_ports = 4;
- rc = ata_pci_prepare_native_host(pdev, ppi, n_ports, &host);
- if (rc)
- return rc;
+
+ /* allocate the host */
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports);
+ if (!host)
+ return -ENOMEM;
hpriv = devm_kzalloc(&pdev->dev, sizeof(*hpriv), GFP_KERNEL);
if (!hpriv)
return -ENOMEM;
host->private_data = hpriv;
+ /* the first two ports are standard SFF */
+ rc = ata_pci_init_native_host(host);
+ if (rc)
+ return rc;
+
+ rc = ata_pci_init_bmdma(host);
+ if (rc)
+ return rc;
+
iomap = host->iomap;
switch (board_idx) {
case uli_5287:
+ /* If there are four, the last two live right after
+ * the standard SFF ports.
+ */
hpriv->scr_cfg_addr[0] = ULI5287_BASE;
hpriv->scr_cfg_addr[1] = ULI5287_BASE + ULI5287_OFFS;
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index 939c924..d105d2c 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -116,10 +116,6 @@ static struct scsi_host_template svia_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .suspend = ata_scsi_device_suspend,
- .resume = ata_scsi_device_resume,
-#endif
};
static const struct ata_port_operations vt6420_sata_ops = {
@@ -415,7 +411,7 @@ static int vt6420_prepare_host(struct pci_dev *pdev, struct ata_host **r_host)
struct ata_host *host;
int rc;
- rc = ata_pci_prepare_native_host(pdev, ppi, 2, &host);
+ rc = ata_pci_prepare_native_host(pdev, ppi, &host);
if (rc)
return rc;
*r_host = host;
diff --git a/drivers/ata/sis.h b/drivers/ata/sis.h
index 231da8f..0f2208d 100644
--- a/drivers/ata/sis.h
+++ b/drivers/ata/sis.h
@@ -2,4 +2,4 @@
struct ata_port_info;
/* pata_sis.c */
-extern struct ata_port_info sis_info133;
+extern const struct ata_port_info sis_info133;
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index 147d86f..6ccc2e9 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -875,6 +875,7 @@ static void __devinit quirk_sb600_sata(struct pci_dev *pdev)
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_sb600_sata);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_sb600_sata);
/*
* Serverworks CSB5 IDE does not fully support native mode
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 7906d75..27d9362 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -140,7 +140,6 @@ enum {
ATA_DFLAG_PIO = (1 << 8), /* device limited to PIO mode */
ATA_DFLAG_NCQ_OFF = (1 << 9), /* device limited to non-NCQ mode */
- ATA_DFLAG_SUSPENDED = (1 << 10), /* device suspended */
ATA_DFLAG_INIT_MASK = (1 << 16) - 1,
ATA_DFLAG_DETACH = (1 << 16),
@@ -191,6 +190,7 @@ enum {
ATA_PFLAG_LOADING = (1 << 4), /* boot/loading probe */
ATA_PFLAG_UNLOADING = (1 << 5), /* module is unloading */
ATA_PFLAG_SCSI_HOTPLUG = (1 << 6), /* SCSI hotplug scheduled */
+ ATA_PFLAG_INITIALIZING = (1 << 7), /* being initialized, don't touch */
ATA_PFLAG_FLUSH_PORT_TASK = (1 << 16), /* flush port task */
ATA_PFLAG_SUSPENDED = (1 << 17), /* port is suspended (power) */
@@ -254,10 +254,6 @@ enum {
ATA_DMA_PAD_SZ = 4,
ATA_DMA_PAD_BUF_SZ = ATA_DMA_PAD_SZ * ATA_MAX_QUEUE,
- /* masks for port functions */
- ATA_PORT_PRIMARY = (1 << 0),
- ATA_PORT_SECONDARY = (1 << 1),
-
/* ering size */
ATA_ERING_SIZE = 32,
@@ -268,13 +264,9 @@ enum {
ATA_EH_REVALIDATE = (1 << 0),
ATA_EH_SOFTRESET = (1 << 1),
ATA_EH_HARDRESET = (1 << 2),
- ATA_EH_SUSPEND = (1 << 3),
- ATA_EH_RESUME = (1 << 4),
- ATA_EH_PM_FREEZE = (1 << 5),
ATA_EH_RESET_MASK = ATA_EH_SOFTRESET | ATA_EH_HARDRESET,
- ATA_EH_PERDEV_MASK = ATA_EH_REVALIDATE | ATA_EH_SUSPEND |
- ATA_EH_RESUME | ATA_EH_PM_FREEZE,
+ ATA_EH_PERDEV_MASK = ATA_EH_REVALIDATE,
/* ata_eh_info->flags */
ATA_EHI_HOTPLUGGED = (1 << 0), /* could have been hotplugged */
@@ -466,7 +458,7 @@ struct ata_device {
struct ata_ering ering;
int spdn_cnt;
unsigned int horkage; /* List of broken features */
-#ifdef CONFIG_SATA_ACPI
+#ifdef CONFIG_ATA_ACPI
/* ACPI objects info */
acpi_handle obj_handle;
#endif
@@ -693,8 +685,8 @@ extern void ata_std_postreset(struct ata_port *ap, unsigned int *classes);
extern void ata_port_disable(struct ata_port *);
extern void ata_std_ports(struct ata_ioports *ioaddr);
#ifdef CONFIG_PCI
-extern int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
- unsigned int n_ports);
+extern int ata_pci_init_one (struct pci_dev *pdev,
+ const struct ata_port_info * const * ppi);
extern void ata_pci_remove_one (struct pci_dev *pdev);
#ifdef CONFIG_PM
extern void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t mesg);
@@ -736,8 +728,6 @@ extern int sata_scr_write_flush(struct ata_port *ap, int reg, u32 val);
extern int ata_port_online(struct ata_port *ap);
extern int ata_port_offline(struct ata_port *ap);
#ifdef CONFIG_PM
-extern int ata_scsi_device_resume(struct scsi_device *);
-extern int ata_scsi_device_suspend(struct scsi_device *, pm_message_t mesg);
extern int ata_host_suspend(struct ata_host *host, pm_message_t mesg);
extern void ata_host_resume(struct ata_host *host);
#endif
@@ -861,11 +851,11 @@ struct pci_bits {
unsigned long val;
};
-extern int ata_pci_init_native_host(struct ata_host *host,
- unsigned int port_mask);
+extern int ata_pci_init_native_host(struct ata_host *host);
+extern int ata_pci_init_bmdma(struct ata_host *host);
extern int ata_pci_prepare_native_host(struct pci_dev *pdev,
const struct ata_port_info * const * ppi,
- int n_ports, struct ata_host **r_host);
+ struct ata_host **r_host);
extern int pci_test_config_bits(struct pci_dev *pdev, const struct pci_bits *bits);
extern unsigned long ata_pci_default_filter(struct ata_device *, unsigned long);
#endif /* CONFIG_PCI */
@@ -1008,11 +998,6 @@ static inline unsigned int ata_dev_absent(const struct ata_device *dev)
return ata_class_absent(dev->class);
}
-static inline unsigned int ata_dev_ready(const struct ata_device *dev)
-{
- return ata_dev_enabled(dev) && !(dev->flags & ATA_DFLAG_SUSPENDED);
-}
-
/*
* port helpers
*/
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index ae849f0..ccd85e4 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -370,6 +370,7 @@
#define PCI_DEVICE_ID_ATI_IXP600_SATA 0x4380
#define PCI_DEVICE_ID_ATI_IXP600_SMBUS 0x4385
#define PCI_DEVICE_ID_ATI_IXP600_IDE 0x438c
+#define PCI_DEVICE_ID_ATI_IXP700_SATA 0x4390
#define PCI_VENDOR_ID_VLSI 0x1004
#define PCI_DEVICE_ID_VLSI_82C592 0x0005
^ permalink raw reply related [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-05-01 21:34 ` Jesse Barnes
@ 2007-05-10 0:18 ` Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2007-05-10 0:18 UTC (permalink / raw)
To: Jesse Barnes; +Cc: linux-ide, LKML
Jesse Barnes wrote:
> On Sunday, April 29, 2007 9:15 am Jeff Garzik wrote:
>> Noteworthy changes:
>> * remove combined mode PCI quirk. IDE driver selection (libata or
>> old-IDE) is now determined purely by module load order.
>> * new driver API, that is far more like other kernel APIs:
>> alloc...register...unregister...free.
>> * More Alan PATA work
>> * Lots of other little bits.
>
>> drivers/pci/quirks.c | 113 ----
>
> Looks like you removed the combined_mode quirk (yay!) but didn't update
> kernel-parameters.txt... might confuse people. Here's a patch to remove
> mention of it from the documentation.
>
> Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
>
> Thanks,
> Jesse
>
> diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
> index 84c3bd0..49b1ea3 100644
> --- a/Documentation/kernel-parameters.txt
> +++ b/Documentation/kernel-parameters.txt
> @@ -722,14 +722,6 @@ and is between 256 and 4096 characters. It is defined in the file
> inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver
> Format: <irq>
>
> - combined_mode= [HW] control which driver uses IDE ports in combined
> - mode: legacy IDE driver, libata, or both
> - (in the libata case, libata.atapi_enabled=1 may be
> - useful as well). Note that using the ide or libata
> - options may affect your device naming (e.g. by
> - changing hdc to sdb).
> - Format: combined (default), ide, or libata
> -
applied
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-05-01 22:49 ` Chuck Ebbert
@ 2007-05-02 0:48 ` Stephen Clark
0 siblings, 0 replies; 95+ messages in thread
From: Stephen Clark @ 2007-05-02 0:48 UTC (permalink / raw)
To: Chuck Ebbert; +Cc: Jesse Barnes, Jeff Garzik, linux-ide, LKML
Chuck Ebbert wrote:
>Stephen Clark wrote:
>
>
>>I'm running fc6 but with kernel 2.6.21 from kernel.org - compiled with
>>the .config file from fc6.
>>
>>My system is a asus laptop with an ich7 chipset which has both sata and
>>pata controllers. My
>>laptop only brings out the pata controller interface and both my hd and
>>od are on the second
>>channel of the pata.
>>
>>So can I configure out the old ide and just have ata_piix automatically
>>control them both in
>>2.6.21?
>>
>>
>>
>
>Sure, just edit the .config. You may need to play with options to mkinitrd
>though; I don't think it will include the PATA drivers for you automatically.
>
>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at http://vger.kernel.org/majordomo-info.html
>Please read the FAQ at http://www.tux.org/lkml/
>
>
>
It worked - no combined_mode=libata and my hd is doing 45mb/sec.
Thanks to all who replied.
Steve
--
"They that give up essential liberty to obtain temporary safety,
deserve neither liberty nor safety." (Ben Franklin)
"The course of history shows that as a government grows, liberty
decreases." (Thomas Jefferson)
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-05-01 22:45 ` Stephen Clark
2007-05-01 22:49 ` Jesse Barnes
@ 2007-05-01 22:49 ` Chuck Ebbert
2007-05-02 0:48 ` Stephen Clark
1 sibling, 1 reply; 95+ messages in thread
From: Chuck Ebbert @ 2007-05-01 22:49 UTC (permalink / raw)
To: Stephen.Clark; +Cc: Jesse Barnes, Jeff Garzik, linux-ide, LKML
Stephen Clark wrote:
>>
> I'm running fc6 but with kernel 2.6.21 from kernel.org - compiled with
> the .config file from fc6.
>
> My system is a asus laptop with an ich7 chipset which has both sata and
> pata controllers. My
> laptop only brings out the pata controller interface and both my hd and
> od are on the second
> channel of the pata.
>
> So can I configure out the old ide and just have ata_piix automatically
> control them both in
> 2.6.21?
>
Sure, just edit the .config. You may need to play with options to mkinitrd
though; I don't think it will include the PATA drivers for you automatically.
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-05-01 22:45 ` Stephen Clark
@ 2007-05-01 22:49 ` Jesse Barnes
2007-05-01 22:49 ` Chuck Ebbert
1 sibling, 0 replies; 95+ messages in thread
From: Jesse Barnes @ 2007-05-01 22:49 UTC (permalink / raw)
To: Stephen.Clark; +Cc: Jeff Garzik, Chuck Ebbert, linux-ide, LKML
On Tuesday, May 1, 2007 3:45 pm Stephen Clark wrote:
> I'm running fc6 but with kernel 2.6.21 from kernel.org - compiled
> with the .config file from fc6.
>
> My system is a asus laptop with an ich7 chipset which has both sata
> and pata controllers. My
> laptop only brings out the pata controller interface and both my hd
> and od are on the second
> channel of the pata.
>
> So can I configure out the old ide and just have ata_piix
> automatically control them both in
> 2.6.21?
Yeah, I think that'll work. You could try an FC7 .config file if that's
easier.
Jesse
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-05-01 21:38 ` Jesse Barnes
@ 2007-05-01 22:45 ` Stephen Clark
2007-05-01 22:49 ` Jesse Barnes
2007-05-01 22:49 ` Chuck Ebbert
0 siblings, 2 replies; 95+ messages in thread
From: Stephen Clark @ 2007-05-01 22:45 UTC (permalink / raw)
To: Jesse Barnes; +Cc: Jeff Garzik, Chuck Ebbert, linux-ide, LKML
Jesse Barnes wrote:
>On Monday, April 30, 2007 1:22 pm Stephen Clark wrote:
>
>
>>Please don't do this!
>>
>>Yeah the kernel will boot but the hd performance is sh*t on my
>>laptop. I am running FC6 with
>>kernel 2.6.21 and without the combined_mode setting my disk
>>performance goes down to a
>>whopping 1.25mb/sec from 44mb/sec when I boot with
>>combined_mode=libata. It make my
>>system unusable!
>>
>>
>
>So your performance is good when you add combined_mode=libata? I hope
>so, because that's why I added it in the first place...
>
>However, Jeff's patch won't steal your performance as long as you make
>sure you use the libata based drivers for everything. If you're
>running Fedora I think the rawhide kernels are configured this way, but
>the fc6 era kernels aren't.
>
>Jesse
>
>
>
I'm running fc6 but with kernel 2.6.21 from kernel.org - compiled with
the .config file from fc6.
My system is a asus laptop with an ich7 chipset which has both sata and
pata controllers. My
laptop only brings out the pata controller interface and both my hd and
od are on the second
channel of the pata.
So can I configure out the old ide and just have ata_piix automatically
control them both in
2.6.21?
Thanks,
Steve
--
"They that give up essential liberty to obtain temporary safety,
deserve neither liberty nor safety." (Ben Franklin)
"The course of history shows that as a government grows, liberty
decreases." (Thomas Jefferson)
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-04-30 20:22 ` Stephen Clark
2007-04-30 20:31 ` Alan Cox
2007-04-30 20:31 ` Jeff Garzik
@ 2007-05-01 21:38 ` Jesse Barnes
2007-05-01 22:45 ` Stephen Clark
2 siblings, 1 reply; 95+ messages in thread
From: Jesse Barnes @ 2007-05-01 21:38 UTC (permalink / raw)
To: Stephen.Clark; +Cc: Jeff Garzik, Chuck Ebbert, linux-ide, LKML
On Monday, April 30, 2007 1:22 pm Stephen Clark wrote:
> Please don't do this!
>
> Yeah the kernel will boot but the hd performance is sh*t on my
> laptop. I am running FC6 with
> kernel 2.6.21 and without the combined_mode setting my disk
> performance goes down to a
> whopping 1.25mb/sec from 44mb/sec when I boot with
> combined_mode=libata. It make my
> system unusable!
So your performance is good when you add combined_mode=libata? I hope
so, because that's why I added it in the first place...
However, Jeff's patch won't steal your performance as long as you make
sure you use the libata based drivers for everything. If you're
running Fedora I think the rawhide kernels are configured this way, but
the fc6 era kernels aren't.
Jesse
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-04-29 16:15 Jeff Garzik
2007-04-30 19:52 ` Chuck Ebbert
@ 2007-05-01 21:34 ` Jesse Barnes
2007-05-10 0:18 ` Jeff Garzik
1 sibling, 1 reply; 95+ messages in thread
From: Jesse Barnes @ 2007-05-01 21:34 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-ide, LKML
On Sunday, April 29, 2007 9:15 am Jeff Garzik wrote:
> Noteworthy changes:
> * remove combined mode PCI quirk. IDE driver selection (libata or
> old-IDE) is now determined purely by module load order.
> * new driver API, that is far more like other kernel APIs:
> alloc...register...unregister...free.
> * More Alan PATA work
> * Lots of other little bits.
> drivers/pci/quirks.c | 113 ----
Looks like you removed the combined_mode quirk (yay!) but didn't update
kernel-parameters.txt... might confuse people. Here's a patch to remove
mention of it from the documentation.
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Thanks,
Jesse
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 84c3bd0..49b1ea3 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -722,14 +722,6 @@ and is between 256 and 4096 characters. It is defined in the file
inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver
Format: <irq>
- combined_mode= [HW] control which driver uses IDE ports in combined
- mode: legacy IDE driver, libata, or both
- (in the libata case, libata.atapi_enabled=1 may be
- useful as well). Note that using the ide or libata
- options may affect your device naming (e.g. by
- changing hdc to sdb).
- Format: combined (default), ide, or libata
-
inttest= [IA64]
io7= [HW] IO7 for Marvel based alpha systems
^ permalink raw reply related [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-04-30 20:31 ` Jeff Garzik
@ 2007-05-01 11:55 ` Stephen Clark
0 siblings, 0 replies; 95+ messages in thread
From: Stephen Clark @ 2007-05-01 11:55 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Chuck Ebbert, linux-ide, LKML
Jeff Garzik wrote:
>Stephen Clark wrote:
>
>
>>Yeah the kernel will boot but the hd performance is sh*t on my laptop. I
>>am running FC6 with
>>kernel 2.6.21 and without the combined_mode setting my disk performance
>>goes down to a
>>whopping 1.25mb/sec from 44mb/sec when I boot with combined_mode=libata.
>>It make my
>>system unusable!
>>
>>
>
>
>No, that's the split-driver configuration that causes the slowdown.
>
>Now that both drivers fully support the hardware, either driver can make
>things go full speed.
>
>Please try testing the update first :)
>
> Jeff
>
>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at http://vger.kernel.org/majordomo-info.html
>Please read the FAQ at http://www.tux.org/lkml/
>
>
>
Ok, I'am willing to test it out, but how to I get a patch file from the
git stuff?
I currently have the 2.6.21 kernel source.
Steve
--
"They that give up essential liberty to obtain temporary safety,
deserve neither liberty nor safety." (Ben Franklin)
"The course of history shows that as a government grows, liberty
decreases." (Thomas Jefferson)
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-04-30 22:06 ` Chuck Ebbert
@ 2007-04-30 22:11 ` Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2007-04-30 22:11 UTC (permalink / raw)
To: Chuck Ebbert; +Cc: linux-ide, LKML
Chuck Ebbert wrote:
> Jeff Garzik wrote:
>> Chuck Ebbert wrote:
>>> Jeff Garzik wrote:
>>>> Jeff Garzik (8):
>>>> libata/IDE: remove combined mode quirk
>>> You can't just remove the "combined_mode=" kernel parameter or
>>> every Linux user who uses that will get an unbootable kernel
>>> with no good way of diagnosing the problem. It should still
>>> be accepted and just print a warning.
>> No, most modern distros will simply Just Work(tm) due to mount by label,
>> udev, and similar gadgets.
>>
>> As long as you have at least one (if not both) ATA drivers, you have a
>> kernel that will boot your hardware. And by definition those using
>> combined_mode= do indeed have the necessary drivers.
>
> OK, this is a kernel parameter and should be fine. But you can't remove
> *module* parameters for drivers needed for booting or the initrd will
> fail to load the module with "unknown parameter" and users can't boot.
No module parameters were removed.
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-04-30 20:05 ` Jeff Garzik
2007-04-30 20:22 ` Stephen Clark
@ 2007-04-30 22:06 ` Chuck Ebbert
2007-04-30 22:11 ` Jeff Garzik
1 sibling, 1 reply; 95+ messages in thread
From: Chuck Ebbert @ 2007-04-30 22:06 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-ide, LKML
Jeff Garzik wrote:
> Chuck Ebbert wrote:
>> Jeff Garzik wrote:
>>> Jeff Garzik (8):
>>> libata/IDE: remove combined mode quirk
>>
>> You can't just remove the "combined_mode=" kernel parameter or
>> every Linux user who uses that will get an unbootable kernel
>> with no good way of diagnosing the problem. It should still
>> be accepted and just print a warning.
>
> No, most modern distros will simply Just Work(tm) due to mount by label,
> udev, and similar gadgets.
>
> As long as you have at least one (if not both) ATA drivers, you have a
> kernel that will boot your hardware. And by definition those using
> combined_mode= do indeed have the necessary drivers.
OK, this is a kernel parameter and should be fine. But you can't remove
*module* parameters for drivers needed for booting or the initrd will
fail to load the module with "unknown parameter" and users can't boot.
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-04-30 20:31 ` Alan Cox
@ 2007-04-30 20:51 ` alan
0 siblings, 0 replies; 95+ messages in thread
From: alan @ 2007-04-30 20:51 UTC (permalink / raw)
To: Alan Cox; +Cc: Stephen.Clark, Jeff Garzik, Chuck Ebbert, linux-ide, LKML
On Mon, 30 Apr 2007, Alan Cox wrote:
>> Yeah the kernel will boot but the hd performance is sh*t on my laptop. I
>> am running FC6 with
>> kernel 2.6.21 and without the combined_mode setting my disk performance
>> goes down to a
>> whopping 1.25mb/sec from 44mb/sec when I boot with combined_mode=libata.
>
> Then something is very wrong with the way you are setting it up, or the
> current code. Please post a dmesg booting with libata driving all your
> disks and it can get fixed before 2.6.22
>
> Do you happen to know how FC7test4 behaves on your box btw
I did the upgrade last night. Drive performance was SLLOOWW. When it
came time to the reboot, I had a corrupted disk. (Not certain if that was
the fault of the upgrade. I have to finish the fsck repairs first.) And
this is with ext3. Not good.
I have been seeing real bad driver performance on the latest FC6 kernel as
well.
--
"Invoking the supernatural can explain anything, and hence explains nothing."
- University of Utah bioengineering professor Gregory Clark
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-04-30 20:22 ` Stephen Clark
2007-04-30 20:31 ` Alan Cox
@ 2007-04-30 20:31 ` Jeff Garzik
2007-05-01 11:55 ` Stephen Clark
2007-05-01 21:38 ` Jesse Barnes
2 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2007-04-30 20:31 UTC (permalink / raw)
To: Stephen.Clark; +Cc: Chuck Ebbert, linux-ide, LKML
Stephen Clark wrote:
> Yeah the kernel will boot but the hd performance is sh*t on my laptop. I
> am running FC6 with
> kernel 2.6.21 and without the combined_mode setting my disk performance
> goes down to a
> whopping 1.25mb/sec from 44mb/sec when I boot with combined_mode=libata.
> It make my
> system unusable!
No, that's the split-driver configuration that causes the slowdown.
Now that both drivers fully support the hardware, either driver can make
things go full speed.
Please try testing the update first :)
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-04-30 20:22 ` Stephen Clark
@ 2007-04-30 20:31 ` Alan Cox
2007-04-30 20:51 ` alan
2007-04-30 20:31 ` Jeff Garzik
2007-05-01 21:38 ` Jesse Barnes
2 siblings, 1 reply; 95+ messages in thread
From: Alan Cox @ 2007-04-30 20:31 UTC (permalink / raw)
To: Stephen.Clark; +Cc: Jeff Garzik, Chuck Ebbert, linux-ide, LKML
> Yeah the kernel will boot but the hd performance is sh*t on my laptop. I
> am running FC6 with
> kernel 2.6.21 and without the combined_mode setting my disk performance
> goes down to a
> whopping 1.25mb/sec from 44mb/sec when I boot with combined_mode=libata.
Then something is very wrong with the way you are setting it up, or the
current code. Please post a dmesg booting with libata driving all your
disks and it can get fixed before 2.6.22
Do you happen to know how FC7test4 behaves on your box btw
Alan
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-04-30 20:05 ` Jeff Garzik
@ 2007-04-30 20:22 ` Stephen Clark
2007-04-30 20:31 ` Alan Cox
` (2 more replies)
2007-04-30 22:06 ` Chuck Ebbert
1 sibling, 3 replies; 95+ messages in thread
From: Stephen Clark @ 2007-04-30 20:22 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Chuck Ebbert, linux-ide, LKML
Jeff Garzik wrote:
>Chuck Ebbert wrote:
>
>
>>Jeff Garzik wrote:
>>
>>
>>>Jeff Garzik (8):
>>> libata/IDE: remove combined mode quirk
>>>
>>>
>>You can't just remove the "combined_mode=" kernel parameter or
>>every Linux user who uses that will get an unbootable kernel
>>with no good way of diagnosing the problem. It should still
>>be accepted and just print a warning.
>>
>>
>
>No, most modern distros will simply Just Work(tm) due to mount by label,
>udev, and similar gadgets.
>
>As long as you have at least one (if not both) ATA drivers, you have a
>kernel that will boot your hardware. And by definition those using
>combined_mode= do indeed have the necessary drivers.
>
> Jeff
>
>
>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at http://vger.kernel.org/majordomo-info.html
>Please read the FAQ at http://www.tux.org/lkml/
>
>
>
Please don't do this!
Yeah the kernel will boot but the hd performance is sh*t on my laptop. I
am running FC6 with
kernel 2.6.21 and without the combined_mode setting my disk performance
goes down to a
whopping 1.25mb/sec from 44mb/sec when I boot with combined_mode=libata.
It make my
system unusable!
Regards,
Steve
--
"They that give up essential liberty to obtain temporary safety,
deserve neither liberty nor safety." (Ben Franklin)
"The course of history shows that as a government grows, liberty
decreases." (Thomas Jefferson)
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-04-30 19:52 ` Chuck Ebbert
@ 2007-04-30 20:05 ` Jeff Garzik
2007-04-30 20:22 ` Stephen Clark
2007-04-30 22:06 ` Chuck Ebbert
0 siblings, 2 replies; 95+ messages in thread
From: Jeff Garzik @ 2007-04-30 20:05 UTC (permalink / raw)
To: Chuck Ebbert; +Cc: linux-ide, LKML
Chuck Ebbert wrote:
> Jeff Garzik wrote:
>> Jeff Garzik (8):
>> libata/IDE: remove combined mode quirk
>
> You can't just remove the "combined_mode=" kernel parameter or
> every Linux user who uses that will get an unbootable kernel
> with no good way of diagnosing the problem. It should still
> be accepted and just print a warning.
No, most modern distros will simply Just Work(tm) due to mount by label,
udev, and similar gadgets.
As long as you have at least one (if not both) ATA drivers, you have a
kernel that will boot your hardware. And by definition those using
combined_mode= do indeed have the necessary drivers.
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2007-04-29 16:15 Jeff Garzik
@ 2007-04-30 19:52 ` Chuck Ebbert
2007-04-30 20:05 ` Jeff Garzik
2007-05-01 21:34 ` Jesse Barnes
1 sibling, 1 reply; 95+ messages in thread
From: Chuck Ebbert @ 2007-04-30 19:52 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-ide, LKML
Jeff Garzik wrote:
>
> Jeff Garzik (8):
> libata/IDE: remove combined mode quirk
You can't just remove the "combined_mode=" kernel parameter or
every Linux user who uses that will get an unbootable kernel
with no good way of diagnosing the problem. It should still
be accepted and just print a warning.
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2007-04-29 16:15 Jeff Garzik
2007-04-30 19:52 ` Chuck Ebbert
2007-05-01 21:34 ` Jesse Barnes
0 siblings, 2 replies; 95+ messages in thread
From: Jeff Garzik @ 2007-04-29 16:15 UTC (permalink / raw)
To: linux-ide; +Cc: LKML
(just sent this upstream to Linus and Andrew)
Noteworthy changes:
* remove combined mode PCI quirk. IDE driver selection (libata or
old-IDE) is now determined purely by module load order.
* new driver API, that is far more like other kernel APIs:
alloc...register...unregister...free.
* More Alan PATA work
* Lots of other little bits.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
arch/i386/defconfig | 1 -
arch/parisc/configs/c3000_defconfig | 1 -
arch/x86_64/defconfig | 1 -
drivers/ata/Kconfig | 43 +-
drivers/ata/Makefile | 1 +
drivers/ata/ahci.c | 473 ++++++++---------
drivers/ata/ata_generic.c | 32 +-
drivers/ata/ata_piix.c | 56 +--
drivers/ata/libata-core.c | 1015 ++++++++++++++++++++++++-----------
drivers/ata/libata-eh.c | 15 +-
drivers/ata/libata-scsi.c | 85 +++-
drivers/ata/libata-sff.c | 631 ++++++++++++++--------
drivers/ata/libata.h | 10 +-
drivers/ata/pata_ali.c | 74 +---
drivers/ata/pata_amd.c | 89 ++--
drivers/ata/pata_artop.c | 26 +-
drivers/ata/pata_atiixp.c | 26 +-
drivers/ata/pata_cmd640.c | 312 +++++++++++
drivers/ata/pata_cmd64x.c | 34 +-
drivers/ata/pata_cs5520.c | 145 +++---
drivers/ata/pata_cs5530.c | 15 +-
drivers/ata/pata_cs5535.c | 24 +-
drivers/ata/pata_cypress.c | 14 +-
drivers/ata/pata_efar.c | 31 +-
drivers/ata/pata_hpt366.c | 26 +-
drivers/ata/pata_hpt37x.c | 381 ++++++--------
drivers/ata/pata_hpt3x2n.c | 74 ++-
drivers/ata/pata_hpt3x3.c | 22 +-
drivers/ata/pata_isapnp.c | 44 +-
drivers/ata/pata_it8213.c | 36 +-
drivers/ata/pata_it821x.c | 36 +-
drivers/ata/pata_ixp4xx_cf.c | 40 +-
drivers/ata/pata_legacy.c | 45 +-
drivers/ata/pata_marvell.c | 20 +-
drivers/ata/pata_mpc52xx.c | 49 +-
drivers/ata/pata_mpiix.c | 40 +-
drivers/ata/pata_netcell.c | 31 +-
drivers/ata/pata_ns87410.c | 6 +-
drivers/ata/pata_oldpiix.c | 6 +-
drivers/ata/pata_opti.c | 5 +-
drivers/ata/pata_optidma.c | 54 +-
drivers/ata/pata_pcmcia.c | 77 ++-
drivers/ata/pata_pdc2027x.c | 158 +++---
drivers/ata/pata_pdc202xx_old.c | 45 +--
drivers/ata/pata_platform.c | 44 +-
drivers/ata/pata_qdi.c | 47 +-
drivers/ata/pata_radisys.c | 37 +--
drivers/ata/pata_rz1000.c | 28 +-
drivers/ata/pata_sc1200.c | 1 +
drivers/ata/pata_scc.c | 51 +--
drivers/ata/pata_serverworks.c | 34 +-
drivers/ata/pata_sil680.c | 11 +-
drivers/ata/pata_sis.c | 109 +---
drivers/ata/pata_sl82c105.c | 2 +-
drivers/ata/pata_triflex.c | 4 +-
drivers/ata/pata_via.c | 27 +-
drivers/ata/pata_winbond.c | 101 ++--
drivers/ata/pdc_adma.c | 85 ++--
drivers/ata/sata_inic162x.c | 86 ++--
drivers/ata/sata_mv.c | 213 ++++----
drivers/ata/sata_nv.c | 130 ++---
drivers/ata/sata_promise.c | 398 ++++++++-------
drivers/ata/sata_qstor.c | 62 +--
drivers/ata/sata_sil.c | 118 ++--
drivers/ata/sata_sil24.c | 122 ++---
drivers/ata/sata_sis.c | 50 +--
drivers/ata/sata_svw.c | 107 ++--
drivers/ata/sata_sx4.c | 150 +++---
drivers/ata/sata_uli.c | 65 +--
drivers/ata/sata_via.c | 217 +++-----
drivers/ata/sata_vsc.c | 72 +--
drivers/pci/quirks.c | 113 ----
drivers/scsi/ipr.c | 3 +-
include/linux/ata.h | 10 +
include/linux/ioport.h | 1 -
include/linux/libata.h | 78 ++--
include/linux/pci.h | 1 +
include/linux/pci_ids.h | 1 -
kernel/resource.c | 21 -
lib/devres.c | 26 +
80 files changed, 3656 insertions(+), 3318 deletions(-)
create mode 100644 drivers/ata/pata_cmd640.c
Alan Cox (37):
libata: dev_config does not need ap and adev passing
libata: cable detection fixes
pata_cmd640: CMD640 PCI support
pata_it8213: Cable detect
pata_marvell: Cable and reset fixes
pata_sis: Clean up using cable_detect methods
pata_via: Use cable_detect method
pata_cmd640: Multiple updates
libata: Restore Kconfig updated experimental levels and correct
libata-core: fix comments on cable type
sata_promise: Switch to cable method, clean up some bits as a result
pata_platform: Add cable_detect method
pata_rz1000: support cable_detect
pata_sc1200: restore cable type
pata_radisys: support cable_detect
pata_atiixp: support ->cable_detect
pata_efar: support ->cable_detect
pata_hpt366: support ->cable_detect
pata_hpt37x: Updates from drivers/ide work
pata: expose set_mode method so it can be wrapped
libata-core: Fix the iordy methods
sata_sil: First step to removing ->post_set_mode
libata: Change prototype of mode_filter to remove ata_port*
pcmcia - spot slave decode flaws (for testing)
pata_ali: remove all the crap again and switch to cable_detect method
pata_qdI: restore cable detect
pata_netcell: re-remove all the crud
pata_sl82c105: restore cable detect method
pata_winbond: restore cable method
pata_optidma: rework for cable detect and to remove post_set_mode()
pata: cable methods
pata_winbond
pata_pdc2027x: Updates
libata: HPA support
ata_timing: ensure t->cycle is always correct
pata_hpt3x2n: Add HPT371N support and other bits
pata_hpt37x: Further small fixes
Andrew Morton (3):
git-libata-all-ipr-fix
ata: printk warning fixes
drivers/ata/pata_cmd640.c: fix build with CONFIG_PM=n
Conke Hu (1):
ahci.c: remove non-existing SB600 raid id (re-send)
Dmitriy Monakhov (1):
libata: handle ata_pci_device_do_resume() failure while resuming
Jeff Garzik (8):
[libata] sata_mv: remove extra braces
[libata] export sata_print_link_status()
[libata] sata_mv: clean up DMA boundary issues, turn on 64-bit DMA
[libata] Update several PATA drivers for new ->cable_detect hook
[libata] More PATA driver ->cable_detect support
[libata] sata_mv: support ->cable_detect
[libata] turn on !IORDY filter
libata/IDE: remove combined mode quirk
Mark Lord (3):
RESEND: libata: check cdb len per dev instead of per host
libata: add support for READ/WRITE LONG
libata: Handle drives that require a spin-up command before first access
Mikael Pettersson (4):
sata_promise: add missing cable_detect hooks
sata_promise: separate SATA and PATA ops
sata_promise: decode and report error reasons
sata_promise: fix error decode regression
Milind Arun Choudhary (1):
SPIN_LOCK_UNLOCKED cleanup in drivers/ata/pata_winbond.c
Morrison, Tom (1):
Support for Marvell 7042 Chip
Robert Hancock (2):
libata: warn if speed limited due to 40-wire cable
sata_nv: don't read shadow registers when in ADMA mode
Robin H\. Johnson (1):
Add notation that the Asus W5F laptop has a short cable instead of 80-wire.
Tejun Heo (24):
iomap: implement pcim_iounmap_regions()
libata: hardreset on SERR_INTERNAL
ahci: implement ata_save/restore_initial_config()
ahci: move port_map handling to ahci_save_initial_config()
libata: fix native mode disabled port handling
libata: improve AC_ERR_DEV handling for ->post_internal_cmd
libata: kill type mismatch compile warning
ahci: add PCI ID for new VIA chip
libata: allocate ap separately from shost
libata: separate out ata_host_start()
libata: separate out ata_host_alloc() and ata_host_register()
libata: implement ata_host_alloc_pinfo() and ata_host_register()
libata: convert legacy PCI host handling to new init model
libata: convert native PCI host handling to new init model
libata: add init helpers including ata_pci_prepare_native_host()
libata: convert drivers with combined SATA/PATA ports to new init model
libata: convert ata_pci_init_native_mode() users to new init model
libata: convert the remaining SATA drivers to new init model
libata: convert the remaining PATA drivers to new init model
libata: kill probe_ent and related helpers
pata_amd: remove contamination added during cable_detect conversion
libata: add missing call to ->cable_detect() in new EH path
ahci: consolidate common port flags
libata: separate ATA_EHI_DID_RESET into DID_SOFTRESET and DID_HARDRESET
[patch snipped due to size; it's in git]
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2006-12-14 23:08 Jeff Garzik
@ 2006-12-15 1:14 ` Alan
0 siblings, 0 replies; 95+ messages in thread
From: Alan @ 2006-12-15 1:14 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Andrew Morton, Linus Torvalds, linux-ide, LKML
>
> +config PATA_IT8213
> + tristate "IT8213 PATA support (Experimental)"
> + depends on PCI && EXPERIMENTAL
> + help
> + This option enables support for the ITE 821 PATA
Typo (IT8213) - probably my fault but only just noticed it
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2006-12-14 23:08 Jeff Garzik
2006-12-15 1:14 ` Alan
0 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2006-12-14 23:08 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Includes some pre-window-closing stuff (new drivers), but I was waiting
on some bug fixes before pushing.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/Kconfig | 20 ++-
drivers/ata/Makefile | 2 +
drivers/ata/ahci.c | 2 -
drivers/ata/ata_piix.c | 24 ++-
drivers/ata/libata-core.c | 16 +-
drivers/ata/libata-scsi.c | 4 +-
drivers/ata/pata_ali.c | 4 +-
drivers/ata/pata_cs5520.c | 2 +-
drivers/ata/pata_cs5530.c | 8 +-
drivers/ata/pata_hpt366.c | 2 +-
drivers/ata/pata_hpt37x.c | 4 +-
drivers/ata/pata_hpt3x3.c | 2 +-
drivers/ata/pata_it8213.c | 354 +++++++++++++++++++++++++
drivers/ata/pata_jmicron.c | 2 +-
drivers/ata/pata_marvell.c | 4 +-
drivers/ata/pata_mpc52xx.c | 563 ++++++++++++++++++++++++++++++++++++++++
drivers/ata/pata_serverworks.c | 2 +-
drivers/ata/pata_sil680.c | 2 +-
drivers/ata/pata_sis.c | 2 +-
drivers/ata/pata_via.c | 10 +-
drivers/ata/pata_winbond.c | 16 +-
drivers/ata/sata_nv.c | 18 +-
drivers/ata/sata_sis.c | 79 ++++--
drivers/ata/sata_svw.c | 41 +++-
drivers/ata/sata_via.c | 2 +-
include/linux/libata.h | 2 +-
include/linux/pci_ids.h | 1 +
27 files changed, 1099 insertions(+), 89 deletions(-)
create mode 100644 drivers/ata/pata_it8213.c
create mode 100644 drivers/ata/pata_mpc52xx.c
Alan (1):
pata_it8213: Add new driver for the IT8213 card
Jason Gaston (1):
ata_piix: IDE mode SATA patch for Intel ICH9
Jeff Garzik (3):
[libata] use kmap_atomic(KM_IRQ0) in SCSI simulator
[libata] trim trailing whitespace
[libata] sata_svw: Disable ATAPI DMA on current boards (errata workaround)
Sylvain Munaut (1):
libata: Add support for the MPC52xx ATA controller
Tejun Heo (3):
ata_piix: use piix_host_stop() in ich_pata_ops
libata: don't initialize sg in ata_exec_internal() if DMA_NONE (take #2)
ahci: do not mangle saved HOST_CAP while resetting controller
Uwe Koziolek (1):
sata_sis: support SiS966/966L
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 984ab28..fb1de86 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -292,7 +292,7 @@ config PATA_ISAPNP
If unsure, say N.
config PATA_IT821X
- tristate "IT821x PATA support (Experimental)"
+ tristate "IT8211/2 PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the ITE 8211 and 8212
@@ -301,6 +301,15 @@ config PATA_IT821X
If unsure, say N.
+config PATA_IT8213
+ tristate "IT8213 PATA support (Experimental)"
+ depends on PCI && EXPERIMENTAL
+ help
+ This option enables support for the ITE 821 PATA
+ controllers via the new ATA layer.
+
+ If unsure, say N.
+
config PATA_JMICRON
tristate "JMicron PATA support"
depends on PCI
@@ -337,6 +346,15 @@ config PATA_MARVELL
If unsure, say N.
+config PATA_MPC52xx
+ tristate "Freescale MPC52xx SoC internal IDE"
+ depends on PPC_MPC52xx
+ help
+ This option enables support for integrated IDE controller
+ of the Freescale MPC52xx SoC.
+
+ If unsure, say N.
+
config PATA_MPIIX
tristate "Intel PATA MPIIX support"
depends on PCI
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index bc3d81a..a0df15d 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -33,11 +33,13 @@ obj-$(CONFIG_PATA_HPT3X2N) += pata_hpt3x2n.o
obj-$(CONFIG_PATA_HPT3X3) += pata_hpt3x3.o
obj-$(CONFIG_PATA_ISAPNP) += pata_isapnp.o
obj-$(CONFIG_PATA_IT821X) += pata_it821x.o
+obj-$(CONFIG_PATA_IT8213) += pata_it8213.o
obj-$(CONFIG_PATA_JMICRON) += pata_jmicron.o
obj-$(CONFIG_PATA_NETCELL) += pata_netcell.o
obj-$(CONFIG_PATA_NS87410) += pata_ns87410.o
obj-$(CONFIG_PATA_OPTI) += pata_opti.o
obj-$(CONFIG_PATA_OPTIDMA) += pata_optidma.o
+obj-$(CONFIG_PATA_MPC52xx) += pata_mpc52xx.o
obj-$(CONFIG_PATA_MARVELL) += pata_marvell.o
obj-$(CONFIG_PATA_MPIIX) += pata_mpiix.o
obj-$(CONFIG_PATA_OLDPIIX) += pata_oldpiix.o
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index f36da48..dbae6d9 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -645,8 +645,6 @@ static int ahci_reset_controller(void __iomem *mmio, struct pci_dev *pdev)
u32 cap_save, impl_save, tmp;
cap_save = readl(mmio + HOST_CAP);
- cap_save &= ( (1<<28) | (1<<17) );
- cap_save |= (1 << 27);
impl_save = readl(mmio + HOST_PORTS_IMPL);
/* global controller reset */
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index c7de0bb..7959e4c 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -226,14 +226,26 @@ static const struct pci_device_id piix_pci_tbl[] = {
{ 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
/* 2801GBM/GHM (ICH7M, identical to ICH6M) */
{ 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata_ahci },
- /* Enterprise Southbridge 2 (where's the datasheet?) */
+ /* Enterprise Southbridge 2 (631xESB/632xESB) */
{ 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
- /* SATA Controller 1 IDE (ICH8, no datasheet yet) */
+ /* SATA Controller 1 IDE (ICH8) */
{ 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
- /* SATA Controller 2 IDE (ICH8, ditto) */
+ /* SATA Controller 2 IDE (ICH8) */
{ 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
- /* Mobile SATA Controller IDE (ICH8M, ditto) */
+ /* Mobile SATA Controller IDE (ICH8M) */
{ 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9) */
+ { 0x8086, 0x2920, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9) */
+ { 0x8086, 0x2921, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9) */
+ { 0x8086, 0x2926, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9M) */
+ { 0x8086, 0x2928, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9M) */
+ { 0x8086, 0x292d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9M) */
+ { 0x8086, 0x292e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
{ } /* terminate list */
};
@@ -330,7 +342,7 @@ static const struct ata_port_operations ich_pata_ops = {
.port_start = ata_port_start,
.port_stop = ata_port_stop,
- .host_stop = ata_host_stop,
+ .host_stop = piix_host_stop,
};
static const struct ata_port_operations piix_sata_ops = {
@@ -620,7 +632,7 @@ static int piix_pata_prereset(struct ata_port *ap)
if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no]))
return -ENOENT;
-
+
ap->cbl = ATA_CBL_PATA40;
return ata_std_prereset(ap);
}
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 011c0a8..fd20e7a 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -1332,7 +1332,7 @@ unsigned ata_exec_internal_sg(struct ata_device *dev,
}
/**
- * ata_exec_internal_sg - execute libata internal command
+ * ata_exec_internal - execute libata internal command
* @dev: Device to which the command is sent
* @tf: Taskfile registers for the command and the result
* @cdb: CDB for packet command
@@ -1353,11 +1353,17 @@ unsigned ata_exec_internal(struct ata_device *dev,
struct ata_taskfile *tf, const u8 *cdb,
int dma_dir, void *buf, unsigned int buflen)
{
- struct scatterlist sg;
+ struct scatterlist *psg = NULL, sg;
+ unsigned int n_elem = 0;
- sg_init_one(&sg, buf, buflen);
+ if (dma_dir != DMA_NONE) {
+ WARN_ON(!buf);
+ sg_init_one(&sg, buf, buflen);
+ psg = &sg;
+ n_elem++;
+ }
- return ata_exec_internal_sg(dev, tf, cdb, dma_dir, &sg, 1);
+ return ata_exec_internal_sg(dev, tf, cdb, dma_dir, psg, n_elem);
}
/**
@@ -5773,7 +5779,7 @@ int ata_device_add(const struct ata_probe_ent *ent)
int rc;
DPRINTK("ENTER\n");
-
+
if (ent->irq == 0) {
dev_printk(KERN_ERR, dev, "is not available: No interrupt assigned.\n");
return 0;
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 664e137..a4790be 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -1539,7 +1539,7 @@ static unsigned int ata_scsi_rbuf_get(struct scsi_cmnd *cmd, u8 **buf_out)
struct scatterlist *sg;
sg = (struct scatterlist *) cmd->request_buffer;
- buf = kmap_atomic(sg->page, KM_USER0) + sg->offset;
+ buf = kmap_atomic(sg->page, KM_IRQ0) + sg->offset;
buflen = sg->length;
} else {
buf = cmd->request_buffer;
@@ -1567,7 +1567,7 @@ static inline void ata_scsi_rbuf_put(struct scsi_cmnd *cmd, u8 *buf)
struct scatterlist *sg;
sg = (struct scatterlist *) cmd->request_buffer;
- kunmap_atomic(buf - sg->offset, KM_USER0);
+ kunmap_atomic(buf - sg->offset, KM_IRQ0);
}
}
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index c5d61d1..2035417 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -504,7 +504,7 @@ static struct ata_port_operations ali_c5_port_ops = {
* Perform the setup on the device that must be done both at boot
* and at resume time.
*/
-
+
static void ali_init_chipset(struct pci_dev *pdev)
{
u8 rev, tmp;
@@ -655,7 +655,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
port_info[0] = port_info[1] = &info_c5;
ali_init_chipset(pdev);
-
+
isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
if (isa_bridge && rev >= 0x20 && rev < 0xC2) {
/* Are we paired with a UDMA capable chip */
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c
index 9f165a8..476b879 100644
--- a/drivers/ata/pata_cs5520.c
+++ b/drivers/ata/pata_cs5520.c
@@ -305,7 +305,7 @@ static void __devexit cs5520_remove_one(struct pci_dev *pdev)
* Do any reconfiguration work needed by a resume from RAM. We need
* to restore DMA mode support on BIOSen which disabled it
*/
-
+
static int cs5520_reinit_one(struct pci_dev *pdev)
{
u8 pcicfg;
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
index 1c62801..9b9d911 100644
--- a/drivers/ata/pata_cs5530.c
+++ b/drivers/ata/pata_cs5530.c
@@ -247,7 +247,7 @@ static int cs5530_is_palmax(void)
* Perform the chip initialisation work that is shared between both
* setup and resume paths
*/
-
+
static int cs5530_init_chip(void)
{
struct pci_dev *master_0 = NULL, *cs5530_0 = NULL, *dev = NULL;
@@ -357,11 +357,11 @@ static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &cs5530_port_ops
};
static struct ata_port_info *port_info[2] = { &info, &info };
-
+
/* Chip initialisation */
if (cs5530_init_chip())
return -ENODEV;
-
+
if (cs5530_is_palmax())
port_info[1] = &info_palmax_secondary;
@@ -375,7 +375,7 @@ static int cs5530_reinit_one(struct pci_dev *pdev)
BUG_ON(cs5530_init_chip());
return ata_pci_device_resume(pdev);
}
-
+
static const struct pci_device_id cs5530[] = {
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), },
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index 2663599..8cf167e 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -232,7 +232,7 @@ static int hpt36x_pre_reset(struct ata_port *ap)
if (!pci_test_config_bits(pdev, &hpt36x_enable_bits[ap->port_no]))
return -ENOENT;
-
+
pci_read_config_byte(pdev, 0x5A, &ata66);
if (ata66 & (1 << ap->port_no))
ap->cbl = ATA_CBL_PATA40;
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index 47082df..e51651b 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -459,7 +459,7 @@ static int hpt37x_pre_reset(struct ata_port *ap)
};
if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no]))
return -ENOENT;
-
+
pci_read_config_byte(pdev, 0x5B, &scr2);
pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
/* Cable register now active */
@@ -504,7 +504,7 @@ static int hpt374_pre_reset(struct ata_port *ap)
if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no]))
return -ENOENT;
-
+
/* Do the extra channel work */
pci_read_config_word(pdev, 0x52, &mcr3);
pci_read_config_word(pdev, 0x56, &mcr6);
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
index 5f1d385..5caf167 100644
--- a/drivers/ata/pata_hpt3x3.c
+++ b/drivers/ata/pata_hpt3x3.c
@@ -164,7 +164,7 @@ static struct ata_port_operations hpt3x3_port_ops = {
*
* Perform the setup required at boot and on resume.
*/
-
+
static void hpt3x3_init_chipset(struct pci_dev *dev)
{
u16 cmd;
diff --git a/drivers/ata/pata_it8213.c b/drivers/ata/pata_it8213.c
new file mode 100644
index 0000000..7e9a416
--- /dev/null
+++ b/drivers/ata/pata_it8213.c
@@ -0,0 +1,354 @@
+/*
+ * pata_it8213.c - iTE Tech. Inc. IT8213 PATA driver
+ *
+ * The IT8213 is a very Intel ICH like device for timing purposes, having
+ * a similar register layout and the same split clock arrangement. Cable
+ * detection is different, and it does not have slave channels or all the
+ * clutter of later ICH/SATA setups.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME "pata_it8213"
+#define DRV_VERSION "0.0.2"
+
+/**
+ * it8213_pre_reset - check for 40/80 pin
+ * @ap: Port
+ *
+ * Perform cable detection for the 8213 ATA interface. This is
+ * different to the PIIX arrangement
+ */
+
+static int it8213_pre_reset(struct ata_port *ap)
+{
+ static const struct pci_bits it8213_enable_bits[] = {
+ { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */
+ };
+
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u8 tmp;
+
+ if (!pci_test_config_bits(pdev, &it8213_enable_bits[ap->port_no]))
+ return -ENOENT;
+
+ pci_read_config_byte(pdev, 0x42, &tmp);
+ if (tmp & 2) /* The initial docs are incorrect */
+ ap->cbl = ATA_CBL_PATA40;
+ else
+ ap->cbl = ATA_CBL_PATA80;
+ return ata_std_prereset(ap);
+}
+
+/**
+ * it8213_probe_reset - Probe specified port on PATA host controller
+ * @ap: Port to probe
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void it8213_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, it8213_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ * it8213_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: um
+ *
+ * Set PIO mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int pio = adev->pio_mode - XFER_PIO_0;
+ struct pci_dev *dev = to_pci_dev(ap->host->dev);
+ unsigned int idetm_port= ap->port_no ? 0x42 : 0x40;
+ u16 idetm_data;
+ int control = 0;
+
+ /*
+ * See Intel Document 298600-004 for the timing programing rules
+ * for PIIX/ICH. The 8213 is a clone so very similar
+ */
+
+ static const /* ISP RTC */
+ u8 timings[][2] = { { 0, 0 },
+ { 0, 0 },
+ { 1, 0 },
+ { 2, 1 },
+ { 2, 3 }, };
+
+ if (pio > 2)
+ control |= 1; /* TIME1 enable */
+ if (ata_pio_need_iordy(adev)) /* PIO 3/4 require IORDY */
+ control |= 2; /* IORDY enable */
+ /* Bit 2 is set for ATAPI on the IT8213 - reverse of ICH/PIIX */
+ if (adev->class != ATA_DEV_ATA)
+ control |= 4;
+
+ pci_read_config_word(dev, idetm_port, &idetm_data);
+
+ /* Enable PPE, IE and TIME as appropriate */
+
+ if (adev->devno == 0) {
+ idetm_data &= 0xCCF0;
+ idetm_data |= control;
+ idetm_data |= (timings[pio][0] << 12) |
+ (timings[pio][1] << 8);
+ } else {
+ u8 slave_data;
+
+ idetm_data &= 0xCC0F;
+ idetm_data |= (control << 4);
+
+ /* Slave timing in seperate register */
+ pci_read_config_byte(dev, 0x44, &slave_data);
+ slave_data &= 0xF0;
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << 4;
+ pci_write_config_byte(dev, 0x44, slave_data);
+ }
+
+ idetm_data |= 0x4000; /* Ensure SITRE is enabled */
+ pci_write_config_word(dev, idetm_port, idetm_data);
+}
+
+/**
+ * it8213_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device to program
+ *
+ * Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ * This device is basically an ICH alike.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void it8213_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *dev = to_pci_dev(ap->host->dev);
+ u16 master_data;
+ u8 speed = adev->dma_mode;
+ int devid = adev->devno;
+ u8 udma_enable;
+
+ static const /* ISP RTC */
+ u8 timings[][2] = { { 0, 0 },
+ { 0, 0 },
+ { 1, 0 },
+ { 2, 1 },
+ { 2, 3 }, };
+
+ pci_read_config_word(dev, 0x40, &master_data);
+ pci_read_config_byte(dev, 0x48, &udma_enable);
+
+ if (speed >= XFER_UDMA_0) {
+ unsigned int udma = adev->dma_mode - XFER_UDMA_0;
+ u16 udma_timing;
+ u16 ideconf;
+ int u_clock, u_speed;
+
+ /* Clocks follow the PIIX style */
+ u_speed = min(2 - (udma & 1), udma);
+ if (udma == 5)
+ u_clock = 0x1000; /* 100Mhz */
+ else if (udma > 2)
+ u_clock = 1; /* 66Mhz */
+ else
+ u_clock = 0; /* 33Mhz */
+
+ udma_enable |= (1 << devid);
+
+ /* Load the UDMA mode number */
+ pci_read_config_word(dev, 0x4A, &udma_timing);
+ udma_timing &= ~(3 << (4 * devid));
+ udma_timing |= (udma & 3) << (4 * devid);
+ pci_write_config_word(dev, 0x4A, udma_timing);
+
+ /* Load the clock selection */
+ pci_read_config_word(dev, 0x54, &ideconf);
+ ideconf &= ~(0x1001 << devid);
+ ideconf |= u_clock << devid;
+ pci_write_config_word(dev, 0x54, ideconf);
+ } else {
+ /*
+ * MWDMA is driven by the PIO timings. We must also enable
+ * IORDY unconditionally along with TIME1. PPE has already
+ * been set when the PIO timing was set.
+ */
+ unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0;
+ unsigned int control;
+ u8 slave_data;
+ static const unsigned int needed_pio[3] = {
+ XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
+ };
+ int pio = needed_pio[mwdma] - XFER_PIO_0;
+
+ control = 3; /* IORDY|TIME1 */
+
+ /* If the drive MWDMA is faster than it can do PIO then
+ we must force PIO into PIO0 */
+
+ if (adev->pio_mode < needed_pio[mwdma])
+ /* Enable DMA timing only */
+ control |= 8; /* PIO cycles in PIO0 */
+
+ if (devid) { /* Slave */
+ master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */
+ master_data |= control << 4;
+ pci_read_config_byte(dev, 0x44, &slave_data);
+ slave_data &= (0x0F + 0xE1 * ap->port_no);
+ /* Load the matching timing */
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
+ pci_write_config_byte(dev, 0x44, slave_data);
+ } else { /* Master */
+ master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY
+ and master timing bits */
+ master_data |= control;
+ master_data |=
+ (timings[pio][0] << 12) |
+ (timings[pio][1] << 8);
+ }
+ udma_enable &= ~(1 << devid);
+ pci_write_config_word(dev, 0x40, master_data);
+ }
+ pci_write_config_byte(dev, 0x48, udma_enable);
+}
+
+static struct scsi_host_template it8213_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .max_sectors = ATA_MAX_SECTORS,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
+};
+
+static const struct ata_port_operations it8213_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = it8213_set_piomode,
+ .set_dmamode = it8213_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = it8213_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_pio_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_host_stop,
+};
+
+
+/**
+ * it8213_init_one - Register 8213 ATA PCI device with kernel services
+ * @pdev: PCI device to register
+ * @ent: Entry in it8213_pci_tbl matching with @pdev
+ *
+ * Called from kernel PCI layer.
+ *
+ * LOCKING:
+ * Inherited from PCI layer (may sleep).
+ *
+ * RETURNS:
+ * Zero on success, or -ERRNO value.
+ */
+
+static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ static int printed_version;
+ static struct ata_port_info info = {
+ .sht = &it8213_sht,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x1f, /* UDMA 100 */
+ .port_ops = &it8213_ops,
+ };
+ static struct ata_port_info *port_info[2] = { &info, &info };
+
+ if (!printed_version++)
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "version " DRV_VERSION "\n");
+
+ /* Current IT8213 stuff is single port */
+ return ata_pci_init_one(pdev, port_info, 1);
+}
+
+static const struct pci_device_id it8213_pci_tbl[] = {
+ { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8213), },
+
+ { } /* terminate list */
+};
+
+static struct pci_driver it8213_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = it8213_pci_tbl,
+ .probe = it8213_init_one,
+ .remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
+};
+
+static int __init it8213_init(void)
+{
+ return pci_register_driver(&it8213_pci_driver);
+}
+
+static void __exit it8213_exit(void)
+{
+ pci_unregister_driver(&it8213_pci_driver);
+}
+
+module_init(it8213_init);
+module_exit(it8213_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for the ITE 8213");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, it8213_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
index 2d661cb..efb1b6d 100644
--- a/drivers/ata/pata_jmicron.c
+++ b/drivers/ata/pata_jmicron.c
@@ -229,7 +229,7 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i
static int jmicron_reinit_one(struct pci_dev *pdev)
{
u32 reg;
-
+
switch(pdev->device) {
case PCI_DEVICE_ID_JMICRON_JMB368:
break;
diff --git a/drivers/ata/pata_marvell.c b/drivers/ata/pata_marvell.c
index 1c810ea..af93533 100644
--- a/drivers/ata/pata_marvell.c
+++ b/drivers/ata/pata_marvell.c
@@ -45,10 +45,10 @@ static int marvell_pre_reset(struct ata_port *ap)
for(i = 0; i <= 0x0F; i++)
printk("%02X:%02X ", i, readb(barp + i));
printk("\n");
-
+
devices = readl(barp + 0x0C);
pci_iounmap(pdev, barp);
-
+
if ((pdev->device == 0x6145) && (ap->port_no == 0) &&
(!(devices & 0x10))) /* PATA enable ? */
return -ENOENT;
diff --git a/drivers/ata/pata_mpc52xx.c b/drivers/ata/pata_mpc52xx.c
new file mode 100644
index 0000000..8b7019a
--- /dev/null
+++ b/drivers/ata/pata_mpc52xx.c
@@ -0,0 +1,563 @@
+/*
+ * drivers/ata/pata_mpc52xx.c
+ *
+ * libata driver for the Freescale MPC52xx on-chip IDE interface
+ *
+ * Copyright (C) 2006 Sylvain Munaut <tnt@246tNt.com>
+ * Copyright (C) 2003 Mipsys - Benjamin Herrenschmidt
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/libata.h>
+
+#include <asm/io.h>
+#include <asm/types.h>
+#include <asm/prom.h>
+#include <asm/of_platform.h>
+#include <asm/mpc52xx.h>
+
+
+#define DRV_NAME "mpc52xx_ata"
+#define DRV_VERSION "0.1.0"
+
+
+/* Private structures used by the driver */
+struct mpc52xx_ata_timings {
+ u32 pio1;
+ u32 pio2;
+};
+
+struct mpc52xx_ata_priv {
+ unsigned int ipb_period;
+ struct mpc52xx_ata __iomem * ata_regs;
+ int ata_irq;
+ struct mpc52xx_ata_timings timings[2];
+ int csel;
+};
+
+
+/* ATAPI-4 PIO specs (in ns) */
+static const int ataspec_t0[5] = {600, 383, 240, 180, 120};
+static const int ataspec_t1[5] = { 70, 50, 30, 30, 25};
+static const int ataspec_t2_8[5] = {290, 290, 290, 80, 70};
+static const int ataspec_t2_16[5] = {165, 125, 100, 80, 70};
+static const int ataspec_t2i[5] = { 0, 0, 0, 70, 25};
+static const int ataspec_t4[5] = { 30, 20, 15, 10, 10};
+static const int ataspec_ta[5] = { 35, 35, 35, 35, 35};
+
+#define CALC_CLKCYC(c,v) ((((v)+(c)-1)/(c)))
+
+
+/* Bit definitions inside the registers */
+#define MPC52xx_ATA_HOSTCONF_SMR 0x80000000UL /* State machine reset */
+#define MPC52xx_ATA_HOSTCONF_FR 0x40000000UL /* FIFO Reset */
+#define MPC52xx_ATA_HOSTCONF_IE 0x02000000UL /* Enable interrupt in PIO */
+#define MPC52xx_ATA_HOSTCONF_IORDY 0x01000000UL /* Drive supports IORDY protocol */
+
+#define MPC52xx_ATA_HOSTSTAT_TIP 0x80000000UL /* Transaction in progress */
+#define MPC52xx_ATA_HOSTSTAT_UREP 0x40000000UL /* UDMA Read Extended Pause */
+#define MPC52xx_ATA_HOSTSTAT_RERR 0x02000000UL /* Read Error */
+#define MPC52xx_ATA_HOSTSTAT_WERR 0x01000000UL /* Write Error */
+
+#define MPC52xx_ATA_FIFOSTAT_EMPTY 0x01 /* FIFO Empty */
+
+#define MPC52xx_ATA_DMAMODE_WRITE 0x01 /* Write DMA */
+#define MPC52xx_ATA_DMAMODE_READ 0x02 /* Read DMA */
+#define MPC52xx_ATA_DMAMODE_UDMA 0x04 /* UDMA enabled */
+#define MPC52xx_ATA_DMAMODE_IE 0x08 /* Enable drive interrupt to CPU in DMA mode */
+#define MPC52xx_ATA_DMAMODE_FE 0x10 /* FIFO Flush enable in Rx mode */
+#define MPC52xx_ATA_DMAMODE_FR 0x20 /* FIFO Reset */
+#define MPC52xx_ATA_DMAMODE_HUT 0x40 /* Host UDMA burst terminate */
+
+
+/* Structure of the hardware registers */
+struct mpc52xx_ata {
+
+ /* Host interface registers */
+ u32 config; /* ATA + 0x00 Host configuration */
+ u32 host_status; /* ATA + 0x04 Host controller status */
+ u32 pio1; /* ATA + 0x08 PIO Timing 1 */
+ u32 pio2; /* ATA + 0x0c PIO Timing 2 */
+ u32 mdma1; /* ATA + 0x10 MDMA Timing 1 */
+ u32 mdma2; /* ATA + 0x14 MDMA Timing 2 */
+ u32 udma1; /* ATA + 0x18 UDMA Timing 1 */
+ u32 udma2; /* ATA + 0x1c UDMA Timing 2 */
+ u32 udma3; /* ATA + 0x20 UDMA Timing 3 */
+ u32 udma4; /* ATA + 0x24 UDMA Timing 4 */
+ u32 udma5; /* ATA + 0x28 UDMA Timing 5 */
+ u32 share_cnt; /* ATA + 0x2c ATA share counter */
+ u32 reserved0[3];
+
+ /* FIFO registers */
+ u32 fifo_data; /* ATA + 0x3c */
+ u8 fifo_status_frame; /* ATA + 0x40 */
+ u8 fifo_status; /* ATA + 0x41 */
+ u16 reserved7[1];
+ u8 fifo_control; /* ATA + 0x44 */
+ u8 reserved8[5];
+ u16 fifo_alarm; /* ATA + 0x4a */
+ u16 reserved9;
+ u16 fifo_rdp; /* ATA + 0x4e */
+ u16 reserved10;
+ u16 fifo_wrp; /* ATA + 0x52 */
+ u16 reserved11;
+ u16 fifo_lfrdp; /* ATA + 0x56 */
+ u16 reserved12;
+ u16 fifo_lfwrp; /* ATA + 0x5a */
+
+ /* Drive TaskFile registers */
+ u8 tf_control; /* ATA + 0x5c TASKFILE Control/Alt Status */
+ u8 reserved13[3];
+ u16 tf_data; /* ATA + 0x60 TASKFILE Data */
+ u16 reserved14;
+ u8 tf_features; /* ATA + 0x64 TASKFILE Features/Error */
+ u8 reserved15[3];
+ u8 tf_sec_count; /* ATA + 0x68 TASKFILE Sector Count */
+ u8 reserved16[3];
+ u8 tf_sec_num; /* ATA + 0x6c TASKFILE Sector Number */
+ u8 reserved17[3];
+ u8 tf_cyl_low; /* ATA + 0x70 TASKFILE Cylinder Low */
+ u8 reserved18[3];
+ u8 tf_cyl_high; /* ATA + 0x74 TASKFILE Cylinder High */
+ u8 reserved19[3];
+ u8 tf_dev_head; /* ATA + 0x78 TASKFILE Device/Head */
+ u8 reserved20[3];
+ u8 tf_command; /* ATA + 0x7c TASKFILE Command/Status */
+ u8 dma_mode; /* ATA + 0x7d ATA Host DMA Mode configuration */
+ u8 reserved21[2];
+};
+
+
+/* ======================================================================== */
+/* Aux fns */
+/* ======================================================================== */
+
+
+/* MPC52xx low level hw control */
+
+static int
+mpc52xx_ata_compute_pio_timings(struct mpc52xx_ata_priv *priv, int dev, int pio)
+{
+ struct mpc52xx_ata_timings *timing = &priv->timings[dev];
+ unsigned int ipb_period = priv->ipb_period;
+ unsigned int t0, t1, t2_8, t2_16, t2i, t4, ta;
+
+ if ((pio<0) || (pio>4))
+ return -EINVAL;
+
+ t0 = CALC_CLKCYC(ipb_period, 1000 * ataspec_t0[pio]);
+ t1 = CALC_CLKCYC(ipb_period, 1000 * ataspec_t1[pio]);
+ t2_8 = CALC_CLKCYC(ipb_period, 1000 * ataspec_t2_8[pio]);
+ t2_16 = CALC_CLKCYC(ipb_period, 1000 * ataspec_t2_16[pio]);
+ t2i = CALC_CLKCYC(ipb_period, 1000 * ataspec_t2i[pio]);
+ t4 = CALC_CLKCYC(ipb_period, 1000 * ataspec_t4[pio]);
+ ta = CALC_CLKCYC(ipb_period, 1000 * ataspec_ta[pio]);
+
+ timing->pio1 = (t0 << 24) | (t2_8 << 16) | (t2_16 << 8) | (t2i);
+ timing->pio2 = (t4 << 24) | (t1 << 16) | (ta << 8);
+
+ return 0;
+}
+
+static void
+mpc52xx_ata_apply_timings(struct mpc52xx_ata_priv *priv, int device)
+{
+ struct mpc52xx_ata __iomem *regs = priv->ata_regs;
+ struct mpc52xx_ata_timings *timing = &priv->timings[device];
+
+ out_be32(®s->pio1, timing->pio1);
+ out_be32(®s->pio2, timing->pio2);
+ out_be32(®s->mdma1, 0);
+ out_be32(®s->mdma2, 0);
+ out_be32(®s->udma1, 0);
+ out_be32(®s->udma2, 0);
+ out_be32(®s->udma3, 0);
+ out_be32(®s->udma4, 0);
+ out_be32(®s->udma5, 0);
+
+ priv->csel = device;
+}
+
+static int
+mpc52xx_ata_hw_init(struct mpc52xx_ata_priv *priv)
+{
+ struct mpc52xx_ata __iomem *regs = priv->ata_regs;
+ int tslot;
+
+ /* Clear share_cnt (all sample code do this ...) */
+ out_be32(®s->share_cnt, 0);
+
+ /* Configure and reset host */
+ out_be32(®s->config,
+ MPC52xx_ATA_HOSTCONF_IE |
+ MPC52xx_ATA_HOSTCONF_IORDY |
+ MPC52xx_ATA_HOSTCONF_SMR |
+ MPC52xx_ATA_HOSTCONF_FR);
+
+ udelay(10);
+
+ out_be32(®s->config,
+ MPC52xx_ATA_HOSTCONF_IE |
+ MPC52xx_ATA_HOSTCONF_IORDY);
+
+ /* Set the time slot to 1us */
+ tslot = CALC_CLKCYC(priv->ipb_period, 1000000);
+ out_be32(®s->share_cnt, tslot << 16 );
+
+ /* Init timings to PIO0 */
+ memset(priv->timings, 0x00, 2*sizeof(struct mpc52xx_ata_timings));
+
+ mpc52xx_ata_compute_pio_timings(priv, 0, 0);
+ mpc52xx_ata_compute_pio_timings(priv, 1, 0);
+
+ mpc52xx_ata_apply_timings(priv, 0);
+
+ return 0;
+}
+
+
+/* ======================================================================== */
+/* libata driver */
+/* ======================================================================== */
+
+static void
+mpc52xx_ata_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct mpc52xx_ata_priv *priv = ap->host->private_data;
+ int pio, rv;
+
+ pio = adev->pio_mode - XFER_PIO_0;
+
+ rv = mpc52xx_ata_compute_pio_timings(priv, adev->devno, pio);
+
+ if (rv) {
+ printk(KERN_ERR DRV_NAME
+ ": Trying to select invalid PIO mode %d\n", pio);
+ return;
+ }
+
+ mpc52xx_ata_apply_timings(priv, adev->devno);
+}
+static void
+mpc52xx_ata_dev_select(struct ata_port *ap, unsigned int device)
+{
+ struct mpc52xx_ata_priv *priv = ap->host->private_data;
+
+ if (device != priv->csel)
+ mpc52xx_ata_apply_timings(priv, device);
+
+ ata_std_dev_select(ap,device);
+}
+
+static void
+mpc52xx_ata_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, ata_std_prereset, ata_std_softreset, NULL,
+ ata_std_postreset);
+}
+
+
+
+static struct scsi_host_template mpc52xx_ata_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .max_sectors = ATA_MAX_SECTORS,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .bios_param = ata_std_bios_param,
+};
+
+static struct ata_port_operations mpc52xx_ata_port_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = mpc52xx_ata_set_piomode,
+ .dev_select = mpc52xx_ata_dev_select,
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = mpc52xx_ata_error_handler,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_mmio_data_xfer,
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_host_stop,
+};
+
+static struct ata_probe_ent mpc52xx_ata_probe_ent = {
+ .port_ops = &mpc52xx_ata_port_ops,
+ .sht = &mpc52xx_ata_sht,
+ .n_ports = 1,
+ .pio_mask = 0x1f, /* Up to PIO4 */
+ .mwdma_mask = 0x00, /* No MWDMA */
+ .udma_mask = 0x00, /* No UDMA */
+ .port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_MMIO,
+ .irq_flags = 0,
+};
+
+static int __devinit
+mpc52xx_ata_init_one(struct device *dev, struct mpc52xx_ata_priv *priv)
+{
+ struct ata_probe_ent *ae = &mpc52xx_ata_probe_ent;
+ struct ata_ioports *aio = &ae->port[0];
+ int rv;
+
+ INIT_LIST_HEAD(&ae->node);
+ ae->dev = dev;
+ ae->irq = priv->ata_irq;
+
+ aio->cmd_addr = 0; /* Don't have a classic reg block */
+ aio->altstatus_addr = (unsigned long)&priv->ata_regs->tf_control;
+ aio->ctl_addr = (unsigned long)&priv->ata_regs->tf_control;
+ aio->data_addr = (unsigned long)&priv->ata_regs->tf_data;
+ aio->error_addr = (unsigned long)&priv->ata_regs->tf_features;
+ aio->feature_addr = (unsigned long)&priv->ata_regs->tf_features;
+ aio->nsect_addr = (unsigned long)&priv->ata_regs->tf_sec_count;
+ aio->lbal_addr = (unsigned long)&priv->ata_regs->tf_sec_num;
+ aio->lbam_addr = (unsigned long)&priv->ata_regs->tf_cyl_low;
+ aio->lbah_addr = (unsigned long)&priv->ata_regs->tf_cyl_high;
+ aio->device_addr = (unsigned long)&priv->ata_regs->tf_dev_head;
+ aio->status_addr = (unsigned long)&priv->ata_regs->tf_command;
+ aio->command_addr = (unsigned long)&priv->ata_regs->tf_command;
+
+ ae->private_data = priv;
+
+ rv = ata_device_add(ae);
+
+ return rv ? 0 : -EINVAL;
+}
+
+static struct mpc52xx_ata_priv *
+mpc52xx_ata_remove_one(struct device *dev)
+{
+ struct ata_host *host = dev_get_drvdata(dev);
+ struct mpc52xx_ata_priv *priv = host->private_data;
+
+ ata_host_remove(host);
+
+ return priv;
+}
+
+
+/* ======================================================================== */
+/* OF Platform driver */
+/* ======================================================================== */
+
+static int __devinit
+mpc52xx_ata_probe(struct of_device *op, const struct of_device_id *match)
+{
+ unsigned int ipb_freq;
+ struct resource res_mem;
+ int ata_irq = NO_IRQ;
+ struct mpc52xx_ata __iomem *ata_regs = NULL;
+ struct mpc52xx_ata_priv *priv = NULL;
+ int rv;
+
+ /* Get ipb frequency */
+ ipb_freq = mpc52xx_find_ipb_freq(op->node);
+ if (!ipb_freq) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Unable to find IPB Bus frequency\n" );
+ return -ENODEV;
+ }
+
+ /* Get IRQ and register */
+ rv = of_address_to_resource(op->node, 0, &res_mem);
+ if (rv) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while parsing device node resource\n" );
+ return rv;
+ }
+
+ ata_irq = irq_of_parse_and_map(op->node, 0);
+ if (ata_irq == NO_IRQ) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while mapping the irq\n");
+ return -EINVAL;
+ }
+
+ /* Request mem region */
+ if (!request_mem_region(res_mem.start,
+ sizeof(struct mpc52xx_ata), DRV_NAME)) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while requesting mem region\n");
+ irq_dispose_mapping(ata_irq);
+ return -EBUSY;
+ }
+
+ /* Remap registers */
+ ata_regs = ioremap(res_mem.start, sizeof(struct mpc52xx_ata));
+ if (!ata_regs) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while mapping register set\n");
+ rv = -ENOMEM;
+ goto err;
+ }
+
+ /* Prepare our private structure */
+ priv = kmalloc(sizeof(struct mpc52xx_ata_priv), GFP_ATOMIC);
+ if (!priv) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while allocating private structure\n");
+ rv = -ENOMEM;
+ goto err;
+ }
+
+ priv->ipb_period = 1000000000 / (ipb_freq / 1000);
+ priv->ata_regs = ata_regs;
+ priv->ata_irq = ata_irq;
+ priv->csel = -1;
+
+ /* Init the hw */
+ rv = mpc52xx_ata_hw_init(priv);
+ if (rv) {
+ printk(KERN_ERR DRV_NAME ": Error during HW init\n");
+ goto err;
+ }
+
+ /* Register ourselves to libata */
+ rv = mpc52xx_ata_init_one(&op->dev, priv);
+ if (rv) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while registering to ATA layer\n");
+ return rv;
+ }
+
+ /* Done */
+ return 0;
+
+ /* Error path */
+err:
+ kfree(priv);
+
+ if (ata_regs)
+ iounmap(ata_regs);
+
+ release_mem_region(res_mem.start, sizeof(struct mpc52xx_ata));
+
+ irq_dispose_mapping(ata_irq);
+
+ return rv;
+}
+
+static int
+mpc52xx_ata_remove(struct of_device *op)
+{
+ struct mpc52xx_ata_priv *priv;
+ struct resource res_mem;
+ int rv;
+
+ /* Unregister */
+ priv = mpc52xx_ata_remove_one(&op->dev);
+
+ /* Free everything */
+ iounmap(priv->ata_regs);
+
+ rv = of_address_to_resource(op->node, 0, &res_mem);
+ if (rv) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while parsing device node resource\n");
+ printk(KERN_ERR DRV_NAME ": "
+ "Zone may not be properly released\n");
+ } else
+ release_mem_region(res_mem.start, sizeof(struct mpc52xx_ata));
+
+ irq_dispose_mapping(priv->ata_irq);
+
+ kfree(priv);
+
+ return 0;
+}
+
+
+#ifdef CONFIG_PM
+
+static int
+mpc52xx_ata_suspend(struct of_device *op, pm_message_t state)
+{
+ return 0; /* FIXME : What to do here ? */
+}
+
+static int
+mpc52xx_ata_resume(struct of_device *op)
+{
+ return 0; /* FIXME : What to do here ? */
+}
+
+#endif
+
+
+static struct of_device_id mpc52xx_ata_of_match[] = {
+ {
+ .compatible = "mpc5200-ata",
+ },
+ {
+ .compatible = "mpc52xx-ata",
+ },
+ {},
+};
+
+
+static struct of_platform_driver mpc52xx_ata_of_platform_driver = {
+ .owner = THIS_MODULE,
+ .name = DRV_NAME,
+ .match_table = mpc52xx_ata_of_match,
+ .probe = mpc52xx_ata_probe,
+ .remove = mpc52xx_ata_remove,
+#ifdef CONFIG_PM
+ .suspend = mpc52xx_ata_suspend,
+ .resume = mpc52xx_ata_resume,
+#endif
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+
+/* ======================================================================== */
+/* Module */
+/* ======================================================================== */
+
+static int __init
+mpc52xx_ata_init(void)
+{
+ printk(KERN_INFO "ata: MPC52xx IDE/ATA libata driver\n");
+ return of_register_platform_driver(&mpc52xx_ata_of_platform_driver);
+}
+
+static void __exit
+mpc52xx_ata_exit(void)
+{
+ of_unregister_platform_driver(&mpc52xx_ata_of_platform_driver);
+}
+
+module_init(mpc52xx_ata_init);
+module_exit(mpc52xx_ata_exit);
+
+MODULE_AUTHOR("Sylvain Munaut <tnt@246tNt.com>");
+MODULE_DESCRIPTION("Freescale MPC52xx IDE/ATA libata driver");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(of, mpc52xx_ata_of_match);
+MODULE_VERSION(DRV_VERSION);
+
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c
index f02b6a3..8019197 100644
--- a/drivers/ata/pata_serverworks.c
+++ b/drivers/ata/pata_serverworks.c
@@ -559,7 +559,7 @@ static int serverworks_reinit_one(struct pci_dev *pdev)
{
/* Force master latency timer to 64 PCI clocks */
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40);
-
+
switch (pdev->device)
{
case PCI_DEVICE_ID_SERVERWORKS_OSB4IDE:
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index 32cf0bf..ae07f63 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -270,7 +270,7 @@ static struct ata_port_operations sil680_port_ops = {
* is powered up on boot and when we resume in case we resumed from RAM.
* Returns the final clock settings.
*/
-
+
static u8 sil680_init_chip(struct pci_dev *pdev)
{
u32 class_rev = 0;
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index 916cedb..c434c4e 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -847,7 +847,7 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
struct sis_chipset *chipset = NULL;
static struct sis_chipset sis_chipsets[] = {
-
+
{ 0x0968, &sis_info133 },
{ 0x0966, &sis_info133 },
{ 0x0965, &sis_info133 },
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index cc09d47..9905fa8 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -384,11 +384,11 @@ static struct ata_port_operations via_port_ops_noirq = {
static void via_config_fifo(struct pci_dev *pdev, unsigned int flags)
{
u8 enable;
-
+
/* 0x40 low bits indicate enabled channels */
pci_read_config_byte(pdev, 0x40 , &enable);
enable &= 3;
-
+
if (flags & VIA_SET_FIFO) {
u8 fifo_setting[4] = {0x00, 0x60, 0x00, 0x20};
u8 fifo;
@@ -509,7 +509,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
/* Initialise the FIFO for the enabled channels. */
via_config_fifo(pdev, config->flags);
-
+
/* Clock set up */
switch(config->flags & VIA_UDMA) {
case VIA_UDMA_NONE:
@@ -568,7 +568,7 @@ static int via_reinit_one(struct pci_dev *pdev)
u32 timing;
struct ata_host *host = dev_get_drvdata(&pdev->dev);
const struct via_isa_bridge *config = host->private_data;
-
+
via_config_fifo(pdev, config->flags);
if ((config->flags & VIA_UDMA) == VIA_UDMA_66) {
@@ -583,7 +583,7 @@ static int via_reinit_one(struct pci_dev *pdev)
timing &= ~0x80008;
pci_write_config_dword(pdev, 0x50, timing);
}
- return ata_pci_device_resume(pdev);
+ return ata_pci_device_resume(pdev);
}
static const struct pci_device_id via[] = {
diff --git a/drivers/ata/pata_winbond.c b/drivers/ata/pata_winbond.c
index 3ea345c..cd5560f 100644
--- a/drivers/ata/pata_winbond.c
+++ b/drivers/ata/pata_winbond.c
@@ -5,7 +5,7 @@
* Support for the Winbond 83759A when operating in advanced mode.
* Multichip mode is not currently supported.
*/
-
+
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
@@ -69,7 +69,7 @@ static void winbond_set_piomode(struct ata_port *ap, struct ata_device *adev)
int timing = 0x88 + (ap->port_no * 4) + (adev->devno * 2);
reg = winbond_readcfg(winbond->config, 0x81);
-
+
/* Get the timing data in cycles */
if (reg & 0x40) /* Fast VLB bus, assume 50MHz */
ata_timing_compute(adev, adev->pio_mode, &t, 20000, 1000);
@@ -80,9 +80,9 @@ static void winbond_set_piomode(struct ata_port *ap, struct ata_device *adev)
recovery = (FIT(t.recover, 1, 15) + 1) & 0x0F;
timing = (active << 4) | recovery;
winbond_writecfg(winbond->config, timing, reg);
-
+
/* Load the setup timing */
-
+
reg = 0x35;
if (adev->class != ATA_DEV_ATA)
reg |= 0x08; /* FIFO off */
@@ -194,13 +194,13 @@ static __init int winbond_init_one(unsigned long port)
winbond_writecfg(port, 0x85, reg);
reg = winbond_readcfg(port, 0x81);
-
+
if (!(reg & 0x03)) /* Disabled */
return 0;
for (i = 0; i < 2 ; i ++) {
- if (reg & (1 << i)) {
+ if (reg & (1 << i)) {
/*
* Fill in a probe structure first of all
*/
@@ -217,7 +217,7 @@ static __init int winbond_init_one(unsigned long port)
ae.pio_mask = 0x1F;
ae.sht = &winbond_sht;
-
+
ae.n_ports = 1;
ae.irq = 14 + i;
ae.irq_flags = 0;
@@ -257,7 +257,7 @@ static __init int winbond_init(void)
int ct = 0;
int i;
-
+
if (probe_winbond == 0)
return -ENODEV;
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 0d316eb..49f8ff2 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -536,7 +536,7 @@ static void nv_adma_mode(struct ata_port *ap)
if (!(pp->flags & NV_ADMA_PORT_REGISTER_MODE))
return;
-
+
WARN_ON(pp->flags & NV_ADMA_ATAPI_SETUP_COMPLETE);
tmp = readw(mmio + NV_ADMA_CTL);
@@ -576,7 +576,7 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
/* Subtract 1 since an extra entry may be needed for padding, see
libata-scsi.c */
sg_tablesize = LIBATA_MAX_PRD - 1;
-
+
/* Since the legacy DMA engine is in use, we need to disable ADMA
on the port. */
adma_enable = 0;
@@ -588,7 +588,7 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
sg_tablesize = NV_ADMA_SGTBL_TOTAL_LEN;
adma_enable = 1;
}
-
+
pci_read_config_dword(pdev, NV_MCP_SATA_CFG_20, ¤t_reg);
if(ap->port_no == 1)
@@ -597,7 +597,7 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
else
config_mask = NV_MCP_SATA_CFG_20_PORT0_EN |
NV_MCP_SATA_CFG_20_PORT0_PWB_EN;
-
+
if(adma_enable) {
new_reg = current_reg | config_mask;
pp->flags &= ~NV_ADMA_ATAPI_SETUP_COMPLETE;
@@ -606,10 +606,10 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
new_reg = current_reg & ~config_mask;
pp->flags |= NV_ADMA_ATAPI_SETUP_COMPLETE;
}
-
+
if(current_reg != new_reg)
pci_write_config_dword(pdev, NV_MCP_SATA_CFG_20, new_reg);
-
+
blk_queue_bounce_limit(sdev->request_queue, bounce_limit);
blk_queue_segment_boundary(sdev->request_queue, segment_boundary);
blk_queue_max_hw_segments(sdev->request_queue, sg_tablesize);
@@ -822,13 +822,13 @@ static irqreturn_t nv_adma_interrupt(int irq, void *dev_instance)
handled++; /* irq handled if we got here */
}
}
-
+
if(notifier_clears[0] || notifier_clears[1]) {
/* Note: Both notifier clear registers must be written
if either is set, even if one is zero, according to NVIDIA. */
- writel(notifier_clears[0],
+ writel(notifier_clears[0],
nv_adma_notifier_clear_block(host->ports[0]));
- writel(notifier_clears[1],
+ writel(notifier_clears[1],
nv_adma_notifier_clear_block(host->ports[1]));
}
diff --git a/drivers/ata/sata_sis.c b/drivers/ata/sata_sis.c
index 9c25a1e..c90fb13 100644
--- a/drivers/ata/sata_sis.c
+++ b/drivers/ata/sata_sis.c
@@ -42,7 +42,7 @@
#include <linux/libata.h>
#define DRV_NAME "sata_sis"
-#define DRV_VERSION "0.6"
+#define DRV_VERSION "0.7"
enum {
sis_180 = 0,
@@ -67,9 +67,12 @@ static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg);
static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static const struct pci_device_id sis_pci_tbl[] = {
- { PCI_VDEVICE(SI, 0x180), sis_180 },
- { PCI_VDEVICE(SI, 0x181), sis_180 },
- { PCI_VDEVICE(SI, 0x182), sis_180 },
+ { PCI_VDEVICE(SI, 0x0180), sis_180 }, /* SiS 964/180 */
+ { PCI_VDEVICE(SI, 0x0181), sis_180 }, /* SiS 964/180 */
+ { PCI_VDEVICE(SI, 0x0182), sis_180 }, /* SiS 965/965L */
+ { PCI_VDEVICE(SI, 0x0183), sis_180 }, /* SiS 965/965L */
+ { PCI_VDEVICE(SI, 0x1182), sis_180 }, /* SiS 966/966L */
+ { PCI_VDEVICE(SI, 0x1183), sis_180 }, /* SiS 966/966L */
{ } /* terminate list */
};
@@ -142,24 +145,32 @@ MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, sis_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-static unsigned int get_scr_cfg_addr(unsigned int port_no, unsigned int sc_reg, int device)
+static unsigned int get_scr_cfg_addr(unsigned int port_no, unsigned int sc_reg, struct pci_dev *pdev)
{
unsigned int addr = SIS_SCR_BASE + (4 * sc_reg);
if (port_no) {
- if (device == 0x182)
- addr += SIS182_SATA1_OFS;
- else
- addr += SIS180_SATA1_OFS;
+ switch (pdev->device) {
+ case 0x0180:
+ case 0x0181:
+ addr += SIS180_SATA1_OFS;
+ break;
+
+ case 0x0182:
+ case 0x0183:
+ case 0x1182:
+ case 0x1183:
+ addr += SIS182_SATA1_OFS;
+ break;
+ }
}
-
return addr;
}
static u32 sis_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, sc_reg, pdev->device);
+ unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, sc_reg, pdev);
u32 val, val2 = 0;
u8 pmr;
@@ -170,7 +181,8 @@ static u32 sis_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
pci_read_config_dword(pdev, cfg_addr, &val);
- if ((pdev->device == 0x182) || (pmr & SIS_PMR_COMBINED))
+ if ((pdev->device == 0x0182) || (pdev->device == 0x0183) || (pdev->device == 0x1182) ||
+ (pdev->device == 0x1183) || (pmr & SIS_PMR_COMBINED))
pci_read_config_dword(pdev, cfg_addr+0x10, &val2);
return (val|val2) & 0xfffffffb; /* avoid problems with powerdowned ports */
@@ -179,7 +191,7 @@ static u32 sis_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
static void sis_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, scr, pdev->device);
+ unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, scr, pdev);
u8 pmr;
if (scr == SCR_ERROR) /* doesn't exist in PCI cfg space */
@@ -189,7 +201,8 @@ static void sis_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val)
pci_write_config_dword(pdev, cfg_addr, val);
- if ((pdev->device == 0x182) || (pmr & SIS_PMR_COMBINED))
+ if ((pdev->device == 0x0182) || (pdev->device == 0x0183) || (pdev->device == 0x1182) ||
+ (pdev->device == 0x1183) || (pmr & SIS_PMR_COMBINED))
pci_write_config_dword(pdev, cfg_addr+0x10, val);
}
@@ -209,7 +222,8 @@ static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg)
val = inl(ap->ioaddr.scr_addr + (sc_reg * 4));
- if ((pdev->device == 0x182) || (pmr & SIS_PMR_COMBINED))
+ if ((pdev->device == 0x0182) || (pdev->device == 0x0183) || (pdev->device == 0x1182) ||
+ (pdev->device == 0x1183) || (pmr & SIS_PMR_COMBINED))
val2 = inl(ap->ioaddr.scr_addr + (sc_reg * 4) + 0x10);
return (val | val2) & 0xfffffffb;
@@ -229,7 +243,8 @@ static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
sis_scr_cfg_write(ap, sc_reg, val);
else {
outl(val, ap->ioaddr.scr_addr + (sc_reg * 4));
- if ((pdev->device == 0x182) || (pmr & SIS_PMR_COMBINED))
+ if ((pdev->device == 0x0182) || (pdev->device == 0x0183) || (pdev->device == 0x1182) ||
+ (pdev->device == 0x1183) || (pmr & SIS_PMR_COMBINED))
outl(val, ap->ioaddr.scr_addr + (sc_reg * 4)+0x10);
}
}
@@ -243,7 +258,7 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
struct ata_port_info pi = sis_port_info, *ppi[2] = { &pi, &pi };
int pci_dev_busy = 0;
u8 pmr;
- u8 port2_start;
+ u8 port2_start = 0x20;
if (!printed_version++)
dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
@@ -282,28 +297,42 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
}
pci_read_config_byte(pdev, SIS_PMR, &pmr);
- if (ent->device != 0x182) {
+ switch (ent->device) {
+ case 0x0180:
+ case 0x0181:
if ((pmr & SIS_PMR_COMBINED) == 0) {
dev_printk(KERN_INFO, &pdev->dev,
"Detected SiS 180/181/964 chipset in SATA mode\n");
port2_start = 64;
- }
- else {
+ } else {
dev_printk(KERN_INFO, &pdev->dev,
"Detected SiS 180/181 chipset in combined mode\n");
port2_start=0;
pi.flags |= ATA_FLAG_SLAVE_POSS;
}
- }
- else {
+ break;
+
+ case 0x0182:
+ case 0x0183:
pci_read_config_dword ( pdev, 0x6C, &val);
if (val & (1L << 31)) {
dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 182/965 chipset\n");
pi.flags |= ATA_FLAG_SLAVE_POSS;
- }
- else
+ } else {
dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 182/965L chipset\n");
- port2_start = 0x20;
+ }
+ break;
+
+ case 0x1182:
+ case 0x1183:
+ pci_read_config_dword(pdev, 0x64, &val);
+ if (val & 0x10000000) {
+ dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 1182/1183/966L SATA controller\n");
+ } else {
+ dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 1182/1183/966 SATA controller\n");
+ pi.flags |= ATA_FLAG_SLAVE_POSS;
+ }
+ break;
}
probe_ent = ata_pci_init_native_mode(pdev, ppi, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY);
diff --git a/drivers/ata/sata_svw.c b/drivers/ata/sata_svw.c
index db32d15..d89c959 100644
--- a/drivers/ata/sata_svw.c
+++ b/drivers/ata/sata_svw.c
@@ -56,6 +56,8 @@
#define DRV_VERSION "2.0"
enum {
+ K2_FLAG_NO_ATAPI_DMA = (1 << 29),
+
/* Taskfile registers offsets */
K2_SATA_TF_CMD_OFFSET = 0x00,
K2_SATA_TF_DATA_OFFSET = 0x00,
@@ -83,11 +85,33 @@ enum {
/* Port stride */
K2_SATA_PORT_OFFSET = 0x100,
+
+ board_svw4 = 0,
+ board_svw8 = 1,
+};
+
+static const struct k2_board_info {
+ unsigned int n_ports;
+ unsigned long port_flags;
+} k2_board_info[] = {
+ /* board_svw4 */
+ { 4, K2_FLAG_NO_ATAPI_DMA },
+
+ /* board_svw8 */
+ { 8, K2_FLAG_NO_ATAPI_DMA },
};
static u8 k2_stat_check_status(struct ata_port *ap);
+static int k2_sata_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+ if (qc->ap->flags & K2_FLAG_NO_ATAPI_DMA)
+ return -1; /* ATAPI DMA not supported */
+
+ return 0;
+}
+
static u32 k2_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
{
if (sc_reg > SCR_CONTROL)
@@ -313,6 +337,7 @@ static const struct ata_port_operations k2_sata_ops = {
.check_status = k2_stat_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
+ .check_atapi_dma = k2_sata_check_atapi_dma,
.bmdma_setup = k2_bmdma_setup_mmio,
.bmdma_start = k2_bmdma_start_mmio,
.bmdma_stop = ata_bmdma_stop,
@@ -359,6 +384,8 @@ static int k2_sata_init_one (struct pci_dev *pdev, const struct pci_device_id *e
struct ata_probe_ent *probe_ent = NULL;
unsigned long base;
void __iomem *mmio_base;
+ const struct k2_board_info *board_info =
+ &k2_board_info[ent->driver_data];
int pci_dev_busy = 0;
int rc;
int i;
@@ -424,7 +451,7 @@ static int k2_sata_init_one (struct pci_dev *pdev, const struct pci_device_id *e
probe_ent->sht = &k2_sata_sht;
probe_ent->port_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_MMIO;
+ ATA_FLAG_MMIO | board_info->port_flags;
probe_ent->port_ops = &k2_sata_ops;
probe_ent->n_ports = 4;
probe_ent->irq = pdev->irq;
@@ -441,7 +468,7 @@ static int k2_sata_init_one (struct pci_dev *pdev, const struct pci_device_id *e
/* different controllers have different number of ports - currently 4 or 8 */
/* All ports are on the same function. Multi-function device is no
* longer available. This should not be seen in any system. */
- for (i = 0; i < ent->driver_data; i++)
+ for (i = 0; i < board_info->n_ports; i++)
k2_sata_setup_port(&probe_ent->port[i], base + i * K2_SATA_PORT_OFFSET);
pci_set_master(pdev);
@@ -469,11 +496,11 @@ err_out:
* controller
* */
static const struct pci_device_id k2_sata_pci_tbl[] = {
- { PCI_VDEVICE(SERVERWORKS, 0x0240), 4 },
- { PCI_VDEVICE(SERVERWORKS, 0x0241), 4 },
- { PCI_VDEVICE(SERVERWORKS, 0x0242), 8 },
- { PCI_VDEVICE(SERVERWORKS, 0x024a), 4 },
- { PCI_VDEVICE(SERVERWORKS, 0x024b), 4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0240), board_svw4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0241), board_svw4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0242), board_svw8 },
+ { PCI_VDEVICE(SERVERWORKS, 0x024a), board_svw4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x024b), board_svw4 },
{ }
};
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index 1c7f19a..8c2335c 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -319,7 +319,7 @@ static struct ata_probe_ent *vt6420_init_probe_ent(struct pci_dev *pdev)
{
struct ata_probe_ent *probe_ent;
struct ata_port_info *ppi[2];
-
+
ppi[0] = ppi[1] = &vt6420_port_info;
probe_ent = ata_pci_init_native_mode(pdev, ppi, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY);
if (!probe_ent)
diff --git a/include/linux/libata.h b/include/linux/libata.h
index ab27548..9356322 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -307,7 +307,7 @@ enum {
* most devices.
*/
ATA_SPINUP_WAIT = 8000,
-
+
/* Horkage types. May be set by libata or controller on drives
(some horkage may be drive/controller pair dependant */
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 95c1e74..ff9e6d3 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -1621,6 +1621,7 @@
#define PCI_VENDOR_ID_ITE 0x1283
#define PCI_DEVICE_ID_ITE_8211 0x8211
#define PCI_DEVICE_ID_ITE_8212 0x8212
+#define PCI_DEVICE_ID_ITE_8213 0x8213
#define PCI_DEVICE_ID_ITE_8872 0x8872
#define PCI_DEVICE_ID_ITE_IT8330G_0 0xe886
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2006-12-07 12:40 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2006-12-07 12:40 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
drivers/ata/libata-core.c | 3 +
drivers/ata/sata_promise.c | 120 ++++++++++++++++++++++++++++----------------
2 files changed, 79 insertions(+), 44 deletions(-)
Alan:
libata: Incorrect timing computation for PIO5/6
Albert Lee:
libata: let ATA_FLAG_PIO_POLLING use polling pio for ATA_PROT_NODATA
Mikael Pettersson:
sata_promise: cleanups, take 2
sata_promise: new EH conversion, take 2
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 8816e30..011c0a8 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -2303,7 +2303,7 @@ int ata_timing_compute(struct ata_device
* DMA cycle timing is slower/equal than the fastest PIO timing.
*/
- if (speed > XFER_PIO_4) {
+ if (speed > XFER_PIO_6) {
ata_timing_compute(adev, adev->pio_mode, &p, T, UT);
ata_timing_merge(&p, t, t, ATA_TIMING_ALL);
}
@@ -4960,6 +4960,7 @@ unsigned int ata_qc_issue_prot(struct at
if (ap->flags & ATA_FLAG_PIO_POLLING) {
switch (qc->tf.protocol) {
case ATA_PROT_PIO:
+ case ATA_PROT_NODATA:
case ATA_PROT_ATAPI:
case ATA_PROT_ATAPI_NODATA:
qc->tf.flags |= ATA_TFLAG_POLLING;
diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c
index a2778cf..f055874 100644
--- a/drivers/ata/sata_promise.c
+++ b/drivers/ata/sata_promise.c
@@ -66,15 +66,17 @@ enum {
board_2037x = 0, /* FastTrak S150 TX2plus */
board_20319 = 1, /* FastTrak S150 TX4 */
board_20619 = 2, /* FastTrak TX4000 */
- board_20771 = 3, /* FastTrak TX2300 */
- board_2057x = 4, /* SATAII150 Tx2plus */
- board_40518 = 5, /* SATAII150 Tx4 */
+ board_2057x = 3, /* SATAII150 Tx2plus */
+ board_40518 = 4, /* SATAII150 Tx4 */
PDC_HAS_PATA = (1 << 1), /* PDC20375/20575 has PATA */
+ /* PDC_CTLSTAT bit definitions */
+ PDC_DMA_ENABLE = (1 << 7),
+ PDC_IRQ_DISABLE = (1 << 10),
PDC_RESET = (1 << 11), /* HDMA reset */
- PDC_COMMON_FLAGS = ATA_FLAG_NO_LEGACY | ATA_FLAG_SRST |
+ PDC_COMMON_FLAGS = ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI |
ATA_FLAG_PIO_POLLING,
@@ -90,7 +92,6 @@ struct pdc_port_priv {
struct pdc_host_priv {
unsigned long flags;
- int hotplug_offset;
};
static u32 pdc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg);
@@ -101,13 +102,16 @@ static void pdc_eng_timeout(struct ata_p
static int pdc_port_start(struct ata_port *ap);
static void pdc_port_stop(struct ata_port *ap);
static void pdc_pata_phy_reset(struct ata_port *ap);
-static void pdc_sata_phy_reset(struct ata_port *ap);
static void pdc_qc_prep(struct ata_queued_cmd *qc);
static void pdc_tf_load_mmio(struct ata_port *ap, const struct ata_taskfile *tf);
static void pdc_exec_command_mmio(struct ata_port *ap, const struct ata_taskfile *tf);
static void pdc_irq_clear(struct ata_port *ap);
static unsigned int pdc_qc_issue_prot(struct ata_queued_cmd *qc);
static void pdc_host_stop(struct ata_host *host);
+static void pdc_freeze(struct ata_port *ap);
+static void pdc_thaw(struct ata_port *ap);
+static void pdc_error_handler(struct ata_port *ap);
+static void pdc_post_internal_cmd(struct ata_queued_cmd *qc);
static struct scsi_host_template pdc_ata_sht = {
@@ -136,11 +140,12 @@ static const struct ata_port_operations
.exec_command = pdc_exec_command_mmio,
.dev_select = ata_std_dev_select,
- .phy_reset = pdc_sata_phy_reset,
-
.qc_prep = pdc_qc_prep,
.qc_issue = pdc_qc_issue_prot,
- .eng_timeout = pdc_eng_timeout,
+ .freeze = pdc_freeze,
+ .thaw = pdc_thaw,
+ .error_handler = pdc_error_handler,
+ .post_internal_cmd = pdc_post_internal_cmd,
.data_xfer = ata_mmio_data_xfer,
.irq_handler = pdc_interrupt,
.irq_clear = pdc_irq_clear,
@@ -198,23 +203,13 @@ static const struct ata_port_info pdc_po
/* board_20619 */
{
.sht = &pdc_ata_sht,
- .flags = PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS,
+ .flags = PDC_COMMON_FLAGS | ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = 0x7f, /* udma0-6 ; FIXME */
.port_ops = &pdc_pata_ops,
},
- /* board_20771 */
- {
- .sht = &pdc_ata_sht,
- .flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 ; FIXME */
- .port_ops = &pdc_sata_ops,
- },
-
/* board_2057x */
{
.sht = &pdc_ata_sht,
@@ -244,6 +239,7 @@ static const struct pci_device_id pdc_at
{ PCI_VDEVICE(PROMISE, 0x3570), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3571), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3574), board_2057x },
+ { PCI_VDEVICE(PROMISE, 0x3577), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3d73), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3d75), board_2057x },
@@ -256,15 +252,6 @@ static const struct pci_device_id pdc_at
{ PCI_VDEVICE(PROMISE, 0x6629), board_20619 },
-/* TODO: remove all associated board_20771 code, as it completely
- * duplicates board_2037x code, unless reason for separation can be
- * divined.
- */
-#if 0
- { PCI_VDEVICE(PROMISE, 0x3570), board_20771 },
-#endif
- { PCI_VDEVICE(PROMISE, 0x3577), board_20771 },
-
{ } /* terminate list */
};
@@ -366,12 +353,6 @@ static void pdc_reset_port(struct ata_po
readl(mmio); /* flush */
}
-static void pdc_sata_phy_reset(struct ata_port *ap)
-{
- pdc_reset_port(ap);
- sata_phy_reset(ap);
-}
-
static void pdc_pata_cbl_detect(struct ata_port *ap)
{
u8 tmp;
@@ -439,6 +420,61 @@ static void pdc_qc_prep(struct ata_queue
}
}
+static void pdc_freeze(struct ata_port *ap)
+{
+ void __iomem *mmio = (void __iomem *) ap->ioaddr.cmd_addr;
+ u32 tmp;
+
+ tmp = readl(mmio + PDC_CTLSTAT);
+ tmp |= PDC_IRQ_DISABLE;
+ tmp &= ~PDC_DMA_ENABLE;
+ writel(tmp, mmio + PDC_CTLSTAT);
+ readl(mmio + PDC_CTLSTAT); /* flush */
+}
+
+static void pdc_thaw(struct ata_port *ap)
+{
+ void __iomem *mmio = (void __iomem *) ap->ioaddr.cmd_addr;
+ u32 tmp;
+
+ /* clear IRQ */
+ readl(mmio + PDC_INT_SEQMASK);
+
+ /* turn IRQ back on */
+ tmp = readl(mmio + PDC_CTLSTAT);
+ tmp &= ~PDC_IRQ_DISABLE;
+ writel(tmp, mmio + PDC_CTLSTAT);
+ readl(mmio + PDC_CTLSTAT); /* flush */
+}
+
+static void pdc_error_handler(struct ata_port *ap)
+{
+ ata_reset_fn_t hardreset;
+
+ if (!(ap->pflags & ATA_PFLAG_FROZEN))
+ pdc_reset_port(ap);
+
+ hardreset = NULL;
+ if (sata_scr_valid(ap))
+ hardreset = sata_std_hardreset;
+
+ /* perform recovery */
+ ata_do_eh(ap, ata_std_prereset, ata_std_softreset, hardreset,
+ ata_std_postreset);
+}
+
+static void pdc_post_internal_cmd(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+
+ if (qc->flags & ATA_QCFLAG_FAILED)
+ qc->err_mask |= AC_ERR_OTHER;
+
+ /* make DMA engine forget about the failed command */
+ if (qc->err_mask)
+ pdc_reset_port(ap);
+}
+
static void pdc_eng_timeout(struct ata_port *ap)
{
struct ata_host *host = ap->host;
@@ -645,9 +681,14 @@ static void pdc_host_init(unsigned int c
{
void __iomem *mmio = pe->mmio_base;
struct pdc_host_priv *hp = pe->private_data;
- int hotplug_offset = hp->hotplug_offset;
+ int hotplug_offset;
u32 tmp;
+ if (hp->flags & PDC_FLAG_GEN_II)
+ hotplug_offset = PDC2_SATA_PLUG_CSR;
+ else
+ hotplug_offset = PDC_SATA_PLUG_CSR;
+
/*
* Except for the hotplug stuff, this is voodoo from the
* Promise driver. Label this entire section
@@ -742,8 +783,6 @@ static int pdc_ata_init_one (struct pci_
goto err_out_free_ent;
}
- /* Set default hotplug offset */
- hp->hotplug_offset = PDC_SATA_PLUG_CSR;
probe_ent->private_data = hp;
probe_ent->sht = pdc_port_info[board_idx].sht;
@@ -767,8 +806,6 @@ static int pdc_ata_init_one (struct pci_
switch (board_idx) {
case board_40518:
hp->flags |= PDC_FLAG_GEN_II;
- /* Override hotplug offset for SATAII150 */
- hp->hotplug_offset = PDC2_SATA_PLUG_CSR;
/* Fall through */
case board_20319:
probe_ent->n_ports = 4;
@@ -780,10 +817,7 @@ static int pdc_ata_init_one (struct pci_
probe_ent->port[3].scr_addr = base + 0x700;
break;
case board_2057x:
- case board_20771:
hp->flags |= PDC_FLAG_GEN_II;
- /* Override hotplug offset for SATAII150 */
- hp->hotplug_offset = PDC2_SATA_PLUG_CSR;
/* Fall through */
case board_2037x:
probe_ent->n_ports = 2;
^ permalink raw reply related [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2006-10-04 11:47 ` Alan Cox
@ 2006-10-04 14:34 ` Alan Cox
0 siblings, 0 replies; 95+ messages in thread
From: Alan Cox @ 2006-10-04 14:34 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Andrew Morton, Linus Torvalds, linux-ide, LKML
Ar Mer, 2006-10-04 am 12:47 +0100, ysgrifennodd Alan Cox:
> Ar Mer, 2006-10-04 am 02:02 -0400, ysgrifennodd Jeff Garzik:
> > Final libata batch for 2.6.19. Meant to send this a couple days ago.
> >
> > Nothing interesting: minor bugfix, some cleanups, improved diagnostics.
>
> Please also include the following. The first fixes support for rev c8 of
> the ALi/ULi PATA. The second keeps pcmcia in sync so ide_cs and
> pata_pcmcia are interchangable, both are only changes to constants.
>
> Right now rev 0xC8 and higher don't work with libata but 0xc8 is in the
> field now.
Forgot
Signed-off-by: Alan Cox <alan@redhat.com>
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2006-10-04 6:02 Jeff Garzik
@ 2006-10-04 11:47 ` Alan Cox
2006-10-04 14:34 ` Alan Cox
0 siblings, 1 reply; 95+ messages in thread
From: Alan Cox @ 2006-10-04 11:47 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Andrew Morton, Linus Torvalds, linux-ide, LKML
Ar Mer, 2006-10-04 am 02:02 -0400, ysgrifennodd Jeff Garzik:
> Final libata batch for 2.6.19. Meant to send this a couple days ago.
>
> Nothing interesting: minor bugfix, some cleanups, improved diagnostics.
Please also include the following. The first fixes support for rev c8 of
the ALi/ULi PATA. The second keeps pcmcia in sync so ide_cs and
pata_pcmcia are interchangable, both are only changes to constants.
Right now rev 0xC8 and higher don't work with libata but 0xc8 is in the
field now.
diff -u --new-file --recursive --exclude-from /usr/src/exclude linux.vanilla-2.6.18-mm3/drivers/ata/pata_ali.c linux-2.6.18-mm3/drivers/ata/pata_ali.c
--- linux.vanilla-2.6.18-mm3/drivers/ata/pata_ali.c 2006-10-03 19:23:02.000000000 +0100
+++ linux-2.6.18-mm3/drivers/ata/pata_ali.c 2006-10-03 23:26:09.000000000 +0100
@@ -34,7 +34,7 @@
#include <linux/dmi.h>
#define DRV_NAME "pata_ali"
-#define DRV_VERSION "0.6.5"
+#define DRV_VERSION "0.6.6"
/*
* Cable special cases
@@ -630,7 +630,7 @@
pci_read_config_byte(pdev, 0x53, &tmp);
if (rev <= 0x20)
tmp &= ~0x02;
- if (rev == 0xc7)
+ if (rev >= 0xc7)
tmp |= 0x03;
else
tmp |= 0x01; /* CD_ROM enable for DMA */
diff -u --new-file --recursive --exclude-from /usr/src/exclude linux.vanilla-2.6.18-mm3/drivers/ata/pata_pcmcia.c linux-2.6.18-mm3/drivers/ata/pata_pcmcia.c
--- linux.vanilla-2.6.18-mm3/drivers/ata/pata_pcmcia.c 2006-10-03 19:23:02.000000000 +0100
+++ linux-2.6.18-mm3/drivers/ata/pata_pcmcia.c 2006-09-28 15:24:37.000000000 +0100
@@ -42,7 +42,7 @@
#define DRV_NAME "pata_pcmcia"
-#define DRV_VERSION "0.2.9"
+#define DRV_VERSION "0.2.11"
/*
* Private data structure to glue stuff together
@@ -355,6 +355,8 @@
PCMCIA_DEVICE_PROD_ID12("SAMSUNG", "04/05/06", 0x43d74cb4, 0x6a22777d),
PCMCIA_DEVICE_PROD_ID12("SMI VENDOR", "SMI PRODUCT", 0x30896c92, 0x703cc5f6),
PCMCIA_DEVICE_PROD_ID12("TOSHIBA", "MK2001MPL", 0xb4585a1a, 0x3489e003),
+ PCMCIA_DEVICE_PROD_ID1("TRANSCEND 512M ", 0xd0909443),
+ PCMCIA_DEVICE_PROD_ID12("TRANSCEND", "TS4GCF120", 0x709b1bf1, 0xf54a91c8),
PCMCIA_DEVICE_PROD_ID12("WIT", "IDE16", 0x244e5994, 0x3e232852),
PCMCIA_DEVICE_PROD_ID1("STI Flash", 0xe4a13209),
PCMCIA_DEVICE_PROD_ID12("STI", "Flash 5.0", 0xbf2df18d, 0x8cb57a0e),
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2006-10-04 6:02 Jeff Garzik
2006-10-04 11:47 ` Alan Cox
0 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2006-10-04 6:02 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
Final libata batch for 2.6.19. Meant to send this a couple days ago.
Nothing interesting: minor bugfix, some cleanups, improved diagnostics.
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
Documentation/DocBook/libata.tmpl | 2 -
drivers/ata/ahci.c | 90 ++++++++++++-------------------------
drivers/ata/libata-core.c | 12 +++--
drivers/ata/libata-scsi.c | 14 +++++-
drivers/ata/libata-sff.c | 44 +++++++++---------
drivers/ata/pata_ali.c | 9 ++--
drivers/ata/pata_amd.c | 38 ++++++++--------
drivers/ata/pata_artop.c | 17 ++++---
drivers/ata/pata_atiixp.c | 14 +++---
drivers/ata/pata_cmd64x.c | 17 +++----
drivers/ata/pata_cs5520.c | 10 ++--
drivers/ata/pata_cs5530.c | 11 ++---
drivers/ata/pata_cs5535.c | 9 ++--
drivers/ata/pata_cypress.c | 13 +++--
drivers/ata/pata_efar.c | 4 +-
drivers/ata/pata_hpt366.c | 9 ++--
drivers/ata/pata_hpt37x.c | 19 ++++----
drivers/ata/pata_hpt3x2n.c | 17 +++----
drivers/ata/pata_hpt3x3.c | 9 ++--
drivers/ata/pata_it821x.c | 13 ++---
drivers/ata/pata_jmicron.c | 11 ++---
drivers/ata/pata_mpiix.c | 9 +---
drivers/ata/pata_netcell.c | 3 +
drivers/ata/pata_ns87410.c | 9 ++--
drivers/ata/pata_oldpiix.c | 4 +-
drivers/ata/pata_opti.c | 10 ++--
drivers/ata/pata_optidma.c | 9 ++--
drivers/ata/pata_pdc2027x.c | 15 +++---
drivers/ata/pata_pdc202xx_old.c | 19 ++++----
drivers/ata/pata_radisys.c | 4 +-
drivers/ata/pata_rz1000.c | 12 ++---
drivers/ata/pata_sc1200.c | 11 ++---
drivers/ata/pata_serverworks.c | 17 +++----
drivers/ata/pata_sil680.c | 9 ++--
drivers/ata/pata_sis.c | 6 +-
drivers/ata/pata_sl82c105.c | 9 ++--
drivers/ata/pata_triflex.c | 10 ++--
drivers/ata/pata_via.c | 15 +++---
drivers/ata/pdc_adma.c | 3 -
drivers/ata/sata_mv.c | 27 ++++++-----
drivers/ata/sata_nv.c | 53 ++++++++--------------
drivers/ata/sata_promise.c | 55 ++++++++---------------
drivers/ata/sata_qstor.c | 3 -
drivers/ata/sata_sil.c | 15 +++---
drivers/ata/sata_sil24.c | 11 ++---
drivers/ata/sata_sis.c | 8 ++-
drivers/ata/sata_svw.c | 15 ++----
drivers/ata/sata_sx4.c | 5 +-
drivers/ata/sata_uli.c | 8 ++-
drivers/ata/sata_via.c | 6 +-
drivers/ata/sata_vsc.c | 6 --
include/linux/libata.h | 9 +++-
52 files changed, 359 insertions(+), 418 deletions(-)
Dave Jones:
Fix reference of uninitialised memory in ata_device_add()
Jeff Garzik:
[libata] Use new PCI_VDEVICE() macro to dramatically shorten ID lists
[libata] minor PCI IDE probe fixes and cleanups
[libata] init probe_ent->private_data in a common location
[libata] Print out Status register, if a BSY-sleep takes too long
[libata] PCI ID table cleanup in various drivers
[libata] DocBook minor updates, fixes
[libata] pata_artop: kill gcc warning
Tejun Heo:
libata: cosmetic changes to constants
libata: turn off NCQ if queue depth is adjusted to 1
diff --git a/Documentation/DocBook/libata.tmpl b/Documentation/DocBook/libata.tmpl
index 065e8dc..f9a7c06 100644
--- a/Documentation/DocBook/libata.tmpl
+++ b/Documentation/DocBook/libata.tmpl
@@ -14,7 +14,7 @@
</authorgroup>
<copyright>
- <year>2003-2005</year>
+ <year>2003-2006</year>
<holder>Jeff Garzik</holder>
</copyright>
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 1aabc81..54e1f38 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -299,76 +299,46 @@ static const struct ata_port_info ahci_p
static const struct pci_device_id ahci_pci_tbl[] = {
/* Intel */
- { PCI_VENDOR_ID_INTEL, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ICH6 */
- { PCI_VENDOR_ID_INTEL, 0x2653, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ICH6M */
- { PCI_VENDOR_ID_INTEL, 0x27c1, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ICH7 */
- { PCI_VENDOR_ID_INTEL, 0x27c5, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ICH7M */
- { PCI_VENDOR_ID_INTEL, 0x27c3, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ICH7R */
- { PCI_VENDOR_ID_AL, 0x5288, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ULi M5288 */
- { PCI_VENDOR_ID_INTEL, 0x2681, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ESB2 */
- { PCI_VENDOR_ID_INTEL, 0x2682, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ESB2 */
- { PCI_VENDOR_ID_INTEL, 0x2683, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ESB2 */
- { PCI_VENDOR_ID_INTEL, 0x27c6, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ICH7-M DH */
- { PCI_VENDOR_ID_INTEL, 0x2821, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ICH8 */
- { PCI_VENDOR_ID_INTEL, 0x2822, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ICH8 */
- { PCI_VENDOR_ID_INTEL, 0x2824, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ICH8 */
- { PCI_VENDOR_ID_INTEL, 0x2829, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ICH8M */
- { PCI_VENDOR_ID_INTEL, 0x282a, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ICH8M */
+ { PCI_VDEVICE(INTEL, 0x2652), board_ahci }, /* ICH6 */
+ { PCI_VDEVICE(INTEL, 0x2653), board_ahci }, /* ICH6M */
+ { PCI_VDEVICE(INTEL, 0x27c1), board_ahci }, /* ICH7 */
+ { PCI_VDEVICE(INTEL, 0x27c5), board_ahci }, /* ICH7M */
+ { PCI_VDEVICE(INTEL, 0x27c3), board_ahci }, /* ICH7R */
+ { PCI_VDEVICE(AL, 0x5288), board_ahci }, /* ULi M5288 */
+ { PCI_VDEVICE(INTEL, 0x2681), board_ahci }, /* ESB2 */
+ { PCI_VDEVICE(INTEL, 0x2682), board_ahci }, /* ESB2 */
+ { PCI_VDEVICE(INTEL, 0x2683), board_ahci }, /* ESB2 */
+ { PCI_VDEVICE(INTEL, 0x27c6), board_ahci }, /* ICH7-M DH */
+ { PCI_VDEVICE(INTEL, 0x2821), board_ahci }, /* ICH8 */
+ { PCI_VDEVICE(INTEL, 0x2822), board_ahci }, /* ICH8 */
+ { PCI_VDEVICE(INTEL, 0x2824), board_ahci }, /* ICH8 */
+ { PCI_VDEVICE(INTEL, 0x2829), board_ahci }, /* ICH8M */
+ { PCI_VDEVICE(INTEL, 0x282a), board_ahci }, /* ICH8M */
/* JMicron */
- { 0x197b, 0x2360, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* JMicron JMB360 */
- { 0x197b, 0x2361, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* JMicron JMB361 */
- { 0x197b, 0x2363, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* JMicron JMB363 */
- { 0x197b, 0x2365, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* JMicron JMB365 */
- { 0x197b, 0x2366, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* JMicron JMB366 */
+ { PCI_VDEVICE(JMICRON, 0x2360), board_ahci }, /* JMicron JMB360 */
+ { PCI_VDEVICE(JMICRON, 0x2361), board_ahci }, /* JMicron JMB361 */
+ { PCI_VDEVICE(JMICRON, 0x2363), board_ahci }, /* JMicron JMB363 */
+ { PCI_VDEVICE(JMICRON, 0x2365), board_ahci }, /* JMicron JMB365 */
+ { PCI_VDEVICE(JMICRON, 0x2366), board_ahci }, /* JMicron JMB366 */
/* ATI */
- { PCI_VENDOR_ID_ATI, 0x4380, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ATI SB600 non-raid */
- { PCI_VENDOR_ID_ATI, 0x4381, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* ATI SB600 raid */
+ { PCI_VDEVICE(ATI, 0x4380), board_ahci }, /* ATI SB600 non-raid */
+ { PCI_VDEVICE(ATI, 0x4381), board_ahci }, /* ATI SB600 raid */
/* VIA */
- { PCI_VENDOR_ID_VIA, 0x3349, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci_vt8251 }, /* VIA VT8251 */
+ { PCI_VDEVICE(VIA, 0x3349), board_ahci_vt8251 }, /* VIA VT8251 */
/* NVIDIA */
- { PCI_VENDOR_ID_NVIDIA, 0x044c, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* MCP65 */
- { PCI_VENDOR_ID_NVIDIA, 0x044d, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* MCP65 */
- { PCI_VENDOR_ID_NVIDIA, 0x044e, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* MCP65 */
- { PCI_VENDOR_ID_NVIDIA, 0x044f, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* MCP65 */
+ { PCI_VDEVICE(NVIDIA, 0x044c), board_ahci }, /* MCP65 */
+ { PCI_VDEVICE(NVIDIA, 0x044d), board_ahci }, /* MCP65 */
+ { PCI_VDEVICE(NVIDIA, 0x044e), board_ahci }, /* MCP65 */
+ { PCI_VDEVICE(NVIDIA, 0x044f), board_ahci }, /* MCP65 */
/* SiS */
- { PCI_VENDOR_ID_SI, 0x1184, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* SiS 966 */
- { PCI_VENDOR_ID_SI, 0x1185, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* SiS 966 */
- { PCI_VENDOR_ID_SI, 0x0186, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_ahci }, /* SiS 968 */
+ { PCI_VDEVICE(SI, 0x1184), board_ahci }, /* SiS 966 */
+ { PCI_VDEVICE(SI, 0x1185), board_ahci }, /* SiS 966 */
+ { PCI_VDEVICE(SI, 0x0186), board_ahci }, /* SiS 968 */
{ } /* terminate list */
};
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index b4abd68..dce6565 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -2340,7 +2340,8 @@ unsigned int ata_busy_sleep (struct ata_
if (status & ATA_BUSY)
ata_port_printk(ap, KERN_WARNING,
- "port is slow to respond, please be patient\n");
+ "port is slow to respond, please be patient "
+ "(Status 0x%x)\n", status);
timeout = timer_start + tmout;
while ((status & ATA_BUSY) && (time_before(jiffies, timeout))) {
@@ -2350,7 +2351,8 @@ unsigned int ata_busy_sleep (struct ata_
if (status & ATA_BUSY) {
ata_port_printk(ap, KERN_ERR, "port failed to respond "
- "(%lu secs)\n", tmout / HZ);
+ "(%lu secs, Status 0x%x)\n",
+ tmout / HZ, status);
return 1;
}
@@ -5478,11 +5480,10 @@ int ata_device_add(const struct ata_prob
int irq_line = ent->irq;
ap = ata_port_add(ent, host, i);
+ host->ports[i] = ap;
if (!ap)
goto err_out;
- host->ports[i] = ap;
-
/* dummy? */
if (ent->dummy_port_mask & (1 << i)) {
ata_port_printk(ap, KERN_INFO, "DUMMY\n");
@@ -5740,7 +5741,7 @@ void ata_host_remove(struct ata_host *ho
/**
* ata_scsi_release - SCSI layer callback hook for host unload
- * @host: libata host to be unloaded
+ * @shost: libata host to be unloaded
*
* Performs all duties necessary to shut down a libata port...
* Kill port kthread, disable port, and release resources.
@@ -5786,6 +5787,7 @@ ata_probe_ent_alloc(struct device *dev,
probe_ent->mwdma_mask = port->mwdma_mask;
probe_ent->udma_mask = port->udma_mask;
probe_ent->port_ops = port->port_ops;
+ probe_ent->private_data = port->private_data;
return probe_ent;
}
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 3986ec8..b0d0cc4 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -889,6 +889,7 @@ int ata_scsi_change_queue_depth(struct s
{
struct ata_port *ap = ata_shost_to_port(sdev->host);
struct ata_device *dev;
+ unsigned long flags;
int max_depth;
if (queue_depth < 1)
@@ -904,6 +905,14 @@ int ata_scsi_change_queue_depth(struct s
queue_depth = max_depth;
scsi_adjust_queue_depth(sdev, MSG_SIMPLE_TAG, queue_depth);
+
+ spin_lock_irqsave(ap->lock, flags);
+ if (queue_depth > 1)
+ dev->flags &= ~ATA_DFLAG_NCQ_OFF;
+ else
+ dev->flags |= ATA_DFLAG_NCQ_OFF;
+ spin_unlock_irqrestore(ap->lock, flags);
+
return queue_depth;
}
@@ -1293,7 +1302,8 @@ static unsigned int ata_scsi_rw_xlat(str
*/
goto nothing_to_do;
- if ((dev->flags & (ATA_DFLAG_PIO | ATA_DFLAG_NCQ)) == ATA_DFLAG_NCQ) {
+ if ((dev->flags & (ATA_DFLAG_PIO | ATA_DFLAG_NCQ_OFF |
+ ATA_DFLAG_NCQ)) == ATA_DFLAG_NCQ) {
/* yay, NCQ */
if (!lba_48_ok(block, n_block))
goto out_of_range;
@@ -3174,7 +3184,7 @@ void ata_scsi_dev_rescan(void *data)
/**
* ata_sas_port_alloc - Allocate port for a SAS attached SATA device
- * @pdev: PCI device that the scsi device is attached to
+ * @host: ATA host container for all SAS ports
* @port_info: Information from low-level host driver
* @shost: SCSI host that the scsi device is attached to
*
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index 08b3a40..06daaa3 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -828,7 +828,6 @@ ata_pci_init_native_mode(struct pci_dev
probe_ent->irq = pdev->irq;
probe_ent->irq_flags = IRQF_SHARED;
- probe_ent->private_data = port[0]->private_data;
if (ports & ATA_PORT_PRIMARY) {
probe_ent->port[p].cmd_addr = pci_resource_start(pdev, 0);
@@ -878,7 +877,6 @@ static struct ata_probe_ent *ata_pci_ini
return NULL;
probe_ent->n_ports = 2;
- probe_ent->private_data = port[0]->private_data;
if (port_mask & ATA_PORT_PRIMARY) {
probe_ent->irq = ATA_PRIMARY_IRQ;
@@ -908,6 +906,8 @@ static struct ata_probe_ent *ata_pci_ini
probe_ent->_host_flags |= ATA_HOST_SIMPLEX;
}
ata_std_ports(&probe_ent->port[1]);
+
+ /* FIXME: could be pointing to stack area; must copy */
probe_ent->pinfo2 = port[1];
} else
probe_ent->dummy_port_mask |= ATA_PORT_SECONDARY;
@@ -946,35 +946,21 @@ int ata_pci_init_one (struct pci_dev *pd
{
struct ata_probe_ent *probe_ent = NULL;
struct ata_port_info *port[2];
- u8 tmp8, mask;
+ u8 mask;
unsigned int legacy_mode = 0;
int disable_dev_on_err = 1;
int rc;
DPRINTK("ENTER\n");
+ BUG_ON(n_ports < 1 || n_ports > 2);
+
port[0] = port_info[0];
if (n_ports > 1)
port[1] = port_info[1];
else
port[1] = port[0];
- if ((port[0]->flags & ATA_FLAG_NO_LEGACY) == 0
- && (pdev->class >> 8) == PCI_CLASS_STORAGE_IDE) {
- /* TODO: What if one channel is in native mode ... */
- pci_read_config_byte(pdev, PCI_CLASS_PROG, &tmp8);
- mask = (1 << 2) | (1 << 0);
- if ((tmp8 & mask) != mask)
- legacy_mode = (1 << 3);
- }
-
- /* FIXME... */
- if ((!legacy_mode) && (n_ports > 2)) {
- printk(KERN_ERR "ata: BUG: native mode, n_ports > 2\n");
- n_ports = 2;
- /* For now */
- }
-
/* FIXME: Really for ATA it isn't safe because the device may be
multi-purpose and we want to leave it alone if it was already
enabled. Secondly for shared use as Arjan says we want refcounting
@@ -987,6 +973,16 @@ int ata_pci_init_one (struct pci_dev *pd
if (rc)
return rc;
+ if ((pdev->class >> 8) == PCI_CLASS_STORAGE_IDE) {
+ u8 tmp8;
+
+ /* TODO: What if one channel is in native mode ... */
+ pci_read_config_byte(pdev, PCI_CLASS_PROG, &tmp8);
+ mask = (1 << 2) | (1 << 0);
+ if ((tmp8 & mask) != mask)
+ legacy_mode = (1 << 3);
+ }
+
rc = pci_request_regions(pdev, DRV_NAME);
if (rc) {
disable_dev_on_err = 0;
@@ -1039,7 +1035,7 @@ int ata_pci_init_one (struct pci_dev *pd
goto err_out_regions;
}
- /* FIXME: If we get no DMA mask we should fall back to PIO */
+ /* TODO: If we get no DMA mask we should fall back to PIO */
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
goto err_out_regions;
@@ -1062,13 +1058,17 @@ int ata_pci_init_one (struct pci_dev *pd
pci_set_master(pdev);
- /* FIXME: check ata_device_add return */
- ata_device_add(probe_ent);
+ if (!ata_device_add(probe_ent)) {
+ rc = -ENODEV;
+ goto err_out_ent;
+ }
kfree(probe_ent);
return 0;
+err_out_ent:
+ kfree(probe_ent);
err_out_regions:
if (legacy_mode & ATA_PORT_PRIMARY)
release_region(ATA_PRIMARY_CMD, 8);
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index 87af3b5..3f49e38 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -644,10 +644,11 @@ static int ali_init_one(struct pci_dev *
return ata_pci_init_one(pdev, port_info, 2);
}
-static struct pci_device_id ali[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5228), },
- { PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5229), },
- { 0, },
+static const struct pci_device_id ali[] = {
+ { PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5228), },
+ { PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5229), },
+
+ { },
};
static struct pci_driver ali_pci_driver = {
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index 599ee26..29234c8 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -662,27 +662,28 @@ static int amd_init_one(struct pci_dev *
}
static const struct pci_device_id amd[] = {
- { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_COBRA_7401, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7409, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1 },
- { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7411, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3 },
- { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_OPUS_7441, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
- { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 7 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
- { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 9 },
- { 0, },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_COBRA_7401), 0 },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_VIPER_7409), 1 },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_VIPER_7411), 3 },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_OPUS_7441), 4 },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_8111_IDE), 5 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_IDE), 7 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE), 8 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE), 8 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE), 8 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE), 8 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE), 8 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE), 8 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE), 8 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE), 8 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE), 8 },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_CS5536_IDE), 9 },
+
+ { },
};
static struct pci_driver amd_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = amd,
.probe = amd_init_one,
.remove = ata_pci_remove_one
@@ -698,7 +699,6 @@ static void __exit amd_exit(void)
pci_unregister_driver(&amd_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for AMD PATA IDE");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
index c4ccb75..690828e 100644
--- a/drivers/ata/pata_artop.c
+++ b/drivers/ata/pata_artop.c
@@ -426,7 +426,7 @@ static int artop_init_one (struct pci_de
.port_ops = &artop6260_ops,
};
struct ata_port_info *port_info[2];
- struct ata_port_info *info;
+ struct ata_port_info *info = NULL;
int ports = 2;
if (!printed_version++)
@@ -470,16 +470,20 @@ static int artop_init_one (struct pci_de
pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) | 0x80);
}
+
+ BUG_ON(info == NULL);
+
port_info[0] = port_info[1] = info;
return ata_pci_init_one(pdev, port_info, ports);
}
static const struct pci_device_id artop_pci_tbl[] = {
- { 0x1191, 0x0005, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
- { 0x1191, 0x0006, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
- { 0x1191, 0x0007, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
- { 0x1191, 0x0008, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
- { 0x1191, 0x0009, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
+ { PCI_VDEVICE(ARTOP, 0x0005), 0 },
+ { PCI_VDEVICE(ARTOP, 0x0006), 1 },
+ { PCI_VDEVICE(ARTOP, 0x0007), 1 },
+ { PCI_VDEVICE(ARTOP, 0x0008), 2 },
+ { PCI_VDEVICE(ARTOP, 0x0009), 2 },
+
{ } /* terminate list */
};
@@ -500,7 +504,6 @@ static void __exit artop_exit(void)
pci_unregister_driver(&artop_pci_driver);
}
-
module_init(artop_init);
module_exit(artop_exit);
diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
index 6c2269b..1ce28d2 100644
--- a/drivers/ata/pata_atiixp.c
+++ b/drivers/ata/pata_atiixp.c
@@ -267,12 +267,13 @@ static int atiixp_init_one(struct pci_de
return ata_pci_init_one(dev, port_info, 2);
}
-static struct pci_device_id atiixp[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP200_IDE), },
- { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP300_IDE), },
- { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP400_IDE), },
- { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_IDE), },
- { 0, },
+static const struct pci_device_id atiixp[] = {
+ { PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP200_IDE), },
+ { PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP300_IDE), },
+ { PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP400_IDE), },
+ { PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP600_IDE), },
+
+ { },
};
static struct pci_driver atiixp_pci_driver = {
@@ -293,7 +294,6 @@ static void __exit atiixp_exit(void)
pci_unregister_driver(&atiixp_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for ATI IXP200/300/400");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c
index e92b0ef..b9bbd1d 100644
--- a/drivers/ata/pata_cmd64x.c
+++ b/drivers/ata/pata_cmd64x.c
@@ -468,16 +468,17 @@ #endif
return ata_pci_init_one(pdev, port_info, 2);
}
-static struct pci_device_id cmd64x[] = {
- { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_643, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
- { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_646, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
- { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_648, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
- { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_649, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
- { 0, },
+static const struct pci_device_id cmd64x[] = {
+ { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_643), 0 },
+ { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_646), 1 },
+ { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_648), 4 },
+ { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_649), 5 },
+
+ { },
};
static struct pci_driver cmd64x_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = cmd64x,
.probe = cmd64x_init_one,
.remove = ata_pci_remove_one
@@ -488,13 +489,11 @@ static int __init cmd64x_init(void)
return pci_register_driver(&cmd64x_pci_driver);
}
-
static void __exit cmd64x_exit(void)
{
pci_unregister_driver(&cmd64x_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for CMD64x series PATA controllers");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c
index a6c6ceb..2cd3c0f 100644
--- a/drivers/ata/pata_cs5520.c
+++ b/drivers/ata/pata_cs5520.c
@@ -299,10 +299,11 @@ static void __devexit cs5520_remove_one(
/* For now keep DMA off. We can set it for all but A rev CS5510 once the
core ATA code can handle it */
-static struct pci_device_id pata_cs5520[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5510), },
- { PCI_DEVICE(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5520), },
- { 0, },
+static const struct pci_device_id pata_cs5520[] = {
+ { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), },
+ { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), },
+
+ { },
};
static struct pci_driver cs5520_pci_driver = {
@@ -312,7 +313,6 @@ static struct pci_driver cs5520_pci_driv
.remove = cs5520_remove_one
};
-
static int __init cs5520_init(void)
{
return pci_register_driver(&cs5520_pci_driver);
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
index 7bba4d9..a07cc81 100644
--- a/drivers/ata/pata_cs5530.c
+++ b/drivers/ata/pata_cs5530.c
@@ -353,13 +353,14 @@ fail_put:
return -ENODEV;
}
-static struct pci_device_id cs5530[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), },
- { 0, },
+static const struct pci_device_id cs5530[] = {
+ { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), },
+
+ { },
};
static struct pci_driver cs5530_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = cs5530,
.probe = cs5530_init_one,
.remove = ata_pci_remove_one
@@ -370,13 +371,11 @@ static int __init cs5530_init(void)
return pci_register_driver(&cs5530_pci_driver);
}
-
static void __exit cs5530_exit(void)
{
pci_unregister_driver(&cs5530_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the Cyrix/NS/AMD 5530");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_cs5535.c b/drivers/ata/pata_cs5535.c
index d64fcdc..f8def3f 100644
--- a/drivers/ata/pata_cs5535.c
+++ b/drivers/ata/pata_cs5535.c
@@ -257,9 +257,10 @@ static int cs5535_init_one(struct pci_de
return ata_pci_init_one(dev, ports, 1);
}
-static struct pci_device_id cs5535[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_NS, 0x002D), },
- { 0, },
+static const struct pci_device_id cs5535[] = {
+ { PCI_VDEVICE(NS, 0x002D), },
+
+ { },
};
static struct pci_driver cs5535_pci_driver = {
@@ -274,13 +275,11 @@ static int __init cs5535_init(void)
return pci_register_driver(&cs5535_pci_driver);
}
-
static void __exit cs5535_exit(void)
{
pci_unregister_driver(&cs5535_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox, Jens Altmann, Wolfgan Zuleger, Alexander Kiausch");
MODULE_DESCRIPTION("low-level driver for the NS/AMD 5530");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_cypress.c b/drivers/ata/pata_cypress.c
index dfa5ac5..247b436 100644
--- a/drivers/ata/pata_cypress.c
+++ b/drivers/ata/pata_cypress.c
@@ -184,8 +184,8 @@ static int cy82c693_init_one(struct pci_
};
static struct ata_port_info *port_info[1] = { &info };
- /* Devfn 1 is the ATA primary. The secondary is magic and on devfn2. For the
- moment we don't handle the secondary. FIXME */
+ /* Devfn 1 is the ATA primary. The secondary is magic and on devfn2.
+ For the moment we don't handle the secondary. FIXME */
if (PCI_FUNC(pdev->devfn) != 1)
return -ENODEV;
@@ -193,13 +193,14 @@ static int cy82c693_init_one(struct pci_
return ata_pci_init_one(pdev, port_info, 1);
}
-static struct pci_device_id cy82c693[] = {
- { PCI_VENDOR_ID_CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
- { 0, },
+static const struct pci_device_id cy82c693[] = {
+ { PCI_VDEVICE(CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693), },
+
+ { },
};
static struct pci_driver cy82c693_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = cy82c693,
.probe = cy82c693_init_one,
.remove = ata_pci_remove_one
diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c
index 95cd1ca..ef18c60 100644
--- a/drivers/ata/pata_efar.c
+++ b/drivers/ata/pata_efar.c
@@ -305,7 +305,8 @@ static int efar_init_one (struct pci_dev
}
static const struct pci_device_id efar_pci_tbl[] = {
- { 0x1055, 0x9130, PCI_ANY_ID, PCI_ANY_ID, },
+ { PCI_VDEVICE(EFAR, 0x9130), },
+
{ } /* terminate list */
};
@@ -326,7 +327,6 @@ static void __exit efar_exit(void)
pci_unregister_driver(&efar_pci_driver);
}
-
module_init(efar_init);
module_exit(efar_exit);
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index cf656ec..68a0e57 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -444,13 +444,14 @@ static int hpt36x_init_one(struct pci_de
return ata_pci_init_one(dev, port_info, 2);
}
-static struct pci_device_id hpt36x[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), },
- { 0, },
+static const struct pci_device_id hpt36x[] = {
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
+
+ { },
};
static struct pci_driver hpt36x_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = hpt36x,
.probe = hpt36x_init_one,
.remove = ata_pci_remove_one
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index 10318c0..7350443 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -1219,17 +1219,18 @@ static int hpt37x_init_one(struct pci_de
return ata_pci_init_one(dev, port_info, 2);
}
-static struct pci_device_id hpt37x[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), },
- { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT371), },
- { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372), },
- { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT374), },
- { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302), },
- { 0, },
+static const struct pci_device_id hpt37x[] = {
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT374), },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), },
+
+ { },
};
static struct pci_driver hpt37x_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = hpt37x,
.probe = hpt37x_init_one,
.remove = ata_pci_remove_one
@@ -1240,13 +1241,11 @@ static int __init hpt37x_init(void)
return pci_register_driver(&hpt37x_pci_driver);
}
-
static void __exit hpt37x_exit(void)
{
pci_unregister_driver(&hpt37x_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the Highpoint HPT37x/30x");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index 5c5d4f6..58cfb2b 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -560,16 +560,17 @@ static int hpt3x2n_init_one(struct pci_d
return ata_pci_init_one(dev, port_info, 2);
}
-static struct pci_device_id hpt3x2n[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), },
- { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372), },
- { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302), },
- { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372N), },
- { 0, },
+static const struct pci_device_id hpt3x2n[] = {
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372N), },
+
+ { },
};
static struct pci_driver hpt3x2n_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = hpt3x2n,
.probe = hpt3x2n_init_one,
.remove = ata_pci_remove_one
@@ -580,13 +581,11 @@ static int __init hpt3x2n_init(void)
return pci_register_driver(&hpt3x2n_pci_driver);
}
-
static void __exit hpt3x2n_exit(void)
{
pci_unregister_driver(&hpt3x2n_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the Highpoint HPT3x2n/30x");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
index 1f084ab..3334d72 100644
--- a/drivers/ata/pata_hpt3x3.c
+++ b/drivers/ata/pata_hpt3x3.c
@@ -192,13 +192,14 @@ static int hpt3x3_init_one(struct pci_de
return ata_pci_init_one(dev, port_info, 2);
}
-static struct pci_device_id hpt3x3[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT343), },
- { 0, },
+static const struct pci_device_id hpt3x3[] = {
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT343), },
+
+ { },
};
static struct pci_driver hpt3x3_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = hpt3x3,
.probe = hpt3x3_init_one,
.remove = ata_pci_remove_one
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
index 82a46ff..18ff3e5 100644
--- a/drivers/ata/pata_it821x.c
+++ b/drivers/ata/pata_it821x.c
@@ -808,14 +808,15 @@ static int it821x_init_one(struct pci_de
return ata_pci_init_one(pdev, port_info, 2);
}
-static struct pci_device_id it821x[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8211), },
- { PCI_DEVICE(PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8212), },
- { 0, },
+static const struct pci_device_id it821x[] = {
+ { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), },
+ { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), },
+
+ { },
};
static struct pci_driver it821x_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = it821x,
.probe = it821x_init_one,
.remove = ata_pci_remove_one
@@ -826,13 +827,11 @@ static int __init it821x_init(void)
return pci_register_driver(&it821x_pci_driver);
}
-
static void __exit it821x_exit(void)
{
pci_unregister_driver(&it821x_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the IT8211/IT8212 IDE RAID controller");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
index be3a866..52a2bdf 100644
--- a/drivers/ata/pata_jmicron.c
+++ b/drivers/ata/pata_jmicron.c
@@ -229,11 +229,12 @@ static int jmicron_init_one (struct pci_
}
static const struct pci_device_id jmicron_pci_tbl[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361), 361},
- { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363), 363},
- { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365), 365},
- { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366), 366},
- { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368), 368},
+ { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB361), 361},
+ { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB363), 363},
+ { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB365), 365},
+ { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB366), 366},
+ { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB368), 368},
+
{ } /* terminate list */
};
diff --git a/drivers/ata/pata_mpiix.c b/drivers/ata/pata_mpiix.c
index 3c65393..9dfe3e9 100644
--- a/drivers/ata/pata_mpiix.c
+++ b/drivers/ata/pata_mpiix.c
@@ -274,11 +274,10 @@ static void __devexit mpiix_remove_one(s
dev_set_drvdata(dev, NULL);
}
-
-
static const struct pci_device_id mpiix[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371MX), },
- { 0, },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX), },
+
+ { },
};
static struct pci_driver mpiix_pci_driver = {
@@ -293,13 +292,11 @@ static int __init mpiix_init(void)
return pci_register_driver(&mpiix_pci_driver);
}
-
static void __exit mpiix_exit(void)
{
pci_unregister_driver(&mpiix_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Intel MPIIX");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_netcell.c b/drivers/ata/pata_netcell.c
index 76eb9c9..f5672de 100644
--- a/drivers/ata/pata_netcell.c
+++ b/drivers/ata/pata_netcell.c
@@ -142,7 +142,8 @@ static int netcell_init_one (struct pci_
}
static const struct pci_device_id netcell_pci_tbl[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_NETCELL, PCI_DEVICE_ID_REVOLUTION), },
+ { PCI_VDEVICE(NETCELL, PCI_DEVICE_ID_REVOLUTION), },
+
{ } /* terminate list */
};
diff --git a/drivers/ata/pata_ns87410.c b/drivers/ata/pata_ns87410.c
index 2005a95..2a3dbee 100644
--- a/drivers/ata/pata_ns87410.c
+++ b/drivers/ata/pata_ns87410.c
@@ -200,12 +200,13 @@ static int ns87410_init_one(struct pci_d
}
static const struct pci_device_id ns87410[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87410), },
- { 0, },
+ { PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_87410), },
+
+ { },
};
static struct pci_driver ns87410_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = ns87410,
.probe = ns87410_init_one,
.remove = ata_pci_remove_one
@@ -216,13 +217,11 @@ static int __init ns87410_init(void)
return pci_register_driver(&ns87410_pci_driver);
}
-
static void __exit ns87410_exit(void)
{
pci_unregister_driver(&ns87410_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Nat Semi 87410");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c
index 31a285c..fc947df 100644
--- a/drivers/ata/pata_oldpiix.c
+++ b/drivers/ata/pata_oldpiix.c
@@ -303,7 +303,8 @@ static int oldpiix_init_one (struct pci_
}
static const struct pci_device_id oldpiix_pci_tbl[] = {
- { PCI_DEVICE(0x8086, 0x1230), },
+ { PCI_VDEVICE(INTEL, 0x1230), },
+
{ } /* terminate list */
};
@@ -324,7 +325,6 @@ static void __exit oldpiix_exit(void)
pci_unregister_driver(&oldpiix_pci_driver);
}
-
module_init(oldpiix_init);
module_exit(oldpiix_exit);
diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c
index 57fe21f..a7320ba 100644
--- a/drivers/ata/pata_opti.c
+++ b/drivers/ata/pata_opti.c
@@ -256,13 +256,14 @@ static int opti_init_one(struct pci_dev
}
static const struct pci_device_id opti[] = {
- { PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C621, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
- { PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
- { 0, },
+ { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 },
+ { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 },
+
+ { },
};
static struct pci_driver opti_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = opti,
.probe = opti_init_one,
.remove = ata_pci_remove_one
@@ -273,7 +274,6 @@ static int __init opti_init(void)
return pci_register_driver(&opti_pci_driver);
}
-
static void __exit opti_exit(void)
{
pci_unregister_driver(&opti_pci_driver);
diff --git a/drivers/ata/pata_optidma.c b/drivers/ata/pata_optidma.c
index 7296a20..c6906b4 100644
--- a/drivers/ata/pata_optidma.c
+++ b/drivers/ata/pata_optidma.c
@@ -512,12 +512,13 @@ static int optidma_init_one(struct pci_d
}
static const struct pci_device_id optidma[] = {
- { PCI_DEVICE(0x1045, 0xD568), }, /* Opti 82C700 */
- { 0, },
+ { PCI_VDEVICE(OPTI, 0xD568), }, /* Opti 82C700 */
+
+ { },
};
static struct pci_driver optidma_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = optidma,
.probe = optidma_init_one,
.remove = ata_pci_remove_one
@@ -528,13 +529,11 @@ static int __init optidma_init(void)
return pci_register_driver(&optidma_pci_driver);
}
-
static void __exit optidma_exit(void)
{
pci_unregister_driver(&optidma_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Opti Firestar/Firestar Plus");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_pdc2027x.c b/drivers/ata/pata_pdc2027x.c
index bd4ed67..d894d99 100644
--- a/drivers/ata/pata_pdc2027x.c
+++ b/drivers/ata/pata_pdc2027x.c
@@ -108,13 +108,14 @@ static struct pdc2027x_udma_timing {
};
static const struct pci_device_id pdc2027x_pci_tbl[] = {
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20268, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_100 },
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20269, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20270, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_100 },
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20271, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20275, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20276, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20277, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20268), PDC_UDMA_100 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20269), PDC_UDMA_133 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20270), PDC_UDMA_100 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20271), PDC_UDMA_133 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20275), PDC_UDMA_133 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20276), PDC_UDMA_133 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20277), PDC_UDMA_133 },
+
{ } /* terminate list */
};
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c
index 48f4343..5ba9eb2 100644
--- a/drivers/ata/pata_pdc202xx_old.c
+++ b/drivers/ata/pata_pdc202xx_old.c
@@ -385,17 +385,18 @@ static int pdc_init_one(struct pci_dev *
return ata_pci_init_one(dev, port_info, 2);
}
-static struct pci_device_id pdc[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20246), 0},
- { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20262), 1},
- { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20263), 1},
- { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20265), 2},
- { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20267), 2},
- { 0, },
+static const struct pci_device_id pdc[] = {
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20246), 0 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20262), 1 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20263), 1 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20265), 2 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20267), 2 },
+
+ { },
};
static struct pci_driver pdc_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = pdc,
.probe = pdc_init_one,
.remove = ata_pci_remove_one
@@ -406,13 +407,11 @@ static int __init pdc_init(void)
return pci_register_driver(&pdc_pci_driver);
}
-
static void __exit pdc_exit(void)
{
pci_unregister_driver(&pdc_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Promise 2024x and 20262-20267");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c
index c20bcf4..1af83d7 100644
--- a/drivers/ata/pata_radisys.c
+++ b/drivers/ata/pata_radisys.c
@@ -300,7 +300,8 @@ static int radisys_init_one (struct pci_
}
static const struct pci_device_id radisys_pci_tbl[] = {
- { 0x1331, 0x8201, PCI_ANY_ID, PCI_ANY_ID, },
+ { PCI_VDEVICE(RADISYS, 0x8201), },
+
{ } /* terminate list */
};
@@ -321,7 +322,6 @@ static void __exit radisys_exit(void)
pci_unregister_driver(&radisys_pci_driver);
}
-
module_init(radisys_init);
module_exit(radisys_exit);
diff --git a/drivers/ata/pata_rz1000.c b/drivers/ata/pata_rz1000.c
index eccc6fd..4533b63 100644
--- a/drivers/ata/pata_rz1000.c
+++ b/drivers/ata/pata_rz1000.c
@@ -170,20 +170,20 @@ fail:
return -ENODEV;
}
-static struct pci_device_id pata_rz1000[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_PCTECH, PCI_DEVICE_ID_PCTECH_RZ1000), },
- { PCI_DEVICE(PCI_VENDOR_ID_PCTECH, PCI_DEVICE_ID_PCTECH_RZ1001), },
- { 0, },
+static const struct pci_device_id pata_rz1000[] = {
+ { PCI_VDEVICE(PCTECH, PCI_DEVICE_ID_PCTECH_RZ1000), },
+ { PCI_VDEVICE(PCTECH, PCI_DEVICE_ID_PCTECH_RZ1001), },
+
+ { },
};
static struct pci_driver rz1000_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = pata_rz1000,
.probe = rz1000_init_one,
.remove = ata_pci_remove_one
};
-
static int __init rz1000_init(void)
{
return pci_register_driver(&rz1000_pci_driver);
diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c
index 107e6cd..067d9d2 100644
--- a/drivers/ata/pata_sc1200.c
+++ b/drivers/ata/pata_sc1200.c
@@ -253,13 +253,14 @@ static int sc1200_init_one(struct pci_de
return ata_pci_init_one(dev, port_info, 1);
}
-static struct pci_device_id sc1200[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SCx200_IDE), },
- { 0, },
+static const struct pci_device_id sc1200[] = {
+ { PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_SCx200_IDE), },
+
+ { },
};
static struct pci_driver sc1200_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = sc1200,
.probe = sc1200_init_one,
.remove = ata_pci_remove_one
@@ -270,13 +271,11 @@ static int __init sc1200_init(void)
return pci_register_driver(&sc1200_pci_driver);
}
-
static void __exit sc1200_exit(void)
{
pci_unregister_driver(&sc1200_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox, Mark Lord");
MODULE_DESCRIPTION("low-level driver for the NS/AMD SC1200");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c
index a5c8d7e..5bbf76e 100644
--- a/drivers/ata/pata_serverworks.c
+++ b/drivers/ata/pata_serverworks.c
@@ -553,13 +553,14 @@ static int serverworks_init_one(struct p
return ata_pci_init_one(pdev, port_info, ports);
}
-static struct pci_device_id serverworks[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0},
- { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 2},
- { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2},
- { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 2},
- { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 2},
- { 0, },
+static const struct pci_device_id serverworks[] = {
+ { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0},
+ { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 2},
+ { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2},
+ { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 2},
+ { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 2},
+
+ { },
};
static struct pci_driver serverworks_pci_driver = {
@@ -574,13 +575,11 @@ static int __init serverworks_init(void)
return pci_register_driver(&serverworks_pci_driver);
}
-
static void __exit serverworks_exit(void)
{
pci_unregister_driver(&serverworks_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Serverworks OSB4/CSB5/CSB6");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index c8b2e26..4a2b72b 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -348,12 +348,13 @@ static int sil680_init_one(struct pci_de
}
static const struct pci_device_id sil680[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_SII_680), },
- { 0, },
+ { PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_680), },
+
+ { },
};
static struct pci_driver sil680_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = sil680,
.probe = sil680_init_one,
.remove = ata_pci_remove_one
@@ -364,13 +365,11 @@ static int __init sil680_init(void)
return pci_register_driver(&sil680_pci_driver);
}
-
static void __exit sil680_exit(void)
{
pci_unregister_driver(&sil680_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for SI680 PATA");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index 17791e2..b9ffafb 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -988,8 +988,9 @@ static int sis_init_one (struct pci_dev
}
static const struct pci_device_id sis_pci_tbl[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_SI, 0x5513), }, /* SiS 5513 */
- { PCI_DEVICE(PCI_VENDOR_ID_SI, 0x5518), }, /* SiS 5518 */
+ { PCI_VDEVICE(SI, 0x5513), }, /* SiS 5513 */
+ { PCI_VDEVICE(SI, 0x5518), }, /* SiS 5518 */
+
{ }
};
@@ -1010,7 +1011,6 @@ static void __exit sis_exit(void)
pci_unregister_driver(&sis_pci_driver);
}
-
module_init(sis_init);
module_exit(sis_exit);
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index 5b762ac..08a6dc8 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -351,9 +351,10 @@ static int sl82c105_init_one(struct pci_
return ata_pci_init_one(dev, port_info, 1); /* For now */
}
-static struct pci_device_id sl82c105[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_WINBOND, PCI_DEVICE_ID_WINBOND_82C105), },
- { 0, },
+static const struct pci_device_id sl82c105[] = {
+ { PCI_VDEVICE(WINBOND, PCI_DEVICE_ID_WINBOND_82C105), },
+
+ { },
};
static struct pci_driver sl82c105_pci_driver = {
@@ -368,13 +369,11 @@ static int __init sl82c105_init(void)
return pci_register_driver(&sl82c105_pci_driver);
}
-
static void __exit sl82c105_exit(void)
{
pci_unregister_driver(&sl82c105_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Sl82c105");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_triflex.c b/drivers/ata/pata_triflex.c
index a954ed9..9640f80 100644
--- a/drivers/ata/pata_triflex.c
+++ b/drivers/ata/pata_triflex.c
@@ -248,13 +248,13 @@ static int triflex_init_one(struct pci_d
}
static const struct pci_device_id triflex[] = {
- { PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_COMPAQ_TRIFLEX_IDE,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { 0, },
+ { PCI_VDEVICE(COMPAQ, PCI_DEVICE_ID_COMPAQ_TRIFLEX_IDE), },
+
+ { },
};
static struct pci_driver triflex_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = triflex,
.probe = triflex_init_one,
.remove = ata_pci_remove_one
@@ -265,13 +265,11 @@ static int __init triflex_init(void)
return pci_register_driver(&triflex_pci_driver);
}
-
static void __exit triflex_exit(void)
{
pci_unregister_driver(&triflex_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Compaq Triflex");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 7b5dd23..1e7be9e 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -529,15 +529,16 @@ static int via_init_one(struct pci_dev *
}
static const struct pci_device_id via[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576_1), },
- { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1), },
- { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_6410), },
- { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_SATA_EIDE), },
- { 0, },
+ { PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_82C576_1), },
+ { PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_82C586_1), },
+ { PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_6410), },
+ { PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_SATA_EIDE), },
+
+ { },
};
static struct pci_driver via_pci_driver = {
- .name = DRV_NAME,
+ .name = DRV_NAME,
.id_table = via,
.probe = via_init_one,
.remove = ata_pci_remove_one
@@ -548,13 +549,11 @@ static int __init via_init(void)
return pci_register_driver(&via_pci_driver);
}
-
static void __exit via_exit(void)
{
pci_unregister_driver(&via_pci_driver);
}
-
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for VIA PATA");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/pdc_adma.c b/drivers/ata/pdc_adma.c
index 0e23ecb..81f3d21 100644
--- a/drivers/ata/pdc_adma.c
+++ b/drivers/ata/pdc_adma.c
@@ -192,8 +192,7 @@ static struct ata_port_info adma_port_in
};
static const struct pci_device_id adma_ata_pci_tbl[] = {
- { PCI_VENDOR_ID_PDC, 0x1841, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_1841_idx },
+ { PCI_VDEVICE(PDC, 0x1841), board_1841_idx },
{ } /* terminate list */
};
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index c01496d..e6aa1a8 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -533,19 +533,20 @@ static const struct ata_port_info mv_por
};
static const struct pci_device_id mv_pci_tbl[] = {
- {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5040), 0, 0, chip_504x},
- {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5041), 0, 0, chip_504x},
- {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5080), 0, 0, chip_5080},
- {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5081), 0, 0, chip_508x},
-
- {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6040), 0, 0, chip_604x},
- {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6041), 0, 0, chip_604x},
- {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6042), 0, 0, chip_6042},
- {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6080), 0, 0, chip_608x},
- {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6081), 0, 0, chip_608x},
-
- {PCI_DEVICE(PCI_VENDOR_ID_ADAPTEC2, 0x0241), 0, 0, chip_604x},
- {} /* terminate list */
+ { PCI_VDEVICE(MARVELL, 0x5040), chip_504x },
+ { PCI_VDEVICE(MARVELL, 0x5041), chip_504x },
+ { PCI_VDEVICE(MARVELL, 0x5080), chip_5080 },
+ { PCI_VDEVICE(MARVELL, 0x5081), chip_508x },
+
+ { PCI_VDEVICE(MARVELL, 0x6040), chip_604x },
+ { PCI_VDEVICE(MARVELL, 0x6041), chip_604x },
+ { PCI_VDEVICE(MARVELL, 0x6042), chip_6042 },
+ { PCI_VDEVICE(MARVELL, 0x6080), chip_608x },
+ { PCI_VDEVICE(MARVELL, 0x6081), chip_608x },
+
+ { PCI_VDEVICE(ADAPTEC2, 0x0241), chip_604x },
+
+ { } /* terminate list */
};
static struct pci_driver mv_pci_driver = {
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 8cd730f..d09d20a 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -106,45 +106,32 @@ enum nv_host_type
};
static const struct pci_device_id nv_pci_tbl[] = {
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_SATA,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, NFORCE2 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, NFORCE3 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA2,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, NFORCE3 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_SATA,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, CK804 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_SATA2,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, CK804 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_SATA,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, CK804 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_SATA2,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, CK804 },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA2,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA2,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC },
- { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA3,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC },
- { PCI_VENDOR_ID_NVIDIA, 0x045c, PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC },
- { PCI_VENDOR_ID_NVIDIA, 0x045d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC },
- { PCI_VENDOR_ID_NVIDIA, 0x045e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC },
- { PCI_VENDOR_ID_NVIDIA, 0x045f, PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_SATA), NFORCE2 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA), NFORCE3 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA2), NFORCE3 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_SATA), CK804 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_SATA2), CK804 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_SATA), CK804 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_SATA2), CK804 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA), GENERIC },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2), GENERIC },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA), GENERIC },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA2), GENERIC },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA), GENERIC },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA2), GENERIC },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA3), GENERIC },
+ { PCI_VDEVICE(NVIDIA, 0x045c), GENERIC },
+ { PCI_VDEVICE(NVIDIA, 0x045d), GENERIC },
+ { PCI_VDEVICE(NVIDIA, 0x045e), GENERIC },
+ { PCI_VDEVICE(NVIDIA, 0x045f), GENERIC },
{ PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID,
PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_STORAGE_IDE<<8, 0xffff00, GENERIC },
{ PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID,
PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_STORAGE_RAID<<8, 0xffff00, GENERIC },
- { 0, } /* terminate list */
+
+ { } /* terminate list */
};
static struct pci_driver nv_pci_driver = {
diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c
index d627812..15c9437 100644
--- a/drivers/ata/sata_promise.c
+++ b/drivers/ata/sata_promise.c
@@ -234,48 +234,31 @@ static const struct ata_port_info pdc_po
};
static const struct pci_device_id pdc_ata_pci_tbl[] = {
- { PCI_VENDOR_ID_PROMISE, 0x3371, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_2037x },
- { PCI_VENDOR_ID_PROMISE, 0x3570, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_2037x },
- { PCI_VENDOR_ID_PROMISE, 0x3571, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_2037x },
- { PCI_VENDOR_ID_PROMISE, 0x3373, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_2037x },
- { PCI_VENDOR_ID_PROMISE, 0x3375, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_2037x },
- { PCI_VENDOR_ID_PROMISE, 0x3376, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_2037x },
- { PCI_VENDOR_ID_PROMISE, 0x3574, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_2057x },
- { PCI_VENDOR_ID_PROMISE, 0x3d75, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_2057x },
- { PCI_VENDOR_ID_PROMISE, 0x3d73, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_2037x },
-
- { PCI_VENDOR_ID_PROMISE, 0x3318, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_20319 },
- { PCI_VENDOR_ID_PROMISE, 0x3319, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_20319 },
- { PCI_VENDOR_ID_PROMISE, 0x3515, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_20319 },
- { PCI_VENDOR_ID_PROMISE, 0x3519, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_20319 },
- { PCI_VENDOR_ID_PROMISE, 0x3d17, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_20319 },
- { PCI_VENDOR_ID_PROMISE, 0x3d18, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_40518 },
-
- { PCI_VENDOR_ID_PROMISE, 0x6629, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_20619 },
+ { PCI_VDEVICE(PROMISE, 0x3371), board_2037x },
+ { PCI_VDEVICE(PROMISE, 0x3570), board_2037x },
+ { PCI_VDEVICE(PROMISE, 0x3571), board_2037x },
+ { PCI_VDEVICE(PROMISE, 0x3373), board_2037x },
+ { PCI_VDEVICE(PROMISE, 0x3375), board_2037x },
+ { PCI_VDEVICE(PROMISE, 0x3376), board_2037x },
+ { PCI_VDEVICE(PROMISE, 0x3574), board_2057x },
+ { PCI_VDEVICE(PROMISE, 0x3d75), board_2057x },
+ { PCI_VDEVICE(PROMISE, 0x3d73), board_2037x },
+
+ { PCI_VDEVICE(PROMISE, 0x3318), board_20319 },
+ { PCI_VDEVICE(PROMISE, 0x3319), board_20319 },
+ { PCI_VDEVICE(PROMISE, 0x3515), board_20319 },
+ { PCI_VDEVICE(PROMISE, 0x3519), board_20319 },
+ { PCI_VDEVICE(PROMISE, 0x3d17), board_20319 },
+ { PCI_VDEVICE(PROMISE, 0x3d18), board_40518 },
+
+ { PCI_VDEVICE(PROMISE, 0x6629), board_20619 },
/* TODO: remove all associated board_20771 code, as it completely
* duplicates board_2037x code, unless reason for separation can be
* divined.
*/
#if 0
- { PCI_VENDOR_ID_PROMISE, 0x3570, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_20771 },
+ { PCI_VDEVICE(PROMISE, 0x3570), board_20771 },
#endif
{ } /* terminate list */
diff --git a/drivers/ata/sata_qstor.c b/drivers/ata/sata_qstor.c
index fa29dfe..7f6cc3c 100644
--- a/drivers/ata/sata_qstor.c
+++ b/drivers/ata/sata_qstor.c
@@ -185,8 +185,7 @@ static const struct ata_port_info qs_por
};
static const struct pci_device_id qs_ata_pci_tbl[] = {
- { PCI_VENDOR_ID_PDC, 0x2068, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_2068_idx },
+ { PCI_VDEVICE(PDC, 0x2068), board_2068_idx },
{ } /* terminate list */
};
diff --git a/drivers/ata/sata_sil.c b/drivers/ata/sata_sil.c
index c63dbab..3d9fa1c 100644
--- a/drivers/ata/sata_sil.c
+++ b/drivers/ata/sata_sil.c
@@ -123,13 +123,14 @@ static void sil_thaw(struct ata_port *ap
static const struct pci_device_id sil_pci_tbl[] = {
- { 0x1095, 0x3112, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
- { 0x1095, 0x0240, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
- { 0x1095, 0x3512, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3512 },
- { 0x1095, 0x3114, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3114 },
- { 0x1002, 0x436e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
- { 0x1002, 0x4379, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_no_sata_irq },
- { 0x1002, 0x437a, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_no_sata_irq },
+ { PCI_VDEVICE(CMD, 0x3112), sil_3112 },
+ { PCI_VDEVICE(CMD, 0x0240), sil_3112 },
+ { PCI_VDEVICE(CMD, 0x3512), sil_3512 },
+ { PCI_VDEVICE(CMD, 0x3114), sil_3114 },
+ { PCI_VDEVICE(ATI, 0x436e), sil_3112 },
+ { PCI_VDEVICE(ATI, 0x4379), sil_3112_no_sata_irq },
+ { PCI_VDEVICE(ATI, 0x437a), sil_3112_no_sata_irq },
+
{ } /* terminate list */
};
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index 39cb07b..a951f40 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -344,11 +344,12 @@ static int sil24_pci_device_resume(struc
#endif
static const struct pci_device_id sil24_pci_tbl[] = {
- { 0x1095, 0x3124, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3124 },
- { 0x8086, 0x3124, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3124 },
- { 0x1095, 0x3132, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3132 },
- { 0x1095, 0x3131, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3131 },
- { 0x1095, 0x3531, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3131 },
+ { PCI_VDEVICE(CMD, 0x3124), BID_SIL3124 },
+ { PCI_VDEVICE(INTEL, 0x3124), BID_SIL3124 },
+ { PCI_VDEVICE(CMD, 0x3132), BID_SIL3132 },
+ { PCI_VDEVICE(CMD, 0x3131), BID_SIL3131 },
+ { PCI_VDEVICE(CMD, 0x3531), BID_SIL3131 },
+
{ } /* terminate list */
};
diff --git a/drivers/ata/sata_sis.c b/drivers/ata/sata_sis.c
index 18d49ff..0738f52 100644
--- a/drivers/ata/sata_sis.c
+++ b/drivers/ata/sata_sis.c
@@ -67,13 +67,13 @@ static u32 sis_scr_read (struct ata_port
static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static const struct pci_device_id sis_pci_tbl[] = {
- { PCI_VENDOR_ID_SI, 0x180, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sis_180 },
- { PCI_VENDOR_ID_SI, 0x181, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sis_180 },
- { PCI_VENDOR_ID_SI, 0x182, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sis_180 },
+ { PCI_VDEVICE(SI, 0x180), sis_180 },
+ { PCI_VDEVICE(SI, 0x181), sis_180 },
+ { PCI_VDEVICE(SI, 0x182), sis_180 },
+
{ } /* terminate list */
};
-
static struct pci_driver sis_pci_driver = {
.name = DRV_NAME,
.id_table = sis_pci_tbl,
diff --git a/drivers/ata/sata_svw.c b/drivers/ata/sata_svw.c
index d6d6658..84025a2 100644
--- a/drivers/ata/sata_svw.c
+++ b/drivers/ata/sata_svw.c
@@ -469,15 +469,15 @@ err_out:
* controller
* */
static const struct pci_device_id k2_sata_pci_tbl[] = {
- { 0x1166, 0x0240, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
- { 0x1166, 0x0241, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
- { 0x1166, 0x0242, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
- { 0x1166, 0x024a, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
- { 0x1166, 0x024b, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0240), 4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0241), 4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0242), 8 },
+ { PCI_VDEVICE(SERVERWORKS, 0x024a), 4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x024b), 4 },
+
{ }
};
-
static struct pci_driver k2_sata_pci_driver = {
.name = DRV_NAME,
.id_table = k2_sata_pci_tbl,
@@ -485,19 +485,16 @@ static struct pci_driver k2_sata_pci_dri
.remove = ata_pci_remove_one,
};
-
static int __init k2_sata_init(void)
{
return pci_register_driver(&k2_sata_pci_driver);
}
-
static void __exit k2_sata_exit(void)
{
pci_unregister_driver(&k2_sata_pci_driver);
}
-
MODULE_AUTHOR("Benjamin Herrenschmidt");
MODULE_DESCRIPTION("low-level driver for K2 SATA controller");
MODULE_LICENSE("GPL");
diff --git a/drivers/ata/sata_sx4.c b/drivers/ata/sata_sx4.c
index 091867e..8c74f2f 100644
--- a/drivers/ata/sata_sx4.c
+++ b/drivers/ata/sata_sx4.c
@@ -230,12 +230,11 @@ static const struct ata_port_info pdc_po
};
static const struct pci_device_id pdc_sata_pci_tbl[] = {
- { PCI_VENDOR_ID_PROMISE, 0x6622, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- board_20621 },
+ { PCI_VDEVICE(PROMISE, 0x6622), board_20621 },
+
{ } /* terminate list */
};
-
static struct pci_driver pdc_sata_pci_driver = {
.name = DRV_NAME,
.id_table = pdc_sata_pci_tbl,
diff --git a/drivers/ata/sata_uli.c b/drivers/ata/sata_uli.c
index dd76f37..5c603ca 100644
--- a/drivers/ata/sata_uli.c
+++ b/drivers/ata/sata_uli.c
@@ -61,13 +61,13 @@ static u32 uli_scr_read (struct ata_port
static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static const struct pci_device_id uli_pci_tbl[] = {
- { PCI_VENDOR_ID_AL, 0x5289, PCI_ANY_ID, PCI_ANY_ID, 0, 0, uli_5289 },
- { PCI_VENDOR_ID_AL, 0x5287, PCI_ANY_ID, PCI_ANY_ID, 0, 0, uli_5287 },
- { PCI_VENDOR_ID_AL, 0x5281, PCI_ANY_ID, PCI_ANY_ID, 0, 0, uli_5281 },
+ { PCI_VDEVICE(AL, 0x5289), uli_5289 },
+ { PCI_VDEVICE(AL, 0x5287), uli_5287 },
+ { PCI_VDEVICE(AL, 0x5281), uli_5281 },
+
{ } /* terminate list */
};
-
static struct pci_driver uli_pci_driver = {
.name = DRV_NAME,
.id_table = uli_pci_tbl,
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index a72a238..f4455a1 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -77,9 +77,9 @@ static void svia_scr_write (struct ata_p
static void vt6420_error_handler(struct ata_port *ap);
static const struct pci_device_id svia_pci_tbl[] = {
- { 0x1106, 0x0591, PCI_ANY_ID, PCI_ANY_ID, 0, 0, vt6420 },
- { 0x1106, 0x3149, PCI_ANY_ID, PCI_ANY_ID, 0, 0, vt6420 },
- { 0x1106, 0x3249, PCI_ANY_ID, PCI_ANY_ID, 0, 0, vt6421 },
+ { PCI_VDEVICE(VIA, 0x0591), vt6420 },
+ { PCI_VDEVICE(VIA, 0x3149), vt6420 },
+ { PCI_VDEVICE(VIA, 0x3249), vt6421 },
{ } /* terminate list */
};
diff --git a/drivers/ata/sata_vsc.c b/drivers/ata/sata_vsc.c
index d0d92f3..273d88f 100644
--- a/drivers/ata/sata_vsc.c
+++ b/drivers/ata/sata_vsc.c
@@ -442,16 +442,15 @@ err_out:
return rc;
}
-
static const struct pci_device_id vsc_sata_pci_tbl[] = {
{ PCI_VENDOR_ID_VITESSE, 0x7174,
PCI_ANY_ID, PCI_ANY_ID, 0x10600, 0xFFFFFF, 0 },
{ PCI_VENDOR_ID_INTEL, 0x3200,
PCI_ANY_ID, PCI_ANY_ID, 0x10600, 0xFFFFFF, 0 },
+
{ } /* terminate list */
};
-
static struct pci_driver vsc_sata_pci_driver = {
.name = DRV_NAME,
.id_table = vsc_sata_pci_tbl,
@@ -459,19 +458,16 @@ static struct pci_driver vsc_sata_pci_dr
.remove = ata_pci_remove_one,
};
-
static int __init vsc_sata_init(void)
{
return pci_register_driver(&vsc_sata_pci_driver);
}
-
static void __exit vsc_sata_exit(void)
{
pci_unregister_driver(&vsc_sata_pci_driver);
}
-
MODULE_AUTHOR("Jeremy Higdon");
MODULE_DESCRIPTION("low-level driver for Vitesse VSC7174 SATA controller");
MODULE_LICENSE("GPL");
diff --git a/include/linux/libata.h b/include/linux/libata.h
index d6a3d4b..d1af1db 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -109,6 +109,10 @@ static inline u32 ata_msg_init(int dval,
#define ATA_TAG_POISON 0xfafbfcfdU
/* move to PCI layer? */
+#define PCI_VDEVICE(vendor, device) \
+ PCI_VENDOR_ID_##vendor, (device), \
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0
+
static inline struct device *pci_dev_to_dev(struct pci_dev *pdev)
{
return &pdev->dev;
@@ -138,8 +142,9 @@ enum {
ATA_DFLAG_NCQ = (1 << 3), /* device supports NCQ */
ATA_DFLAG_CFG_MASK = (1 << 8) - 1,
- ATA_DFLAG_PIO = (1 << 8), /* device currently in PIO mode */
- ATA_DFLAG_SUSPENDED = (1 << 9), /* device suspended */
+ ATA_DFLAG_PIO = (1 << 8), /* device limited to PIO mode */
+ ATA_DFLAG_NCQ_OFF = (1 << 9), /* devied limited to non-NCQ mode */
+ ATA_DFLAG_SUSPENDED = (1 << 10), /* device suspended */
ATA_DFLAG_INIT_MASK = (1 << 16) - 1,
ATA_DFLAG_DETACH = (1 << 16),
^ permalink raw reply related [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
[not found] <20060924162850.GA14323@havoc.gtf.org>
@ 2006-09-24 16:33 ` Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2006-09-24 16:33 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, LKML
On Sun, Sep 24, 2006 at 12:28:50PM -0400, Jeff Garzik wrote:
>
> Notable changes:
> * move to drivers/ata
> * add Alan's PATA drivers; drivers/ide still primary PATA for some time
> * AHCI suspend/resume
Notable notes I should have included:
* These changes have been in -mm for a while; the PATA drivers have been
in -mm for quite a while
* There were no objections when the PATA merge plan was posted:
http://lkml.org/lkml/2006/8/9/285
> Please pull from 'upstream-linus' branch of
> master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
As an aside, Tejun Heo has an iomap patch that kills the much-hated
libata build warnings, and I have some related work as well. Hopefully
the warnings should go away in 2.6.20.
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2006-03-30 22:01 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2006-03-30 22:01 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, linux-kernel
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git
to receive the following updates:
Documentation/DocBook/libata.tmpl | 47 +++++++++-
drivers/scsi/libata-bmdma.c | 26 ++++-
drivers/scsi/libata-core.c | 168 ++++++++++++++------------------------
drivers/scsi/sata_mv.c | 42 +++++----
include/linux/libata.h | 10 ++
5 files changed, 164 insertions(+), 129 deletions(-)
Alan Cox:
libata: BMDMA handling updates
libata: Add ->set_mode hook for odd drivers
libata - ATA is both ATA and CFA
libata: Simplex and other mode filtering logic
libata: Fix interesting use of "extern" and also some bracketing
Albert Lee:
libata: ata_dev_init_params() fixes
Mark Lord:
sata_mv: three bug fixes
Tejun Heo:
libata: kill E.D.D.
libata: cosmetic changes in ata_bus_softreset()
libata: add FIXME above ata_dev_xfermask()
libata: kill trailing whitespace
diff --git a/Documentation/DocBook/libata.tmpl b/Documentation/DocBook/libata.tmpl
index d260d92..5bcbb6e 100644
--- a/Documentation/DocBook/libata.tmpl
+++ b/Documentation/DocBook/libata.tmpl
@@ -120,14 +120,27 @@ void (*dev_config) (struct ata_port *, s
<programlisting>
void (*set_piomode) (struct ata_port *, struct ata_device *);
void (*set_dmamode) (struct ata_port *, struct ata_device *);
-void (*post_set_mode) (struct ata_port *ap);
+void (*post_set_mode) (struct ata_port *);
+unsigned int (*mode_filter) (struct ata_port *, struct ata_device *, unsigned int);
</programlisting>
<para>
Hooks called prior to the issue of SET FEATURES - XFER MODE
- command. dev->pio_mode is guaranteed to be valid when
- ->set_piomode() is called, and dev->dma_mode is guaranteed to be
- valid when ->set_dmamode() is called. ->post_set_mode() is
+ command. The optional ->mode_filter() hook is called when libata
+ has built a mask of the possible modes. This is passed to the
+ ->mode_filter() function which should return a mask of valid modes
+ after filtering those unsuitable due to hardware limits. It is not
+ valid to use this interface to add modes.
+ </para>
+ <para>
+ dev->pio_mode and dev->dma_mode are guaranteed to be valid when
+ ->set_piomode() and when ->set_dmamode() is called. The timings for
+ any other drive sharing the cable will also be valid at this point.
+ That is the library records the decisions for the modes of each
+ drive on a channel before it attempts to set any of them.
+ </para>
+ <para>
+ ->post_set_mode() is
called unconditionally, after the SET FEATURES - XFER MODE
command completes successfully.
</para>
@@ -230,6 +243,32 @@ void (*dev_select)(struct ata_port *ap,
</sect2>
+ <sect2><title>Private tuning method</title>
+ <programlisting>
+void (*set_mode) (struct ata_port *ap);
+ </programlisting>
+
+ <para>
+ By default libata performs drive and controller tuning in
+ accordance with the ATA timing rules and also applies blacklists
+ and cable limits. Some controllers need special handling and have
+ custom tuning rules, typically raid controllers that use ATA
+ commands but do not actually do drive timing.
+ </para>
+
+ <warning>
+ <para>
+ This hook should not be used to replace the standard controller
+ tuning logic when a controller has quirks. Replacing the default
+ tuning logic in that case would bypass handling for drive and
+ bridge quirks that may be important to data reliability. If a
+ controller needs to filter the mode selection it should use the
+ mode_filter hook instead.
+ </para>
+ </warning>
+
+ </sect2>
+
<sect2><title>Reset ATA bus</title>
<programlisting>
void (*phy_reset) (struct ata_port *ap);
diff --git a/drivers/scsi/libata-bmdma.c b/drivers/scsi/libata-bmdma.c
index 95d81d8..835dff0 100644
--- a/drivers/scsi/libata-bmdma.c
+++ b/drivers/scsi/libata-bmdma.c
@@ -703,6 +703,7 @@ ata_pci_init_native_mode(struct pci_dev
struct ata_probe_ent *probe_ent =
ata_probe_ent_alloc(pci_dev_to_dev(pdev), port[0]);
int p = 0;
+ unsigned long bmdma;
if (!probe_ent)
return NULL;
@@ -716,7 +717,12 @@ ata_pci_init_native_mode(struct pci_dev
probe_ent->port[p].altstatus_addr =
probe_ent->port[p].ctl_addr =
pci_resource_start(pdev, 1) | ATA_PCI_CTL_OFS;
- probe_ent->port[p].bmdma_addr = pci_resource_start(pdev, 4);
+ bmdma = pci_resource_start(pdev, 4);
+ if (bmdma) {
+ if (inb(bmdma + 2) & 0x80)
+ probe_ent->host_set_flags |= ATA_HOST_SIMPLEX;
+ probe_ent->port[p].bmdma_addr = bmdma;
+ }
ata_std_ports(&probe_ent->port[p]);
p++;
}
@@ -726,7 +732,13 @@ ata_pci_init_native_mode(struct pci_dev
probe_ent->port[p].altstatus_addr =
probe_ent->port[p].ctl_addr =
pci_resource_start(pdev, 3) | ATA_PCI_CTL_OFS;
- probe_ent->port[p].bmdma_addr = pci_resource_start(pdev, 4) + 8;
+ bmdma = pci_resource_start(pdev, 4);
+ if (bmdma) {
+ bmdma += 8;
+ if(inb(bmdma + 2) & 0x80)
+ probe_ent->host_set_flags |= ATA_HOST_SIMPLEX;
+ probe_ent->port[p].bmdma_addr = bmdma;
+ }
ata_std_ports(&probe_ent->port[p]);
p++;
}
@@ -740,6 +752,7 @@ static struct ata_probe_ent *ata_pci_ini
struct ata_port_info *port, int port_num)
{
struct ata_probe_ent *probe_ent;
+ unsigned long bmdma;
probe_ent = ata_probe_ent_alloc(pci_dev_to_dev(pdev), port);
if (!probe_ent)
@@ -766,8 +779,13 @@ static struct ata_probe_ent *ata_pci_ini
break;
}
- probe_ent->port[0].bmdma_addr =
- pci_resource_start(pdev, 4) + 8 * port_num;
+ bmdma = pci_resource_start(pdev, 4);
+ if (bmdma != 0) {
+ bmdma += 8 * port_num;
+ probe_ent->port[0].bmdma_addr = bmdma;
+ if (inb(bmdma + 2) & 0x80)
+ probe_ent->host_set_flags |= ATA_HOST_SIMPLEX;
+ }
ata_std_ports(&probe_ent->port[0]);
return probe_ent;
diff --git a/drivers/scsi/libata-core.c b/drivers/scsi/libata-core.c
index d279666..21b0ed5 100644
--- a/drivers/scsi/libata-core.c
+++ b/drivers/scsi/libata-core.c
@@ -62,7 +62,9 @@
#include "libata.h"
static unsigned int ata_dev_init_params(struct ata_port *ap,
- struct ata_device *dev);
+ struct ata_device *dev,
+ u16 heads,
+ u16 sectors);
static void ata_set_mode(struct ata_port *ap);
static unsigned int ata_dev_set_xfermode(struct ata_port *ap,
struct ata_device *dev);
@@ -1081,9 +1083,8 @@ unsigned int ata_pio_need_iordy(const st
*
* Read ID data from the specified device. ATA_CMD_ID_ATA is
* performed on ATA devices and ATA_CMD_ID_ATAPI on ATAPI
- * devices. This function also takes care of EDD signature
- * misreporting (to be removed once EDD support is gone) and
- * issues ATA_CMD_INIT_DEV_PARAMS for pre-ATA4 drives.
+ * devices. This function also issues ATA_CMD_INIT_DEV_PARAMS
+ * for pre-ATA4 drives.
*
* LOCKING:
* Kernel thread context (may sleep)
@@ -1095,7 +1096,6 @@ static int ata_dev_read_id(struct ata_po
unsigned int *p_class, int post_reset, u16 **p_id)
{
unsigned int class = *p_class;
- unsigned int using_edd;
struct ata_taskfile tf;
unsigned int err_mask = 0;
u16 *id;
@@ -1104,12 +1104,6 @@ static int ata_dev_read_id(struct ata_po
DPRINTK("ENTER, host %u, dev %u\n", ap->id, dev->devno);
- if (ap->ops->probe_reset ||
- ap->flags & (ATA_FLAG_SRST | ATA_FLAG_SATA_RESET))
- using_edd = 0;
- else
- using_edd = 1;
-
ata_dev_select(ap, dev->devno, 1, 1); /* select device 0/1 */
id = kmalloc(sizeof(id[0]) * ATA_ID_WORDS, GFP_KERNEL);
@@ -1139,39 +1133,16 @@ static int ata_dev_read_id(struct ata_po
err_mask = ata_exec_internal(ap, dev, &tf, DMA_FROM_DEVICE,
id, sizeof(id[0]) * ATA_ID_WORDS);
-
if (err_mask) {
rc = -EIO;
reason = "I/O error";
-
- if (err_mask & ~AC_ERR_DEV)
- goto err_out;
-
- /*
- * arg! EDD works for all test cases, but seems to return
- * the ATA signature for some ATAPI devices. Until the
- * reason for this is found and fixed, we fix up the mess
- * here. If IDENTIFY DEVICE returns command aborted
- * (as ATAPI devices do), then we issue an
- * IDENTIFY PACKET DEVICE.
- *
- * ATA software reset (SRST, the default) does not appear
- * to have this problem.
- */
- if ((using_edd) && (class == ATA_DEV_ATA)) {
- u8 err = tf.feature;
- if (err & ATA_ABORTED) {
- class = ATA_DEV_ATAPI;
- goto retry;
- }
- }
goto err_out;
}
swap_buf_le16(id, ATA_ID_WORDS);
/* sanity check */
- if ((class == ATA_DEV_ATA) != ata_id_is_ata(id)) {
+ if ((class == ATA_DEV_ATA) != (ata_id_is_ata(id) | ata_id_is_cfa(id))) {
rc = -EINVAL;
reason = "device reports illegal type";
goto err_out;
@@ -1187,7 +1158,7 @@ static int ata_dev_read_id(struct ata_po
* Some drives were very specific about that exact sequence.
*/
if (ata_id_major_version(id) < 4 || !ata_id_has_lba(id)) {
- err_mask = ata_dev_init_params(ap, dev);
+ err_mask = ata_dev_init_params(ap, dev, id[3], id[6]);
if (err_mask) {
rc = -EIO;
reason = "INIT_DEV_PARAMS failed";
@@ -1440,7 +1411,11 @@ static int ata_bus_probe(struct ata_port
if (!found)
goto err_out_disable;
- ata_set_mode(ap);
+ if (ap->ops->set_mode)
+ ap->ops->set_mode(ap);
+ else
+ ata_set_mode(ap);
+
if (ap->flags & ATA_FLAG_PORT_DISABLED)
goto err_out_disable;
@@ -1845,7 +1820,7 @@ static void ata_host_set_dma(struct ata_
*/
static void ata_set_mode(struct ata_port *ap)
{
- int i, rc;
+ int i, rc, used_dma = 0;
/* step 1: calculate xfer_mask */
for (i = 0; i < ATA_MAX_DEVICES; i++) {
@@ -1863,6 +1838,9 @@ static void ata_set_mode(struct ata_port
dma_mask = ata_pack_xfermask(0, dev->mwdma_mask, dev->udma_mask);
dev->pio_mode = ata_xfer_mask2mode(pio_mask);
dev->dma_mode = ata_xfer_mask2mode(dma_mask);
+
+ if (dev->dma_mode)
+ used_dma = 1;
}
/* step 2: always set host PIO timings */
@@ -1884,6 +1862,17 @@ static void ata_set_mode(struct ata_port
goto err_out;
}
+ /*
+ * Record simplex status. If we selected DMA then the other
+ * host channels are not permitted to do so.
+ */
+
+ if (used_dma && (ap->host_set->flags & ATA_HOST_SIMPLEX))
+ ap->host_set->simplex_claimed = 1;
+
+ /*
+ * Chip specific finalisation
+ */
if (ap->ops->post_set_mode)
ap->ops->post_set_mode(ap);
@@ -2005,45 +1994,6 @@ static void ata_bus_post_reset(struct at
ap->ops->dev_select(ap, 0);
}
-/**
- * ata_bus_edd - Issue EXECUTE DEVICE DIAGNOSTIC command.
- * @ap: Port to reset and probe
- *
- * Use the EXECUTE DEVICE DIAGNOSTIC command to reset and
- * probe the bus. Not often used these days.
- *
- * LOCKING:
- * PCI/etc. bus probe sem.
- * Obtains host_set lock.
- *
- */
-
-static unsigned int ata_bus_edd(struct ata_port *ap)
-{
- struct ata_taskfile tf;
- unsigned long flags;
-
- /* set up execute-device-diag (bus reset) taskfile */
- /* also, take interrupts to a known state (disabled) */
- DPRINTK("execute-device-diag\n");
- ata_tf_init(ap, &tf, 0);
- tf.ctl |= ATA_NIEN;
- tf.command = ATA_CMD_EDD;
- tf.protocol = ATA_PROT_NODATA;
-
- /* do bus reset */
- spin_lock_irqsave(&ap->host_set->lock, flags);
- ata_tf_to_host(ap, &tf);
- spin_unlock_irqrestore(&ap->host_set->lock, flags);
-
- /* spec says at least 2ms. but who knows with those
- * crazy ATAPI devices...
- */
- msleep(150);
-
- return ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);
-}
-
static unsigned int ata_bus_softreset(struct ata_port *ap,
unsigned int devmask)
{
@@ -2078,13 +2028,12 @@ static unsigned int ata_bus_softreset(st
*/
msleep(150);
-
/* Before we perform post reset processing we want to see if
- the bus shows 0xFF because the odd clown forgets the D7 pulldown
- resistor */
-
+ * the bus shows 0xFF because the odd clown forgets the D7
+ * pulldown resistor.
+ */
if (ata_check_status(ap) == 0xFF)
- return 1; /* Positive is failure for some reason */
+ return AC_ERR_OTHER;
ata_bus_post_reset(ap, devmask);
@@ -2116,7 +2065,7 @@ void ata_bus_reset(struct ata_port *ap)
struct ata_ioports *ioaddr = &ap->ioaddr;
unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
u8 err;
- unsigned int dev0, dev1 = 0, rc = 0, devmask = 0;
+ unsigned int dev0, dev1 = 0, devmask = 0;
DPRINTK("ENTER, host %u, port %u\n", ap->id, ap->port_no);
@@ -2139,18 +2088,8 @@ void ata_bus_reset(struct ata_port *ap)
/* issue bus reset */
if (ap->flags & ATA_FLAG_SRST)
- rc = ata_bus_softreset(ap, devmask);
- else if ((ap->flags & ATA_FLAG_SATA_RESET) == 0) {
- /* set up device control */
- if (ap->flags & ATA_FLAG_MMIO)
- writeb(ap->ctl, (void __iomem *) ioaddr->ctl_addr);
- else
- outb(ap->ctl, ioaddr->ctl_addr);
- rc = ata_bus_edd(ap);
- }
-
- if (rc)
- goto err_out;
+ if (ata_bus_softreset(ap, devmask))
+ goto err_out;
/*
* determine by signature whether we have ATA or ATAPI devices
@@ -2223,9 +2162,9 @@ static int sata_phy_resume(struct ata_po
* so makes reset sequence different from the original
* ->phy_reset implementation and Jeff nervous. :-P
*/
-extern void ata_std_probeinit(struct ata_port *ap)
+void ata_std_probeinit(struct ata_port *ap)
{
- if (ap->flags & ATA_FLAG_SATA && ap->ops->scr_read) {
+ if ((ap->flags & ATA_FLAG_SATA) && ap->ops->scr_read) {
sata_phy_resume(ap);
if (sata_dev_present(ap))
ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);
@@ -2714,18 +2653,23 @@ static int ata_dma_blacklisted(const str
* known limits including host controller limits, device
* blacklist, etc...
*
+ * FIXME: The current implementation limits all transfer modes to
+ * the fastest of the lowested device on the port. This is not
+ * required on most controllers.
+ *
* LOCKING:
* None.
*/
static void ata_dev_xfermask(struct ata_port *ap, struct ata_device *dev)
{
+ struct ata_host_set *hs = ap->host_set;
unsigned long xfer_mask;
int i;
xfer_mask = ata_pack_xfermask(ap->pio_mask, ap->mwdma_mask,
ap->udma_mask);
- /* use port-wide xfermask for now */
+ /* FIXME: Use port-wide xfermask for now */
for (i = 0; i < ATA_MAX_DEVICES; i++) {
struct ata_device *d = &ap->device[i];
if (!ata_dev_present(d))
@@ -2735,12 +2679,23 @@ static void ata_dev_xfermask(struct ata_
xfer_mask &= ata_id_xfermask(d->id);
if (ata_dma_blacklisted(d))
xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
+ /* Apply cable rule here. Don't apply it early because when
+ we handle hot plug the cable type can itself change */
+ if (ap->cbl == ATA_CBL_PATA40)
+ xfer_mask &= ~(0xF8 << ATA_SHIFT_UDMA);
}
if (ata_dma_blacklisted(dev))
printk(KERN_WARNING "ata%u: dev %u is on DMA blacklist, "
"disabling DMA\n", ap->id, dev->devno);
+ if (hs->flags & ATA_HOST_SIMPLEX) {
+ if (hs->simplex_claimed)
+ xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
+ }
+ if (ap->ops->mode_filter)
+ xfer_mask = ap->ops->mode_filter(ap, dev, xfer_mask);
+
ata_unpack_xfermask(xfer_mask, &dev->pio_mask, &dev->mwdma_mask,
&dev->udma_mask);
}
@@ -2795,16 +2750,16 @@ static unsigned int ata_dev_set_xfermode
*/
static unsigned int ata_dev_init_params(struct ata_port *ap,
- struct ata_device *dev)
+ struct ata_device *dev,
+ u16 heads,
+ u16 sectors)
{
struct ata_taskfile tf;
unsigned int err_mask;
- u16 sectors = dev->id[6];
- u16 heads = dev->id[3];
/* Number of sectors per track 1-255. Number of heads 1-16 */
if (sectors < 1 || sectors > 255 || heads < 1 || heads > 16)
- return 0;
+ return AC_ERR_INVALID;
/* set up init dev params taskfile */
DPRINTK("init dev params \n");
@@ -4536,6 +4491,14 @@ static struct ata_port * ata_host_add(co
int rc;
DPRINTK("ENTER\n");
+
+ if (!ent->port_ops->probe_reset &&
+ !(ent->host_flags & (ATA_FLAG_SATA_RESET | ATA_FLAG_SRST))) {
+ printk(KERN_ERR "ata%u: no reset mechanism available\n",
+ port_no);
+ return NULL;
+ }
+
host = scsi_host_alloc(ent->sht, sizeof(struct ata_port));
if (!host)
return NULL;
@@ -4596,6 +4559,7 @@ int ata_device_add(const struct ata_prob
host_set->mmio_base = ent->mmio_base;
host_set->private_data = ent->private_data;
host_set->ops = ent->port_ops;
+ host_set->flags = ent->host_set_flags;
/* register each port bound to this device */
for (i = 0; i < ent->n_ports; i++) {
diff --git a/drivers/scsi/sata_mv.c b/drivers/scsi/sata_mv.c
index 275ed9b..fa901fd 100644
--- a/drivers/scsi/sata_mv.c
+++ b/drivers/scsi/sata_mv.c
@@ -1010,7 +1010,7 @@ static void mv_fill_sg(struct ata_queued
pp->sg_tbl[i].addr = cpu_to_le32(addr & 0xffffffff);
pp->sg_tbl[i].addr_hi = cpu_to_le32((addr >> 16) >> 16);
- pp->sg_tbl[i].flags_size = cpu_to_le32(len);
+ pp->sg_tbl[i].flags_size = cpu_to_le32(len & 0xffff);
sg_len -= len;
addr += len;
@@ -1350,7 +1350,6 @@ static void mv_host_intr(struct ata_host
{
void __iomem *mmio = host_set->mmio_base;
void __iomem *hc_mmio = mv_hc_base(mmio, hc);
- struct ata_port *ap;
struct ata_queued_cmd *qc;
u32 hc_irq_cause;
int shift, port, port0, hard_port, handled;
@@ -1373,25 +1372,32 @@ static void mv_host_intr(struct ata_host
for (port = port0; port < port0 + MV_PORTS_PER_HC; port++) {
u8 ata_status = 0;
- ap = host_set->ports[port];
+ struct ata_port *ap = host_set->ports[port];
+ struct mv_port_priv *pp = ap->private_data;
+
hard_port = port & MV_PORT_MASK; /* range 0-3 */
handled = 0; /* ensure ata_status is set if handled++ */
- if ((CRPB_DMA_DONE << hard_port) & hc_irq_cause) {
- /* new CRPB on the queue; just one at a time until NCQ
- */
- ata_status = mv_get_crpb_status(ap);
- handled++;
- } else if ((DEV_IRQ << hard_port) & hc_irq_cause) {
- /* received ATA IRQ; read the status reg to clear INTRQ
- */
- ata_status = readb((void __iomem *)
+ /* Note that DEV_IRQ might happen spuriously during EDMA,
+ * and should be ignored in such cases. We could mask it,
+ * but it's pretty rare and may not be worth the overhead.
+ */
+ if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) {
+ /* EDMA: check for response queue interrupt */
+ if ((CRPB_DMA_DONE << hard_port) & hc_irq_cause) {
+ ata_status = mv_get_crpb_status(ap);
+ handled = 1;
+ }
+ } else {
+ /* PIO: check for device (drive) interrupt */
+ if ((DEV_IRQ << hard_port) & hc_irq_cause) {
+ ata_status = readb((void __iomem *)
ap->ioaddr.status_addr);
- handled++;
+ handled = 1;
+ }
}
- if (ap &&
- (ap->flags & (ATA_FLAG_PORT_DISABLED | ATA_FLAG_NOINTR)))
+ if (ap->flags & (ATA_FLAG_PORT_DISABLED | ATA_FLAG_NOINTR))
continue;
err_mask = ac_err_mask(ata_status);
@@ -1403,12 +1409,12 @@ static void mv_host_intr(struct ata_host
if ((PORT0_ERR << shift) & relevant) {
mv_err_intr(ap);
err_mask |= AC_ERR_OTHER;
- handled++;
+ handled = 1;
}
- if (handled && ap) {
+ if (handled) {
qc = ata_qc_from_tag(ap, ap->active_tag);
- if (NULL != qc) {
+ if (qc && (qc->flags & ATA_QCFLAG_ACTIVE)) {
VPRINTK("port %u IRQ found for qc, "
"ata_status 0x%x\n", port,ata_status);
/* mark qc status appropriately */
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 0471922..0d61357 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -160,8 +160,10 @@ enum {
ATA_QCFLAG_DMAMAP = ATA_QCFLAG_SG | ATA_QCFLAG_SINGLE,
ATA_QCFLAG_EH_SCHEDULED = (1 << 5), /* EH scheduled */
+ /* host set flags */
+ ATA_HOST_SIMPLEX = (1 << 0), /* Host is simplex, one DMA channel per host_set only */
+
/* various lengths of time */
- ATA_TMOUT_EDD = 5 * HZ, /* heuristic */
ATA_TMOUT_PIO = 30 * HZ,
ATA_TMOUT_BOOT = 30 * HZ, /* heuristic */
ATA_TMOUT_BOOT_QUICK = 7 * HZ, /* heuristic */
@@ -279,6 +281,7 @@ struct ata_probe_ent {
unsigned long irq;
unsigned int irq_flags;
unsigned long host_flags;
+ unsigned long host_set_flags;
void __iomem *mmio_base;
void *private_data;
};
@@ -291,6 +294,9 @@ struct ata_host_set {
unsigned int n_ports;
void *private_data;
const struct ata_port_operations *ops;
+ unsigned long flags;
+ int simplex_claimed; /* Keep seperate in case we
+ ever need to do this locked */
struct ata_port * ports[0];
};
@@ -420,6 +426,7 @@ struct ata_port_operations {
void (*set_piomode) (struct ata_port *, struct ata_device *);
void (*set_dmamode) (struct ata_port *, struct ata_device *);
+ unsigned long (*mode_filter) (const struct ata_port *, struct ata_device *, unsigned long);
void (*tf_load) (struct ata_port *ap, const struct ata_taskfile *tf);
void (*tf_read) (struct ata_port *ap, struct ata_taskfile *tf);
@@ -430,6 +437,7 @@ struct ata_port_operations {
void (*dev_select)(struct ata_port *ap, unsigned int device);
void (*phy_reset) (struct ata_port *ap); /* obsolete */
+ void (*set_mode) (struct ata_port *ap);
int (*probe_reset) (struct ata_port *ap, unsigned int *classes);
void (*post_set_mode) (struct ata_port *ap);
^ permalink raw reply related [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2006-03-24 15:59 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2006-03-24 15:59 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, linux-kernel
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git
to receive the following updates:
drivers/scsi/ata_piix.c | 6
drivers/scsi/libata-bmdma.c | 238 ++++++++++++++++++++++
drivers/scsi/libata-core.c | 469 +++++++++++++++-----------------------------
drivers/scsi/libata-scsi.c | 79 +++----
drivers/scsi/sata_nv.c | 181 +++++-----------
drivers/scsi/sata_sil.c | 2
drivers/scsi/sata_sil24.c | 25 +-
drivers/scsi/sata_uli.c | 37 ++-
drivers/scsi/sata_vsc.c | 4
drivers/scsi/scsi_sysfs.c | 2
include/linux/libata.h | 12 -
include/scsi/scsi_host.h | 2
12 files changed, 551 insertions(+), 506 deletions(-)
Alan Cox:
libata: add ata_dev_pair helper
Brian King:
libata: ata_scsi_queuecmd cleanup
libata: ata_scsi_ioctl cleanup
libata: Remove dependence on host_set->dev for SAS
Jeff Garzik:
[libata sata_sil24] cleanups: use pci_iomap(), kzalloc()
[libata sata_nv] cleanups: convert #defines to enums; remove in-file history
[libata sata_nv] eliminate duplicate codepaths with iomap
[libata sata_uli] kill scr_addr abuse
[libata] Move some bmdma-specific code to libata-bmdma.c
[libata] export ata_dev_pair; trim trailing whitespace
Nigel Cunningham:
Make libata not powerdown drivers on PM_EVENT_FREEZE.
Tejun Heo:
libata: implement ata_unpack_xfermask()
libata: add per-dev pio/mwdma/udma_mask
libata: make per-dev transfer mode limits per-dev
libata: check if port is disabled after internal command
libata: implement ata_dev_disable()
libata: use ata_dev_disable() in ata_bus_probe()
libata: make ata_set_mode() responsible for failure handling
diff --git a/drivers/scsi/ata_piix.c b/drivers/scsi/ata_piix.c
index a74e23d..2d5be84 100644
--- a/drivers/scsi/ata_piix.c
+++ b/drivers/scsi/ata_piix.c
@@ -742,7 +742,7 @@ static int piix_disable_ahci(struct pci_
/**
* piix_check_450nx_errata - Check for problem 450NX setup
* @ata_dev: the PCI device to check
- *
+ *
* Check for the present of 450NX errata #19 and errata #25. If
* they are found return an error code so we can turn off DMA
*/
@@ -753,7 +753,7 @@ static int __devinit piix_check_450nx_er
u16 cfg;
u8 rev;
int no_piix_dma = 0;
-
+
while((pdev = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev)) != NULL)
{
/* Look for 450NX PXB. Check for problem configurations
@@ -772,7 +772,7 @@ static int __devinit piix_check_450nx_er
if(no_piix_dma == 2)
dev_printk(KERN_WARNING, &ata_dev->dev, "A BIOS update may resolve this.\n");
return no_piix_dma;
-}
+}
static void __devinit piix_init_sata_map(struct pci_dev *pdev,
struct ata_port_info *pinfo)
diff --git a/drivers/scsi/libata-bmdma.c b/drivers/scsi/libata-bmdma.c
index 96b4d21..95d81d8 100644
--- a/drivers/scsi/libata-bmdma.c
+++ b/drivers/scsi/libata-bmdma.c
@@ -418,6 +418,240 @@ u8 ata_altstatus(struct ata_port *ap)
return inb(ap->ioaddr.altstatus_addr);
}
+/**
+ * ata_bmdma_setup_mmio - Set up PCI IDE BMDMA transaction
+ * @qc: Info associated with this ATA transaction.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host_set lock)
+ */
+
+static void ata_bmdma_setup_mmio (struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
+ u8 dmactl;
+ void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
+
+ /* load PRD table addr. */
+ mb(); /* make sure PRD table writes are visible to controller */
+ writel(ap->prd_dma, mmio + ATA_DMA_TABLE_OFS);
+
+ /* specify data direction, triple-check start bit is clear */
+ dmactl = readb(mmio + ATA_DMA_CMD);
+ dmactl &= ~(ATA_DMA_WR | ATA_DMA_START);
+ if (!rw)
+ dmactl |= ATA_DMA_WR;
+ writeb(dmactl, mmio + ATA_DMA_CMD);
+
+ /* issue r/w command */
+ ap->ops->exec_command(ap, &qc->tf);
+}
+
+/**
+ * ata_bmdma_start_mmio - Start a PCI IDE BMDMA transaction
+ * @qc: Info associated with this ATA transaction.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host_set lock)
+ */
+
+static void ata_bmdma_start_mmio (struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
+ u8 dmactl;
+
+ /* start host DMA transaction */
+ dmactl = readb(mmio + ATA_DMA_CMD);
+ writeb(dmactl | ATA_DMA_START, mmio + ATA_DMA_CMD);
+
+ /* Strictly, one may wish to issue a readb() here, to
+ * flush the mmio write. However, control also passes
+ * to the hardware at this point, and it will interrupt
+ * us when we are to resume control. So, in effect,
+ * we don't care when the mmio write flushes.
+ * Further, a read of the DMA status register _immediately_
+ * following the write may not be what certain flaky hardware
+ * is expected, so I think it is best to not add a readb()
+ * without first all the MMIO ATA cards/mobos.
+ * Or maybe I'm just being paranoid.
+ */
+}
+
+/**
+ * ata_bmdma_setup_pio - Set up PCI IDE BMDMA transaction (PIO)
+ * @qc: Info associated with this ATA transaction.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host_set lock)
+ */
+
+static void ata_bmdma_setup_pio (struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
+ u8 dmactl;
+
+ /* load PRD table addr. */
+ outl(ap->prd_dma, ap->ioaddr.bmdma_addr + ATA_DMA_TABLE_OFS);
+
+ /* specify data direction, triple-check start bit is clear */
+ dmactl = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+ dmactl &= ~(ATA_DMA_WR | ATA_DMA_START);
+ if (!rw)
+ dmactl |= ATA_DMA_WR;
+ outb(dmactl, ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+
+ /* issue r/w command */
+ ap->ops->exec_command(ap, &qc->tf);
+}
+
+/**
+ * ata_bmdma_start_pio - Start a PCI IDE BMDMA transaction (PIO)
+ * @qc: Info associated with this ATA transaction.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host_set lock)
+ */
+
+static void ata_bmdma_start_pio (struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ u8 dmactl;
+
+ /* start host DMA transaction */
+ dmactl = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+ outb(dmactl | ATA_DMA_START,
+ ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+}
+
+
+/**
+ * ata_bmdma_start - Start a PCI IDE BMDMA transaction
+ * @qc: Info associated with this ATA transaction.
+ *
+ * Writes the ATA_DMA_START flag to the DMA command register.
+ *
+ * May be used as the bmdma_start() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host_set lock)
+ */
+void ata_bmdma_start(struct ata_queued_cmd *qc)
+{
+ if (qc->ap->flags & ATA_FLAG_MMIO)
+ ata_bmdma_start_mmio(qc);
+ else
+ ata_bmdma_start_pio(qc);
+}
+
+
+/**
+ * ata_bmdma_setup - Set up PCI IDE BMDMA transaction
+ * @qc: Info associated with this ATA transaction.
+ *
+ * Writes address of PRD table to device's PRD Table Address
+ * register, sets the DMA control register, and calls
+ * ops->exec_command() to start the transfer.
+ *
+ * May be used as the bmdma_setup() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host_set lock)
+ */
+void ata_bmdma_setup(struct ata_queued_cmd *qc)
+{
+ if (qc->ap->flags & ATA_FLAG_MMIO)
+ ata_bmdma_setup_mmio(qc);
+ else
+ ata_bmdma_setup_pio(qc);
+}
+
+
+/**
+ * ata_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt.
+ * @ap: Port associated with this ATA transaction.
+ *
+ * Clear interrupt and error flags in DMA status register.
+ *
+ * May be used as the irq_clear() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host_set lock)
+ */
+
+void ata_bmdma_irq_clear(struct ata_port *ap)
+{
+ if (!ap->ioaddr.bmdma_addr)
+ return;
+
+ if (ap->flags & ATA_FLAG_MMIO) {
+ void __iomem *mmio =
+ ((void __iomem *) ap->ioaddr.bmdma_addr) + ATA_DMA_STATUS;
+ writeb(readb(mmio), mmio);
+ } else {
+ unsigned long addr = ap->ioaddr.bmdma_addr + ATA_DMA_STATUS;
+ outb(inb(addr), addr);
+ }
+}
+
+
+/**
+ * ata_bmdma_status - Read PCI IDE BMDMA status
+ * @ap: Port associated with this ATA transaction.
+ *
+ * Read and return BMDMA status register.
+ *
+ * May be used as the bmdma_status() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host_set lock)
+ */
+
+u8 ata_bmdma_status(struct ata_port *ap)
+{
+ u8 host_stat;
+ if (ap->flags & ATA_FLAG_MMIO) {
+ void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
+ host_stat = readb(mmio + ATA_DMA_STATUS);
+ } else
+ host_stat = inb(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+ return host_stat;
+}
+
+
+/**
+ * ata_bmdma_stop - Stop PCI IDE BMDMA transfer
+ * @qc: Command we are ending DMA for
+ *
+ * Clears the ATA_DMA_START flag in the dma control register
+ *
+ * May be used as the bmdma_stop() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host_set lock)
+ */
+
+void ata_bmdma_stop(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ if (ap->flags & ATA_FLAG_MMIO) {
+ void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
+
+ /* clear start/stop bit */
+ writeb(readb(mmio + ATA_DMA_CMD) & ~ATA_DMA_START,
+ mmio + ATA_DMA_CMD);
+ } else {
+ /* clear start/stop bit */
+ outb(inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD) & ~ATA_DMA_START,
+ ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+ }
+
+ /* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */
+ ata_altstatus(ap); /* dummy read */
+}
+
#ifdef CONFIG_PCI
static struct ata_probe_ent *
ata_probe_ent_alloc(struct device *dev, const struct ata_port_info *port)
@@ -707,7 +941,7 @@ err_out:
* @pdev: PCI device
*
* Some PCI ATA devices report simplex mode but in fact can be told to
- * enter non simplex mode. This implements the neccessary logic to
+ * enter non simplex mode. This implements the neccessary logic to
* perform the task on such devices. Calling it on other devices will
* have -undefined- behaviour.
*/
@@ -732,7 +966,7 @@ unsigned long ata_pci_default_filter(con
{
/* Filter out DMA modes if the device has been configured by
the BIOS as PIO only */
-
+
if (ap->ioaddr.bmdma_addr == 0)
xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
return xfer_mask;
diff --git a/drivers/scsi/libata-core.c b/drivers/scsi/libata-core.c
index 0314abd..d279666 100644
--- a/drivers/scsi/libata-core.c
+++ b/drivers/scsi/libata-core.c
@@ -64,9 +64,9 @@
static unsigned int ata_dev_init_params(struct ata_port *ap,
struct ata_device *dev);
static void ata_set_mode(struct ata_port *ap);
-static void ata_dev_set_xfermode(struct ata_port *ap, struct ata_device *dev);
-static unsigned int ata_dev_xfermask(struct ata_port *ap,
- struct ata_device *dev);
+static unsigned int ata_dev_set_xfermode(struct ata_port *ap,
+ struct ata_device *dev);
+static void ata_dev_xfermask(struct ata_port *ap, struct ata_device *dev);
static unsigned int ata_unique_id = 1;
static struct workqueue_struct *ata_wq;
@@ -190,7 +190,7 @@ static const u8 ata_rw_cmds[] = {
* ata_rwcmd_protocol - set taskfile r/w commands and protocol
* @qc: command to examine and configure
*
- * Examine the device configuration and tf->flags to calculate
+ * Examine the device configuration and tf->flags to calculate
* the proper read/write commands and protocol to use.
*
* LOCKING:
@@ -203,7 +203,7 @@ int ata_rwcmd_protocol(struct ata_queued
u8 cmd;
int index, fua, lba48, write;
-
+
fua = (tf->flags & ATA_TFLAG_FUA) ? 4 : 0;
lba48 = (tf->flags & ATA_TFLAG_LBA48) ? 2 : 0;
write = (tf->flags & ATA_TFLAG_WRITE) ? 1 : 0;
@@ -252,6 +252,29 @@ static unsigned int ata_pack_xfermask(un
((udma_mask << ATA_SHIFT_UDMA) & ATA_MASK_UDMA);
}
+/**
+ * ata_unpack_xfermask - Unpack xfer_mask into pio, mwdma and udma masks
+ * @xfer_mask: xfer_mask to unpack
+ * @pio_mask: resulting pio_mask
+ * @mwdma_mask: resulting mwdma_mask
+ * @udma_mask: resulting udma_mask
+ *
+ * Unpack @xfer_mask into @pio_mask, @mwdma_mask and @udma_mask.
+ * Any NULL distination masks will be ignored.
+ */
+static void ata_unpack_xfermask(unsigned int xfer_mask,
+ unsigned int *pio_mask,
+ unsigned int *mwdma_mask,
+ unsigned int *udma_mask)
+{
+ if (pio_mask)
+ *pio_mask = (xfer_mask & ATA_MASK_PIO) >> ATA_SHIFT_PIO;
+ if (mwdma_mask)
+ *mwdma_mask = (xfer_mask & ATA_MASK_MWDMA) >> ATA_SHIFT_MWDMA;
+ if (udma_mask)
+ *udma_mask = (xfer_mask & ATA_MASK_UDMA) >> ATA_SHIFT_UDMA;
+}
+
static const struct ata_xfer_ent {
unsigned int shift, bits;
u8 base;
@@ -372,6 +395,15 @@ static const char *ata_mode_string(unsig
return "<n/a>";
}
+static void ata_dev_disable(struct ata_port *ap, struct ata_device *dev)
+{
+ if (ata_dev_present(dev)) {
+ printk(KERN_WARNING "ata%u: dev %u disabled\n",
+ ap->id, dev->devno);
+ dev->class++;
+ }
+}
+
/**
* ata_pio_devchk - PATA device presence detection
* @ap: ATA channel to examine
@@ -987,6 +1019,22 @@ ata_exec_internal(struct ata_port *ap, s
ata_qc_free(qc);
+ /* XXX - Some LLDDs (sata_mv) disable port on command failure.
+ * Until those drivers are fixed, we detect the condition
+ * here, fail the command with AC_ERR_SYSTEM and reenable the
+ * port.
+ *
+ * Note that this doesn't change any behavior as internal
+ * command failure results in disabling the device in the
+ * higher layer for LLDDs without new reset/EH callbacks.
+ *
+ * Kill the following code as soon as those drivers are fixed.
+ */
+ if (ap->flags & ATA_FLAG_PORT_DISABLED) {
+ err_mask |= AC_ERR_SYSTEM;
+ ata_port_probe(ap);
+ }
+
return err_mask;
}
@@ -1007,7 +1055,7 @@ unsigned int ata_pio_need_iordy(const st
return 0;
if (speed > 2)
return 1;
-
+
/* If we have no drive specific rule, then PIO 2 is non IORDY */
if (adev->id[ATA_ID_FIELD_VALID] & 2) { /* EIDE */
@@ -1305,7 +1353,7 @@ static int ata_dev_configure(struct ata_
if (print_info)
printk(KERN_INFO "ata%u(%u): applying bridge limits\n",
ap->id, dev->devno);
- ap->udma_mask &= ATA_UDMA5;
+ dev->udma_mask &= ATA_UDMA5;
dev->max_sectors = ATA_MAX_SECTORS;
}
@@ -1316,8 +1364,6 @@ static int ata_dev_configure(struct ata_
return 0;
err_out_nosup:
- printk(KERN_WARNING "ata%u: dev %u not supported, ignoring\n",
- ap->id, dev->devno);
DPRINTK("EXIT, err\n");
return rc;
}
@@ -1384,7 +1430,7 @@ static int ata_bus_probe(struct ata_port
}
if (ata_dev_configure(ap, dev, 1)) {
- dev->class++; /* disable device */
+ ata_dev_disable(ap, dev);
continue;
}
@@ -1530,6 +1576,23 @@ void sata_phy_reset(struct ata_port *ap)
}
/**
+ * ata_dev_pair - return other device on cable
+ * @ap: port
+ * @adev: device
+ *
+ * Obtain the other device on the same cable, or if none is
+ * present NULL is returned
+ */
+
+struct ata_device *ata_dev_pair(struct ata_port *ap, struct ata_device *adev)
+{
+ struct ata_device *pair = &ap->device[1 - adev->devno];
+ if (!ata_dev_present(pair))
+ return NULL;
+ return pair;
+}
+
+/**
* ata_port_disable - Disable port.
* @ap: Port to be disabled.
*
@@ -1557,7 +1620,7 @@ void ata_port_disable(struct ata_port *a
* PIO 0-5, MWDMA 0-2 and UDMA 0-6 timings (in nanoseconds).
* These were taken from ATA/ATAPI-6 standard, rev 0a, except
* for PIO 5, which is a nonstandard extension and UDMA6, which
- * is currently supported only by Maxtor drives.
+ * is currently supported only by Maxtor drives.
*/
static const struct ata_timing ata_timing[] = {
@@ -1572,11 +1635,11 @@ static const struct ata_timing ata_timin
{ XFER_UDMA_0, 0, 0, 0, 0, 0, 0, 0, 120 },
/* { XFER_UDMA_SLOW, 0, 0, 0, 0, 0, 0, 0, 150 }, */
-
+
{ XFER_MW_DMA_2, 25, 0, 0, 0, 70, 25, 120, 0 },
{ XFER_MW_DMA_1, 45, 0, 0, 0, 80, 50, 150, 0 },
{ XFER_MW_DMA_0, 60, 0, 0, 0, 215, 215, 480, 0 },
-
+
{ XFER_SW_DMA_2, 60, 0, 0, 0, 120, 120, 240, 0 },
{ XFER_SW_DMA_1, 90, 0, 0, 0, 240, 240, 480, 0 },
{ XFER_SW_DMA_0, 120, 0, 0, 0, 480, 480, 960, 0 },
@@ -1629,7 +1692,7 @@ static const struct ata_timing* ata_timi
for (t = ata_timing; t->mode != speed; t++)
if (t->mode == 0xFF)
return NULL;
- return t;
+ return t;
}
int ata_timing_compute(struct ata_device *adev, unsigned short speed,
@@ -1639,7 +1702,7 @@ int ata_timing_compute(struct ata_device
struct ata_timing p;
/*
- * Find the mode.
+ * Find the mode.
*/
if (!(s = ata_timing_find_mode(speed)))
@@ -1697,20 +1760,28 @@ int ata_timing_compute(struct ata_device
return 0;
}
-static void ata_dev_set_mode(struct ata_port *ap, struct ata_device *dev)
+static int ata_dev_set_mode(struct ata_port *ap, struct ata_device *dev)
{
- if (!ata_dev_present(dev) || (ap->flags & ATA_FLAG_PORT_DISABLED))
- return;
+ unsigned int err_mask;
+ int rc;
if (dev->xfer_shift == ATA_SHIFT_PIO)
dev->flags |= ATA_DFLAG_PIO;
- ata_dev_set_xfermode(ap, dev);
+ err_mask = ata_dev_set_xfermode(ap, dev);
+ if (err_mask) {
+ printk(KERN_ERR
+ "ata%u: failed to set xfermode (err_mask=0x%x)\n",
+ ap->id, err_mask);
+ return -EIO;
+ }
- if (ata_dev_revalidate(ap, dev, 0)) {
- printk(KERN_ERR "ata%u: failed to revalidate after set "
- "xfermode, disabled\n", ap->id);
- ata_port_disable(ap);
+ rc = ata_dev_revalidate(ap, dev, 0);
+ if (rc) {
+ printk(KERN_ERR
+ "ata%u: failed to revalidate after set xfermode\n",
+ ap->id);
+ return rc;
}
DPRINTK("xfer_shift=%u, xfer_mode=0x%x\n",
@@ -1719,6 +1790,7 @@ static void ata_dev_set_mode(struct ata_
printk(KERN_INFO "ata%u: dev %u configured for %s\n",
ap->id, dev->devno,
ata_mode_string(ata_xfer_mode2mask(dev->xfer_mode)));
+ return 0;
}
static int ata_host_set_pio(struct ata_port *ap)
@@ -1778,16 +1850,19 @@ static void ata_set_mode(struct ata_port
/* step 1: calculate xfer_mask */
for (i = 0; i < ATA_MAX_DEVICES; i++) {
struct ata_device *dev = &ap->device[i];
- unsigned int xfer_mask;
+ unsigned int pio_mask, dma_mask;
if (!ata_dev_present(dev))
continue;
- xfer_mask = ata_dev_xfermask(ap, dev);
+ ata_dev_xfermask(ap, dev);
- dev->pio_mode = ata_xfer_mask2mode(xfer_mask & ATA_MASK_PIO);
- dev->dma_mode = ata_xfer_mask2mode(xfer_mask & (ATA_MASK_MWDMA |
- ATA_MASK_UDMA));
+ /* TODO: let LLDD filter dev->*_mask here */
+
+ pio_mask = ata_pack_xfermask(dev->pio_mask, 0, 0);
+ dma_mask = ata_pack_xfermask(0, dev->mwdma_mask, dev->udma_mask);
+ dev->pio_mode = ata_xfer_mask2mode(pio_mask);
+ dev->dma_mode = ata_xfer_mask2mode(dma_mask);
}
/* step 2: always set host PIO timings */
@@ -1799,11 +1874,15 @@ static void ata_set_mode(struct ata_port
ata_host_set_dma(ap);
/* step 4: update devices' xfer mode */
- for (i = 0; i < ATA_MAX_DEVICES; i++)
- ata_dev_set_mode(ap, &ap->device[i]);
+ for (i = 0; i < ATA_MAX_DEVICES; i++) {
+ struct ata_device *dev = &ap->device[i];
- if (ap->flags & ATA_FLAG_PORT_DISABLED)
- return;
+ if (!ata_dev_present(dev))
+ continue;
+
+ if (ata_dev_set_mode(ap, dev))
+ goto err_out;
+ }
if (ap->ops->post_set_mode)
ap->ops->post_set_mode(ap);
@@ -1999,11 +2078,11 @@ static unsigned int ata_bus_softreset(st
*/
msleep(150);
-
- /* Before we perform post reset processing we want to see if
+
+ /* Before we perform post reset processing we want to see if
the bus shows 0xFF because the odd clown forgets the D7 pulldown
resistor */
-
+
if (ata_check_status(ap) == 0xFF)
return 1; /* Positive is failure for some reason */
@@ -2572,22 +2651,22 @@ static const char * const ata_dma_blackl
"SanDisk SDP3B-64", NULL,
"SANYO CD-ROM CRD", NULL,
"HITACHI CDR-8", NULL,
- "HITACHI CDR-8335", NULL,
+ "HITACHI CDR-8335", NULL,
"HITACHI CDR-8435", NULL,
- "Toshiba CD-ROM XM-6202B", NULL,
- "TOSHIBA CD-ROM XM-1702BC", NULL,
- "CD-532E-A", NULL,
- "E-IDE CD-ROM CR-840", NULL,
- "CD-ROM Drive/F5A", NULL,
- "WPI CDD-820", NULL,
+ "Toshiba CD-ROM XM-6202B", NULL,
+ "TOSHIBA CD-ROM XM-1702BC", NULL,
+ "CD-532E-A", NULL,
+ "E-IDE CD-ROM CR-840", NULL,
+ "CD-ROM Drive/F5A", NULL,
+ "WPI CDD-820", NULL,
"SAMSUNG CD-ROM SC-148C", NULL,
- "SAMSUNG CD-ROM SC", NULL,
+ "SAMSUNG CD-ROM SC", NULL,
"SanDisk SDP3B-64", NULL,
"ATAPI CD-ROM DRIVE 40X MAXIMUM",NULL,
"_NEC DV5800A", NULL,
"SAMSUNG CD-ROM SN-124", "N001"
};
-
+
static int ata_strim(char *s, size_t len)
{
len = strnlen(s, len);
@@ -2630,18 +2709,15 @@ static int ata_dma_blacklisted(const str
* @ap: Port on which the device to compute xfermask for resides
* @dev: Device to compute xfermask for
*
- * Compute supported xfermask of @dev. This function is
- * responsible for applying all known limits including host
- * controller limits, device blacklist, etc...
+ * Compute supported xfermask of @dev and store it in
+ * dev->*_mask. This function is responsible for applying all
+ * known limits including host controller limits, device
+ * blacklist, etc...
*
* LOCKING:
* None.
- *
- * RETURNS:
- * Computed xfermask.
*/
-static unsigned int ata_dev_xfermask(struct ata_port *ap,
- struct ata_device *dev)
+static void ata_dev_xfermask(struct ata_port *ap, struct ata_device *dev)
{
unsigned long xfer_mask;
int i;
@@ -2654,6 +2730,8 @@ static unsigned int ata_dev_xfermask(str
struct ata_device *d = &ap->device[i];
if (!ata_dev_present(d))
continue;
+ xfer_mask &= ata_pack_xfermask(d->pio_mask, d->mwdma_mask,
+ d->udma_mask);
xfer_mask &= ata_id_xfermask(d->id);
if (ata_dma_blacklisted(d))
xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
@@ -2663,7 +2741,8 @@ static unsigned int ata_dev_xfermask(str
printk(KERN_WARNING "ata%u: dev %u is on DMA blacklist, "
"disabling DMA\n", ap->id, dev->devno);
- return xfer_mask;
+ ata_unpack_xfermask(xfer_mask, &dev->pio_mask, &dev->mwdma_mask,
+ &dev->udma_mask);
}
/**
@@ -2676,11 +2755,16 @@ static unsigned int ata_dev_xfermask(str
*
* LOCKING:
* PCI/etc. bus probe sem.
+ *
+ * RETURNS:
+ * 0 on success, AC_ERR_* mask otherwise.
*/
-static void ata_dev_set_xfermode(struct ata_port *ap, struct ata_device *dev)
+static unsigned int ata_dev_set_xfermode(struct ata_port *ap,
+ struct ata_device *dev)
{
struct ata_taskfile tf;
+ unsigned int err_mask;
/* set up set-features taskfile */
DPRINTK("set features - xfer mode\n");
@@ -2692,13 +2776,10 @@ static void ata_dev_set_xfermode(struct
tf.protocol = ATA_PROT_NODATA;
tf.nsect = dev->xfer_mode;
- if (ata_exec_internal(ap, dev, &tf, DMA_NONE, NULL, 0)) {
- printk(KERN_ERR "ata%u: failed to set xfermode, disabled\n",
- ap->id);
- ata_port_disable(ap);
- }
+ err_mask = ata_exec_internal(ap, dev, &tf, DMA_NONE, NULL, 0);
- DPRINTK("EXIT\n");
+ DPRINTK("EXIT, err_mask=%x\n", err_mask);
+ return err_mask;
}
/**
@@ -2775,7 +2856,7 @@ static void ata_sg_clean(struct ata_queu
if (qc->flags & ATA_QCFLAG_SG) {
if (qc->n_elem)
- dma_unmap_sg(ap->host_set->dev, sg, qc->n_elem, dir);
+ dma_unmap_sg(ap->dev, sg, qc->n_elem, dir);
/* restore last sg */
sg[qc->orig_n_elem - 1].length += qc->pad_len;
if (pad_buf) {
@@ -2786,7 +2867,7 @@ static void ata_sg_clean(struct ata_queu
}
} else {
if (qc->n_elem)
- dma_unmap_single(ap->host_set->dev,
+ dma_unmap_single(ap->dev,
sg_dma_address(&sg[0]), sg_dma_len(&sg[0]),
dir);
/* restore sg */
@@ -2997,7 +3078,7 @@ static int ata_sg_setup_one(struct ata_q
goto skip_map;
}
- dma_address = dma_map_single(ap->host_set->dev, qc->buf_virt,
+ dma_address = dma_map_single(ap->dev, qc->buf_virt,
sg->length, dir);
if (dma_mapping_error(dma_address)) {
/* restore sg */
@@ -3085,7 +3166,7 @@ static int ata_sg_setup(struct ata_queue
}
dir = qc->dma_dir;
- n_elem = dma_map_sg(ap->host_set->dev, sg, pre_n_elem, dir);
+ n_elem = dma_map_sg(ap->dev, sg, pre_n_elem, dir);
if (n_elem < 1) {
/* restore last sg */
lsg->length += qc->pad_len;
@@ -3616,7 +3697,7 @@ static void ata_pio_error(struct ata_por
if (qc->tf.command != ATA_CMD_PACKET)
printk(KERN_WARNING "ata%u: PIO error\n", ap->id);
- /* make sure qc->err_mask is available to
+ /* make sure qc->err_mask is available to
* know what's wrong and recover
*/
WARN_ON(qc->err_mask == 0);
@@ -4065,240 +4146,6 @@ unsigned int ata_qc_issue_prot(struct at
}
/**
- * ata_bmdma_setup_mmio - Set up PCI IDE BMDMA transaction
- * @qc: Info associated with this ATA transaction.
- *
- * LOCKING:
- * spin_lock_irqsave(host_set lock)
- */
-
-static void ata_bmdma_setup_mmio (struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
- u8 dmactl;
- void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
-
- /* load PRD table addr. */
- mb(); /* make sure PRD table writes are visible to controller */
- writel(ap->prd_dma, mmio + ATA_DMA_TABLE_OFS);
-
- /* specify data direction, triple-check start bit is clear */
- dmactl = readb(mmio + ATA_DMA_CMD);
- dmactl &= ~(ATA_DMA_WR | ATA_DMA_START);
- if (!rw)
- dmactl |= ATA_DMA_WR;
- writeb(dmactl, mmio + ATA_DMA_CMD);
-
- /* issue r/w command */
- ap->ops->exec_command(ap, &qc->tf);
-}
-
-/**
- * ata_bmdma_start_mmio - Start a PCI IDE BMDMA transaction
- * @qc: Info associated with this ATA transaction.
- *
- * LOCKING:
- * spin_lock_irqsave(host_set lock)
- */
-
-static void ata_bmdma_start_mmio (struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
- u8 dmactl;
-
- /* start host DMA transaction */
- dmactl = readb(mmio + ATA_DMA_CMD);
- writeb(dmactl | ATA_DMA_START, mmio + ATA_DMA_CMD);
-
- /* Strictly, one may wish to issue a readb() here, to
- * flush the mmio write. However, control also passes
- * to the hardware at this point, and it will interrupt
- * us when we are to resume control. So, in effect,
- * we don't care when the mmio write flushes.
- * Further, a read of the DMA status register _immediately_
- * following the write may not be what certain flaky hardware
- * is expected, so I think it is best to not add a readb()
- * without first all the MMIO ATA cards/mobos.
- * Or maybe I'm just being paranoid.
- */
-}
-
-/**
- * ata_bmdma_setup_pio - Set up PCI IDE BMDMA transaction (PIO)
- * @qc: Info associated with this ATA transaction.
- *
- * LOCKING:
- * spin_lock_irqsave(host_set lock)
- */
-
-static void ata_bmdma_setup_pio (struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
- u8 dmactl;
-
- /* load PRD table addr. */
- outl(ap->prd_dma, ap->ioaddr.bmdma_addr + ATA_DMA_TABLE_OFS);
-
- /* specify data direction, triple-check start bit is clear */
- dmactl = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
- dmactl &= ~(ATA_DMA_WR | ATA_DMA_START);
- if (!rw)
- dmactl |= ATA_DMA_WR;
- outb(dmactl, ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
-
- /* issue r/w command */
- ap->ops->exec_command(ap, &qc->tf);
-}
-
-/**
- * ata_bmdma_start_pio - Start a PCI IDE BMDMA transaction (PIO)
- * @qc: Info associated with this ATA transaction.
- *
- * LOCKING:
- * spin_lock_irqsave(host_set lock)
- */
-
-static void ata_bmdma_start_pio (struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- u8 dmactl;
-
- /* start host DMA transaction */
- dmactl = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
- outb(dmactl | ATA_DMA_START,
- ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
-}
-
-
-/**
- * ata_bmdma_start - Start a PCI IDE BMDMA transaction
- * @qc: Info associated with this ATA transaction.
- *
- * Writes the ATA_DMA_START flag to the DMA command register.
- *
- * May be used as the bmdma_start() entry in ata_port_operations.
- *
- * LOCKING:
- * spin_lock_irqsave(host_set lock)
- */
-void ata_bmdma_start(struct ata_queued_cmd *qc)
-{
- if (qc->ap->flags & ATA_FLAG_MMIO)
- ata_bmdma_start_mmio(qc);
- else
- ata_bmdma_start_pio(qc);
-}
-
-
-/**
- * ata_bmdma_setup - Set up PCI IDE BMDMA transaction
- * @qc: Info associated with this ATA transaction.
- *
- * Writes address of PRD table to device's PRD Table Address
- * register, sets the DMA control register, and calls
- * ops->exec_command() to start the transfer.
- *
- * May be used as the bmdma_setup() entry in ata_port_operations.
- *
- * LOCKING:
- * spin_lock_irqsave(host_set lock)
- */
-void ata_bmdma_setup(struct ata_queued_cmd *qc)
-{
- if (qc->ap->flags & ATA_FLAG_MMIO)
- ata_bmdma_setup_mmio(qc);
- else
- ata_bmdma_setup_pio(qc);
-}
-
-
-/**
- * ata_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt.
- * @ap: Port associated with this ATA transaction.
- *
- * Clear interrupt and error flags in DMA status register.
- *
- * May be used as the irq_clear() entry in ata_port_operations.
- *
- * LOCKING:
- * spin_lock_irqsave(host_set lock)
- */
-
-void ata_bmdma_irq_clear(struct ata_port *ap)
-{
- if (!ap->ioaddr.bmdma_addr)
- return;
-
- if (ap->flags & ATA_FLAG_MMIO) {
- void __iomem *mmio =
- ((void __iomem *) ap->ioaddr.bmdma_addr) + ATA_DMA_STATUS;
- writeb(readb(mmio), mmio);
- } else {
- unsigned long addr = ap->ioaddr.bmdma_addr + ATA_DMA_STATUS;
- outb(inb(addr), addr);
- }
-}
-
-
-/**
- * ata_bmdma_status - Read PCI IDE BMDMA status
- * @ap: Port associated with this ATA transaction.
- *
- * Read and return BMDMA status register.
- *
- * May be used as the bmdma_status() entry in ata_port_operations.
- *
- * LOCKING:
- * spin_lock_irqsave(host_set lock)
- */
-
-u8 ata_bmdma_status(struct ata_port *ap)
-{
- u8 host_stat;
- if (ap->flags & ATA_FLAG_MMIO) {
- void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
- host_stat = readb(mmio + ATA_DMA_STATUS);
- } else
- host_stat = inb(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
- return host_stat;
-}
-
-
-/**
- * ata_bmdma_stop - Stop PCI IDE BMDMA transfer
- * @qc: Command we are ending DMA for
- *
- * Clears the ATA_DMA_START flag in the dma control register
- *
- * May be used as the bmdma_stop() entry in ata_port_operations.
- *
- * LOCKING:
- * spin_lock_irqsave(host_set lock)
- */
-
-void ata_bmdma_stop(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- if (ap->flags & ATA_FLAG_MMIO) {
- void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
-
- /* clear start/stop bit */
- writeb(readb(mmio + ATA_DMA_CMD) & ~ATA_DMA_START,
- mmio + ATA_DMA_CMD);
- } else {
- /* clear start/stop bit */
- outb(inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD) & ~ATA_DMA_START,
- ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
- }
-
- /* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */
- ata_altstatus(ap); /* dummy read */
-}
-
-/**
* ata_host_intr - Handle host interrupt for given (port, task)
* @ap: Port on which interrupt arrived (possibly...)
* @qc: Taskfile currently active in engine
@@ -4506,14 +4353,15 @@ int ata_device_resume(struct ata_port *a
* Flush the cache on the drive, if appropriate, then issue a
* standbynow command.
*/
-int ata_device_suspend(struct ata_port *ap, struct ata_device *dev)
+int ata_device_suspend(struct ata_port *ap, struct ata_device *dev, pm_message_t state)
{
if (!ata_dev_present(dev))
return 0;
if (dev->class == ATA_DEV_ATA)
ata_flush_cache(ap, dev);
- ata_standby_drive(ap, dev);
+ if (state.event != PM_EVENT_FREEZE)
+ ata_standby_drive(ap, dev);
ap->flags |= ATA_FLAG_SUSPENDED;
return 0;
}
@@ -4533,7 +4381,7 @@ int ata_device_suspend(struct ata_port *
int ata_port_start (struct ata_port *ap)
{
- struct device *dev = ap->host_set->dev;
+ struct device *dev = ap->dev;
int rc;
ap->prd = dma_alloc_coherent(dev, ATA_PRD_TBL_SZ, &ap->prd_dma, GFP_KERNEL);
@@ -4566,7 +4414,7 @@ int ata_port_start (struct ata_port *ap)
void ata_port_stop (struct ata_port *ap)
{
- struct device *dev = ap->host_set->dev;
+ struct device *dev = ap->dev;
dma_free_coherent(dev, ATA_PRD_TBL_SZ, ap->prd, ap->prd_dma);
ata_pad_free(ap, dev);
@@ -4632,6 +4480,7 @@ static void ata_host_init(struct ata_por
ap->host = host;
ap->ctl = ATA_DEVCTL_OBS;
ap->host_set = host_set;
+ ap->dev = ent->dev;
ap->port_no = port_no;
ap->hard_port_no =
ent->legacy_mode ? ent->hard_port_no : port_no;
@@ -4647,8 +4496,13 @@ static void ata_host_init(struct ata_por
INIT_WORK(&ap->port_task, NULL, NULL);
INIT_LIST_HEAD(&ap->eh_done_q);
- for (i = 0; i < ATA_MAX_DEVICES; i++)
- ap->device[i].devno = i;
+ for (i = 0; i < ATA_MAX_DEVICES; i++) {
+ struct ata_device *dev = &ap->device[i];
+ dev->devno = i;
+ dev->pio_mask = UINT_MAX;
+ dev->mwdma_mask = UINT_MAX;
+ dev->udma_mask = UINT_MAX;
+ }
#ifdef ATA_IRQ_TRAP
ap->stats.unhandled_irq = 1;
@@ -4842,7 +4696,7 @@ err_free_ret:
* ata_host_set_remove - PCI layer callback for device removal
* @host_set: ATA host set that was removed
*
- * Unregister all objects associated with this host set. Free those
+ * Unregister all objects associated with this host set. Free those
* objects.
*
* LOCKING:
@@ -5114,6 +4968,8 @@ EXPORT_SYMBOL_GPL(ata_std_postreset);
EXPORT_SYMBOL_GPL(ata_std_probe_reset);
EXPORT_SYMBOL_GPL(ata_drive_probe_reset);
EXPORT_SYMBOL_GPL(ata_dev_revalidate);
+EXPORT_SYMBOL_GPL(ata_dev_classify);
+EXPORT_SYMBOL_GPL(ata_dev_pair);
EXPORT_SYMBOL_GPL(ata_port_disable);
EXPORT_SYMBOL_GPL(ata_ratelimit);
EXPORT_SYMBOL_GPL(ata_busy_sleep);
@@ -5124,7 +4980,6 @@ EXPORT_SYMBOL_GPL(ata_scsi_error);
EXPORT_SYMBOL_GPL(ata_scsi_slave_config);
EXPORT_SYMBOL_GPL(ata_scsi_release);
EXPORT_SYMBOL_GPL(ata_host_intr);
-EXPORT_SYMBOL_GPL(ata_dev_classify);
EXPORT_SYMBOL_GPL(ata_id_string);
EXPORT_SYMBOL_GPL(ata_id_c_string);
EXPORT_SYMBOL_GPL(ata_scsi_simulate);
diff --git a/drivers/scsi/libata-scsi.c b/drivers/scsi/libata-scsi.c
index a1259b2..628191b 100644
--- a/drivers/scsi/libata-scsi.c
+++ b/drivers/scsi/libata-scsi.c
@@ -256,7 +256,7 @@ int ata_task_ioctl(struct scsi_device *s
scsi_cmd[14] = args[0];
/* Good values for timeout and retries? Values below
- from scsi_ioctl_send_command() for default case... */
+ from scsi_ioctl_send_command() for default case... */
if (scsi_execute_req(scsidev, scsi_cmd, DMA_NONE, NULL, 0, &sshdr,
(10*HZ), 5))
rc = -EIO;
@@ -267,20 +267,8 @@ int ata_task_ioctl(struct scsi_device *s
int ata_scsi_ioctl(struct scsi_device *scsidev, int cmd, void __user *arg)
{
- struct ata_port *ap;
- struct ata_device *dev;
int val = -EINVAL, rc = -EINVAL;
- ap = (struct ata_port *) &scsidev->host->hostdata[0];
- if (!ap)
- goto out;
-
- dev = ata_scsi_find_dev(ap, scsidev);
- if (!dev) {
- rc = -ENODEV;
- goto out;
- }
-
switch (cmd) {
case ATA_IOC_GET_IO32:
val = 0;
@@ -309,7 +297,6 @@ int ata_scsi_ioctl(struct scsi_device *s
break;
}
-out:
return rc;
}
@@ -414,12 +401,12 @@ int ata_scsi_device_resume(struct scsi_d
return ata_device_resume(ap, dev);
}
-int ata_scsi_device_suspend(struct scsi_device *sdev)
+int ata_scsi_device_suspend(struct scsi_device *sdev, pm_message_t state)
{
struct ata_port *ap = (struct ata_port *) &sdev->host->hostdata[0];
struct ata_device *dev = &ap->device[sdev->id];
- return ata_device_suspend(ap, dev);
+ return ata_device_suspend(ap, dev, state);
}
/**
@@ -438,7 +425,7 @@ int ata_scsi_device_suspend(struct scsi_
* LOCKING:
* spin_lock_irqsave(host_set lock)
*/
-void ata_to_sense_error(unsigned id, u8 drv_stat, u8 drv_err, u8 *sk, u8 *asc,
+void ata_to_sense_error(unsigned id, u8 drv_stat, u8 drv_err, u8 *sk, u8 *asc,
u8 *ascq)
{
int i;
@@ -495,7 +482,7 @@ void ata_to_sense_error(unsigned id, u8
/* Look for drv_err */
for (i = 0; sense_table[i][0] != 0xFF; i++) {
/* Look for best matches first */
- if ((sense_table[i][0] & drv_err) ==
+ if ((sense_table[i][0] & drv_err) ==
sense_table[i][0]) {
*sk = sense_table[i][1];
*asc = sense_table[i][2];
@@ -518,7 +505,7 @@ void ata_to_sense_error(unsigned id, u8
}
}
/* No error? Undecoded? */
- printk(KERN_WARNING "ata%u: no sense translation for status: 0x%02x\n",
+ printk(KERN_WARNING "ata%u: no sense translation for status: 0x%02x\n",
id, drv_stat);
/* We need a sensible error return here, which is tricky, and one
@@ -1150,14 +1137,14 @@ static unsigned int ata_scsi_verify_xlat
DPRINTK("block %u track %u cyl %u head %u sect %u\n",
(u32)block, track, cyl, head, sect);
-
- /* Check whether the converted CHS can fit.
- Cylinder: 0-65535
+
+ /* Check whether the converted CHS can fit.
+ Cylinder: 0-65535
Head: 0-15
Sector: 1-255*/
- if ((cyl >> 16) || (head >> 4) || (sect >> 8) || (!sect))
+ if ((cyl >> 16) || (head >> 4) || (sect >> 8) || (!sect))
goto out_of_range;
-
+
tf->command = ATA_CMD_VERIFY;
tf->nsect = n_block & 0xff; /* Sector count 0 means 256 sectors */
tf->lbal = sect;
@@ -1289,7 +1276,7 @@ static unsigned int ata_scsi_rw_xlat(str
tf->lbal = block & 0xff;
tf->device |= ATA_LBA;
- } else {
+ } else {
/* CHS */
u32 sect, head, cyl, track;
@@ -1309,8 +1296,8 @@ static unsigned int ata_scsi_rw_xlat(str
DPRINTK("block %u track %u cyl %u head %u sect %u\n",
(u32)block, track, cyl, head, sect);
- /* Check whether the converted CHS can fit.
- Cylinder: 0-65535
+ /* Check whether the converted CHS can fit.
+ Cylinder: 0-65535
Head: 0-15
Sector: 1-255*/
if ((cyl >> 16) || (head >> 4) || (sect >> 8) || (!sect))
@@ -1697,7 +1684,7 @@ unsigned int ata_scsiop_inq_83(struct at
if (buflen > (ATA_SERNO_LEN + num + 3)) {
/* piv=0, assoc=lu, code_set=ACSII, designator=vendor */
- rbuf[num + 0] = 2;
+ rbuf[num + 0] = 2;
rbuf[num + 3] = ATA_SERNO_LEN;
num += 4;
ata_id_string(args->id, (unsigned char *) rbuf + num,
@@ -1707,8 +1694,8 @@ unsigned int ata_scsiop_inq_83(struct at
if (buflen > (sat_model_serial_desc_len + num + 3)) {
/* SAT defined lu model and serial numbers descriptor */
/* piv=0, assoc=lu, code_set=ACSII, designator=t10 vendor id */
- rbuf[num + 0] = 2;
- rbuf[num + 1] = 1;
+ rbuf[num + 0] = 2;
+ rbuf[num + 1] = 1;
rbuf[num + 3] = sat_model_serial_desc_len;
num += 4;
memcpy(rbuf + num, "ATA ", 8);
@@ -2597,6 +2584,21 @@ static inline void ata_scsi_dump_cdb(str
#endif
}
+static inline void __ata_scsi_queuecmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *),
+ struct ata_port *ap, struct ata_device *dev)
+{
+ if (dev->class == ATA_DEV_ATA) {
+ ata_xlat_func_t xlat_func = ata_get_xlat_func(dev,
+ cmd->cmnd[0]);
+
+ if (xlat_func)
+ ata_scsi_translate(ap, dev, cmd, done, xlat_func);
+ else
+ ata_scsi_simulate(ap, dev, cmd, done);
+ } else
+ ata_scsi_translate(ap, dev, cmd, done, atapi_xlat);
+}
+
/**
* ata_scsi_queuecmd - Issue SCSI cdb to libata-managed device
* @cmd: SCSI command to be sent
@@ -2631,24 +2633,13 @@ int ata_scsi_queuecmd(struct scsi_cmnd *
ata_scsi_dump_cdb(ap, cmd);
dev = ata_scsi_find_dev(ap, scsidev);
- if (unlikely(!dev)) {
+ if (likely(dev))
+ __ata_scsi_queuecmd(cmd, done, ap, dev);
+ else {
cmd->result = (DID_BAD_TARGET << 16);
done(cmd);
- goto out_unlock;
}
- if (dev->class == ATA_DEV_ATA) {
- ata_xlat_func_t xlat_func = ata_get_xlat_func(dev,
- cmd->cmnd[0]);
-
- if (xlat_func)
- ata_scsi_translate(ap, dev, cmd, done, xlat_func);
- else
- ata_scsi_simulate(ap, dev, cmd, done);
- } else
- ata_scsi_translate(ap, dev, cmd, done, atapi_xlat);
-
-out_unlock:
spin_unlock(&ap->host_set->lock);
spin_lock(shost->host_lock);
return 0;
diff --git a/drivers/scsi/sata_nv.c b/drivers/scsi/sata_nv.c
index e5b20c6..f77bf18 100644
--- a/drivers/scsi/sata_nv.c
+++ b/drivers/scsi/sata_nv.c
@@ -29,34 +29,6 @@
* NV-specific details such as register offsets, SATA phy location,
* hotplug info, etc.
*
- * 0.10
- * - Fixed spurious interrupts issue seen with the Maxtor 6H500F0 500GB
- * drive. Also made the check_hotplug() callbacks return whether there
- * was a hotplug interrupt or not. This was not the source of the
- * spurious interrupts, but is the right thing to do anyway.
- *
- * 0.09
- * - Fixed bug introduced by 0.08's MCP51 and MCP55 support.
- *
- * 0.08
- * - Added support for MCP51 and MCP55.
- *
- * 0.07
- * - Added support for RAID class code.
- *
- * 0.06
- * - Added generic SATA support by using a pci_device_id that filters on
- * the IDE storage class code.
- *
- * 0.03
- * - Fixed a bug where the hotplug handlers for non-CK804/MCP04 were using
- * mmio_base, which is only set for the CK804/MCP04 case.
- *
- * 0.02
- * - Added support for CK804 SATA controller.
- *
- * 0.01
- * - Initial revision.
*/
#include <linux/config.h>
@@ -74,53 +46,55 @@
#define DRV_NAME "sata_nv"
#define DRV_VERSION "0.8"
-#define NV_PORTS 2
-#define NV_PIO_MASK 0x1f
-#define NV_MWDMA_MASK 0x07
-#define NV_UDMA_MASK 0x7f
-#define NV_PORT0_SCR_REG_OFFSET 0x00
-#define NV_PORT1_SCR_REG_OFFSET 0x40
-
-#define NV_INT_STATUS 0x10
-#define NV_INT_STATUS_CK804 0x440
-#define NV_INT_STATUS_PDEV_INT 0x01
-#define NV_INT_STATUS_PDEV_PM 0x02
-#define NV_INT_STATUS_PDEV_ADDED 0x04
-#define NV_INT_STATUS_PDEV_REMOVED 0x08
-#define NV_INT_STATUS_SDEV_INT 0x10
-#define NV_INT_STATUS_SDEV_PM 0x20
-#define NV_INT_STATUS_SDEV_ADDED 0x40
-#define NV_INT_STATUS_SDEV_REMOVED 0x80
-#define NV_INT_STATUS_PDEV_HOTPLUG (NV_INT_STATUS_PDEV_ADDED | \
- NV_INT_STATUS_PDEV_REMOVED)
-#define NV_INT_STATUS_SDEV_HOTPLUG (NV_INT_STATUS_SDEV_ADDED | \
- NV_INT_STATUS_SDEV_REMOVED)
-#define NV_INT_STATUS_HOTPLUG (NV_INT_STATUS_PDEV_HOTPLUG | \
- NV_INT_STATUS_SDEV_HOTPLUG)
-
-#define NV_INT_ENABLE 0x11
-#define NV_INT_ENABLE_CK804 0x441
-#define NV_INT_ENABLE_PDEV_MASK 0x01
-#define NV_INT_ENABLE_PDEV_PM 0x02
-#define NV_INT_ENABLE_PDEV_ADDED 0x04
-#define NV_INT_ENABLE_PDEV_REMOVED 0x08
-#define NV_INT_ENABLE_SDEV_MASK 0x10
-#define NV_INT_ENABLE_SDEV_PM 0x20
-#define NV_INT_ENABLE_SDEV_ADDED 0x40
-#define NV_INT_ENABLE_SDEV_REMOVED 0x80
-#define NV_INT_ENABLE_PDEV_HOTPLUG (NV_INT_ENABLE_PDEV_ADDED | \
- NV_INT_ENABLE_PDEV_REMOVED)
-#define NV_INT_ENABLE_SDEV_HOTPLUG (NV_INT_ENABLE_SDEV_ADDED | \
- NV_INT_ENABLE_SDEV_REMOVED)
-#define NV_INT_ENABLE_HOTPLUG (NV_INT_ENABLE_PDEV_HOTPLUG | \
- NV_INT_ENABLE_SDEV_HOTPLUG)
-
-#define NV_INT_CONFIG 0x12
-#define NV_INT_CONFIG_METHD 0x01 // 0 = INT, 1 = SMI
-
-// For PCI config register 20
-#define NV_MCP_SATA_CFG_20 0x50
-#define NV_MCP_SATA_CFG_20_SATA_SPACE_EN 0x04
+enum {
+ NV_PORTS = 2,
+ NV_PIO_MASK = 0x1f,
+ NV_MWDMA_MASK = 0x07,
+ NV_UDMA_MASK = 0x7f,
+ NV_PORT0_SCR_REG_OFFSET = 0x00,
+ NV_PORT1_SCR_REG_OFFSET = 0x40,
+
+ NV_INT_STATUS = 0x10,
+ NV_INT_STATUS_CK804 = 0x440,
+ NV_INT_STATUS_PDEV_INT = 0x01,
+ NV_INT_STATUS_PDEV_PM = 0x02,
+ NV_INT_STATUS_PDEV_ADDED = 0x04,
+ NV_INT_STATUS_PDEV_REMOVED = 0x08,
+ NV_INT_STATUS_SDEV_INT = 0x10,
+ NV_INT_STATUS_SDEV_PM = 0x20,
+ NV_INT_STATUS_SDEV_ADDED = 0x40,
+ NV_INT_STATUS_SDEV_REMOVED = 0x80,
+ NV_INT_STATUS_PDEV_HOTPLUG = (NV_INT_STATUS_PDEV_ADDED |
+ NV_INT_STATUS_PDEV_REMOVED),
+ NV_INT_STATUS_SDEV_HOTPLUG = (NV_INT_STATUS_SDEV_ADDED |
+ NV_INT_STATUS_SDEV_REMOVED),
+ NV_INT_STATUS_HOTPLUG = (NV_INT_STATUS_PDEV_HOTPLUG |
+ NV_INT_STATUS_SDEV_HOTPLUG),
+
+ NV_INT_ENABLE = 0x11,
+ NV_INT_ENABLE_CK804 = 0x441,
+ NV_INT_ENABLE_PDEV_MASK = 0x01,
+ NV_INT_ENABLE_PDEV_PM = 0x02,
+ NV_INT_ENABLE_PDEV_ADDED = 0x04,
+ NV_INT_ENABLE_PDEV_REMOVED = 0x08,
+ NV_INT_ENABLE_SDEV_MASK = 0x10,
+ NV_INT_ENABLE_SDEV_PM = 0x20,
+ NV_INT_ENABLE_SDEV_ADDED = 0x40,
+ NV_INT_ENABLE_SDEV_REMOVED = 0x80,
+ NV_INT_ENABLE_PDEV_HOTPLUG = (NV_INT_ENABLE_PDEV_ADDED |
+ NV_INT_ENABLE_PDEV_REMOVED),
+ NV_INT_ENABLE_SDEV_HOTPLUG = (NV_INT_ENABLE_SDEV_ADDED |
+ NV_INT_ENABLE_SDEV_REMOVED),
+ NV_INT_ENABLE_HOTPLUG = (NV_INT_ENABLE_PDEV_HOTPLUG |
+ NV_INT_ENABLE_SDEV_HOTPLUG),
+
+ NV_INT_CONFIG = 0x12,
+ NV_INT_CONFIG_METHD = 0x01, // 0 = INT, 1 = SMI
+
+ // For PCI config register 20
+ NV_MCP_SATA_CFG_20 = 0x50,
+ NV_MCP_SATA_CFG_20_SATA_SPACE_EN = 0x04,
+};
static int nv_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
static irqreturn_t nv_interrupt (int irq, void *dev_instance,
@@ -175,8 +149,6 @@ static const struct pci_device_id nv_pci
{ 0, } /* terminate list */
};
-#define NV_HOST_FLAGS_SCR_MMIO 0x00000001
-
struct nv_host_desc
{
enum nv_host_type host_type;
@@ -332,36 +304,23 @@ static irqreturn_t nv_interrupt (int irq
static u32 nv_scr_read (struct ata_port *ap, unsigned int sc_reg)
{
- struct ata_host_set *host_set = ap->host_set;
- struct nv_host *host = host_set->private_data;
-
if (sc_reg > SCR_CONTROL)
return 0xffffffffU;
- if (host->host_flags & NV_HOST_FLAGS_SCR_MMIO)
- return readl((void __iomem *)ap->ioaddr.scr_addr + (sc_reg * 4));
- else
- return inl(ap->ioaddr.scr_addr + (sc_reg * 4));
+ return ioread32((void __iomem *)ap->ioaddr.scr_addr + (sc_reg * 4));
}
static void nv_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
{
- struct ata_host_set *host_set = ap->host_set;
- struct nv_host *host = host_set->private_data;
-
if (sc_reg > SCR_CONTROL)
return;
- if (host->host_flags & NV_HOST_FLAGS_SCR_MMIO)
- writel(val, (void __iomem *)ap->ioaddr.scr_addr + (sc_reg * 4));
- else
- outl(val, ap->ioaddr.scr_addr + (sc_reg * 4));
+ iowrite32(val, (void __iomem *)ap->ioaddr.scr_addr + (sc_reg * 4));
}
static void nv_host_stop (struct ata_host_set *host_set)
{
struct nv_host *host = host_set->private_data;
- struct pci_dev *pdev = to_pci_dev(host_set->dev);
// Disable hotplug event interrupts.
if (host->host_desc->disable_hotplug)
@@ -369,8 +328,7 @@ static void nv_host_stop (struct ata_hos
kfree(host);
- if (host_set->mmio_base)
- pci_iounmap(pdev, host_set->mmio_base);
+ ata_pci_host_stop(host_set);
}
static int nv_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
@@ -382,6 +340,7 @@ static int nv_init_one (struct pci_dev *
int pci_dev_busy = 0;
int rc;
u32 bar;
+ unsigned long base;
// Make sure this is a SATA controller by counting the number of bars
// (NVIDIA SATA controllers will always have six bars). Otherwise,
@@ -426,31 +385,16 @@ static int nv_init_one (struct pci_dev *
probe_ent->private_data = host;
- if (pci_resource_flags(pdev, 5) & IORESOURCE_MEM)
- host->host_flags |= NV_HOST_FLAGS_SCR_MMIO;
-
- if (host->host_flags & NV_HOST_FLAGS_SCR_MMIO) {
- unsigned long base;
-
- probe_ent->mmio_base = pci_iomap(pdev, 5, 0);
- if (probe_ent->mmio_base == NULL) {
- rc = -EIO;
- goto err_out_free_host;
- }
+ probe_ent->mmio_base = pci_iomap(pdev, 5, 0);
+ if (!probe_ent->mmio_base) {
+ rc = -EIO;
+ goto err_out_free_host;
+ }
- base = (unsigned long)probe_ent->mmio_base;
+ base = (unsigned long)probe_ent->mmio_base;
- probe_ent->port[0].scr_addr =
- base + NV_PORT0_SCR_REG_OFFSET;
- probe_ent->port[1].scr_addr =
- base + NV_PORT1_SCR_REG_OFFSET;
- } else {
-
- probe_ent->port[0].scr_addr =
- pci_resource_start(pdev, 5) | NV_PORT0_SCR_REG_OFFSET;
- probe_ent->port[1].scr_addr =
- pci_resource_start(pdev, 5) | NV_PORT1_SCR_REG_OFFSET;
- }
+ probe_ent->port[0].scr_addr = base + NV_PORT0_SCR_REG_OFFSET;
+ probe_ent->port[1].scr_addr = base + NV_PORT1_SCR_REG_OFFSET;
pci_set_master(pdev);
@@ -467,8 +411,7 @@ static int nv_init_one (struct pci_dev *
return 0;
err_out_iounmap:
- if (host->host_flags & NV_HOST_FLAGS_SCR_MMIO)
- pci_iounmap(pdev, probe_ent->mmio_base);
+ pci_iounmap(pdev, probe_ent->mmio_base);
err_out_free_host:
kfree(host);
err_out_free_ent:
diff --git a/drivers/scsi/sata_sil.c b/drivers/scsi/sata_sil.c
index 3e75d67..18c296c 100644
--- a/drivers/scsi/sata_sil.c
+++ b/drivers/scsi/sata_sil.c
@@ -371,7 +371,7 @@ static void sil_dev_config(struct ata_po
if (quirks & SIL_QUIRK_UDMA5MAX) {
printk(KERN_INFO "ata%u(%u): applying Maxtor errata fix %s\n",
ap->id, dev->devno, model_num);
- ap->udma_mask &= ATA_UDMA5;
+ dev->udma_mask &= ATA_UDMA5;
return;
}
}
diff --git a/drivers/scsi/sata_sil24.c b/drivers/scsi/sata_sil24.c
index 5d01e5c..068c98a 100644
--- a/drivers/scsi/sata_sil24.c
+++ b/drivers/scsi/sata_sil24.c
@@ -342,7 +342,7 @@ static struct ata_port_info sil24_port_i
.udma_mask = 0x3f, /* udma0-5 */
.port_ops = &sil24_ops,
},
- /* sil_3132 */
+ /* sil_3132 */
{
.sht = &sil24_sht,
.host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
@@ -842,9 +842,10 @@ static void sil24_port_stop(struct ata_p
static void sil24_host_stop(struct ata_host_set *host_set)
{
struct sil24_host_priv *hpriv = host_set->private_data;
+ struct pci_dev *pdev = to_pci_dev(host_set->dev);
- iounmap(hpriv->host_base);
- iounmap(hpriv->port_base);
+ pci_iounmap(pdev, hpriv->host_base);
+ pci_iounmap(pdev, hpriv->port_base);
kfree(hpriv);
}
@@ -871,26 +872,23 @@ static int sil24_init_one(struct pci_dev
goto out_disable;
rc = -ENOMEM;
- /* ioremap mmio registers */
- host_base = ioremap(pci_resource_start(pdev, 0),
- pci_resource_len(pdev, 0));
+ /* map mmio registers */
+ host_base = pci_iomap(pdev, 0, 0);
if (!host_base)
goto out_free;
- port_base = ioremap(pci_resource_start(pdev, 2),
- pci_resource_len(pdev, 2));
+ port_base = pci_iomap(pdev, 2, 0);
if (!port_base)
goto out_free;
/* allocate & init probe_ent and hpriv */
- probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL);
+ probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL);
if (!probe_ent)
goto out_free;
- hpriv = kmalloc(sizeof(*hpriv), GFP_KERNEL);
+ hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL);
if (!hpriv)
goto out_free;
- memset(probe_ent, 0, sizeof(*probe_ent));
probe_ent->dev = pci_dev_to_dev(pdev);
INIT_LIST_HEAD(&probe_ent->node);
@@ -907,7 +905,6 @@ static int sil24_init_one(struct pci_dev
probe_ent->mmio_base = port_base;
probe_ent->private_data = hpriv;
- memset(hpriv, 0, sizeof(*hpriv));
hpriv->host_base = host_base;
hpriv->port_base = port_base;
@@ -1011,9 +1008,9 @@ static int sil24_init_one(struct pci_dev
out_free:
if (host_base)
- iounmap(host_base);
+ pci_iounmap(pdev, host_base);
if (port_base)
- iounmap(port_base);
+ pci_iounmap(pdev, port_base);
kfree(probe_ent);
kfree(hpriv);
pci_release_regions(pdev);
diff --git a/drivers/scsi/sata_uli.c b/drivers/scsi/sata_uli.c
index 8f50257..7ac5a5f 100644
--- a/drivers/scsi/sata_uli.c
+++ b/drivers/scsi/sata_uli.c
@@ -44,6 +44,8 @@ enum {
uli_5287 = 1,
uli_5281 = 2,
+ uli_max_ports = 4,
+
/* PCI configuration registers */
ULI5287_BASE = 0x90, /* sata0 phy SCR registers */
ULI5287_OFFS = 0x10, /* offset from sata0->sata1 phy regs */
@@ -51,6 +53,10 @@ enum {
ULI5281_OFFS = 0x60, /* offset from sata0->sata1 phy regs */
};
+struct uli_priv {
+ unsigned int scr_cfg_addr[uli_max_ports];
+};
+
static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg);
static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
@@ -137,7 +143,8 @@ MODULE_VERSION(DRV_VERSION);
static unsigned int get_scr_cfg_addr(struct ata_port *ap, unsigned int sc_reg)
{
- return ap->ioaddr.scr_addr + (4 * sc_reg);
+ struct uli_priv *hpriv = ap->host_set->private_data;
+ return hpriv->scr_cfg_addr[ap->port_no] + (4 * sc_reg);
}
static u32 uli_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
@@ -182,6 +189,7 @@ static int uli_init_one (struct pci_dev
int rc;
unsigned int board_idx = (unsigned int) ent->driver_data;
int pci_dev_busy = 0;
+ struct uli_priv *hpriv;
if (!printed_version++)
dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
@@ -210,10 +218,18 @@ static int uli_init_one (struct pci_dev
goto err_out_regions;
}
+ hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL);
+ if (!hpriv) {
+ rc = -ENOMEM;
+ goto err_out_probe_ent;
+ }
+
+ probe_ent->private_data = hpriv;
+
switch (board_idx) {
case uli_5287:
- probe_ent->port[0].scr_addr = ULI5287_BASE;
- probe_ent->port[1].scr_addr = ULI5287_BASE + ULI5287_OFFS;
+ hpriv->scr_cfg_addr[0] = ULI5287_BASE;
+ hpriv->scr_cfg_addr[1] = ULI5287_BASE + ULI5287_OFFS;
probe_ent->n_ports = 4;
probe_ent->port[2].cmd_addr = pci_resource_start(pdev, 0) + 8;
@@ -221,27 +237,27 @@ static int uli_init_one (struct pci_dev
probe_ent->port[2].ctl_addr =
(pci_resource_start(pdev, 1) | ATA_PCI_CTL_OFS) + 4;
probe_ent->port[2].bmdma_addr = pci_resource_start(pdev, 4) + 16;
- probe_ent->port[2].scr_addr = ULI5287_BASE + ULI5287_OFFS*4;
+ hpriv->scr_cfg_addr[2] = ULI5287_BASE + ULI5287_OFFS*4;
probe_ent->port[3].cmd_addr = pci_resource_start(pdev, 2) + 8;
probe_ent->port[3].altstatus_addr =
probe_ent->port[3].ctl_addr =
(pci_resource_start(pdev, 3) | ATA_PCI_CTL_OFS) + 4;
probe_ent->port[3].bmdma_addr = pci_resource_start(pdev, 4) + 24;
- probe_ent->port[3].scr_addr = ULI5287_BASE + ULI5287_OFFS*5;
+ hpriv->scr_cfg_addr[3] = ULI5287_BASE + ULI5287_OFFS*5;
ata_std_ports(&probe_ent->port[2]);
ata_std_ports(&probe_ent->port[3]);
break;
case uli_5289:
- probe_ent->port[0].scr_addr = ULI5287_BASE;
- probe_ent->port[1].scr_addr = ULI5287_BASE + ULI5287_OFFS;
+ hpriv->scr_cfg_addr[0] = ULI5287_BASE;
+ hpriv->scr_cfg_addr[1] = ULI5287_BASE + ULI5287_OFFS;
break;
case uli_5281:
- probe_ent->port[0].scr_addr = ULI5281_BASE;
- probe_ent->port[1].scr_addr = ULI5281_BASE + ULI5281_OFFS;
+ hpriv->scr_cfg_addr[0] = ULI5281_BASE;
+ hpriv->scr_cfg_addr[1] = ULI5281_BASE + ULI5281_OFFS;
break;
default:
@@ -258,9 +274,10 @@ static int uli_init_one (struct pci_dev
return 0;
+err_out_probe_ent:
+ kfree(probe_ent);
err_out_regions:
pci_release_regions(pdev);
-
err_out:
if (!pci_dev_busy)
pci_disable_device(pdev);
diff --git a/drivers/scsi/sata_vsc.c b/drivers/scsi/sata_vsc.c
index 9701a80..836bbbb 100644
--- a/drivers/scsi/sata_vsc.c
+++ b/drivers/scsi/sata_vsc.c
@@ -230,11 +230,11 @@ static irqreturn_t vsc_sata_interrupt (i
handled += ata_host_intr(ap, qc);
} else if (is_vsc_sata_int_err(i, int_status)) {
/*
- * On some chips (i.e. Intel 31244), an error
+ * On some chips (i.e. Intel 31244), an error
* interrupt will sneak in at initialization
* time (phy state changes). Clearing the SCR
* error register is not required, but it prevents
- * the phy state change interrupts from recurring
+ * the phy state change interrupts from recurring
* later.
*/
u32 err_status;
diff --git a/drivers/scsi/scsi_sysfs.c b/drivers/scsi/scsi_sysfs.c
index 8905549..a6fde52 100644
--- a/drivers/scsi/scsi_sysfs.c
+++ b/drivers/scsi/scsi_sysfs.c
@@ -286,7 +286,7 @@ static int scsi_bus_suspend(struct devic
return err;
if (sht->suspend)
- err = sht->suspend(sdev);
+ err = sht->suspend(sdev, state);
return err;
}
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 7a54244..0471922 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -358,6 +358,11 @@ struct ata_device {
unsigned int max_sectors; /* per-device max sectors */
unsigned int cdb_len;
+ /* per-dev xfer mask */
+ unsigned int pio_mask;
+ unsigned int mwdma_mask;
+ unsigned int udma_mask;
+
/* for CHS addressing */
u16 cylinders; /* Number of cylinders */
u16 heads; /* Number of heads */
@@ -395,6 +400,7 @@ struct ata_port {
struct ata_host_stats stats;
struct ata_host_set *host_set;
+ struct device *dev;
struct work_struct port_task;
@@ -515,9 +521,9 @@ extern void ata_eh_qc_retry(struct ata_q
extern int ata_scsi_release(struct Scsi_Host *host);
extern unsigned int ata_host_intr(struct ata_port *ap, struct ata_queued_cmd *qc);
extern int ata_scsi_device_resume(struct scsi_device *);
-extern int ata_scsi_device_suspend(struct scsi_device *);
+extern int ata_scsi_device_suspend(struct scsi_device *, pm_message_t state);
extern int ata_device_resume(struct ata_port *, struct ata_device *);
-extern int ata_device_suspend(struct ata_port *, struct ata_device *);
+extern int ata_device_suspend(struct ata_port *, struct ata_device *, pm_message_t state);
extern int ata_ratelimit(void);
extern unsigned int ata_busy_sleep(struct ata_port *ap,
unsigned long timeout_pat,
@@ -568,6 +574,8 @@ extern int ata_std_bios_param(struct scs
struct block_device *bdev,
sector_t capacity, int geom[]);
extern int ata_scsi_slave_config(struct scsi_device *sdev);
+extern struct ata_device *ata_dev_pair(struct ata_port *ap,
+ struct ata_device *adev);
/*
* Timing helpers
diff --git a/include/scsi/scsi_host.h b/include/scsi/scsi_host.h
index a6cf3e5..dc6862d 100644
--- a/include/scsi/scsi_host.h
+++ b/include/scsi/scsi_host.h
@@ -286,7 +286,7 @@ struct scsi_host_template {
* suspend support
*/
int (*resume)(struct scsi_device *);
- int (*suspend)(struct scsi_device *);
+ int (*suspend)(struct scsi_device *, pm_message_t state);
/*
* Name of proc directory
^ permalink raw reply related [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2006-03-23 1:15 Jeff Garzik
@ 2006-03-23 1:36 ` Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2006-03-23 1:36 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, linux-kernel
Jeff Garzik wrote:
> Please pull from 'upstream-linus' branch of
> master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git
In case it isn't obvious from the git history, this includes merging
with James B's SCSI pull (2152f8536668a957ea3214735b4761e7b22ef7d8) and
testing the result.
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2006-03-23 1:15 Jeff Garzik
2006-03-23 1:36 ` Jeff Garzik
0 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2006-03-23 1:15 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, linux-kernel
Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git
to receive the following updates:
drivers/scsi/Kconfig | 4 -
drivers/scsi/ahci.c | 135 +++++++++++++++++++++++++++++++++++++++++
drivers/scsi/libata-bmdma.c | 39 ++++++++++++
drivers/scsi/libata-core.c | 142 +++++++++++++++++++++++++++-----------------
drivers/scsi/libata-scsi.c | 138 ++++++++++++++++++++++++++----------------
drivers/scsi/pdc_adma.c | 2
drivers/scsi/sata_mv.c | 5 +
drivers/scsi/sata_svw.c | 54 ++++++++--------
drivers/scsi/sata_vsc.c | 122 ++++++++++++++++++++-----------------
include/linux/ata.h | 7 +-
include/linux/libata.h | 4 -
11 files changed, 459 insertions(+), 193 deletions(-)
Alan Cox:
libata: Add the useful macros/constants needed for merging PATA stuff
libata: pick a less confusion "um dunno" error
libata: make code actually compile with debugging on
libata: Note weakness in our PCI handling that one day wants fixing
libata: two new PCI helpers
libata: report which drive is causing mode problems
libata: make irqtrap mode compile
libata: note missing posting in mmio cmd write
libata: Fix a drive detection problem
Update libata DMA blacklist to cover versions, and resync with IDE layer
libata: Symbol exports
Albert Lee:
libata-dev: add flush task to ata_exec_internal()
libata-dev: Remove ATA_PROT_PIO_MULT
Brian King:
libata: Add some dummy noop functions
libata: ata_scsi_slave_config cleanup
Dan Williams:
[libata] sata_vsc: fix inconsistent NULL checking
Jeff Garzik:
[libata] SCSI VPD page 0x83 fixes
[libata] add prototypes for helpers
[libata] fix oops on non-DMA bmdma hardware
[libata sata_vsc, sata_svw] Convert #define'd constants to enums
Mark Lord:
[libata] sata_mv: off-by-1 fix
Tejun Heo:
libata: do not ignore PIO-only devices
ahci: add softreset
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index 5c94a5d..4035920 100644
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -595,10 +595,10 @@ config SCSI_SATA_VIA
If unsure, say N.
config SCSI_SATA_VITESSE
- tristate "VITESSE VSC-7174 SATA support"
+ tristate "VITESSE VSC-7174 / INTEL 31244 SATA support"
depends on SCSI_SATA && PCI
help
- This option enables support for Vitesse VSC7174 Serial ATA.
+ This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA.
If unsure, say N.
diff --git a/drivers/scsi/ahci.c b/drivers/scsi/ahci.c
index a1ddbba..ffba656 100644
--- a/drivers/scsi/ahci.c
+++ b/drivers/scsi/ahci.c
@@ -513,6 +513,138 @@ static void ahci_fill_cmd_slot(struct ah
pp->cmd_slot[0].tbl_addr_hi = cpu_to_le32((pp->cmd_tbl_dma >> 16) >> 16);
}
+static int ahci_poll_register(void __iomem *reg, u32 mask, u32 val,
+ unsigned long interval_msec,
+ unsigned long timeout_msec)
+{
+ unsigned long timeout;
+ u32 tmp;
+
+ timeout = jiffies + (timeout_msec * HZ) / 1000;
+ do {
+ tmp = readl(reg);
+ if ((tmp & mask) == val)
+ return 0;
+ msleep(interval_msec);
+ } while (time_before(jiffies, timeout));
+
+ return -1;
+}
+
+static int ahci_softreset(struct ata_port *ap, int verbose, unsigned int *class)
+{
+ struct ahci_host_priv *hpriv = ap->host_set->private_data;
+ struct ahci_port_priv *pp = ap->private_data;
+ void __iomem *mmio = ap->host_set->mmio_base;
+ void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+ const u32 cmd_fis_len = 5; /* five dwords */
+ const char *reason = NULL;
+ struct ata_taskfile tf;
+ u8 *fis;
+ int rc;
+
+ DPRINTK("ENTER\n");
+
+ /* prepare for SRST (AHCI-1.1 10.4.1) */
+ rc = ahci_stop_engine(ap);
+ if (rc) {
+ reason = "failed to stop engine";
+ goto fail_restart;
+ }
+
+ /* check BUSY/DRQ, perform Command List Override if necessary */
+ ahci_tf_read(ap, &tf);
+ if (tf.command & (ATA_BUSY | ATA_DRQ)) {
+ u32 tmp;
+
+ if (!(hpriv->cap & HOST_CAP_CLO)) {
+ rc = -EIO;
+ reason = "port busy but no CLO";
+ goto fail_restart;
+ }
+
+ tmp = readl(port_mmio + PORT_CMD);
+ tmp |= PORT_CMD_CLO;
+ writel(tmp, port_mmio + PORT_CMD);
+ readl(port_mmio + PORT_CMD); /* flush */
+
+ if (ahci_poll_register(port_mmio + PORT_CMD, PORT_CMD_CLO, 0x0,
+ 1, 500)) {
+ rc = -EIO;
+ reason = "CLO failed";
+ goto fail_restart;
+ }
+ }
+
+ /* restart engine */
+ ahci_start_engine(ap);
+
+ ata_tf_init(ap, &tf, 0);
+ fis = pp->cmd_tbl;
+
+ /* issue the first D2H Register FIS */
+ ahci_fill_cmd_slot(pp, cmd_fis_len | AHCI_CMD_RESET | AHCI_CMD_CLR_BUSY);
+
+ tf.ctl |= ATA_SRST;
+ ata_tf_to_fis(&tf, fis, 0);
+ fis[1] &= ~(1 << 7); /* turn off Command FIS bit */
+
+ writel(1, port_mmio + PORT_CMD_ISSUE);
+ readl(port_mmio + PORT_CMD_ISSUE); /* flush */
+
+ if (ahci_poll_register(port_mmio + PORT_CMD_ISSUE, 0x1, 0x0, 1, 500)) {
+ rc = -EIO;
+ reason = "1st FIS failed";
+ goto fail;
+ }
+
+ /* spec says at least 5us, but be generous and sleep for 1ms */
+ msleep(1);
+
+ /* issue the second D2H Register FIS */
+ ahci_fill_cmd_slot(pp, cmd_fis_len);
+
+ tf.ctl &= ~ATA_SRST;
+ ata_tf_to_fis(&tf, fis, 0);
+ fis[1] &= ~(1 << 7); /* turn off Command FIS bit */
+
+ writel(1, port_mmio + PORT_CMD_ISSUE);
+ readl(port_mmio + PORT_CMD_ISSUE); /* flush */
+
+ /* spec mandates ">= 2ms" before checking status.
+ * We wait 150ms, because that was the magic delay used for
+ * ATAPI devices in Hale Landis's ATADRVR, for the period of time
+ * between when the ATA command register is written, and then
+ * status is checked. Because waiting for "a while" before
+ * checking status is fine, post SRST, we perform this magic
+ * delay here as well.
+ */
+ msleep(150);
+
+ *class = ATA_DEV_NONE;
+ if (sata_dev_present(ap)) {
+ if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) {
+ rc = -EIO;
+ reason = "device not ready";
+ goto fail;
+ }
+ *class = ahci_dev_classify(ap);
+ }
+
+ DPRINTK("EXIT, class=%u\n", *class);
+ return 0;
+
+ fail_restart:
+ ahci_start_engine(ap);
+ fail:
+ if (verbose)
+ printk(KERN_ERR "ata%u: softreset failed (%s)\n",
+ ap->id, reason);
+ else
+ DPRINTK("EXIT, rc=%d reason=\"%s\"\n", rc, reason);
+ return rc;
+}
+
static int ahci_hardreset(struct ata_port *ap, int verbose, unsigned int *class)
{
int rc;
@@ -553,7 +685,8 @@ static void ahci_postreset(struct ata_po
static int ahci_probe_reset(struct ata_port *ap, unsigned int *classes)
{
- return ata_drive_probe_reset(ap, NULL, NULL, ahci_hardreset,
+ return ata_drive_probe_reset(ap, ata_std_probeinit,
+ ahci_softreset, ahci_hardreset,
ahci_postreset, classes);
}
diff --git a/drivers/scsi/libata-bmdma.c b/drivers/scsi/libata-bmdma.c
index a93336a..96b4d21 100644
--- a/drivers/scsi/libata-bmdma.c
+++ b/drivers/scsi/libata-bmdma.c
@@ -214,6 +214,8 @@ static void ata_exec_command_pio(struct
* Issues MMIO write to ATA command register, with proper
* synchronization with interrupt handler / other threads.
*
+ * FIXME: missing write posting for 400nS delay enforcement
+ *
* LOCKING:
* spin_lock_irqsave(host_set lock)
*/
@@ -648,6 +650,7 @@ int ata_pci_init_one (struct pci_dev *pd
goto err_out_regions;
}
+ /* FIXME: If we get no DMA mask we should fall back to PIO */
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
goto err_out_regions;
@@ -699,5 +702,41 @@ err_out:
return rc;
}
+/**
+ * ata_pci_clear_simplex - attempt to kick device out of simplex
+ * @pdev: PCI device
+ *
+ * Some PCI ATA devices report simplex mode but in fact can be told to
+ * enter non simplex mode. This implements the neccessary logic to
+ * perform the task on such devices. Calling it on other devices will
+ * have -undefined- behaviour.
+ */
+
+int ata_pci_clear_simplex(struct pci_dev *pdev)
+{
+ unsigned long bmdma = pci_resource_start(pdev, 4);
+ u8 simplex;
+
+ if (bmdma == 0)
+ return -ENOENT;
+
+ simplex = inb(bmdma + 0x02);
+ outb(simplex & 0x60, bmdma + 0x02);
+ simplex = inb(bmdma + 0x02);
+ if (simplex & 0x80)
+ return -EOPNOTSUPP;
+ return 0;
+}
+
+unsigned long ata_pci_default_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long xfer_mask)
+{
+ /* Filter out DMA modes if the device has been configured by
+ the BIOS as PIO only */
+
+ if (ap->ioaddr.bmdma_addr == 0)
+ xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
+ return xfer_mask;
+}
+
#endif /* CONFIG_PCI */
diff --git a/drivers/scsi/libata-core.c b/drivers/scsi/libata-core.c
index 64dce00..0314abd 100644
--- a/drivers/scsi/libata-core.c
+++ b/drivers/scsi/libata-core.c
@@ -962,6 +962,8 @@ ata_exec_internal(struct ata_port *ap, s
spin_unlock_irqrestore(&ap->host_set->lock, flags);
if (!wait_for_completion_timeout(&wait, ATA_TMOUT_INTERNAL)) {
+ ata_port_flush_task(ap);
+
spin_lock_irqsave(&ap->host_set->lock, flags);
/* We're racing with irq here. If we lose, the
@@ -1219,13 +1221,6 @@ static int ata_dev_configure(struct ata_
* common ATA, ATAPI feature tests
*/
- /* we require DMA support (bits 8 of word 49) */
- if (!ata_id_has_dma(id)) {
- printk(KERN_DEBUG "ata%u: no dma\n", ap->id);
- rc = -EINVAL;
- goto err_out_nosup;
- }
-
/* find max transfer mode; for printk only */
xfer_mask = ata_id_xfermask(id);
@@ -1737,7 +1732,7 @@ static int ata_host_set_pio(struct ata_p
continue;
if (!dev->pio_mode) {
- printk(KERN_WARNING "ata%u: no PIO support\n", ap->id);
+ printk(KERN_WARNING "ata%u: no PIO support for device %d.\n", ap->id, i);
return -1;
}
@@ -1999,9 +1994,19 @@ static unsigned int ata_bus_softreset(st
* status is checked. Because waiting for "a while" before
* checking status is fine, post SRST, we perform this magic
* delay here as well.
+ *
+ * Old drivers/ide uses the 2mS rule and then waits for ready
*/
msleep(150);
+
+ /* Before we perform post reset processing we want to see if
+ the bus shows 0xFF because the odd clown forgets the D7 pulldown
+ resistor */
+
+ if (ata_check_status(ap) == 0xFF)
+ return 1; /* Positive is failure for some reason */
+
ata_bus_post_reset(ap, devmask);
return 0;
@@ -2551,48 +2556,72 @@ int ata_dev_revalidate(struct ata_port *
}
static const char * const ata_dma_blacklist [] = {
- "WDC AC11000H",
- "WDC AC22100H",
- "WDC AC32500H",
- "WDC AC33100H",
- "WDC AC31600H",
- "WDC AC32100H",
- "WDC AC23200L",
- "Compaq CRD-8241B",
- "CRD-8400B",
- "CRD-8480B",
- "CRD-8482B",
- "CRD-84",
- "SanDisk SDP3B",
- "SanDisk SDP3B-64",
- "SANYO CD-ROM CRD",
- "HITACHI CDR-8",
- "HITACHI CDR-8335",
- "HITACHI CDR-8435",
- "Toshiba CD-ROM XM-6202B",
- "TOSHIBA CD-ROM XM-1702BC",
- "CD-532E-A",
- "E-IDE CD-ROM CR-840",
- "CD-ROM Drive/F5A",
- "WPI CDD-820",
- "SAMSUNG CD-ROM SC-148C",
- "SAMSUNG CD-ROM SC",
- "SanDisk SDP3B-64",
- "ATAPI CD-ROM DRIVE 40X MAXIMUM",
- "_NEC DV5800A",
+ "WDC AC11000H", NULL,
+ "WDC AC22100H", NULL,
+ "WDC AC32500H", NULL,
+ "WDC AC33100H", NULL,
+ "WDC AC31600H", NULL,
+ "WDC AC32100H", "24.09P07",
+ "WDC AC23200L", "21.10N21",
+ "Compaq CRD-8241B", NULL,
+ "CRD-8400B", NULL,
+ "CRD-8480B", NULL,
+ "CRD-8482B", NULL,
+ "CRD-84", NULL,
+ "SanDisk SDP3B", NULL,
+ "SanDisk SDP3B-64", NULL,
+ "SANYO CD-ROM CRD", NULL,
+ "HITACHI CDR-8", NULL,
+ "HITACHI CDR-8335", NULL,
+ "HITACHI CDR-8435", NULL,
+ "Toshiba CD-ROM XM-6202B", NULL,
+ "TOSHIBA CD-ROM XM-1702BC", NULL,
+ "CD-532E-A", NULL,
+ "E-IDE CD-ROM CR-840", NULL,
+ "CD-ROM Drive/F5A", NULL,
+ "WPI CDD-820", NULL,
+ "SAMSUNG CD-ROM SC-148C", NULL,
+ "SAMSUNG CD-ROM SC", NULL,
+ "SanDisk SDP3B-64", NULL,
+ "ATAPI CD-ROM DRIVE 40X MAXIMUM",NULL,
+ "_NEC DV5800A", NULL,
+ "SAMSUNG CD-ROM SN-124", "N001"
};
+
+static int ata_strim(char *s, size_t len)
+{
+ len = strnlen(s, len);
+
+ /* ATAPI specifies that empty space is blank-filled; remove blanks */
+ while ((len > 0) && (s[len - 1] == ' ')) {
+ len--;
+ s[len] = 0;
+ }
+ return len;
+}
static int ata_dma_blacklisted(const struct ata_device *dev)
{
- unsigned char model_num[41];
+ unsigned char model_num[40];
+ unsigned char model_rev[16];
+ unsigned int nlen, rlen;
int i;
- ata_id_c_string(dev->id, model_num, ATA_ID_PROD_OFS, sizeof(model_num));
-
- for (i = 0; i < ARRAY_SIZE(ata_dma_blacklist); i++)
- if (!strcmp(ata_dma_blacklist[i], model_num))
- return 1;
-
+ ata_id_string(dev->id, model_num, ATA_ID_PROD_OFS,
+ sizeof(model_num));
+ ata_id_string(dev->id, model_rev, ATA_ID_FW_REV_OFS,
+ sizeof(model_rev));
+ nlen = ata_strim(model_num, sizeof(model_num));
+ rlen = ata_strim(model_rev, sizeof(model_rev));
+
+ for (i = 0; i < ARRAY_SIZE(ata_dma_blacklist); i += 2) {
+ if (!strncmp(ata_dma_blacklist[i], model_num, nlen)) {
+ if (ata_dma_blacklist[i+1] == NULL)
+ return 1;
+ if (!strncmp(ata_dma_blacklist[i], model_rev, rlen))
+ return 1;
+ }
+ }
return 0;
}
@@ -2863,6 +2892,8 @@ void ata_qc_prep(struct ata_queued_cmd *
ata_fill_sg(qc);
}
+void ata_noop_qc_prep(struct ata_queued_cmd *qc) { }
+
/**
* ata_sg_init_one - Associate command with memory buffer
* @qc: Command to be associated
@@ -3907,7 +3938,6 @@ static inline int ata_should_dma_map(str
case ATA_PROT_ATAPI:
case ATA_PROT_PIO:
- case ATA_PROT_PIO_MULT:
if (ap->flags & ATA_FLAG_PIO_DMA)
return 1;
@@ -4199,14 +4229,17 @@ void ata_bmdma_setup(struct ata_queued_c
void ata_bmdma_irq_clear(struct ata_port *ap)
{
- if (ap->flags & ATA_FLAG_MMIO) {
- void __iomem *mmio = ((void __iomem *) ap->ioaddr.bmdma_addr) + ATA_DMA_STATUS;
- writeb(readb(mmio), mmio);
- } else {
- unsigned long addr = ap->ioaddr.bmdma_addr + ATA_DMA_STATUS;
- outb(inb(addr), addr);
- }
+ if (!ap->ioaddr.bmdma_addr)
+ return;
+ if (ap->flags & ATA_FLAG_MMIO) {
+ void __iomem *mmio =
+ ((void __iomem *) ap->ioaddr.bmdma_addr) + ATA_DMA_STATUS;
+ writeb(readb(mmio), mmio);
+ } else {
+ unsigned long addr = ap->ioaddr.bmdma_addr + ATA_DMA_STATUS;
+ outb(inb(addr), addr);
+ }
}
@@ -4337,9 +4370,9 @@ idle_irq:
#ifdef ATA_IRQ_TRAP
if ((ap->stats.idle_irq % 1000) == 0) {
- handled = 1;
ata_irq_ack(ap, 0); /* debug trap */
printk(KERN_WARNING "ata%d: irq trap\n", ap->id);
+ return 1;
}
#endif
return 0; /* irq not handled */
@@ -5064,6 +5097,7 @@ EXPORT_SYMBOL_GPL(ata_port_stop);
EXPORT_SYMBOL_GPL(ata_host_stop);
EXPORT_SYMBOL_GPL(ata_interrupt);
EXPORT_SYMBOL_GPL(ata_qc_prep);
+EXPORT_SYMBOL_GPL(ata_noop_qc_prep);
EXPORT_SYMBOL_GPL(ata_bmdma_setup);
EXPORT_SYMBOL_GPL(ata_bmdma_start);
EXPORT_SYMBOL_GPL(ata_bmdma_irq_clear);
@@ -5109,6 +5143,8 @@ EXPORT_SYMBOL_GPL(ata_pci_init_one);
EXPORT_SYMBOL_GPL(ata_pci_remove_one);
EXPORT_SYMBOL_GPL(ata_pci_device_suspend);
EXPORT_SYMBOL_GPL(ata_pci_device_resume);
+EXPORT_SYMBOL_GPL(ata_pci_default_filter);
+EXPORT_SYMBOL_GPL(ata_pci_clear_simplex);
#endif /* CONFIG_PCI */
EXPORT_SYMBOL_GPL(ata_device_suspend);
diff --git a/drivers/scsi/libata-scsi.c b/drivers/scsi/libata-scsi.c
index bd9f217..a1259b2 100644
--- a/drivers/scsi/libata-scsi.c
+++ b/drivers/scsi/libata-scsi.c
@@ -521,13 +521,11 @@ void ata_to_sense_error(unsigned id, u8
printk(KERN_WARNING "ata%u: no sense translation for status: 0x%02x\n",
id, drv_stat);
- /* For our last chance pick, use medium read error because
- * it's much more common than an ATA drive telling you a write
- * has failed.
- */
- *sk = MEDIUM_ERROR;
- *asc = 0x11; /* "unrecovered read error" */
- *ascq = 0x04; /* "auto-reallocation failed" */
+ /* We need a sensible error return here, which is tricky, and one
+ that won't cause people to do things like return a disk wrongly */
+ *sk = ABORTED_COMMAND;
+ *asc = 0x00;
+ *ascq = 0x00;
translate_done:
printk(KERN_ERR "ata%u: translated ATA stat/err 0x%02x/%02x to "
@@ -672,6 +670,41 @@ void ata_gen_fixed_sense(struct ata_queu
}
}
+static void ata_scsi_sdev_config(struct scsi_device *sdev)
+{
+ sdev->use_10_for_rw = 1;
+ sdev->use_10_for_ms = 1;
+}
+
+static void ata_scsi_dev_config(struct scsi_device *sdev,
+ struct ata_device *dev)
+{
+ unsigned int max_sectors;
+
+ /* TODO: 2048 is an arbitrary number, not the
+ * hardware maximum. This should be increased to
+ * 65534 when Jens Axboe's patch for dynamically
+ * determining max_sectors is merged.
+ */
+ max_sectors = ATA_MAX_SECTORS;
+ if (dev->flags & ATA_DFLAG_LBA48)
+ max_sectors = 2048;
+ if (dev->max_sectors)
+ max_sectors = dev->max_sectors;
+
+ blk_queue_max_sectors(sdev->request_queue, max_sectors);
+
+ /*
+ * SATA DMA transfers must be multiples of 4 byte, so
+ * we need to pad ATAPI transfers using an extra sg.
+ * Decrement max hw segments accordingly.
+ */
+ if (dev->class == ATA_DEV_ATAPI) {
+ request_queue_t *q = sdev->request_queue;
+ blk_queue_max_hw_segments(q, q->max_hw_segments - 1);
+ }
+}
+
/**
* ata_scsi_slave_config - Set SCSI device attributes
* @sdev: SCSI device to examine
@@ -686,41 +719,18 @@ void ata_gen_fixed_sense(struct ata_queu
int ata_scsi_slave_config(struct scsi_device *sdev)
{
- sdev->use_10_for_rw = 1;
- sdev->use_10_for_ms = 1;
+ ata_scsi_sdev_config(sdev);
blk_queue_max_phys_segments(sdev->request_queue, LIBATA_MAX_PRD);
if (sdev->id < ATA_MAX_DEVICES) {
struct ata_port *ap;
struct ata_device *dev;
- unsigned int max_sectors;
ap = (struct ata_port *) &sdev->host->hostdata[0];
dev = &ap->device[sdev->id];
- /* TODO: 2048 is an arbitrary number, not the
- * hardware maximum. This should be increased to
- * 65534 when Jens Axboe's patch for dynamically
- * determining max_sectors is merged.
- */
- max_sectors = ATA_MAX_SECTORS;
- if (dev->flags & ATA_DFLAG_LBA48)
- max_sectors = 2048;
- if (dev->max_sectors)
- max_sectors = dev->max_sectors;
-
- blk_queue_max_sectors(sdev->request_queue, max_sectors);
-
- /*
- * SATA DMA transfers must be multiples of 4 byte, so
- * we need to pad ATAPI transfers using an extra sg.
- * Decrement max hw segments accordingly.
- */
- if (dev->class == ATA_DEV_ATAPI) {
- request_queue_t *q = sdev->request_queue;
- blk_queue_max_hw_segments(q, q->max_hw_segments - 1);
- }
+ ata_scsi_dev_config(sdev, dev);
}
return 0; /* scsi layer doesn't check return value, sigh */
@@ -1552,7 +1562,7 @@ void ata_scsi_rbuf_fill(struct ata_scsi_
* @buflen: Response buffer length.
*
* Returns standard device identification data associated
- * with non-EVPD INQUIRY command output.
+ * with non-VPD INQUIRY command output.
*
* LOCKING:
* spin_lock_irqsave(host_set lock)
@@ -1603,12 +1613,12 @@ unsigned int ata_scsiop_inq_std(struct a
}
/**
- * ata_scsiop_inq_00 - Simulate INQUIRY EVPD page 0, list of pages
+ * ata_scsiop_inq_00 - Simulate INQUIRY VPD page 0, list of pages
* @args: device IDENTIFY data / SCSI command of interest.
* @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
* @buflen: Response buffer length.
*
- * Returns list of inquiry EVPD pages available.
+ * Returns list of inquiry VPD pages available.
*
* LOCKING:
* spin_lock_irqsave(host_set lock)
@@ -1622,7 +1632,7 @@ unsigned int ata_scsiop_inq_00(struct at
0x80, /* page 0x80, unit serial no page */
0x83 /* page 0x83, device ident page */
};
- rbuf[3] = sizeof(pages); /* number of supported EVPD pages */
+ rbuf[3] = sizeof(pages); /* number of supported VPD pages */
if (buflen > 6)
memcpy(rbuf + 4, pages, sizeof(pages));
@@ -1631,7 +1641,7 @@ unsigned int ata_scsiop_inq_00(struct at
}
/**
- * ata_scsiop_inq_80 - Simulate INQUIRY EVPD page 80, device serial number
+ * ata_scsiop_inq_80 - Simulate INQUIRY VPD page 80, device serial number
* @args: device IDENTIFY data / SCSI command of interest.
* @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
* @buflen: Response buffer length.
@@ -1660,16 +1670,16 @@ unsigned int ata_scsiop_inq_80(struct at
return 0;
}
-static const char * const inq_83_str = "Linux ATA-SCSI simulator";
-
/**
- * ata_scsiop_inq_83 - Simulate INQUIRY EVPD page 83, device identity
+ * ata_scsiop_inq_83 - Simulate INQUIRY VPD page 83, device identity
* @args: device IDENTIFY data / SCSI command of interest.
* @rbuf: Response buffer, to which simulated SCSI cmd output is sent.
* @buflen: Response buffer length.
*
- * Returns device identification. Currently hardcoded to
- * return "Linux ATA-SCSI simulator".
+ * Yields two logical unit device identification designators:
+ * - vendor specific ASCII containing the ATA serial number
+ * - SAT defined "t10 vendor id based" containing ASCII vendor
+ * name ("ATA "), model and serial numbers.
*
* LOCKING:
* spin_lock_irqsave(host_set lock)
@@ -1678,16 +1688,39 @@ static const char * const inq_83_str = "
unsigned int ata_scsiop_inq_83(struct ata_scsi_args *args, u8 *rbuf,
unsigned int buflen)
{
+ int num;
+ const int sat_model_serial_desc_len = 68;
+ const int ata_model_byte_len = 40;
+
rbuf[1] = 0x83; /* this page code */
- rbuf[3] = 4 + strlen(inq_83_str); /* page len */
+ num = 4;
- /* our one and only identification descriptor (vendor-specific) */
- if (buflen > (strlen(inq_83_str) + 4 + 4 - 1)) {
- rbuf[4 + 0] = 2; /* code set: ASCII */
- rbuf[4 + 3] = strlen(inq_83_str);
- memcpy(rbuf + 4 + 4, inq_83_str, strlen(inq_83_str));
+ if (buflen > (ATA_SERNO_LEN + num + 3)) {
+ /* piv=0, assoc=lu, code_set=ACSII, designator=vendor */
+ rbuf[num + 0] = 2;
+ rbuf[num + 3] = ATA_SERNO_LEN;
+ num += 4;
+ ata_id_string(args->id, (unsigned char *) rbuf + num,
+ ATA_ID_SERNO_OFS, ATA_SERNO_LEN);
+ num += ATA_SERNO_LEN;
}
-
+ if (buflen > (sat_model_serial_desc_len + num + 3)) {
+ /* SAT defined lu model and serial numbers descriptor */
+ /* piv=0, assoc=lu, code_set=ACSII, designator=t10 vendor id */
+ rbuf[num + 0] = 2;
+ rbuf[num + 1] = 1;
+ rbuf[num + 3] = sat_model_serial_desc_len;
+ num += 4;
+ memcpy(rbuf + num, "ATA ", 8);
+ num += 8;
+ ata_id_string(args->id, (unsigned char *) rbuf + num,
+ ATA_ID_PROD_OFS, ata_model_byte_len);
+ num += ata_model_byte_len;
+ ata_id_string(args->id, (unsigned char *) rbuf + num,
+ ATA_ID_SERNO_OFS, ATA_SERNO_LEN);
+ num += ATA_SERNO_LEN;
+ }
+ rbuf[3] = num - 4; /* page len (assume less than 256 bytes) */
return 0;
}
@@ -2366,9 +2399,6 @@ ata_scsi_map_proto(u8 byte1)
case 4: /* PIO Data-in */
case 5: /* PIO Data-out */
- if (byte1 & 0xe0) {
- return ATA_PROT_PIO_MULT;
- }
return ATA_PROT_PIO;
case 10: /* Device Reset */
@@ -2407,6 +2437,10 @@ ata_scsi_pass_thru(struct ata_queued_cmd
if ((tf->protocol = ata_scsi_map_proto(scsicmd[1])) == ATA_PROT_UNKNOWN)
goto invalid_fld;
+ if (scsicmd[1] & 0xe0)
+ /* PIO multi not supported yet */
+ goto invalid_fld;
+
/*
* 12 and 16 byte CDBs use different offsets to
* provide the various register values.
diff --git a/drivers/scsi/pdc_adma.c b/drivers/scsi/pdc_adma.c
index b3dc5f8..3c85c4b 100644
--- a/drivers/scsi/pdc_adma.c
+++ b/drivers/scsi/pdc_adma.c
@@ -321,7 +321,7 @@ static int adma_fill_sg(struct ata_queue
= (pFLAGS & pEND) ? 0 : cpu_to_le32(pp->pkt_dma + i + 4);
i += 4;
- VPRINTK("PRD[%u] = (0x%lX, 0x%X)\n", nelem,
+ VPRINTK("PRD[%u] = (0x%lX, 0x%X)\n", i/4,
(unsigned long)addr, len);
}
return i;
diff --git a/drivers/scsi/sata_mv.c b/drivers/scsi/sata_mv.c
index 874c5be..275ed9b 100644
--- a/drivers/scsi/sata_mv.c
+++ b/drivers/scsi/sata_mv.c
@@ -1262,6 +1262,7 @@ static u8 mv_get_crpb_status(struct ata_
void __iomem *port_mmio = mv_ap_base(ap);
struct mv_port_priv *pp = ap->private_data;
u32 out_ptr;
+ u8 ata_status;
out_ptr = readl(port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
@@ -1269,6 +1270,8 @@ static u8 mv_get_crpb_status(struct ata_
WARN_ON(((out_ptr >> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) !=
pp->rsp_consumer);
+ ata_status = pp->crpb[pp->rsp_consumer].flags >> CRPB_FLAG_STATUS_SHIFT;
+
/* increment our consumer index... */
pp->rsp_consumer = mv_inc_q_index(&pp->rsp_consumer);
@@ -1283,7 +1286,7 @@ static u8 mv_get_crpb_status(struct ata_
writelfl(out_ptr, port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
/* Return ATA status register for completed CRPB */
- return (pp->crpb[pp->rsp_consumer].flags >> CRPB_FLAG_STATUS_SHIFT);
+ return ata_status;
}
/**
diff --git a/drivers/scsi/sata_svw.c b/drivers/scsi/sata_svw.c
index 051e47d..724f0ed 100644
--- a/drivers/scsi/sata_svw.c
+++ b/drivers/scsi/sata_svw.c
@@ -56,33 +56,35 @@
#define DRV_NAME "sata_svw"
#define DRV_VERSION "1.07"
-/* Taskfile registers offsets */
-#define K2_SATA_TF_CMD_OFFSET 0x00
-#define K2_SATA_TF_DATA_OFFSET 0x00
-#define K2_SATA_TF_ERROR_OFFSET 0x04
-#define K2_SATA_TF_NSECT_OFFSET 0x08
-#define K2_SATA_TF_LBAL_OFFSET 0x0c
-#define K2_SATA_TF_LBAM_OFFSET 0x10
-#define K2_SATA_TF_LBAH_OFFSET 0x14
-#define K2_SATA_TF_DEVICE_OFFSET 0x18
-#define K2_SATA_TF_CMDSTAT_OFFSET 0x1c
-#define K2_SATA_TF_CTL_OFFSET 0x20
-
-/* DMA base */
-#define K2_SATA_DMA_CMD_OFFSET 0x30
-
-/* SCRs base */
-#define K2_SATA_SCR_STATUS_OFFSET 0x40
-#define K2_SATA_SCR_ERROR_OFFSET 0x44
-#define K2_SATA_SCR_CONTROL_OFFSET 0x48
-
-/* Others */
-#define K2_SATA_SICR1_OFFSET 0x80
-#define K2_SATA_SICR2_OFFSET 0x84
-#define K2_SATA_SIM_OFFSET 0x88
+enum {
+ /* Taskfile registers offsets */
+ K2_SATA_TF_CMD_OFFSET = 0x00,
+ K2_SATA_TF_DATA_OFFSET = 0x00,
+ K2_SATA_TF_ERROR_OFFSET = 0x04,
+ K2_SATA_TF_NSECT_OFFSET = 0x08,
+ K2_SATA_TF_LBAL_OFFSET = 0x0c,
+ K2_SATA_TF_LBAM_OFFSET = 0x10,
+ K2_SATA_TF_LBAH_OFFSET = 0x14,
+ K2_SATA_TF_DEVICE_OFFSET = 0x18,
+ K2_SATA_TF_CMDSTAT_OFFSET = 0x1c,
+ K2_SATA_TF_CTL_OFFSET = 0x20,
+
+ /* DMA base */
+ K2_SATA_DMA_CMD_OFFSET = 0x30,
+
+ /* SCRs base */
+ K2_SATA_SCR_STATUS_OFFSET = 0x40,
+ K2_SATA_SCR_ERROR_OFFSET = 0x44,
+ K2_SATA_SCR_CONTROL_OFFSET = 0x48,
+
+ /* Others */
+ K2_SATA_SICR1_OFFSET = 0x80,
+ K2_SATA_SICR2_OFFSET = 0x84,
+ K2_SATA_SIM_OFFSET = 0x88,
-/* Port stride */
-#define K2_SATA_PORT_OFFSET 0x100
+ /* Port stride */
+ K2_SATA_PORT_OFFSET = 0x100,
+};
static u8 k2_stat_check_status(struct ata_port *ap);
diff --git a/drivers/scsi/sata_vsc.c b/drivers/scsi/sata_vsc.c
index ee75b9b..9701a80 100644
--- a/drivers/scsi/sata_vsc.c
+++ b/drivers/scsi/sata_vsc.c
@@ -47,52 +47,58 @@
#include <linux/libata.h>
#define DRV_NAME "sata_vsc"
-#define DRV_VERSION "1.1"
+#define DRV_VERSION "1.2"
+
+enum {
+ /* Interrupt register offsets (from chip base address) */
+ VSC_SATA_INT_STAT_OFFSET = 0x00,
+ VSC_SATA_INT_MASK_OFFSET = 0x04,
+
+ /* Taskfile registers offsets */
+ VSC_SATA_TF_CMD_OFFSET = 0x00,
+ VSC_SATA_TF_DATA_OFFSET = 0x00,
+ VSC_SATA_TF_ERROR_OFFSET = 0x04,
+ VSC_SATA_TF_FEATURE_OFFSET = 0x06,
+ VSC_SATA_TF_NSECT_OFFSET = 0x08,
+ VSC_SATA_TF_LBAL_OFFSET = 0x0c,
+ VSC_SATA_TF_LBAM_OFFSET = 0x10,
+ VSC_SATA_TF_LBAH_OFFSET = 0x14,
+ VSC_SATA_TF_DEVICE_OFFSET = 0x18,
+ VSC_SATA_TF_STATUS_OFFSET = 0x1c,
+ VSC_SATA_TF_COMMAND_OFFSET = 0x1d,
+ VSC_SATA_TF_ALTSTATUS_OFFSET = 0x28,
+ VSC_SATA_TF_CTL_OFFSET = 0x29,
+
+ /* DMA base */
+ VSC_SATA_UP_DESCRIPTOR_OFFSET = 0x64,
+ VSC_SATA_UP_DATA_BUFFER_OFFSET = 0x6C,
+ VSC_SATA_DMA_CMD_OFFSET = 0x70,
+
+ /* SCRs base */
+ VSC_SATA_SCR_STATUS_OFFSET = 0x100,
+ VSC_SATA_SCR_ERROR_OFFSET = 0x104,
+ VSC_SATA_SCR_CONTROL_OFFSET = 0x108,
+
+ /* Port stride */
+ VSC_SATA_PORT_OFFSET = 0x200,
+
+ /* Error interrupt status bit offsets */
+ VSC_SATA_INT_ERROR_CRC = 0x40,
+ VSC_SATA_INT_ERROR_T = 0x20,
+ VSC_SATA_INT_ERROR_P = 0x10,
+ VSC_SATA_INT_ERROR_R = 0x8,
+ VSC_SATA_INT_ERROR_E = 0x4,
+ VSC_SATA_INT_ERROR_M = 0x2,
+ VSC_SATA_INT_PHY_CHANGE = 0x1,
+ VSC_SATA_INT_ERROR = (VSC_SATA_INT_ERROR_CRC | VSC_SATA_INT_ERROR_T | \
+ VSC_SATA_INT_ERROR_P | VSC_SATA_INT_ERROR_R | \
+ VSC_SATA_INT_ERROR_E | VSC_SATA_INT_ERROR_M | \
+ VSC_SATA_INT_PHY_CHANGE),
+};
+
-/* Interrupt register offsets (from chip base address) */
-#define VSC_SATA_INT_STAT_OFFSET 0x00
-#define VSC_SATA_INT_MASK_OFFSET 0x04
-
-/* Taskfile registers offsets */
-#define VSC_SATA_TF_CMD_OFFSET 0x00
-#define VSC_SATA_TF_DATA_OFFSET 0x00
-#define VSC_SATA_TF_ERROR_OFFSET 0x04
-#define VSC_SATA_TF_FEATURE_OFFSET 0x06
-#define VSC_SATA_TF_NSECT_OFFSET 0x08
-#define VSC_SATA_TF_LBAL_OFFSET 0x0c
-#define VSC_SATA_TF_LBAM_OFFSET 0x10
-#define VSC_SATA_TF_LBAH_OFFSET 0x14
-#define VSC_SATA_TF_DEVICE_OFFSET 0x18
-#define VSC_SATA_TF_STATUS_OFFSET 0x1c
-#define VSC_SATA_TF_COMMAND_OFFSET 0x1d
-#define VSC_SATA_TF_ALTSTATUS_OFFSET 0x28
-#define VSC_SATA_TF_CTL_OFFSET 0x29
-
-/* DMA base */
-#define VSC_SATA_UP_DESCRIPTOR_OFFSET 0x64
-#define VSC_SATA_UP_DATA_BUFFER_OFFSET 0x6C
-#define VSC_SATA_DMA_CMD_OFFSET 0x70
-
-/* SCRs base */
-#define VSC_SATA_SCR_STATUS_OFFSET 0x100
-#define VSC_SATA_SCR_ERROR_OFFSET 0x104
-#define VSC_SATA_SCR_CONTROL_OFFSET 0x108
-
-/* Port stride */
-#define VSC_SATA_PORT_OFFSET 0x200
-
-/* Error interrupt status bit offsets */
-#define VSC_SATA_INT_ERROR_E_OFFSET 2
-#define VSC_SATA_INT_ERROR_P_OFFSET 4
-#define VSC_SATA_INT_ERROR_T_OFFSET 5
-#define VSC_SATA_INT_ERROR_M_OFFSET 1
#define is_vsc_sata_int_err(port_idx, int_status) \
- (int_status & ((1 << (VSC_SATA_INT_ERROR_E_OFFSET + (8 * port_idx))) | \
- (1 << (VSC_SATA_INT_ERROR_P_OFFSET + (8 * port_idx))) | \
- (1 << (VSC_SATA_INT_ERROR_T_OFFSET + (8 * port_idx))) | \
- (1 << (VSC_SATA_INT_ERROR_M_OFFSET + (8 * port_idx))) \
- )\
- )
+ (int_status & (VSC_SATA_INT_ERROR << (8 * port_idx)))
static u32 vsc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
@@ -215,14 +221,6 @@ static irqreturn_t vsc_sata_interrupt (i
ap = host_set->ports[i];
- if (is_vsc_sata_int_err(i, int_status)) {
- u32 err_status;
- printk(KERN_DEBUG "%s: ignoring interrupt(s)\n", __FUNCTION__);
- err_status = ap ? vsc_sata_scr_read(ap, SCR_ERROR) : 0;
- vsc_sata_scr_write(ap, SCR_ERROR, err_status);
- handled++;
- }
-
if (ap && !(ap->flags &
(ATA_FLAG_PORT_DISABLED|ATA_FLAG_NOINTR))) {
struct ata_queued_cmd *qc;
@@ -230,12 +228,26 @@ static irqreturn_t vsc_sata_interrupt (i
qc = ata_qc_from_tag(ap, ap->active_tag);
if (qc && (!(qc->tf.ctl & ATA_NIEN))) {
handled += ata_host_intr(ap, qc);
- } else {
- printk(KERN_DEBUG "%s: ignoring interrupt(s)\n", __FUNCTION__);
+ } else if (is_vsc_sata_int_err(i, int_status)) {
+ /*
+ * On some chips (i.e. Intel 31244), an error
+ * interrupt will sneak in at initialization
+ * time (phy state changes). Clearing the SCR
+ * error register is not required, but it prevents
+ * the phy state change interrupts from recurring
+ * later.
+ */
+ u32 err_status;
+ err_status = vsc_sata_scr_read(ap, SCR_ERROR);
+ printk(KERN_DEBUG "%s: clearing interrupt, "
+ "status %x; sata err status %x\n",
+ __FUNCTION__,
+ int_status, err_status);
+ vsc_sata_scr_write(ap, SCR_ERROR, err_status);
+ /* Clear interrupt status */
ata_chk_status(ap);
handled++;
}
-
}
}
}
diff --git a/include/linux/ata.h b/include/linux/ata.h
index b02a16c..312a2c0 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -146,6 +146,8 @@ enum {
ATA_CMD_STANDBYNOW1 = 0xE0,
ATA_CMD_IDLEIMMEDIATE = 0xE1,
ATA_CMD_INIT_DEV_PARAMS = 0x91,
+ ATA_CMD_READ_NATIVE_MAX = 0xF8,
+ ATA_CMD_READ_NATIVE_MAX_EXT = 0x27,
/* SETFEATURES stuff */
SETFEATURES_XFER = 0x03,
@@ -204,7 +206,6 @@ enum ata_tf_protocols {
ATA_PROT_UNKNOWN, /* unknown/invalid */
ATA_PROT_NODATA, /* no data */
ATA_PROT_PIO, /* PIO single sector */
- ATA_PROT_PIO_MULT, /* PIO multiple sector */
ATA_PROT_DMA, /* DMA */
ATA_PROT_ATAPI, /* packet command, PIO data xfer*/
ATA_PROT_ATAPI_NODATA, /* packet command, no data */
@@ -247,18 +248,22 @@ struct ata_taskfile {
};
#define ata_id_is_ata(id) (((id)[0] & (1 << 15)) == 0)
+#define ata_id_is_cfa(id) ((id)[0] == 0x848A)
#define ata_id_is_sata(id) ((id)[93] == 0)
#define ata_id_rahead_enabled(id) ((id)[85] & (1 << 6))
#define ata_id_wcache_enabled(id) ((id)[85] & (1 << 5))
+#define ata_id_hpa_enabled(id) ((id)[85] & (1 << 10))
#define ata_id_has_fua(id) ((id)[84] & (1 << 6))
#define ata_id_has_flush(id) ((id)[83] & (1 << 12))
#define ata_id_has_flush_ext(id) ((id)[83] & (1 << 13))
#define ata_id_has_lba48(id) ((id)[83] & (1 << 10))
+#define ata_id_has_hpa(id) ((id)[82] & (1 << 10))
#define ata_id_has_wcache(id) ((id)[82] & (1 << 5))
#define ata_id_has_pm(id) ((id)[82] & (1 << 3))
#define ata_id_has_lba(id) ((id)[49] & (1 << 9))
#define ata_id_has_dma(id) ((id)[49] & (1 << 8))
#define ata_id_removeable(id) ((id)[0] & (1 << 7))
+#define ata_id_has_dword_io(id) ((id)[50] & (1 << 0))
#define ata_id_u32(id,n) \
(((u32) (id)[(n) + 1] << 16) | ((u32) (id)[(n)]))
#define ata_id_u64(id,n) \
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 204c37a..7a54244 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -502,6 +502,7 @@ extern int ata_pci_init_one (struct pci_
extern void ata_pci_remove_one (struct pci_dev *pdev);
extern int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t state);
extern int ata_pci_device_resume(struct pci_dev *pdev);
+extern int ata_pci_clear_simplex(struct pci_dev *pdev);
#endif /* CONFIG_PCI */
extern int ata_device_add(const struct ata_probe_ent *ent);
extern void ata_host_set_remove(struct ata_host_set *host_set);
@@ -542,6 +543,7 @@ extern void ata_port_stop (struct ata_po
extern void ata_host_stop (struct ata_host_set *host_set);
extern irqreturn_t ata_interrupt (int irq, void *dev_instance, struct pt_regs *regs);
extern void ata_qc_prep(struct ata_queued_cmd *qc);
+extern void ata_noop_qc_prep(struct ata_queued_cmd *qc);
extern unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc);
extern void ata_sg_init_one(struct ata_queued_cmd *qc, void *buf,
unsigned int buflen);
@@ -608,7 +610,7 @@ extern void ata_pci_host_stop (struct at
extern struct ata_probe_ent *
ata_pci_init_native_mode(struct pci_dev *pdev, struct ata_port_info **port, int portmask);
extern int pci_test_config_bits(struct pci_dev *pdev, const struct pci_bits *bits);
-
+extern unsigned long ata_pci_default_filter(const struct ata_port *, struct ata_device *, unsigned long);
#endif /* CONFIG_PCI */
^ permalink raw reply related [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2006-03-21 16:40 ` Jeff Garzik
@ 2006-03-21 17:23 ` Alan Cox
0 siblings, 0 replies; 95+ messages in thread
From: Alan Cox @ 2006-03-21 17:23 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-ide, linux-kernel
On Maw, 2006-03-21 at 11:40 -0500, Jeff Garzik wrote:
> Alan Cox wrote:
> To be specific, are the patches against libata-dev.git 'upstream' branch?
Yes
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2006-03-21 10:20 ` Alan Cox
@ 2006-03-21 16:40 ` Jeff Garzik
2006-03-21 17:23 ` Alan Cox
0 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2006-03-21 16:40 UTC (permalink / raw)
To: Alan Cox; +Cc: linux-ide, linux-kernel
Alan Cox wrote:
> On Llu, 2006-03-20 at 20:12 -0500, Jeff Garzik wrote:
>
>>In my [no doubt warped] brain, I equate the SFF-8038 interface to "PCI
>>IDE BMDMA", and from there, view most hardware as a subset of PCI IDE
>>BMDMA. It might not do DMA, might not be PCI, might not do irqs, but
>>most PATA hardware seems able to be driven by a "bmdma driver". Thus,
>>the name :)
>
>
> Most of that file is ST-506 type register interfaces, only a tiny bit is
> SFF PCI IDE with DMA.
>
> Expect some patches soon. I've got my tree merged against the git tree
> now, just needs some testing.
To be specific, are the patches against libata-dev.git 'upstream' branch?
(most should apply to Linus-vanilla branch, so regardless of the
definition of "the git tree" it should be OK)
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2006-03-21 1:12 ` Jeff Garzik
@ 2006-03-21 10:20 ` Alan Cox
2006-03-21 16:40 ` Jeff Garzik
0 siblings, 1 reply; 95+ messages in thread
From: Alan Cox @ 2006-03-21 10:20 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-ide, linux-kernel
On Llu, 2006-03-20 at 20:12 -0500, Jeff Garzik wrote:
> In my [no doubt warped] brain, I equate the SFF-8038 interface to "PCI
> IDE BMDMA", and from there, view most hardware as a subset of PCI IDE
> BMDMA. It might not do DMA, might not be PCI, might not do irqs, but
> most PATA hardware seems able to be driven by a "bmdma driver". Thus,
> the name :)
Most of that file is ST-506 type register interfaces, only a tiny bit is
SFF PCI IDE with DMA.
Expect some patches soon. I've got my tree merged against the git tree
now, just needs some testing.
Alan
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2006-03-20 16:35 ` Alan Cox
@ 2006-03-21 1:12 ` Jeff Garzik
2006-03-21 10:20 ` Alan Cox
0 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2006-03-21 1:12 UTC (permalink / raw)
To: Alan Cox; +Cc: linux-ide, linux-kernel
Alan Cox wrote:
> On Llu, 2006-03-20 at 06:16 -0500, Jeff Garzik wrote:
>
>>Jeff Garzik:
>> [libata] Move PCI IDE BMDMA-related code to new file libata-bmdma.c.
>
>
> This is a most confusing choice as 80% of the file has nothing to do
> with bus mastering DMA, and a large amount of it has nothing to do with
> PCI either. Also lots of DMA stuff is in the drivers so all the new bus
> mastering drivers don't use bmdma.c
>
> The split makes sense, the choice of name is peculiar, if not completely
> broken 8)
Peculiar? Probably... :)
In my [no doubt warped] brain, I equate the SFF-8038 interface to "PCI
IDE BMDMA", and from there, view most hardware as a subset of PCI IDE
BMDMA. It might not do DMA, might not be PCI, might not do irqs, but
most PATA hardware seems able to be driven by a "bmdma driver". Thus,
the name :)
Jeff
^ permalink raw reply [flat|nested] 95+ messages in thread
* Re: [git patches] libata updates
2006-03-20 11:16 Jeff Garzik
@ 2006-03-20 16:35 ` Alan Cox
2006-03-21 1:12 ` Jeff Garzik
0 siblings, 1 reply; 95+ messages in thread
From: Alan Cox @ 2006-03-20 16:35 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-ide, linux-kernel
On Llu, 2006-03-20 at 06:16 -0500, Jeff Garzik wrote:
> Jeff Garzik:
> [libata] Move PCI IDE BMDMA-related code to new file libata-bmdma.c.
This is a most confusing choice as 80% of the file has nothing to do
with bus mastering DMA, and a large amount of it has nothing to do with
PCI either. Also lots of DMA stuff is in the drivers so all the new bus
mastering drivers don't use bmdma.c
The split makes sense, the choice of name is peculiar, if not completely
broken 8)
Alan
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2006-03-20 11:16 Jeff Garzik
2006-03-20 16:35 ` Alan Cox
0 siblings, 1 reply; 95+ messages in thread
From: Jeff Garzik @ 2006-03-20 11:16 UTC (permalink / raw)
To: linux-ide; +Cc: linux-kernel
[just sent upstream; patch snipped due to size]
Please pull from 'upstream-linus' branch of
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev.git
to receive the following updates:
drivers/scsi/Makefile | 2
drivers/scsi/ahci.c | 197 +-
drivers/scsi/ata_piix.c | 392 +++--
drivers/scsi/libata-bmdma.c | 703 ++++++++++
drivers/scsi/libata-core.c | 2984 +++++++++++++++++++++-----------------------
drivers/scsi/libata-scsi.c | 240 ++-
drivers/scsi/libata.h | 3
drivers/scsi/pdc_adma.c | 6
drivers/scsi/sata_mv.c | 279 +++-
drivers/scsi/sata_nv.c | 2
drivers/scsi/sata_promise.c | 129 +
drivers/scsi/sata_qstor.c | 10
drivers/scsi/sata_sil.c | 128 -
drivers/scsi/sata_sil24.c | 102 -
drivers/scsi/sata_sis.c | 2
drivers/scsi/sata_svw.c | 2
drivers/scsi/sata_sx4.c | 25
drivers/scsi/sata_uli.c | 2
drivers/scsi/sata_via.c | 2
drivers/scsi/sata_vsc.c | 2
drivers/scsi/scsi_error.c | 7
include/linux/ata.h | 22
include/linux/libata.h | 180 ++
include/scsi/scsi_eh.h | 3
24 files changed, 3312 insertions(+), 2112 deletions(-)
Albert Lee:
libata CHS: LBA28/LBA48 optimization (revise #6)
Daniel Drake:
sata_promise: Support FastTrak TX4300/TX4310
Jeff Garzik:
[libata ata_piix] Fix ICH6/7 map value interpretation
[libata sata_mv] add 6042 support, fix 60xx/50xx EDMA configuration
[libata scsi] build fix for ATA_FLAG_IN_EH change
[libata] Move PCI IDE BMDMA-related code to new file libata-bmdma.c.
libata: turn on ATAPI by default
Luke Kosewski:
[libata sata_promise] add correct read/write of hotplug registers for SATAII devices
Randy Dunlap:
Various libata documentation updates.
Tejun Heo:
libata: separate out ata_sata_print_link_status
ahci: separate out ahci_stop/start_engine
ahci: separate out ahci_dev_classify
ata_piix: fix MAP VALUE interpretation for for ICH6/7
libata: fold __ata_qc_complete() into ata_qc_free()
libata: make the owner of a qc responsible for freeing it
libata: fix ata_qc_issue() error handling
ahci: fix err_mask setting in ahci_host_intr
libata: add detailed AC_ERR_* flags
libata: return AC_ERR_* from issue functions
SCSI: export scsi_eh_finish_cmd() and scsi_eh_flush_done_q()
libata: implement and apply ata_eh_qc_complete/retry()
libata: create pio/atapi task queueing wrappers
ahci: stop engine during hard reset
ahci: add constants for SRST
libata: export ata_busy_sleep
libata: modify ata_dev_try_classify
libata: new ->probe_reset operation
libata: implement ata_drive_probe_reset()
libata: implement standard reset component operations and ->probe_reset
libata: implement ATA_FLAG_IN_EH port flag
libata: EH / pio tasks synchronization
libata: fix ata_std_probe_reset() SATA detection
libata: separate out sata_phy_resume() from sata_std_hardreset()
libata: add probeinit component operation to ata_drive_probe_reset()
libata: implement ata_std_probeinit()
libata: add ATA_QCFLAG_EH_SCHEDULED
libata: implement ata_scsi_timed_out()
libata: use ata_scsi_timed_out()
libata: kill NULL qc handling from ->eng_timeout callbacks
ahci: separate out ahci_fill_cmd_slot()
libata: make new reset act identical to ->phy_reset register-wise
libata: kill SError clearing in sata_std_hardreset().
sata_sil: convert to new reset mechanism
sata_sil24: convert to new reset mechanism
sata_sil24: add hardreset
libata: inline ata_qc_complete()
ahci: make ahci_fill_cmd_slot() take *pp instead of *ap
ahci: convert to new reset mechanism
libata: convert assert(X)'s in libata core layer to WARN_ON(!X)'s
libata: convert assert(xxx)'s in low-level drivers to WARN_ON(!xxx)'s
libata: kill assert() macro
libata: allow ->probe_reset to return ATA_DEV_UNKNOWN
ata_piix: kill spurious assignment in piix_sata_probe()
libata: implement ata_dev_id_c_string()
libata: use ata_dev_id_c_string()
libata: separate out ata_id_n_sectors()
libata: separate out ata_id_major_version()
libata: make ata_dump_id() take @id instead of @dev
libata: don't do EDD handling if ->probe_reset is used
libata: make ata_dev_knobble() per-device
libata: move cdb_len for host to device
libata: add per-device max_sectors
libata: kill sht->max_sectors
libata: rename ata_dev_id_[c_]string()
libata: update ata_dev_init_params()
libata: fix comment regarding setting cable type
ata_piix: convert pata to new reset mechanism
ata_piix: convert sata to new reset mechanism
libata: separate out ata_dev_read_id()
libata: kill ata_dev_reread_id()
sata_sil24: add a new PCI ID for SiI 3124
libata: kill illegal kfree(id)
sata_sil: remove unneeded ATA_FLAG_SRST from 3512 port info
libata: seperate out ata_class_present()
ata_piix: finer-grained port_info
ata_piix: add a couple of flags
ata_piix: implement proper port map
ata_piix: reimplement piix_sata_probe()
libata: convert dev->id to pointer
libata: separate out ata_dev_configure()
libata: fold ata_dev_config() into ata_dev_configure()
libata: reorganize ata_bus_probe()
ata_piix: rename PIIX_FLAG_IGN_PRESENT to PIIX_FLAG_IGNORE_PCS
sata_sil: replace sil_3112_m15w board id with sil_3112
sata_sil: use kzalloc
sata_sil: replace register address constants with sil_port[] entry
sata_sil: cosmetic flag/constant changes
libata: re-initialize parameters before configuring
libata: add @print_info argument to ata_dev_configure()
libata: implement ata_dev_revalidate()
libata: revalidate after transfer mode configuration
sata_sil24: fix mwdma_mask setting
libata: implement port_task
libata: convert pio_task and packet_task to port_task
libata: kill unused pio_task and packet_task
libata: rename ATA_FLAG_FLUSH_PIO_TASK to ATA_FLAG_FLUSH_PORT_TASK
libata: improve xfer mask constants and update ata_mode_string()
libata: add xfer_mask handling functions
libata: use ata_id_xfermask() in ata_dev_configure()
libata: use xfer_mask helpers in ata_dev_set_mode()
libata: reimplement ata_set_mode() using xfer_mask helpers
libata: kill unused xfer_mode functions
libata: fix missing classes[] initialization in ata_bus_probe()
sata_sil24: exit early from softreset if SStatus reports no device
sata_sil24: lengthen softreset timeout
ahci: enable prefetching for PACKET commands
libata: fix class handling in ata_bus_probe()
libata: check Word 88 validity in ata_id_xfer_mask()
libata: use local *id instead of dev->id in ata_dev_configure()
libata: move IDENTIFY info printing from ata_dev_read_id() to ata_dev_configure()
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2005-09-23 23:11 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2005-09-23 23:11 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, linux-kernel
Please pull from 'upstream' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git
to receive the following changes.
The main fix is the change to include/linux/pci_ids.h, the rest is minor
stuff. The description "Add NVIDIA device ID" is incorrect -- my
mistake. It adds a device id, but also fixes another.
drivers/scsi/ata_piix.c | 1
drivers/scsi/libata-core.c | 81 +++++++++++++++++++++++++++------------------
drivers/scsi/sata_nv.c | 2 +
include/linux/libata.h | 1
include/linux/pci_ids.h | 3 +
5 files changed, 54 insertions(+), 34 deletions(-)
Alan Cox:
PATCH: silly in piix driver
PATCH: remove function for non-PCI as requested
Andy Currid:
Add NVIDIA device ID in sata_nv
diff --git a/drivers/scsi/ata_piix.c b/drivers/scsi/ata_piix.c
--- a/drivers/scsi/ata_piix.c
+++ b/drivers/scsi/ata_piix.c
@@ -442,7 +442,6 @@ static void piix_sata_phy_reset(struct a
* piix_set_piomode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
* @adev: um
- * @pio: PIO mode, 0 - 4
*
* Set PIO mode for device, in host controller PCI config space.
*
diff --git a/drivers/scsi/libata-core.c b/drivers/scsi/libata-core.c
--- a/drivers/scsi/libata-core.c
+++ b/drivers/scsi/libata-core.c
@@ -4132,6 +4132,53 @@ err_out:
}
/**
+ * ata_host_set_remove - PCI layer callback for device removal
+ * @host_set: ATA host set that was removed
+ *
+ * Unregister all objects associated with this host set. Free those
+ * objects.
+ *
+ * LOCKING:
+ * Inherited from calling layer (may sleep).
+ */
+
+
+void ata_host_set_remove(struct ata_host_set *host_set)
+{
+ struct ata_port *ap;
+ unsigned int i;
+
+ for (i = 0; i < host_set->n_ports; i++) {
+ ap = host_set->ports[i];
+ scsi_remove_host(ap->host);
+ }
+
+ free_irq(host_set->irq, host_set);
+
+ for (i = 0; i < host_set->n_ports; i++) {
+ ap = host_set->ports[i];
+
+ ata_scsi_release(ap->host);
+
+ if ((ap->flags & ATA_FLAG_NO_LEGACY) == 0) {
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+
+ if (ioaddr->cmd_addr == 0x1f0)
+ release_region(0x1f0, 8);
+ else if (ioaddr->cmd_addr == 0x170)
+ release_region(0x170, 8);
+ }
+
+ scsi_host_put(ap->host);
+ }
+
+ if (host_set->ops->host_stop)
+ host_set->ops->host_stop(host_set);
+
+ kfree(host_set);
+}
+
+/**
* ata_scsi_release - SCSI layer callback hook for host unload
* @host: libata host to be unloaded
*
@@ -4471,39 +4518,8 @@ void ata_pci_remove_one (struct pci_dev
{
struct device *dev = pci_dev_to_dev(pdev);
struct ata_host_set *host_set = dev_get_drvdata(dev);
- struct ata_port *ap;
- unsigned int i;
-
- for (i = 0; i < host_set->n_ports; i++) {
- ap = host_set->ports[i];
-
- scsi_remove_host(ap->host);
- }
-
- free_irq(host_set->irq, host_set);
-
- for (i = 0; i < host_set->n_ports; i++) {
- ap = host_set->ports[i];
-
- ata_scsi_release(ap->host);
-
- if ((ap->flags & ATA_FLAG_NO_LEGACY) == 0) {
- struct ata_ioports *ioaddr = &ap->ioaddr;
-
- if (ioaddr->cmd_addr == 0x1f0)
- release_region(0x1f0, 8);
- else if (ioaddr->cmd_addr == 0x170)
- release_region(0x170, 8);
- }
-
- scsi_host_put(ap->host);
- }
-
- if (host_set->ops->host_stop)
- host_set->ops->host_stop(host_set);
-
- kfree(host_set);
+ ata_host_set_remove(host_set);
pci_release_regions(pdev);
pci_disable_device(pdev);
dev_set_drvdata(dev, NULL);
@@ -4573,6 +4589,7 @@ module_exit(ata_exit);
EXPORT_SYMBOL_GPL(ata_std_bios_param);
EXPORT_SYMBOL_GPL(ata_std_ports);
EXPORT_SYMBOL_GPL(ata_device_add);
+EXPORT_SYMBOL_GPL(ata_host_set_remove);
EXPORT_SYMBOL_GPL(ata_sg_init);
EXPORT_SYMBOL_GPL(ata_sg_init_one);
EXPORT_SYMBOL_GPL(ata_qc_complete);
diff --git a/drivers/scsi/sata_nv.c b/drivers/scsi/sata_nv.c
--- a/drivers/scsi/sata_nv.c
+++ b/drivers/scsi/sata_nv.c
@@ -158,6 +158,8 @@ static struct pci_device_id nv_pci_tbl[]
PCI_ANY_ID, PCI_ANY_ID, 0, 0, MCP51 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, MCP55 },
+ { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA2,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, MCP55 },
{ PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID,
PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_STORAGE_IDE<<8, 0xffff00, GENERIC },
diff --git a/include/linux/libata.h b/include/linux/libata.h
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -393,6 +393,7 @@ extern int ata_pci_init_one (struct pci_
extern void ata_pci_remove_one (struct pci_dev *pdev);
#endif /* CONFIG_PCI */
extern int ata_device_add(struct ata_probe_ent *ent);
+extern void ata_host_set_remove(struct ata_host_set *host_set);
extern int ata_scsi_detect(Scsi_Host_Template *sht);
extern int ata_scsi_ioctl(struct scsi_device *dev, int cmd, void __user *arg);
extern int ata_scsi_queuecmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *));
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -1268,7 +1268,8 @@
#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA 0x0266
#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2 0x0267
#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE 0x036E
-#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA 0x036F
+#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA 0x037E
+#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA2 0x037F
#define PCI_DEVICE_ID_NVIDIA_NVENET_12 0x0268
#define PCI_DEVICE_ID_NVIDIA_NVENET_13 0x0269
#define PCI_DEVICE_ID_NVIDIA_MCP51_AUDIO 0x026B
^ permalink raw reply [flat|nested] 95+ messages in thread
* [git patches] libata updates
@ 2005-09-07 6:10 Jeff Garzik
0 siblings, 0 replies; 95+ messages in thread
From: Jeff Garzik @ 2005-09-07 6:10 UTC (permalink / raw)
To: Andrew Morton, Linus Torvalds; +Cc: linux-ide, linux-kernel
Please pull from 'upstream' branch of
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev.git
to obtain the fixes, and new driver, described below:
drivers/scsi/Kconfig | 9
drivers/scsi/Makefile | 1
drivers/scsi/ahci.c | 2
drivers/scsi/sata_mv.c | 843 ++++++++++++++++++++++++++++++++++++++++++++++++
drivers/scsi/sata_uli.c | 4
5 files changed, 856 insertions(+), 3 deletions(-)
commit ca20aa6954bcb4537064a1bf5e8f74af57da2a03
Author: Jeff Garzik <jgarzik@pobox.com>
Date: Wed Sep 7 02:05:59 2005 -0400
[libata sata_mv] fix build
This function will go away when pci_intx() finally makes it
into the core PCI layer.
commit 20f733e7d75a16bffc34842b7682c9247dd5f954
Author: Brett Russ <russb@emc.com>
Date: Thu Sep 1 18:26:17 2005 -0400
[PATCH] libata: Marvell SATA support (PIO mode)
This is my libata compatible low level driver for the Marvell SATA
family. Currently it successfully runs in PIO mode on a 6081 chip.
EDMA support is in the works and should be done shortly. Review,
testing (especially on other flavors of Marvell), comments welcome.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
commit 7da79312830e6d9b3f6ee06b86c3a35caba2f6e7
Author: Brett Russ <russb@emc.com>
Date: Thu Sep 1 21:53:34 2005 -0400
[PATCH] libata: fix pio_mask values (take 2)
ata_get_mode_mask() uses bits 3 and 4 in the pio_mask to represent PIO
modes 3 and 4. The value read from the drive, which reports support
for PIO3 and PIO4 in bits 0 and 1, is shifted left by 3 bits and OR'd
with 0x7 (which then corresponds to PIO 2-0 in libata). Thus, the
drivers below need adjustments to comply with the way pio_mask is
used. I changed the masks from the commented values to all support
PIO4-0, since the spec mandates that PIO0-2 are supported and there's
no reason not to support PIO3 IMO.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -459,6 +459,15 @@ config SCSI_ATA_PIIX
If unsure, say N.
+config SCSI_SATA_MV
+ tristate "Marvell SATA support"
+ depends on SCSI_SATA && PCI && EXPERIMENTAL
+ help
+ This option enables support for the Marvell Serial ATA family.
+ Currently supports 88SX[56]0[48][01] chips.
+
+ If unsure, say N.
+
config SCSI_SATA_NV
tristate "NVIDIA SATA support"
depends on SCSI_SATA && PCI && EXPERIMENTAL
diff --git a/drivers/scsi/Makefile b/drivers/scsi/Makefile
--- a/drivers/scsi/Makefile
+++ b/drivers/scsi/Makefile
@@ -132,6 +132,7 @@ obj-$(CONFIG_SCSI_SATA_SIS) += libata.o
obj-$(CONFIG_SCSI_SATA_SX4) += libata.o sata_sx4.o
obj-$(CONFIG_SCSI_SATA_NV) += libata.o sata_nv.o
obj-$(CONFIG_SCSI_SATA_ULI) += libata.o sata_uli.o
+obj-$(CONFIG_SCSI_SATA_MV) += libata.o sata_mv.o
obj-$(CONFIG_ARM) += arm/
diff --git a/drivers/scsi/ahci.c b/drivers/scsi/ahci.c
--- a/drivers/scsi/ahci.c
+++ b/drivers/scsi/ahci.c
@@ -250,7 +250,7 @@ static struct ata_port_info ahci_port_in
.host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO |
ATA_FLAG_PIO_DMA,
- .pio_mask = 0x03, /* pio3-4 */
+ .pio_mask = 0x1f, /* pio0-4 */
.udma_mask = 0x7f, /* udma0-6 ; FIXME */
.port_ops = &ahci_ops,
},
diff --git a/drivers/scsi/sata_mv.c b/drivers/scsi/sata_mv.c
new file mode 100644
--- /dev/null
+++ b/drivers/scsi/sata_mv.c
@@ -0,0 +1,843 @@
+/*
+ * sata_mv.c - Marvell SATA support
+ *
+ * Copyright 2005: EMC Corporation, all rights reserved.
+ *
+ * Please ALWAYS copy linux-ide@vger.kernel.org on emails.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/dma-mapping.h>
+#include "scsi.h"
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <asm/io.h>
+
+#define DRV_NAME "sata_mv"
+#define DRV_VERSION "0.12"
+
+enum {
+ /* BAR's are enumerated in terms of pci_resource_start() terms */
+ MV_PRIMARY_BAR = 0, /* offset 0x10: memory space */
+ MV_IO_BAR = 2, /* offset 0x18: IO space */
+ MV_MISC_BAR = 3, /* offset 0x1c: FLASH, NVRAM, SRAM */
+
+ MV_MAJOR_REG_AREA_SZ = 0x10000, /* 64KB */
+ MV_MINOR_REG_AREA_SZ = 0x2000, /* 8KB */
+
+ MV_PCI_REG_BASE = 0,
+ MV_IRQ_COAL_REG_BASE = 0x18000, /* 6xxx part only */
+ MV_SATAHC0_REG_BASE = 0x20000,
+
+ MV_PCI_REG_SZ = MV_MAJOR_REG_AREA_SZ,
+ MV_SATAHC_REG_SZ = MV_MAJOR_REG_AREA_SZ,
+ MV_SATAHC_ARBTR_REG_SZ = MV_MINOR_REG_AREA_SZ, /* arbiter */
+ MV_PORT_REG_SZ = MV_MINOR_REG_AREA_SZ,
+
+ MV_Q_CT = 32,
+ MV_CRQB_SZ = 32,
+ MV_CRPB_SZ = 8,
+
+ MV_DMA_BOUNDARY = 0xffffffffU,
+ SATAHC_MASK = (~(MV_SATAHC_REG_SZ - 1)),
+
+ MV_PORTS_PER_HC = 4,
+ /* == (port / MV_PORTS_PER_HC) to determine HC from 0-7 port */
+ MV_PORT_HC_SHIFT = 2,
+ /* == (port % MV_PORTS_PER_HC) to determine port from 0-7 port */
+ MV_PORT_MASK = 3,
+
+ /* Host Flags */
+ MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */
+ MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */
+ MV_FLAG_BDMA = (1 << 28), /* Basic DMA */
+
+ chip_504x = 0,
+ chip_508x = 1,
+ chip_604x = 2,
+ chip_608x = 3,
+
+ /* PCI interface registers */
+
+ PCI_MAIN_CMD_STS_OFS = 0xd30,
+ STOP_PCI_MASTER = (1 << 2),
+ PCI_MASTER_EMPTY = (1 << 3),
+ GLOB_SFT_RST = (1 << 4),
+
+ PCI_IRQ_CAUSE_OFS = 0x1d58,
+ PCI_IRQ_MASK_OFS = 0x1d5c,
+ PCI_UNMASK_ALL_IRQS = 0x7fffff, /* bits 22-0 */
+
+ HC_MAIN_IRQ_CAUSE_OFS = 0x1d60,
+ HC_MAIN_IRQ_MASK_OFS = 0x1d64,
+ PORT0_ERR = (1 << 0), /* shift by port # */
+ PORT0_DONE = (1 << 1), /* shift by port # */
+ HC0_IRQ_PEND = 0x1ff, /* bits 0-8 = HC0's ports */
+ HC_SHIFT = 9, /* bits 9-17 = HC1's ports */
+ PCI_ERR = (1 << 18),
+ TRAN_LO_DONE = (1 << 19), /* 6xxx: IRQ coalescing */
+ TRAN_HI_DONE = (1 << 20), /* 6xxx: IRQ coalescing */
+ PORTS_0_7_COAL_DONE = (1 << 21), /* 6xxx: IRQ coalescing */
+ GPIO_INT = (1 << 22),
+ SELF_INT = (1 << 23),
+ TWSI_INT = (1 << 24),
+ HC_MAIN_RSVD = (0x7f << 25), /* bits 31-25 */
+ HC_MAIN_MASKED_IRQS = (TRAN_LO_DONE | TRAN_HI_DONE |
+ PORTS_0_7_COAL_DONE | GPIO_INT | TWSI_INT |
+ HC_MAIN_RSVD),
+
+ /* SATAHC registers */
+ HC_CFG_OFS = 0,
+
+ HC_IRQ_CAUSE_OFS = 0x14,
+ CRBP_DMA_DONE = (1 << 0), /* shift by port # */
+ HC_IRQ_COAL = (1 << 4), /* IRQ coalescing */
+ DEV_IRQ = (1 << 8), /* shift by port # */
+
+ /* Shadow block registers */
+ SHD_PIO_DATA_OFS = 0x100,
+ SHD_FEA_ERR_OFS = 0x104,
+ SHD_SECT_CNT_OFS = 0x108,
+ SHD_LBA_L_OFS = 0x10C,
+ SHD_LBA_M_OFS = 0x110,
+ SHD_LBA_H_OFS = 0x114,
+ SHD_DEV_HD_OFS = 0x118,
+ SHD_CMD_STA_OFS = 0x11C,
+ SHD_CTL_AST_OFS = 0x120,
+
+ /* SATA registers */
+ SATA_STATUS_OFS = 0x300, /* ctrl, err regs follow status */
+ SATA_ACTIVE_OFS = 0x350,
+
+ /* Port registers */
+ EDMA_CFG_OFS = 0,
+
+ EDMA_ERR_IRQ_CAUSE_OFS = 0x8,
+ EDMA_ERR_IRQ_MASK_OFS = 0xc,
+ EDMA_ERR_D_PAR = (1 << 0),
+ EDMA_ERR_PRD_PAR = (1 << 1),
+ EDMA_ERR_DEV = (1 << 2),
+ EDMA_ERR_DEV_DCON = (1 << 3),
+ EDMA_ERR_DEV_CON = (1 << 4),
+ EDMA_ERR_SERR = (1 << 5),
+ EDMA_ERR_SELF_DIS = (1 << 7),
+ EDMA_ERR_BIST_ASYNC = (1 << 8),
+ EDMA_ERR_CRBQ_PAR = (1 << 9),
+ EDMA_ERR_CRPB_PAR = (1 << 10),
+ EDMA_ERR_INTRL_PAR = (1 << 11),
+ EDMA_ERR_IORDY = (1 << 12),
+ EDMA_ERR_LNK_CTRL_RX = (0xf << 13),
+ EDMA_ERR_LNK_CTRL_RX_2 = (1 << 15),
+ EDMA_ERR_LNK_DATA_RX = (0xf << 17),
+ EDMA_ERR_LNK_CTRL_TX = (0x1f << 21),
+ EDMA_ERR_LNK_DATA_TX = (0x1f << 26),
+ EDMA_ERR_TRANS_PROTO = (1 << 31),
+ EDMA_ERR_FATAL = (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR |
+ EDMA_ERR_DEV_DCON | EDMA_ERR_CRBQ_PAR |
+ EDMA_ERR_CRPB_PAR | EDMA_ERR_INTRL_PAR |
+ EDMA_ERR_IORDY | EDMA_ERR_LNK_CTRL_RX_2 |
+ EDMA_ERR_LNK_DATA_RX |
+ EDMA_ERR_LNK_DATA_TX |
+ EDMA_ERR_TRANS_PROTO),
+
+ EDMA_CMD_OFS = 0x28,
+ EDMA_EN = (1 << 0),
+ EDMA_DS = (1 << 1),
+ ATA_RST = (1 << 2),
+
+ /* BDMA is 6xxx part only */
+ BDMA_CMD_OFS = 0x224,
+ BDMA_START = (1 << 0),
+
+ MV_UNDEF = 0,
+};
+
+struct mv_port_priv {
+
+};
+
+struct mv_host_priv {
+
+};
+
+static void mv_irq_clear(struct ata_port *ap);
+static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in);
+static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
+static void mv_phy_reset(struct ata_port *ap);
+static int mv_master_reset(void __iomem *mmio_base);
+static irqreturn_t mv_interrupt(int irq, void *dev_instance,
+ struct pt_regs *regs);
+static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
+
+static Scsi_Host_Template mv_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .eh_strategy_handler = ata_scsi_error,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = MV_UNDEF,
+ .max_sectors = ATA_MAX_SECTORS,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = MV_UNDEF,
+ .proc_name = DRV_NAME,
+ .dma_boundary = MV_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .bios_param = ata_std_bios_param,
+ .ordered_flush = 1,
+};
+
+static struct ata_port_operations mv_ops = {
+ .port_disable = ata_port_disable,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .phy_reset = mv_phy_reset,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+
+ .eng_timeout = ata_eng_timeout,
+
+ .irq_handler = mv_interrupt,
+ .irq_clear = mv_irq_clear,
+
+ .scr_read = mv_scr_read,
+ .scr_write = mv_scr_write,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_host_stop,
+};
+
+static struct ata_port_info mv_port_info[] = {
+ { /* chip_504x */
+ .sht = &mv_sht,
+ .host_flags = (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+ ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO),
+ .pio_mask = 0x1f, /* pio4-0 */
+ .udma_mask = 0, /* 0x7f (udma6-0 disabled for now) */
+ .port_ops = &mv_ops,
+ },
+ { /* chip_508x */
+ .sht = &mv_sht,
+ .host_flags = (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+ ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO |
+ MV_FLAG_DUAL_HC),
+ .pio_mask = 0x1f, /* pio4-0 */
+ .udma_mask = 0, /* 0x7f (udma6-0 disabled for now) */
+ .port_ops = &mv_ops,
+ },
+ { /* chip_604x */
+ .sht = &mv_sht,
+ .host_flags = (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+ ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO |
+ MV_FLAG_IRQ_COALESCE | MV_FLAG_BDMA),
+ .pio_mask = 0x1f, /* pio4-0 */
+ .udma_mask = 0, /* 0x7f (udma6-0 disabled for now) */
+ .port_ops = &mv_ops,
+ },
+ { /* chip_608x */
+ .sht = &mv_sht,
+ .host_flags = (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+ ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO |
+ MV_FLAG_IRQ_COALESCE | MV_FLAG_DUAL_HC |
+ MV_FLAG_BDMA),
+ .pio_mask = 0x1f, /* pio4-0 */
+ .udma_mask = 0, /* 0x7f (udma6-0 disabled for now) */
+ .port_ops = &mv_ops,
+ },
+};
+
+static struct pci_device_id mv_pci_tbl[] = {
+ {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5040), 0, 0, chip_504x},
+ {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5041), 0, 0, chip_504x},
+ {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5080), 0, 0, chip_508x},
+ {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5081), 0, 0, chip_508x},
+
+ {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6040), 0, 0, chip_604x},
+ {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6041), 0, 0, chip_604x},
+ {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6080), 0, 0, chip_608x},
+ {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6081), 0, 0, chip_608x},
+ {} /* terminate list */
+};
+
+static struct pci_driver mv_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = mv_pci_tbl,
+ .probe = mv_init_one,
+ .remove = ata_pci_remove_one,
+};
+
+/*
+ * Functions
+ */
+
+static inline void writelfl(unsigned long data, void __iomem *addr)
+{
+ writel(data, addr);
+ (void) readl(addr); /* flush to avoid PCI posted write */
+}
+
+static inline void __iomem *mv_port_addr_to_hc_base(void __iomem *port_mmio)
+{
+ return ((void __iomem *)((unsigned long)port_mmio &
+ (unsigned long)SATAHC_MASK));
+}
+
+static inline void __iomem *mv_hc_base(void __iomem *base, unsigned int hc)
+{
+ return (base + MV_SATAHC0_REG_BASE + (hc * MV_SATAHC_REG_SZ));
+}
+
+static inline void __iomem *mv_port_base(void __iomem *base, unsigned int port)
+{
+ return (mv_hc_base(base, port >> MV_PORT_HC_SHIFT) +
+ MV_SATAHC_ARBTR_REG_SZ +
+ ((port & MV_PORT_MASK) * MV_PORT_REG_SZ));
+}
+
+static inline void __iomem *mv_ap_base(struct ata_port *ap)
+{
+ return mv_port_base(ap->host_set->mmio_base, ap->port_no);
+}
+
+static inline int mv_get_hc_count(unsigned long flags)
+{
+ return ((flags & MV_FLAG_DUAL_HC) ? 2 : 1);
+}
+
+static inline int mv_is_edma_active(struct ata_port *ap)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+ return (EDMA_EN & readl(port_mmio + EDMA_CMD_OFS));
+}
+
+static inline int mv_port_bdma_capable(struct ata_port *ap)
+{
+ return (ap->flags & MV_FLAG_BDMA);
+}
+
+static void mv_irq_clear(struct ata_port *ap)
+{
+}
+
+static unsigned int mv_scr_offset(unsigned int sc_reg_in)
+{
+ unsigned int ofs;
+
+ switch (sc_reg_in) {
+ case SCR_STATUS:
+ case SCR_CONTROL:
+ case SCR_ERROR:
+ ofs = SATA_STATUS_OFS + (sc_reg_in * sizeof(u32));
+ break;
+ case SCR_ACTIVE:
+ ofs = SATA_ACTIVE_OFS; /* active is not with the others */
+ break;
+ default:
+ ofs = 0xffffffffU;
+ break;
+ }
+ return ofs;
+}
+
+static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in)
+{
+ unsigned int ofs = mv_scr_offset(sc_reg_in);
+
+ if (0xffffffffU != ofs) {
+ return readl(mv_ap_base(ap) + ofs);
+ } else {
+ return (u32) ofs;
+ }
+}
+
+static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
+{
+ unsigned int ofs = mv_scr_offset(sc_reg_in);
+
+ if (0xffffffffU != ofs) {
+ writelfl(val, mv_ap_base(ap) + ofs);
+ }
+}
+
+static int mv_master_reset(void __iomem *mmio_base)
+{
+ void __iomem *reg = mmio_base + PCI_MAIN_CMD_STS_OFS;
+ int i, rc = 0;
+ u32 t;
+
+ VPRINTK("ENTER\n");
+
+ /* Following procedure defined in PCI "main command and status
+ * register" table.
+ */
+ t = readl(reg);
+ writel(t | STOP_PCI_MASTER, reg);
+
+ for (i = 0; i < 100; i++) {
+ msleep(10);
+ t = readl(reg);
+ if (PCI_MASTER_EMPTY & t) {
+ break;
+ }
+ }
+ if (!(PCI_MASTER_EMPTY & t)) {
+ printk(KERN_ERR DRV_NAME "PCI master won't flush\n");
+ rc = 1; /* broken HW? */
+ goto done;
+ }
+
+ /* set reset */
+ i = 5;
+ do {
+ writel(t | GLOB_SFT_RST, reg);
+ t = readl(reg);
+ udelay(1);
+ } while (!(GLOB_SFT_RST & t) && (i-- > 0));
+
+ if (!(GLOB_SFT_RST & t)) {
+ printk(KERN_ERR DRV_NAME "can't set global reset\n");
+ rc = 1; /* broken HW? */
+ goto done;
+ }
+
+ /* clear reset */
+ i = 5;
+ do {
+ writel(t & ~GLOB_SFT_RST, reg);
+ t = readl(reg);
+ udelay(1);
+ } while ((GLOB_SFT_RST & t) && (i-- > 0));
+
+ if (GLOB_SFT_RST & t) {
+ printk(KERN_ERR DRV_NAME "can't clear global reset\n");
+ rc = 1; /* broken HW? */
+ }
+
+ done:
+ VPRINTK("EXIT, rc = %i\n", rc);
+ return rc;
+}
+
+static void mv_err_intr(struct ata_port *ap)
+{
+ void __iomem *port_mmio;
+ u32 edma_err_cause, serr = 0;
+
+ /* bug here b/c we got an err int on a port we don't know about,
+ * so there's no way to clear it
+ */
+ BUG_ON(NULL == ap);
+ port_mmio = mv_ap_base(ap);
+
+ edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+
+ if (EDMA_ERR_SERR & edma_err_cause) {
+ serr = scr_read(ap, SCR_ERROR);
+ scr_write_flush(ap, SCR_ERROR, serr);
+ }
+ DPRINTK("port %u error; EDMA err cause: 0x%08x SERR: 0x%08x\n",
+ ap->port_no, edma_err_cause, serr);
+
+ /* Clear EDMA now that SERR cleanup done */
+ writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+
+ /* check for fatal here and recover if needed */
+ if (EDMA_ERR_FATAL & edma_err_cause) {
+ mv_phy_reset(ap);
+ }
+}
+
+/* Handle any outstanding interrupts in a single SATAHC
+ */
+static void mv_host_intr(struct ata_host_set *host_set, u32 relevant,
+ unsigned int hc)
+{
+ void __iomem *mmio = host_set->mmio_base;
+ void __iomem *hc_mmio = mv_hc_base(mmio, hc);
+ struct ata_port *ap;
+ struct ata_queued_cmd *qc;
+ u32 hc_irq_cause;
+ int shift, port, port0, hard_port;
+ u8 ata_status;
+
+ if (hc == 0) {
+ port0 = 0;
+ } else {
+ port0 = MV_PORTS_PER_HC;
+ }
+
+ /* we'll need the HC success int register in most cases */
+ hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
+ if (hc_irq_cause) {
+ writelfl(0, hc_mmio + HC_IRQ_CAUSE_OFS);
+ }
+
+ VPRINTK("ENTER, hc%u relevant=0x%08x HC IRQ cause=0x%08x\n",
+ hc,relevant,hc_irq_cause);
+
+ for (port = port0; port < port0 + MV_PORTS_PER_HC; port++) {
+ ap = host_set->ports[port];
+ hard_port = port & MV_PORT_MASK; /* range 0-3 */
+ ata_status = 0xffU;
+
+ if (((CRBP_DMA_DONE | DEV_IRQ) << hard_port) & hc_irq_cause) {
+ BUG_ON(NULL == ap);
+ /* rcv'd new resp, basic DMA complete, or ATA IRQ */
+ /* This is needed to clear the ATA INTRQ.
+ * FIXME: don't read the status reg in EDMA mode!
+ */
+ ata_status = readb((void __iomem *)
+ ap->ioaddr.status_addr);
+ }
+
+ shift = port * 2;
+ if (port >= MV_PORTS_PER_HC) {
+ shift++; /* skip bit 8 in the HC Main IRQ reg */
+ }
+ if ((PORT0_ERR << shift) & relevant) {
+ mv_err_intr(ap);
+ /* FIXME: smart to OR in ATA_ERR? */
+ ata_status = readb((void __iomem *)
+ ap->ioaddr.status_addr) | ATA_ERR;
+ }
+
+ if (ap) {
+ qc = ata_qc_from_tag(ap, ap->active_tag);
+ if (NULL != qc) {
+ VPRINTK("port %u IRQ found for qc, "
+ "ata_status 0x%x\n", port,ata_status);
+ BUG_ON(0xffU == ata_status);
+ /* mark qc status appropriately */
+ ata_qc_complete(qc, ata_status);
+ }
+ }
+ }
+ VPRINTK("EXIT\n");
+}
+
+static irqreturn_t mv_interrupt(int irq, void *dev_instance,
+ struct pt_regs *regs)
+{
+ struct ata_host_set *host_set = dev_instance;
+ unsigned int hc, handled = 0, n_hcs;
+ void __iomem *mmio;
+ u32 irq_stat;
+
+ mmio = host_set->mmio_base;
+ irq_stat = readl(mmio + HC_MAIN_IRQ_CAUSE_OFS);
+ n_hcs = mv_get_hc_count(host_set->ports[0]->flags);
+
+ /* check the cases where we either have nothing pending or have read
+ * a bogus register value which can indicate HW removal or PCI fault
+ */
+ if (!irq_stat || (0xffffffffU == irq_stat)) {
+ return IRQ_NONE;
+ }
+
+ spin_lock(&host_set->lock);
+
+ for (hc = 0; hc < n_hcs; hc++) {
+ u32 relevant = irq_stat & (HC0_IRQ_PEND << (hc * HC_SHIFT));
+ if (relevant) {
+ mv_host_intr(host_set, relevant, hc);
+ handled = 1;
+ }
+ }
+ if (PCI_ERR & irq_stat) {
+ /* FIXME: these are all masked by default, but still need
+ * to recover from them properly.
+ */
+ }
+
+ spin_unlock(&host_set->lock);
+
+ return IRQ_RETVAL(handled);
+}
+
+static void mv_phy_reset(struct ata_port *ap)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+ struct ata_taskfile tf;
+ struct ata_device *dev = &ap->device[0];
+ u32 edma = 0, bdma;
+
+ VPRINTK("ENTER, port %u, mmio 0x%p\n", ap->port_no, port_mmio);
+
+ edma = readl(port_mmio + EDMA_CMD_OFS);
+ if (EDMA_EN & edma) {
+ /* disable EDMA if active */
+ edma &= ~EDMA_EN;
+ writelfl(edma | EDMA_DS, port_mmio + EDMA_CMD_OFS);
+ udelay(1);
+ } else if (mv_port_bdma_capable(ap) &&
+ (bdma = readl(port_mmio + BDMA_CMD_OFS)) & BDMA_START) {
+ /* disable BDMA if active */
+ writelfl(bdma & ~BDMA_START, port_mmio + BDMA_CMD_OFS);
+ }
+
+ writelfl(edma | ATA_RST, port_mmio + EDMA_CMD_OFS);
+ udelay(25); /* allow reset propagation */
+
+ /* Spec never mentions clearing the bit. Marvell's driver does
+ * clear the bit, however.
+ */
+ writelfl(edma & ~ATA_RST, port_mmio + EDMA_CMD_OFS);
+
+ VPRINTK("Done. Now calling __sata_phy_reset()\n");
+
+ /* proceed to init communications via the scr_control reg */
+ __sata_phy_reset(ap);
+
+ if (ap->flags & ATA_FLAG_PORT_DISABLED) {
+ VPRINTK("Port disabled pre-sig. Exiting.\n");
+ return;
+ }
+
+ tf.lbah = readb((void __iomem *) ap->ioaddr.lbah_addr);
+ tf.lbam = readb((void __iomem *) ap->ioaddr.lbam_addr);
+ tf.lbal = readb((void __iomem *) ap->ioaddr.lbal_addr);
+ tf.nsect = readb((void __iomem *) ap->ioaddr.nsect_addr);
+
+ dev->class = ata_dev_classify(&tf);
+ if (!ata_dev_present(dev)) {
+ VPRINTK("Port disabled post-sig: No device present.\n");
+ ata_port_disable(ap);
+ }
+ VPRINTK("EXIT\n");
+}
+
+static void mv_port_init(struct ata_ioports *port, unsigned long base)
+{
+ /* PIO related setup */
+ port->data_addr = base + SHD_PIO_DATA_OFS;
+ port->error_addr = port->feature_addr = base + SHD_FEA_ERR_OFS;
+ port->nsect_addr = base + SHD_SECT_CNT_OFS;
+ port->lbal_addr = base + SHD_LBA_L_OFS;
+ port->lbam_addr = base + SHD_LBA_M_OFS;
+ port->lbah_addr = base + SHD_LBA_H_OFS;
+ port->device_addr = base + SHD_DEV_HD_OFS;
+ port->status_addr = port->command_addr = base + SHD_CMD_STA_OFS;
+ port->altstatus_addr = port->ctl_addr = base + SHD_CTL_AST_OFS;
+ /* unused */
+ port->cmd_addr = port->bmdma_addr = port->scr_addr = 0;
+
+ /* unmask all EDMA error interrupts */
+ writel(~0, (void __iomem *)base + EDMA_ERR_IRQ_MASK_OFS);
+
+ VPRINTK("EDMA cfg=0x%08x EDMA IRQ err cause/mask=0x%08x/0x%08x\n",
+ readl((void __iomem *)base + EDMA_CFG_OFS),
+ readl((void __iomem *)base + EDMA_ERR_IRQ_CAUSE_OFS),
+ readl((void __iomem *)base + EDMA_ERR_IRQ_MASK_OFS));
+}
+
+static int mv_host_init(struct ata_probe_ent *probe_ent)
+{
+ int rc = 0, n_hc, port, hc;
+ void __iomem *mmio = probe_ent->mmio_base;
+ void __iomem *port_mmio;
+
+ if (mv_master_reset(probe_ent->mmio_base)) {
+ rc = 1;
+ goto done;
+ }
+
+ n_hc = mv_get_hc_count(probe_ent->host_flags);
+ probe_ent->n_ports = MV_PORTS_PER_HC * n_hc;
+
+ for (port = 0; port < probe_ent->n_ports; port++) {
+ port_mmio = mv_port_base(mmio, port);
+ mv_port_init(&probe_ent->port[port], (unsigned long)port_mmio);
+ }
+
+ for (hc = 0; hc < n_hc; hc++) {
+ VPRINTK("HC%i: HC config=0x%08x HC IRQ cause=0x%08x\n", hc,
+ readl(mv_hc_base(mmio, hc) + HC_CFG_OFS),
+ readl(mv_hc_base(mmio, hc) + HC_IRQ_CAUSE_OFS));
+ }
+
+ writel(~HC_MAIN_MASKED_IRQS, mmio + HC_MAIN_IRQ_MASK_OFS);
+ writel(PCI_UNMASK_ALL_IRQS, mmio + PCI_IRQ_MASK_OFS);
+
+ VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x "
+ "PCI int cause/mask=0x%08x/0x%08x\n",
+ readl(mmio + HC_MAIN_IRQ_CAUSE_OFS),
+ readl(mmio + HC_MAIN_IRQ_MASK_OFS),
+ readl(mmio + PCI_IRQ_CAUSE_OFS),
+ readl(mmio + PCI_IRQ_MASK_OFS));
+
+ done:
+ return rc;
+}
+
+/* move to PCI layer, integrate w/ MSI stuff */
+static void pci_intx(struct pci_dev *pdev, int enable)
+{
+ u16 pci_command, new;
+
+ pci_read_config_word(pdev, PCI_COMMAND, &pci_command);
+
+ if (enable)
+ new = pci_command & ~PCI_COMMAND_INTX_DISABLE;
+ else
+ new = pci_command | PCI_COMMAND_INTX_DISABLE;
+
+ if (new != pci_command)
+ pci_write_config_word(pdev, PCI_COMMAND, pci_command);
+}
+
+static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ static int printed_version = 0;
+ struct ata_probe_ent *probe_ent = NULL;
+ struct mv_host_priv *hpriv;
+ unsigned int board_idx = (unsigned int)ent->driver_data;
+ void __iomem *mmio_base;
+ int pci_dev_busy = 0;
+ int rc;
+
+ if (!printed_version++) {
+ printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ }
+
+ VPRINTK("ENTER for PCI Bus:Slot.Func=%u:%u.%u\n", pdev->bus->number,
+ PCI_SLOT(pdev->devfn), PCI_FUNC(pdev->devfn));
+
+ rc = pci_enable_device(pdev);
+ if (rc) {
+ return rc;
+ }
+
+ rc = pci_request_regions(pdev, DRV_NAME);
+ if (rc) {
+ pci_dev_busy = 1;
+ goto err_out;
+ }
+
+ pci_intx(pdev, 1);
+
+ probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL);
+ if (probe_ent == NULL) {
+ rc = -ENOMEM;
+ goto err_out_regions;
+ }
+
+ memset(probe_ent, 0, sizeof(*probe_ent));
+ probe_ent->dev = pci_dev_to_dev(pdev);
+ INIT_LIST_HEAD(&probe_ent->node);
+
+ mmio_base = ioremap_nocache(pci_resource_start(pdev, MV_PRIMARY_BAR),
+ pci_resource_len(pdev, MV_PRIMARY_BAR));
+ if (mmio_base == NULL) {
+ rc = -ENOMEM;
+ goto err_out_free_ent;
+ }
+
+ hpriv = kmalloc(sizeof(*hpriv), GFP_KERNEL);
+ if (!hpriv) {
+ rc = -ENOMEM;
+ goto err_out_iounmap;
+ }
+ memset(hpriv, 0, sizeof(*hpriv));
+
+ probe_ent->sht = mv_port_info[board_idx].sht;
+ probe_ent->host_flags = mv_port_info[board_idx].host_flags;
+ probe_ent->pio_mask = mv_port_info[board_idx].pio_mask;
+ probe_ent->udma_mask = mv_port_info[board_idx].udma_mask;
+ probe_ent->port_ops = mv_port_info[board_idx].port_ops;
+
+ probe_ent->irq = pdev->irq;
+ probe_ent->irq_flags = SA_SHIRQ;
+ probe_ent->mmio_base = mmio_base;
+ probe_ent->private_data = hpriv;
+
+ /* initialize adapter */
+ rc = mv_host_init(probe_ent);
+ if (rc) {
+ goto err_out_hpriv;
+ }
+/* mv_print_info(probe_ent); */
+
+ {
+ int b, w;
+ u32 dw[4]; /* hold a line of 16b */
+ VPRINTK("PCI config space:\n");
+ for (b = 0; b < 0x40; ) {
+ for (w = 0; w < 4; w++) {
+ (void) pci_read_config_dword(pdev,b,&dw[w]);
+ b += sizeof(*dw);
+ }
+ VPRINTK("%08x %08x %08x %08x\n",
+ dw[0],dw[1],dw[2],dw[3]);
+ }
+ }
+
+ /* FIXME: check ata_device_add return value */
+ ata_device_add(probe_ent);
+ kfree(probe_ent);
+
+ return 0;
+
+ err_out_hpriv:
+ kfree(hpriv);
+ err_out_iounmap:
+ iounmap(mmio_base);
+ err_out_free_ent:
+ kfree(probe_ent);
+ err_out_regions:
+ pci_release_regions(pdev);
+ err_out:
+ if (!pci_dev_busy) {
+ pci_disable_device(pdev);
+ }
+
+ return rc;
+}
+
+static int __init mv_init(void)
+{
+ return pci_module_init(&mv_pci_driver);
+}
+
+static void __exit mv_exit(void)
+{
+ pci_unregister_driver(&mv_pci_driver);
+}
+
+MODULE_AUTHOR("Brett Russ");
+MODULE_DESCRIPTION("SCSI low-level driver for Marvell SATA controllers");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, mv_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(mv_init);
+module_exit(mv_exit);
diff --git a/drivers/scsi/sata_uli.c b/drivers/scsi/sata_uli.c
--- a/drivers/scsi/sata_uli.c
+++ b/drivers/scsi/sata_uli.c
@@ -125,8 +125,8 @@ static struct ata_port_info uli_port_inf
.sht = &uli_sht,
.host_flags = ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
ATA_FLAG_NO_LEGACY,
- .pio_mask = 0x03, //support pio mode 4 (FIXME)
- .udma_mask = 0x7f, //support udma mode 6
+ .pio_mask = 0x1f, /* pio0-4 */
+ .udma_mask = 0x7f, /* udma0-6 */
.port_ops = &uli_ops,
};
^ permalink raw reply [flat|nested] 95+ messages in thread
end of thread, other threads:[~2013-04-30 23:18 UTC | newest]
Thread overview: 95+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2006-02-01 4:14 [git patches] libata updates Jeff Garzik
-- strict thread matches above, loose matches on Subject: below --
2013-04-30 22:26 Jeff Garzik
2013-04-30 23:18 ` Linus Torvalds
2012-07-25 20:35 Jeff Garzik
2012-07-25 20:43 ` Jeff Garzik
2012-07-25 22:06 ` Linus Torvalds
2012-07-25 22:26 ` Jeff Garzik
2012-07-25 22:31 ` Linus Torvalds
2012-07-25 22:58 ` Jeff Garzik
2012-07-25 23:30 ` Linus Torvalds
2012-07-26 2:10 ` Jeff Garzik
2012-07-26 17:14 ` Linus Torvalds
2012-07-26 7:44 ` Ingo Molnar
2012-07-25 21:38 ` Jeff Garzik
2012-07-26 4:47 ` Aaron Lu
2012-07-26 5:05 ` James Bottomley
2012-07-26 5:17 ` Aaron Lu
2012-07-26 14:58 ` Alan Stern
2011-01-28 8:29 Jeff Garzik
2010-08-04 1:55 Jeff Garzik
2010-08-04 18:32 ` Linus Torvalds
2010-08-04 18:46 ` Jeff Garzik
2010-06-02 18:08 Jeff Garzik
2010-05-28 1:18 Jeff Garzik
2009-12-19 18:13 Jeff Garzik
2009-12-19 19:05 ` Linus Torvalds
2009-12-19 20:11 ` Jeff Garzik
2009-09-17 20:49 Jeff Garzik
2009-09-20 21:05 ` Bartlomiej Zolnierkiewicz
2009-09-22 2:36 ` Jung-Ik (John) Lee
2009-09-28 15:34 ` Bartlomiej Zolnierkiewicz
2009-09-28 20:20 ` Jung-Ik (John) Lee
2009-09-28 20:36 ` Jeff Garzik
2009-09-28 20:49 ` Jung-Ik (John) Lee
2009-10-06 4:24 ` Jeff Garzik
2009-10-06 22:26 ` Bartlomiej Zolnierkiewicz
2009-10-06 23:02 ` Jeff Garzik
2009-06-23 6:06 Jeff Garzik
2009-04-07 1:42 Jeff Garzik
2009-03-25 3:01 Jeff Garzik
2009-02-03 4:27 Jeff Garzik
2009-01-08 21:46 Jeff Garzik
2008-10-28 4:45 Jeff Garzik
2008-08-22 7:04 Jeff Garzik
2008-07-31 6:51 Jeff Garzik
2008-05-19 22:57 Jeff Garzik
2008-05-06 15:48 Jeff Garzik
2008-05-06 16:23 ` Linus Torvalds
2008-04-29 6:25 Jeff Garzik
2008-02-25 22:38 Jeff Garzik
2008-02-06 12:14 Jeff Garzik
2008-02-01 18:33 Jeff Garzik
2008-01-25 23:16 Jeff Garzik
2007-10-25 7:49 Jeff Garzik
2007-10-15 20:20 Jeff Garzik
2007-07-20 15:00 Jeff Garzik
2007-07-12 20:20 Jeff Garzik
2007-07-10 18:36 Jeff Garzik
2007-05-11 22:32 Jeff Garzik
2007-04-29 16:15 Jeff Garzik
2007-04-30 19:52 ` Chuck Ebbert
2007-04-30 20:05 ` Jeff Garzik
2007-04-30 20:22 ` Stephen Clark
2007-04-30 20:31 ` Alan Cox
2007-04-30 20:51 ` alan
2007-04-30 20:31 ` Jeff Garzik
2007-05-01 11:55 ` Stephen Clark
2007-05-01 21:38 ` Jesse Barnes
2007-05-01 22:45 ` Stephen Clark
2007-05-01 22:49 ` Jesse Barnes
2007-05-01 22:49 ` Chuck Ebbert
2007-05-02 0:48 ` Stephen Clark
2007-04-30 22:06 ` Chuck Ebbert
2007-04-30 22:11 ` Jeff Garzik
2007-05-01 21:34 ` Jesse Barnes
2007-05-10 0:18 ` Jeff Garzik
2006-12-14 23:08 Jeff Garzik
2006-12-15 1:14 ` Alan
2006-12-07 12:40 Jeff Garzik
2006-10-04 6:02 Jeff Garzik
2006-10-04 11:47 ` Alan Cox
2006-10-04 14:34 ` Alan Cox
[not found] <20060924162850.GA14323@havoc.gtf.org>
2006-09-24 16:33 ` Jeff Garzik
2006-03-30 22:01 Jeff Garzik
2006-03-24 15:59 Jeff Garzik
2006-03-23 1:15 Jeff Garzik
2006-03-23 1:36 ` Jeff Garzik
2006-03-20 11:16 Jeff Garzik
2006-03-20 16:35 ` Alan Cox
2006-03-21 1:12 ` Jeff Garzik
2006-03-21 10:20 ` Alan Cox
2006-03-21 16:40 ` Jeff Garzik
2006-03-21 17:23 ` Alan Cox
2005-09-23 23:11 Jeff Garzik
2005-09-07 6:10 Jeff Garzik
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).