* Problems with mainboard INTEL D201GLY2A, pci devices only available with acpi=noirq
@ 2008-05-14 5:58 Robert Goldner
2008-05-14 8:10 ` Andrew Morton
0 siblings, 1 reply; 4+ messages in thread
From: Robert Goldner @ 2008-05-14 5:58 UTC (permalink / raw)
To: linux-kernel
Hi everyone,
I use a INTEL D201GLY2A mainboard, and after serveral trys PCI devices
were only useable (not visable) with the boot-parameter acpi=noirq (or
noacpi). I tryed several kernel-versions (stated with 2.6.22), and no
sucess without his parameter.
Without acpi=noirq all pci devices are deteced well, but if you want to
use them, there is no response.
So, now some (as I thnik) relevant informations:
lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 662 Host (rev 01)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SiS AGP Port
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS964 [MuTIOL
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS]
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1
00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.1
00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI
00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA (rev 01)
00:06.0 Ethernet controller: Atheros Communications Inc. AR5212/AR5213
00:1f.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS]
.config (I did not attach all information about drivers, because I don´t
think that this is relevant)
CONFIG_X86_32=y
CONFIG_X86=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_FAST_CMPXCHG_LOCAL=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_DMI=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_ARCH_HAS_CPU_RELAX=y
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_ARCH_SUPPORTS_AOUT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_KTIME_SCALAR=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_AUDIT=y
CONFIG_IKCONFIG=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_GROUP_SCHED=y
CONFIG_FAIR_GROUP_SCHED=y
CONFIG_USER_SCHED=y
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_NAMESPACES=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_SYSCTL=y
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLAB=y
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_KMOD=y
CONFIG_BLOCK=y
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_DEFAULT_CFQ=y
CONFIG_DEFAULT_IOSCHED="cfq"
CONFIG_CLASSIC_RCU=y
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_X86_PC=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_MPENTIUM4=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_X86_XADD=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_P6_NOP=y
CONFIG_X86_TSC=y
CONFIG_X86_CMOV=y
CONFIG_X86_MINIMUM_CPU_FAMILY=6
CONFIG_X86_DEBUGCTLMSR=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_PREEMPT_NONE=y
CONFIG_VM86=y
CONFIG_X86_MSR=y
CONFIG_NOHIGHMEM=y
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_VIRT_TO_BUS=y
CONFIG_MTRR=y
CONFIG_EFI=y
CONFIG_HZ_100=y
CONFIG_HZ=100
CONFIG_SCHED_HRTICK=y
CONFIG_PHYSICAL_START=0x100000
CONFIG_PHYSICAL_ALIGN=0x100000
CONFIG_PM=y
CONFIG_PM_LEGACY=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_PROCFS=y
CONFIG_ACPI_PROCFS_POWER=y
CONFIG_ACPI_SYSFS_POWER=y
CONFIG_ACPI_PROC_EVENT=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_DOCK=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_CUSTOM_DSDT_FILE=""
CONFIG_ACPI_BLACKLIST_YEAR=0
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
CONFIG_CPU_IDLE_GOV_MENU=y
CONFIG_PCI=y
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCIEPORTBUS=y
CONFIG_PCIEAER=y
CONFIG_PCI_LEGACY=y
CONFIG_ISA_DMA_API=y
CONFIG_BINFMT_ELF=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_NET_KEY=y
CONFIG_INET=y
CONFIG_IP_FIB_HASH=y
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
CONFIG_NETFILTER=y
CONFIG_NETFILTER_ADVANCED=y
CONFIG_NETFILTER_XTABLES=y
CONFIG_IP_NF_IPTABLES=y
CONFIG_IP_NF_FILTER=y
CONFIG_IP_NF_TARGET_REJECT=y
CONFIG_IP_NF_TARGET_LOG=y
CONFIG_CFG80211=y
CONFIG_WIRELESS_EXT=y
CONFIG_IEEE80211=y
CONFIG_IEEE80211_CRYPT_WEP=y
CONFIG_IEEE80211_CRYPT_CCMP=y
CONFIG_IEEE80211_CRYPT_TKIP=y
CONFIG_IEEE80211_SOFTMAC=y
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
CONFIG_PARPORT_PC_FIFO=y
CONFIG_PARPORT_PC_SUPERIO=y
CONFIG_PNP=y
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_HAVE_IDE=y
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y
CONFIG_BLK_DEV_IDEACPI=y
CONFIG_IDE_PROC_FS=y
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEDMA_SFF=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_BLK_DEV_SIS5513=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDE_ARCH_OBSOLETE_INIT=y
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_SG=y
CONFIG_SCSI_WAIT_SCAN=m
CONFIG_ATA=y
CONFIG_ATA_ACPI=y
CONFIG_SATA_AHCI=y
CONFIG_SATA_SIS=y
CONFIG_PATA_SIS=y
CONFIG_IEEE1394=y
CONFIG_IEEE1394_OHCI1394=y
CONFIG_NETDEVICES=y
CONFIG_TUN=y
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
CONFIG_NET_PCI=y
CONFIG_SIS900=y
....
dmesg without! acpi=noirq:
Linux version 2.6.25-berta (root@hepto) (gcc version 4.2.3 (Debian
4.2.3-2)) #21 Tue May 13 20:10:08 CEST 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003d135000 (usable)
BIOS-e820: 000000003d135000 - 000000003d236000 (ACPI NVS)
BIOS-e820: 000000003d236000 - 000000003ddf2000 (usable)
BIOS-e820: 000000003ddf2000 - 000000003ddf4000 (reserved)
BIOS-e820: 000000003ddf4000 - 000000003de79000 (usable)
BIOS-e820: 000000003de79000 - 000000003def7000 (ACPI NVS)
BIOS-e820: 000000003def7000 - 000000003def8000 (usable)
BIOS-e820: 000000003def8000 - 000000003deff000 (ACPI data)
BIOS-e820: 000000003deff000 - 000000003df00000 (usable)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
Entering add_active_range(0, 0, 229376) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 229376
On node 0 totalpages: 229376
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
DMI 2.4 present.
ACPI: RSDP 000FE020, 0014 (r0 INTEL )
ACPI: RSDT 3DEFE038, 002C (r1 INTEL DG965CO 7A 1000013)
ACPI: FACP 3DEFD000, 0074 (r1 INTEL DG965CO 7A MSFT 1000013)
ACPI: DSDT 3DEF9000, 30F6 (r1 INTEL DG965CO 7A MSFT 1000013)
ACPI: FACS 3DEBC000, 0040
ACPI: APIC 3DEF8000, 006C (r1 INTEL DG965CO 7A MSFT 1000013)
ACPI: PM-Timer IO Port: 0x808
Allocating PCI resources starting at 40000000 (gap: 3df00000:c2080000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227584
Kernel command line: BOOT_IMAGE=2.6.25-berta root=301 lang=de
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1200.099 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 904240k/917504k available (3212k kernel code, 12776k reserved,
1149k data, 224k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffff6000 - 0xfffff000 ( 36 kB)
vmalloc : 0xf8800000 - 0xffff4000 ( 119 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0546000 - 0xc057e000 ( 224 kB)
.data : 0xc0423328 - 0xc0542838 (1149 kB)
.text : 0xc0100000 - 0xc0423328 (3212 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
Calibrating delay using timer specific routine.. 2401.29 BogoMIPS
(lpj=12006493)
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 512K
using mwait in idle threads.
Compat vDSO mapped to ffffe000.
CPU: Intel(R) Celeron(R) CPU 220 @ 1.20GHz stepping 01
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 0k freed
ACPI: Core revision 20070126
ACPI: setting ELCR to 0200 (from 0c00)
net_namespace: 440 bytes
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
system 00:08: ioport range 0x800-0x8fe has been reserved
system 00:08: ioport range 0x8ff-0x8ff has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x4d6-0x4d6 has been reserved
system 00:08: ioport range 0x295-0x29e has been reserved
system 00:08: ioport range 0x2e8-0x2ef has been reserved
system 00:08: ioport range 0x481-0x48f has been reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0xec000-0xfffff could not be reserved
system 00:09: iomem range 0x100000-0x3dffffff could not be reserved
system 00:09: iomem range 0xe0000000-0xefffffff has been reserved
system 00:09: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 1000-1fff
MEM window: 0x4a000000-0x4a0fffff
PREFETCH window: 0x0000000040000000-0x0000000047ffffff
PCI: Bridge: 0000:00:1f.0
IO window: disabled.
MEM window: 0x3e000000-0x3e0fffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:1f.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:1f.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
type=2000 audit(1210710476.299:1): initialized
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
PCI: Setting latency timer of device 0000:00:1f.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1f.0:pcie00]
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
agpgart: Detected SiS chipset - id:1634
agpgart: AGP aperture is 32M @ 0x48000000
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 10 (level,
low) -> IRQ 10
PCI: Setting latency timer of device 0000:01:00.0 to 64
[drm] Initialized sis 1.3.0 20070626 on minor 0
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
loop: module loaded
sis900.c: v1.08.10 Apr. 2 2006
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 19
0000:00:04.0: SiS 900 on Foxconn 661 7MI transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0x2000, IRQ 19, 00:1c:c0:08:08:de
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ath_rate_sample: 1.2 (0.9.4)
ath_pci: 0.9.4
ACPI: Unable to derive IRQ for device 0000:00:06.0
ACPI: PCI Interrupt 0000:00:06.0[A]: no GSI - using IRQ 10
Switched to high resolution mode on CPU 0
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps
24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 7.9 phy 4.5 radio 5.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
failed to automatically load module: wlan_scan_sta; errno: -2
unable to load wlan_scan_sta
wifi0: Atheros 5212: mem=0x4a100000, irq=10
ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
wlan: 0.9.4
wlan: mac acl policy registered
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller (0x1039:0x5513 rev 0x01) at PCI slot 0000:00:02.5
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0x2310-0x2317, BIOS settings: hda:PIO, hdb:PIO
ide1: BM-DMA at 0x2318-0x231f, BIOS settings: hdc:PIO, hdd:PIO
Probing IDE interface ide0...
hda: TRANSCEND, ATA DISK drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 7952112 sectors (4071 MB) w/2KiB Cache, CHS=7889/16/63
hda: hda1
Driver 'sd' needs updating - please use bus_type methods
sata_sis 0000:00:05.0: version 1.0
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 17
sata_sis 0000:00:05.0: Detected SiS 180/181/964 chipset in SATA mode
ACPI: PCI interrupt for device 0000:00:05.0 disabled
sata_sis: probe of 0000:00:05.0 failed with error -22
PCI: Enabling device 0000:00:03.3 (0100 -> 0102)
ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.3: request interrupt 23 failed
ehci_hcd 0000:00:03.3: USB bus 1 deregistered
ACPI: PCI interrupt for device 0000:00:03.3 disabled
ehci_hcd 0000:00:03.3: init 0000:00:03.3 fail, -22
ehci_hcd: probe of 0000:00:03.3 failed with error -22
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:03.0 (0100 -> 0102)
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 20
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:03.0: request interrupt 20 failed
ohci_hcd 0000:00:03.0: USB bus 1 deregistered
ACPI: PCI interrupt for device 0000:00:03.0 disabled
ohci_hcd 0000:00:03.0: init 0000:00:03.0 fail, -22
ohci_hcd: probe of 0000:00:03.0 failed with error -22
PCI: Enabling device 0000:00:03.1 (0100 -> 0102)
ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 21
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:03.1: request interrupt 21 failed
ohci_hcd 0000:00:03.1: USB bus 1 deregistered
ACPI: PCI interrupt for device 0000:00:03.1 disabled
ohci_hcd 0000:00:03.1: init 0000:00:03.1 fail, -22
ohci_hcd: probe of 0000:00:03.1 failed with error -22
PCI: Enabling device 0000:00:03.2 (0100 -> 0102)
ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 22
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:03.2: request interrupt 22 failed
ohci_hcd 0000:00:03.2: USB bus 1 deregistered
ACPI: PCI interrupt for device 0000:00:03.2 disabled
ohci_hcd 0000:00:03.2: init 0000:00:03.2 fail, -22
ohci_hcd: probe of 0000:00:03.2 failed with error -22
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
w83627ehf: Found W83627DHG chip at 0x290
input: AT Translated Set 2 keyboard as /class/input/input2
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.16rc2 (Thu Jan 31
16:40:16 2008 UTC).
ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 18
unable to grab IRQ 18
ACPI: PCI interrupt for device 0000:00:02.7 disabled
Intel ICH: probe of 0000:00:02.7 failed with error -16
ALSA device list:
No soundcards found.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation
<jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'CCMP'
ieee80211_crypt: registered algorithm 'TKIP'
Using IPI Shortcut mode
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
dmesg with acpi=noirq:
Linux version 2.6.25-berta (root@hepto) (gcc version 4.2.3 (Debian
4.2.3-2)) #21 Tue May 13 20:10:08 CEST 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003d135000 (usable)
BIOS-e820: 000000003d135000 - 000000003d236000 (ACPI NVS)
BIOS-e820: 000000003d236000 - 000000003ddf2000 (usable)
BIOS-e820: 000000003ddf2000 - 000000003ddf4000 (reserved)
BIOS-e820: 000000003ddf4000 - 000000003de79000 (usable)
BIOS-e820: 000000003de79000 - 000000003def7000 (ACPI NVS)
BIOS-e820: 000000003def7000 - 000000003def8000 (usable)
BIOS-e820: 000000003def8000 - 000000003deff000 (ACPI data)
BIOS-e820: 000000003deff000 - 000000003df00000 (usable)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
Entering add_active_range(0, 0, 229376) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 229376
On node 0 totalpages: 229376
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
DMI 2.4 present.
ACPI: RSDP 000FE020, 0014 (r0 INTEL )
ACPI: RSDT 3DEFE038, 002C (r1 INTEL DG965CO 7A 1000013)
ACPI: FACP 3DEFD000, 0074 (r1 INTEL DG965CO 7A MSFT 1000013)
ACPI: DSDT 3DEF9000, 30F6 (r1 INTEL DG965CO 7A MSFT 1000013)
ACPI: FACS 3DEBC000, 0040
ACPI: APIC 3DEF8000, 006C (r1 INTEL DG965CO 7A MSFT 1000013)
ACPI: PM-Timer IO Port: 0x808
Allocating PCI resources starting at 40000000 (gap: 3df00000:c2080000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227584
Kernel command line: BOOT_IMAGE=2.6.25-berta root=301 lang=de acpi=noirq
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1200.063 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 904240k/917504k available (3212k kernel code, 12776k reserved,
1149k data, 224k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffff6000 - 0xfffff000 ( 36 kB)
vmalloc : 0xf8800000 - 0xffff4000 ( 119 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0546000 - 0xc057e000 ( 224 kB)
.data : 0xc0423328 - 0xc0542838 (1149 kB)
.text : 0xc0100000 - 0xc0423328 (3212 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
Calibrating delay using timer specific routine.. 2401.29 BogoMIPS
(lpj=12006495)
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 512K
using mwait in idle threads.
Compat vDSO mapped to ffffe000.
CPU: Intel(R) Celeron(R) CPU 220 @ 1.20GHz stepping 01
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 0k freed
ACPI: Core revision 20070126
ACPI: setting ELCR to 0e00 (from 0c00)
net_namespace: 440 bytes
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Using IRQ router default [1039/0964] at 0000:00:02.0
system 00:08: ioport range 0x800-0x8fe has been reserved
system 00:08: ioport range 0x8ff-0x8ff has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x4d6-0x4d6 has been reserved
system 00:08: ioport range 0x295-0x29e has been reserved
system 00:08: ioport range 0x2e8-0x2ef has been reserved
system 00:08: ioport range 0x481-0x48f has been reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0xec000-0xfffff could not be reserved
system 00:09: iomem range 0x100000-0x3dffffff could not be reserved
system 00:09: iomem range 0xe0000000-0xefffffff has been reserved
system 00:09: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 1000-1fff
MEM window: 0x4a000000-0x4a0fffff
PREFETCH window: 0x0000000040000000-0x0000000047ffffff
PCI: Bridge: 0000:00:1f.0
IO window: disabled.
MEM window: 0x3e000000-0x3e0fffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:1f.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:1f.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
type=2000 audit(1210710972.289:1): initialized
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
PCI: Setting latency timer of device 0000:00:1f.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1f.0:pcie00]
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
agpgart: Detected SiS chipset - id:1634
agpgart: AGP aperture is 32M @ 0x48000000
[drm] Initialized drm 1.1.0 20060810
PCI: Setting latency timer of device 0000:01:00.0 to 64
[drm] Initialized sis 1.3.0 20070626 on minor 0
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
loop: module loaded
sis900.c: v1.08.10 Apr. 2 2006
0000:00:04.0: SiS 900 on Foxconn 661 7MI transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0x2000, IRQ 11, 00:1c:c0:08:08:de
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ath_rate_sample: 1.2 (0.9.4)
ath_pci: 0.9.4
Switched to high resolution mode on CPU 0
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps
24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 7.9 phy 4.5 radio 5.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
failed to automatically load module: wlan_scan_sta; errno: -2
unable to load wlan_scan_sta
wifi0: Atheros 5212: mem=0x4a100000, irq=10
ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
wlan: 0.9.4
wlan: mac acl policy registered
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller (0x1039:0x5513 rev 0x01) at PCI slot 0000:00:02.5
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0x2310-0x2317, BIOS settings: hda:PIO, hdb:PIO
ide1: BM-DMA at 0x2318-0x231f, BIOS settings: hdc:PIO, hdd:PIO
Probing IDE interface ide0...
hda: TRANSCEND, ATA DISK drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 7952112 sectors (4071 MB) w/2KiB Cache, CHS=7889/16/63
hda: hda1
Driver 'sd' needs updating - please use bus_type methods
sata_sis 0000:00:05.0: version 1.0
sata_sis 0000:00:05.0: Detected SiS 180/181/964 chipset in SATA mode
scsi0 : sata_sis
scsi1 : sata_sis
ata1: SATA max UDMA/133 cmd 0x2328 ctl 0x2334 bmdma 0x2300 irq 10
ata2: SATA max UDMA/133 cmd 0x2320 ctl 0x2330 bmdma 0x2308 irq 10
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-7: Hitachi HDT725032VLA360, V54OA7EA, max UDMA/133
ata2.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA Hitachi HDT72503 V54O PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2 sda3
sd 1:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg0 type 0
PCI: Enabling device 0000:00:03.3 (0100 -> 0102)
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.3: irq 10, io mem 0x4a111000
ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.25-berta ehci_hcd
usb usb1: SerialNumber: 0000:00:03.3
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:03.0 (0100 -> 0102)
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.0: irq 11, io mem 0x4a114000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.25-berta ohci_hcd
usb usb2: SerialNumber: 0000:00:03.0
PCI: Enabling device 0000:00:03.1 (0100 -> 0102)
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.1: irq 10, io mem 0x4a113000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.25-berta ohci_hcd
usb usb3: SerialNumber: 0000:00:03.1
PCI: Enabling device 0000:00:03.2 (0100 -> 0102)
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:03.2: irq 11, io mem 0x4a112000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.25-berta ohci_hcd
usb usb4: SerialNumber: 0000:00:03.2
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
w83627ehf: Found W83627DHG chip at 0x290
input: AT Translated Set 2 keyboard as /class/input/input2
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.16rc2 (Thu Jan 31
16:40:16 2008 UTC).
intel8x0_measure_ac97_clock: measured 58679 usecs
intel8x0: clocking to 48000
ALSA device list:
#0: SiS SI7012 with AD1888 at irq 11
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation
<jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'CCMP'
ieee80211_crypt: registered algorithm 'TKIP'
Using IPI Shortcut mode
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 224k freed
input: PC Speaker as /class/input/input3
EXT3 FS on hda1, internal journal
So if you have any suggestions, please let me know.
All the best
Robert
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Problems with mainboard INTEL D201GLY2A, pci devices only available with acpi=noirq
2008-05-14 5:58 Problems with mainboard INTEL D201GLY2A, pci devices only available with acpi=noirq Robert Goldner
@ 2008-05-14 8:10 ` Andrew Morton
0 siblings, 0 replies; 4+ messages in thread
From: Andrew Morton @ 2008-05-14 8:10 UTC (permalink / raw)
To: Robert Goldner; +Cc: linux-kernel, linux-acpi
On Wed, 14 May 2008 07:58:42 +0200 Robert Goldner <robert@au-79.de> wrote:
> I use a INTEL D201GLY2A mainboard, and after serveral trys PCI devices
> were only useable (not visable) with the boot-parameter acpi=noirq (or
> noacpi). I tryed several kernel-versions (stated with 2.6.22), and no
> sucess without his parameter.
> Without acpi=noirq all pci devices are deteced well, but if you want to
> use them, there is no response.
>
> So, now some (as I thnik) relevant informations:
> lspci
> 00:00.0 Host bridge: Silicon Integrated Systems [SiS] 662 Host (rev 01)
> 00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SiS AGP Port
> 00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS964 [MuTIOL
> 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev
> 00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS]
> 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1
> 00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1
> 00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.1
> 00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0
> 00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI
> 00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA (rev 01)
> 00:06.0 Ethernet controller: Atheros Communications Inc. AR5212/AR5213
> 00:1f.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
> 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS]
>
>
> .config (I did not attach all information about drivers, because I don__t
> think that this is relevant)
Probably your best approach will be to raise a report against acpi at
bugzilla.kernel.org, please. These things do get fixed, but it takes
some time.
Thanks.
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Problems with mainboard INTEL D201GLY2A, pci devices only available with acpi=noirq
2008-05-15 2:04 ` Robert Hancock
@ 2008-05-15 19:00 ` Robert Goldner
0 siblings, 0 replies; 4+ messages in thread
From: Robert Goldner @ 2008-05-15 19:00 UTC (permalink / raw)
To: linux-kernel; +Cc: Robert Hancock
Robert Hancock schrieb:
> Robert Goldner wrote:
>> Hi everyone,
>>
>> I use a INTEL D201GLY2A mainboard, and after serveral trys PCI devices
>> were only useable (not visable) with the boot-parameter acpi=noirq (or
>> noacpi). I tryed several kernel-versions (stated with 2.6.22), and no
>> sucess without his parameter.
>> Without acpi=noirq all pci devices are deteced well, but if you want
>> to use them, there is no response.
>
> Do you have the latest BIOS on this board? Any nonstandard BIOS
> settings? It looks like the board is not using APIC but the ACPI IRQ
> information is giving out IRQs over 15, which doesn't make any sense.
> Maybe you're running in some kind of broken/untested BIOS configuration.
Yes, it was the latest BIOS for this board, but Intel put a new to the
Internet these days. I updated the Bios, but no change at all.
There is only one ACPI-Relevant switch in the Bios, so I don´t think
that the Bios configuration is the problem. The only on ACPI-relevant
option is:
"Resume from S5 by LAN". But I don´t belive that this makes the problem
(and I tryed both: on and off). There is no way to modify/reservate
interrups in the Bios.
It looks like very buggy ACPI-tables in the Bios.
Robert
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Problems with mainboard INTEL D201GLY2A, pci devices only available with acpi=noirq
[not found] <fa.vWXVKBGhH014XMsboBQBMW6GFwA@ifi.uio.no>
@ 2008-05-15 2:04 ` Robert Hancock
2008-05-15 19:00 ` Robert Goldner
0 siblings, 1 reply; 4+ messages in thread
From: Robert Hancock @ 2008-05-15 2:04 UTC (permalink / raw)
To: Robert Goldner; +Cc: linux-kernel
Robert Goldner wrote:
> Hi everyone,
>
> I use a INTEL D201GLY2A mainboard, and after serveral trys PCI devices
> were only useable (not visable) with the boot-parameter acpi=noirq (or
> noacpi). I tryed several kernel-versions (stated with 2.6.22), and no
> sucess without his parameter.
> Without acpi=noirq all pci devices are deteced well, but if you want to
> use them, there is no response.
Do you have the latest BIOS on this board? Any nonstandard BIOS
settings? It looks like the board is not using APIC but the ACPI IRQ
information is giving out IRQs over 15, which doesn't make any sense.
Maybe you're running in some kind of broken/untested BIOS configuration.
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2008-05-15 19:02 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2008-05-14 5:58 Problems with mainboard INTEL D201GLY2A, pci devices only available with acpi=noirq Robert Goldner
2008-05-14 8:10 ` Andrew Morton
[not found] <fa.vWXVKBGhH014XMsboBQBMW6GFwA@ifi.uio.no>
2008-05-15 2:04 ` Robert Hancock
2008-05-15 19:00 ` Robert Goldner
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).