* Re: md patches in -mm
[not found] ` <17782.28505.303064.964551@cse.unsw.edu.au>
@ 2006-12-15 19:21 ` thunder7
2006-12-15 20:06 ` Andrew Morton
2006-12-15 20:50 ` sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm] Neil Brown
0 siblings, 2 replies; 27+ messages in thread
From: thunder7 @ 2006-12-15 19:21 UTC (permalink / raw)
To: Neil Brown; +Cc: Jurriaan, Andrew Morton, linux-kernel, linux-raid
From: Neil Brown <neilb@suse.de>
Date: Wed, Dec 06, 2006 at 06:20:57PM +1100
> i.e. current -mm is good for 2.6.20 (though I have a few other little
> things I'll be sending in soon, they aren't related to the raid6
> problem).
>
2.6.20-rc1-mm1 doesn't boot on my box, due to the fact that e2fsck gives
Buffer I/O error on device /dev/md0, logical block 0
and after that 1,2,3,4,5,6,7,8,9, at which points it complains it can't
read the superblock. It seems the raid6 problem hasn't gone away
completely, after all.
Find below: dmesg, /proc/mdstat and .config.
Good luck!
Jurriaan
Linux version 2.6.20-rc1-mm1 (jurriaan@middle) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Fri Dec 15 20:07:38 CET 2006
Command line: root=/dev/md2 video=nvidiafb:1600x1200-32@85 atkbd.softrepeat=1
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c800 (usable)
BIOS-e820: 000000000009c800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bfff0000 (usable)
BIOS-e820: 00000000bfff0000 - 00000000bfff3000 (ACPI NVS)
BIOS-e820: 00000000bfff3000 - 00000000c0000000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
Entering add_active_range(0, 0, 156) 0 entries of 256 used
Entering add_active_range(0, 256, 786416) 1 entries of 256 used
Entering add_active_range(0, 1048576, 1310720) 2 entries of 256 used
end_pfn_map = 1310720
DMI 2.3 present.
ACPI: RSDP (v000 Nvidia ) @ 0x00000000000f7d30
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff30c0
ACPI: SSDT (v001 PTLTD POWERNOW 0x00000001 LTP 0x00000001) @ 0x00000000bfff9900
ACPI: SRAT (v001 AMD HAMMER 0x00000001 AMD 0x00000001) @ 0x00000000bfff9b80
ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff9cc0
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff9840
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
Entering add_active_range(0, 0, 156) 0 entries of 256 used
Entering add_active_range(0, 256, 786416) 1 entries of 256 used
Entering add_active_range(0, 1048576, 1310720) 2 entries of 256 used
sizeof(struct page) = 56
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1310720
early_node_map[3] active PFN ranges
0: 0 -> 156
0: 256 -> 786416
0: 1048576 -> 1310720
On node 0 totalpages: 1048460
Node 0 memmap at 0xffff810001000000 size 73400320 first pfn 0xffff810001000000
DMA zone: 56 pages used for memmap
DMA zone: 1873 pages reserved
DMA zone: 2067 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 768040 pages, LIFO batch:31
Normal zone: 3584 pages used for memmap
Normal zone: 258560 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009c000 - 000000000009d000
Nosave address range: 000000000009d000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000f0000
Nosave address range: 00000000000f0000 - 0000000000100000
Nosave address range: 00000000bfff0000 - 00000000bfff3000
Nosave address range: 00000000bfff3000 - 00000000c0000000
Nosave address range: 00000000c0000000 - 00000000e0000000
Nosave address range: 00000000e0000000 - 00000000f0000000
Nosave address range: 00000000f0000000 - 00000000fec00000
Nosave address range: 00000000fec00000 - 0000000100000000
Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
PERCPU: Allocating 32384 bytes of per cpu data
Built 1 zonelists. Total pages: 1028667
Kernel command line: root=/dev/md2 video=nvidiafb:1600x1200-32@85 atkbd.softrepeat=1
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
CPU 0: aperture @ 8000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 8000000
Memory: 4042548k/5242880k available (3978k kernel code, 151080k reserved, 2440k data, 284k init)
Calibrating delay using timer specific routine.. 4828.64 BogoMIPS (lpj=8044237)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Freeing SMP alternatives: 44k freed
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12564458
Detected 12.564 MHz APIC timer.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4826.47 BogoMIPS (lpj=8040761)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 01
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff -80 cycles, maxerr 624 cycles)
Brought up 2 CPUs
Disabling vsyscall due to use of PM timer
time.c: Using 3.579545 MHz WALL PM GTOD PM timer.
time.c: Detected 2412.373 MHz processor.
migration_cost=215
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000-efffffff
PCI: No mmconfig possible on device 00:18
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:09.0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
Generic PHY: Registered new driver
SCSI subsystem initialized
libata version 2.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 8000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:05:08.2[B] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[d900e000-d900e7ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:05:0b.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
ohci1394: fw-host1: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[d900d000-d900d7ff] Max Packet=[2048] IR/IT contexts=[4/8]
PCI: Bridge: 0000:00:09.0
IO window: 6000-afff
MEM window: d8000000-d9ffffff
PREFETCH window: da100000-da1fffff
PCI: Bridge: 0000:00:0b.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
IO window: disabled.
MEM window: d0000000-d7ffffff
PREFETCH window: c0000000-cfffffff
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
Coda Kernel/Venus communications, v6.0.0, coda@cs.cmu.edu
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.27 [Flags: R/O].
io scheduler noop registered
io scheduler cfq registered (default)
PCI: Linking AER extended capability on 0000:00:0b.0
PCI: Linking AER extended capability on 0000:00:0c.0
PCI: Linking AER extended capability on 0000:00:0d.0
PCI: Linking AER extended capability on 0000:00:0e.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
Allocate Port Service[0000:00:0b.0:pcie03]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
Allocate Port Service[0000:00:0d.0:pcie03]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Allocate Port Service[0000:00:0e.0:pcie03]
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
nvidiafb: Device ID: 10de0141
nvidiafb: CRTC0 analog found
nvidiafb: CRTC1 analog found
nvidiafb: EDID found from BUS2
nvidiafb: CRTC 0 appears to have a CRT attached
nvidiafb: Using CRT on CRTC 0
nvidiafb: MTRR set to ON
Console: switching to colour frame buffer device 160x66
nvidiafb: PCI nVidia NV14 framebuffer (64MB @ 0xC0000000)
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
Using specific hotkey driver
lp: driver loaded but no devices found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using monotonic_clock().
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:05:0c.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
skge 1.9 addr 0xd9008000 irq 17 chip Yukon-Lite rev 9
skge eth0: addr 00:15:f2:20:e6:69
Marvell 88E1101: Registered new driver
Davicom DM9161E: Registered new driver
Davicom DM9131: Registered new driver
Cicada Cis8204: Registered new driver
Cicada Cis8201: Registered new driver
LXT970: Registered new driver
LXT971: Registered new driver
QS6612: Registered new driver
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.59.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:0a.0 to 64
forcedeth: using HIGHDMA
eth1: forcedeth.c: subsystem: 01043:8141 bound to 0000:00:0a.0
Linux Tulip driver version 1.1.14 (May 11, 2002)
ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
tulip0: MII transceiver #1 config 3100 status 7829 advertising 01e1.
eth2: Lite-On 82c168 PNIC rev 32 at Port 0x8800, 00:A0:CC:21:89:0C, IRQ 17.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
ieee1394: The root node is not cycle master capable; selecting a new root node and resetting...
hda: WDC WD2000JB-32EVA0, ATA DISK drive
ieee1394: Host added: ID:BUS[1-00:1023] GUID[0011d80000738f5d]
hdb: _NEC DVD_RW ND-3540A, ATAPI CD/DVD-ROM drive
ieee1394: Host added: ID:BUS[0-01:1023] GUID[00023c014100f4bf]
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: WDC WD2000JB-00FUA0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
HPT374: IDE controller at PCI slot 0000:05:06.0
ACPI: PCI Interrupt 0000:05:06.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
HPT374: chipset revision 7
HPT374: DPLL base: 48 MHz, f_CNT: 148, assuming 33 MHz PCI
HPT374: using 66 MHz DPLL clock
HPT374: 100% native mode on irq 16
ide2: BM-DMA at 0x7000-0x7007, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0x7008-0x700f, BIOS settings: hdg:pio, hdh:pio
ACPI: PCI Interrupt 0000:05:06.1[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
HPT374: no clock data saved by BIOS
HPT374: DPLL base: 48 MHz, f_CNT: 123, assuming 33 MHz PCI
HPT374: using 66 MHz DPLL clock
ide4: BM-DMA at 0x8400-0x8407, BIOS settings: hdi:DMA, hdj:pio
ide5: BM-DMA at 0x8408-0x840f, BIOS settings: hdk:pio, hdl:pio
Probing IDE interface ide2...
hde: WDC WD2500JB-00FUA0, ATA DISK drive
ide2 at 0x6000-0x6007,0x6402 on irq 16
Probing IDE interface ide3...
Probing IDE interface ide4...
hdi: ST3300831A, ATA DISK drive
ide4 at 0x7400-0x7407,0x7802 on irq 16
Probing IDE interface ide5...
hda: max request size: 512KiB
hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 >
hdc: max request size: 512KiB
hdc: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100)
hdc: cache flushes supported
hdc: hdc1 hdc2 < hdc5 hdc6 hdc7 hdc8 hdc9 >
hde: max request size: 512KiB
hde: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
hde: cache flushes supported
hde: hde1
hdi: max request size: 512KiB
hdi: 586072368 sectors (300069 MB) w/8192KiB Cache, CHS=36481/255/63, UDMA(100)
hdi: cache flushes supported
hdi: hdi1
hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
RocketRAID 3xxx SATA Controller driver v1.0 (060426)
sata_sil 0000:05:0a.0: version 2.0
ACPI: PCI Interrupt 0000:05:0a.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
sata_sil 0000:05:0a.0: Applying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xFFFFC200100BA080 ctl 0xFFFFC200100BA08A bmdma 0xFFFFC200100BA000 irq 19
ata2: SATA max UDMA/100 cmd 0xFFFFC200100BA0C0 ctl 0xFFFFC200100BA0CA bmdma 0xFFFFC200100BA008 irq 19
ata3: SATA max UDMA/100 cmd 0xFFFFC200100BA280 ctl 0xFFFFC200100BA28A bmdma 0xFFFFC200100BA200 irq 19
ata4: SATA max UDMA/100 cmd 0xFFFFC200100BA2C0 ctl 0xFFFFC200100BA2CA bmdma 0xFFFFC200100BA208 irq 19
scsi0 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/100
scsi1 : sata_sil
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/100
scsi2 : sata_sil
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata3.00: ata3: dev 0 multi count 16
ata3.00: configured for UDMA/100
scsi3 : sata_sil
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata4.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata4.00: ata4: dev 0 multi count 16
ata4.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:0:0: Attached scsi disk sdb
sd 1:0:0:0: Attached scsi generic sg1 type 0
scsi 2:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 2:0:0:0: Attached scsi disk sdc
sd 2:0:0:0: Attached scsi generic sg2 type 0
scsi 3:0:0:0: Direct-Access ATA ST3250823AS 3.02 PQ: 0 ANSI: 5
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 3:0:0:0: Attached scsi disk sdd
sd 3:0:0:0: Attached scsi generic sg3 type 0
sata_nv 0000:00:07.0: version 3.3
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 22 (level, low) -> IRQ 22
sata_nv 0000:00:07.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:07.0 to 64
ata5: SATA max UDMA/133 cmd 0xFFFFC200100BC480 ctl 0xFFFFC200100BC4A0 bmdma 0xD800 irq 22
ata6: SATA max UDMA/133 cmd 0xFFFFC200100BC580 ctl 0xFFFFC200100BC5A0 bmdma 0xD808 irq 22
scsi4 : sata_nv
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-7, max UDMA/133, 586072368 sectors: LBA48 NCQ (depth 31/32)
ata5.00: ata5: dev 0 multi count 1
ata5.00: configured for UDMA/133
scsi5 : sata_nv
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 31/32)
ata6.00: ata6: dev 0 multi count 1
ata6.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access ATA ST3300622AS 3.AA PQ: 0 ANSI: 5
ata5: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sde: 586072368 512-byte hdwr sectors (300069 MB)
sde: Write Protect is off
sde: Mode Sense: 00 3a 00 00
SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sde: 586072368 512-byte hdwr sectors (300069 MB)
sde: Write Protect is off
sde: Mode Sense: 00 3a 00 00
SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1 sde2
sd 4:0:0:0: Attached scsi disk sde
sd 4:0:0:0: Attached scsi generic sg4 type 0
scsi 5:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
ata6: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sdf: 488397168 512-byte hdwr sectors (250059 MB)
sdf: Write Protect is off
sdf: Mode Sense: 00 3a 00 00
SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdf: 488397168 512-byte hdwr sectors (250059 MB)
sdf: Write Protect is off
sdf: Mode Sense: 00 3a 00 00
SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdf: sdf1
sd 5:0:0:0: Attached scsi disk sdf
sd 5:0:0:0: Attached scsi generic sg5 type 0
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:08.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata7: SATA max UDMA/133 cmd 0xFFFFC200100BE480 ctl 0xFFFFC200100BE4A0 bmdma 0xC400 irq 21
ata8: SATA max UDMA/133 cmd 0xFFFFC200100BE580 ctl 0xFFFFC200100BE5A0 bmdma 0xC408 irq 21
scsi6 : sata_nv
ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata7.00: ATA-7, max UDMA/133, 586072368 sectors: LBA48 NCQ (depth 31/32)
ata7.00: ata7: dev 0 multi count 1
ata7.00: configured for UDMA/133
scsi7 : sata_nv
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata8.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 31/32)
ata8.00: ata8: dev 0 multi count 1
ata8.00: configured for UDMA/133
scsi 6:0:0:0: Direct-Access ATA ST3300622AS 3.AA PQ: 0 ANSI: 5
ata7: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sdg: 586072368 512-byte hdwr sectors (300069 MB)
sdg: Write Protect is off
sdg: Mode Sense: 00 3a 00 00
SCSI device sdg: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdg: 586072368 512-byte hdwr sectors (300069 MB)
sdg: Write Protect is off
sdg: Mode Sense: 00 3a 00 00
SCSI device sdg: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdg: sdg1 sdg2
sd 6:0:0:0: Attached scsi disk sdg
sd 6:0:0:0: Attached scsi generic sg6 type 0
scsi 7:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
ata8: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sdh: 488397168 512-byte hdwr sectors (250059 MB)
sdh: Write Protect is off
sdh: Mode Sense: 00 3a 00 00
SCSI device sdh: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdh: 488397168 512-byte hdwr sectors (250059 MB)
sdh: Write Protect is off
sdh: Mode Sense: 00 3a 00 00
SCSI device sdh: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdh: sdh1
sd 7:0:0:0: Attached scsi disk sdh
sd 7:0:0:0: Attached scsi generic sg7 type 0
video1394: Installed video1394 module
ieee1394: raw1394: /dev/raw1394 device initialized
WARNING: The dv1394 driver is unsupported and will be removed from Linux soon. Use raw1394 instead.
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 20, io mem 0xfeb00000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.20-rc1-mm1 ehci_hcd
usb usb1: SerialNumber: 0000:00:02.1
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 23, io mem 0xda004000
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.20-rc1-mm1 ohci_hcd
usb usb2: SerialNumber: 0000:00:02.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input2
input: PC Speaker as /class/input/input3
logips2pp: Detected unknown logitech mouse model 1
input: ImPS/2 Logitech Wheel Mouse as /class/input/input4
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int64x1 2227 MB/s
raid6: int64x2 3021 MB/s
raid6: int64x4 2868 MB/s
raid6: int64x8 1996 MB/s
raid6: sse2x1 2547 MB/s
raid6: sse2x2 3671 MB/s
raid6: sse2x4 4130 MB/s
raid6: using algorithm sse2x4 (4130 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: automatically using best checksumming function: generic_sse
generic_sse: 7706.400 MB/sec
raid5: using function: generic_sse (7706.400 MB/sec)
nf_conntrack version 0.5.0 (8192 buckets, 65536 max)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
NET: Registered protocol family 8
NET: Registered protocol family 20
powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ processors (version 2.00.00)
powernow-k8: 0 : fid 0x10 (2400 MHz), vid 0x8
powernow-k8: 1 : fid 0xe (2200 MHz), vid 0xa
powernow-k8: 2 : fid 0xc (2000 MHz), vid 0xc
powernow-k8: 3 : fid 0xa (1800 MHz), vid 0xe
powernow-k8: 4 : fid 0x2 (1000 MHz), vid 0x12
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdh1 ...
md: adding sdh1 ...
md: adding sdg1 ...
md: adding sdf1 ...
md: adding sde1 ...
md: adding sdd1 ...
md: adding sdc1 ...
md: adding sdb1 ...
md: adding sda1 ...
md: hdc9 has different UUID to sdh1
md: hdc8 has different UUID to sdh1
md: hdc7 has different UUID to sdh1
md: hdc6 has different UUID to sdh1
md: hdc5 has different UUID to sdh1
md: hda9 has different UUID to sdh1
md: hda8 has different UUID to sdh1
md: hda7 has different UUID to sdh1
md: hda6 has different UUID to sdh1
md: hda5 has different UUID to sdh1
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: bind<sdc1>
md: bind<sdd1>
md: bind<sde1>
md: bind<sdf1>
md: bind<sdg1>
md: bind<sdh1>
md: running: <sdh1><sdg1><sdf1><sde1><sdd1><sdc1><sdb1><sda1>
raid5: device sdh1 operational as raid disk 1
raid5: device sdg1 operational as raid disk 0
raid5: device sdf1 operational as raid disk 5
raid5: device sde1 operational as raid disk 6
raid5: device sdd1 operational as raid disk 7
raid5: device sdc1 operational as raid disk 3
raid5: device sdb1 operational as raid disk 2
raid5: device sda1 operational as raid disk 4
raid5: allocated 8462kB for md0
raid5: raid level 6 set md0 active with 8 out of 8 devices, algorithm 2
RAID5 conf printout:
--- rd:8 wd:8
disk 0, o:1, dev:sdg1
disk 1, o:1, dev:sdh1
disk 2, o:1, dev:sdb1
disk 3, o:1, dev:sdc1
disk 4, o:1, dev:sda1
disk 5, o:1, dev:sdf1
disk 6, o:1, dev:sde1
disk 7, o:1, dev:sdd1
md0: bitmap initialized from disk: read 15/15 pages, set 1 bits, status: 0
created bitmap (233 pages) for device md0
md: super_written gets error=-5, uptodate=0
raid5: Disk failure on sde1, disabling device. Operation continuing on 7 devices
md: super_written gets error=-5, uptodate=0
raid5: Disk failure on sdg1, disabling device. Operation continuing on 6 devices
md: super_written gets error=-5, uptodate=0
raid5: Disk failure on sdf1, disabling device. Operation continuing on 5 devices
md: super_written gets error=-5, uptodate=0
raid5: Disk failure on sdc1, disabling device. Operation continuing on 4 devices
md: super_written gets error=-5, uptodate=0
raid5: Disk failure on sdb1, disabling device. Operation continuing on 3 devices
md: super_written gets error=-5, uptodate=0
raid5: Disk failure on sdh1, disabling device. Operation continuing on 2 devices
md: super_written gets error=-5, uptodate=0
raid5: Disk failure on sdd1, disabling device. Operation continuing on 1 devices
md: super_written gets error=-5, uptodate=0
raid5: Disk failure on sda1, disabling device. Operation continuing on 0 devices
md: considering hdc9 ...
md: adding hdc9 ...
md: hdc8 has different UUID to hdc9
md: hdc7 has different UUID to hdc9
md: hdc6 has different UUID to hdc9
md: hdc5 has different UUID to hdc9
md: adding hda9 ...
md: hda8 has different UUID to hdc9
md: hda7 has different UUID to hdc9
md: hda6 has different UUID to hdc9
RAID5 conf printout:
--- rd:8 wd:0
disk 0, o:0, dev:sdg1
disk 1, o:0, dev:sdh1
disk 2, o:0, dev:sdb1
disk 3, o:0, dev:sdc1
disk 4, o:0, dev:sda1
disk 5, o:0, dev:sdf1
disk 6, o:0, dev:sde1
disk 7, o:0, dev:sdd1
md: hda5 has different UUID to hdc9
md: created md4
md: bind<hda9>
md: bind<hdc9>
md: running: <hdc9><hda9>
raid1: raid set md4 active with 2 out of 2 mirrors
md4: bitmap initialized from disk: read 10/10 pages, set 49 bits, status: 0
created bitmap (156 pages) for device md4
RAID5 conf printout:
--- rd:8 wd:0
disk 0, o:0, dev:sdg1
disk 2, o:0, dev:sdb1
disk 3, o:0, dev:sdc1
disk 4, o:0, dev:sda1
disk 5, o:0, dev:sdf1
disk 6, o:0, dev:sde1
disk 7, o:0, dev:sdd1
RAID5 conf printout:
--- rd:8 wd:0
disk 0, o:0, dev:sdg1
disk 2, o:0, dev:sdb1
disk 3, o:0, dev:sdc1
disk 4, o:0, dev:sda1
disk 5, o:0, dev:sdf1
disk 6, o:0, dev:sde1
disk 7, o:0, dev:sdd1
md: considering hdc8 ...
md: adding hdc8 ...
md: hdc7 has different UUID to hdc8
md: hdc6 has different UUID to hdc8
md: hdc5 has different UUID to hdc8
md: adding hda8 ...
md: hda7 has different UUID to hdc8
md: hda6 has different UUID to hdc8
md: hda5 has different UUID to hdc8
md: created md3
md: bind<hda8>
md: bind<hdc8>
md: running: <hdc8><hda8>
raid1: raid set md3 active with 2 out of 2 mirrors
RAID5 conf printout:
--- rd:8 wd:0
disk 2, o:0, dev:sdb1
disk 3, o:0, dev:sdc1
disk 4, o:0, dev:sda1
disk 5, o:0, dev:sdf1
disk 6, o:0, dev:sde1
disk 7, o:0, dev:sdd1
RAID5 conf printout:
--- rd:8 wd:0
disk 2, o:0, dev:sdb1
disk 3, o:0, dev:sdc1
disk 4, o:0, dev:sda1
disk 5, o:0, dev:sdf1
disk 6, o:0, dev:sde1
disk 7, o:0, dev:sdd1
RAID5 conf printout:
--- rd:8 wd:0
disk 2, o:0, dev:sdb1
disk 3, o:0, dev:sdc1
disk 4, o:0, dev:sda1
disk 6, o:0, dev:sde1
disk 7, o:0, dev:sdd1
RAID5 conf printout:
--- rd:8 wd:0
disk 2, o:0, dev:sdb1
md3: bitmap initialized from disk: read 8/8 pages, set 6 bits, status: 0
created bitmap (123 pages) for device md3
disk 3, o:0, dev:sdc1
disk 4, o:0, dev:sda1
disk 6, o:0, dev:sde1
disk 7, o:0, dev:sdd1
RAID5 conf printout:
--- rd:8 wd:0
disk 2, o:0, dev:sdb1
disk 3, o:0, dev:sdc1
disk 4, o:0, dev:sda1
disk 7, o:0, dev:sdd1
RAID5 conf printout:
--- rd:8 wd:0
disk 2, o:0, dev:sdb1
disk 3, o:0, dev:sdc1
disk 4, o:0, dev:sda1
disk 7, o:0, dev:sdd1
md: considering hdc7 ...
md: adding hdc7 ...
md: hdc6 has different UUID to hdc7
md: hdc5 has different UUID to hdc7
md: adding hda7 ...
md: hda6 has different UUID to hdc7
md: hda5 has different UUID to hdc7
md: created md2
md: bind<hda7>
md: bind<hdc7>
md: running: <hdc7><hda7>
raid1: raid set md2 active with 2 out of 2 mirrors
RAID5 conf printout:
--- rd:8 wd:0
disk 2, o:0, dev:sdb1
disk 3, o:0, dev:sdc1
disk 4, o:0, dev:sda1
RAID5 conf printout:
--- rd:8 wd:0
disk 2, o:0, dev:sdb1
disk 3, o:0, dev:sdc1
disk 4, o:0, dev:sda1
RAID5 conf printout:
--- rd:8 wd:0
disk 2, o:0, dev:sdb1
disk 4, o:0, dev:sda1
RAID5 conf printout:
md2: bitmap initialized from disk: read 8/8 pages, set 87 bits, status: 0
created bitmap (123 pages) for device md2
--- rd:8 wd:0
disk 2, o:0, dev:sdb1
disk 4, o:0, dev:sda1
RAID5 conf printout:
--- rd:8 wd:0
disk 4, o:0, dev:sda1
RAID5 conf printout:
--- rd:8 wd:0
disk 4, o:0, dev:sda1
md: considering hdc6 ...
md: adding hdc6 ...
md: hdc5 has different UUID to hdc6
md: adding hda6 ...
md: hda5 has different UUID to hdc6
md: created md1
md: bind<hda6>
md: bind<hdc6>
md: running: <hdc6><hda6>
raid1: raid set md1 active with 2 out of 2 mirrors
RAID5 conf printout:
--- rd:8 wd:0
md1: bitmap initialized from disk: read 12/12 pages, set 76 bits, status: 0
created bitmap (184 pages) for device md1
md: considering hdc5 ...
md: adding hdc5 ...
md: adding hda5 ...
md: created md5
md: bind<hda5>
md: bind<hdc5>
md: running: <hdc5><hda5>
raid1: raid set md5 active with 2 out of 2 mirrors
md5: bitmap initialized from disk: read 9/9 pages, set 0 bits, status: 0
created bitmap (129 pages) for device md5
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 284k freed
Adding 4200888k swap on /dev/md5. Priority:-1 extents:1 across:4200888k
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md2, internal journal
i2c_adapter i2c-3: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-4: nForce2 SMBus adapter at 0x4c40
it87: Found IT8712F chip at 0x290, revision 7
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
it87-isa 9191-0290: Detected broken BIOS defaults, disabling PWM interface
ACPI: PCI Interrupt 0000:05:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
Installing spdif_bug patch: Audigy 2 ZS [2001]
Buffer I/O error on device md0, logical block 0
Buffer I/O error on device md0, logical block 1
Buffer I/O error on device md0, logical block 2
Buffer I/O error on device md0, logical block 3
Buffer I/O error on device md0, logical block 4
Buffer I/O error on device md0, logical block 5
Buffer I/O error on device md0, logical block 6
Buffer I/O error on device md0, logical block 7
Buffer I/O error on device md0, logical block 8
Buffer I/O error on device md0, logical block 9
Reducing readahead size to 256K
EXT3-fs: unable to read superblock
Personalities : [linear] [raid0] [raid1] [raid6] [raid5] [raid4]
md5 : active raid1 hdc5[1] hda5[0]
4200896 blocks [2/2] [UU]
bitmap: 0/129 pages [0KB], 16KB chunk
md1 : active raid1 hdc6[0] hda6[1]
6008192 blocks [2/2] [UU]
bitmap: 0/184 pages [0KB], 16KB chunk
md2 : active raid1 hdc7[0] hda7[1]
8008256 blocks [2/2] [UU]
bitmap: 0/123 pages [0KB], 32KB chunk
md3 : active raid1 hdc8[0] hda8[1]
8008256 blocks [2/2] [UU]
bitmap: 0/123 pages [0KB], 32KB chunk
md4 : active raid1 hdc9[0] hda9[1]
162834688 blocks [2/2] [UU]
bitmap: 0/156 pages [0KB], 512KB chunk
md0 : active raid6 sdh1[1] sdg1[0] sdf1[5] sde1[6] sdd1[7] sdc1[3] sdb1[2] sda1[4]
1465175424 blocks level 6, 64k chunk, algorithm 2 [8/8] [UUUUUUUU]
bitmap: 0/233 pages [0KB], 512KB chunk
unused devices: <none>
/dev/md0:
Version : 00.90.03
Creation Time : Fri Feb 3 19:52:27 2006
Raid Level : raid6
Array Size : 1465175424 (1397.30 GiB 1500.34 GB)
Device Size : 244195904 (232.88 GiB 250.06 GB)
Raid Devices : 8
Total Devices : 8
Preferred Minor : 0
Persistence : Superblock is persistent
Intent Bitmap : Internal
Update Time : Fri Dec 15 20:14:55 2006
State : active
Active Devices : 8
Working Devices : 8
Failed Devices : 0
Spare Devices : 0
Chunk Size : 64K
UUID : 128dc711:3f60812f:79b28619:8d0aa46d
Events : 0.55004
Number Major Minor RaidDevice State
0 8 97 0 active sync /dev/sdg1
1 8 113 1 active sync /dev/sdh1
2 8 17 2 active sync /dev/sdb1
3 8 33 3 active sync /dev/sdc1
4 8 1 4 active sync /dev/sda1
5 8 81 5 active sync /dev/sdf1
6 8 65 6 active sync /dev/sde1
7 8 49 7 active sync /dev/sdd1
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.20-rc1-mm1
# Fri Dec 15 19:57:58 2006
#
CONFIG_X86_64=y
CONFIG_64BIT=y
CONFIG_X86=y
CONFIG_ZONE_DMA32=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_CMPXCHG=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_DMI=y
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SWAP_PREFETCH=y
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_CPUSETS is not set
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
CONFIG_UID16=y
# CONFIG_SYSCTL_SYSCALL is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
# CONFIG_VM_EVENT_COUNTERS is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
#
# Block layer
#
CONFIG_BLOCK=y
# CONFIG_BLK_DEV_IO_TRACE is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
# CONFIG_IOSCHED_AS is not set
# CONFIG_IOSCHED_DEADLINE is not set
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_VSMP is not set
CONFIG_MK8=y
# CONFIG_MPSC is not set
# CONFIG_MCORE2 is not set
# CONFIG_GENERIC_CPU is not set
CONFIG_X86_L1_CACHE_BYTES=64
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_INTERNODE_CACHE_BYTES=64
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
# CONFIG_MICROCODE is not set
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_MTRR=y
CONFIG_SMP=y
# CONFIG_SCHED_SMT is not set
CONFIG_SCHED_MC=y
# CONFIG_PREEMPT_NONE is not set
CONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT is not set
CONFIG_PREEMPT_BKL=y
# CONFIG_NUMA is not set
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_RESOURCES_64BIT=y
CONFIG_ZONE_DMA_FLAG=1
CONFIG_ADAPTIVE_READAHEAD=y
CONFIG_NR_CPUS=2
# CONFIG_HOTPLUG_CPU is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_IOMMU=y
CONFIG_CALGARY_IOMMU=y
CONFIG_CALGARY_IOMMU_ENABLED_BY_DEFAULT=y
CONFIG_SWIOTLB=y
CONFIG_X86_MCE=y
# CONFIG_X86_MCE_INTEL is not set
CONFIG_X86_MCE_AMD=y
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x100000
CONFIG_SECCOMP=y
# CONFIG_CC_STACKPROTECTOR is not set
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
CONFIG_HZ_300=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=300
CONFIG_REORDER=y
CONFIG_K8_NB=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_ISA_DMA_API=y
CONFIG_GENERIC_PENDING_IRQ=y
#
# Power management options
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
# CONFIG_PM_SYSFS_DEPRECATED is not set
#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_AC=y
# CONFIG_ACPI_BATTERY is not set
CONFIG_ACPI_BUTTON=y
# CONFIG_ACPI_VIDEO is not set
CONFIG_ACPI_HOTKEY=y
CONFIG_ACPI_FAN=m
# CONFIG_ACPI_DOCK is not set
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=m
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_IBM is not set
# CONFIG_ACPI_TOSHIBA is not set
# CONFIG_ACPI_SONY is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
# CONFIG_ACPI_CONTAINER is not set
# CONFIG_ACPI_SBS is not set
#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=y
# CONFIG_CPU_FREQ_STAT_DETAILS is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
# CONFIG_CPU_FREQ_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
#
# CPUFreq processor drivers
#
CONFIG_X86_POWERNOW_K8=y
CONFIG_X86_POWERNOW_K8_ACPI=y
# CONFIG_X86_SPEEDSTEP_CENTRINO is not set
CONFIG_X86_ACPI_CPUFREQ=m
#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
# CONFIG_X86_P4_CLOCKMOD is not set
# CONFIG_X86_SPEEDSTEP_LIB is not set
#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
# CONFIG_PCI_DOMAINS is not set
CONFIG_PCIEPORTBUS=y
CONFIG_PCIEAER=y
# CONFIG_PCI_MSI is not set
# CONFIG_PCI_DEBUG is not set
CONFIG_HT_IRQ=y
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
CONFIG_IA32_EMULATION=y
CONFIG_IA32_AOUT=y
CONFIG_COMPAT=y
CONFIG_SYSVIPC_COMPAT=y
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_NET_KEY=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_MULTIPATH=y
# CONFIG_IP_ROUTE_MULTIPATH_CACHED is not set
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=y
CONFIG_NET_IPGRE=y
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=y
CONFIG_INET_ESP=y
CONFIG_INET_IPCOMP=y
CONFIG_INET_XFRM_TUNNEL=y
CONFIG_INET_TUNNEL=y
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
#
# IP: Virtual Server Configuration
#
CONFIG_IP_VS=m
# CONFIG_IP_VS_DEBUG is not set
CONFIG_IP_VS_TAB_BITS=12
#
# IPVS transport protocol load balancing support
#
CONFIG_IP_VS_PROTO_TCP=y
CONFIG_IP_VS_PROTO_UDP=y
CONFIG_IP_VS_PROTO_ESP=y
CONFIG_IP_VS_PROTO_AH=y
#
# IPVS scheduler
#
CONFIG_IP_VS_RR=m
CONFIG_IP_VS_WRR=m
CONFIG_IP_VS_LC=m
CONFIG_IP_VS_WLC=m
CONFIG_IP_VS_LBLC=m
CONFIG_IP_VS_LBLCR=m
CONFIG_IP_VS_DH=m
CONFIG_IP_VS_SH=m
CONFIG_IP_VS_SED=m
CONFIG_IP_VS_NQ=m
#
# IPVS application helper
#
CONFIG_IP_VS_FTP=m
CONFIG_IPV6=y
CONFIG_IPV6_PRIVACY=y
# CONFIG_IPV6_ROUTER_PREF is not set
CONFIG_INET6_AH=y
CONFIG_INET6_ESP=y
CONFIG_INET6_IPCOMP=y
# CONFIG_IPV6_MIP6 is not set
CONFIG_INET6_XFRM_TUNNEL=y
CONFIG_INET6_TUNNEL=y
CONFIG_INET6_XFRM_MODE_TRANSPORT=y
CONFIG_INET6_XFRM_MODE_TUNNEL=y
CONFIG_INET6_XFRM_MODE_BEET=y
# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
CONFIG_IPV6_SIT=y
CONFIG_IPV6_TUNNEL=y
# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETWORK_SECMARK is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
#
# Core Netfilter Configuration
#
# CONFIG_NETFILTER_NETLINK is not set
CONFIG_NF_CONNTRACK_ENABLED=y
CONFIG_NF_CONNTRACK_SUPPORT=y
# CONFIG_IP_NF_CONNTRACK_SUPPORT is not set
CONFIG_NF_CONNTRACK=y
# CONFIG_NF_CT_ACCT is not set
# CONFIG_NF_CONNTRACK_MARK is not set
# CONFIG_NF_CONNTRACK_EVENTS is not set
# CONFIG_NF_CT_PROTO_SCTP is not set
# CONFIG_NF_CONNTRACK_AMANDA is not set
# CONFIG_NF_CONNTRACK_FTP is not set
# CONFIG_NF_CONNTRACK_H323 is not set
# CONFIG_NF_CONNTRACK_IRC is not set
# CONFIG_NF_CONNTRACK_NETBIOS_NS is not set
# CONFIG_NF_CONNTRACK_PPTP is not set
# CONFIG_NF_CONNTRACK_SIP is not set
# CONFIG_NF_CONNTRACK_TFTP is not set
CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
# CONFIG_NETFILTER_XT_TARGET_DSCP is not set
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set
# CONFIG_NETFILTER_XT_TARGET_NOTRACK is not set
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
# CONFIG_NETFILTER_XT_MATCH_CONNTRACK is not set
# CONFIG_NETFILTER_XT_MATCH_DCCP is not set
# CONFIG_NETFILTER_XT_MATCH_DSCP is not set
# CONFIG_NETFILTER_XT_MATCH_ESP is not set
# CONFIG_NETFILTER_XT_MATCH_HELPER is not set
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
# CONFIG_NETFILTER_XT_MATCH_POLICY is not set
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
# CONFIG_NETFILTER_XT_MATCH_QUOTA is not set
CONFIG_NETFILTER_XT_MATCH_REALM=m
CONFIG_NETFILTER_XT_MATCH_SCTP=m
# CONFIG_NETFILTER_XT_MATCH_STATE is not set
# CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set
CONFIG_NETFILTER_XT_MATCH_STRING=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set
#
# IP: Netfilter Configuration
#
# CONFIG_NF_CONNTRACK_IPV4 is not set
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_TTL=m
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
#
# IPv6: Netfilter Configuration (EXPERIMENTAL)
#
# CONFIG_NF_CONNTRACK_IPV6 is not set
# CONFIG_IP6_NF_QUEUE is not set
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_MATCH_OPTS=m
CONFIG_IP6_NF_MATCH_FRAG=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_OWNER=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_HL=m
CONFIG_IP6_NF_RAW=m
#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IP_SCTP=m
# CONFIG_SCTP_DBG_MSG is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
# CONFIG_SCTP_HMAC_NONE is not set
# CONFIG_SCTP_HMAC_SHA1 is not set
CONFIG_SCTP_HMAC_MD5=y
#
# TIPC Configuration (EXPERIMENTAL)
#
# CONFIG_TIPC is not set
CONFIG_ATM=y
CONFIG_ATM_CLIP=y
# CONFIG_ATM_CLIP_NO_ICMP is not set
# CONFIG_ATM_LANE is not set
# CONFIG_ATM_BR2684 is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
CONFIG_NET_SCHED=y
CONFIG_NET_SCH_FIFO=y
CONFIG_NET_SCH_CLK_JIFFIES=y
# CONFIG_NET_SCH_CLK_GETTIMEOFDAY is not set
# CONFIG_NET_SCH_CLK_CPU is not set
#
# Queueing/Scheduling
#
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_HFSC=m
CONFIG_NET_SCH_ATM=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_NETEM=m
CONFIG_NET_SCH_INGRESS=m
#
# Classification
#
CONFIG_NET_CLS=y
# CONFIG_NET_CLS_BASIC is not set
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
# CONFIG_CLS_U32_PERF is not set
# CONFIG_CLS_U32_MARK is not set
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
# CONFIG_NET_EMATCH is not set
# CONFIG_NET_CLS_ACT is not set
CONFIG_NET_CLS_POLICE=y
# CONFIG_NET_CLS_IND is not set
CONFIG_NET_ESTIMATOR=y
#
# Network testing
#
CONFIG_NET_PKTGEN=m
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_IEEE80211 is not set
CONFIG_FIB_RULES=y
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_SYS_HYPERVISOR is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
CONFIG_PARPORT_SERIAL=y
CONFIG_PARPORT_PC_FIFO=y
# CONFIG_PARPORT_PC_SUPERIO is not set
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_AX88796 is not set
CONFIG_PARPORT_1284=y
#
# Plug and Play support
#
# CONFIG_PNP is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=65536
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_BLK_DEV_INITRD=y
CONFIG_CDROM_PKTCDVD=y
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
# CONFIG_ATA_OVER_ETH is not set
#
# Misc devices
#
# CONFIG_IBM_ASM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_MSI_LAPTOP is not set
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_IDE_MAX_HWIFS=12
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=y
# CONFIG_IDE_TASK_IOCTL is not set
#
# IDE chipset support/bugfixes
#
# CONFIG_IDE_GENERIC is not set
# CONFIG_BLK_DEV_CMD640 is not set
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_IDEPCI_SHARE_IRQ is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_GENERIC is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
CONFIG_BLK_DEV_HPT366=y
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_BLK_DEV_TC86C001 is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
# CONFIG_SCSI_SCAN_ASYNC is not set
#
# SCSI Transports
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
#
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
CONFIG_SCSI_HPTIOP=y
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
#
# Serial ATA (prod) and Parallel ATA (experimental) drivers
#
CONFIG_ATA=y
CONFIG_SATA_AHCI=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
CONFIG_SATA_NV=y
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
CONFIG_SATA_SIL=y
CONFIG_SATA_SIL24=y
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
CONFIG_SATA_INTEL_COMBINED=y
CONFIG_SATA_ACPI=y
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
# CONFIG_PATA_PLATFORM is not set
#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_LINEAR=y
CONFIG_MD_RAID0=y
CONFIG_MD_RAID1=y
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=y
# CONFIG_MD_RAID5_RESHAPE is not set
# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
# CONFIG_BLK_DEV_DM is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_SPI is not set
# CONFIG_FUSION_FC is not set
# CONFIG_FUSION_SAS is not set
#
# IEEE 1394 (FireWire) support
#
CONFIG_IEEE1394=y
#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
CONFIG_IEEE1394_OUI_DB=y
CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y
CONFIG_IEEE1394_CONFIG_ROM_IP1394=y
# CONFIG_IEEE1394_EXPORT_FULL_API is not set
#
# Device Drivers
#
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=y
#
# Protocol Drivers
#
CONFIG_IEEE1394_VIDEO1394=y
CONFIG_IEEE1394_SBP2=y
# CONFIG_IEEE1394_ETH1394 is not set
CONFIG_IEEE1394_DV1394=y
CONFIG_IEEE1394_RAWIO=y
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
CONFIG_DUMMY=y
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
#
# ARCnet devices
#
CONFIG_ARCNET=m
CONFIG_ARCNET_1201=m
CONFIG_ARCNET_1051=m
CONFIG_ARCNET_RAW=m
# CONFIG_ARCNET_CAP is not set
CONFIG_ARCNET_COM90xx=m
CONFIG_ARCNET_COM90xxIO=m
CONFIG_ARCNET_RIM_I=m
CONFIG_ARCNET_COM20020=m
CONFIG_ARCNET_COM20020_PCI=m
#
# PHY device support
#
CONFIG_PHYLIB=y
#
# MII PHY device drivers
#
CONFIG_MARVELL_PHY=y
CONFIG_DAVICOM_PHY=y
CONFIG_QSEMI_PHY=y
CONFIG_LXT_PHY=y
CONFIG_CICADA_PHY=y
# CONFIG_VITESSE_PHY is not set
# CONFIG_SMSC_PHY is not set
# CONFIG_BROADCOM_PHY is not set
# CONFIG_FIXED_PHY is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
#
# Tulip family network device support
#
CONFIG_NET_TULIP=y
# CONFIG_DE2104X is not set
CONFIG_TULIP=y
# CONFIG_TULIP_MWI is not set
# CONFIG_TULIP_MMIO is not set
# CONFIG_TULIP_NAPI is not set
# CONFIG_DE4X5 is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_DM9102 is not set
# CONFIG_ULI526X is not set
# CONFIG_HP100 is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_B44 is not set
CONFIG_FORCEDETH=y
CONFIG_FORCEDETH_NAPI=y
# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
CONFIG_SKGE=y
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_CHELSIO_T1 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# ATM drivers
#
# CONFIG_ATM_DUMMY is not set
# CONFIG_ATM_TCP is not set
# CONFIG_ATM_LANAI is not set
# CONFIG_ATM_ENI is not set
# CONFIG_ATM_FIRESTREAM is not set
# CONFIG_ATM_ZATM is not set
# CONFIG_ATM_IDT77252 is not set
# CONFIG_ATM_AMBASSADOR is not set
# CONFIG_ATM_HORIZON is not set
# CONFIG_ATM_IA is not set
# CONFIG_ATM_FORE200E_MAYBE is not set
# CONFIG_ATM_HE is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1600
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=1200
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=y
# CONFIG_INPUT_UINPUT is not set
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_NOZOMI is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
CONFIG_SERIAL_8250_RSA=y
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_PRINTER=y
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
#
# Watchdog Device Drivers
#
CONFIG_SOFT_WATCHDOG=m
CONFIG_ACQUIRE_WDT=m
CONFIG_ADVANTECH_WDT=m
CONFIG_ALIM1535_WDT=m
CONFIG_ALIM7101_WDT=m
CONFIG_SC520_WDT=m
CONFIG_EUROTECH_WDT=m
CONFIG_IB700_WDT=m
# CONFIG_IBMASR is not set
CONFIG_WAFER_WDT=m
# CONFIG_I6300ESB_WDT is not set
CONFIG_I8XX_TCO=m
# CONFIG_ITCO_WDT is not set
CONFIG_SC1200_WDT=m
# CONFIG_PC87413_WDT is not set
CONFIG_60XX_WDT=m
# CONFIG_SBC8360_WDT is not set
CONFIG_CPU5_WDT=m
# CONFIG_SMSC37B787_WDT is not set
CONFIG_W83627HF_WDT=m
# CONFIG_W83697HF_WDT is not set
CONFIG_W83877F_WDT=m
# CONFIG_W83977F_WDT is not set
CONFIG_MACHZ_WDT=m
# CONFIG_SBC_EPX_C3_WATCHDOG is not set
#
# PCI-based Watchdog Cards
#
CONFIG_PCIPCWATCHDOG=m
CONFIG_WDTPCI=m
CONFIG_WDT_501_PCI=y
#
# USB-based Watchdog Cards
#
CONFIG_USBPCWATCHDOG=m
CONFIG_HW_RANDOM=y
# CONFIG_HW_RANDOM_INTEL is not set
CONFIG_HW_RANDOM_AMD=y
# CONFIG_HW_RANDOM_GEODE is not set
CONFIG_NVRAM=y
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
CONFIG_AGP=y
CONFIG_AGP_AMD64=y
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
# CONFIG_PC8736x_GPIO is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=y
#
# TPM devices
#
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set
#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set
#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_PIIX4 is not set
CONFIG_I2C_ISA=m
CONFIG_I2C_NFORCE2=m
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
CONFIG_SENSORS_EEPROM=m
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
# Hardware Monitoring support
#
CONFIG_HWMON=y
CONFIG_HWMON_VID=m
# CONFIG_SENSORS_ABITUGURU is not set
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ADM1025=m
CONFIG_SENSORS_ADM1026=m
CONFIG_SENSORS_ADM1031=m
CONFIG_SENSORS_ADM9240=m
CONFIG_SENSORS_K8TEMP=y
CONFIG_SENSORS_ASB100=m
CONFIG_SENSORS_ATXP1=m
CONFIG_SENSORS_DS1621=m
CONFIG_SENSORS_F71805F=m
CONFIG_SENSORS_FSCHER=m
CONFIG_SENSORS_FSCPOS=m
CONFIG_SENSORS_GL518SM=m
CONFIG_SENSORS_GL520SM=m
CONFIG_SENSORS_IT87=m
CONFIG_SENSORS_LM63=m
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM77=m
CONFIG_SENSORS_LM78=m
CONFIG_SENSORS_LM80=m
CONFIG_SENSORS_LM83=m
CONFIG_SENSORS_LM85=m
CONFIG_SENSORS_LM87=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_LM92=m
CONFIG_SENSORS_MAX1619=m
CONFIG_SENSORS_PC87360=m
# CONFIG_SENSORS_PC87427 is not set
CONFIG_SENSORS_SIS5595=m
CONFIG_SENSORS_SMSC47M1=m
CONFIG_SENSORS_SMSC47M192=m
CONFIG_SENSORS_SMSC47B397=m
CONFIG_SENSORS_VIA686A=m
# CONFIG_SENSORS_VT1211 is not set
CONFIG_SENSORS_VT8231=m
CONFIG_SENSORS_W83781D=m
CONFIG_SENSORS_W83791D=m
CONFIG_SENSORS_W83792D=m
# CONFIG_SENSORS_W83793 is not set
CONFIG_SENSORS_W83L785TS=m
CONFIG_SENSORS_W83627HF=m
CONFIG_SENSORS_W83627EHF=m
# CONFIG_SENSORS_HDAPS is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
# CONFIG_USB_DABUSB is not set
#
# Graphics support
#
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_BACKLIGHT_CLASS_DEVICE=y
CONFIG_BACKLIGHT_DEVICE=y
CONFIG_LCD_CLASS_DEVICE=m
CONFIG_LCD_DEVICE=y
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
# CONFIG_FB_DDC is not set
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
# CONFIG_FB_TILEBLITTING is not set
#
# Frambuffer hardware drivers
#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_VESA is not set
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_NVIDIA=y
CONFIG_FB_NVIDIA_I2C=y
CONFIG_FB_NVIDIA_BACKLIGHT=y
# CONFIG_FB_RIVA is not set
# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VGACON_SOFT_SCROLLBACK is not set
CONFIG_VIDEO_SELECT=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
CONFIG_FONTS=y
# CONFIG_FONT_8x8 is not set
# CONFIG_FONT_8x16 is not set
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_7x14 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
# CONFIG_FONT_MINI_4x6 is not set
# CONFIG_FONT_SUN8x16 is not set
# CONFIG_FONT_SUN12x22 is not set
CONFIG_FONT_10x18=y
#
# Logo configuration
#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
#
# Sound
#
CONFIG_SOUND=m
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
# CONFIG_SND_DYNAMIC_MINORS is not set
# CONFIG_SND_SUPPORT_OLD_API is not set
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
#
# Generic devices
#
CONFIG_SND_AC97_CODEC=m
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_MTS64 is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
#
# PCI devices
#
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
CONFIG_SND_EMU10K1=m
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_HDA_INTEL is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_AC97_POWER_SAVE is not set
#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set
#
# SoC audio support
#
# CONFIG_SND_SOC is not set
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
CONFIG_AC97_BUS=m
#
# HID Devices
#
CONFIG_HID=y
#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_BANDWIDTH=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_MULTITHREAD_PROBE is not set
# CONFIG_USB_OTG is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
#
# USB Device Class drivers
#
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=y
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# may also be needed; see USB_STORAGE Help for more information
#
# CONFIG_USB_STORAGE is not set
# CONFIG_USB_LIBUSUAL is not set
#
# USB Input Devices
#
# CONFIG_USB_HID is not set
#
# USB HID Boot Protocol drivers
#
CONFIG_USB_KBD=m
CONFIG_USB_MOUSE=m
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_ACECAD is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_TOUCHSCREEN is not set
# CONFIG_USB_YEALINK is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
# CONFIG_USB_ATI_REMOTE2 is not set
# CONFIG_USB_KEYSPAN_REMOTE is not set
# CONFIG_USB_APPLETOUCH is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_MON is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_TEST is not set
# CONFIG_USB_GOTEMP is not set
#
# USB DSL modem support
#
# CONFIG_USB_ATM is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# LED devices
#
# CONFIG_NEW_LEDS is not set
#
# LED drivers
#
#
# LED Triggers
#
#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set
#
# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
# CONFIG_EDAC is not set
#
# Real Time Clock
#
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
# CONFIG_RTC_DEBUG is not set
#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
#
# RTC drivers
#
CONFIG_RTC_DRV_X1205=m
CONFIG_RTC_DRV_DS1307=m
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_ISL1208 is not set
CONFIG_RTC_DRV_DS1672=m
# CONFIG_RTC_DRV_DS1742 is not set
CONFIG_RTC_DRV_PCF8563=m
# CONFIG_RTC_DRV_PCF8583 is not set
CONFIG_RTC_DRV_RS5C372=m
CONFIG_RTC_DRV_M48T86=m
# CONFIG_RTC_DRV_TEST is not set
# CONFIG_RTC_DRV_V3020 is not set
#
# DMA Engine support
#
# CONFIG_DMA_ENGINE is not set
#
# DMA Clients
#
#
# DMA Devices
#
#
# Auxiliary Display support
#
# CONFIG_KS0108 is not set
#
# Virtualization
#
# CONFIG_KVM is not set
#
# Userspace I/O
#
# CONFIG_UIO is not set
#
# Firmware Drivers
#
# CONFIG_EDD is not set
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISER4_FS is not set
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
# CONFIG_REISERFS_FS_XATTR is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
CONFIG_MINIX_FS=y
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
# CONFIG_DNOTIFY is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=y
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=y
# CONFIG_NTFS_DEBUG is not set
# CONFIG_NTFS_RW is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=y
# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
# CONFIG_9P_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="cp437"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=y
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
#
# Distributed Lock Manager
#
# CONFIG_DLM is not set
#
# Instrumentation Support
#
# CONFIG_PROFILING is not set
# CONFIG_KPROBES is not set
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_PAGE_OWNER is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_LOG_BUF_SHIFT=18
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
CONFIG_FRAME_POINTER=y
CONFIG_UNWIND_INFO=y
# CONFIG_STACK_UNWIND is not set
# CONFIG_PROFILE_LIKELY is not set
# CONFIG_FORCED_INLINING is not set
# CONFIG_DEBUG_SYNCHRO_TEST is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_DEBUG_RODATA is not set
# CONFIG_IOMMU_DEBUG is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_INTEGRITY is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITY_FS_CAPABILITIES is not set
#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=y
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=y
# CONFIG_CRYPTO_LRW is not set
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
# CONFIG_CRYPTO_TWOFISH_X86_64 is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_AES is not set
# CONFIG_CRYPTO_AES_X86_64 is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_TEA is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_ANUBIS is not set
CONFIG_CRYPTO_DEFLATE=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_TEST is not set
#
# Hardware crypto devices
#
#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=y
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
CONFIG_LIBCRC32C=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
CONFIG_IOMAP_COPY=y
--
I'd like to, but there are important world issues that need worrying about.
Debian (Unstable) GNU/Linux 2.6.19-rc5-mm1 2x4826 bogomips load 6.29
the Jack Vance Integral Edition: http://www.integralarchive.org
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: md patches in -mm
2006-12-15 19:21 ` md patches in -mm thunder7
@ 2006-12-15 20:06 ` Andrew Morton
2006-12-15 20:50 ` sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm] Neil Brown
1 sibling, 0 replies; 27+ messages in thread
From: Andrew Morton @ 2006-12-15 20:06 UTC (permalink / raw)
To: Jurriaan; +Cc: Neil Brown, linux-kernel, linux-raid
On Fri, 15 Dec 2006 20:21:46 +0100
thunder7@xs4all.nl wrote:
> From: Neil Brown <neilb@suse.de>
> Date: Wed, Dec 06, 2006 at 06:20:57PM +1100
> > i.e. current -mm is good for 2.6.20 (though I have a few other little
> > things I'll be sending in soon, they aren't related to the raid6
> > problem).
> >
> 2.6.20-rc1-mm1 doesn't boot on my box, due to the fact that e2fsck gives
>
> Buffer I/O error on device /dev/md0, logical block 0
>
> and after that 1,2,3,4,5,6,7,8,9, at which points it complains it can't
> read the superblock. It seems the raid6 problem hasn't gone away
> completely, after all.
Odd. The only md patch in rc1-mm1 is the truly ancient
md-dm-reduce-stack-usage-with-stacked-block-devices.patch
Does 2.6.20-rc1 work?
^ permalink raw reply [flat|nested] 27+ messages in thread
* sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 19:21 ` md patches in -mm thunder7
2006-12-15 20:06 ` Andrew Morton
@ 2006-12-15 20:50 ` Neil Brown
2006-12-15 21:05 ` Andrew Morton
2006-12-15 21:15 ` Rafael J. Wysocki
1 sibling, 2 replies; 27+ messages in thread
From: Neil Brown @ 2006-12-15 20:50 UTC (permalink / raw)
To: Jurriaan; +Cc: Andrew Morton, linux-kernel, linux-raid
On Friday December 15, thunder7@xs4all.nl wrote:
> From: Neil Brown <neilb@suse.de>
> Date: Wed, Dec 06, 2006 at 06:20:57PM +1100
> > i.e. current -mm is good for 2.6.20 (though I have a few other little
> > things I'll be sending in soon, they aren't related to the raid6
> > problem).
> >
> 2.6.20-rc1-mm1 doesn't boot on my box, due to the fact that e2fsck gives
>
> Buffer I/O error on device /dev/md0, logical block 0
>
But before that....
> raid5: device sdh1 operational as raid disk 1
> raid5: device sdg1 operational as raid disk 0
> raid5: device sdf1 operational as raid disk 5
> raid5: device sde1 operational as raid disk 6
> raid5: device sdd1 operational as raid disk 7
> raid5: device sdc1 operational as raid disk 3
> raid5: device sdb1 operational as raid disk 2
> raid5: device sda1 operational as raid disk 4
> raid5: allocated 8462kB for md0
> raid5: raid level 6 set md0 active with 8 out of 8 devices, algorithm 2
> RAID5 conf printout:
> --- rd:8 wd:8
> disk 0, o:1, dev:sdg1
> disk 1, o:1, dev:sdh1
> disk 2, o:1, dev:sdb1
> disk 3, o:1, dev:sdc1
> disk 4, o:1, dev:sda1
> disk 5, o:1, dev:sdf1
> disk 6, o:1, dev:sde1
> disk 7, o:1, dev:sdd1
> md0: bitmap initialized from disk: read 15/15 pages, set 1 bits, status: 0
> created bitmap (233 pages) for device md0
> md: super_written gets error=-5, uptodate=0
> raid5: Disk failure on sde1, disabling device. Operation continuing on 7 devices
> md: super_written gets error=-5, uptodate=0
> raid5: Disk failure on sdg1, disabling device. Operation continuing on 6 devices
> md: super_written gets error=-5, uptodate=0
> raid5: Disk failure on sdf1, disabling device. Operation continuing on 5 devices
> md: super_written gets error=-5, uptodate=0
> raid5: Disk failure on sdc1, disabling device. Operation continuing on 4 devices
> md: super_written gets error=-5, uptodate=0
> raid5: Disk failure on sdb1, disabling device. Operation continuing on 3 devices
> md: super_written gets error=-5, uptodate=0
> raid5: Disk failure on sdh1, disabling device. Operation continuing on 2 devices
> md: super_written gets error=-5, uptodate=0
> raid5: Disk failure on sdd1, disabling device. Operation continuing on 1 devices
> md: super_written gets error=-5, uptodate=0
> raid5: Disk failure on sda1, disabling device. Operation continuing on 0 devices
Oh dear, that array isn't much good any more.!
That is the second report I have had of this with sata drives. This
was raid456, the other was raid1. Two different sata drivers are
involved (sata_nv in this case, sata_uli in the other case).
I think something bad happened in sata land just recently.
The device driver is returning -EIO for a write without printing any messages.
NeilBrown
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 20:50 ` sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm] Neil Brown
@ 2006-12-15 21:05 ` Andrew Morton
2006-12-15 21:18 ` Rafael J. Wysocki
` (2 more replies)
2006-12-15 21:15 ` Rafael J. Wysocki
1 sibling, 3 replies; 27+ messages in thread
From: Andrew Morton @ 2006-12-15 21:05 UTC (permalink / raw)
To: Neil Brown; +Cc: Jurriaan, linux-kernel, linux-raid, Jeff Garzik, Tejun Heo
On Sat, 16 Dec 2006 07:50:01 +1100
Neil Brown <neilb@suse.de> wrote:
> On Friday December 15, thunder7@xs4all.nl wrote:
> > From: Neil Brown <neilb@suse.de>
> > Date: Wed, Dec 06, 2006 at 06:20:57PM +1100
> > > i.e. current -mm is good for 2.6.20 (though I have a few other little
> > > things I'll be sending in soon, they aren't related to the raid6
> > > problem).
> > >
> > 2.6.20-rc1-mm1 doesn't boot on my box, due to the fact that e2fsck gives
> >
> > Buffer I/O error on device /dev/md0, logical block 0
> >
>
> But before that....
> > raid5: device sdh1 operational as raid disk 1
> > raid5: device sdg1 operational as raid disk 0
> > raid5: device sdf1 operational as raid disk 5
> > raid5: device sde1 operational as raid disk 6
> > raid5: device sdd1 operational as raid disk 7
> > raid5: device sdc1 operational as raid disk 3
> > raid5: device sdb1 operational as raid disk 2
> > raid5: device sda1 operational as raid disk 4
> > raid5: allocated 8462kB for md0
> > raid5: raid level 6 set md0 active with 8 out of 8 devices, algorithm 2
> > RAID5 conf printout:
> > --- rd:8 wd:8
> > disk 0, o:1, dev:sdg1
> > disk 1, o:1, dev:sdh1
> > disk 2, o:1, dev:sdb1
> > disk 3, o:1, dev:sdc1
> > disk 4, o:1, dev:sda1
> > disk 5, o:1, dev:sdf1
> > disk 6, o:1, dev:sde1
> > disk 7, o:1, dev:sdd1
> > md0: bitmap initialized from disk: read 15/15 pages, set 1 bits, status: 0
> > created bitmap (233 pages) for device md0
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sde1, disabling device. Operation continuing on 7 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sdg1, disabling device. Operation continuing on 6 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sdf1, disabling device. Operation continuing on 5 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sdc1, disabling device. Operation continuing on 4 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sdb1, disabling device. Operation continuing on 3 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sdh1, disabling device. Operation continuing on 2 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sdd1, disabling device. Operation continuing on 1 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sda1, disabling device. Operation continuing on 0 devices
>
> Oh dear, that array isn't much good any more.!
> That is the second report I have had of this with sata drives. This
> was raid456, the other was raid1. Two different sata drivers are
> involved (sata_nv in this case, sata_uli in the other case).
> I think something bad happened in sata land just recently.
> The device driver is returning -EIO for a write without printing any messages.
>
OK, this is bad. The wheels do appear to have fallen off sata in rc1-mm1.
Jeff, I shall send all the sata patches which I have at you one single time
and I shall then drop the lot. So please don't flub them.
I'll then do a rc1-mm2 without them.
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 20:50 ` sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm] Neil Brown
2006-12-15 21:05 ` Andrew Morton
@ 2006-12-15 21:15 ` Rafael J. Wysocki
2006-12-15 21:49 ` Jeff Garzik
1 sibling, 1 reply; 27+ messages in thread
From: Rafael J. Wysocki @ 2006-12-15 21:15 UTC (permalink / raw)
To: Neil Brown; +Cc: Jurriaan, Andrew Morton, linux-kernel, linux-raid
I don't think it's in -rc1, please see below.
On Friday, 15 December 2006 21:50, Neil Brown wrote:
> On Friday December 15, thunder7@xs4all.nl wrote:
> > From: Neil Brown <neilb@suse.de>
> > Date: Wed, Dec 06, 2006 at 06:20:57PM +1100
> > > i.e. current -mm is good for 2.6.20 (though I have a few other little
> > > things I'll be sending in soon, they aren't related to the raid6
> > > problem).
> > >
> > 2.6.20-rc1-mm1 doesn't boot on my box, due to the fact that e2fsck gives
> >
> > Buffer I/O error on device /dev/md0, logical block 0
> >
>
> But before that....
> > raid5: device sdh1 operational as raid disk 1
> > raid5: device sdg1 operational as raid disk 0
> > raid5: device sdf1 operational as raid disk 5
> > raid5: device sde1 operational as raid disk 6
> > raid5: device sdd1 operational as raid disk 7
> > raid5: device sdc1 operational as raid disk 3
> > raid5: device sdb1 operational as raid disk 2
> > raid5: device sda1 operational as raid disk 4
> > raid5: allocated 8462kB for md0
> > raid5: raid level 6 set md0 active with 8 out of 8 devices, algorithm 2
> > RAID5 conf printout:
> > --- rd:8 wd:8
> > disk 0, o:1, dev:sdg1
> > disk 1, o:1, dev:sdh1
> > disk 2, o:1, dev:sdb1
> > disk 3, o:1, dev:sdc1
> > disk 4, o:1, dev:sda1
> > disk 5, o:1, dev:sdf1
> > disk 6, o:1, dev:sde1
> > disk 7, o:1, dev:sdd1
> > md0: bitmap initialized from disk: read 15/15 pages, set 1 bits, status: 0
> > created bitmap (233 pages) for device md0
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sde1, disabling device. Operation continuing on 7 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sdg1, disabling device. Operation continuing on 6 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sdf1, disabling device. Operation continuing on 5 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sdc1, disabling device. Operation continuing on 4 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sdb1, disabling device. Operation continuing on 3 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sdh1, disabling device. Operation continuing on 2 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sdd1, disabling device. Operation continuing on 1 devices
> > md: super_written gets error=-5, uptodate=0
> > raid5: Disk failure on sda1, disabling device. Operation continuing on 0 devices
>
> Oh dear, that array isn't much good any more.!
> That is the second report I have had of this with sata drives. This
> was raid456, the other was raid1. Two different sata drivers are
> involved (sata_nv in this case, sata_uli in the other case).
The other box is mine and it works just fine with 2.6.20-rc1.
> I think something bad happened in sata land just recently.
Yup. Please see, for example:
http://marc.theaimsgroup.com/?l=linux-kernel&m=116621656432500&w=2
It looks like the breakage is in sata, in the patches that went in after
2.6.19-rc6-mm2 (that one worked for me like charm).
Greetings,
Rafael
--
If you don't have the time to read,
you don't have the time or the tools to write.
- Stephen King
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 21:05 ` Andrew Morton
@ 2006-12-15 21:18 ` Rafael J. Wysocki
2006-12-15 21:39 ` Andrew Morton
2006-12-15 21:48 ` Jeff Garzik
2 siblings, 0 replies; 27+ messages in thread
From: Rafael J. Wysocki @ 2006-12-15 21:18 UTC (permalink / raw)
To: Andrew Morton
Cc: Neil Brown, Jurriaan, linux-kernel, linux-raid, Jeff Garzik, Tejun Heo
On Friday, 15 December 2006 22:05, Andrew Morton wrote:
> On Sat, 16 Dec 2006 07:50:01 +1100
> Neil Brown <neilb@suse.de> wrote:
>
> > On Friday December 15, thunder7@xs4all.nl wrote:
> > > From: Neil Brown <neilb@suse.de>
> > > Date: Wed, Dec 06, 2006 at 06:20:57PM +1100
> > > > i.e. current -mm is good for 2.6.20 (though I have a few other little
> > > > things I'll be sending in soon, they aren't related to the raid6
> > > > problem).
> > > >
> > > 2.6.20-rc1-mm1 doesn't boot on my box, due to the fact that e2fsck gives
> > >
> > > Buffer I/O error on device /dev/md0, logical block 0
> > >
> >
> > But before that....
> > > raid5: device sdh1 operational as raid disk 1
> > > raid5: device sdg1 operational as raid disk 0
> > > raid5: device sdf1 operational as raid disk 5
> > > raid5: device sde1 operational as raid disk 6
> > > raid5: device sdd1 operational as raid disk 7
> > > raid5: device sdc1 operational as raid disk 3
> > > raid5: device sdb1 operational as raid disk 2
> > > raid5: device sda1 operational as raid disk 4
> > > raid5: allocated 8462kB for md0
> > > raid5: raid level 6 set md0 active with 8 out of 8 devices, algorithm 2
> > > RAID5 conf printout:
> > > --- rd:8 wd:8
> > > disk 0, o:1, dev:sdg1
> > > disk 1, o:1, dev:sdh1
> > > disk 2, o:1, dev:sdb1
> > > disk 3, o:1, dev:sdc1
> > > disk 4, o:1, dev:sda1
> > > disk 5, o:1, dev:sdf1
> > > disk 6, o:1, dev:sde1
> > > disk 7, o:1, dev:sdd1
> > > md0: bitmap initialized from disk: read 15/15 pages, set 1 bits, status: 0
> > > created bitmap (233 pages) for device md0
> > > md: super_written gets error=-5, uptodate=0
> > > raid5: Disk failure on sde1, disabling device. Operation continuing on 7 devices
> > > md: super_written gets error=-5, uptodate=0
> > > raid5: Disk failure on sdg1, disabling device. Operation continuing on 6 devices
> > > md: super_written gets error=-5, uptodate=0
> > > raid5: Disk failure on sdf1, disabling device. Operation continuing on 5 devices
> > > md: super_written gets error=-5, uptodate=0
> > > raid5: Disk failure on sdc1, disabling device. Operation continuing on 4 devices
> > > md: super_written gets error=-5, uptodate=0
> > > raid5: Disk failure on sdb1, disabling device. Operation continuing on 3 devices
> > > md: super_written gets error=-5, uptodate=0
> > > raid5: Disk failure on sdh1, disabling device. Operation continuing on 2 devices
> > > md: super_written gets error=-5, uptodate=0
> > > raid5: Disk failure on sdd1, disabling device. Operation continuing on 1 devices
> > > md: super_written gets error=-5, uptodate=0
> > > raid5: Disk failure on sda1, disabling device. Operation continuing on 0 devices
> >
> > Oh dear, that array isn't much good any more.!
> > That is the second report I have had of this with sata drives. This
> > was raid456, the other was raid1. Two different sata drivers are
> > involved (sata_nv in this case, sata_uli in the other case).
> > I think something bad happened in sata land just recently.
> > The device driver is returning -EIO for a write without printing any messages.
> >
>
> OK, this is bad. The wheels do appear to have fallen off sata in rc1-mm1.
I think it's happened in 2.6.19-mm1 already, since that kernel breaks md RAID1
on my box (the sata_uli case above).
Greetings,
Rafael
--
If you don't have the time to read,
you don't have the time or the tools to write.
- Stephen King
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 21:05 ` Andrew Morton
2006-12-15 21:18 ` Rafael J. Wysocki
@ 2006-12-15 21:39 ` Andrew Morton
2006-12-15 21:46 ` Rafael J. Wysocki
` (2 more replies)
2006-12-15 21:48 ` Jeff Garzik
2 siblings, 3 replies; 27+ messages in thread
From: Andrew Morton @ 2006-12-15 21:39 UTC (permalink / raw)
To: Neil Brown, Jurriaan, linux-kernel, linux-raid, Jeff Garzik, Tejun Heo
On Fri, 15 Dec 2006 13:05:52 -0800
Andrew Morton <akpm@osdl.org> wrote:
> Jeff, I shall send all the sata patches which I have at you one single time
> and I shall then drop the lot. So please don't flub them.
>
> I'll then do a rc1-mm2 without them.
hm, this is looking like a lot of work for not much gain. Rafael, are
you able to do a quick chop and tell us whether these:
pci-move-pci_vdevice-from-libata-to-core.patch
pata_cs5530-suspend-resume-support-tweak.patch
ata-fix-platform_device_register_simple-error-check.patch
initializer-entry-defined-twice-in-pata_rz1000.patch
pata_via-suspend-resume-support-fix.patch
sata_nv-add-suspend-resume-support.patch
libata-simulate-report-luns-for-atapi-devices.patch
user-of-the-jiffies-rounding-patch-ata-subsystem.patch
libata-fix-oops-with-sparsemem.patch
sata_nv-fix-kfree-ordering-in-remove.patch
libata-dont-initialize-sg-in-ata_exec_internal-if-dma_none-take-2.patch
pci-quirks-fix-the-festering-mess-that-claims-to-handle-ide-quirks-ide-fix.patch
are innocent?
Thanks.
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 21:39 ` Andrew Morton
@ 2006-12-15 21:46 ` Rafael J. Wysocki
2006-12-15 22:06 ` Alan
2006-12-15 22:22 ` Rafael J. Wysocki
2 siblings, 0 replies; 27+ messages in thread
From: Rafael J. Wysocki @ 2006-12-15 21:46 UTC (permalink / raw)
To: Andrew Morton
Cc: Neil Brown, Jurriaan, linux-kernel, linux-raid, Jeff Garzik, Tejun Heo
On Friday, 15 December 2006 22:39, Andrew Morton wrote:
> On Fri, 15 Dec 2006 13:05:52 -0800
> Andrew Morton <akpm@osdl.org> wrote:
>
> > Jeff, I shall send all the sata patches which I have at you one single time
> > and I shall then drop the lot. So please don't flub them.
> >
> > I'll then do a rc1-mm2 without them.
>
> hm, this is looking like a lot of work for not much gain. Rafael, are
> you able to do a quick chop and tell us whether these:
>
> pci-move-pci_vdevice-from-libata-to-core.patch
> pata_cs5530-suspend-resume-support-tweak.patch
> ata-fix-platform_device_register_simple-error-check.patch
> initializer-entry-defined-twice-in-pata_rz1000.patch
> pata_via-suspend-resume-support-fix.patch
> sata_nv-add-suspend-resume-support.patch
> libata-simulate-report-luns-for-atapi-devices.patch
> user-of-the-jiffies-rounding-patch-ata-subsystem.patch
> libata-fix-oops-with-sparsemem.patch
> sata_nv-fix-kfree-ordering-in-remove.patch
> libata-dont-initialize-sg-in-ata_exec_internal-if-dma_none-take-2.patch
> pci-quirks-fix-the-festering-mess-that-claims-to-handle-ide-quirks-ide-fix.patch
>
> are innocent?
Will do in a while and report back. Stay tuned.
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 21:05 ` Andrew Morton
2006-12-15 21:18 ` Rafael J. Wysocki
2006-12-15 21:39 ` Andrew Morton
@ 2006-12-15 21:48 ` Jeff Garzik
2006-12-16 6:03 ` thunder7
2 siblings, 1 reply; 27+ messages in thread
From: Jeff Garzik @ 2006-12-15 21:48 UTC (permalink / raw)
To: Andrew Morton; +Cc: Neil Brown, Jurriaan, linux-kernel, linux-raid, Tejun Heo
The "Re: Linux 2.6.20-rc1" sub-thread that had Jens and Alistair John
Strachan replying seemed to implicate some core block layer badness.
Jeff
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 21:15 ` Rafael J. Wysocki
@ 2006-12-15 21:49 ` Jeff Garzik
2006-12-15 21:56 ` Rafael J. Wysocki
0 siblings, 1 reply; 27+ messages in thread
From: Jeff Garzik @ 2006-12-15 21:49 UTC (permalink / raw)
To: Rafael J. Wysocki
Cc: Neil Brown, Jurriaan, Andrew Morton, linux-kernel, linux-raid
Rafael J. Wysocki wrote:
> The other box is mine and it works just fine with 2.6.20-rc1.
>
>> I think something bad happened in sata land just recently.
>
> Yup. Please see, for example:
>
> http://marc.theaimsgroup.com/?l=linux-kernel&m=116621656432500&w=2
>
> It looks like the breakage is in sata, in the patches that went in after
> 2.6.19-rc6-mm2 (that one worked for me like charm).
So.... 2.6.20-rc1 works for you?
Jeff
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 21:49 ` Jeff Garzik
@ 2006-12-15 21:56 ` Rafael J. Wysocki
0 siblings, 0 replies; 27+ messages in thread
From: Rafael J. Wysocki @ 2006-12-15 21:56 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Neil Brown, Jurriaan, Andrew Morton, linux-kernel, linux-raid
On Friday, 15 December 2006 22:49, Jeff Garzik wrote:
> Rafael J. Wysocki wrote:
> > The other box is mine and it works just fine with 2.6.20-rc1.
> >
> >> I think something bad happened in sata land just recently.
> >
> > Yup. Please see, for example:
> >
> > http://marc.theaimsgroup.com/?l=linux-kernel&m=116621656432500&w=2
> >
> > It looks like the breakage is in sata, in the patches that went in after
> > 2.6.19-rc6-mm2 (that one worked for me like charm).
>
>
> So.... 2.6.20-rc1 works for you?
Yes.
Greetings,
Rafael
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 22:06 ` Alan
@ 2006-12-15 22:04 ` Rafael J. Wysocki
2006-12-15 22:19 ` Jeff Garzik
1 sibling, 0 replies; 27+ messages in thread
From: Rafael J. Wysocki @ 2006-12-15 22:04 UTC (permalink / raw)
To: Alan
Cc: Andrew Morton, Neil Brown, Jurriaan, linux-kernel, linux-raid,
Jeff Garzik, Tejun Heo
On Friday, 15 December 2006 23:06, Alan wrote:
> On Fri, 15 Dec 2006 13:39:27 -0800
> Andrew Morton <akpm@osdl.org> wrote:
>
> > On Fri, 15 Dec 2006 13:05:52 -0800
> > Andrew Morton <akpm@osdl.org> wrote:
> >
> > > Jeff, I shall send all the sata patches which I have at you one single time
> > > and I shall then drop the lot. So please don't flub them.
> > >
> > > I'll then do a rc1-mm2 without them.
> >
> > hm, this is looking like a lot of work for not much gain. Rafael, are
> > you able to do a quick chop and tell us whether these:
>
> The md one and the long history of reports about parallel I/O causing
> problems sounds a lot more like the kmap stuff you were worried about
> Andrew. I'd be very intereste dto know if it happens on x86_32 built with
> a standard memory split and no highmem....
But my box is a x86_64, so ...
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 21:39 ` Andrew Morton
2006-12-15 21:46 ` Rafael J. Wysocki
@ 2006-12-15 22:06 ` Alan
2006-12-15 22:04 ` Rafael J. Wysocki
2006-12-15 22:19 ` Jeff Garzik
2006-12-15 22:22 ` Rafael J. Wysocki
2 siblings, 2 replies; 27+ messages in thread
From: Alan @ 2006-12-15 22:06 UTC (permalink / raw)
To: Andrew Morton
Cc: Neil Brown, Jurriaan, linux-kernel, linux-raid, Jeff Garzik, Tejun Heo
On Fri, 15 Dec 2006 13:39:27 -0800
Andrew Morton <akpm@osdl.org> wrote:
> On Fri, 15 Dec 2006 13:05:52 -0800
> Andrew Morton <akpm@osdl.org> wrote:
>
> > Jeff, I shall send all the sata patches which I have at you one single time
> > and I shall then drop the lot. So please don't flub them.
> >
> > I'll then do a rc1-mm2 without them.
>
> hm, this is looking like a lot of work for not much gain. Rafael, are
> you able to do a quick chop and tell us whether these:
The md one and the long history of reports about parallel I/O causing
problems sounds a lot more like the kmap stuff you were worried about
Andrew. I'd be very intereste dto know if it happens on x86_32 built with
a standard memory split and no highmem....
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 22:06 ` Alan
2006-12-15 22:04 ` Rafael J. Wysocki
@ 2006-12-15 22:19 ` Jeff Garzik
2006-12-15 22:27 ` Rafael J. Wysocki
1 sibling, 1 reply; 27+ messages in thread
From: Jeff Garzik @ 2006-12-15 22:19 UTC (permalink / raw)
To: Alan
Cc: Andrew Morton, Neil Brown, Jurriaan, linux-kernel, linux-raid, Tejun Heo
Alan wrote:
> On Fri, 15 Dec 2006 13:39:27 -0800
> Andrew Morton <akpm@osdl.org> wrote:
>
>> On Fri, 15 Dec 2006 13:05:52 -0800
>> Andrew Morton <akpm@osdl.org> wrote:
>>
>>> Jeff, I shall send all the sata patches which I have at you one single time
>>> and I shall then drop the lot. So please don't flub them.
>>>
>>> I'll then do a rc1-mm2 without them.
>> hm, this is looking like a lot of work for not much gain. Rafael, are
>> you able to do a quick chop and tell us whether these:
>
> The md one and the long history of reports about parallel I/O causing
> problems sounds a lot more like the kmap stuff you were worried about
> Andrew. I'd be very intereste dto know if it happens on x86_32 built with
> a standard memory split and no highmem....
2.6.20-rc1 works, and 2.6.20-rc1 does not have the kmap_atomic() fix.
Upstream does kmap_atomic(KM_USER0) and -mm does kmap_atomic(KM_IRQ0)
Jeff
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 21:39 ` Andrew Morton
2006-12-15 21:46 ` Rafael J. Wysocki
2006-12-15 22:06 ` Alan
@ 2006-12-15 22:22 ` Rafael J. Wysocki
2006-12-15 22:24 ` Jeff Garzik
2 siblings, 1 reply; 27+ messages in thread
From: Rafael J. Wysocki @ 2006-12-15 22:22 UTC (permalink / raw)
To: Andrew Morton
Cc: Neil Brown, Jurriaan, linux-kernel, linux-raid, Jeff Garzik,
Tejun Heo, Alan
On Friday, 15 December 2006 22:39, Andrew Morton wrote:
> On Fri, 15 Dec 2006 13:05:52 -0800
> Andrew Morton <akpm@osdl.org> wrote:
>
> > Jeff, I shall send all the sata patches which I have at you one single time
> > and I shall then drop the lot. So please don't flub them.
> >
> > I'll then do a rc1-mm2 without them.
>
> hm, this is looking like a lot of work for not much gain. Rafael, are
> you able to do a quick chop and tell us whether these:
>
> pci-move-pci_vdevice-from-libata-to-core.patch
> pata_cs5530-suspend-resume-support-tweak.patch
> ata-fix-platform_device_register_simple-error-check.patch
> initializer-entry-defined-twice-in-pata_rz1000.patch
> pata_via-suspend-resume-support-fix.patch
> sata_nv-add-suspend-resume-support.patch
> libata-simulate-report-luns-for-atapi-devices.patch
> user-of-the-jiffies-rounding-patch-ata-subsystem.patch
> libata-fix-oops-with-sparsemem.patch
> sata_nv-fix-kfree-ordering-in-remove.patch
> libata-dont-initialize-sg-in-ata_exec_internal-if-dma_none-take-2.patch
> pci-quirks-fix-the-festering-mess-that-claims-to-handle-ide-quirks-ide-fix.patch
>
> are innocent?
Yes, they are.
Greetings,
Rafael
--
If you don't have the time to read,
you don't have the time or the tools to write.
- Stephen King
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 22:22 ` Rafael J. Wysocki
@ 2006-12-15 22:24 ` Jeff Garzik
2006-12-15 23:38 ` Rafael J. Wysocki
0 siblings, 1 reply; 27+ messages in thread
From: Jeff Garzik @ 2006-12-15 22:24 UTC (permalink / raw)
To: Rafael J. Wysocki
Cc: Andrew Morton, Neil Brown, Jurriaan, linux-kernel, linux-raid,
Tejun Heo, Alan
[-- Attachment #1: Type: text/plain, Size: 1470 bytes --]
Rafael J. Wysocki wrote:
> On Friday, 15 December 2006 22:39, Andrew Morton wrote:
>> On Fri, 15 Dec 2006 13:05:52 -0800
>> Andrew Morton <akpm@osdl.org> wrote:
>>
>>> Jeff, I shall send all the sata patches which I have at you one single time
>>> and I shall then drop the lot. So please don't flub them.
>>>
>>> I'll then do a rc1-mm2 without them.
>> hm, this is looking like a lot of work for not much gain. Rafael, are
>> you able to do a quick chop and tell us whether these:
>>
>> pci-move-pci_vdevice-from-libata-to-core.patch
>> pata_cs5530-suspend-resume-support-tweak.patch
>> ata-fix-platform_device_register_simple-error-check.patch
>> initializer-entry-defined-twice-in-pata_rz1000.patch
>> pata_via-suspend-resume-support-fix.patch
>> sata_nv-add-suspend-resume-support.patch
>> libata-simulate-report-luns-for-atapi-devices.patch
>> user-of-the-jiffies-rounding-patch-ata-subsystem.patch
>> libata-fix-oops-with-sparsemem.patch
>> sata_nv-fix-kfree-ordering-in-remove.patch
>> libata-dont-initialize-sg-in-ata_exec_internal-if-dma_none-take-2.patch
>> pci-quirks-fix-the-festering-mess-that-claims-to-handle-ide-quirks-ide-fix.patch
>>
>> are innocent?
>
> Yes, they are.
We all really appreciate your patience :) This is good feedback.
To narrow down some more, does applying 2.6.20-rc1 + the attached patch
work? (ignoring -mm tree altogether)
The attached patch should /basically/ be the contents of Andrew's
git-netdev-all patch.
Jeff
[-- Attachment #2: patch --]
[-- Type: text/plain, Size: 54856 bytes --]
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 984ab28..fb1de86 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -292,7 +292,7 @@ config PATA_ISAPNP
If unsure, say N.
config PATA_IT821X
- tristate "IT821x PATA support (Experimental)"
+ tristate "IT8211/2 PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the ITE 8211 and 8212
@@ -301,6 +301,15 @@ config PATA_IT821X
If unsure, say N.
+config PATA_IT8213
+ tristate "IT8213 PATA support (Experimental)"
+ depends on PCI && EXPERIMENTAL
+ help
+ This option enables support for the ITE 821 PATA
+ controllers via the new ATA layer.
+
+ If unsure, say N.
+
config PATA_JMICRON
tristate "JMicron PATA support"
depends on PCI
@@ -337,6 +346,15 @@ config PATA_MARVELL
If unsure, say N.
+config PATA_MPC52xx
+ tristate "Freescale MPC52xx SoC internal IDE"
+ depends on PPC_MPC52xx
+ help
+ This option enables support for integrated IDE controller
+ of the Freescale MPC52xx SoC.
+
+ If unsure, say N.
+
config PATA_MPIIX
tristate "Intel PATA MPIIX support"
depends on PCI
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index bc3d81a..a0df15d 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -33,11 +33,13 @@ obj-$(CONFIG_PATA_HPT3X2N) += pata_hpt3x2n.o
obj-$(CONFIG_PATA_HPT3X3) += pata_hpt3x3.o
obj-$(CONFIG_PATA_ISAPNP) += pata_isapnp.o
obj-$(CONFIG_PATA_IT821X) += pata_it821x.o
+obj-$(CONFIG_PATA_IT8213) += pata_it8213.o
obj-$(CONFIG_PATA_JMICRON) += pata_jmicron.o
obj-$(CONFIG_PATA_NETCELL) += pata_netcell.o
obj-$(CONFIG_PATA_NS87410) += pata_ns87410.o
obj-$(CONFIG_PATA_OPTI) += pata_opti.o
obj-$(CONFIG_PATA_OPTIDMA) += pata_optidma.o
+obj-$(CONFIG_PATA_MPC52xx) += pata_mpc52xx.o
obj-$(CONFIG_PATA_MARVELL) += pata_marvell.o
obj-$(CONFIG_PATA_MPIIX) += pata_mpiix.o
obj-$(CONFIG_PATA_OLDPIIX) += pata_oldpiix.o
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index f36da48..dbae6d9 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -645,8 +645,6 @@ static int ahci_reset_controller(void __iomem *mmio, struct pci_dev *pdev)
u32 cap_save, impl_save, tmp;
cap_save = readl(mmio + HOST_CAP);
- cap_save &= ( (1<<28) | (1<<17) );
- cap_save |= (1 << 27);
impl_save = readl(mmio + HOST_PORTS_IMPL);
/* global controller reset */
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index c7de0bb..7959e4c 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -226,14 +226,26 @@ static const struct pci_device_id piix_pci_tbl[] = {
{ 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
/* 2801GBM/GHM (ICH7M, identical to ICH6M) */
{ 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata_ahci },
- /* Enterprise Southbridge 2 (where's the datasheet?) */
+ /* Enterprise Southbridge 2 (631xESB/632xESB) */
{ 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
- /* SATA Controller 1 IDE (ICH8, no datasheet yet) */
+ /* SATA Controller 1 IDE (ICH8) */
{ 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
- /* SATA Controller 2 IDE (ICH8, ditto) */
+ /* SATA Controller 2 IDE (ICH8) */
{ 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
- /* Mobile SATA Controller IDE (ICH8M, ditto) */
+ /* Mobile SATA Controller IDE (ICH8M) */
{ 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9) */
+ { 0x8086, 0x2920, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9) */
+ { 0x8086, 0x2921, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9) */
+ { 0x8086, 0x2926, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9M) */
+ { 0x8086, 0x2928, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9M) */
+ { 0x8086, 0x292d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9M) */
+ { 0x8086, 0x292e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
{ } /* terminate list */
};
@@ -330,7 +342,7 @@ static const struct ata_port_operations ich_pata_ops = {
.port_start = ata_port_start,
.port_stop = ata_port_stop,
- .host_stop = ata_host_stop,
+ .host_stop = piix_host_stop,
};
static const struct ata_port_operations piix_sata_ops = {
@@ -620,7 +632,7 @@ static int piix_pata_prereset(struct ata_port *ap)
if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no]))
return -ENOENT;
-
+
ap->cbl = ATA_CBL_PATA40;
return ata_std_prereset(ap);
}
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 011c0a8..fd20e7a 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -1332,7 +1332,7 @@ unsigned ata_exec_internal_sg(struct ata_device *dev,
}
/**
- * ata_exec_internal_sg - execute libata internal command
+ * ata_exec_internal - execute libata internal command
* @dev: Device to which the command is sent
* @tf: Taskfile registers for the command and the result
* @cdb: CDB for packet command
@@ -1353,11 +1353,17 @@ unsigned ata_exec_internal(struct ata_device *dev,
struct ata_taskfile *tf, const u8 *cdb,
int dma_dir, void *buf, unsigned int buflen)
{
- struct scatterlist sg;
+ struct scatterlist *psg = NULL, sg;
+ unsigned int n_elem = 0;
- sg_init_one(&sg, buf, buflen);
+ if (dma_dir != DMA_NONE) {
+ WARN_ON(!buf);
+ sg_init_one(&sg, buf, buflen);
+ psg = &sg;
+ n_elem++;
+ }
- return ata_exec_internal_sg(dev, tf, cdb, dma_dir, &sg, 1);
+ return ata_exec_internal_sg(dev, tf, cdb, dma_dir, psg, n_elem);
}
/**
@@ -5773,7 +5779,7 @@ int ata_device_add(const struct ata_probe_ent *ent)
int rc;
DPRINTK("ENTER\n");
-
+
if (ent->irq == 0) {
dev_printk(KERN_ERR, dev, "is not available: No interrupt assigned.\n");
return 0;
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 664e137..a4790be 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -1539,7 +1539,7 @@ static unsigned int ata_scsi_rbuf_get(struct scsi_cmnd *cmd, u8 **buf_out)
struct scatterlist *sg;
sg = (struct scatterlist *) cmd->request_buffer;
- buf = kmap_atomic(sg->page, KM_USER0) + sg->offset;
+ buf = kmap_atomic(sg->page, KM_IRQ0) + sg->offset;
buflen = sg->length;
} else {
buf = cmd->request_buffer;
@@ -1567,7 +1567,7 @@ static inline void ata_scsi_rbuf_put(struct scsi_cmnd *cmd, u8 *buf)
struct scatterlist *sg;
sg = (struct scatterlist *) cmd->request_buffer;
- kunmap_atomic(buf - sg->offset, KM_USER0);
+ kunmap_atomic(buf - sg->offset, KM_IRQ0);
}
}
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index c5d61d1..2035417 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -504,7 +504,7 @@ static struct ata_port_operations ali_c5_port_ops = {
* Perform the setup on the device that must be done both at boot
* and at resume time.
*/
-
+
static void ali_init_chipset(struct pci_dev *pdev)
{
u8 rev, tmp;
@@ -655,7 +655,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
port_info[0] = port_info[1] = &info_c5;
ali_init_chipset(pdev);
-
+
isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
if (isa_bridge && rev >= 0x20 && rev < 0xC2) {
/* Are we paired with a UDMA capable chip */
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c
index 9f165a8..476b879 100644
--- a/drivers/ata/pata_cs5520.c
+++ b/drivers/ata/pata_cs5520.c
@@ -305,7 +305,7 @@ static void __devexit cs5520_remove_one(struct pci_dev *pdev)
* Do any reconfiguration work needed by a resume from RAM. We need
* to restore DMA mode support on BIOSen which disabled it
*/
-
+
static int cs5520_reinit_one(struct pci_dev *pdev)
{
u8 pcicfg;
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
index 1c62801..9b9d911 100644
--- a/drivers/ata/pata_cs5530.c
+++ b/drivers/ata/pata_cs5530.c
@@ -247,7 +247,7 @@ static int cs5530_is_palmax(void)
* Perform the chip initialisation work that is shared between both
* setup and resume paths
*/
-
+
static int cs5530_init_chip(void)
{
struct pci_dev *master_0 = NULL, *cs5530_0 = NULL, *dev = NULL;
@@ -357,11 +357,11 @@ static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &cs5530_port_ops
};
static struct ata_port_info *port_info[2] = { &info, &info };
-
+
/* Chip initialisation */
if (cs5530_init_chip())
return -ENODEV;
-
+
if (cs5530_is_palmax())
port_info[1] = &info_palmax_secondary;
@@ -375,7 +375,7 @@ static int cs5530_reinit_one(struct pci_dev *pdev)
BUG_ON(cs5530_init_chip());
return ata_pci_device_resume(pdev);
}
-
+
static const struct pci_device_id cs5530[] = {
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), },
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index 2663599..8cf167e 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -232,7 +232,7 @@ static int hpt36x_pre_reset(struct ata_port *ap)
if (!pci_test_config_bits(pdev, &hpt36x_enable_bits[ap->port_no]))
return -ENOENT;
-
+
pci_read_config_byte(pdev, 0x5A, &ata66);
if (ata66 & (1 << ap->port_no))
ap->cbl = ATA_CBL_PATA40;
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index 47082df..e51651b 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -459,7 +459,7 @@ static int hpt37x_pre_reset(struct ata_port *ap)
};
if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no]))
return -ENOENT;
-
+
pci_read_config_byte(pdev, 0x5B, &scr2);
pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
/* Cable register now active */
@@ -504,7 +504,7 @@ static int hpt374_pre_reset(struct ata_port *ap)
if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no]))
return -ENOENT;
-
+
/* Do the extra channel work */
pci_read_config_word(pdev, 0x52, &mcr3);
pci_read_config_word(pdev, 0x56, &mcr6);
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
index 5f1d385..5caf167 100644
--- a/drivers/ata/pata_hpt3x3.c
+++ b/drivers/ata/pata_hpt3x3.c
@@ -164,7 +164,7 @@ static struct ata_port_operations hpt3x3_port_ops = {
*
* Perform the setup required at boot and on resume.
*/
-
+
static void hpt3x3_init_chipset(struct pci_dev *dev)
{
u16 cmd;
diff --git a/drivers/ata/pata_it8213.c b/drivers/ata/pata_it8213.c
new file mode 100644
index 0000000..7e9a416
--- /dev/null
+++ b/drivers/ata/pata_it8213.c
@@ -0,0 +1,354 @@
+/*
+ * pata_it8213.c - iTE Tech. Inc. IT8213 PATA driver
+ *
+ * The IT8213 is a very Intel ICH like device for timing purposes, having
+ * a similar register layout and the same split clock arrangement. Cable
+ * detection is different, and it does not have slave channels or all the
+ * clutter of later ICH/SATA setups.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME "pata_it8213"
+#define DRV_VERSION "0.0.2"
+
+/**
+ * it8213_pre_reset - check for 40/80 pin
+ * @ap: Port
+ *
+ * Perform cable detection for the 8213 ATA interface. This is
+ * different to the PIIX arrangement
+ */
+
+static int it8213_pre_reset(struct ata_port *ap)
+{
+ static const struct pci_bits it8213_enable_bits[] = {
+ { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */
+ };
+
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u8 tmp;
+
+ if (!pci_test_config_bits(pdev, &it8213_enable_bits[ap->port_no]))
+ return -ENOENT;
+
+ pci_read_config_byte(pdev, 0x42, &tmp);
+ if (tmp & 2) /* The initial docs are incorrect */
+ ap->cbl = ATA_CBL_PATA40;
+ else
+ ap->cbl = ATA_CBL_PATA80;
+ return ata_std_prereset(ap);
+}
+
+/**
+ * it8213_probe_reset - Probe specified port on PATA host controller
+ * @ap: Port to probe
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void it8213_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, it8213_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ * it8213_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: um
+ *
+ * Set PIO mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int pio = adev->pio_mode - XFER_PIO_0;
+ struct pci_dev *dev = to_pci_dev(ap->host->dev);
+ unsigned int idetm_port= ap->port_no ? 0x42 : 0x40;
+ u16 idetm_data;
+ int control = 0;
+
+ /*
+ * See Intel Document 298600-004 for the timing programing rules
+ * for PIIX/ICH. The 8213 is a clone so very similar
+ */
+
+ static const /* ISP RTC */
+ u8 timings[][2] = { { 0, 0 },
+ { 0, 0 },
+ { 1, 0 },
+ { 2, 1 },
+ { 2, 3 }, };
+
+ if (pio > 2)
+ control |= 1; /* TIME1 enable */
+ if (ata_pio_need_iordy(adev)) /* PIO 3/4 require IORDY */
+ control |= 2; /* IORDY enable */
+ /* Bit 2 is set for ATAPI on the IT8213 - reverse of ICH/PIIX */
+ if (adev->class != ATA_DEV_ATA)
+ control |= 4;
+
+ pci_read_config_word(dev, idetm_port, &idetm_data);
+
+ /* Enable PPE, IE and TIME as appropriate */
+
+ if (adev->devno == 0) {
+ idetm_data &= 0xCCF0;
+ idetm_data |= control;
+ idetm_data |= (timings[pio][0] << 12) |
+ (timings[pio][1] << 8);
+ } else {
+ u8 slave_data;
+
+ idetm_data &= 0xCC0F;
+ idetm_data |= (control << 4);
+
+ /* Slave timing in seperate register */
+ pci_read_config_byte(dev, 0x44, &slave_data);
+ slave_data &= 0xF0;
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << 4;
+ pci_write_config_byte(dev, 0x44, slave_data);
+ }
+
+ idetm_data |= 0x4000; /* Ensure SITRE is enabled */
+ pci_write_config_word(dev, idetm_port, idetm_data);
+}
+
+/**
+ * it8213_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device to program
+ *
+ * Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ * This device is basically an ICH alike.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void it8213_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *dev = to_pci_dev(ap->host->dev);
+ u16 master_data;
+ u8 speed = adev->dma_mode;
+ int devid = adev->devno;
+ u8 udma_enable;
+
+ static const /* ISP RTC */
+ u8 timings[][2] = { { 0, 0 },
+ { 0, 0 },
+ { 1, 0 },
+ { 2, 1 },
+ { 2, 3 }, };
+
+ pci_read_config_word(dev, 0x40, &master_data);
+ pci_read_config_byte(dev, 0x48, &udma_enable);
+
+ if (speed >= XFER_UDMA_0) {
+ unsigned int udma = adev->dma_mode - XFER_UDMA_0;
+ u16 udma_timing;
+ u16 ideconf;
+ int u_clock, u_speed;
+
+ /* Clocks follow the PIIX style */
+ u_speed = min(2 - (udma & 1), udma);
+ if (udma == 5)
+ u_clock = 0x1000; /* 100Mhz */
+ else if (udma > 2)
+ u_clock = 1; /* 66Mhz */
+ else
+ u_clock = 0; /* 33Mhz */
+
+ udma_enable |= (1 << devid);
+
+ /* Load the UDMA mode number */
+ pci_read_config_word(dev, 0x4A, &udma_timing);
+ udma_timing &= ~(3 << (4 * devid));
+ udma_timing |= (udma & 3) << (4 * devid);
+ pci_write_config_word(dev, 0x4A, udma_timing);
+
+ /* Load the clock selection */
+ pci_read_config_word(dev, 0x54, &ideconf);
+ ideconf &= ~(0x1001 << devid);
+ ideconf |= u_clock << devid;
+ pci_write_config_word(dev, 0x54, ideconf);
+ } else {
+ /*
+ * MWDMA is driven by the PIO timings. We must also enable
+ * IORDY unconditionally along with TIME1. PPE has already
+ * been set when the PIO timing was set.
+ */
+ unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0;
+ unsigned int control;
+ u8 slave_data;
+ static const unsigned int needed_pio[3] = {
+ XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
+ };
+ int pio = needed_pio[mwdma] - XFER_PIO_0;
+
+ control = 3; /* IORDY|TIME1 */
+
+ /* If the drive MWDMA is faster than it can do PIO then
+ we must force PIO into PIO0 */
+
+ if (adev->pio_mode < needed_pio[mwdma])
+ /* Enable DMA timing only */
+ control |= 8; /* PIO cycles in PIO0 */
+
+ if (devid) { /* Slave */
+ master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */
+ master_data |= control << 4;
+ pci_read_config_byte(dev, 0x44, &slave_data);
+ slave_data &= (0x0F + 0xE1 * ap->port_no);
+ /* Load the matching timing */
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
+ pci_write_config_byte(dev, 0x44, slave_data);
+ } else { /* Master */
+ master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY
+ and master timing bits */
+ master_data |= control;
+ master_data |=
+ (timings[pio][0] << 12) |
+ (timings[pio][1] << 8);
+ }
+ udma_enable &= ~(1 << devid);
+ pci_write_config_word(dev, 0x40, master_data);
+ }
+ pci_write_config_byte(dev, 0x48, udma_enable);
+}
+
+static struct scsi_host_template it8213_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .max_sectors = ATA_MAX_SECTORS,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
+};
+
+static const struct ata_port_operations it8213_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = it8213_set_piomode,
+ .set_dmamode = it8213_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = it8213_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_pio_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_host_stop,
+};
+
+
+/**
+ * it8213_init_one - Register 8213 ATA PCI device with kernel services
+ * @pdev: PCI device to register
+ * @ent: Entry in it8213_pci_tbl matching with @pdev
+ *
+ * Called from kernel PCI layer.
+ *
+ * LOCKING:
+ * Inherited from PCI layer (may sleep).
+ *
+ * RETURNS:
+ * Zero on success, or -ERRNO value.
+ */
+
+static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ static int printed_version;
+ static struct ata_port_info info = {
+ .sht = &it8213_sht,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x1f, /* UDMA 100 */
+ .port_ops = &it8213_ops,
+ };
+ static struct ata_port_info *port_info[2] = { &info, &info };
+
+ if (!printed_version++)
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "version " DRV_VERSION "\n");
+
+ /* Current IT8213 stuff is single port */
+ return ata_pci_init_one(pdev, port_info, 1);
+}
+
+static const struct pci_device_id it8213_pci_tbl[] = {
+ { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8213), },
+
+ { } /* terminate list */
+};
+
+static struct pci_driver it8213_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = it8213_pci_tbl,
+ .probe = it8213_init_one,
+ .remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
+};
+
+static int __init it8213_init(void)
+{
+ return pci_register_driver(&it8213_pci_driver);
+}
+
+static void __exit it8213_exit(void)
+{
+ pci_unregister_driver(&it8213_pci_driver);
+}
+
+module_init(it8213_init);
+module_exit(it8213_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for the ITE 8213");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, it8213_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
index 2d661cb..efb1b6d 100644
--- a/drivers/ata/pata_jmicron.c
+++ b/drivers/ata/pata_jmicron.c
@@ -229,7 +229,7 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i
static int jmicron_reinit_one(struct pci_dev *pdev)
{
u32 reg;
-
+
switch(pdev->device) {
case PCI_DEVICE_ID_JMICRON_JMB368:
break;
diff --git a/drivers/ata/pata_marvell.c b/drivers/ata/pata_marvell.c
index 1c810ea..af93533 100644
--- a/drivers/ata/pata_marvell.c
+++ b/drivers/ata/pata_marvell.c
@@ -45,10 +45,10 @@ static int marvell_pre_reset(struct ata_port *ap)
for(i = 0; i <= 0x0F; i++)
printk("%02X:%02X ", i, readb(barp + i));
printk("\n");
-
+
devices = readl(barp + 0x0C);
pci_iounmap(pdev, barp);
-
+
if ((pdev->device == 0x6145) && (ap->port_no == 0) &&
(!(devices & 0x10))) /* PATA enable ? */
return -ENOENT;
diff --git a/drivers/ata/pata_mpc52xx.c b/drivers/ata/pata_mpc52xx.c
new file mode 100644
index 0000000..8b7019a
--- /dev/null
+++ b/drivers/ata/pata_mpc52xx.c
@@ -0,0 +1,563 @@
+/*
+ * drivers/ata/pata_mpc52xx.c
+ *
+ * libata driver for the Freescale MPC52xx on-chip IDE interface
+ *
+ * Copyright (C) 2006 Sylvain Munaut <tnt@246tNt.com>
+ * Copyright (C) 2003 Mipsys - Benjamin Herrenschmidt
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/libata.h>
+
+#include <asm/io.h>
+#include <asm/types.h>
+#include <asm/prom.h>
+#include <asm/of_platform.h>
+#include <asm/mpc52xx.h>
+
+
+#define DRV_NAME "mpc52xx_ata"
+#define DRV_VERSION "0.1.0"
+
+
+/* Private structures used by the driver */
+struct mpc52xx_ata_timings {
+ u32 pio1;
+ u32 pio2;
+};
+
+struct mpc52xx_ata_priv {
+ unsigned int ipb_period;
+ struct mpc52xx_ata __iomem * ata_regs;
+ int ata_irq;
+ struct mpc52xx_ata_timings timings[2];
+ int csel;
+};
+
+
+/* ATAPI-4 PIO specs (in ns) */
+static const int ataspec_t0[5] = {600, 383, 240, 180, 120};
+static const int ataspec_t1[5] = { 70, 50, 30, 30, 25};
+static const int ataspec_t2_8[5] = {290, 290, 290, 80, 70};
+static const int ataspec_t2_16[5] = {165, 125, 100, 80, 70};
+static const int ataspec_t2i[5] = { 0, 0, 0, 70, 25};
+static const int ataspec_t4[5] = { 30, 20, 15, 10, 10};
+static const int ataspec_ta[5] = { 35, 35, 35, 35, 35};
+
+#define CALC_CLKCYC(c,v) ((((v)+(c)-1)/(c)))
+
+
+/* Bit definitions inside the registers */
+#define MPC52xx_ATA_HOSTCONF_SMR 0x80000000UL /* State machine reset */
+#define MPC52xx_ATA_HOSTCONF_FR 0x40000000UL /* FIFO Reset */
+#define MPC52xx_ATA_HOSTCONF_IE 0x02000000UL /* Enable interrupt in PIO */
+#define MPC52xx_ATA_HOSTCONF_IORDY 0x01000000UL /* Drive supports IORDY protocol */
+
+#define MPC52xx_ATA_HOSTSTAT_TIP 0x80000000UL /* Transaction in progress */
+#define MPC52xx_ATA_HOSTSTAT_UREP 0x40000000UL /* UDMA Read Extended Pause */
+#define MPC52xx_ATA_HOSTSTAT_RERR 0x02000000UL /* Read Error */
+#define MPC52xx_ATA_HOSTSTAT_WERR 0x01000000UL /* Write Error */
+
+#define MPC52xx_ATA_FIFOSTAT_EMPTY 0x01 /* FIFO Empty */
+
+#define MPC52xx_ATA_DMAMODE_WRITE 0x01 /* Write DMA */
+#define MPC52xx_ATA_DMAMODE_READ 0x02 /* Read DMA */
+#define MPC52xx_ATA_DMAMODE_UDMA 0x04 /* UDMA enabled */
+#define MPC52xx_ATA_DMAMODE_IE 0x08 /* Enable drive interrupt to CPU in DMA mode */
+#define MPC52xx_ATA_DMAMODE_FE 0x10 /* FIFO Flush enable in Rx mode */
+#define MPC52xx_ATA_DMAMODE_FR 0x20 /* FIFO Reset */
+#define MPC52xx_ATA_DMAMODE_HUT 0x40 /* Host UDMA burst terminate */
+
+
+/* Structure of the hardware registers */
+struct mpc52xx_ata {
+
+ /* Host interface registers */
+ u32 config; /* ATA + 0x00 Host configuration */
+ u32 host_status; /* ATA + 0x04 Host controller status */
+ u32 pio1; /* ATA + 0x08 PIO Timing 1 */
+ u32 pio2; /* ATA + 0x0c PIO Timing 2 */
+ u32 mdma1; /* ATA + 0x10 MDMA Timing 1 */
+ u32 mdma2; /* ATA + 0x14 MDMA Timing 2 */
+ u32 udma1; /* ATA + 0x18 UDMA Timing 1 */
+ u32 udma2; /* ATA + 0x1c UDMA Timing 2 */
+ u32 udma3; /* ATA + 0x20 UDMA Timing 3 */
+ u32 udma4; /* ATA + 0x24 UDMA Timing 4 */
+ u32 udma5; /* ATA + 0x28 UDMA Timing 5 */
+ u32 share_cnt; /* ATA + 0x2c ATA share counter */
+ u32 reserved0[3];
+
+ /* FIFO registers */
+ u32 fifo_data; /* ATA + 0x3c */
+ u8 fifo_status_frame; /* ATA + 0x40 */
+ u8 fifo_status; /* ATA + 0x41 */
+ u16 reserved7[1];
+ u8 fifo_control; /* ATA + 0x44 */
+ u8 reserved8[5];
+ u16 fifo_alarm; /* ATA + 0x4a */
+ u16 reserved9;
+ u16 fifo_rdp; /* ATA + 0x4e */
+ u16 reserved10;
+ u16 fifo_wrp; /* ATA + 0x52 */
+ u16 reserved11;
+ u16 fifo_lfrdp; /* ATA + 0x56 */
+ u16 reserved12;
+ u16 fifo_lfwrp; /* ATA + 0x5a */
+
+ /* Drive TaskFile registers */
+ u8 tf_control; /* ATA + 0x5c TASKFILE Control/Alt Status */
+ u8 reserved13[3];
+ u16 tf_data; /* ATA + 0x60 TASKFILE Data */
+ u16 reserved14;
+ u8 tf_features; /* ATA + 0x64 TASKFILE Features/Error */
+ u8 reserved15[3];
+ u8 tf_sec_count; /* ATA + 0x68 TASKFILE Sector Count */
+ u8 reserved16[3];
+ u8 tf_sec_num; /* ATA + 0x6c TASKFILE Sector Number */
+ u8 reserved17[3];
+ u8 tf_cyl_low; /* ATA + 0x70 TASKFILE Cylinder Low */
+ u8 reserved18[3];
+ u8 tf_cyl_high; /* ATA + 0x74 TASKFILE Cylinder High */
+ u8 reserved19[3];
+ u8 tf_dev_head; /* ATA + 0x78 TASKFILE Device/Head */
+ u8 reserved20[3];
+ u8 tf_command; /* ATA + 0x7c TASKFILE Command/Status */
+ u8 dma_mode; /* ATA + 0x7d ATA Host DMA Mode configuration */
+ u8 reserved21[2];
+};
+
+
+/* ======================================================================== */
+/* Aux fns */
+/* ======================================================================== */
+
+
+/* MPC52xx low level hw control */
+
+static int
+mpc52xx_ata_compute_pio_timings(struct mpc52xx_ata_priv *priv, int dev, int pio)
+{
+ struct mpc52xx_ata_timings *timing = &priv->timings[dev];
+ unsigned int ipb_period = priv->ipb_period;
+ unsigned int t0, t1, t2_8, t2_16, t2i, t4, ta;
+
+ if ((pio<0) || (pio>4))
+ return -EINVAL;
+
+ t0 = CALC_CLKCYC(ipb_period, 1000 * ataspec_t0[pio]);
+ t1 = CALC_CLKCYC(ipb_period, 1000 * ataspec_t1[pio]);
+ t2_8 = CALC_CLKCYC(ipb_period, 1000 * ataspec_t2_8[pio]);
+ t2_16 = CALC_CLKCYC(ipb_period, 1000 * ataspec_t2_16[pio]);
+ t2i = CALC_CLKCYC(ipb_period, 1000 * ataspec_t2i[pio]);
+ t4 = CALC_CLKCYC(ipb_period, 1000 * ataspec_t4[pio]);
+ ta = CALC_CLKCYC(ipb_period, 1000 * ataspec_ta[pio]);
+
+ timing->pio1 = (t0 << 24) | (t2_8 << 16) | (t2_16 << 8) | (t2i);
+ timing->pio2 = (t4 << 24) | (t1 << 16) | (ta << 8);
+
+ return 0;
+}
+
+static void
+mpc52xx_ata_apply_timings(struct mpc52xx_ata_priv *priv, int device)
+{
+ struct mpc52xx_ata __iomem *regs = priv->ata_regs;
+ struct mpc52xx_ata_timings *timing = &priv->timings[device];
+
+ out_be32(®s->pio1, timing->pio1);
+ out_be32(®s->pio2, timing->pio2);
+ out_be32(®s->mdma1, 0);
+ out_be32(®s->mdma2, 0);
+ out_be32(®s->udma1, 0);
+ out_be32(®s->udma2, 0);
+ out_be32(®s->udma3, 0);
+ out_be32(®s->udma4, 0);
+ out_be32(®s->udma5, 0);
+
+ priv->csel = device;
+}
+
+static int
+mpc52xx_ata_hw_init(struct mpc52xx_ata_priv *priv)
+{
+ struct mpc52xx_ata __iomem *regs = priv->ata_regs;
+ int tslot;
+
+ /* Clear share_cnt (all sample code do this ...) */
+ out_be32(®s->share_cnt, 0);
+
+ /* Configure and reset host */
+ out_be32(®s->config,
+ MPC52xx_ATA_HOSTCONF_IE |
+ MPC52xx_ATA_HOSTCONF_IORDY |
+ MPC52xx_ATA_HOSTCONF_SMR |
+ MPC52xx_ATA_HOSTCONF_FR);
+
+ udelay(10);
+
+ out_be32(®s->config,
+ MPC52xx_ATA_HOSTCONF_IE |
+ MPC52xx_ATA_HOSTCONF_IORDY);
+
+ /* Set the time slot to 1us */
+ tslot = CALC_CLKCYC(priv->ipb_period, 1000000);
+ out_be32(®s->share_cnt, tslot << 16 );
+
+ /* Init timings to PIO0 */
+ memset(priv->timings, 0x00, 2*sizeof(struct mpc52xx_ata_timings));
+
+ mpc52xx_ata_compute_pio_timings(priv, 0, 0);
+ mpc52xx_ata_compute_pio_timings(priv, 1, 0);
+
+ mpc52xx_ata_apply_timings(priv, 0);
+
+ return 0;
+}
+
+
+/* ======================================================================== */
+/* libata driver */
+/* ======================================================================== */
+
+static void
+mpc52xx_ata_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct mpc52xx_ata_priv *priv = ap->host->private_data;
+ int pio, rv;
+
+ pio = adev->pio_mode - XFER_PIO_0;
+
+ rv = mpc52xx_ata_compute_pio_timings(priv, adev->devno, pio);
+
+ if (rv) {
+ printk(KERN_ERR DRV_NAME
+ ": Trying to select invalid PIO mode %d\n", pio);
+ return;
+ }
+
+ mpc52xx_ata_apply_timings(priv, adev->devno);
+}
+static void
+mpc52xx_ata_dev_select(struct ata_port *ap, unsigned int device)
+{
+ struct mpc52xx_ata_priv *priv = ap->host->private_data;
+
+ if (device != priv->csel)
+ mpc52xx_ata_apply_timings(priv, device);
+
+ ata_std_dev_select(ap,device);
+}
+
+static void
+mpc52xx_ata_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, ata_std_prereset, ata_std_softreset, NULL,
+ ata_std_postreset);
+}
+
+
+
+static struct scsi_host_template mpc52xx_ata_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .max_sectors = ATA_MAX_SECTORS,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .bios_param = ata_std_bios_param,
+};
+
+static struct ata_port_operations mpc52xx_ata_port_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = mpc52xx_ata_set_piomode,
+ .dev_select = mpc52xx_ata_dev_select,
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = mpc52xx_ata_error_handler,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_mmio_data_xfer,
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_host_stop,
+};
+
+static struct ata_probe_ent mpc52xx_ata_probe_ent = {
+ .port_ops = &mpc52xx_ata_port_ops,
+ .sht = &mpc52xx_ata_sht,
+ .n_ports = 1,
+ .pio_mask = 0x1f, /* Up to PIO4 */
+ .mwdma_mask = 0x00, /* No MWDMA */
+ .udma_mask = 0x00, /* No UDMA */
+ .port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_MMIO,
+ .irq_flags = 0,
+};
+
+static int __devinit
+mpc52xx_ata_init_one(struct device *dev, struct mpc52xx_ata_priv *priv)
+{
+ struct ata_probe_ent *ae = &mpc52xx_ata_probe_ent;
+ struct ata_ioports *aio = &ae->port[0];
+ int rv;
+
+ INIT_LIST_HEAD(&ae->node);
+ ae->dev = dev;
+ ae->irq = priv->ata_irq;
+
+ aio->cmd_addr = 0; /* Don't have a classic reg block */
+ aio->altstatus_addr = (unsigned long)&priv->ata_regs->tf_control;
+ aio->ctl_addr = (unsigned long)&priv->ata_regs->tf_control;
+ aio->data_addr = (unsigned long)&priv->ata_regs->tf_data;
+ aio->error_addr = (unsigned long)&priv->ata_regs->tf_features;
+ aio->feature_addr = (unsigned long)&priv->ata_regs->tf_features;
+ aio->nsect_addr = (unsigned long)&priv->ata_regs->tf_sec_count;
+ aio->lbal_addr = (unsigned long)&priv->ata_regs->tf_sec_num;
+ aio->lbam_addr = (unsigned long)&priv->ata_regs->tf_cyl_low;
+ aio->lbah_addr = (unsigned long)&priv->ata_regs->tf_cyl_high;
+ aio->device_addr = (unsigned long)&priv->ata_regs->tf_dev_head;
+ aio->status_addr = (unsigned long)&priv->ata_regs->tf_command;
+ aio->command_addr = (unsigned long)&priv->ata_regs->tf_command;
+
+ ae->private_data = priv;
+
+ rv = ata_device_add(ae);
+
+ return rv ? 0 : -EINVAL;
+}
+
+static struct mpc52xx_ata_priv *
+mpc52xx_ata_remove_one(struct device *dev)
+{
+ struct ata_host *host = dev_get_drvdata(dev);
+ struct mpc52xx_ata_priv *priv = host->private_data;
+
+ ata_host_remove(host);
+
+ return priv;
+}
+
+
+/* ======================================================================== */
+/* OF Platform driver */
+/* ======================================================================== */
+
+static int __devinit
+mpc52xx_ata_probe(struct of_device *op, const struct of_device_id *match)
+{
+ unsigned int ipb_freq;
+ struct resource res_mem;
+ int ata_irq = NO_IRQ;
+ struct mpc52xx_ata __iomem *ata_regs = NULL;
+ struct mpc52xx_ata_priv *priv = NULL;
+ int rv;
+
+ /* Get ipb frequency */
+ ipb_freq = mpc52xx_find_ipb_freq(op->node);
+ if (!ipb_freq) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Unable to find IPB Bus frequency\n" );
+ return -ENODEV;
+ }
+
+ /* Get IRQ and register */
+ rv = of_address_to_resource(op->node, 0, &res_mem);
+ if (rv) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while parsing device node resource\n" );
+ return rv;
+ }
+
+ ata_irq = irq_of_parse_and_map(op->node, 0);
+ if (ata_irq == NO_IRQ) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while mapping the irq\n");
+ return -EINVAL;
+ }
+
+ /* Request mem region */
+ if (!request_mem_region(res_mem.start,
+ sizeof(struct mpc52xx_ata), DRV_NAME)) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while requesting mem region\n");
+ irq_dispose_mapping(ata_irq);
+ return -EBUSY;
+ }
+
+ /* Remap registers */
+ ata_regs = ioremap(res_mem.start, sizeof(struct mpc52xx_ata));
+ if (!ata_regs) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while mapping register set\n");
+ rv = -ENOMEM;
+ goto err;
+ }
+
+ /* Prepare our private structure */
+ priv = kmalloc(sizeof(struct mpc52xx_ata_priv), GFP_ATOMIC);
+ if (!priv) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while allocating private structure\n");
+ rv = -ENOMEM;
+ goto err;
+ }
+
+ priv->ipb_period = 1000000000 / (ipb_freq / 1000);
+ priv->ata_regs = ata_regs;
+ priv->ata_irq = ata_irq;
+ priv->csel = -1;
+
+ /* Init the hw */
+ rv = mpc52xx_ata_hw_init(priv);
+ if (rv) {
+ printk(KERN_ERR DRV_NAME ": Error during HW init\n");
+ goto err;
+ }
+
+ /* Register ourselves to libata */
+ rv = mpc52xx_ata_init_one(&op->dev, priv);
+ if (rv) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while registering to ATA layer\n");
+ return rv;
+ }
+
+ /* Done */
+ return 0;
+
+ /* Error path */
+err:
+ kfree(priv);
+
+ if (ata_regs)
+ iounmap(ata_regs);
+
+ release_mem_region(res_mem.start, sizeof(struct mpc52xx_ata));
+
+ irq_dispose_mapping(ata_irq);
+
+ return rv;
+}
+
+static int
+mpc52xx_ata_remove(struct of_device *op)
+{
+ struct mpc52xx_ata_priv *priv;
+ struct resource res_mem;
+ int rv;
+
+ /* Unregister */
+ priv = mpc52xx_ata_remove_one(&op->dev);
+
+ /* Free everything */
+ iounmap(priv->ata_regs);
+
+ rv = of_address_to_resource(op->node, 0, &res_mem);
+ if (rv) {
+ printk(KERN_ERR DRV_NAME ": "
+ "Error while parsing device node resource\n");
+ printk(KERN_ERR DRV_NAME ": "
+ "Zone may not be properly released\n");
+ } else
+ release_mem_region(res_mem.start, sizeof(struct mpc52xx_ata));
+
+ irq_dispose_mapping(priv->ata_irq);
+
+ kfree(priv);
+
+ return 0;
+}
+
+
+#ifdef CONFIG_PM
+
+static int
+mpc52xx_ata_suspend(struct of_device *op, pm_message_t state)
+{
+ return 0; /* FIXME : What to do here ? */
+}
+
+static int
+mpc52xx_ata_resume(struct of_device *op)
+{
+ return 0; /* FIXME : What to do here ? */
+}
+
+#endif
+
+
+static struct of_device_id mpc52xx_ata_of_match[] = {
+ {
+ .compatible = "mpc5200-ata",
+ },
+ {
+ .compatible = "mpc52xx-ata",
+ },
+ {},
+};
+
+
+static struct of_platform_driver mpc52xx_ata_of_platform_driver = {
+ .owner = THIS_MODULE,
+ .name = DRV_NAME,
+ .match_table = mpc52xx_ata_of_match,
+ .probe = mpc52xx_ata_probe,
+ .remove = mpc52xx_ata_remove,
+#ifdef CONFIG_PM
+ .suspend = mpc52xx_ata_suspend,
+ .resume = mpc52xx_ata_resume,
+#endif
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+
+/* ======================================================================== */
+/* Module */
+/* ======================================================================== */
+
+static int __init
+mpc52xx_ata_init(void)
+{
+ printk(KERN_INFO "ata: MPC52xx IDE/ATA libata driver\n");
+ return of_register_platform_driver(&mpc52xx_ata_of_platform_driver);
+}
+
+static void __exit
+mpc52xx_ata_exit(void)
+{
+ of_unregister_platform_driver(&mpc52xx_ata_of_platform_driver);
+}
+
+module_init(mpc52xx_ata_init);
+module_exit(mpc52xx_ata_exit);
+
+MODULE_AUTHOR("Sylvain Munaut <tnt@246tNt.com>");
+MODULE_DESCRIPTION("Freescale MPC52xx IDE/ATA libata driver");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(of, mpc52xx_ata_of_match);
+MODULE_VERSION(DRV_VERSION);
+
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c
index f02b6a3..8019197 100644
--- a/drivers/ata/pata_serverworks.c
+++ b/drivers/ata/pata_serverworks.c
@@ -559,7 +559,7 @@ static int serverworks_reinit_one(struct pci_dev *pdev)
{
/* Force master latency timer to 64 PCI clocks */
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40);
-
+
switch (pdev->device)
{
case PCI_DEVICE_ID_SERVERWORKS_OSB4IDE:
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index 32cf0bf..ae07f63 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -270,7 +270,7 @@ static struct ata_port_operations sil680_port_ops = {
* is powered up on boot and when we resume in case we resumed from RAM.
* Returns the final clock settings.
*/
-
+
static u8 sil680_init_chip(struct pci_dev *pdev)
{
u32 class_rev = 0;
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index 916cedb..c434c4e 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -847,7 +847,7 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
struct sis_chipset *chipset = NULL;
static struct sis_chipset sis_chipsets[] = {
-
+
{ 0x0968, &sis_info133 },
{ 0x0966, &sis_info133 },
{ 0x0965, &sis_info133 },
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index cc09d47..9905fa8 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -384,11 +384,11 @@ static struct ata_port_operations via_port_ops_noirq = {
static void via_config_fifo(struct pci_dev *pdev, unsigned int flags)
{
u8 enable;
-
+
/* 0x40 low bits indicate enabled channels */
pci_read_config_byte(pdev, 0x40 , &enable);
enable &= 3;
-
+
if (flags & VIA_SET_FIFO) {
u8 fifo_setting[4] = {0x00, 0x60, 0x00, 0x20};
u8 fifo;
@@ -509,7 +509,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
/* Initialise the FIFO for the enabled channels. */
via_config_fifo(pdev, config->flags);
-
+
/* Clock set up */
switch(config->flags & VIA_UDMA) {
case VIA_UDMA_NONE:
@@ -568,7 +568,7 @@ static int via_reinit_one(struct pci_dev *pdev)
u32 timing;
struct ata_host *host = dev_get_drvdata(&pdev->dev);
const struct via_isa_bridge *config = host->private_data;
-
+
via_config_fifo(pdev, config->flags);
if ((config->flags & VIA_UDMA) == VIA_UDMA_66) {
@@ -583,7 +583,7 @@ static int via_reinit_one(struct pci_dev *pdev)
timing &= ~0x80008;
pci_write_config_dword(pdev, 0x50, timing);
}
- return ata_pci_device_resume(pdev);
+ return ata_pci_device_resume(pdev);
}
static const struct pci_device_id via[] = {
diff --git a/drivers/ata/pata_winbond.c b/drivers/ata/pata_winbond.c
index 3ea345c..cd5560f 100644
--- a/drivers/ata/pata_winbond.c
+++ b/drivers/ata/pata_winbond.c
@@ -5,7 +5,7 @@
* Support for the Winbond 83759A when operating in advanced mode.
* Multichip mode is not currently supported.
*/
-
+
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
@@ -69,7 +69,7 @@ static void winbond_set_piomode(struct ata_port *ap, struct ata_device *adev)
int timing = 0x88 + (ap->port_no * 4) + (adev->devno * 2);
reg = winbond_readcfg(winbond->config, 0x81);
-
+
/* Get the timing data in cycles */
if (reg & 0x40) /* Fast VLB bus, assume 50MHz */
ata_timing_compute(adev, adev->pio_mode, &t, 20000, 1000);
@@ -80,9 +80,9 @@ static void winbond_set_piomode(struct ata_port *ap, struct ata_device *adev)
recovery = (FIT(t.recover, 1, 15) + 1) & 0x0F;
timing = (active << 4) | recovery;
winbond_writecfg(winbond->config, timing, reg);
-
+
/* Load the setup timing */
-
+
reg = 0x35;
if (adev->class != ATA_DEV_ATA)
reg |= 0x08; /* FIFO off */
@@ -194,13 +194,13 @@ static __init int winbond_init_one(unsigned long port)
winbond_writecfg(port, 0x85, reg);
reg = winbond_readcfg(port, 0x81);
-
+
if (!(reg & 0x03)) /* Disabled */
return 0;
for (i = 0; i < 2 ; i ++) {
- if (reg & (1 << i)) {
+ if (reg & (1 << i)) {
/*
* Fill in a probe structure first of all
*/
@@ -217,7 +217,7 @@ static __init int winbond_init_one(unsigned long port)
ae.pio_mask = 0x1F;
ae.sht = &winbond_sht;
-
+
ae.n_ports = 1;
ae.irq = 14 + i;
ae.irq_flags = 0;
@@ -257,7 +257,7 @@ static __init int winbond_init(void)
int ct = 0;
int i;
-
+
if (probe_winbond == 0)
return -ENODEV;
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 0d316eb..49f8ff2 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -536,7 +536,7 @@ static void nv_adma_mode(struct ata_port *ap)
if (!(pp->flags & NV_ADMA_PORT_REGISTER_MODE))
return;
-
+
WARN_ON(pp->flags & NV_ADMA_ATAPI_SETUP_COMPLETE);
tmp = readw(mmio + NV_ADMA_CTL);
@@ -576,7 +576,7 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
/* Subtract 1 since an extra entry may be needed for padding, see
libata-scsi.c */
sg_tablesize = LIBATA_MAX_PRD - 1;
-
+
/* Since the legacy DMA engine is in use, we need to disable ADMA
on the port. */
adma_enable = 0;
@@ -588,7 +588,7 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
sg_tablesize = NV_ADMA_SGTBL_TOTAL_LEN;
adma_enable = 1;
}
-
+
pci_read_config_dword(pdev, NV_MCP_SATA_CFG_20, ¤t_reg);
if(ap->port_no == 1)
@@ -597,7 +597,7 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
else
config_mask = NV_MCP_SATA_CFG_20_PORT0_EN |
NV_MCP_SATA_CFG_20_PORT0_PWB_EN;
-
+
if(adma_enable) {
new_reg = current_reg | config_mask;
pp->flags &= ~NV_ADMA_ATAPI_SETUP_COMPLETE;
@@ -606,10 +606,10 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
new_reg = current_reg & ~config_mask;
pp->flags |= NV_ADMA_ATAPI_SETUP_COMPLETE;
}
-
+
if(current_reg != new_reg)
pci_write_config_dword(pdev, NV_MCP_SATA_CFG_20, new_reg);
-
+
blk_queue_bounce_limit(sdev->request_queue, bounce_limit);
blk_queue_segment_boundary(sdev->request_queue, segment_boundary);
blk_queue_max_hw_segments(sdev->request_queue, sg_tablesize);
@@ -822,13 +822,13 @@ static irqreturn_t nv_adma_interrupt(int irq, void *dev_instance)
handled++; /* irq handled if we got here */
}
}
-
+
if(notifier_clears[0] || notifier_clears[1]) {
/* Note: Both notifier clear registers must be written
if either is set, even if one is zero, according to NVIDIA. */
- writel(notifier_clears[0],
+ writel(notifier_clears[0],
nv_adma_notifier_clear_block(host->ports[0]));
- writel(notifier_clears[1],
+ writel(notifier_clears[1],
nv_adma_notifier_clear_block(host->ports[1]));
}
diff --git a/drivers/ata/sata_sis.c b/drivers/ata/sata_sis.c
index 9c25a1e..c90fb13 100644
--- a/drivers/ata/sata_sis.c
+++ b/drivers/ata/sata_sis.c
@@ -42,7 +42,7 @@
#include <linux/libata.h>
#define DRV_NAME "sata_sis"
-#define DRV_VERSION "0.6"
+#define DRV_VERSION "0.7"
enum {
sis_180 = 0,
@@ -67,9 +67,12 @@ static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg);
static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static const struct pci_device_id sis_pci_tbl[] = {
- { PCI_VDEVICE(SI, 0x180), sis_180 },
- { PCI_VDEVICE(SI, 0x181), sis_180 },
- { PCI_VDEVICE(SI, 0x182), sis_180 },
+ { PCI_VDEVICE(SI, 0x0180), sis_180 }, /* SiS 964/180 */
+ { PCI_VDEVICE(SI, 0x0181), sis_180 }, /* SiS 964/180 */
+ { PCI_VDEVICE(SI, 0x0182), sis_180 }, /* SiS 965/965L */
+ { PCI_VDEVICE(SI, 0x0183), sis_180 }, /* SiS 965/965L */
+ { PCI_VDEVICE(SI, 0x1182), sis_180 }, /* SiS 966/966L */
+ { PCI_VDEVICE(SI, 0x1183), sis_180 }, /* SiS 966/966L */
{ } /* terminate list */
};
@@ -142,24 +145,32 @@ MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, sis_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-static unsigned int get_scr_cfg_addr(unsigned int port_no, unsigned int sc_reg, int device)
+static unsigned int get_scr_cfg_addr(unsigned int port_no, unsigned int sc_reg, struct pci_dev *pdev)
{
unsigned int addr = SIS_SCR_BASE + (4 * sc_reg);
if (port_no) {
- if (device == 0x182)
- addr += SIS182_SATA1_OFS;
- else
- addr += SIS180_SATA1_OFS;
+ switch (pdev->device) {
+ case 0x0180:
+ case 0x0181:
+ addr += SIS180_SATA1_OFS;
+ break;
+
+ case 0x0182:
+ case 0x0183:
+ case 0x1182:
+ case 0x1183:
+ addr += SIS182_SATA1_OFS;
+ break;
+ }
}
-
return addr;
}
static u32 sis_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, sc_reg, pdev->device);
+ unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, sc_reg, pdev);
u32 val, val2 = 0;
u8 pmr;
@@ -170,7 +181,8 @@ static u32 sis_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
pci_read_config_dword(pdev, cfg_addr, &val);
- if ((pdev->device == 0x182) || (pmr & SIS_PMR_COMBINED))
+ if ((pdev->device == 0x0182) || (pdev->device == 0x0183) || (pdev->device == 0x1182) ||
+ (pdev->device == 0x1183) || (pmr & SIS_PMR_COMBINED))
pci_read_config_dword(pdev, cfg_addr+0x10, &val2);
return (val|val2) & 0xfffffffb; /* avoid problems with powerdowned ports */
@@ -179,7 +191,7 @@ static u32 sis_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
static void sis_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, scr, pdev->device);
+ unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, scr, pdev);
u8 pmr;
if (scr == SCR_ERROR) /* doesn't exist in PCI cfg space */
@@ -189,7 +201,8 @@ static void sis_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val)
pci_write_config_dword(pdev, cfg_addr, val);
- if ((pdev->device == 0x182) || (pmr & SIS_PMR_COMBINED))
+ if ((pdev->device == 0x0182) || (pdev->device == 0x0183) || (pdev->device == 0x1182) ||
+ (pdev->device == 0x1183) || (pmr & SIS_PMR_COMBINED))
pci_write_config_dword(pdev, cfg_addr+0x10, val);
}
@@ -209,7 +222,8 @@ static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg)
val = inl(ap->ioaddr.scr_addr + (sc_reg * 4));
- if ((pdev->device == 0x182) || (pmr & SIS_PMR_COMBINED))
+ if ((pdev->device == 0x0182) || (pdev->device == 0x0183) || (pdev->device == 0x1182) ||
+ (pdev->device == 0x1183) || (pmr & SIS_PMR_COMBINED))
val2 = inl(ap->ioaddr.scr_addr + (sc_reg * 4) + 0x10);
return (val | val2) & 0xfffffffb;
@@ -229,7 +243,8 @@ static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
sis_scr_cfg_write(ap, sc_reg, val);
else {
outl(val, ap->ioaddr.scr_addr + (sc_reg * 4));
- if ((pdev->device == 0x182) || (pmr & SIS_PMR_COMBINED))
+ if ((pdev->device == 0x0182) || (pdev->device == 0x0183) || (pdev->device == 0x1182) ||
+ (pdev->device == 0x1183) || (pmr & SIS_PMR_COMBINED))
outl(val, ap->ioaddr.scr_addr + (sc_reg * 4)+0x10);
}
}
@@ -243,7 +258,7 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
struct ata_port_info pi = sis_port_info, *ppi[2] = { &pi, &pi };
int pci_dev_busy = 0;
u8 pmr;
- u8 port2_start;
+ u8 port2_start = 0x20;
if (!printed_version++)
dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
@@ -282,28 +297,42 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
}
pci_read_config_byte(pdev, SIS_PMR, &pmr);
- if (ent->device != 0x182) {
+ switch (ent->device) {
+ case 0x0180:
+ case 0x0181:
if ((pmr & SIS_PMR_COMBINED) == 0) {
dev_printk(KERN_INFO, &pdev->dev,
"Detected SiS 180/181/964 chipset in SATA mode\n");
port2_start = 64;
- }
- else {
+ } else {
dev_printk(KERN_INFO, &pdev->dev,
"Detected SiS 180/181 chipset in combined mode\n");
port2_start=0;
pi.flags |= ATA_FLAG_SLAVE_POSS;
}
- }
- else {
+ break;
+
+ case 0x0182:
+ case 0x0183:
pci_read_config_dword ( pdev, 0x6C, &val);
if (val & (1L << 31)) {
dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 182/965 chipset\n");
pi.flags |= ATA_FLAG_SLAVE_POSS;
- }
- else
+ } else {
dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 182/965L chipset\n");
- port2_start = 0x20;
+ }
+ break;
+
+ case 0x1182:
+ case 0x1183:
+ pci_read_config_dword(pdev, 0x64, &val);
+ if (val & 0x10000000) {
+ dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 1182/1183/966L SATA controller\n");
+ } else {
+ dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 1182/1183/966 SATA controller\n");
+ pi.flags |= ATA_FLAG_SLAVE_POSS;
+ }
+ break;
}
probe_ent = ata_pci_init_native_mode(pdev, ppi, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY);
diff --git a/drivers/ata/sata_svw.c b/drivers/ata/sata_svw.c
index db32d15..d89c959 100644
--- a/drivers/ata/sata_svw.c
+++ b/drivers/ata/sata_svw.c
@@ -56,6 +56,8 @@
#define DRV_VERSION "2.0"
enum {
+ K2_FLAG_NO_ATAPI_DMA = (1 << 29),
+
/* Taskfile registers offsets */
K2_SATA_TF_CMD_OFFSET = 0x00,
K2_SATA_TF_DATA_OFFSET = 0x00,
@@ -83,11 +85,33 @@ enum {
/* Port stride */
K2_SATA_PORT_OFFSET = 0x100,
+
+ board_svw4 = 0,
+ board_svw8 = 1,
+};
+
+static const struct k2_board_info {
+ unsigned int n_ports;
+ unsigned long port_flags;
+} k2_board_info[] = {
+ /* board_svw4 */
+ { 4, K2_FLAG_NO_ATAPI_DMA },
+
+ /* board_svw8 */
+ { 8, K2_FLAG_NO_ATAPI_DMA },
};
static u8 k2_stat_check_status(struct ata_port *ap);
+static int k2_sata_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+ if (qc->ap->flags & K2_FLAG_NO_ATAPI_DMA)
+ return -1; /* ATAPI DMA not supported */
+
+ return 0;
+}
+
static u32 k2_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
{
if (sc_reg > SCR_CONTROL)
@@ -313,6 +337,7 @@ static const struct ata_port_operations k2_sata_ops = {
.check_status = k2_stat_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
+ .check_atapi_dma = k2_sata_check_atapi_dma,
.bmdma_setup = k2_bmdma_setup_mmio,
.bmdma_start = k2_bmdma_start_mmio,
.bmdma_stop = ata_bmdma_stop,
@@ -359,6 +384,8 @@ static int k2_sata_init_one (struct pci_dev *pdev, const struct pci_device_id *e
struct ata_probe_ent *probe_ent = NULL;
unsigned long base;
void __iomem *mmio_base;
+ const struct k2_board_info *board_info =
+ &k2_board_info[ent->driver_data];
int pci_dev_busy = 0;
int rc;
int i;
@@ -424,7 +451,7 @@ static int k2_sata_init_one (struct pci_dev *pdev, const struct pci_device_id *e
probe_ent->sht = &k2_sata_sht;
probe_ent->port_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_MMIO;
+ ATA_FLAG_MMIO | board_info->port_flags;
probe_ent->port_ops = &k2_sata_ops;
probe_ent->n_ports = 4;
probe_ent->irq = pdev->irq;
@@ -441,7 +468,7 @@ static int k2_sata_init_one (struct pci_dev *pdev, const struct pci_device_id *e
/* different controllers have different number of ports - currently 4 or 8 */
/* All ports are on the same function. Multi-function device is no
* longer available. This should not be seen in any system. */
- for (i = 0; i < ent->driver_data; i++)
+ for (i = 0; i < board_info->n_ports; i++)
k2_sata_setup_port(&probe_ent->port[i], base + i * K2_SATA_PORT_OFFSET);
pci_set_master(pdev);
@@ -469,11 +496,11 @@ err_out:
* controller
* */
static const struct pci_device_id k2_sata_pci_tbl[] = {
- { PCI_VDEVICE(SERVERWORKS, 0x0240), 4 },
- { PCI_VDEVICE(SERVERWORKS, 0x0241), 4 },
- { PCI_VDEVICE(SERVERWORKS, 0x0242), 8 },
- { PCI_VDEVICE(SERVERWORKS, 0x024a), 4 },
- { PCI_VDEVICE(SERVERWORKS, 0x024b), 4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0240), board_svw4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0241), board_svw4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0242), board_svw8 },
+ { PCI_VDEVICE(SERVERWORKS, 0x024a), board_svw4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x024b), board_svw4 },
{ }
};
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index 1c7f19a..8c2335c 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -319,7 +319,7 @@ static struct ata_probe_ent *vt6420_init_probe_ent(struct pci_dev *pdev)
{
struct ata_probe_ent *probe_ent;
struct ata_port_info *ppi[2];
-
+
ppi[0] = ppi[1] = &vt6420_port_info;
probe_ent = ata_pci_init_native_mode(pdev, ppi, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY);
if (!probe_ent)
diff --git a/include/linux/libata.h b/include/linux/libata.h
index ab27548..9356322 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -307,7 +307,7 @@ enum {
* most devices.
*/
ATA_SPINUP_WAIT = 8000,
-
+
/* Horkage types. May be set by libata or controller on drives
(some horkage may be drive/controller pair dependant */
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 95c1e74..ff9e6d3 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -1621,6 +1621,7 @@
#define PCI_VENDOR_ID_ITE 0x1283
#define PCI_DEVICE_ID_ITE_8211 0x8211
#define PCI_DEVICE_ID_ITE_8212 0x8212
+#define PCI_DEVICE_ID_ITE_8213 0x8213
#define PCI_DEVICE_ID_ITE_8872 0x8872
#define PCI_DEVICE_ID_ITE_IT8330G_0 0xe886
^ permalink raw reply related [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 22:19 ` Jeff Garzik
@ 2006-12-15 22:27 ` Rafael J. Wysocki
0 siblings, 0 replies; 27+ messages in thread
From: Rafael J. Wysocki @ 2006-12-15 22:27 UTC (permalink / raw)
To: Jeff Garzik
Cc: Alan, Andrew Morton, Neil Brown, Jurriaan, linux-kernel,
linux-raid, Tejun Heo
On Friday, 15 December 2006 23:19, Jeff Garzik wrote:
> Alan wrote:
> > On Fri, 15 Dec 2006 13:39:27 -0800
> > Andrew Morton <akpm@osdl.org> wrote:
> >
> >> On Fri, 15 Dec 2006 13:05:52 -0800
> >> Andrew Morton <akpm@osdl.org> wrote:
> >>
> >>> Jeff, I shall send all the sata patches which I have at you one single time
> >>> and I shall then drop the lot. So please don't flub them.
> >>>
> >>> I'll then do a rc1-mm2 without them.
> >> hm, this is looking like a lot of work for not much gain. Rafael, are
> >> you able to do a quick chop and tell us whether these:
> >
> > The md one and the long history of reports about parallel I/O causing
> > problems sounds a lot more like the kmap stuff you were worried about
> > Andrew. I'd be very intereste dto know if it happens on x86_32 built with
> > a standard memory split and no highmem....
>
> 2.6.20-rc1 works, and 2.6.20-rc1 does not have the kmap_atomic() fix.
>
> Upstream does kmap_atomic(KM_USER0) and -mm does kmap_atomic(KM_IRQ0)
On x86_64 that shouldn't be a problem, I think, and my machine is an x86_64
one.
Greetings,
Rafael
--
If you don't have the time to read,
you don't have the time or the tools to write.
- Stephen King
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 22:24 ` Jeff Garzik
@ 2006-12-15 23:38 ` Rafael J. Wysocki
2006-12-16 9:56 ` Rafael J. Wysocki
0 siblings, 1 reply; 27+ messages in thread
From: Rafael J. Wysocki @ 2006-12-15 23:38 UTC (permalink / raw)
To: Jeff Garzik
Cc: Andrew Morton, Neil Brown, Jurriaan, linux-kernel, linux-raid,
Tejun Heo, Alan
On Friday, 15 December 2006 23:24, Jeff Garzik wrote:
> Rafael J. Wysocki wrote:
> > On Friday, 15 December 2006 22:39, Andrew Morton wrote:
> >> On Fri, 15 Dec 2006 13:05:52 -0800
> >> Andrew Morton <akpm@osdl.org> wrote:
> >>
> >>> Jeff, I shall send all the sata patches which I have at you one single time
> >>> and I shall then drop the lot. So please don't flub them.
> >>>
> >>> I'll then do a rc1-mm2 without them.
> >> hm, this is looking like a lot of work for not much gain. Rafael, are
> >> you able to do a quick chop and tell us whether these:
> >>
> >> pci-move-pci_vdevice-from-libata-to-core.patch
> >> pata_cs5530-suspend-resume-support-tweak.patch
> >> ata-fix-platform_device_register_simple-error-check.patch
> >> initializer-entry-defined-twice-in-pata_rz1000.patch
> >> pata_via-suspend-resume-support-fix.patch
> >> sata_nv-add-suspend-resume-support.patch
> >> libata-simulate-report-luns-for-atapi-devices.patch
> >> user-of-the-jiffies-rounding-patch-ata-subsystem.patch
> >> libata-fix-oops-with-sparsemem.patch
> >> sata_nv-fix-kfree-ordering-in-remove.patch
> >> libata-dont-initialize-sg-in-ata_exec_internal-if-dma_none-take-2.patch
> >> pci-quirks-fix-the-festering-mess-that-claims-to-handle-ide-quirks-ide-fix.patch
> >>
> >> are innocent?
> >
> > Yes, they are.
>
> We all really appreciate your patience :) This is good feedback.
>
> To narrow down some more, does applying 2.6.20-rc1 + the attached patch
> work? (ignoring -mm tree altogether)
Yes, it does.
Greetings,
Rafael
--
If you don't have the time to read,
you don't have the time or the tools to write.
- Stephen King
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 21:48 ` Jeff Garzik
@ 2006-12-16 6:03 ` thunder7
0 siblings, 0 replies; 27+ messages in thread
From: thunder7 @ 2006-12-16 6:03 UTC (permalink / raw)
To: Jeff Garzik
Cc: Andrew Morton, Neil Brown, Jurriaan, linux-kernel, linux-raid, Tejun Heo
From: Jeff Garzik <jeff@garzik.org>
Date: Fri, Dec 15, 2006 at 04:48:44PM -0500
> The "Re: Linux 2.6.20-rc1" sub-thread that had Jens and Alistair John
> Strachan replying seemed to implicate some core block layer badness.
>
The original problem (not mounting my raid6 partition) is observable in
2.6.20-rc1-mm1, but not in 2.6.20-rc1; ie. 2.6.20-rc1 is good for me.
Linux version 2.6.20-rc1 (jurriaan@middle) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #3 SMP Fri Dec 15 21:19:54 CET 2006
<snip>
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdh1 ...
md: adding sdh1 ...
md: adding sdg1 ...
md: adding sdf1 ...
md: adding sde1 ...
md: adding sdd1 ...
md: adding sdc1 ...
md: adding sdb1 ...
md: adding sda1 ...
md: hdc9 has different UUID to sdh1
md: hdc8 has different UUID to sdh1
md: hdc7 has different UUID to sdh1
md: hdc6 has different UUID to sdh1
md: hdc5 has different UUID to sdh1
md: hda9 has different UUID to sdh1
md: hda8 has different UUID to sdh1
md: hda7 has different UUID to sdh1
md: hda6 has different UUID to sdh1
md: hda5 has different UUID to sdh1
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: bind<sdc1>
md: bind<sdd1>
md: bind<sde1>
md: bind<sdf1>
md: bind<sdg1>
md: bind<sdh1>
md: running: <sdh1><sdg1><sdf1><sde1><sdd1><sdc1><sdb1><sda1>
raid5: device sdh1 operational as raid disk 1
raid5: device sdg1 operational as raid disk 0
raid5: device sdf1 operational as raid disk 5
raid5: device sde1 operational as raid disk 6
raid5: device sdd1 operational as raid disk 7
raid5: device sdc1 operational as raid disk 3
raid5: device sdb1 operational as raid disk 2
raid5: device sda1 operational as raid disk 4
raid5: allocated 8462kB for md0
raid5: raid level 6 set md0 active with 8 out of 8 devices, algorithm 2
RAID5 conf printout:
--- rd:8 wd:8
disk 0, o:1, dev:sdg1
disk 1, o:1, dev:sdh1
disk 2, o:1, dev:sdb1
disk 3, o:1, dev:sdc1
disk 4, o:1, dev:sda1
disk 5, o:1, dev:sdf1
disk 6, o:1, dev:sde1
disk 7, o:1, dev:sdd1
md0: bitmap initialized from disk: read 15/15 pages, set 1 bits, status: 0
created bitmap (233 pages) for device md0
md: considering hdc9 ...
md: adding hdc9 ...
md: hdc8 has different UUID to hdc9
md: hdc7 has different UUID to hdc9
md: hdc6 has different UUID to hdc9
md: hdc5 has different UUID to hdc9
md: adding hda9 ...
md: hda8 has different UUID to hdc9
md: hda7 has different UUID to hdc9
md: hda6 has different UUID to hdc9
md: hda5 has different UUID to hdc9
md: created md4
md: bind<hda9>
md: bind<hdc9>
md: running: <hdc9><hda9>
raid1: raid set md4 active with 2 out of 2 mirrors
md4: bitmap initialized from disk: read 10/10 pages, set 45 bits, status: 0
<snip>
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Jurriaan
--
And I thought that the Borg were bad...
Debian (Unstable) GNU/Linux 2.6.20-rc1 2x4023 bogomips load 5.55
the Jack Vance Integral Edition: http://www.integralarchive.org
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-15 23:38 ` Rafael J. Wysocki
@ 2006-12-16 9:56 ` Rafael J. Wysocki
2006-12-16 11:16 ` Rafael J. Wysocki
0 siblings, 1 reply; 27+ messages in thread
From: Rafael J. Wysocki @ 2006-12-16 9:56 UTC (permalink / raw)
To: Andrew Morton
Cc: Jeff Garzik, Neil Brown, Jurriaan, linux-kernel, linux-raid,
Tejun Heo, Alan
On Saturday, 16 December 2006 00:38, Rafael J. Wysocki wrote:
> On Friday, 15 December 2006 23:24, Jeff Garzik wrote:
> > Rafael J. Wysocki wrote:
> > > On Friday, 15 December 2006 22:39, Andrew Morton wrote:
> > >> On Fri, 15 Dec 2006 13:05:52 -0800
> > >> Andrew Morton <akpm@osdl.org> wrote:
> > >>
> > >>> Jeff, I shall send all the sata patches which I have at you one single time
> > >>> and I shall then drop the lot. So please don't flub them.
> > >>>
> > >>> I'll then do a rc1-mm2 without them.
> > >> hm, this is looking like a lot of work for not much gain. Rafael, are
> > >> you able to do a quick chop and tell us whether these:
> > >>
> > >> pci-move-pci_vdevice-from-libata-to-core.patch
> > >> pata_cs5530-suspend-resume-support-tweak.patch
> > >> ata-fix-platform_device_register_simple-error-check.patch
> > >> initializer-entry-defined-twice-in-pata_rz1000.patch
> > >> pata_via-suspend-resume-support-fix.patch
> > >> sata_nv-add-suspend-resume-support.patch
> > >> libata-simulate-report-luns-for-atapi-devices.patch
> > >> user-of-the-jiffies-rounding-patch-ata-subsystem.patch
> > >> libata-fix-oops-with-sparsemem.patch
> > >> sata_nv-fix-kfree-ordering-in-remove.patch
> > >> libata-dont-initialize-sg-in-ata_exec_internal-if-dma_none-take-2.patch
> > >> pci-quirks-fix-the-festering-mess-that-claims-to-handle-ide-quirks-ide-fix.patch
> > >>
> > >> are innocent?
> > >
> > > Yes, they are.
> >
> > We all really appreciate your patience :) This is good feedback.
> >
> > To narrow down some more, does applying 2.6.20-rc1 + the attached patch
> > work? (ignoring -mm tree altogether)
>
> Yes, it does.
I've applied the patches from -rc1-mm1 up to and including
problem-phy-probe-not-working-properly-for-ibm_emac-ppc4xx.patch
on top of 2.6.20-rc1 and they don't seem to break anything. Will try some
more.
Greetings,
Rafael
--
If you don't have the time to read,
you don't have the time or the tools to write.
- Stephen King
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-16 9:56 ` Rafael J. Wysocki
@ 2006-12-16 11:16 ` Rafael J. Wysocki
2006-12-17 11:00 ` Rafael J. Wysocki
0 siblings, 1 reply; 27+ messages in thread
From: Rafael J. Wysocki @ 2006-12-16 11:16 UTC (permalink / raw)
To: Andrew Morton
Cc: Jeff Garzik, Neil Brown, Jurriaan, linux-kernel, linux-raid,
Tejun Heo, Alan
On Saturday, 16 December 2006 10:56, Rafael J. Wysocki wrote:
> On Saturday, 16 December 2006 00:38, Rafael J. Wysocki wrote:
> > On Friday, 15 December 2006 23:24, Jeff Garzik wrote:
> > > Rafael J. Wysocki wrote:
> > > > On Friday, 15 December 2006 22:39, Andrew Morton wrote:
> > > >> On Fri, 15 Dec 2006 13:05:52 -0800
> > > >> Andrew Morton <akpm@osdl.org> wrote:
> > > >>
> > > >>> Jeff, I shall send all the sata patches which I have at you one single time
> > > >>> and I shall then drop the lot. So please don't flub them.
> > > >>>
> > > >>> I'll then do a rc1-mm2 without them.
> > > >> hm, this is looking like a lot of work for not much gain. Rafael, are
> > > >> you able to do a quick chop and tell us whether these:
> > > >>
> > > >> pci-move-pci_vdevice-from-libata-to-core.patch
> > > >> pata_cs5530-suspend-resume-support-tweak.patch
> > > >> ata-fix-platform_device_register_simple-error-check.patch
> > > >> initializer-entry-defined-twice-in-pata_rz1000.patch
> > > >> pata_via-suspend-resume-support-fix.patch
> > > >> sata_nv-add-suspend-resume-support.patch
> > > >> libata-simulate-report-luns-for-atapi-devices.patch
> > > >> user-of-the-jiffies-rounding-patch-ata-subsystem.patch
> > > >> libata-fix-oops-with-sparsemem.patch
> > > >> sata_nv-fix-kfree-ordering-in-remove.patch
> > > >> libata-dont-initialize-sg-in-ata_exec_internal-if-dma_none-take-2.patch
> > > >> pci-quirks-fix-the-festering-mess-that-claims-to-handle-ide-quirks-ide-fix.patch
> > > >>
> > > >> are innocent?
> > > >
> > > > Yes, they are.
> > >
> > > We all really appreciate your patience :) This is good feedback.
> > >
> > > To narrow down some more, does applying 2.6.20-rc1 + the attached patch
> > > work? (ignoring -mm tree altogether)
> >
> > Yes, it does.
>
> I've applied the patches from -rc1-mm1 up to and including
>
> problem-phy-probe-not-working-properly-for-ibm_emac-ppc4xx.patch
>
> on top of 2.6.20-rc1 and they don't seem to break anything. Will try some
> more.
The patch that breaks things is somewhere between
dont-export-device-ids-to-userspace.patch
and
funsoft-is-bust-on-sparc.patch
inclusive.
Now I'll need to resync my disk arrays so if anyone has any suggestions
what to try next, I'll be grateful. ;-)
Greetings,
Rafael
--
If you don't have the time to read,
you don't have the time or the tools to write.
- Stephen King
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-16 11:16 ` Rafael J. Wysocki
@ 2006-12-17 11:00 ` Rafael J. Wysocki
2006-12-17 11:05 ` Andrew Morton
2006-12-17 14:08 ` Jiri Slaby
0 siblings, 2 replies; 27+ messages in thread
From: Rafael J. Wysocki @ 2006-12-17 11:00 UTC (permalink / raw)
To: Andrew Morton
Cc: Jeff Garzik, Neil Brown, Jurriaan, linux-kernel, linux-raid,
Tejun Heo, Alan, Luben Tuikov
On Saturday, 16 December 2006 12:16, Rafael J. Wysocki wrote:
> On Saturday, 16 December 2006 10:56, Rafael J. Wysocki wrote:
> > On Saturday, 16 December 2006 00:38, Rafael J. Wysocki wrote:
> > > On Friday, 15 December 2006 23:24, Jeff Garzik wrote:
> > > > Rafael J. Wysocki wrote:
> > > > > On Friday, 15 December 2006 22:39, Andrew Morton wrote:
> > > > >> On Fri, 15 Dec 2006 13:05:52 -0800
> > > > >> Andrew Morton <akpm@osdl.org> wrote:
> > > > >>
> > > > >>> Jeff, I shall send all the sata patches which I have at you one single time
> > > > >>> and I shall then drop the lot. So please don't flub them.
> > > > >>>
> > > > >>> I'll then do a rc1-mm2 without them.
> > > > >> hm, this is looking like a lot of work for not much gain. Rafael, are
> > > > >> you able to do a quick chop and tell us whether these:
> > > > >>
> > > > >> pci-move-pci_vdevice-from-libata-to-core.patch
> > > > >> pata_cs5530-suspend-resume-support-tweak.patch
> > > > >> ata-fix-platform_device_register_simple-error-check.patch
> > > > >> initializer-entry-defined-twice-in-pata_rz1000.patch
> > > > >> pata_via-suspend-resume-support-fix.patch
> > > > >> sata_nv-add-suspend-resume-support.patch
> > > > >> libata-simulate-report-luns-for-atapi-devices.patch
> > > > >> user-of-the-jiffies-rounding-patch-ata-subsystem.patch
> > > > >> libata-fix-oops-with-sparsemem.patch
> > > > >> sata_nv-fix-kfree-ordering-in-remove.patch
> > > > >> libata-dont-initialize-sg-in-ata_exec_internal-if-dma_none-take-2.patch
> > > > >> pci-quirks-fix-the-festering-mess-that-claims-to-handle-ide-quirks-ide-fix.patch
> > > > >>
> > > > >> are innocent?
> > > > >
> > > > > Yes, they are.
> > > >
> > > > We all really appreciate your patience :) This is good feedback.
> > > >
> > > > To narrow down some more, does applying 2.6.20-rc1 + the attached patch
> > > > work? (ignoring -mm tree altogether)
> > >
> > > Yes, it does.
> >
> > I've applied the patches from -rc1-mm1 up to and including
> >
> > problem-phy-probe-not-working-properly-for-ibm_emac-ppc4xx.patch
> >
> > on top of 2.6.20-rc1 and they don't seem to break anything. Will try some
> > more.
>
> The patch that breaks things is somewhere between
>
> dont-export-device-ids-to-userspace.patch
>
> and
>
> funsoft-is-bust-on-sparc.patch
>
> inclusive.
>
> Now I'll need to resync my disk arrays so if anyone has any suggestions
> what to try next, I'll be grateful. ;-)
Okay, I have identified the patch that causes the problem to appear, which is
fix-sense-key-medium-error-processing-and-retry.patch
With this patch reverted -rc1-mm1 is happily running on my test box.
Greetings,
Rafael
--
If you don't have the time to read,
you don't have the time or the tools to write.
- Stephen King
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-17 11:00 ` Rafael J. Wysocki
@ 2006-12-17 11:05 ` Andrew Morton
2006-12-17 16:00 ` thunder7
2006-12-17 14:08 ` Jiri Slaby
1 sibling, 1 reply; 27+ messages in thread
From: Andrew Morton @ 2006-12-17 11:05 UTC (permalink / raw)
To: Rafael J. Wysocki
Cc: Jeff Garzik, Neil Brown, Jurriaan, linux-kernel, linux-raid,
Tejun Heo, Alan, Luben Tuikov
On Sun, 17 Dec 2006 12:00:12 +0100
"Rafael J. Wysocki" <rjw@sisk.pl> wrote:
> Okay, I have identified the patch that causes the problem to appear, which is
>
> fix-sense-key-medium-error-processing-and-retry.patch
>
> With this patch reverted -rc1-mm1 is happily running on my test box.
That was rather unexpected. Thanks.
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-17 11:00 ` Rafael J. Wysocki
2006-12-17 11:05 ` Andrew Morton
@ 2006-12-17 14:08 ` Jiri Slaby
1 sibling, 0 replies; 27+ messages in thread
From: Jiri Slaby @ 2006-12-17 14:08 UTC (permalink / raw)
To: Rafael J. Wysocki
Cc: Andrew Morton, Jeff Garzik, Neil Brown, Jurriaan, linux-kernel,
linux-raid, Tejun Heo, Alan, Luben Tuikov
Rafael J. Wysocki wrote:
> Okay, I have identified the patch that causes the problem to appear, which is
>
> fix-sense-key-medium-error-processing-and-retry.patch
>
> With this patch reverted -rc1-mm1 is happily running on my test box.
Yes! Here too. Good work.
regards,
--
http://www.fi.muni.cz/~xslaby/ Jiri Slaby
faculty of informatics, masaryk university, brno, cz
e-mail: jirislaby gmail com, gpg pubkey fingerprint:
B674 9967 0407 CE62 ACC8 22A0 32CC 55C3 39D4 7A7E
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-17 11:05 ` Andrew Morton
@ 2006-12-17 16:00 ` thunder7
2006-12-19 23:26 ` Luben Tuikov
0 siblings, 1 reply; 27+ messages in thread
From: thunder7 @ 2006-12-17 16:00 UTC (permalink / raw)
To: Andrew Morton
Cc: Rafael J. Wysocki, Jeff Garzik, Neil Brown, Jurriaan,
linux-kernel, linux-raid, Tejun Heo, Alan, Luben Tuikov
From: Andrew Morton <akpm@osdl.org>
Date: Sun, Dec 17, 2006 at 03:05:39AM -0800
> On Sun, 17 Dec 2006 12:00:12 +0100
> "Rafael J. Wysocki" <rjw@sisk.pl> wrote:
>
> > Okay, I have identified the patch that causes the problem to appear, which is
> >
> > fix-sense-key-medium-error-processing-and-retry.patch
> >
> > With this patch reverted -rc1-mm1 is happily running on my test box.
>
> That was rather unexpected. Thanks.
>
I can confirm that 2.6.20-rc1-mm1 with this patch reverted mounts my
raid6 partition without problems. This is x86_64 with SMP.
Kind regards,
Jurriaan
--
HORROR FILM WISDOM:
9. If your car runs out of gas at night, do not go to the nearby
deserted-looking house to phone for help.
Debian (Unstable) GNU/Linux 2.6.20-rc1 2x2011 bogomips load 7.42
the Jack Vance Integral Edition: http://www.integralarchive.org
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-17 16:00 ` thunder7
@ 2006-12-19 23:26 ` Luben Tuikov
2006-12-20 0:08 ` Andrew Morton
0 siblings, 1 reply; 27+ messages in thread
From: Luben Tuikov @ 2006-12-19 23:26 UTC (permalink / raw)
To: Jurriaan, Andrew Morton
Cc: Rafael J. Wysocki, Jeff Garzik, Neil Brown, Jurriaan,
linux-kernel, linux-raid, Tejun Heo, Alan, Luben Tuikov
--- thunder7@xs4all.nl wrote:
> From: Andrew Morton <akpm@osdl.org>
> Date: Sun, Dec 17, 2006 at 03:05:39AM -0800
> > On Sun, 17 Dec 2006 12:00:12 +0100
> > "Rafael J. Wysocki" <rjw@sisk.pl> wrote:
> >
> > > Okay, I have identified the patch that causes the problem to appear, which is
> > >
> > > fix-sense-key-medium-error-processing-and-retry.patch
> > >
> > > With this patch reverted -rc1-mm1 is happily running on my test box.
> >
> > That was rather unexpected. Thanks.
> >
> I can confirm that 2.6.20-rc1-mm1 with this patch reverted mounts my
> raid6 partition without problems. This is x86_64 with SMP.
>
The reason was that my dev tree was tainted by this bug:
if (good_bytes &&
- scsi_end_request(cmd, 1, good_bytes, !!result) == NULL)
+ scsi_end_request(cmd, 1, good_bytes, result == 0) == NULL)
return;
in scsi_io_completion(). I had there !!result which is wrong, and when
I diffed against master, it produced a bad patch.
As James mentioned one of the chunks is good and can go in.
Luben
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm]
2006-12-19 23:26 ` Luben Tuikov
@ 2006-12-20 0:08 ` Andrew Morton
0 siblings, 0 replies; 27+ messages in thread
From: Andrew Morton @ 2006-12-20 0:08 UTC (permalink / raw)
To: ltuikov
Cc: Jurriaan, Rafael J. Wysocki, Jeff Garzik, Neil Brown,
linux-kernel, linux-raid, Tejun Heo, Alan
On Tue, 19 Dec 2006 15:26:00 -0800 (PST)
Luben Tuikov <ltuikov@yahoo.com> wrote:
> The reason was that my dev tree was tainted by this bug:
>
> if (good_bytes &&
> - scsi_end_request(cmd, 1, good_bytes, !!result) == NULL)
> + scsi_end_request(cmd, 1, good_bytes, result == 0) == NULL)
> return;
>
> in scsi_io_completion(). I had there !!result which is wrong, and when
> I diffed against master, it produced a bad patch.
Oh. I thought that got sorted out. It's a shame this wasn't made clear to
me..
> As James mentioned one of the chunks is good and can go in.
Please send a new patch, not referential to any previous patch or email,
including full changelogging.
^ permalink raw reply [flat|nested] 27+ messages in thread
end of thread, other threads:[~2006-12-20 0:09 UTC | newest]
Thread overview: 27+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <20061204203410.6152efec.akpm@osdl.org>
[not found] ` <17780.63770.228659.234534@cse.unsw.edu.au>
[not found] ` <20061205061623.GA13749@amd64.of.nowhere>
[not found] ` <20061205062142.GA14784@amd64.of.nowhere>
[not found] ` <20061204224323.2e5d0494.akpm@osdl.org>
[not found] ` <20061205105928.GA6482@amd64.of.nowhere>
[not found] ` <17782.28505.303064.964551@cse.unsw.edu.au>
2006-12-15 19:21 ` md patches in -mm thunder7
2006-12-15 20:06 ` Andrew Morton
2006-12-15 20:50 ` sata badness in 2.6.20-rc1? [Was: Re: md patches in -mm] Neil Brown
2006-12-15 21:05 ` Andrew Morton
2006-12-15 21:18 ` Rafael J. Wysocki
2006-12-15 21:39 ` Andrew Morton
2006-12-15 21:46 ` Rafael J. Wysocki
2006-12-15 22:06 ` Alan
2006-12-15 22:04 ` Rafael J. Wysocki
2006-12-15 22:19 ` Jeff Garzik
2006-12-15 22:27 ` Rafael J. Wysocki
2006-12-15 22:22 ` Rafael J. Wysocki
2006-12-15 22:24 ` Jeff Garzik
2006-12-15 23:38 ` Rafael J. Wysocki
2006-12-16 9:56 ` Rafael J. Wysocki
2006-12-16 11:16 ` Rafael J. Wysocki
2006-12-17 11:00 ` Rafael J. Wysocki
2006-12-17 11:05 ` Andrew Morton
2006-12-17 16:00 ` thunder7
2006-12-19 23:26 ` Luben Tuikov
2006-12-20 0:08 ` Andrew Morton
2006-12-17 14:08 ` Jiri Slaby
2006-12-15 21:48 ` Jeff Garzik
2006-12-16 6:03 ` thunder7
2006-12-15 21:15 ` Rafael J. Wysocki
2006-12-15 21:49 ` Jeff Garzik
2006-12-15 21:56 ` Rafael J. Wysocki
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).